diff options
Diffstat (limited to 'drivers/net')
144 files changed, 13274 insertions, 12158 deletions
diff --git a/drivers/net/3c59x.c b/drivers/net/3c59x.c index 7adff4d0960..b9eeadf01b7 100644 --- a/drivers/net/3c59x.c +++ b/drivers/net/3c59x.c @@ -813,10 +813,10 @@ static int vortex_suspend(struct pci_dev *pdev, pm_message_t state) if (netif_running(dev)) { netif_device_detach(dev); vortex_down(dev, 1); + disable_irq(dev->irq); } pci_save_state(pdev); pci_enable_wake(pdev, pci_choose_state(pdev, state), 0); - free_irq(dev->irq, dev); pci_disable_device(pdev); pci_set_power_state(pdev, pci_choose_state(pdev, state)); } @@ -839,18 +839,12 @@ static int vortex_resume(struct pci_dev *pdev) return err; } pci_set_master(pdev); - if (request_irq(dev->irq, vp->full_bus_master_rx ? - &boomerang_interrupt : &vortex_interrupt, IRQF_SHARED, dev->name, dev)) { - pr_warning("%s: Could not reserve IRQ %d\n", dev->name, dev->irq); - pci_disable_device(pdev); - return -EBUSY; - } if (netif_running(dev)) { err = vortex_up(dev); if (err) return err; - else - netif_device_attach(dev); + enable_irq(dev->irq); + netif_device_attach(dev); } } return 0; diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c index 462d9f59c53..83a1922e68e 100644 --- a/drivers/net/8139cp.c +++ b/drivers/net/8139cp.c @@ -87,7 +87,7 @@ /* These identify the driver base version and may not be removed. */ static char version[] = -KERN_INFO DRV_NAME ": 10/100 PCI Ethernet driver v" DRV_VERSION " (" DRV_RELDATE ")\n"; +DRV_NAME ": 10/100 PCI Ethernet driver v" DRV_VERSION " (" DRV_RELDATE ")\n"; MODULE_AUTHOR("Jeff Garzik <jgarzik@pobox.com>"); MODULE_DESCRIPTION("RealTek RTL-8139C+ series 10/100 PCI Ethernet driver"); diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 507569a4f23..2bea67c134f 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -1875,7 +1875,7 @@ config 68360_ENET config FEC bool "FEC ethernet controller (of ColdFire and some i.MX CPUs)" - depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 + depends on M523x || M527x || M5272 || M528x || M520x || M532x || MACH_MX27 || ARCH_MX35 || ARCH_MX25 help Say Y here if you want to use the built-in 10/100 Fast ethernet controller on some Motorola ColdFire and Freescale i.MX processors. @@ -1934,6 +1934,15 @@ config XILINX_EMACLITE help This driver supports the 10/100 Ethernet Lite from Xilinx. +config BCM63XX_ENET + tristate "Broadcom 63xx internal mac support" + depends on BCM63XX + select MII + select PHYLIB + help + This driver supports the ethernet MACs in the Broadcom 63xx + MIPS chipset family (BCM63XX). + source "drivers/net/fs_enet/Kconfig" endif # NET_ETHERNET diff --git a/drivers/net/Makefile b/drivers/net/Makefile index 99ae6d7fe6a..ae8cd30f13d 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -137,6 +137,7 @@ obj-$(CONFIG_B44) += b44.o obj-$(CONFIG_FORCEDETH) += forcedeth.o obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o obj-$(CONFIG_AX88796) += ax88796.o +obj-$(CONFIG_BCM63XX_ENET) += bcm63xx_enet.o obj-$(CONFIG_TSI108_ETH) += tsi108_eth.o obj-$(CONFIG_MV643XX_ETH) += mv643xx_eth.o diff --git a/drivers/net/arcnet/arc-rawmode.c b/drivers/net/arcnet/arc-rawmode.c index 646dfc5f50c..8ea9c7545c1 100644 --- a/drivers/net/arcnet/arc-rawmode.c +++ b/drivers/net/arcnet/arc-rawmode.c @@ -123,7 +123,6 @@ static void rx(struct net_device *dev, int bufnum, BUGLVL(D_SKB) arcnet_dump_skb(dev, skb, "rx"); skb->protocol = cpu_to_be16(ETH_P_ARCNET); -; netif_rx(skb); } diff --git a/drivers/net/arcnet/capmode.c b/drivers/net/arcnet/capmode.c index 083e21094b2..66bcbbb6bab 100644 --- a/drivers/net/arcnet/capmode.c +++ b/drivers/net/arcnet/capmode.c @@ -149,7 +149,6 @@ static void rx(struct net_device *dev, int bufnum, BUGLVL(D_SKB) arcnet_dump_skb(dev, skb, "rx"); skb->protocol = cpu_to_be16(ETH_P_ARCNET); -; netif_rx(skb); } diff --git a/drivers/net/atl1c/atl1c_main.c b/drivers/net/atl1c/atl1c_main.c index be2c6cfe6e8..1372e9a99f5 100644 --- a/drivers/net/atl1c/atl1c_main.c +++ b/drivers/net/atl1c/atl1c_main.c @@ -2296,7 +2296,7 @@ static int atl1c_suspend(struct pci_dev *pdev, pm_message_t state) u32 ctrl; u32 mac_ctrl_data; u32 master_ctrl_data; - u32 wol_ctrl_data; + u32 wol_ctrl_data = 0; u16 mii_bmsr_data; u16 save_autoneg_advertised; u16 mii_intr_status_data; diff --git a/drivers/net/atl1e/atl1e.h b/drivers/net/atl1e/atl1e.h index ba48220df16..490d3b38e0c 100644 --- a/drivers/net/atl1e/atl1e.h +++ b/drivers/net/atl1e/atl1e.h @@ -377,10 +377,19 @@ struct atl1e_hw { */ struct atl1e_tx_buffer { struct sk_buff *skb; + u16 flags; +#define ATL1E_TX_PCIMAP_SINGLE 0x0001 +#define ATL1E_TX_PCIMAP_PAGE 0x0002 +#define ATL1E_TX_PCIMAP_TYPE_MASK 0x0003 u16 length; dma_addr_t dma; }; +#define ATL1E_SET_PCIMAP_TYPE(tx_buff, type) do { \ + ((tx_buff)->flags) &= ~ATL1E_TX_PCIMAP_TYPE_MASK; \ + ((tx_buff)->flags) |= (type); \ + } while (0) + struct atl1e_rx_page { dma_addr_t dma; /* receive rage DMA address */ u8 *addr; /* receive rage virtual address */ diff --git a/drivers/net/atl1e/atl1e_main.c b/drivers/net/atl1e/atl1e_main.c index 69b830f4b68..955da733c2a 100644 --- a/drivers/net/atl1e/atl1e_main.c +++ b/drivers/net/atl1e/atl1e_main.c @@ -635,7 +635,11 @@ static void atl1e_clean_tx_ring(struct atl1e_adapter *adapter) for (index = 0; index < ring_count; index++) { tx_buffer = &tx_ring->tx_buffer[index]; if (tx_buffer->dma) { - pci_unmap_page(pdev, tx_buffer->dma, + if (tx_buffer->flags & ATL1E_TX_PCIMAP_SINGLE) + pci_unmap_single(pdev, tx_buffer->dma, + tx_buffer->length, PCI_DMA_TODEVICE); + else if (tx_buffer->flags & ATL1E_TX_PCIMAP_PAGE) + pci_unmap_page(pdev, tx_buffer->dma, tx_buffer->length, PCI_DMA_TODEVICE); tx_buffer->dma = 0; } @@ -1220,7 +1224,11 @@ static bool atl1e_clean_tx_irq(struct atl1e_adapter *adapter) while (next_to_clean != hw_next_to_clean) { tx_buffer = &tx_ring->tx_buffer[next_to_clean]; if (tx_buffer->dma) { - pci_unmap_page(adapter->pdev, tx_buffer->dma, + if (tx_buffer->flags & ATL1E_TX_PCIMAP_SINGLE) + pci_unmap_single(adapter->pdev, tx_buffer->dma, + tx_buffer->length, PCI_DMA_TODEVICE); + else if (tx_buffer->flags & ATL1E_TX_PCIMAP_PAGE) + pci_unmap_page(adapter->pdev, tx_buffer->dma, tx_buffer->length, PCI_DMA_TODEVICE); tx_buffer->dma = 0; } @@ -1741,6 +1749,7 @@ static void atl1e_tx_map(struct atl1e_adapter *adapter, tx_buffer->length = map_len; tx_buffer->dma = pci_map_single(adapter->pdev, skb->data, hdr_len, PCI_DMA_TODEVICE); + ATL1E_SET_PCIMAP_TYPE(tx_buffer, ATL1E_TX_PCIMAP_SINGLE); mapped_len += map_len; use_tpd->buffer_addr = cpu_to_le64(tx_buffer->dma); use_tpd->word2 = (use_tpd->word2 & (~TPD_BUFLEN_MASK)) | @@ -1766,6 +1775,7 @@ static void atl1e_tx_map(struct atl1e_adapter *adapter, tx_buffer->dma = pci_map_single(adapter->pdev, skb->data + mapped_len, map_len, PCI_DMA_TODEVICE); + ATL1E_SET_PCIMAP_TYPE(tx_buffer, ATL1E_TX_PCIMAP_SINGLE); mapped_len += map_len; use_tpd->buffer_addr = cpu_to_le64(tx_buffer->dma); use_tpd->word2 = (use_tpd->word2 & (~TPD_BUFLEN_MASK)) | @@ -1801,6 +1811,7 @@ static void atl1e_tx_map(struct atl1e_adapter *adapter, (i * MAX_TX_BUF_LEN), tx_buffer->length, PCI_DMA_TODEVICE); + ATL1E_SET_PCIMAP_TYPE(tx_buffer, ATL1E_TX_PCIMAP_PAGE); use_tpd->buffer_addr = cpu_to_le64(tx_buffer->dma); use_tpd->word2 = (use_tpd->word2 & (~TPD_BUFLEN_MASK)) | ((cpu_to_le32(tx_buffer->length) & diff --git a/drivers/net/b44.c b/drivers/net/b44.c index 0189dcd36f3..e046943ef29 100644 --- a/drivers/net/b44.c +++ b/drivers/net/b44.c @@ -847,23 +847,22 @@ static int b44_poll(struct napi_struct *napi, int budget) { struct b44 *bp = container_of(napi, struct b44, napi); int work_done; + unsigned long flags; - spin_lock_irq(&bp->lock); + spin_lock_irqsave(&bp->lock, flags); if (bp->istat & (ISTAT_TX | ISTAT_TO)) { /* spin_lock(&bp->tx_lock); */ b44_tx(bp); /* spin_unlock(&bp->tx_lock); */ } - spin_unlock_irq(&bp->lock); + spin_unlock_irqrestore(&bp->lock, flags); work_done = 0; if (bp->istat & ISTAT_RX) work_done += b44_rx(bp, budget); if (bp->istat & ISTAT_ERRORS) { - unsigned long flags; - spin_lock_irqsave(&bp->lock, flags); b44_halt(bp); b44_init_rings(bp); diff --git a/drivers/net/bcm63xx_enet.c b/drivers/net/bcm63xx_enet.c new file mode 100644 index 00000000000..09d270913c5 --- /dev/null +++ b/drivers/net/bcm63xx_enet.c @@ -0,0 +1,1971 @@ +/* + * Driver for BCM963xx builtin Ethernet mac + * + * Copyright (C) 2008 Maxime Bizon <mbizon@freebox.fr> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#include <linux/init.h> +#include <linux/module.h> +#include <linux/clk.h> +#include <linux/etherdevice.h> +#include <linux/delay.h> +#include <linux/ethtool.h> +#include <linux/crc32.h> +#include <linux/err.h> +#include <linux/dma-mapping.h> +#include <linux/platform_device.h> +#include <linux/if_vlan.h> + +#include <bcm63xx_dev_enet.h> +#include "bcm63xx_enet.h" + +static char bcm_enet_driver_name[] = "bcm63xx_enet"; +static char bcm_enet_driver_version[] = "1.0"; + +static int copybreak __read_mostly = 128; +module_param(copybreak, int, 0); +MODULE_PARM_DESC(copybreak, "Receive copy threshold"); + +/* io memory shared between all devices */ +static void __iomem *bcm_enet_shared_base; + +/* + * io helpers to access mac registers + */ +static inline u32 enet_readl(struct bcm_enet_priv *priv, u32 off) +{ + return bcm_readl(priv->base + off); +} + +static inline void enet_writel(struct bcm_enet_priv *priv, + u32 val, u32 off) +{ + bcm_writel(val, priv->base + off); +} + +/* + * io helpers to access shared registers + */ +static inline u32 enet_dma_readl(struct bcm_enet_priv *priv, u32 off) +{ + return bcm_readl(bcm_enet_shared_base + off); +} + +static inline void enet_dma_writel(struct bcm_enet_priv *priv, + u32 val, u32 off) +{ + bcm_writel(val, bcm_enet_shared_base + off); +} + +/* + * write given data into mii register and wait for transfer to end + * with timeout (average measured transfer time is 25us) + */ +static int do_mdio_op(struct bcm_enet_priv *priv, unsigned int data) +{ + int limit; + + /* make sure mii interrupt status is cleared */ + enet_writel(priv, ENET_IR_MII, ENET_IR_REG); + + enet_writel(priv, data, ENET_MIIDATA_REG); + wmb(); + + /* busy wait on mii interrupt bit, with timeout */ + limit = 1000; + do { + if (enet_readl(priv, ENET_IR_REG) & ENET_IR_MII) + break; + udelay(1); + } while (limit-- >= 0); + + return (limit < 0) ? 1 : 0; +} + +/* + * MII internal read callback + */ +static int bcm_enet_mdio_read(struct bcm_enet_priv *priv, int mii_id, + int regnum) +{ + u32 tmp, val; + + tmp = regnum << ENET_MIIDATA_REG_SHIFT; + tmp |= 0x2 << ENET_MIIDATA_TA_SHIFT; + tmp |= mii_id << ENET_MIIDATA_PHYID_SHIFT; + tmp |= ENET_MIIDATA_OP_READ_MASK; + + if (do_mdio_op(priv, tmp)) + return -1; + + val = enet_readl(priv, ENET_MIIDATA_REG); + val &= 0xffff; + return val; +} + +/* + * MII internal write callback + */ +static int bcm_enet_mdio_write(struct bcm_enet_priv *priv, int mii_id, + int regnum, u16 value) +{ + u32 tmp; + + tmp = (value & 0xffff) << ENET_MIIDATA_DATA_SHIFT; + tmp |= 0x2 << ENET_MIIDATA_TA_SHIFT; + tmp |= regnum << ENET_MIIDATA_REG_SHIFT; + tmp |= mii_id << ENET_MIIDATA_PHYID_SHIFT; + tmp |= ENET_MIIDATA_OP_WRITE_MASK; + + (void)do_mdio_op(priv, tmp); + return 0; +} + +/* + * MII read callback from phylib + */ +static int bcm_enet_mdio_read_phylib(struct mii_bus *bus, int mii_id, + int regnum) +{ + return bcm_enet_mdio_read(bus->priv, mii_id, regnum); +} + +/* + * MII write callback from phylib + */ +static int bcm_enet_mdio_write_phylib(struct mii_bus *bus, int mii_id, + int regnum, u16 value) +{ + return bcm_enet_mdio_write(bus->priv, mii_id, regnum, value); +} + +/* + * MII read callback from mii core + */ +static int bcm_enet_mdio_read_mii(struct net_device *dev, int mii_id, + int regnum) +{ + return bcm_enet_mdio_read(netdev_priv(dev), mii_id, regnum); +} + +/* + * MII write callback from mii core + */ +static void bcm_enet_mdio_write_mii(struct net_device *dev, int mii_id, + int regnum, int value) +{ + bcm_enet_mdio_write(netdev_priv(dev), mii_id, regnum, value); +} + +/* + * refill rx queue + */ +static int bcm_enet_refill_rx(struct net_device *dev) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + + while (priv->rx_desc_count < priv->rx_ring_size) { + struct bcm_enet_desc *desc; + struct sk_buff *skb; + dma_addr_t p; + int desc_idx; + u32 len_stat; + + desc_idx = priv->rx_dirty_desc; + desc = &priv->rx_desc_cpu[desc_idx]; + + if (!priv->rx_skb[desc_idx]) { + skb = netdev_alloc_skb(dev, priv->rx_skb_size); + if (!skb) + break; + priv->rx_skb[desc_idx] = skb; + + p = dma_map_single(&priv->pdev->dev, skb->data, + priv->rx_skb_size, + DMA_FROM_DEVICE); + desc->address = p; + } + + len_stat = priv->rx_skb_size << DMADESC_LENGTH_SHIFT; + len_stat |= DMADESC_OWNER_MASK; + if (priv->rx_dirty_desc == priv->rx_ring_size - 1) { + len_stat |= DMADESC_WRAP_MASK; + priv->rx_dirty_desc = 0; + } else { + priv->rx_dirty_desc++; + } + wmb(); + desc->len_stat = len_stat; + + priv->rx_desc_count++; + + /* tell dma engine we allocated one buffer */ + enet_dma_writel(priv, 1, ENETDMA_BUFALLOC_REG(priv->rx_chan)); + } + + /* If rx ring is still empty, set a timer to try allocating + * again at a later time. */ + if (priv->rx_desc_count == 0 && netif_running(dev)) { + dev_warn(&priv->pdev->dev, "unable to refill rx ring\n"); + priv->rx_timeout.expires = jiffies + HZ; + add_timer(&priv->rx_timeout); + } + + return 0; +} + +/* + * timer callback to defer refill rx queue in case we're OOM + */ +static void bcm_enet_refill_rx_timer(unsigned long data) +{ + struct net_device *dev; + struct bcm_enet_priv *priv; + + dev = (struct net_device *)data; + priv = netdev_priv(dev); + + spin_lock(&priv->rx_lock); + bcm_enet_refill_rx((struct net_device *)data); + spin_unlock(&priv->rx_lock); +} + +/* + * extract packet from rx queue + */ +static int bcm_enet_receive_queue(struct net_device *dev, int budget) +{ + struct bcm_enet_priv *priv; + struct device *kdev; + int processed; + + priv = netdev_priv(dev); + kdev = &priv->pdev->dev; + processed = 0; + + /* don't scan ring further than number of refilled + * descriptor */ + if (budget > priv->rx_desc_count) + budget = priv->rx_desc_count; + + do { + struct bcm_enet_desc *desc; + struct sk_buff *skb; + int desc_idx; + u32 len_stat; + unsigned int len; + + desc_idx = priv->rx_curr_desc; + desc = &priv->rx_desc_cpu[desc_idx]; + + /* make sure we actually read the descriptor status at + * each loop */ + rmb(); + + len_stat = desc->len_stat; + + /* break if dma ownership belongs to hw */ + if (len_stat & DMADESC_OWNER_MASK) + break; + + processed++; + priv->rx_curr_desc++; + if (priv->rx_curr_desc == priv->rx_ring_size) + priv->rx_curr_desc = 0; + priv->rx_desc_count--; + + /* if the packet does not have start of packet _and_ + * end of packet flag set, then just recycle it */ + if ((len_stat & DMADESC_ESOP_MASK) != DMADESC_ESOP_MASK) { + priv->stats.rx_dropped++; + continue; + } + + /* recycle packet if it's marked as bad */ + if (unlikely(len_stat & DMADESC_ERR_MASK)) { + priv->stats.rx_errors++; + + if (len_stat & DMADESC_OVSIZE_MASK) + priv->stats.rx_length_errors++; + if (len_stat & DMADESC_CRC_MASK) + priv->stats.rx_crc_errors++; + if (len_stat & DMADESC_UNDER_MASK) + priv->stats.rx_frame_errors++; + if (len_stat & DMADESC_OV_MASK) + priv->stats.rx_fifo_errors++; + continue; + } + + /* valid packet */ + skb = priv->rx_skb[desc_idx]; + len = (len_stat & DMADESC_LENGTH_MASK) >> DMADESC_LENGTH_SHIFT; + /* don't include FCS */ + len -= 4; + + if (len < copybreak) { + struct sk_buff *nskb; + + nskb = netdev_alloc_skb(dev, len + NET_IP_ALIGN); + if (!nskb) { + /* forget packet, just rearm desc */ + priv->stats.rx_dropped++; + continue; + } + + /* since we're copying the data, we can align + * them properly */ + skb_reserve(nskb, NET_IP_ALIGN); + dma_sync_single_for_cpu(kdev, desc->address, + len, DMA_FROM_DEVICE); + memcpy(nskb->data, skb->data, len); + dma_sync_single_for_device(kdev, desc->address, + len, DMA_FROM_DEVICE); + skb = nskb; + } else { + dma_unmap_single(&priv->pdev->dev, desc->address, + priv->rx_skb_size, DMA_FROM_DEVICE); + priv->rx_skb[desc_idx] = NULL; + } + + skb_put(skb, len); + skb->dev = dev; + skb->protocol = eth_type_trans(skb, dev); + priv->stats.rx_packets++; + priv->stats.rx_bytes += len; + dev->last_rx = jiffies; + netif_receive_skb(skb); + + } while (--budget > 0); + + if (processed || !priv->rx_desc_count) { + bcm_enet_refill_rx(dev); + + /* kick rx dma */ + enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, + ENETDMA_CHANCFG_REG(priv->rx_chan)); + } + + return processed; +} + + +/* + * try to or force reclaim of transmitted buffers + */ +static int bcm_enet_tx_reclaim(struct net_device *dev, int force) +{ + struct bcm_enet_priv *priv; + int released; + + priv = netdev_priv(dev); + released = 0; + + while (priv->tx_desc_count < priv->tx_ring_size) { + struct bcm_enet_desc *desc; + struct sk_buff *skb; + + /* We run in a bh and fight against start_xmit, which + * is called with bh disabled */ + spin_lock(&priv->tx_lock); + + desc = &priv->tx_desc_cpu[priv->tx_dirty_desc]; + + if (!force && (desc->len_stat & DMADESC_OWNER_MASK)) { + spin_unlock(&priv->tx_lock); + break; + } + + /* ensure other field of the descriptor were not read + * before we checked ownership */ + rmb(); + + skb = priv->tx_skb[priv->tx_dirty_desc]; + priv->tx_skb[priv->tx_dirty_desc] = NULL; + dma_unmap_single(&priv->pdev->dev, desc->address, skb->len, + DMA_TO_DEVICE); + + priv->tx_dirty_desc++; + if (priv->tx_dirty_desc == priv->tx_ring_size) + priv->tx_dirty_desc = 0; + priv->tx_desc_count++; + + spin_unlock(&priv->tx_lock); + + if (desc->len_stat & DMADESC_UNDER_MASK) + priv->stats.tx_errors++; + + dev_kfree_skb(skb); + released++; + } + + if (netif_queue_stopped(dev) && released) + netif_wake_queue(dev); + + return released; +} + +/* + * poll func, called by network core + */ +static int bcm_enet_poll(struct napi_struct *napi, int budget) +{ + struct bcm_enet_priv *priv; + struct net_device *dev; + int tx_work_done, rx_work_done; + + priv = container_of(napi, struct bcm_enet_priv, napi); + dev = priv->net_dev; + + /* ack interrupts */ + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IR_REG(priv->rx_chan)); + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IR_REG(priv->tx_chan)); + + /* reclaim sent skb */ + tx_work_done = bcm_enet_tx_reclaim(dev, 0); + + spin_lock(&priv->rx_lock); + rx_work_done = bcm_enet_receive_queue(dev, budget); + spin_unlock(&priv->rx_lock); + + if (rx_work_done >= budget || tx_work_done > 0) { + /* rx/tx queue is not yet empty/clean */ + return rx_work_done; + } + + /* no more packet in rx/tx queue, remove device from poll + * queue */ + napi_complete(napi); + + /* restore rx/tx interrupt */ + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IRMASK_REG(priv->rx_chan)); + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IRMASK_REG(priv->tx_chan)); + + return rx_work_done; +} + +/* + * mac interrupt handler + */ +static irqreturn_t bcm_enet_isr_mac(int irq, void *dev_id) +{ + struct net_device *dev; + struct bcm_enet_priv *priv; + u32 stat; + + dev = dev_id; + priv = netdev_priv(dev); + + stat = enet_readl(priv, ENET_IR_REG); + if (!(stat & ENET_IR_MIB)) + return IRQ_NONE; + + /* clear & mask interrupt */ + enet_writel(priv, ENET_IR_MIB, ENET_IR_REG); + enet_writel(priv, 0, ENET_IRMASK_REG); + + /* read mib registers in workqueue */ + schedule_work(&priv->mib_update_task); + + return IRQ_HANDLED; +} + +/* + * rx/tx dma interrupt handler + */ +static irqreturn_t bcm_enet_isr_dma(int irq, void *dev_id) +{ + struct net_device *dev; + struct bcm_enet_priv *priv; + + dev = dev_id; + priv = netdev_priv(dev); + + /* mask rx/tx interrupts */ + enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); + enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); + + napi_schedule(&priv->napi); + + return IRQ_HANDLED; +} + +/* + * tx request callback + */ +static int bcm_enet_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct bcm_enet_priv *priv; + struct bcm_enet_desc *desc; + u32 len_stat; + int ret; + + priv = netdev_priv(dev); + + /* lock against tx reclaim */ + spin_lock(&priv->tx_lock); + + /* make sure the tx hw queue is not full, should not happen + * since we stop queue before it's the case */ + if (unlikely(!priv->tx_desc_count)) { + netif_stop_queue(dev); + dev_err(&priv->pdev->dev, "xmit called with no tx desc " + "available?\n"); + ret = NETDEV_TX_BUSY; + goto out_unlock; + } + + /* point to the next available desc */ + desc = &priv->tx_desc_cpu[priv->tx_curr_desc]; + priv->tx_skb[priv->tx_curr_desc] = skb; + + /* fill descriptor */ + desc->address = dma_map_single(&priv->pdev->dev, skb->data, skb->len, + DMA_TO_DEVICE); + + len_stat = (skb->len << DMADESC_LENGTH_SHIFT) & DMADESC_LENGTH_MASK; + len_stat |= DMADESC_ESOP_MASK | + DMADESC_APPEND_CRC | + DMADESC_OWNER_MASK; + + priv->tx_curr_desc++; + if (priv->tx_curr_desc == priv->tx_ring_size) { + priv->tx_curr_desc = 0; + len_stat |= DMADESC_WRAP_MASK; + } + priv->tx_desc_count--; + + /* dma might be already polling, make sure we update desc + * fields in correct order */ + wmb(); + desc->len_stat = len_stat; + wmb(); + + /* kick tx dma */ + enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, + ENETDMA_CHANCFG_REG(priv->tx_chan)); + + /* stop queue if no more desc available */ + if (!priv->tx_desc_count) + netif_stop_queue(dev); + + priv->stats.tx_bytes += skb->len; + priv->stats.tx_packets++; + dev->trans_start = jiffies; + ret = NETDEV_TX_OK; + +out_unlock: + spin_unlock(&priv->tx_lock); + return ret; +} + +/* + * Change the interface's mac address. + */ +static int bcm_enet_set_mac_address(struct net_device *dev, void *p) +{ + struct bcm_enet_priv *priv; + struct sockaddr *addr = p; + u32 val; + + priv = netdev_priv(dev); + memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN); + + /* use perfect match register 0 to store my mac address */ + val = (dev->dev_addr[2] << 24) | (dev->dev_addr[3] << 16) | + (dev->dev_addr[4] << 8) | dev->dev_addr[5]; + enet_writel(priv, val, ENET_PML_REG(0)); + + val = (dev->dev_addr[0] << 8 | dev->dev_addr[1]); + val |= ENET_PMH_DATAVALID_MASK; + enet_writel(priv, val, ENET_PMH_REG(0)); + + return 0; +} + +/* + * Change rx mode (promiscous/allmulti) and update multicast list + */ +static void bcm_enet_set_multicast_list(struct net_device *dev) +{ + struct bcm_enet_priv *priv; + struct dev_mc_list *mc_list; + u32 val; + int i; + + priv = netdev_priv(dev); + + val = enet_readl(priv, ENET_RXCFG_REG); + + if (dev->flags & IFF_PROMISC) + val |= ENET_RXCFG_PROMISC_MASK; + else + val &= ~ENET_RXCFG_PROMISC_MASK; + + /* only 3 perfect match registers left, first one is used for + * own mac address */ + if ((dev->flags & IFF_ALLMULTI) || dev->mc_count > 3) + val |= ENET_RXCFG_ALLMCAST_MASK; + else + val &= ~ENET_RXCFG_ALLMCAST_MASK; + + /* no need to set perfect match registers if we catch all + * multicast */ + if (val & ENET_RXCFG_ALLMCAST_MASK) { + enet_writel(priv, val, ENET_RXCFG_REG); + return; + } + + for (i = 0, mc_list = dev->mc_list; + (mc_list != NULL) && (i < dev->mc_count) && (i < 3); + i++, mc_list = mc_list->next) { + u8 *dmi_addr; + u32 tmp; + + /* filter non ethernet address */ + if (mc_list->dmi_addrlen != 6) + continue; + + /* update perfect match registers */ + dmi_addr = mc_list->dmi_addr; + tmp = (dmi_addr[2] << 24) | (dmi_addr[3] << 16) | + (dmi_addr[4] << 8) | dmi_addr[5]; + enet_writel(priv, tmp, ENET_PML_REG(i + 1)); + + tmp = (dmi_addr[0] << 8 | dmi_addr[1]); + tmp |= ENET_PMH_DATAVALID_MASK; + enet_writel(priv, tmp, ENET_PMH_REG(i + 1)); + } + + for (; i < 3; i++) { + enet_writel(priv, 0, ENET_PML_REG(i + 1)); + enet_writel(priv, 0, ENET_PMH_REG(i + 1)); + } + + enet_writel(priv, val, ENET_RXCFG_REG); +} + +/* + * set mac duplex parameters + */ +static void bcm_enet_set_duplex(struct bcm_enet_priv *priv, int fullduplex) +{ + u32 val; + + val = enet_readl(priv, ENET_TXCTL_REG); + if (fullduplex) + val |= ENET_TXCTL_FD_MASK; + else + val &= ~ENET_TXCTL_FD_MASK; + enet_writel(priv, val, ENET_TXCTL_REG); +} + +/* + * set mac flow control parameters + */ +static void bcm_enet_set_flow(struct bcm_enet_priv *priv, int rx_en, int tx_en) +{ + u32 val; + + /* rx flow control (pause frame handling) */ + val = enet_readl(priv, ENET_RXCFG_REG); + if (rx_en) + val |= ENET_RXCFG_ENFLOW_MASK; + else + val &= ~ENET_RXCFG_ENFLOW_MASK; + enet_writel(priv, val, ENET_RXCFG_REG); + + /* tx flow control (pause frame generation) */ + val = enet_dma_readl(priv, ENETDMA_CFG_REG); + if (tx_en) + val |= ENETDMA_CFG_FLOWCH_MASK(priv->rx_chan); + else + val &= ~ENETDMA_CFG_FLOWCH_MASK(priv->rx_chan); + enet_dma_writel(priv, val, ENETDMA_CFG_REG); +} + +/* + * link changed callback (from phylib) + */ +static void bcm_enet_adjust_phy_link(struct net_device *dev) +{ + struct bcm_enet_priv *priv; + struct phy_device *phydev; + int status_changed; + + priv = netdev_priv(dev); + phydev = priv->phydev; + status_changed = 0; + + if (priv->old_link != phydev->link) { + status_changed = 1; + priv->old_link = phydev->link; + } + + /* reflect duplex change in mac configuration */ + if (phydev->link && phydev->duplex != priv->old_duplex) { + bcm_enet_set_duplex(priv, + (phydev->duplex == DUPLEX_FULL) ? 1 : 0); + status_changed = 1; + priv->old_duplex = phydev->duplex; + } + + /* enable flow control if remote advertise it (trust phylib to + * check that duplex is full */ + if (phydev->link && phydev->pause != priv->old_pause) { + int rx_pause_en, tx_pause_en; + + if (phydev->pause) { + /* pause was advertised by lpa and us */ + rx_pause_en = 1; + tx_pause_en = 1; + } else if (!priv->pause_auto) { + /* pause setting overrided by user */ + rx_pause_en = priv->pause_rx; + tx_pause_en = priv->pause_tx; + } else { + rx_pause_en = 0; + tx_pause_en = 0; + } + + bcm_enet_set_flow(priv, rx_pause_en, tx_pause_en); + status_changed = 1; + priv->old_pause = phydev->pause; + } + + if (status_changed) { + pr_info("%s: link %s", dev->name, phydev->link ? + "UP" : "DOWN"); + if (phydev->link) + pr_cont(" - %d/%s - flow control %s", phydev->speed, + DUPLEX_FULL == phydev->duplex ? "full" : "half", + phydev->pause == 1 ? "rx&tx" : "off"); + + pr_cont("\n"); + } +} + +/* + * link changed callback (if phylib is not used) + */ +static void bcm_enet_adjust_link(struct net_device *dev) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + bcm_enet_set_duplex(priv, priv->force_duplex_full); + bcm_enet_set_flow(priv, priv->pause_rx, priv->pause_tx); + netif_carrier_on(dev); + + pr_info("%s: link forced UP - %d/%s - flow control %s/%s\n", + dev->name, + priv->force_speed_100 ? 100 : 10, + priv->force_duplex_full ? "full" : "half", + priv->pause_rx ? "rx" : "off", + priv->pause_tx ? "tx" : "off"); +} + +/* + * open callback, allocate dma rings & buffers and start rx operation + */ +static int bcm_enet_open(struct net_device *dev) +{ + struct bcm_enet_priv *priv; + struct sockaddr addr; + struct device *kdev; + struct phy_device *phydev; + int i, ret; + unsigned int size; + char phy_id[MII_BUS_ID_SIZE + 3]; + void *p; + u32 val; + + priv = netdev_priv(dev); + kdev = &priv->pdev->dev; + + if (priv->has_phy) { + /* connect to PHY */ + snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, + priv->mac_id ? "1" : "0", priv->phy_id); + + phydev = phy_connect(dev, phy_id, &bcm_enet_adjust_phy_link, 0, + PHY_INTERFACE_MODE_MII); + + if (IS_ERR(phydev)) { + dev_err(kdev, "could not attach to PHY\n"); + return PTR_ERR(phydev); + } + + /* mask with MAC supported features */ + phydev->supported &= (SUPPORTED_10baseT_Half | + SUPPORTED_10baseT_Full | + SUPPORTED_100baseT_Half | + SUPPORTED_100baseT_Full | + SUPPORTED_Autoneg | + SUPPORTED_Pause | + SUPPORTED_MII); + phydev->advertising = phydev->supported; + + if (priv->pause_auto && priv->pause_rx && priv->pause_tx) + phydev->advertising |= SUPPORTED_Pause; + else + phydev->advertising &= ~SUPPORTED_Pause; + + dev_info(kdev, "attached PHY at address %d [%s]\n", + phydev->addr, phydev->drv->name); + + priv->old_link = 0; + priv->old_duplex = -1; + priv->old_pause = -1; + priv->phydev = phydev; + } + + /* mask all interrupts and request them */ + enet_writel(priv, 0, ENET_IRMASK_REG); + enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); + enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); + + ret = request_irq(dev->irq, bcm_enet_isr_mac, 0, dev->name, dev); + if (ret) + goto out_phy_disconnect; + + ret = request_irq(priv->irq_rx, bcm_enet_isr_dma, + IRQF_SAMPLE_RANDOM | IRQF_DISABLED, dev->name, dev); + if (ret) + goto out_freeirq; + + ret = request_irq(priv->irq_tx, bcm_enet_isr_dma, + IRQF_DISABLED, dev->name, dev); + if (ret) + goto out_freeirq_rx; + + /* initialize perfect match registers */ + for (i = 0; i < 4; i++) { + enet_writel(priv, 0, ENET_PML_REG(i)); + enet_writel(priv, 0, ENET_PMH_REG(i)); + } + + /* write device mac address */ + memcpy(addr.sa_data, dev->dev_addr, ETH_ALEN); + bcm_enet_set_mac_address(dev, &addr); + + /* allocate rx dma ring */ + size = priv->rx_ring_size * sizeof(struct bcm_enet_desc); + p = dma_alloc_coherent(kdev, size, &priv->rx_desc_dma, GFP_KERNEL); + if (!p) { + dev_err(kdev, "cannot allocate rx ring %u\n", size); + ret = -ENOMEM; + goto out_freeirq_tx; + } + + memset(p, 0, size); + priv->rx_desc_alloc_size = size; + priv->rx_desc_cpu = p; + + /* allocate tx dma ring */ + size = priv->tx_ring_size * sizeof(struct bcm_enet_desc); + p = dma_alloc_coherent(kdev, size, &priv->tx_desc_dma, GFP_KERNEL); + if (!p) { + dev_err(kdev, "cannot allocate tx ring\n"); + ret = -ENOMEM; + goto out_free_rx_ring; + } + + memset(p, 0, size); + priv->tx_desc_alloc_size = size; + priv->tx_desc_cpu = p; + + priv->tx_skb = kzalloc(sizeof(struct sk_buff *) * priv->tx_ring_size, + GFP_KERNEL); + if (!priv->tx_skb) { + dev_err(kdev, "cannot allocate rx skb queue\n"); + ret = -ENOMEM; + goto out_free_tx_ring; + } + + priv->tx_desc_count = priv->tx_ring_size; + priv->tx_dirty_desc = 0; + priv->tx_curr_desc = 0; + spin_lock_init(&priv->tx_lock); + + /* init & fill rx ring with skbs */ + priv->rx_skb = kzalloc(sizeof(struct sk_buff *) * priv->rx_ring_size, + GFP_KERNEL); + if (!priv->rx_skb) { + dev_err(kdev, "cannot allocate rx skb queue\n"); + ret = -ENOMEM; + goto out_free_tx_skb; + } + + priv->rx_desc_count = 0; + priv->rx_dirty_desc = 0; + priv->rx_curr_desc = 0; + + /* initialize flow control buffer allocation */ + enet_dma_writel(priv, ENETDMA_BUFALLOC_FORCE_MASK | 0, + ENETDMA_BUFALLOC_REG(priv->rx_chan)); + + if (bcm_enet_refill_rx(dev)) { + dev_err(kdev, "cannot allocate rx skb queue\n"); + ret = -ENOMEM; + goto out; + } + + /* write rx & tx ring addresses */ + enet_dma_writel(priv, priv->rx_desc_dma, + ENETDMA_RSTART_REG(priv->rx_chan)); + enet_dma_writel(priv, priv->tx_desc_dma, + ENETDMA_RSTART_REG(priv->tx_chan)); + + /* clear remaining state ram for rx & tx channel */ + enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->rx_chan)); + enet_dma_writel(priv, 0, ENETDMA_SRAM2_REG(priv->tx_chan)); + enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->rx_chan)); + enet_dma_writel(priv, 0, ENETDMA_SRAM3_REG(priv->tx_chan)); + enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->rx_chan)); + enet_dma_writel(priv, 0, ENETDMA_SRAM4_REG(priv->tx_chan)); + + /* set max rx/tx length */ + enet_writel(priv, priv->hw_mtu, ENET_RXMAXLEN_REG); + enet_writel(priv, priv->hw_mtu, ENET_TXMAXLEN_REG); + + /* set dma maximum burst len */ + enet_dma_writel(priv, BCMENET_DMA_MAXBURST, + ENETDMA_MAXBURST_REG(priv->rx_chan)); + enet_dma_writel(priv, BCMENET_DMA_MAXBURST, + ENETDMA_MAXBURST_REG(priv->tx_chan)); + + /* set correct transmit fifo watermark */ + enet_writel(priv, BCMENET_TX_FIFO_TRESH, ENET_TXWMARK_REG); + + /* set flow control low/high threshold to 1/3 / 2/3 */ + val = priv->rx_ring_size / 3; + enet_dma_writel(priv, val, ENETDMA_FLOWCL_REG(priv->rx_chan)); + val = (priv->rx_ring_size * 2) / 3; + enet_dma_writel(priv, val, ENETDMA_FLOWCH_REG(priv->rx_chan)); + + /* all set, enable mac and interrupts, start dma engine and + * kick rx dma channel */ + wmb(); + enet_writel(priv, ENET_CTL_ENABLE_MASK, ENET_CTL_REG); + enet_dma_writel(priv, ENETDMA_CFG_EN_MASK, ENETDMA_CFG_REG); + enet_dma_writel(priv, ENETDMA_CHANCFG_EN_MASK, + ENETDMA_CHANCFG_REG(priv->rx_chan)); + + /* watch "mib counters about to overflow" interrupt */ + enet_writel(priv, ENET_IR_MIB, ENET_IR_REG); + enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG); + + /* watch "packet transferred" interrupt in rx and tx */ + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IR_REG(priv->rx_chan)); + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IR_REG(priv->tx_chan)); + + /* make sure we enable napi before rx interrupt */ + napi_enable(&priv->napi); + + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IRMASK_REG(priv->rx_chan)); + enet_dma_writel(priv, ENETDMA_IR_PKTDONE_MASK, + ENETDMA_IRMASK_REG(priv->tx_chan)); + + if (priv->has_phy) + phy_start(priv->phydev); + else + bcm_enet_adjust_link(dev); + + netif_start_queue(dev); + return 0; + +out: + for (i = 0; i < priv->rx_ring_size; i++) { + struct bcm_enet_desc *desc; + + if (!priv->rx_skb[i]) + continue; + + desc = &priv->rx_desc_cpu[i]; + dma_unmap_single(kdev, desc->address, priv->rx_skb_size, + DMA_FROM_DEVICE); + kfree_skb(priv->rx_skb[i]); + } + kfree(priv->rx_skb); + +out_free_tx_skb: + kfree(priv->tx_skb); + +out_free_tx_ring: + dma_free_coherent(kdev, priv->tx_desc_alloc_size, + priv->tx_desc_cpu, priv->tx_desc_dma); + +out_free_rx_ring: + dma_free_coherent(kdev, priv->rx_desc_alloc_size, + priv->rx_desc_cpu, priv->rx_desc_dma); + +out_freeirq_tx: + free_irq(priv->irq_tx, dev); + +out_freeirq_rx: + free_irq(priv->irq_rx, dev); + +out_freeirq: + free_irq(dev->irq, dev); + +out_phy_disconnect: + phy_disconnect(priv->phydev); + + return ret; +} + +/* + * disable mac + */ +static void bcm_enet_disable_mac(struct bcm_enet_priv *priv) +{ + int limit; + u32 val; + + val = enet_readl(priv, ENET_CTL_REG); + val |= ENET_CTL_DISABLE_MASK; + enet_writel(priv, val, ENET_CTL_REG); + + limit = 1000; + do { + u32 val; + + val = enet_readl(priv, ENET_CTL_REG); + if (!(val & ENET_CTL_DISABLE_MASK)) + break; + udelay(1); + } while (limit--); +} + +/* + * disable dma in given channel + */ +static void bcm_enet_disable_dma(struct bcm_enet_priv *priv, int chan) +{ + int limit; + + enet_dma_writel(priv, 0, ENETDMA_CHANCFG_REG(chan)); + + limit = 1000; + do { + u32 val; + + val = enet_dma_readl(priv, ENETDMA_CHANCFG_REG(chan)); + if (!(val & ENETDMA_CHANCFG_EN_MASK)) + break; + udelay(1); + } while (limit--); +} + +/* + * stop callback + */ +static int bcm_enet_stop(struct net_device *dev) +{ + struct bcm_enet_priv *priv; + struct device *kdev; + int i; + + priv = netdev_priv(dev); + kdev = &priv->pdev->dev; + + netif_stop_queue(dev); + napi_disable(&priv->napi); + if (priv->has_phy) + phy_stop(priv->phydev); + del_timer_sync(&priv->rx_timeout); + + /* mask all interrupts */ + enet_writel(priv, 0, ENET_IRMASK_REG); + enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->rx_chan)); + enet_dma_writel(priv, 0, ENETDMA_IRMASK_REG(priv->tx_chan)); + + /* make sure no mib update is scheduled */ + flush_scheduled_work(); + + /* disable dma & mac */ + bcm_enet_disable_dma(priv, priv->tx_chan); + bcm_enet_disable_dma(priv, priv->rx_chan); + bcm_enet_disable_mac(priv); + + /* force reclaim of all tx buffers */ + bcm_enet_tx_reclaim(dev, 1); + + /* free the rx skb ring */ + for (i = 0; i < priv->rx_ring_size; i++) { + struct bcm_enet_desc *desc; + + if (!priv->rx_skb[i]) + continue; + + desc = &priv->rx_desc_cpu[i]; + dma_unmap_single(kdev, desc->address, priv->rx_skb_size, + DMA_FROM_DEVICE); + kfree_skb(priv->rx_skb[i]); + } + + /* free remaining allocated memory */ + kfree(priv->rx_skb); + kfree(priv->tx_skb); + dma_free_coherent(kdev, priv->rx_desc_alloc_size, + priv->rx_desc_cpu, priv->rx_desc_dma); + dma_free_coherent(kdev, priv->tx_desc_alloc_size, + priv->tx_desc_cpu, priv->tx_desc_dma); + free_irq(priv->irq_tx, dev); + free_irq(priv->irq_rx, dev); + free_irq(dev->irq, dev); + + /* release phy */ + if (priv->has_phy) { + phy_disconnect(priv->phydev); + priv->phydev = NULL; + } + + return 0; +} + +/* + * core request to return device rx/tx stats + */ +static struct net_device_stats *bcm_enet_get_stats(struct net_device *dev) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + return &priv->stats; +} + +/* + * ethtool callbacks + */ +struct bcm_enet_stats { + char stat_string[ETH_GSTRING_LEN]; + int sizeof_stat; + int stat_offset; + int mib_reg; +}; + +#define GEN_STAT(m) sizeof(((struct bcm_enet_priv *)0)->m), \ + offsetof(struct bcm_enet_priv, m) + +static const struct bcm_enet_stats bcm_enet_gstrings_stats[] = { + { "rx_packets", GEN_STAT(stats.rx_packets), -1 }, + { "tx_packets", GEN_STAT(stats.tx_packets), -1 }, + { "rx_bytes", GEN_STAT(stats.rx_bytes), -1 }, + { "tx_bytes", GEN_STAT(stats.tx_bytes), -1 }, + { "rx_errors", GEN_STAT(stats.rx_errors), -1 }, + { "tx_errors", GEN_STAT(stats.tx_errors), -1 }, + { "rx_dropped", GEN_STAT(stats.rx_dropped), -1 }, + { "tx_dropped", GEN_STAT(stats.tx_dropped), -1 }, + + { "rx_good_octets", GEN_STAT(mib.rx_gd_octets), ETH_MIB_RX_GD_OCTETS}, + { "rx_good_pkts", GEN_STAT(mib.rx_gd_pkts), ETH_MIB_RX_GD_PKTS }, + { "rx_broadcast", GEN_STAT(mib.rx_brdcast), ETH_MIB_RX_BRDCAST }, + { "rx_multicast", GEN_STAT(mib.rx_mult), ETH_MIB_RX_MULT }, + { "rx_64_octets", GEN_STAT(mib.rx_64), ETH_MIB_RX_64 }, + { "rx_65_127_oct", GEN_STAT(mib.rx_65_127), ETH_MIB_RX_65_127 }, + { "rx_128_255_oct", GEN_STAT(mib.rx_128_255), ETH_MIB_RX_128_255 }, + { "rx_256_511_oct", GEN_STAT(mib.rx_256_511), ETH_MIB_RX_256_511 }, + { "rx_512_1023_oct", GEN_STAT(mib.rx_512_1023), ETH_MIB_RX_512_1023 }, + { "rx_1024_max_oct", GEN_STAT(mib.rx_1024_max), ETH_MIB_RX_1024_MAX }, + { "rx_jabber", GEN_STAT(mib.rx_jab), ETH_MIB_RX_JAB }, + { "rx_oversize", GEN_STAT(mib.rx_ovr), ETH_MIB_RX_OVR }, + { "rx_fragment", GEN_STAT(mib.rx_frag), ETH_MIB_RX_FRAG }, + { "rx_dropped", GEN_STAT(mib.rx_drop), ETH_MIB_RX_DROP }, + { "rx_crc_align", GEN_STAT(mib.rx_crc_align), ETH_MIB_RX_CRC_ALIGN }, + { "rx_undersize", GEN_STAT(mib.rx_und), ETH_MIB_RX_UND }, + { "rx_crc", GEN_STAT(mib.rx_crc), ETH_MIB_RX_CRC }, + { "rx_align", GEN_STAT(mib.rx_align), ETH_MIB_RX_ALIGN }, + { "rx_symbol_error", GEN_STAT(mib.rx_sym), ETH_MIB_RX_SYM }, + { "rx_pause", GEN_STAT(mib.rx_pause), ETH_MIB_RX_PAUSE }, + { "rx_control", GEN_STAT(mib.rx_cntrl), ETH_MIB_RX_CNTRL }, + + { "tx_good_octets", GEN_STAT(mib.tx_gd_octets), ETH_MIB_TX_GD_OCTETS }, + { "tx_good_pkts", GEN_STAT(mib.tx_gd_pkts), ETH_MIB_TX_GD_PKTS }, + { "tx_broadcast", GEN_STAT(mib.tx_brdcast), ETH_MIB_TX_BRDCAST }, + { "tx_multicast", GEN_STAT(mib.tx_mult), ETH_MIB_TX_MULT }, + { "tx_64_oct", GEN_STAT(mib.tx_64), ETH_MIB_TX_64 }, + { "tx_65_127_oct", GEN_STAT(mib.tx_65_127), ETH_MIB_TX_65_127 }, + { "tx_128_255_oct", GEN_STAT(mib.tx_128_255), ETH_MIB_TX_128_255 }, + { "tx_256_511_oct", GEN_STAT(mib.tx_256_511), ETH_MIB_TX_256_511 }, + { "tx_512_1023_oct", GEN_STAT(mib.tx_512_1023), ETH_MIB_TX_512_1023}, + { "tx_1024_max_oct", GEN_STAT(mib.tx_1024_max), ETH_MIB_TX_1024_MAX }, + { "tx_jabber", GEN_STAT(mib.tx_jab), ETH_MIB_TX_JAB }, + { "tx_oversize", GEN_STAT(mib.tx_ovr), ETH_MIB_TX_OVR }, + { "tx_fragment", GEN_STAT(mib.tx_frag), ETH_MIB_TX_FRAG }, + { "tx_underrun", GEN_STAT(mib.tx_underrun), ETH_MIB_TX_UNDERRUN }, + { "tx_collisions", GEN_STAT(mib.tx_col), ETH_MIB_TX_COL }, + { "tx_single_collision", GEN_STAT(mib.tx_1_col), ETH_MIB_TX_1_COL }, + { "tx_multiple_collision", GEN_STAT(mib.tx_m_col), ETH_MIB_TX_M_COL }, + { "tx_excess_collision", GEN_STAT(mib.tx_ex_col), ETH_MIB_TX_EX_COL }, + { "tx_late_collision", GEN_STAT(mib.tx_late), ETH_MIB_TX_LATE }, + { "tx_deferred", GEN_STAT(mib.tx_def), ETH_MIB_TX_DEF }, + { "tx_carrier_sense", GEN_STAT(mib.tx_crs), ETH_MIB_TX_CRS }, + { "tx_pause", GEN_STAT(mib.tx_pause), ETH_MIB_TX_PAUSE }, + +}; + +#define BCM_ENET_STATS_LEN \ + (sizeof(bcm_enet_gstrings_stats) / sizeof(struct bcm_enet_stats)) + +static const u32 unused_mib_regs[] = { + ETH_MIB_TX_ALL_OCTETS, + ETH_MIB_TX_ALL_PKTS, + ETH_MIB_RX_ALL_OCTETS, + ETH_MIB_RX_ALL_PKTS, +}; + + +static void bcm_enet_get_drvinfo(struct net_device *netdev, + struct ethtool_drvinfo *drvinfo) +{ + strncpy(drvinfo->driver, bcm_enet_driver_name, 32); + strncpy(drvinfo->version, bcm_enet_driver_version, 32); + strncpy(drvinfo->fw_version, "N/A", 32); + strncpy(drvinfo->bus_info, "bcm63xx", 32); + drvinfo->n_stats = BCM_ENET_STATS_LEN; +} + +static int bcm_enet_get_stats_count(struct net_device *netdev) +{ + return BCM_ENET_STATS_LEN; +} + +static void bcm_enet_get_strings(struct net_device *netdev, + u32 stringset, u8 *data) +{ + int i; + + switch (stringset) { + case ETH_SS_STATS: + for (i = 0; i < BCM_ENET_STATS_LEN; i++) { + memcpy(data + i * ETH_GSTRING_LEN, + bcm_enet_gstrings_stats[i].stat_string, + ETH_GSTRING_LEN); + } + break; + } +} + +static void update_mib_counters(struct bcm_enet_priv *priv) +{ + int i; + + for (i = 0; i < BCM_ENET_STATS_LEN; i++) { + const struct bcm_enet_stats *s; + u32 val; + char *p; + + s = &bcm_enet_gstrings_stats[i]; + if (s->mib_reg == -1) + continue; + + val = enet_readl(priv, ENET_MIB_REG(s->mib_reg)); + p = (char *)priv + s->stat_offset; + + if (s->sizeof_stat == sizeof(u64)) + *(u64 *)p += val; + else + *(u32 *)p += val; + } + + /* also empty unused mib counters to make sure mib counter + * overflow interrupt is cleared */ + for (i = 0; i < ARRAY_SIZE(unused_mib_regs); i++) + (void)enet_readl(priv, ENET_MIB_REG(unused_mib_regs[i])); +} + +static void bcm_enet_update_mib_counters_defer(struct work_struct *t) +{ + struct bcm_enet_priv *priv; + + priv = container_of(t, struct bcm_enet_priv, mib_update_task); + mutex_lock(&priv->mib_update_lock); + update_mib_counters(priv); + mutex_unlock(&priv->mib_update_lock); + + /* reenable mib interrupt */ + if (netif_running(priv->net_dev)) + enet_writel(priv, ENET_IR_MIB, ENET_IRMASK_REG); +} + +static void bcm_enet_get_ethtool_stats(struct net_device *netdev, + struct ethtool_stats *stats, + u64 *data) +{ + struct bcm_enet_priv *priv; + int i; + + priv = netdev_priv(netdev); + + mutex_lock(&priv->mib_update_lock); + update_mib_counters(priv); + + for (i = 0; i < BCM_ENET_STATS_LEN; i++) { + const struct bcm_enet_stats *s; + char *p; + + s = &bcm_enet_gstrings_stats[i]; + p = (char *)priv + s->stat_offset; + data[i] = (s->sizeof_stat == sizeof(u64)) ? + *(u64 *)p : *(u32 *)p; + } + mutex_unlock(&priv->mib_update_lock); +} + +static int bcm_enet_get_settings(struct net_device *dev, + struct ethtool_cmd *cmd) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + + cmd->maxrxpkt = 0; + cmd->maxtxpkt = 0; + + if (priv->has_phy) { + if (!priv->phydev) + return -ENODEV; + return phy_ethtool_gset(priv->phydev, cmd); + } else { + cmd->autoneg = 0; + cmd->speed = (priv->force_speed_100) ? SPEED_100 : SPEED_10; + cmd->duplex = (priv->force_duplex_full) ? + DUPLEX_FULL : DUPLEX_HALF; + cmd->supported = ADVERTISED_10baseT_Half | + ADVERTISED_10baseT_Full | + ADVERTISED_100baseT_Half | + ADVERTISED_100baseT_Full; + cmd->advertising = 0; + cmd->port = PORT_MII; + cmd->transceiver = XCVR_EXTERNAL; + } + return 0; +} + +static int bcm_enet_set_settings(struct net_device *dev, + struct ethtool_cmd *cmd) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + if (priv->has_phy) { + if (!priv->phydev) + return -ENODEV; + return phy_ethtool_sset(priv->phydev, cmd); + } else { + + if (cmd->autoneg || + (cmd->speed != SPEED_100 && cmd->speed != SPEED_10) || + cmd->port != PORT_MII) + return -EINVAL; + + priv->force_speed_100 = (cmd->speed == SPEED_100) ? 1 : 0; + priv->force_duplex_full = (cmd->duplex == DUPLEX_FULL) ? 1 : 0; + + if (netif_running(dev)) + bcm_enet_adjust_link(dev); + return 0; + } +} + +static void bcm_enet_get_ringparam(struct net_device *dev, + struct ethtool_ringparam *ering) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + + /* rx/tx ring is actually only limited by memory */ + ering->rx_max_pending = 8192; + ering->tx_max_pending = 8192; + ering->rx_mini_max_pending = 0; + ering->rx_jumbo_max_pending = 0; + ering->rx_pending = priv->rx_ring_size; + ering->tx_pending = priv->tx_ring_size; +} + +static int bcm_enet_set_ringparam(struct net_device *dev, + struct ethtool_ringparam *ering) +{ + struct bcm_enet_priv *priv; + int was_running; + + priv = netdev_priv(dev); + + was_running = 0; + if (netif_running(dev)) { + bcm_enet_stop(dev); + was_running = 1; + } + + priv->rx_ring_size = ering->rx_pending; + priv->tx_ring_size = ering->tx_pending; + + if (was_running) { + int err; + + err = bcm_enet_open(dev); + if (err) + dev_close(dev); + else + bcm_enet_set_multicast_list(dev); + } + return 0; +} + +static void bcm_enet_get_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *ecmd) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + ecmd->autoneg = priv->pause_auto; + ecmd->rx_pause = priv->pause_rx; + ecmd->tx_pause = priv->pause_tx; +} + +static int bcm_enet_set_pauseparam(struct net_device *dev, + struct ethtool_pauseparam *ecmd) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + + if (priv->has_phy) { + if (ecmd->autoneg && (ecmd->rx_pause != ecmd->tx_pause)) { + /* asymetric pause mode not supported, + * actually possible but integrated PHY has RO + * asym_pause bit */ + return -EINVAL; + } + } else { + /* no pause autoneg on direct mii connection */ + if (ecmd->autoneg) + return -EINVAL; + } + + priv->pause_auto = ecmd->autoneg; + priv->pause_rx = ecmd->rx_pause; + priv->pause_tx = ecmd->tx_pause; + + return 0; +} + +static struct ethtool_ops bcm_enet_ethtool_ops = { + .get_strings = bcm_enet_get_strings, + .get_stats_count = bcm_enet_get_stats_count, + .get_ethtool_stats = bcm_enet_get_ethtool_stats, + .get_settings = bcm_enet_get_settings, + .set_settings = bcm_enet_set_settings, + .get_drvinfo = bcm_enet_get_drvinfo, + .get_link = ethtool_op_get_link, + .get_ringparam = bcm_enet_get_ringparam, + .set_ringparam = bcm_enet_set_ringparam, + .get_pauseparam = bcm_enet_get_pauseparam, + .set_pauseparam = bcm_enet_set_pauseparam, +}; + +static int bcm_enet_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) +{ + struct bcm_enet_priv *priv; + + priv = netdev_priv(dev); + if (priv->has_phy) { + if (!priv->phydev) + return -ENODEV; + return phy_mii_ioctl(priv->phydev, if_mii(rq), cmd); + } else { + struct mii_if_info mii; + + mii.dev = dev; + mii.mdio_read = bcm_enet_mdio_read_mii; + mii.mdio_write = bcm_enet_mdio_write_mii; + mii.phy_id = 0; + mii.phy_id_mask = 0x3f; + mii.reg_num_mask = 0x1f; + return generic_mii_ioctl(&mii, if_mii(rq), cmd, NULL); + } +} + +/* + * calculate actual hardware mtu + */ +static int compute_hw_mtu(struct bcm_enet_priv *priv, int mtu) +{ + int actual_mtu; + + actual_mtu = mtu; + + /* add ethernet header + vlan tag size */ + actual_mtu += VLAN_ETH_HLEN; + + if (actual_mtu < 64 || actual_mtu > BCMENET_MAX_MTU) + return -EINVAL; + + /* + * setup maximum size before we get overflow mark in + * descriptor, note that this will not prevent reception of + * big frames, they will be split into multiple buffers + * anyway + */ + priv->hw_mtu = actual_mtu; + + /* + * align rx buffer size to dma burst len, account FCS since + * it's appended + */ + priv->rx_skb_size = ALIGN(actual_mtu + ETH_FCS_LEN, + BCMENET_DMA_MAXBURST * 4); + return 0; +} + +/* + * adjust mtu, can't be called while device is running + */ +static int bcm_enet_change_mtu(struct net_device *dev, int new_mtu) +{ + int ret; + + if (netif_running(dev)) + return -EBUSY; + + ret = compute_hw_mtu(netdev_priv(dev), new_mtu); + if (ret) + return ret; + dev->mtu = new_mtu; + return 0; +} + +/* + * preinit hardware to allow mii operation while device is down + */ +static void bcm_enet_hw_preinit(struct bcm_enet_priv *priv) +{ + u32 val; + int limit; + + /* make sure mac is disabled */ + bcm_enet_disable_mac(priv); + + /* soft reset mac */ + val = ENET_CTL_SRESET_MASK; + enet_writel(priv, val, ENET_CTL_REG); + wmb(); + + limit = 1000; + do { + val = enet_readl(priv, ENET_CTL_REG); + if (!(val & ENET_CTL_SRESET_MASK)) + break; + udelay(1); + } while (limit--); + + /* select correct mii interface */ + val = enet_readl(priv, ENET_CTL_REG); + if (priv->use_external_mii) + val |= ENET_CTL_EPHYSEL_MASK; + else + val &= ~ENET_CTL_EPHYSEL_MASK; + enet_writel(priv, val, ENET_CTL_REG); + + /* turn on mdc clock */ + enet_writel(priv, (0x1f << ENET_MIISC_MDCFREQDIV_SHIFT) | + ENET_MIISC_PREAMBLEEN_MASK, ENET_MIISC_REG); + + /* set mib counters to self-clear when read */ + val = enet_readl(priv, ENET_MIBCTL_REG); + val |= ENET_MIBCTL_RDCLEAR_MASK; + enet_writel(priv, val, ENET_MIBCTL_REG); +} + +static const struct net_device_ops bcm_enet_ops = { + .ndo_open = bcm_enet_open, + .ndo_stop = bcm_enet_stop, + .ndo_start_xmit = bcm_enet_start_xmit, + .ndo_get_stats = bcm_enet_get_stats, + .ndo_set_mac_address = bcm_enet_set_mac_address, + .ndo_set_multicast_list = bcm_enet_set_multicast_list, + .ndo_do_ioctl = bcm_enet_ioctl, + .ndo_change_mtu = bcm_enet_change_mtu, +#ifdef CONFIG_NET_POLL_CONTROLLER + .ndo_poll_controller = bcm_enet_netpoll, +#endif +}; + +/* + * allocate netdevice, request register memory and register device. + */ +static int __devinit bcm_enet_probe(struct platform_device *pdev) +{ + struct bcm_enet_priv *priv; + struct net_device *dev; + struct bcm63xx_enet_platform_data *pd; + struct resource *res_mem, *res_irq, *res_irq_rx, *res_irq_tx; + struct mii_bus *bus; + const char *clk_name; + unsigned int iomem_size; + int i, ret; + + /* stop if shared driver failed, assume driver->probe will be + * called in the same order we register devices (correct ?) */ + if (!bcm_enet_shared_base) + return -ENODEV; + + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + res_irq = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + res_irq_rx = platform_get_resource(pdev, IORESOURCE_IRQ, 1); + res_irq_tx = platform_get_resource(pdev, IORESOURCE_IRQ, 2); + if (!res_mem || !res_irq || !res_irq_rx || !res_irq_tx) + return -ENODEV; + + ret = 0; + dev = alloc_etherdev(sizeof(*priv)); + if (!dev) + return -ENOMEM; + priv = netdev_priv(dev); + memset(priv, 0, sizeof(*priv)); + + ret = compute_hw_mtu(priv, dev->mtu); + if (ret) + goto out; + + iomem_size = res_mem->end - res_mem->start + 1; + if (!request_mem_region(res_mem->start, iomem_size, "bcm63xx_enet")) { + ret = -EBUSY; + goto out; + } + + priv->base = ioremap(res_mem->start, iomem_size); + if (priv->base == NULL) { + ret = -ENOMEM; + goto out_release_mem; + } + dev->irq = priv->irq = res_irq->start; + priv->irq_rx = res_irq_rx->start; + priv->irq_tx = res_irq_tx->start; + priv->mac_id = pdev->id; + + /* get rx & tx dma channel id for this mac */ + if (priv->mac_id == 0) { + priv->rx_chan = 0; + priv->tx_chan = 1; + clk_name = "enet0"; + } else { + priv->rx_chan = 2; + priv->tx_chan = 3; + clk_name = "enet1"; + } + + priv->mac_clk = clk_get(&pdev->dev, clk_name); + if (IS_ERR(priv->mac_clk)) { + ret = PTR_ERR(priv->mac_clk); + goto out_unmap; + } + clk_enable(priv->mac_clk); + + /* initialize default and fetch platform data */ + priv->rx_ring_size = BCMENET_DEF_RX_DESC; + priv->tx_ring_size = BCMENET_DEF_TX_DESC; + + pd = pdev->dev.platform_data; + if (pd) { + memcpy(dev->dev_addr, pd->mac_addr, ETH_ALEN); + priv->has_phy = pd->has_phy; + priv->phy_id = pd->phy_id; + priv->has_phy_interrupt = pd->has_phy_interrupt; + priv->phy_interrupt = pd->phy_interrupt; + priv->use_external_mii = !pd->use_internal_phy; + priv->pause_auto = pd->pause_auto; + priv->pause_rx = pd->pause_rx; + priv->pause_tx = pd->pause_tx; + priv->force_duplex_full = pd->force_duplex_full; + priv->force_speed_100 = pd->force_speed_100; + } + + if (priv->mac_id == 0 && priv->has_phy && !priv->use_external_mii) { + /* using internal PHY, enable clock */ + priv->phy_clk = clk_get(&pdev->dev, "ephy"); + if (IS_ERR(priv->phy_clk)) { + ret = PTR_ERR(priv->phy_clk); + priv->phy_clk = NULL; + goto out_put_clk_mac; + } + clk_enable(priv->phy_clk); + } + + /* do minimal hardware init to be able to probe mii bus */ + bcm_enet_hw_preinit(priv); + + /* MII bus registration */ + if (priv->has_phy) { + + priv->mii_bus = mdiobus_alloc(); + if (!priv->mii_bus) { + ret = -ENOMEM; + goto out_uninit_hw; + } + + bus = priv->mii_bus; + bus->name = "bcm63xx_enet MII bus"; + bus->parent = &pdev->dev; + bus->priv = priv; + bus->read = bcm_enet_mdio_read_phylib; + bus->write = bcm_enet_mdio_write_phylib; + sprintf(bus->id, "%d", priv->mac_id); + + /* only probe bus where we think the PHY is, because + * the mdio read operation return 0 instead of 0xffff + * if a slave is not present on hw */ + bus->phy_mask = ~(1 << priv->phy_id); + + bus->irq = kmalloc(sizeof(int) * PHY_MAX_ADDR, GFP_KERNEL); + if (!bus->irq) { + ret = -ENOMEM; + goto out_free_mdio; + } + + if (priv->has_phy_interrupt) + bus->irq[priv->phy_id] = priv->phy_interrupt; + else + bus->irq[priv->phy_id] = PHY_POLL; + + ret = mdiobus_register(bus); + if (ret) { + dev_err(&pdev->dev, "unable to register mdio bus\n"); + goto out_free_mdio; + } + } else { + + /* run platform code to initialize PHY device */ + if (pd->mii_config && + pd->mii_config(dev, 1, bcm_enet_mdio_read_mii, + bcm_enet_mdio_write_mii)) { + dev_err(&pdev->dev, "unable to configure mdio bus\n"); + goto out_uninit_hw; + } + } + + spin_lock_init(&priv->rx_lock); + + /* init rx timeout (used for oom) */ + init_timer(&priv->rx_timeout); + priv->rx_timeout.function = bcm_enet_refill_rx_timer; + priv->rx_timeout.data = (unsigned long)dev; + + /* init the mib update lock&work */ + mutex_init(&priv->mib_update_lock); + INIT_WORK(&priv->mib_update_task, bcm_enet_update_mib_counters_defer); + + /* zero mib counters */ + for (i = 0; i < ENET_MIB_REG_COUNT; i++) + enet_writel(priv, 0, ENET_MIB_REG(i)); + + /* register netdevice */ + dev->netdev_ops = &bcm_enet_ops; + netif_napi_add(dev, &priv->napi, bcm_enet_poll, 16); + + SET_ETHTOOL_OPS(dev, &bcm_enet_ethtool_ops); + SET_NETDEV_DEV(dev, &pdev->dev); + + ret = register_netdev(dev); + if (ret) + goto out_unregister_mdio; + + netif_carrier_off(dev); + platform_set_drvdata(pdev, dev); + priv->pdev = pdev; + priv->net_dev = dev; + + return 0; + +out_unregister_mdio: + if (priv->mii_bus) { + mdiobus_unregister(priv->mii_bus); + kfree(priv->mii_bus->irq); + } + +out_free_mdio: + if (priv->mii_bus) + mdiobus_free(priv->mii_bus); + +out_uninit_hw: + /* turn off mdc clock */ + enet_writel(priv, 0, ENET_MIISC_REG); + if (priv->phy_clk) { + clk_disable(priv->phy_clk); + clk_put(priv->phy_clk); + } + +out_put_clk_mac: + clk_disable(priv->mac_clk); + clk_put(priv->mac_clk); + +out_unmap: + iounmap(priv->base); + +out_release_mem: + release_mem_region(res_mem->start, iomem_size); +out: + free_netdev(dev); + return ret; +} + + +/* + * exit func, stops hardware and unregisters netdevice + */ +static int __devexit bcm_enet_remove(struct platform_device *pdev) +{ + struct bcm_enet_priv *priv; + struct net_device *dev; + struct resource *res; + + /* stop netdevice */ + dev = platform_get_drvdata(pdev); + priv = netdev_priv(dev); + unregister_netdev(dev); + + /* turn off mdc clock */ + enet_writel(priv, 0, ENET_MIISC_REG); + + if (priv->has_phy) { + mdiobus_unregister(priv->mii_bus); + kfree(priv->mii_bus->irq); + mdiobus_free(priv->mii_bus); + } else { + struct bcm63xx_enet_platform_data *pd; + + pd = pdev->dev.platform_data; + if (pd && pd->mii_config) + pd->mii_config(dev, 0, bcm_enet_mdio_read_mii, + bcm_enet_mdio_write_mii); + } + + /* release device resources */ + iounmap(priv->base); + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(res->start, res->end - res->start + 1); + + /* disable hw block clocks */ + if (priv->phy_clk) { + clk_disable(priv->phy_clk); + clk_put(priv->phy_clk); + } + clk_disable(priv->mac_clk); + clk_put(priv->mac_clk); + + platform_set_drvdata(pdev, NULL); + free_netdev(dev); + return 0; +} + +struct platform_driver bcm63xx_enet_driver = { + .probe = bcm_enet_probe, + .remove = __devexit_p(bcm_enet_remove), + .driver = { + .name = "bcm63xx_enet", + .owner = THIS_MODULE, + }, +}; + +/* + * reserve & remap memory space shared between all macs + */ +static int __devinit bcm_enet_shared_probe(struct platform_device *pdev) +{ + struct resource *res; + unsigned int iomem_size; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) + return -ENODEV; + + iomem_size = res->end - res->start + 1; + if (!request_mem_region(res->start, iomem_size, "bcm63xx_enet_dma")) + return -EBUSY; + + bcm_enet_shared_base = ioremap(res->start, iomem_size); + if (!bcm_enet_shared_base) { + release_mem_region(res->start, iomem_size); + return -ENOMEM; + } + return 0; +} + +static int __devexit bcm_enet_shared_remove(struct platform_device *pdev) +{ + struct resource *res; + + iounmap(bcm_enet_shared_base); + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(res->start, res->end - res->start + 1); + return 0; +} + +/* + * this "shared" driver is needed because both macs share a single + * address space + */ +struct platform_driver bcm63xx_enet_shared_driver = { + .probe = bcm_enet_shared_probe, + .remove = __devexit_p(bcm_enet_shared_remove), + .driver = { + .name = "bcm63xx_enet_shared", + .owner = THIS_MODULE, + }, +}; + +/* + * entry point + */ +static int __init bcm_enet_init(void) +{ + int ret; + + ret = platform_driver_register(&bcm63xx_enet_shared_driver); + if (ret) + return ret; + + ret = platform_driver_register(&bcm63xx_enet_driver); + if (ret) + platform_driver_unregister(&bcm63xx_enet_shared_driver); + + return ret; +} + +static void __exit bcm_enet_exit(void) +{ + platform_driver_unregister(&bcm63xx_enet_driver); + platform_driver_unregister(&bcm63xx_enet_shared_driver); +} + + +module_init(bcm_enet_init); +module_exit(bcm_enet_exit); + +MODULE_DESCRIPTION("BCM63xx internal ethernet mac driver"); +MODULE_AUTHOR("Maxime Bizon <mbizon@freebox.fr>"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/bcm63xx_enet.h b/drivers/net/bcm63xx_enet.h new file mode 100644 index 00000000000..bd3684d42d7 --- /dev/null +++ b/drivers/net/bcm63xx_enet.h @@ -0,0 +1,303 @@ +#ifndef BCM63XX_ENET_H_ +#define BCM63XX_ENET_H_ + +#include <linux/types.h> +#include <linux/mii.h> +#include <linux/mutex.h> +#include <linux/phy.h> +#include <linux/platform_device.h> + +#include <bcm63xx_regs.h> +#include <bcm63xx_irq.h> +#include <bcm63xx_io.h> + +/* default number of descriptor */ +#define BCMENET_DEF_RX_DESC 64 +#define BCMENET_DEF_TX_DESC 32 + +/* maximum burst len for dma (4 bytes unit) */ +#define BCMENET_DMA_MAXBURST 16 + +/* tx transmit threshold (4 bytes unit), fifo is 256 bytes, the value + * must be low enough so that a DMA transfer of above burst length can + * not overflow the fifo */ +#define BCMENET_TX_FIFO_TRESH 32 + +/* + * hardware maximum rx/tx packet size including FCS, max mtu is + * actually 2047, but if we set max rx size register to 2047 we won't + * get overflow information if packet size is 2048 or above + */ +#define BCMENET_MAX_MTU 2046 + +/* + * rx/tx dma descriptor + */ +struct bcm_enet_desc { + u32 len_stat; + u32 address; +}; + +#define DMADESC_LENGTH_SHIFT 16 +#define DMADESC_LENGTH_MASK (0xfff << DMADESC_LENGTH_SHIFT) +#define DMADESC_OWNER_MASK (1 << 15) +#define DMADESC_EOP_MASK (1 << 14) +#define DMADESC_SOP_MASK (1 << 13) +#define DMADESC_ESOP_MASK (DMADESC_EOP_MASK | DMADESC_SOP_MASK) +#define DMADESC_WRAP_MASK (1 << 12) + +#define DMADESC_UNDER_MASK (1 << 9) +#define DMADESC_APPEND_CRC (1 << 8) +#define DMADESC_OVSIZE_MASK (1 << 4) +#define DMADESC_RXER_MASK (1 << 2) +#define DMADESC_CRC_MASK (1 << 1) +#define DMADESC_OV_MASK (1 << 0) +#define DMADESC_ERR_MASK (DMADESC_UNDER_MASK | \ + DMADESC_OVSIZE_MASK | \ + DMADESC_RXER_MASK | \ + DMADESC_CRC_MASK | \ + DMADESC_OV_MASK) + + +/* + * MIB Counters register definitions +*/ +#define ETH_MIB_TX_GD_OCTETS 0 +#define ETH_MIB_TX_GD_PKTS 1 +#define ETH_MIB_TX_ALL_OCTETS 2 +#define ETH_MIB_TX_ALL_PKTS 3 +#define ETH_MIB_TX_BRDCAST 4 +#define ETH_MIB_TX_MULT 5 +#define ETH_MIB_TX_64 6 +#define ETH_MIB_TX_65_127 7 +#define ETH_MIB_TX_128_255 8 +#define ETH_MIB_TX_256_511 9 +#define ETH_MIB_TX_512_1023 10 +#define ETH_MIB_TX_1024_MAX 11 +#define ETH_MIB_TX_JAB 12 +#define ETH_MIB_TX_OVR 13 +#define ETH_MIB_TX_FRAG 14 +#define ETH_MIB_TX_UNDERRUN 15 +#define ETH_MIB_TX_COL 16 +#define ETH_MIB_TX_1_COL 17 +#define ETH_MIB_TX_M_COL 18 +#define ETH_MIB_TX_EX_COL 19 +#define ETH_MIB_TX_LATE 20 +#define ETH_MIB_TX_DEF 21 +#define ETH_MIB_TX_CRS 22 +#define ETH_MIB_TX_PAUSE 23 + +#define ETH_MIB_RX_GD_OCTETS 32 +#define ETH_MIB_RX_GD_PKTS 33 +#define ETH_MIB_RX_ALL_OCTETS 34 +#define ETH_MIB_RX_ALL_PKTS 35 +#define ETH_MIB_RX_BRDCAST 36 +#define ETH_MIB_RX_MULT 37 +#define ETH_MIB_RX_64 38 +#define ETH_MIB_RX_65_127 39 +#define ETH_MIB_RX_128_255 40 +#define ETH_MIB_RX_256_511 41 +#define ETH_MIB_RX_512_1023 42 +#define ETH_MIB_RX_1024_MAX 43 +#define ETH_MIB_RX_JAB 44 +#define ETH_MIB_RX_OVR 45 +#define ETH_MIB_RX_FRAG 46 +#define ETH_MIB_RX_DROP 47 +#define ETH_MIB_RX_CRC_ALIGN 48 +#define ETH_MIB_RX_UND 49 +#define ETH_MIB_RX_CRC 50 +#define ETH_MIB_RX_ALIGN 51 +#define ETH_MIB_RX_SYM 52 +#define ETH_MIB_RX_PAUSE 53 +#define ETH_MIB_RX_CNTRL 54 + + +struct bcm_enet_mib_counters { + u64 tx_gd_octets; + u32 tx_gd_pkts; + u32 tx_all_octets; + u32 tx_all_pkts; + u32 tx_brdcast; + u32 tx_mult; + u32 tx_64; + u32 tx_65_127; + u32 tx_128_255; + u32 tx_256_511; + u32 tx_512_1023; + u32 tx_1024_max; + u32 tx_jab; + u32 tx_ovr; + u32 tx_frag; + u32 tx_underrun; + u32 tx_col; + u32 tx_1_col; + u32 tx_m_col; + u32 tx_ex_col; + u32 tx_late; + u32 tx_def; + u32 tx_crs; + u32 tx_pause; + u64 rx_gd_octets; + u32 rx_gd_pkts; + u32 rx_all_octets; + u32 rx_all_pkts; + u32 rx_brdcast; + u32 rx_mult; + u32 rx_64; + u32 rx_65_127; + u32 rx_128_255; + u32 rx_256_511; + u32 rx_512_1023; + u32 rx_1024_max; + u32 rx_jab; + u32 rx_ovr; + u32 rx_frag; + u32 rx_drop; + u32 rx_crc_align; + u32 rx_und; + u32 rx_crc; + u32 rx_align; + u32 rx_sym; + u32 rx_pause; + u32 rx_cntrl; +}; + + +struct bcm_enet_priv { + + /* mac id (from platform device id) */ + int mac_id; + + /* base remapped address of device */ + void __iomem *base; + + /* mac irq, rx_dma irq, tx_dma irq */ + int irq; + int irq_rx; + int irq_tx; + + /* hw view of rx & tx dma ring */ + dma_addr_t rx_desc_dma; + dma_addr_t tx_desc_dma; + + /* allocated size (in bytes) for rx & tx dma ring */ + unsigned int rx_desc_alloc_size; + unsigned int tx_desc_alloc_size; + + + struct napi_struct napi; + + /* dma channel id for rx */ + int rx_chan; + + /* number of dma desc in rx ring */ + int rx_ring_size; + + /* cpu view of rx dma ring */ + struct bcm_enet_desc *rx_desc_cpu; + + /* current number of armed descriptor given to hardware for rx */ + int rx_desc_count; + + /* next rx descriptor to fetch from hardware */ + int rx_curr_desc; + + /* next dirty rx descriptor to refill */ + int rx_dirty_desc; + + /* size of allocated rx skbs */ + unsigned int rx_skb_size; + + /* list of skb given to hw for rx */ + struct sk_buff **rx_skb; + + /* used when rx skb allocation failed, so we defer rx queue + * refill */ + struct timer_list rx_timeout; + + /* lock rx_timeout against rx normal operation */ + spinlock_t rx_lock; + + + /* dma channel id for tx */ + int tx_chan; + + /* number of dma desc in tx ring */ + int tx_ring_size; + + /* cpu view of rx dma ring */ + struct bcm_enet_desc *tx_desc_cpu; + + /* number of available descriptor for tx */ + int tx_desc_count; + + /* next tx descriptor avaiable */ + int tx_curr_desc; + + /* next dirty tx descriptor to reclaim */ + int tx_dirty_desc; + + /* list of skb given to hw for tx */ + struct sk_buff **tx_skb; + + /* lock used by tx reclaim and xmit */ + spinlock_t tx_lock; + + + /* set if internal phy is ignored and external mii interface + * is selected */ + int use_external_mii; + + /* set if a phy is connected, phy address must be known, + * probing is not possible */ + int has_phy; + int phy_id; + + /* set if connected phy has an associated irq */ + int has_phy_interrupt; + int phy_interrupt; + + /* used when a phy is connected (phylib used) */ + struct mii_bus *mii_bus; + struct phy_device *phydev; + int old_link; + int old_duplex; + int old_pause; + + /* used when no phy is connected */ + int force_speed_100; + int force_duplex_full; + + /* pause parameters */ + int pause_auto; + int pause_rx; + int pause_tx; + + /* stats */ + struct net_device_stats stats; + struct bcm_enet_mib_counters mib; + + /* after mib interrupt, mib registers update is done in this + * work queue */ + struct work_struct mib_update_task; + + /* lock mib update between userspace request and workqueue */ + struct mutex mib_update_lock; + + /* mac clock */ + struct clk *mac_clk; + + /* phy clock if internal phy is used */ + struct clk *phy_clk; + + /* network device reference */ + struct net_device *net_dev; + + /* platform device reference */ + struct platform_device *pdev; + + /* maximum hardware transmit/receive size */ + unsigned int hw_mtu; +}; + +#endif /* ! BCM63XX_ENET_H_ */ diff --git a/drivers/net/benet/be.h b/drivers/net/benet/be.h index 13b72ce870d..684c6fe24c8 100644 --- a/drivers/net/benet/be.h +++ b/drivers/net/benet/be.h @@ -362,5 +362,6 @@ static inline u8 is_udp_pkt(struct sk_buff *skb) extern void be_cq_notify(struct be_adapter *adapter, u16 qid, bool arm, u16 num_popped); extern void be_link_status_update(struct be_adapter *adapter, bool link_up); +extern void netdev_stats_update(struct be_adapter *adapter); extern int be_load_fw(struct be_adapter *adapter, u8 *func); #endif /* BE_H */ diff --git a/drivers/net/benet/be_cmds.c b/drivers/net/benet/be_cmds.c index 1db09249830..3dd76c4170b 100644 --- a/drivers/net/benet/be_cmds.c +++ b/drivers/net/benet/be_cmds.c @@ -59,15 +59,22 @@ static int be_mcc_compl_process(struct be_adapter *adapter, compl_status = (compl->status >> CQE_STATUS_COMPL_SHIFT) & CQE_STATUS_COMPL_MASK; - if (compl_status != MCC_STATUS_SUCCESS) { + if (compl_status == MCC_STATUS_SUCCESS) { + if (compl->tag0 == OPCODE_ETH_GET_STATISTICS) { + struct be_cmd_resp_get_stats *resp = + adapter->stats.cmd.va; + be_dws_le_to_cpu(&resp->hw_stats, + sizeof(resp->hw_stats)); + netdev_stats_update(adapter); + } + } else if (compl_status != MCC_STATUS_NOT_SUPPORTED) { extd_status = (compl->status >> CQE_STATUS_EXTD_SHIFT) & CQE_STATUS_EXTD_MASK; dev_warn(&adapter->pdev->dev, "Error in cmd completion: status(compl/extd)=%d/%d\n", compl_status, extd_status); - return -1; } - return 0; + return compl_status; } /* Link state evt is a string of bytes; no need for endian swapping */ @@ -97,10 +104,10 @@ static struct be_mcc_compl *be_mcc_compl_get(struct be_adapter *adapter) return NULL; } -void be_process_mcc(struct be_adapter *adapter) +int be_process_mcc(struct be_adapter *adapter) { struct be_mcc_compl *compl; - int num = 0; + int num = 0, status = 0; spin_lock_bh(&adapter->mcc_cq_lock); while ((compl = be_mcc_compl_get(adapter))) { @@ -111,38 +118,47 @@ void be_process_mcc(struct be_adapter *adapter) /* Interpret compl as a async link evt */ be_async_link_state_process(adapter, (struct be_async_event_link_state *) compl); - } else { - be_mcc_compl_process(adapter, compl); - atomic_dec(&adapter->mcc_obj.q.used); + } else if (compl->flags & CQE_FLAGS_COMPLETED_MASK) { + status = be_mcc_compl_process(adapter, compl); + atomic_dec(&adapter->mcc_obj.q.used); } be_mcc_compl_use(compl); num++; } + if (num) be_cq_notify(adapter, adapter->mcc_obj.cq.id, true, num); + spin_unlock_bh(&adapter->mcc_cq_lock); + return status; } /* Wait till no more pending mcc requests are present */ -static void be_mcc_wait_compl(struct be_adapter *adapter) +static int be_mcc_wait_compl(struct be_adapter *adapter) { -#define mcc_timeout 50000 /* 5s timeout */ - int i; +#define mcc_timeout 120000 /* 12s timeout */ + int i, status; for (i = 0; i < mcc_timeout; i++) { - be_process_mcc(adapter); + status = be_process_mcc(adapter); + if (status) + return status; + if (atomic_read(&adapter->mcc_obj.q.used) == 0) break; udelay(100); } - if (i == mcc_timeout) + if (i == mcc_timeout) { dev_err(&adapter->pdev->dev, "mccq poll timed out\n"); + return -1; + } + return 0; } /* Notify MCC requests and wait for completion */ -static void be_mcc_notify_wait(struct be_adapter *adapter) +static int be_mcc_notify_wait(struct be_adapter *adapter) { be_mcc_notify(adapter); - be_mcc_wait_compl(adapter); + return be_mcc_wait_compl(adapter); } static int be_mbox_db_ready_wait(struct be_adapter *adapter, void __iomem *db) @@ -173,7 +189,7 @@ static int be_mbox_db_ready_wait(struct be_adapter *adapter, void __iomem *db) * Insert the mailbox address into the doorbell in two steps * Polls on the mbox doorbell till a command completion (or a timeout) occurs */ -static int be_mbox_notify(struct be_adapter *adapter) +static int be_mbox_notify_wait(struct be_adapter *adapter) { int status; u32 val = 0; @@ -182,8 +198,6 @@ static int be_mbox_notify(struct be_adapter *adapter) struct be_mcc_mailbox *mbox = mbox_mem->va; struct be_mcc_compl *compl = &mbox->compl; - memset(compl, 0, sizeof(*compl)); - val |= MPU_MAILBOX_DB_HI_MASK; /* at bits 2 - 31 place mbox dma addr msb bits 34 - 63 */ val |= (upper_32_bits(mbox_mem->dma) >> 2) << 2; @@ -310,34 +324,40 @@ static u32 eq_delay_to_mult(u32 usec_delay) return multiplier; } -static inline struct be_mcc_wrb *wrb_from_mbox(struct be_dma_mem *mbox_mem) +static inline struct be_mcc_wrb *wrb_from_mbox(struct be_adapter *adapter) { - return &((struct be_mcc_mailbox *)(mbox_mem->va))->wrb; + struct be_dma_mem *mbox_mem = &adapter->mbox_mem; + struct be_mcc_wrb *wrb + = &((struct be_mcc_mailbox *)(mbox_mem->va))->wrb; + memset(wrb, 0, sizeof(*wrb)); + return wrb; } -static inline struct be_mcc_wrb *wrb_from_mcc(struct be_queue_info *mccq) +static struct be_mcc_wrb *wrb_from_mccq(struct be_adapter *adapter) { - struct be_mcc_wrb *wrb = NULL; - if (atomic_read(&mccq->used) < mccq->len) { - wrb = queue_head_node(mccq); - queue_head_inc(mccq); - atomic_inc(&mccq->used); - memset(wrb, 0, sizeof(*wrb)); - } + struct be_queue_info *mccq = &adapter->mcc_obj.q; + struct be_mcc_wrb *wrb; + + BUG_ON(atomic_read(&mccq->used) >= mccq->len); + wrb = queue_head_node(mccq); + queue_head_inc(mccq); + atomic_inc(&mccq->used); + memset(wrb, 0, sizeof(*wrb)); return wrb; } int be_cmd_eq_create(struct be_adapter *adapter, struct be_queue_info *eq, int eq_delay) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_eq_create *req = embedded_payload(wrb); - struct be_cmd_resp_eq_create *resp = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_eq_create *req; struct be_dma_mem *q_mem = &eq->dma_mem; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -359,25 +379,29 @@ int be_cmd_eq_create(struct be_adapter *adapter, be_cmd_page_addrs_prepare(req->pages, ARRAY_SIZE(req->pages), q_mem); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { + struct be_cmd_resp_eq_create *resp = embedded_payload(wrb); eq->id = le16_to_cpu(resp->eq_id); eq->created = true; } + spin_unlock(&adapter->mbox_lock); return status; } +/* Uses mbox */ int be_cmd_mac_addr_query(struct be_adapter *adapter, u8 *mac_addr, u8 type, bool permanent, u32 if_handle) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_mac_query *req = embedded_payload(wrb); - struct be_cmd_resp_mac_query *resp = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_mac_query *req; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -388,27 +412,32 @@ int be_cmd_mac_addr_query(struct be_adapter *adapter, u8 *mac_addr, if (permanent) { req->permanent = 1; } else { - req->if_id = cpu_to_le16((u16)if_handle); + req->if_id = cpu_to_le16((u16) if_handle); req->permanent = 0; } - status = be_mbox_notify(adapter); - if (!status) + status = be_mbox_notify_wait(adapter); + if (!status) { + struct be_cmd_resp_mac_query *resp = embedded_payload(wrb); memcpy(mac_addr, resp->mac.addr, ETH_ALEN); + } spin_unlock(&adapter->mbox_lock); return status; } +/* Uses synchronous MCCQ */ int be_cmd_pmac_add(struct be_adapter *adapter, u8 *mac_addr, u32 if_id, u32 *pmac_id) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_pmac_add *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_pmac_add *req; int status; - spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + spin_lock_bh(&adapter->mcc_lock); + + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -418,24 +447,27 @@ int be_cmd_pmac_add(struct be_adapter *adapter, u8 *mac_addr, req->if_id = cpu_to_le32(if_id); memcpy(req->mac_address, mac_addr, ETH_ALEN); - status = be_mbox_notify(adapter); + status = be_mcc_notify_wait(adapter); if (!status) { struct be_cmd_resp_pmac_add *resp = embedded_payload(wrb); *pmac_id = le32_to_cpu(resp->pmac_id); } - spin_unlock(&adapter->mbox_lock); + spin_unlock_bh(&adapter->mcc_lock); return status; } +/* Uses synchronous MCCQ */ int be_cmd_pmac_del(struct be_adapter *adapter, u32 if_id, u32 pmac_id) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_pmac_del *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_pmac_del *req; int status; - spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + spin_lock_bh(&adapter->mcc_lock); + + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -445,25 +477,29 @@ int be_cmd_pmac_del(struct be_adapter *adapter, u32 if_id, u32 pmac_id) req->if_id = cpu_to_le32(if_id); req->pmac_id = cpu_to_le32(pmac_id); - status = be_mbox_notify(adapter); - spin_unlock(&adapter->mbox_lock); + status = be_mcc_notify_wait(adapter); + + spin_unlock_bh(&adapter->mcc_lock); return status; } +/* Uses Mbox */ int be_cmd_cq_create(struct be_adapter *adapter, struct be_queue_info *cq, struct be_queue_info *eq, bool sol_evts, bool no_delay, int coalesce_wm) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_cq_create *req = embedded_payload(wrb); - struct be_cmd_resp_cq_create *resp = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_cq_create *req; struct be_dma_mem *q_mem = &cq->dma_mem; - void *ctxt = &req->context; + void *ctxt; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); + ctxt = &req->context; be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -486,11 +522,13 @@ int be_cmd_cq_create(struct be_adapter *adapter, be_cmd_page_addrs_prepare(req->pages, ARRAY_SIZE(req->pages), q_mem); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { + struct be_cmd_resp_cq_create *resp = embedded_payload(wrb); cq->id = le16_to_cpu(resp->cq_id); cq->created = true; } + spin_unlock(&adapter->mbox_lock); return status; @@ -508,14 +546,17 @@ int be_cmd_mccq_create(struct be_adapter *adapter, struct be_queue_info *mccq, struct be_queue_info *cq) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_mcc_create *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_mcc_create *req; struct be_dma_mem *q_mem = &mccq->dma_mem; - void *ctxt = &req->context; + void *ctxt; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); + ctxt = &req->context; be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -534,7 +575,7 @@ int be_cmd_mccq_create(struct be_adapter *adapter, be_cmd_page_addrs_prepare(req->pages, ARRAY_SIZE(req->pages), q_mem); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { struct be_cmd_resp_mcc_create *resp = embedded_payload(wrb); mccq->id = le16_to_cpu(resp->id); @@ -549,15 +590,17 @@ int be_cmd_txq_create(struct be_adapter *adapter, struct be_queue_info *txq, struct be_queue_info *cq) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_eth_tx_create *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_eth_tx_create *req; struct be_dma_mem *q_mem = &txq->dma_mem; - void *ctxt = &req->context; + void *ctxt; int status; - u32 len_encoded; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); + ctxt = &req->context; be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -568,10 +611,8 @@ int be_cmd_txq_create(struct be_adapter *adapter, req->ulp_num = BE_ULP1_NUM; req->type = BE_ETH_TX_RING_TYPE_STANDARD; - len_encoded = fls(txq->len); /* log2(len) + 1 */ - if (len_encoded == 16) - len_encoded = 0; - AMAP_SET_BITS(struct amap_tx_context, tx_ring_size, ctxt, len_encoded); + AMAP_SET_BITS(struct amap_tx_context, tx_ring_size, ctxt, + be_encoded_q_len(txq->len)); AMAP_SET_BITS(struct amap_tx_context, pci_func_id, ctxt, be_pci_func(adapter)); AMAP_SET_BITS(struct amap_tx_context, ctx_valid, ctxt, 1); @@ -581,28 +622,32 @@ int be_cmd_txq_create(struct be_adapter *adapter, be_cmd_page_addrs_prepare(req->pages, ARRAY_SIZE(req->pages), q_mem); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { struct be_cmd_resp_eth_tx_create *resp = embedded_payload(wrb); txq->id = le16_to_cpu(resp->cid); txq->created = true; } + spin_unlock(&adapter->mbox_lock); return status; } +/* Uses mbox */ int be_cmd_rxq_create(struct be_adapter *adapter, struct be_queue_info *rxq, u16 cq_id, u16 frag_size, u16 max_frame_size, u32 if_id, u32 rss) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_eth_rx_create *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_eth_rx_create *req; struct be_dma_mem *q_mem = &rxq->dma_mem; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -617,29 +662,34 @@ int be_cmd_rxq_create(struct be_adapter *adapter, req->max_frame_size = cpu_to_le16(max_frame_size); req->rss_queue = cpu_to_le32(rss); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { struct be_cmd_resp_eth_rx_create *resp = embedded_payload(wrb); rxq->id = le16_to_cpu(resp->id); rxq->created = true; } + spin_unlock(&adapter->mbox_lock); return status; } -/* Generic destroyer function for all types of queues */ +/* Generic destroyer function for all types of queues + * Uses Mbox + */ int be_cmd_q_destroy(struct be_adapter *adapter, struct be_queue_info *q, int queue_type) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_q_destroy *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_q_destroy *req; u8 subsys = 0, opcode = 0; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); + be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); switch (queue_type) { @@ -669,23 +719,27 @@ int be_cmd_q_destroy(struct be_adapter *adapter, struct be_queue_info *q, be_cmd_hdr_prepare(&req->hdr, subsys, opcode, sizeof(*req)); req->id = cpu_to_le16(q->id); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); spin_unlock(&adapter->mbox_lock); return status; } -/* Create an rx filtering policy configuration on an i/f */ +/* Create an rx filtering policy configuration on an i/f + * Uses mbox + */ int be_cmd_if_create(struct be_adapter *adapter, u32 flags, u8 *mac, bool pmac_invalid, u32 *if_handle, u32 *pmac_id) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_if_create *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_if_create *req; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -694,10 +748,11 @@ int be_cmd_if_create(struct be_adapter *adapter, u32 flags, u8 *mac, req->capability_flags = cpu_to_le32(flags); req->enable_flags = cpu_to_le32(flags); + req->pmac_invalid = pmac_invalid; if (!pmac_invalid) memcpy(req->mac_addr, mac, ETH_ALEN); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { struct be_cmd_resp_if_create *resp = embedded_payload(wrb); *if_handle = le32_to_cpu(resp->interface_id); @@ -709,14 +764,17 @@ int be_cmd_if_create(struct be_adapter *adapter, u32 flags, u8 *mac, return status; } +/* Uses mbox */ int be_cmd_if_destroy(struct be_adapter *adapter, u32 interface_id) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_if_destroy *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_if_destroy *req; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -724,7 +782,8 @@ int be_cmd_if_destroy(struct be_adapter *adapter, u32 interface_id) OPCODE_COMMON_NTWK_INTERFACE_DESTROY, sizeof(*req)); req->interface_id = cpu_to_le32(interface_id); - status = be_mbox_notify(adapter); + + status = be_mbox_notify_wait(adapter); spin_unlock(&adapter->mbox_lock); @@ -733,20 +792,22 @@ int be_cmd_if_destroy(struct be_adapter *adapter, u32 interface_id) /* Get stats is a non embedded command: the request is not embedded inside * WRB but is a separate dma memory block + * Uses asynchronous MCC */ int be_cmd_get_stats(struct be_adapter *adapter, struct be_dma_mem *nonemb_cmd) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_get_stats *req = nonemb_cmd->va; - struct be_sge *sge = nonembedded_sgl(wrb); - int status; + struct be_mcc_wrb *wrb; + struct be_cmd_req_get_stats *req; + struct be_sge *sge; - spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + spin_lock_bh(&adapter->mcc_lock); - memset(req, 0, sizeof(*req)); + wrb = wrb_from_mccq(adapter); + req = nonemb_cmd->va; + sge = nonembedded_sgl(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), false, 1); + wrb->tag0 = OPCODE_ETH_GET_STATISTICS; be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_ETH, OPCODE_ETH_GET_STATISTICS, sizeof(*req)); @@ -754,59 +815,61 @@ int be_cmd_get_stats(struct be_adapter *adapter, struct be_dma_mem *nonemb_cmd) sge->pa_lo = cpu_to_le32(nonemb_cmd->dma & 0xFFFFFFFF); sge->len = cpu_to_le32(nonemb_cmd->size); - status = be_mbox_notify(adapter); - if (!status) { - struct be_cmd_resp_get_stats *resp = nonemb_cmd->va; - be_dws_le_to_cpu(&resp->hw_stats, sizeof(resp->hw_stats)); - } + be_mcc_notify(adapter); - spin_unlock(&adapter->mbox_lock); - return status; + spin_unlock_bh(&adapter->mcc_lock); + return 0; } +/* Uses synchronous mcc */ int be_cmd_link_status_query(struct be_adapter *adapter, bool *link_up) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_link_status *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_link_status *req; int status; - spin_lock(&adapter->mbox_lock); + spin_lock_bh(&adapter->mcc_lock); + + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); *link_up = false; - memset(wrb, 0, sizeof(*wrb)); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_COMMON, OPCODE_COMMON_NTWK_LINK_STATUS_QUERY, sizeof(*req)); - status = be_mbox_notify(adapter); + status = be_mcc_notify_wait(adapter); if (!status) { struct be_cmd_resp_link_status *resp = embedded_payload(wrb); if (resp->mac_speed != PHY_LINK_SPEED_ZERO) *link_up = true; } - spin_unlock(&adapter->mbox_lock); + spin_unlock_bh(&adapter->mcc_lock); return status; } +/* Uses Mbox */ int be_cmd_get_fw_ver(struct be_adapter *adapter, char *fw_ver) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_get_fw_version *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_get_fw_version *req; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_COMMON, OPCODE_COMMON_GET_FW_VERSION, sizeof(*req)); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { struct be_cmd_resp_get_fw_version *resp = embedded_payload(wrb); strncpy(fw_ver, resp->firmware_version_string, FW_VER_LEN); @@ -816,15 +879,18 @@ int be_cmd_get_fw_ver(struct be_adapter *adapter, char *fw_ver) return status; } -/* set the EQ delay interval of an EQ to specified value */ +/* set the EQ delay interval of an EQ to specified value + * Uses async mcc + */ int be_cmd_modify_eqd(struct be_adapter *adapter, u32 eq_id, u32 eqd) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_modify_eq_delay *req = embedded_payload(wrb); - int status; + struct be_mcc_wrb *wrb; + struct be_cmd_req_modify_eq_delay *req; - spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + spin_lock_bh(&adapter->mcc_lock); + + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -836,21 +902,24 @@ int be_cmd_modify_eqd(struct be_adapter *adapter, u32 eq_id, u32 eqd) req->delay[0].phase = 0; req->delay[0].delay_multiplier = cpu_to_le32(eqd); - status = be_mbox_notify(adapter); + be_mcc_notify(adapter); - spin_unlock(&adapter->mbox_lock); - return status; + spin_unlock_bh(&adapter->mcc_lock); + return 0; } +/* Uses sycnhronous mcc */ int be_cmd_vlan_config(struct be_adapter *adapter, u32 if_id, u16 *vtag_array, u32 num, bool untagged, bool promiscuous) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_vlan_config *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_vlan_config *req; int status; - spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + spin_lock_bh(&adapter->mcc_lock); + + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -866,23 +935,24 @@ int be_cmd_vlan_config(struct be_adapter *adapter, u32 if_id, u16 *vtag_array, req->num_vlan * sizeof(vtag_array[0])); } - status = be_mbox_notify(adapter); + status = be_mcc_notify_wait(adapter); - spin_unlock(&adapter->mbox_lock); + spin_unlock_bh(&adapter->mcc_lock); return status; } -/* Use MCC for this command as it may be called in BH context */ +/* Uses MCC for this command as it may be called in BH context + * Uses synchronous mcc + */ int be_cmd_promiscuous_config(struct be_adapter *adapter, u8 port_num, bool en) { struct be_mcc_wrb *wrb; struct be_cmd_req_promiscuous_config *req; + int status; spin_lock_bh(&adapter->mcc_lock); - wrb = wrb_from_mcc(&adapter->mcc_obj.q); - BUG_ON(!wrb); - + wrb = wrb_from_mccq(adapter); req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -895,14 +965,14 @@ int be_cmd_promiscuous_config(struct be_adapter *adapter, u8 port_num, bool en) else req->port0_promiscuous = en; - be_mcc_notify_wait(adapter); + status = be_mcc_notify_wait(adapter); spin_unlock_bh(&adapter->mcc_lock); - return 0; + return status; } /* - * Use MCC for this command as it may be called in BH context + * Uses MCC for this command as it may be called in BH context * (mc == NULL) => multicast promiscous */ int be_cmd_multicast_set(struct be_adapter *adapter, u32 if_id, @@ -914,9 +984,7 @@ int be_cmd_multicast_set(struct be_adapter *adapter, u32 if_id, spin_lock_bh(&adapter->mcc_lock); - wrb = wrb_from_mcc(&adapter->mcc_obj.q); - BUG_ON(!wrb); - + wrb = wrb_from_mccq(adapter); req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -944,15 +1012,17 @@ int be_cmd_multicast_set(struct be_adapter *adapter, u32 if_id, return 0; } +/* Uses synchrounous mcc */ int be_cmd_set_flow_control(struct be_adapter *adapter, u32 tx_fc, u32 rx_fc) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_set_flow_control *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_set_flow_control *req; int status; - spin_lock(&adapter->mbox_lock); + spin_lock_bh(&adapter->mcc_lock); - memset(wrb, 0, sizeof(*wrb)); + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); @@ -962,28 +1032,30 @@ int be_cmd_set_flow_control(struct be_adapter *adapter, u32 tx_fc, u32 rx_fc) req->tx_flow_control = cpu_to_le16((u16)tx_fc); req->rx_flow_control = cpu_to_le16((u16)rx_fc); - status = be_mbox_notify(adapter); + status = be_mcc_notify_wait(adapter); - spin_unlock(&adapter->mbox_lock); + spin_unlock_bh(&adapter->mcc_lock); return status; } +/* Uses sycn mcc */ int be_cmd_get_flow_control(struct be_adapter *adapter, u32 *tx_fc, u32 *rx_fc) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_get_flow_control *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_get_flow_control *req; int status; - spin_lock(&adapter->mbox_lock); + spin_lock_bh(&adapter->mcc_lock); - memset(wrb, 0, sizeof(*wrb)); + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_COMMON, OPCODE_COMMON_GET_FLOW_CONTROL, sizeof(*req)); - status = be_mbox_notify(adapter); + status = be_mcc_notify_wait(adapter); if (!status) { struct be_cmd_resp_get_flow_control *resp = embedded_payload(wrb); @@ -991,26 +1063,28 @@ int be_cmd_get_flow_control(struct be_adapter *adapter, u32 *tx_fc, u32 *rx_fc) *rx_fc = le16_to_cpu(resp->rx_flow_control); } - spin_unlock(&adapter->mbox_lock); + spin_unlock_bh(&adapter->mcc_lock); return status; } +/* Uses mbox */ int be_cmd_query_fw_cfg(struct be_adapter *adapter, u32 *port_num) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_query_fw_cfg *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_query_fw_cfg *req; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_COMMON, OPCODE_COMMON_QUERY_FIRMWARE_CONFIG, sizeof(*req)); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); if (!status) { struct be_cmd_resp_query_fw_cfg *resp = embedded_payload(wrb); *port_num = le32_to_cpu(resp->phys_port); @@ -1020,22 +1094,24 @@ int be_cmd_query_fw_cfg(struct be_adapter *adapter, u32 *port_num) return status; } +/* Uses mbox */ int be_cmd_reset_function(struct be_adapter *adapter) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); - struct be_cmd_req_hdr *req = embedded_payload(wrb); + struct be_mcc_wrb *wrb; + struct be_cmd_req_hdr *req; int status; spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + wrb = wrb_from_mbox(adapter); + req = embedded_payload(wrb); be_wrb_hdr_prepare(wrb, sizeof(*req), true, 0); be_cmd_hdr_prepare(req, CMD_SUBSYSTEM_COMMON, OPCODE_COMMON_FUNCTION_RESET, sizeof(*req)); - status = be_mbox_notify(adapter); + status = be_mbox_notify_wait(adapter); spin_unlock(&adapter->mbox_lock); return status; @@ -1044,13 +1120,17 @@ int be_cmd_reset_function(struct be_adapter *adapter) int be_cmd_write_flashrom(struct be_adapter *adapter, struct be_dma_mem *cmd, u32 flash_type, u32 flash_opcode, u32 buf_size) { - struct be_mcc_wrb *wrb = wrb_from_mbox(&adapter->mbox_mem); + struct be_mcc_wrb *wrb; struct be_cmd_write_flashrom *req = cmd->va; - struct be_sge *sge = nonembedded_sgl(wrb); + struct be_sge *sge; int status; - spin_lock(&adapter->mbox_lock); - memset(wrb, 0, sizeof(*wrb)); + spin_lock_bh(&adapter->mcc_lock); + + wrb = wrb_from_mccq(adapter); + req = embedded_payload(wrb); + sge = nonembedded_sgl(wrb); + be_wrb_hdr_prepare(wrb, cmd->size, false, 1); be_cmd_hdr_prepare(&req->hdr, CMD_SUBSYSTEM_COMMON, @@ -1063,8 +1143,8 @@ int be_cmd_write_flashrom(struct be_adapter *adapter, struct be_dma_mem *cmd, req->params.op_code = cpu_to_le32(flash_opcode); req->params.data_buf_size = cpu_to_le32(buf_size); - status = be_mbox_notify(adapter); + status = be_mcc_notify_wait(adapter); - spin_unlock(&adapter->mbox_lock); + spin_unlock_bh(&adapter->mcc_lock); return status; } diff --git a/drivers/net/benet/be_cmds.h b/drivers/net/benet/be_cmds.h index fd7028e5b78..93e432f3d92 100644 --- a/drivers/net/benet/be_cmds.h +++ b/drivers/net/benet/be_cmds.h @@ -61,7 +61,8 @@ enum { /* The command is completing because the queue was getting flushed */ MCC_STATUS_QUEUE_FLUSHING = 0x4, /* The command is completing with a DMA error */ - MCC_STATUS_DMA_FAILED = 0x5 + MCC_STATUS_DMA_FAILED = 0x5, + MCC_STATUS_NOT_SUPPORTED = 0x66 }; #define CQE_STATUS_COMPL_MASK 0xFFFF @@ -761,7 +762,7 @@ extern int be_cmd_get_flow_control(struct be_adapter *adapter, u32 *tx_fc, u32 *rx_fc); extern int be_cmd_query_fw_cfg(struct be_adapter *adapter, u32 *port_num); extern int be_cmd_reset_function(struct be_adapter *adapter); -extern void be_process_mcc(struct be_adapter *adapter); +extern int be_process_mcc(struct be_adapter *adapter); extern int be_cmd_write_flashrom(struct be_adapter *adapter, struct be_dma_mem *cmd, u32 flash_oper, u32 flash_opcode, u32 buf_size); diff --git a/drivers/net/benet/be_main.c b/drivers/net/benet/be_main.c index ce11bba2cb6..409cf059590 100644 --- a/drivers/net/benet/be_main.c +++ b/drivers/net/benet/be_main.c @@ -135,7 +135,7 @@ static int be_mac_addr_set(struct net_device *netdev, void *p) return status; } -static void netdev_stats_update(struct be_adapter *adapter) +void netdev_stats_update(struct be_adapter *adapter) { struct be_hw_stats *hw_stats = hw_stats_from_cmd(adapter->stats.cmd.va); struct be_rxf_stats *rxf_stats = &hw_stats->rxf; @@ -431,8 +431,7 @@ static int make_tx_wrbs(struct be_adapter *adapter, } static netdev_tx_t be_xmit(struct sk_buff *skb, - struct net_device *netdev) - + struct net_device *netdev) { struct be_adapter *adapter = netdev_priv(netdev); struct be_tx_obj *tx_obj = &adapter->tx_obj; @@ -490,11 +489,11 @@ static int be_change_mtu(struct net_device *netdev, int new_mtu) * program them in BE. If more than BE_NUM_VLANS_SUPPORTED are configured, * set the BE in promiscuous VLAN mode. */ -static void be_vid_config(struct net_device *netdev) +static int be_vid_config(struct be_adapter *adapter) { - struct be_adapter *adapter = netdev_priv(netdev); u16 vtag[BE_NUM_VLANS_SUPPORTED]; u16 ntags = 0, i; + int status; if (adapter->num_vlans <= BE_NUM_VLANS_SUPPORTED) { /* Construct VLAN Table to give to HW */ @@ -504,12 +503,13 @@ static void be_vid_config(struct net_device *netdev) ntags++; } } - be_cmd_vlan_config(adapter, adapter->if_handle, - vtag, ntags, 1, 0); + status = be_cmd_vlan_config(adapter, adapter->if_handle, + vtag, ntags, 1, 0); } else { - be_cmd_vlan_config(adapter, adapter->if_handle, - NULL, 0, 1, 1); + status = be_cmd_vlan_config(adapter, adapter->if_handle, + NULL, 0, 1, 1); } + return status; } static void be_vlan_register(struct net_device *netdev, struct vlan_group *grp) @@ -532,7 +532,7 @@ static void be_vlan_add_vid(struct net_device *netdev, u16 vid) adapter->num_vlans++; adapter->vlan_tag[vid] = 1; - be_vid_config(netdev); + be_vid_config(adapter); } static void be_vlan_rem_vid(struct net_device *netdev, u16 vid) @@ -543,7 +543,7 @@ static void be_vlan_rem_vid(struct net_device *netdev, u16 vid) adapter->vlan_tag[vid] = 0; vlan_group_set_device(adapter->vlan_grp, vid, NULL); - be_vid_config(netdev); + be_vid_config(adapter); } static void be_set_multicast_list(struct net_device *netdev) @@ -1444,12 +1444,8 @@ static void be_worker(struct work_struct *work) { struct be_adapter *adapter = container_of(work, struct be_adapter, work.work); - int status; - /* Get Stats */ - status = be_cmd_get_stats(adapter, &adapter->stats.cmd); - if (!status) - netdev_stats_update(adapter); + be_cmd_get_stats(adapter, &adapter->stats.cmd); /* Set EQ delay */ be_rx_eqd_update(adapter); @@ -1622,11 +1618,6 @@ static int be_setup(struct be_adapter *adapter) if (status != 0) goto do_none; - be_vid_config(netdev); - - status = be_cmd_set_flow_control(adapter, true, true); - if (status != 0) - goto if_destroy; status = be_tx_queues_create(adapter); if (status != 0) @@ -1640,8 +1631,17 @@ static int be_setup(struct be_adapter *adapter) if (status != 0) goto rx_qs_destroy; + status = be_vid_config(adapter); + if (status != 0) + goto mccqs_destroy; + + status = be_cmd_set_flow_control(adapter, true, true); + if (status != 0) + goto mccqs_destroy; return 0; +mccqs_destroy: + be_mcc_queues_destroy(adapter); rx_qs_destroy: be_rx_queues_destroy(adapter); tx_qs_destroy: diff --git a/drivers/net/bnx2x_reg.h b/drivers/net/bnx2x_reg.h index 0695be14cf9..aa76cbada5e 100644 --- a/drivers/net/bnx2x_reg.h +++ b/drivers/net/bnx2x_reg.h @@ -3122,7 +3122,7 @@ The fields are:[4:0] - tail pointer; [10:5] - Link List size; 15:11] - header pointer. */ #define TCM_REG_XX_TABLE 0x50240 -/* [RW 4] Load value for for cfc ac credit cnt. */ +/* [RW 4] Load value for cfc ac credit cnt. */ #define TM_REG_CFC_AC_CRDCNT_VAL 0x164208 /* [RW 4] Load value for cfc cld credit cnt. */ #define TM_REG_CFC_CLD_CRDCNT_VAL 0x164210 diff --git a/drivers/net/bonding/bond_3ad.c b/drivers/net/bonding/bond_3ad.c index cea5cfe23b7..c3fa31c9f2a 100644 --- a/drivers/net/bonding/bond_3ad.c +++ b/drivers/net/bonding/bond_3ad.c @@ -1987,7 +1987,7 @@ void bond_3ad_unbind_slave(struct slave *slave) // find new aggregator for the related port(s) new_aggregator = __get_first_agg(port); for (; new_aggregator; new_aggregator = __get_next_agg(new_aggregator)) { - // if the new aggregator is empty, or it connected to to our port only + // if the new aggregator is empty, or it is connected to our port only if (!new_aggregator->lag_ports || ((new_aggregator->lag_ports == port) && !new_aggregator->lag_ports->next_port_in_aggregator)) { break; } diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index a7e731f8a0d..69c5b15e22d 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1093,15 +1093,8 @@ static struct slave *bond_find_best_slave(struct bonding *bond) return NULL; /* still no slave, return NULL */ } - /* - * first try the primary link; if arping, a link must tx/rx - * traffic before it can be considered the curr_active_slave. - * also, we would skip slaves between the curr_active_slave - * and primary_slave that may be up and able to arp - */ if ((bond->primary_slave) && - (!bond->params.arp_interval) && - (IS_UP(bond->primary_slave->dev))) { + bond->primary_slave->link == BOND_LINK_UP) { new_active = bond->primary_slave; } @@ -1109,15 +1102,14 @@ static struct slave *bond_find_best_slave(struct bonding *bond) old_active = new_active; bond_for_each_slave_from(bond, new_active, i, old_active) { - if (IS_UP(new_active->dev)) { - if (new_active->link == BOND_LINK_UP) { - return new_active; - } else if (new_active->link == BOND_LINK_BACK) { - /* link up, but waiting for stabilization */ - if (new_active->delay < mintime) { - mintime = new_active->delay; - bestslave = new_active; - } + if (new_active->link == BOND_LINK_UP) { + return new_active; + } else if (new_active->link == BOND_LINK_BACK && + IS_UP(new_active->dev)) { + /* link up, but waiting for stabilization */ + if (new_active->delay < mintime) { + mintime = new_active->delay; + bestslave = new_active; } } } @@ -1211,7 +1203,7 @@ void bond_change_active_slave(struct bonding *bond, struct slave *new_active) write_unlock_bh(&bond->curr_slave_lock); read_unlock(&bond->lock); - netdev_bonding_change(bond->dev); + netdev_bonding_change(bond->dev, NETDEV_BONDING_FAILOVER); read_lock(&bond->lock); write_lock_bh(&bond->curr_slave_lock); @@ -1469,14 +1461,17 @@ int bond_enslave(struct net_device *bond_dev, struct net_device *slave_dev) */ if (bond->slave_cnt == 0) { if (bond_dev->type != slave_dev->type) { - dev_close(bond_dev); pr_debug("%s: change device type from %d to %d\n", bond_dev->name, bond_dev->type, slave_dev->type); + + netdev_bonding_change(bond_dev, NETDEV_BONDING_OLDTYPE); + if (slave_dev->type != ARPHRD_ETHER) bond_setup_by_slave(bond_dev, slave_dev); else ether_setup(bond_dev); - dev_open(bond_dev); + + netdev_bonding_change(bond_dev, NETDEV_BONDING_NEWTYPE); } } else if (bond_dev->type != slave_dev->type) { pr_err(DRV_NAME ": %s ether type (%d) is different " @@ -2929,18 +2924,6 @@ static int bond_ab_arp_inspect(struct bonding *bond, int delta_in_ticks) } } - read_lock(&bond->curr_slave_lock); - - /* - * Trigger a commit if the primary option setting has changed. - */ - if (bond->primary_slave && - (bond->primary_slave != bond->curr_active_slave) && - (bond->primary_slave->link == BOND_LINK_UP)) - commit++; - - read_unlock(&bond->curr_slave_lock); - return commit; } @@ -2961,90 +2944,58 @@ static void bond_ab_arp_commit(struct bonding *bond, int delta_in_ticks) continue; case BOND_LINK_UP: - write_lock_bh(&bond->curr_slave_lock); - - if (!bond->curr_active_slave && - time_before_eq(jiffies, dev_trans_start(slave->dev) + - delta_in_ticks)) { + if ((!bond->curr_active_slave && + time_before_eq(jiffies, + dev_trans_start(slave->dev) + + delta_in_ticks)) || + bond->curr_active_slave != slave) { slave->link = BOND_LINK_UP; - bond_change_active_slave(bond, slave); bond->current_arp_slave = NULL; pr_info(DRV_NAME - ": %s: %s is up and now the " - "active interface\n", - bond->dev->name, slave->dev->name); - - } else if (bond->curr_active_slave != slave) { - /* this slave has just come up but we - * already have a current slave; this can - * also happen if bond_enslave adds a new - * slave that is up while we are searching - * for a new slave - */ - slave->link = BOND_LINK_UP; - bond_set_slave_inactive_flags(slave); - bond->current_arp_slave = NULL; + ": %s: link status definitely " + "up for interface %s.\n", + bond->dev->name, slave->dev->name); - pr_info(DRV_NAME - ": %s: backup interface %s is now up\n", - bond->dev->name, slave->dev->name); - } + if (!bond->curr_active_slave || + (slave == bond->primary_slave)) + goto do_failover; - write_unlock_bh(&bond->curr_slave_lock); + } - break; + continue; case BOND_LINK_DOWN: if (slave->link_failure_count < UINT_MAX) slave->link_failure_count++; slave->link = BOND_LINK_DOWN; + bond_set_slave_inactive_flags(slave); - if (slave == bond->curr_active_slave) { - pr_info(DRV_NAME - ": %s: link status down for active " - "interface %s, disabling it\n", - bond->dev->name, slave->dev->name); - - bond_set_slave_inactive_flags(slave); - - write_lock_bh(&bond->curr_slave_lock); - - bond_select_active_slave(bond); - if (bond->curr_active_slave) - bond->curr_active_slave->jiffies = - jiffies; - - write_unlock_bh(&bond->curr_slave_lock); + pr_info(DRV_NAME + ": %s: link status definitely down for " + "interface %s, disabling it\n", + bond->dev->name, slave->dev->name); + if (slave == bond->curr_active_slave) { bond->current_arp_slave = NULL; - - } else if (slave->state == BOND_STATE_BACKUP) { - pr_info(DRV_NAME - ": %s: backup interface %s is now down\n", - bond->dev->name, slave->dev->name); - - bond_set_slave_inactive_flags(slave); + goto do_failover; } - break; + + continue; default: pr_err(DRV_NAME ": %s: impossible: new_link %d on slave %s\n", bond->dev->name, slave->new_link, slave->dev->name); + continue; } - } - /* - * No race with changes to primary via sysfs, as we hold rtnl. - */ - if (bond->primary_slave && - (bond->primary_slave != bond->curr_active_slave) && - (bond->primary_slave->link == BOND_LINK_UP)) { +do_failover: + ASSERT_RTNL(); write_lock_bh(&bond->curr_slave_lock); - bond_change_active_slave(bond, bond->primary_slave); + bond_select_active_slave(bond); write_unlock_bh(&bond->curr_slave_lock); } diff --git a/drivers/net/can/Kconfig b/drivers/net/can/Kconfig index 09007437246..df32c109b7a 100644 --- a/drivers/net/can/Kconfig +++ b/drivers/net/can/Kconfig @@ -75,6 +75,13 @@ config CAN_EMS_PCI CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de). +config CAN_EMS_USB + tristate "EMS CPC-USB/ARM7 CAN/USB interface" + depends on USB && CAN_DEV + ---help--- + This driver is for the one channel CPC-USB/ARM7 CAN/USB interface + from from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de). + config CAN_KVASER_PCI tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards" depends on PCI && CAN_SJA1000 @@ -82,6 +89,12 @@ config CAN_KVASER_PCI This driver is for the the PCIcanx and PCIcan cards (1, 2 or 4 channel) from Kvaser (http://www.kvaser.com). +config CAN_AT91 + tristate "Atmel AT91 onchip CAN controller" + depends on CAN && CAN_DEV && ARCH_AT91SAM9263 + ---help--- + This is a driver for the SoC CAN controller in Atmel's AT91SAM9263. + config CAN_DEBUG_DEVICES bool "CAN devices debugging messages" depends on CAN diff --git a/drivers/net/can/Makefile b/drivers/net/can/Makefile index 523a941b358..0dea62721f2 100644 --- a/drivers/net/can/Makefile +++ b/drivers/net/can/Makefile @@ -7,6 +7,9 @@ obj-$(CONFIG_CAN_VCAN) += vcan.o obj-$(CONFIG_CAN_DEV) += can-dev.o can-dev-y := dev.o +obj-y += usb/ + obj-$(CONFIG_CAN_SJA1000) += sja1000/ +obj-$(CONFIG_CAN_AT91) += at91_can.o ccflags-$(CONFIG_CAN_DEBUG_DEVICES) := -DDEBUG diff --git a/drivers/net/can/at91_can.c b/drivers/net/can/at91_can.c new file mode 100644 index 00000000000..f67ae285a35 --- /dev/null +++ b/drivers/net/can/at91_can.c @@ -0,0 +1,1186 @@ +/* + * at91_can.c - CAN network driver for AT91 SoC CAN controller + * + * (C) 2007 by Hans J. Koch <hjk@linutronix.de> + * (C) 2008, 2009 by Marc Kleine-Budde <kernel@pengutronix.de> + * + * This software may be distributed under the terms of the GNU General + * Public License ("GPL") version 2 as distributed in the 'COPYING' + * file from the main directory of the linux kernel source. + * + * Send feedback to <socketcan-users@lists.berlios.de> + * + * + * Your platform definition file should specify something like: + * + * static struct at91_can_data ek_can_data = { + * transceiver_switch = sam9263ek_transceiver_switch, + * }; + * + * at91_add_device_can(&ek_can_data); + * + */ + +#include <linux/clk.h> +#include <linux/errno.h> +#include <linux/if_arp.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/platform_device.h> +#include <linux/skbuff.h> +#include <linux/spinlock.h> +#include <linux/string.h> +#include <linux/types.h> + +#include <linux/can.h> +#include <linux/can/dev.h> +#include <linux/can/error.h> + +#include <mach/board.h> + +#define DRV_NAME "at91_can" +#define AT91_NAPI_WEIGHT 12 + +/* + * RX/TX Mailbox split + * don't dare to touch + */ +#define AT91_MB_RX_NUM 12 +#define AT91_MB_TX_SHIFT 2 + +#define AT91_MB_RX_FIRST 0 +#define AT91_MB_RX_LAST (AT91_MB_RX_FIRST + AT91_MB_RX_NUM - 1) + +#define AT91_MB_RX_MASK(i) ((1 << (i)) - 1) +#define AT91_MB_RX_SPLIT 8 +#define AT91_MB_RX_LOW_LAST (AT91_MB_RX_SPLIT - 1) +#define AT91_MB_RX_LOW_MASK (AT91_MB_RX_MASK(AT91_MB_RX_SPLIT)) + +#define AT91_MB_TX_NUM (1 << AT91_MB_TX_SHIFT) +#define AT91_MB_TX_FIRST (AT91_MB_RX_LAST + 1) +#define AT91_MB_TX_LAST (AT91_MB_TX_FIRST + AT91_MB_TX_NUM - 1) + +#define AT91_NEXT_PRIO_SHIFT (AT91_MB_TX_SHIFT) +#define AT91_NEXT_PRIO_MASK (0xf << AT91_MB_TX_SHIFT) +#define AT91_NEXT_MB_MASK (AT91_MB_TX_NUM - 1) +#define AT91_NEXT_MASK ((AT91_MB_TX_NUM - 1) | AT91_NEXT_PRIO_MASK) + +/* Common registers */ +enum at91_reg { + AT91_MR = 0x000, + AT91_IER = 0x004, + AT91_IDR = 0x008, + AT91_IMR = 0x00C, + AT91_SR = 0x010, + AT91_BR = 0x014, + AT91_TIM = 0x018, + AT91_TIMESTP = 0x01C, + AT91_ECR = 0x020, + AT91_TCR = 0x024, + AT91_ACR = 0x028, +}; + +/* Mailbox registers (0 <= i <= 15) */ +#define AT91_MMR(i) (enum at91_reg)(0x200 + ((i) * 0x20)) +#define AT91_MAM(i) (enum at91_reg)(0x204 + ((i) * 0x20)) +#define AT91_MID(i) (enum at91_reg)(0x208 + ((i) * 0x20)) +#define AT91_MFID(i) (enum at91_reg)(0x20C + ((i) * 0x20)) +#define AT91_MSR(i) (enum at91_reg)(0x210 + ((i) * 0x20)) +#define AT91_MDL(i) (enum at91_reg)(0x214 + ((i) * 0x20)) +#define AT91_MDH(i) (enum at91_reg)(0x218 + ((i) * 0x20)) +#define AT91_MCR(i) (enum at91_reg)(0x21C + ((i) * 0x20)) + +/* Register bits */ +#define AT91_MR_CANEN BIT(0) +#define AT91_MR_LPM BIT(1) +#define AT91_MR_ABM BIT(2) +#define AT91_MR_OVL BIT(3) +#define AT91_MR_TEOF BIT(4) +#define AT91_MR_TTM BIT(5) +#define AT91_MR_TIMFRZ BIT(6) +#define AT91_MR_DRPT BIT(7) + +#define AT91_SR_RBSY BIT(29) + +#define AT91_MMR_PRIO_SHIFT (16) + +#define AT91_MID_MIDE BIT(29) + +#define AT91_MSR_MRTR BIT(20) +#define AT91_MSR_MABT BIT(22) +#define AT91_MSR_MRDY BIT(23) +#define AT91_MSR_MMI BIT(24) + +#define AT91_MCR_MRTR BIT(20) +#define AT91_MCR_MTCR BIT(23) + +/* Mailbox Modes */ +enum at91_mb_mode { + AT91_MB_MODE_DISABLED = 0, + AT91_MB_MODE_RX = 1, + AT91_MB_MODE_RX_OVRWR = 2, + AT91_MB_MODE_TX = 3, + AT91_MB_MODE_CONSUMER = 4, + AT91_MB_MODE_PRODUCER = 5, +}; + +/* Interrupt mask bits */ +#define AT91_IRQ_MB_RX ((1 << (AT91_MB_RX_LAST + 1)) \ + - (1 << AT91_MB_RX_FIRST)) +#define AT91_IRQ_MB_TX ((1 << (AT91_MB_TX_LAST + 1)) \ + - (1 << AT91_MB_TX_FIRST)) +#define AT91_IRQ_MB_ALL (AT91_IRQ_MB_RX | AT91_IRQ_MB_TX) + +#define AT91_IRQ_ERRA (1 << 16) +#define AT91_IRQ_WARN (1 << 17) +#define AT91_IRQ_ERRP (1 << 18) +#define AT91_IRQ_BOFF (1 << 19) +#define AT91_IRQ_SLEEP (1 << 20) +#define AT91_IRQ_WAKEUP (1 << 21) +#define AT91_IRQ_TOVF (1 << 22) +#define AT91_IRQ_TSTP (1 << 23) +#define AT91_IRQ_CERR (1 << 24) +#define AT91_IRQ_SERR (1 << 25) +#define AT91_IRQ_AERR (1 << 26) +#define AT91_IRQ_FERR (1 << 27) +#define AT91_IRQ_BERR (1 << 28) + +#define AT91_IRQ_ERR_ALL (0x1fff0000) +#define AT91_IRQ_ERR_FRAME (AT91_IRQ_CERR | AT91_IRQ_SERR | \ + AT91_IRQ_AERR | AT91_IRQ_FERR | AT91_IRQ_BERR) +#define AT91_IRQ_ERR_LINE (AT91_IRQ_ERRA | AT91_IRQ_WARN | \ + AT91_IRQ_ERRP | AT91_IRQ_BOFF) + +#define AT91_IRQ_ALL (0x1fffffff) + +struct at91_priv { + struct can_priv can; /* must be the first member! */ + struct net_device *dev; + struct napi_struct napi; + + void __iomem *reg_base; + + u32 reg_sr; + unsigned int tx_next; + unsigned int tx_echo; + unsigned int rx_next; + + struct clk *clk; + struct at91_can_data *pdata; +}; + +static struct can_bittiming_const at91_bittiming_const = { + .tseg1_min = 4, + .tseg1_max = 16, + .tseg2_min = 2, + .tseg2_max = 8, + .sjw_max = 4, + .brp_min = 2, + .brp_max = 128, + .brp_inc = 1, +}; + +static inline int get_tx_next_mb(const struct at91_priv *priv) +{ + return (priv->tx_next & AT91_NEXT_MB_MASK) + AT91_MB_TX_FIRST; +} + +static inline int get_tx_next_prio(const struct at91_priv *priv) +{ + return (priv->tx_next >> AT91_NEXT_PRIO_SHIFT) & 0xf; +} + +static inline int get_tx_echo_mb(const struct at91_priv *priv) +{ + return (priv->tx_echo & AT91_NEXT_MB_MASK) + AT91_MB_TX_FIRST; +} + +static inline u32 at91_read(const struct at91_priv *priv, enum at91_reg reg) +{ + return readl(priv->reg_base + reg); +} + +static inline void at91_write(const struct at91_priv *priv, enum at91_reg reg, + u32 value) +{ + writel(value, priv->reg_base + reg); +} + +static inline void set_mb_mode_prio(const struct at91_priv *priv, + unsigned int mb, enum at91_mb_mode mode, int prio) +{ + at91_write(priv, AT91_MMR(mb), (mode << 24) | (prio << 16)); +} + +static inline void set_mb_mode(const struct at91_priv *priv, unsigned int mb, + enum at91_mb_mode mode) +{ + set_mb_mode_prio(priv, mb, mode, 0); +} + +static struct sk_buff *alloc_can_skb(struct net_device *dev, + struct can_frame **cf) +{ + struct sk_buff *skb; + + skb = netdev_alloc_skb(dev, sizeof(struct can_frame)); + if (unlikely(!skb)) + return NULL; + + skb->protocol = htons(ETH_P_CAN); + skb->ip_summed = CHECKSUM_UNNECESSARY; + *cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame)); + + return skb; +} + +static struct sk_buff *alloc_can_err_skb(struct net_device *dev, + struct can_frame **cf) +{ + struct sk_buff *skb; + + skb = alloc_can_skb(dev, cf); + if (unlikely(!skb)) + return NULL; + + memset(*cf, 0, sizeof(struct can_frame)); + (*cf)->can_id = CAN_ERR_FLAG; + (*cf)->can_dlc = CAN_ERR_DLC; + + return skb; +} + +/* + * Swtich transceiver on or off + */ +static void at91_transceiver_switch(const struct at91_priv *priv, int on) +{ + if (priv->pdata && priv->pdata->transceiver_switch) + priv->pdata->transceiver_switch(on); +} + +static void at91_setup_mailboxes(struct net_device *dev) +{ + struct at91_priv *priv = netdev_priv(dev); + unsigned int i; + + /* + * The first 12 mailboxes are used as a reception FIFO. The + * last mailbox is configured with overwrite option. The + * overwrite flag indicates a FIFO overflow. + */ + for (i = AT91_MB_RX_FIRST; i < AT91_MB_RX_LAST; i++) + set_mb_mode(priv, i, AT91_MB_MODE_RX); + set_mb_mode(priv, AT91_MB_RX_LAST, AT91_MB_MODE_RX_OVRWR); + + /* The last 4 mailboxes are used for transmitting. */ + for (i = AT91_MB_TX_FIRST; i <= AT91_MB_TX_LAST; i++) + set_mb_mode_prio(priv, i, AT91_MB_MODE_TX, 0); + + /* Reset tx and rx helper pointers */ + priv->tx_next = priv->tx_echo = priv->rx_next = 0; +} + +static int at91_set_bittiming(struct net_device *dev) +{ + const struct at91_priv *priv = netdev_priv(dev); + const struct can_bittiming *bt = &priv->can.bittiming; + u32 reg_br; + + reg_br = ((priv->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) << 24) | + ((bt->brp - 1) << 16) | ((bt->sjw - 1) << 12) | + ((bt->prop_seg - 1) << 8) | ((bt->phase_seg1 - 1) << 4) | + ((bt->phase_seg2 - 1) << 0); + + dev_info(dev->dev.parent, "writing AT91_BR: 0x%08x\n", reg_br); + + at91_write(priv, AT91_BR, reg_br); + + return 0; +} + +static void at91_chip_start(struct net_device *dev) +{ + struct at91_priv *priv = netdev_priv(dev); + u32 reg_mr, reg_ier; + + /* disable interrupts */ + at91_write(priv, AT91_IDR, AT91_IRQ_ALL); + + /* disable chip */ + reg_mr = at91_read(priv, AT91_MR); + at91_write(priv, AT91_MR, reg_mr & ~AT91_MR_CANEN); + + at91_setup_mailboxes(dev); + at91_transceiver_switch(priv, 1); + + /* enable chip */ + at91_write(priv, AT91_MR, AT91_MR_CANEN); + + priv->can.state = CAN_STATE_ERROR_ACTIVE; + + /* Enable interrupts */ + reg_ier = AT91_IRQ_MB_RX | AT91_IRQ_ERRP | AT91_IRQ_ERR_FRAME; + at91_write(priv, AT91_IDR, AT91_IRQ_ALL); + at91_write(priv, AT91_IER, reg_ier); +} + +static void at91_chip_stop(struct net_device *dev, enum can_state state) +{ + struct at91_priv *priv = netdev_priv(dev); + u32 reg_mr; + + /* disable interrupts */ + at91_write(priv, AT91_IDR, AT91_IRQ_ALL); + + reg_mr = at91_read(priv, AT91_MR); + at91_write(priv, AT91_MR, reg_mr & ~AT91_MR_CANEN); + + at91_transceiver_switch(priv, 0); + priv->can.state = state; +} + +/* + * theory of operation: + * + * According to the datasheet priority 0 is the highest priority, 15 + * is the lowest. If two mailboxes have the same priority level the + * message of the mailbox with the lowest number is sent first. + * + * We use the first TX mailbox (AT91_MB_TX_FIRST) with prio 0, then + * the next mailbox with prio 0, and so on, until all mailboxes are + * used. Then we start from the beginning with mailbox + * AT91_MB_TX_FIRST, but with prio 1, mailbox AT91_MB_TX_FIRST + 1 + * prio 1. When we reach the last mailbox with prio 15, we have to + * stop sending, waiting for all messages to be delivered, then start + * again with mailbox AT91_MB_TX_FIRST prio 0. + * + * We use the priv->tx_next as counter for the next transmission + * mailbox, but without the offset AT91_MB_TX_FIRST. The lower bits + * encode the mailbox number, the upper 4 bits the mailbox priority: + * + * priv->tx_next = (prio << AT91_NEXT_PRIO_SHIFT) || + * (mb - AT91_MB_TX_FIRST); + * + */ +static netdev_tx_t at91_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct at91_priv *priv = netdev_priv(dev); + struct net_device_stats *stats = &dev->stats; + struct can_frame *cf = (struct can_frame *)skb->data; + unsigned int mb, prio; + u32 reg_mid, reg_mcr; + + mb = get_tx_next_mb(priv); + prio = get_tx_next_prio(priv); + + if (unlikely(!