diff options
Diffstat (limited to 'drivers/net')
| -rw-r--r-- | drivers/net/ioc3-eth.c | 80 |
1 files changed, 60 insertions, 20 deletions
diff --git a/drivers/net/ioc3-eth.c b/drivers/net/ioc3-eth.c index 3ca1e8ece54..0834ef0eddb 100644 --- a/drivers/net/ioc3-eth.c +++ b/drivers/net/ioc3-eth.c @@ -48,6 +48,7 @@ #ifdef CONFIG_SERIAL_8250 #include <linux/serial_core.h> #include <linux/serial_8250.h> +#include <linux/serial_reg.h> #endif #include <linux/netdevice.h> @@ -1151,13 +1152,41 @@ static int ioc3_is_menet(struct pci_dev *pdev) * Also look in ip27-pci.c:pci_fixup_ioc3() for some comments on working * around ioc3 oddities in this respect. * - * The IOC3 serials use a 22MHz clock rate with an additional divider by 3. + * The IOC3 serials use a 22MHz clock rate with an additional divider which + * can be programmed in the SCR register if the DLAB bit is set. + * + * Register to interrupt zero because we share the interrupt with + * the serial driver which we don't properly support yet. + * + * Can't use UPF_IOREMAP as the whole of IOC3 resources have already been + * registered. */ +static void __devinit ioc3_8250_register(struct ioc3_uartregs __iomem *uart) +{ +#define COSMISC_CONSTANT 6 + + struct uart_port port = { + .irq = 0, + .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, + .iotype = UPIO_MEM, + .regshift = 0, + .uartclk = (22000000 << 1) / COSMISC_CONSTANT, + + .membase = (unsigned char __iomem *) uart, + .mapbase = (unsigned long) uart, + }; + unsigned char lcr; + + lcr = uart->iu_lcr; + uart->iu_lcr = lcr | UART_LCR_DLAB; + uart->iu_scr = COSMISC_CONSTANT, + uart->iu_lcr = lcr; + uart->iu_lcr; + serial8250_register_port(&port); +} static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3) { - struct uart_port port; - /* * We need to recognice and treat the fourth MENET serial as it * does not have an SuperIO chip attached to it, therefore attempting @@ -1171,24 +1200,35 @@ static void __devinit ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3) return; /* - * Register to interrupt zero because we share the interrupt with - * the serial driver which we don't properly support yet. - * - * Can't use UPF_IOREMAP as the whole of IOC3 resources have already - * been registered. + * Switch IOC3 to PIO mode. It probably already was but let's be + * paranoid */ - memset(&port, 0, sizeof(port)); - port.irq = 0; - port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; - port.iotype = UPIO_MEM; - port.regshift = 0; - port.uartclk = 22000000 / 3; - - port.membase = (unsigned char *) &ioc3->sregs.uarta; - serial8250_register_port(&port); - - port.membase = (unsigned char *) &ioc3->sregs.uartb; - serial8250_register_port(&port); + ioc3->gpcr_s = GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL; + ioc3->gpcr_s; + ioc3->gppr_6 = 0; + ioc3->gppr_6; + ioc3->gppr_7 = 0; + ioc3->gppr_7; + ioc3->sscr_a = ioc3->sscr_a & ~SSCR_DMA_EN; + ioc3->sscr_a; + ioc3->sscr_b = ioc3->sscr_b & ~SSCR_DMA_EN; + ioc3->sscr_b; + /* Disable all SA/B interrupts except for SA/B_INT in SIO_IEC. */ + ioc3->sio_iec &= ~ (SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL | + SIO_IR_SA_RX_HIGH | SIO_IR_SA_RX_TIMER | + SIO_IR_SA_DELTA_DCD | SIO_IR_SA_DELTA_CTS | + SIO_IR_SA_TX_EXPLICIT | SIO_IR_SA_MEMERR); + ioc3->sio_iec |= SIO_IR_SA_INT; + ioc3->sscr_a = 0; + ioc3->sio_iec &= ~ (SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL | + SIO_IR_SB_RX_HIGH | SIO_IR_SB_RX_TIMER | + SIO_IR_SB_DELTA_DCD | SIO_IR_SB_DELTA_CTS | + SIO_IR_SB_TX_EXPLICIT | SIO_IR_SB_MEMERR); + ioc3->sio_iec |= SIO_IR_SB_INT; + ioc3->sscr_b = 0; + + ioc3_8250_register(&ioc3->sregs.uarta); + ioc3_8250_register(&ioc3->sregs.uartb); } #endif |