diff options
Diffstat (limited to 'drivers/net/wireless/zd1211rw/zd_chip.h')
| -rw-r--r-- | drivers/net/wireless/zd1211rw/zd_chip.h | 158 |
1 files changed, 90 insertions, 68 deletions
diff --git a/drivers/net/wireless/zd1211rw/zd_chip.h b/drivers/net/wireless/zd1211rw/zd_chip.h index a4e3cee9b59..b07569e391e 100644 --- a/drivers/net/wireless/zd1211rw/zd_chip.h +++ b/drivers/net/wireless/zd1211rw/zd_chip.h @@ -18,7 +18,6 @@ #ifndef _ZD_CHIP_H #define _ZD_CHIP_H -#include "zd_types.h" #include "zd_rf.h" #include "zd_usb.h" @@ -27,6 +26,37 @@ * adds a processor for handling the USB protocol. */ +/* Address space */ +enum { + /* CONTROL REGISTERS */ + CR_START = 0x9000, + + + /* FIRMWARE */ + FW_START = 0xee00, + + + /* EEPROM */ + E2P_START = 0xf800, + E2P_LEN = 0x800, + + /* EEPROM layout */ + E2P_LOAD_CODE_LEN = 0xe, /* base 0xf800 */ + E2P_LOAD_VECT_LEN = 0x9, /* base 0xf80e */ + /* E2P_DATA indexes into this */ + E2P_DATA_LEN = 0x7e, /* base 0xf817 */ + E2P_BOOT_CODE_LEN = 0x760, /* base 0xf895 */ + E2P_INTR_VECT_LEN = 0xb, /* base 0xfff5 */ + + /* Some precomputed offsets into the EEPROM */ + E2P_DATA_OFFSET = E2P_LOAD_CODE_LEN + E2P_LOAD_VECT_LEN, + E2P_BOOT_CODE_OFFSET = E2P_DATA_OFFSET + E2P_DATA_LEN, +}; + +#define CTL_REG(offset) ((zd_addr_t)(CR_START + (offset))) +#define E2P_DATA(offset) ((zd_addr_t)(E2P_START + E2P_DATA_OFFSET + (offset))) +#define FWRAW_DATA(offset) ((zd_addr_t)(FW_START + (offset))) + /* 8-bit hardware registers */ #define CR0 CTL_REG(0x0000) #define CR1 CTL_REG(0x0004) @@ -302,7 +332,7 @@ #define CR_MAX_PHY_REG 255 -/* Taken from the ZYDAS driver, not all of them are relevant for the ZSD1211 +/* Taken from the ZYDAS driver, not all of them are relevant for the ZD1211 * driver. */ @@ -594,81 +624,71 @@ /* * Upper 16 bit contains the regulatory domain. */ -#define E2P_SUBID E2P_REG(0x00) -#define E2P_POD E2P_REG(0x02) -#define E2P_MAC_ADDR_P1 E2P_REG(0x04) -#define E2P_MAC_ADDR_P2 E2P_REG(0x06) -#define E2P_PWR_CAL_VALUE1 E2P_REG(0x08) -#define E2P_PWR_CAL_VALUE2 E2P_REG(0x0a) -#define E2P_PWR_CAL_VALUE3 E2P_REG(0x0c) -#define E2P_PWR_CAL_VALUE4 E2P_REG(0x0e) -#define E2P_PWR_INT_VALUE1 E2P_REG(0x10) -#define E2P_PWR_INT_VALUE2 E2P_REG(0x12) -#define E2P_PWR_INT_VALUE3 E2P_REG(0x14) -#define E2P_PWR_INT_VALUE4 E2P_REG(0x16) +#define