diff options
Diffstat (limited to 'drivers/net/wireless/rt2x00/rt2800pci.c')
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt2800pci.c | 366 |
1 files changed, 167 insertions, 199 deletions
diff --git a/drivers/net/wireless/rt2x00/rt2800pci.c b/drivers/net/wireless/rt2x00/rt2800pci.c index b2f23272c3a..39b3846fa34 100644 --- a/drivers/net/wireless/rt2x00/rt2800pci.c +++ b/drivers/net/wireless/rt2x00/rt2800pci.c @@ -31,7 +31,6 @@ Supported chipsets: RT2800E & RT2800ED. */ -#include <linux/crc-ccitt.h> #include <linux/delay.h> #include <linux/etherdevice.h> #include <linux/init.h> @@ -51,7 +50,7 @@ /* * Allow hardware encryption to be disabled. */ -static int modparam_nohwcrypt = 1; +static int modparam_nohwcrypt = 0; module_param_named(nohwcrypt, modparam_nohwcrypt, bool, S_IRUGO); MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); @@ -139,8 +138,18 @@ static void rt2800pci_read_eeprom_pci(struct rt2x00_dev *rt2x00dev) eeprom.data = rt2x00dev; eeprom.register_read = rt2800pci_eepromregister_read; eeprom.register_write = rt2800pci_eepromregister_write; - eeprom.width = !rt2x00_get_field32(reg, E2PROM_CSR_TYPE) ? - PCI_EEPROM_WIDTH_93C46 : PCI_EEPROM_WIDTH_93C66; + switch (rt2x00_get_field32(reg, E2PROM_CSR_TYPE)) + { + case 0: + eeprom.width = PCI_EEPROM_WIDTH_93C46; + break; + case 1: + eeprom.width = PCI_EEPROM_WIDTH_93C66; + break; + default: + eeprom.width = PCI_EEPROM_WIDTH_93C86; + break; + } eeprom.reg_data_in = 0; eeprom.reg_data_out = 0; eeprom.reg_data_clock = 0; @@ -182,82 +191,14 @@ static char *rt2800pci_get_firmware_name(struct rt2x00_dev *rt2x00dev) return FIRMWARE_RT2860; } -static int rt2800pci_check_firmware(struct rt2x00_dev *rt2x00dev, +static int rt2800pci_write_firmware(struct rt2x00_dev *rt2x00dev, const u8 *data, const size_t len) { - u16 fw_crc; - u16 crc; - - /* - * Only support 8kb firmware files. - */ - if (len != 8192) - return FW_BAD_LENGTH; - - /* - * The last 2 bytes in the firmware array are the crc checksum itself, - * this means that we should never pass those 2 bytes to the crc - * algorithm. - */ - fw_crc = (data[len - 2] << 8 | data[len - 1]); - - /* - * Use the crc ccitt algorithm. - * This will return the same value as the legacy driver which - * used bit ordering reversion on the both the firmware bytes - * before input input as well as on the final output. - * Obviously using crc ccitt directly is much more efficient. - */ - crc = crc_ccitt(~0, data, len - 2); - - /* - * There is a small difference between the crc-itu-t + bitrev and - * the crc-ccitt crc calculation. In the latter method the 2 bytes - * will be swapped, use swab16 to convert the crc to the correct - * value. - */ - crc = swab16(crc); - - return (fw_crc == crc) ? FW_OK : FW_BAD_CRC; -} - -static int rt2800pci_load_firmware(struct rt2x00_dev *rt2x00dev, - const u8 *data, const size_t len) -{ - unsigned int i; u32 reg; - /* - * Wait for stable hardware. - */ - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2800_register_read(rt2x00dev, MAC_CSR0, ®); - if (reg && reg != ~0) - break; - msleep(1); - } - - if (i == REGISTER_BUSY_COUNT) { - ERROR(rt2x00dev, "Unstable hardware.