diff options
Diffstat (limited to 'drivers/net/wireless/libertas')
21 files changed, 1008 insertions, 747 deletions
diff --git a/drivers/net/wireless/libertas/cfg.c b/drivers/net/wireless/libertas/cfg.c index 5caa2ac14d6..5d637af2d7c 100644 --- a/drivers/net/wireless/libertas/cfg.c +++ b/drivers/net/wireless/libertas/cfg.c @@ -6,6 +6,8 @@ * */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/sched.h> #include <linux/wait.h> #include <linux/slab.h> @@ -122,8 +124,10 @@ static u8 lbs_auth_to_authtype(enum nl80211_auth_type auth_type) } -/* Various firmware commands need the list of supported rates, but with - the hight-bit set for basic rates */ +/* + * Various firmware commands need the list of supported rates, but with + * the hight-bit set for basic rates + */ static int lbs_add_rates(u8 *rates) { size_t i; @@ -425,7 +429,7 @@ static int lbs_add_wpa_tlv(u8 *tlv, const u8 *ie, u8 ie_len) return ie_len + 2; } -/*************************************************************************** +/* * Set Channel */ @@ -452,7 +456,7 @@ static int lbs_cfg_set_channel(struct wiphy *wiphy, -/*************************************************************************** +/* * Scanning */ @@ -538,8 +542,10 @@ static int lbs_ret_scan(struct lbs_private *priv, unsigned long dummy, goto done; } - /* Validity check: the TLV holds TSF values with 8 bytes each, so - * the size in the TLV must match the nr_sets value */ + /* + * Validity check: the TLV holds TSF values with 8 bytes each, so + * the size in the TLV must match the nr_sets value + */ i = get_unaligned_le16(tsfdesc); tsfdesc += 2; if (i / 8 != scanresp->nr_sets) { @@ -581,8 +587,10 @@ static int lbs_ret_scan(struct lbs_private *priv, unsigned long dummy, /* To find out the channel, we must parse the IEs */ ie = pos; - /* 6+1+8+2+2: size of BSSID, RSSI, time stamp, beacon - interval, capabilities */ + /* + * 6+1+8+2+2: size of BSSID, RSSI, time stamp, beacon + * interval, capabilities + */ ielen = left = len - (6 + 1 + 8 + 2 + 2); while (left >= 2) { u8 id, elen; @@ -790,7 +798,7 @@ static int lbs_cfg_scan(struct wiphy *wiphy, -/*************************************************************************** +/* * Events */ @@ -825,7 +833,7 @@ void lbs_send_mic_failureevent(struct lbs_private *priv, u32 event) -/*************************************************************************** +/* * Connect/disconnect */ @@ -950,8 +958,10 @@ static int lbs_enable_rsn(struct lbs_private *priv, int enable) * Set WPA/WPA key material */ -/* like "struct cmd_ds_802_11_key_material", but with cmd_header. Once we - * get rid of WEXT, this should go into host.h */ +/* + * like "struct cmd_ds_802_11_key_material", but with cmd_header. Once we + * get rid of WEXT, this should go into host.h + */ struct cmd_key_material { struct cmd_header hdr; @@ -1314,8 +1324,8 @@ static int lbs_cfg_connect(struct wiphy *wiphy, struct net_device *dev, sme->ssid, sme->ssid_len, WLAN_CAPABILITY_ESS, WLAN_CAPABILITY_ESS); if (!bss) { - lbs_pr_err("assoc: bss %pM not in scan results\n", - sme->bssid); + wiphy_err(wiphy, "assoc: bss %pM not in scan results\n", + sme->bssid); ret = -ENOENT; goto done; } @@ -1372,8 +1382,8 @@ static int lbs_cfg_connect(struct wiphy *wiphy, struct net_device *dev, lbs_enable_rsn(priv, sme->crypto.cipher_group != 0); break; default: - lbs_pr_err("unsupported cipher group 0x%x\n", - sme->crypto.cipher_group); + wiphy_err(wiphy, "unsupported cipher group 0x%x\n", + sme->crypto.cipher_group); ret = -ENOTSUPP; goto done; } @@ -1491,7 +1501,7 @@ static int lbs_cfg_add_key(struct wiphy *wiphy, struct net_device *netdev, params->key, params->key_len); break; default: - lbs_pr_err("unhandled cipher 0x%x\n", params->cipher); + wiphy_err(wiphy, "unhandled cipher 0x%x\n", params->cipher); ret = -ENOTSUPP; break; } @@ -1536,7 +1546,7 @@ static int lbs_cfg_del_key(struct wiphy *wiphy, struct net_device *netdev, } -/*************************************************************************** +/* * Get station */ @@ -1581,7 +1591,7 @@ static int lbs_cfg_get_station(struct wiphy *wiphy, struct net_device *dev, -/*************************************************************************** +/* * "Site survey", here just current channel and noise level */ @@ -1614,7 +1624,7 @@ static int lbs_get_survey(struct wiphy *wiphy, struct net_device *dev, -/*************************************************************************** +/* * Change interface */ @@ -1656,11 +1666,12 @@ static int lbs_change_intf(struct wiphy *wiphy, struct net_device *dev, -/*************************************************************************** +/* * IBSS (Ad-Hoc) */ -/* The firmware needs the following bits masked out of the beacon-derived +/* + * The firmware needs the following bits masked out of the beacon-derived * capability field when associating/joining to a BSS: * 9 (QoS), 11 (APSD), 12 (unused), 14 (unused), 15 (unused) */ @@ -1999,7 +2010,7 @@ static int lbs_leave_ibss(struct wiphy *wiphy, struct net_device *dev) -/*************************************************************************** +/* * Initialization */ @@ -2118,13 +2129,13 @@ int lbs_cfg_register(struct lbs_private *priv) ret = wiphy_register(wdev->wiphy); if (ret < 0) - lbs_pr_err("cannot register wiphy device\n"); + pr_err("cannot register wiphy device\n"); priv->wiphy_registered = true; ret = register_netdev(priv->dev); if (ret) - lbs_pr_err("cannot register network device\n"); + pr_err("cannot register network device\n"); INIT_DELAYED_WORK(&priv->scan_work, lbs_scan_worker); diff --git a/drivers/net/wireless/libertas/cmd.c b/drivers/net/wireless/libertas/cmd.c index f3ac62431a3..84566db486d 100644 --- a/drivers/net/wireless/libertas/cmd.c +++ b/drivers/net/wireless/libertas/cmd.c @@ -1,7 +1,7 @@ -/** - * This file contains the handling of command. - * It prepares command and sends it to firmware when it is ready. - */ +/* + * This file contains the handling of command. + * It prepares command and sends it to firmware when it is ready. + */ #include <linux/kfifo.h> #include <linux/sched.h> @@ -16,14 +16,14 @@ #define CAL_RSSI(snr, nf) ((s32)((s32)(snr) + CAL_NF(nf))) /** - * @brief Simple callback that copies response back into command + * lbs_cmd_copyback - Simple callback that copies response back into command * - * @param priv A pointer to struct lbs_private structure - * @param extra A pointer to the original command structure for which - * 'resp' is a response - * @param resp A pointer to the command response + * @priv: A pointer to &struct lbs_private structure + * @extra: A pointer to the original command structure for which + * 'resp' is a response + * @resp: A pointer to the command response * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_cmd_copyback(struct lbs_private *priv, unsigned long extra, struct cmd_header *resp) @@ -38,15 +38,15 @@ int lbs_cmd_copyback(struct lbs_private *priv, unsigned long extra, EXPORT_SYMBOL_GPL(lbs_cmd_copyback); /** - * @brief Simple callback that ignores the result. Use this if - * you just want to send a command to the hardware, but don't + * lbs_cmd_async_callback - Simple callback that ignores the result. + * Use this if you just want to send a command to the hardware, but don't * care for the result. * - * @param priv ignored - * @param extra ignored - * @param resp ignored + * @priv: ignored + * @extra: ignored + * @resp: ignored * - * @return 0 for success + * returns: 0 for success */ static int lbs_cmd_async_callback(struct lbs_private *priv, unsigned long extra, struct cmd_header *resp) @@ -56,10 +56,11 @@ static int lbs_cmd_async_callback(struct lbs_private *priv, unsigned long extra, /** - * @brief Checks whether a command is allowed in Power Save mode + * is_command_allowed_in_ps - tests if a command is allowed in Power Save mode + * + * @cmd: the command ID * - * @param command the command ID - * @return 1 if allowed, 0 if not allowed + * returns: 1 if allowed, 0 if not allowed */ static u8 is_command_allowed_in_ps(u16 cmd) { @@ -75,11 +76,12 @@ static u8 is_command_allowed_in_ps(u16 cmd) } /** - * @brief Updates the hardware details like MAC address and regulatory region + * lbs_update_hw_spec - Updates the hardware details like MAC address + * and regulatory region * - * @param priv A pointer to struct lbs_private structure + * @priv: A pointer to &struct lbs_private structure * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_update_hw_spec(struct lbs_private *priv) { @@ -108,7 +110,7 @@ int lbs_update_hw_spec(struct lbs_private *priv) * CF card firmware 5.0.16p0: cap 0x00000303 * USB dongle firmware 5.110.17p2: cap 0x00000303 */ - lbs_pr_info("%pM, fw %u.%u.%up%u, cap 0x%08x\n", + netdev_info(priv->dev, "%pM, fw %u.%u.%up%u, cap 0x%08x\n", cmd.permanentaddr, priv->fwrelease >> 24 & 0xff, priv->fwrelease >> 16 & 0xff, @@ -139,7 +141,8 @@ int lbs_update_hw_spec(struct lbs_private *priv) /* if it's unidentified region code, use the default (USA) */ if (i >= MRVDRV_MAX_REGION_CODE) { priv->regioncode = 0x10; - lbs_pr_info("unidentified region code; using the default (USA)\n"); + netdev_info(priv->dev, + "unidentified region code; using the default (USA)\n"); } if (priv->current_addr[0] == 0xff) @@ -209,7 +212,7 @@ int lbs_host_sleep_cfg(struct lbs_private *priv, uint32_t criteria, (uint8_t *)&cmd_config.wol_conf, sizeof(struct wol_config)); } else { - lbs_pr_info("HOST_SLEEP_CFG failed %d\n", ret); + netdev_info(priv->dev, "HOST_SLEEP_CFG failed %d\n", ret); } return ret; @@ -217,14 +220,14 @@ int lbs_host_sleep_cfg(struct lbs_private *priv, uint32_t criteria, EXPORT_SYMBOL_GPL(lbs_host_sleep_cfg); /** - * @brief Sets the Power Save mode + * lbs_set_ps_mode - Sets the Power Save mode * - * @param priv A pointer to struct lbs_private structure - * @param cmd_action The Power Save operation (PS_MODE_ACTION_ENTER_PS or + * @priv: A pointer to &struct lbs_private structure + * @cmd_action: The Power Save operation (PS_MODE_ACTION_ENTER_PS or * PS_MODE_ACTION_EXIT_PS) - * @param block Whether to block on a response or not + * @block: Whether to block on a response or not * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_set_ps_mode(struct lbs_private *priv, u16 cmd_action, bool block) { @@ -312,7 +315,7 @@ static int lbs_wait_for_ds_awake(struct lbs_private *priv) if (priv->is_deep_sleep) { if (!wait_event_interruptible_timeout(priv->ds_awake_q, !priv->is_deep_sleep, (10 * HZ))) { - lbs_pr_err("ds_awake_q: timer expired\n"); + netdev_err(priv->dev, "ds_awake_q: timer expired\n"); ret = -1; } } @@ -337,7 +340,7 @@ int lbs_set_deep_sleep(struct lbs_private *priv, int deep_sleep) netif_carrier_off(priv->dev); } } else { - lbs_pr_err("deep sleep: already enabled\n"); + netdev_err(priv->dev, "deep sleep: already enabled\n"); } } else { if (priv->is_deep_sleep) { @@ -347,8 +350,8 @@ int lbs_set_deep_sleep(struct lbs_private *priv, int deep_sleep) if (!ret) { ret = lbs_wait_for_ds_awake(priv); if (ret) - lbs_pr_err("deep sleep: wakeup" - "failed\n"); + netdev_err(priv->dev, + "deep sleep: wakeup failed\n"); } } } @@ -382,8 +385,9 @@ int lbs_set_host_sleep(struct lbs_private *priv, int host_sleep) ret = lbs_host_sleep_cfg(priv, priv->wol_criteria, (struct wol_config *)NULL); if (ret) { - lbs_pr_info("Host sleep configuration failed: " - "%d\n", ret); + netdev_info(priv->dev, + "Host sleep configuration failed: %d\n", + ret); return ret; } if (priv->psstate == PS_STATE_FULL_POWER) { @@ -393,19 +397,21 @@ int lbs_set_host_sleep(struct lbs_private *priv, int host_sleep) sizeof(cmd), lbs_ret_host_sleep_activate, 0); if (ret) - lbs_pr_info("HOST_SLEEP_ACTIVATE " - "failed: %d\n", ret); + netdev_info(priv->dev, + "HOST_SLEEP_ACTIVATE failed: %d\n", + ret); } if (!wait_event_interruptible_timeout( priv->host_sleep_q, priv->is_host_sleep_activated, (10 * HZ))) { - lbs_pr_err("host_sleep_q: timer expired\n"); + netdev_err(priv->dev, + "host_sleep_q: timer expired\n"); ret = -1; } } else { - lbs_pr_err("host sleep: already enabled\n"); + netdev_err(priv->dev, "host sleep: already enabled\n"); } } else { if (priv->is_host_sleep_activated) @@ -417,13 +423,13 @@ int lbs_set_host_sleep(struct lbs_private *priv, int host_sleep) } /** - * @brief Set an SNMP MIB value + * lbs_set_snmp_mib - Set an SNMP MIB value * - * @param priv A pointer to struct lbs_private structure - * @param oid The OID to set in the firmware - * @param val Value to set the OID to + * @priv: A pointer to &struct lbs_private structure + * @oid: The OID to set in the firmware + * @val: Value to set the OID to * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_set_snmp_mib(struct lbs_private *priv, u32 oid, u16 val) { @@ -467,13 +473,13 @@ out: } /** - * @brief Get an SNMP MIB value + * lbs_get_snmp_mib - Get an SNMP MIB value * - * @param priv A pointer to struct lbs_private structure - * @param oid The OID to retrieve from the firmware - * @param out_val Location for the returned value + * @priv: A pointer to &struct lbs_private structure + * @oid: The OID to retrieve from the firmware + * @out_val: Location for the returned value * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_get_snmp_mib(struct lbs_private *priv, u32 oid, u16 *out_val) { @@ -510,14 +516,14 @@ out: } /** - * @brief Get the min, max, and current TX power + * lbs_get_tx_power - Get the min, max, and current TX power * - * @param priv A pointer to struct lbs_private structure - * @param curlevel Current power level in dBm - * @param minlevel Minimum supported power level in dBm (optional) - * @param maxlevel Maximum supported power level in dBm (optional) + * @priv: A pointer to &struct lbs_private structure + * @curlevel: Current power level in dBm + * @minlevel: Minimum supported power level in dBm (optional) + * @maxlevel: Maximum supported power level in dBm (optional) * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_get_tx_power(struct lbs_private *priv, s16 *curlevel, s16 *minlevel, s16 *maxlevel) @@ -545,12 +551,12 @@ int lbs_get_tx_power(struct lbs_private *priv, s16 *curlevel, s16 *minlevel, } /** - * @brief Set the TX power + * lbs_set_tx_power - Set the TX power * - * @param priv A pointer to struct lbs_private structure - * @param dbm The desired power level in dBm + * @priv: A pointer to &struct lbs_private structure + * @dbm: The desired power level in dBm * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_set_tx_power(struct lbs_private *priv, s16 dbm) { @@ -573,12 +579,13 @@ int lbs_set_tx_power(struct lbs_private *priv, s16 dbm) } /** - * @brief Enable or disable monitor mode (only implemented on OLPC usb8388 FW) + * lbs_set_monitor_mode - Enable or disable monitor mode + * (only implemented on OLPC usb8388 FW) * - * @param priv A pointer to struct lbs_private structure - * @param enable 1 to enable monitor mode, 0 to disable + * @priv: A pointer to &struct lbs_private structure + * @enable: 1 to enable monitor mode, 0 to disable * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_set_monitor_mode(struct lbs_private *priv, int enable) { @@ -604,11 +611,11 @@ int lbs_set_monitor_mode(struct lbs_private *priv, int enable) } /** - * @brief Get the radio channel + * lbs_get_channel - Get the radio channel * - * @param priv A pointer to struct lbs_private structure + * @priv: A pointer to &struct lbs_private structure * - * @return The channel on success, error on failure + * returns: The channel on success, error on failure */ static int lbs_get_channel(struct lbs_private *priv) { @@ -650,12 +657,12 @@ int lbs_update_channel(struct lbs_private *priv) } /** - * @brief Set the radio channel + * lbs_set_channel - Set the radio channel * - * @param priv A pointer to struct lbs_private structure - * @param channel The desired channel, or 0 to clear a locked channel + * @priv: A pointer to &struct lbs_private structure + * @channel: The desired channel, or 0 to clear a locked channel * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_set_channel(struct lbs_private *priv, u8 channel) { @@ -686,12 +693,13 @@ out: } /** - * @brief Get current RSSI and noise floor + * lbs_get_rssi - Get current RSSI and noise floor * - * @param priv A pointer to struct lbs_private structure - * @param rssi On successful return, signal level in mBm + * @priv: A pointer to &struct lbs_private structure + * @rssi: On successful return, signal level in mBm + * @nf: On successful