(at91_read(priv, AT91_MSR(mb)) & AT91_MSR_MRDY))) { + netif_stop_queue(dev); + + dev_err(dev->dev.parent, + "BUG! TX buffer full when queue awake!\n"); + return NETDEV_TX_BUSY; + } + + if (cf->can_id & CAN_EFF_FLAG) + reg_mid = (cf->can_id & CAN_EFF_MASK) | AT91_MID_MIDE; + else + reg_mid = (cf->can_id & CAN_SFF_MASK) << 18; + + reg_mcr = ((cf->can_id & CAN_RTR_FLAG) ? AT91_MCR_MRTR : 0) | + (cf->can_dlc << 16) | AT91_MCR_MTCR; + + /* disable MB while writing ID (see datasheet) */ + set_mb_mode(priv, mb, AT91_MB_MODE_DISABLED); + at91_write(priv, AT91_MID(mb), reg_mid); + set_mb_mode_prio(priv, mb, AT91_MB_MODE_TX, prio); + + at91_write(priv, AT91_MDL(mb), *(u32 *)(cf->data + 0)); + at91_write(priv, AT91_MDH(mb), *(u32 *)(cf->data + 4)); + + /* This triggers transmission */ + at91_write(priv, AT91_MCR(mb), reg_mcr); + + stats->tx_bytes += cf->can_dlc; + dev->trans_start = jiffies; + + /* _NOTE_: substract AT91_MB_TX_FIRST offset from mb! */ + can_put_echo_skb(skb, dev, mb - AT91_MB_TX_FIRST); + + /* + * we have to stop the queue and deliver all messages in case + * of a prio+mb counter wrap around. This is the case if + * tx_next buffer prio and mailbox equals 0. + * + * also stop the queue if next buffer is still in use + * (== not ready) + */ + priv->tx_next++; + if (!(at91_read(priv, AT91_MSR(get_tx_next_mb(priv))) & + AT91_MSR_MRDY) || + (priv->tx_next & AT91_NEXT_MASK) == 0) + netif_stop_queue(dev); + + /* Enable interrupt for this mailbox */ + at91_write(priv, AT91_IER, 1 << mb); + + return NETDEV_TX_OK; +} + +/** + * at91_activate_rx_low - activate lower rx mailboxes + * @priv: a91 context + * + * Reenables the lower mailboxes for reception of new CAN messages + */ +static inline void at91_activate_rx_low(const struct at91_priv *priv) +{ + u32 mask = AT91_MB_RX_LOW_MASK; + at91_write(priv, AT91_TCR, mask); +} + +/** + * at91_activate_rx_mb - reactive single rx mailbox + * @priv: a91 context + * @mb: mailbox to reactivate + * + * Reenables given mailbox for reception of new CAN messages + */ +static inline void at91_activate_rx_mb(const struct at91_priv *priv, + unsigned int mb) +{ + u32 mask = 1 << mb; + at91_write(priv, AT91_TCR, mask); +} + +/** + * at91_rx_overflow_err - send error frame due to rx overflow + * @dev: net device + */ +static void at91_rx_overflow_err(struct net_device *dev) +{ + struct net_device_stats *stats = &dev->stats; + struct sk_buff *skb; + struct can_frame *cf; + + dev_dbg(dev->dev.parent, "RX buffer overflow\n"); + stats->rx_over_errors++; + stats->rx_errors++; + + skb = alloc_can_err_skb(dev, &cf); + if (unlikely(!skb)) + return; + + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; + netif_receive_skb(skb); + + stats->rx_packets++; + stats->rx_bytes += cf->can_dlc; +} + +/** + * at91_read_mb - read CAN msg from mailbox (lowlevel impl) + * @dev: net device + * @mb: mailbox number to read from + * @cf: can frame where to store message + * + * Reads a CAN message from the given mailbox and stores data into + * given can frame. "mb" and "cf" must be valid. + */ +static void at91_read_mb(struct net_device *dev, unsigned int mb, + struct can_frame *cf) +{ + const struct at91_priv *priv = netdev_priv(dev); + u32 reg_msr, reg_mid; + + reg_mid = at91_read(priv, AT91_MID(mb)); + if (reg_mid & AT91_MID_MIDE) + cf->can_id = ((reg_mid >> 0) & CAN_EFF_MASK) | CAN_EFF_FLAG; + else + cf->can_id = (reg_mid >> 18) & CAN_SFF_MASK; + + reg_msr = at91_read(priv, AT91_MSR(mb)); + if (reg_msr & AT91_MSR_MRTR) + cf->can_id |= CAN_RTR_FLAG; + cf->can_dlc = min_t(__u8, (reg_msr >> 16) & 0xf, 8); + + *(u32 *)(cf->data + 0) = at91_read(priv, AT91_MDL(mb)); + *(u32 *)(cf->data + 4) = at91_read(priv, AT91_MDH(mb)); + + if (unlikely(mb == AT91_MB_RX_LAST && reg_msr & AT91_MSR_MMI)) + at91_rx_overflow_err(dev); +} + +/** + * at91_read_msg - read CAN message from mailbox + * @dev: net device + * @mb: mail box to read from + * + * Reads a CAN message from given mailbox, and put into linux network + * RX queue, does all housekeeping chores (stats, ...) + */ +static void at91_read_msg(struct net_device *dev, unsigned int mb) +{ + struct net_device_stats *stats = &dev->stats; + struct can_frame *cf; + struct sk_buff *skb; + + skb = alloc_can_skb(dev, &cf); + if (unlikely(!skb)) { + stats->rx_dropped++; + return; + } + + at91_read_mb(dev, mb, cf); + netif_receive_skb(skb); + + stats->rx_packets++; + stats->rx_bytes += cf->can_dlc; +} + +/** + * at91_poll_rx - read multiple CAN messages from mailboxes + * @dev: net device + * @quota: max number of pkgs we're allowed to receive + * + * Theory of Operation: + * + * 12 of the 16 mailboxes on the chip are reserved for RX. we split + * them into 2 groups. The lower group holds 8 and upper 4 mailboxes. + * + * Like it or not, but the chip always saves a received CAN message + * into the first free mailbox it finds (starting with the + * lowest). This makes it very difficult to read the messages in the + * right order from the chip. This is how we work around that problem: + * + * The first message goes into mb nr. 0 and issues an interrupt. All + * rx ints are disabled in the interrupt handler and a napi poll is + * scheduled. We read the mailbox, but do _not_ reenable the mb (to + * receive another message). + * + * lower mbxs upper + * ______^______ __^__ + * / \ / \ + * +-+-+-+-+-+-+-+-++-+-+-+-+ + * |x|x|x|x|x|x|x|x|| | | | | + * +-+-+-+-+-+-+-+-++-+-+-+-+ + * 0 0 0 0 0 0 0 0 0 0 1 1 \ mail + * 0 1 2 3 4 5 6 7 8 9 0 1 / box + * + * The variable priv->rx_next points to the next mailbox to read a + * message from. As long we're in the lower mailboxes we just read the + * mailbox but not reenable it. + * + * With completion of the last of the lower mailboxes, we reenable the + * whole first group, but continue to look for filled mailboxes in the + * upper mailboxes. Imagine the second group like overflow mailboxes, + * which takes CAN messages if the lower goup is full. While in the + * upper group we reenable the mailbox right after reading it. Giving + * the chip more room to store messages. + * + * After finishing we look again in the lower group if we've still + * quota. + * + */ +static int at91_poll_rx(struct net_device *dev, int quota) +{ + struct at91_priv *priv = netdev_priv(dev); + u32 reg_sr = at91_read(priv, AT91_SR); + const unsigned long *addr = (unsigned long *)®_sr; + unsigned int mb; + int received = 0; + + if (priv->rx_next > AT91_MB_RX_LOW_LAST && + reg_sr & AT91_MB_RX_LOW_MASK) + dev_info(dev->dev.parent, + "order of incoming frames cannot be guaranteed\n"); + + again: + for (mb = find_next_bit(addr, AT91_MB_RX_NUM, priv->rx_next); + mb < AT91_MB_RX_NUM && quota > 0; + reg_sr = at91_read(priv, AT91_SR), + mb = find_next_bit(addr, AT91_MB_RX_NUM, ++priv->rx_next)) { + at91_read_msg(dev, mb); + + /* reactivate mailboxes */ + if (mb == AT91_MB_RX_LOW_LAST) + /* all lower mailboxed, if just finished it */ + at91_activate_rx_low(priv); + else if (mb > AT91_MB_RX_LOW_LAST) + /* only the mailbox we read */ + at91_activate_rx_mb(priv, mb); + + received++; + quota--; + } + + /* upper group completed, look again in lower */ + if (priv->rx_next > AT91_MB_RX_LOW_LAST && + quota > 0 && mb >= AT91_MB_RX_NUM) { + priv->rx_next = 0; + goto again; + } + + return received; +} + +static void at91_poll_err_frame(struct net_device *dev, + struct can_frame *cf, u32 reg_sr) +{ + struct at91_priv *priv = netdev_priv(dev); + + /* CRC error */ + if (reg_sr & AT91_IRQ_CERR) { + dev_dbg(dev->dev.parent, "CERR irq\n"); + dev->stats.rx_errors++; + priv->can.can_stats.bus_error++; + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; + } + + /* Stuffing Error */ + if (reg_sr & AT91_IRQ_SERR) { + dev_dbg(dev->dev.parent, "SERR irq\n"); + dev->stats.rx_errors++; + priv->can.can_stats.bus_error++; + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; + cf->data[2] |= CAN_ERR_PROT_STUFF; + } + + /* Acknowledgement Error */ + if (reg_sr & AT91_IRQ_AERR) { + dev_dbg(dev->dev.parent, "AERR irq\n"); + dev->stats.tx_errors++; + cf->can_id |= CAN_ERR_ACK; + } + + /* Form error */ + if (reg_sr & AT91_IRQ_FERR) { + dev_dbg(dev->dev.parent, "FERR irq\n"); + dev->stats.rx_errors++; + priv->can.can_stats.bus_error++; + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; + cf->data[2] |= CAN_ERR_PROT_FORM; + } + + /* Bit Error */ + if (reg_sr & AT91_IRQ_BERR) { + dev_dbg(dev->dev.parent, "BERR irq\n"); + dev->stats.tx_errors++; + priv->can.can_stats.bus_error++; + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; + cf->data[2] |= CAN_ERR_PROT_BIT; + } +} + +static int at91_poll_err(struct net_device *dev, int quota, u32 reg_sr) +{ + struct sk_buff *skb; + struct can_frame *cf; + + if (quota == 0) + return 0; + + skb = alloc_can_err_skb(dev, &cf); + if (unlikely(!skb)) + return 0; + + at91_poll_err_frame(dev, cf, reg_sr); + netif_receive_skb(skb); + + dev->last_rx = jiffies; + dev->stats.rx_packets++; + dev->stats.rx_bytes += cf->can_dlc; + + return 1; +} + +static int at91_poll(struct napi_struct *napi, int quota) +{ + struct net_device *dev = napi->dev; + const struct at91_priv *priv = netdev_priv(dev); + u32 reg_sr = at91_read(priv, AT91_SR); + int work_done = 0; + + if (reg_sr & AT91_IRQ_MB_RX) + work_done += at91_poll_rx(dev, quota - work_done); + + /* + * The error bits are clear on read, + * so use saved value from irq handler. + */ + reg_sr |= priv->reg_sr; + if (reg_sr & AT91_IRQ_ERR_FRAME) + work_done += at91_poll_err(dev, quota - work_done, reg_sr); + + if (work_done < quota) { + /* enable IRQs for frame errors and all mailboxes >= rx_next */ + u32 reg_ier = AT91_IRQ_ERR_FRAME; + reg_ier |= AT91_IRQ_MB_RX & ~AT91_MB_RX_MASK(priv->rx_next); + + napi_complete(napi); + at91_write(priv, AT91_IER, reg_ier); + } + + return work_done; +} + +/* + * theory of operation: + * + * priv->tx_echo holds the number of the oldest can_frame put for + * transmission into the hardware, but not yet ACKed by the CAN tx + * complete IRQ. + * + * We iterate from priv->tx_echo to priv->tx_next and check if the + * packet has been transmitted, echo it back to the CAN framework. If + * we discover a not yet transmitted package, stop looking for more. + * + */ +static void at91_irq_tx(struct net_device *dev, u32 reg_sr) +{ + struct at91_priv *priv = netdev_priv(dev); + u32 reg_msr; + unsigned int mb; + + /* masking of reg_sr not needed, already done by at91_irq */ + + for (/* nix */; (priv->tx_next - priv->tx_echo) > 0; priv->tx_echo++) { + mb = get_tx_echo_mb(priv); + + /* no event in mailbox? */ + if (!(reg_sr & (1 << mb))) + break; + + /* Disable irq for this TX mailbox */ + at91_write(priv, AT91_IDR, 1 << mb); + + /* + * only echo if mailbox signals us a transfer + * complete (MSR_MRDY). Otherwise it's a tansfer + * abort. "can_bus_off()" takes care about the skbs + * parked in the echo queue. + */ + reg_msr = at91_read(priv, AT91_MSR(mb)); + if (likely(reg_msr & AT91_MSR_MRDY && + ~reg_msr & AT91_MSR_MABT)) { + /* _NOTE_: substract AT91_MB_TX_FIRST offset from mb! */ + can_get_echo_skb(dev, mb - AT91_MB_TX_FIRST); + dev->stats.tx_packets++; + } + } + + /* + * restart queue if we don't have a wrap around but restart if + * we get a TX int for the last can frame directly before a + * wrap around. + */ + if ((priv->tx_next & AT91_NEXT_MASK) != 0 || + (priv->tx_echo & AT91_NEXT_MASK) == 0) + netif_wake_queue(dev); +} + +static void at91_irq_err_state(struct net_device *dev, + struct can_frame *cf, enum can_state new_state) +{ + struct at91_priv *priv = netdev_priv(dev); + u32 reg_idr, reg_ier, reg_ecr; + u8 tec, rec; + + reg_ecr = at91_read(priv, AT91_ECR); + rec = reg_ecr & 0xff; + tec = reg_ecr >> 16; + + switch (priv->can.state) { + case CAN_STATE_ERROR_ACTIVE: + /* + * from: ERROR_ACTIVE + * to : ERROR_WARNING, ERROR_PASSIVE, BUS_OFF + * => : there was a warning int + */ + if (new_state >= CAN_STATE_ERROR_WARNING && + new_state <= CAN_STATE_BUS_OFF) { + dev_dbg(dev->dev.parent, "Error Warning IRQ\n"); + priv->can.can_stats.error_warning++; + + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] = (tec > rec) ? + CAN_ERR_CRTL_TX_WARNING : + CAN_ERR_CRTL_RX_WARNING; + } + case CAN_STATE_ERROR_WARNING: /* fallthrough */ + /* + * from: ERROR_ACTIVE, ERROR_WARNING + * to : ERROR_PASSIVE, BUS_OFF + * => : error passive int + */ + if (new_state >= CAN_STATE_ERROR_PASSIVE && + new_state <= CAN_STATE_BUS_OFF) { + dev_dbg(dev->dev.parent, "Error Passive IRQ\n"); + priv->can.can_stats.error_passive++; + + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] = (tec > rec) ? + CAN_ERR_CRTL_TX_PASSIVE : + CAN_ERR_CRTL_RX_PASSIVE; + } + break; + case CAN_STATE_BUS_OFF: + /* + * from: BUS_OFF + * to : ERROR_ACTIVE, ERROR_WARNING, ERROR_PASSIVE + */ + if (new_state <= CAN_STATE_ERROR_PASSIVE) { + cf->can_id |= CAN_ERR_RESTARTED; + + dev_dbg(dev->dev.parent, "restarted\n"); + priv->can.can_stats.restarts++; + + netif_carrier_on(dev); + netif_wake_queue(dev); + } + break; + default: + break; + } + + + /* process state changes depending on the new state */ + switch (new_state) { + case CAN_STATE_ERROR_ACTIVE: + /* + * actually we want to enable AT91_IRQ_WARN here, but + * it screws up the system under certain + * circumstances. so just enable AT91_IRQ_ERRP, thus + * the "fallthrough" + */ + dev_dbg(dev->dev.parent, "Error Active\n"); + cf->can_id |= CAN_ERR_PROT; + cf->data[2] = CAN_ERR_PROT_ACTIVE; + case CAN_STATE_ERROR_WARNING: /* fallthrough */ + reg_idr = AT91_IRQ_ERRA | AT91_IRQ_WARN | AT91_IRQ_BOFF; + reg_ier = AT91_IRQ_ERRP; + break; + case CAN_STATE_ERROR_PASSIVE: + reg_idr = AT91_IRQ_ERRA | AT91_IRQ_WARN | AT91_IRQ_ERRP; + reg_ier = AT91_IRQ_BOFF; + break; + case CAN_STATE_BUS_OFF: + reg_idr = AT91_IRQ_ERRA | AT91_IRQ_ERRP | + AT91_IRQ_WARN | AT91_IRQ_BOFF; + reg_ier = 0; + + cf->can_id |= CAN_ERR_BUSOFF; + + dev_dbg(dev->dev.parent, "bus-off\n"); + netif_carrier_off(dev); + priv->can.can_stats.bus_off++; + + /* turn off chip, if restart is disabled */ + if (!priv->can.restart_ms) { + at91_chip_stop(dev, CAN_STATE_BUS_OFF); + return; + } + break; + default: + break; + } + + at91_write(priv, AT91_IDR, reg_idr); + at91_write(priv, AT91_IER, reg_ier); +} + +static void at91_irq_err(struct net_device *dev) +{ + struct at91_priv *priv = netdev_priv(dev); + struct sk_buff *skb; + struct can_frame *cf; + enum can_state new_state; + u32 reg_sr; + + reg_sr = at91_read(priv, AT91_SR); + + /* we need to look at the unmasked reg_sr */ + if (unlikely(reg_sr & AT91_IRQ_BOFF)) + new_state = CAN_STATE_BUS_OFF; + else if (unlikely(reg_sr & AT91_IRQ_ERRP)) + new_state = CAN_STATE_ERROR_PASSIVE; + else if (unlikely(reg_sr & AT91_IRQ_WARN)) + new_state = CAN_STATE_ERROR_WARNING; + else if (likely(reg_sr & AT91_IRQ_ERRA)) + new_state = CAN_STATE_ERROR_ACTIVE; + else { + dev_err(dev->dev.parent, "BUG! hardware in undefined state\n"); + return; + } + + /* state hasn't changed */ + if (likely(new_state == priv->can.state)) + return; + + skb = alloc_can_err_skb(dev, &cf); + if (unlikely(!skb)) + return; + + at91_irq_err_state(dev, cf, new_state); + netif_rx(skb); + + dev->last_rx = jiffies; + dev->stats.rx_packets++; + dev->stats.rx_bytes += cf->can_dlc; + + priv->can.state = new_state; +} + +/* + * interrupt handler + */ +static irqreturn_t at91_irq(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct at91_priv *priv = netdev_priv(dev); + irqreturn_t handled = IRQ_NONE; + u32 reg_sr, reg_imr; + + reg_sr = at91_read(priv, AT91_SR); + reg_imr = at91_read(priv, AT91_IMR); + + /* Ignore masked interrupts */ + reg_sr &= reg_imr; + if (!reg_sr) + goto exit; + + handled = IRQ_HANDLED; + + /* Receive or error interrupt? -> napi */ + if (reg_sr & (AT91_IRQ_MB_RX | AT91_IRQ_ERR_FRAME)) { + /* + * The error bits are clear on read, + * save for later use. + */ + priv->reg_sr = reg_sr; + at91_write(priv, AT91_IDR, + AT91_IRQ_MB_RX | AT91_IRQ_ERR_FRAME); + napi_schedule(&priv->napi); + } + + /* Transmission complete interrupt */ + if (reg_sr & AT91_IRQ_MB_TX) + at91_irq_tx(dev, reg_sr); + + at91_irq_err(dev); + + exit: + return handled; +} + +static int at91_open(struct net_device *dev) +{ + struct at91_priv *priv = netdev_priv(dev); + int err; + + clk_enable(priv->clk); + + /* check or determine and set bittime */ + err = open_candev(dev); + if (err) + goto out; + + /* register interrupt handler */ + if (request_irq(dev->irq, at91_irq, IRQF_SHARED, + dev->name, dev)) { + err = -EAGAIN; + goto out_close; + } + + /* start chip and queuing */ + at91_chip_start(dev); + napi_enable(&priv->napi); + netif_start_queue(dev); + + return 0; + + out_close: + close_candev(dev); + out: + clk_disable(priv->clk); + + return err; +} + +/* + * stop CAN bus activity + */ +static int at91_close(struct net_device *dev) +{ + struct at91_priv *priv = netdev_priv(dev); + + netif_stop_queue(dev); + napi_disable(&priv->napi); + at91_chip_stop(dev, CAN_STATE_STOPPED); + + free_irq(dev->irq, dev); + clk_disable(priv->clk); + + close_candev(dev); + + return 0; +} + +static int at91_set_mode(struct net_device *dev, enum can_mode mode) +{ + switch (mode) { + case CAN_MODE_START: + at91_chip_start(dev); + netif_wake_queue(dev); + break; + + default: + return -EOPNOTSUPP; + } + + return 0; +} + +static const struct net_device_ops at91_netdev_ops = { + .ndo_open = at91_open, + .ndo_stop = at91_close, + .ndo_start_xmit = at91_start_xmit, +}; + +static int __init at91_can_probe(struct platform_device *pdev) +{ + struct net_device *dev; + struct at91_priv *priv; + struct resource *res; + struct clk *clk; + void __iomem *addr; + int err, irq; + + clk = clk_get(&pdev->dev, "can_clk"); + if (IS_ERR(clk)) { + dev_err(&pdev->dev, "no clock defined\n"); + err = -ENODEV; + goto exit; + } + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + irq = platform_get_irq(pdev, 0); + if (!res || !irq) { + err = -ENODEV; + goto exit_put; + } + + if (!request_mem_region(res->start, + resource_size(res), + pdev->name)) { + err = -EBUSY; + goto exit_put; + } + + addr = ioremap_nocache(res->start, resource_size(res)); + if (!addr) { + err = -ENOMEM; + goto exit_release; + } + + dev = alloc_candev(sizeof(struct at91_priv)); + if (!dev) { + err = -ENOMEM; + goto exit_iounmap; + } + + dev->netdev_ops = &at91_netdev_ops; + dev->irq = irq; + dev->flags |= IFF_ECHO; + + priv = netdev_priv(dev); + priv->can.clock.freq = clk_get_rate(clk); + priv->can.bittiming_const = &at91_bittiming_const; + priv->can.do_set_bittiming = at91_set_bittiming; + priv->can.do_set_mode = at91_set_mode; + priv->reg_base = addr; + priv->dev = dev; + priv->clk = clk; + priv->pdata = pdev->dev.platform_data; + + netif_napi_add(dev, &priv->napi, at91_poll, AT91_NAPI_WEIGHT); + + dev_set_drvdata(&pdev->dev, dev); + SET_NETDEV_DEV(dev, &pdev->dev); + + err = register_candev(dev); + if (err) { + dev_err(&pdev->dev, "registering netdev failed\n"); + goto exit_free; + } + + dev_info(&pdev->dev, "device registered (reg_base=%p, irq=%d)\n", + priv->reg_base, dev->irq); + + return 0; + + exit_free: + free_netdev(dev); + exit_iounmap: + iounmap(addr); + exit_release: + release_mem_region(res->start, resource_size(res)); + exit_put: + clk_put(clk); + exit: + return err; +} + +static int __devexit at91_can_remove(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct at91_priv *priv = netdev_priv(dev); + struct resource *res; + + unregister_netdev(dev); + + platform_set_drvdata(pdev, NULL); + + free_netdev(dev); + + iounmap(priv->reg_base); + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + release_mem_region(res->start, resource_size(res)); + + clk_put(priv->clk); + + return 0; +} + +static struct platform_driver at91_can_driver = { + .probe = at91_can_probe, + .remove = __devexit_p(at91_can_remove), + .driver = { + .name = DRV_NAME, + .owner = THIS_MODULE, + }, +}; + +static int __init at91_can_module_init(void) +{ + printk(KERN_INFO "%s netdevice driver\n", DRV_NAME); + return platform_driver_register(&at91_can_driver); +} + +static void __exit at91_can_module_exit(void) +{ + platform_driver_unregister(&at91_can_driver); + printk(KERN_INFO "%s: driver removed\n", DRV_NAME); +} + +module_init(at91_can_module_init); +module_exit(at91_can_module_exit); + +MODULE_AUTHOR("Marc Kleine-Budde <mkl@pengutronix.de>"); +MODULE_LICENSE("GPL v2"); +MODULE_DESCRIPTION(DRV_NAME " CAN netdevice driver"); diff --git a/drivers/net/can/sja1000/ems_pci.c b/drivers/net/can/sja1000/ems_pci.c index 7d84b8ac9c1..fd04789d337 100644 --- a/drivers/net/can/sja1000/ems_pci.c +++ b/drivers/net/can/sja1000/ems_pci.c @@ -94,12 +94,14 @@ struct ems_pci_card { #define EMS_PCI_CDR (CDR_CBP | CDR_CLKOUT_MASK) #define EMS_PCI_V1_BASE_BAR 1 -#define EMS_PCI_V1_MEM_SIZE 4096 +#define EMS_PCI_V1_CONF_SIZE 4096 /* size of PITA control area */ #define EMS_PCI_V2_BASE_BAR 2 -#define EMS_PCI_V2_MEM_SIZE 128 +#define EMS_PCI_V2_CONF_SIZE 128 /* size of PLX control area */ #define EMS_PCI_CAN_BASE_OFFSET 0x400 /* offset where the controllers starts */ #define EMS_PCI_CAN_CTRL_SIZE 0x200 /* memory size for each controller */ +#define EMS_PCI_BASE_SIZE 4096 /* size of controller area */ + static struct pci_device_id ems_pci_tbl[] = { /* CPC-PCI v1 */ {PCI_VENDOR_ID_SIEMENS, 0x2104, PCI_ANY_ID, PCI_ANY_ID,}, @@ -224,7 +226,7 @@ static int __devinit ems_pci_add_card(struct pci_dev *pdev, struct sja1000_priv *priv; struct net_device *dev; struct ems_pci_card *card; - int max_chan, mem_size, base_bar; + int max_chan, conf_size, base_bar; int err, i; /* Enabling PCI device */ @@ -251,22 +253,22 @@ static int __devinit ems_pci_add_card(struct pci_dev *pdev, card->version = 2; /* CPC-PCI v2 */ max_chan = EMS_PCI_V2_MAX_CHAN; base_bar = EMS_PCI_V2_BASE_BAR; - mem_size = EMS_PCI_V2_MEM_SIZE; + conf_size = EMS_PCI_V2_CONF_SIZE; } else { card->version = 1; /* CPC-PCI v1 */ max_chan = EMS_PCI_V1_MAX_CHAN; base_bar = EMS_PCI_V1_BASE_BAR; - mem_size = EMS_PCI_V1_MEM_SIZE; + conf_size = EMS_PCI_V1_CONF_SIZE; } /* Remap configuration space and controller memory area */ - card->conf_addr = pci_iomap(pdev, 0, mem_size); + card->conf_addr = pci_iomap(pdev, 0, conf_size); if (card->conf_addr == NULL) { err = -ENOMEM; goto failure_cleanup; } - card->base_addr = pci_iomap(pdev, base_bar, mem_size); + card->base_addr = pci_iomap(pdev, base_bar, EMS_PCI_BASE_SIZE); if (card->base_addr == NULL) { err = -ENOMEM; goto failure_cleanup; diff --git a/drivers/net/can/usb/Makefile b/drivers/net/can/usb/Makefile new file mode 100644 index 00000000000..c3f75ba701b --- /dev/null +++ b/drivers/net/can/usb/Makefile @@ -0,0 +1,5 @@ +# +# Makefile for the Linux Controller Area Network USB drivers. +# + +obj-$(CONFIG_CAN_EMS_USB) += ems_usb.o diff --git a/drivers/net/can/usb/ems_usb.c b/drivers/net/can/usb/ems_usb.c new file mode 100644 index 00000000000..9012e0abc62 --- /dev/null +++ b/drivers/net/can/usb/ems_usb.c @@ -0,0 +1,1155 @@ +/* + * CAN driver for EMS Dr. Thomas Wuensche CPC-USB/ARM7 + * + * Copyright (C) 2004-2009 EMS Dr. Thomas Wuensche + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published + * by the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + * You should have received a copy of the GNU General Public License along + * with this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA. + */ +#include <linux/init.h> +#include <linux/signal.h> +#include <linux/slab.h> +#include <linux/module.h> +#include <linux/netdevice.h> +#include <linux/usb.h> + +#include <linux/can.h> +#include <linux/can/dev.h> +#include <linux/can/error.h> + +MODULE_AUTHOR("Sebastian Haas <haas@ems-wuensche.com>"); +MODULE_DESCRIPTION("CAN driver for EMS Dr. Thomas Wuensche CAN/USB interfaces"); +MODULE_LICENSE("GPL v2"); + +/* Control-Values for CPC_Control() Command Subject Selection */ +#define CONTR_CAN_MESSAGE 0x04 +#define CONTR_CAN_STATE 0x0C +#define CONTR_BUS_ERROR 0x1C + +/* Control Command Actions */ +#define CONTR_CONT_OFF 0 +#define CONTR_CONT_ON 1 +#define CONTR_ONCE 2 + +/* Messages from CPC to PC */ +#define CPC_MSG_TYPE_CAN_FRAME 1 /* CAN data frame */ +#define CPC_MSG_TYPE_RTR_FRAME 8 /* CAN remote frame */ +#define CPC_MSG_TYPE_CAN_PARAMS 12 /* Actual CAN parameters */ +#define CPC_MSG_TYPE_CAN_STATE 14 /* CAN state message */ +#define CPC_MSG_TYPE_EXT_CAN_FRAME 16 /* Extended CAN data frame */ +#define CPC_MSG_TYPE_EXT_RTR_FRAME 17 /* Extended remote frame */ +#define CPC_MSG_TYPE_CONTROL 19 /* change interface behavior */ +#define CPC_MSG_TYPE_CONFIRM 20 /* command processed confirmation */ +#define CPC_MSG_TYPE_OVERRUN 21 /* overrun events */ +#define CPC_MSG_TYPE_CAN_FRAME_ERROR 23 /* detected bus errors */ +#define CPC_MSG_TYPE_ERR_COUNTER 25 /* RX/TX error counter */ + +/* Messages from the PC to the CPC interface */ +#define CPC_CMD_TYPE_CAN_FRAME 1 /* CAN data frame */ +#define CPC_CMD_TYPE_CONTROL 3 /* control of interface behavior */ +#define CPC_CMD_TYPE_CAN_PARAMS 6 /* set CAN parameters */ +#define CPC_CMD_TYPE_RTR_FRAME 13 /* CAN remote frame */ +#define CPC_CMD_TYPE_CAN_STATE 14 /* CAN state message */ +#define CPC_CMD_TYPE_EXT_CAN_FRAME 15 /* Extended CAN data frame */ +#define CPC_CMD_TYPE_EXT_RTR_FRAME 16 /* Extended CAN remote frame */ +#define CPC_CMD_TYPE_CAN_EXIT 200 /* exit the CAN */ + +#define CPC_CMD_TYPE_INQ_ERR_COUNTER 25 /* request the CAN error counters */ +#define CPC_CMD_TYPE_CLEAR_MSG_QUEUE 8 /* clear CPC_MSG queue */ +#define CPC_CMD_TYPE_CLEAR_CMD_QUEUE 28 /* clear CPC_CMD queue */ + +#define CPC_CC_TYPE_SJA1000 2 /* Philips basic CAN controller */ + +#define CPC_CAN_ECODE_ERRFRAME 0x01 /* Ecode type */ + +/* Overrun types */ +#define CPC_OVR_EVENT_CAN 0x01 +#define CPC_OVR_EVENT_CANSTATE 0x02 +#define CPC_OVR_EVENT_BUSERROR 0x04 + +/* + * If the CAN controller lost a message we indicate it with the highest bit + * set in the count field. + */ +#define CPC_OVR_HW 0x80 + +/* Size of the "struct ems_cpc_msg" without the union */ +#define CPC_MSG_HEADER_LEN 11 +#define CPC_CAN_MSG_MIN_SIZE 5 + +/* Define these values to match your devices */ +#define USB_CPCUSB_VENDOR_ID 0x12D6 + +#define USB_CPCUSB_ARM7_PRODUCT_ID 0x0444 + +/* Mode register NXP LPC2119/SJA1000 CAN Controller */ +#define SJA1000_MOD_NORMAL 0x00 +#define SJA1000_MOD_RM 0x01 + +/* ECC register NXP LPC2119/SJA1000 CAN Controller */ +#define SJA1000_ECC_SEG 0x1F +#define SJA1000_ECC_DIR 0x20 +#define SJA1000_ECC_ERR 0x06 +#define SJA1000_ECC_BIT 0x00 +#define SJA1000_ECC_FORM 0x40 +#define SJA1000_ECC_STUFF 0x80 +#define SJA1000_ECC_MASK 0xc0 + +/* Status register content */ +#define SJA1000_SR_BS 0x80 +#define SJA1000_SR_ES 0x40 + +#define SJA1000_DEFAULT_OUTPUT_CONTROL 0xDA + +/* + * The device actually uses a 16MHz clock to generate the CAN clock + * but it expects SJA1000 bit settings based on 8MHz (is internally + * converted). + */ +#define EMS_USB_ARM7_CLOCK 8000000 + +/* + * CAN-Message representation in a CPC_MSG. Message object type is + * CPC_MSG_TYPE_CAN_FRAME or CPC_MSG_TYPE_RTR_FRAME or + * CPC_MSG_TYPE_EXT_CAN_FRAME or CPC_MSG_TYPE_EXT_RTR_FRAME. + */ +struct cpc_can_msg { + u32 id; + u8 length; + u8 msg[8]; +}; + +/* Representation of the CAN parameters for the SJA1000 controller */ +struct cpc_sja1000_params { + u8 mode; + u8 acc_code0; + u8 acc_code1; + u8 acc_code2; + u8 acc_code3; + u8 acc_mask0; + u8 acc_mask1; + u8 acc_mask2; + u8 acc_mask3; + u8 btr0; + u8 btr1; + u8 outp_contr; +}; + +/* CAN params message representation */ +struct cpc_can_params { + u8 cc_type; + + /* Will support M16C CAN controller in the future */ + union { + struct cpc_sja1000_params sja1000; + } cc_params; +}; + +/* Structure for confirmed message handling */ +struct cpc_confirm { + u8 error; /* error code */ +}; + +/* Structure for overrun conditions */ +struct cpc_overrun { + u8 event; + u8 count; +}; + +/* SJA1000 CAN errors (compatible to NXP LPC2119) */ +struct cpc_sja1000_can_error { + u8 ecc; + u8 rxerr; + u8 txerr; +}; + +/* structure for CAN error conditions */ +struct cpc_can_error { + u8 ecode; + + struct { + u8 cc_type; + + /* Other controllers may also provide error code capture regs */ + union { + struct cpc_sja1000_can_error sja1000; + } regs; + } cc; +}; + +/* + * Structure containing RX/TX error counter. This structure is used to request + * the values of the CAN controllers TX and RX error counter. + */ +struct cpc_can_err_counter { + u8 rx; + u8 tx; +}; + +/* Main message type used between library and application */ +struct __attribute__ ((packed)) ems_cpc_msg { + u8 type; /* type of message */ + u8 length; /* length of data within union 'msg' */ + u8 msgid; /* confirmation handle */ + u32 ts_sec; /* timestamp in seconds */ + u32 ts_nsec; /* timestamp in nano seconds */ + + union { + u8 generic[64]; + struct cpc_can_msg can_msg; + struct cpc_can_params can_params; + struct cpc_confirm confirmation; + struct cpc_overrun overrun; + struct cpc_can_error error; + struct cpc_can_err_counter err_counter; + u8 can_state; + } msg; +}; + +/* + * Table of devices that work with this driver + * NOTE: This driver supports only CPC-USB/ARM7 (LPC2119) yet. + */ +static struct usb_device_id ems_usb_table[] = { + {USB_DEVICE(USB_CPCUSB_VENDOR_ID, USB_CPCUSB_ARM7_PRODUCT_ID)}, + {} /* Terminating entry */ +}; + +MODULE_DEVICE_TABLE(usb, ems_usb_table); + +#define RX_BUFFER_SIZE 64 +#define CPC_HEADER_SIZE 4 +#define INTR_IN_BUFFER_SIZE 4 + +#define MAX_RX_URBS 10 +#define MAX_TX_URBS CAN_ECHO_SKB_MAX + +struct ems_usb; + +struct ems_tx_urb_context { + struct ems_usb *dev; + + u32 echo_index; + u8 dlc; +}; + +struct ems_usb { + struct can_priv can; /* must be the first member */ + int open_time; + + struct sk_buff *echo_skb[MAX_TX_URBS]; + + struct usb_device *udev; + struct net_device *netdev; + + atomic_t active_tx_urbs; + struct usb_anchor tx_submitted; + struct ems_tx_urb_context tx_contexts[MAX_TX_URBS]; + + struct usb_anchor rx_submitted; + + struct urb *intr_urb; + + u8 *tx_msg_buffer; + + u8 *intr_in_buffer; + unsigned int free_slots; /* remember number of available slots */ + + struct ems_cpc_msg active_params; /* active controller parameters */ +}; + +static void ems_usb_read_interrupt_callback(struct urb *urb) +{ + struct ems_usb *dev = urb->context; + struct net_device *netdev = dev->netdev; + int err; + + if (!netif_device_present(netdev)) + return; + + switch (urb->status) { + case 0: + dev->free_slots = dev->intr_in_buffer[1]; + break; + + case -ECONNRESET: /* unlink */ + case -ENOENT: + case -ESHUTDOWN: + return; + + default: + dev_info(netdev->dev.parent, "Rx interrupt aborted %d\n", + urb->status); + break; + } + + err = usb_submit_urb(urb, GFP_ATOMIC); + + if (err == -ENODEV) + netif_device_detach(netdev); + else if (err) + dev_err(netdev->dev.parent, + "failed resubmitting intr urb: %d\n", err); + + return; +} + +static void ems_usb_rx_can_msg(struct ems_usb *dev, struct ems_cpc_msg *msg) +{ + struct can_frame *cf; + struct sk_buff *skb; + int i; + struct net_device_stats *stats = &dev->netdev->stats; + + skb = netdev_alloc_skb(dev->netdev, sizeof(struct can_frame)); + if (skb == NULL) + return; + + skb->protocol = htons(ETH_P_CAN); + + cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame)); + + cf->can_id = msg->msg.can_msg.id; + cf->can_dlc = min_t(u8, msg->msg.can_msg.length, 8); + + if (msg->type == CPC_MSG_TYPE_EXT_CAN_FRAME + || msg->type == CPC_MSG_TYPE_EXT_RTR_FRAME) + cf->can_id |= CAN_EFF_FLAG; + + if (msg->type == CPC_MSG_TYPE_RTR_FRAME + || msg->type == CPC_MSG_TYPE_EXT_RTR_FRAME) { + cf->can_id |= CAN_RTR_FLAG; + } else { + for (i = 0; i < cf->can_dlc; i++) + cf->data[i] = msg->msg.can_msg.msg[i]; + } + + netif_rx(skb); + + stats->rx_packets++; + stats->rx_bytes += cf->can_dlc; +} + +static void ems_usb_rx_err(struct ems_usb *dev, struct ems_cpc_msg *msg) +{ + struct can_frame *cf; + struct sk_buff *skb; + struct net_device_stats *stats = &dev->netdev->stats; + + skb = netdev_alloc_skb(dev->netdev, sizeof(struct can_frame)); + if (skb == NULL) + return; + + skb->protocol = htons(ETH_P_CAN); + + cf = (struct can_frame *)skb_put(skb, sizeof(struct can_frame)); + memset(cf, 0, sizeof(struct can_frame)); + + cf->can_id = CAN_ERR_FLAG; + cf->can_dlc = CAN_ERR_DLC; + + if (msg->type == CPC_MSG_TYPE_CAN_STATE) { + u8 state = msg->msg.can_state; + + if (state & SJA1000_SR_BS) { + dev->can.state = CAN_STATE_BUS_OFF; + cf->can_id |= CAN_ERR_BUSOFF; + + can_bus_off(dev->netdev); + } else if (state & SJA1000_SR_ES) { + dev->can.state = CAN_STATE_ERROR_WARNING; + dev->can.can_stats.error_warning++; + } else { + dev->can.state = CAN_STATE_ERROR_ACTIVE; + dev->can.can_stats.error_passive++; + } + } else if (msg->type == CPC_MSG_TYPE_CAN_FRAME_ERROR) { + u8 ecc = msg->msg.error.cc.regs.sja1000.ecc; + u8 txerr = msg->msg.error.cc.regs.sja1000.txerr; + u8 rxerr = msg->msg.error.cc.regs.sja1000.rxerr; + + /* bus error interrupt */ + dev->can.can_stats.bus_error++; + stats->rx_errors++; + + cf->can_id |= CAN_ERR_PROT | CAN_ERR_BUSERROR; + + switch (ecc & SJA1000_ECC_MASK) { + case SJA1000_ECC_BIT: + cf->data[2] |= CAN_ERR_PROT_BIT; + break; + case SJA1000_ECC_FORM: + cf->data[2] |= CAN_ERR_PROT_FORM; + break; + case SJA1000_ECC_STUFF: + cf->data[2] |= CAN_ERR_PROT_STUFF; + break; + default: + cf->data[2] |= CAN_ERR_PROT_UNSPEC; + cf->data[3] = ecc & SJA1000_ECC_SEG; + break; + } + + /* Error occured during transmission? */ + if ((ecc & SJA1000_ECC_DIR) == 0) + cf->data[2] |= CAN_ERR_PROT_TX; + + if (dev->can.state == CAN_STATE_ERROR_WARNING || + dev->can.state == CAN_STATE_ERROR_PASSIVE) { + cf->data[1] = (txerr > rxerr) ? + CAN_ERR_CRTL_TX_PASSIVE : CAN_ERR_CRTL_RX_PASSIVE; + } + } else if (msg->type == CPC_MSG_TYPE_OVERRUN) { + cf->can_id |= CAN_ERR_CRTL; + cf->data[1] = CAN_ERR_CRTL_RX_OVERFLOW; + + stats->rx_over_errors++; + stats->rx_errors++; + } + + netif_rx(skb); + + stats->rx_packets++; + stats->rx_bytes += cf->can_dlc; +} + +/* + * callback for bulk IN urb + */ +static void ems_usb_read_bulk_callback(struct urb *urb) +{ + struct ems_usb *dev = urb->context; + struct net_device *netdev; + int retval; + + netdev = dev->netdev; + + if (!netif_device_present(netdev)) + return; + + switch (urb->status) { + case 0: /* success */ + break; + + case -ENOENT: + return; + + default: + dev_info(netdev->dev.parent, "Rx URB aborted (%d)\n", + urb->status); + goto resubmit_urb; + } + + if (urb->actual_length > CPC_HEADER_SIZE) { + struct ems_cpc_msg *msg; + u8 *ibuf = urb->transfer_buffer; + u8 msg_count, again, start; + + msg_count = ibuf[0] & ~0x80; + again = ibuf[0] & 0x80; + + start = CPC_HEADER_SIZE; + + while (msg_count) { + msg = (struct ems_cpc_msg *)&ibuf[start]; + + switch (msg->type) { + case CPC_MSG_TYPE_CAN_STATE: + /* Process CAN state changes */ + ems_usb_rx_err(dev, msg); + break; + + case CPC_MSG_TYPE_CAN_FRAME: + case CPC_MSG_TYPE_EXT_CAN_FRAME: + case CPC_MSG_TYPE_RTR_FRAME: + case CPC_MSG_TYPE_EXT_RTR_FRAME: + ems_usb_rx_can_msg(dev, msg); + break; + + case CPC_MSG_TYPE_CAN_FRAME_ERROR: + /* Process errorframe */ + ems_usb_rx_err(dev, msg); + break; + + case CPC_MSG_TYPE_OVERRUN: + /* Message lost while receiving */ + ems_usb_rx_err(dev, msg); + break; + } + + start += CPC_MSG_HEADER_LEN + msg->length; + msg_count--; + + if (start > urb->transfer_buffer_length) { + dev_err(netdev->dev.parent, "format error\n"); + break; + } + } + } + +resubmit_urb: + usb_fill_bulk_urb(urb, dev->udev, usb_rcvbulkpipe(dev->udev, 2), + urb->transfer_buffer, RX_BUFFER_SIZE, + ems_usb_read_bulk_callback, dev); + + retval = usb_submit_urb(urb, GFP_ATOMIC); + + if (retval == -ENODEV) + netif_device_detach(netdev); + else if (retval) + dev_err(netdev->dev.parent, + "failed resubmitting read bulk urb: %d\n", retval); + + return; +} + +/* + * callback for bulk IN urb + */ +static void ems_usb_write_bulk_callback(struct urb *urb) +{ + struct ems_tx_urb_context *context = urb->context; + struct ems_usb *dev; + struct net_device *netdev; + + BUG_ON(!context); + + dev = context->dev; + netdev = dev->netdev; + + /* free up our allocated buffer */ + usb_buffer_free(urb->dev, urb->transfer_buffer_length, + urb->transfer_buffer, urb->transfer_dma); + + atomic_dec(&dev->active_tx_urbs); + + if (!netif_device_present(netdev)) + return; + + if (urb->status) + dev_info(netdev->dev.parent, "Tx URB aborted (%d)\n", + urb->status); + + netdev->trans_start = jiffies; + + /* transmission complete interrupt */ + netdev->stats.tx_packets++; + netdev->stats.tx_bytes += context->dlc; + + can_get_echo_skb(netdev, context->echo_index); + + /* Release context */ + context->echo_index = MAX_TX_URBS; + + if (netif_queue_stopped(netdev)) + netif_wake_queue(netdev); +} + +/* + * Send the given CPC command synchronously + */ +static int ems_usb_command_msg(struct ems_usb *dev, struct ems_cpc_msg *msg) +{ + int actual_length; + + /* Copy payload */ + memcpy(&dev->tx_msg_buffer[CPC_HEADER_SIZE], msg, + msg->length + CPC_MSG_HEADER_LEN); + + /* Clear header */ + memset(&dev->tx_msg_buffer[0], 0, CPC_HEADER_SIZE); + + return usb_bulk_msg(dev->udev, usb_sndbulkpipe(dev->udev, 2), + &dev->tx_msg_buffer[0], + msg->length + CPC_MSG_HEADER_LEN + CPC_HEADER_SIZE, + &actual_length, 1000); +} + +/* + * Change CAN controllers' mode register + */ +static int ems_usb_write_mode(struct ems_usb *dev, u8 mode) +{ + dev->active_params.msg.can_params.cc_params.sja1000.mode = mode; + + return ems_usb_command_msg(dev, &dev->active_params); +} + +/* + * Send a CPC_Control command to change behaviour when interface receives a CAN + * message, bus error or CAN state changed notifications. + */ +static int ems_usb_control_cmd(struct ems_usb *dev, u8 val) +{ + struct ems_cpc_msg cmd; + + cmd.type = CPC_CMD_TYPE_CONTROL; + cmd.length = CPC_MSG_HEADER_LEN + 1; + + cmd.msgid = 0; + + cmd.msg.generic[0] = val; + + return ems_usb_command_msg(dev, &cmd); +} + +/* + * Start interface + */ +static int ems_usb_start(struct ems_usb *dev) +{ + struct net_device *netdev = dev->netdev; + int err, i; + + dev->intr_in_buffer[0] = 0; + dev->free_slots = 15; /* initial size */ + + for (i = 0; i < MAX_RX_URBS; i++) { + struct urb *urb = NULL; + u8 *buf = NULL; + + /* create a URB, and a buffer for it */ + urb = usb_alloc_urb(0, GFP_KERNEL); + if (!urb) { + dev_err(netdev->dev.parent, + "No memory left for URBs\n"); + return -ENOMEM; + } + + buf = usb_buffer_alloc(dev->udev, RX_BUFFER_SIZE, GFP_KERNEL, + &urb->transfer_dma); + if (!buf) { + dev_err(netdev->dev.parent, + "No memory left for USB buffer\n"); + usb_free_urb(urb); + return -ENOMEM; + } + + usb_fill_bulk_urb(urb, dev->udev, usb_rcvbulkpipe(dev->udev, 2), + buf, RX_BUFFER_SIZE, + ems_usb_read_bulk_callback, dev); + urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + usb_anchor_urb(urb, &dev->rx_submitted); + + err = usb_submit_urb(urb, GFP_KERNEL); + if (err) { + if (err == -ENODEV) + netif_device_detach(dev->netdev); + + usb_unanchor_urb(urb); + usb_buffer_free(dev->udev, RX_BUFFER_SIZE, buf, + urb->transfer_dma); + break; + } + + /* Drop reference, USB core will take care of freeing it */ + usb_free_urb(urb); + } + + /* Did we submit any URBs */ + if (i == 0) { + dev_warn(netdev->dev.parent, "couldn't setup read URBs\n"); + return err; + } + + /* Warn if we've couldn't transmit all the URBs */ + if (i < MAX_RX_URBS) + dev_warn(netdev->dev.parent, "rx performance may be slow\n"); + + /* Setup and start interrupt URB */ + usb_fill_int_urb(dev->intr_urb, dev->udev, + usb_rcvintpipe(dev->udev, 1), + dev->intr_in_buffer, + INTR_IN_BUFFER_SIZE, + ems_usb_read_interrupt_callback, dev, 1); + + err = usb_submit_urb(dev->intr_urb, GFP_KERNEL); + if (err) { + if (err == -ENODEV) + netif_device_detach(dev->netdev); + + dev_warn(netdev->dev.parent, "intr URB submit failed: %d\n", + err); + + return err; + } + + /* CPC-USB will transfer received message to host */ + err = ems_usb_control_cmd(dev, CONTR_CAN_MESSAGE | CONTR_CONT_ON); + if (err) + goto failed; + + /* CPC-USB will transfer CAN state changes to host */ + err = ems_usb_control_cmd(dev, CONTR_CAN_STATE | CONTR_CONT_ON); + if (err) + goto failed; + + /* CPC-USB will transfer bus errors to host */ + err = ems_usb_control_cmd(dev, CONTR_BUS_ERROR | CONTR_CONT_ON); + if (err) + goto failed; + + err = ems_usb_write_mode(dev, SJA1000_MOD_NORMAL); + if (err) + goto failed; + + dev->can.state = CAN_STATE_ERROR_ACTIVE; + + return 0; + +failed: + if (err == -ENODEV) + netif_device_detach(dev->netdev); + + dev_warn(netdev->dev.parent, "couldn't submit control: %d\n", err); + + return err; +} + +static void unlink_all_urbs(struct ems_usb *dev) +{ + int i; + + usb_unlink_urb(dev->intr_urb); + + usb_kill_anchored_urbs(&dev->rx_submitted); + + usb_kill_anchored_urbs(&dev->tx_submitted); + atomic_set(&dev->active_tx_urbs, 0); + + for (i = 0; i < MAX_TX_URBS; i++) + dev->tx_contexts[i].echo_index = MAX_TX_URBS; +} + +static int ems_usb_open(struct net_device *netdev) +{ + struct ems_usb *dev = netdev_priv(netdev); + int err; + + err = ems_usb_write_mode(dev, SJA1000_MOD_RM); + if (err) + return err; + + /* common open */ + err = open_candev(netdev); + if (err) + return err; + + /* finally start device */ + err = ems_usb_start(dev); + if (err) { + if (err == -ENODEV) + netif_device_detach(dev->netdev); + + dev_warn(netdev->dev.parent, "couldn't start device: %d\n", + err); + + close_candev(netdev); + + return err; + } + + dev->open_time = jiffies; + + netif_start_queue(netdev); + + return 0; +} + +static netdev_tx_t ems_usb_start_xmit(struct sk_buff *skb, struct net_device *netdev) +{ + struct ems_usb *dev = netdev_priv(netdev); + struct ems_tx_urb_context *context = NULL; + struct net_device_stats *stats = &netdev->stats; + struct can_frame *cf = (struct can_frame *)skb->data; + struct ems_cpc_msg *msg; + struct urb *urb; + u8 *buf; + int i, err; + size_t size = CPC_HEADER_SIZE + CPC_MSG_HEADER_LEN + + sizeof(struct cpc_can_msg); + + /* create a URB, and a buffer for it, and copy the data to the URB */ + urb = usb_alloc_urb(0, GFP_ATOMIC); + if (!urb) { + dev_err(netdev->dev.parent, "No memory left for URBs\n"); + goto nomem; + } + + buf = usb_buffer_alloc(dev->udev, size, GFP_ATOMIC, &urb->transfer_dma); + if (!buf) { + dev_err(netdev->dev.parent, "No memory left for USB buffer\n"); + usb_free_urb(urb); + goto nomem; + } + + msg = (struct ems_cpc_msg *)&buf[CPC_HEADER_SIZE]; + + msg->msg.can_msg.id = cf->can_id & CAN_ERR_MASK; + msg->msg.can_msg.length = cf->can_dlc; + + if (cf->can_id & CAN_RTR_FLAG) { + msg->type = cf->can_id & CAN_EFF_FLAG ? + CPC_CMD_TYPE_EXT_RTR_FRAME : CPC_CMD_TYPE_RTR_FRAME; + + msg->length = CPC_CAN_MSG_MIN_SIZE; + } else { + msg->type = cf->can_id & CAN_EFF_FLAG ? + CPC_CMD_TYPE_EXT_CAN_FRAME : CPC_CMD_TYPE_CAN_FRAME; + + for (i = 0; i < cf->can_dlc; i++) + msg->msg.can_msg.msg[i] = cf->data[i]; + + msg->length = CPC_CAN_MSG_MIN_SIZE + cf->can_dlc; + } + + for (i = 0; i < MAX_TX_URBS; i++) { + if (dev->tx_contexts[i].echo_index == MAX_TX_URBS) { + context = &dev->tx_contexts[i]; + break; + } + } + + /* + * May never happen! When this happens we'd more URBs in flight as + * allowed (MAX_TX_URBS). + */ + if (!context) { + usb_unanchor_urb(urb); + usb_buffer_free(dev->udev, size, buf, urb->transfer_dma); + + dev_warn(netdev->dev.parent, "couldn't find free context\n"); + + return NETDEV_TX_BUSY; + } + + context->dev = dev; + context->echo_index = i; + context->dlc = cf->can_dlc; + + usb_fill_bulk_urb(urb, dev->udev, usb_sndbulkpipe(dev->udev, 2), buf, + size, ems_usb_write_bulk_callback, context); + urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP; + usb_anchor_urb(urb, &dev->tx_submitted); + + can_put_echo_skb(skb, netdev, context->echo_index); + + atomic_inc(&dev->active_tx_urbs); + + err = usb_submit_urb(urb, GFP_ATOMIC); + if (unlikely(err)) { + can_free_echo_skb(netdev, context->echo_index); + + usb_unanchor_urb(urb); + usb_buffer_free(dev->udev, size, buf, urb->transfer_dma); + dev_kfree_skb(skb); + + atomic_dec(&dev->active_tx_urbs); + + if (err == -ENODEV) { + netif_device_detach(netdev); + } else { + dev_warn(netdev->dev.parent, "failed tx_urb %d\n", err); + + stats->tx_dropped++; + } + } else { + netdev->trans_start = jiffies; + + /* Slow down tx path */ + if (atomic_read(&dev->active_tx_urbs) >= MAX_TX_URBS || + dev->free_slots < 5) { + netif_stop_queue(netdev); + } + } + + /* + * Release our reference to this URB, the USB core will eventually free + * it entirely. + */ + usb_free_urb(urb); + + return NETDEV_TX_OK; + +nomem: + if (skb) + dev_kfree_skb(skb); + + stats->tx_dropped++; + + return NETDEV_TX_OK; +} + +static int ems_usb_close(struct net_device *netdev) +{ + struct ems_usb *dev = netdev_priv(netdev); + + /* Stop polling */ + unlink_all_urbs(dev); + + netif_stop_queue(netdev); + + /* Set CAN controller to reset mode */ + if (ems_usb_write_mode(dev, SJA1000_MOD_RM)) + dev_warn(netdev->dev.parent, "couldn't stop device"); + + close_candev(netdev); + + dev->open_time = 0; + + return 0; +} + +static const struct net_device_ops ems_usb_netdev_ops = { + .ndo_open = ems_usb_open, + .ndo_stop = ems_usb_close, + .ndo_start_xmit = ems_usb_start_xmit, +}; + +static struct can_bittiming_const ems_usb_bittiming_const = { + .name = "ems_usb", + .tseg1_min = 1, + .tseg1_max = 16, + .tseg2_min = 1, + .tseg2_max = 8, + .sjw_max = 4, + .brp_min = 1, + .brp_max = 64, + .brp_inc = 1, +}; + +static int ems_usb_set_mode(struct net_device *netdev, enum can_mode mode) +{ + struct ems_usb *dev = netdev_priv(netdev); + + if (!dev->open_time) + return -EINVAL; + + switch (mode) { + case CAN_MODE_START: + if (ems_usb_write_mode(dev, SJA1000_MOD_NORMAL)) + dev_warn(netdev->dev.parent, "couldn't start device"); + + if (netif_queue_stopped(netdev)) + netif_wake_queue(netdev); + break; + + default: + return -EOPNOTSUPP; + } + + return 0; +} + +static int ems_usb_set_bittiming(struct net_device *netdev) +{ + struct ems_usb *dev = netdev_priv(netdev); + struct can_bittiming *bt = &dev->can.bittiming; + u8 btr0, btr1; + + btr0 = ((bt->brp - 1) & 0x3f) | (((bt->sjw - 1) & 0x3) << 6); + btr1 = ((bt->prop_seg + bt->phase_seg1 - 1) & 0xf) | + (((bt->phase_seg2 - 1) & 0x7) << 4); + if (dev->can.ctrlmode & CAN_CTRLMODE_3_SAMPLES) + btr1 |= 0x80; + + dev_info(netdev->dev.parent, "setting BTR0=0x%02x BTR1=0x%02x\n", + btr0, btr1); + + dev->active_params.msg.can_params.cc_params.sja1000.btr0 = btr0; + dev->active_params.msg.can_params.cc_params.sja1000.btr1 = btr1; + + return ems_usb_command_msg(dev, &dev->active_params); +} + +static void init_params_sja1000(struct ems_cpc_msg *msg) +{ + struct cpc_sja1000_params *sja1000 = + &msg->msg.can_params.cc_params.sja1000; + + msg->type = CPC_CMD_TYPE_CAN_PARAMS; + msg->length = sizeof(struct cpc_can_params); + msg->msgid = 0; + + msg->msg.can_params.cc_type = CPC_CC_TYPE_SJA1000; + + /* Acceptance filter open */ + sja1000->acc_code0 = 0x00; + sja1000->acc_code1 = 0x00; + sja1000->acc_code2 = 0x00; + sja1000->acc_code3 = 0x00; + + /* Acceptance filter open */ + sja1000->acc_mask0 = 0xFF; + sja1000->acc_mask1 = 0xFF; + sja1000->acc_mask2 = 0xFF; + sja1000->acc_mask3 = 0xFF; + + sja1000->btr0 = 0; + sja1000->btr1 = 0; + + sja1000->outp_contr = SJA1000_DEFAULT_OUTPUT_CONTROL; + sja1000->mode = SJA1000_MOD_RM; +} + +/* + * probe function for new CPC-USB devices + */ +static int ems_usb_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + struct net_device *netdev; + struct ems_usb *dev; + int i, err = -ENOMEM; + + netdev = alloc_candev(sizeof(struct ems_usb)); + if (!netdev) { + dev_err(netdev->dev.parent, "Couldn't alloc candev\n"); + return -ENOMEM; + } + + dev = netdev_priv(netdev); + + dev->udev = interface_to_usbdev(intf); + dev->netdev = netdev; + + dev->can.state = CAN_STATE_STOPPED; + dev->can.clock.freq = EMS_USB_ARM7_CLOCK; + dev->can.bittiming_const = &ems_usb_bittiming_const; + dev->can.do_set_bittiming = ems_usb_set_bittiming; + dev->can.do_set_mode = ems_usb_set_mode; + + netdev->flags |= IFF_ECHO; /* we support local echo */ + + netdev->netdev_ops = &ems_usb_netdev_ops; + + netdev->flags |= IFF_ECHO; /* we support local echo */ + + init_usb_anchor(&dev->rx_submitted); + + init_usb_anchor(&dev->tx_submitted); + atomic_set(&dev->active_tx_urbs, 0); + + for (i = 0; i < MAX_TX_URBS; i++) + dev->tx_contexts[i].echo_index = MAX_TX_URBS; + + dev->intr_urb = usb_alloc_urb(0, GFP_KERNEL); + if (!dev->intr_urb) { + dev_err(netdev->dev.parent, "Couldn't alloc intr URB\n"); + goto cleanup_candev; + } + + dev->intr_in_buffer = kzalloc(INTR_IN_BUFFER_SIZE, GFP_KERNEL); + if (!dev->intr_in_buffer) { + dev_err(netdev->dev.parent, "Couldn't alloc Intr buffer\n"); + goto cleanup_intr_urb; + } + + dev->tx_msg_buffer = kzalloc(CPC_HEADER_SIZE + + sizeof(struct ems_cpc_msg), GFP_KERNEL); + if (!dev->tx_msg_buffer) { + dev_err(netdev->dev.parent, "Couldn't alloc Tx buffer\n"); + goto cleanup_intr_in_buffer; + } + + usb_set_intfdata(intf, dev); + + SET_NETDEV_DEV(netdev, &intf->dev); + + init_params_sja1000(&dev->active_params); + + err = ems_usb_command_msg(dev, &dev->active_params); + if (err) { + dev_err(netdev->dev.parent, + "couldn't initialize controller: %d\n", err); + goto cleanup_tx_msg_buffer; + } + + err = register_candev(netdev); + if (err) { + dev_err(netdev->dev.parent, + "couldn't register CAN device: %d\n", err); + goto cleanup_tx_msg_buffer; + } + + return 0; + +cleanup_tx_msg_buffer: + kfree(dev->tx_msg_buffer); + +cleanup_intr_in_buffer: + kfree(dev->intr_in_buffer); + +cleanup_intr_urb: + usb_free_urb(dev->intr_urb); + +cleanup_candev: + free_candev(netdev); + + return err; +} + +/* + * called by the usb core when the device is removed from the system + */ +static void ems_usb_disconnect(struct usb_interface *intf) +{ + struct ems_usb *dev = usb_get_intfdata(intf); + + usb_set_intfdata(intf, NULL); + + if (dev) { + unregister_netdev(dev->netdev); + free_candev(dev->netdev); + + unlink_all_urbs(dev); + + usb_free_urb(dev->intr_urb); + + kfree(dev->intr_in_buffer); + } +} + +/* usb specific object needed to register this driver with the usb subsystem */ +static struct usb_driver ems_usb_driver = { + .name = "ems_usb", + .probe = ems_usb_probe, + .disconnect = ems_usb_disconnect, + .id_table = ems_usb_table, +}; + +static int __init ems_usb_init(void) +{ + int err; + + printk(KERN_INFO "CPC-USB kernel driver loaded\n"); + + /* register this driver with the USB subsystem */ + err = usb_register(&ems_usb_driver); + + if (err) { + err("usb_register failed. Error number %d\n", err); + return err; + } + + return 0; +} + +static void __exit ems_usb_exit(void) +{ + /* deregister this driver with the USB subsystem */ + usb_deregister(&ems_usb_driver); +} + +module_init(ems_usb_init); +module_exit(ems_usb_exit); diff --git a/drivers/net/can/vcan.c b/drivers/net/can/vcan.c index 6971f6cd37f..80ac5631398 100644 --- a/drivers/net/can/vcan.c +++ b/drivers/net/can/vcan.c @@ -80,7 +80,7 @@ static void vcan_rx(struct sk_buff *skb, struct net_device *dev) skb->dev = dev; skb->ip_summed = CHECKSUM_UNNECESSARY; - netif_rx(skb); + netif_rx_ni(skb); } static netdev_tx_t vcan_tx(struct sk_buff *skb, struct net_device *dev) diff --git a/drivers/net/cnic.c b/drivers/net/cnic.c index d45eacb7670..211c8e9182f 100644 --- a/drivers/net/cnic.c +++ b/drivers/net/cnic.c @@ -85,8 +85,6 @@ static int cnic_uio_open(struct uio_info *uinfo, struct inode *inode) cp->uio_dev = iminor(inode); - cnic_shutdown_bnx2_rx_ring(dev); - cnic_init_bnx2_tx_ring(dev); cnic_init_bnx2_rx_ring(dev); @@ -98,6 +96,8 @@ static int cnic_uio_close(struct uio_info *uinfo, struct inode *inode) struct cnic_dev *dev = uinfo->priv; struct cnic_local *cp = dev->cnic_priv; + cnic_shutdown_bnx2_rx_ring(dev); + cp->uio_dev = -1; return 0; } diff --git a/drivers/net/cpmac.c b/drivers/net/cpmac.c index 3e3fab8afb1..61f9da2b494 100644 --- a/drivers/net/cpmac.c +++ b/drivers/net/cpmac.c @@ -1109,7 +1109,7 @@ static int external_switch; static int __devinit cpmac_probe(struct platform_device *pdev) { int rc, phy_id; - char mdio_bus_id[BUS_ID_SIZE]; + char mdio_bus_id[MII_BUS_ID_SIZE]; struct resource *mem; struct cpmac_priv *priv; struct net_device *dev; @@ -1118,7 +1118,7 @@ static int __devinit cpmac_probe(struct platform_device *pdev) pdata = pdev->dev.platform_data; if (external_switch || dumb_switch) { - strncpy(mdio_bus_id, "0", BUS_ID_SIZE); /* fixed phys bus */ + strncpy(mdio_bus_id, "0", MII_BUS_ID_SIZE); /* fixed phys bus */ phy_id = pdev->id; } else { for (phy_id = 0; phy_id < PHY_MAX_ADDR; phy_id++) { @@ -1126,7 +1126,7 @@ static int __devinit cpmac_probe(struct platform_device *pdev) continue; if (!cpmac_mii->phy_map[phy_id]) continue; - strncpy(mdio_bus_id, cpmac_mii->id, BUS_ID_SIZE); + strncpy(mdio_bus_id, cpmac_mii->id, MII_BUS_ID_SIZE); break; } } @@ -1167,7 +1167,7 @@ static int __devinit cpmac_probe(struct platform_device *pdev) priv->msg_enable = netif_msg_init(debug_level, 0xff); memcpy(dev->dev_addr, pdata->dev_addr, sizeof(dev->dev_addr)); - snprintf(priv->phy_name, BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id); + snprintf(priv->phy_name, MII_BUS_ID_SIZE, PHY_ID_FMT, mdio_bus_id, phy_id); priv->phy = phy_connect(dev, priv->phy_name, &cpmac_adjust_link, 0, PHY_INTERFACE_MODE_MII); diff --git a/drivers/net/cris/eth_v10.c b/drivers/net/cris/eth_v10.c index 15c0195ebd3..a24be34a3f7 100644 --- a/drivers/net/cris/eth_v10.c +++ b/drivers/net/cris/eth_v10.c @@ -768,10 +768,24 @@ e100_negotiate(struct net_device* dev) e100_set_mdio_reg(dev, np->mii_if.phy_id, MII_ADVERTISE, data); - /* Renegotiate with link partner */ + data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR); if (autoneg_normal) { - data = e100_get_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR); - data |= BMCR_ANENABLE | BMCR_ANRESTART; + /* Renegotiate with link partner */ + data |= BMCR_ANENABLE | BMCR_ANRESTART; + } else { + /* Don't negotiate speed or duplex */ + data &= ~(BMCR_ANENABLE | BMCR_ANRESTART); + + /* Set speed and duplex static */ + if (current_speed_selection == 10) + data &= ~BMCR_SPEED100; + else + data |= BMCR_SPEED100; + + if (current_duplex != full) + data &= ~BMCR_FULLDPLX; + else + data |= BMCR_FULLDPLX; } e100_set_mdio_reg(dev, np->mii_if.phy_id, MII_BMCR, data); } diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c index d465eaa796c..65a2d0ba64e 100644 --- a/drivers/net/davinci_emac.c +++ b/drivers/net/davinci_emac.c @@ -200,6 +200,9 @@ static const char emac_version_string[] = "TI DaVinci EMAC Linux v6.1"; /** NOTE:: For DM646x the IN_VECTOR has changed */ #define EMAC_DM646X_MAC_IN_VECTOR_RX_INT_VEC BIT(EMAC_DEF_RX_CH) #define EMAC_DM646X_MAC_IN_VECTOR_TX_INT_VEC BIT(16 + EMAC_DEF_TX_CH) +#define EMAC_DM646X_MAC_IN_VECTOR_HOST_INT BIT(26) +#define EMAC_DM646X_MAC_IN_VECTOR_STATPEND_INT BIT(27) + /* CPPI bit positions */ #define EMAC_CPPI_SOP_BIT BIT(31) @@ -2167,7 +2170,11 @@ static int emac_poll(struct napi_struct *napi, int budget) emac_int_enable(priv); } - if (unlikely(status & EMAC_DM644X_MAC_IN_VECTOR_HOST_INT)) { + mask = EMAC_DM644X_MAC_IN_VECTOR_HOST_INT; + if (priv->version == EMAC_VERSION_2) + mask = EMAC_DM646X_MAC_IN_VECTOR_HOST_INT; + + if (unlikely(status & mask)) { u32 ch, cause; dev_err(emac_dev, "DaVinci EMAC: Fatal Hardware Error\n"); netif_stop_queue(ndev); diff --git a/drivers/net/e1000/e1000.h b/drivers/net/e1000/e1000.h index 1a4f89c66a2..42e2b7e21c2 100644 --- a/drivers/net/e1000/e1000.h +++ b/drivers/net/e1000/e1000.h @@ -149,7 +149,6 @@ do { \ #define AUTO_ALL_MODES 0 #define E1000_EEPROM_82544_APM 0x0004 -#define E1000_EEPROM_ICH8_APME 0x0004 #define E1000_EEPROM_APME 0x0400 #ifndef E1000_MASTER_SLAVE @@ -293,7 +292,6 @@ struct e1000_adapter { u64 hw_csum_err; u64 hw_csum_good; - u64 rx_hdr_split; u32 alloc_rx_buff_failed; u32 rx_int_delay; u32 rx_abs_int_delay; @@ -317,7 +315,6 @@ struct e1000_adapter { struct e1000_rx_ring test_rx_ring; int msg_enable; - bool have_msi; /* to not mess up cache alignment, always add to the bottom */ bool tso_force; diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c index 27f996a2010..490b2b7cd3a 100644 --- a/drivers/net/e1000/e1000_ethtool.c +++ b/drivers/net/e1000/e1000_ethtool.c @@ -82,7 +82,6 @@ static const struct e1000_stats e1000_gstrings_stats[] = { { "rx_long_byte_count", E1000_STAT(stats.gorcl) }, { "rx_csum_offload_good", E1000_STAT(hw_csum_good) }, { "rx_csum_offload_errors", E1000_STAT(hw_csum_err) }, - { "rx_header_split", E1000_STAT(rx_hdr_split) }, { "alloc_rx_buff_failed", E1000_STAT(alloc_rx_buff_failed) }, { "tx_smbus", E1000_STAT(stats.mgptc) }, { "rx_smbus", E1000_STAT(stats.mgprc) }, @@ -114,8 +113,6 @@ static int e1000_get_settings(struct net_device *netdev, SUPPORTED_1000baseT_Full| SUPPORTED_Autoneg | SUPPORTED_TP); - if (hw->phy_type == e1000_phy_ife) - ecmd->supported &= ~SUPPORTED_1000baseT_Full; ecmd->advertising = ADVERTISED_TP; if (hw->autoneg == 1) { @@ -178,14 +175,6 @@ static int e1000_set_settings(struct net_device *netdev, struct e1000_adapter *adapter = netdev_priv(netdev); struct e1000_hw *hw = &adapter->hw; - /* When SoL/IDER sessions are active, autoneg/speed/duplex - * cannot be changed */ - if (e1000_check_phy_reset_block(hw)) { - DPRINTK(DRV, ERR, "Cannot change link characteristics " - "when SoL/IDER is active.\n"); - return -EINVAL; - } - while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) msleep(1); @@ -330,10 +319,7 @@ static int e1000_set_tso(struct net_device *netdev, u32 data) else netdev->features &= ~NETIF_F_TSO; - if (data && (adapter->hw.mac_type > e1000_82547_rev_2)) - netdev->features |= NETIF_F_TSO6; - else - netdev->features &= ~NETIF_F_TSO6; + netdev->features &= ~NETIF_F_TSO6; DPRINTK(PROBE, INFO, "TSO is %s\n", data ? "Enabled" : "Disabled"); adapter->tso_force = true; @@ -441,7 +427,6 @@ static void e1000_get_regs(struct net_device *netdev, struct ethtool_regs *regs, regs_buff[24] = (u32)phy_data; /* phy local receiver status */ regs_buff[25] = regs_buff[24]; /* phy remote receiver status */ if (hw->mac_type >= e1000_82540 && - hw->mac_type < e1000_82571 && hw->media_type == e1000_media_type_copper) { regs_buff[26] = er32(MANC); } @@ -554,10 +539,8 @@ static int e1000_set_eeprom(struct net_device *netdev, ret_val = e1000_write_eeprom(hw, first_word, last_word - first_word + 1, eeprom_buff); - /* Update the checksum over the first part of the EEPROM if needed - * and flush shadow RAM for 82573 conrollers */ - if ((ret_val == 0) && ((first_word <= EEPROM_CHECKSUM_REG) || - (hw->mac_type == e1000_82573))) + /* Update the checksum over the first part of the EEPROM if needed */ + if ((ret_val == 0) && (first_word <= EEPROM_CHECKSUM_REG)) e1000_update_eeprom_checksum(hw); kfree(eeprom_buff); @@ -568,31 +551,12 @@ static void e1000_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *drvinfo) { struct e1000_adapter *adapter = netdev_priv(netdev); - struct e1000_hw *hw = &adapter->hw; char firmware_version[32]; - u16 eeprom_data; strncpy(drvinfo->driver, e1000_driver_name, 32); strncpy(drvinfo->version, e1000_driver_version, 32); - /* EEPROM image version # is reported as firmware version # for - * 8257{1|2|3} controllers */ - e1000_read_eeprom(hw, 5, 1, &eeprom_data); - switch (hw->mac_type) { - case e1000_82571: - case e1000_82572: - case e1000_82573: - case e1000_80003es2lan: - case e1000_ich8lan: - sprintf(firmware_version, "%d.%d-%d", - (eeprom_data & 0xF000) >> 12, - (eeprom_data & 0x0FF0) >> 4, - eeprom_data & 0x000F); - break; - default: - sprintf(firmware_version, "N/A"); - } - + sprintf(firmware_version, "N/A"); strncpy(drvinfo->fw_version, firmware_version, 32); strncpy(drvinfo->bus_info, pci_name(adapter->pdev), 32); drvinfo->regdump_len = e1000_get_regs_len(netdev); @@ -781,21 +745,9 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data) /* The status register is Read Only, so a write should fail. * Some bits that get toggled are ignored. */ - switch (hw->mac_type) { + /* there are several bits on newer hardware that are r/w */ - case e1000_82571: - case e1000_82572: - case e1000_80003es2lan: - toggle = 0x7FFFF3FF; - break; - case e1000_82573: - case e1000_ich8lan: - toggle = 0x7FFFF033; - break; - default: - toggle = 0xFFFFF833; - break; - } + toggle = 0xFFFFF833; before = er32(STATUS); value = (er32(STATUS) & toggle); @@ -810,12 +762,10 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data) /* restore previous status */ ew32(STATUS, before); - if (hw->mac_type != e1000_ich8lan) { - REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF); - REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF); - REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF); - REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF); - } + REG_PATTERN_TEST(FCAL, 0xFFFFFFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCAH, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(FCT, 0x0000FFFF, 0xFFFFFFFF); + REG_PATTERN_TEST(VET, 0x0000FFFF, 0xFFFFFFFF); REG_PATTERN_TEST(RDTR, 0x0000FFFF, 0xFFFFFFFF); REG_PATTERN_TEST(RDBAH, 0xFFFFFFFF, 0xFFFFFFFF); @@ -830,8 +780,7 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data) REG_SET_AND_CHECK(RCTL, 0xFFFFFFFF, 0x00000000); - before = (hw->mac_type == e1000_ich8lan ? - 0x06C3B33E : 0x06DFB3FE); + before = 0x06DFB3FE; REG_SET_AND_CHECK(RCTL, before, 0x003FFFFB); REG_SET_AND_CHECK(TCTL, 0xFFFFFFFF, 0x00000000); @@ -839,12 +788,10 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data) REG_SET_AND_CHECK(RCTL, before, 0xFFFFFFFF); REG_PATTERN_TEST(RDBAL, 0xFFFFFFF0, 0xFFFFFFFF); - if (hw->mac_type != e1000_ich8lan) - REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF); + REG_PATTERN_TEST(TXCW, 0xC000FFFF, 0x0000FFFF); REG_PATTERN_TEST(TDBAL, 0xFFFFFFF0, 0xFFFFFFFF); REG_PATTERN_TEST(TIDV, 0x0000FFFF, 0x0000FFFF); - value = (hw->mac_type == e1000_ich8lan ? - E1000_RAR_ENTRIES_ICH8LAN : E1000_RAR_ENTRIES); + value = E1000_RAR_ENTRIES; for (i = 0; i < value; i++) { REG_PATTERN_TEST(RA + (((i << 1) + 1) << 2), 0x8003FFFF, 0xFFFFFFFF); @@ -859,8 +806,7 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data) } - value = (hw->mac_type == e1000_ich8lan ? - E1000_MC_TBL_SIZE_ICH8LAN : E1000_MC_TBL_SIZE); + value = E1000_MC_TBL_SIZE; for (i = 0; i < value; i++) REG_PATTERN_TEST(MTA + (i << 2), 0xFFFFFFFF, 0xFFFFFFFF); @@ -933,9 +879,6 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data) /* Test each interrupt */ for (; i < 10; i++) { - if (hw->mac_type == e1000_ich8lan && i == 8) - continue; - /* Interrupt to test */ mask = 1 << i; @@ -1289,35 +1232,20 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter) e1000_write_phy_reg(hw, PHY_CTRL, 0x9140); /* autoneg off */ e1000_write_phy_reg(hw, PHY_CTRL, 0x8140); - } else if (hw->phy_type == e1000_phy_gg82563) - e1000_write_phy_reg(hw, - GG82563_PHY_KMRN_MODE_CTRL, - 0x1CC); + } ctrl_reg = er32(CTRL); - if (hw->phy_type == e1000_phy_ife) { - /* force 100, set loopback */ - e1000_write_phy_reg(hw, PHY_CTRL, 0x6100); + /* force 1000, set loopback */ + e1000_write_phy_reg(hw, PHY_CTRL, 0x4140); - /* Now set up the MAC to the same speed/duplex as the PHY. */ - ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ - ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ - E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ - E1000_CTRL_SPD_100 |/* Force Speed to 100 */ - E1000_CTRL_FD); /* Force Duplex to FULL */ - } else { - /* force 1000, set loopback */ - e1000_write_phy_reg(hw, PHY_CTRL, 0x4140); - - /* Now set up the MAC to the same speed/duplex as the PHY. */ - ctrl_reg = er32(CTRL); - ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ - ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ - E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ - E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */ - E1000_CTRL_FD); /* Force Duplex to FULL */ - } + /* Now set up the MAC to the same speed/duplex as the PHY. */ + ctrl_reg = er32(CTRL); + ctrl_reg &= ~E1000_CTRL_SPD_SEL; /* Clear the speed sel bits */ + ctrl_reg |= (E1000_CTRL_FRCSPD | /* Set the Force Speed Bit */ + E1000_CTRL_FRCDPX | /* Set the Force Duplex Bit */ + E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */ + E1000_CTRL_FD); /* Force Duplex to FULL */ if (hw->media_type == e1000_media_type_copper && hw->phy_type == e1000_phy_m88) @@ -1373,14 +1301,8 @@ static int e1000_set_phy_loopback(struct e1000_adapter *adapter) case e1000_82541_rev_2: case e1000_82547: case e1000_82547_rev_2: - case e1000_82571: - case e1000_82572: - case e1000_82573: - case e1000_80003es2lan: - case e1000_ich8lan: return e1000_integrated_phy_loopback(adapter); break; - default: /* Default PHY loopback work is to read the MII * control register and assert bit 14 (loopback mode). @@ -1409,14 +1331,6 @@ static int e1000_setup_loopback_test(struct e1000_adapter *adapter) case e1000_82546_rev_3: return e1000_set_phy_loopback(adapter); break; - case e1000_82571: - case e1000_82572: -#define E1000_SERDES_LB_ON 0x410 - e1000_set_phy_loopback(adapter); - ew32(SCTL, E1000_SERDES_LB_ON); - msleep(10); - return 0; - break; default: rctl = er32(RCTL); rctl |= E1000_RCTL_LBM_TCVR; @@ -1440,26 +1354,12 @@ static void e1000_loopback_cleanup(struct e1000_adapter *adapter) ew32(RCTL, rctl); switch (hw->mac_type) { - case e1000_82571: - case e1000_82572: - if (hw->media_type == e1000_media_type_fiber || - hw->media_type == e1000_media_type_internal_serdes) { -#define E1000_SERDES_LB_OFF 0x400 - ew32(SCTL, E1000_SERDES_LB_OFF); - msleep(10); - break; - } - /* Fall Through */ case e1000_82545: case e1000_82546: case e1000_82545_rev_3: case e1000_82546_rev_3: default: hw->autoneg = true; - if (hw->phy_type == e1000_phy_gg82563) - e1000_write_phy_reg(hw, - GG82563_PHY_KMRN_MODE_CTRL, - 0x180); e1000_read_phy_reg(hw, PHY_CTRL, &phy_reg); if (phy_reg & MII_CR_LOOPBACK) { phy_reg &= ~MII_CR_LOOPBACK; @@ -1560,17 +1460,6 @@ static int e1000_run_loopback_test(struct e1000_adapter *adapter) static int e1000_loopback_test(struct e1000_adapter *adapter, u64 *data) { - struct e1000_hw *hw = &adapter->hw; - - /* PHY loopback cannot be performed if SoL/IDER - * sessions are active */ - if (e1000_check_phy_reset_block(hw)) { - DPRINTK(DRV, ERR, "Cannot do PHY loopback test " - "when SoL/IDER is active.\n"); - *data = 0; - goto out; - } - *data = e1000_setup_desc_rings(adapter); if (*data) goto out; @@ -1592,13 +1481,13 @@ static int e1000_link_test(struct e1000_adapter *adapter, u64 *data) *data = 0; if (hw->media_type == e1000_media_type_internal_serdes) { int i = 0; - hw->serdes_link_down = true; + hw->serdes_has_link = false; /* On some blade server designs, link establishment * could take as long as 2-3 minutes */ do { e1000_check_for_link(hw); - if (!hw->serdes_link_down) + if (hw->serdes_has_link) return *data; msleep(20); } while (i++ < 3750); @@ -1716,15 +1605,11 @@ static int e1000_wol_exclusion(struct e1000_adapter *adapter, case E1000_DEV_ID_82545EM_COPPER: case E1000_DEV_ID_82546GB_QUAD_COPPER: case E1000_DEV_ID_82546GB_PCIE: - case E1000_DEV_ID_82571EB_SERDES_QUAD: /* these don't support WoL at all */ wol->supported = 0; break; case E1000_DEV_ID_82546EB_FIBER: case E1000_DEV_ID_82546GB_FIBER: - case E1000_DEV_ID_82571EB_FIBER: - case E1000_DEV_ID_82571EB_SERDES: - case E1000_DEV_ID_82571EB_COPPER: /* Wake events not supported on port B */ if (er32(STATUS) & E1000_STATUS_FUNC_1) { wol->supported = 0; @@ -1733,10 +1618,6 @@ static int e1000_wol_exclusion(struct e1000_adapter *adapter, /* return success for non excluded adapter ports */ retval = 0; break; - case E1000_DEV_ID_82571EB_QUAD_COPPER: - case E1000_DEV_ID_82571EB_QUAD_FIBER: - case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: - case E1000_DEV_ID_82571PT_QUAD_COPPER: case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: /* quad port adapters only support WoL on port A */ if (!adapter->quad_port_a) { @@ -1872,30 +1753,15 @@ static int e1000_phys_id(struct net_device *netdev, u32 data) if (!data) data = INT_MAX; - if (hw->mac_type < e1000_82571) { - if (!adapter->blink_timer.function) { - init_timer(&adapter->blink_timer); - adapter->blink_timer.function = e1000_led_blink_callback; - adapter->blink_timer.data = (unsigned long)adapter; - } - e1000_setup_led(hw); - mod_timer(&adapter->blink_timer, jiffies); - msleep_interruptible(data * 1000); - del_timer_sync(&adapter->blink_timer); - } else if (hw->phy_type == e1000_phy_ife) { - if (!adapter->blink_timer.function) { - init_timer(&adapter->blink_timer); - adapter->blink_timer.function = e1000_led_blink_callback; - adapter->blink_timer.data = (unsigned long)adapter; - } - mod_timer(&adapter->blink_timer, jiffies); - msleep_interruptible(data * 1000); - del_timer_sync(&adapter->blink_timer); - e1000_write_phy_reg(&(adapter->hw), IFE_PHY_SPECIAL_CONTROL_LED, 0); - } else { - e1000_blink_led_start(hw); - msleep_interruptible(data * 1000); + if (!adapter->blink_timer.function) { + init_timer(&adapter->blink_timer); + adapter->blink_timer.function = e1000_led_blink_callback; + adapter->blink_timer.data = (unsigned long)adapter; } + e1000_setup_led(hw); + mod_timer(&adapter->blink_timer, jiffies); + msleep_interruptible(data * 1000); + del_timer_sync(&adapter->blink_timer); e1000_led_off(hw); clear_bit(E1000_LED_ON, &adapter->led_status); diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c index cda6b397550..8d7d87f1282 100644 --- a/drivers/net/e1000/e1000_hw.c +++ b/drivers/net/e1000/e1000_hw.c @@ -24,88 +24,34 @@ e1000-devel Mailing List <e1000-devel@lists.sourceforge.net> Intel Corporation, 5200 N.E. Elam Young Parkway, Hillsboro, OR 97124-6497 -*******************************************************************************/ + */ /* e1000_hw.c * Shared functions for accessing and configuring the MAC */ - #include "e1000_hw.h" -static s32 e1000_swfw_sync_acquire(struct e1000_hw *hw, u16 mask); -static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask); -static s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 *data); -static s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 data); -static s32 e1000_get_software_semaphore(struct e1000_hw *hw); -static void e1000_release_software_semaphore(struct e1000_hw *hw); - -static u8 e1000_arc_subsystem_valid(struct e1000_hw *hw); static s32 e1000_check_downshift(struct e1000_hw *hw); static s32 e1000_check_polarity(struct e1000_hw *hw, e1000_rev_polarity *polarity); static void e1000_clear_hw_cntrs(struct e1000_hw *hw); static void e1000_clear_vfta(struct e1000_hw *hw); -static s32 e1000_commit_shadow_ram(struct e1000_hw *hw); static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up); static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw); static s32 e1000_detect_gig_phy(struct e1000_hw *hw); -static s32 e1000_erase_ich8_4k_segment(struct e1000_hw *hw, u32 bank); static s32 e1000_get_auto_rd_done(struct e1000_hw *hw); static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length, u16 *max_length); -static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw); static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw); -static s32 e1000_get_software_flag(struct e1000_hw *hw); -static s32 e1000_ich8_cycle_init(struct e1000_hw *hw); -static s32 e1000_ich8_flash_cycle(struct e1000_hw *hw, u32 timeout); static s32 e1000_id_led_init(struct e1000_hw *hw); -static s32 e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, - u32 cnf_base_addr, - u32 cnf_size); -static s32 e1000_init_lcd_from_nvm(struct e1000_hw *hw); static void e1000_init_rx_addrs(struct e1000_hw *hw); -static void e1000_initialize_hardware_bits(struct e1000_hw *hw); -static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw); -static s32 e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw); -static s32 e1000_mng_enable_host_if(struct e1000_hw *hw); -static s32 e1000_mng_host_if_write(struct e1000_hw *hw, u8 *buffer, u16 length, - u16 offset, u8 *sum); -static s32 e1000_mng_write_cmd_header(struct e1000_hw* hw, - struct e1000_host_mng_command_header - *hdr); -static s32 e1000_mng_write_commit(struct e1000_hw *hw); -static s32 e1000_phy_ife_get_info(struct e1000_hw *hw, - struct e1000_phy_info *phy_info); static s32 e1000_phy_igp_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); -static s32 e1000_read_eeprom_eerd(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data); -static s32 e1000_write_eeprom_eewr(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data); -static s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd); static s32 e1000_phy_m88_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); -static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw); -static s32 e1000_read_ich8_byte(struct e1000_hw *hw, u32 index, u8 *data); -static s32 e1000_verify_write_ich8_byte(struct e1000_hw *hw, u32 index, - u8 byte); -static s32 e1000_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 byte); -static s32 e1000_read_ich8_word(struct e1000_hw *hw, u32 index, u16 *data); -static s32 e1000_read_ich8_data(struct e1000_hw *hw, u32 index, u32 size, - u16 *data); -static s32 e1000_write_ich8_data(struct e1000_hw *hw, u32 index, u32 size, - u16 data); -static s32 e1000_read_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data); -static s32 e1000_write_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data); -static void e1000_release_software_flag(struct e1000_hw *hw); static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active); -static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active); -static s32 e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, u32 no_snoop); -static void e1000_set_pci_express_master_disable(struct e1000_hw *hw); static s32 e1000_wait_autoneg(struct e1000_hw *hw); static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value); static s32 e1000_set_phy_type(struct e1000_hw *hw); @@ -117,12 +63,11 @@ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw); static s32 e1000_config_mac_to_phy(struct e1000_hw *hw); static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl); static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl); -static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, - u16 count); +static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count); static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw); static s32 e1000_phy_reset_dsp(struct e1000_hw *hw); static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, - u16 words, u16 *data); + u16 words, u16 *data); static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw); @@ -131,7 +76,7 @@ static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd); static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count); static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, u16 phy_data); -static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw,u32 reg_addr, +static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data); static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count); static s32 e1000_acquire_eeprom(struct e1000_hw *hw); @@ -140,188 +85,164 @@ static void e1000_standby_eeprom(struct e1000_hw *hw); static s32 e1000_set_vco_speed(struct e1000_hw *hw); static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw); static s32 e1000_set_phy_mode(struct e1000_hw *hw); -static s32 e1000_host_if_read_cookie(struct e1000_hw *hw, u8 *buffer); -static u8 e1000_calculate_mng_checksum(char *buffer, u32 length); -static s32 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, u16 duplex); -static s32 e1000_configure_kmrn_for_1000(struct e1000_hw *hw); -static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); -static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data); +static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data); +static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data); /* IGP cable length table */ static const -u16 e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] = - { 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, - 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25, - 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40, - 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60, - 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90, - 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, 100, - 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, - 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, 120, 120}; - -static const -u16 e1000_igp_2_cable_length_table[IGP02E1000_AGC_LENGTH_TABLE_SIZE] = - { 0, 0, 0, 0, 0, 0, 0, 0, 3, 5, 8, 11, 13, 16, 18, 21, - 0, 0, 0, 3, 6, 10, 13, 16, 19, 23, 26, 29, 32, 35, 38, 41, - 6, 10, 14, 18, 22, 26, 30, 33, 37, 41, 44, 48, 51, 54, 58, 61, - 21, 26, 31, 35, 40, 44, 49, 53, 57, 61, 65, 68, 72, 75, 79, 82, - 40, 45, 51, 56, 61, 66, 70, 75, 79, 83, 87, 91, 94, 98, 101, 104, - 60, 66, 72, 77, 82, 87, 92, 96, 100, 104, 108, 111, 114, 117, 119, 121, - 83, 89, 95, 100, 105, 109, 113, 116, 119, 122, 124, - 104, 109, 114, 118, 121, 124}; +u16 e1000_igp_cable_length_table[IGP01E1000_AGC_LENGTH_TABLE_SIZE] = { + 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, 5, + 5, 10, 10, 10, 10, 10, 10, 10, 20, 20, 20, 20, 20, 25, 25, 25, + 25, 25, 25, 25, 30, 30, 30, 30, 40, 40, 40, 40, 40, 40, 40, 40, + 40, 50, 50, 50, 50, 50, 50, 50, 60, 60, 60, 60, 60, 60, 60, 60, + 60, 70, 70, 70, 70, 70, 70, 80, 80, 80, 80, 80, 80, 90, 90, 90, + 90, 90, 90, 90, 90, 90, 100, 100, 100, 100, 100, 100, 100, 100, 100, + 100, + 100, 100, 100, 100, 110, 110, 110, 110, 110, 110, 110, 110, 110, 110, + 110, 110, + 110, 110, 110, 110, 110, 110, 120, 120, 120, 120, 120, 120, 120, 120, + 120, 120 +}; static DEFINE_SPINLOCK(e1000_eeprom_lock); -/****************************************************************************** - * Set the phy type member in the hw struct. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_set_phy_type - Set the phy type member in the hw struct. + * @hw: Struct containing variables accessed by shared code + */ static s32 e1000_set_phy_type(struct e1000_hw *hw) { - DEBUGFUNC("e1000_set_phy_type"); - - if (hw->mac_type == e1000_undefined) - return -E1000_ERR_PHY_TYPE; - - switch (hw->phy_id) { - case M88E1000_E_PHY_ID: - case M88E1000_I_PHY_ID: - case M88E1011_I_PHY_ID: - case M88E1111_I_PHY_ID: - hw->phy_type = e1000_phy_m88; - break; - case IGP01E1000_I_PHY_ID: - if (hw->mac_type == e1000_82541 || - hw->mac_type == e1000_82541_rev_2 || - hw->mac_type == e1000_82547 || - hw->mac_type == e1000_82547_rev_2) { - hw->phy_type = e1000_phy_igp; - break; - } - case IGP03E1000_E_PHY_ID: - hw->phy_type = e1000_phy_igp_3; - break; - case IFE_E_PHY_ID: - case IFE_PLUS_E_PHY_ID: - case IFE_C_E_PHY_ID: - hw->phy_type = e1000_phy_ife; - break; - case GG82563_E_PHY_ID: - if (hw->mac_type == e1000_80003es2lan) { - hw->phy_type = e1000_phy_gg82563; - break; - } - /* Fall Through */ - default: - /* Should never have loaded on this device */ - hw->phy_type = e1000_phy_undefined; - return -E1000_ERR_PHY_TYPE; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * IGP phy init script - initializes the GbE PHY - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static void e1000_phy_init_script(struct e1000_hw *hw) -{ - u32 ret_val; - u16 phy_saved_data; - - DEBUGFUNC("e1000_phy_init_script"); - - if (hw->phy_init_script) { - msleep(20); - - /* Save off the current value of register 0x2F5B to be restored at - * the end of this routine. */ - ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); - - /* Disabled the PHY transmitter */ - e1000_write_phy_reg(hw, 0x2F5B, 0x0003); + DEBUGFUNC("e1000_set_phy_type"); - msleep(20); + if (hw->mac_type == e1000_undefined) + return -E1000_ERR_PHY_TYPE; - e1000_write_phy_reg(hw,0x0000,0x0140); - - msleep(5); - - switch (hw->mac_type) { - case e1000_82541: - case e1000_82547: - e1000_write_phy_reg(hw, 0x1F95, 0x0001); - - e1000_write_phy_reg(hw, 0x1F71, 0xBD21); - - e1000_write_phy_reg(hw, 0x1F79, 0x0018); - - e1000_write_phy_reg(hw, 0x1F30, 0x1600); - - e1000_write_phy_reg(hw, 0x1F31, 0x0014); - - e1000_write_phy_reg(hw, 0x1F32, 0x161C); - - e1000_write_phy_reg(hw, 0x1F94, 0x0003); - - e1000_write_phy_reg(hw, 0x1F96, 0x003F); - - e1000_write_phy_reg(hw, 0x2010, 0x0008); - break; - - case e1000_82541_rev_2: - case e1000_82547_rev_2: - e1000_write_phy_reg(hw, 0x1F73, 0x0099); - break; - default: - break; - } - - e1000_write_phy_reg(hw, 0x0000, 0x3300); - - msleep(20); - - /* Now enable the transmitter */ - e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); - - if (hw->mac_type == e1000_82547) { - u16 fused, fine, coarse; - - /* Move to analog registers page */ - e1000_read_phy_reg(hw, IGP01E1000_ANALOG_SPARE_FUSE_STATUS, &fused); - - if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { - e1000_read_phy_reg(hw, IGP01E1000_ANALOG_FUSE_STATUS, &fused); + switch (hw->phy_id) { + case M88E1000_E_PHY_ID: + case M88E1000_I_PHY_ID: + case M88E1011_I_PHY_ID: + case M88E1111_I_PHY_ID: + hw->phy_type = e1000_phy_m88; + break; + case IGP01E1000_I_PHY_ID: + if (hw->mac_type == e1000_82541 || + hw->mac_type == e1000_82541_rev_2 || + hw->mac_type == e1000_82547 || + hw->mac_type == e1000_82547_rev_2) { + hw->phy_type = e1000_phy_igp; + break; + } + default: + /* Should never have loaded on this device */ + hw->phy_type = e1000_phy_undefined; + return -E1000_ERR_PHY_TYPE; + } - fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; - coarse = fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK; + return E1000_SUCCESS; +} - if (coarse > IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { - coarse -= IGP01E1000_ANALOG_FUSE_COARSE_10; - fine -= IGP01E1000_ANALOG_FUSE_FINE_1; - } else if (coarse == IGP01E1000_ANALOG_FUSE_COARSE_THRESH) - fine -= IGP01E1000_ANALOG_FUSE_FINE_10; +/** + * e1000_phy_init_script - IGP phy init script - initializes the GbE PHY + * @hw: Struct containing variables accessed by shared code + */ +static void e1000_phy_init_script(struct e1000_hw *hw) +{ + u32 ret_val; + u16 phy_saved_data; + + DEBUGFUNC("e1000_phy_init_script"); + + if (hw->phy_init_script) { + msleep(20); + + /* Save off the current value of register 0x2F5B to be restored at + * the end of this routine. */ + ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); + + /* Disabled the PHY transmitter */ + e1000_write_phy_reg(hw, 0x2F5B, 0x0003); + msleep(20); + + e1000_write_phy_reg(hw, 0x0000, 0x0140); + msleep(5); + + switch (hw->mac_type) { + case e1000_82541: + case e1000_82547: + e1000_write_phy_reg(hw, 0x1F95, 0x0001); + e1000_write_phy_reg(hw, 0x1F71, 0xBD21); + e1000_write_phy_reg(hw, 0x1F79, 0x0018); + e1000_write_phy_reg(hw, 0x1F30, 0x1600); + e1000_write_phy_reg(hw, 0x1F31, 0x0014); + e1000_write_phy_reg(hw, 0x1F32, 0x161C); + e1000_write_phy_reg(hw, 0x1F94, 0x0003); + e1000_write_phy_reg(hw, 0x1F96, 0x003F); + e1000_write_phy_reg(hw, 0x2010, 0x0008); + break; - fused = (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) | - (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) | - (coarse & IGP01E1000_ANALOG_FUSE_COARSE_MASK); + case e1000_82541_rev_2: + case e1000_82547_rev_2: + e1000_write_phy_reg(hw, 0x1F73, 0x0099); + break; + default: + break; + } - e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_CONTROL, fused); - e1000_write_phy_reg(hw, IGP01E1000_ANALOG_FUSE_BYPASS, - IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); - } - } - } + e1000_write_phy_reg(hw, 0x0000, 0x3300); + msleep(20); + + /* Now enable the transmitter */ + e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); + + if (hw->mac_type == e1000_82547) { + u16 fused, fine, coarse; + + /* Move to analog registers page */ + e1000_read_phy_reg(hw, + IGP01E1000_ANALOG_SPARE_FUSE_STATUS, + &fused); + + if (!(fused & IGP01E1000_ANALOG_SPARE_FUSE_ENABLED)) { + e1000_read_phy_reg(hw, + IGP01E1000_ANALOG_FUSE_STATUS, + &fused); + + fine = fused & IGP01E1000_ANALOG_FUSE_FINE_MASK; + coarse = + fused & IGP01E1000_ANALOG_FUSE_COARSE_MASK; + + if (coarse > + IGP01E1000_ANALOG_FUSE_COARSE_THRESH) { + coarse -= + IGP01E1000_ANALOG_FUSE_COARSE_10; + fine -= IGP01E1000_ANALOG_FUSE_FINE_1; + } else if (coarse == + IGP01E1000_ANALOG_FUSE_COARSE_THRESH) + fine -= IGP01E1000_ANALOG_FUSE_FINE_10; + + fused = + (fused & IGP01E1000_ANALOG_FUSE_POLY_MASK) | + (fine & IGP01E1000_ANALOG_FUSE_FINE_MASK) | + (coarse & + IGP01E1000_ANALOG_FUSE_COARSE_MASK); + + e1000_write_phy_reg(hw, + IGP01E1000_ANALOG_FUSE_CONTROL, + fused); + e1000_write_phy_reg(hw, + IGP01E1000_ANALOG_FUSE_BYPASS, + IGP01E1000_ANALOG_FUSE_ENABLE_SW_CONTROL); + } + } + } } -/****************************************************************************** - * Set the mac type member in the hw struct. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_set_mac_type - Set the mac type member in the hw struct. + * @hw: Struct containing variables accessed by shared code + */ s32 e1000_set_mac_type(struct e1000_hw *hw) { DEBUGFUNC("e1000_set_mac_type"); @@ -397,61 +318,12 @@ s32 e1000_set_mac_type(struct e1000_hw *hw) case E1000_DEV_ID_82547GI: hw->mac_type = e1000_82547_rev_2; break; - case E1000_DEV_ID_82571EB_COPPER: - case E1000_DEV_ID_82571EB_FIBER: - case E1000_DEV_ID_82571EB_SERDES: - case E1000_DEV_ID_82571EB_SERDES_DUAL: - case E1000_DEV_ID_82571EB_SERDES_QUAD: - case E1000_DEV_ID_82571EB_QUAD_COPPER: - case E1000_DEV_ID_82571PT_QUAD_COPPER: - case E1000_DEV_ID_82571EB_QUAD_FIBER: - case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: - hw->mac_type = e1000_82571; - break; - case E1000_DEV_ID_82572EI_COPPER: - case E1000_DEV_ID_82572EI_FIBER: - case E1000_DEV_ID_82572EI_SERDES: - case E1000_DEV_ID_82572EI: - hw->mac_type = e1000_82572; - break; - case E1000_DEV_ID_82573E: - case E1000_DEV_ID_82573E_IAMT: - case E1000_DEV_ID_82573L: - hw->mac_type = e1000_82573; - break; - case E1000_DEV_ID_80003ES2LAN_COPPER_SPT: - case E1000_DEV_ID_80003ES2LAN_SERDES_SPT: - case E1000_DEV_ID_80003ES2LAN_COPPER_DPT: - case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: - hw->mac_type = e1000_80003es2lan; - break; - case E1000_DEV_ID_ICH8_IGP_M_AMT: - case E1000_DEV_ID_ICH8_IGP_AMT: - case E1000_DEV_ID_ICH8_IGP_C: - case E1000_DEV_ID_ICH8_IFE: - case E1000_DEV_ID_ICH8_IFE_GT: - case E1000_DEV_ID_ICH8_IFE_G: - case E1000_DEV_ID_ICH8_IGP_M: - hw->mac_type = e1000_ich8lan; - break; default: /* Should never have loaded on this device */ return -E1000_ERR_MAC_TYPE; } switch (hw->mac_type) { - case e1000_ich8lan: - hw->swfwhw_semaphore_present = true; - hw->asf_firmware_present = true; - break; - case e1000_80003es2lan: - hw->swfw_sync_present = true; - /* fall through */ - case e1000_82571: - case e1000_82572: - case e1000_82573: - hw->eeprom_semaphore_present = true; - /* fall through */ case e1000_82541: case e1000_82547: case e1000_82541_rev_2: @@ -468,6058 +340,4500 @@ s32 e1000_set_mac_type(struct e1000_hw *hw) if (hw->mac_type == e1000_82543) hw->bad_tx_carr_stats_fd = true; - /* capable of receiving management packets to the host */ - if (hw->mac_type >= e1000_82571) - hw->has_manc2h = true; - - /* In rare occasions, ESB2 systems would end up started without - * the RX unit being turned on. - */ - if (hw->mac_type == e1000_80003es2lan) - hw->rx_needs_kicking = true; - if (hw->mac_type > e1000_82544) hw->has_smbus = true; return E1000_SUCCESS; } -/***************************************************************************** - * Set media type and TBI compatibility. - * - * hw - Struct containing variables accessed by shared code - * **************************************************************************/ +/** + * e1000_set_media_type - Set media type and TBI compatibility. + * @hw: Struct containing variables accessed by shared code + */ void e1000_set_media_type(struct e1000_hw *hw) { - u32 status; - - DEBUGFUNC("e1000_set_media_type"); - - if (hw->mac_type != e1000_82543) { - /* tbi_compatibility is only valid on 82543 */ - hw->tbi_compatibility_en = false; - } - - switch (hw->device_id) { - case E1000_DEV_ID_82545GM_SERDES: - case E1000_DEV_ID_82546GB_SERDES: - case E1000_DEV_ID_82571EB_SERDES: - case E1000_DEV_ID_82571EB_SERDES_DUAL: - case E1000_DEV_ID_82571EB_SERDES_QUAD: - case E1000_DEV_ID_82572EI_SERDES: - case E1000_DEV_ID_80003ES2LAN_SERDES_DPT: - hw->media_type = e1000_media_type_internal_serdes; - break; - default: - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - hw->media_type = e1000_media_type_fiber; - break; - case e1000_ich8lan: - case e1000_82573: - /* The STATUS_TBIMODE bit is reserved or reused for the this - * device. - */ - hw->media_type = e1000_media_type_copper; - break; - default: - status = er32(STATUS); - if (status & E1000_STATUS_TBIMODE) { - hw->media_type = e1000_media_type_fiber; - /* tbi_compatibility not valid on fiber */ - hw->tbi_compatibility_en = false; - } else { - hw->media_type = e1000_media_type_copper; - } - break; - } - } + u32 status; + + DEBUGFUNC("e1000_set_media_type"); + + if (hw->mac_type != e1000_82543) { + /* tbi_compatibility is only valid on 82543 */ + hw->tbi_compatibility_en = false; + } + + switch (hw->device_id) { + case E1000_DEV_ID_82545GM_SERDES: + case E1000_DEV_ID_82546GB_SERDES: + hw->media_type = e1000_media_type_internal_serdes; + break; + default: + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + hw->media_type = e1000_media_type_fiber; + break; + default: + status = er32(STATUS); + if (status & E1000_STATUS_TBIMODE) { + hw->media_type = e1000_media_type_fiber; + /* tbi_compatibility not valid on fiber */ + hw->tbi_compatibility_en = false; + } else { + hw->media_type = e1000_media_type_copper; + } + break; + } + } } -/****************************************************************************** - * Reset the transmit and receive units; mask and clear all interrupts. +/** + * e1000_reset_hw: reset the hardware completely + * @hw: Struct containing variables accessed by shared code * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ + * Reset the transmit and receive units; mask and clear all interrupts. + */ s32 e1000_reset_hw(struct e1000_hw *hw) { - u32 ctrl; - u32 ctrl_ext; - u32 icr; - u32 manc; - u32 led_ctrl; - u32 timeout; - u32 extcnf_ctrl; - s32 ret_val; - - DEBUGFUNC("e1000_reset_hw"); - - /* For 82542 (rev 2.0), disable MWI before issuing a device reset */ - if (hw->mac_type == e1000_82542_rev2_0) { - DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); - e1000_pci_clear_mwi(hw); - } - - if (hw->bus_type == e1000_bus_type_pci_express) { - /* Prevent the PCI-E bus from sticking if there is no TLP connection - * on the last TLP read/write transaction when MAC is reset. - */ - if (e1000_disable_pciex_master(hw) != E1000_SUCCESS) { - DEBUGOUT("PCI-E Master disable polling has failed.\n"); - } - } - - /* Clear interrupt mask to stop board from generating interrupts */ - DEBUGOUT("Masking off all interrupts\n"); - ew32(IMC, 0xffffffff); - - /* Disable the Transmit and Receive units. Then delay to allow - * any pending transactions to complete before we hit the MAC with - * the global reset. - */ - ew32(RCTL, 0); - ew32(TCTL, E1000_TCTL_PSP); - E1000_WRITE_FLUSH(); - - /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */ - hw->tbi_compatibility_on = false; - - /* Delay to allow any outstanding PCI transactions to complete before - * resetting the device - */ - msleep(10); - - ctrl = er32(CTRL); - - /* Must reset the PHY before resetting the MAC */ - if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { - ew32(CTRL, (ctrl | E1000_CTRL_PHY_RST)); - msleep(5); - } - - /* Must acquire the MDIO ownership before MAC reset. - * Ownership defaults to firmware after a reset. */ - if (hw->mac_type == e1000_82573) { - timeout = 10; - - extcnf_ctrl = er32(EXTCNF_CTRL); - extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; - - do { - ew32(EXTCNF_CTRL, extcnf_ctrl); - extcnf_ctrl = er32(EXTCNF_CTRL); - - if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP) - break; - else - extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP; - - msleep(2); - timeout--; - } while (timeout); - } - - /* Workaround for ICH8 bit corruption issue in FIFO memory */ - if (hw->mac_type == e1000_ich8lan) { - /* Set Tx and Rx buffer allocation to 8k apiece. */ - ew32(PBA, E1000_PBA_8K); - /* Set Packet Buffer Size to 16k. */ - ew32(PBS, E1000_PBS_16K); - } - - /* Issue a global reset to the MAC. This will reset the chip's - * transmit, receive, DMA, and link units. It will not effect - * the current PCI configuration. The global reset bit is self- - * clearing, and should clear within a microsecond. - */ - DEBUGOUT("Issuing a global reset to MAC\n"); - - switch (hw->mac_type) { - case e1000_82544: - case e1000_82540: - case e1000_82545: - case e1000_82546: - case e1000_82541: - case e1000_82541_rev_2: - /* These controllers can't ack the 64-bit write when issuing the - * reset, so use IO-mapping as a workaround to issue the reset */ - E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST)); - break; - case e1000_82545_rev_3: - case e1000_82546_rev_3: - /* Reset is performed on a shadow of the control register */ - ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST)); - break; - case e1000_ich8lan: - if (!hw->phy_reset_disable && - e1000_check_phy_reset_block(hw) == E1000_SUCCESS) { - /* e1000_ich8lan PHY HW reset requires MAC CORE reset - * at the same time to make sure the interface between - * MAC and the external PHY is reset. - */ - ctrl |= E1000_CTRL_PHY_RST; - } - - e1000_get_software_flag(hw); - ew32(CTRL, (ctrl | E1000_CTRL_RST)); - msleep(5); - break; - default: - ew32(CTRL, (ctrl | E1000_CTRL_RST)); - break; - } - - /* After MAC reset, force reload of EEPROM to restore power-on settings to - * device. Later controllers reload the EEPROM automatically, so just wait - * for reload to complete. - */ - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - case e1000_82543: - case e1000_82544: - /* Wait for reset to complete */ - udelay(10); - ctrl_ext = er32(CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_EE_RST; - ew32(CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(); - /* Wait for EEPROM reload */ - msleep(2); - break; - case e1000_82541: - case e1000_82541_rev_2: - case e1000_82547: - case e1000_82547_rev_2: - /* Wait for EEPROM reload */ - msleep(20); - break; - case e1000_82573: - if (!e1000_is_onboard_nvm_eeprom(hw)) { - udelay(10); - ctrl_ext = er32(CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_EE_RST; - ew32(CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(); - } - /* fall through */ - default: - /* Auto read done will delay 5ms or poll based on mac type */ - ret_val = e1000_get_auto_rd_done(hw); - if (ret_val) - return ret_val; - break; - } - - /* Disable HW ARPs on ASF enabled adapters */ - if (hw->mac_type >= e1000_82540 && hw->mac_type <= e1000_82547_rev_2) { - manc = er32(MANC); - manc &= ~(E1000_MANC_ARP_EN); - ew32(MANC, manc); - } - - if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { - e1000_phy_init_script(hw); - - /* Configure activity LED after PHY reset */ - led_ctrl = er32(LEDCTL); - led_ctrl &= IGP_ACTIVITY_LED_MASK; - led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); - ew32(LEDCTL, led_ctrl); - } - - /* Clear interrupt mask to stop board from generating interrupts */ - DEBUGOUT("Masking off all interrupts\n"); - ew32(IMC, 0xffffffff); - - /* Clear any pending interrupt events. */ - icr = er32(ICR); - - /* If MWI was previously enabled, reenable it. */ - if (hw->mac_type == e1000_82542_rev2_0) { - if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE) - e1000_pci_set_mwi(hw); - } - - if (hw->mac_type == e1000_ich8lan) { - u32 kab = er32(KABGTXD); - kab |= E1000_KABGTXD_BGSQLBIAS; - ew32(KABGTXD, kab); - } - - return E1000_SUCCESS; -} + u32 ctrl; + u32 ctrl_ext; + u32 icr; + u32 manc; + u32 led_ctrl; + s32 ret_val; -/****************************************************************************** - * - * Initialize a number of hardware-dependent bits - * - * hw: Struct containing variables accessed by shared code - * - * This function contains hardware limitation workarounds for PCI-E adapters - * - *****************************************************************************/ -static void e1000_initialize_hardware_bits(struct e1000_hw *hw) -{ - if ((hw->mac_type >= e1000_82571) && (!hw->initialize_hw_bits_disable)) { - /* Settings common to all PCI-express silicon */ - u32 reg_ctrl, reg_ctrl_ext; - u32 reg_tarc0, reg_tarc1; - u32 reg_tctl; - u32 reg_txdctl, reg_txdctl1; - - /* link autonegotiation/sync workarounds */ - reg_tarc0 = er32(TARC0); - reg_tarc0 &= ~((1 << 30)|(1 << 29)|(1 << 28)|(1 << 27)); - - /* Enable not-done TX descriptor counting */ - reg_txdctl = er32(TXDCTL); - reg_txdctl |= E1000_TXDCTL_COUNT_DESC; - ew32(TXDCTL, reg_txdctl); - reg_txdctl1 = er32(TXDCTL1); - reg_txdctl1 |= E1000_TXDCTL_COUNT_DESC; - ew32(TXDCTL1, reg_txdctl1); - - switch (hw->mac_type) { - case e1000_82571: - case e1000_82572: - /* Clear PHY TX compatible mode bits */ - reg_tarc1 = er32(TARC1); - reg_tarc1 &= ~((1 << 30)|(1 << 29)); - - /* link autonegotiation/sync workarounds */ - reg_tarc0 |= ((1 << 26)|(1 << 25)|(1 << 24)|(1 << 23)); - - /* TX ring control fixes */ - reg_tarc1 |= ((1 << 26)|(1 << 25)|(1 << 24)); - - /* Multiple read bit is reversed polarity */ - reg_tctl = er32(TCTL); - if (reg_tctl & E1000_TCTL_MULR) - reg_tarc1 &= ~(1 << 28); - else - reg_tarc1 |= (1 << 28); - - ew32(TARC1, reg_tarc1); - break; - case e1000_82573: - reg_ctrl_ext = er32(CTRL_EXT); - reg_ctrl_ext &= ~(1 << 23); - reg_ctrl_ext |= (1 << 22); - - /* TX byte count fix */ - reg_ctrl = er32(CTRL); - reg_ctrl &= ~(1 << 29); - - ew32(CTRL_EXT, reg_ctrl_ext); - ew32(CTRL, reg_ctrl); - break; - case e1000_80003es2lan: - /* improve small packet performace for fiber/serdes */ - if ((hw->media_type == e1000_media_type_fiber) || - (hw->media_type == e1000_media_type_internal_serdes)) { - reg_tarc0 &= ~(1 << 20); - } - - /* Multiple read bit is reversed polarity */ - reg_tctl = er32(TCTL); - reg_tarc1 = er32(TARC1); - if (reg_tctl & E1000_TCTL_MULR) - reg_tarc1 &= ~(1 << 28); - else - reg_tarc1 |= (1 << 28); - - ew32(TARC1, reg_tarc1); - break; - case e1000_ich8lan: - /* Reduce concurrent DMA requests to 3 from 4 */ - if ((hw->revision_id < 3) || - ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && - (hw->device_id != E1000_DEV_ID_ICH8_IGP_M))) - reg_tarc0 |= ((1 << 29)|(1 << 28)); - - reg_ctrl_ext = er32(CTRL_EXT); - reg_ctrl_ext |= (1 << 22); - ew32(CTRL_EXT, reg_ctrl_ext); - - /* workaround TX hang with TSO=on */ - reg_tarc0 |= ((1 << 27)|(1 << 26)|(1 << 24)|(1 << 23)); - - /* Multiple read bit is reversed polarity */ - reg_tctl = er32(TCTL); - reg_tarc1 = er32(TARC1); - if (reg_tctl & E1000_TCTL_MULR) - reg_tarc1 &= ~(1 << 28); - else - reg_tarc1 |= (1 << 28); - - /* workaround TX hang with TSO=on */ - reg_tarc1 |= ((1 << 30)|(1 << 26)|(1 << 24)); - - ew32(TARC1, reg_tarc1); - break; - default: - break; - } - - ew32(TARC0, reg_tarc0); - } + DEBUGFUNC("e1000_reset_hw"); + + /* For 82542 (rev 2.0), disable MWI before issuing a device reset */ + if (hw->mac_type == e1000_82542_rev2_0) { + DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); + e1000_pci_clear_mwi(hw); + } + + /* Clear interrupt mask to stop board from generating interrupts */ + DEBUGOUT("Masking off all interrupts\n"); + ew32(IMC, 0xffffffff); + + /* Disable the Transmit and Receive units. Then delay to allow + * any pending transactions to complete before we hit the MAC with + * the global reset. + */ + ew32(RCTL, 0); + ew32(TCTL, E1000_TCTL_PSP); + E1000_WRITE_FLUSH(); + + /* The tbi_compatibility_on Flag must be cleared when Rctl is cleared. */ + hw->tbi_compatibility_on = false; + + /* Delay to allow any outstanding PCI transactions to complete before + * resetting the device + */ + msleep(10); + + ctrl = er32(CTRL); + + /* Must reset the PHY before resetting the MAC */ + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + ew32(CTRL, (ctrl | E1000_CTRL_PHY_RST)); + msleep(5); + } + + /* Issue a global reset to the MAC. This will reset the chip's + * transmit, receive, DMA, and link units. It will not effect + * the current PCI configuration. The global reset bit is self- + * clearing, and should clear within a microsecond. + */ + DEBUGOUT("Issuing a global reset to MAC\n"); + + switch (hw->mac_type) { + case e1000_82544: + case e1000_82540: + case e1000_82545: + case e1000_82546: + case e1000_82541: + case e1000_82541_rev_2: + /* These controllers can't ack the 64-bit write when issuing the + * reset, so use IO-mapping as a workaround to issue the reset */ + E1000_WRITE_REG_IO(hw, CTRL, (ctrl | E1000_CTRL_RST)); + break; + case e1000_82545_rev_3: + case e1000_82546_rev_3: + /* Reset is performed on a shadow of the control register */ + ew32(CTRL_DUP, (ctrl | E1000_CTRL_RST)); + break; + default: + ew32(CTRL, (ctrl | E1000_CTRL_RST)); + break; + } + + /* After MAC reset, force reload of EEPROM to restore power-on settings to + * device. Later controllers reload the EEPROM automatically, so just wait + * for reload to complete. + */ + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + /* Wait for reset to complete */ + udelay(10); + ctrl_ext = er32(CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_EE_RST; + ew32(CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(); + /* Wait for EEPROM reload */ + msleep(2); + break; + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + /* Wait for EEPROM reload */ + msleep(20); + break; + default: + /* Auto read done will delay 5ms or poll based on mac type */ + ret_val = e1000_get_auto_rd_done(hw); + if (ret_val) + return ret_val; + break; + } + + /* Disable HW ARPs on ASF enabled adapters */ + if (hw->mac_type >= e1000_82540) { + manc = er32(MANC); + manc &= ~(E1000_MANC_ARP_EN); + ew32(MANC, manc); + } + + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + e1000_phy_init_script(hw); + + /* Configure activity LED after PHY reset */ + led_ctrl = er32(LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + ew32(LEDCTL, led_ctrl); + } + + /* Clear interrupt mask to stop board from generating interrupts */ + DEBUGOUT("Masking off all interrupts\n"); + ew32(IMC, 0xffffffff); + + /* Clear any pending interrupt events. */ + icr = er32(ICR); + + /* If MWI was previously enabled, reenable it. */ + if (hw->mac_type == e1000_82542_rev2_0) { + if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE) + e1000_pci_set_mwi(hw); + } + + return E1000_SUCCESS; } -/****************************************************************************** - * Performs basic configuration of the adapter. - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_init_hw: Performs basic configuration of the adapter. + * @hw: Struct containing variables accessed by shared code * * Assumes that the controller has previously been reset and is in a * post-reset uninitialized state. Initializes the receive address registers, * multicast table, and VLAN filter table. Calls routines to setup link * configuration and flow control settings. Clears all on-chip counters. Leaves * the transmit and receive units disabled and uninitialized. - *****************************************************************************/ + */ s32 e1000_init_hw(struct e1000_hw *hw) { - u32 ctrl; - u32 i; - s32 ret_val; - u32 mta_size; - u32 reg_data; - u32 ctrl_ext; - - DEBUGFUNC("e1000_init_hw"); - - /* force full DMA clock frequency for 10/100 on ICH8 A0-B0 */ - if ((hw->mac_type == e1000_ich8lan) && - ((hw->revision_id < 3) || - ((hw->device_id != E1000_DEV_ID_ICH8_IGP_M_AMT) && - (hw->device_id != E1000_DEV_ID_ICH8_IGP_M)))) { - reg_data = er32(STATUS); - reg_data &= ~0x80000000; - ew32(STATUS, reg_data); - } - - /* Initialize Identification LED */ - ret_val = e1000_id_led_init(hw); - if (ret_val) { - DEBUGOUT("Error Initializing Identification LED\n"); - return ret_val; - } - - /* Set the media type and TBI compatibility */ - e1000_set_media_type(hw); - - /* Must be called after e1000_set_media_type because media_type is used */ - e1000_initialize_hardware_bits(hw); - - /* Disabling VLAN filtering. */ - DEBUGOUT("Initializing the IEEE VLAN\n"); - /* VET hardcoded to standard value and VFTA removed in ICH8 LAN */ - if (hw->mac_type != e1000_ich8lan) { - if (hw->mac_type < e1000_82545_rev_3) - ew32(VET, 0); - e1000_clear_vfta(hw); - } - - /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ - if (hw->mac_type == e1000_82542_rev2_0) { - DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); - e1000_pci_clear_mwi(hw); - ew32(RCTL, E1000_RCTL_RST); - E1000_WRITE_FLUSH(); - msleep(5); - } - - /* Setup the receive address. This involves initializing all of the Receive - * Address Registers (RARs 0 - 15). - */ - e1000_init_rx_addrs(hw); - - /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ - if (hw->mac_type == e1000_82542_rev2_0) { - ew32(RCTL, 0); - E1000_WRITE_FLUSH(); - msleep(1); - if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE) - e1000_pci_set_mwi(hw); - } - - /* Zero out the Multicast HASH table */ - DEBUGOUT("Zeroing the MTA\n"); - mta_size = E1000_MC_TBL_SIZE; - if (hw->mac_type == e1000_ich8lan) - mta_size = E1000_MC_TBL_SIZE_ICH8LAN; - for (i = 0; i < mta_size; i++) { - E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); - /* use write flush to prevent Memory Write Block (MWB) from - * occuring when accessing our register space */ - E1000_WRITE_FLUSH(); - } - - /* Set the PCI priority bit correctly in the CTRL register. This - * determines if the adapter gives priority to receives, or if it - * gives equal priority to transmits and receives. Valid only on - * 82542 and 82543 silicon. - */ - if (hw->dma_fairness && hw->mac_type <= e1000_82543) { - ctrl = er32(CTRL); - ew32(CTRL, ctrl | E1000_CTRL_PRIOR); - } - - switch (hw->mac_type) { - case e1000_82545_rev_3: - case e1000_82546_rev_3: - break; - default: - /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ - if (hw->bus_type == e1000_bus_type_pcix && e1000_pcix_get_mmrbc(hw) > 2048) - e1000_pcix_set_mmrbc(hw, 2048); - break; - } - - /* More time needed for PHY to initialize */ - if (hw->mac_type == e1000_ich8lan) - msleep(15); - - /* Call a subroutine to configure the link and setup flow control. */ - ret_val = e1000_setup_link(hw); - - /* Set the transmit descriptor write-back policy */ - if (hw->mac_type > e1000_82544) { - ctrl = er32(TXDCTL); - ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; - ew32(TXDCTL, ctrl); - } - - if (hw->mac_type == e1000_82573) { - e1000_enable_tx_pkt_filtering(hw); - } - - switch (hw->mac_type) { - default: - break; - case e1000_80003es2lan: - /* Enable retransmit on late collisions */ - reg_data = er32(TCTL); - reg_data |= E1000_TCTL_RTLC; - ew32(TCTL, reg_data); - - /* Configure Gigabit Carry Extend Padding */ - reg_data = er32(TCTL_EXT); - reg_data &= ~E1000_TCTL_EXT_GCEX_MASK; - reg_data |= DEFAULT_80003ES2LAN_TCTL_EXT_GCEX; - ew32(TCTL_EXT, reg_data); - - /* Configure Transmit Inter-Packet Gap */ - reg_data = er32(TIPG); - reg_data &= ~E1000_TIPG_IPGT_MASK; - reg_data |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; - ew32(TIPG, reg_data); - - reg_data = E1000_READ_REG_ARRAY(hw, FFLT, 0x0001); - reg_data &= ~0x00100000; - E1000_WRITE_REG_ARRAY(hw, FFLT, 0x0001, reg_data); - /* Fall through */ - case e1000_82571: - case e1000_82572: - case e1000_ich8lan: - ctrl = er32(TXDCTL1); - ctrl = (ctrl & ~E1000_TXDCTL_WTHRESH) | E1000_TXDCTL_FULL_TX_DESC_WB; - ew32(TXDCTL1, ctrl); - break; - } - - - if (hw->mac_type == e1000_82573) { - u32 gcr = er32(GCR); - gcr |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX; - ew32(GCR, gcr); - } - - /* Clear all of the statistics registers (clear on read). It is - * important that we do this after we have tried to establish link - * because the symbol error count will increment wildly if there - * is no link. - */ - e1000_clear_hw_cntrs(hw); - - /* ICH8 No-snoop bits are opposite polarity. - * Set to snoop by default after reset. */ - if (hw->mac_type == e1000_ich8lan) - e1000_set_pci_ex_no_snoop(hw, PCI_EX_82566_SNOOP_ALL); - - if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || - hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { - ctrl_ext = er32(CTRL_EXT); - /* Relaxed ordering must be disabled to avoid a parity - * error crash in a PCI slot. */ - ctrl_ext |= E1000_CTRL_EXT_RO_DIS; - ew32(CTRL_EXT, ctrl_ext); - } - - return ret_val; + u32 ctrl; + u32 i; + s32 ret_val; + u32 mta_size; + u32 ctrl_ext; + + DEBUGFUNC("e1000_init_hw"); + + /* Initialize Identification LED */ + ret_val = e1000_id_led_init(hw); + if (ret_val) { + DEBUGOUT("Error Initializing Identification LED\n"); + return ret_val; + } + + /* Set the media type and TBI compatibility */ + e1000_set_media_type(hw); + + /* Disabling VLAN filtering. */ + DEBUGOUT("Initializing the IEEE VLAN\n"); + if (hw->mac_type < e1000_82545_rev_3) + ew32(VET, 0); + e1000_clear_vfta(hw); + + /* For 82542 (rev 2.0), disable MWI and put the receiver into reset */ + if (hw->mac_type == e1000_82542_rev2_0) { + DEBUGOUT("Disabling MWI on 82542 rev 2.0\n"); + e1000_pci_clear_mwi(hw); + ew32(RCTL, E1000_RCTL_RST); + E1000_WRITE_FLUSH(); + msleep(5); + } + + /* Setup the receive address. This involves initializing all of the Receive + * Address Registers (RARs 0 - 15). + */ + e1000_init_rx_addrs(hw); + + /* For 82542 (rev 2.0), take the receiver out of reset and enable MWI */ + if (hw->mac_type == e1000_82542_rev2_0) { + ew32(RCTL, 0); + E1000_WRITE_FLUSH(); + msleep(1); + if (hw->pci_cmd_word & PCI_COMMAND_INVALIDATE) + e1000_pci_set_mwi(hw); + } + + /* Zero out the Multicast HASH table */ + DEBUGOUT("Zeroing the MTA\n"); + mta_size = E1000_MC_TBL_SIZE; + for (i = 0; i < mta_size; i++) { + E1000_WRITE_REG_ARRAY(hw, MTA, i, 0); + /* use write flush to prevent Memory Write Block (MWB) from + * occurring when accessing our register space */ + E1000_WRITE_FLUSH(); + } + + /* Set the PCI priority bit correctly in the CTRL register. This + * determines if the adapter gives priority to receives, or if it + * gives equal priority to transmits and receives. Valid only on + * 82542 and 82543 silicon. + */ + if (hw->dma_fairness && hw->mac_type <= e1000_82543) { + ctrl = er32(CTRL); + ew32(CTRL, ctrl | E1000_CTRL_PRIOR); + } + + switch (hw->mac_type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + break; + default: + /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */ + if (hw->bus_type == e1000_bus_type_pcix + && e1000_pcix_get_mmrbc(hw) > 2048) + e1000_pcix_set_mmrbc(hw, 2048); + break; + } + + /* Call a subroutine to configure the link and setup flow control. */ + ret_val = e1000_setup_link(hw); + + /* Set the transmit descriptor write-back policy */ + if (hw->mac_type > e1000_82544) { + ctrl = er32(TXDCTL); + ctrl = + (ctrl & ~E1000_TXDCTL_WTHRESH) | + E1000_TXDCTL_FULL_TX_DESC_WB; + ew32(TXDCTL, ctrl); + } + + /* Clear all of the statistics registers (clear on read). It is + * important that we do this after we have tried to establish link + * because the symbol error count will increment wildly if there + * is no link. + */ + e1000_clear_hw_cntrs(hw); + + if (hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER || + hw->device_id == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3) { + ctrl_ext = er32(CTRL_EXT); + /* Relaxed ordering must be disabled to avoid a parity + * error crash in a PCI slot. */ + ctrl_ext |= E1000_CTRL_EXT_RO_DIS; + ew32(CTRL_EXT, ctrl_ext); + } + + return ret_val; } -/****************************************************************************** - * Adjust SERDES output amplitude based on EEPROM setting. - * - * hw - Struct containing variables accessed by shared code. - *****************************************************************************/ +/** + * e1000_adjust_serdes_amplitude - Adjust SERDES output amplitude based on EEPROM setting. + * @hw: Struct containing variables accessed by shared code. + */ static s32 e1000_adjust_serdes_amplitude(struct e1000_hw *hw) { - u16 eeprom_data; - s32 ret_val; - - DEBUGFUNC("e1000_adjust_serdes_amplitude"); - - if (hw->media_type != e1000_media_type_internal_serdes) - return E1000_SUCCESS; - - switch (hw->mac_type) { - case e1000_82545_rev_3: - case e1000_82546_rev_3: - break; - default: - return E1000_SUCCESS; - } - - ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1, &eeprom_data); - if (ret_val) { - return ret_val; - } - - if (eeprom_data != EEPROM_RESERVED_WORD) { - /* Adjust SERDES output amplitude only. */ - eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; + u16 eeprom_data; + s32 ret_val; + + DEBUGFUNC("e1000_adjust_serdes_amplitude"); + + if (hw->media_type != e1000_media_type_internal_serdes) + return E1000_SUCCESS; + + switch (hw->mac_type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + break; + default: + return E1000_SUCCESS; + } + + ret_val = e1000_read_eeprom(hw, EEPROM_SERDES_AMPLITUDE, 1, + &eeprom_data); + if (ret_val) { + return ret_val; + } + + if (eeprom_data != EEPROM_RESERVED_WORD) { + /* Adjust SERDES output amplitude only. */ + eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK; + ret_val = + e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; } -/****************************************************************************** - * Configures flow control and link settings. - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_setup_link - Configures flow control and link settings. + * @hw: Struct containing variables accessed by shared code * - * Determines which flow control settings to use. Calls the apropriate media- + * Determines which flow control settings to use. Calls the appropriate media- * specific link configuration function. Configures the flow control settings. * Assuming the adapter has a valid link partner, a valid link should be * established. Assumes the hardware has previously been reset and the * transmitter and receiver are not enabled. - *****************************************************************************/ + */ s32 e1000_setup_link(struct e1000_hw *hw) { - u32 ctrl_ext; - s32 ret_val; - u16 eeprom_data; - - DEBUGFUNC("e1000_setup_link"); - - /* In the case of the phy reset being blocked, we already have a link. - * We do not have to set it up again. */ - if (e1000_check_phy_reset_block(hw)) - return E1000_SUCCESS; - - /* Read and store word 0x0F of the EEPROM. This word contains bits - * that determine the hardware's default PAUSE (flow control) mode, - * a bit that determines whether the HW defaults to enabling or - * disabling auto-negotiation, and the direction of the - * SW defined pins. If there is no SW over-ride of the flow - * control setting, then the variable hw->fc will - * be initialized based on a value in the EEPROM. - */ - if (hw->fc == E1000_FC_DEFAULT) { - switch (hw->mac_type) { - case e1000_ich8lan: - case e1000_82573: - hw->fc = E1000_FC_FULL; - break; - default: - ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, - 1, &eeprom_data); - if (ret_val) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) - hw->fc = E1000_FC_NONE; - else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == - EEPROM_WORD0F_ASM_DIR) - hw->fc = E1000_FC_TX_PAUSE; - else - hw->fc = E1000_FC_FULL; - break; - } - } - - /* We want to save off the original Flow Control configuration just - * in case we get disconnected and then reconnected into a different - * hub or switch with different Flow Control capabilities. - */ - if (hw->mac_type == e1000_82542_rev2_0) - hw->fc &= (~E1000_FC_TX_PAUSE); - - if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1)) - hw->fc &= (~E1000_FC_RX_PAUSE); - - hw->original_fc = hw->fc; - - DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc); - - /* Take the 4 bits from EEPROM word 0x0F that determine the initial - * polarity value for the SW controlled pins, and setup the - * Extended Device Control reg with that info. - * This is needed because one of the SW controlled pins is used for - * signal detection. So this should be done before e1000_setup_pcs_link() - * or e1000_phy_setup() is called. - */ - if (hw->mac_type == e1000_82543) { - ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, - 1, &eeprom_data); - if (ret_val) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << - SWDPIO__EXT_SHIFT); - ew32(CTRL_EXT, ctrl_ext); - } - - /* Call the necessary subroutine to configure the link. */ - ret_val = (hw->media_type == e1000_media_type_copper) ? - e1000_setup_copper_link(hw) : - e1000_setup_fiber_serdes_link(hw); - - /* Initialize the flow control address, type, and PAUSE timer - * registers to their default values. This is done even if flow - * control is disabled, because it does not hurt anything to - * initialize these registers. - */ - DEBUGOUT("Initializing the Flow Control address, type and timer regs\n"); - - /* FCAL/H and FCT are hardcoded to standard values in e1000_ich8lan. */ - if (hw->mac_type != e1000_ich8lan) { - ew32(FCT, FLOW_CONTROL_TYPE); - ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH); - ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW); - } - - ew32(FCTTV, hw->fc_pause_time); - - /* Set the flow control receive threshold registers. Normally, - * these registers will be set to a default threshold that may be - * adjusted later by the driver's runtime code. However, if the - * ability to transmit pause frames in not enabled, then these - * registers will be set to 0. - */ - if (!