diff options
Diffstat (limited to 'drivers/net/wireless/ath')
| -rw-r--r-- | drivers/net/wireless/ath/ath9k/hw.h | 9 | ||||
| -rw-r--r-- | drivers/net/wireless/ath/ath9k/phy.c | 166 |
2 files changed, 170 insertions, 5 deletions
diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h index 48b6c71144a..007b41426b2 100644 --- a/drivers/net/wireless/ath/ath9k/hw.h +++ b/drivers/net/wireless/ath/ath9k/hw.h @@ -148,6 +148,15 @@ enum wireless_mode { ATH9K_MODE_MAX, }; +/** + * ath9k_ant_setting - transmit antenna settings + * + * Configures the antenna setting to use for transmit. + * + * @ATH9K_ANT_VARIABLE: this means transmit on all active antennas + * @ATH9K_ANT_FIXED_A: this means transmit on the first antenna only + * @ATH9K_ANT_FIXED_B: this means transmit on the second antenna only + */ enum ath9k_ant_setting { ATH9K_ANT_VARIABLE = 0, ATH9K_ANT_FIXED_A, diff --git a/drivers/net/wireless/ath/ath9k/phy.c b/drivers/net/wireless/ath/ath9k/phy.c index 72a17c43a5a..9e515033b87 100644 --- a/drivers/net/wireless/ath/ath9k/phy.c +++ b/drivers/net/wireless/ath/ath9k/phy.c @@ -14,8 +14,44 @@ * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. */ +/** + * DOC: Programming Atheros 802.11n analog front end radios + * + * AR5416 MAC based PCI devices and AR518 MAC based PCI-Express + * devices have either an external AR2133 analog front end radio for single + * band 2.4 GHz communication or an AR5133 analog front end radio for dual + * band 2.4 GHz / 5 GHz communication. + * + * All devices after the AR5416 and AR5418 family starting with the AR9280 + * have their analog front radios, MAC/BB and host PCIe/USB interface embedded + * into a single-chip and require less programming. + * + * The following single-chips exist with a respective embedded radio: + * + * AR9280 - 11n dual-band 2x2 MIMO for PCIe + * AR9281 - 11n single-band 1x2 MIMO for PCIe + * AR9285 - 11n single-band 1x1 for PCIe + * AR9287 - 11n single-band 2x2 MIMO for PCIe + * + * AR9220 - 11n dual-band 2x2 MIMO for PCI + * AR9223 - 11n single-band 2x2 MIMO for PCI + * + * AR9287 - 11n single-band 1x1 MIMO for USB + */ + #include "hw.h" +/** + * ath9k_hw_write_regs - ?? + * + * @ah: atheros hardware structure + * @modesIndex: + * @freqIndex: + * @regWrites: + * + * Used for both the chipsets with an external AR2133/AR5133 radios and + * single-chip devices. + */ void ath9k_hw_write_regs(struct ath_hw *ah, u32 modesIndex, u32 freqIndex, int regWrites) @@ -23,6 +59,15 @@ ath9k_hw_write_regs(struct ath_hw *ah, u32 modesIndex, u32 freqIndex, REG_WRITE_ARRAY(&ah->iniBB_RfGain, freqIndex, regWrites); } +/** + * ath9k_hw_set_channel - tune to a channel on the external AR2133/AR5133 radios + * @ah: atheros hardware stucture + * @chan: + * + * For the external AR2133/AR5133 radios, takes the MHz channel value and set + * the channel value. Assumes writes enabled to analog bus and bank6 register + * cache in ah->analogBank6Data. + */ bool ath9k_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan) { @@ -97,6 +142,27 @@ ath9k_hw_set_channel(struct ath_hw *ah, struct ath9k_channel *chan) return true; } +/** + * ath9k_hw_ar9280_set_channel - set channel on single-chip device + * @ah: atheros hardware structure + * @chan: + * + * This is the function to change channel on single-chip devices, that is + * all devices after ar9280. + * + * This function takes the channel value in