return, Noise floor * - * @return The channel on success, error on failure + * returns: The channel on success, error on failure */ int lbs_get_rssi(struct lbs_private *priv, s8 *rssi, s8 *nf) { @@ -719,13 +727,14 @@ int lbs_get_rssi(struct lbs_private *priv, s8 *rssi, s8 *nf) } /** - * @brief Send regulatory and 802.11d domain information to the firmware + * lbs_set_11d_domain_info - Send regulatory and 802.11d domain information + * to the firmware * - * @param priv pointer to struct lbs_private - * @param request cfg80211 regulatory request structure - * @param bands the device's supported bands and channels + * @priv: pointer to &struct lbs_private + * @request: cfg80211 regulatory request structure + * @bands: the device's supported bands and channels * - * @return 0 on success, error code on failure + * returns: 0 on success, error code on failure */ int lbs_set_11d_domain_info(struct lbs_private *priv, struct regulatory_request *request, @@ -842,15 +851,15 @@ int lbs_set_11d_domain_info(struct lbs_private *priv, } /** - * @brief Read a MAC, Baseband, or RF register + * lbs_get_reg - Read a MAC, Baseband, or RF register * - * @param priv pointer to struct lbs_private - * @param cmd register command, one of CMD_MAC_REG_ACCESS, - * CMD_BBP_REG_ACCESS, or CMD_RF_REG_ACCESS - * @param offset byte offset of the register to get - * @param value on success, the value of the register at 'offset' + * @priv: pointer to &struct lbs_private + * @reg: register command, one of CMD_MAC_REG_ACCESS, + * CMD_BBP_REG_ACCESS, or CMD_RF_REG_ACCESS + * @offset: byte offset of the register to get + * @value: on success, the value of the register at 'offset' * - * @return 0 on success, error code on failure + * returns: 0 on success, error code on failure */ int lbs_get_reg(struct lbs_private *priv, u16 reg, u16 offset, u32 *value) { @@ -886,15 +895,15 @@ out: } /** - * @brief Write a MAC, Baseband, or RF register + * lbs_set_reg - Write a MAC, Baseband, or RF register * - * @param priv pointer to struct lbs_private - * @param cmd register command, one of CMD_MAC_REG_ACCESS, - * CMD_BBP_REG_ACCESS, or CMD_RF_REG_ACCESS - * @param offset byte offset of the register to set - * @param value the value to write to the register at 'offset' + * @priv: pointer to &struct lbs_private + * @reg: register command, one of CMD_MAC_REG_ACCESS, + * CMD_BBP_REG_ACCESS, or CMD_RF_REG_ACCESS + * @offset: byte offset of the register to set + * @value: the value to write to the register at 'offset' * - * @return 0 on success, error code on failure + * returns: 0 on success, error code on failure */ int lbs_set_reg(struct lbs_private *priv, u16 reg, u16 offset, u32 value) { @@ -1002,7 +1011,8 @@ static void lbs_submit_command(struct lbs_private *priv, ret = priv->hw_host_to_card(priv, MVMS_CMD, (u8 *) cmd, cmdsize); if (ret) { - lbs_pr_info("DNLD_CMD: hw_host_to_card failed: %d\n", ret); + netdev_info(priv->dev, "DNLD_CMD: hw_host_to_card failed: %d\n", + ret); /* Let the timer kick in and retry, and potentially reset the whole thing if the condition persists */ timeo = HZ/4; @@ -1023,7 +1033,7 @@ static void lbs_submit_command(struct lbs_private *priv, lbs_deb_leave(LBS_DEB_HOST); } -/** +/* * This function inserts command node to cmdfreeq * after cleans it. Requires priv->driver_lock held. */ @@ -1125,11 +1135,12 @@ void lbs_set_mac_control(struct lbs_private *priv) } /** - * @brief This function allocates the command buffer and link - * it to command free queue. + * lbs_allocate_cmd_buffer - allocates the command buffer and links + * it to command free queue + * + * @priv: A pointer to &struct lbs_private structure * - * @param priv A pointer to struct lbs_private structure - * @return 0 or -1 + * returns: 0 for success or -1 on error */ int lbs_allocate_cmd_buffer(struct lbs_private *priv) { @@ -1171,10 +1182,11 @@ done: } /** - * @brief This function frees the command buffer. + * lbs_free_cmd_buffer - free the command buffer * - * @param priv A pointer to struct lbs_private structure - * @return 0 or -1 + * @priv: A pointer to &struct lbs_private structure + * + * returns: 0 for success */ int lbs_free_cmd_buffer(struct lbs_private *priv) { @@ -1211,11 +1223,13 @@ done: } /** - * @brief This function gets a free command node if available in - * command free queue. + * lbs_get_free_cmd_node - gets a free command node if available in + * command free queue + * + * @priv: A pointer to &struct lbs_private structure * - * @param priv A pointer to struct lbs_private structure - * @return cmd_ctrl_node A pointer to cmd_ctrl_node structure or NULL + * returns: A pointer to &cmd_ctrl_node structure on success + * or %NULL on error */ static struct cmd_ctrl_node *lbs_get_free_cmd_node(struct lbs_private *priv) { @@ -1245,12 +1259,12 @@ static struct cmd_ctrl_node *lbs_get_free_cmd_node(struct lbs_private *priv) } /** - * @brief This function executes next command in command - * pending queue. It will put firmware back to PS mode - * if applicable. + * lbs_execute_next_command - execute next command in command + * pending queue. Will put firmware back to PS mode if applicable. * - * @param priv A pointer to struct lbs_private structure - * @return 0 or -1 + * @priv: A pointer to &struct lbs_private structure + * + * returns: 0 on success or -1 on error */ int lbs_execute_next_command(struct lbs_private *priv) { @@ -1267,7 +1281,8 @@ int lbs_execute_next_command(struct lbs_private *priv) spin_lock_irqsave(&priv->driver_lock, flags); if (priv->cur_cmd) { - lbs_pr_alert( "EXEC_NEXT_CMD: already processing command!\n"); + netdev_alert(priv->dev, + "EXEC_NEXT_CMD: already processing command!\n"); spin_unlock_irqrestore(&priv->driver_lock, flags); ret = -1; goto done; @@ -1431,7 +1446,7 @@ static void lbs_send_confirmsleep(struct lbs_private *priv) ret = priv->hw_host_to_card(priv, MVMS_CMD, (u8 *) &confirm_sleep, sizeof(confirm_sleep)); if (ret) { - lbs_pr_alert("confirm_sleep failed\n"); + netdev_alert(priv->dev, "confirm_sleep failed\n"); goto out; } @@ -1456,12 +1471,12 @@ out: } /** - * @brief This function checks condition and prepares to - * send sleep confirm command to firmware if ok. + * lbs_ps_confirm_sleep - checks condition and prepares to + * send sleep confirm command to firmware if ok + * + * @priv: A pointer to &struct lbs_private structure * - * @param priv A pointer to struct lbs_private structure - * @param psmode Power Saving mode - * @return n/a + * returns: n/a */ void lbs_ps_confirm_sleep(struct lbs_private *priv) { @@ -1501,16 +1516,16 @@ void lbs_ps_confirm_sleep(struct lbs_private *priv) /** - * @brief Configures the transmission power control functionality. + * lbs_set_tpc_cfg - Configures the transmission power control functionality * - * @param priv A pointer to struct lbs_private structure - * @param enable Transmission power control enable - * @param p0 Power level when link quality is good (dBm). - * @param p1 Power level when link quality is fair (dBm). - * @param p2 Power level when link quality is poor (dBm). - * @param usesnr Use Signal to Noise Ratio in TPC + * @priv: A pointer to &struct lbs_private structure + * @enable: Transmission power control enable + * @p0: Power level when link quality is good (dBm). + * @p1: Power level when link quality is fair (dBm). + * @p2: Power level when link quality is poor (dBm). + * @usesnr: Use Signal to Noise Ratio in TPC * - * @return 0 on success + * returns: 0 on success */ int lbs_set_tpc_cfg(struct lbs_private *priv, int enable, int8_t p0, int8_t p1, int8_t p2, int usesnr) @@ -1533,15 +1548,15 @@ int lbs_set_tpc_cfg(struct lbs_private *priv, int enable, int8_t p0, int8_t p1, } /** - * @brief Configures the power adaptation settings. + * lbs_set_power_adapt_cfg - Configures the power adaptation settings * - * @param priv A pointer to struct lbs_private structure - * @param enable Power adaptation enable - * @param p0 Power level for 1, 2, 5.5 and 11 Mbps (dBm). - * @param p1 Power level for 6, 9, 12, 18, 22, 24 and 36 Mbps (dBm). - * @param p2 Power level for 48 and 54 Mbps (dBm). + * @priv: A pointer to &struct lbs_private structure + * @enable: Power adaptation enable + * @p0: Power level for 1, 2, 5.5 and 11 Mbps (dBm). + * @p1: Power level for 6, 9, 12, 18, 22, 24 and 36 Mbps (dBm). + * @p2: Power level for 48 and 54 Mbps (dBm). * - * @return 0 on Success + * returns: 0 on Success */ int lbs_set_power_adapt_cfg(struct lbs_private *priv, int enable, int8_t p0, @@ -1657,7 +1672,7 @@ int __lbs_cmd(struct lbs_private *priv, uint16_t command, spin_lock_irqsave(&priv->driver_lock, flags); ret = cmdnode->result; if (ret) - lbs_pr_info("PREP_CMD: command 0x%04x failed: %d\n", + netdev_info(priv->dev, "PREP_CMD: command 0x%04x failed: %d\n", command, ret); __lbs_cleanup_and_insert_cmd(priv, cmdnode); diff --git a/drivers/net/wireless/libertas/cmdresp.c b/drivers/net/wireless/libertas/cmdresp.c index 5e95da9dcc2..207fc361db8 100644 --- a/drivers/net/wireless/libertas/cmdresp.c +++ b/drivers/net/wireless/libertas/cmdresp.c @@ -1,7 +1,8 @@ -/** - * This file contains the handling of command - * responses as well as events generated by firmware. - */ +/* + * This file contains the handling of command + * responses as well as events generated by firmware. + */ + #include <linux/slab.h> #include <linux/delay.h> #include <linux/sched.h> @@ -12,12 +13,13 @@ #include "cmd.h" /** - * @brief This function handles disconnect event. it - * reports disconnect to upper layer, clean tx/rx packets, - * reset link state etc. + * lbs_mac_event_disconnected - handles disconnect event. It + * reports disconnect to upper layer, clean tx/rx packets, + * reset link state etc. + * + * @priv: A pointer to struct lbs_private structure * - * @param priv A pointer to struct lbs_private structure - * @return n/a + * returns: n/a */ void lbs_mac_event_disconnected(struct lbs_private *priv) { @@ -84,15 +86,18 @@ int lbs_process_command_response(struct lbs_private *priv, u8 *data, u32 len) lbs_deb_hex(LBS_DEB_CMD, "CMD_RESP", (void *) resp, len); if (resp->seqnum != priv->cur_cmd->cmdbuf->seqnum) { - lbs_pr_info("Received CMD_RESP with invalid sequence %d (expected %d)\n", - le16_to_cpu(resp->seqnum), le16_to_cpu(priv->cur_cmd->cmdbuf->seqnum)); + netdev_info(priv->dev, + "Received CMD_RESP with invalid sequence %d (expected %d)\n", + le16_to_cpu(resp->seqnum), + le16_to_cpu(priv->cur_cmd->cmdbuf->seqnum)); spin_unlock_irqrestore(&priv->driver_lock, flags); ret = -1; goto done; } if (respcmd != CMD_RET(curcmd) && respcmd != CMD_RET_802_11_ASSOCIATE && curcmd != CMD_802_11_ASSOCIATE) { - lbs_pr_info("Invalid CMD_RESP %x to command %x!\n", respcmd, curcmd); + netdev_info(priv->dev, "Invalid CMD_RESP %x to command %x!\n", + respcmd, curcmd); spin_unlock_irqrestore(&priv->driver_lock, flags); ret = -1; goto done; @@ -101,7 +106,8 @@ int lbs_process_command_response(struct lbs_private *priv, u8 *data, u32 len) if (resp->result == cpu_to_le16(0x0004)) { /* 0x0004 means -EAGAIN. Drop the response, let it time out and be resubmitted */ - lbs_pr_info("Firmware returns DEFER to command %x. Will let it time out...\n", + netdev_info(priv->dev, + "Firmware returns DEFER to command %x. Will let it time out...\n", le16_to_cpu(resp->command)); spin_unlock_irqrestore(&priv->driver_lock, flags); ret = -1; @@ -313,28 +319,28 @@ int lbs_process_event(struct lbs_private *priv, u32 event) lbs_deb_cmd("EVENT: ADHOC beacon lost\n"); break; case MACREG_INT_CODE_RSSI_LOW: - lbs_pr_alert("EVENT: rssi low\n"); + netdev_alert(priv->dev, "EVENT: rssi low\n"); break; case MACREG_INT_CODE_SNR_LOW: - lbs_pr_alert("EVENT: snr low\n"); + netdev_alert(priv->dev, "EVENT: snr low\n"); break; case MACREG_INT_CODE_MAX_FAIL: - lbs_pr_alert("EVENT: max fail\n"); + netdev_alert(priv->dev, "EVENT: max fail\n"); break; case MACREG_INT_CODE_RSSI_HIGH: - lbs_pr_alert("EVENT: rssi high\n"); + netdev_alert(priv->dev, "EVENT: rssi high\n"); break; case MACREG_INT_CODE_SNR_HIGH: - lbs_pr_alert("EVENT: snr high\n"); + netdev_alert(priv->dev, "EVENT: snr high\n"); break; case MACREG_INT_CODE_MESH_AUTO_STARTED: /* Ignore spurious autostart events */ - lbs_pr_info("EVENT: MESH_AUTO_STARTED (ignoring)\n"); + netdev_info(priv->dev, "EVENT: MESH_AUTO_STARTED (ignoring)\n"); break; default: - lbs_pr_alert("EVENT: unknown event id %d\n", event); + netdev_alert(priv->dev, "EVENT: unknown event id %d\n", event); break; } diff --git a/drivers/net/wireless/libertas/debugfs.c b/drivers/net/wireless/libertas/debugfs.c index fbf3b0332bb..23250f62176 100644 --- a/drivers/net/wireless/libertas/debugfs.c +++ b/drivers/net/wireless/libertas/debugfs.c @@ -151,13 +151,14 @@ static ssize_t lbs_host_sleep_write(struct file *file, ret = lbs_set_host_sleep(priv, 0); else if (host_sleep == 1) { if (priv->wol_criteria == EHS_REMOVE_WAKEUP) { - lbs_pr_info("wake parameters not configured"); + netdev_info(priv->dev, + "wake parameters not configured\n"); ret = -EINVAL; goto out_unlock; } ret = lbs_set_host_sleep(priv, 1); } else { - lbs_pr_err("invalid option\n"); + netdev_err(priv->dev, "invalid option\n"); ret = -EINVAL; } @@ -849,15 +850,14 @@ static struct debug_data items[] = { static int num_of_items = ARRAY_SIZE(items); /** - * @brief proc read function + * lbs_debugfs_read - proc read function * - * @param page pointer to buffer - * @param s read data starting position - * @param off offset - * @param cnt counter - * @param eof end of file flag - * @param data data to output - * @return number of output data + * @file: file to read + * @userbuf: pointer to buffer + * @count: number of bytes to read + * @ppos: read data starting position + * + * returns: amount of data read or negative error code */ static ssize_t lbs_debugfs_read(struct file *file, char __user *userbuf, size_t count, loff_t *ppos) @@ -897,13 +897,14 @@ static ssize_t lbs_debugfs_read(struct file *file, char __user *userbuf, } /** - * @brief proc write function + * lbs_debugfs_write - proc write function + * + * @f: file pointer + * @buf: pointer to data buffer + * @cnt: data number to write + * @ppos: file position * - * @param f file pointer - * @param buf pointer to data buffer - * @param cnt data number to write - * @param data data to write - * @return number of data + * returns: amount of data written */ static ssize_t lbs_debugfs_write(struct file *f, const char __user *buf, size_t cnt, loff_t *ppos) @@ -966,11 +967,11 @@ static const struct file_operations lbs_debug_fops = { }; /** - * @brief create debug proc file + * lbs_debug_init - create debug proc file + * + * @priv: pointer to &struct lbs_private * - * @param priv pointer struct lbs_private - * @param dev pointer net_device - * @return N/A + * returns: N/A */ static void lbs_debug_init(struct lbs_private *priv) { diff --git a/drivers/net/wireless/libertas/decl.h b/drivers/net/wireless/libertas/decl.h index 2ae752d1006..da0b05bb89f 100644 --- a/drivers/net/wireless/libertas/decl.h +++ b/drivers/net/wireless/libertas/decl.h @@ -1,8 +1,8 @@ -/** - * This file contains declaration referring to - * functions defined in other source files - */ +/* + * This file contains declaration referring to + * functions defined in other source files + */ #ifndef _LBS_DECL_H_ #define _LBS_DECL_H_ diff --git a/drivers/net/wireless/libertas/defs.h b/drivers/net/wireless/libertas/defs.h index d00c728cec4..ab966f08024 100644 --- a/drivers/net/wireless/libertas/defs.h +++ b/drivers/net/wireless/libertas/defs.h @@ -1,7 +1,7 @@ -/** - * This header file contains global constant/enum definitions, - * global variable declaration. - */ +/* + * This header file contains global constant/enum definitions, + * global variable declaration. + */ #ifndef _LBS_DEFS_H_ #define _LBS_DEFS_H_ @@ -89,13 +89,6 @@ do { if ((lbs_debug & (grp)) == (grp)) \ #define lbs_deb_spi(fmt, args...) LBS_DEB_LL(LBS_DEB_SPI, " spi", fmt, ##args) #define lbs_deb_cfg80211(fmt, args...) LBS_DEB_LL(LBS_DEB_CFG80211, " cfg80211", fmt, ##args) -#define lbs_pr_info(format, args...) \ - printk(KERN_INFO DRV_NAME": " format, ## args) -#define lbs_pr_err(format, args...) \ - printk(KERN_ERR DRV_NAME": " format, ## args) -#define lbs_pr_alert(format, args...) \ - printk(KERN_ALERT DRV_NAME": " format, ## args) - #ifdef DEBUG static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, int len) { @@ -123,19 +116,19 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in -/** Buffer Constants */ +/* Buffer Constants */ /* The size of SQ memory PPA, DPA are 8 DWORDs, that keep the physical -* addresses of TxPD buffers. Station has only 8 TxPD available, Whereas -* driver has more local TxPDs. Each TxPD on the host memory is associated -* with a Tx control node. The driver maintains 8 RxPD descriptors for -* station firmware to store Rx packet information. -* -* Current version of MAC has a 32x6 multicast address buffer. -* -* 802.11b can have up to 14 channels, the driver keeps the -* BSSID(MAC address) of each APs or Ad hoc stations it has sensed. -*/ + * addresses of TxPD buffers. Station has only 8 TxPD available, Whereas + * driver has more local TxPDs. Each TxPD on the host memory is associated + * with a Tx control node. The driver maintains 8 RxPD descriptors for + * station firmware to store Rx packet information. + * + * Current version of MAC has a 32x6 multicast address buffer. + * + * 802.11b can have up to 14 channels, the driver keeps the + * BSSID(MAC address) of each APs or Ad hoc stations it has sensed. + */ #define MRVDRV_MAX_MULTICAST_LIST_SIZE 32 #define LBS_NUM_CMD_BUFFERS 10 @@ -166,7 +159,7 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in #define WOL_RESULT_NOSPC_ERR 1 #define WOL_RESULT_EEXIST_ERR 2 -/** Misc constants */ +/* Misc constants */ /* This section defines 802.11 specific contants */ #define MRVDRV_MAX_BSS_DESCRIPTS 16 @@ -183,7 +176,8 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in #define MARVELL_MESH_IE_LENGTH 9 -/* Values used to populate the struct mrvl_mesh_ie. The only time you need this +/* + * Values used to populate the struct mrvl_mesh_ie. The only time you need this * is when enabling the mesh using CMD_MESH_CONFIG. */ #define MARVELL_MESH_IE_TYPE 4 @@ -193,7 +187,7 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in #define MARVELL_MESH_METRIC_ID 0 #define MARVELL_MESH_CAPABILITY 0 -/** INT status Bit Definition*/ +/* INT status Bit Definition */ #define MRVDRV_TX_DNLD_RDY 0x0001 #define MRVDRV_RX_UPLD_RDY 0x0002 #define MRVDRV_CMD_DNLD_RDY 0x0004 @@ -208,59 +202,63 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in #define TPC_DEFAULT_P1 10 #define TPC_DEFAULT_P2 13 -/** TxPD status */ +/* TxPD status */ -/* Station firmware use TxPD status field to report final Tx transmit -* result, Bit masks are used to present combined situations. -*/ +/* + * Station firmware use TxPD status field to report final Tx transmit + * result, Bit masks are used to present combined situations. + */ #define MRVDRV_TxPD_POWER_MGMT_NULL_PACKET 0x01 #define MRVDRV_TxPD_POWER_MGMT_LAST_PACKET 0x08 -/** Tx mesh flag */ -/* Currently we are using normal WDS flag as mesh flag. +/* Tx mesh flag */ +/* + * Currently we are using normal WDS flag as mesh flag. * TODO: change to proper mesh flag when MAC understands it. */ #define TxPD_CONTROL_WDS_FRAME (1<<17) #define TxPD_MESH_FRAME TxPD_CONTROL_WDS_FRAME -/** Mesh interface ID */ +/* Mesh interface ID */ #define MESH_IFACE_ID 0x0001 -/** Mesh id should be in bits 14-13-12 */ +/* Mesh id should be in bits 14-13-12 */ #define MESH_IFACE_BIT_OFFSET 0x000c -/** Mesh enable bit in FW capability */ +/* Mesh enable bit in FW capability */ #define MESH_CAPINFO_ENABLE_MASK (1<<16) -/** FW definition from Marvell v4 */ +/* FW definition from Marvell v4 */ #define MRVL_FW_V4 (0x04) -/** FW definition from Marvell v5 */ +/* FW definition from Marvell v5 */ #define MRVL_FW_V5 (0x05) -/** FW definition from Marvell v10 */ +/* FW definition from Marvell v10 */ #define MRVL_FW_V10 (0x0a) -/** FW major revision definition */ +/* FW major revision definition */ #define MRVL_FW_MAJOR_REV(x) ((x)>>24) -/** RxPD status */ +/* RxPD status */ #define MRVDRV_RXPD_STATUS_OK 0x0001 -/** RxPD status - Received packet types */ -/** Rx mesh flag */ -/* Currently we are using normal WDS flag as mesh flag. +/* RxPD status - Received packet types */ +/* Rx mesh flag */ +/* + * Currently we are using normal WDS flag as mesh flag. * TODO: change to proper mesh flag when MAC understands it. */ #define RxPD_CONTROL_WDS_FRAME (0x40) #define RxPD_MESH_FRAME RxPD_CONTROL_WDS_FRAME -/** RSSI-related defines */ -/* RSSI constants are used to implement 802.11 RSSI threshold -* indication. if the Rx packet signal got too weak for 5 consecutive -* times, miniport driver (driver) will report this event to wrapper -*/ +/* RSSI-related defines */ +/* + * RSSI constants are used to implement 802.11 RSSI threshold + * indication. if the Rx packet signal got too weak for 5 consecutive + * times, miniport driver (driver) will report this event to wrapper + */ #define MRVDRV_NF_DEFAULT_SCAN_VALUE (-96) -/** RTS/FRAG related defines */ +/* RTS/FRAG related defines */ #define MRVDRV_RTS_MIN_VALUE 0 #define MRVDRV_RTS_MAX_VALUE 2347 #define MRVDRV_FRAG_MIN_VALUE 256 @@ -300,36 +298,36 @@ static inline void lbs_deb_hex(unsigned int grp, const char *prompt, u8 *buf, in #define MAX_LEDS 8 -/** Global Variable Declaration */ +/* Global Variable Declaration */ extern const char lbs_driver_version[]; extern u16 lbs_region_code_to_index[MRVDRV_MAX_REGION_CODE]; -/** ENUM definition*/ -/** SNRNF_TYPE */ +/* ENUM definition */ +/* SNRNF_TYPE */ enum SNRNF_TYPE { TYPE_BEACON = 0, TYPE_RXPD, MAX_TYPE_B }; -/** SNRNF_DATA*/ +/* SNRNF_DATA */ enum SNRNF_DATA { TYPE_NOAVG = 0, TYPE_AVG, MAX_TYPE_AVG }; -/** LBS_802_11_POWER_MODE */ +/* LBS_802_11_POWER_MODE */ enum LBS_802_11_POWER_MODE { LBS802_11POWERMODECAM, LBS802_11POWERMODEMAX_PSP, LBS802_11POWERMODEFAST_PSP, - /*not a real mode, defined as an upper bound */ + /* not a real mode, defined as an upper bound */ LBS802_11POWEMODEMAX }; -/** PS_STATE */ +/* PS_STATE */ enum PS_STATE { PS_STATE_FULL_POWER, PS_STATE_AWAKE, @@ -337,7 +335,7 @@ enum PS_STATE { PS_STATE_SLEEP }; -/** DNLD_STATE */ +/* DNLD_STATE */ enum DNLD_STATE { DNLD_RES_RECEIVED, DNLD_DATA_SENT, @@ -345,19 +343,19 @@ enum DNLD_STATE { DNLD_BOOTCMD_SENT, }; -/** LBS_MEDIA_STATE */ +/* LBS_MEDIA_STATE */ enum LBS_MEDIA_STATE { LBS_CONNECTED, LBS_DISCONNECTED }; -/** LBS_802_11_PRIVACY_FILTER */ +/* LBS_802_11_PRIVACY_FILTER */ enum LBS_802_11_PRIVACY_FILTER { LBS802_11PRIVFILTERACCEPTALL, LBS802_11PRIVFILTER8021XWEP }; -/** mv_ms_type */ +/* mv_ms_type */ enum mv_ms_type { MVMS_DAT = 0, MVMS_CMD = 1, @@ -365,14 +363,14 @@ enum mv_ms_type { MVMS_EVENT }; -/** KEY_TYPE_ID */ +/* KEY_TYPE_ID */ enum KEY_TYPE_ID { KEY_TYPE_ID_WEP = 0, KEY_TYPE_ID_TKIP, KEY_TYPE_ID_AES }; -/** KEY_INFO_WPA (applies to both TKIP and AES/CCMP) */ +/* KEY_INFO_WPA (applies to both TKIP and AES/CCMP) */ enum KEY_INFO_WPA { KEY_INFO_WPA_MCAST = 0x01, KEY_INFO_WPA_UNICAST = 0x02, diff --git a/drivers/net/wireless/libertas/dev.h b/drivers/net/wireless/libertas/dev.h index bc461eb3966..76d018beebf 100644 --- a/drivers/net/wireless/libertas/dev.h +++ b/drivers/net/wireless/libertas/dev.h @@ -1,8 +1,8 @@ -/** - * This file contains definitions and data structures specific - * to Marvell 802.11 NIC. It contains the Device Information - * structure struct lbs_private.. - */ +/* + * This file contains definitions and data structures specific + * to Marvell 802.11 NIC. It contains the Device Information + * structure struct lbs_private.. + */ #ifndef _LBS_DEV_H_ #define _LBS_DEV_H_ @@ -12,7 +12,7 @@ #include <linux/kfifo.h> -/** sleep_params */ +/* sleep_params */ struct sleep_params { uint16_t sp_error; uint16_t sp_offset; @@ -23,7 +23,7 @@ struct sleep_params { }; -/** Private structure for the MV device */ +/* Private structure for the MV device */ struct lbs_private { /* Basic networking */ @@ -125,12 +125,12 @@ struct lbs_private { /* Events sent from hardware to driver */ struct kfifo event_fifo; - /** thread to service interrupts */ + /* thread to service interrupts */ struct task_struct *main_thread; wait_queue_head_t waitq; struct workqueue_struct *work_thread; - /** Encryption stuff */ + /* Encryption stuff */ u8 authtype_auto; u8 wep_tx_key; u8 wep_key[4][WLAN_KEY_LEN_WEP104]; @@ -162,7 +162,7 @@ struct lbs_private { s16 txpower_min; s16 txpower_max; - /** Scanning */ + /* Scanning */ struct delayed_work scan_work; int scan_channel; /* Queue of things waiting for scan completion */ diff --git a/drivers/net/wireless/libertas/ethtool.c b/drivers/net/wireless/libertas/ethtool.c index 50193aac679..29dbce4a9f8 100644 --- a/drivers/net/wireless/libertas/ethtool.c +++ b/drivers/net/wireless/libertas/ethtool.c @@ -20,7 +20,8 @@ static void lbs_ethtool_get_drvinfo(struct net_device *dev, strcpy(info->version, lbs_driver_version); } -/* All 8388 parts have 16KiB EEPROM size at the time of writing. +/* + * All 8388 parts have 16KiB EEPROM size at the time of writing. * In case that changes this needs fixing. */ #define LBS_EEPROM_LEN 16384 diff --git a/drivers/net/wireless/libertas/host.h b/drivers/net/wireless/libertas/host.h index 6cb6935ee4a..2e2dbfa2ee5 100644 --- a/drivers/net/wireless/libertas/host.h +++ b/drivers/net/wireless/libertas/host.h @@ -1,7 +1,7 @@ -/** - * This file function prototypes, data structure - * and definitions for all the host/station commands - */ +/* + * This file function prototypes, data structure + * and definitions for all the host/station commands + */ #ifndef _LBS_HOST_H_ #define _LBS_HOST_H_ @@ -13,9 +13,10 @@ #define CMD_OPTION_WAITFORRSP 0x0002 -/** Host command IDs */ +/* Host command IDs */ -/* Return command are almost always the same as the host command, but with +/* + * Return command are almost always the same as the host command, but with * bit 15 set high. There are a few exceptions, though... */ #define CMD_RET(cmd) (0x8000 | cmd) @@ -251,7 +252,7 @@ enum cmd_mesh_config_types { CMD_TYPE_MESH_GET_MESH_IE, /* GET_DEFAULTS is superset of GET_MESHIE */ }; -/** Card Event definition */ +/* Card Event definition */ #define MACREG_INT_CODE_TX_PPA_FREE 0 #define MACREG_INT_CODE_TX_DMA_DONE 1 #define MACREG_INT_CODE_LINK_LOST_W_SCAN 2 @@ -624,12 +625,14 @@ struct cmd_ds_802_11_rf_channel { struct cmd_ds_802_11_rssi { struct cmd_header hdr; - /* request: number of beacons (N) to average the SNR and NF over + /* + * request: number of beacons (N) to average the SNR and NF over * response: SNR of most recent beacon */ __le16 n_or_snr; - /* The following fields are only set in the response. + /* + * The following fields are only set in the response. * In the request these are reserved and should be set to 0. */ __le16 nf; /* most recent beacon noise floor */ @@ -680,14 +683,16 @@ struct cmd_ds_802_11_ps_mode { __le16 action; - /* Interval for keepalive in PS mode: + /* + * Interval for keepalive in PS mode: * 0x0000 = don't change * 0x001E = firmware default * 0xFFFF = disable */ __le16 nullpktinterval; - /* Number of DTIM intervals to wake up for: + /* + * Number of DTIM intervals to wake up for: * 0 = don't change * 1 = firmware default * 5 = max @@ -697,7 +702,8 @@ struct cmd_ds_802_11_ps_mode { __le16 reserved; __le16 locallisteninterval; - /* AdHoc awake period (FW v9+ only): + /* + * AdHoc awake period (FW v9+ only): * 0 = don't change * 1 = always awake (IEEE standard behavior) * 2 - 31 = sleep for (n - 1) periods and awake for 1 period @@ -771,7 +777,8 @@ struct adhoc_bssdesc { __le16 capability; u8 rates[MAX_RATES]; - /* DO NOT ADD ANY FIELDS TO THIS STRUCTURE. It is used below in the + /* + * DO NOT ADD ANY FIELDS TO THIS STRUCTURE. It is used below in the * Adhoc join command and will cause a binary layout mismatch with * the firmware */ diff --git a/drivers/net/wireless/libertas/if_cs.c b/drivers/net/wireless/libertas/if_cs.c index 8712cb213f2..63ed5798365 100644 --- a/drivers/net/wireless/libertas/if_cs.c +++ b/drivers/net/wireless/libertas/if_cs.c @@ -21,6 +21,8 @@ */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/module.h> #include <linux/slab.h> #include <linux/delay.h> @@ -312,7 +314,8 @@ static int if_cs_poll_while_fw_download(struct if_cs_card *card, uint addr, u8 r #define CF8385_MANFID 0x02df #define CF8385_CARDID 0x8103 -/* FIXME: just use the 'driver_info' field of 'struct pcmcia_device_id' when +/* + * FIXME: just use the 'driver_info' field of 'struct pcmcia_device_id' when * that gets fixed. Currently there's no way to access it from the probe hook. */ static inline u32 get_model(u16 manf_id, u16 card_id) @@ -361,7 +364,7 @@ static int if_cs_send_cmd(struct lbs_private *priv, u8 *buf, u16 nb) if (status & IF_CS_BIT_COMMAND) break; if (++loops > 100) { - lbs_pr_err("card not ready for commands\n"); + netdev_err(priv->dev, "card not ready for commands\n"); goto done; } mdelay(1); @@ -431,14 +434,16 @@ static int if_cs_receive_cmdres(struct lbs_private *priv, u8 *data, u32 *len) /* is hardware ready? */ status = if_cs_read16(priv->card, IF_CS_CARD_STATUS); if ((status & IF_CS_BIT_RESP) == 0) { - lbs_pr_err("no cmd response in card\n"); + netdev_err(priv->dev, "no cmd response in card\n"); *len = 0; goto out; } *len = if_cs_read16(priv->card, IF_CS_RESP_LEN); if ((*len == 0) || (*len > LBS_CMD_BUFFER_SIZE)) { - lbs_pr_err("card cmd buffer has invalid # of bytes (%d)\n", *len); + netdev_err(priv->dev, + "card cmd buffer has invalid # of bytes (%d)\n", + *len); goto out; } @@ -472,7 +477,9 @@ static struct sk_buff *if_cs_receive_data(struct lbs_private *priv) len = if_cs_read16(priv->card, IF_CS_READ_LEN); if (len == 0 || len > MRVDRV_ETH_RX_PACKET_BUFFER_SIZE) { - lbs_pr_err("card data buffer has invalid # of bytes (%d)\n", len); + netdev_err(priv->dev, + "card data buffer has invalid # of bytes (%d)\n", + len); priv->dev->stats.rx_dropped++; goto dat_err; } @@ -621,8 +628,10 @@ static int if_cs_prog_helper(struct if_cs_card *card, const struct firmware *fw) if (remain < count) count = remain; - /* "write the number of bytes to be sent to the I/O Command - * write length register" */ + /* + * "write the number of bytes to be sent to the I/O Command + * write length register" + */ if_cs_write16(card, IF_CS_CMD_LEN, count); /* "write this to I/O Command port register as 16 bit writes */ @@ -631,21 +640,27 @@ static int if_cs_prog_helper(struct if_cs_card *card, const struct firmware *fw) &fw->data[sent], count >> 1); - /* "Assert the download over interrupt command in the Host - * status register" */ + /* + * "Assert the download over interrupt command in the Host + * status register" + */ if_cs_write8(card, IF_CS_HOST_STATUS, IF_CS_BIT_COMMAND); - /* "Assert the download over interrupt command in the Card - * interrupt case register" */ + /* + * "Assert the download over interrupt command in the Card + * interrupt case register" + */ if_cs_write16(card, IF_CS_HOST_INT_CAUSE, IF_CS_BIT_COMMAND); - /* "The host polls the Card Status register ... for 50 ms before - declaring a failure */ + /* + * "The host polls the Card Status register ... for 50 ms before + * declaring a failure" + */ ret = if_cs_poll_while_fw_download(card, IF_CS_CARD_STATUS, IF_CS_BIT_COMMAND); if (ret < 0) { - lbs_pr_err("can't download helper at 0x%x, ret %d\n", - sent, ret); + pr_err("can't download helper at 0x%x, ret %d\n", + sent, ret); goto done; } @@ -675,7 +690,7 @@ static int if_cs_prog_real(struct if_cs_card *card, const struct firmware *fw) ret = if_cs_poll_while_fw_download(card, IF_CS_SQ_READ_LOW, IF_CS_SQ_HELPER_OK); if (ret < 0) { - lbs_pr_err("helper firmware doesn't answer\n"); + pr_err("helper firmware doesn't answer\n"); goto done; } @@ -683,13 +698,13 @@ static int if_cs_prog_real(struct if_cs_card *card, const struct firmware *fw) len = if_cs_read16(card, IF_CS_SQ_READ_LOW); if (len & 1) { retry++; - lbs_pr_info("odd, need to retry this firmware block\n"); + pr_info("odd, need to retry this firmware block\n"); } else { retry = 0; } if (retry > 20) { - lbs_pr_err("could not download firmware\n"); + pr_err("could not download firmware\n"); ret = -ENODEV; goto done; } @@ -709,14 +724,14 @@ static int if_cs_prog_real(struct if_cs_card *card, const struct firmware *fw) ret = if_cs_poll_while_fw_download(card, IF_CS_CARD_STATUS, IF_CS_BIT_COMMAND); if (ret < 0) { - lbs_pr_err("can't download firmware at 0x%x\n", sent); + pr_err("can't download firmware at 0x%x\n", sent); goto done; } } ret = if_cs_poll_while_fw_download(card, IF_CS_SCRATCH, 0x5a); if (ret < 0) - lbs_pr_err("firmware download failed\n"); + pr_err("firmware download failed\n"); done: lbs_deb_leave_args(LBS_DEB_CS, "ret %d", ret); @@ -750,7 +765,8 @@ static int