(hw->fc & E1000_FC_TX_PAUSE)) { - ew32(FCRTL, 0); - ew32(FCRTH, 0); - } else { - /* We need to set up the Receive Threshold high and low water marks - * as well as (optionally) enabling the transmission of XON frames. - */ - if (hw->fc_send_xon) { - ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE)); - ew32(FCRTH, hw->fc_high_water); - } else { - ew32(FCRTL, hw->fc_low_water); - ew32(FCRTH, hw->fc_high_water); - } - } - return ret_val; + u32 ctrl_ext; + s32 ret_val; + u16 eeprom_data; + + DEBUGFUNC("e1000_setup_link"); + + /* Read and store word 0x0F of the EEPROM. This word contains bits + * that determine the hardware's default PAUSE (flow control) mode, + * a bit that determines whether the HW defaults to enabling or + * disabling auto-negotiation, and the direction of the + * SW defined pins. If there is no SW over-ride of the flow + * control setting, then the variable hw->fc will + * be initialized based on a value in the EEPROM. + */ + if (hw->fc == E1000_FC_DEFAULT) { + ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, + 1, &eeprom_data); + if (ret_val) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == 0) + hw->fc = E1000_FC_NONE; + else if ((eeprom_data & EEPROM_WORD0F_PAUSE_MASK) == + EEPROM_WORD0F_ASM_DIR) + hw->fc = E1000_FC_TX_PAUSE; + else + hw->fc = E1000_FC_FULL; + } + + /* We want to save off the original Flow Control configuration just + * in case we get disconnected and then reconnected into a different + * hub or switch with different Flow Control capabilities. + */ + if (hw->mac_type == e1000_82542_rev2_0) + hw->fc &= (~E1000_FC_TX_PAUSE); + + if ((hw->mac_type < e1000_82543) && (hw->report_tx_early == 1)) + hw->fc &= (~E1000_FC_RX_PAUSE); + + hw->original_fc = hw->fc; + + DEBUGOUT1("After fix-ups FlowControl is now = %x\n", hw->fc); + + /* Take the 4 bits from EEPROM word 0x0F that determine the initial + * polarity value for the SW controlled pins, and setup the + * Extended Device Control reg with that info. + * This is needed because one of the SW controlled pins is used for + * signal detection. So this should be done before e1000_setup_pcs_link() + * or e1000_phy_setup() is called. + */ + if (hw->mac_type == e1000_82543) { + ret_val = e1000_read_eeprom(hw, EEPROM_INIT_CONTROL2_REG, + 1, &eeprom_data); + if (ret_val) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + ctrl_ext = ((eeprom_data & EEPROM_WORD0F_SWPDIO_EXT) << + SWDPIO__EXT_SHIFT); + ew32(CTRL_EXT, ctrl_ext); + } + + /* Call the necessary subroutine to configure the link. */ + ret_val = (hw->media_type == e1000_media_type_copper) ? + e1000_setup_copper_link(hw) : e1000_setup_fiber_serdes_link(hw); + + /* Initialize the flow control address, type, and PAUSE timer + * registers to their default values. This is done even if flow + * control is disabled, because it does not hurt anything to + * initialize these registers. + */ + DEBUGOUT + ("Initializing the Flow Control address, type and timer regs\n"); + + ew32(FCT, FLOW_CONTROL_TYPE); + ew32(FCAH, FLOW_CONTROL_ADDRESS_HIGH); + ew32(FCAL, FLOW_CONTROL_ADDRESS_LOW); + + ew32(FCTTV, hw->fc_pause_time); + + /* Set the flow control receive threshold registers. Normally, + * these registers will be set to a default threshold that may be + * adjusted later by the driver's runtime code. However, if the + * ability to transmit pause frames in not enabled, then these + * registers will be set to 0. + */ + if (!(hw->fc & E1000_FC_TX_PAUSE)) { + ew32(FCRTL, 0); + ew32(FCRTH, 0); + } else { + /* We need to set up the Receive Threshold high and low water marks + * as well as (optionally) enabling the transmission of XON frames. + */ + if (hw->fc_send_xon) { + ew32(FCRTL, (hw->fc_low_water | E1000_FCRTL_XONE)); + ew32(FCRTH, hw->fc_high_water); + } else { + ew32(FCRTL, hw->fc_low_water); + ew32(FCRTH, hw->fc_high_water); + } + } + return ret_val; } -/****************************************************************************** - * Sets up link for a fiber based or serdes based adapter - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_setup_fiber_serdes_link - prepare fiber or serdes link + * @hw: Struct containing variables accessed by shared code * * Manipulates Physical Coding Sublayer functions in order to configure * link. Assumes the hardware has been previously reset and the transmitter * and receiver are not enabled. - *****************************************************************************/ + */ static s32 e1000_setup_fiber_serdes_link(struct e1000_hw *hw) { - u32 ctrl; - u32 status; - u32 txcw = 0; - u32 i; - u32 signal = 0; - s32 ret_val; - - DEBUGFUNC("e1000_setup_fiber_serdes_link"); - - /* On 82571 and 82572 Fiber connections, SerDes loopback mode persists - * until explicitly turned off or a power cycle is performed. A read to - * the register does not indicate its status. Therefore, we ensure - * loopback mode is disabled during initialization. - */ - if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) - ew32(SCTL, E1000_DISABLE_SERDES_LOOPBACK); - - /* On adapters with a MAC newer than 82544, SWDP 1 will be - * set when the optics detect a signal. On older adapters, it will be - * cleared when there is a signal. This applies to fiber media only. - * If we're on serdes media, adjust the output amplitude to value - * set in the EEPROM. - */ - ctrl = er32(CTRL); - if (hw->media_type == e1000_media_type_fiber) - signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0; - - ret_val = e1000_adjust_serdes_amplitude(hw); - if (ret_val) - return ret_val; - - /* Take the link out of reset */ - ctrl &= ~(E1000_CTRL_LRST); - - /* Adjust VCO speed to improve BER performance */ - ret_val = e1000_set_vco_speed(hw); - if (ret_val) - return ret_val; - - e1000_config_collision_dist(hw); - - /* Check for a software override of the flow control settings, and setup - * the device accordingly. If auto-negotiation is enabled, then software - * will have to set the "PAUSE" bits to the correct value in the Tranmsit - * Config Word Register (TXCW) and re-start auto-negotiation. However, if - * auto-negotiation is disabled, then software will have to manually - * configure the two flow control enable bits in the CTRL register. - * - * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames, but - * not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames but we do - * not support receiving pause frames). - * 3: Both Rx and TX flow control (symmetric) are enabled. - */ - switch (hw->fc) { - case E1000_FC_NONE: - /* Flow control is completely disabled by a software over-ride. */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); - break; - case E1000_FC_RX_PAUSE: - /* RX Flow control is enabled and TX Flow control is disabled by a - * software over-ride. Since there really isn't a way to advertise - * that we are capable of RX Pause ONLY, we will advertise that we - * support both symmetric and asymmetric RX PAUSE. Later, we will - * disable the adapter's ability to send PAUSE frames. - */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); - break; - case E1000_FC_TX_PAUSE: - /* TX Flow control is enabled, and RX Flow control is disabled, by a - * software over-ride. - */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); - break; - case E1000_FC_FULL: - /* Flow control (both RX and TX) is enabled by a software over-ride. */ - txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); - break; - default: - DEBUGOUT("Flow control param set incorrectly\n"); - return -E1000_ERR_CONFIG; - break; - } - - /* Since auto-negotiation is enabled, take the link out of reset (the link - * will be in reset, because we previously reset the chip). This will - * restart auto-negotiation. If auto-neogtiation is successful then the - * link-up status bit will be set and the flow control enable bits (RFCE - * and TFCE) will be set according to their negotiated value. - */ - DEBUGOUT("Auto-negotiation enabled\n"); - - ew32(TXCW, txcw); - ew32(CTRL, ctrl); - E1000_WRITE_FLUSH(); - - hw->txcw = txcw; - msleep(1); - - /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" - * indication in the Device Status Register. Time-out if a link isn't - * seen in 500 milliseconds seconds (Auto-negotiation should complete in - * less than 500 milliseconds even if the other end is doing it in SW). - * For internal serdes, we just assume a signal is present, then poll. - */ - if (hw->media_type == e1000_media_type_internal_serdes || - (er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) { - DEBUGOUT("Looking for Link\n"); - for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) { - msleep(10); - status = er32(STATUS); - if (status & E1000_STATUS_LU) break; - } - if (i == (LINK_UP_TIMEOUT / 10)) { - DEBUGOUT("Never got a valid link from auto-neg!!!\n"); - hw->autoneg_failed = 1; - /* AutoNeg failed to achieve a link, so we'll call - * e1000_check_for_link. This routine will force the link up if - * we detect a signal. This will allow us to communicate with - * non-autonegotiating link partners. - */ - ret_val = e1000_check_for_link(hw); - if (ret_val) { - DEBUGOUT("Error while checking for link\n"); - return ret_val; - } - hw->autoneg_failed = 0; - } else { - hw->autoneg_failed = 0; - DEBUGOUT("Valid Link Found\n"); - } - } else { - DEBUGOUT("No Signal Detected\n"); - } - return E1000_SUCCESS; + u32 ctrl; + u32 status; + u32 txcw = 0; + u32 i; + u32 signal = 0; + s32 ret_val; + + DEBUGFUNC("e1000_setup_fiber_serdes_link"); + + /* On adapters with a MAC newer than 82544, SWDP 1 will be + * set when the optics detect a signal. On older adapters, it will be + * cleared when there is a signal. This applies to fiber media only. + * If we're on serdes media, adjust the output amplitude to value + * set in the EEPROM. + */ + ctrl = er32(CTRL); + if (hw->media_type == e1000_media_type_fiber) + signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0; + + ret_val = e1000_adjust_serdes_amplitude(hw); + if (ret_val) + return ret_val; + + /* Take the link out of reset */ + ctrl &= ~(E1000_CTRL_LRST); + + /* Adjust VCO speed to improve BER performance */ + ret_val = e1000_set_vco_speed(hw); + if (ret_val) + return ret_val; + + e1000_config_collision_dist(hw); + + /* Check for a software override of the flow control settings, and setup + * the device accordingly. If auto-negotiation is enabled, then software + * will have to set the "PAUSE" bits to the correct value in the Tranmsit + * Config Word Register (TXCW) and re-start auto-negotiation. However, if + * auto-negotiation is disabled, then software will have to manually + * configure the two flow control enable bits in the CTRL register. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames, but + * not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames but we do + * not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. + */ + switch (hw->fc) { + case E1000_FC_NONE: + /* Flow control is completely disabled by a software over-ride. */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD); + break; + case E1000_FC_RX_PAUSE: + /* RX Flow control is enabled and TX Flow control is disabled by a + * software over-ride. Since there really isn't a way to advertise + * that we are capable of RX Pause ONLY, we will advertise that we + * support both symmetric and asymmetric RX PAUSE. Later, we will + * disable the adapter's ability to send PAUSE frames. + */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); + break; + case E1000_FC_TX_PAUSE: + /* TX Flow control is enabled, and RX Flow control is disabled, by a + * software over-ride. + */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_ASM_DIR); + break; + case E1000_FC_FULL: + /* Flow control (both RX and TX) is enabled by a software over-ride. */ + txcw = (E1000_TXCW_ANE | E1000_TXCW_FD | E1000_TXCW_PAUSE_MASK); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + return -E1000_ERR_CONFIG; + break; + } + + /* Since auto-negotiation is enabled, take the link out of reset (the link + * will be in reset, because we previously reset the chip). This will + * restart auto-negotiation. If auto-negotiation is successful then the + * link-up status bit will be set and the flow control enable bits (RFCE + * and TFCE) will be set according to their negotiated value. + */ + DEBUGOUT("Auto-negotiation enabled\n"); + + ew32(TXCW, txcw); + ew32(CTRL, ctrl); + E1000_WRITE_FLUSH(); + + hw->txcw = txcw; + msleep(1); + + /* If we have a signal (the cable is plugged in) then poll for a "Link-Up" + * indication in the Device Status Register. Time-out if a link isn't + * seen in 500 milliseconds seconds (Auto-negotiation should complete in + * less than 500 milliseconds even if the other end is doing it in SW). + * For internal serdes, we just assume a signal is present, then poll. + */ + if (hw->media_type == e1000_media_type_internal_serdes || + (er32(CTRL) & E1000_CTRL_SWDPIN1) == signal) { + DEBUGOUT("Looking for Link\n"); + for (i = 0; i < (LINK_UP_TIMEOUT / 10); i++) { + msleep(10); + status = er32(STATUS); + if (status & E1000_STATUS_LU) + break; + } + if (i == (LINK_UP_TIMEOUT / 10)) { + DEBUGOUT("Never got a valid link from auto-neg!!!\n"); + hw->autoneg_failed = 1; + /* AutoNeg failed to achieve a link, so we'll call + * e1000_check_for_link. This routine will force the link up if + * we detect a signal. This will allow us to communicate with + * non-autonegotiating link partners. + */ + ret_val = e1000_check_for_link(hw); + if (ret_val) { + DEBUGOUT("Error while checking for link\n"); + return ret_val; + } + hw->autoneg_failed = 0; + } else { + hw->autoneg_failed = 0; + DEBUGOUT("Valid Link Found\n"); + } + } else { + DEBUGOUT("No Signal Detected\n"); + } + return E1000_SUCCESS; } -/****************************************************************************** -* Make sure we have a valid PHY and change PHY mode before link setup. -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ +/** + * e1000_copper_link_preconfig - early configuration for copper + * @hw: Struct containing variables accessed by shared code + * + * Make sure we have a valid PHY and change PHY mode before link setup. + */ static s32 e1000_copper_link_preconfig(struct e1000_hw *hw) { - u32 ctrl; - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_copper_link_preconfig"); - - ctrl = er32(CTRL); - /* With 82543, we need to force speed and duplex on the MAC equal to what - * the PHY speed and duplex configuration is. In addition, we need to - * perform a hardware reset on the PHY to take it out of reset. - */ - if (hw->mac_type > e1000_82543) { - ctrl |= E1000_CTRL_SLU; - ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); - ew32(CTRL, ctrl); - } else { - ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU); - ew32(CTRL, ctrl); - ret_val = e1000_phy_hw_reset(hw); - if (ret_val) - return ret_val; - } - - /* Make sure we have a valid PHY */ - ret_val = e1000_detect_gig_phy(hw); - if (ret_val) { - DEBUGOUT("Error, did not detect valid phy.\n"); - return ret_val; - } - DEBUGOUT1("Phy ID = %x \n", hw->phy_id); - - /* Set PHY to class A mode (if necessary) */ - ret_val = e1000_set_phy_mode(hw); - if (ret_val) - return ret_val; - - if ((hw->mac_type == e1000_82545_rev_3) || - (hw->mac_type == e1000_82546_rev_3)) { - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - phy_data |= 0x00000008; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - } - - if (hw->mac_type <= e1000_82543 || - hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 || - hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) - hw->phy_reset_disable = false; - - return E1000_SUCCESS; -} + u32 ctrl; + s32 ret_val; + u16 phy_data; + DEBUGFUNC("e1000_copper_link_preconfig"); -/******************************************************************** -* Copper link setup for e1000_phy_igp series. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ -static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw) -{ - u32 led_ctrl; - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_copper_link_igp_setup"); - - if (hw->phy_reset_disable) - return E1000_SUCCESS; - - ret_val = e1000_phy_reset(hw); - if (ret_val) { - DEBUGOUT("Error Resetting the PHY\n"); - return ret_val; - } - - /* Wait 15ms for MAC to configure PHY from eeprom settings */ - msleep(15); - if (hw->mac_type != e1000_ich8lan) { - /* Configure activity LED after PHY reset */ - led_ctrl = er32(LEDCTL); - led_ctrl &= IGP_ACTIVITY_LED_MASK; - led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); - ew32(LEDCTL, led_ctrl); - } - - /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */ - if (hw->phy_type == e1000_phy_igp) { - /* disable lplu d3 during driver init */ - ret_val = e1000_set_d3_lplu_state(hw, false); - if (ret_val) { - DEBUGOUT("Error Disabling LPLU D3\n"); - return ret_val; - } - } - - /* disable lplu d0 during driver init */ - ret_val = e1000_set_d0_lplu_state(hw, false); - if (ret_val) { - DEBUGOUT("Error Disabling LPLU D0\n"); - return ret_val; - } - /* Configure mdi-mdix settings */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); - if (ret_val) - return ret_val; - - if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { - hw->dsp_config_state = e1000_dsp_config_disabled; - /* Force MDI for earlier revs of the IGP PHY */ - phy_data &= ~(IGP01E1000_PSCR_AUTO_MDIX | IGP01E1000_PSCR_FORCE_MDI_MDIX); - hw->mdix = 1; - - } else { - hw->dsp_config_state = e1000_dsp_config_enabled; - phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; - - switch (hw->mdix) { - case 1: - phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; - break; - case 2: - phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; - break; - case 0: - default: - phy_data |= IGP01E1000_PSCR_AUTO_MDIX; - break; - } - } - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); - if (ret_val) - return ret_val; - - /* set auto-master slave resolution settings */ - if (hw->autoneg) { - e1000_ms_type phy_ms_setting = hw->master_slave; - - if (hw->ffe_config_state == e1000_ffe_config_active) - hw->ffe_config_state = e1000_ffe_config_enabled; - - if (hw->dsp_config_state == e1000_dsp_config_activated) - hw->dsp_config_state = e1000_dsp_config_enabled; - - /* when autonegotiation advertisment is only 1000Mbps then we - * should disable SmartSpeed and enable Auto MasterSlave - * resolution as hardware default. */ - if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { - /* Disable SmartSpeed */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - /* Set auto Master/Slave resolution process */ - ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); - if (ret_val) - return ret_val; - phy_data &= ~CR_1000T_MS_ENABLE; - ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); - if (ret_val) - return ret_val; - } - - ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); - if (ret_val) - return ret_val; - - /* load defaults for future use */ - hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ? - ((phy_data & CR_1000T_MS_VALUE) ? - e1000_ms_force_master : - e1000_ms_force_slave) : - e1000_ms_auto; - - switch (phy_ms_setting) { - case e1000_ms_force_master: - phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); - break; - case e1000_ms_force_slave: - phy_data |= CR_1000T_MS_ENABLE; - phy_data &= ~(CR_1000T_MS_VALUE); - break; - case e1000_ms_auto: - phy_data &= ~CR_1000T_MS_ENABLE; - default: - break; - } - ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; + ctrl = er32(CTRL); + /* With 82543, we need to force speed and duplex on the MAC equal to what + * the PHY speed and duplex configuration is. In addition, we need to + * perform a hardware reset on the PHY to take it out of reset. + */ + if (hw->mac_type > e1000_82543) { + ctrl |= E1000_CTRL_SLU; + ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ew32(CTRL, ctrl); + } else { + ctrl |= + (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU); + ew32(CTRL, ctrl); + ret_val = e1000_phy_hw_reset(hw); + if (ret_val) + return ret_val; + } + + /* Make sure we have a valid PHY */ + ret_val = e1000_detect_gig_phy(hw); + if (ret_val) { + DEBUGOUT("Error, did not detect valid phy.\n"); + return ret_val; + } + DEBUGOUT1("Phy ID = %x \n", hw->phy_id); + + /* Set PHY to class A mode (if necessary) */ + ret_val = e1000_set_phy_mode(hw); + if (ret_val) + return ret_val; + + if ((hw->mac_type == e1000_82545_rev_3) || + (hw->mac_type == e1000_82546_rev_3)) { + ret_val = + e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + phy_data |= 0x00000008; + ret_val = + e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + } + + if (hw->mac_type <= e1000_82543 || + hw->mac_type == e1000_82541 || hw->mac_type == e1000_82547 || + hw->mac_type == e1000_82541_rev_2 + || hw->mac_type == e1000_82547_rev_2) + hw->phy_reset_disable = false; + + return E1000_SUCCESS; } -/******************************************************************** -* Copper link setup for e1000_phy_gg82563 series. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ -static s32 e1000_copper_link_ggp_setup(struct e1000_hw *hw) +/** + * e1000_copper_link_igp_setup - Copper link setup for e1000_phy_igp series. + * @hw: Struct containing variables accessed by shared code + */ +static s32 e1000_copper_link_igp_setup(struct e1000_hw *hw) { - s32 ret_val; - u16 phy_data; - u32 reg_data; - - DEBUGFUNC("e1000_copper_link_ggp_setup"); - - if (!hw->phy_reset_disable) { - - /* Enable CRS on TX for half-duplex operation. */ - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, - &phy_data); - if (ret_val) - return ret_val; - - phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; - /* Use 25MHz for both link down and 1000BASE-T for Tx clock */ - phy_data |= GG82563_MSCR_TX_CLK_1000MBPS_25MHZ; - - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, - phy_data); - if (ret_val) - return ret_val; - - /* Options: - * MDI/MDI-X = 0 (default) - * 0 - Auto for all speeds - * 1 - MDI mode - * 2 - MDI-X mode - * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) - */ - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_PSCR_CROSSOVER_MODE_MASK; - - switch (hw->mdix) { - case 1: - phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDI; - break; - case 2: - phy_data |= GG82563_PSCR_CROSSOVER_MODE_MDIX; - break; - case 0: - default: - phy_data |= GG82563_PSCR_CROSSOVER_MODE_AUTO; - break; - } - - /* Options: - * disable_polarity_correction = 0 (default) - * Automatic Correction for Reversed Cable Polarity - * 0 - Disabled - * 1 - Enabled - */ - phy_data &= ~GG82563_PSCR_POLARITY_REVERSAL_DISABLE; - if (hw->disable_polarity_correction == 1) - phy_data |= GG82563_PSCR_POLARITY_REVERSAL_DISABLE; - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL, phy_data); - - if (ret_val) - return ret_val; - - /* SW Reset the PHY so all changes take effect */ - ret_val = e1000_phy_reset(hw); - if (ret_val) { - DEBUGOUT("Error Resetting the PHY\n"); - return ret_val; - } - } /* phy_reset_disable */ - - if (hw->mac_type == e1000_80003es2lan) { - /* Bypass RX and TX FIFO's */ - ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_FIFO_CTRL, - E1000_KUMCTRLSTA_FIFO_CTRL_RX_BYPASS | - E1000_KUMCTRLSTA_FIFO_CTRL_TX_BYPASS); - if (ret_val) - return ret_val; - - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_PSCR2_REVERSE_AUTO_NEG; - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_SPEC_CTRL_2, phy_data); - - if (ret_val) - return ret_val; - - reg_data = er32(CTRL_EXT); - reg_data &= ~(E1000_CTRL_EXT_LINK_MODE_MASK); - ew32(CTRL_EXT, reg_data); - - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, - &phy_data); - if (ret_val) - return ret_val; - - /* Do not init these registers when the HW is in IAMT mode, since the - * firmware will have already initialized them. We only initialize - * them if the HW is not in IAMT mode. - */ - if (!e1000_check_mng_mode(hw)) { - /* Enable Electrical Idle on the PHY */ - phy_data |= GG82563_PMCR_ENABLE_ELECTRICAL_IDLE; - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_PWR_MGMT_CTRL, - phy_data); - if (ret_val) - return ret_val; - - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, - phy_data); - - if (ret_val) - return ret_val; - } - - /* Workaround: Disable padding in Kumeran interface in the MAC - * and in the PHY to avoid CRC errors. - */ - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_INBAND_CTRL, - &phy_data); - if (ret_val) - return ret_val; - phy_data |= GG82563_ICR_DIS_PADDING; - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_INBAND_CTRL, - phy_data); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; + u32 led_ctrl; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_copper_link_igp_setup"); + + if (hw->phy_reset_disable) + return E1000_SUCCESS; + + ret_val = e1000_phy_reset(hw); + if (ret_val) { + DEBUGOUT("Error Resetting the PHY\n"); + return ret_val; + } + + /* Wait 15ms for MAC to configure PHY from eeprom settings */ + msleep(15); + /* Configure activity LED after PHY reset */ + led_ctrl = er32(LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + ew32(LEDCTL, led_ctrl); + + /* The NVM settings will configure LPLU in D3 for IGP2 and IGP3 PHYs */ + if (hw->phy_type == e1000_phy_igp) { + /* disable lplu d3 during driver init */ + ret_val = e1000_set_d3_lplu_state(hw, false); + if (ret_val) { + DEBUGOUT("Error Disabling LPLU D3\n"); + return ret_val; + } + } + + /* Configure mdi-mdix settings */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); + if (ret_val) + return ret_val; + + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + hw->dsp_config_state = e1000_dsp_config_disabled; + /* Force MDI for earlier revs of the IGP PHY */ + phy_data &= + ~(IGP01E1000_PSCR_AUTO_MDIX | + IGP01E1000_PSCR_FORCE_MDI_MDIX); + hw->mdix = 1; + + } else { + hw->dsp_config_state = e1000_dsp_config_enabled; + phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; + + switch (hw->mdix) { + case 1: + phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 2: + phy_data |= IGP01E1000_PSCR_FORCE_MDI_MDIX; + break; + case 0: + default: + phy_data |= IGP01E1000_PSCR_AUTO_MDIX; + break; + } + } + ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); + if (ret_val) + return ret_val; + + /* set auto-master slave resolution settings */ + if (hw->autoneg) { + e1000_ms_type phy_ms_setting = hw->master_slave; + + if (hw->ffe_config_state == e1000_ffe_config_active) + hw->ffe_config_state = e1000_ffe_config_enabled; + + if (hw->dsp_config_state == e1000_dsp_config_activated) + hw->dsp_config_state = e1000_dsp_config_enabled; + + /* when autonegotiation advertisement is only 1000Mbps then we + * should disable SmartSpeed and enable Auto MasterSlave + * resolution as hardware default. */ + if (hw->autoneg_advertised == ADVERTISE_1000_FULL) { + /* Disable SmartSpeed */ + ret_val = + e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + /* Set auto Master/Slave resolution process */ + ret_val = + e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); + if (ret_val) + return ret_val; + phy_data &= ~CR_1000T_MS_ENABLE; + ret_val = + e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); + if (ret_val) + return ret_val; + } + + ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &phy_data); + if (ret_val) + return ret_val; + + /* load defaults for future use */ + hw->original_master_slave = (phy_data & CR_1000T_MS_ENABLE) ? + ((phy_data & CR_1000T_MS_VALUE) ? + e1000_ms_force_master : + e1000_ms_force_slave) : e1000_ms_auto; + + switch (phy_ms_setting) { + case e1000_ms_force_master: + phy_data |= (CR_1000T_MS_ENABLE | CR_1000T_MS_VALUE); + break; + case e1000_ms_force_slave: + phy_data |= CR_1000T_MS_ENABLE; + phy_data &= ~(CR_1000T_MS_VALUE); + break; + case e1000_ms_auto: + phy_data &= ~CR_1000T_MS_ENABLE; + default: + break; + } + ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, phy_data); + if (ret_val) + return ret_val; + } + + return E1000_SUCCESS; } -/******************************************************************** -* Copper link setup for e1000_phy_m88 series. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ +/** + * e1000_copper_link_mgp_setup - Copper link setup for e1000_phy_m88 series. + * @hw: Struct containing variables accessed by shared code + */ static s32 e1000_copper_link_mgp_setup(struct e1000_hw *hw) { - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_copper_link_mgp_setup"); - - if (hw->phy_reset_disable) - return E1000_SUCCESS; - - /* Enable CRS on TX. This must be set for half-duplex operation. */ - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; - - /* Options: - * MDI/MDI-X = 0 (default) - * 0 - Auto for all speeds - * 1 - MDI mode - * 2 - MDI-X mode - * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) - */ - phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; - - switch (hw->mdix) { - case 1: - phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; - break; - case 2: - phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; - break; - case 3: - phy_data |= M88E1000_PSCR_AUTO_X_1000T; - break; - case 0: - default: - phy_data |= M88E1000_PSCR_AUTO_X_MODE; - break; - } - - /* Options: - * disable_polarity_correction = 0 (default) - * Automatic Correction for Reversed Cable Polarity - * 0 - Disabled - * 1 - Enabled - */ - phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; - if (hw->disable_polarity_correction == 1) - phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - if (hw->phy_revision < M88E1011_I_REV_4) { - /* Force TX_CLK in the Extended PHY Specific Control Register - * to 25MHz clock. - */ - ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_EPSCR_TX_CLK_25; - - if ((hw->phy_revision == E1000_REVISION_2) && - (hw->phy_id == M88E1111_I_PHY_ID)) { - /* Vidalia Phy, set the downshift counter to 5x */ - phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); - phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; - ret_val = e1000_write_phy_reg(hw, - M88E1000_EXT_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - } else { - /* Configure Master and Slave downshift values */ - phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | - M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); - phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | - M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); - ret_val = e1000_write_phy_reg(hw, - M88E1000_EXT_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - } - } - - /* SW Reset the PHY so all changes take effect */ - ret_val = e1000_phy_reset(hw); - if (ret_val) { - DEBUGOUT("Error Resetting the PHY\n"); - return ret_val; - } - - return E1000_SUCCESS; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_copper_link_mgp_setup"); + + if (hw->phy_reset_disable) + return E1000_SUCCESS; + + /* Enable CRS on TX. This must be set for half-duplex operation. */ + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + + /* Options: + * MDI/MDI-X = 0 (default) + * 0 - Auto for all speeds + * 1 - MDI mode + * 2 - MDI-X mode + * 3 - Auto for 1000Base-T only (MDI-X for 10/100Base-T modes) + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + + switch (hw->mdix) { + case 1: + phy_data |= M88E1000_PSCR_MDI_MANUAL_MODE; + break; + case 2: + phy_data |= M88E1000_PSCR_MDIX_MANUAL_MODE; + break; + case 3: + phy_data |= M88E1000_PSCR_AUTO_X_1000T; + break; + case 0: + default: + phy_data |= M88E1000_PSCR_AUTO_X_MODE; + break; + } + + /* Options: + * disable_polarity_correction = 0 (default) + * Automatic Correction for Reversed Cable Polarity + * 0 - Disabled + * 1 - Enabled + */ + phy_data &= ~M88E1000_PSCR_POLARITY_REVERSAL; + if (hw->disable_polarity_correction == 1) + phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + + if (hw->phy_revision < M88E1011_I_REV_4) { + /* Force TX_CLK in the Extended PHY Specific Control Register + * to 25MHz clock. + */ + ret_val = + e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, + &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_EPSCR_TX_CLK_25; + + if ((hw->phy_revision == E1000_REVISION_2) && + (hw->phy_id == M88E1111_I_PHY_ID)) { + /* Vidalia Phy, set the downshift counter to 5x */ + phy_data &= ~(M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK); + phy_data |= M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X; + ret_val = e1000_write_phy_reg(hw, + M88E1000_EXT_PHY_SPEC_CTRL, + phy_data); + if (ret_val) + return ret_val; + } else { + /* Configure Master and Slave downshift values */ + phy_data &= ~(M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK); + phy_data |= (M88E1000_EPSCR_MASTER_DOWNSHIFT_1X | + M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X); + ret_val = e1000_write_phy_reg(hw, + M88E1000_EXT_PHY_SPEC_CTRL, + phy_data); + if (ret_val) + return ret_val; + } + } + + /* SW Reset the PHY so all changes take effect */ + ret_val = e1000_phy_reset(hw); + if (ret_val) { + DEBUGOUT("Error Resetting the PHY\n"); + return ret_val; + } + + return E1000_SUCCESS; } -/******************************************************************** -* Setup auto-negotiation and flow control advertisements, -* and then perform auto-negotiation. -* -* hw - Struct containing variables accessed by shared code -*********************************************************************/ +/** + * e1000_copper_link_autoneg - setup auto-neg + * @hw: Struct containing variables accessed by shared code + * + * Setup auto-negotiation and flow control advertisements, + * and then perform auto-negotiation. + */ static s32 e1000_copper_link_autoneg(struct e1000_hw *hw) { - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_copper_link_autoneg"); - - /* Perform some bounds checking on the hw->autoneg_advertised - * parameter. If this variable is zero, then set it to the default. - */ - hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT; - - /* If autoneg_advertised is zero, we assume it was not defaulted - * by the calling code so we set to advertise full capability. - */ - if (hw->autoneg_advertised == 0) - hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; - - /* IFE phy only supports 10/100 */ - if (hw->phy_type == e1000_phy_ife) - hw->autoneg_advertised &= AUTONEG_ADVERTISE_10_100_ALL; - - DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); - ret_val = e1000_phy_setup_autoneg(hw); - if (ret_val) { - DEBUGOUT("Error Setting up Auto-Negotiation\n"); - return ret_val; - } - DEBUGOUT("Restarting Auto-Neg\n"); - - /* Restart auto-negotiation by setting the Auto Neg Enable bit and - * the Auto Neg Restart bit in the PHY control register. - */ - ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); - ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); - if (ret_val) - return ret_val; - - /* Does the user want to wait for Auto-Neg to complete here, or - * check at a later time (for example, callback routine). - */ - if (hw->wait_autoneg_complete) { - ret_val = e1000_wait_autoneg(hw); - if (ret_val) { - DEBUGOUT("Error while waiting for autoneg to complete\n"); - return ret_val; - } - } - - hw->get_link_status = true; - - return E1000_SUCCESS; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_copper_link_autoneg"); + + /* Perform some bounds checking on the hw->autoneg_advertised + * parameter. If this variable is zero, then set it to the default. + */ + hw->autoneg_advertised &= AUTONEG_ADVERTISE_SPEED_DEFAULT; + + /* If autoneg_advertised is zero, we assume it was not defaulted + * by the calling code so we set to advertise full capability. + */ + if (hw->autoneg_advertised == 0) + hw->autoneg_advertised = AUTONEG_ADVERTISE_SPEED_DEFAULT; + + DEBUGOUT("Reconfiguring auto-neg advertisement params\n"); + ret_val = e1000_phy_setup_autoneg(hw); + if (ret_val) { + DEBUGOUT("Error Setting up Auto-Negotiation\n"); + return ret_val; + } + DEBUGOUT("Restarting Auto-Neg\n"); + + /* Restart auto-negotiation by setting the Auto Neg Enable bit and + * the Auto Neg Restart bit in the PHY control register. + */ + ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); + ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); + if (ret_val) + return ret_val; + + /* Does the user want to wait for Auto-Neg to complete here, or + * check at a later time (for example, callback routine). + */ + if (hw->wait_autoneg_complete) { + ret_val = e1000_wait_autoneg(hw); + if (ret_val) { + DEBUGOUT + ("Error while waiting for autoneg to complete\n"); + return ret_val; + } + } + + hw->get_link_status = true; + + return E1000_SUCCESS; } -/****************************************************************************** -* Config the MAC and the PHY after link is up. -* 1) Set up the MAC to the current PHY speed/duplex -* if we are on 82543. If we -* are on newer silicon, we only need to configure -* collision distance in the Transmit Control Register. -* 2) Set up flow control on the MAC to that established with -* the link partner. -* 3) Config DSP to improve Gigabit link quality for some PHY revisions. -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ +/** + * e1000_copper_link_postconfig - post link setup + * @hw: Struct containing variables accessed by shared code + * + * Config the MAC and the PHY after link is up. + * 1) Set up the MAC to the current PHY speed/duplex + * if we are on 82543. If we + * are on newer silicon, we only need to configure + * collision distance in the Transmit Control Register. + * 2) Set up flow control on the MAC to that established with + * the link partner. + * 3) Config DSP to improve Gigabit link quality for some PHY revisions. + */ static s32 e1000_copper_link_postconfig(struct e1000_hw *hw) { - s32 ret_val; - DEBUGFUNC("e1000_copper_link_postconfig"); - - if (hw->mac_type >= e1000_82544) { - e1000_config_collision_dist(hw); - } else { - ret_val = e1000_config_mac_to_phy(hw); - if (ret_val) { - DEBUGOUT("Error configuring MAC to PHY settings\n"); - return ret_val; - } - } - ret_val = e1000_config_fc_after_link_up(hw); - if (ret_val) { - DEBUGOUT("Error Configuring Flow Control\n"); - return ret_val; - } - - /* Config DSP to improve Giga link quality */ - if (hw->phy_type == e1000_phy_igp) { - ret_val = e1000_config_dsp_after_link_change(hw, true); - if (ret_val) { - DEBUGOUT("Error Configuring DSP after link up\n"); - return ret_val; - } - } - - return E1000_SUCCESS; + s32 ret_val; + DEBUGFUNC("e1000_copper_link_postconfig"); + + if (hw->mac_type >= e1000_82544) { + e1000_config_collision_dist(hw); + } else { + ret_val = e1000_config_mac_to_phy(hw); + if (ret_val) { + DEBUGOUT("Error configuring MAC to PHY settings\n"); + return ret_val; + } + } + ret_val = e1000_config_fc_after_link_up(hw); + if (ret_val) { + DEBUGOUT("Error Configuring Flow Control\n"); + return ret_val; + } + + /* Config DSP to improve Giga link quality */ + if (hw->phy_type == e1000_phy_igp) { + ret_val = e1000_config_dsp_after_link_change(hw, true); + if (ret_val) { + DEBUGOUT("Error Configuring DSP after link up\n"); + return ret_val; + } + } + + return E1000_SUCCESS; } -/****************************************************************************** -* Detects which PHY is present and setup the speed and duplex -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ +/** + * e1000_setup_copper_link - phy/speed/duplex setting + * @hw: Struct containing variables accessed by shared code + * + * Detects which PHY is present and sets up the speed and duplex + */ static s32 e1000_setup_copper_link(struct e1000_hw *hw) { - s32 ret_val; - u16 i; - u16 phy_data; - u16 reg_data = 0; - - DEBUGFUNC("e1000_setup_copper_link"); - - switch (hw->mac_type) { - case e1000_80003es2lan: - case e1000_ich8lan: - /* Set the mac to wait the maximum time between each - * iteration and increase the max iterations when - * polling the phy; this fixes erroneous timeouts at 10Mbps. */ - ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 4), 0xFFFF); - if (ret_val) - return ret_val; - ret_val = e1000_read_kmrn_reg(hw, GG82563_REG(0x34, 9), ®_data); - if (ret_val) - return ret_val; - reg_data |= 0x3F; - ret_val = e1000_write_kmrn_reg(hw, GG82563_REG(0x34, 9), reg_data); - if (ret_val) - return ret_val; - default: - break; - } - - /* Check if it is a valid PHY and set PHY mode if necessary. */ - ret_val = e1000_copper_link_preconfig(hw); - if (ret_val) - return ret_val; - - switch (hw->mac_type) { - case e1000_80003es2lan: - /* Kumeran registers are written-only */ - reg_data = E1000_KUMCTRLSTA_INB_CTRL_LINK_STATUS_TX_TIMEOUT_DEFAULT; - reg_data |= E1000_KUMCTRLSTA_INB_CTRL_DIS_PADDING; - ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_INB_CTRL, - reg_data); - if (ret_val) - return ret_val; - break; - default: - break; - } - - if (hw->phy_type == e1000_phy_igp || - hw->phy_type == e1000_phy_igp_3 || - hw->phy_type == e1000_phy_igp_2) { - ret_val = e1000_copper_link_igp_setup(hw); - if (ret_val) - return ret_val; - } else if (hw->phy_type == e1000_phy_m88) { - ret_val = e1000_copper_link_mgp_setup(hw); - if (ret_val) - return ret_val; - } else if (hw->phy_type == e1000_phy_gg82563) { - ret_val = e1000_copper_link_ggp_setup(hw); - if (ret_val) - return ret_val; - } - - if (hw->autoneg) { - /* Setup autoneg and flow control advertisement - * and perform autonegotiation */ - ret_val = e1000_copper_link_autoneg(hw); - if (ret_val) - return ret_val; - } else { - /* PHY will be set to 10H, 10F, 100H,or 100F - * depending on value from forced_speed_duplex. */ - DEBUGOUT("Forcing speed and duplex\n"); - ret_val = e1000_phy_force_speed_duplex(hw); - if (ret_val) { - DEBUGOUT("Error Forcing Speed and Duplex\n"); - return ret_val; - } - } - - /* Check link status. Wait up to 100 microseconds for link to become - * valid. - */ - for (i = 0; i < 10; i++) { - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if (phy_data & MII_SR_LINK_STATUS) { - /* Config the MAC and PHY after link is up */ - ret_val = e1000_copper_link_postconfig(hw); - if (ret_val) - return ret_val; - - DEBUGOUT("Valid link established!!!\n"); - return E1000_SUCCESS; - } - udelay(10); - } - - DEBUGOUT("Unable to establish link!!!\n"); - return E1000_SUCCESS; + s32 ret_val; + u16 i; + u16 phy_data; + + DEBUGFUNC("e1000_setup_copper_link"); + + /* Check if it is a valid PHY and set PHY mode if necessary. */ + ret_val = e1000_copper_link_preconfig(hw); + if (ret_val) + return ret_val; + + if (hw->phy_type == e1000_phy_igp) { + ret_val = e1000_copper_link_igp_setup(hw); + if (ret_val) + return ret_val; + } else if (hw->phy_type == e1000_phy_m88) { + ret_val = e1000_copper_link_mgp_setup(hw); + if (ret_val) + return ret_val; + } + + if (hw->autoneg) { + /* Setup autoneg and flow control advertisement + * and perform autonegotiation */ + ret_val = e1000_copper_link_autoneg(hw); + if (ret_val) + return ret_val; + } else { + /* PHY will be set to 10H, 10F, 100H,or 100F + * depending on value from forced_speed_duplex. */ + DEBUGOUT("Forcing speed and duplex\n"); + ret_val = e1000_phy_force_speed_duplex(hw); + if (ret_val) { + DEBUGOUT("Error Forcing Speed and Duplex\n"); + return ret_val; + } + } + + /* Check link status. Wait up to 100 microseconds for link to become + * valid. + */ + for (i = 0; i < 10; i++) { + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if (phy_data & MII_SR_LINK_STATUS) { + /* Config the MAC and PHY after link is up */ + ret_val = e1000_copper_link_postconfig(hw); + if (ret_val) + return ret_val; + + DEBUGOUT("Valid link established!!!\n"); + return E1000_SUCCESS; + } + udelay(10); + } + + DEBUGOUT("Unable to establish link!!!\n"); + return E1000_SUCCESS; } -/****************************************************************************** -* Configure the MAC-to-PHY interface for 10/100Mbps -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static s32 e1000_configure_kmrn_for_10_100(struct e1000_hw *hw, u16 duplex) +/** + * e1000_phy_setup_autoneg - phy settings + * @hw: Struct containing variables accessed by shared code + * + * Configures PHY autoneg and flow control advertisement settings + */ +s32 e1000_phy_setup_autoneg(struct e1000_hw *hw) { - s32 ret_val = E1000_SUCCESS; - u32 tipg; - u16 reg_data; + s32 ret_val; + u16 mii_autoneg_adv_reg; + u16 mii_1000t_ctrl_reg; - DEBUGFUNC("e1000_configure_kmrn_for_10_100"); + DEBUGFUNC("e1000_phy_setup_autoneg"); - reg_data = E1000_KUMCTRLSTA_HD_CTRL_10_100_DEFAULT; - ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, - reg_data); - if (ret_val) - return ret_val; + /* Read the MII Auto-Neg Advertisement Register (Address 4). */ + ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); + if (ret_val) + return ret_val; - /* Configure Transmit Inter-Packet Gap */ - tipg = er32(TIPG); - tipg &= ~E1000_TIPG_IPGT_MASK; - tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_10_100; - ew32(TIPG, tipg); + /* Read the MII 1000Base-T Control Register (Address 9). */ + ret_val = + e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); + /* Need to parse both autoneg_advertised and fc and set up + * the appropriate PHY registers. First we will parse for + * autoneg_advertised software override. Since we can advertise + * a plethora of combinations, we need to check each bit + * individually. + */ - if (ret_val) - return ret_val; + /* First we clear all the 10/100 mb speed bits in the Auto-Neg + * Advertisement Register (Address 4) and the 1000 mb speed bits in + * the 1000Base-T Control Register (Address 9). + */ + mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; + mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; - if (duplex == HALF_DUPLEX) - reg_data |= GG82563_KMCR_PASS_FALSE_CARRIER; - else - reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; + DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised); - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + /* Do we want to advertise 10 Mb Half Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_10_HALF) { + DEBUGOUT("Advertise 10mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; + } - return ret_val; -} + /* Do we want to advertise 10 Mb Full Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_10_FULL) { + DEBUGOUT("Advertise 10mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; + } -static s32 e1000_configure_kmrn_for_1000(struct e1000_hw *hw) -{ - s32 ret_val = E1000_SUCCESS; - u16 reg_data; - u32 tipg; + /* Do we want to advertise 100 Mb Half Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_100_HALF) { + DEBUGOUT("Advertise 100mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; + } - DEBUGFUNC("e1000_configure_kmrn_for_1000"); + /* Do we want to advertise 100 Mb Full Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_100_FULL) { + DEBUGOUT("Advertise 100mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; + } - reg_data = E1000_KUMCTRLSTA_HD_CTRL_1000_DEFAULT; - ret_val = e1000_write_kmrn_reg(hw, E1000_KUMCTRLSTA_OFFSET_HD_CTRL, - reg_data); - if (ret_val) - return ret_val; + /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ + if (hw->autoneg_advertised & ADVERTISE_1000_HALF) { + DEBUGOUT + ("Advertise 1000mb Half duplex requested, request denied!\n"); + } - /* Configure Transmit Inter-Packet Gap */ - tipg = er32(TIPG); - tipg &= ~E1000_TIPG_IPGT_MASK; - tipg |= DEFAULT_80003ES2LAN_TIPG_IPGT_1000; - ew32(TIPG, tipg); + /* Do we want to advertise 1000 Mb Full Duplex? */ + if (hw->autoneg_advertised & ADVERTISE_1000_FULL) { + DEBUGOUT("Advertise 1000mb Full duplex\n"); + mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; + } - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, ®_data); + /* Check for a software override of the flow control settings, and + * setup the PHY advertisement registers accordingly. If + * auto-negotiation is enabled, then software will have to set the + * "PAUSE" bits to the correct value in the Auto-Negotiation + * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * but we do not support receiving pause frames). + * 3: Both Rx and TX flow control (symmetric) are enabled. + * other: No software override. The flow control configuration + * in the EEPROM is used. + */ + switch (hw->fc) { + case E1000_FC_NONE: /* 0 */ + /* Flow control (RX & TX) is completely disabled by a + * software over-ride. + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case E1000_FC_RX_PAUSE: /* 1 */ + /* RX Flow control is enabled, and TX Flow control is + * disabled, by a software over-ride. + */ + /* Since there really isn't a way to advertise that we are + * capable of RX Pause ONLY, we will advertise that we + * support both symmetric and asymmetric RX PAUSE. Later + * (in e1000_config_fc_after_link_up) we will disable the + *hw's ability to send PAUSE frames. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case E1000_FC_TX_PAUSE: /* 2 */ + /* TX Flow control is enabled, and RX Flow control is + * disabled, by a software over-ride. + */ + mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; + mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; + break; + case E1000_FC_FULL: /* 3 */ + /* Flow control (both RX and TX) is enabled by a software + * over-ride. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + return -E1000_ERR_CONFIG; + } - if (ret_val) - return ret_val; + ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); + if (ret_val) + return ret_val; - reg_data &= ~GG82563_KMCR_PASS_FALSE_CARRIER; - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_KMRN_MODE_CTRL, reg_data); + DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); - return ret_val; -} + ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; -/****************************************************************************** -* Configures PHY autoneg and flow control advertisement settings -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -s32 e1000_phy_setup_autoneg(struct e1000_hw *hw) -{ - s32 ret_val; - u16 mii_autoneg_adv_reg; - u16 mii_1000t_ctrl_reg; - - DEBUGFUNC("e1000_phy_setup_autoneg"); - - /* Read the MII Auto-Neg Advertisement Register (Address 4). */ - ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); - if (ret_val) - return ret_val; - - if (hw->phy_type != e1000_phy_ife) { - /* Read the MII 1000Base-T Control Register (Address 9). */ - ret_val = e1000_read_phy_reg(hw, PHY_1000T_CTRL, &mii_1000t_ctrl_reg); - if (ret_val) - return ret_val; - } else - mii_1000t_ctrl_reg=0; - - /* Need to parse both autoneg_advertised and fc and set up - * the appropriate PHY registers. First we will parse for - * autoneg_advertised software override. Since we can advertise - * a plethora of combinations, we need to check each bit - * individually. - */ - - /* First we clear all the 10/100 mb speed bits in the Auto-Neg - * Advertisement Register (Address 4) and the 1000 mb speed bits in - * the 1000Base-T Control Register (Address 9). - */ - mii_autoneg_adv_reg &= ~REG4_SPEED_MASK; - mii_1000t_ctrl_reg &= ~REG9_SPEED_MASK; - - DEBUGOUT1("autoneg_advertised %x\n", hw->autoneg_advertised); - - /* Do we want to advertise 10 Mb Half Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_10_HALF) { - DEBUGOUT("Advertise 10mb Half duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; - } - - /* Do we want to advertise 10 Mb Full Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_10_FULL) { - DEBUGOUT("Advertise 10mb Full duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; - } - - /* Do we want to advertise 100 Mb Half Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_100_HALF) { - DEBUGOUT("Advertise 100mb Half duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; - } - - /* Do we want to advertise 100 Mb Full Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_100_FULL) { - DEBUGOUT("Advertise 100mb Full duplex\n"); - mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; - } - - /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ - if (hw->autoneg_advertised & ADVERTISE_1000_HALF) { - DEBUGOUT("Advertise 1000mb Half duplex requested, request denied!\n"); - } - - /* Do we want to advertise 1000 Mb Full Duplex? */ - if (hw->autoneg_advertised & ADVERTISE_1000_FULL) { - DEBUGOUT("Advertise 1000mb Full duplex\n"); - mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; - if (hw->phy_type == e1000_phy_ife) { - DEBUGOUT("e1000_phy_ife is a 10/100 PHY. Gigabit speed is not supported.\n"); - } - } - - /* Check for a software override of the flow control settings, and - * setup the PHY advertisement registers accordingly. If - * auto-negotiation is enabled, then software will have to set the - * "PAUSE" bits to the correct value in the Auto-Negotiation - * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-negotiation. - * - * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause frames - * but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames - * but we do not support receiving pause frames). - * 3: Both Rx and TX flow control (symmetric) are enabled. - * other: No software override. The flow control configuration - * in the EEPROM is used. - */ - switch (hw->fc) { - case E1000_FC_NONE: /* 0 */ - /* Flow control (RX & TX) is completely disabled by a - * software over-ride. - */ - mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); - break; - case E1000_FC_RX_PAUSE: /* 1 */ - /* RX Flow control is enabled, and TX Flow control is - * disabled, by a software over-ride. - */ - /* Since there really isn't a way to advertise that we are - * capable of RX Pause ONLY, we will advertise that we - * support both symmetric and asymmetric RX PAUSE. Later - * (in e1000_config_fc_after_link_up) we will disable the - *hw's ability to send PAUSE frames. - */ - mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); - break; - case E1000_FC_TX_PAUSE: /* 2 */ - /* TX Flow control is enabled, and RX Flow control is - * disabled, by a software over-ride. - */ - mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; - mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; - break; - case E1000_FC_FULL: /* 3 */ - /* Flow control (both RX and TX) is enabled by a software - * over-ride. - */ - mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); - break; - default: - DEBUGOUT("Flow control param set incorrectly\n"); - return -E1000_ERR_CONFIG; - } - - ret_val = e1000_write_phy_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); - if (ret_val) - return ret_val; - - DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); - - if (hw->phy_type != e1000_phy_ife) { - ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; + return E1000_SUCCESS; } -/****************************************************************************** -* Force PHY speed and duplex settings to hw->forced_speed_duplex -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ +/** + * e1000_phy_force_speed_duplex - force link settings + * @hw: Struct containing variables accessed by shared code + * + * Force PHY speed and duplex settings to hw->forced_speed_duplex + */ static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw) { - u32 ctrl; - s32 ret_val; - u16 mii_ctrl_reg; - u16 mii_status_reg; - u16 phy_data; - u16 i; - - DEBUGFUNC("e1000_phy_force_speed_duplex"); - - /* Turn off Flow control if we are forcing speed and duplex. */ - hw->fc = E1000_FC_NONE; - - DEBUGOUT1("hw->fc = %d\n", hw->fc); - - /* Read the Device Control Register. */ - ctrl = er32(CTRL); - - /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */ - ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); - ctrl &= ~(DEVICE_SPEED_MASK); - - /* Clear the Auto Speed Detect Enable bit. */ - ctrl &= ~E1000_CTRL_ASDE; - - /* Read the MII Control Register. */ - ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg); - if (ret_val) - return ret_val; - - /* We need to disable autoneg in order to force link and duplex. */ - - mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN; - - /* Are we forcing Full or Half Duplex? */ - if (hw->forced_speed_duplex == e1000_100_full || - hw->forced_speed_duplex == e1000_10_full) { - /* We want to force full duplex so we SET the full duplex bits in the - * Device and MII Control Registers. - */ - ctrl |= E1000_CTRL_FD; - mii_ctrl_reg |= MII_CR_FULL_DUPLEX; - DEBUGOUT("Full Duplex\n"); - } else { - /* We want to force half duplex so we CLEAR the full duplex bits in - * the Device and MII Control Registers. - */ - ctrl &= ~E1000_CTRL_FD; - mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX; - DEBUGOUT("Half Duplex\n"); - } - - /* Are we forcing 100Mbps??? */ - if (hw->forced_speed_duplex == e1000_100_full || - hw->forced_speed_duplex == e1000_100_half) { - /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */ - ctrl |= E1000_CTRL_SPD_100; - mii_ctrl_reg |= MII_CR_SPEED_100; - mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10); - DEBUGOUT("Forcing 100mb "); - } else { - /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */ - ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); - mii_ctrl_reg |= MII_CR_SPEED_10; - mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100); - DEBUGOUT("Forcing 10mb "); - } - - e1000_config_collision_dist(hw); - - /* Write the configured values back to the Device Control Reg. */ - ew32(CTRL, ctrl); - - if ((hw->phy_type == e1000_phy_m88) || - (hw->phy_type == e1000_phy_gg82563)) { - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI - * forced whenever speed are duplex are forced. - */ - phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data); - - /* Need to reset the PHY or these changes will be ignored */ - mii_ctrl_reg |= MII_CR_RESET; - - /* Disable MDI-X support for 10/100 */ - } else if (hw->phy_type == e1000_phy_ife) { - ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IFE_PMC_AUTO_MDIX; - phy_data &= ~IFE_PMC_FORCE_MDIX; - - ret_val = e1000_write_phy_reg(hw, IFE_PHY_MDIX_CONTROL, phy_data); - if (ret_val) - return ret_val; - - } else { - /* Clear Auto-Crossover to force MDI manually. IGP requires MDI - * forced whenever speed or duplex are forced. - */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; - phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; - - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); - if (ret_val) - return ret_val; - } - - /* Write back the modified PHY MII control register. */ - ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg); - if (ret_val) - return ret_val; - - udelay(1); - - /* The wait_autoneg_complete flag may be a little misleading here. - * Since we are forcing speed and duplex, Auto-Neg is not enabled. - * But we do want to delay for a period while forcing only so we - * don't generate false No Link messages. So we will wait here - * only if the user has set wait_autoneg_complete to 1, which is - * the default. - */ - if (hw->wait_autoneg_complete) { - /* We will wait for autoneg to complete. */ - DEBUGOUT("Waiting for forced speed/duplex link.\n"); - mii_status_reg = 0; - - /* We will wait for autoneg to complete or 4.5 seconds to expire. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Auto-Neg Complete bit - * to be set. - */ - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if (mii_status_reg & MII_SR_LINK_STATUS) break; - msleep(100); - } - if ((i == 0) && - ((hw->phy_type == e1000_phy_m88) || - (hw->phy_type == e1000_phy_gg82563))) { - /* We didn't get link. Reset the DSP and wait again for link. */ - ret_val = e1000_phy_reset_dsp(hw); - if (ret_val) { - DEBUGOUT("Error Resetting PHY DSP\n"); - return ret_val; - } - } - /* This loop will early-out if the link condition has been met. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - if (mii_status_reg & MII_SR_LINK_STATUS) break; - msleep(100); - /* Read the MII Status Register and wait for Auto-Neg Complete bit - * to be set. - */ - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - } - } - - if (hw->phy_type == e1000_phy_m88) { - /* Because we reset the PHY above, we need to re-force TX_CLK in the - * Extended PHY Specific Control Register to 25MHz clock. This value - * defaults back to a 2.5MHz clock when the PHY is reset. - */ - ret_val = e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_EPSCR_TX_CLK_25; - ret_val = e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - /* In addition, because of the s/w reset above, we need to enable CRS on - * TX. This must be set for both full and half duplex operation. - */ - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - - if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) && - (!hw->autoneg) && (hw->forced_speed_duplex == e1000_10_full || - hw->forced_speed_duplex == e1000_10_half)) { - ret_val = e1000_polarity_reversal_workaround(hw); - if (ret_val) - return ret_val; - } - } else if (hw->phy_type == e1000_phy_gg82563) { - /* The TX_CLK of the Extended PHY Specific Control Register defaults - * to 2.5MHz on a reset. We need to re-force it back to 25MHz, if - * we're not in a forced 10/duplex configuration. */ - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~GG82563_MSCR_TX_CLK_MASK; - if ((hw->forced_speed_duplex == e1000_10_full) || - (hw->forced_speed_duplex == e1000_10_half)) - phy_data |= GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ; - else - phy_data |= GG82563_MSCR_TX_CLK_100MBPS_25MHZ; - - /* Also due to the reset, we need to enable CRS on Tx. */ - phy_data |= GG82563_MSCR_ASSERT_CRS_ON_TX; - - ret_val = e1000_write_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL, phy_data); - if (ret_val) - return ret_val; - } - return E1000_SUCCESS; + u32 ctrl; + s32 ret_val; + u16 mii_ctrl_reg; + u16 mii_status_reg; + u16 phy_data; + u16 i; + + DEBUGFUNC("e1000_phy_force_speed_duplex"); + + /* Turn off Flow control if we are forcing speed and duplex. */ + hw->fc = E1000_FC_NONE; + + DEBUGOUT1("hw->fc = %d\n", hw->fc); + + /* Read the Device Control Register. */ + ctrl = er32(CTRL); + + /* Set the bits to Force Speed and Duplex in the Device Ctrl Reg. */ + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ctrl &= ~(DEVICE_SPEED_MASK); + + /* Clear the Auto Speed Detect Enable bit. */ + ctrl &= ~E1000_CTRL_ASDE; + + /* Read the MII Control Register. */ + ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &mii_ctrl_reg); + if (ret_val) + return ret_val; + + /* We need to disable autoneg in order to force link and duplex. */ + + mii_ctrl_reg &= ~MII_CR_AUTO_NEG_EN; + + /* Are we forcing Full or Half Duplex? */ + if (hw->forced_speed_duplex == e1000_100_full || + hw->forced_speed_duplex == e1000_10_full) { + /* We want to force full duplex so we SET the full duplex bits in the + * Device and MII Control Registers. + */ + ctrl |= E1000_CTRL_FD; + mii_ctrl_reg |= MII_CR_FULL_DUPLEX; + DEBUGOUT("Full Duplex\n"); + } else { + /* We want to force half duplex so we CLEAR the full duplex bits in + * the Device and MII Control Registers. + */ + ctrl &= ~E1000_CTRL_FD; + mii_ctrl_reg &= ~MII_CR_FULL_DUPLEX; + DEBUGOUT("Half Duplex\n"); + } + + /* Are we forcing 100Mbps??? */ + if (hw->forced_speed_duplex == e1000_100_full || + hw->forced_speed_duplex == e1000_100_half) { + /* Set the 100Mb bit and turn off the 1000Mb and 10Mb bits. */ + ctrl |= E1000_CTRL_SPD_100; + mii_ctrl_reg |= MII_CR_SPEED_100; + mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_10); + DEBUGOUT("Forcing 100mb "); + } else { + /* Set the 10Mb bit and turn off the 1000Mb and 100Mb bits. */ + ctrl &= ~(E1000_CTRL_SPD_1000 | E1000_CTRL_SPD_100); + mii_ctrl_reg |= MII_CR_SPEED_10; + mii_ctrl_reg &= ~(MII_CR_SPEED_1000 | MII_CR_SPEED_100); + DEBUGOUT("Forcing 10mb "); + } + + e1000_config_collision_dist(hw); + + /* Write the configured values back to the Device Control Reg. */ + ew32(CTRL, ctrl); + + if (hw->phy_type == e1000_phy_m88) { + ret_val = + e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + /* Clear Auto-Crossover to force MDI manually. M88E1000 requires MDI + * forced whenever speed are duplex are forced. + */ + phy_data &= ~M88E1000_PSCR_AUTO_X_MODE; + ret_val = + e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + + DEBUGOUT1("M88E1000 PSCR: %x \n", phy_data); + + /* Need to reset the PHY or these changes will be ignored */ + mii_ctrl_reg |= MII_CR_RESET; + + /* Disable MDI-X support for 10/100 */ + } else { + /* Clear Auto-Crossover to force MDI manually. IGP requires MDI + * forced whenever speed or duplex are forced. + */ + ret_val = + e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PSCR_AUTO_MDIX; + phy_data &= ~IGP01E1000_PSCR_FORCE_MDI_MDIX; + + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CTRL, phy_data); + if (ret_val) + return ret_val; + } + + /* Write back the modified PHY MII control register. */ + ret_val = e1000_write_phy_reg(hw, PHY_CTRL, mii_ctrl_reg); + if (ret_val) + return ret_val; + + udelay(1); + + /* The wait_autoneg_complete flag may be a little misleading here. + * Since we are forcing speed and duplex, Auto-Neg is not enabled. + * But we do want to delay for a period while forcing only so we + * don't generate false No Link messages. So we will wait here + * only if the user has set wait_autoneg_complete to 1, which is + * the default. + */ + if (hw->wait_autoneg_complete) { + /* We will wait for autoneg to complete. */ + DEBUGOUT("Waiting for forced speed/duplex link.\n"); + mii_status_reg = 0; + + /* We will wait for autoneg to complete or 4.5 seconds to expire. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Auto-Neg Complete bit + * to be set. + */ + ret_val = + e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + ret_val = + e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + if (mii_status_reg & MII_SR_LINK_STATUS) + break; + msleep(100); + } + if ((i == 0) && (hw->phy_type == e1000_phy_m88)) { + /* We didn't get link. Reset the DSP and wait again for link. */ + ret_val = e1000_phy_reset_dsp(hw); + if (ret_val) { + DEBUGOUT("Error Resetting PHY DSP\n"); + return ret_val; + } + } + /* This loop will early-out if the link condition has been met. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + if (mii_status_reg & MII_SR_LINK_STATUS) + break; + msleep(100); + /* Read the MII Status Register and wait for Auto-Neg Complete bit + * to be set. + */ + ret_val = + e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + ret_val = + e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + } + } + + if (hw->phy_type == e1000_phy_m88) { + /* Because we reset the PHY above, we need to re-force TX_CLK in the + * Extended PHY Specific Control Register to 25MHz clock. This value + * defaults back to a 2.5MHz clock when the PHY is reset. + */ + ret_val = + e1000_read_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, + &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_EPSCR_TX_CLK_25; + ret_val = + e1000_write_phy_reg(hw, M88E1000_EXT_PHY_SPEC_CTRL, + phy_data); + if (ret_val) + return ret_val; + + /* In addition, because of the s/w reset above, we need to enable CRS on + * TX. This must be set for both full and half duplex operation. + */ + ret_val = + e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_data |= M88E1000_PSCR_ASSERT_CRS_ON_TX; + ret_val = + e1000_write_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, phy_data); + if (ret_val) + return ret_val; + + if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) + && (!hw->autoneg) + && (hw->forced_speed_duplex == e1000_10_full + || hw->forced_speed_duplex == e1000_10_half)) { + ret_val = e1000_polarity_reversal_workaround(hw); + if (ret_val) + return ret_val; + } + } + return E1000_SUCCESS; } -/****************************************************************************** -* Sets the collision distance in the Transmit Control register -* -* hw - Struct containing variables accessed by shared code -* -* Link should have been established previously. Reads the speed and duplex -* information from the Device Status register. -******************************************************************************/ +/** + * e1000_config_collision_dist - set collision distance register + * @hw: Struct containing variables accessed by shared code + * + * Sets the collision distance in the Transmit Control register. + * Link should have been established previously. Reads the speed and duplex + * information from the Device Status register. + */ void e1000_config_collision_dist(struct e1000_hw *hw) { - u32 tctl, coll_dist; + u32 tctl, coll_dist; - DEBUGFUNC("e1000_config_collision_dist"); + DEBUGFUNC("e1000_config_collision_dist"); - if (hw->mac_type < e1000_82543) - coll_dist = E1000_COLLISION_DISTANCE_82542; - else - coll_dist = E1000_COLLISION_DISTANCE; + if (hw->mac_type < e1000_82543) + coll_dist = E1000_COLLISION_DISTANCE_82542; + else + coll_dist = E1000_COLLISION_DISTANCE; - tctl = er32(TCTL); + tctl = er32(TCTL); - tctl &= ~E1000_TCTL_COLD; - tctl |= coll_dist << E1000_COLD_SHIFT; + tctl &= ~E1000_TCTL_COLD; + tctl |= coll_dist << E1000_COLD_SHIFT; - ew32(TCTL, tctl); - E1000_WRITE_FLUSH(); + ew32(TCTL, tctl); + E1000_WRITE_FLUSH(); } -/****************************************************************************** -* Sets MAC speed and duplex settings to reflect the those in the PHY -* -* hw - Struct containing variables accessed by shared code -* mii_reg - data to write to the MII control register -* -* The contents of the PHY register containing the needed information need to -* be passed in. -******************************************************************************/ +/** + * e1000_config_mac_to_phy - sync phy and mac settings + * @hw: Struct containing variables accessed by shared code + * @mii_reg: data to write to the MII control register + * + * Sets MAC speed and duplex settings to reflect the those in the PHY + * The contents of the PHY register containing the needed information need to + * be passed in. + */ static s32 e1000_config_mac_to_phy(struct e1000_hw *hw) { - u32 ctrl; - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_config_mac_to_phy"); - - /* 82544 or newer MAC, Auto Speed Detection takes care of - * MAC speed/duplex configuration.*/ - if (hw->mac_type >= e1000_82544) - return E1000_SUCCESS; - - /* Read the Device Control Register and set the bits to Force Speed - * and Duplex. - */ - ctrl = er32(CTRL); - ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); - ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS); - - /* Set up duplex in the Device Control and Transmit Control - * registers depending on negotiated values. - */ - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if (phy_data & M88E1000_PSSR_DPLX) - ctrl |= E1000_CTRL_FD; - else - ctrl &= ~E1000_CTRL_FD; - - e1000_config_collision_dist(hw); - - /* Set up speed in the Device Control register depending on - * negotiated values. - */ - if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) - ctrl |= E1000_CTRL_SPD_1000; - else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) - ctrl |= E1000_CTRL_SPD_100; - - /* Write the configured values back to the Device Control Reg. */ - ew32(CTRL, ctrl); - return E1000_SUCCESS; + u32 ctrl; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_config_mac_to_phy"); + + /* 82544 or newer MAC, Auto Speed Detection takes care of + * MAC speed/duplex configuration.*/ + if (hw->mac_type >= e1000_82544) + return E1000_SUCCESS; + + /* Read the Device Control Register and set the bits to Force Speed + * and Duplex. + */ + ctrl = er32(CTRL); + ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); + ctrl &= ~(E1000_CTRL_SPD_SEL | E1000_CTRL_ILOS); + + /* Set up duplex in the Device Control and Transmit Control + * registers depending on negotiated values. + */ + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if (phy_data & M88E1000_PSSR_DPLX) + ctrl |= E1000_CTRL_FD; + else + ctrl &= ~E1000_CTRL_FD; + + e1000_config_collision_dist(hw); + + /* Set up speed in the Device Control register depending on + * negotiated values. + */ + if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) + ctrl |= E1000_CTRL_SPD_1000; + else if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_100MBS) + ctrl |= E1000_CTRL_SPD_100; + + /* Write the configured values back to the Device Control Reg. */ + ew32(CTRL, ctrl); + return E1000_SUCCESS; } -/****************************************************************************** - * Forces the MAC's flow control settings. - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_force_mac_fc - force flow control settings + * @hw: Struct containing variables accessed by shared code * + * Forces the MAC's flow control settings. * Sets the TFCE and RFCE bits in the device control register to reflect * the adapter settings. TFCE and RFCE need to be explicitly set by * software when a Copper PHY is used because autonegotiation is managed * by the PHY rather than the MAC. Software must also configure these * bits when link is forced on a fiber connection. - *****************************************************************************/ + */ s32 e1000_force_mac_fc(struct e1000_hw *hw) { - u32 ctrl; - - DEBUGFUNC("e1000_force_mac_fc"); - - /* Get the current configuration of the Device Control Register */ - ctrl = er32(CTRL); - - /* Because we didn't get link via the internal auto-negotiation - * mechanism (we either forced link or we got link via PHY - * auto-neg), we have to manually enable/disable transmit an - * receive flow control. - * - * The "Case" statement below enables/disable flow control - * according to the "hw->fc" parameter. - * - * The possible values of the "fc" parameter are: - * 0: Flow control is completely disabled - * 1: Rx flow control is enabled (we can receive pause - * frames but not send pause frames). - * 2: Tx flow control is enabled (we can send pause frames - * frames but we do not receive pause frames). - * 3: Both Rx and TX flow control (symmetric) is enabled. - * other: No other values should be possible at this point. - */ - - switch (hw->fc) { - case E1000_FC_NONE: - ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); - break; - case E1000_FC_RX_PAUSE: - ctrl &= (~E1000_CTRL_TFCE); - ctrl |= E1000_CTRL_RFCE; - break; - case E1000_FC_TX_PAUSE: - ctrl &= (~E1000_CTRL_RFCE); - ctrl |= E1000_CTRL_TFCE; - break; - case E1000_FC_FULL: - ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); - break; - default: - DEBUGOUT("Flow control param set incorrectly\n"); - return -E1000_ERR_CONFIG; - } - - /* Disable TX Flow Control for 82542 (rev 2.0) */ - if (hw->mac_type == e1000_82542_rev2_0) - ctrl &= (~E1000_CTRL_TFCE); - - ew32(CTRL, ctrl); - return E1000_SUCCESS; + u32 ctrl; + + DEBUGFUNC("e1000_force_mac_fc"); + + /* Get the current configuration of the Device Control Register */ + ctrl = er32(CTRL); + + /* Because we didn't get link via the internal auto-negotiation + * mechanism (we either forced link or we got link via PHY + * auto-neg), we have to manually enable/disable transmit an + * receive flow control. + * + * The "Case" statement below enables/disable flow control + * according to the "hw->fc" parameter. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause + * frames but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * frames but we do not receive pause frames). + * 3: Both Rx and TX flow control (symmetric) is enabled. + * other: No other values should be possible at this point. + */ + + switch (hw->fc) { + case E1000_FC_NONE: + ctrl &= (~(E1000_CTRL_TFCE | E1000_CTRL_RFCE)); + break; + case E1000_FC_RX_PAUSE: + ctrl &= (~E1000_CTRL_TFCE); + ctrl |= E1000_CTRL_RFCE; + break; + case E1000_FC_TX_PAUSE: + ctrl &= (~E1000_CTRL_RFCE); + ctrl |= E1000_CTRL_TFCE; + break; + case E1000_FC_FULL: + ctrl |= (E1000_CTRL_TFCE | E1000_CTRL_RFCE); + break; + default: + DEBUGOUT("Flow control param set incorrectly\n"); + return -E1000_ERR_CONFIG; + } + + /* Disable TX Flow Control for 82542 (rev 2.0) */ + if (hw->mac_type == e1000_82542_rev2_0) + ctrl &= (~E1000_CTRL_TFCE); + + ew32(CTRL, ctrl); + return E1000_SUCCESS; } -/****************************************************************************** - * Configures flow control settings after link is established - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_config_fc_after_link_up - configure flow control after autoneg + * @hw: Struct containing variables accessed by shared code * + * Configures flow control settings after link is established * Should be called immediately after a valid link has been established. * Forces MAC flow control settings if link was forced. When in MII/GMII mode * and autonegotiation is enabled, the MAC flow control settings will be set * based on the flow control negotiated by the PHY. In TBI mode, the TFCE - * and RFCE bits will be automaticaly set to the negotiated flow control mode. - *****************************************************************************/ + * and RFCE bits will be automatically set to the negotiated flow control mode. + */ static s32 e1000_config_fc_after_link_up(struct e1000_hw *hw) { - s32 ret_val; - u16 mii_status_reg; - u16 mii_nway_adv_reg; - u16 mii_nway_lp_ability_reg; - u16 speed; - u16 duplex; - - DEBUGFUNC("e1000_config_fc_after_link_up"); - - /* Check for the case where we have fiber media and auto-neg failed - * so we had to force link. In this case, we need to force the - * configuration of the MAC to match the "fc" parameter. - */ - if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) || - ((hw->media_type == e1000_media_type_internal_serdes) && - (hw->autoneg_failed)) || - ((hw->media_type == e1000_media_type_copper) && (!hw->autoneg))) { - ret_val = e1000_force_mac_fc(hw); - if (ret_val) { - DEBUGOUT("Error forcing flow control settings\n"); - return ret_val; - } - } - - /* Check for the case where we have copper media and auto-neg is - * enabled. In this case, we need to check and see if Auto-Neg - * has completed, and if so, how the PHY and link partner has - * flow control configured. - */ - if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) { - /* Read the MII Status Register and check to see if AutoNeg - * has completed. We read this twice because this reg has - * some "sticky" (latched) bits. - */ - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { - /* The AutoNeg process has completed, so we now need to - * read both the Auto Negotiation Advertisement Register - * (Address 4) and the Auto_Negotiation Base Page Ability - * Register (Address 5) to determine how flow control was - * negotiated. - */ - ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, - &mii_nway_adv_reg); - if (ret_val) - return ret_val; - ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, - &mii_nway_lp_ability_reg); - if (ret_val) - return ret_val; - - /* Two bits in the Auto Negotiation Advertisement Register - * (Address 4) and two bits in the Auto Negotiation Base - * Page Ability Register (Address 5) determine flow control - * for both the PHY and the link partner. The following - * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, - * 1999, describes these PAUSE resolution bits and how flow - * control is determined based upon these settings. - * NOTE: DC = Don't Care - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution - *-------|---------|-------|---------|-------------------- - * 0 | 0 | DC | DC | E1000_FC_NONE - * 0 | 1 | 0 | DC | E1000_FC_NONE - * 0 | 1 | 1 | 0 | E1000_FC_NONE - * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE - * 1 | 0 | 0 | DC | E1000_FC_NONE - * 1 | DC | 1 | DC | E1000_FC_FULL - * 1 | 1 | 0 | 0 | E1000_FC_NONE - * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE - * - */ - /* Are both PAUSE bits set to 1? If so, this implies - * Symmetric Flow Control is enabled at both ends. The - * ASM_DIR bits are irrelevant per the spec. - * - * For Symmetric Flow Control: - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- - * 1 | DC | 1 | DC | E1000_FC_FULL - * - */ - if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { - /* Now we need to check if the user selected RX ONLY - * of pause frames. In this case, we had to advertise - * FULL flow control because we could not advertise RX - * ONLY. Hence, we must now check to see if we need to - * turn OFF the TRANSMISSION of PAUSE frames. - */ - if (hw->original_fc == E1000_FC_FULL) { - hw->fc = E1000_FC_FULL; - DEBUGOUT("Flow Control = FULL.\n"); - } else { - hw->fc = E1000_FC_RX_PAUSE; - DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); - } - } - /* For receiving PAUSE frames ONLY. - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- - * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE - * - */ - else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && - (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { - hw->fc = E1000_FC_TX_PAUSE; - DEBUGOUT("Flow Control = TX PAUSE frames only.\n"); - } - /* For transmitting PAUSE frames ONLY. - * - * LOCAL DEVICE | LINK PARTNER - * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result - *-------|---------|-------|---------|-------------------- - * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE - * - */ - else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && - (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && - !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && - (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) { - hw->fc = E1000_FC_RX_PAUSE; - DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); - } - /* Per the IEEE spec, at this point flow control should be - * disabled. However, we want to consider that we could - * be connected to a legacy switch that doesn't advertise - * desired flow control, but can be forced on the link - * partner. So if we advertised no flow control, that is - * what we will resolve to. If we advertised some kind of - * receive capability (Rx Pause Only or Full Flow Control) - * and the link partner advertised none, we will configure - * ourselves to enable Rx Flow Control only. We can do - * this safely for two reasons: If the link partner really - * didn't want flow control enabled, and we enable Rx, no - * harm done since we won't be receiving any PAUSE frames - * anyway. If the intent on the link partner was to have - * flow control enabled, then by us enabling RX only, we - * can at least receive pause frames and process them. - * This is a good idea because in most cases, since we are - * predominantly a server NIC, more times than not we will - * be asked to delay transmission of packets than asking - * our link partner to pause transmission of frames. - */ - else if ((hw->original_fc == E1000_FC_NONE || - hw->original_fc == E1000_FC_TX_PAUSE) || - hw->fc_strict_ieee) { - hw->fc = E1000_FC_NONE; - DEBUGOUT("Flow Control = NONE.\n"); - } else { - hw->fc = E1000_FC_RX_PAUSE; - DEBUGOUT("Flow Control = RX PAUSE frames only.\n"); - } - - /* Now we need to do one last check... If we auto- - * negotiated to HALF DUPLEX, flow control should not be - * enabled per IEEE 802.3 spec. - */ - ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); - if (ret_val) { - DEBUGOUT("Error getting link speed and duplex\n"); - return ret_val; - } - - if (duplex == HALF_DUPLEX) - hw->fc = E1000_FC_NONE; - - /* Now we call a subroutine to actually force the MAC - * controller to use the correct flow control settings. - */ - ret_val = e1000_force_mac_fc(hw); - if (ret_val) { - DEBUGOUT("Error forcing flow control settings\n"); - return ret_val; - } - } else { - DEBUGOUT("Copper PHY and Auto Neg has not completed.\n"); - } - } - return E1000_SUCCESS; + s32 ret_val; + u16 mii_status_reg; + u16 mii_nway_adv_reg; + u16 mii_nway_lp_ability_reg; + u16 speed; + u16 duplex; + + DEBUGFUNC("e1000_config_fc_after_link_up"); + + /* Check for the case where we have fiber media and auto-neg failed + * so we had to force link. In this case, we need to force the + * configuration of the MAC to match the "fc" parameter. + */ + if (((hw->media_type == e1000_media_type_fiber) && (hw->autoneg_failed)) + || ((hw->media_type == e1000_media_type_internal_serdes) + && (hw->autoneg_failed)) + || ((hw->media_type == e1000_media_type_copper) + && (!hw->autoneg))) { + ret_val = e1000_force_mac_fc(hw); + if (ret_val) { + DEBUGOUT("Error forcing flow control settings\n"); + return ret_val; + } + } + + /* Check for the case where we have copper media and auto-neg is + * enabled. In this case, we need to check and see if Auto-Neg + * has completed, and if so, how the PHY and link partner has + * flow control configured. + */ + if ((hw->media_type == e1000_media_type_copper) && hw->autoneg) { + /* Read the MII Status Register and check to see if AutoNeg + * has completed. We read this twice because this reg has + * some "sticky" (latched) bits. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + if (mii_status_reg & MII_SR_AUTONEG_COMPLETE) { + /* The AutoNeg process has completed, so we now need to + * read both the Auto Negotiation Advertisement Register + * (Address 4) and the Auto_Negotiation Base Page Ability + * Register (Address 5) to determine how flow control was + * negotiated. + */ + ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_ADV, + &mii_nway_adv_reg); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, + &mii_nway_lp_ability_reg); + if (ret_val) + return ret_val; + + /* Two bits in the Auto Negotiation Advertisement Register + * (Address 4) and two bits in the Auto Negotiation Base + * Page Ability Register (Address 5) determine flow control + * for both the PHY and the link partner. The following + * table, taken out of the IEEE 802.3ab/D6.0 dated March 25, + * 1999, describes these PAUSE resolution bits and how flow + * control is determined based upon these settings. + * NOTE: DC = Don't Care + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | NIC Resolution + *-------|---------|-------|---------|-------------------- + * 0 | 0 | DC | DC | E1000_FC_NONE + * 0 | 1 | 0 | DC | E1000_FC_NONE + * 0 | 1 | 1 | 0 | E1000_FC_NONE + * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE + * 1 | 0 | 0 | DC | E1000_FC_NONE + * 1 | DC | 1 | DC | E1000_FC_FULL + * 1 | 1 | 0 | 0 | E1000_FC_NONE + * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE + * + */ + /* Are both PAUSE bits set to 1? If so, this implies + * Symmetric Flow Control is enabled at both ends. The + * ASM_DIR bits are irrelevant per the spec. + * + * For Symmetric Flow Control: + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | DC | 1 | DC | E1000_FC_FULL + * + */ + if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE)) { + /* Now we need to check if the user selected RX ONLY + * of pause frames. In this case, we had to advertise + * FULL flow control because we could not advertise RX + * ONLY. Hence, we must now check to see if we need to + * turn OFF the TRANSMISSION of PAUSE frames. + */ + if (hw->original_fc == E1000_FC_FULL) { + hw->fc = E1000_FC_FULL; + DEBUGOUT("Flow Control = FULL.\n"); + } else { + hw->fc = E1000_FC_RX_PAUSE; + DEBUGOUT + ("Flow Control = RX PAUSE frames only.\n"); + } + } + /* For receiving PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 0 | 1 | 1 | 1 | E1000_FC_TX_PAUSE + * + */ + else if (!(mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) + { + hw->fc = E1000_FC_TX_PAUSE; + DEBUGOUT + ("Flow Control = TX PAUSE frames only.\n"); + } + /* For transmitting PAUSE frames ONLY. + * + * LOCAL DEVICE | LINK PARTNER + * PAUSE | ASM_DIR | PAUSE | ASM_DIR | Result + *-------|---------|-------|---------|-------------------- + * 1 | 1 | 0 | 1 | E1000_FC_RX_PAUSE + * + */ + else if ((mii_nway_adv_reg & NWAY_AR_PAUSE) && + (mii_nway_adv_reg & NWAY_AR_ASM_DIR) && + !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) && + (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) + { + hw->fc = E1000_FC_RX_PAUSE; + DEBUGOUT + ("Flow Control = RX PAUSE frames only.\n"); + } + /* Per the IEEE spec, at this point flow control should be + * disabled. However, we want to consider that we could + * be connected to a legacy switch that doesn't advertise + * desired flow control, but can be forced on the link + * partner. So if we advertised no flow control, that is + * what we will resolve to. If we advertised some kind of + * receive capability (Rx Pause Only or Full Flow Control) + * and the link partner advertised none, we will configure + * ourselves to enable Rx Flow Control only. We can do + * this safely for two reasons: If the link partner really + * didn't want flow control enabled, and we enable Rx, no + * harm done since we won't be receiving any PAUSE frames + * anyway. If the intent on the link partner was to have + * flow control enabled, then by us enabling RX only, we + * can at least receive pause frames and process them. + * This is a good idea because in most cases, since we are + * predominantly a server NIC, more times than not we will + * be asked to delay transmission of packets than asking + * our link partner to pause transmission of frames. + */ + else if ((hw->original_fc == E1000_FC_NONE || + hw->original_fc == E1000_FC_TX_PAUSE) || + hw->fc_strict_ieee) { + hw->fc = E1000_FC_NONE; + DEBUGOUT("Flow Control = NONE.\n"); + } else { + hw->fc = E1000_FC_RX_PAUSE; + DEBUGOUT + ("Flow Control = RX PAUSE frames only.\n"); + } + + /* Now we need to do one last check... If we auto- + * negotiated to HALF DUPLEX, flow control should not be + * enabled per IEEE 802.3 spec. + */ + ret_val = + e1000_get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT + ("Error getting link speed and duplex\n"); + return ret_val; + } + + if (duplex == HALF_DUPLEX) + hw->fc = E1000_FC_NONE; + + /* Now we call a subroutine to actually force the MAC + * controller to use the correct flow control settings. + */ + ret_val = e1000_force_mac_fc(hw); + if (ret_val) { + DEBUGOUT + ("Error forcing flow control settings\n"); + return ret_val; + } + } else { + DEBUGOUT + ("Copper PHY and Auto Neg has not completed.\n"); + } + } + return E1000_SUCCESS; } -/****************************************************************************** - * Checks to see if the link status of the hardware has changed. +/** + * e1000_check_for_serdes_link_generic - Check for link (Serdes) + * @hw: pointer to the HW structure * - * hw - Struct containing variables accessed by shared code + * Checks for link up on the hardware. If link is not up and we have + * a signal, then we need to force link up. + */ +static s32 e1000_check_for_serdes_link_generic(struct e1000_hw *hw) +{ + u32 rxcw; + u32 ctrl; + u32 status; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_check_for_serdes_link_generic"); + + ctrl = er32(CTRL); + status = er32(STATUS); + rxcw = er32(RXCW); + + /* + * If we don't have link (auto-negotiation failed or link partner + * cannot auto-negotiate), and our link partner is not trying to + * auto-negotiate with us (we are receiving idles or data), + * we need to force link up. We also need to give auto-negotiation + * time to complete. + */ + /* (ctrl & E1000_CTRL_SWDPIN1) == 1 == have signal */ + if ((!(status & E1000_STATUS_LU)) && (!(rxcw & E1000_RXCW_C))) { + if (hw->autoneg_failed == 0) { + hw->autoneg_failed = 1; + goto out; + } + DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); + + /* Disable auto-negotiation in the TXCW register */ + ew32(TXCW, (hw->txcw & ~E1000_TXCW_ANE)); + + /* Force link-up and also force full-duplex. */ + ctrl = er32(CTRL); + ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); + ew32(CTRL, ctrl); + + /* Configure Flow Control after forcing link up. */ + ret_val = e1000_config_fc_after_link_up(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + goto out; + } + } else if ((ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { + /* + * If we are forcing link and we are receiving /C/ ordered + * sets, re-enable auto-negotiation in the TXCW register + * and disable forced link in the Device Control register + * in an attempt to auto-negotiate with our link partner. + */ + DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); + ew32(TXCW, hw->txcw); + ew32(CTRL, (ctrl & ~E1000_CTRL_SLU)); + + hw->serdes_has_link = true; + } else if (!(E1000_TXCW_ANE & er32(TXCW))) { + /* + * If we force link for non-auto-negotiation switch, check + * link status based on MAC synchronization for internal + * serdes media type. + */ + /* SYNCH bit and IV bit are sticky. */ + udelay(10); + rxcw = er32(RXCW); + if (rxcw & E1000_RXCW_SYNCH) { + if (!(rxcw & E1000_RXCW_IV)) { + hw->serdes_has_link = true; + DEBUGOUT("SERDES: Link up - forced.\n"); + } + } else { + hw->serdes_has_link = false; + DEBUGOUT("SERDES: Link down - force failed.\n"); + } + } + + if (E1000_TXCW_ANE & er32(TXCW)) { + status = er32(STATUS); + if (status & E1000_STATUS_LU) { + /* SYNCH bit and IV bit are sticky, so reread rxcw. */ + udelay(10); + rxcw = er32(RXCW); + if (rxcw & E1000_RXCW_SYNCH) { + if (!(rxcw & E1000_RXCW_IV)) { + hw->serdes_has_link = true; + DEBUGOUT("SERDES: Link up - autoneg " + "completed successfully.\n"); + } else { + hw->serdes_has_link = false; + DEBUGOUT("SERDES: Link down - invalid" + "codewords detected in autoneg.\n"); + } + } else { + hw->serdes_has_link = false; + DEBUGOUT("SERDES: Link down - no sync.\n"); + } + } else { + hw->serdes_has_link = false; + DEBUGOUT("SERDES: Link down - autoneg failed\n"); + } + } + + out: + return ret_val; +} + +/** + * e1000_check_for_link + * @hw: Struct containing variables accessed by shared code * + * Checks to see if the link status of the hardware has changed. * Called by any function that needs to check the link status of the adapter. - *****************************************************************************/ + */ s32 e1000_check_for_link(struct e1000_hw *hw) { - u32 rxcw = 0; - u32 ctrl; - u32 status; - u32 rctl; - u32 icr; - u32 signal = 0; - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_check_for_link"); - - ctrl = er32(CTRL); - status = er32(STATUS); - - /* On adapters with a MAC newer than 82544, SW Defineable pin 1 will be - * set when the optics detect a signal. On older adapters, it will be - * cleared when there is a signal. This applies to fiber media only. - */ - if ((hw->media_type == e1000_media_type_fiber) || - (hw->media_type == e1000_media_type_internal_serdes)) { - rxcw = er32(RXCW); - - if (hw->media_type == e1000_media_type_fiber) { - signal = (hw->mac_type > e1000_82544) ? E1000_CTRL_SWDPIN1 : 0; - if (status & E1000_STATUS_LU) - hw->get_link_status = false; - } - } - - /* If we have a copper PHY then we only want to go out to the PHY - * registers to see if Auto-Neg has completed and/or if our link - * status has changed. The get_link_status flag will be set if we - * receive a Link Status Change interrupt or we have Rx Sequence - * Errors. - */ - if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) { - /* First we want to see if the MII Status Register reports - * link. If so, then we want to get the current speed/duplex - * of the PHY. - * Read the register twice since the link bit is sticky. - */ - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if (phy_data & MII_SR_LINK_STATUS) { - hw->get_link_status = false; - /* Check if there was DownShift, must be checked immediately after - * link-up */ - e1000_check_downshift(hw); - - /* If we are on 82544 or 82543 silicon and speed/duplex - * are forced to 10H or 10F, then we will implement the polarity - * reversal workaround. We disable interrupts first, and upon - * returning, place the devices interrupt state to its previous - * value except for the link status change interrupt which will - * happen due to the execution of this workaround. - */ - - if ((hw->mac_type == e1000_82544 || hw->mac_type == e1000_82543) && - (!hw->autoneg) && - (hw->forced_speed_duplex == e1000_10_full || - hw->forced_speed_duplex == e1000_10_half)) { - ew32(IMC, 0xffffffff); - ret_val = e1000_polarity_reversal_workaround(hw); - icr = er32(ICR); - ew32(ICS, (icr & ~E1000_ICS_LSC)); - ew32(IMS, IMS_ENABLE_MASK); - } - - } else { - /* No link detected */ - e1000_config_dsp_after_link_change(hw, false); - return 0; - } - - /* If we are forcing speed/duplex, then we simply return since - * we have already determined whether we have link or not. - */ - if (!hw->autoneg) return -E1000_ERR_CONFIG; - - /* optimize the dsp settings for the igp phy */ - e1000_config_dsp_after_link_change(hw, true); - - /* We have a M88E1000 PHY and Auto-Neg is enabled. If we - * have Si on board that is 82544 or newer, Auto - * Speed Detection takes care of MAC speed/duplex - * configuration. So we only need to configure Collision - * Distance in the MAC. Otherwise, we need to force - * speed/duplex on the MAC to the current PHY speed/duplex - * settings. - */ - if (hw->mac_type >= e1000_82544) - e1000_config_collision_dist(hw); - else { - ret_val = e1000_config_mac_to_phy(hw); - if (ret_val) { - DEBUGOUT("Error configuring MAC to PHY settings\n"); - return ret_val; - } - } - - /* Configure Flow Control now that Auto-Neg has completed. First, we - * need to restore the desired flow control settings because we may - * have had to re-autoneg with a different link partner. - */ - ret_val = e1000_config_fc_after_link_up(hw); - if (ret_val) { - DEBUGOUT("Error configuring flow control\n"); - return ret_val; - } - - /* At this point we know that we are on copper and we have - * auto-negotiated link. These are conditions for checking the link - * partner capability register. We use the link speed to determine if - * TBI compatibility needs to be turned on or off. If the link is not - * at gigabit speed, then TBI compatibility is not needed. If we are - * at gigabit speed, we turn on TBI compatibility. - */ - if (hw->tbi_compatibility_en) { - u16 speed, duplex; - ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); - if (ret_val) { - DEBUGOUT("Error getting link speed and duplex\n"); - return ret_val; - } - if (speed != SPEED_1000) { - /* If link speed is not set to gigabit speed, we do not need - * to enable TBI compatibility. - */ - if (hw->tbi_compatibility_on) { - /* If we previously were in the mode, turn it off. */ - rctl = er32(RCTL); - rctl &= ~E1000_RCTL_SBP; - ew32(RCTL, rctl); - hw->tbi_compatibility_on = false; - } - } else { - /* If TBI compatibility is was previously off, turn it on. For - * compatibility with a TBI link partner, we will store bad - * packets. Some frames have an additional byte on the end and - * will look like CRC errors to to the hardware. - */ - if (!hw->tbi_compatibility_on) { - hw->tbi_compatibility_on = true; - rctl = er32(RCTL); - rctl |= E1000_RCTL_SBP; - ew32(RCTL, rctl); - } - } - } - } - /* If we don't have link (auto-negotiation failed or link partner cannot - * auto-negotiate), the cable is plugged in (we have signal), and our - * link partner is not trying to auto-negotiate with us (we are receiving - * idles or data), we need to force link up. We also need to give - * auto-negotiation time to complete, in case the cable was just plugged - * in. The autoneg_failed flag does this. - */ - else if ((((hw->media_type == e1000_media_type_fiber) && - ((ctrl & E1000_CTRL_SWDPIN1) == signal)) || - (hw->media_type == e1000_media_type_internal_serdes)) && - (!(status & E1000_STATUS_LU)) && - (!(rxcw & E1000_RXCW_C))) { - if (hw->autoneg_failed == 0) { - hw->autoneg_failed = 1; - return 0; - } - DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n"); - - /* Disable auto-negotiation in the TXCW register */ - ew32(TXCW, (hw->txcw & ~E1000_TXCW_ANE)); - - /* Force link-up and also force full-duplex. */ - ctrl = er32(CTRL); - ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD); - ew32(CTRL, ctrl); - - /* Configure Flow Control after forcing link up. */ - ret_val = e1000_config_fc_after_link_up(hw); - if (ret_val) { - DEBUGOUT("Error configuring flow control\n"); - return ret_val; - } - } - /* If we are forcing link and we are receiving /C/ ordered sets, re-enable - * auto-negotiation in the TXCW register and disable forced link in the - * Device Control register in an attempt to auto-negotiate with our link - * partner. - */ - else if (((hw->media_type == e1000_media_type_fiber) || - (hw->media_type == e1000_media_type_internal_serdes)) && - (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) { - DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n"); - ew32(TXCW, hw->txcw); - ew32(CTRL, (ctrl & ~E1000_CTRL_SLU)); - - hw->serdes_link_down = false; - } - /* If we force link for non-auto-negotiation switch, check link status - * based on MAC synchronization for internal serdes media type. - */ - else if ((hw->media_type == e1000_media_type_internal_serdes) && - !(E1000_TXCW_ANE & er32(TXCW))) { - /* SYNCH bit and IV bit are sticky. */ - udelay(10); - if (E1000_RXCW_SYNCH & er32(RXCW)) { - if (!(rxcw & E1000_RXCW_IV)) { - hw->serdes_link_down = false; - DEBUGOUT("SERDES: Link is up.\n"); - } - } else { - hw->serdes_link_down = true; - DEBUGOUT("SERDES: Link is down.\n"); - } - } - if ((hw->media_type == e1000_media_type_internal_serdes) && - (E1000_TXCW_ANE & er32(TXCW))) { - hw->serdes_link_down = !(E1000_STATUS_LU & er32(STATUS)); - } - return E1000_SUCCESS; + u32 rxcw = 0; + u32 ctrl; + u32 status; + u32 rctl; + u32 icr; + u32 signal = 0; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_check_for_link"); + + ctrl = er32(CTRL); + status = er32(STATUS); + + /* On adapters with a MAC newer than 82544, SW Definable pin 1 will be + * set when the optics detect a signal. On older adapters, it will be + * cleared when there is a signal. This applies to fiber media only. + */ + if ((hw->media_type == e1000_media_type_fiber) || + (hw->media_type == e1000_media_type_internal_serdes)) { + rxcw = er32(RXCW); + + if (hw->media_type == e1000_media_type_fiber) { + signal = + (hw->mac_type > + e1000_82544) ? E1000_CTRL_SWDPIN1 : 0; + if (status & E1000_STATUS_LU) + hw->get_link_status = false; + } + } + + /* If we have a copper PHY then we only want to go out to the PHY + * registers to see if Auto-Neg has completed and/or if our link + * status has changed. The get_link_status flag will be set if we + * receive a Link Status Change interrupt or we have Rx Sequence + * Errors. + */ + if ((hw->media_type == e1000_media_type_copper) && hw->get_link_status) { + /* First we want to see if the MII Status Register reports + * link. If so, then we want to get the current speed/duplex + * of the PHY. + * Read the register twice since the link bit is sticky. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if (phy_data & MII_SR_LINK_STATUS) { + hw->get_link_status = false; + /* Check if there was DownShift, must be checked immediately after + * link-up */ + e1000_check_downshift(hw); + + /* If we are on 82544 or 82543 silicon and speed/duplex + * are forced to 10H or 10F, then we will implement the polarity + * reversal workaround. We disable interrupts first, and upon + * returning, place the devices interrupt state to its previous + * value except for the link status change interrupt which will + * happen due to the execution of this workaround. + */ + + if ((hw->mac_type == e1000_82544 + || hw->mac_type == e1000_82543) && (!hw->autoneg) + && (hw->forced_speed_duplex == e1000_10_full + || hw->forced_speed_duplex == e1000_10_half)) { + ew32(IMC, 0xffffffff); + ret_val = + e1000_polarity_reversal_workaround(hw); + icr = er32(ICR); + ew32(ICS, (icr & ~E1000_ICS_LSC)); + ew32(IMS, IMS_ENABLE_MASK); + } + + } else { + /* No link detected */ + e1000_config_dsp_after_link_change(hw, false); + return 0; + } + + /* If we are forcing speed/duplex, then we simply return since + * we have already determined whether we have link or not. + */ + if (!hw->autoneg) + return -E1000_ERR_CONFIG; + + /* optimize the dsp settings for the igp phy */ + e1000_config_dsp_after_link_change(hw, true); + + /* We have a M88E1000 PHY and Auto-Neg is enabled. If we + * have Si on board that is 82544 or newer, Auto + * Speed Detection takes care of MAC speed/duplex + * configuration. So we only need to configure Collision + * Distance in the MAC. Otherwise, we need to force + * speed/duplex on the MAC to the current PHY speed/duplex + * settings. + */ + if (hw->mac_type >= e1000_82544) + e1000_config_collision_dist(hw); + else { + ret_val = e1000_config_mac_to_phy(hw); + if (ret_val) { + DEBUGOUT + ("Error configuring MAC to PHY settings\n"); + return ret_val; + } + } + + /* Configure Flow Control now that Auto-Neg has completed. First, we + * need to restore the desired flow control settings because we may + * have had to re-autoneg with a different link partner. + */ + ret_val = e1000_config_fc_after_link_up(hw); + if (ret_val) { + DEBUGOUT("Error configuring flow control\n"); + return ret_val; + } + + /* At this point we know that we are on copper and we have + * auto-negotiated link. These are conditions for checking the link + * partner capability register. We use the link speed to determine if + * TBI compatibility needs to be turned on or off. If the link is not + * at gigabit speed, then TBI compatibility is not needed. If we are + * at gigabit speed, we turn on TBI compatibility. + */ + if (hw->tbi_compatibility_en) { + u16 speed, duplex; + ret_val = + e1000_get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT + ("Error getting link speed and duplex\n"); + return ret_val; + } + if (speed != SPEED_1000) { + /* If link speed is not set to gigabit speed, we do not need + * to enable TBI compatibility. + */ + if (hw->tbi_compatibility_on) { + /* If we previously were in the mode, turn it off. */ + rctl = er32(RCTL); + rctl &= ~E1000_RCTL_SBP; + ew32(RCTL, rctl); + hw->tbi_compatibility_on = false; + } + } else { + /* If TBI compatibility is was previously off, turn it on. For + * compatibility with a TBI link partner, we will store bad + * packets. Some frames have an additional byte on the end and + * will look like CRC errors to to the hardware. + */ + if (!hw->tbi_compatibility_on) { + hw->tbi_compatibility_on = true; + rctl = er32(RCTL); + rctl |= E1000_RCTL_SBP; + ew32(RCTL, rctl); + } + } + } + } + + if ((hw->media_type == e1000_media_type_fiber) || + (hw->media_type == e1000_media_type_internal_serdes)) + e1000_check_for_serdes_link_generic(hw); + + return E1000_SUCCESS; } -/****************************************************************************** +/** + * e1000_get_speed_and_duplex + * @hw: Struct containing variables accessed by shared code + * @speed: Speed of the connection + * @duplex: Duplex setting of the connection + * Detects the current speed and duplex settings of the hardware. - * - * hw - Struct containing variables accessed by shared code - * speed - Speed of the connection - * duplex - Duplex setting of the connection - *****************************************************************************/ + */ s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex) { - u32 status; - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_get_speed_and_duplex"); - - if (hw->mac_type >= e1000_82543) { - status = er32(STATUS); - if (status & E1000_STATUS_SPEED_1000) { - *speed = SPEED_1000; - DEBUGOUT("1000 Mbs, "); - } else if (status & E1000_STATUS_SPEED_100) { - *speed = SPEED_100; - DEBUGOUT("100 Mbs, "); - } else { - *speed = SPEED_10; - DEBUGOUT("10 Mbs, "); - } - - if (status & E1000_STATUS_FD) { - *duplex = FULL_DUPLEX; - DEBUGOUT("Full Duplex\n"); - } else { - *duplex = HALF_DUPLEX; - DEBUGOUT(" Half Duplex\n"); - } - } else { - DEBUGOUT("1000 Mbs, Full Duplex\n"); - *speed = SPEED_1000; - *duplex = FULL_DUPLEX; - } - - /* IGP01 PHY may advertise full duplex operation after speed downgrade even - * if it is operating at half duplex. Here we set the duplex settings to - * match the duplex in the link partner's capabilities. - */ - if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) { - ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); - if (ret_val) - return ret_val; - - if (!