E2P_SUBID E2P_DATA(0x00) +#define E2P_POD E2P_DATA(0x02) +#define E2P_MAC_ADDR_P1 E2P_DATA(0x04) +#define E2P_MAC_ADDR_P2 E2P_DATA(0x06) +#define E2P_PWR_CAL_VALUE1 E2P_DATA(0x08) +#define E2P_PWR_CAL_VALUE2 E2P_DATA(0x0a) +#define E2P_PWR_CAL_VALUE3 E2P_DATA(0x0c) +#define E2P_PWR_CAL_VALUE4 E2P_DATA(0x0e) +#define E2P_PWR_INT_VALUE1 E2P_DATA(0x10) +#define E2P_PWR_INT_VALUE2 E2P_DATA(0x12) +#define E2P_PWR_INT_VALUE3 E2P_DATA(0x14) +#define E2P_PWR_INT_VALUE4 E2P_DATA(0x16) /* Contains a bit for each allowed channel. It gives for Europe (ETSI 0x30) * also only 11 channels. */ -#define E2P_ALLOWED_CHANNEL E2P_REG(0x18) - -#define E2P_PHY_REG E2P_REG(0x1a) -#define E2P_DEVICE_VER E2P_REG(0x20) -#define E2P_36M_CAL_VALUE1 E2P_REG(0x28) -#define E2P_36M_CAL_VALUE2 E2P_REG(0x2a) -#define E2P_36M_CAL_VALUE3 E2P_REG(0x2c) -#define E2P_36M_CAL_VALUE4 E2P_REG(0x2e) -#define E2P_11A_INT_VALUE1 E2P_REG(0x30) -#define E2P_11A_INT_VALUE2 E2P_REG(0x32) -#define E2P_11A_INT_VALUE3 E2P_REG(0x34) -#define E2P_11A_INT_VALUE4 E2P_REG(0x36) -#define E2P_48M_CAL_VALUE1 E2P_REG(0x38) -#define E2P_48M_CAL_VALUE2 E2P_REG(0x3a) -#define E2P_48M_CAL_VALUE3 E2P_REG(0x3c) -#define E2P_48M_CAL_VALUE4 E2P_REG(0x3e) -#define E2P_48M_INT_VALUE1 E2P_REG(0x40) -#define E2P_48M_INT_VALUE2 E2P_REG(0x42) -#define E2P_48M_INT_VALUE3 E2P_REG(0x44) -#define E2P_48M_INT_VALUE4 E2P_REG(0x46) -#define E2P_54M_CAL_VALUE1 E2P_REG(0x48) /* ??? */ -#define E2P_54M_CAL_VALUE2 E2P_REG(0x4a) -#define E2P_54M_CAL_VALUE3 E2P_REG(0x4c) -#define E2P_54M_CAL_VALUE4 E2P_REG(0x4e) -#define E2P_54M_INT_VALUE1 E2P_REG(0x50) -#define E2P_54M_INT_VALUE2 E2P_REG(0x52) -#define E2P_54M_INT_VALUE3 E2P_REG(0x54) -#define E2P_54M_INT_VALUE4 E2P_REG(0x56) - -/* All 16 bit values */ -#define FW_FIRMWARE_VER FW_REG(0) -/* non-zero if USB high speed connection */ -#define FW_USB_SPEED FW_REG(1) -#define FW_FIX_TX_RATE FW_REG(2) -/* Seems to be able to control LEDs over the firmware */ -#define FW_LINK_STATUS FW_REG(3) -#define FW_SOFT_RESET FW_REG(4) -#define FW_FLASH_CHK FW_REG(5) +#define E2P_ALLOWED_CHANNEL E2P_DATA(0x18) + +#define E2P_PHY_REG E2P_DATA(0x1a) +#define E2P_DEVICE_VER E2P_DATA(0x20) +#define E2P_36M_CAL_VALUE1 E2P_DATA(0x28) +#define E2P_36M_CAL_VALUE2 E2P_DATA(0x2a) +#define E2P_36M_CAL_VALUE3 E2P_DATA(0x2c) +#define