\n"); - return -EBUSY; - } - - rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000002); rt2800_register_write(rt2x00dev, AUTOWAKEUP_CFG, 0x00000000); /* - * Disable DMA, will be reenabled later when enabling - * the radio. - */ - rt2800_register_read(rt2x00dev, WPDMA_GLO_CFG, ®); - rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_TX_DMA, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_DMA_BUSY, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_ENABLE_RX_DMA, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_RX_DMA_BUSY, 0); - rt2x00_set_field32(®, WPDMA_GLO_CFG_TX_WRITEBACK_DONE, 1); - rt2800_register_write(rt2x00dev, WPDMA_GLO_CFG, reg); - - /* * enable Host program ram write selection */ reg = 0; @@ -268,34 +209,11 @@ static int rt2800pci_load_firmware(struct rt2x00_dev *rt2x00dev, * Write firmware to device. */ rt2800_register_multiwrite(rt2x00dev, FIRMWARE_IMAGE_BASE, - data, len); + data, len); rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000); rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00001); - /* - * Wait for device to stabilize. - */ - for (i = 0; i < REGISTER_BUSY_COUNT; i++) { - rt2800_register_read(rt2x00dev, PBF_SYS_CTRL, ®); - if (rt2x00_get_field32(reg, PBF_SYS_CTRL_READY)) - break; - msleep(1); - } - - if (i == REGISTER_BUSY_COUNT) { - ERROR(rt2x00dev, "PBF system register not ready.\n"); - return -EBUSY; - } - - /* - * Disable interrupts - */ - rt2x00dev->ops->lib->set_device_state(rt2x00dev, STATE_RADIO_IRQ_OFF); - - /* - * Initialize BBP R/W access agent - */ rt2800_register_write(rt2x00dev, H2M_BBP_AGENT, 0); rt2800_register_write(rt2x00dev, H2M_MAILBOX_CSR, 0); @@ -412,7 +330,8 @@ static void rt2800pci_toggle_rx(struct rt2x00_dev *rt2x00dev, static void rt2800pci_toggle_irq(struct rt2x00_dev *rt2x00dev, enum dev_state state) { - int mask = (state == STATE_RADIO_IRQ_ON); + int mask = (state == STATE_RADIO_IRQ_ON) || + (state == STATE_RADIO_IRQ_ON_ISR); u32 reg; /* @@ -446,6 +365,38 @@ static void rt2800pci_toggle_irq(struct rt2x00_dev *rt2x00dev, rt2800_register_write(rt2x00dev, INT_MASK_CSR, reg); } +static int rt2800pci_init_registers(struct rt2x00_dev *rt2x00dev) +{ + u32 reg; + + /* + * Reset DMA indexes + */ + rt2800_register_read(rt2x00dev, WPDMA_RST_IDX, ®); + rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX0, 1); + rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX1, 1); + rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX2, 1); + rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX3, 1); + rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX4, 1); + rt2x00_set_field32(®, WPDMA_RST_IDX_DTX_IDX5, 1); + rt2x00_set_field32(®, WPDMA_RST_IDX_DRX_IDX0, 1); + rt2800_register_write(rt2x00dev, WPDMA_RST_IDX, reg); + + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e1f); + rt2800_register_write(rt2x00dev, PBF_SYS_CTRL, 0x00000e00); + + rt2800_register_write(rt2x00dev, PWR_PIN_CFG, 0x00000003); + + rt2800_register_read(rt2x00dev, MAC_SYS_CTRL, ®); + rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_CSR, 1); + rt2x00_set_field32(®, MAC_SYS_CTRL_RESET_BBP, 1); + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, reg); + + rt2800_register_write(rt2x00dev, MAC_SYS_CTRL, 0x00000000); + + return 0; +} + static int rt2800pci_enable_radio(struct rt2x00_dev *rt2x00dev) { u32 reg; @@ -465,7 +416,7 @@ static int rt2800pci_enable_radio(struct rt2x00_dev *rt2x00dev) /* * Send signal to firmware during boot time. */ - rt2800_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0xff, 0, 0); + rt2800_mcu_request(rt2x00dev, MCU_BOOT_SIGNAL, 0, 0, 0); /* * Enable RX. @@ -589,7 +540,9 @@ static int rt2800pci_set_device_state(struct rt2x00_dev *rt2x00dev, rt2800pci_toggle_rx(rt2x00dev, state); break; case STATE_RADIO_IRQ_ON: + case STATE_RADIO_IRQ_ON_ISR: case STATE_RADIO_IRQ_OFF: + case STATE_RADIO_IRQ_OFF_ISR: rt2800pci_toggle_irq(rt2x00dev, state); break; case STATE_DEEP_SLEEP: @@ -613,18 +566,12 @@ static int rt2800pci_set_device_state(struct rt2x00_dev *rt2x00dev, /* * TX descriptor initialization */ -static int rt2800pci_write_tx_data(struct queue_entry* entry, - struct txentry_desc *txdesc) +static void rt2800pci_write_tx_data(struct queue_entry* entry, + struct txentry_desc *txdesc) { - int ret; - - ret = rt2x00pci_write_tx_data(entry, txdesc); - if (ret) - return ret; + __le32 *txwi = (__le32 *) entry->skb->data; - rt2800_write_txwi(entry->skb, txdesc); - - return 0; + rt2800_write_txwi(txwi, txdesc); } @@ -684,49 +631,6 @@ static void rt2800pci_write_tx_desc(struct rt2x00_dev *rt2x00dev, /* * TX data initialization */ -static void rt2800pci_write_beacon(struct queue_entry *entry, - struct txentry_desc *txdesc) -{ - struct rt2x00_dev *rt2x00dev = entry->queue->rt2x00dev; - unsigned int beacon_base; - u32 reg; - - /* - * Disable beaconing while we are reloading the beacon data, - * otherwise we might be sending out invalid data. - */ - rt2800_register_read(rt2x00dev, BCN_TIME_CFG, ®); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 0); - rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); - - /* - * Add the TXWI for the beacon to the skb. - */ - rt2800_write_txwi(entry->skb, txdesc); - skb_push(entry->skb, TXWI_DESC_SIZE); - - /* - * Write entire beacon with TXWI to register. - */ - beacon_base = HW_BEACON_OFFSET(entry->entry_idx); - rt2800_register_multiwrite(rt2x00dev, beacon_base, - entry->skb->data, entry->skb->len); - - /* - * Enable beaconing again. - */ - rt2x00_set_field32(®, BCN_TIME_CFG_TSF_TICKING, 1); - rt2x00_set_field32(®, BCN_TIME_CFG_TBTT_ENABLE, 1); - rt2x00_set_field32(®, BCN_TIME_CFG_BEACON_GEN, 1); - rt2800_register_write(rt2x00dev, BCN_TIME_CFG, reg); - - /* - * Clean up beacon skb. - */ - dev_kfree_skb_any(entry->skb); - entry->skb = NULL; -} - static void rt2800pci_kick_tx_queue(struct rt2x00_dev *rt2x00dev, const enum data_queue_qid queue_idx) { @@ -812,7 +716,7 @@ static void rt2800pci_fill_rxdone(struct queue_entry *entry, /* * Process the RXWI structure that is at the start of the buffer. */ - rt2800_process_rxwi(entry->skb, rxdesc); + rt2800_process_rxwi(entry, rxdesc); /* * Set RX IDX in register to inform hardware that we have handled @@ -832,29 +736,24 @@ static void rt2800pci_txdone(struct rt2x00_dev *rt2x00dev) struct txdone_entry_desc txdesc; u32 word; u32 reg; - u32 old_reg; int wcid, ack, pid, tx_wcid, tx_ack, tx_pid; u16 mcs, real_mcs; + int i; /* - * During each loop we will compare the freshly read - * TX_STA_FIFO register value with the value read from - * the previous loop. If the 2 values are equal then - * we should stop processing because the chance it - * quite big that the device has been unplugged and - * we risk going into an endless loop. + * TX_STA_FIFO is a stack of X entries, hence read TX_STA_FIFO + * at most X times and also stop processing once the TX_STA_FIFO_VALID + * flag is not set anymore. + * + * The legacy drivers use X=TX_RING_SIZE but state in a comment + * that the TX_STA_FIFO stack has a size of 16. We stick to our + * tx ring size for now. */ - old_reg = 0; - - while (1) { + for (i = 0; i < TX_ENTRIES; i++) { rt2800_register_read(rt2x00dev, TX_STA_FIFO, ®); if (!rt2x00_get_field32(reg, TX_STA_FIFO_VALID)) break; - if (old_reg == reg) - break; - old_reg = reg; - wcid = rt2x00_get_field32(reg, TX_STA_FIFO_WCID); ack = rt2x00_get_field32(reg, TX_STA_FIFO_TX_ACK_REQUIRED); pid = rt2x00_get_field32(reg, TX_STA_FIFO_PID_TYPE); @@ -880,8 +779,7 @@ static void rt2800pci_txdone(struct rt2x00_dev *rt2x00dev) /* Check if we got a match by looking at WCID/ACK/PID * fields */ - txwi = (__le32 *)(entry->skb->data - - rt2x00dev->ops->extra_tx_headroom); + txwi = (__le32 *) entry->skb->data; rt2x00_desc_read(txwi, 1, &word); tx_wcid = rt2x00_get_field32(word, TXWI_W1_WIRELESS_CLI_ID); @@ -923,8 +821,12 @@ static void rt2800pci_txdone(struct rt2x00_dev *rt2x00dev) txdesc.retry = 7; } - __set_bit(TXDONE_FALLBACK, &txdesc.flags); - + /* + * the frame was retried at least once + * -> hw used fallback rates + */ + if (txdesc.retry) + __set_bit(TXDONE_FALLBACK, &txdesc.flags); rt2x00lib_txdone(entry, &txdesc); } @@ -938,6 +840,48 @@ static void rt2800pci_wakeup(struct rt2x00_dev *rt2x00dev) rt2800_config(rt2x00dev, &libconf, IEEE80211_CONF_CHANGE_PS); } +static irqreturn_t rt2800pci_interrupt_thread(int irq, void *dev_instance) +{ + struct rt2x00_dev *rt2x00dev = dev_instance; + u32 reg = rt2x00dev->irqvalue[0]; + + /* + * 1 - Pre TBTT interrupt. + */ + if (rt2x00_get_field32(reg, INT_SOURCE_CSR_PRE_TBTT)) + rt2x00lib_pretbtt(rt2x00dev); + + /* + * 2 - Beacondone interrupt. + */ + if (rt2x00_get_field32(reg, INT_SOURCE_CSR_TBTT)) + rt2x00lib_beacondone(rt2x00dev); + + /* + * 3 - Rx ring done interrupt. + */ + if (rt2x00_get_field32(reg, INT_SOURCE_CSR_RX_DONE)) + rt2x00pci_rxdone(rt2x00dev); + + /* + * 4 - Tx done interrupt. + */ + if (rt2x00_get_field32(reg, INT_SOURCE_CSR_TX_FIFO_STATUS)) + rt2800pci_txdone(rt2x00dev); + + /* + * 5 - Auto wakeup interrupt. + */ + if (rt2x00_get_field32(reg, INT_SOURCE_CSR_AUTO_WAKEUP)) + rt2800pci_wakeup(rt2x00dev); + + /* Enable interrupts again. */ + rt2x00dev->ops->lib->set_device_state(rt2x00dev, + STATE_RADIO_IRQ_ON_ISR); + + return IRQ_HANDLED; +} + static irqreturn_t rt2800pci_interrupt(int irq, void *dev_instance) { struct rt2x00_dev *rt2x00dev = dev_instance; @@ -953,19 +897,15 @@ static irqreturn_t rt2800pci_interrupt(int irq, void *dev_instance) if (!test_bit(DEVICE_STATE_ENABLED_RADIO, &rt2x00dev->flags)) return IRQ_HANDLED; - /* - * 1 - Rx ring done interrupt. - */ - if (rt2x00_get_field32(reg, INT_SOURCE_CSR_RX_DONE)) - rt2x00pci_rxdone(rt2x00dev); + /* Store irqvalue for use in the interrupt thread. */ + rt2x00dev->irqvalue[0] = reg; - if (rt2x00_get_field32(reg, INT_SOURCE_CSR_TX_FIFO_STATUS)) - rt2800pci_txdone(rt2x00dev); + /* Disable interrupts, will be enabled again in the interrupt thread. */ + rt2x00dev->ops->lib->set_device_state(rt2x00dev, + STATE_RADIO_IRQ_OFF_ISR); - if (rt2x00_get_field32(reg, INT_SOURCE_CSR_AUTO_WAKEUP)) - rt2800pci_wakeup(rt2x00dev); - return IRQ_HANDLED; + return IRQ_WAKE_THREAD; } /* @@ -986,24 +926,10 @@ static int rt2800pci_validate_eeprom(struct rt2x00_dev *rt2x00dev) return rt2800_validate_eeprom(rt2x00dev); } -static const struct rt2800_ops rt2800pci_rt2800_ops = { - .register_read = rt2x00pci_register_read, - .register_read_lock = rt2x00pci_register_read, /* same for PCI */ - .register_write = rt2x00pci_register_write, - .register_write_lock = rt2x00pci_register_write, /* same for PCI */ - - .register_multiread = rt2x00pci_register_multiread, - .register_multiwrite = rt2x00pci_register_multiwrite, - - .regbusy_read = rt2x00pci_regbusy_read, -}; - static int rt2800pci_probe_hw(struct rt2x00_dev *rt2x00dev) { int