(phy_data & NWAY_ER_LP_NWAY_CAPS)) - *duplex = HALF_DUPLEX; - else { - ret_val = e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data); - if (ret_val) - return ret_val; - if ((*speed == SPEED_100 && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) || - (*speed == SPEED_10 && !(phy_data & NWAY_LPAR_10T_FD_CAPS))) - *duplex = HALF_DUPLEX; - } - } - - if ((hw->mac_type == e1000_80003es2lan) && - (hw->media_type == e1000_media_type_copper)) { - if (*speed == SPEED_1000) - ret_val = e1000_configure_kmrn_for_1000(hw); - else - ret_val = e1000_configure_kmrn_for_10_100(hw, *duplex); - if (ret_val) - return ret_val; - } - - if ((hw->phy_type == e1000_phy_igp_3) && (*speed == SPEED_1000)) { - ret_val = e1000_kumeran_lock_loss_workaround(hw); - if (ret_val) - return ret_val; - } - - return E1000_SUCCESS; + u32 status; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_get_speed_and_duplex"); + + if (hw->mac_type >= e1000_82543) { + status = er32(STATUS); + if (status & E1000_STATUS_SPEED_1000) { + *speed = SPEED_1000; + DEBUGOUT("1000 Mbs, "); + } else if (status & E1000_STATUS_SPEED_100) { + *speed = SPEED_100; + DEBUGOUT("100 Mbs, "); + } else { + *speed = SPEED_10; + DEBUGOUT("10 Mbs, "); + } + + if (status & E1000_STATUS_FD) { + *duplex = FULL_DUPLEX; + DEBUGOUT("Full Duplex\n"); + } else { + *duplex = HALF_DUPLEX; + DEBUGOUT(" Half Duplex\n"); + } + } else { + DEBUGOUT("1000 Mbs, Full Duplex\n"); + *speed = SPEED_1000; + *duplex = FULL_DUPLEX; + } + + /* IGP01 PHY may advertise full duplex operation after speed downgrade even + * if it is operating at half duplex. Here we set the duplex settings to + * match the duplex in the link partner's capabilities. + */ + if (hw->phy_type == e1000_phy_igp && hw->speed_downgraded) { + ret_val = e1000_read_phy_reg(hw, PHY_AUTONEG_EXP, &phy_data); + if (ret_val) + return ret_val; + + if (!(phy_data & NWAY_ER_LP_NWAY_CAPS)) + *duplex = HALF_DUPLEX; + else { + ret_val = + e1000_read_phy_reg(hw, PHY_LP_ABILITY, &phy_data); + if (ret_val) + return ret_val; + if ((*speed == SPEED_100 + && !(phy_data & NWAY_LPAR_100TX_FD_CAPS)) + || (*speed == SPEED_10 + && !(phy_data & NWAY_LPAR_10T_FD_CAPS))) + *duplex = HALF_DUPLEX; + } + } + + return E1000_SUCCESS; } -/****************************************************************************** -* Blocks until autoneg completes or times out (~4.5 seconds) -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ +/** + * e1000_wait_autoneg + * @hw: Struct containing variables accessed by shared code + * + * Blocks until autoneg completes or times out (~4.5 seconds) + */ static s32 e1000_wait_autoneg(struct e1000_hw *hw) { - s32 ret_val; - u16 i; - u16 phy_data; - - DEBUGFUNC("e1000_wait_autoneg"); - DEBUGOUT("Waiting for Auto-Neg to complete.\n"); - - /* We will wait for autoneg to complete or 4.5 seconds to expire. */ - for (i = PHY_AUTO_NEG_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Auto-Neg - * Complete bit to be set. - */ - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - if (phy_data & MII_SR_AUTONEG_COMPLETE) { - return E1000_SUCCESS; - } - msleep(100); - } - return E1000_SUCCESS; + s32 ret_val; + u16 i; + u16 phy_data; + + DEBUGFUNC("e1000_wait_autoneg"); + DEBUGOUT("Waiting for Auto-Neg to complete.\n"); + + /* We will wait for autoneg to complete or 4.5 seconds to expire. */ + for (i = PHY_AUTO_NEG_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Auto-Neg + * Complete bit to be set. + */ + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + if (phy_data & MII_SR_AUTONEG_COMPLETE) { + return E1000_SUCCESS; + } + msleep(100); + } + return E1000_SUCCESS; } -/****************************************************************************** -* Raises the Management Data Clock -* -* hw - Struct containing variables accessed by shared code -* ctrl - Device control register's current value -******************************************************************************/ +/** + * e1000_raise_mdi_clk - Raises the Management Data Clock + * @hw: Struct containing variables accessed by shared code + * @ctrl: Device control register's current value + */ static void e1000_raise_mdi_clk(struct e1000_hw *hw, u32 *ctrl) { - /* Raise the clock input to the Management Data Clock (by setting the MDC - * bit), and then delay 10 microseconds. - */ - ew32(CTRL, (*ctrl | E1000_CTRL_MDC)); - E1000_WRITE_FLUSH(); - udelay(10); + /* Raise the clock input to the Management Data Clock (by setting the MDC + * bit), and then delay 10 microseconds. + */ + ew32(CTRL, (*ctrl | E1000_CTRL_MDC)); + E1000_WRITE_FLUSH(); + udelay(10); } -/****************************************************************************** -* Lowers the Management Data Clock -* -* hw - Struct containing variables accessed by shared code -* ctrl - Device control register's current value -******************************************************************************/ +/** + * e1000_lower_mdi_clk - Lowers the Management Data Clock + * @hw: Struct containing variables accessed by shared code + * @ctrl: Device control register's current value + */ static void e1000_lower_mdi_clk(struct e1000_hw *hw, u32 *ctrl) { - /* Lower the clock input to the Management Data Clock (by clearing the MDC - * bit), and then delay 10 microseconds. - */ - ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC)); - E1000_WRITE_FLUSH(); - udelay(10); + /* Lower the clock input to the Management Data Clock (by clearing the MDC + * bit), and then delay 10 microseconds. + */ + ew32(CTRL, (*ctrl & ~E1000_CTRL_MDC)); + E1000_WRITE_FLUSH(); + udelay(10); } -/****************************************************************************** -* Shifts data bits out to the PHY -* -* hw - Struct containing variables accessed by shared code -* data - Data to send out to the PHY -* count - Number of bits to shift out -* -* Bits are shifted out in MSB to LSB order. -******************************************************************************/ +/** + * e1000_shift_out_mdi_bits - Shifts data bits out to the PHY + * @hw: Struct containing variables accessed by shared code + * @data: Data to send out to the PHY + * @count: Number of bits to shift out + * + * Bits are shifted out in MSB to LSB order. + */ static void e1000_shift_out_mdi_bits(struct e1000_hw *hw, u32 data, u16 count) { - u32 ctrl; - u32 mask; - - /* We need to shift "count" number of bits out to the PHY. So, the value - * in the "data" parameter will be shifted out to the PHY one bit at a - * time. In order to do this, "data" must be broken down into bits. - */ - mask = 0x01; - mask <<= (count - 1); - - ctrl = er32(CTRL); - - /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ - ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); - - while (mask) { - /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and - * then raising and lowering the Management Data Clock. A "0" is - * shifted out to the PHY by setting the MDIO bit to "0" and then - * raising and lowering the clock. - */ - if (data & mask) - ctrl |= E1000_CTRL_MDIO; - else - ctrl &= ~E1000_CTRL_MDIO; - - ew32(CTRL, ctrl); - E1000_WRITE_FLUSH(); - - udelay(10); - - e1000_raise_mdi_clk(hw, &ctrl); - e1000_lower_mdi_clk(hw, &ctrl); - - mask = mask >> 1; - } -} - -/****************************************************************************** -* Shifts data bits in from the PHY -* -* hw - Struct containing variables accessed by shared code -* -* Bits are shifted in in MSB to LSB order. -******************************************************************************/ -static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw) -{ - u32 ctrl; - u16 data = 0; - u8 i; - - /* In order to read a register from the PHY, we need to shift in a total - * of 18 bits from the PHY. The first two bit (turnaround) times are used - * to avoid contention on the MDIO pin when a read operation is performed. - * These two bits are ignored by us and thrown away. Bits are "shifted in" - * by raising the input to the Management Data Clock (setting the MDC bit), - * and then reading the value of the MDIO bit. - */ - ctrl = er32(CTRL); - - /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ - ctrl &= ~E1000_CTRL_MDIO_DIR; - ctrl &= ~E1000_CTRL_MDIO; - - ew32(CTRL, ctrl); - E1000_WRITE_FLUSH(); - - /* Raise and Lower the clock before reading in the data. This accounts for - * the turnaround bits. The first clock occurred when we clocked out the - * last bit of the Register Address. - */ - e1000_raise_mdi_clk(hw, &ctrl); - e1000_lower_mdi_clk(hw, &ctrl); - - for (data = 0, i = 0; i < 16; i++) { - data = data << 1; - e1000_raise_mdi_clk(hw, &ctrl); - ctrl = er32(CTRL); - /* Check to see if we shifted in a "1". */ - if (ctrl & E1000_CTRL_MDIO) - data |= 1; - e1000_lower_mdi_clk(hw, &ctrl); - } - - e1000_raise_mdi_clk(hw, &ctrl); - e1000_lower_mdi_clk(hw, &ctrl); - - return data; -} - -static s32 e1000_swfw_sync_acquire(struct e1000_hw *hw, u16 mask) -{ - u32 swfw_sync = 0; - u32 swmask = mask; - u32 fwmask = mask << 16; - s32 timeout = 200; + u32 ctrl; + u32 mask; - DEBUGFUNC("e1000_swfw_sync_acquire"); - - if (hw->swfwhw_semaphore_present) - return e1000_get_software_flag(hw); + /* We need to shift "count" number of bits out to the PHY. So, the value + * in the "data" parameter will be shifted out to the PHY one bit at a + * time. In order to do this, "data" must be broken down into bits. + */ + mask = 0x01; + mask <<= (count - 1); - if (!hw->swfw_sync_present) - return e1000_get_hw_eeprom_semaphore(hw); + ctrl = er32(CTRL); - while (timeout) { - if (e1000_get_hw_eeprom_semaphore(hw)) - return -E1000_ERR_SWFW_SYNC; + /* Set MDIO_DIR and MDC_DIR direction bits to be used as output pins. */ + ctrl |= (E1000_CTRL_MDIO_DIR | E1000_CTRL_MDC_DIR); - swfw_sync = er32(SW_FW_SYNC); - if (!(swfw_sync & (fwmask | swmask))) { - break; - } + while (mask) { + /* A "1" is shifted out to the PHY by setting the MDIO bit to "1" and + * then raising and lowering the Management Data Clock. A "0" is + * shifted out to the PHY by setting the MDIO bit to "0" and then + * raising and lowering the clock. + */ + if (data & mask) + ctrl |= E1000_CTRL_MDIO; + else + ctrl &= ~E1000_CTRL_MDIO; - /* firmware currently using resource (fwmask) */ - /* or other software thread currently using resource (swmask) */ - e1000_put_hw_eeprom_semaphore(hw); - mdelay(5); - timeout--; - } + ew32(CTRL, ctrl); + E1000_WRITE_FLUSH(); - if (!timeout) { - DEBUGOUT("Driver can't access resource, SW_FW_SYNC timeout.\n"); - return -E1000_ERR_SWFW_SYNC; - } + udelay(10); - swfw_sync |= swmask; - ew32(SW_FW_SYNC, swfw_sync); + e1000_raise_mdi_clk(hw, &ctrl); + e1000_lower_mdi_clk(hw, &ctrl); - e1000_put_hw_eeprom_semaphore(hw); - return E1000_SUCCESS; + mask = mask >> 1; + } } -static void e1000_swfw_sync_release(struct e1000_hw *hw, u16 mask) +/** + * e1000_shift_in_mdi_bits - Shifts data bits in from the PHY + * @hw: Struct containing variables accessed by shared code + * + * Bits are shifted in in MSB to LSB order. + */ +static u16 e1000_shift_in_mdi_bits(struct e1000_hw *hw) { - u32 swfw_sync; - u32 swmask = mask; + u32 ctrl; + u16 data = 0; + u8 i; - DEBUGFUNC("e1000_swfw_sync_release"); + /* In order to read a register from the PHY, we need to shift in a total + * of 18 bits from the PHY. The first two bit (turnaround) times are used + * to avoid contention on the MDIO pin when a read operation is performed. + * These two bits are ignored by us and thrown away. Bits are "shifted in" + * by raising the input to the Management Data Clock (setting the MDC bit), + * and then reading the value of the MDIO bit. + */ + ctrl = er32(CTRL); - if (hw->swfwhw_semaphore_present) { - e1000_release_software_flag(hw); - return; - } + /* Clear MDIO_DIR (SWDPIO1) to indicate this bit is to be used as input. */ + ctrl &= ~E1000_CTRL_MDIO_DIR; + ctrl &= ~E1000_CTRL_MDIO; - if (!hw->swfw_sync_present) { - e1000_put_hw_eeprom_semaphore(hw); - return; - } + ew32(CTRL, ctrl); + E1000_WRITE_FLUSH(); - /* if (e1000_get_hw_eeprom_semaphore(hw)) - * return -E1000_ERR_SWFW_SYNC; */ - while (e1000_get_hw_eeprom_semaphore(hw) != E1000_SUCCESS); - /* empty */ + /* Raise and Lower the clock before reading in the data. This accounts for + * the turnaround bits. The first clock occurred when we clocked out the + * last bit of the Register Address. + */ + e1000_raise_mdi_clk(hw, &ctrl); + e1000_lower_mdi_clk(hw, &ctrl); + + for (data = 0, i = 0; i < 16; i++) { + data = data << 1; + e1000_raise_mdi_clk(hw, &ctrl); + ctrl = er32(CTRL); + /* Check to see if we shifted in a "1". */ + if (ctrl & E1000_CTRL_MDIO) + data |= 1; + e1000_lower_mdi_clk(hw, &ctrl); + } - swfw_sync = er32(SW_FW_SYNC); - swfw_sync &= ~swmask; - ew32(SW_FW_SYNC, swfw_sync); + e1000_raise_mdi_clk(hw, &ctrl); + e1000_lower_mdi_clk(hw, &ctrl); - e1000_put_hw_eeprom_semaphore(hw); + return data; } -/***************************************************************************** -* Reads the value from a PHY register, if the value is on a specific non zero -* page, sets the page first. -* hw - Struct containing variables accessed by shared code -* reg_addr - address of the PHY register to read -******************************************************************************/ + +/** + * e1000_read_phy_reg - read a phy register + * @hw: Struct containing variables accessed by shared code + * @reg_addr: address of the PHY register to read + * + * Reads the value from a PHY register, if the value is on a specific non zero + * page, sets the page first. + */ s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data) { - u32 ret_val; - u16 swfw; - - DEBUGFUNC("e1000_read_phy_reg"); - - if ((hw->mac_type == e1000_80003es2lan) && - (er32(STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (e1000_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - if ((hw->phy_type == e1000_phy_igp || - hw->phy_type == e1000_phy_igp_3 || - hw->phy_type == e1000_phy_igp_2) && - (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { - ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, - (u16)reg_addr); - if (ret_val) { - e1000_swfw_sync_release(hw, swfw); - return ret_val; - } - } else if (hw->phy_type == e1000_phy_gg82563) { - if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || - (hw->mac_type == e1000_80003es2lan)) { - /* Select Configuration Page */ - if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { - ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, - (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT)); - } else { - /* Use Alternative Page Select register to access - * registers 30 and 31 - */ - ret_val = e1000_write_phy_reg_ex(hw, - GG82563_PHY_PAGE_SELECT_ALT, - (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT)); - } - - if (ret_val) { - e1000_swfw_sync_release(hw, swfw); - return ret_val; - } - } - } - - ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, - phy_data); - - e1000_swfw_sync_release(hw, swfw); - return ret_val; + u32 ret_val; + + DEBUGFUNC("e1000_read_phy_reg"); + + if ((hw->phy_type == e1000_phy_igp) && + (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { + ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, + (u16) reg_addr); + if (ret_val) + return ret_val; + } + + ret_val = e1000_read_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, + phy_data); + + return ret_val; } static s32 e1000_read_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data) { - u32 i; - u32 mdic = 0; - const u32 phy_addr = 1; - - DEBUGFUNC("e1000_read_phy_reg_ex"); - - if (reg_addr > MAX_PHY_REG_ADDRESS) { - DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); - return -E1000_ERR_PARAM; - } - - if (hw->mac_type > e1000_82543) { - /* Set up Op-code, Phy Address, and register address in the MDI - * Control register. The MAC will take care of interfacing with the - * PHY to retrieve the desired data. - */ - mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | - (phy_addr << E1000_MDIC_PHY_SHIFT) | - (E1000_MDIC_OP_READ)); - - ew32(MDIC, mdic); - - /* Poll the ready bit to see if the MDI read completed */ - for (i = 0; i < 64; i++) { - udelay(50); - mdic = er32(MDIC); - if (mdic & E1000_MDIC_READY) break; - } - if (!(mdic & E1000_MDIC_READY)) { - DEBUGOUT("MDI Read did not complete\n"); - return -E1000_ERR_PHY; - } - if (mdic & E1000_MDIC_ERROR) { - DEBUGOUT("MDI Error\n"); - return -E1000_ERR_PHY; - } - *phy_data = (u16)mdic; - } else { - /* We must first send a preamble through the MDIO pin to signal the - * beginning of an MII instruction. This is done by sending 32 - * consecutive "1" bits. - */ - e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); - - /* Now combine the next few fields that are required for a read - * operation. We use this method instead of calling the - * e1000_shift_out_mdi_bits routine five different times. The format of - * a MII read instruction consists of a shift out of 14 bits and is - * defined as follows: - * <Preamble><SOF><Op Code><Phy Addr><Reg Addr> - * followed by a shift in of 18 bits. This first two bits shifted in - * are TurnAround bits used to avoid contention on the MDIO pin when a - * READ operation is performed. These two bits are thrown away - * followed by a shift in of 16 bits which contains the desired data. - */ - mdic = ((reg_addr) | (phy_addr << 5) | - (PHY_OP_READ << 10) | (PHY_SOF << 12)); - - e1000_shift_out_mdi_bits(hw, mdic, 14); - - /* Now that we've shifted out the read command to the MII, we need to - * "shift in" the 16-bit value (18 total bits) of the requested PHY - * register address. - */ - *phy_data = e1000_shift_in_mdi_bits(hw); - } - return E1000_SUCCESS; + u32 i; + u32 mdic = 0; + const u32 phy_addr = 1; + + DEBUGFUNC("e1000_read_phy_reg_ex"); + + if (reg_addr > MAX_PHY_REG_ADDRESS) { + DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); + return -E1000_ERR_PARAM; + } + + if (hw->mac_type > e1000_82543) { + /* Set up Op-code, Phy Address, and register address in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + mdic = ((reg_addr << E1000_MDIC_REG_SHIFT) | + (phy_addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_READ)); + + ew32(MDIC, mdic); + + /* Poll the ready bit to see if the MDI read completed */ + for (i = 0; i < 64; i++) { + udelay(50); + mdic = er32(MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + DEBUGOUT("MDI Read did not complete\n"); + return -E1000_ERR_PHY; + } + if (mdic & E1000_MDIC_ERROR) { + DEBUGOUT("MDI Error\n"); + return -E1000_ERR_PHY; + } + *phy_data = (u16) mdic; + } else { + /* We must first send a preamble through the MDIO pin to signal the + * beginning of an MII instruction. This is done by sending 32 + * consecutive "1" bits. + */ + e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); + + /* Now combine the next few fields that are required for a read + * operation. We use this method instead of calling the + * e1000_shift_out_mdi_bits routine five different times. The format of + * a MII read instruction consists of a shift out of 14 bits and is + * defined as follows: + * <Preamble><SOF><Op Code><Phy Addr><Reg Addr> + * followed by a shift in of 18 bits. This first two bits shifted in + * are TurnAround bits used to avoid contention on the MDIO pin when a + * READ operation is performed. These two bits are thrown away + * followed by a shift in of 16 bits which contains the desired data. + */ + mdic = ((reg_addr) | (phy_addr << 5) | + (PHY_OP_READ << 10) | (PHY_SOF << 12)); + + e1000_shift_out_mdi_bits(hw, mdic, 14); + + /* Now that we've shifted out the read command to the MII, we need to + * "shift in" the 16-bit value (18 total bits) of the requested PHY + * register address. + */ + *phy_data = e1000_shift_in_mdi_bits(hw); + } + return E1000_SUCCESS; } -/****************************************************************************** -* Writes a value to a PHY register -* -* hw - Struct containing variables accessed by shared code -* reg_addr - address of the PHY register to write -* data - data to write to the PHY -******************************************************************************/ +/** + * e1000_write_phy_reg - write a phy register + * + * @hw: Struct containing variables accessed by shared code + * @reg_addr: address of the PHY register to write + * @data: data to write to the PHY + + * Writes a value to a PHY register + */ s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 phy_data) { - u32 ret_val; - u16 swfw; - - DEBUGFUNC("e1000_write_phy_reg"); - - if ((hw->mac_type == e1000_80003es2lan) && - (er32(STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (e1000_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - if ((hw->phy_type == e1000_phy_igp || - hw->phy_type == e1000_phy_igp_3 || - hw->phy_type == e1000_phy_igp_2) && - (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { - ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, - (u16)reg_addr); - if (ret_val) { - e1000_swfw_sync_release(hw, swfw); - return ret_val; - } - } else if (hw->phy_type == e1000_phy_gg82563) { - if (((reg_addr & MAX_PHY_REG_ADDRESS) > MAX_PHY_MULTI_PAGE_REG) || - (hw->mac_type == e1000_80003es2lan)) { - /* Select Configuration Page */ - if ((reg_addr & MAX_PHY_REG_ADDRESS) < GG82563_MIN_ALT_REG) { - ret_val = e1000_write_phy_reg_ex(hw, GG82563_PHY_PAGE_SELECT, - (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT)); - } else { - /* Use Alternative Page Select register to access - * registers 30 and 31 - */ - ret_val = e1000_write_phy_reg_ex(hw, - GG82563_PHY_PAGE_SELECT_ALT, - (u16)((u16)reg_addr >> GG82563_PAGE_SHIFT)); - } - - if (ret_val) { - e1000_swfw_sync_release(hw, swfw); - return ret_val; - } - } - } - - ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, - phy_data); - - e1000_swfw_sync_release(hw, swfw); - return ret_val; + u32 ret_val; + + DEBUGFUNC("e1000_write_phy_reg"); + + if ((hw->phy_type == e1000_phy_igp) && + (reg_addr > MAX_PHY_MULTI_PAGE_REG)) { + ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT, + (u16) reg_addr); + if (ret_val) + return ret_val; + } + + ret_val = e1000_write_phy_reg_ex(hw, MAX_PHY_REG_ADDRESS & reg_addr, + phy_data); + + return ret_val; } static s32 e1000_write_phy_reg_ex(struct e1000_hw *hw, u32 reg_addr, u16 phy_data) { - u32 i; - u32 mdic = 0; - const u32 phy_addr = 1; - - DEBUGFUNC("e1000_write_phy_reg_ex"); - - if (reg_addr > MAX_PHY_REG_ADDRESS) { - DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); - return -E1000_ERR_PARAM; - } - - if (hw->mac_type > e1000_82543) { - /* Set up Op-code, Phy Address, register address, and data intended - * for the PHY register in the MDI Control register. The MAC will take - * care of interfacing with the PHY to send the desired data. - */ - mdic = (((u32)phy_data) | - (reg_addr << E1000_MDIC_REG_SHIFT) | - (phy_addr << E1000_MDIC_PHY_SHIFT) | - (E1000_MDIC_OP_WRITE)); - - ew32(MDIC, mdic); - - /* Poll the ready bit to see if the MDI read completed */ - for (i = 0; i < 641; i++) { - udelay(5); - mdic = er32(MDIC); - if (mdic & E1000_MDIC_READY) break; - } - if (!(mdic & E1000_MDIC_READY)) { - DEBUGOUT("MDI Write did not complete\n"); - return -E1000_ERR_PHY; - } - } else { - /* We'll need to use the SW defined pins to shift the write command - * out to the PHY. We first send a preamble to the PHY to signal the - * beginning of the MII instruction. This is done by sending 32 - * consecutive "1" bits. - */ - e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); - - /* Now combine the remaining required fields that will indicate a - * write operation. We use this method instead of calling the - * e1000_shift_out_mdi_bits routine for each field in the command. The - * format of a MII write instruction is as follows: - * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>. - */ - mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | - (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); - mdic <<= 16; - mdic |= (u32)phy_data; - - e1000_shift_out_mdi_bits(hw, mdic, 32); - } - - return E1000_SUCCESS; -} + u32 i; + u32 mdic = 0; + const u32 phy_addr = 1; -static s32 e1000_read_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 *data) -{ - u32 reg_val; - u16 swfw; - DEBUGFUNC("e1000_read_kmrn_reg"); - - if ((hw->mac_type == e1000_80003es2lan) && - (er32(STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (e1000_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - /* Write register address */ - reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & - E1000_KUMCTRLSTA_OFFSET) | - E1000_KUMCTRLSTA_REN; - ew32(KUMCTRLSTA, reg_val); - udelay(2); - - /* Read the data returned */ - reg_val = er32(KUMCTRLSTA); - *data = (u16)reg_val; - - e1000_swfw_sync_release(hw, swfw); - return E1000_SUCCESS; -} + DEBUGFUNC("e1000_write_phy_reg_ex"); -static s32 e1000_write_kmrn_reg(struct e1000_hw *hw, u32 reg_addr, u16 data) -{ - u32 reg_val; - u16 swfw; - DEBUGFUNC("e1000_write_kmrn_reg"); - - if ((hw->mac_type == e1000_80003es2lan) && - (er32(STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (e1000_swfw_sync_acquire(hw, swfw)) - return -E1000_ERR_SWFW_SYNC; - - reg_val = ((reg_addr << E1000_KUMCTRLSTA_OFFSET_SHIFT) & - E1000_KUMCTRLSTA_OFFSET) | data; - ew32(KUMCTRLSTA, reg_val); - udelay(2); - - e1000_swfw_sync_release(hw, swfw); - return E1000_SUCCESS; + if (reg_addr > MAX_PHY_REG_ADDRESS) { + DEBUGOUT1("PHY Address %d is out of range\n", reg_addr); + return -E1000_ERR_PARAM; + } + + if (hw->mac_type > e1000_82543) { + /* Set up Op-code, Phy Address, register address, and data intended + * for the PHY register in the MDI Control register. The MAC will take + * care of interfacing with the PHY to send the desired data. + */ + mdic = (((u32) phy_data) | + (reg_addr << E1000_MDIC_REG_SHIFT) | + (phy_addr << E1000_MDIC_PHY_SHIFT) | + (E1000_MDIC_OP_WRITE)); + + ew32(MDIC, mdic); + + /* Poll the ready bit to see if the MDI read completed */ + for (i = 0; i < 641; i++) { + udelay(5); + mdic = er32(MDIC); + if (mdic & E1000_MDIC_READY) + break; + } + if (!(mdic & E1000_MDIC_READY)) { + DEBUGOUT("MDI Write did not complete\n"); + return -E1000_ERR_PHY; + } + } else { + /* We'll need to use the SW defined pins to shift the write command + * out to the PHY. We first send a preamble to the PHY to signal the + * beginning of the MII instruction. This is done by sending 32 + * consecutive "1" bits. + */ + e1000_shift_out_mdi_bits(hw, PHY_PREAMBLE, PHY_PREAMBLE_SIZE); + + /* Now combine the remaining required fields that will indicate a + * write operation. We use this method instead of calling the + * e1000_shift_out_mdi_bits routine for each field in the command. The + * format of a MII write instruction is as follows: + * <Preamble><SOF><Op Code><Phy Addr><Reg Addr><Turnaround><Data>. + */ + mdic = ((PHY_TURNAROUND) | (reg_addr << 2) | (phy_addr << 7) | + (PHY_OP_WRITE << 12) | (PHY_SOF << 14)); + mdic <<= 16; + mdic |= (u32) phy_data; + + e1000_shift_out_mdi_bits(hw, mdic, 32); + } + + return E1000_SUCCESS; } -/****************************************************************************** -* Returns the PHY to the power-on reset state -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ +/** + * e1000_phy_hw_reset - reset the phy, hardware style + * @hw: Struct containing variables accessed by shared code + * + * Returns the PHY to the power-on reset state + */ s32 e1000_phy_hw_reset(struct e1000_hw *hw) { - u32 ctrl, ctrl_ext; - u32 led_ctrl; - s32 ret_val; - u16 swfw; - - DEBUGFUNC("e1000_phy_hw_reset"); - - /* In the case of the phy reset being blocked, it's not an error, we - * simply return success without performing the reset. */ - ret_val = e1000_check_phy_reset_block(hw); - if (ret_val) - return E1000_SUCCESS; - - DEBUGOUT("Resetting Phy...\n"); - - if (hw->mac_type > e1000_82543) { - if ((hw->mac_type == e1000_80003es2lan) && - (er32(STATUS) & E1000_STATUS_FUNC_1)) { - swfw = E1000_SWFW_PHY1_SM; - } else { - swfw = E1000_SWFW_PHY0_SM; - } - if (e1000_swfw_sync_acquire(hw, swfw)) { - DEBUGOUT("Unable to acquire swfw sync\n"); - return -E1000_ERR_SWFW_SYNC; - } - /* Read the device control register and assert the E1000_CTRL_PHY_RST - * bit. Then, take it out of reset. - * For pre-e1000_82571 hardware, we delay for 10ms between the assert - * and deassert. For e1000_82571 hardware and later, we instead delay - * for 50us between and 10ms after the deassertion. - */ - ctrl = er32(CTRL); - ew32(CTRL, ctrl | E1000_CTRL_PHY_RST); - E1000_WRITE_FLUSH(); - - if (hw->mac_type < e1000_82571) - msleep(10); - else - udelay(100); - - ew32(CTRL, ctrl); - E1000_WRITE_FLUSH(); - - if (hw->mac_type >= e1000_82571) - mdelay(10); - - e1000_swfw_sync_release(hw, swfw); - } else { - /* Read the Extended Device Control Register, assert the PHY_RESET_DIR - * bit to put the PHY into reset. Then, take it out of reset. - */ - ctrl_ext = er32(CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; - ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; - ew32(CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(); - msleep(10); - ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; - ew32(CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(); - } - udelay(150); - - if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { - /* Configure activity LED after PHY reset */ - led_ctrl = er32(LEDCTL); - led_ctrl &= IGP_ACTIVITY_LED_MASK; - led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); - ew32(LEDCTL, led_ctrl); - } - - /* Wait for FW to finish PHY configuration. */ - ret_val = e1000_get_phy_cfg_done(hw); - if (ret_val != E1000_SUCCESS) - return ret_val; - e1000_release_software_semaphore(hw); - - if ((hw->mac_type == e1000_ich8lan) && (hw->phy_type == e1000_phy_igp_3)) - ret_val = e1000_init_lcd_from_nvm(hw); - - return ret_val; + u32 ctrl, ctrl_ext; + u32 led_ctrl; + s32 ret_val; + + DEBUGFUNC("e1000_phy_hw_reset"); + + DEBUGOUT("Resetting Phy...\n"); + + if (hw->mac_type > e1000_82543) { + /* Read the device control register and assert the E1000_CTRL_PHY_RST + * bit. Then, take it out of reset. + * For e1000 hardware, we delay for 10ms between the assert + * and deassert. + */ + ctrl = er32(CTRL); + ew32(CTRL, ctrl | E1000_CTRL_PHY_RST); + E1000_WRITE_FLUSH(); + + msleep(10); + + ew32(CTRL, ctrl); + E1000_WRITE_FLUSH(); + + } else { + /* Read the Extended Device Control Register, assert the PHY_RESET_DIR + * bit to put the PHY into reset. Then, take it out of reset. + */ + ctrl_ext = er32(CTRL_EXT); + ctrl_ext |= E1000_CTRL_EXT_SDP4_DIR; + ctrl_ext &= ~E1000_CTRL_EXT_SDP4_DATA; + ew32(CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(); + msleep(10); + ctrl_ext |= E1000_CTRL_EXT_SDP4_DATA; + ew32(CTRL_EXT, ctrl_ext); + E1000_WRITE_FLUSH(); + } + udelay(150); + + if ((hw->mac_type == e1000_82541) || (hw->mac_type == e1000_82547)) { + /* Configure activity LED after PHY reset */ + led_ctrl = er32(LEDCTL); + led_ctrl &= IGP_ACTIVITY_LED_MASK; + led_ctrl |= (IGP_ACTIVITY_LED_ENABLE | IGP_LED3_MODE); + ew32(LEDCTL, led_ctrl); + } + + /* Wait for FW to finish PHY configuration. */ + ret_val = e1000_get_phy_cfg_done(hw); + if (ret_val != E1000_SUCCESS) + return ret_val; + + return ret_val; } -/****************************************************************************** -* Resets the PHY -* -* hw - Struct containing variables accessed by shared code -* -* Sets bit 15 of the MII Control register -******************************************************************************/ +/** + * e1000_phy_reset - reset the phy to commit settings + * @hw: Struct containing variables accessed by shared code + * + * Resets the PHY + * Sets bit 15 of the MII Control register + */ s32 e1000_phy_reset(struct e1000_hw *hw) { - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_phy_reset"); - - /* In the case of the phy reset being blocked, it's not an error, we - * simply return success without performing the reset. */ - ret_val = e1000_check_phy_reset_block(hw); - if (ret_val) - return E1000_SUCCESS; - - switch (hw->phy_type) { - case e1000_phy_igp: - case e1000_phy_igp_2: - case e1000_phy_igp_3: - case e1000_phy_ife: - ret_val = e1000_phy_hw_reset(hw); - if (ret_val) - return ret_val; - break; - default: - ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_data |= MII_CR_RESET; - ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); - if (ret_val) - return ret_val; - - udelay(1); - break; - } - - if (hw->phy_type == e1000_phy_igp || hw->phy_type == e1000_phy_igp_2) - e1000_phy_init_script(hw); - - return E1000_SUCCESS; -} + s32 ret_val; + u16 phy_data; -/****************************************************************************** -* Work-around for 82566 power-down: on D3 entry- -* 1) disable gigabit link -* 2) write VR power-down enable -* 3) read it back -* if successful continue, else issue LCD reset and repeat -* -* hw - struct containing variables accessed by shared code -******************************************************************************/ -void e1000_phy_powerdown_workaround(struct e1000_hw *hw) -{ - s32 reg; - u16 phy_data; - s32 retry = 0; + DEBUGFUNC("e1000_phy_reset"); - DEBUGFUNC("e1000_phy_powerdown_workaround"); + switch (hw->phy_type) { + case e1000_phy_igp: + ret_val = e1000_phy_hw_reset(hw); + if (ret_val) + return ret_val; + break; + default: + ret_val = e1000_read_phy_reg(hw, PHY_CTRL, &phy_data); + if (ret_val) + return ret_val; - if (hw->phy_type != e1000_phy_igp_3) - return; + phy_data |= MII_CR_RESET; + ret_val = e1000_write_phy_reg(hw, PHY_CTRL, phy_data); + if (ret_val) + return ret_val; - do { - /* Disable link */ - reg = er32(PHY_CTRL); - ew32(PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | - E1000_PHY_CTRL_NOND0A_GBE_DISABLE); + udelay(1); + break; + } - /* Write VR power-down enable - bits 9:8 should be 10b */ - e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); - phy_data |= (1 << 9); - phy_data &= ~(1 << 8); - e1000_write_phy_reg(hw, IGP3_VR_CTRL, phy_data); + if (hw->phy_type == e1000_phy_igp) + e1000_phy_init_script(hw); - /* Read it back and test */ - e1000_read_phy_reg(hw, IGP3_VR_CTRL, &phy_data); - if (((phy_data & IGP3_VR_CTRL_MODE_MASK) == IGP3_VR_CTRL_MODE_SHUT) || retry) - break; + return E1000_SUCCESS; +} - /* Issue PHY reset and repeat at most one more time */ - reg = er32(CTRL); - ew32(CTRL, reg | E1000_CTRL_PHY_RST); - retry++; - } while (retry); +/** + * e1000_detect_gig_phy - check the phy type + * @hw: Struct containing variables accessed by shared code + * + * Probes the expected PHY address for known PHY IDs + */ +static s32 e1000_detect_gig_phy(struct e1000_hw *hw) +{ + s32 phy_init_status, ret_val; + u16 phy_id_high, phy_id_low; + bool match = false; - return; + DEBUGFUNC("e1000_detect_gig_phy"); -} + if (hw->phy_id != 0) + return E1000_SUCCESS; -/****************************************************************************** -* Work-around for 82566 Kumeran PCS lock loss: -* On link status change (i.e. PCI reset, speed change) and link is up and -* speed is gigabit- -* 0) if workaround is optionally disabled do nothing -* 1) wait 1ms for Kumeran link to come up -* 2) check Kumeran Diagnostic register PCS lock loss bit -* 3) if not set the link is locked (all is good), otherwise... -* 4) reset the PHY -* 5) repeat up to 10 times -* Note: this is only called for IGP3 copper when speed is 1gb. -* -* hw - struct containing variables accessed by shared code -******************************************************************************/ -static s32 e1000_kumeran_lock_loss_workaround(struct e1000_hw *hw) -{ - s32 ret_val; - s32 reg; - s32 cnt; - u16 phy_data; - - if (hw->kmrn_lock_loss_workaround_disabled) - return E1000_SUCCESS; - - /* Make sure link is up before proceeding. If not just return. - * Attempting this while link is negotiating fouled up link - * stability */ - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - - if (phy_data & MII_SR_LINK_STATUS) { - for (cnt = 0; cnt < 10; cnt++) { - /* read once to clear */ - ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); - if (ret_val) - return ret_val; - /* and again to get new status */ - ret_val = e1000_read_phy_reg(hw, IGP3_KMRN_DIAG, &phy_data); - if (ret_val) - return ret_val; - - /* check for PCS lock */ - if (!(phy_data & IGP3_KMRN_DIAG_PCS_LOCK_LOSS)) - return E1000_SUCCESS; - - /* Issue PHY reset */ - e1000_phy_hw_reset(hw); - mdelay(5); - } - /* Disable GigE link negotiation */ - reg = er32(PHY_CTRL); - ew32(PHY_CTRL, reg | E1000_PHY_CTRL_GBE_DISABLE | - E1000_PHY_CTRL_NOND0A_GBE_DISABLE); - - /* unable to acquire PCS lock */ - return E1000_ERR_PHY; - } - - return E1000_SUCCESS; -} + /* Read the PHY ID Registers to identify which PHY is onboard. */ + ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); + if (ret_val) + return ret_val; -/****************************************************************************** -* Probes the expected PHY address for known PHY IDs -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ -static s32 e1000_detect_gig_phy(struct e1000_hw *hw) -{ - s32 phy_init_status, ret_val; - u16 phy_id_high, phy_id_low; - bool match = false; - - DEBUGFUNC("e1000_detect_gig_phy"); - - if (hw->phy_id != 0) - return E1000_SUCCESS; - - /* The 82571 firmware may still be configuring the PHY. In this - * case, we cannot access the PHY until the configuration is done. So - * we explicitly set the PHY values. */ - if (hw->mac_type == e1000_82571 || - hw->mac_type == e1000_82572) { - hw->phy_id = IGP01E1000_I_PHY_ID; - hw->phy_type = e1000_phy_igp_2; - return E1000_SUCCESS; - } - - /* ESB-2 PHY reads require e1000_phy_gg82563 to be set because of a work- - * around that forces PHY page 0 to be set or the reads fail. The rest of - * the code in this routine uses e1000_read_phy_reg to read the PHY ID. - * So for ESB-2 we need to have this set so our reads won't fail. If the - * attached PHY is not a e1000_phy_gg82563, the routines below will figure - * this out as well. */ - if (hw->mac_type == e1000_80003es2lan) - hw->phy_type = e1000_phy_gg82563; - - /* Read the PHY ID Registers to identify which PHY is onboard. */ - ret_val = e1000_read_phy_reg(hw, PHY_ID1, &phy_id_high); - if (ret_val) - return ret_val; - - hw->phy_id = (u32)(phy_id_high << 16); - udelay(20); - ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low); - if (ret_val) - return ret_val; - - hw->phy_id |= (u32)(phy_id_low & PHY_REVISION_MASK); - hw->phy_revision = (u32)phy_id_low & ~PHY_REVISION_MASK; - - switch (hw->mac_type) { - case e1000_82543: - if (hw->phy_id == M88E1000_E_PHY_ID) match = true; - break; - case e1000_82544: - if (hw->phy_id == M88E1000_I_PHY_ID) match = true; - break; - case e1000_82540: - case e1000_82545: - case e1000_82545_rev_3: - case e1000_82546: - case e1000_82546_rev_3: - if (hw->phy_id == M88E1011_I_PHY_ID) match = true; - break; - case e1000_82541: - case e1000_82541_rev_2: - case e1000_82547: - case e1000_82547_rev_2: - if (hw->phy_id == IGP01E1000_I_PHY_ID) match = true; - break; - case e1000_82573: - if (hw->phy_id == M88E1111_I_PHY_ID) match = true; - break; - case e1000_80003es2lan: - if (hw->phy_id == GG82563_E_PHY_ID) match = true; - break; - case e1000_ich8lan: - if (hw->phy_id == IGP03E1000_E_PHY_ID) match = true; - if (hw->phy_id == IFE_E_PHY_ID) match = true; - if (hw->phy_id == IFE_PLUS_E_PHY_ID) match = true; - if (hw->phy_id == IFE_C_E_PHY_ID) match = true; - break; - default: - DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type); - return -E1000_ERR_CONFIG; - } - phy_init_status = e1000_set_phy_type(hw); - - if ((match) && (phy_init_status == E1000_SUCCESS)) { - DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id); - return E1000_SUCCESS; - } - DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id); - return -E1000_ERR_PHY; + hw->phy_id = (u32) (phy_id_high << 16); + udelay(20); + ret_val = e1000_read_phy_reg(hw, PHY_ID2, &phy_id_low); + if (ret_val) + return ret_val; + + hw->phy_id |= (u32) (phy_id_low & PHY_REVISION_MASK); + hw->phy_revision = (u32) phy_id_low & ~PHY_REVISION_MASK; + + switch (hw->mac_type) { + case e1000_82543: + if (hw->phy_id == M88E1000_E_PHY_ID) + match = true; + break; + case e1000_82544: + if (hw->phy_id == M88E1000_I_PHY_ID) + match = true; + break; + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + if (hw->phy_id == M88E1011_I_PHY_ID) + match = true; + break; + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + if (hw->phy_id == IGP01E1000_I_PHY_ID) + match = true; + break; + default: + DEBUGOUT1("Invalid MAC type %d\n", hw->mac_type); + return -E1000_ERR_CONFIG; + } + phy_init_status = e1000_set_phy_type(hw); + + if ((match) && (phy_init_status == E1000_SUCCESS)) { + DEBUGOUT1("PHY ID 0x%X detected\n", hw->phy_id); + return E1000_SUCCESS; + } + DEBUGOUT1("Invalid PHY ID 0x%X\n", hw->phy_id); + return -E1000_ERR_PHY; } -/****************************************************************************** -* Resets the PHY's DSP -* -* hw - Struct containing variables accessed by shared code -******************************************************************************/ +/** + * e1000_phy_reset_dsp - reset DSP + * @hw: Struct containing variables accessed by shared code + * + * Resets the PHY's DSP + */ static s32 e1000_phy_reset_dsp(struct e1000_hw *hw) { - s32 ret_val; - DEBUGFUNC("e1000_phy_reset_dsp"); - - do { - if (hw->phy_type != e1000_phy_gg82563) { - ret_val = e1000_write_phy_reg(hw, 29, 0x001d); - if (ret_val) break; - } - ret_val = e1000_write_phy_reg(hw, 30, 0x00c1); - if (ret_val) break; - ret_val = e1000_write_phy_reg(hw, 30, 0x0000); - if (ret_val) break; - ret_val = E1000_SUCCESS; - } while (0); - - return ret_val; + s32 ret_val; + DEBUGFUNC("e1000_phy_reset_dsp"); + + do { + ret_val = e1000_write_phy_reg(hw, 29, 0x001d); + if (ret_val) + break; + ret_val = e1000_write_phy_reg(hw, 30, 0x00c1); + if (ret_val) + break; + ret_val = e1000_write_phy_reg(hw, 30, 0x0000); + if (ret_val) + break; + ret_val = E1000_SUCCESS; + } while (0); + + return ret_val; } -/****************************************************************************** -* Get PHY information from various PHY registers for igp PHY only. -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ +/** + * e1000_phy_igp_get_info - get igp specific registers + * @hw: Struct containing variables accessed by shared code + * @phy_info: PHY information structure + * + * Get PHY information from various PHY registers for igp PHY only. + */ static s32 e1000_phy_igp_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info) { - s32 ret_val; - u16 phy_data, min_length, max_length, average; - e1000_rev_polarity polarity; - - DEBUGFUNC("e1000_phy_igp_get_info"); - - /* The downshift status is checked only once, after link is established, - * and it stored in the hw->speed_downgraded parameter. */ - phy_info->downshift = (e1000_downshift)hw->speed_downgraded; - - /* IGP01E1000 does not need to support it. */ - phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal; - - /* IGP01E1000 always correct polarity reversal */ - phy_info->polarity_correction = e1000_polarity_reversal_enabled; - - /* Check polarity status */ - ret_val = e1000_check_polarity(hw, &polarity); - if (ret_val) - return ret_val; - - phy_info->cable_polarity = polarity; - - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->mdix_mode = (e1000_auto_x_mode)((phy_data & IGP01E1000_PSSR_MDIX) >> - IGP01E1000_PSSR_MDIX_SHIFT); - - if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == - IGP01E1000_PSSR_SPEED_1000MBPS) { - /* Local/Remote Receiver Information are only valid at 1000 Mbps */ - ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> - SR_1000T_LOCAL_RX_STATUS_SHIFT) ? - e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; - phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> - SR_1000T_REMOTE_RX_STATUS_SHIFT) ? - e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; - - /* Get cable length */ - ret_val = e1000_get_cable_length(hw, &min_length, &max_length); - if (ret_val) - return ret_val; - - /* Translate to old method */ - average = (max_length + min_length) / 2; - - if (average <= e1000_igp_cable_length_50) - phy_info->cable_length = e1000_cable_length_50; - else if (average <= e1000_igp_cable_length_80) - phy_info->cable_length = e1000_cable_length_50_80; - else if (average <= e1000_igp_cable_length_110) - phy_info->cable_length = e1000_cable_length_80_110; - else if (average <= e1000_igp_cable_length_140) - phy_info->cable_length = e1000_cable_length_110_140; - else - phy_info->cable_length = e1000_cable_length_140; - } - - return E1000_SUCCESS; -} + s32 ret_val; + u16 phy_data, min_length, max_length, average; + e1000_rev_polarity polarity; + + DEBUGFUNC("e1000_phy_igp_get_info"); + + /* The downshift status is checked only once, after link is established, + * and it stored in the hw->speed_downgraded parameter. */ + phy_info->downshift = (e1000_downshift) hw->speed_downgraded; + + /* IGP01E1000 does not need to support it. */ + phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal; + + /* IGP01E1000 always correct polarity reversal */ + phy_info->polarity_correction = e1000_polarity_reversal_enabled; + + /* Check polarity status */ + ret_val = e1000_check_polarity(hw, &polarity); + if (ret_val) + return ret_val; + + phy_info->cable_polarity = polarity; + + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->mdix_mode = + (e1000_auto_x_mode) ((phy_data & IGP01E1000_PSSR_MDIX) >> + IGP01E1000_PSSR_MDIX_SHIFT); + + if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + /* Local/Remote Receiver Information are only valid at 1000 Mbps */ + ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> + SR_1000T_LOCAL_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> + SR_1000T_REMOTE_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + + /* Get cable length */ + ret_val = e1000_get_cable_length(hw, &min_length, &max_length); + if (ret_val) + return ret_val; + + /* Translate to old method */ + average = (max_length + min_length) / 2; + + if (average <= e1000_igp_cable_length_50) + phy_info->cable_length = e1000_cable_length_50; + else if (average <= e1000_igp_cable_length_80) + phy_info->cable_length = e1000_cable_length_50_80; + else if (average <= e1000_igp_cable_length_110) + phy_info->cable_length = e1000_cable_length_80_110; + else if (average <= e1000_igp_cable_length_140) + phy_info->cable_length = e1000_cable_length_110_140; + else + phy_info->cable_length = e1000_cable_length_140; + } -/****************************************************************************** -* Get PHY information from various PHY registers for ife PHY only. -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ -static s32 e1000_phy_ife_get_info(struct e1000_hw *hw, - struct e1000_phy_info *phy_info) -{ - s32 ret_val; - u16 phy_data; - e1000_rev_polarity polarity; - - DEBUGFUNC("e1000_phy_ife_get_info"); - - phy_info->downshift = (e1000_downshift)hw->speed_downgraded; - phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_normal; - - ret_val = e1000_read_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL, &phy_data); - if (ret_val) - return ret_val; - phy_info->polarity_correction = - ((phy_data & IFE_PSC_AUTO_POLARITY_DISABLE) >> - IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT) ? - e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled; - - if (phy_info->polarity_correction == e1000_polarity_reversal_enabled) { - ret_val = e1000_check_polarity(hw, &polarity); - if (ret_val) - return ret_val; - } else { - /* Polarity is forced. */ - polarity = ((phy_data & IFE_PSC_FORCE_POLARITY) >> - IFE_PSC_FORCE_POLARITY_SHIFT) ? - e1000_rev_polarity_reversed : e1000_rev_polarity_normal; - } - phy_info->cable_polarity = polarity; - - ret_val = e1000_read_phy_reg(hw, IFE_PHY_MDIX_CONTROL, &phy_data); - if (ret_val) - return ret_val; - - phy_info->mdix_mode = (e1000_auto_x_mode) - ((phy_data & (IFE_PMC_AUTO_MDIX | IFE_PMC_FORCE_MDIX)) >> - IFE_PMC_MDIX_MODE_SHIFT); - - return E1000_SUCCESS; + return E1000_SUCCESS; } -/****************************************************************************** -* Get PHY information from various PHY registers fot m88 PHY only. -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ +/** + * e1000_phy_m88_get_info - get m88 specific registers + * @hw: Struct containing variables accessed by shared code + * @phy_info: PHY information structure + * + * Get PHY information from various PHY registers for m88 PHY only. + */ static s32 e1000_phy_m88_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info) { - s32 ret_val; - u16 phy_data; - e1000_rev_polarity polarity; - - DEBUGFUNC("e1000_phy_m88_get_info"); - - /* The downshift status is checked only once, after link is established, - * and it stored in the hw->speed_downgraded parameter. */ - phy_info->downshift = (e1000_downshift)hw->speed_downgraded; - - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); - if (ret_val) - return ret_val; - - phy_info->extended_10bt_distance = - ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >> - M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ? - e1000_10bt_ext_dist_enable_lower : e1000_10bt_ext_dist_enable_normal; - - phy_info->polarity_correction = - ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >> - M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ? - e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled; - - /* Check polarity status */ - ret_val = e1000_check_polarity(hw, &polarity); - if (ret_val) - return ret_val; - phy_info->cable_polarity = polarity; - - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->mdix_mode = (e1000_auto_x_mode)((phy_data & M88E1000_PSSR_MDIX) >> - M88E1000_PSSR_MDIX_SHIFT); - - if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) { - /* Cable Length Estimation and Local/Remote Receiver Information - * are only valid at 1000 Mbps. - */ - if (hw->phy_type != e1000_phy_gg82563) { - phy_info->cable_length = (e1000_cable_length)((phy_data & M88E1000_PSSR_CABLE_LENGTH) >> - M88E1000_PSSR_CABLE_LENGTH_SHIFT); - } else { - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, - &phy_data); - if (ret_val) - return ret_val; - - phy_info->cable_length = (e1000_cable_length)(phy_data & GG82563_DSPD_CABLE_LENGTH); - } - - ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); - if (ret_val) - return ret_val; - - phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> - SR_1000T_LOCAL_RX_STATUS_SHIFT) ? - e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; - phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> - SR_1000T_REMOTE_RX_STATUS_SHIFT) ? - e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; - - } - - return E1000_SUCCESS; + s32 ret_val; + u16 phy_data; + e1000_rev_polarity polarity; + + DEBUGFUNC("e1000_phy_m88_get_info"); + + /* The downshift status is checked only once, after link is established, + * and it stored in the hw->speed_downgraded parameter. */ + phy_info->downshift = (e1000_downshift) hw->speed_downgraded; + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data); + if (ret_val) + return ret_val; + + phy_info->extended_10bt_distance = + ((phy_data & M88E1000_PSCR_10BT_EXT_DIST_ENABLE) >> + M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT) ? + e1000_10bt_ext_dist_enable_lower : + e1000_10bt_ext_dist_enable_normal; + + phy_info->polarity_correction = + ((phy_data & M88E1000_PSCR_POLARITY_REVERSAL) >> + M88E1000_PSCR_POLARITY_REVERSAL_SHIFT) ? + e1000_polarity_reversal_disabled : e1000_polarity_reversal_enabled; + + /* Check polarity status */ + ret_val = e1000_check_polarity(hw, &polarity); + if (ret_val) + return ret_val; + phy_info->cable_polarity = polarity; + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->mdix_mode = + (e1000_auto_x_mode) ((phy_data & M88E1000_PSSR_MDIX) >> + M88E1000_PSSR_MDIX_SHIFT); + + if ((phy_data & M88E1000_PSSR_SPEED) == M88E1000_PSSR_1000MBS) { + /* Cable Length Estimation and Local/Remote Receiver Information + * are only valid at 1000 Mbps. + */ + phy_info->cable_length = + (e1000_cable_length) ((phy_data & + M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT); + + ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data); + if (ret_val) + return ret_val; + + phy_info->local_rx = ((phy_data & SR_1000T_LOCAL_RX_STATUS) >> + SR_1000T_LOCAL_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + phy_info->remote_rx = ((phy_data & SR_1000T_REMOTE_RX_STATUS) >> + SR_1000T_REMOTE_RX_STATUS_SHIFT) ? + e1000_1000t_rx_status_ok : e1000_1000t_rx_status_not_ok; + + } + + return E1000_SUCCESS; } -/****************************************************************************** -* Get PHY information from various PHY registers -* -* hw - Struct containing variables accessed by shared code -* phy_info - PHY information structure -******************************************************************************/ +/** + * e1000_phy_get_info - request phy info + * @hw: Struct containing variables accessed by shared code + * @phy_info: PHY information structure + * + * Get PHY information from various PHY registers + */ s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info) { - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_phy_get_info"); - - phy_info->cable_length = e1000_cable_length_undefined; - phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined; - phy_info->cable_polarity = e1000_rev_polarity_undefined; - phy_info->downshift = e1000_downshift_undefined; - phy_info->polarity_correction = e1000_polarity_reversal_undefined; - phy_info->mdix_mode = e1000_auto_x_mode_undefined; - phy_info->local_rx = e1000_1000t_rx_status_undefined; - phy_info->remote_rx = e1000_1000t_rx_status_undefined; - - if (hw->media_type != e1000_media_type_copper) { - DEBUGOUT("PHY info is only valid for copper media\n"); - return -E1000_ERR_CONFIG; - } - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); - if (ret_val) - return ret_val; - - if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) { - DEBUGOUT("PHY info is only valid if link is up\n"); - return -E1000_ERR_CONFIG; - } - - if (hw->phy_type == e1000_phy_igp || - hw->phy_type == e1000_phy_igp_3 || - hw->phy_type == e1000_phy_igp_2) - return e1000_phy_igp_get_info(hw, phy_info); - else if (hw->phy_type == e1000_phy_ife) - return e1000_phy_ife_get_info(hw, phy_info); - else - return e1000_phy_m88_get_info(hw, phy_info); + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_phy_get_info"); + + phy_info->cable_length = e1000_cable_length_undefined; + phy_info->extended_10bt_distance = e1000_10bt_ext_dist_enable_undefined; + phy_info->cable_polarity = e1000_rev_polarity_undefined; + phy_info->downshift = e1000_downshift_undefined; + phy_info->polarity_correction = e1000_polarity_reversal_undefined; + phy_info->mdix_mode = e1000_auto_x_mode_undefined; + phy_info->local_rx = e1000_1000t_rx_status_undefined; + phy_info->remote_rx = e1000_1000t_rx_status_undefined; + + if (hw->media_type != e1000_media_type_copper) { + DEBUGOUT("PHY info is only valid for copper media\n"); + return -E1000_ERR_CONFIG; + } + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &phy_data); + if (ret_val) + return ret_val; + + if ((phy_data & MII_SR_LINK_STATUS) != MII_SR_LINK_STATUS) { + DEBUGOUT("PHY info is only valid if link is up\n"); + return -E1000_ERR_CONFIG; + } + + if (hw->phy_type == e1000_phy_igp) + return e1000_phy_igp_get_info(hw, phy_info); + else + return e1000_phy_m88_get_info(hw, phy_info); } s32 e1000_validate_mdi_setting(struct e1000_hw *hw) { - DEBUGFUNC("e1000_validate_mdi_settings"); - - if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) { - DEBUGOUT("Invalid MDI setting detected\n"); - hw->mdix = 1; - return -E1000_ERR_CONFIG; - } - return E1000_SUCCESS; -} + DEBUGFUNC("e1000_validate_mdi_settings"); + if (!hw->autoneg && (hw->mdix == 0 || hw->mdix == 3)) { + DEBUGOUT("Invalid MDI setting detected\n"); + hw->mdix = 1; + return -E1000_ERR_CONFIG; + } + return E1000_SUCCESS; +} -/****************************************************************************** - * Sets up eeprom variables in the hw struct. Must be called after mac_type - * is configured. Additionally, if this is ICH8, the flash controller GbE - * registers must be mapped, or this will crash. +/** + * e1000_init_eeprom_params - initialize sw eeprom vars + * @hw: Struct containing variables accessed by shared code * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ + * Sets up eeprom variables in the hw struct. Must be called after mac_type + * is configured. + */ s32 e1000_init_eeprom_params(struct e1000_hw *hw) { - struct e1000_eeprom_info *eeprom = &hw->eeprom; - u32 eecd = er32(EECD); - s32 ret_val = E1000_SUCCESS; - u16 eeprom_size; - - DEBUGFUNC("e1000_init_eeprom_params"); - - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - case e1000_82543: - case e1000_82544: - eeprom->type = e1000_eeprom_microwire; - eeprom->word_size = 64; - eeprom->opcode_bits = 3; - eeprom->address_bits = 6; - eeprom->delay_usec = 50; - eeprom->use_eerd = false; - eeprom->use_eewr = false; - break; - case e1000_82540: - case e1000_82545: - case e1000_82545_rev_3: - case e1000_82546: - case e1000_82546_rev_3: - eeprom->type = e1000_eeprom_microwire; - eeprom->opcode_bits = 3; - eeprom->delay_usec = 50; - if (eecd & E1000_EECD_SIZE) { - eeprom->word_size = 256; - eeprom->address_bits = 8; - } else { - eeprom->word_size = 64; - eeprom->address_bits = 6; - } - eeprom->use_eerd = false; - eeprom->use_eewr = false; - break; - case e1000_82541: - case e1000_82541_rev_2: - case e1000_82547: - case e1000_82547_rev_2: - if (eecd & E1000_EECD_TYPE) { - eeprom->type = e1000_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - } else { - eeprom->type = e1000_eeprom_microwire; - eeprom->opcode_bits = 3; - eeprom->delay_usec = 50; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->word_size = 256; - eeprom->address_bits = 8; - } else { - eeprom->word_size = 64; - eeprom->address_bits = 6; - } - } - eeprom->use_eerd = false; - eeprom->use_eewr = false; - break; - case e1000_82571: - case e1000_82572: - eeprom->type = e1000_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - eeprom->use_eerd = false; - eeprom->use_eewr = false; - break; - case e1000_82573: - eeprom->type = e1000_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - eeprom->use_eerd = true; - eeprom->use_eewr = true; - if (!e1000_is_onboard_nvm_eeprom(hw)) { - eeprom->type = e1000_eeprom_flash; - eeprom->word_size = 2048; - - /* Ensure that the Autonomous FLASH update bit is cleared due to - * Flash update issue on parts which use a FLASH for NVM. */ - eecd &= ~E1000_EECD_AUPDEN; - ew32(EECD, eecd); - } - break; - case e1000_80003es2lan: - eeprom->type = e1000_eeprom_spi; - eeprom->opcode_bits = 8; - eeprom->delay_usec = 1; - if (eecd & E1000_EECD_ADDR_BITS) { - eeprom->page_size = 32; - eeprom->address_bits = 16; - } else { - eeprom->page_size = 8; - eeprom->address_bits = 8; - } - eeprom->use_eerd = true; - eeprom->use_eewr = false; - break; - case e1000_ich8lan: - { - s32 i = 0; - u32 flash_size = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_GFPREG); - - eeprom->type = e1000_eeprom_ich8; - eeprom->use_eerd = false; - eeprom->use_eewr = false; - eeprom->word_size = E1000_SHADOW_RAM_WORDS; - - /* Zero the shadow RAM structure. But don't load it from NVM - * so as to save time for driver init */ - if (hw->eeprom_shadow_ram != NULL) { - for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { - hw->eeprom_shadow_ram[i].modified = false; - hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; - } - } - - hw->flash_base_addr = (flash_size & ICH_GFPREG_BASE_MASK) * - ICH_FLASH_SECTOR_SIZE; - - hw->flash_bank_size = ((flash_size >> 16) & ICH_GFPREG_BASE_MASK) + 1; - hw->flash_bank_size -= (flash_size & ICH_GFPREG_BASE_MASK); - - hw->flash_bank_size *= ICH_FLASH_SECTOR_SIZE; - - hw->flash_bank_size /= 2 * sizeof(u16); - - break; - } - default: - break; - } - - if (eeprom->type == e1000_eeprom_spi) { - /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to - * 32KB (incremented by powers of 2). - */ - if (hw->mac_type <= e1000_82547_rev_2) { - /* Set to default value for initial eeprom read. */ - eeprom->word_size = 64; - ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size); - if (ret_val) - return ret_val; - eeprom_size = (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT; - /* 256B eeprom size was not supported in earlier hardware, so we - * bump eeprom_size up one to ensure that "1" (which maps to 256B) - * is never the result used in the shifting logic below. */ - if (eeprom_size) - eeprom_size++; - } else { - eeprom_size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >> - E1000_EECD_SIZE_EX_SHIFT); - } - - eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT); - } - return ret_val; + struct e1000_eeprom_info *eeprom = &hw->eeprom; + u32 eecd = er32(EECD); + s32 ret_val = E1000_SUCCESS; + u16 eeprom_size; + + DEBUGFUNC("e1000_init_eeprom_params"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + eeprom->type = e1000_eeprom_microwire; + eeprom->word_size = 64; + eeprom->opcode_bits = 3; + eeprom->address_bits = 6; + eeprom->delay_usec = 50; + break; + case e1000_82540: + case e1000_82545: + case e1000_82545_rev_3: + case e1000_82546: + case e1000_82546_rev_3: + eeprom->type = e1000_eeprom_microwire; + eeprom->opcode_bits = 3; + eeprom->delay_usec = 50; + if (eecd & E1000_EECD_SIZE) { + eeprom->word_size = 256; + eeprom->address_bits = 8; + } else { + eeprom->word_size = 64; + eeprom->address_bits = 6; + } + break; + case e1000_82541: + case e1000_82541_rev_2: + case e1000_82547: + case e1000_82547_rev_2: + if (eecd & E1000_EECD_TYPE) { + eeprom->type = e1000_eeprom_spi; + eeprom->opcode_bits = 8; + eeprom->delay_usec = 1; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->page_size = 32; + eeprom->address_bits = 16; + } else { + eeprom->page_size = 8; + eeprom->address_bits = 8; + } + } else { + eeprom->type = e1000_eeprom_microwire; + eeprom->opcode_bits = 3; + eeprom->delay_usec = 50; + if (eecd & E1000_EECD_ADDR_BITS) { + eeprom->word_size = 256; + eeprom->address_bits = 8; + } else { + eeprom->word_size = 64; + eeprom->address_bits = 6; + } + } + break; + default: + break; + } + + if (eeprom->type == e1000_eeprom_spi) { + /* eeprom_size will be an enum [0..8] that maps to eeprom sizes 128B to + * 32KB (incremented by powers of 2). + */ + /* Set to default value for initial eeprom read. */ + eeprom->word_size = 64; + ret_val = e1000_read_eeprom(hw, EEPROM_CFG, 1, &eeprom_size); + if (ret_val) + return ret_val; + eeprom_size = + (eeprom_size & EEPROM_SIZE_MASK) >> EEPROM_SIZE_SHIFT; + /* 256B eeprom size was not supported in earlier hardware, so we + * bump eeprom_size up one to ensure that "1" (which maps to 256B) + * is never the result used in the shifting logic below. */ + if (eeprom_size) + eeprom_size++; + + eeprom->word_size = 1 << (eeprom_size + EEPROM_WORD_SIZE_SHIFT); + } + return ret_val; } -/****************************************************************************** - * Raises the EEPROM's clock input. - * - * hw - Struct containing variables accessed by shared code - * eecd - EECD's current value - *****************************************************************************/ +/** + * e1000_raise_ee_clk - Raises the EEPROM's clock input. + * @hw: Struct containing variables accessed by shared code + * @eecd: EECD's current value + */ static void e1000_raise_ee_clk(struct e1000_hw *hw, u32 *eecd) { - /* Raise the clock input to the EEPROM (by setting the SK bit), and then - * wait <delay> microseconds. - */ - *eecd = *eecd | E1000_EECD_SK; - ew32(EECD, *eecd); - E1000_WRITE_FLUSH(); - udelay(hw->eeprom.delay_usec); + /* Raise the clock input to the EEPROM (by setting the SK bit), and then + * wait <delay> microseconds. + */ + *eecd = *eecd | E1000_EECD_SK; + ew32(EECD, *eecd); + E1000_WRITE_FLUSH(); + udelay(hw->eeprom.delay_usec); } -/****************************************************************************** - * Lowers the EEPROM's clock input. - * - * hw - Struct containing variables accessed by shared code - * eecd - EECD's current value - *****************************************************************************/ +/** + * e1000_lower_ee_clk - Lowers the EEPROM's clock input. + * @hw: Struct containing variables accessed by shared code + * @eecd: EECD's current value + */ static void e1000_lower_ee_clk(struct e1000_hw *hw, u32 *eecd) { - /* Lower the clock input to the EEPROM (by clearing the SK bit), and then - * wait 50 microseconds. - */ - *eecd = *eecd & ~E1000_EECD_SK; - ew32(EECD, *eecd); - E1000_WRITE_FLUSH(); - udelay(hw->eeprom.delay_usec); + /* Lower the clock input to the EEPROM (by clearing the SK bit), and then + * wait 50 microseconds. + */ + *eecd = *eecd & ~E1000_EECD_SK; + ew32(EECD, *eecd); + E1000_WRITE_FLUSH(); + udelay(hw->eeprom.delay_usec); } -/****************************************************************************** - * Shift data bits out to the EEPROM. - * - * hw - Struct containing variables accessed by shared code - * data - data to send to the EEPROM - * count - number of bits to shift out - *****************************************************************************/ +/** + * e1000_shift_out_ee_bits - Shift data bits out to the EEPROM. + * @hw: Struct containing variables accessed by shared code + * @data: data to send to the EEPROM + * @count: number of bits to shift out + */ static void e1000_shift_out_ee_bits(struct e1000_hw *hw, u16 data, u16 count) { - struct e1000_eeprom_info *eeprom = &hw->eeprom; - u32 eecd; - u32 mask; - - /* We need to shift "count" bits out to the EEPROM. So, value in the - * "data" parameter will be shifted out to the EEPROM one bit at a time. - * In order to do this, "data" must be broken down into bits. - */ - mask = 0x01 << (count - 1); - eecd = er32(EECD); - if (eeprom->type == e1000_eeprom_microwire) { - eecd &= ~E1000_EECD_DO; - } else if (eeprom->type == e1000_eeprom_spi) { - eecd |= E1000_EECD_DO; - } - do { - /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", - * and then raising and then lowering the clock (the SK bit controls - * the clock input to the EEPROM). A "0" is shifted out to the EEPROM - * by setting "DI" to "0" and then raising and then lowering the clock. - */ - eecd &= ~E1000_EECD_DI; - - if (data & mask) - eecd |= E1000_EECD_DI; - - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - - udelay(eeprom->delay_usec); - - e1000_raise_ee_clk(hw, &eecd); - e1000_lower_ee_clk(hw, &eecd); - - mask = mask >> 1; - - } while (mask); - - /* We leave the "DI" bit set to "0" when we leave this routine. */ - eecd &= ~E1000_EECD_DI; - ew32(EECD, eecd); + struct e1000_eeprom_info *eeprom = &hw->eeprom; + u32 eecd; + u32 mask; + + /* We need to shift "count" bits out to the EEPROM. So, value in the + * "data" parameter will be shifted out to the EEPROM one bit at a time. + * In order to do this, "data" must be broken down into bits. + */ + mask = 0x01 << (count - 1); + eecd = er32(EECD); + if (eeprom->type == e1000_eeprom_microwire) { + eecd &= ~E1000_EECD_DO; + } else if (eeprom->type == e1000_eeprom_spi) { + eecd |= E1000_EECD_DO; + } + do { + /* A "1" is shifted out to the EEPROM by setting bit "DI" to a "1", + * and then raising and then lowering the clock (the SK bit controls + * the clock input to the EEPROM). A "0" is shifted out to the EEPROM + * by setting "DI" to "0" and then raising and then lowering the clock. + */ + eecd &= ~E1000_EECD_DI; + + if (data & mask) + eecd |= E1000_EECD_DI; + + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + + udelay(eeprom->delay_usec); + + e1000_raise_ee_clk(hw, &eecd); + e1000_lower_ee_clk(hw, &eecd); + + mask = mask >> 1; + + } while (mask); + + /* We leave the "DI" bit set to "0" when we leave this routine. */ + eecd &= ~E1000_EECD_DI; + ew32(EECD, eecd); } -/****************************************************************************** - * Shift data bits in from the EEPROM - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_shift_in_ee_bits - Shift data bits in from the EEPROM + * @hw: Struct containing variables accessed by shared code + * @count: number of bits to shift in + */ static u16 e1000_shift_in_ee_bits(struct e1000_hw *hw, u16 count) { - u32 eecd; - u32 i; - u16 data; + u32 eecd; + u32 i; + u16 data; - /* In order to read a register from the EEPROM, we need to shift 'count' - * bits in from the EEPROM. Bits are "shifted in" by raising the clock - * input to the EEPROM (setting the SK bit), and then reading the value of - * the "DO" bit. During this "shifting in" process the "DI" bit should - * always be clear. - */ + /* In order to read a register from the EEPROM, we need to shift 'count' + * bits in from the EEPROM. Bits are "shifted in" by raising the clock + * input to the EEPROM (setting the SK bit), and then reading the value of + * the "DO" bit. During this "shifting in" process the "DI" bit should + * always be clear. + */ - eecd = er32(EECD); + eecd = er32(EECD); - eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); - data = 0; + eecd &= ~(E1000_EECD_DO | E1000_EECD_DI); + data = 0; - for (i = 0; i < count; i++) { - data = data << 1; - e1000_raise_ee_clk(hw, &eecd); + for (i = 0; i < count; i++) { + data = data << 1; + e1000_raise_ee_clk(hw, &eecd); - eecd = er32(EECD); + eecd = er32(EECD); - eecd &= ~(E1000_EECD_DI); - if (eecd & E1000_EECD_DO) - data |= 1; + eecd &= ~(E1000_EECD_DI); + if (eecd & E1000_EECD_DO) + data |= 1; - e1000_lower_ee_clk(hw, &eecd); - } + e1000_lower_ee_clk(hw, &eecd); + } - return data; + return data; } -/****************************************************************************** - * Prepares EEPROM for access - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_acquire_eeprom - Prepares EEPROM for access + * @hw: Struct containing variables accessed by shared code * * Lowers EEPROM clock. Clears input pin. Sets the chip select pin. This * function should be called before issuing a command to the EEPROM. - *****************************************************************************/ + */ static s32 e1000_acquire_eeprom(struct e1000_hw *hw) { - struct e1000_eeprom_info *eeprom = &hw->eeprom; - u32 eecd, i=0; - - DEBUGFUNC("e1000_acquire_eeprom"); - - if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) - return -E1000_ERR_SWFW_SYNC; - eecd = er32(EECD); - - if (hw->mac_type != e1000_82573) { - /* Request EEPROM Access */ - if (hw->mac_type > e1000_82544) { - eecd |= E1000_EECD_REQ; - ew32(EECD, eecd); - eecd = er32(EECD); - while ((!(eecd & E1000_EECD_GNT)) && - (i < E1000_EEPROM_GRANT_ATTEMPTS)) { - i++; - udelay(5); - eecd = er32(EECD); - } - if (!(eecd & E1000_EECD_GNT)) { - eecd &= ~E1000_EECD_REQ; - ew32(EECD, eecd); - DEBUGOUT("Could not acquire EEPROM grant\n"); - e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); - return -E1000_ERR_EEPROM; - } - } - } - - /* Setup EEPROM for Read/Write */ - - if (eeprom->type == e1000_eeprom_microwire) { - /* Clear SK and DI */ - eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); - ew32(EECD, eecd); - - /* Set CS */ - eecd |= E1000_EECD_CS; - ew32(EECD, eecd); - } else if (eeprom->type == e1000_eeprom_spi) { - /* Clear SK and CS */ - eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); - ew32(EECD, eecd); - udelay(1); - } - - return E1000_SUCCESS; + struct e1000_eeprom_info *eeprom = &hw->eeprom; + u32 eecd, i = 0; + + DEBUGFUNC("e1000_acquire_eeprom"); + + eecd = er32(EECD); + + /* Request EEPROM Access */ + if (hw->mac_type > e1000_82544) { + eecd |= E1000_EECD_REQ; + ew32(EECD, eecd); + eecd = er32(EECD); + while ((!(eecd & E1000_EECD_GNT)) && + (i < E1000_EEPROM_GRANT_ATTEMPTS)) { + i++; + udelay(5); + eecd = er32(EECD); + } + if (!(eecd & E1000_EECD_GNT)) { + eecd &= ~E1000_EECD_REQ; + ew32(EECD, eecd); + DEBUGOUT("Could not acquire EEPROM grant\n"); + return -E1000_ERR_EEPROM; + } + } + + /* Setup EEPROM for Read/Write */ + + if (eeprom->type == e1000_eeprom_microwire) { + /* Clear SK and DI */ + eecd &= ~(E1000_EECD_DI | E1000_EECD_SK); + ew32(EECD, eecd); + + /* Set CS */ + eecd |= E1000_EECD_CS; + ew32(EECD, eecd); + } else if (eeprom->type == e1000_eeprom_spi) { + /* Clear SK and CS */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + ew32(EECD, eecd); + udelay(1); + } + + return E1000_SUCCESS; } -/****************************************************************************** - * Returns EEPROM to a "standby" state - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_standby_eeprom - Returns EEPROM to a "standby" state + * @hw: Struct containing variables accessed by shared code + */ static void e1000_standby_eeprom(struct e1000_hw *hw) { - struct e1000_eeprom_info *eeprom = &hw->eeprom; - u32 eecd; - - eecd = er32(EECD); - - if (eeprom->type == e1000_eeprom_microwire) { - eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(eeprom->delay_usec); - - /* Clock high */ - eecd |= E1000_EECD_SK; - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(eeprom->delay_usec); - - /* Select EEPROM */ - eecd |= E1000_EECD_CS; - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(eeprom->delay_usec); - - /* Clock low */ - eecd &= ~E1000_EECD_SK; - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(eeprom->delay_usec); - } else if (eeprom->type == e1000_eeprom_spi) { - /* Toggle CS to flush commands */ - eecd |= E1000_EECD_CS; - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(eeprom->delay_usec); - eecd &= ~E1000_EECD_CS; - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(eeprom->delay_usec); - } + struct e1000_eeprom_info *eeprom = &hw->eeprom; + u32 eecd; + + eecd = er32(EECD); + + if (eeprom->type == e1000_eeprom_microwire) { + eecd &= ~(E1000_EECD_CS | E1000_EECD_SK); + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(eeprom->delay_usec); + + /* Clock high */ + eecd |= E1000_EECD_SK; + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(eeprom->delay_usec); + + /* Select EEPROM */ + eecd |= E1000_EECD_CS; + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(eeprom->delay_usec); + + /* Clock low */ + eecd &= ~E1000_EECD_SK; + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(eeprom->delay_usec); + } else if (eeprom->type == e1000_eeprom_spi) { + /* Toggle CS to flush commands */ + eecd |= E1000_EECD_CS; + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(eeprom->delay_usec); + eecd &= ~E1000_EECD_CS; + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(eeprom->delay_usec); + } } -/****************************************************************************** - * Terminates a command by inverting the EEPROM's chip select pin +/** + * e1000_release_eeprom - drop chip select + * @hw: Struct containing variables accessed by shared code * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ + * Terminates a command by inverting the EEPROM's chip select pin + */ static void e1000_release_eeprom(struct e1000_hw *hw) { - u32 eecd; - - DEBUGFUNC("e1000_release_eeprom"); + u32 eecd; - eecd = er32(EECD); + DEBUGFUNC("e1000_release_eeprom"); - if (hw->eeprom.type == e1000_eeprom_spi) { - eecd |= E1000_EECD_CS; /* Pull CS high */ - eecd &= ~E1000_EECD_SK; /* Lower SCK */ + eecd = er32(EECD); - ew32(EECD, eecd); + if (hw->eeprom.type == e1000_eeprom_spi) { + eecd |= E1000_EECD_CS; /* Pull CS high */ + eecd &= ~E1000_EECD_SK; /* Lower SCK */ - udelay(hw->eeprom.delay_usec); - } else if (hw->eeprom.type == e1000_eeprom_microwire) { - /* cleanup eeprom */ + ew32(EECD, eecd); - /* CS on Microwire is active-high */ - eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); + udelay(hw->eeprom.delay_usec); + } else if (hw->eeprom.type == e1000_eeprom_microwire) { + /* cleanup eeprom */ - ew32(EECD, eecd); + /* CS on Microwire is active-high */ + eecd &= ~(E1000_EECD_CS | E1000_EECD_DI); - /* Rising edge of clock */ - eecd |= E1000_EECD_SK; - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(hw->eeprom.delay_usec); + ew32(EECD, eecd); - /* Falling edge of clock */ - eecd &= ~E1000_EECD_SK; - ew32(EECD, eecd); - E1000_WRITE_FLUSH(); - udelay(hw->eeprom.delay_usec); - } + /* Rising edge of clock */ + eecd |= E1000_EECD_SK; + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(hw->eeprom.delay_usec); - /* Stop requesting EEPROM access */ - if (hw->mac_type > e1000_82544) { - eecd &= ~E1000_EECD_REQ; - ew32(EECD, eecd); - } + /* Falling edge of clock */ + eecd &= ~E1000_EECD_SK; + ew32(EECD, eecd); + E1000_WRITE_FLUSH(); + udelay(hw->eeprom.delay_usec); + } - e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); + /* Stop requesting EEPROM access */ + if (hw->mac_type > e1000_82544) { + eecd &= ~E1000_EECD_REQ; + ew32(EECD, eecd); + } } -/****************************************************************************** - * Reads a 16 bit word from the EEPROM. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_spi_eeprom_ready - Reads a 16 bit word from the EEPROM. + * @hw: Struct containing variables accessed by shared code + */ static s32 e1000_spi_eeprom_ready(struct e1000_hw *hw) { - u16 retry_count = 0; - u8 spi_stat_reg; - - DEBUGFUNC("e1000_spi_eeprom_ready"); - - /* Read "Status Register" repeatedly until the LSB is cleared. The - * EEPROM will signal that the command has been completed by clearing - * bit 0 of the internal status register. If it's not cleared within - * 5 milliseconds, then error out. - */ - retry_count = 0; - do { - e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI, - hw->eeprom.opcode_bits); - spi_stat_reg = (u8)e1000_shift_in_ee_bits(hw, 8); - if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI)) - break; - - udelay(5); - retry_count += 5; - - e1000_standby_eeprom(hw); - } while (retry_count < EEPROM_MAX_RETRY_SPI); - - /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and - * only 0-5mSec on 5V devices) - */ - if (retry_count >= EEPROM_MAX_RETRY_SPI) { - DEBUGOUT("SPI EEPROM Status error\n"); - return -E1000_ERR_EEPROM; - } - - return E1000_SUCCESS; -} - -/****************************************************************************** - * Reads a 16 bit word from the EEPROM. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -s32 e1000_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) -{ - s32 ret; - spin_lock(&e1000_eeprom_lock); - ret = e1000_do_read_eeprom(hw, offset, words, data); - spin_unlock(&e1000_eeprom_lock); - return ret; -} - -static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) -{ - struct e1000_eeprom_info *eeprom = &hw->eeprom; - u32 i = 0; - - DEBUGFUNC("e1000_read_eeprom"); - - /* If eeprom is not yet detected, do so now */ - if (eeprom->word_size == 0) - e1000_init_eeprom_params(hw); - - /* A check for invalid values: offset too large, too many words, and not - * enough words. - */ - if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || - (words == 0)) { - DEBUGOUT2("\"words\" parameter out of bounds. Words = %d, size = %d\n", offset, eeprom->word_size); - return -E1000_ERR_EEPROM; - } - - /* EEPROM's that don't use EERD to read require us to bit-bang the SPI - * directly. In this case, we need to acquire the EEPROM so that - * FW or other port software does not interrupt. - */ - if (e1000_is_onboard_nvm_eeprom(hw) && !hw->eeprom.use_eerd) { - /* Prepare the EEPROM for bit-bang reading */ - if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) - return -E1000_ERR_EEPROM; - } - - /* Eerd register EEPROM access requires no eeprom aquire/release */ - if (eeprom->use_eerd) - return e1000_read_eeprom_eerd(hw, offset, words, data); - - /* ICH EEPROM access is done via the ICH flash controller */ - if (eeprom->type == e1000_eeprom_ich8) - return e1000_read_eeprom_ich8(hw, offset, words, data); - - /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have - * acquired the EEPROM at this point, so any returns should relase it */ - if (eeprom->type == e1000_eeprom_spi) { - u16 word_in; - u8 read_opcode = EEPROM_READ_OPCODE_SPI; - - if (e1000_spi_eeprom_ready(hw)) { - e1000_release_eeprom(hw); - return -E1000_ERR_EEPROM; - } - - e1000_standby_eeprom(hw); - - /* Some SPI eeproms use the 8th address bit embedded in the opcode */ - if ((eeprom->address_bits == 8) && (offset >= 128)) - read_opcode |= EEPROM_A8_OPCODE_SPI; - - /* Send the READ command (opcode + addr) */ - e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits); - e1000_shift_out_ee_bits(hw, (u16)(offset*2), eeprom->address_bits); - - /* Read the data. The address of the eeprom internally increments with - * each byte (spi) being read, saving on the overhead of eeprom setup - * and tear-down. The address counter will roll over if reading beyond - * the size of the eeprom, thus allowing the entire memory to be read - * starting from any offset. */ - for (i = 0; i < words; i++) { - word_in = e1000_shift_in_ee_bits(hw, 16); - data[i] = (word_in >> 8) | (word_in << 8); - } - } else if (eeprom->type == e1000_eeprom_microwire) { - for (i = 0; i < words; i++) { - /* Send the READ command (opcode + addr) */ - e1000_shift_out_ee_bits(hw, EEPROM_READ_OPCODE_MICROWIRE, - eeprom->opcode_bits); - e1000_shift_out_ee_bits(hw, (u16)(offset + i), - eeprom->address_bits); - - /* Read the data. For microwire, each word requires the overhead - * of eeprom setup and tear-down. */ - data[i] = e1000_shift_in_ee_bits(hw, 16); - e1000_standby_eeprom(hw); - } - } - - /* End this read operation */ - e1000_release_eeprom(hw); - - return E1000_SUCCESS; -} + u16 retry_count = 0; + u8 spi_stat_reg; -/****************************************************************************** - * Reads a 16 bit word from the EEPROM using the EERD register. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -static s32 e1000_read_eeprom_eerd(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data) -{ - u32 i, eerd = 0; - s32 error = 0; + DEBUGFUNC("e1000_spi_eeprom_ready"); - for (i = 0; i < words; i++) { - eerd = ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) + - E1000_EEPROM_RW_REG_START; + /* Read "Status Register" repeatedly until the LSB is cleared. The + * EEPROM will signal that the command has been completed by clearing + * bit 0 of the internal status register. If it's not cleared within + * 5 milliseconds, then error out. + */ + retry_count = 0; + do { + e1000_shift_out_ee_bits(hw, EEPROM_RDSR_OPCODE_SPI, + hw->eeprom.opcode_bits); + spi_stat_reg = (u8) e1000_shift_in_ee_bits(hw, 8); + if (!(spi_stat_reg & EEPROM_STATUS_RDY_SPI)) + break; - ew32(EERD, eerd); - error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ); + udelay(5); + retry_count += 5; - if (error) { - break; - } - data[i] = (er32(EERD) >> E1000_EEPROM_RW_REG_DATA); + e1000_standby_eeprom(hw); + } while (retry_count < EEPROM_MAX_RETRY_SPI); - } + /* ATMEL SPI write time could vary from 0-20mSec on 3.3V devices (and + * only 0-5mSec on 5V devices) + */ + if (retry_count >= EEPROM_MAX_RETRY_SPI) { + DEBUGOUT("SPI EEPROM Status error\n"); + return -E1000_ERR_EEPROM; + } - return error; + return E1000_SUCCESS; } -/****************************************************************************** - * Writes a 16 bit word from the EEPROM using the EEWR register. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -static s32 e1000_write_eeprom_eewr(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data) +/** + * e1000_read_eeprom - Reads a 16 bit word from the EEPROM. + * @hw: Struct containing variables accessed by shared code + * @offset: offset of word in the EEPROM to read + * @data: word read from the EEPROM + * @words: number of words to read + */ +s32 e1000_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) { - u32 register_value = 0; - u32 i = 0; - s32 error = 0; - - if (e1000_swfw_sync_acquire(hw, E1000_SWFW_EEP_SM)) - return -E1000_ERR_SWFW_SYNC; - - for (i = 0; i < words; i++) { - register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | - ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) | - E1000_EEPROM_RW_REG_START; - - error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); - if (error) { - break; - } - - ew32(EEWR, register_value); - - error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE); - - if (error) { - break; - } - } - - e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM); - return error; + s32 ret; + spin_lock(&e1000_eeprom_lock); + ret = e1000_do_read_eeprom(hw, offset, words, data); + spin_unlock(&e1000_eeprom_lock); + return ret; } -/****************************************************************************** - * Polls the status bit (bit 1) of the EERD to determine when the read is done. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static s32 e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd) +static s32 e1000_do_read_eeprom(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) { - u32 attempts = 100000; - u32 i, reg = 0; - s32 done = E1000_ERR_EEPROM; - - for (i = 0; i < attempts; i++) { - if (eerd == E1000_EEPROM_POLL_READ) - reg = er32(EERD); - else - reg = er32(EEWR); - - if (reg & E1000_EEPROM_RW_REG_DONE) { - done = E1000_SUCCESS; - break; - } - udelay(5); - } - - return done; -} + struct e1000_eeprom_info *eeprom = &hw->eeprom; + u32 i = 0; -/*************************************************************************** -* Description: Determines if the onboard NVM is FLASH or EEPROM. -* -* hw - Struct containing variables accessed by shared code -****************************************************************************/ -static bool e1000_is_onboard_nvm_eeprom(struct e1000_hw *hw) -{ - u32 eecd = 0; + DEBUGFUNC("e1000_read_eeprom"); - DEBUGFUNC("e1000_is_onboard_nvm_eeprom"); + /* If eeprom is not yet detected, do so now */ + if (eeprom->word_size == 0) + e1000_init_eeprom_params(hw); + + /* A check for invalid values: offset too large, too many words, and not + * enough words. + */ + if ((offset >= eeprom->word_size) + || (words > eeprom->word_size - offset) || (words == 0)) { + DEBUGOUT2 + ("\"words\" parameter out of bounds. Words = %d, size = %d\n", + offset, eeprom->word_size); + return -E1000_ERR_EEPROM; + } - if (hw->mac_type == e1000_ich8lan) - return false; + /* EEPROM's that don't use EERD to read require us to bit-bang the SPI + * directly. In this case, we need to acquire the EEPROM so that + * FW or other port software does not interrupt. + */ + /* Prepare the EEPROM for bit-bang reading */ + if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) + return -E1000_ERR_EEPROM; + + /* Set up the SPI or Microwire EEPROM for bit-bang reading. We have + * acquired the EEPROM at this point, so any returns should release it */ + if (eeprom->type == e1000_eeprom_spi) { + u16 word_in; + u8 read_opcode = EEPROM_READ_OPCODE_SPI; + + if (e1000_spi_eeprom_ready(hw)) { + e1000_release_eeprom(hw); + return -E1000_ERR_EEPROM; + } - if (hw->mac_type == e1000_82573) { - eecd = er32(EECD); + e1000_standby_eeprom(hw); + + /* Some SPI eeproms use the 8th address bit embedded in the opcode */ + if ((eeprom->address_bits == 8) && (offset >= 128)) + read_opcode |= EEPROM_A8_OPCODE_SPI; + + /* Send the READ command (opcode + addr) */ + e1000_shift_out_ee_bits(hw, read_opcode, eeprom->opcode_bits); + e1000_shift_out_ee_bits(hw, (u16) (offset * 2), + eeprom->address_bits); + + /* Read the data. The address of the eeprom internally increments with + * each byte (spi) being read, saving on the overhead of eeprom setup + * and tear-down. The address counter will roll over if reading beyond + * the size of the eeprom, thus allowing the entire memory to be read + * starting from any offset. */ + for (i = 0; i < words; i++) { + word_in = e1000_shift_in_ee_bits(hw, 16); + data[i] = (word_in >> 8) | (word_in << 8); + } + } else if (eeprom->type == e1000_eeprom_microwire) { + for (i = 0; i < words; i++) { + /* Send the READ command (opcode + addr) */ + e1000_shift_out_ee_bits(hw, + EEPROM_READ_OPCODE_MICROWIRE, + eeprom->opcode_bits); + e1000_shift_out_ee_bits(hw, (u16) (offset + i), + eeprom->address_bits); + + /* Read the data. For microwire, each word requires the overhead + * of eeprom setup and tear-down. */ + data[i] = e1000_shift_in_ee_bits(hw, 16); + e1000_standby_eeprom(hw); + } + } - /* Isolate bits 15 & 16 */ - eecd = ((eecd >> 15) & 0x03); + /* End this read operation */ + e1000_release_eeprom(hw); - /* If both bits are set, device is Flash type */ - if (eecd == 0x03) { - return false; - } - } - return true; + return E1000_SUCCESS; } -/****************************************************************************** - * Verifies that the EEPROM has a valid checksum - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_validate_eeprom_checksum - Verifies that the EEPROM has a valid checksum + * @hw: Struct containing variables accessed by shared code * * Reads the first 64 16 bit words of the EEPROM and sums the values read. * If the the sum of the 64 16 bit words is 0xBABA, the EEPROM's checksum is * valid. - *****************************************************************************/ + */ s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw) { - u16 checksum = 0; - u16 i, eeprom_data; - - DEBUGFUNC("e1000_validate_eeprom_checksum"); - - if ((hw->mac_type == e1000_82573) && !e1000_is_onboard_nvm_eeprom(hw)) { - /* Check bit 4 of word 10h. If it is 0, firmware is done updating - * 10h-12h. Checksum may need to be fixed. */ - e1000_read_eeprom(hw, 0x10, 1, &eeprom_data); - if ((eeprom_data & 0x10) == 0) { - /* Read 0x23 and check bit 15. This bit is a 1 when the checksum - * has already been fixed. If the checksum is still wrong and this - * bit is a 1, we need to return bad checksum. Otherwise, we need - * to set this bit to a 1 and update the checksum. */ - e1000_read_eeprom(hw, 0x23, 1, &eeprom_data); - if ((eeprom_data & 0x8000) == 0) { - eeprom_data |= 0x8000; - e1000_write_eeprom(hw, 0x23, 1, &eeprom_data); - e1000_update_eeprom_checksum(hw); - } - } - } - - if (hw->mac_type == e1000_ich8lan) { - /* Drivers must allocate the shadow ram structure for the - * EEPROM checksum to be updated. Otherwise, this bit as well - * as the checksum must both be set correctly for this - * validation to pass. - */ - e1000_read_eeprom(hw, 0x19, 1, &eeprom_data); - if ((eeprom_data & 0x40) == 0) { - eeprom_data |= 0x40; - e1000_write_eeprom(hw, 0x19, 1, &eeprom_data); - e1000_update_eeprom_checksum(hw); - } - } - - for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { - if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - checksum += eeprom_data; - } - - if (checksum == (u16)EEPROM_SUM) - return E1000_SUCCESS; - else { - DEBUGOUT("EEPROM Checksum Invalid\n"); - return -E1000_ERR_EEPROM; - } + u16 checksum = 0; + u16 i, eeprom_data; + + DEBUGFUNC("e1000_validate_eeprom_checksum"); + + for (i = 0; i < (EEPROM_CHECKSUM_REG + 1); i++) { + if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + checksum += eeprom_data; + } + + if (checksum == (u16) EEPROM_SUM) + return E1000_SUCCESS; + else { + DEBUGOUT("EEPROM Checksum Invalid\n"); + return -E1000_ERR_EEPROM; + } } -/****************************************************************************** - * Calculates the EEPROM checksum and writes it to the EEPROM - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_update_eeprom_checksum - Calculates/writes the EEPROM checksum + * @hw: Struct containing variables accessed by shared code * * Sums the first 63 16 bit words of the EEPROM. Subtracts the sum from 0xBABA. * Writes the difference to word offset 63 of the EEPROM. - *****************************************************************************/ + */ s32 e1000_update_eeprom_checksum(struct e1000_hw *hw) { - u32 ctrl_ext; - u16 checksum = 0; - u16 i, eeprom_data; - - DEBUGFUNC("e1000_update_eeprom_checksum"); - - for (i = 0; i < EEPROM_CHECKSUM_REG; i++) { - if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - checksum += eeprom_data; - } - checksum = (u16)EEPROM_SUM - checksum; - if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) { - DEBUGOUT("EEPROM Write Error\n"); - return -E1000_ERR_EEPROM; - } else if (hw->eeprom.type == e1000_eeprom_flash) { - e1000_commit_shadow_ram(hw); - } else if (hw->eeprom.type == e1000_eeprom_ich8) { - e1000_commit_shadow_ram(hw); - /* Reload the EEPROM, or else modifications will not appear - * until after next adapter reset. */ - ctrl_ext = er32(CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_EE_RST; - ew32(CTRL_EXT, ctrl_ext); - msleep(10); - } - return E1000_SUCCESS; + u16 checksum = 0; + u16 i, eeprom_data; + + DEBUGFUNC("e1000_update_eeprom_checksum"); + + for (i = 0; i < EEPROM_CHECKSUM_REG; i++) { + if (e1000_read_eeprom(hw, i, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + checksum += eeprom_data; + } + checksum = (u16) EEPROM_SUM - checksum; + if (e1000_write_eeprom(hw, EEPROM_CHECKSUM_REG, 1, &checksum) < 0) { + DEBUGOUT("EEPROM Write Error\n"); + return -E1000_ERR_EEPROM; + } + return E1000_SUCCESS; } -/****************************************************************************** - * Parent function for writing words to the different EEPROM types. - * - * hw - Struct containing variables accessed by shared code - * offset - offset within the EEPROM to be written to - * words - number of words to write - * data - 16 bit word to be written to the EEPROM +/** + * e1000_write_eeprom - write words to the different EEPROM types. + * @hw: Struct containing variables accessed by shared code + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: 16 bit word to be written to the EEPROM * * If e1000_update_eeprom_checksum is not called after this function, the * EEPROM will most likely contain an invalid checksum. - *****************************************************************************/ + */ s32 e1000_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) { - s32 ret; - spin_lock(&e1000_eeprom_lock); - ret = e1000_do_write_eeprom(hw, offset, words, data); - spin_unlock(&e1000_eeprom_lock); - return ret; + s32 ret; + spin_lock(&e1000_eeprom_lock); + ret = e1000_do_write_eeprom(hw, offset, words, data); + spin_unlock(&e1000_eeprom_lock); + return ret; } - -static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) +static s32 e1000_do_write_eeprom(struct e1000_hw *hw, u16 offset, u16 words, + u16 *data) { - struct e1000_eeprom_info *eeprom = &hw->eeprom; - s32 status = 0; - - DEBUGFUNC("e1000_write_eeprom"); - - /* If eeprom is not yet detected, do so now */ - if (eeprom->word_size == 0) - e1000_init_eeprom_params(hw); - - /* A check for invalid values: offset too large, too many words, and not - * enough words. - */ - if ((offset >= eeprom->word_size) || (words > eeprom->word_size - offset) || - (words == 0)) { - DEBUGOUT("\"words\" parameter out of bounds\n"); - return -E1000_ERR_EEPROM; - } - - /* 82573 writes only through eewr */ - if (eeprom->use_eewr) - return e1000_write_eeprom_eewr(hw, offset, words, data); - - if (eeprom->type == e1000_eeprom_ich8) - return e1000_write_eeprom_ich8(hw, offset, words, data); - - /* Prepare the EEPROM for writing */ - if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) - return -E1000_ERR_EEPROM; - - if (eeprom->type == e1000_eeprom_microwire) { - status = e1000_write_eeprom_microwire(hw, offset, words, data); - } else { - status = e1000_write_eeprom_spi(hw, offset, words, data); - msleep(10); - } - - /* Done with writing */ - e1000_release_eeprom(hw); - - return status; + struct e1000_eeprom_info *eeprom = &hw->eeprom; + s32 status = 0; + + DEBUGFUNC("e1000_write_eeprom"); + + /* If eeprom is not yet detected, do so now */ + if (eeprom->word_size == 0) + e1000_init_eeprom_params(hw); + + /* A check for invalid values: offset too large, too many words, and not + * enough words. + */ + if ((offset >= eeprom->word_size) + || (words > eeprom->word_size - offset) || (words == 0)) { + DEBUGOUT("\"words\" parameter out of bounds\n"); + return -E1000_ERR_EEPROM; + } + + /* Prepare the EEPROM for writing */ + if (e1000_acquire_eeprom(hw) != E1000_SUCCESS) + return -E1000_ERR_EEPROM; + + if (eeprom->type == e1000_eeprom_microwire) { + status = e1000_write_eeprom_microwire(hw, offset, words, data); + } else { + status = e1000_write_eeprom_spi(hw, offset, words, data); + msleep(10); + } + + /* Done with writing */ + e1000_release_eeprom(hw); + + return status; } -/****************************************************************************** - * Writes a 16 bit word to a given offset in an SPI EEPROM. - * - * hw - Struct containing variables accessed by shared code - * offset - offset within the EEPROM to be written to - * words - number of words to write - * data - pointer to array of 8 bit words to be written to the EEPROM - * - *****************************************************************************/ +/** + * e1000_write_eeprom_spi - Writes a 16 bit word to a given offset in an SPI EEPROM. + * @hw: Struct containing variables accessed by shared code + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: pointer to array of 8 bit words to be written to the EEPROM + */ static s32 e1000_write_eeprom_spi(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) { - struct e1000_eeprom_info *eeprom = &hw->eeprom; - u16 widx = 0; + struct e1000_eeprom_info *eeprom = &hw->eeprom; + u16 widx = 0; - DEBUGFUNC("e1000_write_eeprom_spi"); + DEBUGFUNC("e1000_write_eeprom_spi"); - while (widx < words) { - u8 write_opcode = EEPROM_WRITE_OPCODE_SPI; + while (widx < words) { + u8 write_opcode = EEPROM_WRITE_OPCODE_SPI; - if (e1000_spi_eeprom_ready(hw)) return -E1000_ERR_EEPROM; + if (e1000_spi_eeprom_ready(hw)) + return -E1000_ERR_EEPROM; - e1000_standby_eeprom(hw); + e1000_standby_eeprom(hw); - /* Send the WRITE ENABLE command (8 bit opcode ) */ - e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI, - eeprom->opcode_bits); + /* Send the WRITE ENABLE command (8 bit opcode ) */ + e1000_shift_out_ee_bits(hw, EEPROM_WREN_OPCODE_SPI, + eeprom->opcode_bits); - e1000_standby_eeprom(hw); + e1000_standby_eeprom(hw); - /* Some SPI eeproms use the 8th address bit embedded in the opcode */ - if ((eeprom->address_bits == 8) && (offset >= 128)) - write_opcode |= EEPROM_A8_OPCODE_SPI; + /* Some SPI eeproms use the 8th address bit embedded in the opcode */ + if ((eeprom->address_bits == 8) && (offset >= 128)) + write_opcode |= EEPROM_A8_OPCODE_SPI; - /* Send the Write command (8-bit opcode + addr) */ - e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits); + /* Send the Write command (8-bit opcode + addr) */ + e1000_shift_out_ee_bits(hw, write_opcode, eeprom->opcode_bits); - e1000_shift_out_ee_bits(hw, (u16)((offset + widx)*2), - eeprom->address_bits); + e1000_shift_out_ee_bits(hw, (u16) ((offset + widx) * 2), + eeprom->address_bits); - /* Send the data */ + /* Send the data */ - /* Loop to allow for up to whole page write (32 bytes) of eeprom */ - while (widx < words) { - u16 word_out = data[widx]; - word_out = (word_out >> 8) | (word_out << 8); - e1000_shift_out_ee_bits(hw, word_out, 16); - widx++; + /* Loop to allow for up to whole page write (32 bytes) of eeprom */ + while (widx < words) { + u16 word_out = data[widx]; + word_out = (word_out >> 8) | (word_out << 8); + e1000_shift_out_ee_bits(hw, word_out, 16); + widx++; - /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE - * operation, while the smaller eeproms are capable of an 8-byte - * PAGE WRITE operation. Break the inner loop to pass new address - */ - if ((((offset + widx)*2) % eeprom->page_size) == 0) { - e1000_standby_eeprom(hw); - break; - } - } - } + /* Some larger eeprom sizes are capable of a 32-byte PAGE WRITE + * operation, while the smaller eeproms are capable of an 8-byte + * PAGE WRITE operation. Break the inner loop to pass new address + */ + if ((((offset + widx) * 2) % eeprom->page_size) == 0) { + e1000_standby_eeprom(hw); + break; + } + } + } - return E1000_SUCCESS; + return E1000_SUCCESS; } -/****************************************************************************** - * Writes a 16 bit word to a given offset in a Microwire EEPROM. - * - * hw - Struct containing variables accessed by shared code - * offset - offset within the EEPROM to be written to - * words - number of words to write - * data - pointer to array of 16 bit words to be written to the EEPROM - * - *****************************************************************************/ +/** + * e1000_write_eeprom_microwire - Writes a 16 bit word to a given offset in a Microwire EEPROM. + * @hw: Struct containing variables accessed by shared code + * @offset: offset within the EEPROM to be written to + * @words: number of words to write + * @data: pointer to array of 8 bit words to be written to the EEPROM + */ static s32 e1000_write_eeprom_microwire(struct e1000_hw *hw, u16 offset, u16 words, u16 *data) { - struct e1000_eeprom_info *eeprom = &hw->eeprom; - u32 eecd; - u16 words_written = 0; - u16 i = 0; - - DEBUGFUNC("e1000_write_eeprom_microwire"); - - /* Send the write enable command to the EEPROM (3-bit opcode plus - * 6/8-bit dummy address beginning with 11). It's less work to include - * the 11 of the dummy address as part of the opcode than it is to shift - * it over the correct number of bits for the address. This puts the - * EEPROM into write/erase mode. - */ - e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE, - (u16)(eeprom->opcode_bits + 2)); - - e1000_shift_out_ee_bits(hw, 0, (u16)(eeprom->address_bits - 2)); - - /* Prepare the EEPROM */ - e1000_standby_eeprom(hw); - - while (words_written < words) { - /* Send the Write command (3-bit opcode + addr) */ - e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE, - eeprom->opcode_bits); - - e1000_shift_out_ee_bits(hw, (u16)(offset + words_written), - eeprom->address_bits); - - /* Send the data */ - e1000_shift_out_ee_bits(hw, data[words_written], 16); - - /* Toggle the CS line. This in effect tells the EEPROM to execute - * the previous command. - */ - e1000_standby_eeprom(hw); - - /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will - * signal that the command has been completed by raising the DO signal. - * If DO does not go high in 10 milliseconds, then error out. - */ - for (i = 0; i < 200; i++) { - eecd = er32(EECD); - if (eecd & E1000_EECD_DO) break; - udelay(50); - } - if (i == 200) { - DEBUGOUT("EEPROM Write did not complete\n"); - return -E1000_ERR_EEPROM; - } - - /* Recover from write */ - e1000_standby_eeprom(hw); - - words_written++; - } - - /* Send the write disable command to the EEPROM (3-bit opcode plus - * 6/8-bit dummy address beginning with 10). It's less work to include - * the 10 of the dummy address as part of the opcode than it is to shift - * it over the correct number of bits for the address. This takes the - * EEPROM out of write/erase mode. - */ - e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE, - (u16)(eeprom->opcode_bits + 2)); - - e1000_shift_out_ee_bits(hw, 0, (u16)(eeprom->address_bits - 2)); - - return E1000_SUCCESS; -} + struct e1000_eeprom_info *eeprom = &hw->eeprom; + u32 eecd; + u16 words_written = 0; + u16 i = 0; -/****************************************************************************** - * Flushes the cached eeprom to NVM. This is done by saving the modified values - * in the eeprom cache and the non modified values in the currently active bank - * to the new bank. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -static s32 e1000_commit_shadow_ram(struct e1000_hw *hw) -{ - u32 attempts = 100000; - u32 eecd = 0; - u32 flop = 0; - u32 i = 0; - s32 error = E1000_SUCCESS; - u32 old_bank_offset = 0; - u32 new_bank_offset = 0; - u8 low_byte = 0; - u8 high_byte = 0; - bool sector_write_failed = false; - - if (hw->mac_type == e1000_82573) { - /* The flop register will be used to determine if flash type is STM */ - flop = er32(FLOP); - for (i=0; i < attempts; i++) { - eecd = er32(EECD); - if ((eecd & E1000_EECD_FLUPD) == 0) { - break; - } - udelay(5); - } - - if (i == attempts) { - return -E1000_ERR_EEPROM; - } - - /* If STM opcode located in bits 15:8 of flop, reset firmware */ - if ((flop & 0xFF00) == E1000_STM_OPCODE) { - ew32(HICR, E1000_HICR_FW_RESET); - } - - /* Perform the flash update */ - ew32(EECD, eecd | E1000_EECD_FLUPD); - - for (i=0; i < attempts; i++) { - eecd = er32(EECD); - if ((eecd & E1000_EECD_FLUPD) == 0) { - break; - } - udelay(5); - } - - if (i == attempts) { - return -E1000_ERR_EEPROM; - } - } - - if (hw->mac_type == e1000_ich8lan && hw->eeprom_shadow_ram != NULL) { - /* We're writing to the opposite bank so if we're on bank 1, - * write to bank 0 etc. We also need to erase the segment that - * is going to be written */ - if (!