diff options
Diffstat (limited to 'drivers/net/wireless/iwlwifi/iwl-commands.h')
| -rw-r--r-- | drivers/net/wireless/iwlwifi/iwl-commands.h | 28 |
1 files changed, 14 insertions, 14 deletions
diff --git a/drivers/net/wireless/iwlwifi/iwl-commands.h b/drivers/net/wireless/iwlwifi/iwl-commands.h index 56964eeb523..5ab74fc0fd1 100644 --- a/drivers/net/wireless/iwlwifi/iwl-commands.h +++ b/drivers/net/wireless/iwlwifi/iwl-commands.h @@ -134,7 +134,7 @@ enum { REPLY_TX_POWER_DBM_CMD = 0x98, MEASURE_ABORT_NOTIFICATION = 0x99, /* not used */ - /* Bluetooth device coexistance config command */ + /* Bluetooth device coexistence config command */ REPLY_BT_CONFIG = 0x9b, /* Statistics */ @@ -185,7 +185,7 @@ struct iwl_cmd_header { u8 cmd; /* Command ID: REPLY_RXON, etc. */ u8 flags; /* 0:5 reserved, 6 abort, 7 internal */ /* - * The driver sets up the sequence number to values of its chosing. + * The driver sets up the sequence number to values of its choosing. * uCode does not use this value, but passes it back to the driver * when sending the response to each driver-originated command, so * the driver can match the response to the command. Since the values @@ -347,7 +347,7 @@ struct iwl4965_tx_power_db { } __attribute__ ((packed)); /** - * Commad REPLY_TX_POWER_DBM_CMD = 0x98 + * Command REPLY_TX_POWER_DBM_CMD = 0x98 * struct iwl5000_tx_power_dbm_cmd */ #define IWL50_TX_POWER_AUTO 0x7f @@ -383,7 +383,7 @@ struct iwl5000_tx_power_dbm_cmd { * calculating txpower settings: * * 1) Power supply voltage indication. The voltage sensor outputs higher - * values for lower voltage, and vice versa. + * values for lower voltage, and vice verse. * * 2) Temperature measurement parameters, for each of two channel widths * (20 MHz and 40 MHz) supported by the radios. Temperature sensing @@ -622,7 +622,7 @@ struct iwl4965_rxon_cmd { u8 ofdm_ht_dual_stream_basic_rates; } __attribute__ ((packed)); -/* 5000 HW just extend this cmmand */ +/* 5000 HW just extend this command */ struct iwl_rxon_cmd { u8 node_addr[6]; __le16 reserved1; @@ -1113,7 +1113,7 @@ struct iwl4965_rx_non_cfg_phy { #define IWL50_OFDM_RSSI_C_BIT_POS 0 struct iwl5000_non_cfg_phy { - __le32 non_cfg_phy[IWL50_RX_RES_PHY_CNT]; /* upto 8 phy entries */ + __le32 non_cfg_phy[IWL50_RX_RES_PHY_CNT]; /* up to 8 phy entries */ } __attribute__ ((packed)); @@ -1169,7 +1169,7 @@ struct iwl4965_rx_mpdu_res_start { /* REPLY_TX Tx flags field */ -/* 1: Use RTS/CTS protocol or CTS-to-self if spec alows it +/* 1: Use RTS/CTS protocol or CTS-to-self if spec allows it * before this frame. if CTS-to-self required check * RXON_FLG_SELF_CTS_EN status. */ #define TX_CMD_FLG_RTS_CTS_MSK __constant_cpu_to_le32(1 << 0) @@ -1529,7 +1529,7 @@ struct iwl4965_tx_resp { /* * definitions for initial rate index field - * bits [3:0] inital rate index + * bits [3:0] initial rate index * bits [6:4] rate table color, used for the initial rate * bit-7 invalid rate indication * i.e. rate was not chosen from rate table @@ -1768,7 +1768,7 @@ struct iwl_link_qual_agg_params { * match the modulation characteristics of the history set. * * When using block-ack (aggregation), all frames are transmitted at the same - * rate, since there is no per-attempt acknowledgement from the destination + * rate, since there is no per-attempt acknowledgment from the destination * station. The Tx response struct iwl_tx_resp indicates the Tx rate in * rate_n_flags field. After receiving a block-ack, the driver can update * history for the entire block all at once. @@ -1907,7 +1907,7 @@ struct iwl_link_quality_cmd { * * 3945 and 4965 support hardware handshake with Bluetooth device on * same platform. Bluetooth device alerts wireless device when it will Tx; - * wireless device can delay or kill its own Tx to accomodate. + * wireless device can delay or kill its own Tx to accommodate. */ struct iwl4965_bt_cmd { u8 flags; @@ -2069,7 +2069,7 @@ struct iwl4965_spectrum_notification { * '11' Illegal set * * NOTE: if sleep_interval[SLEEP_INTRVL_TABLE_SIZE-1] > DTIM period then - * ucode assume sleep over DTIM is allowed and we don't need to wakeup + * ucode assume sleep over DTIM is allowed and we don't need to wake up * for every DTIM. */ #define IWL_POWER_VEC_SIZE 5 @@ -3017,11 +3017,11 @@ struct iwl_wimax_coex_event_entry { /* COEX flag masks */ -/* Staion table is valid */ +/* Station table is valid */ #define COEX_FLAGS_STA_TABLE_VALID_MSK (0x1) -/* UnMask wakeup src at unassociated sleep */ +/* UnMask wake up src at unassociated sleep */ #define COEX_FLAGS_UNASSOC_WA_UNMASK_MSK (0x4) -/* UnMask wakeup src at associated sleep */ +/* UnMask wake up src at associated sleep */ #define COEX_FLAGS_ASSOC_WA_UNMASK_MSK (0x8) /* Enable CoEx feature. */ #define COEX_FLAGS_COEX_ENABLE_MSK (0x80) |