retval; - rt2x00dev->priv = (void *)&rt2800pci_rt2800_ops; - /* * Allocate eeprom data. */ @@ -1030,6 +956,12 @@ static int rt2800pci_probe_hw(struct rt2x00_dev *rt2x00dev) __set_bit(DRIVER_SUPPORT_CONTROL_FILTER_PSPOLL, &rt2x00dev->flags); /* + * This device has a pre tbtt interrupt and thus fetches + * a new beacon directly prior to transmission. + */ + __set_bit(DRIVER_SUPPORT_PRE_TBTT_INTERRUPT, &rt2x00dev->flags); + + /* * This device requires firmware. */ if (!rt2x00_is_soc(rt2x00dev)) @@ -1038,6 +970,7 @@ static int rt2800pci_probe_hw(struct rt2x00_dev *rt2x00dev) __set_bit(DRIVER_REQUIRE_L2PAD, &rt2x00dev->flags); if (!modparam_nohwcrypt) __set_bit(CONFIG_SUPPORT_HW_CRYPTO, &rt2x00dev->flags); + __set_bit(DRIVER_SUPPORT_LINK_TUNING, &rt2x00dev->flags); /* * Set the rssi offset. @@ -1047,12 +980,46 @@ static int rt2800pci_probe_hw(struct rt2x00_dev *rt2x00dev) return 0; } +static const struct ieee80211_ops rt2800pci_mac80211_ops = { + .tx = rt2x00mac_tx, + .start = rt2x00mac_start, + .stop = rt2x00mac_stop, + .add_interface = rt2x00mac_add_interface, + .remove_interface = rt2x00mac_remove_interface, + .config = rt2x00mac_config, + .configure_filter = rt2x00mac_configure_filter, + .set_key = rt2x00mac_set_key, + .sw_scan_start = rt2x00mac_sw_scan_start, + .sw_scan_complete = rt2x00mac_sw_scan_complete, + .get_stats = rt2x00mac_get_stats, + .get_tkip_seq = rt2800_get_tkip_seq, + .set_rts_threshold = rt2800_set_rts_threshold, + .bss_info_changed = rt2x00mac_bss_info_changed, + .conf_tx = rt2800_conf_tx, + .get_tsf = rt2800_get_tsf, + .rfkill_poll = rt2x00mac_rfkill_poll, + .ampdu_action = rt2800_ampdu_action, +}; + +static const struct rt2800_ops rt2800pci_rt2800_ops = { + .register_read = rt2x00pci_register_read, + .register_read_lock = rt2x00pci_register_read, /* same for PCI */ + .register_write = rt2x00pci_register_write, + .register_write_lock = rt2x00pci_register_write, /* same for PCI */ + .register_multiread = rt2x00pci_register_multiread, + .register_multiwrite = rt2x00pci_register_multiwrite, + .regbusy_read = rt2x00pci_regbusy_read, + .drv_write_firmware = rt2800pci_write_firmware, + .drv_init_registers = rt2800pci_init_registers, +}; + static const struct rt2x00lib_ops rt2800pci_rt2x00_ops = { .irq_handler = rt2800pci_interrupt, + .irq_handler_thread = rt2800pci_interrupt_thread, .probe_hw = rt2800pci_probe_hw, .get_firmware_name = rt2800pci_get_firmware_name, - .check_firmware = rt2800pci_check_firmware, - .load_firmware = rt2800pci_load_firmware, + .check_firmware = rt2800_check_firmware, + .load_firmware = rt2800_load_firmware, .initialize = rt2x00pci_initialize, .uninitialize = rt2x00pci_uninitialize, .get_entry_state = rt2800pci_get_entry_state, @@ -1064,7 +1031,7 @@ static const struct rt2x00lib_ops rt2800pci_rt2x00_ops = { .link_tuner = rt2800_link_tuner, .write_tx_desc = rt2800pci_write_tx_desc, .write_tx_data = rt2800pci_write_tx_data, - .write_beacon = rt2800pci_write_beacon, + .write_beacon = rt2800_write_beacon, .kick_tx_queue = rt2800pci_kick_tx_queue, .kill_tx_queue = rt2800pci_kill_tx_queue, .fill_rxdone = rt2800pci_fill_rxdone, @@ -1110,7 +1077,8 @@ static const struct rt2x00_ops rt2800pci_ops = { .tx = &rt2800pci_queue_tx, .bcn = &rt2800pci_queue_bcn, .lib = &rt2800pci_rt2x00_ops, - .hw = &rt2800_mac80211_ops, + .drv = &rt2800pci_rt2800_ops, + .hw = &rt2800pci_mac80211_ops, #ifdef CONFIG_RT2X00_LIB_DEBUGFS .debugfs = &rt2800_rt2x00debug, #endif /* CONFIG_RT2X00_LIB_DEBUGFS */ |