(er32(EECD) & E1000_EECD_SEC1VAL)) { - new_bank_offset = hw->flash_bank_size * 2; - old_bank_offset = 0; - e1000_erase_ich8_4k_segment(hw, 1); - } else { - old_bank_offset = hw->flash_bank_size * 2; - new_bank_offset = 0; - e1000_erase_ich8_4k_segment(hw, 0); - } - - sector_write_failed = false; - /* Loop for every byte in the shadow RAM, - * which is in units of words. */ - for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { - /* Determine whether to write the value stored - * in the other NVM bank or a modified value stored - * in the shadow RAM */ - if (hw->eeprom_shadow_ram[i].modified) { - low_byte = (u8)hw->eeprom_shadow_ram[i].eeprom_word; - udelay(100); - error = e1000_verify_write_ich8_byte(hw, - (i << 1) + new_bank_offset, low_byte); - - if (error != E1000_SUCCESS) - sector_write_failed = true; - else { - high_byte = - (u8)(hw->eeprom_shadow_ram[i].eeprom_word >> 8); - udelay(100); - } - } else { - e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset, - &low_byte); - udelay(100); - error = e1000_verify_write_ich8_byte(hw, - (i << 1) + new_bank_offset, low_byte); - - if (error != E1000_SUCCESS) - sector_write_failed = true; - else { - e1000_read_ich8_byte(hw, (i << 1) + old_bank_offset + 1, - &high_byte); - udelay(100); - } - } - - /* If the write of the low byte was successful, go ahead and - * write the high byte while checking to make sure that if it - * is the signature byte, then it is handled properly */ - if (!sector_write_failed) { - /* If the word is 0x13, then make sure the signature bits - * (15:14) are 11b until the commit has completed. - * This will allow us to write 10b which indicates the - * signature is valid. We want to do this after the write - * has completed so that we don't mark the segment valid - * while the write is still in progress */ - if (i == E1000_ICH_NVM_SIG_WORD) - high_byte = E1000_ICH_NVM_SIG_MASK | high_byte; - - error = e1000_verify_write_ich8_byte(hw, - (i << 1) + new_bank_offset + 1, high_byte); - if (error != E1000_SUCCESS) - sector_write_failed = true; - - } else { - /* If the write failed then break from the loop and - * return an error */ - break; - } - } - - /* Don't bother writing the segment valid bits if sector - * programming failed. */ - if (!sector_write_failed) { - /* Finally validate the new segment by setting bit 15:14 - * to 10b in word 0x13 , this can be done without an - * erase as well since these bits are 11 to start with - * and we need to change bit 14 to 0b */ - e1000_read_ich8_byte(hw, - E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, - &high_byte); - high_byte &= 0xBF; - error = e1000_verify_write_ich8_byte(hw, - E1000_ICH_NVM_SIG_WORD * 2 + 1 + new_bank_offset, high_byte); - /* And invalidate the previously valid segment by setting - * its signature word (0x13) high_byte to 0b. This can be - * done without an erase because flash erase sets all bits - * to 1's. We can write 1's to 0's without an erase */ - if (error == E1000_SUCCESS) { - error = e1000_verify_write_ich8_byte(hw, - E1000_ICH_NVM_SIG_WORD * 2 + 1 + old_bank_offset, 0); - } - - /* Clear the now not used entry in the cache */ - for (i = 0; i < E1000_SHADOW_RAM_WORDS; i++) { - hw->eeprom_shadow_ram[i].modified = false; - hw->eeprom_shadow_ram[i].eeprom_word = 0xFFFF; - } - } - } - - return error; + DEBUGFUNC("e1000_write_eeprom_microwire"); + + /* Send the write enable command to the EEPROM (3-bit opcode plus + * 6/8-bit dummy address beginning with 11). It's less work to include + * the 11 of the dummy address as part of the opcode than it is to shift + * it over the correct number of bits for the address. This puts the + * EEPROM into write/erase mode. + */ + e1000_shift_out_ee_bits(hw, EEPROM_EWEN_OPCODE_MICROWIRE, + (u16) (eeprom->opcode_bits + 2)); + + e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2)); + + /* Prepare the EEPROM */ + e1000_standby_eeprom(hw); + + while (words_written < words) { + /* Send the Write command (3-bit opcode + addr) */ + e1000_shift_out_ee_bits(hw, EEPROM_WRITE_OPCODE_MICROWIRE, + eeprom->opcode_bits); + + e1000_shift_out_ee_bits(hw, (u16) (offset + words_written), + eeprom->address_bits); + + /* Send the data */ + e1000_shift_out_ee_bits(hw, data[words_written], 16); + + /* Toggle the CS line. This in effect tells the EEPROM to execute + * the previous command. + */ + e1000_standby_eeprom(hw); + + /* Read DO repeatedly until it is high (equal to '1'). The EEPROM will + * signal that the command has been completed by raising the DO signal. + * If DO does not go high in 10 milliseconds, then error out. + */ + for (i = 0; i < 200; i++) { + eecd = er32(EECD); + if (eecd & E1000_EECD_DO) + break; + udelay(50); + } + if (i == 200) { + DEBUGOUT("EEPROM Write did not complete\n"); + return -E1000_ERR_EEPROM; + } + + /* Recover from write */ + e1000_standby_eeprom(hw); + + words_written++; + } + + /* Send the write disable command to the EEPROM (3-bit opcode plus + * 6/8-bit dummy address beginning with 10). It's less work to include + * the 10 of the dummy address as part of the opcode than it is to shift + * it over the correct number of bits for the address. This takes the + * EEPROM out of write/erase mode. + */ + e1000_shift_out_ee_bits(hw, EEPROM_EWDS_OPCODE_MICROWIRE, + (u16) (eeprom->opcode_bits + 2)); + + e1000_shift_out_ee_bits(hw, 0, (u16) (eeprom->address_bits - 2)); + + return E1000_SUCCESS; } -/****************************************************************************** +/** + * e1000_read_mac_addr - read the adapters MAC from eeprom + * @hw: Struct containing variables accessed by shared code + * * Reads the adapter's MAC address from the EEPROM and inverts the LSB for the * second function of dual function devices - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ + */ s32 e1000_read_mac_addr(struct e1000_hw *hw) { - u16 offset; - u16 eeprom_data, i; - - DEBUGFUNC("e1000_read_mac_addr"); - - for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { - offset = i >> 1; - if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - hw->perm_mac_addr[i] = (u8)(eeprom_data & 0x00FF); - hw->perm_mac_addr[i+1] = (u8)(eeprom_data >> 8); - } - - switch (hw->mac_type) { - default: - break; - case e1000_82546: - case e1000_82546_rev_3: - case e1000_82571: - case e1000_80003es2lan: - if (er32(STATUS) & E1000_STATUS_FUNC_1) - hw->perm_mac_addr[5] ^= 0x01; - break; - } - - for (i = 0; i < NODE_ADDRESS_SIZE; i++) - hw->mac_addr[i] = hw->perm_mac_addr[i]; - return E1000_SUCCESS; + u16 offset; + u16 eeprom_data, i; + + DEBUGFUNC("e1000_read_mac_addr"); + + for (i = 0; i < NODE_ADDRESS_SIZE; i += 2) { + offset = i >> 1; + if (e1000_read_eeprom(hw, offset, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + hw->perm_mac_addr[i] = (u8) (eeprom_data & 0x00FF); + hw->perm_mac_addr[i + 1] = (u8) (eeprom_data >> 8); + } + + switch (hw->mac_type) { + default: + break; + case e1000_82546: + case e1000_82546_rev_3: + if (er32(STATUS) & E1000_STATUS_FUNC_1) + hw->perm_mac_addr[5] ^= 0x01; + break; + } + + for (i = 0; i < NODE_ADDRESS_SIZE; i++) + hw->mac_addr[i] = hw->perm_mac_addr[i]; + return E1000_SUCCESS; } -/****************************************************************************** - * Initializes receive address filters. - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_init_rx_addrs - Initializes receive address filters. + * @hw: Struct containing variables accessed by shared code * * Places the MAC address in receive address register 0 and clears the rest - * of the receive addresss registers. Clears the multicast table. Assumes + * of the receive address registers. Clears the multicast table. Assumes * the receiver is in reset when the routine is called. - *****************************************************************************/ + */ static void e1000_init_rx_addrs(struct e1000_hw *hw) { - u32 i; - u32 rar_num; - - DEBUGFUNC("e1000_init_rx_addrs"); - - /* Setup the receive address. */ - DEBUGOUT("Programming MAC Address into RAR[0]\n"); - - e1000_rar_set(hw, hw->mac_addr, 0); - - rar_num = E1000_RAR_ENTRIES; - - /* Reserve a spot for the Locally Administered Address to work around - * an 82571 issue in which a reset on one port will reload the MAC on - * the other port. */ - if ((hw->mac_type == e1000_82571) && (hw->laa_is_present)) - rar_num -= 1; - if (hw->mac_type == e1000_ich8lan) - rar_num = E1000_RAR_ENTRIES_ICH8LAN; - - /* Zero out the other 15 receive addresses. */ - DEBUGOUT("Clearing RAR[1-15]\n"); - for (i = 1; i < rar_num; i++) { - E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); - E1000_WRITE_FLUSH(); - E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); - E1000_WRITE_FLUSH(); - } + u32 i; + u32 rar_num; + + DEBUGFUNC("e1000_init_rx_addrs"); + + /* Setup the receive address. */ + DEBUGOUT("Programming MAC Address into RAR[0]\n"); + + e1000_rar_set(hw, hw->mac_addr, 0); + + rar_num = E1000_RAR_ENTRIES; + + /* Zero out the other 15 receive addresses. */ + DEBUGOUT("Clearing RAR[1-15]\n"); + for (i = 1; i < rar_num; i++) { + E1000_WRITE_REG_ARRAY(hw, RA, (i << 1), 0); + E1000_WRITE_FLUSH(); + E1000_WRITE_REG_ARRAY(hw, RA, ((i << 1) + 1), 0); + E1000_WRITE_FLUSH(); + } } -/****************************************************************************** - * Hashes an address to determine its location in the multicast table - * - * hw - Struct containing variables accessed by shared code - * mc_addr - the multicast address to hash - *****************************************************************************/ +/** + * e1000_hash_mc_addr - Hashes an address to determine its location in the multicast table + * @hw: Struct containing variables accessed by shared code + * @mc_addr: the multicast address to hash + */ u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) { - u32 hash_value = 0; - - /* The portion of the address that is used for the hash table is - * determined by the mc_filter_type setting. - */ - switch (hw->mc_filter_type) { - /* [0] [1] [2] [3] [4] [5] - * 01 AA 00 12 34 56 - * LSB MSB - */ - case 0: - if (hw->mac_type == e1000_ich8lan) { - /* [47:38] i.e. 0x158 for above example address */ - hash_value = ((mc_addr[4] >> 6) | (((u16)mc_addr[5]) << 2)); - } else { - /* [47:36] i.e. 0x563 for above example address */ - hash_value = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); - } - break; - case 1: - if (hw->mac_type == e1000_ich8lan) { - /* [46:37] i.e. 0x2B1 for above example address */ - hash_value = ((mc_addr[4] >> 5) | (((u16)mc_addr[5]) << 3)); - } else { - /* [46:35] i.e. 0xAC6 for above example address */ - hash_value = ((mc_addr[4] >> 3) | (((u16)mc_addr[5]) << 5)); - } - break; - case 2: - if (hw->mac_type == e1000_ich8lan) { - /*[45:36] i.e. 0x163 for above example address */ - hash_value = ((mc_addr[4] >> 4) | (((u16)mc_addr[5]) << 4)); - } else { - /* [45:34] i.e. 0x5D8 for above example address */ - hash_value = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); - } - break; - case 3: - if (hw->mac_type == e1000_ich8lan) { - /* [43:34] i.e. 0x18D for above example address */ - hash_value = ((mc_addr[4] >> 2) | (((u16)mc_addr[5]) << 6)); - } else { - /* [43:32] i.e. 0x634 for above example address */ - hash_value = ((mc_addr[4]) | (((u16)mc_addr[5]) << 8)); - } - break; - } - - hash_value &= 0xFFF; - if (hw->mac_type == e1000_ich8lan) - hash_value &= 0x3FF; - - return hash_value; + u32 hash_value = 0; + + /* The portion of the address that is used for the hash table is + * determined by the mc_filter_type setting. + */ + switch (hw->mc_filter_type) { + /* [0] [1] [2] [3] [4] [5] + * 01 AA 00 12 34 56 + * LSB MSB + */ + case 0: + /* [47:36] i.e. 0x563 for above example address */ + hash_value = ((mc_addr[4] >> 4) | (((u16) mc_addr[5]) << 4)); + break; + case 1: + /* [46:35] i.e. 0xAC6 for above example address */ + hash_value = ((mc_addr[4] >> 3) | (((u16) mc_addr[5]) << 5)); + break; + case 2: + /* [45:34] i.e. 0x5D8 for above example address */ + hash_value = ((mc_addr[4] >> 2) | (((u16) mc_addr[5]) << 6)); + break; + case 3: + /* [43:32] i.e. 0x634 for above example address */ + hash_value = ((mc_addr[4]) | (((u16) mc_addr[5]) << 8)); + break; + } + + hash_value &= 0xFFF; + return hash_value; } -/****************************************************************************** - * Puts an ethernet address into a receive address register. - * - * hw - Struct containing variables accessed by shared code - * addr - Address to put into receive address register - * index - Receive address register to write - *****************************************************************************/ +/** + * e1000_rar_set - Puts an ethernet address into a receive address register. + * @hw: Struct containing variables accessed by shared code + * @addr: Address to put into receive address register + * @index: Receive address register to write + */ void e1000_rar_set(struct e1000_hw *hw, u8 *addr, u32 index) { - u32 rar_low, rar_high; - - /* HW expects these in little endian so we reverse the byte order - * from network order (big endian) to little endian - */ - rar_low = ((u32)addr[0] | ((u32)addr[1] << 8) | - ((u32)addr[2] << 16) | ((u32)addr[3] << 24)); - rar_high = ((u32)addr[4] | ((u32)addr[5] << 8)); - - /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx - * unit hang. - * - * Description: - * If there are any Rx frames queued up or otherwise present in the HW - * before RSS is enabled, and then we enable RSS, the HW Rx unit will - * hang. To work around this issue, we have to disable receives and - * flush out all Rx frames before we enable RSS. To do so, we modify we - * redirect all Rx traffic to manageability and then reset the HW. - * This flushes away Rx frames, and (since the redirections to - * manageability persists across resets) keeps new ones from coming in - * while we work. Then, we clear the Address Valid AV bit for all MAC - * addresses and undo the re-direction to manageability. - * Now, frames are coming in again, but the MAC won't accept them, so - * far so good. We now proceed to initialize RSS (if necessary) and - * configure the Rx unit. Last, we re-enable the AV bits and continue - * on our merry way. - */ - switch (hw->mac_type) { - case e1000_82571: - case e1000_82572: - case e1000_80003es2lan: - if (hw->leave_av_bit_off) - break; - default: - /* Indicate to hardware the Address is Valid. */ - rar_high |= E1000_RAH_AV; - break; - } - - E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low); - E1000_WRITE_FLUSH(); - E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high); - E1000_WRITE_FLUSH(); + u32 rar_low, rar_high; + + /* HW expects these in little endian so we reverse the byte order + * from network order (big endian) to little endian + */ + rar_low = ((u32) addr[0] | ((u32) addr[1] << 8) | + ((u32) addr[2] << 16) | ((u32) addr[3] << 24)); + rar_high = ((u32) addr[4] | ((u32) addr[5] << 8)); + + /* Disable Rx and flush all Rx frames before enabling RSS to avoid Rx + * unit hang. + * + * Description: + * If there are any Rx frames queued up or otherwise present in the HW + * before RSS is enabled, and then we enable RSS, the HW Rx unit will + * hang. To work around this issue, we have to disable receives and + * flush out all Rx frames before we enable RSS. To do so, we modify we + * redirect all Rx traffic to manageability and then reset the HW. + * This flushes away Rx frames, and (since the redirections to + * manageability persists across resets) keeps new ones from coming in + * while we work. Then, we clear the Address Valid AV bit for all MAC + * addresses and undo the re-direction to manageability. + * Now, frames are coming in again, but the MAC won't accept them, so + * far so good. We now proceed to initialize RSS (if necessary) and + * configure the Rx unit. Last, we re-enable the AV bits and continue + * on our merry way. + */ + switch (hw->mac_type) { + default: + /* Indicate to hardware the Address is Valid. */ + rar_high |= E1000_RAH_AV; + break; + } + + E1000_WRITE_REG_ARRAY(hw, RA, (index << 1), rar_low); + E1000_WRITE_FLUSH(); + E1000_WRITE_REG_ARRAY(hw, RA, ((index << 1) + 1), rar_high); + E1000_WRITE_FLUSH(); } -/****************************************************************************** - * Writes a value to the specified offset in the VLAN filter table. - * - * hw - Struct containing variables accessed by shared code - * offset - Offset in VLAN filer table to write - * value - Value to write into VLAN filter table - *****************************************************************************/ +/** + * e1000_write_vfta - Writes a value to the specified offset in the VLAN filter table. + * @hw: Struct containing variables accessed by shared code + * @offset: Offset in VLAN filer table to write + * @value: Value to write into VLAN filter table + */ void e1000_write_vfta(struct e1000_hw *hw, u32 offset, u32 value) { - u32 temp; - - if (hw->mac_type == e1000_ich8lan) - return; - - if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) { - temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1)); - E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); - E1000_WRITE_FLUSH(); - E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp); - E1000_WRITE_FLUSH(); - } else { - E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); - E1000_WRITE_FLUSH(); - } + u32 temp; + + if ((hw->mac_type == e1000_82544) && ((offset & 0x1) == 1)) { + temp = E1000_READ_REG_ARRAY(hw, VFTA, (offset - 1)); + E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); + E1000_WRITE_FLUSH(); + E1000_WRITE_REG_ARRAY(hw, VFTA, (offset - 1), temp); + E1000_WRITE_FLUSH(); + } else { + E1000_WRITE_REG_ARRAY(hw, VFTA, offset, value); + E1000_WRITE_FLUSH(); + } } -/****************************************************************************** - * Clears the VLAN filer table - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_clear_vfta - Clears the VLAN filer table + * @hw: Struct containing variables accessed by shared code + */ static void e1000_clear_vfta(struct e1000_hw *hw) { - u32 offset; - u32 vfta_value = 0; - u32 vfta_offset = 0; - u32 vfta_bit_in_reg = 0; - - if (hw->mac_type == e1000_ich8lan) - return; - - if (hw->mac_type == e1000_82573) { - if (hw->mng_cookie.vlan_id != 0) { - /* The VFTA is a 4096b bit-field, each identifying a single VLAN - * ID. The following operations determine which 32b entry - * (i.e. offset) into the array we want to set the VLAN ID - * (i.e. bit) of the manageability unit. */ - vfta_offset = (hw->mng_cookie.vlan_id >> - E1000_VFTA_ENTRY_SHIFT) & - E1000_VFTA_ENTRY_MASK; - vfta_bit_in_reg = 1 << (hw->mng_cookie.vlan_id & - E1000_VFTA_ENTRY_BIT_SHIFT_MASK); - } - } - for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { - /* If the offset we want to clear is the same offset of the - * manageability VLAN ID, then clear all bits except that of the - * manageability unit */ - vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; - E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value); - E1000_WRITE_FLUSH(); - } + u32 offset; + u32 vfta_value = 0; + u32 vfta_offset = 0; + u32 vfta_bit_in_reg = 0; + + for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) { + /* If the offset we want to clear is the same offset of the + * manageability VLAN ID, then clear all bits except that of the + * manageability unit */ + vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0; + E1000_WRITE_REG_ARRAY(hw, VFTA, offset, vfta_value); + E1000_WRITE_FLUSH(); + } } static s32 e1000_id_led_init(struct e1000_hw *hw) { - u32 ledctl; - const u32 ledctl_mask = 0x000000FF; - const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON; - const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF; - u16 eeprom_data, i, temp; - const u16 led_mask = 0x0F; - - DEBUGFUNC("e1000_id_led_init"); - - if (hw->mac_type < e1000_82540) { - /* Nothing to do */ - return E1000_SUCCESS; - } - - ledctl = er32(LEDCTL); - hw->ledctl_default = ledctl; - hw->ledctl_mode1 = hw->ledctl_default; - hw->ledctl_mode2 = hw->ledctl_default; - - if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) { - DEBUGOUT("EEPROM Read Error\n"); - return -E1000_ERR_EEPROM; - } - - if ((hw->mac_type == e1000_82573) && - (eeprom_data == ID_LED_RESERVED_82573)) - eeprom_data = ID_LED_DEFAULT_82573; - else if ((eeprom_data == ID_LED_RESERVED_0000) || - (eeprom_data == ID_LED_RESERVED_FFFF)) { - if (hw->mac_type == e1000_ich8lan) - eeprom_data = ID_LED_DEFAULT_ICH8LAN; - else - eeprom_data = ID_LED_DEFAULT; - } - - for (i = 0; i < 4; i++) { - temp = (eeprom_data >> (i << 2)) & led_mask; - switch (temp) { - case ID_LED_ON1_DEF2: - case ID_LED_ON1_ON2: - case ID_LED_ON1_OFF2: - hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode1 |= ledctl_on << (i << 3); - break; - case ID_LED_OFF1_DEF2: - case ID_LED_OFF1_ON2: - case ID_LED_OFF1_OFF2: - hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode1 |= ledctl_off << (i << 3); - break; - default: - /* Do nothing */ - break; - } - switch (temp) { - case ID_LED_DEF1_ON2: - case ID_LED_ON1_ON2: - case ID_LED_OFF1_ON2: - hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode2 |= ledctl_on << (i << 3); - break; - case ID_LED_DEF1_OFF2: - case ID_LED_ON1_OFF2: - case ID_LED_OFF1_OFF2: - hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); - hw->ledctl_mode2 |= ledctl_off << (i << 3); - break; - default: - /* Do nothing */ - break; - } - } - return E1000_SUCCESS; + u32 ledctl; + const u32 ledctl_mask = 0x000000FF; + const u32 ledctl_on = E1000_LEDCTL_MODE_LED_ON; + const u32 ledctl_off = E1000_LEDCTL_MODE_LED_OFF; + u16 eeprom_data, i, temp; + const u16 led_mask = 0x0F; + + DEBUGFUNC("e1000_id_led_init"); + + if (hw->mac_type < e1000_82540) { + /* Nothing to do */ + return E1000_SUCCESS; + } + + ledctl = er32(LEDCTL); + hw->ledctl_default = ledctl; + hw->ledctl_mode1 = hw->ledctl_default; + hw->ledctl_mode2 = hw->ledctl_default; + + if (e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, 1, &eeprom_data) < 0) { + DEBUGOUT("EEPROM Read Error\n"); + return -E1000_ERR_EEPROM; + } + + if ((eeprom_data == ID_LED_RESERVED_0000) || + (eeprom_data == ID_LED_RESERVED_FFFF)) { + eeprom_data = ID_LED_DEFAULT; + } + + for (i = 0; i < 4; i++) { + temp = (eeprom_data >> (i << 2)) & led_mask; + switch (temp) { + case ID_LED_ON1_DEF2: + case ID_LED_ON1_ON2: + case ID_LED_ON1_OFF2: + hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode1 |= ledctl_on << (i << 3); + break; + case ID_LED_OFF1_DEF2: + case ID_LED_OFF1_ON2: + case ID_LED_OFF1_OFF2: + hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode1 |= ledctl_off << (i << 3); + break; + default: + /* Do nothing */ + break; + } + switch (temp) { + case ID_LED_DEF1_ON2: + case ID_LED_ON1_ON2: + case ID_LED_OFF1_ON2: + hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode2 |= ledctl_on << (i << 3); + break; + case ID_LED_DEF1_OFF2: + case ID_LED_ON1_OFF2: + case ID_LED_OFF1_OFF2: + hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3)); + hw->ledctl_mode2 |= ledctl_off << (i << 3); + break; + default: + /* Do nothing */ + break; + } + } + return E1000_SUCCESS; } -/****************************************************************************** - * Prepares SW controlable LED for use and saves the current state of the LED. +/** + * e1000_setup_led + * @hw: Struct containing variables accessed by shared code * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ + * Prepares SW controlable LED for use and saves the current state of the LED. + */ s32 e1000_setup_led(struct e1000_hw *hw) { - u32 ledctl; - s32 ret_val = E1000_SUCCESS; - - DEBUGFUNC("e1000_setup_led"); - - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - case e1000_82543: - case e1000_82544: - /* No setup necessary */ - break; - case e1000_82541: - case e1000_82547: - case e1000_82541_rev_2: - case e1000_82547_rev_2: - /* Turn off PHY Smart Power Down (if enabled) */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, - &hw->phy_spd_default); - if (ret_val) - return ret_val; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, - (u16)(hw->phy_spd_default & - ~IGP01E1000_GMII_SPD)); - if (ret_val) - return ret_val; - /* Fall Through */ - default: - if (hw->media_type == e1000_media_type_fiber) { - ledctl = er32(LEDCTL); - /* Save current LEDCTL settings */ - hw->ledctl_default = ledctl; - /* Turn off LED0 */ - ledctl &= ~(E1000_LEDCTL_LED0_IVRT | - E1000_LEDCTL_LED0_BLINK | - E1000_LEDCTL_LED0_MODE_MASK); - ledctl |= (E1000_LEDCTL_MODE_LED_OFF << - E1000_LEDCTL_LED0_MODE_SHIFT); - ew32(LEDCTL, ledctl); - } else if (hw->media_type == e1000_media_type_copper) - ew32(LEDCTL, hw->ledctl_mode1); - break; - } - - return E1000_SUCCESS; -} + u32 ledctl; + s32 ret_val = E1000_SUCCESS; + DEBUGFUNC("e1000_setup_led"); -/****************************************************************************** - * Used on 82571 and later Si that has LED blink bits. - * Callers must use their own timer and should have already called - * e1000_id_led_init() - * Call e1000_cleanup led() to stop blinking - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -s32 e1000_blink_led_start(struct e1000_hw *hw) -{ - s16 i; - u32 ledctl_blink = 0; - - DEBUGFUNC("e1000_id_led_blink_on"); - - if (hw->mac_type < e1000_82571) { - /* Nothing to do */ - return E1000_SUCCESS; - } - if (hw->media_type == e1000_media_type_fiber) { - /* always blink LED0 for PCI-E fiber */ - ledctl_blink = E1000_LEDCTL_LED0_BLINK | - (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED0_MODE_SHIFT); - } else { - /* set the blink bit for each LED that's "on" (0x0E) in ledctl_mode2 */ - ledctl_blink = hw->ledctl_mode2; - for (i=0; i < 4; i++) - if (((hw->ledctl_mode2 >> (i * 8)) & 0xFF) == - E1000_LEDCTL_MODE_LED_ON) - ledctl_blink |= (E1000_LEDCTL_LED0_BLINK << (i * 8)); - } - - ew32(LEDCTL, ledctl_blink); - - return E1000_SUCCESS; + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + /* No setup necessary */ + break; + case e1000_82541: + case e1000_82547: + case e1000_82541_rev_2: + case e1000_82547_rev_2: + /* Turn off PHY Smart Power Down (if enabled) */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, + &hw->phy_spd_default); + if (ret_val) + return ret_val; + ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, + (u16) (hw->phy_spd_default & + ~IGP01E1000_GMII_SPD)); + if (ret_val) + return ret_val; + /* Fall Through */ + default: + if (hw->media_type == e1000_media_type_fiber) { + ledctl = er32(LEDCTL); + /* Save current LEDCTL settings */ + hw->ledctl_default = ledctl; + /* Turn off LED0 */ + ledctl &= ~(E1000_LEDCTL_LED0_IVRT | + E1000_LEDCTL_LED0_BLINK | + E1000_LEDCTL_LED0_MODE_MASK); + ledctl |= (E1000_LEDCTL_MODE_LED_OFF << + E1000_LEDCTL_LED0_MODE_SHIFT); + ew32(LEDCTL, ledctl); + } else if (hw->media_type == e1000_media_type_copper) + ew32(LEDCTL, hw->ledctl_mode1); + break; + } + + return E1000_SUCCESS; } -/****************************************************************************** - * Restores the saved state of the SW controlable LED. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_cleanup_led - Restores the saved state of the SW controlable LED. + * @hw: Struct containing variables accessed by shared code + */ s32 e1000_cleanup_led(struct e1000_hw *hw) { - s32 ret_val = E1000_SUCCESS; - - DEBUGFUNC("e1000_cleanup_led"); - - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - case e1000_82543: - case e1000_82544: - /* No cleanup necessary */ - break; - case e1000_82541: - case e1000_82547: - case e1000_82541_rev_2: - case e1000_82547_rev_2: - /* Turn on PHY Smart Power Down (if previously enabled) */ - ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, - hw->phy_spd_default); - if (ret_val) - return ret_val; - /* Fall Through */ - default: - if (hw->phy_type == e1000_phy_ife) { - e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, 0); - break; - } - /* Restore LEDCTL settings */ - ew32(LEDCTL, hw->ledctl_default); - break; - } - - return E1000_SUCCESS; + s32 ret_val = E1000_SUCCESS; + + DEBUGFUNC("e1000_cleanup_led"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + case e1000_82544: + /* No cleanup necessary */ + break; + case e1000_82541: + case e1000_82547: + case e1000_82541_rev_2: + case e1000_82547_rev_2: + /* Turn on PHY Smart Power Down (if previously enabled) */ + ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, + hw->phy_spd_default); + if (ret_val) + return ret_val; + /* Fall Through */ + default: + /* Restore LEDCTL settings */ + ew32(LEDCTL, hw->ledctl_default); + break; + } + + return E1000_SUCCESS; } -/****************************************************************************** - * Turns on the software controllable LED - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_led_on - Turns on the software controllable LED + * @hw: Struct containing variables accessed by shared code + */ s32 e1000_led_on(struct e1000_hw *hw) { - u32 ctrl = er32(CTRL); - - DEBUGFUNC("e1000_led_on"); - - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - case e1000_82543: - /* Set SW Defineable Pin 0 to turn on the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - break; - case e1000_82544: - if (hw->media_type == e1000_media_type_fiber) { - /* Set SW Defineable Pin 0 to turn on the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else { - /* Clear SW Defineable Pin 0 to turn on the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } - break; - default: - if (hw->media_type == e1000_media_type_fiber) { - /* Clear SW Defineable Pin 0 to turn on the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else if (hw->phy_type == e1000_phy_ife) { - e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, - (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_ON)); - } else if (hw->media_type == e1000_media_type_copper) { - ew32(LEDCTL, hw->ledctl_mode2); - return E1000_SUCCESS; - } - break; - } - - ew32(CTRL, ctrl); - - return E1000_SUCCESS; + u32 ctrl = er32(CTRL); + + DEBUGFUNC("e1000_led_on"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + /* Set SW Defineable Pin 0 to turn on the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + break; + case e1000_82544: + if (hw->media_type == e1000_media_type_fiber) { + /* Set SW Defineable Pin 0 to turn on the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else { + /* Clear SW Defineable Pin 0 to turn on the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } + break; + default: + if (hw->media_type == e1000_media_type_fiber) { + /* Clear SW Defineable Pin 0 to turn on the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else if (hw->media_type == e1000_media_type_copper) { + ew32(LEDCTL, hw->ledctl_mode2); + return E1000_SUCCESS; + } + break; + } + + ew32(CTRL, ctrl); + + return E1000_SUCCESS; } -/****************************************************************************** - * Turns off the software controllable LED - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_led_off - Turns off the software controllable LED + * @hw: Struct containing variables accessed by shared code + */ s32 e1000_led_off(struct e1000_hw *hw) { - u32 ctrl = er32(CTRL); - - DEBUGFUNC("e1000_led_off"); - - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - case e1000_82543: - /* Clear SW Defineable Pin 0 to turn off the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - break; - case e1000_82544: - if (hw->media_type == e1000_media_type_fiber) { - /* Clear SW Defineable Pin 0 to turn off the LED */ - ctrl &= ~E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else { - /* Set SW Defineable Pin 0 to turn off the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } - break; - default: - if (hw->media_type == e1000_media_type_fiber) { - /* Set SW Defineable Pin 0 to turn off the LED */ - ctrl |= E1000_CTRL_SWDPIN0; - ctrl |= E1000_CTRL_SWDPIO0; - } else if (hw->phy_type == e1000_phy_ife) { - e1000_write_phy_reg(hw, IFE_PHY_SPECIAL_CONTROL_LED, - (IFE_PSCL_PROBE_MODE | IFE_PSCL_PROBE_LEDS_OFF)); - } else if (hw->media_type == e1000_media_type_copper) { - ew32(LEDCTL, hw->ledctl_mode1); - return E1000_SUCCESS; - } - break; - } - - ew32(CTRL, ctrl); - - return E1000_SUCCESS; + u32 ctrl = er32(CTRL); + + DEBUGFUNC("e1000_led_off"); + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + case e1000_82543: + /* Clear SW Defineable Pin 0 to turn off the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + break; + case e1000_82544: + if (hw->media_type == e1000_media_type_fiber) { + /* Clear SW Defineable Pin 0 to turn off the LED */ + ctrl &= ~E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else { + /* Set SW Defineable Pin 0 to turn off the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } + break; + default: + if (hw->media_type == e1000_media_type_fiber) { + /* Set SW Defineable Pin 0 to turn off the LED */ + ctrl |= E1000_CTRL_SWDPIN0; + ctrl |= E1000_CTRL_SWDPIO0; + } else if (hw->media_type == e1000_media_type_copper) { + ew32(LEDCTL, hw->ledctl_mode1); + return E1000_SUCCESS; + } + break; + } + + ew32(CTRL, ctrl); + + return E1000_SUCCESS; } -/****************************************************************************** - * Clears all hardware statistics counters. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ +/** + * e1000_clear_hw_cntrs - Clears all hardware statistics counters. + * @hw: Struct containing variables accessed by shared code + */ static void e1000_clear_hw_cntrs(struct e1000_hw *hw) { - volatile u32 temp; - - temp = er32(CRCERRS); - temp = er32(SYMERRS); - temp = er32(MPC); - temp = er32(SCC); - temp = er32(ECOL); - temp = er32(MCC); - temp = er32(LATECOL); - temp = er32(COLC); - temp = er32(DC); - temp = er32(SEC); - temp = er32(RLEC); - temp = er32(XONRXC); - temp = er32(XONTXC); - temp = er32(XOFFRXC); - temp = er32(XOFFTXC); - temp = er32(FCRUC); - - if (hw->mac_type != e1000_ich8lan) { - temp = er32(PRC64); - temp = er32(PRC127); - temp = er32(PRC255); - temp = er32(PRC511); - temp = er32(PRC1023); - temp = er32(PRC1522); - } - - temp = er32(GPRC); - temp = er32(BPRC); - temp = er32(MPRC); - temp = er32(GPTC); - temp = er32(GORCL); - temp = er32(GORCH); - temp = er32(GOTCL); - temp = er32(GOTCH); - temp = er32(RNBC); - temp = er32(RUC); - temp = er32(RFC); - temp = er32(ROC); - temp = er32(RJC); - temp = er32(TORL); - temp = er32(TORH); - temp = er32(TOTL); - temp = er32(TOTH); - temp = er32(TPR); - temp = er32(TPT); - - if (hw->mac_type != e1000_ich8lan) { - temp = er32(PTC64); - temp = er32(PTC127); - temp = er32(PTC255); - temp = er32(PTC511); - temp = er32(PTC1023); - temp = er32(PTC1522); - } - - temp = er32(MPTC); - temp = er32(BPTC); - - if (hw->mac_type < e1000_82543) return; - - temp = er32(ALGNERRC); - temp = er32(RXERRC); - temp = er32(TNCRS); - temp = er32(CEXTERR); - temp = er32(TSCTC); - temp = er32(TSCTFC); - - if (hw->mac_type <= e1000_82544) return; - - temp = er32(MGTPRC); - temp = er32(MGTPDC); - temp = er32(MGTPTC); - - if (hw->mac_type <= e1000_82547_rev_2) return; - - temp = er32(IAC); - temp = er32(ICRXOC); - - if (hw->mac_type == e1000_ich8lan) return; - - temp = er32(ICRXPTC); - temp = er32(ICRXATC); - temp = er32(ICTXPTC); - temp = er32(ICTXATC); - temp = er32(ICTXQEC); - temp = er32(ICTXQMTC); - temp = er32(ICRXDMTC); -} - -/****************************************************************************** - * Resets Adaptive IFS to its default state. - * - * hw - Struct containing variables accessed by shared code + volatile u32 temp; + + temp = er32(CRCERRS); + temp = er32(SYMERRS); + temp = er32(MPC); + temp = er32(SCC); + temp = er32(ECOL); + temp = er32(MCC); + temp = er32(LATECOL); + temp = er32(COLC); + temp = er32(DC); + temp = er32(SEC); + temp = er32(RLEC); + temp = er32(XONRXC); + temp = er32(XONTXC); + temp = er32(XOFFRXC); + temp = er32(XOFFTXC); + temp = er32(FCRUC); + + temp = er32(PRC64); + temp = er32(PRC127); + temp = er32(PRC255); + temp = er32(PRC511); + temp = er32(PRC1023); + temp = er32(PRC1522); + + temp = er32(GPRC); + temp = er32(BPRC); + temp = er32(MPRC); + temp = er32(GPTC); + temp = er32(GORCL); + temp = er32(GORCH); + temp = er32(GOTCL); + temp = er32(GOTCH); + temp = er32(RNBC); + temp = er32(RUC); + temp = er32(RFC); + temp = er32(ROC); + temp = er32(RJC); + temp = er32(TORL); + temp = er32(TORH); + temp = er32(TOTL); + temp = er32(TOTH); + temp = er32(TPR); + temp = er32(TPT); + + temp = er32(PTC64); + temp = er32(PTC127); + temp = er32(PTC255); + temp = er32(PTC511); + temp = er32(PTC1023); + temp = er32(PTC1522); + + temp = er32(MPTC); + temp = er32(BPTC); + + if (hw->mac_type < e1000_82543) + return; + + temp = er32(ALGNERRC); + temp = er32(RXERRC); + temp = er32(TNCRS); + temp = er32(CEXTERR); + temp = er32(TSCTC); + temp = er32(TSCTFC); + + if (hw->mac_type <= e1000_82544) + return; + + temp = er32(MGTPRC); + temp = er32(MGTPDC); + temp = er32(MGTPTC); +} + +/** + * e1000_reset_adaptive - Resets Adaptive IFS to its default state. + * @hw: Struct containing variables accessed by shared code * * Call this after e1000_init_hw. You may override the IFS defaults by setting * hw->ifs_params_forced to true. However, you must initialize hw-> * current_ifs_val, ifs_min_val, ifs_max_val, ifs_step_size, and ifs_ratio * before calling this function. - *****************************************************************************/ + */ void e1000_reset_adaptive(struct e1000_hw *hw) { - DEBUGFUNC("e1000_reset_adaptive"); - - if (hw->adaptive_ifs) { - if (!hw->ifs_params_forced) { - hw->current_ifs_val = 0; - hw->ifs_min_val = IFS_MIN; - hw->ifs_max_val = IFS_MAX; - hw->ifs_step_size = IFS_STEP; - hw->ifs_ratio = IFS_RATIO; - } - hw->in_ifs_mode = false; - ew32(AIT, 0); - } else { - DEBUGOUT("Not in Adaptive IFS mode!\n"); - } + DEBUGFUNC("e1000_reset_adaptive"); + + if (hw->adaptive_ifs) { + if (!hw->ifs_params_forced) { + hw->current_ifs_val = 0; + hw->ifs_min_val = IFS_MIN; + hw->ifs_max_val = IFS_MAX; + hw->ifs_step_size = IFS_STEP; + hw->ifs_ratio = IFS_RATIO; + } + hw->in_ifs_mode = false; + ew32(AIT, 0); + } else { + DEBUGOUT("Not in Adaptive IFS mode!\n"); + } } -/****************************************************************************** +/** + * e1000_update_adaptive - update adaptive IFS + * @hw: Struct containing variables accessed by shared code + * @tx_packets: Number of transmits since last callback + * @total_collisions: Number of collisions since last callback + * * Called during the callback/watchdog routine to update IFS value based on * the ratio of transmits to collisions. - * - * hw - Struct containing variables accessed by shared code - * tx_packets - Number of transmits since last callback - * total_collisions - Number of collisions since last callback - *****************************************************************************/ + */ void e1000_update_adaptive(struct e1000_hw *hw) { - DEBUGFUNC("e1000_update_adaptive"); - - if (hw->adaptive_ifs) { - if ((hw->collision_delta * hw->ifs_ratio) > hw->tx_packet_delta) { - if (hw->tx_packet_delta > MIN_NUM_XMITS) { - hw->in_ifs_mode = true; - if (hw->current_ifs_val < hw->ifs_max_val) { - if (hw->current_ifs_val == 0) - hw->current_ifs_val = hw->ifs_min_val; - else - hw->current_ifs_val += hw->ifs_step_size; - ew32(AIT, hw->current_ifs_val); - } - } - } else { - if (hw->in_ifs_mode && (hw->tx_packet_delta <= MIN_NUM_XMITS)) { - hw->current_ifs_val = 0; - hw->in_ifs_mode = false; - ew32(AIT, 0); - } - } - } else { - DEBUGOUT("Not in Adaptive IFS mode!\n"); - } + DEBUGFUNC("e1000_update_adaptive"); + + if (hw->adaptive_ifs) { + if ((hw->collision_delta *hw->ifs_ratio) > hw->tx_packet_delta) { + if (hw->tx_packet_delta > MIN_NUM_XMITS) { + hw->in_ifs_mode = true; + if (hw->current_ifs_val < hw->ifs_max_val) { + if (hw->current_ifs_val == 0) + hw->current_ifs_val = + hw->ifs_min_val; + else + hw->current_ifs_val += + hw->ifs_step_size; + ew32(AIT, hw->current_ifs_val); + } + } + } else { + if (hw->in_ifs_mode + && (hw->tx_packet_delta <= MIN_NUM_XMITS)) { + hw->current_ifs_val = 0; + hw->in_ifs_mode = false; + ew32(AIT, 0); + } + } + } else { + DEBUGOUT("Not in Adaptive IFS mode!\n"); + } } -/****************************************************************************** - * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT +/** + * e1000_tbi_adjust_stats + * @hw: Struct containing variables accessed by shared code + * @frame_len: The length of the frame in question + * @mac_addr: The Ethernet destination address of the frame in question * - * hw - Struct containing variables accessed by shared code - * frame_len - The length of the frame in question - * mac_addr - The Ethernet destination address of the frame in question - *****************************************************************************/ + * Adjusts the statistic counters when a frame is accepted by TBI_ACCEPT + */ void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, u32 frame_len, u8 *mac_addr) { - u64 carry_bit; - - /* First adjust the frame length. */ - frame_len--; - /* We need to adjust the statistics counters, since the hardware - * counters overcount this packet as a CRC error and undercount - * the packet as a good packet - */ - /* This packet should not be counted as a CRC error. */ - stats->crcerrs--; - /* This packet does count as a Good Packet Received. */ - stats->gprc++; - - /* Adjust the Good Octets received counters */ - carry_bit = 0x80000000 & stats->gorcl; - stats->gorcl += frame_len; - /* If the high bit of Gorcl (the low 32 bits of the Good Octets - * Received Count) was one before the addition, - * AND it is zero after, then we lost the carry out, - * need to add one to Gorch (Good Octets Received Count High). - * This could be simplified if all environments supported - * 64-bit integers. - */ - if (carry_bit && ((stats->gorcl & 0x80000000) == 0)) - stats->gorch++; - /* Is this a broadcast or multicast? Check broadcast first, - * since the test for a multicast frame will test positive on - * a broadcast frame. - */ - if ((mac_addr[0] == (u8)0xff) && (mac_addr[1] == (u8)0xff)) - /* Broadcast packet */ - stats->bprc++; - else if (*mac_addr & 0x01) - /* Multicast packet */ - stats->mprc++; - - if (frame_len == hw->max_frame_size) { - /* In this case, the hardware has overcounted the number of - * oversize frames. - */ - if (stats->roc > 0) - stats->roc--; - } - - /* Adjust the bin counters when the extra byte put the frame in the - * wrong bin. Remember that the frame_len was adjusted above. - */ - if (frame_len == 64) { - stats->prc64++; - stats->prc127--; - } else if (frame_len == 127) { - stats->prc127++; - stats->prc255--; - } else if (frame_len == 255) { - stats->prc255++; - stats->prc511--; - } else if (frame_len == 511) { - stats->prc511++; - stats->prc1023--; - } else if (frame_len == 1023) { - stats->prc1023++; - stats->prc1522--; - } else if (frame_len == 1522) { - stats->prc1522++; - } + u64 carry_bit; + + /* First adjust the frame length. */ + frame_len--; + /* We need to adjust the statistics counters, since the hardware + * counters overcount this packet as a CRC error and undercount + * the packet as a good packet + */ + /* This packet should not be counted as a CRC error. */ + stats->crcerrs--; + /* This packet does count as a Good Packet Received. */ + stats->gprc++; + + /* Adjust the Good Octets received counters */ + carry_bit = 0x80000000 & stats->gorcl; + stats->gorcl += frame_len; + /* If the high bit of Gorcl (the low 32 bits of the Good Octets + * Received Count) was one before the addition, + * AND it is zero after, then we lost the carry out, + * need to add one to Gorch (Good Octets Received Count High). + * This could be simplified if all environments supported + * 64-bit integers. + */ + if (carry_bit && ((stats->gorcl & 0x80000000) == 0)) + stats->gorch++; + /* Is this a broadcast or multicast? Check broadcast first, + * since the test for a multicast frame will test positive on + * a broadcast frame. + */ + if ((mac_addr[0] == (u8) 0xff) && (mac_addr[1] == (u8) 0xff)) + /* Broadcast packet */ + stats->bprc++; + else if (*mac_addr & 0x01) + /* Multicast packet */ + stats->mprc++; + + if (frame_len == hw->max_frame_size) { + /* In this case, the hardware has overcounted the number of + * oversize frames. + */ + if (stats->roc > 0) + stats->roc--; + } + + /* Adjust the bin counters when the extra byte put the frame in the + * wrong bin. Remember that the frame_len was adjusted above. + */ + if (frame_len == 64) { + stats->prc64++; + stats->prc127--; + } else if (frame_len == 127) { + stats->prc127++; + stats->prc255--; + } else if (frame_len == 255) { + stats->prc255++; + stats->prc511--; + } else if (frame_len == 511) { + stats->prc511++; + stats->prc1023--; + } else if (frame_len == 1023) { + stats->prc1023++; + stats->prc1522--; + } else if (frame_len == 1522) { + stats->prc1522++; + } } -/****************************************************************************** - * Gets the current PCI bus type, speed, and width of the hardware +/** + * e1000_get_bus_info + * @hw: Struct containing variables accessed by shared code * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ + * Gets the current PCI bus type, speed, and width of the hardware + */ void e1000_get_bus_info(struct e1000_hw *hw) { - s32 ret_val; - u16 pci_ex_link_status; - u32 status; - - switch (hw->mac_type) { - case e1000_82542_rev2_0: - case e1000_82542_rev2_1: - hw->bus_type = e1000_bus_type_pci; - hw->bus_speed = e1000_bus_speed_unknown; - hw->bus_width = e1000_bus_width_unknown; - break; - case e1000_82571: - case e1000_82572: - case e1000_82573: - case e1000_80003es2lan: - hw->bus_type = e1000_bus_type_pci_express; - hw->bus_speed = e1000_bus_speed_2500; - ret_val = e1000_read_pcie_cap_reg(hw, - PCI_EX_LINK_STATUS, - &pci_ex_link_status); - if (ret_val) - hw->bus_width = e1000_bus_width_unknown; - else - hw->bus_width = (pci_ex_link_status & PCI_EX_LINK_WIDTH_MASK) >> - PCI_EX_LINK_WIDTH_SHIFT; - break; - case e1000_ich8lan: - hw->bus_type = e1000_bus_type_pci_express; - hw->bus_speed = e1000_bus_speed_2500; - hw->bus_width = e1000_bus_width_pciex_1; - break; - default: - status = er32(STATUS); - hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ? - e1000_bus_type_pcix : e1000_bus_type_pci; - - if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) { - hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ? - e1000_bus_speed_66 : e1000_bus_speed_120; - } else if (hw->bus_type == e1000_bus_type_pci) { - hw->bus_speed = (status & E1000_STATUS_PCI66) ? - e1000_bus_speed_66 : e1000_bus_speed_33; - } else { - switch (status & E1000_STATUS_PCIX_SPEED) { - case E1000_STATUS_PCIX_SPEED_66: - hw->bus_speed = e1000_bus_speed_66; - break; - case E1000_STATUS_PCIX_SPEED_100: - hw->bus_speed = e1000_bus_speed_100; - break; - case E1000_STATUS_PCIX_SPEED_133: - hw->bus_speed = e1000_bus_speed_133; - break; - default: - hw->bus_speed = e1000_bus_speed_reserved; - break; - } - } - hw->bus_width = (status & E1000_STATUS_BUS64) ? - e1000_bus_width_64 : e1000_bus_width_32; - break; - } + u32 status; + + switch (hw->mac_type) { + case e1000_82542_rev2_0: + case e1000_82542_rev2_1: + hw->bus_type = e1000_bus_type_pci; + hw->bus_speed = e1000_bus_speed_unknown; + hw->bus_width = e1000_bus_width_unknown; + break; + default: + status = er32(STATUS); + hw->bus_type = (status & E1000_STATUS_PCIX_MODE) ? + e1000_bus_type_pcix : e1000_bus_type_pci; + + if (hw->device_id == E1000_DEV_ID_82546EB_QUAD_COPPER) { + hw->bus_speed = (hw->bus_type == e1000_bus_type_pci) ? + e1000_bus_speed_66 : e1000_bus_speed_120; + } else if (hw->bus_type == e1000_bus_type_pci) { + hw->bus_speed = (status & E1000_STATUS_PCI66) ? + e1000_bus_speed_66 : e1000_bus_speed_33; + } else { + switch (status & E1000_STATUS_PCIX_SPEED) { + case E1000_STATUS_PCIX_SPEED_66: + hw->bus_speed = e1000_bus_speed_66; + break; + case E1000_STATUS_PCIX_SPEED_100: + hw->bus_speed = e1000_bus_speed_100; + break; + case E1000_STATUS_PCIX_SPEED_133: + hw->bus_speed = e1000_bus_speed_133; + break; + default: + hw->bus_speed = e1000_bus_speed_reserved; + break; + } + } + hw->bus_width = (status & E1000_STATUS_BUS64) ? + e1000_bus_width_64 : e1000_bus_width_32; + break; + } } -/****************************************************************************** +/** + * e1000_write_reg_io + * @hw: Struct containing variables accessed by shared code + * @offset: offset to write to + * @value: value to write + * * Writes a value to one of the devices registers using port I/O (as opposed to * memory mapped I/O). Only 82544 and newer devices support port I/O. - * - * hw - Struct containing variables accessed by shared code - * offset - offset to write to - * value - value to write - *****************************************************************************/ + */ static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value) { - unsigned long io_addr = hw->io_base; - unsigned long io_data = hw->io_base + 4; + unsigned long io_addr = hw->io_base; + unsigned long io_data = hw->io_base + 4; - e1000_io_write(hw, io_addr, offset); - e1000_io_write(hw, io_data, value); + e1000_io_write(hw, io_addr, offset); + e1000_io_write(hw, io_data, value); } -/****************************************************************************** - * Estimates the cable length. - * - * hw - Struct containing variables accessed by shared code - * min_length - The estimated minimum length - * max_length - The estimated maximum length +/** + * e1000_get_cable_length - Estimates the cable length. + * @hw: Struct containing variables accessed by shared code + * @min_length: The estimated minimum length + * @max_length: The estimated maximum length * * returns: - E1000_ERR_XXX * E1000_SUCCESS @@ -6528,185 +4842,115 @@ static void e1000_write_reg_io(struct e1000_hw *hw, u32 offset, u32 value) * So for M88 phy's, this function interprets the one value returned from the * register to the minimum and maximum range. * For IGP phy's, the function calculates the range by the AGC registers. - *****************************************************************************/ + */ static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length, u16 *max_length) { - s32 ret_val; - u16 agc_value = 0; - u16 i, phy_data; - u16 cable_length; - - DEBUGFUNC("e1000_get_cable_length"); - - *min_length = *max_length = 0; - - /* Use old method for Phy older than IGP */ - if (hw->phy_type == e1000_phy_m88) { - - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, - &phy_data); - if (ret_val) - return ret_val; - cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> - M88E1000_PSSR_CABLE_LENGTH_SHIFT; - - /* Convert the enum value to ranged values */ - switch (cable_length) { - case e1000_cable_length_50: - *min_length = 0; - *max_length = e1000_igp_cable_length_50; - break; - case e1000_cable_length_50_80: - *min_length = e1000_igp_cable_length_50; - *max_length = e1000_igp_cable_length_80; - break; - case e1000_cable_length_80_110: - *min_length = e1000_igp_cable_length_80; - *max_length = e1000_igp_cable_length_110; - break; - case e1000_cable_length_110_140: - *min_length = e1000_igp_cable_length_110; - *max_length = e1000_igp_cable_length_140; - break; - case e1000_cable_length_140: - *min_length = e1000_igp_cable_length_140; - *max_length = e1000_igp_cable_length_170; - break; - default: - return -E1000_ERR_PHY; - break; - } - } else if (hw->phy_type == e1000_phy_gg82563) { - ret_val = e1000_read_phy_reg(hw, GG82563_PHY_DSP_DISTANCE, - &phy_data); - if (ret_val) - return ret_val; - cable_length = phy_data & GG82563_DSPD_CABLE_LENGTH; - - switch (cable_length) { - case e1000_gg_cable_length_60: - *min_length = 0; - *max_length = e1000_igp_cable_length_60; - break; - case e1000_gg_cable_length_60_115: - *min_length = e1000_igp_cable_length_60; - *max_length = e1000_igp_cable_length_115; - break; - case e1000_gg_cable_length_115_150: - *min_length = e1000_igp_cable_length_115; - *max_length = e1000_igp_cable_length_150; - break; - case e1000_gg_cable_length_150: - *min_length = e1000_igp_cable_length_150; - *max_length = e1000_igp_cable_length_180; - break; - default: - return -E1000_ERR_PHY; - break; - } - } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */ - u16 cur_agc_value; - u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE; - u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = - {IGP01E1000_PHY_AGC_A, - IGP01E1000_PHY_AGC_B, - IGP01E1000_PHY_AGC_C, - IGP01E1000_PHY_AGC_D}; - /* Read the AGC registers for all channels */ - for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { - - ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data); - if (ret_val) - return ret_val; - - cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT; - - /* Value bound check. */ - if ((cur_agc_value >= IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) || - (cur_agc_value == 0)) - return -E1000_ERR_PHY; - - agc_value += cur_agc_value; - - /* Update minimal AGC value. */ - if (min_agc_value > cur_agc_value) - min_agc_value = cur_agc_value; - } - - /* Remove the minimal AGC result for length < 50m */ - if (agc_value < IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) { - agc_value -= min_agc_value; - - /* Get the average length of the remaining 3 channels */ - agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1); - } else { - /* Get the average length of all the 4 channels. */ - agc_value /= IGP01E1000_PHY_CHANNEL_NUM; - } - - /* Set the range of the calculated length. */ - *min_length = ((e1000_igp_cable_length_table[agc_value] - - IGP01E1000_AGC_RANGE) > 0) ? - (e1000_igp_cable_length_table[agc_value] - - IGP01E1000_AGC_RANGE) : 0; - *max_length = e1000_igp_cable_length_table[agc_value] + - IGP01E1000_AGC_RANGE; - } else if (hw->phy_type == e1000_phy_igp_2 || - hw->phy_type == e1000_phy_igp_3) { - u16 cur_agc_index, max_agc_index = 0; - u16 min_agc_index = IGP02E1000_AGC_LENGTH_TABLE_SIZE - 1; - u16 agc_reg_array[IGP02E1000_PHY_CHANNEL_NUM] = - {IGP02E1000_PHY_AGC_A, - IGP02E1000_PHY_AGC_B, - IGP02E1000_PHY_AGC_C, - IGP02E1000_PHY_AGC_D}; - /* Read the AGC registers for all channels */ - for (i = 0; i < IGP02E1000_PHY_CHANNEL_NUM; i++) { - ret_val = e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data); - if (ret_val) - return ret_val; - - /* Getting bits 15:9, which represent the combination of course and - * fine gain values. The result is a number that can be put into - * the lookup table to obtain the approximate cable length. */ - cur_agc_index = (phy_data >> IGP02E1000_AGC_LENGTH_SHIFT) & - IGP02E1000_AGC_LENGTH_MASK; - - /* Array index bound check. */ - if ((cur_agc_index >= IGP02E1000_AGC_LENGTH_TABLE_SIZE) || - (cur_agc_index == 0)) - return -E1000_ERR_PHY; - - /* Remove min & max AGC values from calculation. */ - if (e1000_igp_2_cable_length_table[min_agc_index] > - e1000_igp_2_cable_length_table[cur_agc_index]) - min_agc_index = cur_agc_index; - if (e1000_igp_2_cable_length_table[max_agc_index] < - e1000_igp_2_cable_length_table[cur_agc_index]) - max_agc_index = cur_agc_index; - - agc_value += e1000_igp_2_cable_length_table[cur_agc_index]; - } - - agc_value -= (e1000_igp_2_cable_length_table[min_agc_index] + - e1000_igp_2_cable_length_table[max_agc_index]); - agc_value /= (IGP02E1000_PHY_CHANNEL_NUM - 2); - - /* Calculate cable length with the error range of +/- 10 meters. */ - *min_length = ((agc_value - IGP02E1000_AGC_RANGE) > 0) ? - (agc_value - IGP02E1000_AGC_RANGE) : 0; - *max_length = agc_value + IGP02E1000_AGC_RANGE; - } - - return E1000_SUCCESS; + s32 ret_val; + u16 agc_value = 0; + u16 i, phy_data; + u16 cable_length; + + DEBUGFUNC("e1000_get_cable_length"); + + *min_length = *max_length = 0; + + /* Use old method for Phy older than IGP */ + if (hw->phy_type == e1000_phy_m88) { + + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, + &phy_data); + if (ret_val) + return ret_val; + cable_length = (phy_data & M88E1000_PSSR_CABLE_LENGTH) >> + M88E1000_PSSR_CABLE_LENGTH_SHIFT; + + /* Convert the enum value to ranged values */ + switch (cable_length) { + case e1000_cable_length_50: + *min_length = 0; + *max_length = e1000_igp_cable_length_50; + break; + case e1000_cable_length_50_80: + *min_length = e1000_igp_cable_length_50; + *max_length = e1000_igp_cable_length_80; + break; + case e1000_cable_length_80_110: + *min_length = e1000_igp_cable_length_80; + *max_length = e1000_igp_cable_length_110; + break; + case e1000_cable_length_110_140: + *min_length = e1000_igp_cable_length_110; + *max_length = e1000_igp_cable_length_140; + break; + case e1000_cable_length_140: + *min_length = e1000_igp_cable_length_140; + *max_length = e1000_igp_cable_length_170; + break; + default: + return -E1000_ERR_PHY; + break; + } + } else if (hw->phy_type == e1000_phy_igp) { /* For IGP PHY */ + u16 cur_agc_value; + u16 min_agc_value = IGP01E1000_AGC_LENGTH_TABLE_SIZE; + u16 agc_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = + { IGP01E1000_PHY_AGC_A, + IGP01E1000_PHY_AGC_B, + IGP01E1000_PHY_AGC_C, + IGP01E1000_PHY_AGC_D + }; + /* Read the AGC registers for all channels */ + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + + ret_val = + e1000_read_phy_reg(hw, agc_reg_array[i], &phy_data); + if (ret_val) + return ret_val; + + cur_agc_value = phy_data >> IGP01E1000_AGC_LENGTH_SHIFT; + + /* Value bound check. */ + if ((cur_agc_value >= + IGP01E1000_AGC_LENGTH_TABLE_SIZE - 1) + || (cur_agc_value == 0)) + return -E1000_ERR_PHY; + + agc_value += cur_agc_value; + + /* Update minimal AGC value. */ + if (min_agc_value > cur_agc_value) + min_agc_value = cur_agc_value; + } + + /* Remove the minimal AGC result for length < 50m */ + if (agc_value < + IGP01E1000_PHY_CHANNEL_NUM * e1000_igp_cable_length_50) { + agc_value -= min_agc_value; + + /* Get the average length of the remaining 3 channels */ + agc_value /= (IGP01E1000_PHY_CHANNEL_NUM - 1); + } else { + /* Get the average length of all the 4 channels. */ + agc_value /= IGP01E1000_PHY_CHANNEL_NUM; + } + + /* Set the range of the calculated length. */ + *min_length = ((e1000_igp_cable_length_table[agc_value] - + IGP01E1000_AGC_RANGE) > 0) ? + (e1000_igp_cable_length_table[agc_value] - + IGP01E1000_AGC_RANGE) : 0; + *max_length = e1000_igp_cable_length_table[agc_value] + + IGP01E1000_AGC_RANGE; + } + + return E1000_SUCCESS; } -/****************************************************************************** - * Check the cable polarity - * - * hw - Struct containing variables accessed by shared code - * polarity - output parameter : 0 - Polarity is not reversed +/** + * e1000_check_polarity - Check the cable polarity + * @hw: Struct containing variables accessed by shared code + * @polarity: output parameter : 0 - Polarity is not reversed * 1 - Polarity is reversed. * * returns: - E1000_ERR_XXX @@ -6717,73 +4961,65 @@ static s32 e1000_get_cable_length(struct e1000_hw *hw, u16 *min_length, * 10 Mbps. If the link speed is 100 Mbps there is no polarity so this bit will * return 0. If the link speed is 1000 Mbps the polarity status is in the * IGP01E1000_PHY_PCS_INIT_REG. - *****************************************************************************/ + */ static s32 e1000_check_polarity(struct e1000_hw *hw, e1000_rev_polarity *polarity) { - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_check_polarity"); - - if ((hw->phy_type == e1000_phy_m88) || - (hw->phy_type == e1000_phy_gg82563)) { - /* return the Polarity bit in the Status register. */ - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, - &phy_data); - if (ret_val) - return ret_val; - *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >> - M88E1000_PSSR_REV_POLARITY_SHIFT) ? - e1000_rev_polarity_reversed : e1000_rev_polarity_normal; - - } else if (hw->phy_type == e1000_phy_igp || - hw->phy_type == e1000_phy_igp_3 || - hw->phy_type == e1000_phy_igp_2) { - /* Read the Status register to check the speed */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to - * find the polarity status */ - if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == - IGP01E1000_PSSR_SPEED_1000MBPS) { - - /* Read the GIG initialization PCS register (0x00B4) */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG, - &phy_data); - if (ret_val) - return ret_val; - - /* Check the polarity bits */ - *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ? - e1000_rev_polarity_reversed : e1000_rev_polarity_normal; - } else { - /* For 10 Mbps, read the polarity bit in the status register. (for - * 100 Mbps this bit is always 0) */ - *polarity = (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ? - e1000_rev_polarity_reversed : e1000_rev_polarity_normal; - } - } else if (hw->phy_type == e1000_phy_ife) { - ret_val = e1000_read_phy_reg(hw, IFE_PHY_EXTENDED_STATUS_CONTROL, - &phy_data); - if (ret_val) - return ret_val; - *polarity = ((phy_data & IFE_PESC_POLARITY_REVERSED) >> - IFE_PESC_POLARITY_REVERSED_SHIFT) ? - e1000_rev_polarity_reversed : e1000_rev_polarity_normal; - } - return E1000_SUCCESS; + s32 ret_val; + u16 phy_data; + + DEBUGFUNC("e1000_check_polarity"); + + if (hw->phy_type == e1000_phy_m88) { + /* return the Polarity bit in the Status register. */ + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, + &phy_data); + if (ret_val) + return ret_val; + *polarity = ((phy_data & M88E1000_PSSR_REV_POLARITY) >> + M88E1000_PSSR_REV_POLARITY_SHIFT) ? + e1000_rev_polarity_reversed : e1000_rev_polarity_normal; + + } else if (hw->phy_type == e1000_phy_igp) { + /* Read the Status register to check the speed */ + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_STATUS, + &phy_data); + if (ret_val) + return ret_val; + + /* If speed is 1000 Mbps, must read the IGP01E1000_PHY_PCS_INIT_REG to + * find the polarity status */ + if ((phy_data & IGP01E1000_PSSR_SPEED_MASK) == + IGP01E1000_PSSR_SPEED_1000MBPS) { + + /* Read the GIG initialization PCS register (0x00B4) */ + ret_val = + e1000_read_phy_reg(hw, IGP01E1000_PHY_PCS_INIT_REG, + &phy_data); + if (ret_val) + return ret_val; + + /* Check the polarity bits */ + *polarity = (phy_data & IGP01E1000_PHY_POLARITY_MASK) ? + e1000_rev_polarity_reversed : + e1000_rev_polarity_normal; + } else { + /* For 10 Mbps, read the polarity bit in the status register. (for + * 100 Mbps this bit is always 0) */ + *polarity = + (phy_data & IGP01E1000_PSSR_POLARITY_REVERSED) ? + e1000_rev_polarity_reversed : + e1000_rev_polarity_normal; + } + } + return E1000_SUCCESS; } -/****************************************************************************** - * Check if Downshift occured - * - * hw - Struct containing variables accessed by shared code - * downshift - output parameter : 0 - No Downshift ocured. - * 1 - Downshift ocured. +/** + * e1000_check_downshift - Check if Downshift occurred + * @hw: Struct containing variables accessed by shared code + * @downshift: output parameter : 0 - No Downshift occurred. + * 1 - Downshift occurred. * * returns: - E1000_ERR_XXX * E1000_SUCCESS @@ -6792,2041 +5028,607 @@ static s32 e1000_check_polarity(struct e1000_hw *hw, * Specific Status register. For IGP phy's, it reads the Downgrade bit in the * Link Health register. In IGP this bit is latched high, so the driver must * read it immediately after link is established. - *****************************************************************************/ + */ static s32 e1000_check_downshift(struct e1000_hw *hw) { - s32 ret_val; - u16 phy_data; - - DEBUGFUNC("e1000_check_downshift"); - - if (hw->phy_type == e1000_phy_igp || - hw->phy_type == e1000_phy_igp_3 || - hw->phy_type == e1000_phy_igp_2) { - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH, - &phy_data); - if (ret_val) - return ret_val; - - hw->speed_downgraded = (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0; - } else if ((hw->phy_type == e1000_phy_m88) || - (hw->phy_type == e1000_phy_gg82563)) { - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >> - M88E1000_PSSR_DOWNSHIFT_SHIFT; - } else if (hw->phy_type == e1000_phy_ife) { - /* e1000_phy_ife supports 10/100 speed only */ - hw->speed_downgraded = false; - } - - return E1000_SUCCESS; -} + s32 ret_val; + u16 phy_data; -/***************************************************************************** - * - * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a - * gigabit link is achieved to improve link quality. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_PHY if fail to read/write the PHY - * E1000_SUCCESS at any other case. - * - ****************************************************************************/ + DEBUGFUNC("e1000_check_downshift"); -static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) -{ - s32 ret_val; - u16 phy_data, phy_saved_data, speed, duplex, i; - u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = - {IGP01E1000_PHY_AGC_PARAM_A, - IGP01E1000_PHY_AGC_PARAM_B, - IGP01E1000_PHY_AGC_PARAM_C, - IGP01E1000_PHY_AGC_PARAM_D}; - u16 min_length, max_length; - - DEBUGFUNC("e1000_config_dsp_after_link_change"); - - if (hw->phy_type != e1000_phy_igp) - return E1000_SUCCESS; - - if (link_up) { - ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); - if (ret_val) { - DEBUGOUT("Error getting link speed and duplex\n"); - return ret_val; - } - - if (speed == SPEED_1000) { - - ret_val = e1000_get_cable_length(hw, &min_length, &max_length); - if (ret_val) - return ret_val; - - if ((hw->dsp_config_state == e1000_dsp_config_enabled) && - min_length >= e1000_igp_cable_length_50) { - - for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { - ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; - - ret_val = e1000_write_phy_reg(hw, dsp_reg_array[i], - phy_data); - if (ret_val) - return ret_val; - } - hw->dsp_config_state = e1000_dsp_config_activated; - } - - if ((hw->ffe_config_state == e1000_ffe_config_enabled) && - (min_length < e1000_igp_cable_length_50)) { - - u16 ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_20; - u32 idle_errs = 0; - - /* clear previous idle error counts */ - ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - for (i = 0; i < ffe_idle_err_timeout; i++) { - udelay(1000); - ret_val = e1000_read_phy_reg(hw, PHY_1000T_STATUS, - &phy_data); - if (ret_val) - return ret_val; - - idle_errs += (phy_data & SR_1000T_IDLE_ERROR_CNT); - if (idle_errs > SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) { - hw->ffe_config_state = e1000_ffe_config_active; - - ret_val = e1000_write_phy_reg(hw, - IGP01E1000_PHY_DSP_FFE, - IGP01E1000_PHY_DSP_FFE_CM_CP); - if (ret_val) - return ret_val; - break; - } - - if (idle_errs) - ffe_idle_err_timeout = FFE_IDLE_ERR_COUNT_TIMEOUT_100; - } - } - } - } else { - if (hw->dsp_config_state == e1000_dsp_config_activated) { - /* Save off the current value of register 0x2F5B to be restored at - * the end of the routines. */ - ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); - - if (ret_val) - return ret_val; - - /* Disable the PHY transmitter */ - ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003); - - if (ret_val) - return ret_val; - - mdelay(20); - - ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_FORCE_GIGA); - if (ret_val) - return ret_val; - for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { - ret_val = e1000_read_phy_reg(hw, dsp_reg_array[i], &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; - phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS; - - ret_val = e1000_write_phy_reg(hw,dsp_reg_array[i], phy_data); - if (ret_val) - return ret_val; - } - - ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_RESTART_AUTONEG); - if (ret_val) - return ret_val; - - mdelay(20); - - /* Now enable the transmitter */ - ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); - - if (ret_val) - return ret_val; - - hw->dsp_config_state = e1000_dsp_config_enabled; - } - - if (hw->ffe_config_state == e1000_ffe_config_active) { - /* Save off the current value of register 0x2F5B to be restored at - * the end of the routines. */ - ret_val = e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); - - if (ret_val) - return ret_val; - - /* Disable the PHY transmitter */ - ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003); - - if (ret_val) - return ret_val; - - mdelay(20); - - ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_FORCE_GIGA); - if (ret_val) - return ret_val; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE, - IGP01E1000_PHY_DSP_FFE_DEFAULT); - if (ret_val) - return ret_val; - - ret_val = e1000_write_phy_reg(hw, 0x0000, - IGP01E1000_IEEE_RESTART_AUTONEG); - if (ret_val) - return ret_val; - - mdelay(20); - - /* Now enable the transmitter */ - ret_val = e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); - - if (ret_val) - return ret_val; - - hw->ffe_config_state = e1000_ffe_config_enabled; - } - } - return E1000_SUCCESS; -} + if (hw->phy_type == e1000_phy_igp) { + ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH, + &phy_data); + if (ret_val) + return ret_val; -/***************************************************************************** - * Set PHY to class A mode - * Assumes the following operations will follow to enable the new class mode. - * 1. Do a PHY soft reset - * 2. Restart auto-negotiation or force link. - * - * hw - Struct containing variables accessed by shared code - ****************************************************************************/ -static s32 e1000_set_phy_mode(struct e1000_hw *hw) -{ - s32 ret_val; - u16 eeprom_data; - - DEBUGFUNC("e1000_set_phy_mode"); - - if ((hw->mac_type == e1000_82545_rev_3) && - (hw->media_type == e1000_media_type_copper)) { - ret_val = e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, &eeprom_data); - if (ret_val) { - return ret_val; - } - - if ((eeprom_data != EEPROM_RESERVED_WORD) && - (eeprom_data & EEPROM_PHY_CLASS_A)) { - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x000B); - if (ret_val) - return ret_val; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x8104); - if (ret_val) - return ret_val; - - hw->phy_reset_disable = false; - } - } - - return E1000_SUCCESS; -} + hw->speed_downgraded = + (phy_data & IGP01E1000_PLHR_SS_DOWNGRADE) ? 1 : 0; + } else if (hw->phy_type == e1000_phy_m88) { + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, + &phy_data); + if (ret_val) + return ret_val; -/***************************************************************************** - * - * This function sets the lplu state according to the active flag. When - * activating lplu this function also disables smart speed and vise versa. - * lplu will not be activated unless the device autonegotiation advertisment - * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. - * hw: Struct containing variables accessed by shared code - * active - true to enable lplu false to disable lplu. - * - * returns: - E1000_ERR_PHY if fail to read/write the PHY - * E1000_SUCCESS at any other case. - * - ****************************************************************************/ + hw->speed_downgraded = (phy_data & M88E1000_PSSR_DOWNSHIFT) >> + M88E1000_PSSR_DOWNSHIFT_SHIFT; + } -static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active) -{ - u32 phy_ctrl = 0; - s32 ret_val; - u16 phy_data; - DEBUGFUNC("e1000_set_d3_lplu_state"); - - if (hw->phy_type != e1000_phy_igp && hw->phy_type != e1000_phy_igp_2 - && hw->phy_type != e1000_phy_igp_3) - return E1000_SUCCESS; - - /* During driver activity LPLU should not be used or it will attain link - * from the lowest speeds starting from 10Mbps. The capability is used for - * Dx transitions and states */ - if (hw->mac_type == e1000_82541_rev_2 || hw->mac_type == e1000_82547_rev_2) { - ret_val = e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data); - if (ret_val) - return ret_val; - } else if (hw->mac_type == e1000_ich8lan) { - /* MAC writes into PHY register based on the state transition - * and start auto-negotiation. SW driver can overwrite the settings - * in CSR PHY power control E1000_PHY_CTRL register. */ - phy_ctrl = er32(PHY_CTRL); - } else { - ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); - if (ret_val) - return ret_val; - } - - if (!active) { - if (hw->mac_type == e1000_82541_rev_2 || - hw->mac_type == e1000_82547_rev_2) { - phy_data &= ~IGP01E1000_GMII_FLEX_SPD; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data); - if (ret_val) - return ret_val; - } else { - if (hw->mac_type == e1000_ich8lan) { - phy_ctrl &= ~E1000_PHY_CTRL_NOND0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - } else { - phy_data &= ~IGP02E1000_PM_D3_LPLU; - ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, - phy_data); - if (ret_val) - return ret_val; - } - } - - /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during - * Dx states where the power conservation is most important. During - * driver activity we should enable SmartSpeed, so performance is - * maintained. */ - if (hw->smart_speed == e1000_smart_speed_on) { - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data |= IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } else if (hw->smart_speed == e1000_smart_speed_off) { - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } - - } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) || - (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL ) || - (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_100_ALL)) { - - if (hw->mac_type == e1000_82541_rev_2 || - hw->mac_type == e1000_82547_rev_2) { - phy_data |= IGP01E1000_GMII_FLEX_SPD; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, phy_data); - if (ret_val) - return ret_val; - } else { - if (hw->mac_type == e1000_ich8lan) { - phy_ctrl |= E1000_PHY_CTRL_NOND0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - } else { - phy_data |= IGP02E1000_PM_D3_LPLU; - ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, - phy_data); - if (ret_val) - return ret_val; - } - } - - /* When LPLU is enabled we should disable SmartSpeed */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data); - if (ret_val) - return ret_val; - - } - return E1000_SUCCESS; + return E1000_SUCCESS; } -/***************************************************************************** - * - * This function sets the lplu d0 state according to the active flag. When - * activating lplu this function also disables smart speed and vise versa. - * lplu will not be activated unless the device autonegotiation advertisment - * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. - * hw: Struct containing variables accessed by shared code - * active - true to enable lplu false to disable lplu. +/** + * e1000_config_dsp_after_link_change + * @hw: Struct containing variables accessed by shared code + * @link_up: was link up at the time this was called * * returns: - E1000_ERR_PHY if fail to read/write the PHY * E1000_SUCCESS at any other case. * - ****************************************************************************/ - -static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active) -{ - u32 phy_ctrl = 0; - s32 ret_val; - u16 phy_data; - DEBUGFUNC("e1000_set_d0_lplu_state"); - - if (hw->mac_type <= e1000_82547_rev_2) - return E1000_SUCCESS; - - if (hw->mac_type == e1000_ich8lan) { - phy_ctrl = er32(PHY_CTRL); - } else { - ret_val = e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, &phy_data); - if (ret_val) - return ret_val; - } - - if (!active) { - if (hw->mac_type == e1000_ich8lan) { - phy_ctrl &= ~E1000_PHY_CTRL_D0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - } else { - phy_data &= ~IGP02E1000_PM_D0_LPLU; - ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); - if (ret_val) - return ret_val; - } - - /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during - * Dx states where the power conservation is most important. During - * driver activity we should enable SmartSpeed, so performance is - * maintained. */ - if (hw->smart_speed == e1000_smart_speed_on) { - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data |= IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } else if (hw->smart_speed == e1000_smart_speed_off) { - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, - phy_data); - if (ret_val) - return ret_val; - } - - - } else { - - if (hw->mac_type == e1000_ich8lan) { - phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU; - ew32(PHY_CTRL, phy_ctrl); - } else { - phy_data |= IGP02E1000_PM_D0_LPLU; - ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data); - if (ret_val) - return ret_val; - } - - /* When LPLU is enabled we should disable SmartSpeed */ - ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, &phy_data); - if (ret_val) - return ret_val; - - phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; - ret_val = e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, phy_data); - if (ret_val) - return ret_val; - - } - return E1000_SUCCESS; -} + * 82541_rev_2 & 82547_rev_2 have the capability to configure the DSP when a + * gigabit link is achieved to improve link quality. + */ -/****************************************************************************** - * Change VCO speed register to improve Bit Error Rate performance of SERDES. - * - * hw - Struct containing variables accessed by shared code - *****************************************************************************/ -static s32 e1000_set_vco_speed(struct e1000_hw *hw) +static s32 e1000_config_dsp_after_link_change(struct e1000_hw *hw, bool link_up) { - s32 ret_val; - u16 default_page = 0; - u16 phy_data; - - DEBUGFUNC("e1000_set_vco_speed"); + s32 ret_val; + u16 phy_data, phy_saved_data, speed, duplex, i; + u16 dsp_reg_array[IGP01E1000_PHY_CHANNEL_NUM] = + { IGP01E1000_PHY_AGC_PARAM_A, + IGP01E1000_PHY_AGC_PARAM_B, + IGP01E1000_PHY_AGC_PARAM_C, + IGP01E1000_PHY_AGC_PARAM_D + }; + u16 min_length, max_length; + + DEBUGFUNC("e1000_config_dsp_after_link_change"); + + if (hw->phy_type != e1000_phy_igp) + return E1000_SUCCESS; + + if (link_up) { + ret_val = e1000_get_speed_and_duplex(hw, &speed, &duplex); + if (ret_val) { + DEBUGOUT("Error getting link speed and duplex\n"); + return ret_val; + } - switch (hw->mac_type) { - case e1000_82545_rev_3: - case e1000_82546_rev_3: - break; - default: - return E1000_SUCCESS; - } + if (speed == SPEED_1000) { + + ret_val = + e1000_get_cable_length(hw, &min_length, + &max_length); + if (ret_val) + return ret_val; + + if ((hw->dsp_config_state == e1000_dsp_config_enabled) + && min_length >= e1000_igp_cable_length_50) { + + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + ret_val = + e1000_read_phy_reg(hw, + dsp_reg_array[i], + &phy_data); + if (ret_val) + return ret_val; + + phy_data &= + ~IGP01E1000_PHY_EDAC_MU_INDEX; + + ret_val = + e1000_write_phy_reg(hw, + dsp_reg_array + [i], phy_data); + if (ret_val) + return ret_val; + } + hw->dsp_config_state = + e1000_dsp_config_activated; + } + + if ((hw->ffe_config_state == e1000_ffe_config_enabled) + && (min_length < e1000_igp_cable_length_50)) { + + u16 ffe_idle_err_timeout = + FFE_IDLE_ERR_COUNT_TIMEOUT_20; + u32 idle_errs = 0; + + /* clear previous idle error counts */ + ret_val = + e1000_read_phy_reg(hw, PHY_1000T_STATUS, + &phy_data); + if (ret_val) + return ret_val; + + for (i = 0; i < ffe_idle_err_timeout; i++) { + udelay(1000); + ret_val = + e1000_read_phy_reg(hw, + PHY_1000T_STATUS, + &phy_data); + if (ret_val) + return ret_val; + + idle_errs += + (phy_data & + SR_1000T_IDLE_ERROR_CNT); + if (idle_errs > + SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT) + { + hw->ffe_config_state = + e1000_ffe_config_active; + + ret_val = + e1000_write_phy_reg(hw, + IGP01E1000_PHY_DSP_FFE, + IGP01E1000_PHY_DSP_FFE_CM_CP); + if (ret_val) + return ret_val; + break; + } + + if (idle_errs) + ffe_idle_err_timeout = + FFE_IDLE_ERR_COUNT_TIMEOUT_100; + } + } + } + } else { + if (hw->dsp_config_state == e1000_dsp_config_activated) { + /* Save off the current value of register 0x2F5B to be restored at + * the end of the routines. */ + ret_val = + e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); + + if (ret_val) + return ret_val; + + /* Disable the PHY transmitter */ + ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003); + + if (ret_val) + return ret_val; + + mdelay(20); + + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_FORCE_GIGA); + if (ret_val) + return ret_val; + for (i = 0; i < IGP01E1000_PHY_CHANNEL_NUM; i++) { + ret_val = + e1000_read_phy_reg(hw, dsp_reg_array[i], + &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PHY_EDAC_MU_INDEX; + phy_data |= IGP01E1000_PHY_EDAC_SIGN_EXT_9_BITS; + + ret_val = + e1000_write_phy_reg(hw, dsp_reg_array[i], + phy_data); + if (ret_val) + return ret_val; + } + + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_RESTART_AUTONEG); + if (ret_val) + return ret_val; + + mdelay(20); + + /* Now enable the transmitter */ + ret_val = + e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); + + if (ret_val) + return ret_val; + + hw->dsp_config_state = e1000_dsp_config_enabled; + } - /* Set PHY register 30, page 5, bit 8 to 0 */ + if (hw->ffe_config_state == e1000_ffe_config_active) { + /* Save off the current value of register 0x2F5B to be restored at + * the end of the routines. */ + ret_val = + e1000_read_phy_reg(hw, 0x2F5B, &phy_saved_data); - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page); - if (ret_val) - return ret_val; + if (ret_val) + return ret_val; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005); - if (ret_val) - return ret_val; + /* Disable the PHY transmitter */ + ret_val = e1000_write_phy_reg(hw, 0x2F5B, 0x0003); - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); - if (ret_val) - return ret_val; + if (ret_val) + return ret_val; - phy_data &= ~M88E1000_PHY_VCO_REG_BIT8; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); - if (ret_val) - return ret_val; + mdelay(20); - /* Set PHY register 30, page 4, bit 11 to 1 */ + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_FORCE_GIGA); + if (ret_val) + return ret_val; + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_PHY_DSP_FFE, + IGP01E1000_PHY_DSP_FFE_DEFAULT); + if (ret_val) + return ret_val; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004); - if (ret_val) - return ret_val; + ret_val = e1000_write_phy_reg(hw, 0x0000, + IGP01E1000_IEEE_RESTART_AUTONEG); + if (ret_val) + return ret_val; - ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); - if (ret_val) - return ret_val; + mdelay(20); - phy_data |= M88E1000_PHY_VCO_REG_BIT11; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); - if (ret_val) - return ret_val; + /* Now enable the transmitter */ + ret_val = + e1000_write_phy_reg(hw, 0x2F5B, phy_saved_data); - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page); - if (ret_val) - return ret_val; + if (ret_val) + return ret_val; - return E1000_SUCCESS; + hw->ffe_config_state = e1000_ffe_config_enabled; + } + } + return E1000_SUCCESS; } - -/***************************************************************************** - * This function reads the cookie from ARC ram. +/** + * e1000_set_phy_mode - Set PHY to class A mode + * @hw: Struct containing variables accessed by shared code * - * returns: - E1000_SUCCESS . - ****************************************************************************/ -static s32 e1000_host_if_read_cookie(struct e1000_hw *hw, u8 *buffer) + * Assumes the following operations will follow to enable the new class mode. + * 1. Do a PHY soft reset + * 2. Restart auto-negotiation or force link. + */ +static s32 e1000_set_phy_mode(struct e1000_hw *hw) { - u8 i; - u32 offset = E1000_MNG_DHCP_COOKIE_OFFSET; - u8 length = E1000_MNG_DHCP_COOKIE_LENGTH; - - length = (length >> 2); - offset = (offset >> 2); - - for (i = 0; i < length; i++) { - *((u32 *)buffer + i) = - E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset + i); - } - return E1000_SUCCESS; -} + s32 ret_val; + u16 eeprom_data; + DEBUGFUNC("e1000_set_phy_mode"); -/***************************************************************************** - * This function checks whether the HOST IF is enabled for command operaton - * and also checks whether the previous command is completed. - * It busy waits in case of previous command is not completed. - * - * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or - * timeout - * - E1000_SUCCESS for success. - ****************************************************************************/ -static s32 e1000_mng_enable_host_if(struct e1000_hw *hw) -{ - u32 hicr; - u8 i; - - /* Check that the host interface is enabled. */ - hicr = er32(HICR); - if ((hicr & E1000_HICR_EN) == 0) { - DEBUGOUT("E1000_HOST_EN bit disabled.\n"); - return -E1000_ERR_HOST_INTERFACE_COMMAND; - } - /* check the previous command is completed */ - for (i = 0; i < E1000_MNG_DHCP_COMMAND_TIMEOUT; i++) { - hicr = er32(HICR); - if (!(hicr & E1000_HICR_C)) - break; - mdelay(1); - } - - if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) { - DEBUGOUT("Previous command timeout failed .\n"); - return -E1000_ERR_HOST_INTERFACE_COMMAND; - } - return E1000_SUCCESS; -} + if ((hw->mac_type == e1000_82545_rev_3) && + (hw->media_type == e1000_media_type_copper)) { + ret_val = + e1000_read_eeprom(hw, EEPROM_PHY_CLASS_WORD, 1, + &eeprom_data); + if (ret_val) { + return ret_val; + } -/***************************************************************************** - * This function writes the buffer content at the offset given on the host if. - * It also does alignment considerations to do the writes in most efficient way. - * Also fills up the sum of the buffer in *buffer parameter. - * - * returns - E1000_SUCCESS for success. - ****************************************************************************/ -static s32 e1000_mng_host_if_write(struct e1000_hw *hw, u8 *buffer, u16 length, - u16 offset, u8 *sum) -{ - u8 *tmp; - u8 *bufptr = buffer; - u32 data = 0; - u16 remaining, i, j, prev_bytes; - - /* sum = only sum of the data and it is not checksum */ - - if (length == 0 || offset + length > E1000_HI_MAX_MNG_DATA_LENGTH) { - return -E1000_ERR_PARAM; - } - - tmp = (u8 *)&data; - prev_bytes = offset & 0x3; - offset &= 0xFFFC; - offset >>= 2; - - if (prev_bytes) { - data = E1000_READ_REG_ARRAY_DWORD(hw, HOST_IF, offset); - for (j = prev_bytes; j < sizeof(u32); j++) { - *(tmp + j) = *bufptr++; - *sum += *(tmp + j); - } - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset, data); - length -= j - prev_bytes; - offset++; - } - - remaining = length & 0x3; - length -= remaining; - - /* Calculate length in DWORDs */ - length >>= 2; - - /* The device driver writes the relevant command block into the - * ram area. */ - for (i = 0; i < length; i++) { - for (j = 0; j < sizeof(u32); j++) { - *(tmp + j) = *bufptr++; - *sum += *(tmp + j); - } - - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data); - } - if (remaining) { - for (j = 0; j < sizeof(u32); j++) { - if (j < remaining) - *(tmp + j) = *bufptr++; - else - *(tmp + j) = 0; - - *sum += *(tmp + j); - } - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, offset + i, data); - } - - return E1000_SUCCESS; -} + if ((eeprom_data != EEPROM_RESERVED_WORD) && + (eeprom_data & EEPROM_PHY_CLASS_A)) { + ret_val = + e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, + 0x000B); + if (ret_val) + return ret_val; + ret_val = + e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, + 0x8104); + if (ret_val) + return ret_val; + + hw->phy_reset_disable = false; + } + } + return E1000_SUCCESS; +} -/***************************************************************************** - * This function writes the command header after does the checksum calculation. +/** + * e1000_set_d3_lplu_state - set d3 link power state + * @hw: Struct containing variables accessed by shared code + * @active: true to enable lplu false to disable lplu. + * + * This function sets the lplu state according to the active flag. When + * activating lplu this function also disables smart speed and vise versa. + * lplu will not be activated unless the device autonegotiation advertisement + * meets standards of either 10 or 10/100 or 10/100/1000 at all duplexes. * - * returns - E1000_SUCCESS for success. - ****************************************************************************/ -static s32 e1000_mng_write_cmd_header(struct e1000_hw *hw, - struct e1000_host_mng_command_header *hdr) + * returns: - E1000_ERR_PHY if fail to read/write the PHY + * E1000_SUCCESS at any other case. + */ +static s32 e1000_set_d3_lplu_state(struct e1000_hw *hw, bool active) { - u16 i; - u8 sum; - u8 *buffer; - - /* Write the whole command header structure which includes sum of - * the buffer */ - - u16 length = sizeof(struct e1000_host_mng_command_header); + s32 ret_val; + u16 phy_data; + DEBUGFUNC("e1000_set_d3_lplu_state"); + + if (hw->phy_type != e1000_phy_igp) + return E1000_SUCCESS; + + /* During driver activity LPLU should not be used or it will attain link + * from the lowest speeds starting from 10Mbps. The capability is used for + * Dx transitions and states */ + if (hw->mac_type == e1000_82541_rev_2 + || hw->mac_type == e1000_82547_rev_2) { + ret_val = + e1000_read_phy_reg(hw, IGP01E1000_GMII_FIFO, &phy_data); + if (ret_val) + return ret_val; + } - sum = hdr->checksum; - hdr->checksum = 0; + if (!active) { + if (hw->mac_type == e1000_82541_rev_2 || + hw->mac_type == e1000_82547_rev_2) { + phy_data &= ~IGP01E1000_GMII_FLEX_SPD; + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, + phy_data); + if (ret_val) + return ret_val; + } - buffer = (u8 *)hdr; - i = length; - while (i--) - sum += buffer[i]; + /* LPLU and SmartSpeed are mutually exclusive. LPLU is used during + * Dx states where the power conservation is most important. During + * driver activity we should enable SmartSpeed, so performance is + * maintained. */ + if (hw->smart_speed == e1000_smart_speed_on) { + ret_val = + e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + + phy_data |= IGP01E1000_PSCFR_SMART_SPEED; + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + } else if (hw->smart_speed == e1000_smart_speed_off) { + ret_val = + e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; + + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; + } + } else if ((hw->autoneg_advertised == AUTONEG_ADVERTISE_SPEED_DEFAULT) + || (hw->autoneg_advertised == AUTONEG_ADVERTISE_10_ALL) + || (hw->autoneg_advertised == + AUTONEG_ADVERTISE_10_100_ALL)) { + + if (hw->mac_type == e1000_82541_rev_2 || + hw->mac_type == e1000_82547_rev_2) { + phy_data |= IGP01E1000_GMII_FLEX_SPD; + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_GMII_FIFO, + phy_data); + if (ret_val) + return ret_val; + } - hdr->checksum = 0 - sum; + /* When LPLU is enabled we should disable SmartSpeed */ + ret_val = + e1000_read_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + &phy_data); + if (ret_val) + return ret_val; - length >>= 2; - /* The device driver writes the relevant command block into the ram area. */ - for (i = 0; i < length; i++) { - E1000_WRITE_REG_ARRAY_DWORD(hw, HOST_IF, i, *((u32 *)hdr + i)); - E1000_WRITE_FLUSH(); - } + phy_data &= ~IGP01E1000_PSCFR_SMART_SPEED; + ret_val = + e1000_write_phy_reg(hw, IGP01E1000_PHY_PORT_CONFIG, + phy_data); + if (ret_val) + return ret_val; - return E1000_SUCCESS; + } + return E1000_SUCCESS; } - -/***************************************************************************** - * This function indicates to ARC that a new command is pending which completes - * one write operation by the driver. +/** + * e1000_set_vco_speed + * @hw: Struct containing variables accessed by shared code * - * returns - E1000_SUCCESS for success. - ****************************************************************************/ -static s32 e1000_mng_write_commit(struct e1000_hw *hw) + * Change VCO speed register to improve Bit Error Rate performance of SERDES. + */ +static s32 e1000_set_vco_speed(struct e1000_hw *hw) { - u32 hicr; + s32 ret_val; + u16 default_page = 0; + u16 phy_data; - hicr = er32(HICR); - /* Setting this bit tells the ARC that a new command is pending. */ - ew32(HICR, hicr | E1000_HICR_C); + DEBUGFUNC("e1000_set_vco_speed"); - return E1000_SUCCESS; -} + switch (hw->mac_type) { + case e1000_82545_rev_3: + case e1000_82546_rev_3: + break; + default: + return E1000_SUCCESS; + } + /* Set PHY register 30, page 5, bit 8 to 0 */ -/***************************************************************************** - * This function checks the mode of the firmware. - * - * returns - true when the mode is IAMT or false. - ****************************************************************************/ -bool e1000_check_mng_mode(struct e1000_hw *hw) -{ - u32 fwsm; - - fwsm = er32(FWSM); + ret_val = + e1000_read_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, &default_page); + if (ret_val) + return ret_val; - if (hw->mac_type == e1000_ich8lan) { - if ((fwsm & E1000_FWSM_MODE_MASK) == - (E1000_MNG_ICH_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) - return true; - } else if ((fwsm & E1000_FWSM_MODE_MASK) == - (E1000_MNG_IAMT_MODE << E1000_FWSM_MODE_SHIFT)) - return true; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0005); + if (ret_val) + return ret_val; - return false; -} + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); + if (ret_val) + return ret_val; + phy_data &= ~M88E1000_PHY_VCO_REG_BIT8; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); + if (ret_val) + return ret_val; -/***************************************************************************** - * This function writes the dhcp info . - ****************************************************************************/ -s32 e1000_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, u16 length) -{ - s32 ret_val; - struct e1000_host_mng_command_header hdr; - - hdr.command_id = E1000_MNG_DHCP_TX_PAYLOAD_CMD; - hdr.command_length = length; - hdr.reserved1 = 0; - hdr.reserved2 = 0; - hdr.checksum = 0; - - ret_val = e1000_mng_enable_host_if(hw); - if (ret_val == E1000_SUCCESS) { - ret_val = e1000_mng_host_if_write(hw, buffer, length, sizeof(hdr), - &(hdr.checksum)); - if (ret_val == E1000_SUCCESS) { - ret_val = e1000_mng_write_cmd_header(hw, &hdr); - if (ret_val == E1000_SUCCESS) - ret_val = e1000_mng_write_commit(hw); - } - } - return ret_val; -} + /* Set PHY register 30, page 4, bit 11 to 1 */ + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0004); + if (ret_val) + return ret_val; -/***************************************************************************** - * This function calculates the checksum. - * - * returns - checksum of buffer contents. - ****************************************************************************/ -static u8 e1000_calculate_mng_checksum(char *buffer, u32 length) -{ - u8 sum = 0; - u32 i; + ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, &phy_data); + if (ret_val) + return ret_val; - if (!buffer) - return 0; + phy_data |= M88E1000_PHY_VCO_REG_BIT11; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, phy_data); + if (ret_val) + return ret_val; - for (i=0; i < length; i++) - sum += buffer[i]; + ret_val = + e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, default_page); + if (ret_val) + return ret_val; - return (u8)(0 - sum); + return E1000_SUCCESS; } -/***************************************************************************** - * This function checks whether tx pkt filtering needs to be enabled or not. - * - * returns - true for packet filtering or false. - ****************************************************************************/ -bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw) -{ - /* called in init as well as watchdog timer functions */ - - s32 ret_val, checksum; - bool tx_filter = false; - struct e1000_host_mng_dhcp_cookie *hdr = &(hw->mng_cookie); - u8 *buffer = (u8 *) &(hw->mng_cookie); - - if (e1000_check_mng_mode(hw)) { - ret_val = e1000_mng_enable_host_if(hw); - if (ret_val == E1000_SUCCESS) { - ret_val = e1000_host_if_read_cookie(hw, buffer); - if (ret_val == E1000_SUCCESS) { - checksum = hdr->checksum; - hdr->checksum = 0; - if ((hdr->signature == E1000_IAMT_SIGNATURE) && - checksum == e1000_calculate_mng_checksum((char *)buffer, - E1000_MNG_DHCP_COOKIE_LENGTH)) { - if (hdr->status & - E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT) - tx_filter = true; - } else - tx_filter = true; - } else - tx_filter = true; - } - } - - hw->tx_pkt_filtering = tx_filter; - return tx_filter; -} -/****************************************************************************** - * Verifies the hardware needs to allow ARPs to be processed by the host - * - * hw - Struct containing variables accessed by shared code +/** + * e1000_enable_mng_pass_thru - check for bmc pass through + * @hw: Struct containing variables accessed by shared code * + * Verifies the hardware needs to allow ARPs to be processed by the host * returns: - true/false - * - *****************************************************************************/ + */ u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw) { - u32 manc; - u32 fwsm, factps; - - if (hw->asf_firmware_present) { - manc = er32(MANC); - - if (!(manc & E1000_MANC_RCV_TCO_EN) || - !(manc & E1000_MANC_EN_MAC_ADDR_FILTER)) - return false; - if (e1000_arc_subsystem_valid(hw)) { - fwsm = er32(FWSM); - factps = er32(FACTPS); - - if ((((fwsm & E1000_FWSM_MODE_MASK) >> E1000_FWSM_MODE_SHIFT) == - e1000_mng_mode_pt) && !(factps & E1000_FACTPS_MNGCG)) - return true; - } else - if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN)) - return true; - } - return false; -} + u32 manc; -static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw) -{ - s32 ret_val; - u16 mii_status_reg; - u16 i; - - /* Polarity reversal workaround for forced 10F/10H links. */ - - /* Disable the transmitter on the PHY */ - - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); - if (ret_val) - return ret_val; - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF); - if (ret_val) - return ret_val; - - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); - if (ret_val) - return ret_val; - - /* This loop will early-out if the NO link condition has been met. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Link Status bit - * to be clear. - */ - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) break; - mdelay(100); - } - - /* Recommended delay time after link has been lost */ - mdelay(1000); - - /* Now we will re-enable th transmitter on the PHY */ - - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); - if (ret_val) - return ret_val; - mdelay(50); - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0); - if (ret_val) - return ret_val; - mdelay(50); - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00); - if (ret_val) - return ret_val; - mdelay(50); - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000); - if (ret_val) - return ret_val; - - ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); - if (ret_val) - return ret_val; - - /* This loop will early-out if the link condition has been met. */ - for (i = PHY_FORCE_TIME; i > 0; i--) { - /* Read the MII Status Register and wait for Link Status bit - * to be set. - */ - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); - if (ret_val) - return ret_val; - - if (mii_status_reg & MII_SR_LINK_STATUS) break; - mdelay(100); - } - return E1000_SUCCESS; + if (hw->asf_firmware_present) { + manc = er32(MANC); + + if (!(manc & E1000_MANC_RCV_TCO_EN) || + !(manc & E1000_MANC_EN_MAC_ADDR_FILTER)) + return false; + if ((manc & E1000_MANC_SMBUS_EN) && !(manc & E1000_MANC_ASF_EN)) + return true; + } + return false; } -/*************************************************************************** - * - * Disables PCI-Express master access. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - none. - * - ***************************************************************************/ -static void e1000_set_pci_express_master_disable(struct e1000_hw *hw) +static s32 e1000_polarity_reversal_workaround(struct e1000_hw *hw) { - u32 ctrl; + s32 ret_val; + u16 mii_status_reg; + u16 i; - DEBUGFUNC("e1000_set_pci_express_master_disable"); + /* Polarity reversal workaround for forced 10F/10H links. */ - if (hw->bus_type != e1000_bus_type_pci_express) - return; + /* Disable the transmitter on the PHY */ - ctrl = er32(CTRL); - ctrl |= E1000_CTRL_GIO_MASTER_DISABLE; - ew32(CTRL, ctrl); -} + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); + if (ret_val) + return ret_val; + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFFF); + if (ret_val) + return ret_val; -/******************************************************************************* - * - * Disables PCI-Express master access and verifies there are no pending requests - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_MASTER_REQUESTS_PENDING if master disable bit hasn't - * caused the master requests to be disabled. - * E1000_SUCCESS master requests disabled. - * - ******************************************************************************/ -s32 e1000_disable_pciex_master(struct e1000_hw *hw) -{ - s32 timeout = MASTER_DISABLE_TIMEOUT; /* 80ms */ + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); + if (ret_val) + return ret_val; - DEBUGFUNC("e1000_disable_pciex_master"); + /* This loop will early-out if the NO link condition has been met. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Link Status bit + * to be clear. + */ - if (hw->bus_type != e1000_bus_type_pci_express) - return E1000_SUCCESS; + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; - e1000_set_pci_express_master_disable(hw); + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; - while (timeout) { - if (!(er32(STATUS) & E1000_STATUS_GIO_MASTER_ENABLE)) - break; - else - udelay(100); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Master requests are pending.\n"); - return -E1000_ERR_MASTER_REQUESTS_PENDING; - } + if ((mii_status_reg & ~MII_SR_LINK_STATUS) == 0) + break; + mdelay(100); + } - return E1000_SUCCESS; + /* Recommended delay time after link has been lost */ + mdelay(1000); + + /* Now we will re-enable th transmitter on the PHY */ + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0019); + if (ret_val) + return ret_val; + mdelay(50); + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFFF0); + if (ret_val) + return ret_val; + mdelay(50); + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0xFF00); + if (ret_val) + return ret_val; + mdelay(50); + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_GEN_CONTROL, 0x0000); + if (ret_val) + return ret_val; + + ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_PAGE_SELECT, 0x0000); + if (ret_val) + return ret_val; + + /* This loop will early-out if the link condition has been met. */ + for (i = PHY_FORCE_TIME; i > 0; i--) { + /* Read the MII Status Register and wait for Link Status bit + * to be set. + */ + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + ret_val = e1000_read_phy_reg(hw, PHY_STATUS, &mii_status_reg); + if (ret_val) + return ret_val; + + if (mii_status_reg & MII_SR_LINK_STATUS) + break; + mdelay(100); + } + return E1000_SUCCESS; } -/******************************************************************************* +/** + * e1000_get_auto_rd_done + * @hw: Struct containing variables accessed by shared code * * Check for EEPROM Auto Read bit done. - * - * hw: Struct containing variables accessed by shared code - * * returns: - E1000_ERR_RESET if fail to reset MAC * E1000_SUCCESS at any other case. - * - ******************************************************************************/ + */ static s32 e1000_get_auto_rd_done(struct e1000_hw *hw) { - s32 timeout = AUTO_READ_DONE_TIMEOUT; - - DEBUGFUNC("e1000_get_auto_rd_done"); - - switch (hw->mac_type) { - default: - msleep(5); - break; - case e1000_82571: - case e1000_82572: - case e1000_82573: - case e1000_80003es2lan: - case e1000_ich8lan: - while (timeout) { - if (er32(EECD) & E1000_EECD_AUTO_RD) - break; - else msleep(1); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Auto read by HW from EEPROM has not completed.\n"); - return -E1000_ERR_RESET; - } - break; - } - - /* PHY configuration from NVM just starts after EECD_AUTO_RD sets to high. - * Need to wait for PHY configuration completion before accessing NVM - * and PHY. */ - if (hw->mac_type == e1000_82573) - msleep(25); - - return E1000_SUCCESS; + DEBUGFUNC("e1000_get_auto_rd_done"); + msleep(5); + return E1000_SUCCESS; } -/*************************************************************************** - * Checks if the PHY configuration is done - * - * hw: Struct containing variables accessed by shared code +/** + * e1000_get_phy_cfg_done + * @hw: Struct containing variables accessed by shared code * + * Checks if the PHY configuration is done * returns: - E1000_ERR_RESET if fail to reset MAC * E1000_SUCCESS at any other case. - * - ***************************************************************************/ + */ static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw) { - s32 timeout = PHY_CFG_TIMEOUT; - u32 cfg_mask = E1000_EEPROM_CFG_DONE; - - DEBUGFUNC("e1000_get_phy_cfg_done"); - - switch (hw->mac_type) { - default: - mdelay(10); - break; - case e1000_80003es2lan: - /* Separate *_CFG_DONE_* bit for each port */ - if (er32(STATUS) & E1000_STATUS_FUNC_1) - cfg_mask = E1000_EEPROM_CFG_DONE_PORT_1; - /* Fall Through */ - case e1000_82571: - case e1000_82572: - while (timeout) { - if (er32(EEMNGCTL) & cfg_mask) - break; - else - msleep(1); - timeout--; - } - if (!timeout) { - DEBUGOUT("MNG configuration cycle has not completed.\n"); - return -E1000_ERR_RESET; - } - break; - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Using the combination of SMBI and SWESMBI semaphore bits when resetting - * adapter or Eeprom access. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_EEPROM if fail to access EEPROM. - * E1000_SUCCESS at any other case. - * - ***************************************************************************/ -static s32 e1000_get_hw_eeprom_semaphore(struct e1000_hw *hw) -{ - s32 timeout; - u32 swsm; - - DEBUGFUNC("e1000_get_hw_eeprom_semaphore"); - - if (!hw->eeprom_semaphore_present) - return E1000_SUCCESS; - - if (hw->mac_type == e1000_80003es2lan) { - /* Get the SW semaphore. */ - if (e1000_get_software_semaphore(hw) != E1000_SUCCESS) - return -E1000_ERR_EEPROM; - } - - /* Get the FW semaphore. */ - timeout = hw->eeprom.word_size + 1; - while (timeout) { - swsm = er32(SWSM); - swsm |= E1000_SWSM_SWESMBI; - ew32(SWSM, swsm); - /* if we managed to set the bit we got the semaphore. */ - swsm = er32(SWSM); - if (swsm & E1000_SWSM_SWESMBI) - break; - - udelay(50); - timeout--; - } - - if (!timeout) { - /* Release semaphores */ - e1000_put_hw_eeprom_semaphore(hw); - DEBUGOUT("Driver can't access the Eeprom - SWESMBI bit is set.\n"); - return -E1000_ERR_EEPROM; - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * This function clears HW semaphore bits. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - None. - * - ***************************************************************************/ -static void e1000_put_hw_eeprom_semaphore(struct e1000_hw *hw) -{ - u32 swsm; - - DEBUGFUNC("e1000_put_hw_eeprom_semaphore"); - - if (!hw->eeprom_semaphore_present) - return; - - swsm = er32(SWSM); - if (hw->mac_type == e1000_80003es2lan) { - /* Release both semaphores. */ - swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI); - } else - swsm &= ~(E1000_SWSM_SWESMBI); - ew32(SWSM, swsm); -} - -/*************************************************************************** - * - * Obtaining software semaphore bit (SMBI) before resetting PHY. - * - * hw: Struct containing variables accessed by shared code - * - * returns: - E1000_ERR_RESET if fail to obtain semaphore. - * E1000_SUCCESS at any other case. - * - ***************************************************************************/ -static s32 e1000_get_software_semaphore(struct e1000_hw *hw) -{ - s32 timeout = hw->eeprom.word_size + 1; - u32 swsm; - - DEBUGFUNC("e1000_get_software_semaphore"); - - if (hw->mac_type != e1000_80003es2lan) { - return E1000_SUCCESS; - } - - while (timeout) { - swsm = er32(SWSM); - /* If SMBI bit cleared, it is now set and we hold the semaphore */ - if (!(swsm & E1000_SWSM_SMBI)) - break; - mdelay(1); - timeout--; - } - - if (!timeout) { - DEBUGOUT("Driver can't access device - SMBI bit is set.\n"); - return -E1000_ERR_RESET; - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Release semaphore bit (SMBI). - * - * hw: Struct containing variables accessed by shared code - * - ***************************************************************************/ -static void e1000_release_software_semaphore(struct e1000_hw *hw) -{ - u32 swsm; - - DEBUGFUNC("e1000_release_software_semaphore"); - - if (hw->mac_type != e1000_80003es2lan) { - return; - } - - swsm = er32(SWSM); - /* Release the SW semaphores.*/ - swsm &= ~E1000_SWSM_SMBI; - ew32(SWSM, swsm); -} - -/****************************************************************************** - * Checks if PHY reset is blocked due to SOL/IDER session, for example. - * Returning E1000_BLK_PHY_RESET isn't necessarily an error. But it's up to - * the caller to figure out how to deal with it. - * - * hw - Struct containing variables accessed by shared code - * - * returns: - E1000_BLK_PHY_RESET - * E1000_SUCCESS - * - *****************************************************************************/ -s32 e1000_check_phy_reset_block(struct e1000_hw *hw) -{ - u32 manc = 0; - u32 fwsm = 0; - - if (hw->mac_type == e1000_ich8lan) { - fwsm = er32(FWSM); - return (fwsm & E1000_FWSM_RSPCIPHY) ? E1000_SUCCESS - : E1000_BLK_PHY_RESET; - } - - if (hw->mac_type > e1000_82547_rev_2) - manc = er32(MANC); - return (manc & E1000_MANC_BLK_PHY_RST_ON_IDE) ? - E1000_BLK_PHY_RESET : E1000_SUCCESS; -} - -static u8 e1000_arc_subsystem_valid(struct e1000_hw *hw) -{ - u32 fwsm; - - /* On 8257x silicon, registers in the range of 0x8800 - 0x8FFC - * may not be provided a DMA clock when no manageability features are - * enabled. We do not want to perform any reads/writes to these registers - * if this is the case. We read FWSM to determine the manageability mode. - */ - switch (hw->mac_type) { - case e1000_82571: - case e1000_82572: - case e1000_82573: - case e1000_80003es2lan: - fwsm = er32(FWSM); - if ((fwsm & E1000_FWSM_MODE_MASK) != 0) - return true; - break; - case e1000_ich8lan: - return true; - default: - break; - } - return false; -} - - -/****************************************************************************** - * Configure PCI-Ex no-snoop - * - * hw - Struct containing variables accessed by shared code. - * no_snoop - Bitmap of no-snoop events. - * - * returns: E1000_SUCCESS - * - *****************************************************************************/ -static s32 e1000_set_pci_ex_no_snoop(struct e1000_hw *hw, u32 no_snoop) -{ - u32 gcr_reg = 0; - - DEBUGFUNC("e1000_set_pci_ex_no_snoop"); - - if (hw->bus_type == e1000_bus_type_unknown) - e1000_get_bus_info(hw); - - if (hw->bus_type != e1000_bus_type_pci_express) - return E1000_SUCCESS; - - if (no_snoop) { - gcr_reg = er32(GCR); - gcr_reg &= ~(PCI_EX_NO_SNOOP_ALL); - gcr_reg |= no_snoop; - ew32(GCR, gcr_reg); - } - if (hw->mac_type == e1000_ich8lan) { - u32 ctrl_ext; - - ew32(GCR, PCI_EX_82566_SNOOP_ALL); - - ctrl_ext = er32(CTRL_EXT); - ctrl_ext |= E1000_CTRL_EXT_RO_DIS; - ew32(CTRL_EXT, ctrl_ext); - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Get software semaphore FLAG bit (SWFLAG). - * SWFLAG is used to synchronize the access to all shared resource between - * SW, FW and HW. - * - * hw: Struct containing variables accessed by shared code - * - ***************************************************************************/ -static s32 e1000_get_software_flag(struct e1000_hw *hw) -{ - s32 timeout = PHY_CFG_TIMEOUT; - u32 extcnf_ctrl; - - DEBUGFUNC("e1000_get_software_flag"); - - if (hw->mac_type == e1000_ich8lan) { - while (timeout) { - extcnf_ctrl = er32(EXTCNF_CTRL); - extcnf_ctrl |= E1000_EXTCNF_CTRL_SWFLAG; - ew32(EXTCNF_CTRL, extcnf_ctrl); - - extcnf_ctrl = er32(EXTCNF_CTRL); - if (extcnf_ctrl & E1000_EXTCNF_CTRL_SWFLAG) - break; - mdelay(1); - timeout--; - } - - if (!timeout) { - DEBUGOUT("FW or HW locks the resource too long.\n"); - return -E1000_ERR_CONFIG; - } - } - - return E1000_SUCCESS; -} - -/*************************************************************************** - * - * Release software semaphore FLAG bit (SWFLAG). - * SWFLAG is used to synchronize the access to all shared resource between - * SW, FW and HW. - * - * hw: Struct containing variables accessed by shared code - * - ***************************************************************************/ -static void e1000_release_software_flag(struct e1000_hw *hw) -{ - u32 extcnf_ctrl; - - DEBUGFUNC("e1000_release_software_flag"); - - if (hw->mac_type == e1000_ich8lan) { - extcnf_ctrl= er32(EXTCNF_CTRL); - extcnf_ctrl &= ~E1000_EXTCNF_CTRL_SWFLAG; - ew32(EXTCNF_CTRL, extcnf_ctrl); - } - - return; -} - -/****************************************************************************** - * Reads a 16 bit word or words from the EEPROM using the ICH8's flash access - * register. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to read - * data - word read from the EEPROM - * words - number of words to read - *****************************************************************************/ -static s32 e1000_read_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data) -{ - s32 error = E1000_SUCCESS; - u32 flash_bank = 0; - u32 act_offset = 0; - u32 bank_offset = 0; - u16 word = 0; - u16 i = 0; - - /* We need to know which is the valid flash bank. In the event - * that we didn't allocate eeprom_shadow_ram, we may not be - * managing flash_bank. So it cannot be trusted and needs - * to be updated with each read. - */ - /* Value of bit 22 corresponds to the flash bank we're on. */ - flash_bank = (er32(EECD) & E1000_EECD_SEC1VAL) ? 