diff options
Diffstat (limited to 'drivers/net/wireless/rt2x00/rt61pci.c')
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt61pci.c | 45 |
1 files changed, 31 insertions, 14 deletions
diff --git a/drivers/net/wireless/rt2x00/rt61pci.c b/drivers/net/wireless/rt2x00/rt61pci.c index 243df08ae91..7ca383478ee 100644 --- a/drivers/net/wireless/rt2x00/rt61pci.c +++ b/drivers/net/wireless/rt2x00/rt61pci.c @@ -931,6 +931,9 @@ static void rt61pci_config_retry_limit(struct rt2x00_dev *rt2x00dev, u32 reg; rt2x00pci_register_read(rt2x00dev, TXRX_CSR4, ®); + rt2x00_set_field32(®, TXRX_CSR4_OFDM_TX_RATE_DOWN, 1); + rt2x00_set_field32(®, TXRX_CSR4_OFDM_TX_RATE_STEP, 0); + rt2x00_set_field32(®, TXRX_CSR4_OFDM_TX_FALLBACK_CCK, 0); rt2x00_set_field32(®, TXRX_CSR4_LONG_RETRY_LIMIT, libconf->conf->long_frame_max_tx_count); rt2x00_set_field32(®, TXRX_CSR4_SHORT_RETRY_LIMIT, @@ -2049,29 +2052,24 @@ static void rt61pci_txdone(struct rt2x00_dev *rt2x00dev) struct txdone_entry_desc txdesc; u32 word; u32 reg; - u32 old_reg; int type; int index; + int i; /* - * During each loop we will compare the freshly read - * STA_CSR4 register value with the value read from - * the previous loop. If the 2 values are equal then - * we should stop processing because the chance is - * quite big that the device has been unplugged and - * we risk going into an endless loop. + * TX_STA_FIFO is a stack of X entries, hence read TX_STA_FIFO + * at most X times and also stop processing once the TX_STA_FIFO_VALID + * flag is not set anymore. + * + * The legacy drivers use X=TX_RING_SIZE but state in a comment + * that the TX_STA_FIFO stack has a size of 16. We stick to our + * tx ring size for now. */ - old_reg = 0; - - while (1) { + for (i = 0; i < TX_ENTRIES; i++) { rt2x00pci_register_read(rt2x00dev, STA_CSR4, ®); if (!rt2x00_get_field32(reg, STA_CSR4_VALID)) break; - if (old_reg == reg) - break; - old_reg = reg; - /* * Skip this entry when it contains an invalid * queue identication number. @@ -2130,6 +2128,13 @@ static void rt61pci_txdone(struct rt2x00_dev *rt2x00dev) } txdesc.retry = rt2x00_get_field32(reg, STA_CSR4_RETRY_COUNT); + /* + * the frame was retried at least once + * -> hw used fallback rates + */ + if (txdesc.retry) + __set_bit(TXDONE_FALLBACK, &txdesc.flags); + rt2x00pci_txdone(entry, &txdesc); } } @@ -2587,6 +2592,18 @@ static int rt61pci_probe_hw_mode(struct rt2x00_dev *rt2x00dev) EEPROM_MAC_ADDR_0)); /* + * As rt61 has a global fallback table we cannot specify + * more then one tx rate per frame but since the hw will + * try several rates (based on the fallback table) we should + * still initialize max_rates to the maximum number of rates + * we are going to try. Otherwise mac80211 will truncate our + * reported tx rates and the rc algortihm will end up with + * incorrect data. + */ + rt2x00dev->hw->max_rates = 7; + rt2x00dev->hw->max_rate_tries = 1; + + /* * Initialize hw_mode information. */ spec->supported_bands = SUPPORT_BAND_2GHZ; |