if_cs_host_to_card(struct lbs_private *priv, ret = if_cs_send_cmd(priv, buf, nb); break; default: - lbs_pr_err("%s: unsupported type %d\n", __func__, type); + netdev_err(priv->dev, "%s: unsupported type %d\n", + __func__, type); } lbs_deb_leave_args(LBS_DEB_CS, "ret %d", ret); @@ -779,7 +795,7 @@ static int if_cs_ioprobe(struct pcmcia_device *p_dev, void *priv_data) p_dev->resource[0]->flags |= IO_DATA_PATH_WIDTH_AUTO; if (p_dev->resource[1]->end) { - lbs_pr_err("wrong CIS (check number of IO windows)\n"); + pr_err("wrong CIS (check number of IO windows)\n"); return -ENODEV; } @@ -800,7 +816,7 @@ static int if_cs_probe(struct pcmcia_device *p_dev) card = kzalloc(sizeof(struct if_cs_card), GFP_KERNEL); if (!card) { - lbs_pr_err("error in kzalloc\n"); + pr_err("error in kzalloc\n"); goto out; } card->p_dev = p_dev; @@ -809,7 +825,7 @@ static int if_cs_probe(struct pcmcia_device *p_dev) p_dev->config_flags |= CONF_ENABLE_IRQ | CONF_AUTO_SET_IO; if (pcmcia_loop_config(p_dev, if_cs_ioprobe, NULL)) { - lbs_pr_err("error in pcmcia_loop_config\n"); + pr_err("error in pcmcia_loop_config\n"); goto out1; } @@ -825,14 +841,14 @@ static int if_cs_probe(struct pcmcia_device *p_dev) card->iobase = ioport_map(p_dev->resource[0]->start, resource_size(p_dev->resource[0])); if (!card->iobase) { - lbs_pr_err("error in ioport_map\n"); + pr_err("error in ioport_map\n"); ret = -EIO; goto out1; } ret = pcmcia_enable_device(p_dev); if (ret) { - lbs_pr_err("error in pcmcia_enable_device\n"); + pr_err("error in pcmcia_enable_device\n"); goto out2; } @@ -841,14 +857,14 @@ static int if_cs_probe(struct pcmcia_device *p_dev) /* * Most of the libertas cards can do unaligned register access, but some - * weird ones can not. That's especially true for the CF8305 card. + * weird ones cannot. That's especially true for the CF8305 card. */ card->align_regs = 0; card->model = get_model(p_dev->manf_id, p_dev->card_id); if (card->model == MODEL_UNKNOWN) { - lbs_pr_err("unsupported manf_id 0x%04x / card_id 0x%04x\n", - p_dev->manf_id, p_dev->card_id); + pr_err("unsupported manf_id 0x%04x / card_id 0x%04x\n", + p_dev->manf_id, p_dev->card_id); goto out2; } @@ -857,20 +873,20 @@ static int if_cs_probe(struct pcmcia_device *p_dev) if (card->model == MODEL_8305) { card->align_regs = 1; if (prod_id < IF_CS_CF8305_B1_REV) { - lbs_pr_err("8305 rev B0 and older are not supported\n"); + pr_err("8305 rev B0 and older are not supported\n"); ret = -ENODEV; goto out2; } } if ((card->model == MODEL_8381) && prod_id < IF_CS_CF8381_B3_REV) { - lbs_pr_err("8381 rev B2 and older are not supported\n"); + pr_err("8381 rev B2 and older are not supported\n"); ret = -ENODEV; goto out2; } if ((card->model == MODEL_8385) && prod_id < IF_CS_CF8385_B1_REV) { - lbs_pr_err("8385 rev B0 and older are not supported\n"); + pr_err("8385 rev B0 and older are not supported\n"); ret = -ENODEV; goto out2; } @@ -878,7 +894,7 @@ static int if_cs_probe(struct pcmcia_device *p_dev) ret = lbs_get_firmware(&p_dev->dev, NULL, NULL, card->model, &fw_table[0], &helper, &mainfw); if (ret) { - lbs_pr_err("failed to find firmware (%d)\n", ret); + pr_err("failed to find firmware (%d)\n", ret); goto out2; } @@ -909,18 +925,20 @@ static int if_cs_probe(struct pcmcia_device *p_dev) ret = request_irq(p_dev->irq, if_cs_interrupt, IRQF_SHARED, DRV_NAME, card); if (ret) { - lbs_pr_err("error in request_irq\n"); + pr_err("error in request_irq\n"); goto out3; } - /* Clear any interrupt cause that happened while sending - * firmware/initializing card */ + /* + * Clear any interrupt cause that happened while sending + * firmware/initializing card + */ if_cs_write16(card, IF_CS_CARD_INT_CAUSE, IF_CS_BIT_MASK); if_cs_enable_ints(card); /* And finally bring the card up */ if (lbs_start_card(priv) != 0) { - lbs_pr_err("could not activate card\n"); + pr_err("could not activate card\n"); goto out3; } diff --git a/drivers/net/wireless/libertas/if_sdio.c b/drivers/net/wireless/libertas/if_sdio.c index b4de0ca10fe..a7b5cb0c275 100644 --- a/drivers/net/wireless/libertas/if_sdio.c +++ b/drivers/net/wireless/libertas/if_sdio.c @@ -26,6 +26,8 @@ * if_sdio_card_to_host() to pad the data. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/kernel.h> #include <linux/moduleparam.h> #include <linux/slab.h> @@ -409,7 +411,7 @@ static int if_sdio_card_to_host(struct if_sdio_card *card) out: if (ret) - lbs_pr_err("problem fetching packet from firmware\n"); + pr_err("problem fetching packet from firmware\n"); lbs_deb_leave_args(LBS_DEB_SDIO, "ret %d", ret); @@ -446,7 +448,7 @@ static void if_sdio_host_to_card_worker(struct work_struct *work) } if (ret) - lbs_pr_err("error %d sending packet to firmware\n", ret); + pr_err("error %d sending packet to firmware\n", ret); sdio_release_host(card->func); @@ -555,7 +557,7 @@ release: out: if (ret) - lbs_pr_err("failed to load helper firmware\n"); + pr_err("failed to load helper firmware\n"); lbs_deb_leave_args(LBS_DEB_SDIO, "ret %d", ret); return ret; @@ -669,7 +671,7 @@ release: out: if (ret) - lbs_pr_err("failed to load firmware\n"); + pr_err("failed to load firmware\n"); lbs_deb_leave_args(LBS_DEB_SDIO, "ret %d", ret); return ret; @@ -723,7 +725,7 @@ static int if_sdio_prog_firmware(struct if_sdio_card *card) ret = lbs_get_firmware(&card->func->dev, lbs_helper_name, lbs_fw_name, card->model, &fw_table[0], &helper, &mainfw); if (ret) { - lbs_pr_err("failed to find firmware (%d)\n", ret); + pr_err("failed to find firmware (%d)\n", ret); goto out; } @@ -849,7 +851,7 @@ static int if_sdio_enter_deep_sleep(struct lbs_private *priv) ret = __lbs_cmd(priv, CMD_802_11_DEEP_SLEEP, &cmd, sizeof(cmd), lbs_cmd_copyback, (unsigned long) &cmd); if (ret) - lbs_pr_err("DEEP_SLEEP cmd failed\n"); + netdev_err(priv->dev, "DEEP_SLEEP cmd failed\n"); mdelay(200); return ret; @@ -865,7 +867,7 @@ static int if_sdio_exit_deep_sleep(struct lbs_private *priv) sdio_writeb(card->func, HOST_POWER_UP, CONFIGURATION_REG, &ret); if (ret) - lbs_pr_err("sdio_writeb failed!\n"); + netdev_err(priv->dev, "sdio_writeb failed!\n"); sdio_release_host(card->func); lbs_deb_leave_args(LBS_DEB_SDIO, "ret %d", ret); @@ -882,7 +884,7 @@ static int if_sdio_reset_deep_sleep_wakeup(struct lbs_private *priv) sdio_writeb(card->func, 0, CONFIGURATION_REG, &ret); if (ret) - lbs_pr_err("sdio_writeb failed!\n"); + netdev_err(priv->dev, "sdio_writeb failed!\n"); sdio_release_host(card->func); lbs_deb_leave_args(LBS_DEB_SDIO, "ret %d", ret); @@ -961,7 +963,7 @@ static int if_sdio_probe(struct sdio_func *func, } if (i == func->card->num_info) { - lbs_pr_err("unable to identify card model\n"); + pr_err("unable to identify card model\n"); return -ENODEV; } @@ -995,7 +997,7 @@ static int if_sdio_probe(struct sdio_func *func, break; } if (i == ARRAY_SIZE(fw_table)) { - lbs_pr_err("unknown card model 0x%x\n", card->model); + pr_err("unknown card model 0x%x\n", card->model); ret = -ENODEV; goto free; } @@ -1101,7 +1103,7 @@ static int if_sdio_probe(struct sdio_func *func, lbs_deb_sdio("send function INIT command\n"); if (__lbs_cmd(priv, CMD_FUNC_INIT, &cmd, sizeof(cmd), lbs_cmd_copyback, (unsigned long) &cmd)) - lbs_pr_alert("CMD_FUNC_INIT cmd failed\n"); + netdev_alert(priv->dev, "CMD_FUNC_INIT cmd failed\n"); } ret = lbs_start_card(priv); @@ -1163,7 +1165,7 @@ static void if_sdio_remove(struct sdio_func *func) if (__lbs_cmd(card->priv, CMD_FUNC_SHUTDOWN, &cmd, sizeof(cmd), lbs_cmd_copyback, (unsigned long) &cmd)) - lbs_pr_alert("CMD_FUNC_SHUTDOWN cmd failed\n"); + pr_alert("CMD_FUNC_SHUTDOWN cmd failed\n"); } @@ -1202,20 +1204,19 @@ static int if_sdio_suspend(struct device *dev) mmc_pm_flag_t flags = sdio_get_host_pm_caps(func); - lbs_pr_info("%s: suspend: PM flags = 0x%x\n", - sdio_func_id(func), flags); + dev_info(dev, "%s: suspend: PM flags = 0x%x\n", + sdio_func_id(func), flags); /* If we aren't being asked to wake on anything, we should bail out * and let the SD stack power down the card. */ if (card->priv->wol_criteria == EHS_REMOVE_WAKEUP) { - lbs_pr_info("Suspend without wake params -- " - "powering down card."); + dev_info(dev, "Suspend without wake params -- powering down card\n"); return -ENOSYS; } if (!(flags & MMC_PM_KEEP_POWER)) { - lbs_pr_err("%s: cannot remain alive while host is suspended\n", + dev_err(dev, "%s: cannot remain alive while host is suspended\n", sdio_func_id(func)); return -ENOSYS; } @@ -1237,7 +1238,7 @@ static int if_sdio_resume(struct device *dev) struct if_sdio_card *card = sdio_get_drvdata(func); int ret; - lbs_pr_info("%s: resume: we're back\n", sdio_func_id(func)); + dev_info(dev, "%s: resume: we're back\n", sdio_func_id(func)); ret = lbs_resume(card->priv); diff --git a/drivers/net/wireless/libertas/if_spi.c b/drivers/net/wireless/libertas/if_spi.c index f6c2cd665f4..463352c890d 100644 --- a/drivers/net/wireless/libertas/if_spi.c +++ b/drivers/net/wireless/libertas/if_spi.c @@ -17,6 +17,8 @@ * (at your option) any later version. */ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/moduleparam.h> #include <linux/firmware.h> #include <linux/jiffies.h> @@ -57,6 +59,7 @@ struct if_spi_card { /* Handles all SPI communication (except for FW load) */ struct workqueue_struct *workqueue; struct work_struct packet_work; + struct work_struct resume_work; u8 cmd_buffer[IF_SPI_CMD_BUF_SIZE]; @@ -68,6 +71,9 @@ struct if_spi_card { /* Protects cmd_packet_list and data_packet_list */ spinlock_t buffer_lock; + + /* True is card suspended */ + u8 suspended; }; static void free_if_spi_card(struct if_spi_card *card) @@ -139,8 +145,10 @@ static void spu_transaction_finish(struct if_spi_card *card) card->prev_xfer_time = jiffies; } -/* Write out a byte buffer to an SPI register, - * using a series of 16-bit transfers. */ +/* + * Write out a byte buffer to an SPI register, + * using a series of 16-bit transfers. + */ static int spu_write(struct if_spi_card *card, u16 reg, const u8 *buf, int len) { int err = 0; @@ -204,8 +212,10 @@ static int spu_read(struct if_spi_card *card, u16 reg, u8 *buf, int len) struct spi_transfer dummy_trans; struct spi_transfer data_trans; - /* You must take an even number of bytes from the SPU, even if you - * don't care about the last one. */ + /* + * You must take an even number of bytes from the SPU, even if you + * don't care about the last one. + */ BUG_ON(len & 0x1); spu_transaction_init(card); @@ -254,8 +264,10 @@ static inline int spu_read_u16(struct if_spi_card *card, u16 reg, u16 *val) return ret; } -/* Read 32 bits from an SPI register. - * The low 16 bits are read first. */ +/* + * Read 32 bits from an SPI register. + * The low 16 bits are read first. + */ static int spu_read_u32(struct if_spi_card *card, u16 reg, u32 *val) { __le32 buf; @@ -267,13 +279,15 @@ static int spu_read_u32(struct if_spi_card *card, u16 reg, u32 *val) return err; } -/* Keep reading 16 bits from an SPI register until you get the correct result. +/* + * Keep reading 16 bits from an SPI register until you get the correct result. * * If mask = 0, the correct result is any non-zero number. * If mask != 0, the correct result is any number where * number & target_mask == target * - * Returns -ETIMEDOUT if a second passes without the correct result. */ + * Returns -ETIMEDOUT if a second passes without the correct result. + */ static int spu_wait_for_u16(struct if_spi_card *card, u16 reg, u16 target_mask, u16 target) { @@ -293,16 +307,17 @@ static int spu_wait_for_u16(struct if_spi_card *card, u16 reg, } udelay(100); if (time_after(jiffies, timeout)) { - lbs_pr_err("%s: timeout with val=%02x, " - "target_mask=%02x, target=%02x\n", + pr_err("%s: timeout with val=%02x, target_mask=%02x, target=%02x\n", __func__, val, target_mask, target); return -ETIMEDOUT; } } } -/* Read 16 bits from an SPI register until you receive a specific value. - * Returns -ETIMEDOUT if a 4 tries pass without success. */ +/* + * Read 16 bits from an SPI register until you receive a specific value. + * Returns -ETIMEDOUT if a 4 tries pass without success. + */ static int spu_wait_for_u32(struct if_spi_card *card, u32 reg, u32 target) { int err, try; @@ -324,8 +339,10 @@ static int spu_set_interrupt_mode(struct if_spi_card *card, { int err = 0; - /* We can suppress a host interrupt by clearing the appropriate - * bit in the "host interrupt status mask" register */ + /* + * We can suppress a host interrupt by clearing the appropriate + * bit in the "host interrupt status mask" register + */ if (suppress_host_int) { err = spu_write_u16(card, IF_SPI_HOST_INT_STATUS_MASK_REG, 0); if (err) @@ -341,10 +358,12 @@ static int spu_set_interrupt_mode(struct if_spi_card *card, return err; } - /* If auto-interrupts are on, the completion of certain transactions + /* + * If auto-interrupts are on, the completion of certain transactions * will trigger an interrupt automatically. If auto-interrupts * are off, we need to set the "Card Interrupt Cause" register to - * trigger a card interrupt. */ + * trigger a card interrupt. + */ if (auto_int) { err = spu_write_u16(card, IF_SPI_HOST_INT_CTRL_REG, IF_SPI_HICT_TX_DOWNLOAD_OVER_AUTO | @@ -387,7 +406,7 @@ static int spu_set_bus_mode(struct if_spi_card *card, u16 mode) if (err) return err; if ((rval & 0xF) != mode) { - lbs_pr_err("Can't read bus mode register.\n"); + pr_err("Can't read bus mode register\n"); return -EIO; } return 0; @@ -398,8 +417,10 @@ static int spu_init(struct if_spi_card *card, int use_dummy_writes) int err = 0; u32 delay; - /* We have to start up in timed delay mode so that we can safely - * read the Delay Read Register. */ + /* + * We have to start up in timed delay mode so that we can safely + * read the Delay Read Register. + */ card->use_dummy_writes = 0; err = spu_set_bus_mode(card, IF_SPI_BUS_MODE_SPI_CLOCK_PHASE_RISING | @@ -455,8 +476,10 @@ static int if_spi_prog_helper_firmware(struct if_spi_card *card, /* Load helper firmware image */ while (bytes_remaining > 0) { - /* Scratch pad 1 should contain the number of bytes we - * want to download to the firmware */ + /* + * Scratch pad 1 should contain the number of bytes we + * want to download to the firmware + */ err = spu_write_u16(card, IF_SPI_SCRATCH_1_REG, HELPER_FW_LOAD_CHUNK_SZ); if (err) @@ -468,8 +491,10 @@ static int if_spi_prog_helper_firmware(struct if_spi_card *card, if (err) goto out; - /* Feed the data into the command read/write port reg - * in chunks of 64 bytes */ + /* + * Feed the data into the command read/write port reg + * in chunks of 64 bytes + */ memset(temp, 0, sizeof(temp)); memcpy(temp, fw, min(bytes_remaining, HELPER_FW_LOAD_CHUNK_SZ)); @@ -491,9 +516,11 @@ static int if_spi_prog_helper_firmware(struct if_spi_card *card, fw += HELPER_FW_LOAD_CHUNK_SZ; } - /* Once the helper / single stage firmware download is complete, + /* + * Once the helper / single stage firmware download is complete, * write 0 to scratch pad 1 and interrupt the - * bootloader. This completes the helper download. */ + * bootloader. This completes the helper download. + */ err = spu_write_u16(card, IF_SPI_SCRATCH_1_REG, FIRMWARE_DNLD_OK); if (err) goto out; @@ -508,26 +535,30 @@ static int if_spi_prog_helper_firmware(struct if_spi_card *card, out: if (err) - lbs_pr_err("failed to load helper firmware (err=%d)\n", err); + pr_err("failed to load helper firmware (err=%d)\n", err); lbs_deb_leave_args(LBS_DEB_SPI, "err %d", err); return err; } -/* Returns the length of the next packet the firmware expects us to send - * Sets crc_err if the previous transfer had a CRC error. */ +/* + * Returns the length of the next packet the firmware expects us to send. + * Sets crc_err if the previous transfer had a CRC error. + */ static int if_spi_prog_main_firmware_check_len(struct if_spi_card *card, int *crc_err) { u16 len; int err = 0; - /* wait until the host interrupt status register indicates - * that we are ready to download */ + /* + * wait until the host interrupt status register indicates + * that we are ready to download + */ err = spu_wait_for_u16(card, IF_SPI_HOST_INT_STATUS_REG, IF_SPI_HIST_CMD_DOWNLOAD_RDY, IF_SPI_HIST_CMD_DOWNLOAD_RDY); if (err) { - lbs_pr_err("timed out waiting for host_int_status\n"); + pr_err("timed out waiting for host_int_status\n"); return err; } @@ -537,9 +568,8 @@ static int if_spi_prog_main_firmware_check_len(struct if_spi_card *card, return err; if (len > IF_SPI_CMD_BUF_SIZE) { - lbs_pr_err("firmware load device requested a larger " - "tranfer than we are prepared to " - "handle. (len = %d)\n", len); + pr_err("firmware load device requested a larger transfer than we are prepared to handle (len = %d)\n", + len); return -EIO; } if (len & 0x1) { @@ -555,6 +585,7 @@ static int if_spi_prog_main_firmware_check_len(struct if_spi_card *card, static int if_spi_prog_main_firmware(struct if_spi_card *card, const struct firmware *firmware) { + struct lbs_private *priv = card->priv; int len, prev_len; int bytes, crc_err = 0, err = 0; const u8 *fw; @@ -568,8 +599,9 @@ static int if_spi_prog_main_firmware(struct if_spi_card *card, err = spu_wait_for_u16(card, IF_SPI_SCRATCH_1_REG, 0, 0); if (err) { - lbs_pr_err("%s: timed out waiting for initial " - "scratch reg = 0\n", __func__); + netdev_err(priv->dev, + "%s: timed out waiting for initial scratch reg = 0\n", + __func__); goto out; } @@ -583,17 +615,18 @@ static int if_spi_prog_main_firmware(struct if_spi_card *card, goto out; } if (bytes < 0) { - /* If there are no more bytes left, we would normally - * expect to have terminated with len = 0 */ - lbs_pr_err("Firmware load wants more bytes " - "than we have to offer.