1 : 0; - - /* Adjust offset appropriately if we're on bank 1 - adjust for word size */ - bank_offset = flash_bank * (hw->flash_bank_size * 2); - - error = e1000_get_software_flag(hw); - if (error != E1000_SUCCESS) - return error; - - for (i = 0; i < words; i++) { - if (hw->eeprom_shadow_ram != NULL && - hw->eeprom_shadow_ram[offset+i].modified) { - data[i] = hw->eeprom_shadow_ram[offset+i].eeprom_word; - } else { - /* The NVM part needs a byte offset, hence * 2 */ - act_offset = bank_offset + ((offset + i) * 2); - error = e1000_read_ich8_word(hw, act_offset, &word); - if (error != E1000_SUCCESS) - break; - data[i] = word; - } - } - - e1000_release_software_flag(hw); - - return error; -} - -/****************************************************************************** - * Writes a 16 bit word or words to the EEPROM using the ICH8's flash access - * register. Actually, writes are written to the shadow ram cache in the hw - * structure hw->e1000_shadow_ram. e1000_commit_shadow_ram flushes this to - * the NVM, which occurs when the NVM checksum is updated. - * - * hw - Struct containing variables accessed by shared code - * offset - offset of word in the EEPROM to write - * words - number of words to write - * data - words to write to the EEPROM - *****************************************************************************/ -static s32 e1000_write_eeprom_ich8(struct e1000_hw *hw, u16 offset, u16 words, - u16 *data) -{ - u32 i = 0; - s32 error = E1000_SUCCESS; - - error = e1000_get_software_flag(hw); - if (error != E1000_SUCCESS) - return error; - - /* A driver can write to the NVM only if it has eeprom_shadow_ram - * allocated. Subsequent reads to the modified words are read from - * this cached structure as well. Writes will only go into this - * cached structure unless it's followed by a call to - * e1000_update_eeprom_checksum() where it will commit the changes - * and clear the "modified" field. - */ - if (hw->eeprom_shadow_ram != NULL) { - for (i = 0; i < words; i++) { - if ((offset + i) < E1000_SHADOW_RAM_WORDS) { - hw->eeprom_shadow_ram[offset+i].modified = true; - hw->eeprom_shadow_ram[offset+i].eeprom_word = data[i]; - } else { - error = -E1000_ERR_EEPROM; - break; - } - } - } else { - /* Drivers have the option to not allocate eeprom_shadow_ram as long - * as they don't perform any NVM writes. An attempt in doing so - * will result in this error. - */ - error = -E1000_ERR_EEPROM; - } - - e1000_release_software_flag(hw); - - return error; -} - -/****************************************************************************** - * This function does initial flash setup so that a new read/write/erase cycle - * can be started. - * - * hw - The pointer to the hw structure - ****************************************************************************/ -static s32 e1000_ich8_cycle_init(struct e1000_hw *hw) -{ - union ich8_hws_flash_status hsfsts; - s32 error = E1000_ERR_EEPROM; - s32 i = 0; - - DEBUGFUNC("e1000_ich8_cycle_init"); - - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - - /* May be check the Flash Des Valid bit in Hw status */ - if (hsfsts.hsf_status.fldesvalid == 0) { - DEBUGOUT("Flash descriptor invalid. SW Sequencing must be used."); - return error; - } - - /* Clear FCERR in Hw status by writing 1 */ - /* Clear DAEL in Hw status by writing a 1 */ - hsfsts.hsf_status.flcerr = 1; - hsfsts.hsf_status.dael = 1; - - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); - - /* Either we should have a hardware SPI cycle in progress bit to check - * against, in order to start a new cycle or FDONE bit should be changed - * in the hardware so that it is 1 after harware reset, which can then be - * used as an indication whether a cycle is in progress or has been - * completed .. we should also have some software semaphore mechanism to - * guard FDONE or the cycle in progress bit so that two threads access to - * those bits can be sequentiallized or a way so that 2 threads dont - * start the cycle at the same time */ - - if (hsfsts.hsf_status.flcinprog == 0) { - /* There is no cycle running at present, so we can start a cycle */ - /* Begin by setting Flash Cycle Done. */ - hsfsts.hsf_status.flcdone = 1; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); - error = E1000_SUCCESS; - } else { - /* otherwise poll for sometime so the current cycle has a chance - * to end before giving up. */ - for (i = 0; i < ICH_FLASH_COMMAND_TIMEOUT; i++) { - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcinprog == 0) { - error = E1000_SUCCESS; - break; - } - udelay(1); - } - if (error == E1000_SUCCESS) { - /* Successful in waiting for previous cycle to timeout, - * now set the Flash Cycle Done. */ - hsfsts.hsf_status.flcdone = 1; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS, hsfsts.regval); - } else { - DEBUGOUT("Flash controller busy, cannot get access"); - } - } - return error; -} - -/****************************************************************************** - * This function starts a flash cycle and waits for its completion - * - * hw - The pointer to the hw structure - ****************************************************************************/ -static s32 e1000_ich8_flash_cycle(struct e1000_hw *hw, u32 timeout) -{ - union ich8_hws_flash_ctrl hsflctl; - union ich8_hws_flash_status hsfsts; - s32 error = E1000_ERR_EEPROM; - u32 i = 0; - - /* Start a cycle by writing 1 in Flash Cycle Go in Hw Flash Control */ - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - hsflctl.hsf_ctrl.flcgo = 1; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* wait till FDONE bit is set to 1 */ - do { - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcdone == 1) - break; - udelay(1); - i++; - } while (i < timeout); - if (hsfsts.hsf_status.flcdone == 1 && hsfsts.hsf_status.flcerr == 0) { - error = E1000_SUCCESS; - } - return error; -} - -/****************************************************************************** - * Reads a byte or word from the NVM using the ICH8 flash access registers. - * - * hw - The pointer to the hw structure - * index - The index of the byte or word to read. - * size - Size of data to read, 1=byte 2=word - * data - Pointer to the word to store the value read. - *****************************************************************************/ -static s32 e1000_read_ich8_data(struct e1000_hw *hw, u32 index, u32 size, - u16 *data) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - u32 flash_linear_address; - u32 flash_data = 0; - s32 error = -E1000_ERR_EEPROM; - s32 count = 0; - - DEBUGFUNC("e1000_read_ich8_data"); - - if (size < 1 || size > 2 || data == NULL || - index > ICH_FLASH_LINEAR_ADDR_MASK) - return error; - - flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) + - hw->flash_base_addr; - - do { - udelay(1); - /* Steps */ - error = e1000_ich8_cycle_init(hw); - if (error != E1000_SUCCESS) - break; - - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ - hsflctl.hsf_ctrl.fldbcount = size - 1; - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_READ; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* Write the last 24 bits of index into Flash Linear address field in - * Flash Address */ - /* TODO: TBD maybe check the index against the size of flash */ - - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); - - error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT); - - /* Check if FCERR is set to 1, if set to 1, clear it and try the whole - * sequence a few more times, else read in (shift in) the Flash Data0, - * the order is least significant byte first msb to lsb */ - if (error == E1000_SUCCESS) { - flash_data = E1000_READ_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0); - if (size == 1) { - *data = (u8)(flash_data & 0x000000FF); - } else if (size == 2) { - *data = (u16)(flash_data & 0x0000FFFF); - } - break; - } else { - /* If we've gotten here, then things are probably completely hosed, - * but if the error condition is detected, it won't hurt to give - * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times. - */ - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) { - /* Repeat for some time before giving up. */ - continue; - } else if (hsfsts.hsf_status.flcdone == 0) { - DEBUGOUT("Timeout error - flash cycle did not complete."); - break; - } - } - } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); - - return error; -} - -/****************************************************************************** - * Writes One /two bytes to the NVM using the ICH8 flash access registers. - * - * hw - The pointer to the hw structure - * index - The index of the byte/word to read. - * size - Size of data to read, 1=byte 2=word - * data - The byte(s) to write to the NVM. - *****************************************************************************/ -static s32 e1000_write_ich8_data(struct e1000_hw *hw, u32 index, u32 size, - u16 data) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - u32 flash_linear_address; - u32 flash_data = 0; - s32 error = -E1000_ERR_EEPROM; - s32 count = 0; - - DEBUGFUNC("e1000_write_ich8_data"); - - if (size < 1 || size > 2 || data > size * 0xff || - index > ICH_FLASH_LINEAR_ADDR_MASK) - return error; - - flash_linear_address = (ICH_FLASH_LINEAR_ADDR_MASK & index) + - hw->flash_base_addr; - - do { - udelay(1); - /* Steps */ - error = e1000_ich8_cycle_init(hw); - if (error != E1000_SUCCESS) - break; - - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - /* 0b/1b corresponds to 1 or 2 byte size, respectively. */ - hsflctl.hsf_ctrl.fldbcount = size -1; - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_WRITE; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* Write the last 24 bits of index into Flash Linear address field in - * Flash Address */ - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); - - if (size == 1) - flash_data = (u32)data & 0x00FF; - else - flash_data = (u32)data; - - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FDATA0, flash_data); - - /* check if FCERR is set to 1 , if set to 1, clear it and try the whole - * sequence a few more times else done */ - error = e1000_ich8_flash_cycle(hw, ICH_FLASH_COMMAND_TIMEOUT); - if (error == E1000_SUCCESS) { - break; - } else { - /* If we're here, then things are most likely completely hosed, - * but if the error condition is detected, it won't hurt to give - * it another try...ICH_FLASH_CYCLE_REPEAT_COUNT times. - */ - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) { - /* Repeat for some time before giving up. */ - continue; - } else if (hsfsts.hsf_status.flcdone == 0) { - DEBUGOUT("Timeout error - flash cycle did not complete."); - break; - } - } - } while (count++ < ICH_FLASH_CYCLE_REPEAT_COUNT); - - return error; -} - -/****************************************************************************** - * Reads a single byte from the NVM using the ICH8 flash access registers. - * - * hw - pointer to e1000_hw structure - * index - The index of the byte to read. - * data - Pointer to a byte to store the value read. - *****************************************************************************/ -static s32 e1000_read_ich8_byte(struct e1000_hw *hw, u32 index, u8 *data) -{ - s32 status = E1000_SUCCESS; - u16 word = 0; - - status = e1000_read_ich8_data(hw, index, 1, &word); - if (status == E1000_SUCCESS) { - *data = (u8)word; - } - - return status; -} - -/****************************************************************************** - * Writes a single byte to the NVM using the ICH8 flash access registers. - * Performs verification by reading back the value and then going through - * a retry algorithm before giving up. - * - * hw - pointer to e1000_hw structure - * index - The index of the byte to write. - * byte - The byte to write to the NVM. - *****************************************************************************/ -static s32 e1000_verify_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 byte) -{ - s32 error = E1000_SUCCESS; - s32 program_retries = 0; - - DEBUGOUT2("Byte := %2.2X Offset := %d\n", byte, index); - - error = e1000_write_ich8_byte(hw, index, byte); - - if (error != E1000_SUCCESS) { - for (program_retries = 0; program_retries < 100; program_retries++) { - DEBUGOUT2("Retrying \t Byte := %2.2X Offset := %d\n", byte, index); - error = e1000_write_ich8_byte(hw, index, byte); - udelay(100); - if (error == E1000_SUCCESS) - break; - } - } - - if (program_retries == 100) - error = E1000_ERR_EEPROM; - - return error; -} - -/****************************************************************************** - * Writes a single byte to the NVM using the ICH8 flash access registers. - * - * hw - pointer to e1000_hw structure - * index - The index of the byte to read. - * data - The byte to write to the NVM. - *****************************************************************************/ -static s32 e1000_write_ich8_byte(struct e1000_hw *hw, u32 index, u8 data) -{ - s32 status = E1000_SUCCESS; - u16 word = (u16)data; - - status = e1000_write_ich8_data(hw, index, 1, word); - - return status; -} - -/****************************************************************************** - * Reads a word from the NVM using the ICH8 flash access registers. - * - * hw - pointer to e1000_hw structure - * index - The starting byte index of the word to read. - * data - Pointer to a word to store the value read. - *****************************************************************************/ -static s32 e1000_read_ich8_word(struct e1000_hw *hw, u32 index, u16 *data) -{ - s32 status = E1000_SUCCESS; - status = e1000_read_ich8_data(hw, index, 2, data); - return status; -} - -/****************************************************************************** - * Erases the bank specified. Each bank may be a 4, 8 or 64k block. Banks are 0 - * based. - * - * hw - pointer to e1000_hw structure - * bank - 0 for first bank, 1 for second bank - * - * Note that this function may actually erase as much as 8 or 64 KBytes. The - * amount of NVM used in each bank is a *minimum* of 4 KBytes, but in fact the - * bank size may be 4, 8 or 64 KBytes - *****************************************************************************/ -static s32 e1000_erase_ich8_4k_segment(struct e1000_hw *hw, u32 bank) -{ - union ich8_hws_flash_status hsfsts; - union ich8_hws_flash_ctrl hsflctl; - u32 flash_linear_address; - s32 count = 0; - s32 error = E1000_ERR_EEPROM; - s32 iteration; - s32 sub_sector_size = 0; - s32 bank_size; - s32 j = 0; - s32 error_flag = 0; - - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - - /* Determine HW Sector size: Read BERASE bits of Hw flash Status register */ - /* 00: The Hw sector is 256 bytes, hence we need to erase 16 - * consecutive sectors. The start index for the nth Hw sector can be - * calculated as bank * 4096 + n * 256 - * 01: The Hw sector is 4K bytes, hence we need to erase 1 sector. - * The start index for the nth Hw sector can be calculated - * as bank * 4096 - * 10: The HW sector is 8K bytes - * 11: The Hw sector size is 64K bytes */ - if (hsfsts.hsf_status.berasesz == 0x0) { - /* Hw sector size 256 */ - sub_sector_size = ICH_FLASH_SEG_SIZE_256; - bank_size = ICH_FLASH_SECTOR_SIZE; - iteration = ICH_FLASH_SECTOR_SIZE / ICH_FLASH_SEG_SIZE_256; - } else if (hsfsts.hsf_status.berasesz == 0x1) { - bank_size = ICH_FLASH_SEG_SIZE_4K; - iteration = 1; - } else if (hsfsts.hsf_status.berasesz == 0x3) { - bank_size = ICH_FLASH_SEG_SIZE_64K; - iteration = 1; - } else { - return error; - } - - for (j = 0; j < iteration ; j++) { - do { - count++; - /* Steps */ - error = e1000_ich8_cycle_init(hw); - if (error != E1000_SUCCESS) { - error_flag = 1; - break; - } - - /* Write a value 11 (block Erase) in Flash Cycle field in Hw flash - * Control */ - hsflctl.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL); - hsflctl.hsf_ctrl.flcycle = ICH_CYCLE_ERASE; - E1000_WRITE_ICH_FLASH_REG16(hw, ICH_FLASH_HSFCTL, hsflctl.regval); - - /* Write the last 24 bits of an index within the block into Flash - * Linear address field in Flash Address. This probably needs to - * be calculated here based off the on-chip erase sector size and - * the software bank size (4, 8 or 64 KBytes) */ - flash_linear_address = bank * bank_size + j * sub_sector_size; - flash_linear_address += hw->flash_base_addr; - flash_linear_address &= ICH_FLASH_LINEAR_ADDR_MASK; - - E1000_WRITE_ICH_FLASH_REG(hw, ICH_FLASH_FADDR, flash_linear_address); - - error = e1000_ich8_flash_cycle(hw, ICH_FLASH_ERASE_TIMEOUT); - /* Check if FCERR is set to 1. If 1, clear it and try the whole - * sequence a few more times else Done */ - if (error == E1000_SUCCESS) { - break; - } else { - hsfsts.regval = E1000_READ_ICH_FLASH_REG16(hw, ICH_FLASH_HSFSTS); - if (hsfsts.hsf_status.flcerr == 1) { - /* repeat for some time before giving up */ - continue; - } else if (hsfsts.hsf_status.flcdone == 0) { - error_flag = 1; - break; - } - } - } while ((count < ICH_FLASH_CYCLE_REPEAT_COUNT) && !error_flag); - if (error_flag == 1) - break; - } - if (error_flag != 1) - error = E1000_SUCCESS; - return error; -} - -static s32 e1000_init_lcd_from_nvm_config_region(struct e1000_hw *hw, - u32 cnf_base_addr, - u32 cnf_size) -{ - u32 ret_val = E1000_SUCCESS; - u16 word_addr, reg_data, reg_addr; - u16 i; - - /* cnf_base_addr is in DWORD */ - word_addr = (u16)(cnf_base_addr << 1); - - /* cnf_size is returned in size of dwords */ - for (i = 0; i < cnf_size; i++) { - ret_val = e1000_read_eeprom(hw, (word_addr + i*2), 1, ®_data); - if (ret_val) - return ret_val; - - ret_val = e1000_read_eeprom(hw, (word_addr + i*2 + 1), 1, ®_addr); - if (ret_val) - return ret_val; - - ret_val = e1000_get_software_flag(hw); - if (ret_val != E1000_SUCCESS) - return ret_val; - - ret_val = e1000_write_phy_reg_ex(hw, (u32)reg_addr, reg_data); - - e1000_release_software_flag(hw); - } - - return ret_val; -} - - -/****************************************************************************** - * This function initializes the PHY from the NVM on ICH8 platforms. This - * is needed due to an issue where the NVM configuration is not properly - * autoloaded after power transitions. Therefore, after each PHY reset, we - * will load the configuration data out of the NVM manually. - * - * hw: Struct containing variables accessed by shared code - *****************************************************************************/ -static s32 e1000_init_lcd_from_nvm(struct e1000_hw *hw) -{ - u32 reg_data, cnf_base_addr, cnf_size, ret_val, loop; - - if (hw->phy_type != e1000_phy_igp_3) - return E1000_SUCCESS; - - /* Check if SW needs configure the PHY */ - reg_data = er32(FEXTNVM); - if (!(reg_data & FEXTNVM_SW_CONFIG)) - return E1000_SUCCESS; - - /* Wait for basic configuration completes before proceeding*/ - loop = 0; - do { - reg_data = er32(STATUS) & E1000_STATUS_LAN_INIT_DONE; - udelay(100); - loop++; - } while ((!reg_data) && (loop < 50)); - - /* Clear the Init Done bit for the next init event */ - reg_data = er32(STATUS); - reg_data &= ~E1000_STATUS_LAN_INIT_DONE; - ew32(STATUS, reg_data); - - /* Make sure HW does not configure LCD from PHY extended configuration - before SW configuration */ - reg_data = er32(EXTCNF_CTRL); - if ((reg_data & E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE) == 0x0000) { - reg_data = er32(EXTCNF_SIZE); - cnf_size = reg_data & E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH; - cnf_size >>= 16; - if (cnf_size) { - reg_data = er32(EXTCNF_CTRL); - cnf_base_addr = reg_data & E1000_EXTCNF_CTRL_EXT_CNF_POINTER; - /* cnf_base_addr is in DWORD */ - cnf_base_addr >>= 16; - - /* Configure LCD from extended configuration region. */ - ret_val = e1000_init_lcd_from_nvm_config_region(hw, cnf_base_addr, - cnf_size); - if (ret_val) - return ret_val; - } - } - - return E1000_SUCCESS; + DEBUGFUNC("e1000_get_phy_cfg_done"); + mdelay(10); + return E1000_SUCCESS; } - diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h index a8866bdbb67..9acfddb0daf 100644 --- a/drivers/net/e1000/e1000_hw.h +++ b/drivers/net/e1000/e1000_hw.h @@ -35,7 +35,6 @@ #include "e1000_osdep.h" - /* Forward declarations of structures used by the shared code */ struct e1000_hw; struct e1000_hw_stats; @@ -43,252 +42,231 @@ struct e1000_hw_stats; /* Enumerated types specific to the e1000 hardware */ /* Media Access Controlers */ typedef enum { - e1000_undefined = 0, - e1000_82542_rev2_0, - e1000_82542_rev2_1, - e1000_82543, - e1000_82544, - e1000_82540, - e1000_82545, - e1000_82545_rev_3, - e1000_82546, - e1000_82546_rev_3, - e1000_82541, - e1000_82541_rev_2, - e1000_82547, - e1000_82547_rev_2, - e1000_82571, - e1000_82572, - e1000_82573, - e1000_80003es2lan, - e1000_ich8lan, - e1000_num_macs + e1000_undefined = 0, + e1000_82542_rev2_0, + e1000_82542_rev2_1, + e1000_82543, + e1000_82544, + e1000_82540, + e1000_82545, + e1000_82545_rev_3, + e1000_82546, + e1000_82546_rev_3, + e1000_82541, + e1000_82541_rev_2, + e1000_82547, + e1000_82547_rev_2, + e1000_num_macs } e1000_mac_type; typedef enum { - e1000_eeprom_uninitialized = 0, - e1000_eeprom_spi, - e1000_eeprom_microwire, - e1000_eeprom_flash, - e1000_eeprom_ich8, - e1000_eeprom_none, /* No NVM support */ - e1000_num_eeprom_types + e1000_eeprom_uninitialized = 0, + e1000_eeprom_spi, + e1000_eeprom_microwire, + e1000_eeprom_flash, + e1000_eeprom_none, /* No NVM support */ + e1000_num_eeprom_types } e1000_eeprom_type; /* Media Types */ typedef enum { - e1000_media_type_copper = 0, - e1000_media_type_fiber = 1, - e1000_media_type_internal_serdes = 2, - e1000_num_media_types + e1000_media_type_copper = 0, + e1000_media_type_fiber = 1, + e1000_media_type_internal_serdes = 2, + e1000_num_media_types } e1000_media_type; typedef enum { - e1000_10_half = 0, - e1000_10_full = 1, - e1000_100_half = 2, - e1000_100_full = 3 + e1000_10_half = 0, + e1000_10_full = 1, + e1000_100_half = 2, + e1000_100_full = 3 } e1000_speed_duplex_type; /* Flow Control Settings */ typedef enum { - E1000_FC_NONE = 0, - E1000_FC_RX_PAUSE = 1, - E1000_FC_TX_PAUSE = 2, - E1000_FC_FULL = 3, - E1000_FC_DEFAULT = 0xFF + E1000_FC_NONE = 0, + E1000_FC_RX_PAUSE = 1, + E1000_FC_TX_PAUSE = 2, + E1000_FC_FULL = 3, + E1000_FC_DEFAULT = 0xFF } e1000_fc_type; struct e1000_shadow_ram { - u16 eeprom_word; - bool modified; + u16 eeprom_word; + bool modified; }; /* PCI bus types */ typedef enum { - e1000_bus_type_unknown = 0, - e1000_bus_type_pci, - e1000_bus_type_pcix, - e1000_bus_type_pci_express, - e1000_bus_type_reserved + e1000_bus_type_unknown = 0, + e1000_bus_type_pci, + e1000_bus_type_pcix, + e1000_bus_type_reserved } e1000_bus_type; /* PCI bus speeds */ typedef enum { - e1000_bus_speed_unknown = 0, - e1000_bus_speed_33, - e1000_bus_speed_66, - e1000_bus_speed_100, - e1000_bus_speed_120, - e1000_bus_speed_133, - e1000_bus_speed_2500, - e1000_bus_speed_reserved + e1000_bus_speed_unknown = 0, + e1000_bus_speed_33, + e1000_bus_speed_66, + e1000_bus_speed_100, + e1000_bus_speed_120, + e1000_bus_speed_133, + e1000_bus_speed_reserved } e1000_bus_speed; /* PCI bus widths */ typedef enum { - e1000_bus_width_unknown = 0, - /* These PCIe values should literally match the possible return values - * from config space */ - e1000_bus_width_pciex_1 = 1, - e1000_bus_width_pciex_2 = 2, - e1000_bus_width_pciex_4 = 4, - e1000_bus_width_32, - e1000_bus_width_64, - e1000_bus_width_reserved + e1000_bus_width_unknown = 0, + e1000_bus_width_32, + e1000_bus_width_64, + e1000_bus_width_reserved } e1000_bus_width; /* PHY status info structure and supporting enums */ typedef enum { - e1000_cable_length_50 = 0, - e1000_cable_length_50_80, - e1000_cable_length_80_110, - e1000_cable_length_110_140, - e1000_cable_length_140, - e1000_cable_length_undefined = 0xFF + e1000_cable_length_50 = 0, + e1000_cable_length_50_80, + e1000_cable_length_80_110, + e1000_cable_length_110_140, + e1000_cable_length_140, + e1000_cable_length_undefined = 0xFF } e1000_cable_length; typedef enum { - e1000_gg_cable_length_60 = 0, - e1000_gg_cable_length_60_115 = 1, - e1000_gg_cable_length_115_150 = 2, - e1000_gg_cable_length_150 = 4 + e1000_gg_cable_length_60 = 0, + e1000_gg_cable_length_60_115 = 1, + e1000_gg_cable_length_115_150 = 2, + e1000_gg_cable_length_150 = 4 } e1000_gg_cable_length; typedef enum { - e1000_igp_cable_length_10 = 10, - e1000_igp_cable_length_20 = 20, - e1000_igp_cable_length_30 = 30, - e1000_igp_cable_length_40 = 40, - e1000_igp_cable_length_50 = 50, - e1000_igp_cable_length_60 = 60, - e1000_igp_cable_length_70 = 70, - e1000_igp_cable_length_80 = 80, - e1000_igp_cable_length_90 = 90, - e1000_igp_cable_length_100 = 100, - e1000_igp_cable_length_110 = 110, - e1000_igp_cable_length_115 = 115, - e1000_igp_cable_length_120 = 120, - e1000_igp_cable_length_130 = 130, - e1000_igp_cable_length_140 = 140, - e1000_igp_cable_length_150 = 150, - e1000_igp_cable_length_160 = 160, - e1000_igp_cable_length_170 = 170, - e1000_igp_cable_length_180 = 180 + e1000_igp_cable_length_10 = 10, + e1000_igp_cable_length_20 = 20, + e1000_igp_cable_length_30 = 30, + e1000_igp_cable_length_40 = 40, + e1000_igp_cable_length_50 = 50, + e1000_igp_cable_length_60 = 60, + e1000_igp_cable_length_70 = 70, + e1000_igp_cable_length_80 = 80, + e1000_igp_cable_length_90 = 90, + e1000_igp_cable_length_100 = 100, + e1000_igp_cable_length_110 = 110, + e1000_igp_cable_length_115 = 115, + e1000_igp_cable_length_120 = 120, + e1000_igp_cable_length_130 = 130, + e1000_igp_cable_length_140 = 140, + e1000_igp_cable_length_150 = 150, + e1000_igp_cable_length_160 = 160, + e1000_igp_cable_length_170 = 170, + e1000_igp_cable_length_180 = 180 } e1000_igp_cable_length; typedef enum { - e1000_10bt_ext_dist_enable_normal = 0, - e1000_10bt_ext_dist_enable_lower, - e1000_10bt_ext_dist_enable_undefined = 0xFF + e1000_10bt_ext_dist_enable_normal = 0, + e1000_10bt_ext_dist_enable_lower, + e1000_10bt_ext_dist_enable_undefined = 0xFF } e1000_10bt_ext_dist_enable; typedef enum { - e1000_rev_polarity_normal = 0, - e1000_rev_polarity_reversed, - e1000_rev_polarity_undefined = 0xFF + e1000_rev_polarity_normal = 0, + e1000_rev_polarity_reversed, + e1000_rev_polarity_undefined = 0xFF } e1000_rev_polarity; typedef enum { - e1000_downshift_normal = 0, - e1000_downshift_activated, - e1000_downshift_undefined = 0xFF + e1000_downshift_normal = 0, + e1000_downshift_activated, + e1000_downshift_undefined = 0xFF } e1000_downshift; typedef enum { - e1000_smart_speed_default = 0, - e1000_smart_speed_on, - e1000_smart_speed_off + e1000_smart_speed_default = 0, + e1000_smart_speed_on, + e1000_smart_speed_off } e1000_smart_speed; typedef enum { - e1000_polarity_reversal_enabled = 0, - e1000_polarity_reversal_disabled, - e1000_polarity_reversal_undefined = 0xFF + e1000_polarity_reversal_enabled = 0, + e1000_polarity_reversal_disabled, + e1000_polarity_reversal_undefined = 0xFF } e1000_polarity_reversal; typedef enum { - e1000_auto_x_mode_manual_mdi = 0, - e1000_auto_x_mode_manual_mdix, - e1000_auto_x_mode_auto1, - e1000_auto_x_mode_auto2, - e1000_auto_x_mode_undefined = 0xFF + e1000_auto_x_mode_manual_mdi = 0, + e1000_auto_x_mode_manual_mdix, + e1000_auto_x_mode_auto1, + e1000_auto_x_mode_auto2, + e1000_auto_x_mode_undefined = 0xFF } e1000_auto_x_mode; typedef enum { - e1000_1000t_rx_status_not_ok = 0, - e1000_1000t_rx_status_ok, - e1000_1000t_rx_status_undefined = 0xFF + e1000_1000t_rx_status_not_ok = 0, + e1000_1000t_rx_status_ok, + e1000_1000t_rx_status_undefined = 0xFF } e1000_1000t_rx_status; typedef enum { e1000_phy_m88 = 0, e1000_phy_igp, - e1000_phy_igp_2, - e1000_phy_gg82563, - e1000_phy_igp_3, - e1000_phy_ife, e1000_phy_undefined = 0xFF } e1000_phy_type; typedef enum { - e1000_ms_hw_default = 0, - e1000_ms_force_master, - e1000_ms_force_slave, - e1000_ms_auto + e1000_ms_hw_default = 0, + e1000_ms_force_master, + e1000_ms_force_slave, + e1000_ms_auto } e1000_ms_type; typedef enum { - e1000_ffe_config_enabled = 0, - e1000_ffe_config_active, - e1000_ffe_config_blocked + e1000_ffe_config_enabled = 0, + e1000_ffe_config_active, + e1000_ffe_config_blocked } e1000_ffe_config; typedef enum { - e1000_dsp_config_disabled = 0, - e1000_dsp_config_enabled, - e1000_dsp_config_activated, - e1000_dsp_config_undefined = 0xFF + e1000_dsp_config_disabled = 0, + e1000_dsp_config_enabled, + e1000_dsp_config_activated, + e1000_dsp_config_undefined = 0xFF } e1000_dsp_config; struct e1000_phy_info { - e1000_cable_length cable_length; - e1000_10bt_ext_dist_enable extended_10bt_distance; - e1000_rev_polarity cable_polarity; - e1000_downshift downshift; - e1000_polarity_reversal polarity_correction; - e1000_auto_x_mode mdix_mode; - e1000_1000t_rx_status local_rx; - e1000_1000t_rx_status remote_rx; + e1000_cable_length cable_length; + e1000_10bt_ext_dist_enable extended_10bt_distance; + e1000_rev_polarity cable_polarity; + e1000_downshift downshift; + e1000_polarity_reversal polarity_correction; + e1000_auto_x_mode mdix_mode; + e1000_1000t_rx_status local_rx; + e1000_1000t_rx_status remote_rx; }; struct e1000_phy_stats { - u32 idle_errors; - u32 receive_errors; + u32 idle_errors; + u32 receive_errors; }; struct e1000_eeprom_info { - e1000_eeprom_type type; - u16 word_size; - u16 opcode_bits; - u16 address_bits; - u16 delay_usec; - u16 page_size; - bool use_eerd; - bool use_eewr; + e1000_eeprom_type type; + u16 word_size; + u16 opcode_bits; + u16 address_bits; + u16 delay_usec; + u16 page_size; }; /* Flex ASF Information */ #define E1000_HOST_IF_MAX_SIZE 2048 typedef enum { - e1000_byte_align = 0, - e1000_word_align = 1, - e1000_dword_align = 2 + e1000_byte_align = 0, + e1000_word_align = 1, + e1000_dword_align = 2 } e1000_align_type; - - /* Error Codes */ #define E1000_SUCCESS 0 #define E1000_ERR_EEPROM 1 @@ -301,7 +279,6 @@ typedef enum { #define E1000_ERR_MASTER_REQUESTS_PENDING 10 #define E1000_ERR_HOST_INTERFACE_COMMAND 11 #define E1000_BLK_PHY_RESET 12 -#define E1000_ERR_SWFW_SYNC 13 #define E1000_BYTE_SWAP_WORD(_value) ((((_value) & 0x00ff) << 8) | \ (((_value) & 0xff00) >> 8)) @@ -318,19 +295,17 @@ s32 e1000_setup_link(struct e1000_hw *hw); s32 e1000_phy_setup_autoneg(struct e1000_hw *hw); void e1000_config_collision_dist(struct e1000_hw *hw); s32 e1000_check_for_link(struct e1000_hw *hw); -s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 *speed, u16 *duplex); +s32 e1000_get_speed_and_duplex(struct e1000_hw *hw, u16 * speed, u16 * duplex); s32 e1000_force_mac_fc(struct e1000_hw *hw); /* PHY */ -s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 *phy_data); +s32 e1000_read_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 * phy_data); s32 e1000_write_phy_reg(struct e1000_hw *hw, u32 reg_addr, u16 data); s32 e1000_phy_hw_reset(struct e1000_hw *hw); s32 e1000_phy_reset(struct e1000_hw *hw); s32 e1000_phy_get_info(struct e1000_hw *hw, struct e1000_phy_info *phy_info); s32 e1000_validate_mdi_setting(struct e1000_hw *hw); -void e1000_phy_powerdown_workaround(struct e1000_hw *hw); - /* EEPROM Functions */ s32 e1000_init_eeprom_params(struct e1000_hw *hw); @@ -338,66 +313,63 @@ s32 e1000_init_eeprom_params(struct e1000_hw *hw); u32 e1000_enable_mng_pass_thru(struct e1000_hw *hw); #define E1000_MNG_DHCP_TX_PAYLOAD_CMD 64 -#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */ +#define E1000_HI_MAX_MNG_DATA_LENGTH 0x6F8 /* Host Interface data length */ -#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */ -#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */ -#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */ +#define E1000_MNG_DHCP_COMMAND_TIMEOUT 10 /* Time in ms to process MNG command */ +#define E1000_MNG_DHCP_COOKIE_OFFSET 0x6F0 /* Cookie offset */ +#define E1000_MNG_DHCP_COOKIE_LENGTH 0x10 /* Cookie length */ #define E1000_MNG_IAMT_MODE 0x3 #define E1000_MNG_ICH_IAMT_MODE 0x2 -#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */ +#define E1000_IAMT_SIGNATURE 0x544D4149 /* Intel(R) Active Management Technology signature */ -#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */ -#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */ +#define E1000_MNG_DHCP_COOKIE_STATUS_PARSING_SUPPORT 0x1 /* DHCP parsing enabled */ +#define E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT 0x2 /* DHCP parsing enabled */ #define E1000_VFTA_ENTRY_SHIFT 0x5 #define E1000_VFTA_ENTRY_MASK 0x7F #define E1000_VFTA_ENTRY_BIT_SHIFT_MASK 0x1F struct e1000_host_mng_command_header { - u8 command_id; - u8 checksum; - u16 reserved1; - u16 reserved2; - u16 command_length; + u8 command_id; + u8 checksum; + u16 reserved1; + u16 reserved2; + u16 command_length; }; struct e1000_host_mng_command_info { - struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */ - u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658*/ + struct e1000_host_mng_command_header command_header; /* Command Head/Command Result Head has 4 bytes */ + u8 command_data[E1000_HI_MAX_MNG_DATA_LENGTH]; /* Command data can length 0..0x658 */ }; #ifdef __BIG_ENDIAN -struct e1000_host_mng_dhcp_cookie{ - u32 signature; - u16 vlan_id; - u8 reserved0; - u8 status; - u32 reserved1; - u8 checksum; - u8 reserved3; - u16 reserved2; +struct e1000_host_mng_dhcp_cookie { + u32 signature; + u16 vlan_id; + u8 reserved0; + u8 status; + u32 reserved1; + u8 checksum; + u8 reserved3; + u16 reserved2; }; #else -struct e1000_host_mng_dhcp_cookie{ - u32 signature; - u8 status; - u8 reserved0; - u16 vlan_id; - u32 reserved1; - u16 reserved2; - u8 reserved3; - u8 checksum; +struct e1000_host_mng_dhcp_cookie { + u32 signature; + u8 status; + u8 reserved0; + u16 vlan_id; + u32 reserved1; + u16 reserved2; + u8 reserved3; + u8 checksum; }; #endif -s32 e1000_mng_write_dhcp_info(struct e1000_hw *hw, u8 *buffer, - u16 length); bool e1000_check_mng_mode(struct e1000_hw *hw); -bool e1000_enable_tx_pkt_filtering(struct e1000_hw *hw); -s32 e1000_read_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 *data); +s32 e1000_read_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data); s32 e1000_validate_eeprom_checksum(struct e1000_hw *hw); s32 e1000_update_eeprom_checksum(struct e1000_hw *hw); -s32 e1000_write_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 *data); -s32 e1000_read_mac_addr(struct e1000_hw * hw); +s32 e1000_write_eeprom(struct e1000_hw *hw, u16 reg, u16 words, u16 * data); +s32 e1000_read_mac_addr(struct e1000_hw *hw); /* Filters (multicast, vlan, receive) */ u32 e1000_hash_mc_addr(struct e1000_hw *hw, u8 * mc_addr); @@ -417,18 +389,15 @@ s32 e1000_blink_led_start(struct e1000_hw *hw); /* Everything else */ void e1000_reset_adaptive(struct e1000_hw *hw); void e1000_update_adaptive(struct e1000_hw *hw); -void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, u32 frame_len, u8 * mac_addr); +void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, + u32 frame_len, u8 * mac_addr); void e1000_get_bus_info(struct e1000_hw *hw); void e1000_pci_set_mwi(struct e1000_hw *hw); void e1000_pci_clear_mwi(struct e1000_hw *hw); -s32 e1000_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value); void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc); int e1000_pcix_get_mmrbc(struct e1000_hw *hw); /* Port I/O is only supported on 82544 and newer */ void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value); -s32 e1000_disable_pciex_master(struct e1000_hw *hw); -s32 e1000_check_phy_reset_block(struct e1000_hw *hw); - #define E1000_READ_REG_IO(a, reg) \ e1000_read_reg_io((a), E1000_##reg) @@ -471,36 +440,7 @@ s32 e1000_check_phy_reset_block(struct e1000_hw *hw); #define E1000_DEV_ID_82546GB_QUAD_COPPER 0x1099 #define E1000_DEV_ID_82547EI 0x1019 #define E1000_DEV_ID_82547EI_MOBILE 0x101A -#define E1000_DEV_ID_82571EB_COPPER 0x105E -#define E1000_DEV_ID_82571EB_FIBER 0x105F -#define E1000_DEV_ID_82571EB_SERDES 0x1060 -#define E1000_DEV_ID_82571EB_QUAD_COPPER 0x10A4 -#define E1000_DEV_ID_82571PT_QUAD_COPPER 0x10D5 -#define E1000_DEV_ID_82571EB_QUAD_FIBER 0x10A5 -#define E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE 0x10BC -#define E1000_DEV_ID_82571EB_SERDES_DUAL 0x10D9 -#define E1000_DEV_ID_82571EB_SERDES_QUAD 0x10DA -#define E1000_DEV_ID_82572EI_COPPER 0x107D -#define E1000_DEV_ID_82572EI_FIBER 0x107E -#define E1000_DEV_ID_82572EI_SERDES 0x107F -#define E1000_DEV_ID_82572EI 0x10B9 -#define E1000_DEV_ID_82573E 0x108B -#define E1000_DEV_ID_82573E_IAMT 0x108C -#define E1000_DEV_ID_82573L 0x109A #define E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 0x10B5 -#define E1000_DEV_ID_80003ES2LAN_COPPER_DPT 0x1096 -#define E1000_DEV_ID_80003ES2LAN_SERDES_DPT 0x1098 -#define E1000_DEV_ID_80003ES2LAN_COPPER_SPT 0x10BA -#define E1000_DEV_ID_80003ES2LAN_SERDES_SPT 0x10BB - -#define E1000_DEV_ID_ICH8_IGP_M_AMT 0x1049 -#define E1000_DEV_ID_ICH8_IGP_AMT 0x104A -#define E1000_DEV_ID_ICH8_IGP_C 0x104B -#define E1000_DEV_ID_ICH8_IFE 0x104C -#define E1000_DEV_ID_ICH8_IFE_GT 0x10C4 -#define E1000_DEV_ID_ICH8_IFE_G 0x10C5 -#define E1000_DEV_ID_ICH8_IGP_M 0x104D - #define NODE_ADDRESS_SIZE 6 #define ETH_LENGTH_OF_ADDRESS 6 @@ -523,21 +463,20 @@ s32 e1000_check_phy_reset_block(struct e1000_hw *hw); /* The sizes (in bytes) of a ethernet packet */ #define ENET_HEADER_SIZE 14 -#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */ +#define MINIMUM_ETHERNET_FRAME_SIZE 64 /* With FCS */ #define ETHERNET_FCS_SIZE 4 #define MINIMUM_ETHERNET_PACKET_SIZE \ (MINIMUM_ETHERNET_FRAME_SIZE - ETHERNET_FCS_SIZE) #define CRC_LENGTH ETHERNET_FCS_SIZE #define MAX_JUMBO_FRAME_SIZE 0x3F00 - /* 802.1q VLAN Packet Sizes */ -#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */ +#define VLAN_TAG_SIZE 4 /* 802.3ac tag (not DMAed) */ /* Ethertype field values */ -#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */ -#define ETHERNET_IP_TYPE 0x0800 /* IP packets */ -#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */ +#define ETHERNET_IEEE_VLAN_TYPE 0x8100 /* 802.3ac packet */ +#define ETHERNET_IP_TYPE 0x0800 /* IP packets */ +#define ETHERNET_ARP_TYPE 0x0806 /* Address Resolution Protocol (ARP) */ /* Packet Header defines */ #define IP_PROTOCOL_TCP 6 @@ -567,15 +506,6 @@ s32 e1000_check_phy_reset_block(struct e1000_hw *hw); E1000_IMS_RXSEQ | \ E1000_IMS_LSC) -/* Additional interrupts need to be handled for e1000_ich8lan: - DSW = The FW changed the status of the DISSW bit in FWSM - PHYINT = The LAN connected device generates an interrupt - EPRST = Manageability reset event */ -#define IMS_ICH8LAN_ENABLE_MASK (\ - E1000_IMS_DSW | \ - E1000_IMS_PHYINT | \ - E1000_IMS_EPRST) - /* Number of high/low register pairs in the RAR. The RAR (Receive Address * Registers) holds the directed and multicast addresses that we monitor. We * reserve one of these spots for our directed address, allowing us room for @@ -583,100 +513,98 @@ s32 e1000_check_phy_reset_block(struct e1000_hw *hw); */ #define E1000_RAR_ENTRIES 15 -#define E1000_RAR_ENTRIES_ICH8LAN 6 - #define MIN_NUMBER_OF_DESCRIPTORS 8 #define MAX_NUMBER_OF_DESCRIPTORS 0xFFF8 /* Receive Descriptor */ struct e1000_rx_desc { - __le64 buffer_addr; /* Address of the descriptor's data buffer */ - __le16 length; /* Length of data DMAed into data buffer */ - __le16 csum; /* Packet checksum */ - u8 status; /* Descriptor status */ - u8 errors; /* Descriptor Errors */ - __le16 special; + __le64 buffer_addr; /* Address of the descriptor's data buffer */ + __le16 length; /* Length of data DMAed into data buffer */ + __le16 csum; /* Packet checksum */ + u8 status; /* Descriptor status */ + u8 errors; /* Descriptor Errors */ + __le16 special; }; /* Receive Descriptor - Extended */ union e1000_rx_desc_extended { - struct { - __le64 buffer_addr; - __le64 reserved; - } read; - struct { - struct { - __le32 mrq; /* Multiple Rx Queues */ - union { - __le32 rss; /* RSS Hash */ - struct { - __le16 ip_id; /* IP id */ - __le16 csum; /* Packet Checksum */ - } csum_ip; - } hi_dword; - } lower; - struct { - __le32 status_error; /* ext status/error */ - __le16 length; - __le16 vlan; /* VLAN tag */ - } upper; - } wb; /* writeback */ + struct { + __le64 buffer_addr; + __le64 reserved; + } read; + struct { + struct { + __le32 mrq; /* Multiple Rx Queues */ + union { + __le32 rss; /* RSS Hash */ + struct { + __le16 ip_id; /* IP id */ + __le16 csum; /* Packet Checksum */ + } csum_ip; + } hi_dword; + } lower; + struct { + __le32 status_error; /* ext status/error */ + __le16 length; + __le16 vlan; /* VLAN tag */ + } upper; + } wb; /* writeback */ }; #define MAX_PS_BUFFERS 4 /* Receive Descriptor - Packet Split */ union e1000_rx_desc_packet_split { - struct { - /* one buffer for protocol header(s), three data buffers */ - __le64 buffer_addr[MAX_PS_BUFFERS]; - } read; - struct { - struct { - __le32 mrq; /* Multiple Rx Queues */ - union { - __le32 rss; /* RSS Hash */ - struct { - __le16 ip_id; /* IP id */ - __le16 csum; /* Packet Checksum */ - } csum_ip; - } hi_dword; - } lower; - struct { - __le32 status_error; /* ext status/error */ - __le16 length0; /* length of buffer 0 */ - __le16 vlan; /* VLAN tag */ - } middle; - struct { - __le16 header_status; - __le16 length[3]; /* length of buffers 1-3 */ - } upper; - __le64 reserved; - } wb; /* writeback */ + struct { + /* one buffer for protocol header(s), three data buffers */ + __le64 buffer_addr[MAX_PS_BUFFERS]; + } read; + struct { + struct { + __le32 mrq; /* Multiple Rx Queues */ + union { + __le32 rss; /* RSS Hash */ + struct { + __le16 ip_id; /* IP id */ + __le16 csum; /* Packet Checksum */ + } csum_ip; + } hi_dword; + } lower; + struct { + __le32 status_error; /* ext status/error */ + __le16 length0; /* length of buffer 0 */ + __le16 vlan; /* VLAN tag */ + } middle; + struct { + __le16 header_status; + __le16 length[3]; /* length of buffers 1-3 */ + } upper; + __le64 reserved; + } wb; /* writeback */ }; -/* Receive Decriptor bit definitions */ -#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ -#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ -#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ -#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ -#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum caculated */ -#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ -#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */ -#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */ -#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */ -#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */ -#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */ -#define E1000_RXD_ERR_CE 0x01 /* CRC Error */ -#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ -#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ -#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ -#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ -#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ -#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ -#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ -#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */ +/* Receive Descriptor bit definitions */ +#define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */ +#define E1000_RXD_STAT_EOP 0x02 /* End of Packet */ +#define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */ +#define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */ +#define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */ +#define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */ +#define E1000_RXD_STAT_IPCS 0x40 /* IP xsum calculated */ +#define E1000_RXD_STAT_PIF 0x80 /* passed in-exact filter */ +#define E1000_RXD_STAT_IPIDV 0x200 /* IP identification valid */ +#define E1000_RXD_STAT_UDPV 0x400 /* Valid UDP checksum */ +#define E1000_RXD_STAT_ACK 0x8000 /* ACK Packet indication */ +#define E1000_RXD_ERR_CE 0x01 /* CRC Error */ +#define E1000_RXD_ERR_SE 0x02 /* Symbol Error */ +#define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */ +#define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */ +#define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */ +#define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */ +#define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */ +#define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */ +#define E1000_RXD_SPC_PRI_MASK 0xE000 /* Priority is in upper 3 bits */ #define E1000_RXD_SPC_PRI_SHIFT 13 -#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */ +#define E1000_RXD_SPC_CFI_MASK 0x1000 /* CFI is bit 12 */ #define E1000_RXD_SPC_CFI_SHIFT 12 #define E1000_RXDEXT_STATERR_CE 0x01000000 @@ -698,7 +626,6 @@ union e1000_rx_desc_packet_split { E1000_RXD_ERR_CXE | \ E1000_RXD_ERR_RXE) - /* Same mask, but for extended and packet split descriptors */ #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \ E1000_RXDEXT_STATERR_CE | \ @@ -707,152 +634,145 @@ union e1000_rx_desc_packet_split { E1000_RXDEXT_STATERR_CXE | \ E1000_RXDEXT_STATERR_RXE) - /* Transmit Descriptor */ struct e1000_tx_desc { - __le64 buffer_addr; /* Address of the descriptor's data buffer */ - union { - __le32 data; - struct { - __le16 length; /* Data buffer length */ - u8 cso; /* Checksum offset */ - u8 cmd; /* Descriptor control */ - } flags; - } lower; - union { - __le32 data; - struct { - u8 status; /* Descriptor status */ - u8 css; /* Checksum start */ - __le16 special; - } fields; - } upper; + __le64 buffer_addr; /* Address of the descriptor's data buffer */ + union { + __le32 data; + struct { + __le16 length; /* Data buffer length */ + u8 cso; /* Checksum offset */ + u8 cmd; /* Descriptor control */ + } flags; + } lower; + union { + __le32 data; + struct { + u8 status; /* Descriptor status */ + u8 css; /* Checksum start */ + __le16 special; + } fields; + } upper; }; /* Transmit Descriptor bit definitions */ -#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ -#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */ -#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ -#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ -#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ -#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ -#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ -#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ -#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ -#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */ -#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ -#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ -#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ -#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ -#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ -#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ -#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ -#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ -#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ -#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ +#define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */ +#define E1000_TXD_DTYP_C 0x00000000 /* Context Descriptor */ +#define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */ +#define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */ +#define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */ +#define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */ +#define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */ +#define E1000_TXD_CMD_RS 0x08000000 /* Report Status */ +#define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */ +#define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */ +#define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */ +#define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */ +#define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */ +#define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */ +#define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */ +#define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */ +#define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */ +#define E1000_TXD_CMD_IP 0x02000000 /* IP packet */ +#define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */ +#define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */ /* Offload Context Descriptor */ struct e1000_context_desc { - union { - __le32 ip_config; - struct { - u8 ipcss; /* IP checksum start */ - u8 ipcso; /* IP checksum offset */ - __le16 ipcse; /* IP checksum end */ - } ip_fields; - } lower_setup; - union { - __le32 tcp_config; - struct { - u8 tucss; /* TCP checksum start */ - u8 tucso; /* TCP checksum offset */ - __le16 tucse; /* TCP checksum end */ - } tcp_fields; - } upper_setup; - __le32 cmd_and_length; /* */ - union { - __le32 data; - struct { - u8 status; /* Descriptor status */ - u8 hdr_len; /* Header length */ - __le16 mss; /* Maximum segment size */ - } fields; - } tcp_seg_setup; + union { + __le32 ip_config; + struct { + u8 ipcss; /* IP checksum start */ + u8 ipcso; /* IP checksum offset */ + __le16 ipcse; /* IP checksum end */ + } ip_fields; + } lower_setup; + union { + __le32 tcp_config; + struct { + u8 tucss; /* TCP checksum start */ + u8 tucso; /* TCP checksum offset */ + __le16 tucse; /* TCP checksum end */ + } tcp_fields; + } upper_setup; + __le32 cmd_and_length; /* */ + union { + __le32 data; + struct { + u8 status; /* Descriptor status */ + u8 hdr_len; /* Header length */ + __le16 mss; /* Maximum segment size */ + } fields; + } tcp_seg_setup; }; /* Offload data descriptor */ struct e1000_data_desc { - __le64 buffer_addr; /* Address of the descriptor's buffer address */ - union { - __le32 data; - struct { - __le16 length; /* Data buffer length */ - u8 typ_len_ext; /* */ - u8 cmd; /* */ - } flags; - } lower; - union { - __le32 data; - struct { - u8 status; /* Descriptor status */ - u8 popts; /* Packet Options */ - __le16 special; /* */ - } fields; - } upper; + __le64 buffer_addr; /* Address of the descriptor's buffer address */ + union { + __le32 data; + struct { + __le16 length; /* Data buffer length */ + u8 typ_len_ext; /* */ + u8 cmd; /* */ + } flags; + } lower; + union { + __le32 data; + struct { + u8 status; /* Descriptor status */ + u8 popts; /* Packet Options */ + __le16 special; /* */ + } fields; + } upper; }; /* Filters */ -#define E1000_NUM_UNICAST 16 /* Unicast filter entries */ -#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */ -#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ - -#define E1000_NUM_UNICAST_ICH8LAN 7 -#define E1000_MC_TBL_SIZE_ICH8LAN 32 - +#define E1000_NUM_UNICAST 16 /* Unicast filter entries */ +#define E1000_MC_TBL_SIZE 128 /* Multicast Filter Table (4096 bits) */ +#define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */ /* Receive Address Register */ struct e1000_rar { - volatile __le32 low; /* receive address low */ - volatile __le32 high; /* receive address high */ + volatile __le32 low; /* receive address low */ + volatile __le32 high; /* receive address high */ }; /* Number of entries in the Multicast Table Array (MTA). */ #define E1000_NUM_MTA_REGISTERS 128 -#define E1000_NUM_MTA_REGISTERS_ICH8LAN 32 /* IPv4 Address Table Entry */ struct e1000_ipv4_at_entry { - volatile u32 ipv4_addr; /* IP Address (RW) */ - volatile u32 reserved; + volatile u32 ipv4_addr; /* IP Address (RW) */ + volatile u32 reserved; }; /* Four wakeup IP addresses are supported */ #define E1000_WAKEUP_IP_ADDRESS_COUNT_MAX 4 #define E1000_IP4AT_SIZE E1000_WAKEUP_IP_ADDRESS_COUNT_MAX -#define E1000_IP4AT_SIZE_ICH8LAN 3 #define E1000_IP6AT_SIZE 1 /* IPv6 Address Table Entry */ struct e1000_ipv6_at_entry { - volatile u8 ipv6_addr[16]; + volatile u8 ipv6_addr[16]; }; /* Flexible Filter Length Table Entry */ struct e1000_fflt_entry { - volatile u32 length; /* Flexible Filter Length (RW) */ - volatile u32 reserved; + volatile u32 length; /* Flexible Filter Length (RW) */ + volatile u32 reserved; }; /* Flexible Filter Mask Table Entry */ struct e1000_ffmt_entry { - volatile u32 mask; /* Flexible Filter Mask (RW) */ - volatile u32 reserved; + volatile u32 mask; /* Flexible Filter Mask (RW) */ + volatile u32 reserved; }; /* Flexible Filter Value Table Entry */ struct e1000_ffvt_entry { - volatile u32 value; /* Flexible Filter Value (RW) */ - volatile u32 reserved; + volatile u32 value; /* Flexible Filter Value (RW) */ + volatile u32 reserved; }; /* Four Flexible Filters are supported */ @@ -879,211 +799,211 @@ struct e1000_ffvt_entry { * R/clr - register is read only and is cleared when read * A - register array */ -#define E1000_CTRL 0x00000 /* Device Control - RW */ -#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */ -#define E1000_STATUS 0x00008 /* Device Status - RO */ -#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */ -#define E1000_EERD 0x00014 /* EEPROM Read - RW */ -#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */ -#define E1000_FLA 0x0001C /* Flash Access - RW */ -#define E1000_MDIC 0x00020 /* MDI Control - RW */ -#define E1000_SCTL 0x00024 /* SerDes Control - RW */ -#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */ -#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */ -#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */ -#define E1000_FCT 0x00030 /* Flow Control Type - RW */ -#define E1000_VET 0x00038 /* VLAN Ether Type - RW */ -#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */ -#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */ -#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */ -#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */ -#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */ -#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */ -#define E1000_RCTL 0x00100 /* RX Control - RW */ -#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */ -#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */ -#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */ -#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */ -#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */ -#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */ -#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */ -#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */ -#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */ -#define E1000_TCTL 0x00400 /* TX Control - RW */ -#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */ -#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */ -#define E1000_TBT 0x00448 /* TX Burst Timer - RW */ -#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */ -#define E1000_LEDCTL 0x00E00 /* LED Control - RW */ -#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */ -#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */ -#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */ +#define E1000_CTRL 0x00000 /* Device Control - RW */ +#define E1000_CTRL_DUP 0x00004 /* Device Control Duplicate (Shadow) - RW */ +#define E1000_STATUS 0x00008 /* Device Status - RO */ +#define E1000_EECD 0x00010 /* EEPROM/Flash Control - RW */ +#define E1000_EERD 0x00014 /* EEPROM Read - RW */ +#define E1000_CTRL_EXT 0x00018 /* Extended Device Control - RW */ +#define E1000_FLA 0x0001C /* Flash Access - RW */ +#define E1000_MDIC 0x00020 /* MDI Control - RW */ +#define E1000_SCTL 0x00024 /* SerDes Control - RW */ +#define E1000_FEXTNVM 0x00028 /* Future Extended NVM register */ +#define E1000_FCAL 0x00028 /* Flow Control Address Low - RW */ +#define E1000_FCAH 0x0002C /* Flow Control Address High -RW */ +#define E1000_FCT 0x00030 /* Flow Control Type - RW */ +#define E1000_VET 0x00038 /* VLAN Ether Type - RW */ +#define E1000_ICR 0x000C0 /* Interrupt Cause Read - R/clr */ +#define E1000_ITR 0x000C4 /* Interrupt Throttling Rate - RW */ +#define E1000_ICS 0x000C8 /* Interrupt Cause Set - WO */ +#define E1000_IMS 0x000D0 /* Interrupt Mask Set - RW */ +#define E1000_IMC 0x000D8 /* Interrupt Mask Clear - WO */ +#define E1000_IAM 0x000E0 /* Interrupt Acknowledge Auto Mask */ +#define E1000_RCTL 0x00100 /* RX Control - RW */ +#define E1000_RDTR1 0x02820 /* RX Delay Timer (1) - RW */ +#define E1000_RDBAL1 0x02900 /* RX Descriptor Base Address Low (1) - RW */ +#define E1000_RDBAH1 0x02904 /* RX Descriptor Base Address High (1) - RW */ +#define E1000_RDLEN1 0x02908 /* RX Descriptor Length (1) - RW */ +#define E1000_RDH1 0x02910 /* RX Descriptor Head (1) - RW */ +#define E1000_RDT1 0x02918 /* RX Descriptor Tail (1) - RW */ +#define E1000_FCTTV 0x00170 /* Flow Control Transmit Timer Value - RW */ +#define E1000_TXCW 0x00178 /* TX Configuration Word - RW */ +#define E1000_RXCW 0x00180 /* RX Configuration Word - RO */ +#define E1000_TCTL 0x00400 /* TX Control - RW */ +#define E1000_TCTL_EXT 0x00404 /* Extended TX Control - RW */ +#define E1000_TIPG 0x00410 /* TX Inter-packet gap -RW */ +#define E1000_TBT 0x00448 /* TX Burst Timer - RW */ +#define E1000_AIT 0x00458 /* Adaptive Interframe Spacing Throttle - RW */ +#define E1000_LEDCTL 0x00E00 /* LED Control - RW */ +#define E1000_EXTCNF_CTRL 0x00F00 /* Extended Configuration Control */ +#define E1000_EXTCNF_SIZE 0x00F08 /* Extended Configuration Size */ +#define E1000_PHY_CTRL 0x00F10 /* PHY Control Register in CSR */ #define FEXTNVM_SW_CONFIG 0x0001 -#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ -#define E1000_PBS 0x01008 /* Packet Buffer Size */ -#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ +#define E1000_PBA 0x01000 /* Packet Buffer Allocation - RW */ +#define E1000_PBS 0x01008 /* Packet Buffer Size */ +#define E1000_EEMNGCTL 0x01010 /* MNG EEprom Control */ #define E1000_FLASH_UPDATES 1000 -#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */ -#define E1000_FLASHT 0x01028 /* FLASH Timer Register */ -#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */ -#define E1000_FLSWCTL 0x01030 /* FLASH control register */ -#define E1000_FLSWDATA 0x01034 /* FLASH data register */ -#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */ -#define E1000_FLOP 0x0103C /* FLASH Opcode Register */ -#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */ -#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */ -#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */ -#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */ -#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */ -#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */ -#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */ -#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */ -#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */ -#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */ -#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */ -#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */ -#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */ -#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */ -#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */ -#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */ -#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */ -#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */ -#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */ -#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */ -#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */ -#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */ -#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */ -#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */ -#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */ -#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */ -#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */ -#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */ -#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */ -#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */ -#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */ -#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */ -#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */ -#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */ -#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */ -#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */ -#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */ -#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */ -#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */ -#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */ -#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */ -#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */ -#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */ -#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */ -#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */ -#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */ -#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */ -#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */ -#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */ -#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */ -#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */ -#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */ -#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */ -#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */ -#define E1000_COLC 0x04028 /* Collision Count - R/clr */ -#define E1000_DC 0x04030 /* Defer Count - R/clr */ -#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */ -#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */ -#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */ -#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */ -#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */ -#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */ -#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */ -#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */ -#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */ -#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */ -#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */ -#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */ -#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */ -#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */ -#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */ -#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */ -#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */ -#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */ -#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */ -#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */ -#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */ -#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */ -#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */ -#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */ -#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */ -#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */ -#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */ -#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */ -#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */ -#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */ -#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */ -#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */ -#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */ -#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */ -#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */ -#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */ -#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */ -#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */ -#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */ -#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */ -#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */ -#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */ -#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */ -#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */ -#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */ -#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */ -#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */ -#define E1000_IAC 0x04100 /* Interrupt Assertion Count */ -#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */ -#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */ -#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */ -#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */ -#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */ -#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */ -#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */ -#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */ -#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */ -#define E1000_RFCTL 0x05008 /* Receive Filter Control*/ -#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */ -#define E1000_RA 0x05400 /* Receive Address - RW Array */ -#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */ -#define E1000_WUC 0x05800 /* Wakeup Control - RW */ -#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */ -#define E1000_WUS 0x05810 /* Wakeup Status - RO */ -#define E1000_MANC 0x05820 /* Management Control - RW */ -#define E1000_IPAV 0x05838 /* IP Address Valid - RW */ -#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */ -#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */ -#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */ -#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */ -#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */ -#define E1000_HOST_IF 0x08800 /* Host Interface */ -#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */ -#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */ - -#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */ -#define E1000_MDPHYA 0x0003C /* PHY address - RW */ -#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */ -#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */ - -#define E1000_GCR 0x05B00 /* PCI-Ex Control */ -#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */ -#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */ -#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */ -#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */ -#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */ -#define E1000_SWSM 0x05B50 /* SW Semaphore */ -#define E1000_FWSM 0x05B54 /* FW Semaphore */ -#define E1000_FFLT_DBG 0x05F04 /* Debug Register */ -#define E1000_HICR 0x08F00 /* Host Inteface Control */ +#define E1000_EEARBC 0x01024 /* EEPROM Auto Read Bus Control */ +#define E1000_FLASHT 0x01028 /* FLASH Timer Register */ +#define E1000_EEWR 0x0102C /* EEPROM Write Register - RW */ +#define E1000_FLSWCTL 0x01030 /* FLASH control register */ +#define E1000_FLSWDATA 0x01034 /* FLASH data register */ +#define E1000_FLSWCNT 0x01038 /* FLASH Access Counter */ +#define E1000_FLOP 0x0103C /* FLASH Opcode Register */ +#define E1000_ERT 0x02008 /* Early Rx Threshold - RW */ +#define E1000_FCRTL 0x02160 /* Flow Control Receive Threshold Low - RW */ +#define E1000_FCRTH 0x02168 /* Flow Control Receive Threshold High - RW */ +#define E1000_PSRCTL 0x02170 /* Packet Split Receive Control - RW */ +#define E1000_RDBAL 0x02800 /* RX Descriptor Base Address Low - RW */ +#define E1000_RDBAH 0x02804 /* RX Descriptor Base Address High - RW */ +#define E1000_RDLEN 0x02808 /* RX Descriptor Length - RW */ +#define E1000_RDH 0x02810 /* RX Descriptor Head - RW */ +#define E1000_RDT 0x02818 /* RX Descriptor Tail - RW */ +#define E1000_RDTR 0x02820 /* RX Delay Timer - RW */ +#define E1000_RDBAL0 E1000_RDBAL /* RX Desc Base Address Low (0) - RW */ +#define E1000_RDBAH0 E1000_RDBAH /* RX Desc Base Address High (0) - RW */ +#define E1000_RDLEN0 E1000_RDLEN /* RX Desc Length (0) - RW */ +#define E1000_RDH0 E1000_RDH /* RX Desc Head (0) - RW */ +#define E1000_RDT0 E1000_RDT /* RX Desc Tail (0) - RW */ +#define E1000_RDTR0 E1000_RDTR /* RX Delay Timer (0) - RW */ +#define E1000_RXDCTL 0x02828 /* RX Descriptor Control queue 0 - RW */ +#define E1000_RXDCTL1 0x02928 /* RX Descriptor Control queue 1 - RW */ +#define E1000_RADV 0x0282C /* RX Interrupt Absolute Delay Timer - RW */ +#define E1000_RSRPD 0x02C00 /* RX Small Packet Detect - RW */ +#define E1000_RAID 0x02C08 /* Receive Ack Interrupt Delay - RW */ +#define E1000_TXDMAC 0x03000 /* TX DMA Control - RW */ +#define E1000_KABGTXD 0x03004 /* AFE Band Gap Transmit Ref Data */ +#define E1000_TDFH 0x03410 /* TX Data FIFO Head - RW */ +#define E1000_TDFT 0x03418 /* TX Data FIFO Tail - RW */ +#define E1000_TDFHS 0x03420 /* TX Data FIFO Head Saved - RW */ +#define E1000_TDFTS 0x03428 /* TX Data FIFO Tail Saved - RW */ +#define E1000_TDFPC 0x03430 /* TX Data FIFO Packet Count - RW */ +#define E1000_TDBAL 0x03800 /* TX Descriptor Base Address Low - RW */ +#define E1000_TDBAH 0x03804 /* TX Descriptor Base Address High - RW */ +#define E1000_TDLEN 0x03808 /* TX Descriptor Length - RW */ +#define E1000_TDH 0x03810 /* TX Descriptor Head - RW */ +#define E1000_TDT 0x03818 /* TX Descripotr Tail - RW */ +#define E1000_TIDV 0x03820 /* TX Interrupt Delay Value - RW */ +#define E1000_TXDCTL 0x03828 /* TX Descriptor Control - RW */ +#define E1000_TADV 0x0382C /* TX Interrupt Absolute Delay Val - RW */ +#define E1000_TSPMT 0x03830 /* TCP Segmentation PAD & Min Threshold - RW */ +#define E1000_TARC0 0x03840 /* TX Arbitration Count (0) */ +#define E1000_TDBAL1 0x03900 /* TX Desc Base Address Low (1) - RW */ +#define E1000_TDBAH1 0x03904 /* TX Desc Base Address High (1) - RW */ +#define E1000_TDLEN1 0x03908 /* TX Desc Length (1) - RW */ +#define E1000_TDH1 0x03910 /* TX Desc Head (1) - RW */ +#define E1000_TDT1 0x03918 /* TX Desc Tail (1) - RW */ +#define E1000_TXDCTL1 0x03928 /* TX Descriptor Control (1) - RW */ +#define E1000_TARC1 0x03940 /* TX Arbitration Count (1) */ +#define E1000_CRCERRS 0x04000 /* CRC Error Count - R/clr */ +#define E1000_ALGNERRC 0x04004 /* Alignment Error Count - R/clr */ +#define E1000_SYMERRS 0x04008 /* Symbol Error Count - R/clr */ +#define E1000_RXERRC 0x0400C /* Receive Error Count - R/clr */ +#define E1000_MPC 0x04010 /* Missed Packet Count - R/clr */ +#define E1000_SCC 0x04014 /* Single Collision Count - R/clr */ +#define E1000_ECOL 0x04018 /* Excessive Collision Count - R/clr */ +#define E1000_MCC 0x0401C /* Multiple Collision Count - R/clr */ +#define E1000_LATECOL 0x04020 /* Late Collision Count - R/clr */ +#define E1000_COLC 0x04028 /* Collision Count - R/clr */ +#define E1000_DC 0x04030 /* Defer Count - R/clr */ +#define E1000_TNCRS 0x04034 /* TX-No CRS - R/clr */ +#define E1000_SEC 0x04038 /* Sequence Error Count - R/clr */ +#define E1000_CEXTERR 0x0403C /* Carrier Extension Error Count - R/clr */ +#define E1000_RLEC 0x04040 /* Receive Length Error Count - R/clr */ +#define E1000_XONRXC 0x04048 /* XON RX Count - R/clr */ +#define E1000_XONTXC 0x0404C /* XON TX Count - R/clr */ +#define E1000_XOFFRXC 0x04050 /* XOFF RX Count - R/clr */ +#define E1000_XOFFTXC 0x04054 /* XOFF TX Count - R/clr */ +#define E1000_FCRUC 0x04058 /* Flow Control RX Unsupported Count- R/clr */ +#define E1000_PRC64 0x0405C /* Packets RX (64 bytes) - R/clr */ +#define E1000_PRC127 0x04060 /* Packets RX (65-127 bytes) - R/clr */ +#define E1000_PRC255 0x04064 /* Packets RX (128-255 bytes) - R/clr */ +#define E1000_PRC511 0x04068 /* Packets RX (255-511 bytes) - R/clr */ +#define E1000_PRC1023 0x0406C /* Packets RX (512-1023 bytes) - R/clr */ +#define E1000_PRC1522 0x04070 /* Packets RX (1024-1522 bytes) - R/clr */ +#define E1000_GPRC 0x04074 /* Good Packets RX Count - R/clr */ +#define E1000_BPRC 0x04078 /* Broadcast Packets RX Count - R/clr */ +#define E1000_MPRC 0x0407C /* Multicast Packets RX Count - R/clr */ +#define E1000_GPTC 0x04080 /* Good Packets TX Count - R/clr */ +#define E1000_GORCL 0x04088 /* Good Octets RX Count Low - R/clr */ +#define E1000_GORCH 0x0408C /* Good Octets RX Count High - R/clr */ +#define E1000_GOTCL 0x04090 /* Good Octets TX Count Low - R/clr */ +#define E1000_GOTCH 0x04094 /* Good Octets TX Count High - R/clr */ +#define E1000_RNBC 0x040A0 /* RX No Buffers Count - R/clr */ +#define E1000_RUC 0x040A4 /* RX Undersize Count - R/clr */ +#define E1000_RFC 0x040A8 /* RX Fragment Count - R/clr */ +#define E1000_ROC 0x040AC /* RX Oversize Count - R/clr */ +#define E1000_RJC 0x040B0 /* RX Jabber Count - R/clr */ +#define E1000_MGTPRC 0x040B4 /* Management Packets RX Count - R/clr */ +#define E1000_MGTPDC 0x040B8 /* Management Packets Dropped Count - R/clr */ +#define E1000_MGTPTC 0x040BC /* Management Packets TX Count - R/clr */ +#define E1000_TORL 0x040C0 /* Total Octets RX Low - R/clr */ +#define E1000_TORH 0x040C4 /* Total Octets RX High - R/clr */ +#define E1000_TOTL 0x040C8 /* Total Octets TX Low - R/clr */ +#define E1000_TOTH 0x040CC /* Total Octets TX High - R/clr */ +#define E1000_TPR 0x040D0 /* Total Packets RX - R/clr */ +#define E1000_TPT 0x040D4 /* Total Packets TX - R/clr */ +#define E1000_PTC64 0x040D8 /* Packets TX (64 bytes) - R/clr */ +#define E1000_PTC127 0x040DC /* Packets TX (65-127 bytes) - R/clr */ +#define E1000_PTC255 0x040E0 /* Packets TX (128-255 bytes) - R/clr */ +#define E1000_PTC511 0x040E4 /* Packets TX (256-511 bytes) - R/clr */ +#define E1000_PTC1023 0x040E8 /* Packets TX (512-1023 bytes) - R/clr */ +#define E1000_PTC1522 0x040EC /* Packets TX (1024-1522 Bytes) - R/clr */ +#define E1000_MPTC 0x040F0 /* Multicast Packets TX Count - R/clr */ +#define E1000_BPTC 0x040F4 /* Broadcast Packets TX Count - R/clr */ +#define E1000_TSCTC 0x040F8 /* TCP Segmentation Context TX - R/clr */ +#define E1000_TSCTFC 0x040FC /* TCP Segmentation Context TX Fail - R/clr */ +#define E1000_IAC 0x04100 /* Interrupt Assertion Count */ +#define E1000_ICRXPTC 0x04104 /* Interrupt Cause Rx Packet Timer Expire Count */ +#define E1000_ICRXATC 0x04108 /* Interrupt Cause Rx Absolute Timer Expire Count */ +#define E1000_ICTXPTC 0x0410C /* Interrupt Cause Tx Packet Timer Expire Count */ +#define E1000_ICTXATC 0x04110 /* Interrupt Cause Tx Absolute Timer Expire Count */ +#define E1000_ICTXQEC 0x04118 /* Interrupt Cause Tx Queue Empty Count */ +#define E1000_ICTXQMTC 0x0411C /* Interrupt Cause Tx Queue Minimum Threshold Count */ +#define E1000_ICRXDMTC 0x04120 /* Interrupt Cause Rx Descriptor Minimum Threshold Count */ +#define E1000_ICRXOC 0x04124 /* Interrupt Cause Receiver Overrun Count */ +#define E1000_RXCSUM 0x05000 /* RX Checksum Control - RW */ +#define E1000_RFCTL 0x05008 /* Receive Filter Control */ +#define E1000_MTA 0x05200 /* Multicast Table Array - RW Array */ +#define E1000_RA 0x05400 /* Receive Address - RW Array */ +#define E1000_VFTA 0x05600 /* VLAN Filter Table Array - RW Array */ +#define E1000_WUC 0x05800 /* Wakeup Control - RW */ +#define E1000_WUFC 0x05808 /* Wakeup Filter Control - RW */ +#define E1000_WUS 0x05810 /* Wakeup Status - RO */ +#define E1000_MANC 0x05820 /* Management Control - RW */ +#define E1000_IPAV 0x05838 /* IP Address Valid - RW */ +#define E1000_IP4AT 0x05840 /* IPv4 Address Table - RW Array */ +#define E1000_IP6AT 0x05880 /* IPv6 Address Table - RW Array */ +#define E1000_WUPL 0x05900 /* Wakeup Packet Length - RW */ +#define E1000_WUPM 0x05A00 /* Wakeup Packet Memory - RO A */ +#define E1000_FFLT 0x05F00 /* Flexible Filter Length Table - RW Array */ +#define E1000_HOST_IF 0x08800 /* Host Interface */ +#define E1000_FFMT 0x09000 /* Flexible Filter Mask Table - RW Array */ +#define E1000_FFVT 0x09800 /* Flexible Filter Value Table - RW Array */ + +#define E1000_KUMCTRLSTA 0x00034 /* MAC-PHY interface - RW */ +#define E1000_MDPHYA 0x0003C /* PHY address - RW */ +#define E1000_MANC2H 0x05860 /* Managment Control To Host - RW */ +#define E1000_SW_FW_SYNC 0x05B5C /* Software-Firmware Synchronization - RW */ + +#define E1000_GCR 0x05B00 /* PCI-Ex Control */ +#define E1000_GSCL_1 0x05B10 /* PCI-Ex Statistic Control #1 */ +#define E1000_GSCL_2 0x05B14 /* PCI-Ex Statistic Control #2 */ +#define E1000_GSCL_3 0x05B18 /* PCI-Ex Statistic Control #3 */ +#define E1000_GSCL_4 0x05B1C /* PCI-Ex Statistic Control #4 */ +#define E1000_FACTPS 0x05B30 /* Function Active and Power State to MNG */ +#define E1000_SWSM 0x05B50 /* SW Semaphore */ +#define E1000_FWSM 0x05B54 /* FW Semaphore */ +#define E1000_FFLT_DBG 0x05F04 /* Debug Register */ +#define E1000_HICR 0x08F00 /* Host Interface Control */ /* RSS registers */ -#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */ -#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */ -#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */ -#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */ -#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */ -#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */ +#define E1000_CPUVEC 0x02C10 /* CPU Vector Register - RW */ +#define E1000_MRQC 0x05818 /* Multiple Receive Control - RW */ +#define E1000_RETA 0x05C00 /* Redirection Table - RW Array */ +#define E1000_RSSRK 0x05C80 /* RSS Random Key - RW Array */ +#define E1000_RSSIM 0x05864 /* RSS Interrupt Mask */ +#define E1000_RSSIR 0x05868 /* RSS Interrupt Request */ /* Register Set (82542) * * Some of the 82542 registers are located at different offsets than they are @@ -1123,19 +1043,19 @@ struct e1000_ffvt_entry { #define E1000_82542_RDLEN0 E1000_82542_RDLEN #define E1000_82542_RDH0 E1000_82542_RDH #define E1000_82542_RDT0 E1000_82542_RDT -#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication - * RX Control - RW */ +#define E1000_82542_SRRCTL(_n) (0x280C + ((_n) << 8)) /* Split and Replication + * RX Control - RW */ #define E1000_82542_DCA_RXCTRL(_n) (0x02814 + ((_n) << 8)) -#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */ -#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */ -#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */ -#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */ -#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */ -#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */ -#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */ -#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */ -#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */ -#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */ +#define E1000_82542_RDBAH3 0x02B04 /* RX Desc Base High Queue 3 - RW */ +#define E1000_82542_RDBAL3 0x02B00 /* RX Desc Low Queue 3 - RW */ +#define E1000_82542_RDLEN3 0x02B08 /* RX Desc Length Queue 3 - RW */ +#define E1000_82542_RDH3 0x02B10 /* RX Desc Head Queue 3 - RW */ +#define E1000_82542_RDT3 0x02B18 /* RX Desc Tail Queue 3 - RW */ +#define E1000_82542_RDBAL2 0x02A00 /* RX Desc Base Low Queue 2 - RW */ +#define E1000_82542_RDBAH2 0x02A04 /* RX Desc Base High Queue 2 - RW */ +#define E1000_82542_RDLEN2 0x02A08 /* RX Desc Length Queue 2 - RW */ +#define E1000_82542_RDH2 0x02A10 /* RX Desc Head Queue 2 - RW */ +#define E1000_82542_RDT2 0x02A18 /* RX Desc Tail Queue 2 - RW */ #define E1000_82542_RDTR1 0x00130 #define E1000_82542_RDBAL1 0x00138 #define E1000_82542_RDBAH1 0x0013C @@ -1302,288 +1222,281 @@ struct e1000_ffvt_entry { #define E1000_82542_RSSIR E1000_RSSIR #define E1000_82542_KUMCTRLSTA E1000_KUMCTRLSTA #define E1000_82542_SW_FW_SYNC E1000_SW_FW_SYNC -#define E1000_82542_MANC2H E1000_MANC2H /* Statistics counters collected by the MAC */ struct e1000_hw_stats { - u64 crcerrs; - u64 algnerrc; - u64 symerrs; - u64 rxerrc; - u64 txerrc; - u64 mpc; - u64 scc; - u64 ecol; - u64 mcc; - u64 latecol; - u64 colc; - u64 dc; - u64 tncrs; - u64 sec; - u64 cexterr; - u64 rlec; - u64 xonrxc; - u64 xontxc; - u64 xoffrxc; - u64 xofftxc; - u64 fcruc; - u64 prc64; - u64 prc127; - u64 prc255; - u64 prc511; - u64 prc1023; - u64 prc1522; - u64 gprc; - u64 bprc; - u64 mprc; - u64 gptc; - u64 gorcl; - u64 gorch; - u64 gotcl; - u64 gotch; - u64 rnbc; - u64 ruc; - u64 rfc; - u64 roc; - u64 rlerrc; - u64 rjc; - u64 mgprc; - u64 mgpdc; - u64 mgptc; - u64 torl; - u64 torh; - u64 totl; - u64 toth; - u64 tpr; - u64 tpt; - u64 ptc64; - u64 ptc127; - u64 ptc255; - u64 ptc511; - u64 ptc1023; - u64 ptc1522; - u64 mptc; - u64 bptc; - u64 tsctc; - u64 tsctfc; - u64 iac; - u64 icrxptc; - u64 icrxatc; - u64 ictxptc; - u64 ictxatc; - u64 ictxqec; - u64 ictxqmtc; - u64 icrxdmtc; - u64 icrxoc; + u64 crcerrs; + u64 algnerrc; + u64 symerrs; + u64 rxerrc; + u64 txerrc; + u64 mpc; + u64 scc; + u64 ecol; + u64 mcc; + u64 latecol; + u64 colc; + u64 dc; + u64 tncrs; + u64 sec; + u64 cexterr; + u64 rlec; + u64 xonrxc; + u64 xontxc; + u64 xoffrxc; + u64 xofftxc; + u64 fcruc; + u64 prc64; + u64 prc127; + u64 prc255; + u64 prc511; + u64 prc1023; + u64 prc1522; + u64 gprc; + u64 bprc; + u64 mprc; + u64 gptc; + u64 gorcl; + u64 gorch; + u64 gotcl; + u64 gotch; + u64 rnbc; + u64 ruc; + u64 rfc; + u64 roc; + u64 rlerrc; + u64 rjc; + u64 mgprc; + u64 mgpdc; + u64 mgptc; + u64 torl; + u64 torh; + u64 totl; + u64 toth; + u64 tpr; + u64 tpt; + u64 ptc64; + u64 ptc127; + u64 ptc255; + u64 ptc511; + u64 ptc1023; + u64 ptc1522; + u64 mptc; + u64 bptc; + u64 tsctc; + u64 tsctfc; + u64 iac; + u64 icrxptc; + u64 icrxatc; + u64 ictxptc; + u64 ictxatc; + u64 ictxqec; + u64 ictxqmtc; + u64 icrxdmtc; + u64 icrxoc; }; /* Structure containing variables used by the shared code (e1000_hw.c) */ struct e1000_hw { - u8 __iomem *hw_addr; - u8 __iomem *flash_address; - e1000_mac_type mac_type; - e1000_phy_type phy_type; - u32 phy_init_script; - e1000_media_type media_type; - void *back; - struct e1000_shadow_ram *eeprom_shadow_ram; - u32 flash_bank_size; - u32 flash_base_addr; - e1000_fc_type fc; - e1000_bus_speed bus_speed; - e1000_bus_width bus_width; - e1000_bus_type bus_type; + u8 __iomem *hw_addr; + u8 __iomem *flash_address; + e1000_mac_type mac_type; + e1000_phy_type phy_type; + u32 phy_init_script; + e1000_media_type media_type; + void *back; + struct e1000_shadow_ram *eeprom_shadow_ram; + u32 flash_bank_size; + u32 flash_base_addr; + e1000_fc_type fc; + e1000_bus_speed bus_speed; + e1000_bus_width bus_width; + e1000_bus_type bus_type; struct e1000_eeprom_info eeprom; - e1000_ms_type master_slave; - e1000_ms_type original_master_slave; - e1000_ffe_config ffe_config_state; - u32 asf_firmware_present; - u32 eeprom_semaphore_present; - u32 swfw_sync_present; - u32 swfwhw_semaphore_present; - unsigned long io_base; - u32 phy_id; - u32 phy_revision; - u32 phy_addr; - u32 original_fc; - u32 txcw; - u32 autoneg_failed; - u32 max_frame_size; - u32 min_frame_size; - u32 mc_filter_type; - u32 num_mc_addrs; - u32 collision_delta; - u32 tx_packet_delta; - u32 ledctl_default; - u32 ledctl_mode1; - u32 ledctl_mode2; - bool tx_pkt_filtering; + e1000_ms_type master_slave; + e1000_ms_type original_master_slave; + e1000_ffe_config ffe_config_state; + u32 asf_firmware_present; + u32 eeprom_semaphore_present; + unsigned long io_base; + u32 phy_id; + u32 phy_revision; + u32 phy_addr; + u32 original_fc; + u32 txcw; + u32 autoneg_failed; + u32 max_frame_size; + u32 min_frame_size; + u32 mc_filter_type; + u32 num_mc_addrs; + u32 collision_delta; + u32 tx_packet_delta; + u32 ledctl_default; + u32 ledctl_mode1; + u32 ledctl_mode2; + bool tx_pkt_filtering; struct e1000_host_mng_dhcp_cookie mng_cookie; - u16 phy_spd_default; - u16 autoneg_advertised; - u16 pci_cmd_word; - u16 fc_high_water; - u16 fc_low_water; - u16 fc_pause_time; - u16 current_ifs_val; - u16 ifs_min_val; - u16 ifs_max_val; - u16 ifs_step_size; - u16 ifs_ratio; - u16 device_id; - u16 vendor_id; - u16 subsystem_id; - u16 subsystem_vendor_id; - u8 revision_id; - u8 autoneg; - u8 mdix; - u8 forced_speed_duplex; - u8 wait_autoneg_complete; - u8 dma_fairness; - u8 mac_addr[NODE_ADDRESS_SIZE]; - u8 perm_mac_addr[NODE_ADDRESS_SIZE]; - bool disable_polarity_correction; - bool speed_downgraded; - e1000_smart_speed smart_speed; - e1000_dsp_config dsp_config_state; - bool get_link_status; - bool serdes_link_down; - bool tbi_compatibility_en; - bool tbi_compatibility_on; - bool laa_is_present; - bool phy_reset_disable; - bool initialize_hw_bits_disable; - bool fc_send_xon; - bool fc_strict_ieee; - bool report_tx_early; - bool adaptive_ifs; - bool ifs_params_forced; - bool in_ifs_mode; - bool mng_reg_access_disabled; - bool leave_av_bit_off; - bool kmrn_lock_loss_workaround_disabled; - bool bad_tx_carr_stats_fd; - bool has_manc2h; - bool rx_needs_kicking; - bool has_smbus; + u16 phy_spd_default; + u16 autoneg_advertised; + u16 pci_cmd_word; + u16 fc_high_water; + u16 fc_low_water; + u16 fc_pause_time; + u16 current_ifs_val; + u16 ifs_min_val; + u16 ifs_max_val; + u16 ifs_step_size; + u16 ifs_ratio; + u16 device_id; + u16 vendor_id; + u16 subsystem_id; + u16 subsystem_vendor_id; + u8 revision_id; + u8 autoneg; + u8 mdix; + u8 forced_speed_duplex; + u8 wait_autoneg_complete; + u8 dma_fairness; + u8 mac_addr[NODE_ADDRESS_SIZE]; + u8 perm_mac_addr[NODE_ADDRESS_SIZE]; + bool disable_polarity_correction; + bool speed_downgraded; + e1000_smart_speed smart_speed; + e1000_dsp_config dsp_config_state; + bool get_link_status; + bool serdes_has_link; + bool tbi_compatibility_en; + bool tbi_compatibility_on; + bool laa_is_present; + bool phy_reset_disable; + bool initialize_hw_bits_disable; + bool fc_send_xon; + bool fc_strict_ieee; + bool report_tx_early; + bool adaptive_ifs; + bool ifs_params_forced; + bool in_ifs_mode; + bool mng_reg_access_disabled; + bool leave_av_bit_off; + bool bad_tx_carr_stats_fd; + bool has_smbus; }; - -#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */ -#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */ -#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */ -#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */ -#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */ -#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */ -#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */ -#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */ +#define E1000_EEPROM_SWDPIN0 0x0001 /* SWDPIN 0 EEPROM Value */ +#define E1000_EEPROM_LED_LOGIC 0x0020 /* Led Logic Word */ +#define E1000_EEPROM_RW_REG_DATA 16 /* Offset to data in EEPROM read/write registers */ +#define E1000_EEPROM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */ +#define E1000_EEPROM_RW_REG_START 1 /* First bit for telling part to start operation */ +#define E1000_EEPROM_RW_ADDR_SHIFT 2 /* Shift to the address bits */ +#define E1000_EEPROM_POLL_WRITE 1 /* Flag for polling for write complete */ +#define E1000_EEPROM_POLL_READ 0 /* Flag for polling for read complete */ /* Register Bit Masks */ /* Device Control */ -#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ -#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */ -#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */ -#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */ -#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */ -#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */ -#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */ -#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ -#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ -#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ -#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ -#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ -#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ -#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ -#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */ -#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ -#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ -#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */ -#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */ -#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */ -#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */ -#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ -#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ -#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ -#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */ -#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ -#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */ -#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */ -#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */ -#define E1000_CTRL_RST 0x04000000 /* Global reset */ -#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ -#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ -#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */ -#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ -#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ -#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */ +#define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */ +#define E1000_CTRL_BEM 0x00000002 /* Endian Mode.0=little,1=big */ +#define E1000_CTRL_PRIOR 0x00000004 /* Priority on PCI. 0=rx,1=fair */ +#define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */ +#define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */ +#define E1000_CTRL_TME 0x00000010 /* Test mode. 0=normal,1=test */ +#define E1000_CTRL_SLE 0x00000020 /* Serial Link on 0=dis,1=en */ +#define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */ +#define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */ +#define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */ +#define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */ +#define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */ +#define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */ +#define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */ +#define E1000_CTRL_BEM32 0x00000400 /* Big Endian 32 mode */ +#define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */ +#define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */ +#define E1000_CTRL_D_UD_EN 0x00002000 /* Dock/Undock enable */ +#define E1000_CTRL_D_UD_POLARITY 0x00004000 /* Defined polarity of Dock/Undock indication in SDP[0] */ +#define E1000_CTRL_FORCE_PHY_RESET 0x00008000 /* Reset both PHY ports, through PHYRST_N pin */ +#define E1000_CTRL_EXT_LINK_EN 0x00010000 /* enable link status from external LINK_0 and LINK_1 pins */ +#define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */ +#define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */ +#define E1000_CTRL_SWDPIN2 0x00100000 /* SWDPIN 2 value */ +#define E1000_CTRL_SWDPIN3 0x00200000 /* SWDPIN 3 value */ +#define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */ +#define E1000_CTRL_SWDPIO1 0x00800000 /* SWDPIN 1 input or output */ +#define E1000_CTRL_SWDPIO2 0x01000000 /* SWDPIN 2 input or output */ +#define E1000_CTRL_SWDPIO3 0x02000000 /* SWDPIN 3 input or output */ +#define E1000_CTRL_RST 0x04000000 /* Global reset */ +#define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */ +#define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */ +#define E1000_CTRL_RTE 0x20000000 /* Routing tag enable */ +#define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */ +#define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */ +#define E1000_CTRL_SW2FW_INT 0x02000000 /* Initiate an interrupt to manageability engine */ /* Device Status */ -#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ -#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ -#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */ +#define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */ +#define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */ +#define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */ #define E1000_STATUS_FUNC_SHIFT 2 -#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */ -#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */ -#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ -#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */ +#define E1000_STATUS_FUNC_0 0x00000000 /* Function 0 */ +#define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */ +#define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */ +#define E1000_STATUS_TBIMODE 0x00000020 /* TBI mode */ #define E1000_STATUS_SPEED_MASK 0x000000C0 -#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ -#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ -#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ -#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion - by EEPROM/Flash */ -#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */ -#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */ -#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */ -#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */ -#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */ -#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */ -#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */ -#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */ -#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */ -#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */ -#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */ -#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */ -#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */ -#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */ +#define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */ +#define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */ +#define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */ +#define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion + by EEPROM/Flash */ +#define E1000_STATUS_ASDV 0x00000300 /* Auto speed detect value */ +#define E1000_STATUS_DOCK_CI 0x00000800 /* Change in Dock/Undock state. Clear on write '0'. */ +#define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Status of Master requests. */ +#define E1000_STATUS_MTXCKOK 0x00000400 /* MTX clock running OK */ +#define E1000_STATUS_PCI66 0x00000800 /* In 66Mhz slot */ +#define E1000_STATUS_BUS64 0x00001000 /* In 64 bit slot */ +#define E1000_STATUS_PCIX_MODE 0x00002000 /* PCI-X mode */ +#define E1000_STATUS_PCIX_SPEED 0x0000C000 /* PCI-X bus speed */ +#define E1000_STATUS_BMC_SKU_0 0x00100000 /* BMC USB redirect disabled */ +#define E1000_STATUS_BMC_SKU_1 0x00200000 /* BMC SRAM disabled */ +#define E1000_STATUS_BMC_SKU_2 0x00400000 /* BMC SDRAM disabled */ +#define E1000_STATUS_BMC_CRYPTO 0x00800000 /* BMC crypto disabled */ +#define E1000_STATUS_BMC_LITE 0x01000000 /* BMC external code execution disabled */ +#define E1000_STATUS_RGMII_ENABLE 0x02000000 /* RGMII disabled */ #define E1000_STATUS_FUSE_8 0x04000000 #define E1000_STATUS_FUSE_9 0x08000000 -#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */ -#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */ +#define E1000_STATUS_SERDES0_DIS 0x10000000 /* SERDES disabled on port 0 */ +#define E1000_STATUS_SERDES1_DIS 0x20000000 /* SERDES disabled on port 1 */ -/* Constants used to intrepret the masked PCI-X bus speed. */ -#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */ -#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */ -#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */ +/* Constants used to interpret the masked PCI-X bus speed. */ +#define E1000_STATUS_PCIX_SPEED_66 0x00000000 /* PCI-X bus speed 50-66 MHz */ +#define E1000_STATUS_PCIX_SPEED_100 0x00004000 /* PCI-X bus speed 66-100 MHz */ +#define E1000_STATUS_PCIX_SPEED_133 0x00008000 /* PCI-X bus speed 100-133 MHz */ /* EEPROM/Flash Control */ -#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */ -#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */ -#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */ -#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */ +#define E1000_EECD_SK 0x00000001 /* EEPROM Clock */ +#define E1000_EECD_CS 0x00000002 /* EEPROM Chip Select */ +#define E1000_EECD_DI 0x00000004 /* EEPROM Data In */ +#define E1000_EECD_DO 0x00000008 /* EEPROM Data Out */ #define E1000_EECD_FWE_MASK 0x00000030 -#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */ -#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */ +#define E1000_EECD_FWE_DIS 0x00000010 /* Disable FLASH writes */ +#define E1000_EECD_FWE_EN 0x00000020 /* Enable FLASH writes */ #define E1000_EECD_FWE_SHIFT 4 -#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */ -#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */ -#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */ -#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */ -#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type - * (0-small, 1-large) */ -#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */ +#define E1000_EECD_REQ 0x00000040 /* EEPROM Access Request */ +#define E1000_EECD_GNT 0x00000080 /* EEPROM Access Grant */ +#define E1000_EECD_PRES 0x00000100 /* EEPROM Present */ +#define E1000_EECD_SIZE 0x00000200 /* EEPROM Size (0=64 word 1=256 word) */ +#define E1000_EECD_ADDR_BITS 0x00000400 /* EEPROM Addressing bits based on type + * (0-small, 1-large) */ +#define E1000_EECD_TYPE 0x00002000 /* EEPROM Type (1-SPI, 0-Microwire) */ #ifndef E1000_EEPROM_GRANT_ATTEMPTS -#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */ +#define E1000_EEPROM_GRANT_ATTEMPTS 1000 /* EEPROM # attempts to gain grant */ #endif -#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */ -#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */ +#define E1000_EECD_AUTO_RD 0x00000200 /* EEPROM Auto Read done */ +#define E1000_EECD_SIZE_EX_MASK 0x00007800 /* EEprom Size */ #define E1000_EECD_SIZE_EX_SHIFT 11 -#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */ -#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */ -#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */ -#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */ -#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */ -#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */ -#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */ +#define E1000_EECD_NVADDS 0x00018000 /* NVM Address Size */ +#define E1000_EECD_SELSHAD 0x00020000 /* Select Shadow RAM */ +#define E1000_EECD_INITSRAM 0x00040000 /* Initialize Shadow RAM */ +#define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */ +#define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */ +#define E1000_EECD_SHADV 0x00200000 /* Shadow RAM Data Valid */ +#define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */ #define E1000_EECD_SECVAL_SHIFT 22 #define E1000_STM_OPCODE 0xDB00 #define E1000_HICR_FW_RESET 0xC0 @@ -1593,12 +1506,12 @@ struct e1000_hw { #define E1000_ICH_NVM_SIG_MASK 0xC0 /* EEPROM Read */ -#define E1000_EERD_START 0x00000001 /* Start Read */ -#define E1000_EERD_DONE 0x00000010 /* Read Done */ +#define E1000_EERD_START 0x00000001 /* Start Read */ +#define E1000_EERD_DONE 0x00000010 /* Read Done */ #define E1000_EERD_ADDR_SHIFT 8 -#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */ +#define E1000_EERD_ADDR_MASK 0x0000FF00 /* Read Address */ #define E1000_EERD_DATA_SHIFT 16 -#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */ +#define E1000_EERD_DATA_MASK 0xFFFF0000 /* Read Data */ /* SPI EEPROM Status Register */ #define EEPROM_STATUS_RDY_SPI 0x01 @@ -1608,25 +1521,25 @@ struct e1000_hw { #define EEPROM_STATUS_WPEN_SPI 0x80 /* Extended Device Control */ -#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */ -#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */ +#define E1000_CTRL_EXT_GPI0_EN 0x00000001 /* Maps SDP4 to GPI0 */ +#define E1000_CTRL_EXT_GPI1_EN 0x00000002 /* Maps SDP5 to GPI1 */ #define E1000_CTRL_EXT_PHYINT_EN E1000_CTRL_EXT_GPI1_EN -#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */ -#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */ -#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */ -#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */ +#define E1000_CTRL_EXT_GPI2_EN 0x00000004 /* Maps SDP6 to GPI2 */ +#define E1000_CTRL_EXT_GPI3_EN 0x00000008 /* Maps SDP7 to GPI3 */ +#define E1000_CTRL_EXT_SDP4_DATA 0x00000010 /* Value of SW Defineable Pin 4 */ +#define E1000_CTRL_EXT_SDP5_DATA 0x00000020 /* Value of SW Defineable Pin 5 */ #define E1000_CTRL_EXT_PHY_INT E1000_CTRL_EXT_SDP5_DATA -#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */ -#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */ -#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */ -#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */ -#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */ -#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */ -#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */ -#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ -#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */ -#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ -#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ +#define E1000_CTRL_EXT_SDP6_DATA 0x00000040 /* Value of SW Defineable Pin 6 */ +#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */ +#define E1000_CTRL_EXT_SDP4_DIR 0x00000100 /* Direction of SDP4 0=in 1=out */ +#define E1000_CTRL_EXT_SDP5_DIR 0x00000200 /* Direction of SDP5 0=in 1=out */ +#define E1000_CTRL_EXT_SDP6_DIR 0x00000400 /* Direction of SDP6 0=in 1=out */ +#define E1000_CTRL_EXT_SDP7_DIR 0x00000800 /* Direction of SDP7 0=in 1=out */ +#define E1000_CTRL_EXT_ASDCHK 0x00001000 /* Initiate an ASD sequence */ +#define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */ +#define E1000_CTRL_EXT_IPS 0x00004000 /* Invert Power State */ +#define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */ +#define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */ #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 #define E1000_CTRL_EXT_LINK_MODE_GMII 0x00000000 #define E1000_CTRL_EXT_LINK_MODE_TBI 0x00C00000 @@ -1638,11 +1551,11 @@ struct e1000_hw { #define E1000_CTRL_EXT_WR_WMARK_320 0x01000000 #define E1000_CTRL_EXT_WR_WMARK_384 0x02000000 #define E1000_CTRL_EXT_WR_WMARK_448 0x03000000 -#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ -#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */ -#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */ -#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */ -#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */ +#define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */ +#define E1000_CTRL_EXT_IAME 0x08000000 /* Interrupt acknowledge Auto-mask */ +#define E1000_CTRL_EXT_INT_TIMER_CLR 0x20000000 /* Clear Interrupt timers after IMS clear */ +#define E1000_CRTL_EXT_PB_PAREN 0x01000000 /* packet buffer parity error detection enabled */ +#define E1000_CTRL_EXT_DF_PAREN 0x02000000 /* descriptor FIFO parity error detection enable */ #define E1000_CTRL_EXT_GHOST_PAREN 0x40000000 /* MDI Control */ @@ -1742,167 +1655,167 @@ struct e1000_hw { #define E1000_LEDCTL_MODE_LED_OFF 0xF /* Receive Address */ -#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */ +#define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */ /* Interrupt Cause Read */ -#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ -#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */ -#define E1000_ICR_LSC 0x00000004 /* Link Status Change */ -#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */ -#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */ -#define E1000_ICR_RXO 0x00000040 /* rx overrun */ -#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */ -#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */ -#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */ -#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */ -#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */ -#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */ -#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */ +#define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */ +#define E1000_ICR_TXQE 0x00000002 /* Transmit Queue empty */ +#define E1000_ICR_LSC 0x00000004 /* Link Status Change */ +#define E1000_ICR_RXSEQ 0x00000008 /* rx sequence error */ +#define E1000_ICR_RXDMT0 0x00000010 /* rx desc min. threshold (0) */ +#define E1000_ICR_RXO 0x00000040 /* rx overrun */ +#define E1000_ICR_RXT0 0x00000080 /* rx timer intr (ring 0) */ +#define E1000_ICR_MDAC 0x00000200 /* MDIO access complete */ +#define E1000_ICR_RXCFG 0x00000400 /* RX /c/ ordered set */ +#define E1000_ICR_GPI_EN0 0x00000800 /* GP Int 0 */ +#define E1000_ICR_GPI_EN1 0x00001000 /* GP Int 1 */ +#define E1000_ICR_GPI_EN2 0x00002000 /* GP Int 2 */ +#define E1000_ICR_GPI_EN3 0x00004000 /* GP Int 3 */ #define E1000_ICR_TXD_LOW 0x00008000 #define E1000_ICR_SRPD 0x00010000 -#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */ -#define E1000_ICR_MNG 0x00040000 /* Manageability event */ -#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ -#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */ -#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */ -#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ -#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */ -#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ -#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */ -#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */ -#define E1000_ICR_EPRST 0x00100000 /* ME handware reset occurs */ +#define E1000_ICR_ACK 0x00020000 /* Receive Ack frame */ +#define E1000_ICR_MNG 0x00040000 /* Manageability event */ +#define E1000_ICR_DOCK 0x00080000 /* Dock/Undock */ +#define E1000_ICR_INT_ASSERTED 0x80000000 /* If this bit asserted, the driver should claim the interrupt */ +#define E1000_ICR_RXD_FIFO_PAR0 0x00100000 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_ICR_TXD_FIFO_PAR0 0x00200000 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_ICR_HOST_ARB_PAR 0x00400000 /* host arb read buffer parity error */ +#define E1000_ICR_PB_PAR 0x00800000 /* packet buffer parity error */ +#define E1000_ICR_RXD_FIFO_PAR1 0x01000000 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_ICR_TXD_FIFO_PAR1 0x02000000 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_ICR_ALL_PARITY 0x03F00000 /* all parity error bits */ +#define E1000_ICR_DSW 0x00000020 /* FW changed the status of DISSW bit in the FWSM */ +#define E1000_ICR_PHYINT 0x00001000 /* LAN connected device generates an interrupt */ +#define E1000_ICR_EPRST 0x00100000 /* ME hardware reset occurs */ /* Interrupt Cause Set */ -#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ -#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ -#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ -#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ -#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ -#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */ -#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ -#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */ -#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ -#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ -#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ -#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ -#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ +#define E1000_ICS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ +#define E1000_ICS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ +#define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */ +#define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ +#define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ +#define E1000_ICS_RXO E1000_ICR_RXO /* rx overrun */ +#define E1000_ICS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ +#define E1000_ICS_MDAC E1000_ICR_MDAC /* MDIO access complete */ +#define E1000_ICS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ +#define E1000_ICS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ +#define E1000_ICS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ +#define E1000_ICS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ +#define E1000_ICS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ #define E1000_ICS_TXD_LOW E1000_ICR_TXD_LOW #define E1000_ICS_SRPD E1000_ICR_SRPD -#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */ -#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */ -#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_ICS_ACK E1000_ICR_ACK /* Receive Ack frame */ +#define E1000_ICS_MNG E1000_ICR_MNG /* Manageability event */ +#define E1000_ICS_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_ICS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_ICS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_ICS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ +#define E1000_ICS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ +#define E1000_ICS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_ICS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ #define E1000_ICS_DSW E1000_ICR_DSW #define E1000_ICS_PHYINT E1000_ICR_PHYINT #define E1000_ICS_EPRST E1000_ICR_EPRST /* Interrupt Mask Set */ -#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ -#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ -#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */ -#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ -#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ -#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */ -#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ -#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */ -#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ -#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ -#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ -#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ -#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ +#define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */ +#define E1000_IMS_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ +#define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */ +#define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ +#define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ +#define E1000_IMS_RXO E1000_ICR_RXO /* rx overrun */ +#define E1000_IMS_RXT0 E1000_ICR_RXT0 /* rx timer intr */ +#define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO access complete */ +#define E1000_IMS_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ +#define E1000_IMS_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ +#define E1000_IMS_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ +#define E1000_IMS_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ +#define E1000_IMS_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ #define E1000_IMS_TXD_LOW E1000_ICR_TXD_LOW #define E1000_IMS_SRPD E1000_ICR_SRPD -#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */ -#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */ -#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_IMS_ACK E1000_ICR_ACK /* Receive Ack frame */ +#define E1000_IMS_MNG E1000_ICR_MNG /* Manageability event */ +#define E1000_IMS_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_IMS_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_IMS_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_IMS_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ +#define E1000_IMS_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ +#define E1000_IMS_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_IMS_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ #define E1000_IMS_DSW E1000_ICR_DSW #define E1000_IMS_PHYINT E1000_ICR_PHYINT #define E1000_IMS_EPRST E1000_ICR_EPRST /* Interrupt Mask Clear */ -#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */ -#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ -#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */ -#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ -#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ -#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */ -#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */ -#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */ -#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ -#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ -#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ -#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ -#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ +#define E1000_IMC_TXDW E1000_ICR_TXDW /* Transmit desc written back */ +#define E1000_IMC_TXQE E1000_ICR_TXQE /* Transmit Queue empty */ +#define E1000_IMC_LSC E1000_ICR_LSC /* Link Status Change */ +#define E1000_IMC_RXSEQ E1000_ICR_RXSEQ /* rx sequence error */ +#define E1000_IMC_RXDMT0 E1000_ICR_RXDMT0 /* rx desc min. threshold */ +#define E1000_IMC_RXO E1000_ICR_RXO /* rx overrun */ +#define E1000_IMC_RXT0 E1000_ICR_RXT0 /* rx timer intr */ +#define E1000_IMC_MDAC E1000_ICR_MDAC /* MDIO access complete */ +#define E1000_IMC_RXCFG E1000_ICR_RXCFG /* RX /c/ ordered set */ +#define E1000_IMC_GPI_EN0 E1000_ICR_GPI_EN0 /* GP Int 0 */ +#define E1000_IMC_GPI_EN1 E1000_ICR_GPI_EN1 /* GP Int 1 */ +#define E1000_IMC_GPI_EN2 E1000_ICR_GPI_EN2 /* GP Int 2 */ +#define E1000_IMC_GPI_EN3 E1000_ICR_GPI_EN3 /* GP Int 3 */ #define E1000_IMC_TXD_LOW E1000_ICR_TXD_LOW #define E1000_IMC_SRPD E1000_ICR_SRPD -#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */ -#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */ -#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */ -#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ -#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ -#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ -#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ -#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ -#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ +#define E1000_IMC_ACK E1000_ICR_ACK /* Receive Ack frame */ +#define E1000_IMC_MNG E1000_ICR_MNG /* Manageability event */ +#define E1000_IMC_DOCK E1000_ICR_DOCK /* Dock/Undock */ +#define E1000_IMC_RXD_FIFO_PAR0 E1000_ICR_RXD_FIFO_PAR0 /* queue 0 Rx descriptor FIFO parity error */ +#define E1000_IMC_TXD_FIFO_PAR0 E1000_ICR_TXD_FIFO_PAR0 /* queue 0 Tx descriptor FIFO parity error */ +#define E1000_IMC_HOST_ARB_PAR E1000_ICR_HOST_ARB_PAR /* host arb read buffer parity error */ +#define E1000_IMC_PB_PAR E1000_ICR_PB_PAR /* packet buffer parity error */ +#define E1000_IMC_RXD_FIFO_PAR1 E1000_ICR_RXD_FIFO_PAR1 /* queue 1 Rx descriptor FIFO parity error */ +#define E1000_IMC_TXD_FIFO_PAR1 E1000_ICR_TXD_FIFO_PAR1 /* queue 1 Tx descriptor FIFO parity error */ #define E1000_IMC_DSW E1000_ICR_DSW #define E1000_IMC_PHYINT E1000_ICR_PHYINT #define E1000_IMC_EPRST E1000_ICR_EPRST /* Receive Control */ -#define E1000_RCTL_RST 0x00000001 /* Software reset */ -#define E1000_RCTL_EN 0x00000002 /* enable */ -#define E1000_RCTL_SBP 0x00000004 /* store bad packet */ -#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */ -#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */ -#define E1000_RCTL_LPE 0x00000020 /* long packet enable */ -#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ -#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ -#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */ -#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ -#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */ -#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ -#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */ -#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */ -#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */ -#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ -#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */ -#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */ -#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */ -#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ -#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */ -#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ +#define E1000_RCTL_RST 0x00000001 /* Software reset */ +#define E1000_RCTL_EN 0x00000002 /* enable */ +#define E1000_RCTL_SBP 0x00000004 /* store bad packet */ +#define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */ +#define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */ +#define E1000_RCTL_LPE 0x00000020 /* long packet enable */ +#define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */ +#define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */ +#define E1000_RCTL_LBM_SLP 0x00000080 /* serial link loopback mode */ +#define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */ +#define E1000_RCTL_DTYP_MASK 0x00000C00 /* Descriptor type mask */ +#define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */ +#define E1000_RCTL_RDMTS_HALF 0x00000000 /* rx desc min threshold size */ +#define E1000_RCTL_RDMTS_QUAT 0x00000100 /* rx desc min threshold size */ +#define E1000_RCTL_RDMTS_EIGTH 0x00000200 /* rx desc min threshold size */ +#define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */ +#define E1000_RCTL_MO_0 0x00000000 /* multicast offset 11:0 */ +#define E1000_RCTL_MO_1 0x00001000 /* multicast offset 12:1 */ +#define E1000_RCTL_MO_2 0x00002000 /* multicast offset 13:2 */ +#define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */ +#define E1000_RCTL_MDR 0x00004000 /* multicast desc ring 0 */ +#define E1000_RCTL_BAM 0x00008000 /* broadcast enable */ /* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */ -#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */ -#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */ -#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */ -#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */ +#define E1000_RCTL_SZ_2048 0x00000000 /* rx buffer size 2048 */ +#define E1000_RCTL_SZ_1024 0x00010000 /* rx buffer size 1024 */ +#define E1000_RCTL_SZ_512 0x00020000 /* rx buffer size 512 */ +#define E1000_RCTL_SZ_256 0x00030000 /* rx buffer size 256 */ /* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */ -#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */ -#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */ -#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */ -#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ -#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ -#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ -#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */ -#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ -#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ -#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ -#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */ -#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */ +#define E1000_RCTL_SZ_16384 0x00010000 /* rx buffer size 16384 */ +#define E1000_RCTL_SZ_8192 0x00020000 /* rx buffer size 8192 */ +#define E1000_RCTL_SZ_4096 0x00030000 /* rx buffer size 4096 */ +#define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */ +#define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */ +#define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */ +#define E1000_RCTL_DPF 0x00400000 /* discard pause frames */ +#define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */ +#define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */ +#define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */ +#define E1000_RCTL_FLXBUF_MASK 0x78000000 /* Flexible buffer size */ +#define E1000_RCTL_FLXBUF_SHIFT 27 /* Flexible buffer shift */ /* Use byte values for the following shift parameters * Usage: @@ -1925,10 +1838,10 @@ struct e1000_hw { #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000 #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000 -#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */ -#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */ -#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ -#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ +#define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */ +#define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */ +#define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */ +#define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */ /* SW_W_SYNC definitions */ #define E1000_SWFW_EEP_SM 0x0001 @@ -1937,17 +1850,17 @@ struct e1000_hw { #define E1000_SWFW_MAC_CSR_SM 0x0008 /* Receive Descriptor */ -#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */ -#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */ -#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */ -#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */ -#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */ +#define E1000_RDT_DELAY 0x0000ffff /* Delay timer (1=1024us) */ +#define E1000_RDT_FPDB 0x80000000 /* Flush descriptor block */ +#define E1000_RDLEN_LEN 0x0007ff80 /* descriptor length */ +#define E1000_RDH_RDH 0x0000ffff /* receive descriptor head */ +#define E1000_RDT_RDT 0x0000ffff /* receive descriptor tail */ /* Flow Control */ -#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ -#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */ -#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ -#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ +#define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */ +#define E1000_FCRTH_XFCE 0x80000000 /* External Flow Control Enable */ +#define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */ +#define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */ /* Header split receive */ #define E1000_RFCTL_ISCSI_DIS 0x00000001 @@ -1967,66 +1880,64 @@ struct e1000_hw { #define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000 /* Receive Descriptor Control */ -#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */ -#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */ -#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */ -#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */ +#define E1000_RXDCTL_PTHRESH 0x0000003F /* RXDCTL Prefetch Threshold */ +#define E1000_RXDCTL_HTHRESH 0x00003F00 /* RXDCTL Host Threshold */ +#define E1000_RXDCTL_WTHRESH 0x003F0000 /* RXDCTL Writeback Threshold */ +#define E1000_RXDCTL_GRAN 0x01000000 /* RXDCTL Granularity */ /* Transmit Descriptor Control */ -#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */ -#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */ -#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */ -#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */ -#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */ -#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */ -#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc. - still to be processed. */ +#define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */ +#define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */ +#define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */ +#define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */ +#define E1000_TXDCTL_LWTHRESH 0xFE000000 /* TXDCTL Low Threshold */ +#define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */ +#define E1000_TXDCTL_COUNT_DESC 0x00400000 /* Enable the counting of desc. + still to be processed. */ /* Transmit Configuration Word */ -#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */ -#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */ -#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ -#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ -#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */ -#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */ -#define E1000_TXCW_NP 0x00008000 /* TXCW next page */ -#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */ -#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */ -#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ +#define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */ +#define E1000_TXCW_HD 0x00000040 /* TXCW half duplex */ +#define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */ +#define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */ +#define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */ +#define E1000_TXCW_RF 0x00003000 /* TXCW remote fault */ +#define E1000_TXCW_NP 0x00008000 /* TXCW next page */ +#define E1000_TXCW_CW 0x0000ffff /* TxConfigWord mask */ +#define E1000_TXCW_TXC 0x40000000 /* Transmit Config control */ +#define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */ /* Receive Configuration Word */ -#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */ -#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */ -#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */ -#define E1000_RXCW_CC 0x10000000 /* Receive config change */ -#define E1000_RXCW_C 0x20000000 /* Receive config */ -#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */ -#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */ +#define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */ +#define E1000_RXCW_NC 0x04000000 /* Receive config no carrier */ +#define E1000_RXCW_IV 0x08000000 /* Receive config invalid */ +#define E1000_RXCW_CC 0x10000000 /* Receive config change */ +#define E1000_RXCW_C 0x20000000 /* Receive config */ +#define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */ +#define E1000_RXCW_ANC 0x80000000 /* Auto-neg complete */ /* Transmit Control */ -#define E1000_TCTL_RST 0x00000001 /* software reset */ -#define E1000_TCTL_EN 0x00000002 /* enable tx */ -#define E1000_TCTL_BCE 0x00000004 /* busy check enable */ -#define E1000_TCTL_PSP 0x00000008 /* pad short packets */ -#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ -#define E1000_TCTL_COLD 0x003ff000 /* collision distance */ -#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */ -#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */ -#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ -#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ -#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ +#define E1000_TCTL_RST 0x00000001 /* software reset */ +#define E1000_TCTL_EN 0x00000002 /* enable tx */ +#define E1000_TCTL_BCE 0x00000004 /* busy check enable */ +#define E1000_TCTL_PSP 0x00000008 /* pad short packets */ +#define E1000_TCTL_CT 0x00000ff0 /* collision threshold */ +#define E1000_TCTL_COLD 0x003ff000 /* collision distance */ +#define E1000_TCTL_SWXOFF 0x00400000 /* SW Xoff transmission */ +#define E1000_TCTL_PBE 0x00800000 /* Packet Burst Enable */ +#define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */ +#define E1000_TCTL_NRTU 0x02000000 /* No Re-transmit on underrun */ +#define E1000_TCTL_MULR 0x10000000 /* Multiple request support */ /* Extended Transmit Control */ -#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */ -#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ - -#define DEFAULT_80003ES2LAN_TCTL_EXT_GCEX 0x00010000 +#define E1000_TCTL_EXT_BST_MASK 0x000003FF /* Backoff Slot Time */ +#define E1000_TCTL_EXT_GCEX_MASK 0x000FFC00 /* Gigabit Carry Extend Padding */ /* Receive Checksum Control */ -#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */ -#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */ -#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */ -#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */ -#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */ -#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */ +#define E1000_RXCSUM_PCSS_MASK 0x000000FF /* Packet Checksum Start */ +#define E1000_RXCSUM_IPOFL 0x00000100 /* IPv4 checksum offload */ +#define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */ +#define E1000_RXCSUM_IPV6OFL 0x00000400 /* IPv6 checksum offload */ +#define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */ +#define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */ /* Multiple Receive Queue Control */ #define E1000_MRQC_ENABLE_MASK 0x00000003 @@ -2042,141 +1953,141 @@ struct e1000_hw { /* Definitions for power management and wakeup registers */ /* Wake Up Control */ -#define E1000_WUC_APME 0x00000001 /* APM Enable */ -#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */ -#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */ -#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */ -#define E1000_WUC_SPM 0x80000000 /* Enable SPM */ +#define E1000_WUC_APME 0x00000001 /* APM Enable */ +#define E1000_WUC_PME_EN 0x00000002 /* PME Enable */ +#define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */ +#define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */ +#define E1000_WUC_SPM 0x80000000 /* Enable SPM */ /* Wake Up Filter Control */ -#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ -#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ -#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ -#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ -#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ -#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ -#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */ -#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */ -#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */ -#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */ -#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */ -#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */ -#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */ -#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */ -#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */ -#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */ +#define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */ +#define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */ +#define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */ +#define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */ +#define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ +#define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */ +#define E1000_WUFC_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Enable */ +#define E1000_WUFC_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Enable */ +#define E1000_WUFC_IGNORE_TCO 0x00008000 /* Ignore WakeOn TCO packets */ +#define E1000_WUFC_FLX0 0x00010000 /* Flexible Filter 0 Enable */ +#define E1000_WUFC_FLX1 0x00020000 /* Flexible Filter 1 Enable */ +#define E1000_WUFC_FLX2 0x00040000 /* Flexible Filter 2 Enable */ +#define E1000_WUFC_FLX3 0x00080000 /* Flexible Filter 3 Enable */ +#define E1000_WUFC_ALL_FILTERS 0x000F00FF /* Mask for all wakeup filters */ +#define E1000_WUFC_FLX_OFFSET 16 /* Offset to the Flexible Filters bits */ +#define E1000_WUFC_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */ /* Wake Up Status */ -#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */ -#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */ -#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */ -#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */ -#define E1000_WUS_BC 0x00000010 /* Broadcast Received */ -#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */ -#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */ -#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */ -#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */ -#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */ -#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */ -#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */ -#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */ +#define E1000_WUS_LNKC 0x00000001 /* Link Status Changed */ +#define E1000_WUS_MAG 0x00000002 /* Magic Packet Received */ +#define E1000_WUS_EX 0x00000004 /* Directed Exact Received */ +#define E1000_WUS_MC 0x00000008 /* Directed Multicast Received */ +#define E1000_WUS_BC 0x00000010 /* Broadcast Received */ +#define E1000_WUS_ARP 0x00000020 /* ARP Request Packet Received */ +#define E1000_WUS_IPV4 0x00000040 /* Directed IPv4 Packet Wakeup Received */ +#define E1000_WUS_IPV6 0x00000080 /* Directed IPv6 Packet Wakeup Received */ +#define E1000_WUS_FLX0 0x00010000 /* Flexible Filter 0 Match */ +#define E1000_WUS_FLX1 0x00020000 /* Flexible Filter 1 Match */ +#define E1000_WUS_FLX2 0x00040000 /* Flexible Filter 2 Match */ +#define E1000_WUS_FLX3 0x00080000 /* Flexible Filter 3 Match */ +#define E1000_WUS_FLX_FILTERS 0x000F0000 /* Mask for the 4 flexible filters */ /* Management Control */ -#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ -#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ -#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */ -#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */ -#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */ -#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */ -#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */ -#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */ -#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ -#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery - * Filtering */ -#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */ -#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */ -#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ -#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */ -#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */ -#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ -#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address - * filtering */ -#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host - * memory */ -#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address - * filtering */ -#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */ -#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */ -#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */ -#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */ -#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */ -#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */ -#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */ -#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */ - -#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */ -#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */ +#define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */ +#define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */ +#define E1000_MANC_R_ON_FORCE 0x00000004 /* Reset on Force TCO - RO */ +#define E1000_MANC_RMCP_EN 0x00000100 /* Enable RCMP 026Fh Filtering */ +#define E1000_MANC_0298_EN 0x00000200 /* Enable RCMP 0298h Filtering */ +#define E1000_MANC_IPV4_EN 0x00000400 /* Enable IPv4 */ +#define E1000_MANC_IPV6_EN 0x00000800 /* Enable IPv6 */ +#define E1000_MANC_SNAP_EN 0x00001000 /* Accept LLC/SNAP */ +#define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */ +#define E1000_MANC_NEIGHBOR_EN 0x00004000 /* Enable Neighbor Discovery + * Filtering */ +#define E1000_MANC_ARP_RES_EN 0x00008000 /* Enable ARP response Filtering */ +#define E1000_MANC_TCO_RESET 0x00010000 /* TCO Reset Occurred */ +#define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */ +#define E1000_MANC_REPORT_STATUS 0x00040000 /* Status Reporting Enabled */ +#define E1000_MANC_RCV_ALL 0x00080000 /* Receive All Enabled */ +#define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */ +#define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000 /* Enable MAC address + * filtering */ +#define E1000_MANC_EN_MNG2HOST 0x00200000 /* Enable MNG packets to host + * memory */ +#define E1000_MANC_EN_IP_ADDR_FILTER 0x00400000 /* Enable IP address + * filtering */ +#define E1000_MANC_EN_XSUM_FILTER 0x00800000 /* Enable checksum filtering */ +#define E1000_MANC_BR_EN 0x01000000 /* Enable broadcast filtering */ +#define E1000_MANC_SMB_REQ 0x01000000 /* SMBus Request */ +#define E1000_MANC_SMB_GNT 0x02000000 /* SMBus Grant */ +#define E1000_MANC_SMB_CLK_IN 0x04000000 /* SMBus Clock In */ +#define E1000_MANC_SMB_DATA_IN 0x08000000 /* SMBus Data In */ +#define E1000_MANC_SMB_DATA_OUT 0x10000000 /* SMBus Data Out */ +#define E1000_MANC_SMB_CLK_OUT 0x20000000 /* SMBus Clock Out */ + +#define E1000_MANC_SMB_DATA_OUT_SHIFT 28 /* SMBus Data Out Shift */ +#define E1000_MANC_SMB_CLK_OUT_SHIFT 29 /* SMBus Clock Out Shift */ /* SW Semaphore Register */ -#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ -#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ -#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */ -#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */ +#define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */ +#define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */ +#define E1000_SWSM_WMNG 0x00000004 /* Wake MNG Clock */ +#define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */ /* FW Semaphore Register */ -#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */ +#define E1000_FWSM_MODE_MASK 0x0000000E /* FW mode */ #define E1000_FWSM_MODE_SHIFT 1 -#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */ +#define E1000_FWSM_FW_VALID 0x00008000 /* FW established a valid mode */ -#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */ -#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */ -#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */ +#define E1000_FWSM_RSPCIPHY 0x00000040 /* Reset PHY on PCI reset */ +#define E1000_FWSM_DISSW 0x10000000 /* FW disable SW Write Access */ +#define E1000_FWSM_SKUSEL_MASK 0x60000000 /* LAN SKU select */ #define E1000_FWSM_SKUEL_SHIFT 29 -#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */ -#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */ -#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */ -#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */ +#define E1000_FWSM_SKUSEL_EMB 0x0 /* Embedded SKU */ +#define E1000_FWSM_SKUSEL_CONS 0x1 /* Consumer SKU */ +#define E1000_FWSM_SKUSEL_PERF_100 0x2 /* Perf & Corp 10/100 SKU */ +#define E1000_FWSM_SKUSEL_PERF_GBE 0x3 /* Perf & Copr GbE SKU */ /* FFLT Debug Register */ -#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */ +#define E1000_FFLT_DBG_INVC 0x00100000 /* Invalid /C/ code handling */ typedef enum { - e1000_mng_mode_none = 0, - e1000_mng_mode_asf, - e1000_mng_mode_pt, - e1000_mng_mode_ipmi, - e1000_mng_mode_host_interface_only + e1000_mng_mode_none = 0, + e1000_mng_mode_asf, + e1000_mng_mode_pt, + e1000_mng_mode_ipmi, + e1000_mng_mode_host_interface_only } e1000_mng_mode; -/* Host Inteface Control Register */ -#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */ -#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done - * to put command in RAM */ -#define E1000_HICR_SV 0x00000004 /* Status Validity */ -#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */ +/* Host Interface Control Register */ +#define E1000_HICR_EN 0x00000001 /* Enable Bit - RO */ +#define E1000_HICR_C 0x00000002 /* Driver sets this bit when done + * to put command in RAM */ +#define E1000_HICR_SV 0x00000004 /* Status Validity */ +#define E1000_HICR_FWR 0x00000080 /* FW reset. Set by the Host */ /* Host Interface Command Interface - Address range 0x8800-0x8EFF */ -#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */ -#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */ -#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */ -#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */ +#define E1000_HI_MAX_DATA_LENGTH 252 /* Host Interface data length */ +#define E1000_HI_MAX_BLOCK_BYTE_LENGTH 1792 /* Number of bytes in range */ +#define E1000_HI_MAX_BLOCK_DWORD_LENGTH 448 /* Number of dwords in range */ +#define E1000_HI_COMMAND_TIMEOUT 500 /* Time in ms to process HI command */ struct e1000_host_command_header { - u8 command_id; - u8 command_length; - u8 command_options; /* I/F bits for command, status for return */ - u8 checksum; + u8 command_id; + u8 command_length; + u8 command_options; /* I/F bits for command, status for return */ + u8 checksum; }; struct e1000_host_command_info { - struct e1000_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */ - u8 command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */ + struct e1000_host_command_header command_header; /* Command Head/Command Result Head has 4 bytes */ + u8 command_data[E1000_HI_MAX_DATA_LENGTH]; /* Command data can length 0..252 */ }; /* Host SMB register #0 */ -#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */ -#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */ -#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */ -#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */ +#define E1000_HSMC0R_CLKIN 0x00000001 /* SMB Clock in */ +#define E1000_HSMC0R_DATAIN 0x00000002 /* SMB Data in */ +#define E1000_HSMC0R_DATAOUT 0x00000004 /* SMB Data out */ +#define E1000_HSMC0R_CLKOUT 0x00000008 /* SMB Clock out */ /* Host SMB register #1 */ #define E1000_HSMC1R_CLKIN E1000_HSMC0R_CLKIN @@ -2185,10 +2096,10 @@ struct e1000_host_command_info { #define E1000_HSMC1R_CLKOUT E1000_HSMC0R_CLKOUT /* FW Status Register */ -#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */ +#define E1000_FWSTS_FWS_MASK 0x000000FF /* FW Status */ /* Wake Up Packet Length */ -#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */ +#define E1000_WUPL_LENGTH_MASK 0x0FFF /* Only the lower 12 bits are valid */ #define E1000_MDALIGN 4096 @@ -2242,24 +2153,24 @@ struct e1000_host_command_info { #define PCI_EX_LINK_WIDTH_SHIFT 4 /* EEPROM Commands - Microwire */ -#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */ -#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */ -#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */ -#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */ -#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erast/write disable */ +#define EEPROM_READ_OPCODE_MICROWIRE 0x6 /* EEPROM read opcode */ +#define EEPROM_WRITE_OPCODE_MICROWIRE 0x5 /* EEPROM write opcode */ +#define EEPROM_ERASE_OPCODE_MICROWIRE 0x7 /* EEPROM erase opcode */ +#define EEPROM_EWEN_OPCODE_MICROWIRE 0x13 /* EEPROM erase/write enable */ +#define EEPROM_EWDS_OPCODE_MICROWIRE 0x10 /* EEPROM erase/write disable */ /* EEPROM Commands - SPI */ -#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */ -#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */ -#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */ -#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */ -#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */ -#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */ -#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */ -#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */ -#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */ -#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */ -#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */ +#define EEPROM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */ +#define EEPROM_READ_OPCODE_SPI 0x03 /* EEPROM read opcode */ +#define EEPROM_WRITE_OPCODE_SPI 0x02 /* EEPROM write opcode */ +#define EEPROM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */ +#define EEPROM_WREN_OPCODE_SPI 0x06 /* EEPROM set Write Enable latch */ +#define EEPROM_WRDI_OPCODE_SPI 0x04 /* EEPROM reset Write Enable latch */ +#define EEPROM_RDSR_OPCODE_SPI 0x05 /* EEPROM read Status register */ +#define EEPROM_WRSR_OPCODE_SPI 0x01 /* EEPROM write Status register */ +#define EEPROM_ERASE4K_OPCODE_SPI 0x20 /* EEPROM ERASE 4KB */ +#define EEPROM_ERASE64K_OPCODE_SPI 0xD8 /* EEPROM ERASE 64KB */ +#define EEPROM_ERASE256_OPCODE_SPI 0xDB /* EEPROM ERASE 256B */ /* EEPROM Size definitions */ #define EEPROM_WORD_SIZE_SHIFT 6 @@ -2270,7 +2181,7 @@ struct e1000_host_command_info { #define EEPROM_COMPAT 0x0003 #define EEPROM_ID_LED_SETTINGS 0x0004 #define EEPROM_VERSION 0x0005 -#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */ +#define EEPROM_SERDES_AMPLITUDE 0x0006 /* For SERDES output amplitude adjustment. */ #define EEPROM_PHY_CLASS_WORD 0x0007 #define EEPROM_INIT_CONTROL1_REG 0x000A #define EEPROM_INIT_CONTROL2_REG 0x000F @@ -2283,22 +2194,16 @@ struct e1000_host_command_info { #define EEPROM_FLASH_VERSION 0x0032 #define EEPROM_CHECKSUM_REG 0x003F -#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */ -#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */ +#define E1000_EEPROM_CFG_DONE 0x00040000 /* MNG config cycle done */ +#define E1000_EEPROM_CFG_DONE_PORT_1 0x00080000 /* ...for second port */ /* Word definitions for ID LED Settings */ #define ID_LED_RESERVED_0000 0x0000 #define ID_LED_RESERVED_FFFF 0xFFFF -#define ID_LED_RESERVED_82573 0xF746 -#define ID_LED_DEFAULT_82573 0x1811 #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \ (ID_LED_OFF1_OFF2 << 8) | \ (ID_LED_DEF1_DEF2 << 4) | \ (ID_LED_DEF1_DEF2)) -#define ID_LED_DEFAULT_ICH8LAN ((ID_LED_DEF1_DEF2 << 12) | \ - (ID_LED_DEF1_OFF2 << 8) | \ - (ID_LED_DEF1_ON2 << 4) | \ - (ID_LED_DEF1_DEF2)) #define ID_LED_DEF1_DEF2 0x1 #define ID_LED_DEF1_ON2 0x2 #define ID_LED_DEF1_OFF2 0x3 @@ -2313,7 +2218,6 @@ struct e1000_host_command_info { #define IGP_ACTIVITY_LED_ENABLE 0x0300 #define IGP_LED3_MODE 0x07000000 - /* Mask bits for SERDES amplitude adjustment in Word 6 of the EEPROM */ #define EEPROM_SERDES_AMPLITUDE_MASK 0x000F @@ -2384,11 +2288,8 @@ struct e1000_host_command_info { #define DEFAULT_82542_TIPG_IPGR2 10 #define DEFAULT_82543_TIPG_IPGR2 6 -#define DEFAULT_80003ES2LAN_TIPG_IPGR2 7 #define E1000_TIPG_IPGR2_SHIFT 20 -#define DEFAULT_80003ES2LAN_TIPG_IPGT_10_100 0x00000009 -#define DEFAULT_80003ES2LAN_TIPG_IPGT_1000 0x00000008 #define E1000_TXDMAC_DPP 0x00000001 /* Adaptive IFS defines */ @@ -2421,9 +2322,9 @@ struct e1000_host_command_info { #define E1000_EXTCNF_CTRL_SWFLAG 0x00000020 /* PBA constants */ -#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */ -#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */ -#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */ +#define E1000_PBA_8K 0x0008 /* 8KB, default Rx allocation */ +#define E1000_PBA_12K 0x000C /* 12KB, default Rx allocation */ +#define E1000_PBA_16K 0x0010 /* 16KB, default TX allocation */ #define E1000_PBA_20K 0x0014 #define E1000_PBA_22K 0x0016 #define E1000_PBA_24K 0x0018 @@ -2432,7 +2333,7 @@ struct e1000_host_command_info { #define E1000_PBA_34K 0x0022 #define E1000_PBA_38K 0x0026 #define E1000_PBA_40K 0x0028 -#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */ +#define E1000_PBA_48K 0x0030 /* 48KB, default RX allocation */ #define E1000_PBS_16K E1000_PBA_16K @@ -2442,9 +2343,9 @@ struct e1000_host_command_info { #define FLOW_CONTROL_TYPE 0x8808 /* The historical defaults for the flow control values are given below. */ -#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */ -#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */ -#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */ +#define FC_DEFAULT_HI_THRESH (0x8000) /* 32KB */ +#define FC_DEFAULT_LO_THRESH (0x4000) /* 16KB */ +#define FC_DEFAULT_TX_TIMER (0x100) /* ~130 us */ /* PCIX Config space */ #define PCIX_COMMAND_REGISTER 0xE6 @@ -2458,7 +2359,6 @@ struct e1000_host_command_info { #define PCIX_STATUS_HI_MMRBC_4K 0x3 #define PCIX_STATUS_HI_MMRBC_2K 0x2 - /* Number of bits required to shift right the "pause" bits from the * EEPROM (bits 13:12) to the "pause" (bits 8:7) field in the TXCW register. */ @@ -2479,14 +2379,11 @@ struct e1000_host_command_info { */ #define ILOS_SHIFT 3 - #define RECEIVE_BUFFER_ALIGN_SIZE (256) /* Number of milliseconds we wait for auto-negotiation to complete */ #define LINK_UP_TIMEOUT 500 -/* Number of 100 microseconds we wait for PCI Express master disable */ -#define MASTER_DISABLE_TIMEOUT 800 /* Number of milliseconds we wait for Eeprom auto read bit done after MAC reset */ #define AUTO_READ_DONE_TIMEOUT 10 /* Number of milliseconds we wait for PHY configuration done after MAC reset */ @@ -2534,7 +2431,6 @@ struct e1000_host_command_info { (((length) > (adapter)->min_frame_size) && \ ((length) <= ((adapter)->max_frame_size + VLAN_TAG_SIZE + 1))))) - /* Structures, enums, and macros for the PHY */ /* Bit definitions for the Management Data IO (MDIO) and Management Data @@ -2551,49 +2447,49 @@ struct e1000_host_command_info { /* PHY 1000 MII Register/Bit Definitions */ /* PHY Registers defined by IEEE */ -#define PHY_CTRL 0x00 /* Control Register */ -#define PHY_STATUS 0x01 /* Status Regiser */ -#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */ -#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */ -#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */ -#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */ -#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */ -#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */ -#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */ -#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */ -#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */ -#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */ - -#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ -#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */ +#define PHY_CTRL 0x00 /* Control Register */ +#define PHY_STATUS 0x01 /* Status Register */ +#define PHY_ID1 0x02 /* Phy Id Reg (word 1) */ +#define PHY_ID2 0x03 /* Phy Id Reg (word 2) */ +#define PHY_AUTONEG_ADV 0x04 /* Autoneg Advertisement */ +#define PHY_LP_ABILITY 0x05 /* Link Partner Ability (Base Page) */ +#define PHY_AUTONEG_EXP 0x06 /* Autoneg Expansion Reg */ +#define PHY_NEXT_PAGE_TX 0x07 /* Next Page TX */ +#define PHY_LP_NEXT_PAGE 0x08 /* Link Partner Next Page */ +#define PHY_1000T_CTRL 0x09 /* 1000Base-T Control Reg */ +#define PHY_1000T_STATUS 0x0A /* 1000Base-T Status Reg */ +#define PHY_EXT_STATUS 0x0F /* Extended Status Reg */ + +#define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */ +#define MAX_PHY_MULTI_PAGE_REG 0xF /* Registers equal on all pages */ /* M88E1000 Specific Registers */ -#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */ -#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */ -#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */ -#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */ -#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */ -#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */ - -#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */ -#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */ -#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */ -#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */ -#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */ +#define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */ +#define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */ +#define M88E1000_INT_ENABLE 0x12 /* Interrupt Enable Register */ +#define M88E1000_INT_STATUS 0x13 /* Interrupt Status Register */ +#define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */ +#define M88E1000_RX_ERR_CNTR 0x15 /* Receive Error Counter */ + +#define M88E1000_PHY_EXT_CTRL 0x1A /* PHY extend control register */ +#define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */ +#define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */ +#define M88E1000_PHY_VCO_REG_BIT8 0x100 /* Bits 8 & 11 are adjusted for */ +#define M88E1000_PHY_VCO_REG_BIT11 0x800 /* improved BER performance */ #define IGP01E1000_IEEE_REGS_PAGE 0x0000 #define IGP01E1000_IEEE_RESTART_AUTONEG 0x3300 #define IGP01E1000_IEEE_FORCE_GIGA 0x0140 /* IGP01E1000 Specific Registers */ -#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */ -#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */ -#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */ -#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */ -#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */ -#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */ +#define IGP01E1000_PHY_PORT_CONFIG 0x10 /* PHY Specific Port Config Register */ +#define IGP01E1000_PHY_PORT_STATUS 0x11 /* PHY Specific Status Register */ +#define IGP01E1000_PHY_PORT_CTRL 0x12 /* PHY Specific Control Register */ +#define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health Register */ +#define IGP01E1000_GMII_FIFO 0x14 /* GMII FIFO Register */ +#define IGP01E1000_PHY_CHANNEL_QUALITY 0x15 /* PHY Channel Quality Register */ #define IGP02E1000_PHY_POWER_MGMT 0x19 -#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */ +#define IGP01E1000_PHY_PAGE_SELECT 0x1F /* PHY Page Select Core Register */ /* IGP01E1000 AGC Registers - stores the cable length values*/ #define IGP01E1000_PHY_AGC_A 0x1172 @@ -2636,192 +2532,119 @@ struct e1000_host_command_info { #define IGP01E1000_ANALOG_REGS_PAGE 0x20C0 -/* Bits... - * 15-5: page - * 4-0: register offset - */ -#define GG82563_PAGE_SHIFT 5 -#define GG82563_REG(page, reg) \ - (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) -#define GG82563_MIN_ALT_REG 30 - -/* GG82563 Specific Registers */ -#define GG82563_PHY_SPEC_CTRL \ - GG82563_REG(0, 16) /* PHY Specific Control */ -#define GG82563_PHY_SPEC_STATUS \ - GG82563_REG(0, 17) /* PHY Specific Status */ -#define GG82563_PHY_INT_ENABLE \ - GG82563_REG(0, 18) /* Interrupt Enable */ -#define GG82563_PHY_SPEC_STATUS_2 \ - GG82563_REG(0, 19) /* PHY Specific Status 2 */ -#define GG82563_PHY_RX_ERR_CNTR \ - GG82563_REG(0, 21) /* Receive Error Counter */ -#define GG82563_PHY_PAGE_SELECT \ - GG82563_REG(0, 22) /* Page Select */ -#define GG82563_PHY_SPEC_CTRL_2 \ - GG82563_REG(0, 26) /* PHY Specific Control 2 */ -#define GG82563_PHY_PAGE_SELECT_ALT \ - GG82563_REG(0, 29) /* Alternate Page Select */ -#define GG82563_PHY_TEST_CLK_CTRL \ - GG82563_REG(0, 30) /* Test Clock Control (use reg. 29 to select) */ - -#define GG82563_PHY_MAC_SPEC_CTRL \ - GG82563_REG(2, 21) /* MAC Specific Control Register */ -#define GG82563_PHY_MAC_SPEC_CTRL_2 \ - GG82563_REG(2, 26) /* MAC Specific Control 2 */ - -#define GG82563_PHY_DSP_DISTANCE \ - GG82563_REG(5, 26) /* DSP Distance */ - -/* Page 193 - Port Control Registers */ -#define GG82563_PHY_KMRN_MODE_CTRL \ - GG82563_REG(193, 16) /* Kumeran Mode Control */ -#define GG82563_PHY_PORT_RESET \ - GG82563_REG(193, 17) /* Port Reset */ -#define GG82563_PHY_REVISION_ID \ - GG82563_REG(193, 18) /* Revision ID */ -#define GG82563_PHY_DEVICE_ID \ - GG82563_REG(193, 19) /* Device ID */ -#define GG82563_PHY_PWR_MGMT_CTRL \ - GG82563_REG(193, 20) /* Power Management Control */ -#define GG82563_PHY_RATE_ADAPT_CTRL \ - GG82563_REG(193, 25) /* Rate Adaptation Control */ - -/* Page 194 - KMRN Registers */ -#define GG82563_PHY_KMRN_FIFO_CTRL_STAT \ - GG82563_REG(194, 16) /* FIFO's Control/Status */ -#define GG82563_PHY_KMRN_CTRL \ - GG82563_REG(194, 17) /* Control */ -#define GG82563_PHY_INBAND_CTRL \ - GG82563_REG(194, 18) /* Inband Control */ -#define GG82563_PHY_KMRN_DIAGNOSTIC \ - GG82563_REG(194, 19) /* Diagnostic */ -#define GG82563_PHY_ACK_TIMEOUTS \ - GG82563_REG(194, 20) /* Acknowledge Timeouts */ -#define GG82563_PHY_ADV_ABILITY \ - GG82563_REG(194, 21) /* Advertised Ability */ -#define GG82563_PHY_LINK_PARTNER_ADV_ABILITY \ - GG82563_REG(194, 23) /* Link Partner Advertised Ability */ -#define GG82563_PHY_ADV_NEXT_PAGE \ - GG82563_REG(194, 24) /* Advertised Next Page */ -#define GG82563_PHY_LINK_PARTNER_ADV_NEXT_PAGE \ - GG82563_REG(194, 25) /* Link Partner Advertised Next page */ -#define GG82563_PHY_KMRN_MISC \ - GG82563_REG(194, 26) /* Misc. */ - /* PHY Control Register */ -#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ -#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ -#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ -#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ -#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ -#define MII_CR_POWER_DOWN 0x0800 /* Power down */ -#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ -#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */ -#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ -#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ +#define MII_CR_SPEED_SELECT_MSB 0x0040 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_COLL_TEST_ENABLE 0x0080 /* Collision test enable */ +#define MII_CR_FULL_DUPLEX 0x0100 /* FDX =1, half duplex =0 */ +#define MII_CR_RESTART_AUTO_NEG 0x0200 /* Restart auto negotiation */ +#define MII_CR_ISOLATE 0x0400 /* Isolate PHY from MII */ +#define MII_CR_POWER_DOWN 0x0800 /* Power down */ +#define MII_CR_AUTO_NEG_EN 0x1000 /* Auto Neg Enable */ +#define MII_CR_SPEED_SELECT_LSB 0x2000 /* bits 6,13: 10=1000, 01=100, 00=10 */ +#define MII_CR_LOOPBACK 0x4000 /* 0 = normal, 1 = loopback */ +#define MII_CR_RESET 0x8000 /* 0 = normal, 1 = PHY reset */ /* PHY Status Register */ -#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */ -#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ -#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ -#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ -#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ -#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ -#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ -#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */ -#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ -#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ -#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ -#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ -#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ -#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ -#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ +#define MII_SR_EXTENDED_CAPS 0x0001 /* Extended register capabilities */ +#define MII_SR_JABBER_DETECT 0x0002 /* Jabber Detected */ +#define MII_SR_LINK_STATUS 0x0004 /* Link Status 1 = link */ +#define MII_SR_AUTONEG_CAPS 0x0008 /* Auto Neg Capable */ +#define MII_SR_REMOTE_FAULT 0x0010 /* Remote Fault Detect */ +#define MII_SR_AUTONEG_COMPLETE 0x0020 /* Auto Neg Complete */ +#define MII_SR_PREAMBLE_SUPPRESS 0x0040 /* Preamble may be suppressed */ +#define MII_SR_EXTENDED_STATUS 0x0100 /* Ext. status info in Reg 0x0F */ +#define MII_SR_100T2_HD_CAPS 0x0200 /* 100T2 Half Duplex Capable */ +#define MII_SR_100T2_FD_CAPS 0x0400 /* 100T2 Full Duplex Capable */ +#define MII_SR_10T_HD_CAPS 0x0800 /* 10T Half Duplex Capable */ +#define MII_SR_10T_FD_CAPS 0x1000 /* 10T Full Duplex Capable */ +#define MII_SR_100X_HD_CAPS 0x2000 /* 100X Half Duplex Capable */ +#define MII_SR_100X_FD_CAPS 0x4000 /* 100X Full Duplex Capable */ +#define MII_SR_100T4_CAPS 0x8000 /* 100T4 Capable */ /* Autoneg Advertisement Register */ -#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */ -#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ -#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ -#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ -#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ -#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ -#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */ -#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */ -#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ -#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */ +#define NWAY_AR_SELECTOR_FIELD 0x0001 /* indicates IEEE 802.3 CSMA/CD */ +#define NWAY_AR_10T_HD_CAPS 0x0020 /* 10T Half Duplex Capable */ +#define NWAY_AR_10T_FD_CAPS 0x0040 /* 10T Full Duplex Capable */ +#define NWAY_AR_100TX_HD_CAPS 0x0080 /* 100TX Half Duplex Capable */ +#define NWAY_AR_100TX_FD_CAPS 0x0100 /* 100TX Full Duplex Capable */ +#define NWAY_AR_100T4_CAPS 0x0200 /* 100T4 Capable */ +#define NWAY_AR_PAUSE 0x0400 /* Pause operation desired */ +#define NWAY_AR_ASM_DIR 0x0800 /* Asymmetric Pause Direction bit */ +#define NWAY_AR_REMOTE_FAULT 0x2000 /* Remote Fault detected */ +#define NWAY_AR_NEXT_PAGE 0x8000 /* Next Page ability supported */ /* Link Partner Ability Register (Base Page) */ -#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */ -#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */ -#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */ -#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */ -#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */ -#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */ -#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */ -#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */ -#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */ -#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */ -#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */ +#define NWAY_LPAR_SELECTOR_FIELD 0x0000 /* LP protocol selector field */ +#define NWAY_LPAR_10T_HD_CAPS 0x0020 /* LP is 10T Half Duplex Capable */ +#define NWAY_LPAR_10T_FD_CAPS 0x0040 /* LP is 10T Full Duplex Capable */ +#define NWAY_LPAR_100TX_HD_CAPS 0x0080 /* LP is 100TX Half Duplex Capable */ +#define NWAY_LPAR_100TX_FD_CAPS 0x0100 /* LP is 100TX Full Duplex Capable */ +#define NWAY_LPAR_100T4_CAPS 0x0200 /* LP is 100T4 Capable */ +#define NWAY_LPAR_PAUSE 0x0400 /* LP Pause operation desired */ +#define NWAY_LPAR_ASM_DIR 0x0800 /* LP Asymmetric Pause Direction bit */ +#define NWAY_LPAR_REMOTE_FAULT 0x2000 /* LP has detected Remote Fault */ +#define NWAY_LPAR_ACKNOWLEDGE 0x4000 /* LP has rx'd link code word */ +#define NWAY_LPAR_NEXT_PAGE 0x8000 /* Next Page ability supported */ /* Autoneg Expansion Register */ -#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */ -#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */ -#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */ -#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */ -#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */ +#define NWAY_ER_LP_NWAY_CAPS 0x0001 /* LP has Auto Neg Capability */ +#define NWAY_ER_PAGE_RXD 0x0002 /* LP is 10T Half Duplex Capable */ +#define NWAY_ER_NEXT_PAGE_CAPS 0x0004 /* LP is 10T Full Duplex Capable */ +#define NWAY_ER_LP_NEXT_PAGE_CAPS 0x0008 /* LP is 100TX Half Duplex Capable */ +#define NWAY_ER_PAR_DETECT_FAULT 0x0010 /* LP is 100TX Full Duplex Capable */ /* Next Page TX Register */ -#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ -#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges - * of different NP - */ -#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg - * 0 = cannot comply with msg - */ -#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ -#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow - * 0 = sending last NP - */ +#define NPTX_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ +#define NPTX_TOGGLE 0x0800 /* Toggles between exchanges + * of different NP + */ +#define NPTX_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg + * 0 = cannot comply with msg + */ +#define NPTX_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ +#define NPTX_NEXT_PAGE 0x8000 /* 1 = addition NP will follow + * 0 = sending last NP + */ /* Link Partner Next Page Register */ -#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ -#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges - * of different NP - */ -#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg - * 0 = cannot comply with msg - */ -#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ -#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */ -#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow - * 0 = sending last NP - */ +#define LP_RNPR_MSG_CODE_FIELD 0x0001 /* NP msg code or unformatted data */ +#define LP_RNPR_TOGGLE 0x0800 /* Toggles between exchanges + * of different NP + */ +#define LP_RNPR_ACKNOWLDGE2 0x1000 /* 1 = will comply with msg + * 0 = cannot comply with msg + */ +#define LP_RNPR_MSG_PAGE 0x2000 /* formatted(1)/unformatted(0) pg */ +#define LP_RNPR_ACKNOWLDGE 0x4000 /* 1 = ACK / 0 = NO ACK */ +#define LP_RNPR_NEXT_PAGE 0x8000 /* 1 = addition NP will follow + * 0 = sending last NP + */ /* 1000BASE-T Control Register */ -#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */ -#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */ -#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */ -#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */ - /* 0=DTE device */ -#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */ - /* 0=Configure PHY as Slave */ -#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */ - /* 0=Automatic Master/Slave config */ -#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ -#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ -#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */ -#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */ -#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */ +#define CR_1000T_ASYM_PAUSE 0x0080 /* Advertise asymmetric pause bit */ +#define CR_1000T_HD_CAPS 0x0100 /* Advertise 1000T HD capability */ +#define CR_1000T_FD_CAPS 0x0200 /* Advertise 1000T FD capability */ +#define CR_1000T_REPEATER_DTE 0x0400 /* 1=Repeater/switch device port */ + /* 0=DTE device */ +#define CR_1000T_MS_VALUE 0x0800 /* 1=Configure PHY as Master */ + /* 0=Configure PHY as Slave */ +#define CR_1000T_MS_ENABLE 0x1000 /* 1=Master/Slave manual config value */ + /* 0=Automatic Master/Slave config */ +#define CR_1000T_TEST_MODE_NORMAL 0x0000 /* Normal Operation */ +#define CR_1000T_TEST_MODE_1 0x2000 /* Transmit Waveform test */ +#define CR_1000T_TEST_MODE_2 0x4000 /* Master Transmit Jitter test */ +#define CR_1000T_TEST_MODE_3 0x6000 /* Slave Transmit Jitter test */ +#define CR_1000T_TEST_MODE_4 0x8000 /* Transmitter Distortion test */ /* 1000BASE-T Status Register */ -#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */ -#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */ -#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ -#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ -#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ -#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ -#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */ -#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */ +#define SR_1000T_IDLE_ERROR_CNT 0x00FF /* Num idle errors since last read */ +#define SR_1000T_ASYM_PAUSE_DIR 0x0100 /* LP asymmetric pause direction bit */ +#define SR_1000T_LP_HD_CAPS 0x0400 /* LP is 1000T HD capable */ +#define SR_1000T_LP_FD_CAPS 0x0800 /* LP is 1000T FD capable */ +#define SR_1000T_REMOTE_RX_STATUS 0x1000 /* Remote receiver OK */ +#define SR_1000T_LOCAL_RX_STATUS 0x2000 /* Local receiver OK */ +#define SR_1000T_MS_CONFIG_RES 0x4000 /* 1=Local TX is Master, 0=Slave */ +#define SR_1000T_MS_CONFIG_FAULT 0x8000 /* Master/Slave config fault */ #define SR_1000T_REMOTE_RX_STATUS_SHIFT 12 #define SR_1000T_LOCAL_RX_STATUS_SHIFT 13 #define SR_1000T_PHY_EXCESSIVE_IDLE_ERR_COUNT 5 @@ -2829,64 +2652,64 @@ struct e1000_host_command_info { #define FFE_IDLE_ERR_COUNT_TIMEOUT_100 100 /* Extended Status Register */ -#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */ -#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */ -#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */ -#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */ +#define IEEE_ESR_1000T_HD_CAPS 0x1000 /* 1000T HD capable */ +#define IEEE_ESR_1000T_FD_CAPS 0x2000 /* 1000T FD capable */ +#define IEEE_ESR_1000X_HD_CAPS 0x4000 /* 1000X HD capable */ +#define IEEE_ESR_1000X_FD_CAPS 0x8000 /* 1000X FD capable */ -#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */ -#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */ +#define PHY_TX_POLARITY_MASK 0x0100 /* register 10h bit 8 (polarity bit) */ +#define PHY_TX_NORMAL_POLARITY 0 /* register 10h bit 8 (normal polarity) */ -#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */ - /* (0=enable, 1=disable) */ +#define AUTO_POLARITY_DISABLE 0x0010 /* register 11h bit 4 */ + /* (0=enable, 1=disable) */ /* M88E1000 PHY Specific Control Register */ -#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */ -#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */ -#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */ -#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low, - * 0=CLK125 toggling - */ -#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */ - /* Manual MDI configuration */ -#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ -#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover, - * 100BASE-TX/10BASE-T: - * MDI Mode - */ -#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled - * all speeds. - */ +#define M88E1000_PSCR_JABBER_DISABLE 0x0001 /* 1=Jabber Function disabled */ +#define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */ +#define M88E1000_PSCR_SQE_TEST 0x0004 /* 1=SQE Test enabled */ +#define M88E1000_PSCR_CLK125_DISABLE 0x0010 /* 1=CLK125 low, + * 0=CLK125 toggling + */ +#define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */ + /* Manual MDI configuration */ +#define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */ +#define M88E1000_PSCR_AUTO_X_1000T 0x0040 /* 1000BASE-T: Auto crossover, + * 100BASE-TX/10BASE-T: + * MDI Mode + */ +#define M88E1000_PSCR_AUTO_X_MODE 0x0060 /* Auto crossover enabled + * all speeds. + */ #define M88E1000_PSCR_10BT_EXT_DIST_ENABLE 0x0080 - /* 1=Enable Extended 10BASE-T distance - * (Lower 10BASE-T RX Threshold) - * 0=Normal 10BASE-T RX Threshold */ + /* 1=Enable Extended 10BASE-T distance + * (Lower 10BASE-T RX Threshold) + * 0=Normal 10BASE-T RX Threshold */ #define M88E1000_PSCR_MII_5BIT_ENABLE 0x0100 - /* 1=5-Bit interface in 100BASE-TX - * 0=MII interface in 100BASE-TX */ -#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */ -#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */ -#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ + /* 1=5-Bit interface in 100BASE-TX + * 0=MII interface in 100BASE-TX */ +#define M88E1000_PSCR_SCRAMBLER_DISABLE 0x0200 /* 1=Scrambler disable */ +#define M88E1000_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force link good */ +#define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */ #define M88E1000_PSCR_POLARITY_REVERSAL_SHIFT 1 #define M88E1000_PSCR_AUTO_X_MODE_SHIFT 5 #define M88E1000_PSCR_10BT_EXT_DIST_ENABLE_SHIFT 7 /* M88E1000 PHY Specific Status Register */ -#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */ -#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */ -#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */ -#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */ -#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M; - * 3=110-140M;4=>140M */ -#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */ -#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ -#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */ -#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */ -#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ -#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */ -#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */ -#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ +#define M88E1000_PSSR_JABBER 0x0001 /* 1=Jabber */ +#define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */ +#define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */ +#define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */ +#define M88E1000_PSSR_CABLE_LENGTH 0x0380 /* 0=<50M;1=50-80M;2=80-110M; + * 3=110-140M;4=>140M */ +#define M88E1000_PSSR_LINK 0x0400 /* 1=Link up, 0=Link down */ +#define M88E1000_PSSR_SPD_DPLX_RESOLVED 0x0800 /* 1=Speed & Duplex resolved */ +#define M88E1000_PSSR_PAGE_RCVD 0x1000 /* 1=Page received */ +#define M88E1000_PSSR_DPLX 0x2000 /* 1=Duplex 0=Half Duplex */ +#define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */ +#define M88E1000_PSSR_10MBS 0x0000 /* 00=10Mbs */ +#define M88E1000_PSSR_100MBS 0x4000 /* 01=100Mbs */ +#define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */ #define M88E1000_PSSR_REV_POLARITY_SHIFT 1 #define M88E1000_PSSR_DOWNSHIFT_SHIFT 5 @@ -2894,12 +2717,12 @@ struct e1000_host_command_info { #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7 /* M88E1000 Extended PHY Specific Control Register */ -#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */ -#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled. - * Will assert lost lock and bring - * link down if idle not seen - * within 1ms in 1000BASE-T - */ +#define M88E1000_EPSCR_FIBER_LOOPBACK 0x4000 /* 1=Fiber loopback */ +#define M88E1000_EPSCR_DOWN_NO_IDLE 0x8000 /* 1=Lost lock detect enabled. + * Will assert lost lock and bring + * link down if idle not seen + * within 1ms in 1000BASE-T + */ /* Number of times we will attempt to autonegotiate before downshifting if we * are the master */ #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00 @@ -2914,9 +2737,9 @@ struct e1000_host_command_info { #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_2X 0x0200 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_3X 0x0300 -#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */ -#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ -#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */ +#define M88E1000_EPSCR_TX_CLK_2_5 0x0060 /* 2.5 MHz TX_CLK */ +#define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */ +#define M88E1000_EPSCR_TX_CLK_0 0x0000 /* NO TX_CLK */ /* M88EC018 Rev 2 specific DownShift settings */ #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 @@ -2938,18 +2761,18 @@ struct e1000_host_command_info { #define IGP01E1000_PSCFR_DISABLE_TRANSMIT 0x2000 /* IGP01E1000 Specific Port Status Register - R/O */ -#define IGP01E1000_PSSR_AUTONEG_FAILED 0x0001 /* RO LH SC */ +#define IGP01E1000_PSSR_AUTONEG_FAILED 0x0001 /* RO LH SC */ #define IGP01E1000_PSSR_POLARITY_REVERSED 0x0002 #define IGP01E1000_PSSR_CABLE_LENGTH 0x007C #define IGP01E1000_PSSR_FULL_DUPLEX 0x0200 #define IGP01E1000_PSSR_LINK_UP 0x0400 #define IGP01E1000_PSSR_MDIX 0x0800 -#define IGP01E1000_PSSR_SPEED_MASK 0xC000 /* speed bits mask */ +#define IGP01E1000_PSSR_SPEED_MASK 0xC000 /* speed bits mask */ #define IGP01E1000_PSSR_SPEED_10MBPS 0x4000 #define IGP01E1000_PSSR_SPEED_100MBPS 0x8000 #define IGP01E1000_PSSR_SPEED_1000MBPS 0xC000 -#define IGP01E1000_PSSR_CABLE_LENGTH_SHIFT 0x0002 /* shift right 2 */ -#define IGP01E1000_PSSR_MDIX_SHIFT 0x000B /* shift right 11 */ +#define IGP01E1000_PSSR_CABLE_LENGTH_SHIFT 0x0002 /* shift right 2 */ +#define IGP01E1000_PSSR_MDIX_SHIFT 0x000B /* shift right 11 */ /* IGP01E1000 Specific Port Control Register - R/W */ #define IGP01E1000_PSCR_TP_LOOPBACK 0x0010 @@ -2957,16 +2780,16 @@ struct e1000_host_command_info { #define IGP01E1000_PSCR_TEN_CRS_SELECT 0x0400 #define IGP01E1000_PSCR_FLIP_CHIP 0x0800 #define IGP01E1000_PSCR_AUTO_MDIX 0x1000 -#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */ +#define IGP01E1000_PSCR_FORCE_MDI_MDIX 0x2000 /* 0-MDI, 1-MDIX */ /* IGP01E1000 Specific Port Link Health Register */ #define IGP01E1000_PLHR_SS_DOWNGRADE 0x8000 #define IGP01E1000_PLHR_GIG_SCRAMBLER_ERROR 0x4000 #define IGP01E1000_PLHR_MASTER_FAULT 0x2000 #define IGP01E1000_PLHR_MASTER_RESOLUTION 0x1000 -#define IGP01E1000_PLHR_GIG_REM_RCVR_NOK 0x0800 /* LH */ -#define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW 0x0400 /* LH */ -#define IGP01E1000_PLHR_DATA_ERR_1 0x0200 /* LH */ +#define IGP01E1000_PLHR_GIG_REM_RCVR_NOK 0x0800 /* LH */ +#define IGP01E1000_PLHR_IDLE_ERROR_CNT_OFLOW 0x0400 /* LH */ +#define IGP01E1000_PLHR_DATA_ERR_1 0x0200 /* LH */ #define IGP01E1000_PLHR_DATA_ERR_0 0x0100 #define IGP01E1000_PLHR_AUTONEG_FAULT 0x0040 #define IGP01E1000_PLHR_AUTONEG_ACTIVE 0x0010 @@ -2981,9 +2804,9 @@ struct e1000_host_command_info { #define IGP01E1000_MSE_CHANNEL_B 0x0F00 #define IGP01E1000_MSE_CHANNEL_A 0xF000 -#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */ -#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */ -#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */ +#define IGP02E1000_PM_SPD 0x0001 /* Smart Power Down */ +#define IGP02E1000_PM_D3_LPLU 0x0004 /* Enable LPLU in non-D0a modes */ +#define IGP02E1000_PM_D0_LPLU 0x0002 /* Enable LPLU in D0a mode */ /* IGP01E1000 DSP reset macros */ #define DSP_RESET_ENABLE 0x0 @@ -2992,8 +2815,8 @@ struct e1000_host_command_info { /* IGP01E1000 & IGP02E1000 AGC Registers */ -#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */ -#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */ +#define IGP01E1000_AGC_LENGTH_SHIFT 7 /* Coarse - 13:11, Fine - 10:7 */ +#define IGP02E1000_AGC_LENGTH_SHIFT 9 /* Coarse - 15:13, Fine - 12:9 */ /* IGP02E1000 AGC Register Length 9-bit mask */ #define IGP02E1000_AGC_LENGTH_MASK 0x7F @@ -3011,9 +2834,9 @@ struct e1000_host_command_info { #define IGP01E1000_PHY_POLARITY_MASK 0x0078 /* IGP01E1000 GMII FIFO Register */ -#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed - * on Link-Up */ -#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */ +#define IGP01E1000_GMII_FLEX_SPD 0x10 /* Enable flexible speed + * on Link-Up */ +#define IGP01E1000_GMII_SPD 0x20 /* Enable SPD */ /* IGP01E1000 Analog Register */ #define IGP01E1000_ANALOG_SPARE_FUSE_STATUS 0x20D1 @@ -3032,114 +2855,6 @@ struct e1000_host_command_info { #define IGP01E1000_ANALOG_FUSE_FINE_1 0x0080 #define IGP01E1000_ANALOG_FUSE_FINE_10 0x0500 -/* GG82563 PHY Specific Status Register (Page 0, Register 16 */ -#define GG82563_PSCR_DISABLE_JABBER 0x0001 /* 1=Disable Jabber */ -#define GG82563_PSCR_POLARITY_REVERSAL_DISABLE 0x0002 /* 1=Polarity Reversal Disabled */ -#define GG82563_PSCR_POWER_DOWN 0x0004 /* 1=Power Down */ -#define GG82563_PSCR_COPPER_TRANSMITER_DISABLE 0x0008 /* 1=Transmitter Disabled */ -#define GG82563_PSCR_CROSSOVER_MODE_MASK 0x0060 -#define GG82563_PSCR_CROSSOVER_MODE_MDI 0x0000 /* 00=Manual MDI configuration */ -#define GG82563_PSCR_CROSSOVER_MODE_MDIX 0x0020 /* 01=Manual MDIX configuration */ -#define GG82563_PSCR_CROSSOVER_MODE_AUTO 0x0060 /* 11=Automatic crossover */ -#define GG82563_PSCR_ENALBE_EXTENDED_DISTANCE 0x0080 /* 1=Enable Extended Distance */ -#define GG82563_PSCR_ENERGY_DETECT_MASK 0x0300 -#define GG82563_PSCR_ENERGY_DETECT_OFF 0x0000 /* 00,01=Off */ -#define GG82563_PSCR_ENERGY_DETECT_RX 0x0200 /* 10=Sense on Rx only (Energy Detect) */ -#define GG82563_PSCR_ENERGY_DETECT_RX_TM 0x0300 /* 11=Sense and Tx NLP */ -#define GG82563_PSCR_FORCE_LINK_GOOD 0x0400 /* 1=Force Link Good */ -#define GG82563_PSCR_DOWNSHIFT_ENABLE 0x0800 /* 1=Enable Downshift */ -#define GG82563_PSCR_DOWNSHIFT_COUNTER_MASK 0x7000 -#define GG82563_PSCR_DOWNSHIFT_COUNTER_SHIFT 12 - -/* PHY Specific Status Register (Page 0, Register 17) */ -#define GG82563_PSSR_JABBER 0x0001 /* 1=Jabber */ -#define GG82563_PSSR_POLARITY 0x0002 /* 1=Polarity Reversed */ -#define GG82563_PSSR_LINK 0x0008 /* 1=Link is Up */ -#define GG82563_PSSR_ENERGY_DETECT 0x0010 /* 1=Sleep, 0=Active */ -#define GG82563_PSSR_DOWNSHIFT 0x0020 /* 1=Downshift */ -#define GG82563_PSSR_CROSSOVER_STATUS 0x0040 /* 1=MDIX, 0=MDI */ -#define GG82563_PSSR_RX_PAUSE_ENABLED 0x0100 /* 1=Receive Pause Enabled */ -#define GG82563_PSSR_TX_PAUSE_ENABLED 0x0200 /* 1=Transmit Pause Enabled */ -#define GG82563_PSSR_LINK_UP 0x0400 /* 1=Link Up */ -#define GG82563_PSSR_SPEED_DUPLEX_RESOLVED 0x0800 /* 1=Resolved */ -#define GG82563_PSSR_PAGE_RECEIVED 0x1000 /* 1=Page Received */ -#define GG82563_PSSR_DUPLEX 0x2000 /* 1-Full-Duplex */ -#define GG82563_PSSR_SPEED_MASK 0xC000 -#define GG82563_PSSR_SPEED_10MBPS 0x0000 /* 00=10Mbps */ -#define GG82563_PSSR_SPEED_100MBPS 0x4000 /* 01=100Mbps */ -#define GG82563_PSSR_SPEED_1000MBPS 0x8000 /* 10=1000Mbps */ - -/* PHY Specific Status Register 2 (Page 0, Register 19) */ -#define GG82563_PSSR2_JABBER 0x0001 /* 1=Jabber */ -#define GG82563_PSSR2_POLARITY_CHANGED 0x0002 /* 1=Polarity Changed */ -#define GG82563_PSSR2_ENERGY_DETECT_CHANGED 0x0010 /* 1=Energy Detect Changed */ -#define GG82563_PSSR2_DOWNSHIFT_INTERRUPT 0x0020 /* 1=Downshift Detected */ -#define GG82563_PSSR2_MDI_CROSSOVER_CHANGE 0x0040 /* 1=Crossover Changed */ -#define GG82563_PSSR2_FALSE_CARRIER 0x0100 /* 1=False Carrier */ -#define GG82563_PSSR2_SYMBOL_ERROR 0x0200 /* 1=Symbol Error */ -#define GG82563_PSSR2_LINK_STATUS_CHANGED 0x0400 /* 1=Link Status Changed */ -#define GG82563_PSSR2_AUTO_NEG_COMPLETED 0x0800 /* 1=Auto-Neg Completed */ -#define GG82563_PSSR2_PAGE_RECEIVED 0x1000 /* 1=Page Received */ -#define GG82563_PSSR2_DUPLEX_CHANGED 0x2000 /* 1=Duplex Changed */ -#define GG82563_PSSR2_SPEED_CHANGED 0x4000 /* 1=Speed Changed */ -#define GG82563_PSSR2_AUTO_NEG_ERROR 0x8000 /* 1=Auto-Neg Error */ - -/* PHY Specific Control Register 2 (Page 0, Register 26) */ -#define GG82563_PSCR2_10BT_POLARITY_FORCE 0x0002 /* 1=Force Negative Polarity */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_MASK 0x000C -#define GG82563_PSCR2_1000MB_TEST_SELECT_NORMAL 0x0000 /* 00,01=Normal Operation */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_112NS 0x0008 /* 10=Select 112ns Sequence */ -#define GG82563_PSCR2_1000MB_TEST_SELECT_16NS 0x000C /* 11=Select 16ns Sequence */ -#define GG82563_PSCR2_REVERSE_AUTO_NEG 0x2000 /* 1=Reverse Auto-Negotiation */ -#define GG82563_PSCR2_1000BT_DISABLE 0x4000 /* 1=Disable 1000BASE-T */ -#define GG82563_PSCR2_TRANSMITER_TYPE_MASK 0x8000 -#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_B 0x0000 /* 0=Class B */ -#define GG82563_PSCR2_TRANSMITTER_TYPE_CLASS_A 0x8000 /* 1=Class A */ - -/* MAC Specific Control Register (Page 2, Register 21) */ -/* Tx clock speed for Link Down and 1000BASE-T for the following speeds */ -#define GG82563_MSCR_TX_CLK_MASK 0x0007 -#define GG82563_MSCR_TX_CLK_10MBPS_2_5MHZ 0x0004 -#define GG82563_MSCR_TX_CLK_100MBPS_25MHZ 0x0005 -#define GG82563_MSCR_TX_CLK_1000MBPS_2_5MHZ 0x0006 -#define GG82563_MSCR_TX_CLK_1000MBPS_25MHZ 0x0007 - -#define GG82563_MSCR_ASSERT_CRS_ON_TX 0x0010 /* 1=Assert */ - -/* DSP Distance Register (Page 5, Register 26) */ -#define GG82563_DSPD_CABLE_LENGTH 0x0007 /* 0 = <50M; - 1 = 50-80M; - 2 = 80-110M; - 3 = 110-140M; - 4 = >140M */ - -/* Kumeran Mode Control Register (Page 193, Register 16) */ -#define GG82563_KMCR_PHY_LEDS_EN 0x0020 /* 1=PHY LEDs, 0=Kumeran Inband LEDs */ -#define GG82563_KMCR_FORCE_LINK_UP 0x0040 /* 1=Force Link Up */ -#define GG82563_KMCR_SUPPRESS_SGMII_EPD_EXT 0x0080 -#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT_MASK 0x0400 -#define GG82563_KMCR_MDIO_BUS_SPEED_SELECT 0x0400 /* 1=6.25MHz, 0=0.8MHz */ -#define GG82563_KMCR_PASS_FALSE_CARRIER 0x0800 - -/* Power Management Control Register (Page 193, Register 20) */ -#define GG82563_PMCR_ENABLE_ELECTRICAL_IDLE 0x0001 /* 1=Enalbe SERDES Electrical Idle */ -#define GG82563_PMCR_DISABLE_PORT 0x0002 /* 1=Disable Port */ -#define GG82563_PMCR_DISABLE_SERDES 0x0004 /* 1=Disable SERDES */ -#define GG82563_PMCR_REVERSE_AUTO_NEG 0x0008 /* 1=Enable Reverse Auto-Negotiation */ -#define GG82563_PMCR_DISABLE_1000_NON_D0 0x0010 /* 1=Disable 1000Mbps Auto-Neg in non D0 */ -#define GG82563_PMCR_DISABLE_1000 0x0020 /* 1=Disable 1000Mbps Auto-Neg Always */ -#define GG82563_PMCR_REVERSE_AUTO_NEG_D0A 0x0040 /* 1=Enable D0a Reverse Auto-Negotiation */ -#define GG82563_PMCR_FORCE_POWER_STATE 0x0080 /* 1=Force Power State */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_MASK 0x0300 -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_DR 0x0000 /* 00=Dr */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0U 0x0100 /* 01=D0u */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D0A 0x0200 /* 10=D0a */ -#define GG82563_PMCR_PROGRAMMED_POWER_STATE_D3 0x0300 /* 11=D3 */ - -/* In-Band Control Register (Page 194, Register 18) */ -#define GG82563_ICR_DIS_PADDING 0x0010 /* Disable Padding Use */ - - /* Bit definitions for valid PHY IDs. */ /* I = Integrated * E = External @@ -3154,8 +2869,6 @@ struct e1000_host_command_info { #define M88E1011_I_REV_4 0x04 #define M88E1111_I_PHY_ID 0x01410CC0 #define L1LXT971A_PHY_ID 0x001378E0 -#define GG82563_E_PHY_ID 0x01410CA0 - /* Bits... * 15-5: page @@ -3166,41 +2879,41 @@ struct e1000_host_command_info { (((page) << PHY_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS)) #define IGP3_PHY_PORT_CTRL \ - PHY_REG(769, 17) /* Port General Configuration */ + PHY_REG(769, 17) /* Port General Configuration */ #define IGP3_PHY_RATE_ADAPT_CTRL \ - PHY_REG(769, 25) /* Rate Adapter Control Register */ + PHY_REG(769, 25) /* Rate Adapter Control Register */ #define IGP3_KMRN_FIFO_CTRL_STATS \ - PHY_REG(770, 16) /* KMRN FIFO's control/status register */ + PHY_REG(770, 16) /* KMRN FIFO's control/status register */ #define IGP3_KMRN_POWER_MNG_CTRL \ - PHY_REG(770, 17) /* KMRN Power Management Control Register */ + PHY_REG(770, 17) /* KMRN Power Management Control Register */ #define IGP3_KMRN_INBAND_CTRL \ - PHY_REG(770, 18) /* KMRN Inband Control Register */ + PHY_REG(770, 18) /* KMRN Inband Control Register */ #define IGP3_KMRN_DIAG \ - PHY_REG(770, 19) /* KMRN Diagnostic register */ -#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */ + PHY_REG(770, 19) /* KMRN Diagnostic register */ +#define IGP3_KMRN_DIAG_PCS_LOCK_LOSS 0x0002 /* RX PCS is not synced */ #define IGP3_KMRN_ACK_TIMEOUT \ - PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */ + PHY_REG(770, 20) /* KMRN Acknowledge Timeouts register */ #define IGP3_VR_CTRL \ - PHY_REG(776, 18) /* Voltage regulator control register */ -#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */ -#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */ + PHY_REG(776, 18) /* Voltage regulator control register */ +#define IGP3_VR_CTRL_MODE_SHUT 0x0200 /* Enter powerdown, shutdown VRs */ +#define IGP3_VR_CTRL_MODE_MASK 0x0300 /* Shutdown VR Mask */ #define IGP3_CAPABILITY \ - PHY_REG(776, 19) /* IGP3 Capability Register */ + PHY_REG(776, 19) /* IGP3 Capability Register */ /* Capabilities for SKU Control */ -#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */ -#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */ -#define IGP3_CAP_ASF 0x0004 /* Support ASF */ -#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */ -#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */ -#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */ -#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */ -#define IGP3_CAP_RSS 0x0080 /* Support RSS */ -#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */ -#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */ +#define IGP3_CAP_INITIATE_TEAM 0x0001 /* Able to initiate a team */ +#define IGP3_CAP_WFM 0x0002 /* Support WoL and PXE */ +#define IGP3_CAP_ASF 0x0004 /* Support ASF */ +#define IGP3_CAP_LPLU 0x0008 /* Support Low Power Link Up */ +#define IGP3_CAP_DC_AUTO_SPEED 0x0010 /* Support AC/DC Auto Link Speed */ +#define IGP3_CAP_SPD 0x0020 /* Support Smart Power Down */ +#define IGP3_CAP_MULT_QUEUE 0x0040 /* Support 2 tx & 2 rx queues */ +#define IGP3_CAP_RSS 0x0080 /* Support RSS */ +#define IGP3_CAP_8021PQ 0x0100 /* Support 802.1Q & 802.1p */ +#define IGP3_CAP_AMT_CB 0x0200 /* Support active manageability and circuit breaker */ #define IGP3_PPC_JORDAN_EN 0x0001 #define IGP3_PPC_JORDAN_GIGA_SPEED 0x0002 @@ -3210,69 +2923,69 @@ struct e1000_host_command_info { #define IGP3_KMRN_PMC_K0S_MODE1_EN_GIGA 0x0020 #define IGP3_KMRN_PMC_K0S_MODE1_EN_100 0x0040 -#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */ -#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */ +#define IGP3E1000_PHY_MISC_CTRL 0x1B /* Misc. Ctrl register */ +#define IGP3_PHY_MISC_DUPLEX_MANUAL_SET 0x1000 /* Duplex Manual Set */ #define IGP3_KMRN_EXT_CTRL PHY_REG(770, 18) #define IGP3_KMRN_EC_DIS_INBAND 0x0080 #define IGP03E1000_E_PHY_ID 0x02A80390 -#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */ +#define IFE_E_PHY_ID 0x02A80330 /* 10/100 PHY */ #define IFE_PLUS_E_PHY_ID 0x02A80320 #define IFE_C_E_PHY_ID 0x02A80310 -#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */ -#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */ -#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */ -#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnet Counter */ -#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */ -#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */ -#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */ -#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */ -#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */ -#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */ -#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */ -#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */ -#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */ - -#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Defaut 1 = Disable auto reduced power down */ -#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */ -#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */ -#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */ -#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */ -#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */ -#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */ +#define IFE_PHY_EXTENDED_STATUS_CONTROL 0x10 /* 100BaseTx Extended Status, Control and Address */ +#define IFE_PHY_SPECIAL_CONTROL 0x11 /* 100BaseTx PHY special control register */ +#define IFE_PHY_RCV_FALSE_CARRIER 0x13 /* 100BaseTx Receive False Carrier Counter */ +#define IFE_PHY_RCV_DISCONNECT 0x14 /* 100BaseTx Receive Disconnect Counter */ +#define IFE_PHY_RCV_ERROT_FRAME 0x15 /* 100BaseTx Receive Error Frame Counter */ +#define IFE_PHY_RCV_SYMBOL_ERR 0x16 /* Receive Symbol Error Counter */ +#define IFE_PHY_PREM_EOF_ERR 0x17 /* 100BaseTx Receive Premature End Of Frame Error Counter */ +#define IFE_PHY_RCV_EOF_ERR 0x18 /* 10BaseT Receive End Of Frame Error Counter */ +#define IFE_PHY_TX_JABBER_DETECT 0x19 /* 10BaseT Transmit Jabber Detect Counter */ +#define IFE_PHY_EQUALIZER 0x1A /* PHY Equalizer Control and Status */ +#define IFE_PHY_SPECIAL_CONTROL_LED 0x1B /* PHY special control and LED configuration */ +#define IFE_PHY_MDIX_CONTROL 0x1C /* MDI/MDI-X Control register */ +#define IFE_PHY_HWI_CONTROL 0x1D /* Hardware Integrity Control (HWI) */ + +#define IFE_PESC_REDUCED_POWER_DOWN_DISABLE 0x2000 /* Default 1 = Disable auto reduced power down */ +#define IFE_PESC_100BTX_POWER_DOWN 0x0400 /* Indicates the power state of 100BASE-TX */ +#define IFE_PESC_10BTX_POWER_DOWN 0x0200 /* Indicates the power state of 10BASE-T */ +#define IFE_PESC_POLARITY_REVERSED 0x0100 /* Indicates 10BASE-T polarity */ +#define IFE_PESC_PHY_ADDR_MASK 0x007C /* Bit 6:2 for sampled PHY address */ +#define IFE_PESC_SPEED 0x0002 /* Auto-negotiation speed result 1=100Mbs, 0=10Mbs */ +#define IFE_PESC_DUPLEX 0x0001 /* Auto-negotiation duplex result 1=Full, 0=Half */ #define IFE_PESC_POLARITY_REVERSED_SHIFT 8 -#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dyanmic Power Down disabled */ -#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */ -#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */ -#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */ +#define IFE_PSC_DISABLE_DYNAMIC_POWER_DOWN 0x0100 /* 1 = Dynamic Power Down disabled */ +#define IFE_PSC_FORCE_POLARITY 0x0020 /* 1=Reversed Polarity, 0=Normal */ +#define IFE_PSC_AUTO_POLARITY_DISABLE 0x0010 /* 1=Auto Polarity Disabled, 0=Enabled */ +#define IFE_PSC_JABBER_FUNC_DISABLE 0x0001 /* 1=Jabber Disabled, 0=Normal Jabber Operation */ #define IFE_PSC_FORCE_POLARITY_SHIFT 5 #define IFE_PSC_AUTO_POLARITY_DISABLE_SHIFT 4 -#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */ -#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */ -#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */ -#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorithm is completed */ +#define IFE_PMC_AUTO_MDIX 0x0080 /* 1=enable MDI/MDI-X feature, default 0=disabled */ +#define IFE_PMC_FORCE_MDIX 0x0040 /* 1=force MDIX-X, 0=force MDI */ +#define IFE_PMC_MDIX_STATUS 0x0020 /* 1=MDI-X, 0=MDI */ +#define IFE_PMC_AUTO_MDIX_COMPLETE 0x0010 /* Resolution algorithm is completed */ #define IFE_PMC_MDIX_MODE_SHIFT 6 -#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */ - -#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */ -#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */ -#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */ -#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */ -#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */ -#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */ -#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */ -#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */ -#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */ -#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */ -#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */ - -#define ICH_FLASH_COMMAND_TIMEOUT 5000 /* 5000 uSecs - adjusted */ -#define ICH_FLASH_ERASE_TIMEOUT 3000000 /* Up to 3 seconds - worst case */ -#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles */ +#define IFE_PHC_MDIX_RESET_ALL_MASK 0x0000 /* Disable auto MDI-X */ + +#define IFE_PHC_HWI_ENABLE 0x8000 /* Enable the HWI feature */ +#define IFE_PHC_ABILITY_CHECK 0x4000 /* 1= Test Passed, 0=failed */ +#define IFE_PHC_TEST_EXEC 0x2000 /* PHY launch test pulses on the wire */ +#define IFE_PHC_HIGHZ 0x0200 /* 1 = Open Circuit */ +#define IFE_PHC_LOWZ 0x0400 /* 1 = Short Circuit */ +#define IFE_PHC_LOW_HIGH_Z_MASK 0x0600 /* Mask for indication type of problem on the line */ +#define IFE_PHC_DISTANCE_MASK 0x01FF /* Mask for distance to the cable problem, in 80cm granularity */ +#define IFE_PHC_RESET_ALL_MASK 0x0000 /* Disable HWI */ +#define IFE_PSCL_PROBE_MODE 0x0020 /* LED Probe mode */ +#define IFE_PSCL_PROBE_LEDS_OFF 0x0006 /* Force LEDs 0 and 2 off */ +#define IFE_PSCL_PROBE_LEDS_ON 0x0007 /* Force LEDs 0 and 2 on */ + +#define ICH_FLASH_COMMAND_TIMEOUT 5000 /* 5000 uSecs - adjusted */ +#define ICH_FLASH_ERASE_TIMEOUT 3000000 /* Up to 3 seconds - worst case */ +#define ICH_FLASH_CYCLE_REPEAT_COUNT 10 /* 10 cycles */ #define ICH_FLASH_SEG_SIZE_256 256 #define ICH_FLASH_SEG_SIZE_4K 4096 #define ICH_FLASH_SEG_SIZE_64K 65536 @@ -3305,74 +3018,6 @@ struct e1000_host_command_info { #define ICH_GFPREG_BASE_MASK 0x1FFF #define ICH_FLASH_LINEAR_ADDR_MASK 0x00FFFFFF -/* ICH8 GbE Flash Hardware Sequencing Flash Status Register bit breakdown */ -/* Offset 04h HSFSTS */ -union ich8_hws_flash_status { - struct ich8_hsfsts { -#ifdef __BIG_ENDIAN - u16 reserved2 :6; - u16 fldesvalid :1; - u16 flockdn :1; - u16 flcdone :1; - u16 flcerr :1; - u16 dael :1; - u16 berasesz :2; - u16 flcinprog :1; - u16 reserved1 :2; -#else - u16 flcdone :1; /* bit 0 Flash Cycle Done */ - u16 flcerr :1; /* bit 1 Flash Cycle Error */ - u16 dael :1; /* bit 2 Direct Access error Log */ - u16 berasesz :2; /* bit 4:3 Block/Sector Erase Size */ - u16 flcinprog :1; /* bit 5 flash SPI cycle in Progress */ - u16 reserved1 :2; /* bit 13:6 Reserved */ - u16 reserved2 :6; /* bit 13:6 Reserved */ - u16 fldesvalid :1; /* bit 14 Flash Descriptor Valid */ - u16 flockdn :1; /* bit 15 Flash Configuration Lock-Down */ -#endif - } hsf_status; - u16 regval; -}; - -/* ICH8 GbE Flash Hardware Sequencing Flash control Register bit breakdown */ -/* Offset 06h FLCTL */ -union ich8_hws_flash_ctrl { - struct ich8_hsflctl { -#ifdef __BIG_ENDIAN - u16 fldbcount :2; - u16 flockdn :6; - u16 flcgo :1; - u16 flcycle :2; - u16 reserved :5; -#else - u16 flcgo :1; /* 0 Flash Cycle Go */ - u16 flcycle :2; /* 2:1 Flash Cycle */ - u16 reserved :5; /* 7:3 Reserved */ - u16 fldbcount :2; /* 9:8 Flash Data Byte Count */ - u16 flockdn :6; /* 15:10 Reserved */ -#endif - } hsf_ctrl; - u16 regval; -}; - -/* ICH8 Flash Region Access Permissions */ -union ich8_hws_flash_regacc { - struct ich8_flracc { -#ifdef __BIG_ENDIAN - u32 gmwag :8; - u32 gmrag :8; - u32 grwa :8; - u32 grra :8; -#else - u32 grra :8; /* 0:7 GbE region Read Access */ - u32 grwa :8; /* 8:15 GbE region Write Access */ - u32 gmrag :8; /* 23:16 GbE Master Read Access Grant */ - u32 gmwag :8; /* 31:24 GbE Master Write Access Grant */ -#endif - } hsf_flregacc; - u16 regval; -}; - /* Miscellaneous PHY bit definitions. */ #define PHY_PREAMBLE 0xFFFFFFFF #define PHY_SOF 0x01 @@ -3384,10 +3029,10 @@ union ich8_hws_flash_regacc { #define MII_CR_SPEED_100 0x2000 #define MII_CR_SPEED_10 0x0000 #define E1000_PHY_ADDRESS 0x01 -#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */ -#define PHY_FORCE_TIME 20 /* 2.0 Seconds */ +#define PHY_AUTO_NEG_TIME 45 /* 4.5 Seconds */ +#define PHY_FORCE_TIME 20 /* 2.0 Seconds */ #define PHY_REVISION_MASK 0xFFFFFFF0 -#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */ +#define DEVICE_SPEED_MASK 0x00000300 /* Device Ctrl Reg Speed Mask */ #define REG4_SPEED_MASK 0x01E0 #define REG9_SPEED_MASK 0x0300 #define ADVERTISE_10_HALF 0x0001 @@ -3396,8 +3041,8 @@ union ich8_hws_flash_regacc { #define ADVERTISE_100_FULL 0x0008 #define ADVERTISE_1000_HALF 0x0010 #define ADVERTISE_1000_FULL 0x0020 -#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */ -#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds*/ -#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds*/ +#define AUTONEG_ADVERTISE_SPEED_DEFAULT 0x002F /* Everything but 1000-Half */ +#define AUTONEG_ADVERTISE_10_100_ALL 0x000F /* All 10/100 speeds */ +#define AUTONEG_ADVERTISE_10_ALL 0x0003 /* 10Mbps Full & Half speeds */ #endif /* _E1000_HW_H_ */ diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c index c66dd4f9437..bcd192ca47b 100644 --- a/drivers/net/e1000/e1000_main.c +++ b/drivers/net/e1000/e1000_main.c @@ -31,7 +31,7 @@ char e1000_driver_name[] = "e1000"; static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver"; -#define DRV_VERSION "7.3.21-k3-NAPI" +#define DRV_VERSION "7.3.21-k5-NAPI" const char e1000_driver_version[] = DRV_VERSION; static const char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation."; @@ -131,7 +131,6 @@ static struct net_device_stats * e1000_get_stats(struct net_device *netdev); static int e1000_change_mtu(struct net_device *netdev, int new_mtu); static int e1000_set_mac(struct net_device *netdev, void *p); static irqreturn_t e1000_intr(int irq, void *data); -static irqreturn_t e1000_intr_msi(int irq, void *data); static bool e1000_clean_tx_irq(struct e1000_adapter *adapter, struct e1000_tx_ring *tx_ring); static int e1000_clean(struct napi_struct *napi, int budget); @@ -258,25 +257,14 @@ module_exit(e1000_exit_module); static int e1000_request_irq(struct e1000_adapter *adapter) { - struct e1000_hw *hw = &adapter->hw; struct net_device *netdev = adapter->netdev; irq_handler_t handler = e1000_intr; int irq_flags = IRQF_SHARED; int err; - if (hw->mac_type >= e1000_82571) { - adapter->have_msi = !pci_enable_msi(adapter->pdev); - if (adapter->have_msi) { - handler = e1000_intr_msi; - irq_flags = 0; - } - } - err = request_irq(adapter->pdev->irq, handler, irq_flags, netdev->name, netdev); if (err) { - if (adapter->have_msi) - pci_disable_msi(adapter->pdev); DPRINTK(PROBE, ERR, "Unable to allocate interrupt Error: %d\n", err); } @@ -289,9 +277,6 @@ static void e1000_free_irq(struct e1000_adapter *adapter) struct net_device *netdev = adapter->netdev; free_irq(adapter->pdev->irq, netdev); - - if (adapter->have_msi) - pci_disable_msi(adapter->pdev); } /** @@ -345,76 +330,6 @@ static void e1000_update_mng_vlan(struct e1000_adapter *adapter) } } -/** - * e1000_release_hw_control - release control of the h/w to f/w - * @adapter: address of board private structure - * - * e1000_release_hw_control resets {CTRL_EXT|FWSM}:DRV_LOAD bit. - * For ASF and Pass Through versions of f/w this means that the - * driver is no longer loaded. For AMT version (only with 82573) i - * of the f/w this means that the network i/f is closed. - * - **/ - -static void e1000_release_hw_control(struct e1000_adapter *adapter) -{ - u32 ctrl_ext; - u32 swsm; - struct e1000_hw *hw = &adapter->hw; - - /* Let firmware taken over control of h/w */ - switch (hw->mac_type) { - case e1000_82573: - swsm = er32(SWSM); - ew32(SWSM, swsm & ~E1000_SWSM_DRV_LOAD); - break; - case e1000_82571: - case e1000_82572: - case e1000_80003es2lan: - case e1000_ich8lan: - ctrl_ext = er32(CTRL_EXT); - ew32(CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_DRV_LOAD); - break; - default: - break; - } -} - -/** - * e1000_get_hw_control - get control of the h/w from f/w - * @adapter: address of board private structure - * - * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit. - * For ASF and Pass Through versions of f/w this means that - * the driver is loaded. For AMT version (only with 82573) - * of the f/w this means that the network i/f is open. - * - **/ - -static void e1000_get_hw_control(struct e1000_adapter *adapter) -{ - u32 ctrl_ext; - u32 swsm; - struct e1000_hw *hw = &adapter->hw; - - /* Let firmware know the driver has taken over */ - switch (hw->mac_type) { - case e1000_82573: - swsm = er32(SWSM); - ew32(SWSM, swsm | E1000_SWSM_DRV_LOAD); - break; - case e1000_82571: - case e1000_82572: - case e1000_80003es2lan: - case e1000_ich8lan: - ctrl_ext = er32(CTRL_EXT); - ew32(CTRL_EXT, ctrl_ext | E1000_CTRL_EXT_DRV_LOAD); - break; - default: - break; - } -} - static void e1000_init_manageability(struct e1000_adapter *adapter) { struct e1000_hw *hw = &adapter->hw; @@ -425,20 +340,6 @@ static void e1000_init_manageability(struct e1000_adapter *adapter) /* disable hardware interception of ARP */ manc &= ~(E1000_MANC_ARP_EN); - /* enable receiving management packets to the host */ - /* this will probably generate destination unreachable messages - * from the host OS, but the packets will be handled on SMBUS */ - if (hw->has_manc2h) { - u32 manc2h = er32(MANC2H); - - manc |= E1000_MANC_EN_MNG2HOST; -#define E1000_MNG2HOST_PORT_623 (1 << 5) -#define E1000_MNG2HOST_PORT_664 (1 << 6) - manc2h |= E1000_MNG2HOST_PORT_623; - manc2h |= E1000_MNG2HOST_PORT_664; - ew32(MANC2H, manc2h); - } - ew32(MANC, manc); } } @@ -453,12 +354,6 @@ static void e1000_release_manageability(struct e1000_adapter *adapter) /* re-enable hardware interception of ARP */ manc |= E1000_MANC_ARP_EN; - if (hw->has_manc2h) - manc &= ~E1000_MANC_EN_MNG2HOST; - - /* don't explicitly have to mess with MANC2H since - * MANC has an enable disable that gates MANC2H */ - ew32(MANC, manc); } } @@ -563,15 +458,6 @@ static void e1000_power_down_phy(struct e1000_adapter *adapter) if (er32(MANC) & E1000_MANC_SMBUS_EN) goto out; break; - case e1000_82571: - case e1000_82572: - case e1000_82573: - case e1000_80003es2lan: - case e1000_ich8lan: - if (e1000_check_mng_mode(hw) || - e1000_check_phy_reset_block(hw)) - goto out; - break; default: goto out; } @@ -599,8 +485,7 @@ void e1000_down(struct e1000_adapter *adapter) ew32(RCTL, rctl & ~E1000_RCTL_EN); /* flush and sleep below */ - /* can be netif_tx_disable when NETIF_F_LLTX is removed */ - netif_stop_queue(netdev); + netif_tx_disable(netdev); /* disable transmits in the hardware */ tctl = er32(TCTL); @@ -671,16 +556,6 @@ void e1000_reset(struct e1000_adapter *adapter) legacy_pba_adjust = true; pba = E1000_PBA_30K; break; - case e1000_82571: - case e1000_82572: - case e1000_80003es2lan: - pba = E1000_PBA_38K; - break; - case e1000_82573: - pba = E1000_PBA_20K; - break; - case e1000_ich8lan: - pba = E1000_PBA_8K; case e1000_undefined: case e1000_num_macs: break; @@ -744,16 +619,8 @@ void e1000_reset(struct e1000_adapter *adapter) /* if short on rx space, rx wins and must trump tx * adjustment or use Early Receive if available */ - if (pba < min_rx_space) { - switch (hw->mac_type) { - case e1000_82573: - /* ERT enabled in e1000_configure_rx */ - break; - default: - pba = min_rx_space; - break; - } - } + if (pba < min_rx_space) + pba = min_rx_space; } } @@ -789,7 +656,6 @@ void e1000_reset(struct e1000_adapter *adapter) /* if (adapter->hwflags & HWFLAGS_PHY_PWR_BIT) { */ if (hw->mac_type >= e1000_82544 && - hw->mac_type <= e1000_82547_rev_2 && hw->autoneg == 1 && hw->autoneg_advertised == ADVERTISE_1000_FULL) { u32 ctrl = er32(CTRL); @@ -806,20 +672,6 @@ void e1000_reset(struct e1000_adapter *adapter) e1000_reset_adaptive(hw); e1000_phy_get_info(hw, &adapter->phy_info); - if (!adapter->smart_power_down && - (hw->mac_type == e1000_82571 || - hw->mac_type == e1000_82572)) { - u16 phy_data = 0; - /* speed up time to link by disabling smart power down, ignore - * the return value of this function because there is nothing - * different we would do if it failed */ - e1000_read_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, - &phy_data); - phy_data &= ~IGP02E1000_PM_SPD; - e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, - phy_data); - } - e1000_release_manageability(adapter); } @@ -1046,17 +898,6 @@ static int __devinit e1000_probe(struct pci_dev *pdev, goto err_sw_init; err = -EIO; - /* Flash BAR mapping must happen after e1000_sw_init - * because it depends on mac_type */ - if ((hw->mac_type == e1000_ich8lan) && - (pci_resource_flags(pdev, 1) & IORESOURCE_MEM)) { - hw->flash_address = pci_ioremap_bar(pdev, 1); - if (!hw->flash_address) - goto err_flashmap; - } - - if (e1000_check_phy_reset_block(hw)) - DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n"); if (hw->mac_type >= e1000_82543) { netdev->features = NETIF_F_SG | @@ -1064,21 +905,16 @@ static int __devinit e1000_probe(struct pci_dev *pdev, NETIF_F_HW_VLAN_TX | NETIF_F_HW_VLAN_RX | NETIF_F_HW_VLAN_FILTER; - if (hw->mac_type == e1000_ich8lan) - netdev->features &= ~NETIF_F_HW_VLAN_FILTER; } if ((hw->mac_type >= e1000_82544) && (hw->mac_type != e1000_82547)) netdev->features |= NETIF_F_TSO; - if (hw->mac_type > e1000_82547_rev_2) - netdev->features |= NETIF_F_TSO6; if (pci_using_dac) netdev->features |= NETIF_F_HIGHDMA; netdev->vlan_features |= NETIF_F_TSO; - netdev->vlan_features |= NETIF_F_TSO6; netdev->vlan_features |= NETIF_F_HW_CSUM; netdev->vlan_features |= NETIF_F_SG; @@ -1153,15 +989,8 @@ static int __devinit e1000_probe(struct pci_dev *pdev, EEPROM_INIT_CONTROL2_REG, 1, &eeprom_data); eeprom_apme_mask = E1000_EEPROM_82544_APM; break; - case e1000_ich8lan: - e1000_read_eeprom(hw, - EEPROM_INIT_CONTROL1_REG, 1, &eeprom_data); - eeprom_apme_mask = E1000_EEPROM_ICH8_APME; - break; case e1000_82546: case e1000_82546_rev_3: - case e1000_82571: - case e1000_80003es2lan: if (er32(STATUS) & E1000_STATUS_FUNC_1){ e1000_read_eeprom(hw, EEPROM_INIT_CONTROL3_PORT_B, 1, &eeprom_data); @@ -1185,17 +1014,12 @@ static int __devinit e1000_probe(struct pci_dev *pdev, break; case E1000_DEV_ID_82546EB_FIBER: case E1000_DEV_ID_82546GB_FIBER: - case E1000_DEV_ID_82571EB_FIBER: /* Wake events only supported on port A for dual fiber * regardless of eeprom setting */ if (er32(STATUS) & E1000_STATUS_FUNC_1) adapter->eeprom_wol = 0; break; case E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3: - case E1000_DEV_ID_82571EB_QUAD_COPPER: - case E1000_DEV_ID_82571EB_QUAD_FIBER: - case E1000_DEV_ID_82571EB_QUAD_COPPER_LOWPROFILE: - case E1000_DEV_ID_82571PT_QUAD_COPPER: /* if quad port adapter, disable WoL on all but port A */ if (global_quad_port_a != 0) adapter->eeprom_wol = 0; @@ -1213,39 +1037,18 @@ static int __devinit e1000_probe(struct pci_dev *pdev, /* print bus type/speed/width info */ DPRINTK(PROBE, INFO, "(PCI%s:%s:%s) ", - ((hw->bus_type == e1000_bus_type_pcix) ? "-X" : - (hw->bus_type == e1000_bus_type_pci_express ? " Express":"")), - ((hw->bus_speed == e1000_bus_speed_2500) ? "2.5Gb/s" : - (hw->bus_speed == e1000_bus_speed_133) ? "133MHz" : + ((hw->bus_type == e1000_bus_type_pcix) ? "-X" : ""), + ((hw->bus_speed == e1000_bus_speed_133) ? "133MHz" : (hw->bus_speed == e1000_bus_speed_120) ? "120MHz" : (hw->bus_speed == e1000_bus_speed_100) ? "100MHz" : (hw->bus_speed == e1000_bus_speed_66) ? "66MHz" : "33MHz"), - ((hw->bus_width == e1000_bus_width_64) ? "64-bit" : - (hw->bus_width == e1000_bus_width_pciex_4) ? "Width x4" : - (hw->bus_width == e1000_bus_width_pciex_1) ? "Width x1" : - "32-bit")); + ((hw->bus_width == e1000_bus_width_64) ? "64-bit" : "32-bit")); printk("%pM\n", netdev->dev_addr); - if (hw->bus_type == e1000_bus_type_pci_express) { - DPRINTK(PROBE, WARNING, "This device (id %04x:%04x) will no " - "longer be supported by this driver in the future.\n", - pdev->vendor, pdev->device); - DPRINTK(PROBE, WARNING, "please use the \"e1000e\" " - "driver instead.\n"); - } - /* reset the hardware with the new settings */ e1000_reset(adapter); - /* If the controller is 82573 and f/w is AMT, do not set - * DRV_LOAD until the interface is up. For all other cases, - * let the f/w know that the h/w is now under the control - * of the driver. */ - if (hw->mac_type != e1000_82573 || - !e1000_check_mng_mode(hw)) - e1000_get_hw_control(adapter); - strcpy(netdev->name, "eth%d"); err = register_netdev(netdev); if (err) @@ -1260,14 +1063,11 @@ static int __devinit e1000_probe(struct pci_dev *pdev, return 0; err_register: - e1000_release_hw_control(adapter); err_eeprom: - if (!e1000_check_phy_reset_block(hw)) - e1000_phy_hw_reset(hw); + e1000_phy_hw_reset(hw); if (hw->flash_address) iounmap(hw->flash_address); -err_flashmap: kfree(adapter->tx_ring); kfree(adapter->rx_ring); err_sw_init: @@ -1298,18 +1098,18 @@ static void __devexit e1000_remove(struct pci_dev *pdev) struct e1000_adapter *adapter = netdev_priv(netdev); struct e1000_hw *hw = &adapter->hw; + set_bit(__E1000_DOWN, &adapter->flags); + del_timer_sync(&adapter->tx_fifo_stall_timer); + del_timer_sync(&adapter->watchdog_timer); + del_timer_sync(&adapter->phy_info_timer); + cancel_work_sync(&adapter->reset_task); e1000_release_manageability(adapter); - /* Release control of h/w to f/w. If f/w is AMT enabled, this - * would have already happened in close and is redundant. */ - e1000_release_hw_control(adapter); - unregister_netdev(netdev); - if (!e1000_check_phy_reset_block(hw)) - e1000_phy_hw_reset(hw); + e1000_phy_hw_reset(hw); kfree(adapter->tx_ring); kfree(adapter->rx_ring); @@ -1472,12 +1272,6 @@ static int e1000_open(struct net_device *netdev) e1000_update_mng_vlan(adapter); } - /* If AMT is enabled, let the firmware know that the network - * interface is now open */ - if (hw->mac_type == e1000_82573 && - e1000_check_mng_mode(hw)) - e1000_get_hw_control(adapter); - /* before we allocate an interrupt, we must be ready to handle it. * Setting DEBUG_SHIRQ in the kernel makes it fire an interrupt * as soon as we call pci_request_irq, so we have to setup our @@ -1503,7 +1297,6 @@ static int e1000_open(struct net_device *netdev) return E1000_SUCCESS; err_req_irq: - e1000_release_hw_control(adapter); e1000_power_down_phy(adapter); e1000_free_all_rx_resources(adapter); err_setup_rx: @@ -1548,12 +1341,6 @@ static int e1000_close(struct net_device *netdev) e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id); } - /* If AMT is enabled, let the firmware know that the network - * interface is now closed */ - if (hw->mac_type == e1000_82573 && - e1000_check_mng_mode(hw)) - e1000_release_hw_control(adapter); - return 0; } @@ -1692,7 +1479,7 @@ static void e1000_configure_tx(struct e1000_adapter *adapter) { u64 tdba; struct e1000_hw *hw = &adapter->hw; - u32 tdlen, tctl, tipg, tarc; + u32 tdlen, tctl, tipg; u32 ipgr1, ipgr2; /* Setup the HW Tx Head and Tail descriptor pointers */ @@ -1714,8 +1501,7 @@ static void e1000_configure_tx(struct e1000_adapter *adapter) } /* Set the default values for the Tx Inter Packet Gap timer */ - if (hw->mac_type <= e1000_82547_rev_2 && - (hw->media_type == e1000_media_type_fiber || + if ((hw->media_type == e1000_media_type_fiber || hw->media_type == e1000_media_type_internal_serdes)) tipg = DEFAULT_82543_TIPG_IPGT_FIBER; else @@ -1728,10 +1514,6 @@ static void e1000_configure_tx(struct e1000_adapter *adapter) ipgr1 = DEFAULT_82542_TIPG_IPGR1; ipgr2 = DEFAULT_82542_TIPG_IPGR2; break; - case e1000_80003es2lan: - ipgr1 = DEFAULT_82543_TIPG_IPGR1; - ipgr2 = DEFAULT_80003ES2LAN_TIPG_IPGR2; - break; default: ipgr1 = DEFAULT_82543_TIPG_IPGR1; ipgr2 = DEFAULT_82543_TIPG_IPGR2; @@ -1754,21 +1536,6 @@ static void e1000_configure_tx(struct e1000_adapter *adapter) tctl |= E1000_TCTL_PSP | E1000_TCTL_RTLC | (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT); - if (hw->mac_type == e1000_82571 || hw->mac_type == e1000_82572) { - tarc = er32(TARC0); - /* set the speed mode bit, we'll clear it if we're not at - * gigabit link later */ - tarc |= (1 << 21); - ew32(TARC0, tarc); - } else if (hw->mac_type == e1000_80003es2lan) { - tarc = er32(TARC0); - tarc |= 1; - ew32(TARC0, tarc); - tarc = er32(TARC1); - tarc |= 1; - ew32(TARC1, tarc); - } - e1000_config_collision_dist(hw); /* Setup Transmit Descriptor Settings for eop descriptor */ @@ -1804,7 +1571,6 @@ static void e1000_configure_tx(struct e1000_adapter *adapter) static int e1000_setup_rx_resources(struct e1000_adapter *adapter, struct e1000_rx_ring *rxdr) { - struct e1000_hw *hw = &adapter->hw; struct pci_dev *pdev = adapter->pdev; int size, desc_len; @@ -1817,10 +1583,7 @@ static int e1000_setup_rx_resources(struct e1000_adapter *adapter, } memset(rxdr->buffer_info, 0, size); - if (hw->mac_type <= e1000_82547_rev_2) - desc_len = sizeof(struct e1000_rx_desc); - else - desc_len = sizeof(union e1000_rx_desc_packet_split); + desc_len = sizeof(struct e1000_rx_desc); /* Round up to nearest 4K */ @@ -1977,7 +1740,7 @@ static void e1000_configure_rx(struct e1000_adapter *adapter) { u64 rdba; struct e1000_hw *hw = &adapter->hw; - u32 rdlen, rctl, rxcsum, ctrl_ext; + u32 rdlen, rctl, rxcsum; if (adapter->netdev->mtu > ETH_DATA_LEN) { rdlen = adapter->rx_ring[0].count * @@ -2004,17 +1767,6 @@ static void e1000_configure_rx(struct e1000_adapter *adapter) ew32(ITR, 1000000000 / (adapter->itr * 256)); } - if (hw->mac_type >= e1000_82571) { - ctrl_ext = er32(CTRL_EXT); - /* Reset delay timers after every interrupt */ - ctrl_ext |= E1000_CTRL_EXT_INT_TIMER_CLR; - /* Auto-Mask interrupts upon ICR access */ - ctrl_ext |= E1000_CTRL_EXT_IAME; - ew32(IAM, 0xffffffff); - ew32(CTRL_EXT, ctrl_ext); - E1000_WRITE_FLUSH(); - } - /* Setup the HW Rx Head and Tail Descriptor Pointers and * the Base and Length of the Rx Descriptor Ring */ switch (adapter->num_rx_queues) { @@ -2329,22 +2081,6 @@ static int e1000_set_mac(struct net_device *netdev, void *p) e1000_rar_set(hw, hw->mac_addr, 0); - /* With 82571 controllers, LAA may be overwritten (with the default) - * due to controller reset from the other port. */ - if (hw->mac_type == e1000_82571) { - /* activate the work around */ - hw->laa_is_present = 1; - - /* Hold a copy of the LAA in RAR[14] This is done so that - * between the time RAR[0] gets clobbered and the time it - * gets fixed (in e1000_watchdog), the actual LAA is in one - * of the RARs and no incoming packets directed to this port - * are dropped. Eventaully the LAA will be in RAR[0] and - * RAR[14] */ - e1000_rar_set(hw, hw->mac_addr, - E1000_RAR_ENTRIES - 1); - } - if (hw->mac_type == e1000_82542_rev2_0) e1000_leave_82542_rst(adapter); @@ -2371,9 +2107,7 @@ static void e1000_set_rx_mode(struct net_device *netdev) u32 rctl; u32 hash_value; int i, rar_entries = E1000_RAR_ENTRIES; - int mta_reg_count = (hw->mac_type == e1000_ich8lan) ? - E1000_NUM_MTA_REGISTERS_ICH8LAN : - E1000_NUM_MTA_REGISTERS; + int mta_reg_count = E1000_NUM_MTA_REGISTERS; u32 *mcarray = kcalloc(mta_reg_count, sizeof(u32), GFP_ATOMIC); if (!mcarray) { @@ -2381,13 +2115,6 @@ static void e1000_set_rx_mode(struct net_device *netdev) return; } - if (hw->mac_type == e1000_ich8lan) - rar_entries = E1000_RAR_ENTRIES_ICH8LAN; - - /* reserve RAR[14] for LAA over-write work-around */ - if (hw->mac_type == e1000_82571) - rar_entries--; - /* Check for Promiscuous and All Multicast modes */ rctl = er32(RCTL); @@ -2396,15 +2123,13 @@ static void e1000_set_rx_mode(struct net_device *netdev) rctl |= (E1000_RCTL_UPE | E1000_RCTL_MPE); rctl &= ~E1000_RCTL_VFE; } else { - if (netdev->flags & IFF_ALLMULTI) { + if (netdev->flags & IFF_ALLMULTI) rctl |= E1000_RCTL_MPE; - } else { + else rctl &= ~E1000_RCTL_MPE; - } - if (adapter->hw.mac_type != e1000_ich8lan) - /* Enable VLAN filter if there is a VLAN */ - if (adapter->vlgrp) - rctl |= E1000_RCTL_VFE; + /* Enable VLAN filter if there is a VLAN */ + if (adapter->vlgrp) + rctl |= E1000_RCTL_VFE; } if (netdev->uc.count > rar_entries - 1) { @@ -2427,7 +2152,6 @@ static void e1000_set_rx_mode(struct net_device *netdev) * * RAR 0 is used for the station MAC adddress * if there are not 14 addresses, go ahead and clear the filters - * -- with 82571 controllers only 0-13 entries are filled here */ i = 1; if (use_uc) @@ -2521,12 +2245,46 @@ static void e1000_82547_tx_fifo_stall(unsigned long data) adapter->tx_fifo_head = 0; atomic_set(&adapter->tx_fifo_stall, 0); netif_wake_queue(netdev); - } else { + } else if (!test_bit(__E1000_DOWN, &adapter->flags)) { mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1); } } } +static bool e1000_has_link(struct e1000_adapter *adapter) +{ + struct e1000_hw *hw = &adapter->hw; + bool link_active = false; + + /* get_link_status is set on LSC (link status) interrupt or + * rx sequence error interrupt. get_link_status will stay + * false until the e1000_check_for_link establishes link + * for copper adapters ONLY + */ + switch (hw->media_type) { + case e1000_media_type_copper: + if (hw->get_link_status) { + e1000_check_for_link(hw); + link_active = !hw->get_link_status; + } else { + link_active = true; + } + break; + case e1000_media_type_fiber: + e1000_check_for_link(hw); + link_active = !!(er32(STATUS) & E1000_STATUS_LU); + break; + case e1000_media_type_internal_serdes: + e1000_check_for_link(hw); + link_active = hw->serdes_has_link; + break; + default: + break; + } + + return link_active; +} + /** * e1000_watchdog - Timer Call-back * @data: pointer to adapter cast into an unsigned long @@ -2538,33 +2296,16 @@ static void e1000_watchdog(unsigned long data) struct net_device *netdev = adapter->netdev; struct e1000_tx_ring *txdr = adapter->tx_ring; u32 link, tctl; - s32 ret_val; - - ret_val = e1000_check_for_link(hw); - if ((ret_val == E1000_ERR_PHY) && - (hw->phy_type == e1000_phy_igp_3) && - (er32(CTRL) & E1000_PHY_CTRL_GBE_DISABLE)) { - /* See e1000_kumeran_lock_loss_workaround() */ - DPRINTK(LINK, INFO, - "Gigabit has been disabled, downgrading speed\n"); - } - if (hw->mac_type == e1000_82573) { - e1000_enable_tx_pkt_filtering(hw); - if (adapter->mng_vlan_id != hw->mng_cookie.vlan_id) - e1000_update_mng_vlan(adapter); - } - - if ((hw->media_type == e1000_media_type_internal_serdes) && - !(er32(TXCW) & E1000_TXCW_ANE)) - link = !hw->serdes_link_down; - else - link = er32(STATUS) & E1000_STATUS_LU; + link = e1000_has_link(adapter); + if ((netif_carrier_ok(netdev)) && link) + goto link_up; if (link) { if (!netif_carrier_ok(netdev)) { u32 ctrl; bool txb2b = true; + /* update snapshot of PHY registers on LSC */ e1000_get_speed_and_duplex(hw, &adapter->link_speed, &adapter->link_duplex); @@ -2589,7 +2330,7 @@ static void e1000_watchdog(unsigned long data) case SPEED_10: txb2b = false; netdev->tx_queue_len = 10; - adapter->tx_timeout_factor = 8; + adapter->tx_timeout_factor = 16; break; case SPEED_100: txb2b = false; @@ -2598,52 +2339,16 @@ static void e1000_watchdog(unsigned long data) break; } - if ((hw->mac_type == e1000_82571 || - hw->mac_type == e1000_82572) && - !txb2b) { - u32 tarc0; - tarc0 = er32(TARC0); - tarc0 &= ~(1 << 21); - ew32(TARC0, tarc0); - } - - /* disable TSO for pcie and 10/100 speeds, to avoid - * some hardware issues */ - if (!adapter->tso_force && - hw->bus_type == e1000_bus_type_pci_express){ - switch (adapter->link_speed) { - case SPEED_10: - case SPEED_100: - DPRINTK(PROBE,INFO, - "10/100 speed: disabling TSO\n"); - netdev->features &= ~NETIF_F_TSO; - netdev->features &= ~NETIF_F_TSO6; - break; - case SPEED_1000: - netdev->features |= NETIF_F_TSO; - netdev->features |= NETIF_F_TSO6; - break; - default: - /* oops */ - break; - } - } - - /* enable transmits in the hardware, need to do this - * after setting TARC0 */ + /* enable transmits in the hardware */ tctl = er32(TCTL); tctl |= E1000_TCTL_EN; ew32(TCTL, tctl); netif_carrier_on(netdev); - mod_timer(&adapter->phy_info_timer, round_jiffies(jiffies + 2 * HZ)); + if (!test_bit(__E1000_DOWN, &adapter->flags)) + mod_timer(&adapter->phy_info_timer, + round_jiffies(jiffies + 2 * HZ)); adapter->smartspeed = 0; - } else { - /* make sure the receive unit is started */ - if (hw->rx_needs_kicking) { - u32 rctl = er32(RCTL); - ew32(RCTL, rctl | E1000_RCTL_EN); - } } } else { if (netif_carrier_ok(netdev)) { @@ -2652,21 +2357,16 @@ static void e1000_watchdog(unsigned long data) printk(KERN_INFO "e1000: %s NIC Link is Down\n", netdev->name); netif_carrier_off(netdev); - mod_timer(&adapter->phy_info_timer, round_jiffies(jiffies + 2 * HZ)); - - /* 80003ES2LAN workaround-- - * For packet buffer work-around on link down event; - * disable receives in the ISR and - * reset device here in the watchdog - */ - if (hw->mac_type == e1000_80003es2lan) - /* reset device */ - schedule_work(&adapter->reset_task); + + if (!test_bit(__E1000_DOWN, &adapter->flags)) + mod_timer(&adapter->phy_info_timer, + round_jiffies(jiffies + 2 * HZ)); } e1000_smartspeed(adapter); } +link_up: e1000_update_stats(adapter); hw->tx_packet_delta = adapter->stats.tpt - adapter->tpt_old; @@ -2700,13 +2400,10 @@ static void e1000_watchdog(unsigned long data) /* Force detection of hung controller every watchdog period */ adapter->detect_tx_hung = true; - /* With 82571 controllers, LAA may be overwritten due to controller - * reset from the other port. Set the appropriate LAA in RAR[0] */ - if (hw->mac_type == e1000_82571 && hw->laa_is_present) - e1000_rar_set(hw, hw->mac_addr, 0); - /* Reset the timer */ - mod_timer(&adapter->watchdog_timer, round_jiffies(jiffies + 2 * HZ)); + if (!test_bit(__E1000_DOWN, &adapter->flags)) + mod_timer(&adapter->watchdog_timer, + round_jiffies(jiffies + 2 * HZ)); } enum latency_range { @@ -2718,6 +2415,11 @@ enum latency_range { /** * e1000_update_itr - update the dynamic ITR value based on statistics + * @adapter: pointer to adapter + * @itr_setting: current adapter->itr + * @packets: the number of packets during this measurement interval + * @bytes: the number of bytes during this measurement interval + * * Stores a new ITR value based on packets and byte * counts during the last interrupt. The advantage of per interrupt * computation is faster updates and more accurate ITR for the current @@ -2727,10 +2429,6 @@ enum latency_range { * while increasing bulk throughput. * this functionality is controlled by the InterruptThrottleRate module * parameter (see e1000_param.c) - * @adapter: pointer to adapter - * @itr_setting: current adapter->itr - * @packets: the number of packets during this measurement interval - * @bytes: the number of bytes during this measurement interval **/ static unsigned int e1000_update_itr(struct e1000_adapter *adapter, u16 itr_setting, int packets, int bytes) @@ -3035,8 +2733,9 @@ static int e1000_tx_map(struct e1000_adapter *adapter, size -= 4; buffer_info->length = size; - buffer_info->dma = skb_shinfo(skb)->dma_head + offset; + /* set time_stamp *before* dma to help avoid a possible race */ buffer_info->time_stamp = jiffies; + buffer_info->dma = skb_shinfo(skb)->dma_head + offset; buffer_info->next_to_watch = i; len -= size; @@ -3071,13 +2770,14 @@ static int e1000_tx_map(struct e1000_adapter *adapter, * Avoid terminating buffers within evenly-aligned * dwords. */ if (unlikely(adapter->pcix_82544 && - !((unsigned long)(frag->page+offset+size-1) & 4) && - size > 4)) + !((unsigned long)(page_to_phys(frag->page) + offset + + size - 1) & 4) && + size > 4)) size -= 4; buffer_info->length = size; - buffer_info->dma = map[f] + offset; buffer_info->time_stamp = jiffies; + buffer_info->dma = map[f] + offset; buffer_info->next_to_watch = i; len -= size; @@ -3186,41 +2886,6 @@ no_fifo_stall_required: return 0; } -#define MINIMUM_DHCP_PACKET_SIZE 282 -static int e1000_transfer_dhcp_info(struct e1000_adapter *adapter, - struct sk_buff *skb) -{ - struct e1000_hw *hw = &adapter->hw; - u16 length, offset; - if (vlan_tx_tag_present(skb)) { - if (!((vlan_tx_tag_get(skb) == hw->mng_cookie.vlan_id) && - ( hw->mng_cookie.status & - E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT)) ) - return 0; - } - if (skb->len > MINIMUM_DHCP_PACKET_SIZE) { - struct ethhdr *eth = (struct ethhdr *)skb->data; - if ((htons(ETH_P_IP) == eth->h_proto)) { - const struct iphdr *ip = - (struct iphdr *)((u8 *)skb->data+14); - if (IPPROTO_UDP == ip->protocol) { - struct udphdr *udp = - (struct udphdr *)((u8 *)ip + - (ip->ihl << 2)); - if (ntohs(udp->dest) == 67) { - offset = (u8 *)udp + 8 - skb->data; - length = skb->len - offset; - - return e1000_mng_write_dhcp_info(hw, - (u8 *)udp + 8, - length); - } - } - } - } - return 0; -} - static int __e1000_maybe_stop_tx(struct net_device *netdev, int size) { struct e1000_adapter *adapter = netdev_priv(netdev); @@ -3279,11 +2944,6 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, return NETDEV_TX_OK; } - /* 82571 and newer doesn't need the workaround that limited descriptor - * length to 4kB */ - if (hw->mac_type >= e1000_82571) - max_per_txd = 8192; - mss = skb_shinfo(skb)->gso_size; /* The controller does a simple calculation to * make sure there is enough room in the FIFO before @@ -3296,9 +2956,6 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, max_per_txd = min(mss << 2, max_per_txd); max_txd_pwr = fls(max_per_txd) - 1; - /* TSO Workaround for 82571/2/3 Controllers -- if skb->data - * points to just header, pull a few bytes of payload from - * frags into skb->data */ hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb); if (skb->data_len && hdr_len == len) { switch (hw->mac_type) { @@ -3313,10 +2970,6 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, if ((unsigned long)(skb_tail_pointer(skb) - 1) & 4) break; /* fall through */ - case e1000_82571: - case e1000_82572: - case e1000_82573: - case e1000_ich8lan: pull_size = min((unsigned int)4, skb->data_len); if (!__pskb_pull_tail(skb, pull_size)) { DPRINTK(DRV, ERR, @@ -3361,11 +3014,6 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, if (adapter->pcix_82544) count += nr_frags; - - if (hw->tx_pkt_filtering && - (hw->mac_type == e1000_82573)) - e1000_transfer_dhcp_info(adapter, skb); - /* need: count + 2 desc gap to keep tail from touching * head, otherwise try next time */ if (unlikely(e1000_maybe_stop_tx(netdev, tx_ring, count + 2))) @@ -3374,7 +3022,9 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, if (unlikely(hw->mac_type == e1000_82547)) { if (unlikely(e1000_82547_fifo_workaround(adapter, skb))) { netif_stop_queue(netdev); - mod_timer(&adapter->tx_fifo_stall_timer, jiffies + 1); + if (!test_bit(__E1000_DOWN, &adapter->flags)) + mod_timer(&adapter->tx_fifo_stall_timer, + jiffies + 1); return NETDEV_TX_BUSY; } } @@ -3393,14 +3043,12 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, } if (likely(tso)) { - tx_ring->last_tx_tso = 1; + if (likely(hw->mac_type != e1000_82544)) + tx_ring->last_tx_tso = 1; tx_flags |= E1000_TX_FLAGS_TSO; } else if (likely(e1000_tx_csum(adapter, tx_ring, skb))) tx_flags |= E1000_TX_FLAGS_CSUM; - /* Old method was to assume IPv4 packet by default if TSO was enabled. - * 82571 hardware supports TSO capabilities for IPv6 as well... - * no longer assume, we must. */ if (likely(skb->protocol == htons(ETH_P_IP))) tx_flags |= E1000_TX_FLAGS_IPV4; @@ -3472,7 +3120,6 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) struct e1000_adapter *adapter = netdev_priv(netdev); struct e1000_hw *hw = &adapter->hw; int max_frame = new_mtu + ENET_HEADER_SIZE + ETHERNET_FCS_SIZE; - u16 eeprom_data = 0; if ((max_frame < MINIMUM_ETHERNET_FRAME_SIZE) || (max_frame > MAX_JUMBO_FRAME_SIZE)) { @@ -3483,44 +3130,23 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) /* Adapter-specific max frame size limits. */ switch (hw->mac_type) { case e1000_undefined ... e1000_82542_rev2_1: - case e1000_ich8lan: if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) { DPRINTK(PROBE, ERR, "Jumbo Frames not supported.\n"); return -EINVAL; } break; - case e1000_82573: - /* Jumbo Frames not supported if: - * - this is not an 82573L device - * - ASPM is enabled in any way (0x1A bits 3:2) */ - e1000_read_eeprom(hw, EEPROM_INIT_3GIO_3, 1, - &eeprom_data); - if ((hw->device_id != E1000_DEV_ID_82573L) || - (eeprom_data & EEPROM_WORD1A_ASPM_MASK)) { - if (max_frame > (ETH_FRAME_LEN + ETH_FCS_LEN)) { - DPRINTK(PROBE, ERR, - "Jumbo Frames not supported.\n"); - return -EINVAL; - } - break; - } - /* ERT will be enabled later to enable wire speed receives */ - - /* fall through to get support */ - case e1000_82571: - case e1000_82572: - case e1000_80003es2lan: -#define MAX_STD_JUMBO_FRAME_SIZE 9234 - if (max_frame > MAX_STD_JUMBO_FRAME_SIZE) { - DPRINTK(PROBE, ERR, "MTU > 9216 not supported.\n"); - return -EINVAL; - } - break; default: /* Capable of supporting up to MAX_JUMBO_FRAME_SIZE limit. */ break; } + while (test_and_set_bit(__E1000_RESETTING, &adapter->flags)) + msleep(1); + /* e1000_down has a dependency on max_frame_size */ + hw->max_frame_size = max_frame; + if (netif_running(netdev)) + e1000_down(adapter); + /* NOTE: netdev_alloc_skb reserves 16 bytes, and typically NET_IP_ALIGN * means we reserve 2 more, this pushes us to allocate from the next * larger slab size. @@ -3549,11 +3175,16 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) (max_frame == MAXIMUM_ETHERNET_VLAN_SIZE))) adapter->rx_buffer_len = MAXIMUM_ETHERNET_VLAN_SIZE; + printk(KERN_INFO "e1000: %s changing MTU from %d to %d\n", + netdev->name, netdev->mtu, new_mtu); netdev->mtu = new_mtu; - hw->max_frame_size = max_frame; if (netif_running(netdev)) - e1000_reinit_locked(adapter); + e1000_up(adapter); + else + e1000_reset(adapter); + + clear_bit(__E1000_RESETTING, &adapter->flags); return 0; } @@ -3596,14 +3227,12 @@ void e1000_update_stats(struct e1000_adapter *adapter) adapter->stats.mprc += er32(MPRC); adapter->stats.roc += er32(ROC); - if (hw->mac_type != e1000_ich8lan) { - adapter->stats.prc64 += er32(PRC64); - adapter->stats.prc127 += er32(PRC127); - adapter->stats.prc255 += er32(PRC255); - adapter->stats.prc511 += er32(PRC511); - adapter->stats.prc1023 += er32(PRC1023); - adapter->stats.prc1522 += er32(PRC1522); - } + adapter->stats.prc64 += er32(PRC64); + adapter->stats.prc127 += er32(PRC127); + adapter->stats.prc255 += er32(PRC255); + adapter->stats.prc511 += er32(PRC511); + adapter->stats.prc1023 += er32(PRC1023); + adapter->stats.prc1522 += er32(PRC1522); adapter->stats.symerrs += er32(SYMERRS); adapter->stats.mpc += er32(MPC); @@ -3632,14 +3261,12 @@ void e1000_update_stats(struct e1000_adapter *adapter) adapter->stats.toth += er32(TOTH); adapter->stats.tpr += er32(TPR); - if (hw->mac_type != e1000_ich8lan) { - adapter->stats.ptc64 += er32(PTC64); - adapter->stats.ptc127 += er32(PTC127); - adapter->stats.ptc255 += er32(PTC255); - adapter->stats.ptc511 += er32(PTC511); - adapter->stats.ptc1023 += er32(PTC1023); - adapter->stats.ptc1522 += er32(PTC1522); - } + adapter->stats.ptc64 += er32(PTC64); + adapter->stats.ptc127 += er32(PTC127); + adapter->stats.ptc255 += er32(PTC255); + adapter->stats.ptc511 += er32(PTC511); + adapter->stats.ptc1023 += er32(PTC1023); + adapter->stats.ptc1522 += er32(PTC1522); adapter->stats.mptc += er32(MPTC); adapter->stats.bptc += er32(BPTC); @@ -3659,20 +3286,6 @@ void e1000_update_stats(struct e1000_adapter *adapter) adapter->stats.tsctc += er32(TSCTC); adapter->stats.tsctfc += er32(TSCTFC); } - if (hw->mac_type > e1000_82547_rev_2) { - adapter->stats.iac += er32(IAC); - adapter->stats.icrxoc += er32(ICRXOC); - - if (hw->mac_type != e1000_ich8lan) { - adapter->stats.icrxptc += er32(ICRXPTC); - adapter->stats.icrxatc += er32(ICRXATC); - adapter->stats.ictxptc += er32(ICTXPTC); - adapter->stats.ictxatc += er32(ICTXATC); - adapter->stats.ictxqec += er32(ICTXQEC); - adapter->stats.ictxqmtc += er32(ICTXQMTC); - adapter->stats.icrxdmtc += er32(ICRXDMTC); - } - } /* Fill out the OS statistics structure */ adapter->net_stats.multicast = adapter->stats.mprc; @@ -3731,49 +3344,6 @@ void e1000_update_stats(struct e1000_adapter *adapter) } /** - * e1000_intr_msi - Interrupt Handler - * @irq: interrupt number - * @data: pointer to a network interface device structure - **/ - -static irqreturn_t e1000_intr_msi(int irq, void *data) -{ - struct net_device *netdev = data; - struct e1000_adapter *adapter = netdev_priv(netdev); - struct e1000_hw *hw = &adapter->hw; - u32 icr = er32(ICR); - - /* in NAPI mode read ICR disables interrupts using IAM */ - - if (icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC)) { - hw->get_link_status = 1; - /* 80003ES2LAN workaround-- For packet buffer work-around on - * link down event; disable receives here in the ISR and reset - * adapter in watchdog */ - if (netif_carrier_ok(netdev) && - (hw->mac_type == e1000_80003es2lan)) { - /* disable receives */ - u32 rctl = er32(RCTL); - ew32(RCTL, rctl & ~E1000_RCTL_EN); - } - /* guard against interrupt when we're going down */ - if (!test_bit(__E1000_DOWN, &adapter->flags)) - mod_timer(&adapter->watchdog_timer, jiffies + 1); - } - - if (likely(napi_schedule_prep(&adapter->napi))) { - adapter->total_tx_bytes = 0; - adapter->total_tx_packets = 0; - adapter->total_rx_bytes = 0; - adapter->total_rx_packets = 0; - __napi_schedule(&adapter->napi); - } else - e1000_irq_enable(adapter); - - return IRQ_HANDLED; -} - -/** * e1000_intr - Interrupt Handler * @irq: interrupt number * @data: pointer to a network interface device structure @@ -3784,43 +3354,22 @@ static irqreturn_t e1000_intr(int irq, void *data) struct net_device *netdev = data; struct e1000_adapter *adapter = netdev_priv(netdev); struct e1000_hw *hw = &adapter->hw; - u32 rctl, icr = er32(ICR); + u32 icr = er32(ICR); if (unlikely((!icr) || test_bit(__E1000_DOWN, &adapter->flags))) return IRQ_NONE; /* Not our interrupt */ - /* IMS will not auto-mask if INT_ASSERTED is not set, and if it is - * not set, then the adapter didn't send an interrupt */ - if (unlikely(hw->mac_type >= e1000_82571 && - !