diff options
Diffstat (limited to 'drivers/net/wireless')
| -rw-r--r-- | drivers/net/wireless/ath5k/dma.c | 2 | ||||
| -rw-r--r-- | drivers/net/wireless/atmel.c | 2 | ||||
| -rw-r--r-- | drivers/net/wireless/ipw2x00/ipw2100.c | 4 | ||||
| -rw-r--r-- | drivers/net/wireless/rt2x00/rt2x00crypto.c | 4 | ||||
| -rw-r--r-- | drivers/net/wireless/strip.c | 2 | ||||
| -rw-r--r-- | drivers/net/wireless/zd1211rw/zd_mac.c | 2 |
6 files changed, 8 insertions, 8 deletions
diff --git a/drivers/net/wireless/ath5k/dma.c b/drivers/net/wireless/ath5k/dma.c index 7e2b1a67e5d..b65b4feb2d2 100644 --- a/drivers/net/wireless/ath5k/dma.c +++ b/drivers/net/wireless/ath5k/dma.c @@ -594,7 +594,7 @@ int ath5k_hw_get_isr(struct ath5k_hw *ah, enum ath5k_int *interrupt_mask) * XXX: BMISS interrupts may occur after association. * I found this on 5210 code but it needs testing. If this is * true we should disable them before assoc and re-enable them - * after a successfull assoc + some jiffies. + * after a successful assoc + some jiffies. interrupt_mask &= ~AR5K_INT_BMISS; */ } diff --git a/drivers/net/wireless/atmel.c b/drivers/net/wireless/atmel.c index 350157fcd08..4223672c443 100644 --- a/drivers/net/wireless/atmel.c +++ b/drivers/net/wireless/atmel.c @@ -3836,7 +3836,7 @@ static int reset_atmel_card(struct net_device *dev) This routine is also responsible for initialising some hardware-specific fields in the atmel_private structure, including a copy of the firmware's hostinfo stucture - which is the route into the rest of the firmare datastructures. */ + which is the route into the rest of the firmware datastructures. */ struct atmel_private *priv = netdev_priv(dev); u8 configuration; diff --git a/drivers/net/wireless/ipw2x00/ipw2100.c b/drivers/net/wireless/ipw2x00/ipw2100.c index 1667065b86a..823c2bf5e31 100644 --- a/drivers/net/wireless/ipw2x00/ipw2100.c +++ b/drivers/net/wireless/ipw2x00/ipw2100.c @@ -1332,7 +1332,7 @@ static int ipw2100_power_cycle_adapter(struct ipw2100_priv *priv) IPW_AUX_HOST_RESET_REG_STOP_MASTER); /* Step 2. Wait for stop Master Assert - * (not more then 50us, otherwise ret error */ + * (not more than 50us, otherwise ret error */ i = 5; do { udelay(IPW_WAIT_RESET_MASTER_ASSERT_COMPLETE_DELAY); @@ -1830,7 +1830,7 @@ static void ipw2100_down(struct ipw2100_priv *priv) cancel_delayed_work(&priv->rf_kill); } - /* Kill the firmare hang check timer */ + /* Kill the firmware hang check timer */ if (!priv->stop_hang_check) { priv->stop_hang_check = 1; cancel_delayed_work(&priv->hang_check); diff --git a/drivers/net/wireless/rt2x00/rt2x00crypto.c b/drivers/net/wireless/rt2x00/rt2x00crypto.c index 37ad0d2fb64..aee9cba13eb 100644 --- a/drivers/net/wireless/rt2x00/rt2x00crypto.c +++ b/drivers/net/wireless/rt2x00/rt2x00crypto.c @@ -184,8 +184,8 @@ void rt2x00crypto_rx_insert_iv(struct sk_buff *skb, unsigned int align, * Make room for new data, note that we increase both * headsize and tailsize when required. The tailsize is * only needed when ICV data needs to be inserted and - * the padding is smaller then the ICV data. - * When alignment requirements is greater then the + * the padding is smaller than the ICV data. + * When alignment requirements is greater than the * ICV data we must trim the skb to the correct size * because we need to remove the extra bytes. */ diff --git a/drivers/net/wireless/strip.c b/drivers/net/wireless/strip.c index dd0de3a9ed4..7015f248055 100644 --- a/drivers/net/wireless/strip.c +++ b/drivers/net/wireless/strip.c @@ -236,7 +236,7 @@ struct strip { unsigned long tx_errors; /* Planned stuff */ unsigned long rx_dropped; /* No memory for skb */ unsigned long tx_dropped; /* When MTU change */ - unsigned long rx_over_errors; /* Frame bigger then STRIP buf. */ + unsigned long rx_over_errors; /* Frame bigger than STRIP buf. */ unsigned long pps_timer; /* Timer to determine pps */ unsigned long rx_pps_count; /* Counter to determine pps */ diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c index 9caa96a1358..a611ad85798 100644 --- a/drivers/net/wireless/zd1211rw/zd_mac.c +++ b/drivers/net/wireless/zd1211rw/zd_mac.c @@ -287,7 +287,7 @@ static void zd_op_stop(struct ieee80211_hw *hw) * @skb - a sk-buffer * @flags: extra flags to set in the TX status info * @ackssi: ACK signal strength - * @success - True for successfull transmission of the frame + * @success - True for successful transmission of the frame * * This information calls ieee80211_tx_status_irqsafe() if required by the * control information. It copies the control information into the status |