\n"); + /* + * If there are no more bytes left, we would normally + * expect to have terminated with len = 0 + */ + netdev_err(priv->dev, + "Firmware load wants more bytes than we have to offer.\n"); break; } if (crc_err) { /* Previous transfer failed. */ if (++num_crc_errs > MAX_MAIN_FW_LOAD_CRC_ERR) { - lbs_pr_err("Too many CRC errors encountered " - "in firmware load.\n"); + pr_err("Too many CRC errors encountered in firmware load.\n"); err = -EIO; goto out; } @@ -622,21 +655,20 @@ static int if_spi_prog_main_firmware(struct if_spi_card *card, prev_len = len; } if (bytes > prev_len) { - lbs_pr_err("firmware load wants fewer bytes than " - "we have to offer.\n"); + pr_err("firmware load wants fewer bytes than we have to offer\n"); } /* Confirm firmware download */ err = spu_wait_for_u32(card, IF_SPI_SCRATCH_4_REG, SUCCESSFUL_FW_DOWNLOAD_MAGIC); if (err) { - lbs_pr_err("failed to confirm the firmware download\n"); + pr_err("failed to confirm the firmware download\n"); goto out; } out: if (err) - lbs_pr_err("failed to load firmware (err=%d)\n", err); + pr_err("failed to load firmware (err=%d)\n", err); lbs_deb_leave_args(LBS_DEB_SPI, "err %d", err); return err; } @@ -656,14 +688,18 @@ static int if_spi_c2h_cmd(struct if_spi_card *card) u16 len; u8 i; - /* We need a buffer big enough to handle whatever people send to - * hw_host_to_card */ + /* + * We need a buffer big enough to handle whatever people send to + * hw_host_to_card + */ BUILD_BUG_ON(IF_SPI_CMD_BUF_SIZE < LBS_CMD_BUFFER_SIZE); BUILD_BUG_ON(IF_SPI_CMD_BUF_SIZE < LBS_UPLD_SIZE); - /* It's just annoying if the buffer size isn't a multiple of 4, because - * then we might have len < IF_SPI_CMD_BUF_SIZE but - * ALIGN(len, 4) > IF_SPI_CMD_BUF_SIZE */ + /* + * It's just annoying if the buffer size isn't a multiple of 4, because + * then we might have len < IF_SPI_CMD_BUF_SIZE but + * ALIGN(len, 4) > IF_SPI_CMD_BUF_SIZE + */ BUILD_BUG_ON(IF_SPI_CMD_BUF_SIZE % 4 != 0); lbs_deb_enter(LBS_DEB_SPI); @@ -673,13 +709,13 @@ static int if_spi_c2h_cmd(struct if_spi_card *card) if (err) goto out; if (!len) { - lbs_pr_err("%s: error: card has no data for host\n", + netdev_err(priv->dev, "%s: error: card has no data for host\n", __func__); err = -EINVAL; goto out; } else if (len > IF_SPI_CMD_BUF_SIZE) { - lbs_pr_err("%s: error: response packet too large: " - "%d bytes, but maximum is %d\n", + netdev_err(priv->dev, + "%s: error: response packet too large: %d bytes, but maximum is %d\n", __func__, len, IF_SPI_CMD_BUF_SIZE); err = -EINVAL; goto out; @@ -701,7 +737,7 @@ static int if_spi_c2h_cmd(struct if_spi_card *card) out: if (err) - lbs_pr_err("%s: err=%d\n", __func__, err); + netdev_err(priv->dev, "%s: err=%d\n", __func__, err); lbs_deb_leave(LBS_DEB_SPI); return err; } @@ -709,6 +745,7 @@ out: /* Move data from the card to the host */ static int if_spi_c2h_data(struct if_spi_card *card) { + struct lbs_private *priv = card->priv; struct sk_buff *skb; char *data; u16 len; @@ -721,13 +758,13 @@ static int if_spi_c2h_data(struct if_spi_card *card) if (err) goto out; if (!len) { - lbs_pr_err("%s: error: card has no data for host\n", + netdev_err(priv->dev, "%s: error: card has no data for host\n", __func__); err = -EINVAL; goto out; } else if (len > MRVDRV_ETH_RX_PACKET_BUFFER_SIZE) { - lbs_pr_err("%s: error: card has %d bytes of data, but " - "our maximum skb size is %zu\n", + netdev_err(priv->dev, + "%s: error: card has %d bytes of data, but our maximum skb size is %zu\n", __func__, len, MRVDRV_ETH_RX_PACKET_BUFFER_SIZE); err = -EINVAL; goto out; @@ -759,7 +796,7 @@ free_skb: dev_kfree_skb(skb); out: if (err) - lbs_pr_err("%s: err=%d\n", __func__, err); + netdev_err(priv->dev, "%s: err=%d\n", __func__, err); lbs_deb_leave(LBS_DEB_SPI); return err; } @@ -768,6 +805,7 @@ out: static void if_spi_h2c(struct if_spi_card *card, struct if_spi_packet *packet, int type) { + struct lbs_private *priv = card->priv; int err = 0; u16 int_type, port_reg; @@ -781,7 +819,8 @@ static void if_spi_h2c(struct if_spi_card *card, port_reg = IF_SPI_CMD_RDWRPORT_REG; break; default: - lbs_pr_err("can't transfer buffer of type %d\n", type); + netdev_err(priv->dev, "can't transfer buffer of type %d\n", + type); err = -EINVAL; goto out; } @@ -795,7 +834,7 @@ out: kfree(packet); if (err) - lbs_pr_err("%s: error %d\n", __func__, err); + netdev_err(priv->dev, "%s: error %d\n", __func__, err); } /* Inform the host about a card event */ @@ -819,7 +858,7 @@ static void if_spi_e2h(struct if_spi_card *card) lbs_queue_event(priv, cause & 0xff); out: if (err) - lbs_pr_err("%s: error %d\n", __func__, err); + netdev_err(priv->dev, "%s: error %d\n", __func__, err); } static void if_spi_host_to_card_worker(struct work_struct *work) @@ -829,17 +868,21 @@ static void if_spi_host_to_card_worker(struct work_struct *work) u16 hiStatus; unsigned long flags; struct if_spi_packet *packet; + struct lbs_private *priv; card = container_of(work, struct if_spi_card, packet_work); + priv = card->priv; lbs_deb_enter(LBS_DEB_SPI); - /* Read the host interrupt status register to see what we - * can do. */ + /* + * Read the host interrupt status register to see what we + * can do. + */ err = spu_read_u16(card, IF_SPI_HOST_INT_STATUS_REG, &hiStatus); if (err) { - lbs_pr_err("I/O error\n"); + netdev_err(priv->dev, "I/O error\n"); goto err; } @@ -854,12 +897,15 @@ static void if_spi_host_to_card_worker(struct work_struct *work) goto err; } - /* workaround: in PS mode, the card does not set the Command - * Download Ready bit, but it sets TX Download Ready. */ + /* + * workaround: in PS mode, the card does not set the Command + * Download Ready bit, but it sets TX Download Ready. + */ if (hiStatus & IF_SPI_HIST_CMD_DOWNLOAD_RDY || (card->priv->psstate != PS_STATE_FULL_POWER && (hiStatus & IF_SPI_HIST_TX_DOWNLOAD_RDY))) { - /* This means two things. First of all, + /* + * This means two things. First of all, * if there was a previous command sent, the card has * successfully received it. * Secondly, it is now ready to download another @@ -867,8 +913,7 @@ static void if_spi_host_to_card_worker(struct work_struct *work) */ lbs_host_to_card_done(card->priv); - /* Do we have any command packets from the host to - * send? */ + /* Do we have any command packets from the host to send? */ packet = NULL; spin_lock_irqsave(&card->buffer_lock, flags); if (!list_empty(&card->cmd_packet_list)) { @@ -882,8 +927,7 @@ static void if_spi_host_to_card_worker(struct work_struct *work) if_spi_h2c(card, packet, MVMS_CMD); } if (hiStatus & IF_SPI_HIST_TX_DOWNLOAD_RDY) { - /* Do we have any data packets from the host to - * send? */ + /* Do we have any data packets from the host to send? */ packet = NULL; spin_lock_irqsave(&card->buffer_lock, flags); if (!list_empty(&card->data_packet_list)) { @@ -901,7 +945,7 @@ static void if_spi_host_to_card_worker(struct work_struct *work) err: if (err) - lbs_pr_err("%s: got error %d\n", __func__, err); + netdev_err(priv->dev, "%s: got error %d\n", __func__, err); lbs_deb_leave(LBS_DEB_SPI); } @@ -910,7 +954,8 @@ err: * Host to Card * * Called from Libertas to transfer some data to the WLAN device - * We can't sleep here. */ + * We can't sleep here. + */ static int if_spi_host_to_card(struct lbs_private *priv, u8 type, u8 *buf, u16 nb) { @@ -923,7 +968,8 @@ static int if_spi_host_to_card(struct lbs_private *priv, lbs_deb_enter_args(LBS_DEB_SPI, "type %d, bytes %d", type, nb); if (nb == 0) { - lbs_pr_err("%s: invalid size requested: %d\n", __func__, nb); + netdev_err(priv->dev, "%s: invalid size requested: %d\n", + __func__, nb); err = -EINVAL; goto out; } @@ -951,7 +997,8 @@ static int if_spi_host_to_card(struct lbs_private *priv, spin_unlock_irqrestore(&card->buffer_lock, flags); break; default: - lbs_pr_err("can't transfer buffer of type %d", type); + netdev_err(priv->dev, "can't transfer buffer of type %d\n", + type); err = -EINVAL; break; } @@ -984,6 +1031,7 @@ static irqreturn_t if_spi_host_interrupt(int irq, void *dev_id) static int if_spi_init_card(struct if_spi_card *card) { + struct lbs_private *priv = card->priv; struct spi_device *spi = card->spi; int err, i; u32 scratch; @@ -1012,8 +1060,8 @@ static int if_spi_init_card(struct if_spi_card *card) break; } if (i == ARRAY_SIZE(fw_table)) { - lbs_pr_err("Unsupported chip_id: 0x%02x\n", - card->card_id); + netdev_err(priv->dev, "Unsupported chip_id: 0x%02x\n", + card->card_id); err = -ENODEV; goto out; } @@ -1022,7 +1070,8 @@ static int if_spi_init_card(struct if_spi_card *card) card->card_id, &fw_table[0], &helper, &mainfw); if (err) { - lbs_pr_err("failed to find firmware (%d)\n", err); + netdev_err(priv->dev, "failed to find firmware (%d)\n", + err); goto out; } @@ -1057,6 +1106,28 @@ out: return err; } +static void if_spi_resume_worker(struct work_struct *work) +{ + struct if_spi_card *card; + + card = container_of(work, struct if_spi_card, resume_work); + + if (card->suspended) { + if (card->pdata->setup) + card->pdata->setup(card->spi); + + /* Init card ... */ + if_spi_init_card(card); + + enable_irq(card->spi->irq); + + /* And resume it ... */ + lbs_resume(card->priv); + + card->suspended = 0; + } +} + static int __devinit if_spi_probe(struct spi_device *spi) { struct if_spi_card *card; @@ -1099,14 +1170,17 @@ static int __devinit if_spi_probe(struct spi_device *spi) if (err) goto free_card; - /* Register our card with libertas. - * This will call alloc_etherdev */ + /* + * Register our card with libertas. + * This will call alloc_etherdev. + */ priv = lbs_add_card(card, &spi->dev); if (!priv) { err = -ENOMEM; goto free_card; } card->priv = priv; + priv->setup_fw_on_resume = 1; priv->card = card; priv->hw_host_to_card = if_spi_host_to_card; priv->enter_deep_sleep = NULL; @@ -1117,17 +1191,20 @@ static int __devinit if_spi_probe(struct spi_device *spi) /* Initialize interrupt handling stuff. */ card->workqueue = create_workqueue("libertas_spi"); INIT_WORK(&card->packet_work, if_spi_host_to_card_worker); + INIT_WORK(&card->resume_work, if_spi_resume_worker); err = request_irq(spi->irq, if_spi_host_interrupt, IRQF_TRIGGER_FALLING, "libertas_spi", card); if (err) { - lbs_pr_err("can't get host irq line-- request_irq failed\n"); + pr_err("can't get host irq line-- request_irq failed\n"); goto terminate_workqueue; } - /* Start the card. + /* + * Start the card. * This will call register_netdev, and we'll start - * getting interrupts... */ + * getting interrupts... + */ err = lbs_start_card(priv); if (err) goto release_irq; @@ -1161,6 +1238,8 @@ static int __devexit libertas_spi_remove(struct spi_device *spi) lbs_deb_spi("libertas_spi_remove\n"); lbs_deb_enter(LBS_DEB_SPI); + cancel_work_sync(&card->resume_work); + lbs_stop_card(priv); lbs_remove_card(priv); /* will call free_netdev */ @@ -1174,6 +1253,40 @@ static int __devexit libertas_spi_remove(struct spi_device *spi) return 0; } +static int if_spi_suspend(struct device *dev) +{ + struct spi_device *spi = to_spi_device(dev); + struct if_spi_card *card = spi_get_drvdata(spi); + + if (!card->suspended) { + lbs_suspend(card->priv); + flush_workqueue(card->workqueue); + disable_irq(spi->irq); + + if (card->pdata->teardown) + card->pdata->teardown(spi); + card->suspended = 1; + } + + return 0; +} + +static int if_spi_resume(struct device *dev) +{ + struct spi_device *spi = to_spi_device(dev); + struct if_spi_card *card = spi_get_drvdata(spi); + + /* Schedule delayed work */ + schedule_work(&card->resume_work); + + return 0; +} + +static const struct dev_pm_ops if_spi_pm_ops = { + .suspend = if_spi_suspend, + .resume = if_spi_resume, +}; + static struct spi_driver libertas_spi_driver = { .probe = if_spi_probe, .remove = __devexit_p(libertas_spi_remove), @@ -1181,6 +1294,7 @@ static struct spi_driver libertas_spi_driver = { .name = "libertas_spi", .bus = &spi_bus_type, .owner = THIS_MODULE, + .pm = &if_spi_pm_ops, }, }; diff --git a/drivers/net/wireless/libertas/if_spi.h b/drivers/net/wireless/libertas/if_spi.h index d2ac1dcd7e2..e450e31fd11 100644 --- a/drivers/net/wireless/libertas/if_spi.h +++ b/drivers/net/wireless/libertas/if_spi.h @@ -86,34 +86,34 @@ #define IF_SPI_DEVICEID_CTRL_REG_TO_CARD_REV(dc) (dc & 0x000000ff) /***************** IF_SPI_HOST_INT_CTRL_REG *****************/ -/** Host Interrupt Control bit : Wake up */ +/* Host Interrupt Control bit : Wake up */ #define IF_SPI_HICT_WAKE_UP (1<<0) -/** Host Interrupt Control bit : WLAN ready */ +/* Host Interrupt Control bit : WLAN ready */ #define IF_SPI_HICT_WLAN_READY (1<<1) /*#define IF_SPI_HICT_FIFO_FIRST_HALF_EMPTY (1<<2) */ /*#define IF_SPI_HICT_FIFO_SECOND_HALF_EMPTY (1<<3) */ /*#define IF_SPI_HICT_IRQSRC_WLAN (1<<4) */ -/** Host Interrupt Control bit : Tx auto download */ +/* Host Interrupt Control bit : Tx auto download */ #define IF_SPI_HICT_TX_DOWNLOAD_OVER_AUTO (1<<5) -/** Host Interrupt Control bit : Rx auto upload */ +/* Host Interrupt Control bit : Rx auto upload */ #define IF_SPI_HICT_RX_UPLOAD_OVER_AUTO (1<<6) -/** Host Interrupt Control bit : Command auto download */ +/* Host Interrupt Control bit : Command auto download */ #define IF_SPI_HICT_CMD_DOWNLOAD_OVER_AUTO (1<<7) -/** Host Interrupt Control bit : Command auto upload */ +/* Host Interrupt Control bit : Command auto upload */ #define IF_SPI_HICT_CMD_UPLOAD_OVER_AUTO (1<<8) /***************** IF_SPI_CARD_INT_CAUSE_REG *****************/ -/** Card Interrupt Case bit : Tx download over */ +/* Card Interrupt Case bit : Tx download over */ #define IF_SPI_CIC_TX_DOWNLOAD_OVER (1<<0) -/** Card Interrupt Case bit : Rx upload over */ +/* Card Interrupt Case bit : Rx upload over */ #define IF_SPI_CIC_RX_UPLOAD_OVER (1<<1) -/** Card Interrupt Case bit : Command download over */ +/* Card Interrupt Case bit : Command download over */ #define IF_SPI_CIC_CMD_DOWNLOAD_OVER (1<<2) -/** Card Interrupt Case bit : Host event */ +/* Card Interrupt Case bit : Host event */ #define IF_SPI_CIC_HOST_EVENT (1<<3) -/** Card Interrupt Case bit : Command upload over */ +/* Card Interrupt Case bit : Command upload over */ #define IF_SPI_CIC_CMD_UPLOAD_OVER (1<<4) -/** Card Interrupt Case bit : Power down */ +/* Card Interrupt Case bit : Power down */ #define IF_SPI_CIC_POWER_DOWN (1<<5) /***************** IF_SPI_CARD_INT_STATUS_REG *****************/ @@ -138,51 +138,51 @@ #define IF_SPI_HICU_CMD_RD_FIFO_UNDERFLOW (1<<10) /***************** IF_SPI_HOST_INT_STATUS_REG *****************/ -/** Host Interrupt Status bit : Tx download ready */ +/* Host Interrupt Status bit : Tx download ready */ #define IF_SPI_HIST_TX_DOWNLOAD_RDY (1<<0) -/** Host Interrupt Status bit : Rx upload ready */ +/* Host Interrupt Status bit : Rx upload ready */ #define IF_SPI_HIST_RX_UPLOAD_RDY (1<<1) -/** Host Interrupt Status bit : Command download ready */ +/* Host Interrupt Status bit : Command download ready */ #define IF_SPI_HIST_CMD_DOWNLOAD_RDY (1<<2) -/** Host Interrupt Status bit : Card event */ +/* Host Interrupt Status bit : Card event */ #define IF_SPI_HIST_CARD_EVENT (1<<3) -/** Host Interrupt Status bit : Command upload ready */ +/* Host Interrupt Status bit : Command upload ready */ #define IF_SPI_HIST_CMD_UPLOAD_RDY (1<<4) -/** Host Interrupt Status bit : I/O write FIFO overflow */ +/* Host Interrupt Status bit : I/O write FIFO