E2P_36M_CAL_VALUE4 E2P_DATA(0x2e) +#define E2P_11A_INT_VALUE1 E2P_DATA(0x30) +#define E2P_11A_INT_VALUE2 E2P_DATA(0x32) +#define E2P_11A_INT_VALUE3 E2P_DATA(0x34) +#define E2P_11A_INT_VALUE4 E2P_DATA(0x36) +#define E2P_48M_CAL_VALUE1 E2P_DATA(0x38) +#define E2P_48M_CAL_VALUE2 E2P_DATA(0x3a) +#define E2P_48M_CAL_VALUE3 E2P_DATA(0x3c) +#define E2P_48M_CAL_VALUE4 E2P_DATA(0x3e) +#define E2P_48M_INT_VALUE1 E2P_DATA(0x40) +#define E2P_48M_INT_VALUE2 E2P_DATA(0x42) +#define E2P_48M_INT_VALUE3 E2P_DATA(0x44) +#define E2P_48M_INT_VALUE4 E2P_DATA(0x46) +#define E2P_54M_CAL_VALUE1 E2P_DATA(0x48) /* ??? */ +#define E2P_54M_CAL_VALUE2 E2P_DATA(0x4a) +#define E2P_54M_CAL_VALUE3 E2P_DATA(0x4c) +#define E2P_54M_CAL_VALUE4 E2P_DATA(0x4e) +#define E2P_54M_INT_VALUE1 E2P_DATA(0x50) +#define E2P_54M_INT_VALUE2 E2P_DATA(0x52) +#define E2P_54M_INT_VALUE3 E2P_DATA(0x54) +#define E2P_54M_INT_VALUE4 E2P_DATA(0x56) + +/* This word contains the base address of the FW_REG_ registers below */ +#define FWRAW_REGS_ADDR FWRAW_DATA(0x1d) + +/* All 16 bit values, offset from the address in FWRAW_REGS_ADDR */ +enum { + FW_REG_FIRMWARE_VER = 0, + /* non-zero if USB high speed connection */ + FW_REG_USB_SPEED = 1, + FW_REG_FIX_TX_RATE = 2, + /* Seems to be able to control LEDs over the firmware */ + FW_REG_LED_LINK_STATUS = 3, + FW_REG_SOFT_RESET = 4, + FW_REG_FLASH_CHK = 5, +}; +/* Values for FW_LINK_STATUS */ #define FW_LINK_OFF 0x0 #define FW_LINK_TX 0x1 /* 0x2 - link led on? */ enum { - CR_BASE_OFFSET = 0x9000, - FW_START_OFFSET = 0xee00, - FW_BASE_ADDR_OFFSET = FW_START_OFFSET + 0x1d, - EEPROM_START_OFFSET = 0xf800, - EEPROM_SIZE = 0x800, /* words */ - LOAD_CODE_SIZE = 0xe, /* words */ - LOAD_VECT_SIZE = 0x10000 - 0xfff7, /* words */ - EEPROM_REGS_OFFSET = LOAD_CODE_SIZE + LOAD_VECT_SIZE, - EEPROM_REGS_SIZE = 0x7e, /* words */ - E2P_BASE_OFFSET = EEPROM_START_OFFSET + - EEPROM_REGS_OFFSET, -}; - -#define FW_REG_TABLE_ADDR USB_ADDR(FW_START_OFFSET + 0x1d) - -enum { /* indices for ofdm_cal_values */ OFDM_36M_INDEX = 0, OFDM_48M_INDEX = 1, @@ -679,6 +699,8 @@ struct zd_chip { struct zd_usb usb; struct zd_rf rf; struct mutex mutex; + /* Base address of FW_REG_ registers */ + zd_addr_t fw_regs_base; u8 e2p_mac[ETH_ALEN]; /* EepSetPoint in the vendor driver */ u8 pwr_cal_values[E2P_CHANNEL_COUNT]; |