MHz and sets + * hardware channel value. Assumes writes have been enabled to analog bus. + * + * Actual Expression, + * + * For 2GHz channel, + * Channel Frequency = (3/4) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^17) + * (freq_ref = 40MHz) + * + * For 5GHz channel, + * Channel Frequency = (3/2) * freq_ref * (chansel[8:0] + chanfrac[16:0]/2^10) + * (freq_ref = 40MHz/(24>>amodeRefSel)) + */ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, struct ath9k_channel *chan) { @@ -111,7 +177,7 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, reg32 = REG_READ(ah, AR_PHY_SYNTH_CONTROL); reg32 &= 0xc0000000; - if (freq < 4800) { + if (freq < 4800) { /* 2 GHz, fractional mode */ u32 txctl; int regWrites = 0; @@ -122,6 +188,7 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, if (AR_SREV_9287_11_OR_LATER(ah)) { if (freq == 2484) { + /* Enable channel spreading for channel 14 */ REG_WRITE_ARRAY(&ah->iniCckfirJapan2484, 1, regWrites); } else { @@ -155,10 +222,15 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, case 1: default: aModeRefSel = 0; + /* + * Enable 2G (fractional) mode for channels + * which are 5MHz spaced. + */ fracMode = 1; refDivA = 1; channelSel = (freq * 0x8000) / 15; + /* RefDivA setting */ REG_RMW_FIELD(ah, AR_AN_SYNTH9, AR_AN_SYNTH9_REFDIVA, refDivA); @@ -182,6 +254,17 @@ void ath9k_hw_ar9280_set_channel(struct ath_hw *ah, ah->curchan_rad_index = -1; } +/** + * ath9k_phy_modify_rx_buffer() - perform analog swizzling of parameters + * @rfbuf: + * @reg32: + * @numBits: + * @firstBit: + * @column: + * + * Performs analog "swizzling" of parameters into their location. + * Used on external AR2133/AR5133 radios. + */ static void ath9k_phy_modify_rx_buffer(u32 *rfBuf, u32 reg32, u32 numBits, u32 firstBit, @@ -209,6 +292,18 @@ ath9k_phy_modify_rx_buffer(u32 *rfBuf, u32 reg32, } } +/* * + * ath9k_hw_set_rf_regs - programs rf registers based on EEPROM + * @ah: atheros hardware structure + * @chan: + * @modesIndex: + * + * Used for the external AR2133/AR5133 radios. + * + * Reads the EEPROM header info from the device structure and programs + * all rf registers. This routine requires access to the analog + * rf device. This is not required for single-chip devices. + */ bool ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, u16 modesIndex) @@ -218,17 +313,27 @@ ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, u32 ob2GHz = 0, db2GHz = 0; int regWrites = 0; + /* + * Software does not need to program bank data + * for single chip devices, that is AR9280 or anything + * after that. + */ if (AR_SREV_9280_10_OR_LATER(ah)) return true; + /* Setup rf parameters */ eepMinorRev = ah->eep_ops->get_eeprom(ah, EEP_MINOR_REV); + /* Setup Bank 0 Write */ RF_BANK_SETUP(ah->analogBank0Data, &ah->iniBank0, 1); + /* Setup Bank 1 Write */ RF_BANK_SETUP(ah->analogBank1Data, &ah->iniBank1, 1); + /* Setup Bank 2 Write */ RF_BANK_SETUP(ah->analogBank2Data, &ah->iniBank2, 1); + /* Setup Bank 6 Write */ RF_BANK_SETUP(ah->analogBank3Data, &ah->iniBank3, modesIndex); { @@ -239,6 +344,7 @@ ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, } } + /* Only the 5 or 2 GHz OB/DB need to be set for a mode */ if (eepMinorRev >= 2) { if (IS_CHAN_2GHZ(chan)) { ob2GHz = ah->eep_ops->get_eeprom(ah, EEP_OB_2); @@ -257,8 +363,10 @@ ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, } } + /* Setup Bank 7 Setup */ RF_BANK_SETUP(ah->analogBank7Data, &ah->iniBank7, 1); + /* Write Analog registers */ REG_WRITE_RF_ARRAY(&ah->iniBank0, ah->analogBank0Data, regWrites); REG_WRITE_RF_ARRAY(&ah->iniBank1, ah->analogBank1Data, @@ -275,6 +383,11 @@ ath9k_hw_set_rf_regs(struct ath_hw *ah, struct ath9k_channel *chan, return true; } +/** + * ath9k_hw_rf_free - Free memory for analog bank scratch buffers + * @ah: atheros hardware struture + * For the external AR2133/AR5133 radios. + */ void ath9k_hw_rf_free(struct ath_hw *ah) { @@ -295,6 +408,13 @@ ath9k_hw_rf_free(struct ath_hw *ah) #undef ATH_FREE_BANK } +/** + * ath9k_hw_init_rf - initialize external radio structures + * @ah: atheros hardware structure + * @status: + * + * Only required for older devices with external AR2133/AR5133 radios. + */ bool ath9k_hw_init_rf(struct ath_hw *ah, int *status) { struct ath_common *common = ath9k_hw_common(ah); @@ -360,6 +480,33 @@ bool ath9k_hw_init_rf(struct ath_hw *ah, int *status) return true; } +/** + * ath9k_hw_decrease_chain_power() + * + * @ah: atheros hardware structure + * @chan: + * + * Only used on the AR5416 and AR5418 with the external AR2133/AR5133 radios. + * + * Sets a chain internal RF path to the lowest output power. Any + * further writes to bank6 after this setting will override these + * changes. Thus this function must be the last function in the + * sequence to modify bank 6. + * + * This function must be called after ar5416SetRfRegs() which is + * called from ath9k_hw_process_ini() due to swizzling of bank 6. + * Depends on ah->analogBank6Data being initialized by + * ath9k_hw_set_rf_regs() + * + * Additional additive reduction in power - + * change chain's switch table so chain's tx state is actually the rx + * state value. May produce different results in 2GHz/5GHz as well as + * board to board but in general should be a reduction. + * + * Activated by #ifdef ALTER_SWITCH. Not tried yet. If so, must be + * called after ah->eep_ops->set_board_values() due to RMW of + * PHY_SWITCH_CHAIN_0. + */ void ath9k_hw_decrease_chain_power(struct ath_hw *ah, struct ath9k_channel *chan) { @@ -371,26 +518,35 @@ ath9k_hw_decrease_chain_power(struct ath_hw *ah, struct ath9k_channel *chan) case ATH9K_ANT_FIXED_A: bank6SelMask = (ah->config.antenna_switch_swap & ANTSWAP_AB) ? - REDUCE_CHAIN_0 : REDUCE_CHAIN_1; + REDUCE_CHAIN_0 : /* swapped, reduce chain 0 */ + REDUCE_CHAIN_1; /* normal, select chain 1/2 to reduce */ break; case ATH9K_ANT_FIXED_B: bank6SelMask = (ah->config.antenna_switch_swap & ANTSWAP_AB) ? - REDUCE_CHAIN_1 : REDUCE_CHAIN_0; + REDUCE_CHAIN_1 : /* swapped, reduce chain 1/2 */ + REDUCE_CHAIN_0; /* normal, select chain 0 to reduce */ break; case ATH9K_ANT_VARIABLE: - return; + return; /* do not change anything */ break; default: - return; + return; /* do not change anything */ break; } for (i = 0; i < ah->iniBank6.ia_rows; i++) bank6Temp[i] = ah->analogBank6Data[i]; + /* Write Bank 5 to switch Bank 6 write to selected chain only */ REG_WRITE(ah, AR_PHY_BASE + 0xD8, bank6SelMask); + /* + * Modify Bank6 selected chain to use lowest amplification. + * Modifies the parameters to a value of 1. + * Depends on existing bank 6 values to be cached in + * ah->analogBank6Data + */ ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 189, 0); ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 190, 0); ath9k_phy_modify_rx_buffer(bank6Temp, 1, 1, 191, 0); |