overflow */ #define IF_SPI_HIST_IO_WR_FIFO_OVERFLOW (1<<5) -/** Host Interrupt Status bit : I/O read FIFO underflow */ +/* Host Interrupt Status bit : I/O read FIFO underflow */ #define IF_SPI_HIST_IO_RD_FIFO_UNDRFLOW (1<<6) -/** Host Interrupt Status bit : Data write FIFO overflow */ +/* Host Interrupt Status bit : Data write FIFO overflow */ #define IF_SPI_HIST_DATA_WR_FIFO_OVERFLOW (1<<7) -/** Host Interrupt Status bit : Data read FIFO underflow */ +/* Host Interrupt Status bit : Data read FIFO underflow */ #define IF_SPI_HIST_DATA_RD_FIFO_UNDERFLOW (1<<8) -/** Host Interrupt Status bit : Command write FIFO overflow */ +/* Host Interrupt Status bit : Command write FIFO overflow */ #define IF_SPI_HIST_CMD_WR_FIFO_OVERFLOW (1<<9) -/** Host Interrupt Status bit : Command read FIFO underflow */ +/* Host Interrupt Status bit : Command read FIFO underflow */ #define IF_SPI_HIST_CMD_RD_FIFO_UNDERFLOW (1<<10) /***************** IF_SPI_HOST_INT_STATUS_MASK_REG *****************/ -/** Host Interrupt Status Mask bit : Tx download ready */ +/* Host Interrupt Status Mask bit : Tx download ready */ #define IF_SPI_HISM_TX_DOWNLOAD_RDY (1<<0) -/** Host Interrupt Status Mask bit : Rx upload ready */ +/* Host Interrupt Status Mask bit : Rx upload ready */ #define IF_SPI_HISM_RX_UPLOAD_RDY (1<<1) -/** Host Interrupt Status Mask bit : Command download ready */ +/* Host Interrupt Status Mask bit : Command download ready */ #define IF_SPI_HISM_CMD_DOWNLOAD_RDY (1<<2) -/** Host Interrupt Status Mask bit : Card event */ +/* Host Interrupt Status Mask bit : Card event */ #define IF_SPI_HISM_CARDEVENT (1<<3) -/** Host Interrupt Status Mask bit : Command upload ready */ +/* Host Interrupt Status Mask bit : Command upload ready */ #define IF_SPI_HISM_CMD_UPLOAD_RDY (1<<4) -/** Host Interrupt Status Mask bit : I/O write FIFO overflow */ +/* Host Interrupt Status Mask bit : I/O write FIFO overflow */ #define IF_SPI_HISM_IO_WR_FIFO_OVERFLOW (1<<5) -/** Host Interrupt Status Mask bit : I/O read FIFO underflow */ +/* Host Interrupt Status Mask bit : I/O read FIFO underflow */ #define IF_SPI_HISM_IO_RD_FIFO_UNDERFLOW (1<<6) -/** Host Interrupt Status Mask bit : Data write FIFO overflow */ +/* Host Interrupt Status Mask bit : Data write FIFO overflow */ #define IF_SPI_HISM_DATA_WR_FIFO_OVERFLOW (1<<7) -/** Host Interrupt Status Mask bit : Data write FIFO underflow */ +/* Host Interrupt Status Mask bit : Data write FIFO underflow */ #define IF_SPI_HISM_DATA_RD_FIFO_UNDERFLOW (1<<8) -/** Host Interrupt Status Mask bit : Command write FIFO overflow */ +/* Host Interrupt Status Mask bit : Command write FIFO overflow */ #define IF_SPI_HISM_CMD_WR_FIFO_OVERFLOW (1<<9) -/** Host Interrupt Status Mask bit : Command write FIFO underflow */ +/* Host Interrupt Status Mask bit : Command write FIFO underflow */ #define IF_SPI_HISM_CMD_RD_FIFO_UNDERFLOW (1<<10) /***************** IF_SPI_SPU_BUS_MODE_REG *****************/ diff --git a/drivers/net/wireless/libertas/if_usb.c b/drivers/net/wireless/libertas/if_usb.c index 6524c70363d..b5acc393a65 100644 --- a/drivers/net/wireless/libertas/if_usb.c +++ b/drivers/net/wireless/libertas/if_usb.c @@ -1,6 +1,9 @@ -/** - * This file contains functions used in USB interface module. - */ +/* + * This file contains functions used in USB interface module. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/delay.h> #include <linux/moduleparam.h> #include <linux/firmware.h> @@ -66,7 +69,7 @@ static int if_usb_reset_device(struct if_usb_card *cardp); /* sysfs hooks */ -/** +/* * Set function to write firmware to device's persistent memory */ static ssize_t if_usb_firmware_set(struct device *dev, @@ -85,7 +88,7 @@ static ssize_t if_usb_firmware_set(struct device *dev, return ret; } -/** +/* * lbs_flash_fw attribute to be exported per ethX interface through sysfs * (/sys/class/net/ethX/lbs_flash_fw). Use this like so to write firmware to * the device's persistent memory: @@ -94,7 +97,14 @@ static ssize_t if_usb_firmware_set(struct device *dev, static DEVICE_ATTR(lbs_flash_fw, 0200, NULL, if_usb_firmware_set); /** - * Set function to write firmware to device's persistent memory + * if_usb_boot2_set - write firmware to device's persistent memory + * + * @dev: target device + * @attr: device attributes + * @buf: firmware buffer to write + * @count: number of bytes to write + * + * returns: number of bytes written or negative error code */ static ssize_t if_usb_boot2_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -112,7 +122,7 @@ static ssize_t if_usb_boot2_set(struct device *dev, return ret; } -/** +/* * lbs_flash_boot2 attribute to be exported per ethX interface through sysfs * (/sys/class/net/ethX/lbs_flash_boot2). Use this like so to write firmware * to the device's persistent memory: @@ -121,9 +131,10 @@ static ssize_t if_usb_boot2_set(struct device *dev, static DEVICE_ATTR(lbs_flash_boot2, 0200, NULL, if_usb_boot2_set); /** - * @brief call back function to handle the status of the URB - * @param urb pointer to urb structure - * @return N/A + * if_usb_write_bulk_callback - callback function to handle the status + * of the URB + * @urb: pointer to &urb structure + * returns: N/A */ static void if_usb_write_bulk_callback(struct urb *urb) { @@ -145,14 +156,14 @@ static void if_usb_write_bulk_callback(struct urb *urb) lbs_host_to_card_done(priv); } else { /* print the failure status number for debug */ - lbs_pr_info("URB in failure status: %d\n", urb->status); + pr_info("URB in failure status: %d\n", urb->status); } } /** - * @brief free tx/rx urb, skb and rx buffer - * @param cardp pointer if_usb_card - * @return N/A + * if_usb_free - free tx/rx urb, skb and rx buffer + * @cardp: pointer to &if_usb_card + * returns: N/A */ static void if_usb_free(struct if_usb_card *cardp) { @@ -195,7 +206,7 @@ static void if_usb_setup_firmware(struct lbs_private *priv) wake_method.hdr.size = cpu_to_le16(sizeof(wake_method)); wake_method.action = cpu_to_le16(CMD_ACT_GET); if (lbs_cmd_with_response(priv, CMD_802_11_FW_WAKE_METHOD, &wake_method)) { - lbs_pr_info("Firmware does not seem to support PS mode\n"); + netdev_info(priv->dev, "Firmware does not seem to support PS mode\n"); priv->fwcapinfo &= ~FW_CAPINFO_PS; } else { if (le16_to_cpu(wake_method.method) == CMD_WAKE_METHOD_COMMAND_INT) { @@ -204,7 +215,8 @@ static void if_usb_setup_firmware(struct lbs_private *priv) /* The versions which boot up this way don't seem to work even if we set it to the command interrupt */ priv->fwcapinfo &= ~FW_CAPINFO_PS; - lbs_pr_info("Firmware doesn't wake via command interrupt; disabling PS mode\n"); + netdev_info(priv->dev, + "Firmware doesn't wake via command interrupt; disabling PS mode\n"); } } } @@ -216,7 +228,7 @@ static void if_usb_fw_timeo(unsigned long priv) if (cardp->fwdnldover) { lbs_deb_usb("Download complete, no event. Assuming success\n"); } else { - lbs_pr_err("Download timed out\n"); + pr_err("Download timed out\n"); cardp->surprise_removed = 1; } wake_up(&cardp->fw_wq); @@ -231,10 +243,10 @@ static void if_usb_reset_olpc_card(struct lbs_private *priv) #endif /** - * @brief sets the configuration values - * @param ifnum interface number - * @param id pointer to usb_device_id - * @return 0 on success, error code on failure + * if_usb_probe - sets the configuration values + * @intf: &usb_interface pointer + * @id: pointer to usb_device_id + * returns: 0 on success, error code on failure */ static int if_usb_probe(struct usb_interface *intf, const struct usb_device_id *id) @@ -250,7 +262,7 @@ static int if_usb_probe(struct usb_interface *intf, cardp = kzalloc(sizeof(struct if_usb_card), GFP_KERNEL); if (!cardp) { - lbs_pr_err("Out of memory allocating private data.\n"); + pr_err("Out of memory allocating private data\n"); goto error; } @@ -340,10 +352,12 @@ static int if_usb_probe(struct usb_interface *intf, usb_set_intfdata(intf, cardp); if (device_create_file(&priv->dev->dev, &dev_attr_lbs_flash_fw)) - lbs_pr_err("cannot register lbs_flash_fw attribute\n"); + netdev_err(priv->dev, + "cannot register lbs_flash_fw attribute\n"); if (device_create_file(&priv->dev->dev, &dev_attr_lbs_flash_boot2)) - lbs_pr_err("cannot register lbs_flash_boot2 attribute\n"); + netdev_err(priv->dev, + "cannot register lbs_flash_boot2 attribute\n"); /* * EHS_REMOVE_WAKEUP is not supported on all versions of the firmware. @@ -366,9 +380,9 @@ error: } /** - * @brief free resource and cleanup - * @param intf USB interface structure - * @return N/A + * if_usb_disconnect - free resource and cleanup + * @intf: USB interface structure + * returns: N/A */ static void if_usb_disconnect(struct usb_interface *intf) { @@ -398,9 +412,9 @@ static void if_usb_disconnect(struct usb_interface *intf) } /** - * @brief This function download FW - * @param priv pointer to struct lbs_private - * @return 0 + * if_usb_send_fw_pkt - download FW + * @cardp: pointer to &struct if_usb_card + * returns: 0 */ static int if_usb_send_fw_pkt(struct if_usb_card *cardp) { @@ -486,11 +500,11 @@ static int if_usb_reset_device(struct if_usb_card *cardp) } /** - * @brief This function transfer the data to the device. - * @param priv pointer to struct lbs_private - * @param payload pointer to payload data - * @param nb data length - * @return 0 or -1 + * usb_tx_block - transfer the data to the device + * @cardp: pointer to &struct if_usb_card + * @payload: pointer to payload data + * @nb: data length + * returns: 0 for success or negative error code */ static int usb_tx_block(struct if_usb_card *cardp, uint8_t *payload, uint16_t nb) { @@ -528,7 +542,7 @@ static int __if_usb_submit_rx_urb(struct if_usb_card *cardp, int ret = -1; if (!(skb = dev_alloc_skb(MRVDRV_ETH_RX_PACKET_BUFFER_SIZE))) { - lbs_pr_err("No free skb\n"); + pr_err("No free skb\n"); goto rx_ret; } @@ -587,7 +601,7 @@ static void if_usb_receive_fwload(struct urb *urb) if (tmp[0] == cpu_to_le32(CMD_TYPE_INDICATION) && tmp[1] == cpu_to_le32(MACREG_INT_CODE_FIRMWARE_READY)) { - lbs_pr_info("Firmware ready event received\n"); + pr_info("Firmware ready event received\n"); wake_up(&cardp->fw_wq); } else { lbs_deb_usb("Waiting for confirmation; got %x %x\n", @@ -614,20 +628,20 @@ static void if_usb_receive_fwload(struct urb *urb) bootcmdresp.magic == cpu_to_le32(CMD_TYPE_DATA) || bootcmdresp.magic == cpu_to_le32(CMD_TYPE_INDICATION)) { if (!cardp->bootcmdresp) - lbs_pr_info("Firmware already seems alive; resetting\n"); + pr_info("Firmware already seems alive; resetting\n"); cardp->bootcmdresp = -1; } else { - lbs_pr_info("boot cmd response wrong magic number (0x%x)\n", + pr_info("boot cmd response wrong magic number (0x%x)\n", le32_to_cpu(bootcmdresp.magic)); } } else if ((bootcmdresp.cmd != BOOT_CMD_FW_BY_USB) && (bootcmdresp.cmd != BOOT_CMD_UPDATE_FW) && (bootcmdresp.cmd != BOOT_CMD_UPDATE_BOOT2)) { - lbs_pr_info("boot cmd response cmd_tag error (%d)\n", - bootcmdresp.cmd); + pr_info("boot cmd response cmd_tag error (%d)\n", + bootcmdresp.cmd); } else if (bootcmdresp.result != BOOT_CMD_RESP_OK) { - lbs_pr_info("boot cmd response result error (%d)\n", - bootcmdresp.result); + pr_info("boot cmd response result error (%d)\n", + bootcmdresp.result); } else { cardp->bootcmdresp = 1; lbs_deb_usbd(&cardp->udev->dev, @@ -727,11 +741,11 @@ static inline void process_cmdrequest(int recvlength, uint8_t *recvbuff, } /** - * @brief This function reads of the packet into the upload buff, - * wake up the main thread and initialise the Rx callack. + * if_usb_receive - read the packet into the upload buffer, + * wake up the main thread and initialise the Rx callack * - * @param urb pointer to struct urb - * @return N/A + * @urb: pointer to &struct urb + * returns: N/A */ static void if_usb_receive(struct urb *urb) { @@ -802,12 +816,12 @@ rx_exit: } /** - * @brief This function downloads data to FW - * @param priv pointer to struct lbs_private structure - * @param type type of data - * @param buf pointer to data buffer - * @param len number of bytes - * @return 0 or -1 + * if_usb_host_to_card - downloads data to FW + * @priv: pointer to &struct lbs_private structure + * @type: type of data + * @payload: pointer to data buffer + * @nb: number of bytes + * returns: 0 for success or negative error code */ static int if_usb_host_to_card(struct lbs_private *priv, uint8_t type, uint8_t *payload, uint16_t nb) @@ -831,10 +845,11 @@ static int if_usb_host_to_card(struct lbs_private *priv, uint8_t type, } /** - * @brief This function issues Boot command to the Boot2 code - * @param ivalue 1:Boot from FW by USB-Download - * 2:Boot from FW in EEPROM - * @return 0 + * if_usb_issue_boot_command - issues Boot command to the Boot2 code + * @cardp: pointer to &if_usb_card + * @ivalue: 1:Boot from FW by USB-Download + * 2:Boot from FW in EEPROM + * returns: 0 for success or negative error code */ static int if_usb_issue_boot_command(struct if_usb_card *cardp, int ivalue) { @@ -853,11 +868,11 @@ static int if_usb_issue_boot_command(struct if_usb_card *cardp, int ivalue) /** - * @brief This function checks the validity of Boot2/FW image. + * check_fwfile_format - check the validity of Boot2/FW image * - * @param data pointer to image - * len image length - * @return 0 or -1 + * @data: pointer to image + * @totlen: image length + * returns: 0 (good) or 1 (failure) */ static int check_fwfile_format(const uint8_t *data, uint32_t totlen) { @@ -892,7 +907,7 @@ static int check_fwfile_format(const uint8_t *data, uint32_t totlen) } while (!exit); if (ret) - lbs_pr_err("firmware file format check FAIL\n"); + pr_err("firmware file format check FAIL\n"); else lbs_deb_fw("firmware file format check PASS\n"); @@ -901,13 +916,13 @@ static int check_fwfile_format(const uint8_t *data, uint32_t totlen) /** -* @brief This function programs the firmware subject to cmd +* if_usb_prog_firmware - programs the firmware subject to cmd * -* @param cardp the if_usb_card descriptor -* fwname firmware or boot2 image file name -* cmd either BOOT_CMD_FW_BY_USB, BOOT_CMD_UPDATE_FW, -* or BOOT_CMD_UPDATE_BOOT2. -* @return 0 or error code +* @cardp: the if_usb_card descriptor +* @fwname: firmware or boot2 image file name +* @cmd: either BOOT_CMD_FW_BY_USB, BOOT_CMD_UPDATE_FW, +* or BOOT_CMD_UPDATE_BOOT2. +* returns: 0 or error code */ static int if_usb_prog_firmware(struct if_usb_card *cardp, const char *fwname, int cmd) @@ -989,7 +1004,7 @@ static int __if_usb_prog_firmware(struct if_usb_card *cardp, ret = get_fw(cardp, fwname); if (ret) { - lbs_pr_err("failed to find firmware (%d)\n", ret); + pr_err("failed to find firmware (%d)\n", ret); goto done; } @@ -1064,13 +1079,13 @@ restart: usb_kill_urb(cardp->rx_urb); if (!cardp->fwdnldover) { - lbs_pr_info("failed to load fw, resetting device!\n"); + pr_info("failed to load fw, resetting device!\n"); if (--reset_count >= 0) { if_usb_reset_device(cardp); goto restart; } - lbs_pr_info("FW download failure, time = %d ms\n", i * 100); + pr_info("FW download failure, time = %d ms\n", i * 100); ret = -EIO; goto release_fw; } diff --git a/drivers/net/wireless/libertas/if_usb.h b/drivers/net/wireless/libertas/if_usb.h index d819e7e3c9a..6e42eac331d 100644 --- a/drivers/net/wireless/libertas/if_usb.h +++ b/drivers/net/wireless/libertas/if_usb.h @@ -6,9 +6,9 @@ struct lbs_private; -/** - * This file contains definition for USB interface. - */ +/* + * This file contains definition for USB interface. + */ #define CMD_TYPE_REQUEST 0xF00DFACE #define CMD_TYPE_DATA 0xBEADC0DE #define CMD_TYPE_INDICATION 0xBEEFFACE @@ -40,7 +40,7 @@ struct bootcmdresp uint8_t pad[2]; }; -/** USB card description structure*/ +/* USB card description structure*/ struct if_usb_card { struct usb_device *udev; uint32_t model; /* MODEL_* */ @@ -77,7 +77,7 @@ struct if_usb_card { __le16 boot2_version; }; -/** fwheader */ +/* fwheader */ struct fwheader { __le32 dnldcmd; __le32 baseaddr; @@ -86,14 +86,14 @@ struct fwheader { }; #define FW_MAX_DATA_BLK_SIZE 600 -/** FWData */ +/* FWData */ struct fwdata { struct fwheader hdr; __le32 seqnum; uint8_t data[0]; }; -/** fwsyncheader */ +/* fwsyncheader */ struct fwsyncheader { __le32 cmd; __le32 seqnum; diff --git a/drivers/net/wireless/libertas/main.c b/drivers/net/wireless/libertas/main.c index ca8149cd5bd..8c40949cb07 100644 --- a/drivers/net/wireless/libertas/main.c +++ b/drivers/net/wireless/libertas/main.c @@ -1,8 +1,10 @@ -/** - * This file contains the major functions in WLAN - * driver. It includes init, exit, open, close and main - * thread etc.. - */ +/* + * This file contains the major functions in WLAN + * driver. It includes init, exit, open, close and main + * thread etc.. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt #include <linux/moduleparam.h> #include <linux/delay.h> @@ -34,19 +36,25 @@ unsigned int lbs_debug; EXPORT_SYMBOL_GPL(lbs_debug); module_param_named(libertas_debug, lbs_debug, int, 0644); +unsigned int lbs_disablemesh; +EXPORT_SYMBOL_GPL(lbs_disablemesh); +module_param_named(libertas_disablemesh, lbs_disablemesh, int, 0644); -/* This global structure is used to send the confirm_sleep command as - * fast as possible down to the firmware. */ + +/* + * This global structure is used to send the confirm_sleep command as + * fast as possible down to the firmware. + */ struct cmd_confirm_sleep confirm_sleep; -/** +/* * the table to keep region code */ u16 lbs_region_code_to_index[MRVDRV_MAX_REGION_CODE] = { 0x10, 0x20, 0x30, 0x31, 0x32, 0x40 }; -/** +/* * FW rate table. FW refers to rates by their index in this table, not by the * rate value itself. Values of 0x00 are * reserved positions. @@ -57,10 +65,10 @@ static u8 fw_data_rates[MAX_RATES] = }; /** - * @brief use index to get the data rate + * lbs_fw_index_to_data_rate - use index to get the data rate * - * @param idx The index of data rate - * @return data rate or 0 + * @idx: The index of data rate + * returns: data rate or 0 */ u32 lbs_fw_index_to_data_rate(u8 idx) { @@ -70,10 +78,10 @@ u32 lbs_fw_index_to_data_rate(u8 idx) } /** - * @brief use rate to get the index + * lbs_data_rate_to_fw_index - use rate to get the index * - * @param rate data rate - * @return index or 0 + * @rate: data rate + * returns: index or 0 */ u8 lbs_data_rate_to_fw_index(u32 rate) { @@ -91,10 +99,10 @@ u8 lbs_data_rate_to_fw_index(u32 rate) /** - * @brief This function opens the ethX interface + * lbs_dev_open - open the ethX interface * - * @param dev A pointer to net_device structure - * @return 0 or -EBUSY if monitor mode active + * @dev: A pointer to &net_device structure + * returns: 0 or -EBUSY if monitor mode active */ static int lbs_dev_open(struct net_device *dev) { @@ -120,10 +128,10 @@ static int lbs_dev_open(struct net_device *dev) } /** - * @brief This function closes the ethX interface + * lbs_eth_stop - close the ethX interface * - * @param dev A pointer to net_device structure - * @return 0 + * @dev: A pointer to &net_device structure + * returns: 0 */ static int lbs_eth_stop(struct net_device *dev) { @@ -147,28 +155,6 @@ static int lbs_eth_stop(struct net_device *dev) return 0; } -static void lbs_tx_timeout(struct net_device *dev) -{ - struct lbs_private *priv = dev->ml_priv; - - lbs_deb_enter(LBS_DEB_TX); - - lbs_pr_err("tx watch dog timeout\n"); - - dev->trans_start = jiffies; /* prevent tx timeout */ - - if (priv->currenttxskb) - lbs_send_tx_feedback(priv, 0); - - /* XX: Shouldn't we also call into the hw-specific driver - to kick it somehow? */ - lbs_host_to_card_done(priv); - - /* FIXME: reset the card */ - - lbs_deb_leave(LBS_DEB_TX); -} - void lbs_host_to_card_done(struct lbs_private *priv) { unsigned long flags; @@ -336,12 +322,12 @@ void lbs_set_multicast_list(struct net_device *dev) } /** - * @brief This function handles the major jobs in the LBS driver. + * lbs_thread - handles the major jobs in the LBS driver. * It handles all events generated by firmware, RX data received * from firmware and TX data sent from kernel. * - * @param data A pointer to lbs_thread structure - * @return 0 + * @data: A pointer to &lbs_thread structure + * returns: 0 */ static int lbs_thread(void *data) { @@ -462,8 +448,8 @@ static int lbs_thread(void *data) if (priv->cmd_timed_out && priv->cur_cmd) { struct cmd_ctrl_node *cmdnode = priv->cur_cmd; - lbs_pr_info("Timeout submitting command 0x%04x\n", - le16_to_cpu(cmdnode->cmdbuf->command)); + netdev_info(dev, "Timeout submitting command 0x%04x\n", + le16_to_cpu(cmdnode->cmdbuf->command)); lbs_complete_command(priv, cmdnode, -ETIMEDOUT); if (priv->reset_card) priv->reset_card(priv); @@ -490,8 +476,8 @@ static int lbs_thread(void *data) * after firmware fixes it */ priv->psstate = PS_STATE_AWAKE; - lbs_pr_alert("ignore PS_SleepConfirm in " - "non-connected state\n"); + netdev_alert(dev, + "ignore PS_SleepConfirm in non-connected state\n"); } } @@ -540,11 +526,11 @@ static int lbs_thread(void *data) } /** - * @brief This function gets the HW spec from the firmware and sets - * some basic parameters. + * lbs_setup_firmware - gets the HW spec from the firmware and sets + * some basic parameters * - * @param priv A pointer to struct lbs_private structure - * @return 0 or -1 + * @priv: A pointer to &struct lbs_private structure + * returns: 0 or -1 */ static int lbs_setup_firmware(struct lbs_private *priv) { @@ -585,7 +571,8 @@ int lbs_suspend(struct lbs_private *priv) if (priv->is_deep_sleep) { ret = lbs_set_deep_sleep(priv, 0); if (ret) { - lbs_pr_err("deep sleep cancellation failed: %d\n", ret); + netdev_err(priv->dev, + "deep sleep cancellation failed: %d\n", ret); return ret; } priv->deep_sleep_required = 1; @@ -618,7 +605,8 @@ int lbs_resume(struct lbs_private *priv) priv->deep_sleep_required = 0; ret = lbs_set_deep_sleep(priv, 1); if (ret) - lbs_pr_err("deep sleep activation failed: %d\n", ret); + netdev_err(priv->dev, + "deep sleep activation failed: %d\n", ret); } if (priv->setup_fw_on_resume) @@ -630,8 +618,10 @@ int lbs_resume(struct lbs_private *priv) EXPORT_SYMBOL_GPL(lbs_resume); /** - * This function handles the timeout of command sending. - * It will re-send the same command again. + * lbs_cmd_timeout_handler - handles the timeout of command sending. + * It will re-send the same command again. + * + * @data: &struct lbs_private pointer */ static void lbs_cmd_timeout_handler(unsigned long data) { @@ -644,8 +634,8 @@ static void lbs_cmd_timeout_handler(unsigned long data) if (!priv->cur_cmd) goto out; - lbs_pr_info("command 0x%04x timed out\n", - le16_to_cpu(priv->cur_cmd->cmdbuf->command)); + netdev_info(priv->dev, "command 0x%04x timed out\n", + le16_to_cpu(priv->cur_cmd->cmdbuf->command)); priv->cmd_timed_out = 1; wake_up_interruptible(&priv->waitq); @@ -655,8 +645,10 @@ out: } /** - * This function put the device back to deep sleep mode when timer expires - * and no activity (command, event, data etc.) is detected. + * auto_deepsleep_timer_fn - put the device back to deep sleep mode when + * timer expires and no activity (command, event, data etc.) is detected. + * @data: &struct lbs_private pointer + * returns: N/A */ static void auto_deepsleep_timer_fn(unsigned long data) { @@ -748,7 +740,7 @@ static int lbs_init_adapter(struct lbs_private *priv) /* Allocate the command buffers */ if (lbs_allocate_cmd_buffer(priv)) { - lbs_pr_err("Out of memory allocating command buffers\n"); + pr_err("Out of memory allocating command buffers\n"); ret = -ENOMEM; goto out; } @@ -758,7 +750,7 @@ static int lbs_init_adapter(struct lbs_private *priv) /* Create the event FIFO */ ret = kfifo_alloc(&priv->event_fifo, sizeof(u32) * 16, GFP_KERNEL); if (ret) { - lbs_pr_err("Out of memory allocating event FIFO buffer\n"); + pr_err("Out of memory allocating event FIFO buffer\n"); goto out; } @@ -785,18 +777,18 @@ static const struct net_device_ops lbs_netdev_ops = { .ndo_stop = lbs_eth_stop, .ndo_start_xmit = lbs_hard_start_xmit, .ndo_set_mac_address = lbs_set_mac_address, - .ndo_tx_timeout = lbs_tx_timeout, .ndo_set_multicast_list = lbs_set_multicast_list, .ndo_change_mtu = eth_change_mtu, .ndo_validate_addr = eth_validate_addr, }; /** - * @brief This function adds the card. it will probe the + * lbs_add_card - adds the card. It will probe the * card, allocate the lbs_priv and initialize the device. * - * @param card A pointer to card - * @return A pointer to struct lbs_private structure + * @card: A pointer to card + * @dmdev: A pointer to &struct device + * returns: A pointer to &struct lbs_private structure */ struct lbs_private *lbs_add_card(void *card, struct device *dmdev) { @@ -809,7 +801,7 @@ struct lbs_private *lbs_add_card(void *card, struct device *dmdev) /* Allocate an Ethernet device and register it */ wdev = lbs_cfg_alloc(dmdev); if (IS_ERR(wdev)) { - lbs_pr_err("cfg80211 init failed\n"); + pr_err("cfg80211 init failed\n"); goto done; } @@ -818,7 +810,7 @@ struct lbs_private *lbs_add_card(void *card, struct device *dmdev) priv->wdev = wdev; if (lbs_init_adapter(priv)) { - lbs_pr_err("failed to initialize adapter structure.\n"); + pr_err("failed to initialize adapter structure\n"); goto err_wdev; } @@ -950,17 +942,20 @@ int lbs_start_card(struct lbs_private *priv) goto done; if (lbs_cfg_register(priv)) { - lbs_pr_err("cannot register device\n"); + pr_err("cannot register device\n"); goto done; } lbs_update_channel(priv); - lbs_init_mesh(priv); + if (!lbs_disablemesh) + lbs_init_mesh(priv); + else + pr_info("%s: mesh disabled\n", dev->name); lbs_debugfs_init_one(priv, dev); - lbs_pr_info("%s: Marvell WLAN 802.11 adapter\n", dev->name); + netdev_info(dev, "Marvell WLAN 802.11 adapter\n"); ret = 0; @@ -1057,19 +1052,19 @@ void lbs_notify_command_response(struct lbs_private *priv, u8 resp_idx) EXPORT_SYMBOL_GPL(lbs_notify_command_response); /** - * @brief Retrieves two-stage firmware + * lbs_get_firmware - Retrieves two-stage firmware * - * @param dev A pointer to device structure - * @param user_helper User-defined helper firmware file - * @param user_mainfw User-defined main firmware file - * @param card_model Bus-specific card model ID used to filter firmware table - * elements - * @param fw_table Table of firmware file names and device model numbers - * terminated by an entry with a NULL helper name - * @param helper On success, the helper firmware; caller must free - * @param mainfw On success, the main firmware; caller must free + * @dev: A pointer to &device structure + * @user_helper: User-defined helper firmware file + * @user_mainfw: User-defined main firmware file + * @card_model: Bus-specific card model ID used to filter firmware table + * elements + * @fw_table: Table of firmware file names and device model numbers + * terminated by an entry with a NULL helper name + * @helper: On success, the helper firmware; caller must free + * @mainfw: On success, the main firmware; caller must free * - * @return 0 on success, non-zero on failure + * returns: 0 on success, non-zero on failure */ int lbs_get_firmware(struct device *dev, const char *user_helper, const char *user_mainfw, u32 card_model, @@ -1087,16 +1082,16 @@ int lbs_get_firmware(struct device *dev, const char *user_helper, if (user_helper) { ret = request_firmware(helper, user_helper, dev); if (ret) { - lbs_pr_err("couldn't find helper firmware %s", - user_helper); + dev_err(dev, "couldn't find helper firmware %s\n", + user_helper); goto fail; } } if (user_mainfw) { ret = request_firmware(mainfw, user_mainfw, dev); if (ret) { - lbs_pr_err("couldn't find main firmware %s", - user_mainfw); + dev_err(dev, "couldn't find main firmware %s\n", + user_mainfw); goto fail; } } diff --git a/drivers/net/wireless/libertas/mesh.c b/drivers/net/wireless/libertas/mesh.c index 9d097b9c800..24cf06680c6 100644 --- a/drivers/net/wireless/libertas/mesh.c +++ b/drivers/net/wireless/libertas/mesh.c @@ -1,3 +1,5 @@ +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/delay.h> #include <linux/etherdevice.h> #include <linux/netdevice.h> @@ -16,12 +18,15 @@ * Mesh sysfs support */ -/** +/* * Attributes exported through sysfs */ /** - * @brief Get function for sysfs attribute anycast_mask + * lbs_anycast_get - Get function for sysfs attribute anycast_mask + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t lbs_anycast_get(struct device *dev, struct device_attribute *attr, char * buf) @@ -40,7 +45,11 @@ static ssize_t lbs_anycast_get(struct device *dev, } /** - * @brief Set function for sysfs attribute anycast_mask + * lbs_anycast_set - Set function for sysfs attribute anycast_mask + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t lbs_anycast_set(struct device *dev, struct device_attribute *attr, const char * buf, size_t count) @@ -62,7 +71,10 @@ static ssize_t lbs_anycast_set(struct device *dev, } /** - * @brief Get function for sysfs attribute prb_rsp_limit + * lbs_prb_rsp_limit_get - Get function for sysfs attribute prb_rsp_limit + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t lbs_prb_rsp_limit_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -85,7 +97,11 @@ static ssize_t lbs_prb_rsp_limit_get(struct device *dev, } /** - * @brief Set function for sysfs attribute prb_rsp_limit + * lbs_prb_rsp_limit_set - Set function for sysfs attribute prb_rsp_limit + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t lbs_prb_rsp_limit_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -114,7 +130,10 @@ static ssize_t lbs_prb_rsp_limit_set(struct device *dev, } /** - * Get function for sysfs attribute mesh + * lbs_mesh_get - Get function for sysfs attribute mesh + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t lbs_mesh_get(struct device *dev, struct device_attribute *attr, char * buf) @@ -124,7 +143,11 @@ static ssize_t lbs_mesh_get(struct device *dev, } /** - * Set function for sysfs attribute mesh + * lbs_mesh_set - Set function for sysfs attribute mesh + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t lbs_mesh_set(struct device *dev, struct device_attribute *attr, const char * buf, size_t count) @@ -151,19 +174,19 @@ static ssize_t lbs_mesh_set(struct device *dev, return count; } -/** +/* * lbs_mesh attribute to be exported per ethX interface * through sysfs (/sys/class/net/ethX/lbs_mesh) */ static DEVICE_ATTR(lbs_mesh, 0644, lbs_mesh_get, lbs_mesh_set); -/** +/* * anycast_mask attribute to be exported per mshX interface * through sysfs (/sys/class/net/mshX/anycast_mask) */ static DEVICE_ATTR(anycast_mask, 0644, lbs_anycast_get, lbs_anycast_set); -/** +/* * prb_rsp_limit attribute to be exported per mshX interface * through sysfs (/sys/class/net/mshX/prb_rsp_limit) */ @@ -246,7 +269,7 @@ int lbs_init_mesh(struct lbs_private *priv) lbs_add_mesh(priv); if (device_create_file(&dev->dev, &dev_attr_lbs_mesh)) - lbs_pr_err("cannot register lbs_mesh attribute\n"); + netdev_err(dev, "cannot register lbs_mesh attribute\n"); ret = 1; } @@ -274,10 +297,10 @@ int lbs_deinit_mesh(struct lbs_private *priv) /** - * @brief This function closes the mshX interface + * lbs_mesh_stop - close the mshX interface * - * @param dev A pointer to net_device structure - * @return 0 + * @dev: A pointer to &net_device structure + * returns: 0 */ static int lbs_mesh_stop(struct net_device *dev) { @@ -301,10 +324,10 @@ static int lbs_mesh_stop(struct net_device *dev) } /** - * @brief This function opens the mshX interface + * lbs_mesh_dev_open - open the mshX interface * - * @param dev A pointer to net_device structure - * @return 0 or -EBUSY if monitor mode active + * @dev: A pointer to &net_device structure + * returns: 0 or -EBUSY if monitor mode active */ static int lbs_mesh_dev_open(struct net_device *dev) { @@ -342,10 +365,10 @@ static const struct net_device_ops mesh_netdev_ops = { }; /** - * @brief This function adds mshX interface + * lbs_add_mesh - add mshX interface * - * @param priv A pointer to the struct lbs_private structure - * @return 0 if successful, -X otherwise + * @priv: A pointer to the &struct lbs_private structure + * returns: 0 if successful, -X otherwise */ int lbs_add_mesh(struct lbs_private *priv) { @@ -374,7 +397,7 @@ int lbs_add_mesh(struct lbs_private *priv) /* Register virtual mesh interface */ ret = register_netdev(mesh_dev); if (ret) { - lbs_pr_err("cannot register mshX virtual interface\n"); + pr_err("cannot register mshX virtual interface\n"); goto err_free; } @@ -456,13 +479,13 @@ void lbs_mesh_set_txpd(struct lbs_private *priv, */ /** - * @brief Add or delete Mesh Blinding Table entries + * lbs_mesh_bt_add_del - Add or delete Mesh Blinding Table entries * - * @param priv A pointer to struct lbs_private structure - * @param add TRUE to add the entry, FALSE to delete it - * @param addr1 Destination address to blind or unblind + * @priv: A pointer to &struct lbs_private structure + * @add: TRUE to add the entry, FALSE to delete it + * @addr1: Destination address to blind or unblind * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_mesh_bt_add_del(struct lbs_private *priv, bool add, u8 *addr1) { @@ -493,11 +516,11 @@ int lbs_mesh_bt_add_del(struct lbs_private *priv, bool add, u8 *addr1) } /** - * @brief Reset/clear the mesh blinding table + * lbs_mesh_bt_reset - Reset/clear the mesh blinding table * - * @param priv A pointer to struct lbs_private structure + * @priv: A pointer to &struct lbs_private structure * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_mesh_bt_reset(struct lbs_private *priv) { @@ -517,17 +540,18 @@ int lbs_mesh_bt_reset(struct lbs_private *priv) } /** - * @brief Gets the inverted status of the mesh blinding table + * lbs_mesh_bt_get_inverted - Gets the inverted status of the mesh + * blinding table * - * Normally the firmware "blinds" or ignores traffic from mesh nodes in the - * table, but an inverted table allows *only* traffic from nodes listed in - * the table. + * Normally the firmware "blinds" or ignores traffic from mesh nodes in the + * table, but an inverted table allows *only* traffic from nodes listed in + * the table. * - * @param priv A pointer to struct lbs_private structure - * @param invert On success, TRUE if the blinding table is inverted, - * FALSE if it is not inverted + * @priv: A pointer to &struct lbs_private structure + * @inverted: On success, TRUE if the blinding table is inverted, + * FALSE if it is not inverted * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_mesh_bt_get_inverted(struct lbs_private *priv, bool *inverted) { @@ -551,18 +575,19 @@ int lbs_mesh_bt_get_inverted(struct lbs_private *priv, bool *inverted) } /** - * @brief Sets the inverted status of the mesh blinding table + * lbs_mesh_bt_set_inverted - Sets the inverted status of the mesh + * blinding table * - * Normally the firmware "blinds" or ignores traffic from mesh nodes in the - * table, but an inverted table allows *only* traffic from nodes listed in - * the table. + * Normally the firmware "blinds" or ignores traffic from mesh nodes in the + * table, but an inverted table allows *only* traffic from nodes listed in + * the table. * - * @param priv A pointer to struct lbs_private structure - * @param invert TRUE to invert the blinding table (only traffic from - * listed nodes allowed), FALSE to return it - * to normal state (listed nodes ignored) + * @priv: A pointer to &struct lbs_private structure + * @inverted: TRUE to invert the blinding table (only traffic from + * listed nodes allowed), FALSE to return it + * to normal state (listed nodes ignored) * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_mesh_bt_set_inverted(struct lbs_private *priv, bool inverted) { @@ -583,13 +608,13 @@ int lbs_mesh_bt_set_inverted(struct lbs_private *priv, bool inverted) } /** - * @brief List an entry in the mesh blinding table + * lbs_mesh_bt_get_entry - List an entry in the mesh blinding table * - * @param priv A pointer to struct lbs_private structure - * @param id The ID of the entry to list - * @param addr1 MAC address associated with the table entry + * @priv: A pointer to &struct lbs_private structure + * @id: The ID of the entry to list + * @addr1: MAC address associated with the table entry * - * @return 0 on success, error on failure + * returns: 0 on success, error on failure */ int lbs_mesh_bt_get_entry(struct lbs_private *priv, u32 id, u8 *addr1) { @@ -614,14 +639,14 @@ int lbs_mesh_bt_get_entry(struct lbs_private *priv, u32 id, u8 *addr1) } /** - * @brief Access the mesh forwarding table + * lbs_cmd_fwt_access - Access the mesh forwarding table * - * @param priv A pointer to struct lbs_private structure - * @param cmd_action The forwarding table action to perform - * @param cmd The pre-filled FWT_ACCESS command + * @priv: A pointer to &struct lbs_private structure + * @cmd_action: The forwarding table action to perform + * @cmd: The pre-filled FWT_ACCESS command * - * @return 0 on success and 'cmd' will be filled with the - * firmware's response + * returns: 0 on success and 'cmd' will be filled with the + * firmware's response */ int lbs_cmd_fwt_access(struct lbs_private *priv, u16 cmd_action, struct cmd_ds_fwt_access *cmd) @@ -774,7 +799,10 @@ static int mesh_get_default_parameters(struct device *dev, } /** - * @brief Get function for sysfs attribute bootflag + * bootflag_get - Get function for sysfs attribute bootflag + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t bootflag_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -791,7 +819,11 @@ static ssize_t bootflag_get(struct device *dev, } /** - * @brief Set function for sysfs attribute bootflag + * bootflag_set - Set function for sysfs attribute bootflag + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t bootflag_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -817,7 +849,10 @@ static ssize_t bootflag_set(struct device *dev, struct device_attribute *attr, } /** - * @brief Get function for sysfs attribute boottime + * boottime_get - Get function for sysfs attribute boottime + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t boottime_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -834,7 +869,11 @@ static ssize_t boottime_get(struct device *dev, } /** - * @brief Set function for sysfs attribute boottime + * boottime_set - Set function for sysfs attribute boottime + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t boottime_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -869,7 +908,10 @@ static ssize_t boottime_set(struct device *dev, } /** - * @brief Get function for sysfs attribute channel + * channel_get - Get function for sysfs attribute channel + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t channel_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -886,7 +928,11 @@ static ssize_t channel_get(struct device *dev, } /** - * @brief Set function for sysfs attribute channel + * channel_set - Set function for sysfs attribute channel + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t channel_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -912,7 +958,10 @@ static ssize_t channel_set(struct device *dev, struct device_attribute *attr, } /** - * @brief Get function for sysfs attribute mesh_id + * mesh_id_get - Get function for sysfs attribute mesh_id + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t mesh_id_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -926,7 +975,7 @@ static ssize_t mesh_id_get(struct device *dev, struct device_attribute *attr, return ret; if (defs.meshie.val.mesh_id_len > IEEE80211_MAX_SSID_LEN) { - lbs_pr_err("inconsistent mesh ID length"); + dev_err(dev, "inconsistent mesh ID length\n"); defs.meshie.val.mesh_id_len = IEEE80211_MAX_SSID_LEN; } @@ -938,7 +987,11 @@ static ssize_t mesh_id_get(struct device *dev, struct device_attribute *attr, } /** - * @brief Set function for sysfs attribute mesh_id + * mesh_id_set - Set function for sysfs attribute mesh_id + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t mesh_id_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -980,7 +1033,10 @@ static ssize_t mesh_id_set(struct device *dev, struct device_attribute *attr, } /** - * @brief Get function for sysfs attribute protocol_id + * protocol_id_get - Get function for sysfs attribute protocol_id + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t protocol_id_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -997,7 +1053,11 @@ static ssize_t protocol_id_get(struct device *dev, } /** - * @brief Set function for sysfs attribute protocol_id + * protocol_id_set - Set function for sysfs attribute protocol_id + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t protocol_id_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -1034,7 +1094,10 @@ static ssize_t protocol_id_set(struct device *dev, } /** - * @brief Get function for sysfs attribute metric_id + * metric_id_get - Get function for sysfs attribute metric_id + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t metric_id_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -1051,7 +1114,11 @@ static ssize_t metric_id_get(struct device *dev, } /** - * @brief Set function for sysfs attribute metric_id + * metric_id_set - Set function for sysfs attribute metric_id + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t metric_id_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) @@ -1088,7 +1155,10 @@ static ssize_t metric_id_set(struct device *dev, struct device_attribute *attr, } /** - * @brief Get function for sysfs attribute capability + * capability_get - Get function for sysfs attribute capability + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer where data will be returned */ static ssize_t capability_get(struct device *dev, struct device_attribute *attr, char *buf) @@ -1105,7 +1175,11 @@ static ssize_t capability_get(struct device *dev, } /** - * @brief Set function for sysfs attribute capability + * capability_set - Set function for sysfs attribute capability + * @dev: the &struct device + * @attr: device attributes + * @buf: buffer that contains new attribute value + * @count: size of buffer */ static ssize_t capability_set(struct device *dev, struct device_attribute *attr, const char *buf, size_t count) diff --git a/drivers/net/wireless/libertas/mesh.h b/drivers/net/wireless/libertas/mesh.h index afb2e8dead3..ee95c73ed5f 100644 --- a/drivers/net/wireless/libertas/mesh.h +++ b/drivers/net/wireless/libertas/mesh.h @@ -1,6 +1,6 @@ -/** - * Contains all definitions needed for the Libertas' MESH implementation. - */ +/* + * Contains all definitions needed for the Libertas' MESH implementation. + */ #ifndef _LBS_MESH_H_ #define _LBS_MESH_H_ diff --git a/drivers/net/wireless/libertas/rx.c b/drivers/net/wireless/libertas/rx.c index a2b1df21d28..fdb0448301a 100644 --- a/drivers/net/wireless/libertas/rx.c +++ b/drivers/net/wireless/libertas/rx.c @@ -1,6 +1,9 @@ -/** - * This file contains the handling of RX in wlan driver. - */ +/* + * This file contains the handling of RX in wlan driver. + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + #include <linux/etherdevice.h> #include <linux/slab.h> #include <linux/types.h> @@ -40,12 +43,12 @@ static int process_rxed_802_11_packet(struct lbs_private *priv, struct sk_buff *skb); /** - * @brief This function processes received packet and forwards it - * to kernel/upper layer + * lbs_process_rxed_packet - processes received packet and forwards it + * to kernel/upper layer * - * @param priv A pointer to struct lbs_private - * @param skb A pointer to skb which includes the received packet - * @return 0 or -1 + * @priv: A pointer to &struct lbs_private + * @skb: A pointer to skb which includes the received packet + * returns: 0 or -1 */ int lbs_process_rxed_packet(struct lbs_private *priv, struct sk_buff *skb) { @@ -156,11 +159,11 @@ done: EXPORT_SYMBOL_GPL(lbs_process_rxed_packet); /** - * @brief This function converts Tx/Rx rates from the Marvell WLAN format - * (see Table 2 in Section 3.1) to IEEE80211_RADIOTAP_RATE units (500 Kb/s) + * convert_mv_rate_to_radiotap - converts Tx/Rx rates from Marvell WLAN format + * (see Table 2 in Section 3.1) to IEEE80211_RADIOTAP_RATE units (500 Kb/s) * - * @param rate Input rate - * @return Output Rate (0 if invalid) + * @rate: Input rate + * returns: Output Rate (0 if invalid) */ static u8 convert_mv_rate_to_radiotap(u8 rate) { @@ -191,17 +194,17 @@ static u8 convert_mv_rate_to_radiotap(u8 rate) case 12: /* 54 Mbps */ return 108; } - lbs_pr_alert("Invalid Marvell WLAN rate %i\n", rate); + pr_alert("Invalid Marvell WLAN rate %i\n", rate); return 0; } /** - * @brief This function processes a received 802.11 packet and forwards it - * to kernel/upper layer + * process_rxed_802_11_packet - processes a received 802.11 packet and forwards + * it to kernel/upper layer * - * @param priv A pointer to struct lbs_private - * @param skb A pointer to skb which includes the received packet - * @return 0 or -1 + * @priv: A pointer to &struct lbs_private + * @skb: A pointer to skb which includes the received packet + * returns: 0 or -1 */ static int process_rxed_802_11_packet(struct lbs_private *priv, struct sk_buff *skb) @@ -248,7 +251,7 @@ static int process_rxed_802_11_packet(struct lbs_private *priv, /* add space for the new radio header */ if ((skb_headroom(skb) < sizeof(struct rx_radiotap_hdr)) && pskb_expand_head(skb, sizeof(struct rx_radiotap_hdr), 0, GFP_ATOMIC)) { - lbs_pr_alert("%s: couldn't pskb_expand_head\n", __func__); + netdev_alert(dev, "%s: couldn't pskb_expand_head\n", __func__); ret = -ENOMEM; kfree_skb(skb); goto done; diff --git a/drivers/net/wireless/libertas/tx.c b/drivers/net/wireless/libertas/tx.c index 8000ca6165d..bbb95f88dc0 100644 --- a/drivers/net/wireless/libertas/tx.c +++ b/drivers/net/wireless/libertas/tx.c @@ -1,6 +1,6 @@ -/** - * This file contains the handling of TX in wlan driver. - */ +/* + * This file contains the handling of TX in wlan driver. + */ #include <linux/netdevice.h> #include <linux/etherdevice.h> #include <linux/sched.h> @@ -13,11 +13,11 @@ #include "dev.h" /** - * @brief This function converts Tx/Rx rates from IEEE80211_RADIOTAP_RATE - * units (500 Kb/s) into Marvell WLAN format (see Table 8 in Section 3.2.1) + * convert_radiotap_rate_to_mv - converts Tx/Rx rates from IEEE80211_RADIOTAP_RATE + * units (500 Kb/s) into Marvell WLAN format (see Table 8 in Section 3.2.1) * - * @param rate Input rate - * @return Output Rate (0 if invalid) + * @rate: Input rate + * returns: Output Rate (0 if invalid) */ static u32 convert_radiotap_rate_to_mv(u8 rate) { @@ -51,12 +51,12 @@ static u32 convert_radiotap_rate_to_mv(u8 rate) } /** - * @brief This function checks the conditions and sends packet to IF - * layer if everything is ok. + * lbs_hard_start_xmit - checks the conditions and sends packet to IF + * layer if everything is ok * - * @param priv A pointer to struct lbs_private structure - * @param skb A pointer to skb which includes TX packet - * @return 0 or -1 + * @skb: A pointer to skb which includes TX packet + * @dev: A pointer to the &struct net_device + * returns: 0 or -1 */ netdev_tx_t lbs_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) { @@ -168,13 +168,13 @@ netdev_tx_t lbs_hard_start_xmit(struct sk_buff *skb, struct net_device *dev) } /** - * @brief This function sends to the host the last transmitted packet, - * filling the radiotap headers with transmission information. + * lbs_send_tx_feedback - sends to the host the last transmitted packet, + * filling the radiotap headers with transmission information. * - * @param priv A pointer to struct lbs_private structure - * @param status A 32 bit value containing transmission status. + * @priv: A pointer to &struct lbs_private structure + * @try_count: A 32-bit value containing transmission retry status. * - * @returns void + * returns: void */ void lbs_send_tx_feedback(struct lbs_private *priv, u32 try_count) { diff --git a/drivers/net/wireless/libertas/types.h b/drivers/net/wireless/libertas/types.h index 462fbb4cb74..cf1d9b047ee 100644 --- a/drivers/net/wireless/libertas/types.h +++ b/drivers/net/wireless/libertas/types.h @@ -1,6 +1,6 @@ -/** - * This header file contains definition for global types - */ +/* + * This header file contains definition for global types + */ #ifndef _LBS_TYPES_H_ #define _LBS_TYPES_H_ @@ -54,7 +54,7 @@ union ieee_phy_param_set { struct ieee_ie_ds_param_set ds; } __packed; -/** TLV type ID definition */ +/* TLV type ID definition */ #define PROPRIETARY_TLV_BASE_ID 0x0100 /* Terminating TLV type */ @@ -96,7 +96,7 @@ union ieee_phy_param_set { #define TLV_TYPE_MESH_ID (PROPRIETARY_TLV_BASE_ID + 37) #define TLV_TYPE_OLD_MESH_ID (PROPRIETARY_TLV_BASE_ID + 291) -/** TLV related data structures*/ +/* TLV related data structures */ struct mrvl_ie_header { __le16 type; __le16 len; @@ -177,7 +177,7 @@ struct mrvl_ie_auth_type { __le16 auth; } __packed; -/** Local Power capability */ +/* Local Power capability */ struct mrvl_ie_power_capability { struct mrvl_ie_header header; s8 minpower; @@ -235,9 +235,11 @@ struct mrvl_ie_ledbhv { struct led_bhv ledbhv[1]; } __packed; -/* Meant to be packed as the value member of a struct ieee80211_info_element. +/* + * Meant to be packed as the value member of a struct ieee80211_info_element. * Note that the len member of the ieee80211_info_element varies depending on - * the mesh_id_len */ + * the mesh_id_len + */ struct mrvl_meshie_val { uint8_t oui[3]; uint8_t type; |