(icr & E1000_ICR_INT_ASSERTED))) - return IRQ_NONE; - - /* Interrupt Auto-Mask...upon reading ICR, interrupts are masked. No - * need for the IMC write */ - if (unlikely(icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))) { hw->get_link_status = 1; - /* 80003ES2LAN workaround-- - * For packet buffer work-around on link down event; - * disable receives here in the ISR and - * reset adapter in watchdog - */ - if (netif_carrier_ok(netdev) && - (hw->mac_type == e1000_80003es2lan)) { - /* disable receives */ - rctl = er32(RCTL); - ew32(RCTL, rctl & ~E1000_RCTL_EN); - } /* guard against interrupt when we're going down */ if (!test_bit(__E1000_DOWN, &adapter->flags)) mod_timer(&adapter->watchdog_timer, jiffies + 1); } - if (unlikely(hw->mac_type < e1000_82571)) { - /* disable interrupts, without the synchronize_irq bit */ - ew32(IMC, ~0); - E1000_WRITE_FLUSH(); - } + /* disable interrupts, without the synchronize_irq bit */ + ew32(IMC, ~0); + E1000_WRITE_FLUSH(); + if (likely(napi_schedule_prep(&adapter->napi))) { adapter->total_tx_bytes = 0; adapter->total_tx_packets = 0; @@ -3844,17 +3393,13 @@ static irqreturn_t e1000_intr(int irq, void *data) static int e1000_clean(struct napi_struct *napi, int budget) { struct e1000_adapter *adapter = container_of(napi, struct e1000_adapter, napi); - struct net_device *poll_dev = adapter->netdev; - int tx_cleaned = 0, work_done = 0; - - adapter = netdev_priv(poll_dev); + int tx_clean_complete = 0, work_done = 0; - tx_cleaned = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]); + tx_clean_complete = e1000_clean_tx_irq(adapter, &adapter->tx_ring[0]); - adapter->clean_rx(adapter, &adapter->rx_ring[0], - &work_done, budget); + adapter->clean_rx(adapter, &adapter->rx_ring[0], &work_done, budget); - if (!tx_cleaned) + if (!tx_clean_complete) work_done = budget; /* If budget not fully consumed, exit the polling mode */ @@ -3925,7 +3470,9 @@ static bool e1000_clean_tx_irq(struct e1000_adapter *adapter, * sees the new next_to_clean. */ smp_mb(); - if (netif_queue_stopped(netdev)) { + + if (netif_queue_stopped(netdev) && + !(test_bit(__E1000_DOWN, &adapter->flags))) { netif_wake_queue(netdev); ++adapter->restart_queue; } @@ -3935,8 +3482,8 @@ static bool e1000_clean_tx_irq(struct e1000_adapter *adapter, /* Detect a transmit hang in hardware, this serializes the * check with the clearing of time_stamp and movement of i */ adapter->detect_tx_hung = false; - if (tx_ring->buffer_info[i].time_stamp && - time_after(jiffies, tx_ring->buffer_info[i].time_stamp + + if (tx_ring->buffer_info[eop].time_stamp && + time_after(jiffies, tx_ring->buffer_info[eop].time_stamp + (adapter->tx_timeout_factor * HZ)) && !(er32(STATUS) & E1000_STATUS_TXOFF)) { @@ -3958,7 +3505,7 @@ static bool e1000_clean_tx_irq(struct e1000_adapter *adapter, readl(hw->hw_addr + tx_ring->tdt), tx_ring->next_to_use, tx_ring->next_to_clean, - tx_ring->buffer_info[i].time_stamp, + tx_ring->buffer_info[eop].time_stamp, eop, jiffies, eop_desc->upper.fields.status); @@ -3999,25 +3546,13 @@ static void e1000_rx_checksum(struct e1000_adapter *adapter, u32 status_err, return; } /* TCP/UDP Checksum has not been calculated */ - if (hw->mac_type <= e1000_82547_rev_2) { - if (!(status & E1000_RXD_STAT_TCPCS)) - return; - } else { - if (!(status & (E1000_RXD_STAT_TCPCS | E1000_RXD_STAT_UDPCS))) - return; - } + if (!(status & E1000_RXD_STAT_TCPCS)) + return; + /* It must be a TCP or UDP packet with a valid checksum */ if (likely(status & E1000_RXD_STAT_TCPCS)) { /* TCP checksum is good */ skb->ip_summed = CHECKSUM_UNNECESSARY; - } else if (hw->mac_type > e1000_82547_rev_2) { - /* IP fragment with UDP payload */ - /* Hardware complements the payload checksum, so we undo it - * and then put the value in host order for further stack use. - */ - __sum16 sum = (__force __sum16)htons(csum); - skb->csum = csum_unfold(~sum); - skb->ip_summed = CHECKSUM_COMPLETE; } adapter->hw_csum_good++; } @@ -4814,20 +4349,6 @@ void e1000_pcix_set_mmrbc(struct e1000_hw *hw, int mmrbc) pcix_set_mmrbc(adapter->pdev, mmrbc); } -s32 e1000_read_pcie_cap_reg(struct e1000_hw *hw, u32 reg, u16 *value) -{ - struct e1000_adapter *adapter = hw->back; - u16 cap_offset; - - cap_offset = pci_find_capability(adapter->pdev, PCI_CAP_ID_EXP); - if (!cap_offset) - return -E1000_ERR_CONFIG; - - pci_read_config_word(adapter->pdev, cap_offset + reg, value); - - return E1000_SUCCESS; -} - void e1000_io_write(struct e1000_hw *hw, unsigned long port, u32 value) { outl(value, port); @@ -4850,33 +4371,27 @@ static void e1000_vlan_rx_register(struct net_device *netdev, ctrl |= E1000_CTRL_VME; ew32(CTRL, ctrl); - if (adapter->hw.mac_type != e1000_ich8lan) { - /* enable VLAN receive filtering */ - rctl = er32(RCTL); - rctl &= ~E1000_RCTL_CFIEN; - if (!(netdev->flags & IFF_PROMISC)) - rctl |= E1000_RCTL_VFE; - ew32(RCTL, rctl); - e1000_update_mng_vlan(adapter); - } + /* enable VLAN receive filtering */ + rctl = er32(RCTL); + rctl &= ~E1000_RCTL_CFIEN; + if (!(netdev->flags & IFF_PROMISC)) + rctl |= E1000_RCTL_VFE; + ew32(RCTL, rctl); + e1000_update_mng_vlan(adapter); } else { /* disable VLAN tag insert/strip */ ctrl = er32(CTRL); ctrl &= ~E1000_CTRL_VME; ew32(CTRL, ctrl); - if (adapter->hw.mac_type != e1000_ich8lan) { - /* disable VLAN receive filtering */ - rctl = er32(RCTL); - rctl &= ~E1000_RCTL_VFE; - ew32(RCTL, rctl); + /* disable VLAN receive filtering */ + rctl = er32(RCTL); + rctl &= ~E1000_RCTL_VFE; + ew32(RCTL, rctl); - if (adapter->mng_vlan_id != - (u16)E1000_MNG_VLAN_NONE) { - e1000_vlan_rx_kill_vid(netdev, - adapter->mng_vlan_id); - adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; - } + if (adapter->mng_vlan_id != (u16)E1000_MNG_VLAN_NONE) { + e1000_vlan_rx_kill_vid(netdev, adapter->mng_vlan_id); + adapter->mng_vlan_id = E1000_MNG_VLAN_NONE; } } @@ -4913,14 +4428,6 @@ static void e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid) if (!test_bit(__E1000_DOWN, &adapter->flags)) e1000_irq_enable(adapter); - if ((hw->mng_cookie.status & - E1000_MNG_DHCP_COOKIE_STATUS_VLAN_SUPPORT) && - (vid == adapter->mng_vlan_id)) { - /* release control to f/w */ - e1000_release_hw_control(adapter); - return; - } - /* remove VID from filter table */ index = (vid >> 5) & 0x7F; vfta = E1000_READ_REG_ARRAY(hw, VFTA, index); @@ -5031,16 +4538,13 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake) } if (hw->media_type == e1000_media_type_fiber || - hw->media_type == e1000_media_type_internal_serdes) { + hw->media_type == e1000_media_type_internal_serdes) { /* keep the laser running in D3 */ ctrl_ext = er32(CTRL_EXT); ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA; ew32(CTRL_EXT, ctrl_ext); } - /* Allow time for pending master requests to run */ - e1000_disable_pciex_master(hw); - ew32(WUC, E1000_WUC_PME_EN); ew32(WUFC, wufc); } else { @@ -5056,16 +4560,9 @@ static int __e1000_shutdown(struct pci_dev *pdev, bool *enable_wake) if (adapter->en_mng_pt) *enable_wake = true; - if (hw->phy_type == e1000_phy_igp_3) - e1000_phy_powerdown_workaround(hw); - if (netif_running(netdev)) e1000_free_irq(adapter); - /* Release control of h/w to f/w. If f/w is AMT enabled, this - * would have already happened in close and is redundant. */ - e1000_release_hw_control(adapter); - pci_disable_device(pdev); return 0; @@ -5131,14 +4628,6 @@ static int e1000_resume(struct pci_dev *pdev) netif_device_attach(netdev); - /* If the controller is 82573 and f/w is AMT, do not set - * DRV_LOAD until the interface is up. For all other cases, - * let the f/w know that the h/w is now under the control - * of the driver. */ - if (hw->mac_type != e1000_82573 || - !e1000_check_mng_mode(hw)) - e1000_get_hw_control(adapter); - return 0; } #endif @@ -5174,7 +4663,7 @@ static void e1000_netpoll(struct net_device *netdev) /** * e1000_io_error_detected - called when PCI error is detected * @pdev: Pointer to PCI device - * @state: The current pci conneection state + * @state: The current pci connection state * * This function is called after a PCI bus error affecting * this device has been detected. @@ -5243,7 +4732,6 @@ static void e1000_io_resume(struct pci_dev *pdev) { struct net_device *netdev = pci_get_drvdata(pdev); struct e1000_adapter *adapter = netdev_priv(netdev); - struct e1000_hw *hw = &adapter->hw; e1000_init_manageability(adapter); @@ -5255,15 +4743,6 @@ static void e1000_io_resume(struct pci_dev *pdev) } netif_device_attach(netdev); - - /* If the controller is 82573 and f/w is AMT, do not set - * DRV_LOAD until the interface is up. For all other cases, - * let the f/w know that the h/w is now under the control - * of the driver. */ - if (hw->mac_type != e1000_82573 || - !e1000_check_mng_mode(hw)) - e1000_get_hw_control(adapter); - } /* e1000_main.c */ diff --git a/drivers/net/e1000/e1000_param.c b/drivers/net/e1000/e1000_param.c index 213437d1315..38d2741ccae 100644 --- a/drivers/net/e1000/e1000_param.c +++ b/drivers/net/e1000/e1000_param.c @@ -518,22 +518,6 @@ void __devinit e1000_check_options(struct e1000_adapter *adapter) adapter->smart_power_down = opt.def; } } - { /* Kumeran Lock Loss Workaround */ - opt = (struct e1000_option) { - .type = enable_option, - .name = "Kumeran Lock Loss Workaround", - .err = "defaulting to Enabled", - .def = OPTION_ENABLED - }; - - if (num_KumeranLockLoss > bd) { - unsigned int kmrn_lock_loss = KumeranLockLoss[bd]; - e1000_validate_option(&kmrn_lock_loss, &opt, adapter); - adapter->hw.kmrn_lock_loss_workaround_disabled = !kmrn_lock_loss; - } else { - adapter->hw.kmrn_lock_loss_workaround_disabled = !opt.def; - } - } switch (adapter->hw.media_type) { case e1000_media_type_fiber: @@ -626,12 +610,6 @@ static void __devinit e1000_check_copper_options(struct e1000_adapter *adapter) .p = dplx_list }} }; - if (e1000_check_phy_reset_block(&adapter->hw)) { - DPRINTK(PROBE, INFO, - "Link active due to SoL/IDER Session. " - "Speed/Duplex/AutoNeg parameter ignored.\n"); - return; - } if (num_Duplex > bd) { dplx = Duplex[bd]; e1000_validate_option(&dplx, &opt, adapter); diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c index 977c3d35827..41bd7aeafd8 100644 --- a/drivers/net/ehea/ehea_main.c +++ b/drivers/net/ehea/ehea_main.c @@ -3083,7 +3083,6 @@ static const struct net_device_ops ehea_netdev_ops = { .ndo_poll_controller = ehea_netpoll, #endif .ndo_get_stats = ehea_get_stats, - .ndo_change_mtu = eth_change_mtu, .ndo_set_mac_address = ehea_set_mac_addr, .ndo_validate_addr = eth_validate_addr, .ndo_set_multicast_list = ehea_set_multicast_list, diff --git a/drivers/net/ehea/ehea_qmr.c b/drivers/net/ehea/ehea_qmr.c index 3747457f5e6..bc7c5b7abb8 100644 --- a/drivers/net/ehea/ehea_qmr.c +++ b/drivers/net/ehea/ehea_qmr.c @@ -751,7 +751,7 @@ int ehea_create_busmap(void) mutex_lock(&ehea_busmap_mutex); ehea_mr_len = 0; - ret = walk_memory_resource(0, 1ULL << MAX_PHYSMEM_BITS, NULL, + ret = walk_system_ram_range(0, 1ULL << MAX_PHYSMEM_BITS, NULL, ehea_create_busmap_callback); mutex_unlock(&ehea_busmap_mutex); return ret; diff --git a/drivers/net/enc28j60.c b/drivers/net/enc28j60.c index 117fc6c12e3..66813c91a72 100644 --- a/drivers/net/enc28j60.c +++ b/drivers/net/enc28j60.c @@ -1666,3 +1666,4 @@ MODULE_AUTHOR("Claudio Lanconelli <lanconelli.claudio@eptar.com>"); MODULE_LICENSE("GPL"); module_param_named(debug, debug.msg_enable, int, 0); MODULE_PARM_DESC(debug, "Debug verbosity level (0=none, ..., ffff=all)"); +MODULE_ALIAS("spi:" DRV_NAME); diff --git a/drivers/net/fec.c b/drivers/net/fec.c index b47201874d8..29234380e6c 100644 --- a/drivers/net/fec.c +++ b/drivers/net/fec.c @@ -1154,19 +1154,9 @@ static void __inline__ fec_request_mii_intr(struct net_device *dev) printk("FEC: Could not allocate fec(MII) IRQ(66)!\n"); } -static void __inline__ fec_disable_phy_intr(void) +static void __inline__ fec_disable_phy_intr(struct net_device *dev) { - volatile unsigned long *icrp; - icrp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_ICR1); - *icrp = 0x08000000; -} - -static void __inline__ fec_phy_ack_intr(void) -{ - volatile unsigned long *icrp; - /* Acknowledge the interrupt */ - icrp = (volatile unsigned long *) (MCF_MBAR + MCFSIM_ICR1); - *icrp = 0x0d000000; + free_irq(66, dev); } #endif @@ -1398,7 +1388,7 @@ mii_discover_phy(uint mii_reg, struct net_device *dev) writel(0, fep->hwp + FEC_MII_SPEED); fep->phy_speed = 0; #ifdef HAVE_mii_link_interrupt - fec_disable_phy_intr(); + fec_disable_phy_intr(dev); #endif } } @@ -1411,8 +1401,6 @@ mii_link_interrupt(int irq, void * dev_id) struct net_device *dev = dev_id; struct fec_enet_private *fep = netdev_priv(dev); - fec_phy_ack_intr(); - mii_do_cmd(dev, fep->phy->ack_int); mii_do_cmd(dev, phy_cmd_relink); /* restart and display status */ diff --git a/drivers/net/gianfar_ethtool.c b/drivers/net/gianfar_ethtool.c index 2234118eedb..6c144b525b4 100644 --- a/drivers/net/gianfar_ethtool.c +++ b/drivers/net/gianfar_ethtool.c @@ -293,7 +293,7 @@ static int gfar_gcoalesce(struct net_device *dev, struct ethtool_coalesce *cvals rxtime = get_ictt_value(priv->rxic); rxcount = get_icft_value(priv->rxic); txtime = get_ictt_value(priv->txic); - txcount = get_icft_value(priv->txic);; + txcount = get_icft_value(priv->txic); cvals->rx_coalesce_usecs = gfar_ticks2usecs(priv, rxtime); cvals->rx_max_coalesced_frames = rxcount; diff --git a/drivers/net/ibm_newemac/core.c b/drivers/net/ibm_newemac/core.c index 1d7d7fef414..89c82c5e63e 100644 --- a/drivers/net/ibm_newemac/core.c +++ b/drivers/net/ibm_newemac/core.c @@ -2556,13 +2556,13 @@ static int __devinit emac_init_config(struct emac_instance *dev) if (emac_read_uint_prop(np, "mdio-device", &dev->mdio_ph, 0)) dev->mdio_ph = 0; if (emac_read_uint_prop(np, "zmii-device", &dev->zmii_ph, 0)) - dev->zmii_ph = 0;; + dev->zmii_ph = 0; if (emac_read_uint_prop(np, "zmii-channel", &dev->zmii_port, 0)) - dev->zmii_port = 0xffffffff;; + dev->zmii_port = 0xffffffff; if (emac_read_uint_prop(np, "rgmii-device", &dev->rgmii_ph, 0)) - dev->rgmii_ph = 0;; + dev->rgmii_ph = 0; if (emac_read_uint_prop(np, "rgmii-channel", &dev->rgmii_port, 0)) - dev->rgmii_port = 0xffffffff;; + dev->rgmii_port = 0xffffffff; if (emac_read_uint_prop(np, "fifo-entry-size", &dev->fifo_entry_size, 0)) dev->fifo_entry_size = 16; if (emac_read_uint_prop(np, "mal-burst-size", &dev->mal_burst_size, 0)) diff --git a/drivers/net/igb/e1000_82575.c b/drivers/net/igb/e1000_82575.c index 6158c0f3b20..f8f5772557c 100644 --- a/drivers/net/igb/e1000_82575.c +++ b/drivers/net/igb/e1000_82575.c @@ -49,11 +49,10 @@ static s32 igb_read_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16 *); static s32 igb_reset_hw_82575(struct e1000_hw *); static s32 igb_set_d0_lplu_state_82575(struct e1000_hw *, bool); static s32 igb_setup_copper_link_82575(struct e1000_hw *); -static s32 igb_setup_fiber_serdes_link_82575(struct e1000_hw *); +static s32 igb_setup_serdes_link_82575(struct e1000_hw *); static s32 igb_write_phy_reg_sgmii_82575(struct e1000_hw *, u32, u16); static void igb_clear_hw_cntrs_82575(struct e1000_hw *); static s32 igb_acquire_swfw_sync_82575(struct e1000_hw *, u16); -static void igb_configure_pcs_link_82575(struct e1000_hw *); static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *, u16 *, u16 *); static s32 igb_get_phy_id_82575(struct e1000_hw *); @@ -105,16 +104,20 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw) dev_spec->sgmii_active = false; ctrl_ext = rd32(E1000_CTRL_EXT); - if ((ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) == - E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES) { - hw->phy.media_type = e1000_media_type_internal_serdes; - ctrl_ext |= E1000_CTRL_I2C_ENA; - } else if (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_SGMII) { + switch (ctrl_ext & E1000_CTRL_EXT_LINK_MODE_MASK) { + case E1000_CTRL_EXT_LINK_MODE_SGMII: dev_spec->sgmii_active = true; ctrl_ext |= E1000_CTRL_I2C_ENA; - } else { + break; + case E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES: + hw->phy.media_type = e1000_media_type_internal_serdes; + ctrl_ext |= E1000_CTRL_I2C_ENA; + break; + default: ctrl_ext &= ~E1000_CTRL_I2C_ENA; + break; } + wr32(E1000_CTRL_EXT, ctrl_ext); /* Set mta register count */ @@ -134,7 +137,7 @@ static s32 igb_get_invariants_82575(struct e1000_hw *hw) mac->ops.setup_physical_interface = (hw->phy.media_type == e1000_media_type_copper) ? igb_setup_copper_link_82575 - : igb_setup_fiber_serdes_link_82575; + : igb_setup_serdes_link_82575; /* NVM initialization */ eecd = rd32(E1000_EECD); @@ -379,6 +382,7 @@ static s32 igb_get_phy_id_82575(struct e1000_hw *hw) struct e1000_phy_info *phy = &hw->phy; s32 ret_val = 0; u16 phy_id; + u32 ctrl_ext; /* * For SGMII PHYs, we try the list of possible addresses until @@ -393,6 +397,12 @@ static s32 igb_get_phy_id_82575(struct e1000_hw *hw) goto out; } + /* Power on sgmii phy if it is disabled */ + ctrl_ext = rd32(E1000_CTRL_EXT); + wr32(E1000_CTRL_EXT, ctrl_ext & ~E1000_CTRL_EXT_SDP3_DATA); + wrfl(); + msleep(300); + /* * The address field in the I2CCMD register is 3 bits and 0 is invalid. * Therefore, we need to test 1-7 @@ -418,9 +428,12 @@ static s32 igb_get_phy_id_82575(struct e1000_hw *hw) phy->addr = 0; ret_val = -E1000_ERR_PHY; goto out; + } else { + ret_val = igb_get_phy_id(hw); } - ret_val = igb_get_phy_id(hw); + /* restore previous sfp cage power state */ + wr32(E1000_CTRL_EXT, ctrl_ext); out: return ret_val; @@ -766,17 +779,18 @@ static s32 igb_get_pcs_speed_and_duplex_82575(struct e1000_hw *hw, u16 *speed, } /** - * igb_shutdown_fiber_serdes_link_82575 - Remove link during power down + * igb_shutdown_serdes_link_82575 - Remove link during power down * @hw: pointer to the HW structure * * In the case of fiber serdes, shut down optics and PCS on driver unload * when management pass thru is not enabled. **/ -void igb_shutdown_fiber_serdes_link_82575(struct e1000_hw *hw) +void igb_shutdown_serdes_link_82575(struct e1000_hw *hw) { u32 reg; - if (hw->phy.media_type != e1000_media_type_internal_serdes) + if (hw->phy.media_type != e1000_media_type_internal_serdes || + igb_sgmii_active_82575(hw)) return; /* if the management interface is not enabled, then power down */ @@ -788,7 +802,7 @@ void igb_shutdown_fiber_serdes_link_82575(struct e1000_hw *hw) /* shutdown the laser */ reg = rd32(E1000_CTRL_EXT); - reg |= E1000_CTRL_EXT_SDP7_DATA; + reg |= E1000_CTRL_EXT_SDP3_DATA; wr32(E1000_CTRL_EXT, reg); /* flush the write to verify completion */ @@ -927,6 +941,17 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw) ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX); wr32(E1000_CTRL, ctrl); + ret_val = igb_setup_serdes_link_82575(hw); + if (ret_val) + goto out; + + if (igb_sgmii_active_82575(hw) && !hw->phy.reset_disable) { + ret_val = hw->phy.ops.reset(hw); + if (ret_val) { + hw_dbg("Error resetting the PHY.\n"); + goto out; + } + } switch (hw->phy.type) { case e1000_phy_m88: ret_val = igb_copper_link_setup_m88(hw); @@ -963,8 +988,6 @@ static s32 igb_setup_copper_link_82575(struct e1000_hw *hw) } } - igb_configure_pcs_link_82575(hw); - /* * Check link status. Wait up to 100 microseconds for link to become * valid. @@ -987,14 +1010,18 @@ out: } /** - * igb_setup_fiber_serdes_link_82575 - Setup link for fiber/serdes + * igb_setup_serdes_link_82575 - Setup link for fiber/serdes * @hw: pointer to the HW structure * * Configures speed and duplex for fiber and serdes links. **/ -static s32 igb_setup_fiber_serdes_link_82575(struct e1000_hw *hw) +static s32 igb_setup_serdes_link_82575(struct e1000_hw *hw) { - u32 reg; + u32 ctrl_reg, reg; + + if ((hw->phy.media_type != e1000_media_type_internal_serdes) && + !igb_sgmii_active_82575(hw)) + return 0; /* * On the 82575, SerDes loopback mode persists until it is @@ -1004,26 +1031,38 @@ static s32 igb_setup_fiber_serdes_link_82575(struct e1000_hw *hw) */ wr32(E1000_SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK); - /* Force link up, set 1gb, set both sw defined pins */ - reg = rd32(E1000_CTRL); - reg |= E1000_CTRL_SLU | - E1000_CTRL_SPD_1000 | - E1000_CTRL_FRCSPD | - E1000_CTRL_SWDPIN0 | - E1000_CTRL_SWDPIN1; - wr32(E1000_CTRL, reg); - - /* Power on phy for 82576 fiber adapters */ - if (hw->mac.type == e1000_82576) { - reg = rd32(E1000_CTRL_EXT); - reg &= ~E1000_CTRL_EXT_SDP7_DATA; - wr32(E1000_CTRL_EXT, reg); + /* power on the sfp cage if present */ + reg = rd32(E1000_CTRL_EXT); + reg &= ~E1000_CTRL_EXT_SDP3_DATA; + wr32(E1000_CTRL_EXT, reg); + + ctrl_reg = rd32(E1000_CTRL); + ctrl_reg |= E1000_CTRL_SLU; + + if (hw->mac.type == e1000_82575 || hw->mac.type == e1000_82576) { + /* set both sw defined pins */ + ctrl_reg |= E1000_CTRL_SWDPIN0 | E1000_CTRL_SWDPIN1; + + /* Set switch control to serdes energy detect */ + reg = rd32(E1000_CONNSW); + reg |= E1000_CONNSW_ENRGSRC; + wr32(E1000_CONNSW, reg); + } + + reg = rd32(E1000_PCS_LCTL); + + if (igb_sgmii_active_82575(hw)) { + /* allow time for SFP cage to power up phy */ + msleep(300); + + /* AN time out should be disabled for SGMII mode */ + reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT); + } else { + ctrl_reg |= E1000_CTRL_SPD_1000 | E1000_CTRL_FRCSPD | + E1000_CTRL_FD | E1000_CTRL_FRCDPX; } - /* Set switch control to serdes energy detect */ - reg = rd32(E1000_CONNSW); - reg |= E1000_CONNSW_ENRGSRC; - wr32(E1000_CONNSW, reg); + wr32(E1000_CTRL, ctrl_reg); /* * New SerDes mode allows for forcing speed or autonegotiating speed @@ -1031,12 +1070,21 @@ static s32 igb_setup_fiber_serdes_link_82575(struct e1000_hw *hw) * mode that will be compatible with older link partners and switches. * However, both are supported by the hardware and some drivers/tools. */ - reg = rd32(E1000_PCS_LCTL); reg &= ~(E1000_PCS_LCTL_AN_ENABLE | E1000_PCS_LCTL_FLV_LINK_UP | E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); - if (hw->mac.autoneg) { + /* + * We force flow control to prevent the CTRL register values from being + * overwritten by the autonegotiated flow control values + */ + reg |= E1000_PCS_LCTL_FORCE_FCTRL; + + /* + * we always set sgmii to autoneg since it is the phy that will be + * forcing the link and the serdes is just a go-between + */ + if (hw->mac.autoneg || igb_sgmii_active_82575(hw)) { /* Set PCS register for autoneg */ reg |= E1000_PCS_LCTL_FSV_1000 | /* Force 1000 */ E1000_PCS_LCTL_FDV_FULL | /* SerDes Full duplex */ @@ -1053,75 +1101,12 @@ static s32 igb_setup_fiber_serdes_link_82575(struct e1000_hw *hw) hw_dbg("Configuring Forced Link; PCS_LCTL = 0x%08X\n", reg); } - if (hw->mac.type == e1000_82576) { - reg |= E1000_PCS_LCTL_FORCE_FCTRL; - igb_force_mac_fc(hw); - } - wr32(E1000_PCS_LCTL, reg); - return 0; -} - -/** - * igb_configure_pcs_link_82575 - Configure PCS link - * @hw: pointer to the HW structure - * - * Configure the physical coding sub-layer (PCS) link. The PCS link is - * only used on copper connections where the serialized gigabit media - * independent interface (sgmii) is being used. Configures the link - * for auto-negotiation or forces speed/duplex. - **/ -static void igb_configure_pcs_link_82575(struct e1000_hw *hw) -{ - struct e1000_mac_info *mac = &hw->mac; - u32 reg = 0; - - if (hw->phy.media_type != e1000_media_type_copper || - !(igb_sgmii_active_82575(hw))) - return; - - /* For SGMII, we need to issue a PCS autoneg restart */ - reg = rd32(E1000_PCS_LCTL); - - /* AN time out should be disabled for SGMII mode */ - reg &= ~(E1000_PCS_LCTL_AN_TIMEOUT); - - if (mac->autoneg) { - /* Make sure forced speed and force link are not set */ - reg &= ~(E1000_PCS_LCTL_FSD | E1000_PCS_LCTL_FORCE_LINK); - - /* - * The PHY should be setup prior to calling this function. - * All we need to do is restart autoneg and enable autoneg. - */ - reg |= E1000_PCS_LCTL_AN_RESTART | E1000_PCS_LCTL_AN_ENABLE; - } else { - /* Set PCS register for forced speed */ - - /* Turn off bits for full duplex, speed, and autoneg */ - reg &= ~(E1000_PCS_LCTL_FSV_1000 | - E1000_PCS_LCTL_FSV_100 | - E1000_PCS_LCTL_FDV_FULL | - E1000_PCS_LCTL_AN_ENABLE); - - /* Check for duplex first */ - if (mac->forced_speed_duplex & E1000_ALL_FULL_DUPLEX) - reg |= E1000_PCS_LCTL_FDV_FULL; - - /* Now set speed */ - if (mac->forced_speed_duplex & E1000_ALL_100_SPEED) - reg |= E1000_PCS_LCTL_FSV_100; - - /* Force speed and force link */ - reg |= E1000_PCS_LCTL_FSD | - E1000_PCS_LCTL_FORCE_LINK | - E1000_PCS_LCTL_FLV_LINK_UP; + if (!igb_sgmii_active_82575(hw)) + igb_force_mac_fc(hw); - hw_dbg("Wrote 0x%08X to PCS_LCTL to configure forced link\n", - reg); - } - wr32(E1000_PCS_LCTL, reg); + return 0; } /** @@ -1248,7 +1233,8 @@ static void igb_clear_hw_cntrs_82575(struct e1000_hw *hw) temp = rd32(E1000_LENERRS); /* This register should not be read in copper configurations */ - if (hw->phy.media_type == e1000_media_type_internal_serdes) + if (hw->phy.media_type == e1000_media_type_internal_serdes || + igb_sgmii_active_82575(hw)) temp = rd32(E1000_SCVPC); } diff --git a/drivers/net/igb/e1000_82575.h b/drivers/net/igb/e1000_82575.h index 8a1e6597061..ebd146fd4e1 100644 --- a/drivers/net/igb/e1000_82575.h +++ b/drivers/net/igb/e1000_82575.h @@ -28,7 +28,7 @@ #ifndef _E1000_82575_H_ #define _E1000_82575_H_ -extern void igb_shutdown_fiber_serdes_link_82575(struct e1000_hw *hw); +extern void igb_shutdown_serdes_link_82575(struct e1000_hw *hw); extern void igb_rx_fifo_flush_82575(struct e1000_hw *hw); #define ID_LED_DEFAULT_82575_SERDES ((ID_LED_DEF1_DEF2 << 12) | \ diff --git a/drivers/net/igb/e1000_defines.h b/drivers/net/igb/e1000_defines.h index c85829355d5..cb916833f30 100644 --- a/drivers/net/igb/e1000_defines.h +++ b/drivers/net/igb/e1000_defines.h @@ -44,7 +44,7 @@ #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */ /* Extended Device Control */ -#define E1000_CTRL_EXT_SDP7_DATA 0x00000080 /* Value of SW Defineable Pin 7 */ +#define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Defineable Pin 3 */ /* Physical Func Reset Done Indication */ #define E1000_CTRL_EXT_PFRSTD 0x00004000 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000 diff --git a/drivers/net/igb/e1000_mac.c b/drivers/net/igb/e1000_mac.c index a0231cd079f..7d76bb085e1 100644 --- a/drivers/net/igb/e1000_mac.c +++ b/drivers/net/igb/e1000_mac.c @@ -286,41 +286,6 @@ void igb_mta_set(struct e1000_hw *hw, u32 hash_value) } /** - * igb_update_mc_addr_list - Update Multicast addresses - * @hw: pointer to the HW structure - * @mc_addr_list: array of multicast addresses to program - * @mc_addr_count: number of multicast addresses to program - * - * Updates entire Multicast Table Array. - * The caller must have a packed mc_addr_list of multicast addresses. - **/ -void igb_update_mc_addr_list(struct e1000_hw *hw, - u8 *mc_addr_list, u32 mc_addr_count) -{ - u32 hash_value, hash_bit, hash_reg; - int i; - - /* clear mta_shadow */ - memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); - - /* update mta_shadow from mc_addr_list */ - for (i = 0; (u32) i < mc_addr_count; i++) { - hash_value = igb_hash_mc_addr(hw, mc_addr_list); - - hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); - hash_bit = hash_value & 0x1F; - - hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit); - mc_addr_list += (ETH_ALEN); - } - - /* replace the entire MTA table */ - for (i = hw->mac.mta_reg_count - 1; i >= 0; i--) - array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]); - wrfl(); -} - -/** * igb_hash_mc_addr - Generate a multicast hash value * @hw: pointer to the HW structure * @mc_addr: pointer to a multicast address @@ -329,7 +294,7 @@ void igb_update_mc_addr_list(struct e1000_hw *hw, * the multicast filter table array address and new table value. See * igb_mta_set() **/ -u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) +static u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) { u32 hash_value, hash_mask; u8 bit_shift = 0; @@ -392,6 +357,41 @@ u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr) } /** + * igb_update_mc_addr_list - Update Multicast addresses + * @hw: pointer to the HW structure + * @mc_addr_list: array of multicast addresses to program + * @mc_addr_count: number of multicast addresses to program + * + * Updates entire Multicast Table Array. + * The caller must have a packed mc_addr_list of multicast addresses. + **/ +void igb_update_mc_addr_list(struct e1000_hw *hw, + u8 *mc_addr_list, u32 mc_addr_count) +{ + u32 hash_value, hash_bit, hash_reg; + int i; + + /* clear mta_shadow */ + memset(&hw->mac.mta_shadow, 0, sizeof(hw->mac.mta_shadow)); + + /* update mta_shadow from mc_addr_list */ + for (i = 0; (u32) i < mc_addr_count; i++) { + hash_value = igb_hash_mc_addr(hw, mc_addr_list); + + hash_reg = (hash_value >> 5) & (hw->mac.mta_reg_count - 1); + hash_bit = hash_value & 0x1F; + + hw->mac.mta_shadow[hash_reg] |= (1 << hash_bit); + mc_addr_list += (ETH_ALEN); + } + + /* replace the entire MTA table */ + for (i = hw->mac.mta_reg_count - 1; i >= 0; i--) + array_wr32(E1000_MTA, i, hw->mac.mta_shadow[i]); + wrfl(); +} + +/** * igb_clear_hw_cntrs_base - Clear base hardware counters * @hw: pointer to the HW structure * diff --git a/drivers/net/igb/e1000_mac.h b/drivers/net/igb/e1000_mac.h index 7518af8cbbf..bca17d88241 100644 --- a/drivers/net/igb/e1000_mac.h +++ b/drivers/net/igb/e1000_mac.h @@ -88,6 +88,5 @@ enum e1000_mng_mode { #define E1000_MNG_DHCP_COOKIE_STATUS_VLAN 0x2 extern void e1000_init_function_pointers_82575(struct e1000_hw *hw); -extern u32 igb_hash_mc_addr(struct e1000_hw *hw, u8 *mc_addr); #endif diff --git a/drivers/net/igb/e1000_phy.c b/drivers/net/igb/e1000_phy.c index c1f4da63042..ee460600e74 100644 --- a/drivers/net/igb/e1000_phy.c +++ b/drivers/net/igb/e1000_phy.c @@ -1565,9 +1565,12 @@ out: **/ s32 igb_phy_sw_reset(struct e1000_hw *hw) { - s32 ret_val; + s32 ret_val = 0; u16 phy_ctrl; + if (!(hw->phy.ops.read_reg)) + goto out; + ret_val = hw->phy.ops.read_reg(hw, PHY_CONTROL, &phy_ctrl); if (ret_val) goto out; diff --git a/drivers/net/igb/igb_main.c b/drivers/net/igb/igb_main.c index 943186b7848..5d6c1530a8c 100644 --- a/drivers/net/igb/igb_main.c +++ b/drivers/net/igb/igb_main.c @@ -3966,7 +3966,7 @@ static int igb_set_vf_multicasts(struct igb_adapter *adapter, /* VFs are limited to using the MTA hash table for their multicast * addresses */ for (i = 0; i < n; i++) - vf_data->vf_mc_hashes[i] = hash_list[i];; + vf_data->vf_mc_hashes[i] = hash_list[i]; /* Flush and reset the mta with the new values */ igb_set_rx_mode(adapter->netdev); @@ -5320,7 +5320,7 @@ static int __igb_shutdown(struct pci_dev *pdev, bool *enable_wake) *enable_wake = wufc || adapter->en_mng_pt; if (!*enable_wake) - igb_shutdown_fiber_serdes_link_82575(hw); + igb_shutdown_serdes_link_82575(hw); /* Release control of h/w to f/w. If f/w is AMT enabled, this * would have already happened in close and is redundant. */ diff --git a/drivers/net/irda/kingsun-sir.c b/drivers/net/irda/kingsun-sir.c index 2fc30b449ee..cb90d640007 100644 --- a/drivers/net/irda/kingsun-sir.c +++ b/drivers/net/irda/kingsun-sir.c @@ -66,7 +66,6 @@ #include <linux/errno.h> #include <linux/init.h> #include <linux/slab.h> -#include <linux/kref.h> #include <linux/usb.h> #include <linux/device.h> #include <linux/crc32.h> diff --git a/drivers/net/irda/ks959-sir.c b/drivers/net/irda/ks959-sir.c index f4d13fc51cb..b54d3b48045 100644 --- a/drivers/net/irda/ks959-sir.c +++ b/drivers/net/irda/ks959-sir.c @@ -118,7 +118,6 @@ #include <linux/errno.h> #include <linux/init.h> #include <linux/slab.h> -#include <linux/kref.h> #include <linux/usb.h> #include <linux/device.h> #include <linux/crc32.h> diff --git a/drivers/net/irda/ksdazzle-sir.c b/drivers/net/irda/ksdazzle-sir.c index 5f9d7335397..8d713ebac15 100644 --- a/drivers/net/irda/ksdazzle-sir.c +++ b/drivers/net/irda/ksdazzle-sir.c @@ -82,7 +82,6 @@ #include <linux/errno.h> #include <linux/init.h> #include <linux/slab.h> -#include <linux/kref.h> #include <linux/usb.h> #include <linux/device.h> #include <linux/crc32.h> diff --git a/drivers/net/irda/mcs7780.c b/drivers/net/irda/mcs7780.c index b3d30bcb88e..c0e0bb9401d 100644 --- a/drivers/net/irda/mcs7780.c +++ b/drivers/net/irda/mcs7780.c @@ -50,7 +50,6 @@ #include <linux/errno.h> #include <linux/init.h> #include <linux/slab.h> -#include <linux/kref.h> #include <linux/usb.h> #include <linux/device.h> #include <linux/crc32.h> diff --git a/drivers/net/irda/pxaficp_ir.c b/drivers/net/irda/pxaficp_ir.c index 1445e586519..84db145d2b5 100644 --- a/drivers/net/irda/pxaficp_ir.c +++ b/drivers/net/irda/pxaficp_ir.c @@ -17,6 +17,7 @@ #include <linux/etherdevice.h> #include <linux/platform_device.h> #include <linux/clk.h> +#include <linux/gpio.h> #include <net/irda/irda.h> #include <net/irda/irmod.h> @@ -163,6 +164,22 @@ inline static void pxa_irda_fir_dma_tx_start(struct pxa_irda *si) } /* + * Set the IrDA communications mode. + */ +static void pxa_irda_set_mode(struct pxa_irda *si, int mode) +{ + if (si->pdata->transceiver_mode) + si->pdata->transceiver_mode(si->dev, mode); + else { + if (gpio_is_valid(si->pdata->gpio_pwdown)) + gpio_set_value(si->pdata->gpio_pwdown, + !(mode & IR_OFF) ^ + !si->pdata->gpio_pwdown_inverted); + pxa2xx_transceiver_mode(si->dev, mode); + } +} + +/* * Set the IrDA communications speed. */ static int pxa_irda_set_speed(struct pxa_irda *si, int speed) @@ -188,7 +205,7 @@ static int pxa_irda_set_speed(struct pxa_irda *si, int speed) pxa_irda_disable_clk(si); /* set board transceiver to SIR mode */ - si->pdata->transceiver_mode(si->dev, IR_SIRMODE); + pxa_irda_set_mode(si, IR_SIRMODE); /* enable the STUART clock */ pxa_irda_enable_sirclk(si); @@ -222,7 +239,7 @@ static int pxa_irda_set_speed(struct pxa_irda *si, int speed) ICCR0 = 0; /* set board transceiver to FIR mode */ - si->pdata->transceiver_mode(si->dev, IR_FIRMODE); + pxa_irda_set_mode(si, IR_FIRMODE); /* enable the FICP clock */ pxa_irda_enable_firclk(si); @@ -641,7 +658,7 @@ static void pxa_irda_shutdown(struct pxa_irda *si) local_irq_restore(flags); /* power off board transceiver */ - si->pdata->transceiver_mode(si->dev, IR_OFF); + pxa_irda_set_mode(si, IR_OFF); printk(KERN_DEBUG "pxa_ir: irda shutdown\n"); } @@ -849,10 +866,26 @@ static int pxa_irda_probe(struct platform_device *pdev) if (err) goto err_mem_5; - if (si->pdata->startup) + if (gpio_is_valid(si->pdata->gpio_pwdown)) { + err = gpio_request(si->pdata->gpio_pwdown, "IrDA switch"); + if (err) + goto err_startup; + err = gpio_direction_output(si->pdata->gpio_pwdown, + !si->pdata->gpio_pwdown_inverted); + if (err) { + gpio_free(si->pdata->gpio_pwdown); + goto err_startup; + } + } + + if (si->pdata->startup) { err = si->pdata->startup(si->dev); - if (err) - goto err_startup; + if (err) + goto err_startup; + } + + if (gpio_is_valid(si->pdata->gpio_pwdown) && si->pdata->startup) + dev_warn(si->dev, "gpio_pwdown and startup() both defined!\n"); dev->netdev_ops = &pxa_irda_netdev_ops; @@ -903,6 +936,8 @@ static int pxa_irda_remove(struct platform_device *_dev) if (dev) { struct pxa_irda *si = netdev_priv(dev); unregister_netdev(dev); + if (gpio_is_valid(si->pdata->gpio_pwdown)) + gpio_free(si->pdata->gpio_pwdown); if (si->pdata->shutdown) si->pdata->shutdown(si->dev); kfree(si->tx_buff.head); diff --git a/drivers/net/ixgbe/ixgbe.h b/drivers/net/ixgbe/ixgbe.h index dd688d45e9c..385be601666 100644 --- a/drivers/net/ixgbe/ixgbe.h +++ b/drivers/net/ixgbe/ixgbe.h @@ -267,7 +267,8 @@ struct ixgbe_adapter { enum ixgbe_fc_mode last_lfc_mode; /* Interrupt Throttle Rate */ - u32 itr_setting; + u32 rx_itr_setting; + u32 tx_itr_setting; u16 eitr_low; u16 eitr_high; @@ -351,7 +352,8 @@ struct ixgbe_adapter { struct ixgbe_hw_stats stats; /* Interrupt Throttle Rate */ - u32 eitr_param; + u32 rx_eitr_param; + u32 tx_eitr_param; unsigned long state; u64 tx_busy; diff --git a/drivers/net/ixgbe/ixgbe_82598.c b/drivers/net/ixgbe/ixgbe_82598.c index cb7f0c3c6e1..56b12f3192f 100644 --- a/drivers/net/ixgbe/ixgbe_82598.c +++ b/drivers/net/ixgbe/ixgbe_82598.c @@ -322,14 +322,16 @@ static enum ixgbe_media_type ixgbe_get_media_type_82598(struct ixgbe_hw *hw) break; case IXGBE_DEV_ID_82598AF_DUAL_PORT: case IXGBE_DEV_ID_82598AF_SINGLE_PORT: - case IXGBE_DEV_ID_82598EB_CX4: - case IXGBE_DEV_ID_82598_CX4_DUAL_PORT: case IXGBE_DEV_ID_82598_DA_DUAL_PORT: case IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM: case IXGBE_DEV_ID_82598EB_XF_LR: case IXGBE_DEV_ID_82598EB_SFP_LOM: media_type = ixgbe_media_type_fiber; break; + case IXGBE_DEV_ID_82598EB_CX4: + case IXGBE_DEV_ID_82598_CX4_DUAL_PORT: + media_type = ixgbe_media_type_cx4; + break; case IXGBE_DEV_ID_82598AT: case IXGBE_DEV_ID_82598AT2: media_type = ixgbe_media_type_copper; diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c index 61af47e75aa..2ec58dcdb82 100644 --- a/drivers/net/ixgbe/ixgbe_82599.c +++ b/drivers/net/ixgbe/ixgbe_82599.c @@ -337,6 +337,9 @@ static enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw) case IXGBE_DEV_ID_82599_SFP: media_type = ixgbe_media_type_fiber; break; + case IXGBE_DEV_ID_82599_CX4: + media_type = ixgbe_media_type_cx4; + break; default: media_type = ixgbe_media_type_unknown; break; diff --git a/drivers/net/ixgbe/ixgbe_ethtool.c b/drivers/net/ixgbe/ixgbe_ethtool.c index 026e94a9984..53b0a668025 100644 --- a/drivers/net/ixgbe/ixgbe_ethtool.c +++ b/drivers/net/ixgbe/ixgbe_ethtool.c @@ -1929,7 +1929,7 @@ static int ixgbe_get_coalesce(struct net_device *netdev, ec->tx_max_coalesced_frames_irq = adapter->tx_ring[0].work_limit; /* only valid if in constant ITR mode */ - switch (adapter->itr_setting) { + switch (adapter->rx_itr_setting) { case 0: /* throttling disabled */ ec->rx_coalesce_usecs = 0; @@ -1940,9 +1940,25 @@ static int ixgbe_get_coalesce(struct net_device *netdev, break; default: /* fixed interrupt rate mode */ - ec->rx_coalesce_usecs = 1000000/adapter->eitr_param; + ec->rx_coalesce_usecs = 1000000/adapter->rx_eitr_param; break; } + + /* only valid if in constant ITR mode */ + switch (adapter->tx_itr_setting) { + case 0: + /* throttling disabled */ + ec->tx_coalesce_usecs = 0; + break; + case 1: + /* dynamic ITR mode */ + ec->tx_coalesce_usecs = 1; + break; + default: + ec->tx_coalesce_usecs = 1000000/adapter->tx_eitr_param; + break; + } + return 0; } @@ -1953,6 +1969,14 @@ static int ixgbe_set_coalesce(struct net_device *netdev, struct ixgbe_q_vector *q_vector; int i; + /* + * don't accept tx specific changes if we've got mixed RxTx vectors + * test and jump out here if needed before changing the rx numbers + */ + if ((1000000/ec->tx_coalesce_usecs) != adapter->tx_eitr_param && + adapter->q_vector[0]->txr_count && adapter->q_vector[0]->rxr_count) + return -EINVAL; + if (ec->tx_max_coalesced_frames_irq) adapter->tx_ring[0].work_limit = ec->tx_max_coalesced_frames_irq; @@ -1963,26 +1987,49 @@ static int ixgbe_set_coalesce(struct net_device *netdev, return -EINVAL; /* store the value in ints/second */ - adapter->eitr_param = 1000000/ec->rx_coalesce_usecs; + adapter->rx_eitr_param = 1000000/ec->rx_coalesce_usecs; /* static value of interrupt rate */ - adapter->itr_setting = adapter->eitr_param; + adapter->rx_itr_setting = adapter->rx_eitr_param; /* clear the lower bit as its used for dynamic state */ - adapter->itr_setting &= ~1; + adapter->rx_itr_setting &= ~1; } else if (ec->rx_coalesce_usecs == 1) { /* 1 means dynamic mode */ - adapter->eitr_param = 20000; - adapter->itr_setting = 1; + adapter->rx_eitr_param = 20000; + adapter->rx_itr_setting = 1; } else { /* * any other value means disable eitr, which is best * served by setting the interrupt rate very high */ if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) - adapter->eitr_param = IXGBE_MAX_RSC_INT_RATE; + adapter->rx_eitr_param = IXGBE_MAX_RSC_INT_RATE; else - adapter->eitr_param = IXGBE_MAX_INT_RATE; - adapter->itr_setting = 0; + adapter->rx_eitr_param = IXGBE_MAX_INT_RATE; + adapter->rx_itr_setting = 0; + } + + if (ec->tx_coalesce_usecs > 1) { + /* check the limits */ + if ((1000000/ec->tx_coalesce_usecs > IXGBE_MAX_INT_RATE) || + (1000000/ec->tx_coalesce_usecs < IXGBE_MIN_INT_RATE)) + return -EINVAL; + + /* store the value in ints/second */ + adapter->tx_eitr_param = 1000000/ec->tx_coalesce_usecs; + + /* static value of interrupt rate */ + adapter->tx_itr_setting = adapter->tx_eitr_param; + + /* clear the lower bit as its used for dynamic state */ + adapter->tx_itr_setting &= ~1; + } else if (ec->tx_coalesce_usecs == 1) { + /* 1 means dynamic mode */ + adapter->tx_eitr_param = 10000; + adapter->tx_itr_setting = 1; + } else { + adapter->tx_eitr_param = IXGBE_MAX_INT_RATE; + adapter->tx_itr_setting = 0; } /* MSI/MSIx Interrupt Mode */ @@ -1992,17 +2039,17 @@ static int ixgbe_set_coalesce(struct net_device *netdev, for (i = 0; i < num_vectors; i++) { q_vector = adapter->q_vector[i]; if (q_vector->txr_count && !q_vector->rxr_count) - /* tx vector gets half the rate */ - q_vector->eitr = (adapter->eitr_param >> 1); + /* tx only */ + q_vector->eitr = adapter->tx_eitr_param; else /* rx only or mixed */ - q_vector->eitr = adapter->eitr_param; + q_vector->eitr = adapter->rx_eitr_param; ixgbe_write_eitr(q_vector); } /* Legacy Interrupt Mode */ } else { q_vector = adapter->q_vector[0]; - q_vector->eitr = adapter->eitr_param; + q_vector->eitr = adapter->rx_eitr_param; ixgbe_write_eitr(q_vector); } diff --git a/drivers/net/ixgbe/ixgbe_main.c b/drivers/net/ixgbe/ixgbe_main.c index 45bf8b9716e..c407bd9de0d 100644 --- a/drivers/net/ixgbe/ixgbe_main.c +++ b/drivers/net/ixgbe/ixgbe_main.c @@ -97,6 +97,8 @@ static struct pci_device_id ixgbe_pci_tbl[] = { board_82599 }, {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_SFP), board_82599 }, + {PCI_VDEVICE(INTEL, IXGBE_DEV_ID_82599_CX4), + board_82599 }, /* required last entry */ {0, } @@ -924,12 +926,12 @@ static void ixgbe_configure_msix(struct ixgbe_adapter *adapter) r_idx + 1); } - /* if this is a tx only vector halve the interrupt rate */ if (q_vector->txr_count && !q_vector->rxr_count) - q_vector->eitr = (adapter->eitr_param >> 1); + /* tx only */ + q_vector->eitr = adapter->tx_eitr_param; else if (q_vector->rxr_count) - /* rx only */ - q_vector->eitr = adapter->eitr_param; + /* rx or mixed */ + q_vector->eitr = adapter->rx_eitr_param; ixgbe_write_eitr(q_vector); } @@ -1357,7 +1359,7 @@ static int ixgbe_clean_rxonly(struct napi_struct *napi, int budget) /* If all Rx work done, exit the polling mode */ if (work_done < budget) { napi_complete(napi); - if (adapter->itr_setting & 1) + if (adapter->rx_itr_setting & 1) ixgbe_set_itr_msix(q_vector); if (!test_bit(__IXGBE_DOWN, &adapter->state)) ixgbe_irq_enable_queues(adapter, @@ -1418,7 +1420,7 @@ static int ixgbe_clean_rxtx_many(struct napi_struct *napi, int budget) /* If all Rx work done, exit the polling mode */ if (work_done < budget) { napi_complete(napi); - if (adapter->itr_setting & 1) + if (adapter->rx_itr_setting & 1) ixgbe_set_itr_msix(q_vector); if (!test_bit(__IXGBE_DOWN, &adapter->state)) ixgbe_irq_enable_queues(adapter, @@ -1456,10 +1458,10 @@ static int ixgbe_clean_txonly(struct napi_struct *napi, int budget) if (!ixgbe_clean_tx_irq(q_vector, tx_ring)) work_done = budget; - /* If all Rx work done, exit the polling mode */ + /* If all Tx work done, exit the polling mode */ if (work_done < budget) { napi_complete(napi); - if (adapter->itr_setting & 1) + if (adapter->tx_itr_setting & 1) ixgbe_set_itr_msix(q_vector); if (!test_bit(__IXGBE_DOWN, &adapter->state)) ixgbe_irq_enable_queues(adapter, ((u64)1 << q_vector->v_idx)); @@ -1846,7 +1848,7 @@ static void ixgbe_configure_msi_and_legacy(struct ixgbe_adapter *adapter) struct ixgbe_hw *hw = &adapter->hw; IXGBE_WRITE_REG(hw, IXGBE_EITR(0), - EITR_INTS_PER_SEC_TO_REG(adapter->eitr_param)); + EITR_INTS_PER_SEC_TO_REG(adapter->rx_eitr_param)); ixgbe_set_ivar(adapter, 0, 0, 0); ixgbe_set_ivar(adapter, 1, 0, 0); @@ -1968,6 +1970,50 @@ static u32 ixgbe_setup_mrqc(struct ixgbe_adapter *adapter) } /** + * ixgbe_configure_rscctl - enable RSC for the indicated ring + * @adapter: address of board private structure + * @index: index of ring to set + * @rx_buf_len: rx buffer length + **/ +static void ixgbe_configure_rscctl(struct ixgbe_adapter *adapter, int index, + int rx_buf_len) +{ + struct ixgbe_ring *rx_ring; + struct ixgbe_hw *hw = &adapter->hw; + int j; + u32 rscctrl; + + rx_ring = &adapter->rx_ring[index]; + j = rx_ring->reg_idx; + rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j)); + rscctrl |= IXGBE_RSCCTL_RSCEN; + /* + * we must limit the number of descriptors so that the + * total size of max desc * buf_len is not greater + * than 65535 + */ + if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { +#if (MAX_SKB_FRAGS > 16) + rscctrl |= IXGBE_RSCCTL_MAXDESC_16; +#elif (MAX_SKB_FRAGS > 8) + rscctrl |= IXGBE_RSCCTL_MAXDESC_8; +#elif (MAX_SKB_FRAGS > 4) + rscctrl |= IXGBE_RSCCTL_MAXDESC_4; +#else + rscctrl |= IXGBE_RSCCTL_MAXDESC_1; +#endif + } else { + if (rx_buf_len < IXGBE_RXBUFFER_4096) + rscctrl |= IXGBE_RSCCTL_MAXDESC_16; + else if (rx_buf_len < IXGBE_RXBUFFER_8192) + rscctrl |= IXGBE_RSCCTL_MAXDESC_8; + else + rscctrl |= IXGBE_RSCCTL_MAXDESC_4; + } + IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(j), rscctrl); +} + +/** * ixgbe_configure_rx - Configure 8259x Receive Unit after Reset * @adapter: board private structure * @@ -1988,7 +2034,6 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) u32 fctrl, hlreg0; u32 reta = 0, mrqc = 0; u32 rdrxctl; - u32 rscctrl; int rx_buf_len; /* Decide whether to use packet split mode or not */ @@ -2055,6 +2100,8 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) if (adapter->flags & IXGBE_FLAG_RX_PS_ENABLED) rx_ring->flags |= IXGBE_RING_RX_PS_ENABLED; + else + rx_ring->flags &= ~IXGBE_RING_RX_PS_ENABLED; #ifdef IXGBE_FCOE if (netdev->features & NETIF_F_FCOE_MTU) { @@ -2144,36 +2191,9 @@ static void ixgbe_configure_rx(struct ixgbe_adapter *adapter) if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) { /* Enable 82599 HW-RSC */ - for (i = 0; i < adapter->num_rx_queues; i++) { - rx_ring = &adapter->rx_ring[i]; - j = rx_ring->reg_idx; - rscctrl = IXGBE_READ_REG(hw, IXGBE_RSCCTL(j)); - rscctrl |= IXGBE_RSCCTL_RSCEN; - /* - * we must limit the number of descriptors so that the - * total size of max desc * buf_len is not greater - * than 65535 - */ - if (rx_ring->flags & IXGBE_RING_RX_PS_ENABLED) { -#if (MAX_SKB_FRAGS > 16) - rscctrl |= IXGBE_RSCCTL_MAXDESC_16; -#elif (MAX_SKB_FRAGS > 8) - rscctrl |= IXGBE_RSCCTL_MAXDESC_8; -#elif (MAX_SKB_FRAGS > 4) - rscctrl |= IXGBE_RSCCTL_MAXDESC_4; -#else - rscctrl |= IXGBE_RSCCTL_MAXDESC_1; -#endif - } else { - if (rx_buf_len < IXGBE_RXBUFFER_4096) - rscctrl |= IXGBE_RSCCTL_MAXDESC_16; - else if (rx_buf_len < IXGBE_RXBUFFER_8192) - rscctrl |= IXGBE_RSCCTL_MAXDESC_8; - else - rscctrl |= IXGBE_RSCCTL_MAXDESC_4; - } - IXGBE_WRITE_REG(hw, IXGBE_RSCCTL(j), rscctrl); - } + for (i = 0; i < adapter->num_rx_queues; i++) + ixgbe_configure_rscctl(adapter, i, rx_buf_len); + /* Disable RSC for ACK packets */ IXGBE_WRITE_REG(hw, IXGBE_RSCDBU, (IXGBE_RSCDBU_RSCACKDIS | IXGBE_READ_REG(hw, IXGBE_RSCDBU))); @@ -2922,6 +2942,8 @@ void ixgbe_down(struct ixgbe_adapter *adapter) ixgbe_napi_disable_all(adapter); + clear_bit(__IXGBE_SFP_MODULE_NOT_FOUND, &adapter->state); + del_timer_sync(&adapter->sfp_timer); del_timer_sync(&adapter->watchdog_timer); cancel_work_sync(&adapter->watchdog_task); @@ -2985,7 +3007,7 @@ static int ixgbe_poll(struct napi_struct *napi, int budget) /* If budget not fully consumed, exit the polling mode */ if (work_done < budget) { napi_complete(napi); - if (adapter->itr_setting & 1) + if (adapter->rx_itr_setting & 1) ixgbe_set_itr(adapter); if (!test_bit(__IXGBE_DOWN, &adapter->state)) ixgbe_irq_enable_queues(adapter, IXGBE_EIMS_RTX_QUEUE); @@ -3595,7 +3617,10 @@ static int ixgbe_alloc_q_vectors(struct ixgbe_adapter *adapter) if (!q_vector) goto err_out; q_vector->adapter = adapter; - q_vector->eitr = adapter->eitr_param; + if (q_vector->txr_count && !q_vector->rxr_count) + q_vector->eitr = adapter->tx_eitr_param; + else + q_vector->eitr = adapter->rx_eitr_param; q_vector->v_idx = q_idx; netif_napi_add(adapter->netdev, &q_vector->napi, (*poll), 64); adapter->q_vector[q_idx] = q_vector; @@ -3864,8 +3889,10 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter) hw->fc.disable_fc_autoneg = false; /* enable itr by default in dynamic mode */ - adapter->itr_setting = 1; - adapter->eitr_param = 20000; + adapter->rx_itr_setting = 1; + adapter->rx_eitr_param = 20000; + adapter->tx_itr_setting = 1; + adapter->tx_eitr_param = 10000; /* set defaults for eitr in MegaBytes */ adapter->eitr_low = 10; diff --git a/drivers/net/ixgbe/ixgbe_type.h b/drivers/net/ixgbe/ixgbe_type.h index 8ba90eec1dc..8761d7899f7 100644 --- a/drivers/net/ixgbe/ixgbe_type.h +++ b/drivers/net/ixgbe/ixgbe_type.h @@ -49,6 +49,7 @@ #define IXGBE_DEV_ID_82598_SR_DUAL_PORT_EM 0x10E1 #define IXGBE_DEV_ID_82598EB_XF_LR 0x10F4 #define IXGBE_DEV_ID_82599_KX4 0x10F7 +#define IXGBE_DEV_ID_82599_CX4 0x10F9 #define IXGBE_DEV_ID_82599_SFP 0x10FB #define IXGBE_DEV_ID_82599_XAUI_LOM 0x10FC @@ -2143,6 +2144,7 @@ enum ixgbe_media_type { ixgbe_media_type_fiber, ixgbe_media_type_copper, ixgbe_media_type_backplane, + ixgbe_media_type_cx4, ixgbe_media_type_virtual }; diff --git a/drivers/net/ks8851.c b/drivers/net/ks8851.c index 547ac7c7479..23783586435 100644 --- a/drivers/net/ks8851.c +++ b/drivers/net/ks8851.c @@ -1321,3 +1321,4 @@ MODULE_LICENSE("GPL"); module_param_named(message, msg_enable, int, 0); MODULE_PARM_DESC(message, "Message verbosity level (0=none, 31=all)"); +MODULE_ALIAS("spi:ks8851"); diff --git a/drivers/net/ll_temac_main.c b/drivers/net/ll_temac_main.c index da8d0a0ca94..f2a197fd47a 100644 --- a/drivers/net/ll_temac_main.c +++ b/drivers/net/ll_temac_main.c @@ -865,7 +865,7 @@ temac_of_probe(struct of_device *op, const struct of_device_id *match) dcrs = dcr_resource_start(np, 0); if (dcrs == 0) { dev_err(&op->dev, "could not get DMA register address\n"); - goto nodev;; + goto nodev; } lp->sdma_dcrs = dcr_map(np, dcrs, dcr_resource_len(np, 0)); dev_dbg(&op->dev, "DCR base: %x\n", dcrs); diff --git a/drivers/net/macb.c b/drivers/net/macb.c index fb65b427c69..1d0d4d9ab62 100644 --- a/drivers/net/macb.c +++ b/drivers/net/macb.c @@ -241,7 +241,7 @@ static int macb_mii_init(struct macb *bp) struct eth_platform_data *pdata; int err = -ENXIO, i; - /* Enable managment port */ + /* Enable management port */ macb_writel(bp, NCR, MACB_BIT(MPE)); bp->mii_bus = mdiobus_alloc(); diff --git a/drivers/net/mlx4/catas.c b/drivers/net/mlx4/catas.c index aa9674b7f19..f599294fa8a 100644 --- a/drivers/net/mlx4/catas.c +++ b/drivers/net/mlx4/catas.c @@ -96,12 +96,17 @@ static void catas_reset(struct work_struct *work) spin_unlock_irq(&catas_lock); list_for_each_entry_safe(priv, tmppriv, &tlist, catas_err.list) { + struct pci_dev *pdev = priv->dev.pdev; + ret = mlx4_restart_one(priv->dev.pdev); - dev = &priv->dev; + /* 'priv' now is not valid */ if (ret) - mlx4_err(dev, "Reset failed (%d)\n", ret); - else + printk(KERN_ERR "mlx4 %s: Reset failed (%d)\n", + pci_name(pdev), ret); + else { + dev = pci_get_drvdata(pdev); mlx4_dbg(dev, "Reset succeeded\n"); + } } } diff --git a/drivers/net/mlx4/fw.c b/drivers/net/mlx4/fw.c index cee199ceba2..3c16602172f 100644 --- a/drivers/net/mlx4/fw.c +++ b/drivers/net/mlx4/fw.c @@ -33,6 +33,7 @@ */ #include <linux/mlx4/cmd.h> +#include <linux/cache.h> #include "fw.h" #include "icm.h" @@ -698,6 +699,7 @@ int mlx4_INIT_HCA(struct mlx4_dev *dev, struct mlx4_init_hca_param *param) #define INIT_HCA_IN_SIZE 0x200 #define INIT_HCA_VERSION_OFFSET 0x000 #define INIT_HCA_VERSION 2 +#define INIT_HCA_CACHELINE_SZ_OFFSET 0x0e #define INIT_HCA_FLAGS_OFFSET 0x014 #define INIT_HCA_QPC_OFFSET 0x020 #define INIT_HCA_QPC_BASE_OFFSET (INIT_HCA_QPC_OFFSET + 0x10) @@ -735,6 +737,9 @@ int mlx4_INIT_HCA(struct mlx4_dev *dev, struct mlx4_init_hca_param *param) *((u8 *) mailbox->buf + INIT_HCA_VERSION_OFFSET) = INIT_HCA_VERSION; + *((u8 *) mailbox->buf + INIT_HCA_CACHELINE_SZ_OFFSET) = + (ilog2(cache_line_size()) - 4) << 5; + #if defined(__LITTLE_ENDIAN) *(inbox + INIT_HCA_FLAGS_OFFSET / 4) &= ~cpu_to_be32(1 << 1); #elif defined(__BIG_ENDIAN) diff --git a/drivers/net/netxen/netxen_nic_main.c b/drivers/net/netxen/netxen_nic_main.c index f7bdde111df..b5aa974827e 100644 --- a/drivers/net/netxen/netxen_nic_main.c +++ b/drivers/net/netxen/netxen_nic_main.c @@ -1469,6 +1469,7 @@ netxen_nic_resume(struct pci_dev *pdev) } netxen_schedule_work(adapter, netxen_fw_poll_work, FW_POLL_DELAY); + return 0; err_out_detach: netxen_nic_detach(adapter); @@ -1903,12 +1904,13 @@ static void netxen_tx_timeout_task(struct work_struct *work) netif_wake_queue(adapter->netdev); - goto done; + clear_bit(__NX_RESETTING, &adapter->state); } else { + clear_bit(__NX_RESETTING, &adapter->state); if (!netxen_nic_reset_context(adapter)) { adapter->netdev->trans_start = jiffies; - goto done; + return; } /* context reset failed, fall through for fw reset */ @@ -1916,8 +1918,6 @@ static void netxen_tx_timeout_task(struct work_struct *work) request_reset: adapter->need_fw_reset = 1; -done: - clear_bit(__NX_RESETTING, &adapter->state); } struct net_device_stats *netxen_nic_get_stats(struct net_device *netdev) diff --git a/drivers/net/ni52.c b/drivers/net/ni52.c index bd0ac690d12..aad3b370c56 100644 --- a/drivers/net/ni52.c +++ b/drivers/net/ni52.c @@ -615,10 +615,10 @@ static int init586(struct net_device *dev) /* addr_len |!src_insert |pre-len |loopback */ writeb(0x2e, &cfg_cmd->adr_len); writeb(0x00, &cfg_cmd->priority); - writeb(0x60, &cfg_cmd->ifs);; + writeb(0x60, &cfg_cmd->ifs); writeb(0x00, &cfg_cmd->time_low); writeb(0xf2, &cfg_cmd->time_high); - writeb(0x00, &cfg_cmd->promisc);; + writeb(0x00, &cfg_cmd->promisc); if (dev->flags & IFF_ALLMULTI) { int len = ((char __iomem *)p->iscp - (char __iomem *)ptr - 8) / 6; if (num_addrs > len) { diff --git a/drivers/net/niu.c b/drivers/net/niu.c index 76cc2614f48..f9364d0678f 100644 --- a/drivers/net/niu.c +++ b/drivers/net/niu.c @@ -5615,7 +5615,7 @@ static void niu_init_tx_mac(struct niu *np) /* The XMAC_MIN register only accepts values for TX min which * have the low 3 bits cleared. */ - BUILD_BUG_ON(min & 0x7); + BUG_ON(min & 0x7); if (np->flags & NIU_FLAGS_XMAC) niu_init_tx_xmac(np, min, max); diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c index 90a94d21583..474876c879c 100644 --- a/drivers/net/pcmcia/pcnet_cs.c +++ b/drivers/net/pcmcia/pcnet_cs.c @@ -340,12 +340,11 @@ static hw_info_t *get_hwinfo(struct pcmcia_device *link) base = &virt[hw_info[i].offset & (req.Size-1)]; if ((readb(base+0) == hw_info[i].a0) && (readb(base+2) == hw_info[i].a1) && - (readb(base+4) == hw_info[i].a2)) - break; - } - if (i < NR_INFO) { - for (j = 0; j < 6; j++) - dev->dev_addr[j] = readb(base + (j<<1)); + (readb(base+4) == hw_info[i].a2)) { + for (j = 0; j < 6; j++) + dev->dev_addr[j] = readb(base + (j<<1)); + break; + } } iounmap(virt); @@ -1750,11 +1749,11 @@ static struct pcmcia_device_id pcnet_ids[] = { PCMCIA_DEVICE_PROD_ID2("EN-6200P2", 0xa996d078), /* too generic! */ /* PCMCIA_DEVICE_PROD_ID12("PCMCIA", "10/100 Ethernet Card", 0x281f1c5d, 0x11b0ffc0), */ - PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "PCMCIA", "EN2218-LAN/MODEM", 0x281f1c5d, 0x570f348e, "PCMLM28.cis"), - PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "PCMCIA", "UE2218-LAN/MODEM", 0x281f1c5d, 0x6fdcacee, "PCMLM28.cis"), - PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "Psion Dacom", "Gold Card V34 Ethernet", 0xf5f025c2, 0x338e8155, "PCMLM28.cis"), - PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "Psion Dacom", "Gold Card V34 Ethernet GSM", 0xf5f025c2, 0x4ae85d35, "PCMLM28.cis"), - PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "LINKSYS", "PCMLM28", 0xf7cb0b07, 0x66881874, "PCMLM28.cis"), + PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "PCMCIA", "EN2218-LAN/MODEM", 0x281f1c5d, 0x570f348e, "cis/PCMLM28.cis"), + PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "PCMCIA", "UE2218-LAN/MODEM", 0x281f1c5d, 0x6fdcacee, "cis/PCMLM28.cis"), + PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "Psion Dacom", "Gold Card V34 Ethernet", 0xf5f025c2, 0x338e8155, "cis/PCMLM28.cis"), + PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "Psion Dacom", "Gold Card V34 Ethernet GSM", 0xf5f025c2, 0x4ae85d35, "cis/PCMLM28.cis"), + PCMCIA_PFC_DEVICE_CIS_PROD_ID12(0, "LINKSYS", "PCMLM28", 0xf7cb0b07, 0x66881874, "cis/PCMLM28.cis"), PCMCIA_MFC_DEVICE_CIS_PROD_ID12(0, "DAYNA COMMUNICATIONS", "LAN AND MODEM MULTIFUNCTION", 0x8fdf8f89, 0xdd5ed9e8, "DP83903.cis"), PCMCIA_MFC_DEVICE_CIS_PROD_ID4(0, "NSC MF LAN/Modem", 0x58fc6056, "DP83903.cis"), PCMCIA_MFC_DEVICE_CIS_MANF_CARD(0, 0x0175, 0x0000, "DP83903.cis"), diff --git a/drivers/net/pppol2tp.c b/drivers/net/pppol2tp.c index e0f9219a0ae..cc394d07375 100644 --- a/drivers/net/pppol2tp.c +++ b/drivers/net/pppol2tp.c @@ -229,7 +229,7 @@ static void pppol2tp_tunnel_free(struct pppol2tp_tunnel *tunnel); static atomic_t pppol2tp_tunnel_count; static atomic_t pppol2tp_session_count; static struct ppp_channel_ops pppol2tp_chan_ops = { pppol2tp_xmit , NULL }; -static struct proto_ops pppol2tp_ops; +static const struct proto_ops pppol2tp_ops; /* per-net private data for this module */ static int pppol2tp_net_id; @@ -2574,7 +2574,7 @@ static const struct file_operations pppol2tp_proc_fops = { * Init and cleanup *****************************************************************************/ -static struct proto_ops pppol2tp_ops = { +static const struct proto_ops pppol2tp_ops = { .family = AF_PPPOX, .owner = THIS_MODULE, .release = pppol2tp_release, diff --git a/drivers/net/qlge/qlge_main.c b/drivers/net/qlge/qlge_main.c index 22052925782..7783c5db81d 100644 --- a/drivers/net/qlge/qlge_main.c +++ b/drivers/net/qlge/qlge_main.c @@ -2630,7 +2630,7 @@ static int ql_start_rx_ring(struct ql_adapter *qdev, struct rx_ring *rx_ring) FLAGS_LI; /* Load irq delay values */ if (rx_ring->lbq_len) { cqicb->flags |= FLAGS_LL; /* Load lbq values */ - tmp = (u64)rx_ring->lbq_base_dma;; + tmp = (u64)rx_ring->lbq_base_dma; base_indirect_ptr = (__le64 *) rx_ring->lbq_base_indirect; page_entries = 0; do { @@ -2654,7 +2654,7 @@ static int ql_start_rx_ring(struct ql_adapter *qdev, struct rx_ring *rx_ring) } if (rx_ring->sbq_len) { cqicb->flags |= FLAGS_LS; /* Load sbq values */ - tmp = (u64)rx_ring->sbq_base_dma;; + tmp = (u64)rx_ring->sbq_base_dma; base_indirect_ptr = (__le64 *) rx_ring->sbq_base_indirect; page_entries = 0; do { diff --git a/drivers/net/rionet.c b/drivers/net/rionet.c index bc98e7f69ee..ede937ee50c 100644 --- a/drivers/net/rionet.c +++ b/drivers/net/rionet.c @@ -72,7 +72,7 @@ static int rionet_check = 0; static int rionet_capable = 1; /* - * This is a fast lookup table for for translating TX + * This is a fast lookup table for translating TX * Ethernet packets into a destination RIO device. It * could be made into a hash table to save memory depending * on system trade-offs. diff --git a/drivers/net/sfc/efx.c b/drivers/net/sfc/efx.c index 07a7e4b8f8f..cc4b2f99989 100644 --- a/drivers/net/sfc/efx.c +++ b/drivers/net/sfc/efx.c @@ -884,13 +884,12 @@ static int efx_wanted_rx_queues(void) int count; int cpu; - if (unlikely(!alloc_cpumask_var(&core_mask, GFP_KERNEL))) { + if (unlikely(!zalloc_cpumask_var(&core_mask, GFP_KERNEL))) { printk(KERN_WARNING "sfc: RSS disabled due to allocation failure\n"); return 1; } - cpumask_clear(core_mask); count = 0; for_each_online_cpu(cpu) { if (!cpumask_test_cpu(cpu, core_mask)) { diff --git a/drivers/net/skfp/pcmplc.c b/drivers/net/skfp/pcmplc.c index f1df2ec8ad4..e6b33ee05ed 100644 --- a/drivers/net/skfp/pcmplc.c +++ b/drivers/net/skfp/pcmplc.c @@ -960,7 +960,7 @@ static void pcm_fsm(struct s_smc *smc, struct s_phy *phy, int cmd) /*PC88b*/ if (!phy->cf_join) { phy->cf_join = TRUE ; - queue_event(smc,EVENT_CFM,CF_JOIN+np) ; ; + queue_event(smc,EVENT_CFM,CF_JOIN+np) ; } if (cmd == PC_JOIN) GO_STATE(PC8_ACTIVE) ; diff --git a/drivers/net/skfp/pmf.c b/drivers/net/skfp/pmf.c index 79e665e0853..a320fdb3727 100644 --- a/drivers/net/skfp/pmf.c +++ b/drivers/net/skfp/pmf.c @@ -807,9 +807,9 @@ void smt_add_para(struct s_smc *smc, struct s_pcon *pcon, u_short para, mib_p->fddiPORTLerFlag ; sp->p4050_pad = 0 ; sp->p4050_cutoff = - mib_p->fddiPORTLer_Cutoff ; ; + mib_p->fddiPORTLer_Cutoff ; sp->p4050_alarm = - mib_p->fddiPORTLer_Alarm ; ; + mib_p->fddiPORTLer_Alarm ; sp->p4050_estimate = mib_p->fddiPORTLer_Estimate ; sp->p4050_reject_ct = @@ -829,7 +829,7 @@ void smt_add_para(struct s_smc *smc, struct s_pcon *pcon, u_short para, sp->p4051_porttype = mib_p->fddiPORTMy_Type ; sp->p4051_connectstate = - mib_p->fddiPORTConnectState ; ; + mib_p->fddiPORTConnectState ; sp->p4051_pc_neighbor = mib_p->fddiPORTNeighborType ; sp->p4051_pc_withhold = @@ -853,7 +853,7 @@ void smt_add_para(struct s_smc *smc, struct s_pcon *pcon, u_short para, struct smt_p_4053 *sp ; sp = (struct smt_p_4053 *) to ; sp->p4053_multiple = - mib_p->fddiPORTMultiple_P ; ; + mib_p->fddiPORTMultiple_P ; sp->p4053_availablepaths = mib_p->fddiPORTAvailablePaths ; sp->p4053_currentpath = diff --git a/drivers/net/skge.c b/drivers/net/skge.c index 62e852e21ab..55bad408196 100644 --- a/drivers/net/skge.c +++ b/drivers/net/skge.c @@ -215,7 +215,7 @@ static void skge_wol_init(struct skge_port *skge) if (skge->wol & WAKE_MAGIC) ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT; else - ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT;; + ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT; ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT; skge_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl); diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index 00bc65a0aac..ef1165718dd 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -65,8 +65,8 @@ #define RX_DEF_PENDING RX_MAX_PENDING /* This is the worst case number of transmit list elements for a single skb: - VLAN + TSO + CKSUM + Data + skb_frags * DMA */ -#define MAX_SKB_TX_LE (4 + (sizeof(dma_addr_t)/sizeof(u32))*MAX_SKB_FRAGS) + VLAN:GSO + CKSUM + Data + skb_frags * DMA */ +#define MAX_SKB_TX_LE (2 + (sizeof(dma_addr_t)/sizeof(u32))*(MAX_SKB_FRAGS+1)) #define TX_MIN_PENDING (MAX_SKB_TX_LE+1) #define TX_MAX_PENDING 4096 #define TX_DEF_PENDING 127 @@ -765,7 +765,7 @@ static void sky2_wol_init(struct sky2_port *sky2) if (sky2->wol & WAKE_MAGIC) ctrl |= WOL_CTL_ENA_PME_ON_MAGIC_PKT|WOL_CTL_ENA_MAGIC_PKT_UNIT; else - ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT;; + ctrl |= WOL_CTL_DIS_PME_ON_MAGIC_PKT|WOL_CTL_DIS_MAGIC_PKT_UNIT; ctrl |= WOL_CTL_DIS_PME_ON_PATTERN|WOL_CTL_DIS_PATTERN_UNIT; sky2_write16(hw, WOL_REGS(port, WOL_CTRL_STAT), ctrl); @@ -1497,7 +1497,6 @@ static int sky2_up(struct net_device *dev) if (ramsize > 0) { u32 rxspace; - hw->flags |= SKY2_HW_RAM_BUFFER; pr_debug(PFX "%s: ram buffer %dK\n", dev->name, ramsize); if (ramsize < 16) rxspace = ramsize / 2; @@ -1567,11 +1566,13 @@ static unsigned tx_le_req(const struct sk_buff *skb) { unsigned count; - count = sizeof(dma_addr_t) / sizeof(u32); - count += skb_shinfo(skb)->nr_frags * count; + count = (skb_shinfo(skb)->nr_frags + 1) + * (sizeof(dma_addr_t) / sizeof(u32)); if (skb_is_gso(skb)) ++count; + else if (sizeof(dma_addr_t) == sizeof(u32)) + ++count; /* possible vlan */ if (skb->ip_summed == CHECKSUM_PARTIAL) ++count; @@ -2924,6 +2925,9 @@ static int __devinit sky2_init(struct sky2_hw *hw) ++hw->ports; } + if (sky2_read8(hw, B2_E_0)) + hw->flags |= SKY2_HW_RAM_BUFFER; + return 0; } @@ -4548,16 +4552,18 @@ static int __devinit sky2_probe(struct pci_dev *pdev, if (hw->ports > 1) { struct net_device *dev1; + err = -ENOMEM; dev1 = sky2_init_netdev(hw, 1, using_dac, wol_default); - if (!dev1) - dev_warn(&pdev->dev, "allocation for second device failed\n"); - else if ((err = register_netdev(dev1))) { + if (dev1 && (err = register_netdev(dev1)) == 0) + sky2_show_addr(dev1); + else { dev_warn(&pdev->dev, "register of second port failed (%d)\n", err); hw->dev[1] = NULL; - free_netdev(dev1); - } else - sky2_show_addr(dev1); + hw->ports = 1; + if (dev1) + free_netdev(dev1); + } } setup_timer(&hw->watchdog_timer, sky2_watchdog, (unsigned long) hw); diff --git a/drivers/net/slip.c b/drivers/net/slip.c index 26f6ee93a06..e17c535a577 100644 --- a/drivers/net/slip.c +++ b/drivers/net/slip.c @@ -616,6 +616,14 @@ static void sl_uninit(struct net_device *dev) sl_free_bufs(sl); } +/* Hook the destructor so we can free slip devices at the right point in time */ +static void sl_free_netdev(struct net_device *dev) +{ + int i = dev->base_addr; + free_netdev(dev); + slip_devs[i] = NULL; +} + static const struct net_device_ops sl_netdev_ops = { .ndo_init = sl_init, .ndo_uninit = sl_uninit, @@ -634,7 +642,7 @@ static const struct net_device_ops sl_netdev_ops = { static void sl_setup(struct net_device *dev) { dev->netdev_ops = &sl_netdev_ops; - dev->destructor = free_netdev; + dev->destructor = sl_free_netdev; dev->hard_header_len = 0; dev->addr_len = 0; @@ -712,8 +720,6 @@ static void sl_sync(void) static struct slip *sl_alloc(dev_t line) { int i; - int sel = -1; - int score = -1; struct net_device *dev = NULL; struct slip *sl; @@ -724,55 +730,7 @@ static struct slip *sl_alloc(dev_t line) dev = slip_devs[i]; if (dev == NULL) break; - - sl = netdev_priv(dev); - if (sl->leased) { - if (sl->line != line) - continue; - if (sl->tty) - return NULL; - - /* Clear ESCAPE & ERROR flags */ - sl->flags &= (1 << SLF_INUSE); - return sl; - } - - if (sl->tty) - continue; - - if (current->pid == sl->pid) { - if (sl->line == line && score < 3) { - sel = i; - score = 3; - continue; - } - if (score < 2) { - sel = i; - score = 2; - } - continue; - } - if (sl->line == line && score < 1) { - sel = i; - score = 1; - continue; - } - if (score < 0) { - sel = i; - score = 0; - } - } - - if (sel >= 0) { - i = sel; - dev = slip_devs[i]; - if (score > 1) { - sl = netdev_priv(dev); - sl->flags &= (1 << SLF_INUSE); - return sl; - } } - /* Sorry, too many, all slots in use */ if (i >= slip_maxdev) return NULL; @@ -909,30 +867,13 @@ err_exit: } /* - - FIXME: 1,2 are fixed 3 was never true anyway. - - Let me to blame a bit. - 1. TTY module calls this funstion on soft interrupt. - 2. TTY module calls this function WITH MASKED INTERRUPTS! - 3. TTY module does not notify us about line discipline - shutdown, - - Seems, now it is clean. The solution is to consider netdevice and - line discipline sides as two independent threads. - - By-product (not desired): sl? does not feel hangups and remains open. - It is supposed, that user level program (dip, diald, slattach...) - will catch SIGHUP and make the rest of work. - - I see no way to make more with current tty code. --ANK - */ - -/* * Close down a SLIP channel. * This means flushing out any pending queues, and then returning. This * call is serialized against other ldisc functions. + * + * We also use this method fo a hangup event */ + static void slip_close(struct tty_struct *tty) { struct slip *sl = tty->disc_data; @@ -951,10 +892,16 @@ static void slip_close(struct tty_struct *tty) del_timer_sync(&sl->keepalive_timer); del_timer_sync(&sl->outfill_timer); #endif - - /* Count references from TTY module */ + /* Flush network side */ + unregister_netdev(sl->dev); + /* This will complete via sl_free_netdev */ } +static int slip_hangup(struct tty_struct *tty) +{ + slip_close(tty); + return 0; +} /************************************************************************ * STANDARD SLIP ENCAPSULATION * ************************************************************************/ @@ -1311,6 +1258,7 @@ static struct tty_ldisc_ops sl_ldisc = { .name = "slip", .open = slip_open, .close = slip_close, + .hangup = slip_hangup, .ioctl = slip_ioctl, .receive_buf = slip_receive_buf, .write_wakeup = slip_write_wakeup, @@ -1384,6 +1332,8 @@ static void __exit slip_exit(void) } } while (busy && time_before(jiffies, timeout)); + /* FIXME: hangup is async so we should wait when doing this second + phase */ for (i = 0; i < slip_maxdev; i++) { dev = slip_devs[i]; diff --git a/drivers/net/smc91x.h b/drivers/net/smc91x.h index 784b631cfa3..3911be7c0cb 100644 --- a/drivers/net/smc91x.h +++ b/drivers/net/smc91x.h @@ -83,34 +83,6 @@ static inline void SMC_outw(u16 val, void __iomem *ioaddr, int reg) } } -#elif defined(CONFIG_BLACKFIN) - -#define SMC_IRQ_FLAGS IRQF_TRIGGER_HIGH -#define RPC_LSA_DEFAULT RPC_LED_100_10 -#define RPC_LSB_DEFAULT RPC_LED_TX_RX - -#define SMC_CAN_USE_8BIT 0 -#define SMC_CAN_USE_16BIT 1 -# if defined(CONFIG_BF561) -#define SMC_CAN_USE_32BIT 1 -# else -#define SMC_CAN_USE_32BIT 0 -# endif -#define SMC_IO_SHIFT 0 -#define SMC_NOWAIT 1 -#define SMC_USE_BFIN_DMA 0 - -#define SMC_inw(a, r) readw((a) + (r)) -#define SMC_outw(v, a, r) writew(v, (a) + (r)) -#define SMC_insw(a, r, p, l) readsw((a) + (r), p, l) -#define SMC_outsw(a, r, p, l) writesw((a) + (r), p, l) -# if SMC_CAN_USE_32BIT -#define SMC_inl(a, r) readl((a) + (r)) -#define SMC_outl(v, a, r) writel(v, (a) + (r)) -#define SMC_insl(a, r, p, l) readsl((a) + (r), p, l) -#define SMC_outsl(a, r, p, l) writesl((a) + (r), p, l) -# endif - #elif defined(CONFIG_REDWOOD_5) || defined(CONFIG_REDWOOD_6) /* We can only do 16-bit reads and writes in the static memory space. */ diff --git a/drivers/net/sunvnet.c b/drivers/net/sunvnet.c index f1e5e4542c2..bc74db0d12f 100644 --- a/drivers/net/sunvnet.c +++ b/drivers/net/sunvnet.c @@ -1016,7 +1016,6 @@ static const struct net_device_ops vnet_ops = { .ndo_open = vnet_open, .ndo_stop = vnet_close, .ndo_set_multicast_list = vnet_set_rx_mode, - .ndo_change_mtu = eth_change_mtu, .ndo_set_mac_address = vnet_set_mac_addr, .ndo_validate_addr = eth_validate_addr, .ndo_tx_timeout = vnet_tx_timeout, diff --git a/drivers/net/tun.c b/drivers/net/tun.c index 3f5d28851aa..4fdfa2ae541 100644 --- a/drivers/net/tun.c +++ b/drivers/net/tun.c @@ -946,8 +946,6 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr) char *name; unsigned long flags = 0; - err = -EINVAL; - if (!capable(CAP_NET_ADMIN)) return -EPERM; err = security_tun_dev_create(); @@ -964,7 +962,7 @@ static int tun_set_iff(struct net *net, struct file *file, struct ifreq *ifr) flags |= TUN_TAP_DEV; name = "tap%d"; } else - goto failed; + return -EINVAL; if (*ifr->ifr_name) name = ifr->ifr_name; @@ -1370,7 +1368,7 @@ static const struct file_operations tun_fops = { static struct miscdevice tun_miscdev = { .minor = TUN_MINOR, .name = "tun", - .devnode = "net/tun", + .nodename = "net/tun", .fops = &tun_fops, }; diff --git a/drivers/net/usb/cdc-phonet.c b/drivers/net/usb/cdc-phonet.c index 97e54d9d03c..33d5c579c5a 100644 --- a/drivers/net/usb/cdc-phonet.c +++ b/drivers/net/usb/cdc-phonet.c @@ -264,7 +264,6 @@ static int usbpn_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) switch (cmd) { case SIOCPNGAUTOCONF: req->ifr_phonet_autoconf.device = PN_DEV_PC; - printk(KERN_CRIT"device is PN_DEV_PC\n"); return 0; } return -ENOIOCTLCMD; diff --git a/drivers/net/usb/cdc_eem.c b/drivers/net/usb/cdc_eem.c index 45cebfb302c..23300656c26 100644 --- a/drivers/net/usb/cdc_eem.c +++ b/drivers/net/usb/cdc_eem.c @@ -300,20 +300,23 @@ static int eem_rx_fixup(struct usbnet *dev, struct sk_buff *skb) return 0; } - crc = get_unaligned_le32(skb2->data - + len - ETH_FCS_LEN); - skb_trim(skb2, len - ETH_FCS_LEN); - /* * The bmCRC helps to denote when the CRC field in * the Ethernet frame contains a calculated CRC: * bmCRC = 1 : CRC is calculated * bmCRC = 0 : CRC = 0xDEADBEEF */ - if (header & BIT(14)) - crc2 = ~crc32_le(~0, skb2->data, skb2->len); - else + if (header & BIT(14)) { + crc = get_unaligned_le32(skb2->data + + len - ETH_FCS_LEN); + crc2 = ~crc32_le(~0, skb2->data, skb2->len + - ETH_FCS_LEN); + } else { + crc = get_unaligned_be32(skb2->data + + len - ETH_FCS_LEN); crc2 = 0xdeadbeef; + } + skb_trim(skb2, len - ETH_FCS_LEN); if (is_last) return crc == crc2; diff --git a/drivers/net/usb/kaweth.c b/drivers/net/usb/kaweth.c index e2a39b9be96..e391ef969c2 100644 --- a/drivers/net/usb/kaweth.c +++ b/drivers/net/usb/kaweth.c @@ -263,6 +263,7 @@ static int kaweth_control(struct kaweth_device *kaweth, int timeout) { struct usb_ctrlrequest *dr; + int retval; dbg("kaweth_control()"); @@ -278,18 +279,21 @@ static int kaweth_control(struct kaweth_device *kaweth, return -ENOMEM; } - dr->bRequestType= requesttype; + dr->bRequestType = requesttype; dr->bRequest = request; dr->wValue = cpu_to_le16(value); dr->wIndex = cpu_to_le16(index); dr->wLength = cpu_to_le16(size); - return kaweth_internal_control_msg(kaweth->dev, - pipe, - dr, - data, - size, - timeout); + retval = kaweth_internal_control_msg(kaweth->dev, + pipe, + dr, + data, + size, + timeout); + + kfree(dr); + return retval; } /**************************************************************** diff --git a/drivers/net/usb/smsc95xx.c b/drivers/net/usb/smsc95xx.c index 938fb3530a7..c6c922247d0 100644 --- a/drivers/net/usb/smsc95xx.c +++ b/drivers/net/usb/smsc95xx.c @@ -1227,7 +1227,7 @@ static const struct driver_info smsc95xx_info = { .rx_fixup = smsc95xx_rx_fixup, .tx_fixup = smsc95xx_tx_fixup, .status = smsc95xx_status, - .flags = FLAG_ETHER, + .flags = FLAG_ETHER | FLAG_SEND_ZLP, }; static const struct usb_device_id products[] = { @@ -1237,10 +1237,75 @@ static const struct usb_device_id products[] = { .driver_info = (unsigned long) &smsc95xx_info, }, { + /* SMSC9505 USB Ethernet Device */ + USB_DEVICE(0x0424, 0x9505), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9500A USB Ethernet Device */ + USB_DEVICE(0x0424, 0x9E00), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9505A USB Ethernet Device */ + USB_DEVICE(0x0424, 0x9E01), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { /* SMSC9512/9514 USB Hub & Ethernet Device */ USB_DEVICE(0x0424, 0xec00), .driver_info = (unsigned long) &smsc95xx_info, }, + { + /* SMSC9500 USB Ethernet Device (SAL10) */ + USB_DEVICE(0x0424, 0x9900), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9505 USB Ethernet Device (SAL10) */ + USB_DEVICE(0x0424, 0x9901), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9500A USB Ethernet Device (SAL10) */ + USB_DEVICE(0x0424, 0x9902), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9505A USB Ethernet Device (SAL10) */ + USB_DEVICE(0x0424, 0x9903), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9512/9514 USB Hub & Ethernet Device (SAL10) */ + USB_DEVICE(0x0424, 0x9904), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9500A USB Ethernet Device (HAL) */ + USB_DEVICE(0x0424, 0x9905), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9505A USB Ethernet Device (HAL) */ + USB_DEVICE(0x0424, 0x9906), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9500 USB Ethernet Device (Alternate ID) */ + USB_DEVICE(0x0424, 0x9907), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9500A USB Ethernet Device (Alternate ID) */ + USB_DEVICE(0x0424, 0x9908), + .driver_info = (unsigned long) &smsc95xx_info, + }, + { + /* SMSC9512/9514 USB Hub & Ethernet Device (Alternate ID) */ + USB_DEVICE(0x0424, 0x9909), + .driver_info = (unsigned long) &smsc95xx_info, + }, { }, /* END */ }; MODULE_DEVICE_TABLE(usb, products); diff --git a/drivers/net/usb/usbnet.c b/drivers/net/usb/usbnet.c index 24b36f79515..ca5ca5ae061 100644 --- a/drivers/net/usb/usbnet.c +++ b/drivers/net/usb/usbnet.c @@ -1049,7 +1049,7 @@ netdev_tx_t usbnet_start_xmit (struct sk_buff *skb, * NOTE: strictly conforming cdc-ether devices should expect * the ZLP here, but ignore the one-byte packet. */ - if ((length % dev->maxpacket) == 0) { + if (!(info->flags & FLAG_SEND_ZLP) && (length % dev->maxpacket) == 0) { urb->transfer_buffer_length++; if (skb_tailroom(skb)) { skb->data[skb->len] = 0; diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c index 32266fb89c2..d445845f277 100644 --- a/drivers/net/virtio_net.c +++ b/drivers/net/virtio_net.c @@ -1,4 +1,4 @@ -/* A simple network driver using virtio. +/* A network driver using virtio. * * Copyright 2007 Rusty Russell <rusty@rustcorp.com.au> IBM Corporation * @@ -22,6 +22,7 @@ #include <linux/ethtool.h> #include <linux/module.h> #include <linux/virtio.h> +#include <linux/virtio_ids.h> #include <linux/virtio_net.h> #include <linux/scatterlist.h> #include <linux/if_vlan.h> @@ -47,19 +48,9 @@ struct virtnet_info struct napi_struct napi; unsigned int status; - /* The skb we couldn't send because buffers were full. */ - struct sk_buff *last_xmit_skb; - - /* If we need to free in a timer, this is it. */ - struct timer_list xmit_free_timer; - /* Number of input buffers, and max we've ever had. */ unsigned int num, max; - /* For cleaning up after transmission. */ - struct tasklet_struct tasklet; - bool free_in_tasklet; - /* I like... big packets and I cannot lie! */ bool big_packets; @@ -77,9 +68,17 @@ struct virtnet_info struct page *pages; }; -static inline void *skb_vnet_hdr(struct sk_buff *skb) +struct skb_vnet_hdr { + union { + struct virtio_net_hdr hdr; + struct virtio_net_hdr_mrg_rxbuf mhdr; + }; + unsigned int num_sg; +}; + +static inline struct skb_vnet_hdr *skb_vnet_hdr(struct sk_buff *skb) { - return (struct virtio_net_hdr *)skb->cb; + return (struct skb_vnet_hdr *)skb->cb; } static void give_a_page(struct virtnet_info *vi, struct page *page) @@ -118,17 +117,13 @@ static void skb_xmit_done(struct virtqueue *svq) /* We were probably waiting for more output buffers. */ netif_wake_queue(vi->dev); - - /* Make sure we re-xmit last_xmit_skb: if there are no more packets - * queued, start_xmit won't be called. */ - tasklet_schedule(&vi->tasklet); } static void receive_skb(struct net_device *dev, struct sk_buff *skb, unsigned len) { struct virtnet_info *vi = netdev_priv(dev); - struct virtio_net_hdr *hdr = skb_vnet_hdr(skb); + struct skb_vnet_hdr *hdr = skb_vnet_hdr(skb); int err; int i; @@ -139,7 +134,6 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, } if (vi->mergeable_rx_bufs) { - struct virtio_net_hdr_mrg_rxbuf *mhdr = skb_vnet_hdr(skb); unsigned int copy; char *p = page_address(skb_shinfo(skb)->frags[0].page); @@ -147,8 +141,8 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, len = PAGE_SIZE; len -= sizeof(struct virtio_net_hdr_mrg_rxbuf); - memcpy(hdr, p, sizeof(*mhdr)); - p += sizeof(*mhdr); + memcpy(&hdr->mhdr, p, sizeof(hdr->mhdr)); + p += sizeof(hdr->mhdr); copy = len; if (copy > skb_tailroom(skb)) @@ -163,13 +157,13 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, skb_shinfo(skb)->nr_frags--; } else { skb_shinfo(skb)->frags[0].page_offset += - sizeof(*mhdr) + copy; + sizeof(hdr->mhdr) + copy; skb_shinfo(skb)->frags[0].size = len; skb->data_len += len; skb->len += len; } - while (--mhdr->num_buffers) { + while (--hdr->mhdr.num_buffers) { struct sk_buff *nskb; i = skb_shinfo(skb)->nr_frags; @@ -183,7 +177,7 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, nskb = vi->rvq->vq_ops->get_buf(vi->rvq, &len); if (!nskb) { pr_debug("%s: rx error: %d buffers missing\n", - dev->name, mhdr->num_buffers); + dev->name, hdr->mhdr.num_buffers); dev->stats.rx_length_errors++; goto drop; } @@ -204,7 +198,7 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, skb->len += len; } } else { - len -= sizeof(struct virtio_net_hdr); + len -= sizeof(hdr->hdr); if (len <= MAX_PACKET_LEN) trim_pages(vi, skb); @@ -222,9 +216,11 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, dev->stats.rx_bytes += skb->len; dev->stats.rx_packets++; - if (hdr->flags & VIRTIO_NET_HDR_F_NEEDS_CSUM) { + if (hdr->hdr.flags & VIRTIO_NET_HDR_F_NEEDS_CSUM) { pr_debug("Needs csum!\n"); - if (!skb_partial_csum_set(skb,hdr->csum_start,hdr->csum_offset)) + if (!skb_partial_csum_set(skb, + hdr->hdr.csum_start, + hdr->hdr.csum_offset)) goto frame_err; } @@ -232,9 +228,9 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, pr_debug("Receiving skb proto 0x%04x len %i type %i\n", ntohs(skb->protocol), skb->len, skb->pkt_type); - if (hdr->gso_type != VIRTIO_NET_HDR_GSO_NONE) { + if (hdr->hdr.gso_type != VIRTIO_NET_HDR_GSO_NONE) { pr_debug("GSO!\n"); - switch (hdr->gso_type & ~VIRTIO_NET_HDR_GSO_ECN) { + switch (hdr->hdr.gso_type & ~VIRTIO_NET_HDR_GSO_ECN) { case VIRTIO_NET_HDR_GSO_TCPV4: skb_shinfo(skb)->gso_type = SKB_GSO_TCPV4; break; @@ -247,14 +243,14 @@ static void receive_skb(struct net_device *dev, struct sk_buff *skb, default: if (net_ratelimit()) printk(KERN_WARNING "%s: bad gso type %u.\n", - dev->name, hdr->gso_type); + dev->name, hdr->hdr.gso_type); goto frame_err; } - if (hdr->gso_type & VIRTIO_NET_HDR_GSO_ECN) + if (hdr->hdr.gso_type & VIRTIO_NET_HDR_GSO_ECN) skb_shinfo(skb)->gso_type |= SKB_GSO_TCP_ECN; - skb_shinfo(skb)->gso_size = hdr->gso_size; + skb_shinfo(skb)->gso_size = hdr->hdr.gso_size; if (skb_shinfo(skb)->gso_size == 0) { if (net_ratelimit()) printk(KERN_WARNING "%s: zero gso size.\n", @@ -284,8 +280,8 @@ static bool try_fill_recv_maxbufs(struct virtnet_info *vi, gfp_t gfp) bool oom = false; sg_init_table(sg, 2+MAX_SKB_FRAGS); - for (;;) { - struct virtio_net_hdr *hdr; + do { + struct skb_vnet_hdr *hdr; skb = netdev_alloc_skb(vi->dev, MAX_PACKET_LEN + NET_IP_ALIGN); if (unlikely(!skb)) { @@ -297,7 +293,7 @@ static bool try_fill_recv_maxbufs(struct virtnet_info *vi, gfp_t gfp) skb_put(skb, MAX_PACKET_LEN); hdr = skb_vnet_hdr(skb); - sg_set_buf(sg, hdr, sizeof(*hdr)); + sg_set_buf(sg, &hdr->hdr, sizeof(hdr->hdr)); if (vi->big_packets) { for (i = 0; i < MAX_SKB_FRAGS; i++) { @@ -320,14 +316,14 @@ static bool try_fill_recv_maxbufs(struct virtnet_info *vi, gfp_t gfp) skb_queue_head(&vi->recv, skb); err = vi->rvq->vq_ops->add_buf(vi->rvq, sg, 0, num, skb); - if (err) { + if (err < 0) { skb_unlink(skb, &vi->recv); trim_pages(vi, skb); kfree_skb(skb); break; } vi->num++; - } + } while (err >= num); if (unlikely(vi->num > vi->max)) vi->max = vi->num; vi->rvq->vq_ops->kick(vi->rvq); @@ -345,7 +341,7 @@ static bool try_fill_recv(struct virtnet_info *vi, gfp_t gfp) if (!vi->mergeable_rx_bufs) return try_fill_recv_maxbufs(vi, gfp); - for (;;) { + do { skb_frag_t *f; skb = netdev_alloc_skb(vi->dev, GOOD_COPY_LEN + NET_IP_ALIGN); @@ -373,13 +369,13 @@ static bool try_fill_recv(struct virtnet_info *vi, gfp_t gfp) skb_queue_head(&vi->recv, skb); err = vi->rvq->vq_ops->add_buf(vi->rvq, sg, 0, 1, skb); - if (err) { + if (err < 0) { skb_unlink(skb, &vi->recv); kfree_skb(skb); break; } vi->num++; - } + } while (err > 0); if (unlikely(vi->num > vi->max)) vi->max = vi->num; vi->rvq->vq_ops->kick(vi->rvq); @@ -447,42 +443,26 @@ again: return received; } -static void free_old_xmit_skbs(struct virtnet_info *vi) +static unsigned int free_old_xmit_skbs(struct virtnet_info *vi) { struct sk_buff *skb; - unsigned int len; + unsigned int len, tot_sgs = 0; while ((skb = vi->svq->vq_ops->get_buf(vi->svq, &len)) != NULL) { pr_debug("Sent skb %p\n", skb); __skb_unlink(skb, &vi->send); vi->dev->stats.tx_bytes += skb->len; vi->dev->stats.tx_packets++; + tot_sgs += skb_vnet_hdr(skb)->num_sg; kfree_skb(skb); } -} - -/* If the virtio transport doesn't always notify us when all in-flight packets - * are consumed, we fall back to using this function on a timer to free them. */ -static void xmit_free(unsigned long data) -{ - struct virtnet_info *vi = (void *)data; - - netif_tx_lock(vi->dev); - - free_old_xmit_skbs(vi); - - if (!skb_queue_empty(&vi->send)) - mod_timer(&vi->xmit_free_timer, jiffies + (HZ/10)); - - netif_tx_unlock(vi->dev); + return tot_sgs; } static int xmit_skb(struct virtnet_info *vi, struct sk_buff *skb) { - int num, err; struct scatterlist sg[2+MAX_SKB_FRAGS]; - struct virtio_net_hdr_mrg_rxbuf *mhdr = skb_vnet_hdr(skb); - struct virtio_net_hdr *hdr = skb_vnet_hdr(skb); + struct skb_vnet_hdr *hdr = skb_vnet_hdr(skb); const unsigned char *dest = ((struct ethhdr *)skb->data)->h_dest; sg_init_table(sg, 2+MAX_SKB_FRAGS); @@ -490,108 +470,89 @@ static int xmit_skb(struct virtnet_info *vi, struct sk_buff *skb) pr_debug("%s: xmit %p %pM\n", vi->dev->name, skb, dest); if (skb->ip_summed == CHECKSUM_PARTIAL) { - hdr->flags = VIRTIO_NET_HDR_F_NEEDS_CSUM; - hdr->csum_start = skb->csum_start - skb_headroom(skb); - hdr->csum_offset = skb->csum_offset; + hdr->hdr.flags = VIRTIO_NET_HDR_F_NEEDS_CSUM; + hdr->hdr.csum_start = skb->csum_start - skb_headroom(skb); + hdr->hdr.csum_offset = skb->csum_offset; } else { - hdr->flags = 0; - hdr->csum_offset = hdr->csum_start = 0; + hdr->hdr.flags = 0; + hdr->hdr.csum_offset = hdr->hdr.csum_start = 0; } if (skb_is_gso(skb)) { - hdr->hdr_len = skb_headlen(skb); - hdr->gso_size = skb_shinfo(skb)->gso_size; + hdr->hdr.hdr_len = skb_headlen(skb); + hdr->hdr.gso_size = skb_shinfo(skb)->gso_size; if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV4) - hdr->gso_type = VIRTIO_NET_HDR_GSO_TCPV4; + hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_TCPV4; else if (skb_shinfo(skb)->gso_type & SKB_GSO_TCPV6) - hdr->gso_type = VIRTIO_NET_HDR_GSO_TCPV6; + hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_TCPV6; else if (skb_shinfo(skb)->gso_type & SKB_GSO_UDP) - hdr->gso_type = VIRTIO_NET_HDR_GSO_UDP; + hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_UDP; else BUG(); if (skb_shinfo(skb)->gso_type & SKB_GSO_TCP_ECN) - hdr->gso_type |= VIRTIO_NET_HDR_GSO_ECN; + hdr->hdr.gso_type |= VIRTIO_NET_HDR_GSO_ECN; } else { - hdr->gso_type = VIRTIO_NET_HDR_GSO_NONE; - hdr->gso_size = hdr->hdr_len = 0; + hdr->hdr.gso_type = VIRTIO_NET_HDR_GSO_NONE; + hdr->hdr.gso_size = hdr->hdr.hdr_len = 0; } - mhdr->num_buffers = 0; + hdr->mhdr.num_buffers = 0; /* Encode metadata header at front. */ if (vi->mergeable_rx_bufs) - sg_set_buf(sg, mhdr, sizeof(*mhdr)); + sg_set_buf(sg, &hdr->mhdr, sizeof(hdr->mhdr)); else - sg_set_buf(sg, hdr, sizeof(*hdr)); - - num = skb_to_sgvec(skb, sg+1, 0, skb->len) + 1; - - err = vi->svq->vq_ops->add_buf(vi->svq, sg, num, 0, skb); - if (!err && !vi->free_in_tasklet) - mod_timer(&vi->xmit_free_timer, jiffies + (HZ/10)); + sg_set_buf(sg, &hdr->hdr, sizeof(hdr->hdr)); - return err; -} - -static void xmit_tasklet(unsigned long data) -{ - struct virtnet_info *vi = (void *)data; - - netif_tx_lock_bh(vi->dev); - if (vi->last_xmit_skb && xmit_skb(vi, vi->last_xmit_skb) == 0) { - vi->svq->vq_ops->kick(vi->svq); - vi->last_xmit_skb = NULL; - } - if (vi->free_in_tasklet) - free_old_xmit_skbs(vi); - netif_tx_unlock_bh(vi->dev); + hdr->num_sg = skb_to_sgvec(skb, sg+1, 0, skb->len) + 1; + return vi->svq->vq_ops->add_buf(vi->svq, sg, hdr->num_sg, 0, skb); } static netdev_tx_t start_xmit(struct sk_buff *skb, struct net_device *dev) { struct virtnet_info *vi = netdev_priv(dev); + int capacity; again: /* Free up any pending old buffers before queueing new ones. */ free_old_xmit_skbs(vi); - /* If we has a buffer left over from last time, send it now. */ - if (unlikely(vi->last_xmit_skb) && - xmit_skb(vi, vi->last_xmit_skb) != 0) - goto stop_queue; - - vi->last_xmit_skb = NULL; - /* Put new one in send queue and do transmit */ - if (likely(skb)) { - __skb_queue_head(&vi->send, skb); - if (xmit_skb(vi, skb) != 0) { - vi->last_xmit_skb = skb; - skb = NULL; - goto stop_queue; + __skb_queue_head(&vi->send, skb); + capacity = xmit_skb(vi, skb); + + /* This can happen with OOM and indirect buffers. */ + if (unlikely(capacity < 0)) { + netif_stop_queue(dev); + dev_warn(&dev->dev, "Unexpected full queue\n"); + if (unlikely(!vi->svq->vq_ops->enable_cb(vi->svq))) { + vi->svq->vq_ops->disable_cb(vi->svq); + netif_start_queue(dev); + goto again; } + return NETDEV_TX_BUSY; } -done: - vi->svq->vq_ops->kick(vi->svq); - return NETDEV_TX_OK; -stop_queue: - pr_debug("%s: virtio not prepared to send\n", dev->name); - netif_stop_queue(dev); - - /* Activate callback for using skbs: if this returns false it - * means some were used in the meantime. */ - if (unlikely(!vi->svq->vq_ops->enable_cb(vi->svq))) { - vi->svq->vq_ops->disable_cb(vi->svq); - netif_start_queue(dev); - goto again; - } - if (skb) { - /* Drop this skb: we only queue one. */ - vi->dev->stats.tx_dropped++; - kfree_skb(skb); + vi->svq->vq_ops->kick(vi->svq); + /* Don't wait up for transmitted skbs to be freed. */ + skb_orphan(skb); + nf_reset(skb); + + /* Apparently nice girls don't return TX_BUSY; stop the queue + * before it gets out of hand. Naturally, this wastes entries. */ + if (capacity < 2+MAX_SKB_FRAGS) { + netif_stop_queue(dev); + if (unlikely(!vi->svq->vq_ops->enable_cb(vi->svq))) { + /* More just got used, free them then recheck. */ + capacity += free_old_xmit_skbs(vi); + if (capacity >= 2+MAX_SKB_FRAGS) { + netif_start_queue(dev); + vi->svq->vq_ops->disable_cb(vi->svq); + } + } } - goto done; + + return NETDEV_TX_OK; } static int virtnet_set_mac_address(struct net_device *dev, void *p) @@ -668,7 +629,7 @@ static bool virtnet_send_command(struct virtnet_info *vi, u8 class, u8 cmd, sg_set_buf(&sg[i + 1], sg_virt(s), s->length); sg_set_buf(&sg[out + in - 1], &status, sizeof(status)); - BUG_ON(vi->cvq->vq_ops->add_buf(vi->cvq, sg, out, in, vi)); + BUG_ON(vi->cvq->vq_ops->add_buf(vi->cvq, sg, out, in, vi) < 0); vi->cvq->vq_ops->kick(vi->cvq); @@ -924,10 +885,6 @@ static int virtnet_probe(struct virtio_device *vdev) vi->pages = NULL; INIT_DELAYED_WORK(&vi->refill, refill_work); - /* If they give us a callback when all buffers are done, we don't need - * the timer. */ - vi->free_in_tasklet = virtio_has_feature(vdev,VIRTIO_F_NOTIFY_ON_EMPTY); - /* If we can receive ANY GSO packets, we must allocate large ones. */ if (virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_TSO4) || virtio_has_feature(vdev, VIRTIO_NET_F_GUEST_TSO6) @@ -959,11 +916,6 @@ static int virtnet_probe(struct virtio_device *vdev) skb_queue_head_init(&vi->recv); skb_queue_head_init(&vi->send); - tasklet_init(&vi->tasklet, xmit_tasklet, (unsigned long)vi); - - if (!vi->free_in_tasklet) - setup_timer(&vi->xmit_free_timer, xmit_free, (unsigned long)vi); - err = register_netdev(dev); if (err) { pr_debug("virtio_net: registering device failed\n"); @@ -1004,9 +956,6 @@ static void virtnet_remove(struct virtio_device *vdev) /* Stop all the virtqueues. */ vdev->config->reset(vdev); - if (!vi->free_in_tasklet) - del_timer_sync(&vi->xmit_free_timer); - /* Free our skbs in send and recv queues, if any. */ while ((skb = __skb_dequeue(&vi->recv)) != NULL) { kfree_skb(skb); @@ -1040,7 +989,6 @@ static unsigned int features[] = { VIRTIO_NET_F_GUEST_ECN, VIRTIO_NET_F_GUEST_UFO, VIRTIO_NET_F_MRG_RXBUF, VIRTIO_NET_F_STATUS, VIRTIO_NET_F_CTRL_VQ, VIRTIO_NET_F_CTRL_RX, VIRTIO_NET_F_CTRL_VLAN, - VIRTIO_F_NOTIFY_ON_EMPTY, }; static struct virtio_driver virtio_net = { diff --git a/drivers/net/vxge/vxge-config.h b/drivers/net/vxge/vxge-config.h index 62779a520ca..3e94f0ce090 100644 --- a/drivers/net/vxge/vxge-config.h +++ b/drivers/net/vxge/vxge-config.h @@ -1541,7 +1541,7 @@ void vxge_hw_ring_rxd_1b_info_get( rxd_info->l4_cksum_valid = (u32)VXGE_HW_RING_RXD_L4_CKSUM_CORRECT_GET(rxdp->control_0); rxd_info->l4_cksum = - (u32)VXGE_HW_RING_RXD_L4_CKSUM_GET(rxdp->control_0);; + (u32)VXGE_HW_RING_RXD_L4_CKSUM_GET(rxdp->control_0); rxd_info->frame = (u32)VXGE_HW_RING_RXD_ETHER_ENCAP_GET(rxdp->control_0); rxd_info->proto = diff --git a/drivers/net/vxge/vxge-main.c b/drivers/net/vxge/vxge-main.c index b378037a29b..068d7a9d3e3 100644 --- a/drivers/net/vxge/vxge-main.c +++ b/drivers/net/vxge/vxge-main.c @@ -2350,7 +2350,7 @@ static int vxge_enable_msix(struct vxgedev *vdev) enum vxge_hw_status status; /* 0 - Tx, 1 - Rx */ int tim_msix_id[4]; - int alarm_msix_id = 0, msix_intr_vect = 0;; + int alarm_msix_id = 0, msix_intr_vect = 0; vdev->intr_cnt = 0; /* allocate msix vectors */ diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig index ad89d23968d..49ea9c92b7e 100644 --- a/drivers/net/wireless/Kconfig +++ b/drivers/net/wireless/Kconfig @@ -5,6 +5,7 @@ menuconfig WLAN bool "Wireless LAN" depends on !S390 + default y ---help--- This section contains all the pre 802.11 and 802.11 wireless device drivers. For a complete list of drivers and documentation diff --git a/drivers/net/wireless/arlan-proc.c b/drivers/net/wireless/arlan-proc.c index 2ab1d59870f..a8b689635a3 100644 --- a/drivers/net/wireless/arlan-proc.c +++ b/drivers/net/wireless/arlan-proc.c @@ -402,7 +402,7 @@ static int arlan_setup_card_by_book(struct net_device *dev) static char arlan_drive_info[ARLAN_STR_SIZE] = "A655\n\0"; -static int arlan_sysctl_info(ctl_table * ctl, int write, struct file *filp, +static int arlan_sysctl_info(ctl_table * ctl, int write, void __user *buffer, size_t * lenp, loff_t *ppos) { int i; @@ -629,7 +629,7 @@ final: *lenp = pos; if (!write) - retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos); + retv = proc_dostring(ctl, write, buffer, lenp, ppos); else { *lenp = 0; @@ -639,7 +639,7 @@ final: } -static int arlan_sysctl_info161719(ctl_table * ctl, int write, struct file *filp, +static int arlan_sysctl_info161719(ctl_table * ctl, int write, void __user *buffer, size_t * lenp, loff_t *ppos) { int i; @@ -669,11 +669,11 @@ static int arlan_sysctl_info161719(ctl_table * ctl, int write, struct file *filp final: *lenp = pos; - retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos); + retv = proc_dostring(ctl, write, buffer, lenp, ppos); return retv; } -static int arlan_sysctl_infotxRing(ctl_table * ctl, int write, struct file *filp, +static int arlan_sysctl_infotxRing(ctl_table * ctl, int write, void __user *buffer, size_t * lenp, loff_t *ppos) { int i; @@ -698,11 +698,11 @@ static int arlan_sysctl_infotxRing(ctl_table * ctl, int write, struct file *filp SARLBNpln(u_char, txBuffer, 0x800); final: *lenp = pos; - retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos); + retv = proc_dostring(ctl, write, buffer, lenp, ppos); return retv; } -static int arlan_sysctl_inforxRing(ctl_table * ctl, int write, struct file *filp, +static int arlan_sysctl_inforxRing(ctl_table * ctl, int write, void __user *buffer, size_t * lenp, loff_t *ppos) { int i; @@ -726,11 +726,11 @@ static int arlan_sysctl_inforxRing(ctl_table * ctl, int write, struct file *filp SARLBNpln(u_char, rxBuffer, 0x800); final: *lenp = pos; - retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos); + retv = proc_dostring(ctl, write, buffer, lenp, ppos); return retv; } -static int arlan_sysctl_info18(ctl_table * ctl, int write, struct file *filp, +static int arlan_sysctl_info18(ctl_table * ctl, int write, void __user *buffer, size_t * lenp, loff_t *ppos) { int i; @@ -756,7 +756,7 @@ static int arlan_sysctl_info18(ctl_table * ctl, int write, struct file *filp, final: *lenp = pos; - retv = proc_dostring(ctl, write, filp, buffer, lenp, ppos); + retv = proc_dostring(ctl, write, buffer, lenp, ppos); return retv; } @@ -766,7 +766,7 @@ final: static char conf_reset_result[200]; -static int arlan_configure(ctl_table * ctl, int write, struct file *filp, +static int arlan_configure(ctl_table * ctl, int write, void __user *buffer, size_t * lenp, loff_t *ppos) { int pos = 0; @@ -788,10 +788,10 @@ static int arlan_configure(ctl_table * ctl, int write, struct file *filp, return -1; *lenp = pos; - return proc_dostring(ctl, write, filp, buffer, lenp, ppos); + return proc_dostring(ctl, write, buffer, lenp, ppos); } -static int arlan_sysctl_reset(ctl_table * ctl, int write, struct file *filp, +static int arlan_sysctl_reset(ctl_table * ctl, int write, void __user *buffer, size_t * lenp, loff_t *ppos) { int pos = 0; @@ -811,7 +811,7 @@ static int arlan_sysctl_reset(ctl_table * ctl, int write, struct file *filp, } else return -1; *lenp = pos + 3; - return proc_dostring(ctl, write, filp, buffer, lenp, ppos); + return proc_dostring(ctl, write, buffer, lenp, ppos); } diff --git a/drivers/net/wireless/ath/ar9170/usb.c b/drivers/net/wireless/ath/ar9170/usb.c index e0138ac8bf5..e974e5829e1 100644 --- a/drivers/net/wireless/ath/ar9170/usb.c +++ b/drivers/net/wireless/ath/ar9170/usb.c @@ -64,6 +64,8 @@ static struct usb_device_id ar9170_usb_ids[] = { { USB_DEVICE(0x0cf3, 0x9170) }, /* Atheros TG121N */ { USB_DEVICE(0x0cf3, 0x1001) }, + /* TP-Link TL-WN821N v2 */ + { USB_DEVICE(0x0cf3, 0x1002) }, /* Cace Airpcap NX */ { USB_DEVICE(0xcace, 0x0300) }, /* D-Link DWA 160A */ diff --git a/drivers/net/wireless/ath/ath5k/reg.h b/drivers/net/wireless/ath/ath5k/reg.h index debad07d990..c63ea6afd96 100644 --- a/drivers/net/wireless/ath/ath5k/reg.h +++ b/drivers/net/wireless/ath/ath5k/reg.h @@ -982,7 +982,7 @@ #define AR5K_5414_CBCFG_BUF_DIS 0x10 /* Disable buffer */ /* - * PCI-E Power managment configuration + * PCI-E Power management configuration * and status register [5424+] */ #define AR5K_PCIE_PM_CTL 0x4068 /* Register address */ diff --git a/drivers/net/wireless/ath/ath9k/ani.c b/drivers/net/wireless/ath/ath9k/ani.c index a7cbb07988c..2b493742ef1 100644 --- a/drivers/net/wireless/ath/ath9k/ani.c +++ b/drivers/net/wireless/ath/ath9k/ani.c @@ -327,7 +327,8 @@ static void ath9k_hw_ani_ofdm_err_trigger(struct ath_hw *ah) aniState->firstepLevel + 1); return; } else { - if (conf->channel->band == IEEE80211_BAND_2GHZ) { + if ((conf->channel->band == IEEE80211_BAND_2GHZ) && + !conf_is_ht(conf)) { if (!aniState->ofdmWeakSigDetectOff) ath9k_hw_ani_control(ah, ATH9K_ANI_OFDM_WEAK_SIGNAL_DETECTION, @@ -369,7 +370,8 @@ static void ath9k_hw_ani_cck_err_trigger(struct ath_hw *ah) ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL, aniState->firstepLevel + 1); } else { - if (conf->channel->band == IEEE80211_BAND_2GHZ) { + if ((conf->channel->band == IEEE80211_BAND_2GHZ) && + !conf_is_ht(conf)) { if (aniState->firstepLevel > 0) ath9k_hw_ani_control(ah, ATH9K_ANI_FIRSTEP_LEVEL, 0); diff --git a/drivers/net/wireless/ath/ath9k/calib.c b/drivers/net/wireless/ath/ath9k/calib.c index 3234995e888..0ad6d0b76e9 100644 --- a/drivers/net/wireless/ath/ath9k/calib.c +++ b/drivers/net/wireless/ath/ath9k/calib.c @@ -609,14 +609,24 @@ void ath9k_hw_loadnf(struct ath_hw *ah, struct ath9k_channel *chan) AR_PHY_CH1_EXT_CCA, AR_PHY_CH2_EXT_CCA }; - u8 chainmask; + u8 chainmask, rx_chain_status; + rx_chain_status = REG_READ(ah, AR_PHY_RX_CHAINMASK); if (AR_SREV_9285(ah)) chainmask = 0x9; - else if (AR_SREV_9280(ah) || AR_SREV_9287(ah)) - chainmask = 0x1B; - else - chainmask = 0x3F; + else if (AR_SREV_9280(ah) || AR_SREV_9287(ah)) { + if ((rx_chain_status & 0x2) || (rx_chain_status & 0x4)) + chainmask = 0x1B; + else + chainmask = 0x09; + } else { + if (rx_chain_status & 0x4) + chainmask = 0x3F; + else if (rx_chain_status & 0x2) + chainmask = 0x1B; + else + chainmask = 0x09; + } h = ah->nfCalHist; @@ -697,6 +707,8 @@ void ath9k_init_nfcal_hist_buffer(struct ath_hw *ah) noise_floor = AR_PHY_CCA_MAX_AR9280_GOOD_VALUE; else if (AR_SREV_9285(ah)) noise_floor = AR_PHY_CCA_MAX_AR9285_GOOD_VALUE; + else if (AR_SREV_9287(ah)) + noise_floor = AR_PHY_CCA_MAX_AR9287_GOOD_VALUE; else noise_floor = AR_PHY_CCA_MAX_AR5416_GOOD_VALUE; @@ -924,6 +936,7 @@ static inline void ath9k_hw_9285_pa_cal(struct ath_hw *ah, bool is_reset) regVal |= (1 << (19 + i)); REG_WRITE(ah, 0x7834, regVal); udelay(1); + regVal = REG_READ(ah, 0x7834); regVal &= (~(0x1 << (19 + i))); reg_field = MS(REG_READ(ah, 0x7840), AR9285_AN_RXTXBB1_SPARE9); regVal |= (reg_field << (19 + i)); diff --git a/drivers/net/wireless/ath/ath9k/calib.h b/drivers/net/wireless/ath/ath9k/calib.h index 019bcbba40e..9028ab193e4 100644 --- a/drivers/net/wireless/ath/ath9k/calib.h +++ b/drivers/net/wireless/ath/ath9k/calib.h @@ -28,6 +28,7 @@ extern const struct ath9k_percal_data adc_init_dc_cal; #define AR_PHY_CCA_MAX_AR5416_GOOD_VALUE -85 #define AR_PHY_CCA_MAX_AR9280_GOOD_VALUE -112 #define AR_PHY_CCA_MAX_AR9285_GOOD_VALUE -118 +#define AR_PHY_CCA_MAX_AR9287_GOOD_VALUE -118 #define AR_PHY_CCA_MAX_HIGH_VALUE -62 #define AR_PHY_CCA_MIN_BAD_VALUE -140 #define AR_PHY_CCA_FILTERWINDOW_LENGTH_INIT 3 diff --git a/drivers/net/wireless/ath/ath9k/eeprom_def.c b/drivers/net/wireless/ath/ath9k/eeprom_def.c index ae7fb5dcb26..4071fc91da0 100644 --- a/drivers/net/wireless/ath/ath9k/eeprom_def.c +++ b/drivers/net/wireless/ath/ath9k/eeprom_def.c @@ -509,6 +509,8 @@ static void ath9k_hw_def_set_board_values(struct ath_hw *ah, REG_RMW_FIELD(ah, AR_AN_TOP1, AR_AN_TOP1_DACIPMODE, eep->baseEepHeader.dacLpMode); + udelay(100); + REG_RMW_FIELD(ah, AR_PHY_FRAME_CTL, AR_PHY_FRAME_CTL_TX_CLIP, pModal->miscBits >> 2); @@ -902,7 +904,7 @@ static void ath9k_hw_set_def_power_per_rate_table(struct ath_hw *ah, u16 powerLimit) { #define REDUCE_SCALED_POWER_BY_TWO_CHAIN 6 /* 10*log10(2)*2 */ -#define REDUCE_SCALED_POWER_BY_THREE_CHAIN 10 /* 10*log10(3)*2 */ +#define REDUCE_SCALED_POWER_BY_THREE_CHAIN 9 /* 10*log10(3)*2 */ struct ath_regulatory *regulatory = ath9k_hw_regulatory(ah); struct ar5416_eeprom_def *pEepData = &ah->eeprom.def; diff --git a/drivers/net/wireless/ath/ath9k/hw.c b/drivers/net/wireless/ath/ath9k/hw.c index b6c6cca0781..ca7694caf36 100644 --- a/drivers/net/wireless/ath/ath9k/hw.c +++ b/drivers/net/wireless/ath/ath9k/hw.c @@ -842,7 +842,7 @@ static void ath9k_hw_init_mode_regs(struct ath_hw *ah) static void ath9k_hw_init_mode_gain_regs(struct ath_hw *ah) { - if (AR_SREV_9287_11(ah)) + if (AR_SREV_9287_11_OR_LATER(ah)) INIT_INI_ARRAY(&ah->iniModesRxGain, ar9287Modes_rx_gain_9287_1_1, ARRAY_SIZE(ar9287Modes_rx_gain_9287_1_1), 6); @@ -853,7 +853,7 @@ static void ath9k_hw_init_mode_gain_regs(struct ath_hw *ah) else if (AR_SREV_9280_20(ah)) ath9k_hw_init_rxgain_ini(ah); - if (AR_SREV_9287_11(ah)) { + if (AR_SREV_9287_11_OR_LATER(ah)) { INIT_INI_ARRAY(&ah->iniModesTxGain, ar9287Modes_tx_gain_9287_1_1, ARRAY_SIZE(ar9287Modes_tx_gain_9287_1_1), 6); @@ -965,7 +965,7 @@ int ath9k_hw_init(struct ath_hw *ah) ath9k_hw_init_mode_regs(ah); if (ah->is_pciexpress) - ath9k_hw_configpcipowersave(ah, 0); + ath9k_hw_configpcipowersave(ah, 0, 0); else ath9k_hw_disablepcie(ah); @@ -1273,6 +1273,15 @@ static void ath9k_hw_override_ini(struct ath_hw *ah, */ REG_SET_BIT(ah, AR_DIAG_SW, (AR_DIAG_RX_DIS | AR_DIAG_RX_ABORT)); + if (AR_SREV_9280_10_OR_LATER(ah)) { + val = REG_READ(ah, AR_PCU_MISC_MODE2) & + (~AR_PCU_MISC_MODE2_HWWAR1); + + if (AR_SREV_9287_10_OR_LATER(ah)) + val = val & (~AR_PCU_MISC_MODE2_HWWAR2); + + REG_WRITE(ah, AR_PCU_MISC_MODE2, val); + } if (!AR_SREV_5416_20_OR_LATER(ah) || AR_SREV_9280_10_OR_LATER(ah)) @@ -1784,7 +1793,7 @@ static void ath9k_hw_set_regs(struct ath_hw *ah, struct ath9k_channel *chan, static bool ath9k_hw_chip_reset(struct ath_hw *ah, struct ath9k_channel *chan) { - if (OLC_FOR_AR9280_20_LATER) { + if (AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL)) { if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_POWER_ON)) return false; } else if (!ath9k_hw_set_reset_reg(ah, ATH9K_RESET_WARM)) @@ -2338,6 +2347,7 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, struct ath9k_channel *curchan = ah->curchan; u32 saveDefAntenna; u32 macStaId1; + u64 tsf = 0; int i, rx_chainmask, r; ah->extprotspacing = sc->ht_extprotspacing; @@ -2347,7 +2357,7 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, if (!ath9k_hw_setpower(ah, ATH9K_PM_AWAKE)) return -EIO; - if (curchan) + if (curchan && !ah->chip_fullsleep) ath9k_hw_getnf(ah, curchan); if (bChannelChange && @@ -2356,8 +2366,8 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, (chan->channel != ah->curchan->channel) && ((chan->channelFlags & CHANNEL_ALL) == (ah->curchan->channelFlags & CHANNEL_ALL)) && - (!AR_SREV_9280(ah) || (!IS_CHAN_A_5MHZ_SPACED(chan) && - !IS_CHAN_A_5MHZ_SPACED(ah->curchan)))) { + !(AR_SREV_9280(ah) || IS_CHAN_A_5MHZ_SPACED(chan) || + IS_CHAN_A_5MHZ_SPACED(ah->curchan))) { if (ath9k_hw_channel_change(ah, chan, sc->tx_chan_width)) { ath9k_hw_loadnf(ah, ah->curchan); @@ -2372,6 +2382,10 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, macStaId1 = REG_READ(ah, AR_STA_ID1) & AR_STA_ID1_BASE_RATE_11B; + /* For chips on which RTC reset is done, save TSF before it gets cleared */ + if (AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL)) + tsf = ath9k_hw_gettsf64(ah); + saveLedState = REG_READ(ah, AR_CFG_LED) & (AR_CFG_LED_ASSOC_CTL | AR_CFG_LED_MODE_SEL | AR_CFG_LED_BLINK_THRESH_SEL | AR_CFG_LED_BLINK_SLOW); @@ -2398,6 +2412,10 @@ int ath9k_hw_reset(struct ath_hw *ah, struct ath9k_channel *chan, udelay(50); } + /* Restore TSF */ + if (tsf && AR_SREV_9280(ah) && ah->eep_ops->get_eeprom(ah, EEP_OL_PWRCTRL)) + ath9k_hw_settsf64(ah, tsf); + if (AR_SREV_9280_10_OR_LATER(ah)) REG_SET_BIT(ah, AR_GPIO_INPUT_EN_VAL, AR_GPIO_JTAG_DISABLE); @@ -3005,9 +3023,10 @@ void ath9k_ps_restore(struct ath_softc *sc) * Programming the SerDes must go through the same 288 bit serial shift * register as the other analog registers. Hence the 9 writes. */ -void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore) +void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore, int power_off) { u8 i; + u32 val; if (ah->is_pciexpress != true) return; @@ -3017,84 +3036,113 @@ void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore) return; /* Nothing to do on restore for 11N */ - if (restore) - return; + if (!restore) { + if (AR_SREV_9280_20_OR_LATER(ah)) { + /* + * AR9280 2.0 or later chips use SerDes values from the + * initvals.h initialized depending on chipset during + * ath9k_hw_init() + */ + for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) { + REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0), + INI_RA(&ah->iniPcieSerdes, i, 1)); + } + } else if (AR_SREV_9280(ah) && + (ah->hw_version.macRev == AR_SREV_REVISION_9280_10)) { + REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00); + REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924); + + /* RX shut off when elecidle is asserted */ + REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019); + REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820); + REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560); + + /* Shut off CLKREQ active in L1 */ + if (ah->config.pcie_clock_req) + REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc); + else + REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffd); - if (AR_SREV_9280_20_OR_LATER(ah)) { - /* - * AR9280 2.0 or later chips use SerDes values from the - * initvals.h initialized depending on chipset during - * ath9k_hw_init() - */ - for (i = 0; i < ah->iniPcieSerdes.ia_rows; i++) { - REG_WRITE(ah, INI_RA(&ah->iniPcieSerdes, i, 0), - INI_RA(&ah->iniPcieSerdes, i, 1)); - } - } else if (AR_SREV_9280(ah) && - (ah->hw_version.macRev == AR_SREV_REVISION_9280_10)) { - REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fd00); - REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924); + REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40); + REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554); + REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007); - /* RX shut off when elecidle is asserted */ - REG_WRITE(ah, AR_PCIE_SERDES, 0xa8000019); - REG_WRITE(ah, AR_PCIE_SERDES, 0x13160820); - REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980560); + /* Load the new settings */ + REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000); - /* Shut off CLKREQ active in L1 */ - if (ah->config.pcie_clock_req) - REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffc); - else - REG_WRITE(ah, AR_PCIE_SERDES, 0x401deffd); - - REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40); - REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554); - REG_WRITE(ah, AR_PCIE_SERDES, 0x00043007); + } else { + REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00); + REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924); - /* Load the new settings */ - REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000); + /* RX shut off when elecidle is asserted */ + REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039); + REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824); + REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579); - } else { - REG_WRITE(ah, AR_PCIE_SERDES, 0x9248fc00); - REG_WRITE(ah, AR_PCIE_SERDES, 0x24924924); + /* + * Ignore ah->ah_config.pcie_clock_req setting for + * pre-AR9280 11n + */ + REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff); - /* RX shut off when elecidle is asserted */ - REG_WRITE(ah, AR_PCIE_SERDES, 0x28000039); - REG_WRITE(ah, AR_PCIE_SERDES, 0x53160824); - REG_WRITE(ah, AR_PCIE_SERDES, 0xe5980579); + REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40); + REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554); + REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007); - /* - * Ignore ah->ah_config.pcie_clock_req setting for - * pre-AR9280 11n - */ - REG_WRITE(ah, AR_PCIE_SERDES, 0x001defff); + /* Load the new settings */ + REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000); + } - REG_WRITE(ah, AR_PCIE_SERDES, 0x1aaabe40); - REG_WRITE(ah, AR_PCIE_SERDES, 0xbe105554); - REG_WRITE(ah, AR_PCIE_SERDES, 0x000e3007); + udelay(1000); - /* Load the new settings */ - REG_WRITE(ah, AR_PCIE_SERDES2, 0x00000000); - } + /* set bit 19 to allow forcing of pcie core into L1 state */ + REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA); - udelay(1000); + /* Several PCIe massages to ensure proper behaviour */ + if (ah->config.pcie_waen) { + val = ah->config.pcie_waen; + if (!power_off) + val &= (~AR_WA_D3_L1_DISABLE); + } else { + if (AR_SREV_9285(ah) || AR_SREV_9271(ah) || + AR_SREV_9287(ah)) { + val = AR9285_WA_DEFAULT; + if (!power_off) + val &= (~AR_WA_D3_L1_DISABLE); + } else if (AR_SREV_9280(ah)) { + /* + * On AR9280 chips bit 22 of 0x4004 needs to be + * set otherwise card may disappear. + */ + val = AR9280_WA_DEFAULT; + if (!power_off) + val &= (~AR_WA_D3_L1_DISABLE); + } else + val = AR_WA_DEFAULT; + } - /* set bit 19 to allow forcing of pcie core into L1 state */ - REG_SET_BIT(ah, AR_PCIE_PM_CTRL, AR_PCIE_PM_CTRL_ENA); + REG_WRITE(ah, AR_WA, val); + } - /* Several PCIe massages to ensure proper behaviour */ - if (ah->config.pcie_waen) { - REG_WRITE(ah, AR_WA, ah->config.pcie_waen); - } else { - if (AR_SREV_9285(ah) || AR_SREV_9271(ah) || AR_SREV_9287(ah)) - REG_WRITE(ah, AR_WA, AR9285_WA_DEFAULT); + if (power_off) { /* - * On AR9280 chips bit 22 of 0x4004 needs to be set to - * otherwise card may disappear. + * Set PCIe workaround bits + * bit 14 in WA register (disable L1) should only + * be set when device enters D3 and be cleared + * when device comes back to D0. */ - else if (AR_SREV_9280(ah)) - REG_WRITE(ah, AR_WA, AR9280_WA_DEFAULT); - else - REG_WRITE(ah, AR_WA, AR_WA_DEFAULT); + if (ah->config.pcie_waen) { + if (ah->config.pcie_waen & AR_WA_D3_L1_DISABLE) + REG_SET_BIT(ah, AR_WA, AR_WA_D3_L1_DISABLE); + } else { + if (((AR_SREV_9285(ah) || AR_SREV_9271(ah) || + AR_SREV_9287(ah)) && + (AR9285_WA_DEFAULT & AR_WA_D3_L1_DISABLE)) || + (AR_SREV_9280(ah) && + (AR9280_WA_DEFAULT & AR_WA_D3_L1_DISABLE))) { + REG_SET_BIT(ah, AR_WA, AR_WA_D3_L1_DISABLE); + } + } } } @@ -3652,15 +3700,7 @@ void ath9k_hw_fill_cap_info(struct ath_hw *ah) } #endif - if ((ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCI) || - (ah->hw_version.macVersion == AR_SREV_VERSION_5416_PCIE) || - (ah->hw_version.macVersion == AR_SREV_VERSION_9160) || - (ah->hw_version.macVersion == AR_SREV_VERSION_9100) || - (ah->hw_version.macVersion == AR_SREV_VERSION_9280) || - (ah->hw_version.macVersion == AR_SREV_VERSION_9285)) - pCap->hw_caps &= ~ATH9K_HW_CAP_AUTOSLEEP; - else - pCap->hw_caps |= ATH9K_HW_CAP_AUTOSLEEP; + pCap->hw_caps &= ~ATH9K_HW_CAP_AUTOSLEEP; if (AR_SREV_9280(ah) || AR_SREV_9285(ah)) pCap->hw_caps &= ~ATH9K_HW_CAP_4KB_SPLITTRANS; diff --git a/drivers/net/wireless/ath/ath9k/hw.h b/drivers/net/wireless/ath/ath9k/hw.h index 9106a0b537d..b8923457182 100644 --- a/drivers/net/wireless/ath/ath9k/hw.h +++ b/drivers/net/wireless/ath/ath9k/hw.h @@ -106,7 +106,7 @@ #define AH_TSF_WRITE_TIMEOUT 100 /* (us) */ #define AH_TIME_QUANTUM 10 #define AR_KEYTABLE_SIZE 128 -#define POWER_UP_TIME 200000 +#define POWER_UP_TIME 10000 #define SPUR_RSSI_THRESH 40 #define CAB_TIMEOUT_VAL 10 @@ -650,7 +650,7 @@ void ath9k_hw_set_sta_beacon_timers(struct ath_hw *ah, const struct ath9k_beacon_state *bs); bool ath9k_hw_setpower(struct ath_hw *ah, enum ath9k_power_mode mode); -void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore); +void ath9k_hw_configpcipowersave(struct ath_hw *ah, int restore, int power_off); /* Interrupt Handling */ bool ath9k_hw_intrpend(struct ath_hw *ah); diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 3dc7b5a13e6..52bed89063d 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -1131,7 +1131,7 @@ void ath_radio_enable(struct ath_softc *sc) int r; ath9k_ps_wakeup(sc); - ath9k_hw_configpcipowersave(ah, 0); + ath9k_hw_configpcipowersave(ah, 0, 0); if (!ah->curchan) ah->curchan = ath_get_curchannel(sc, sc->hw); @@ -1202,7 +1202,7 @@ void ath_radio_disable(struct ath_softc *sc) spin_unlock_bh(&sc->sc_resetlock); ath9k_hw_phy_disable(ah); - ath9k_hw_configpcipowersave(ah, 1); + ath9k_hw_configpcipowersave(ah, 1, 1); ath9k_ps_restore(sc); ath9k_hw_setpower(ah, ATH9K_PM_FULL_SLEEP); } @@ -1226,11 +1226,6 @@ static void ath9k_rfkill_poll_state(struct ieee80211_hw *hw) bool blocked = !!ath_is_rfkill_set(sc); wiphy_rfkill_set_hw_state(hw->wiphy, blocked); - - if (blocked) - ath_radio_disable(sc); - else - ath_radio_enable(sc); } static void ath_start_rfkill_poll(struct ath_softc *sc) @@ -1260,6 +1255,7 @@ void ath_detach(struct ath_softc *sc) DPRINTF(sc, ATH_DBG_CONFIG, "Detach ATH hw\n"); ath_deinit_leds(sc); + wiphy_rfkill_stop_polling(sc->hw->wiphy); for (i = 0; i < sc->num_sec_wiphy; i++) { struct ath_wiphy *aphy = sc->sec_wiphy[i]; @@ -1942,7 +1938,7 @@ static int ath9k_start(struct ieee80211_hw *hw) init_channel = ath_get_curchannel(sc, hw); /* Reset SERDES registers */ - ath9k_hw_configpcipowersave(sc->sc_ah, 0); + ath9k_hw_configpcipowersave(sc->sc_ah, 0, 0); /* * The basic interface to setting the hardware in a good @@ -2166,11 +2162,9 @@ static void ath9k_stop(struct ieee80211_hw *hw) } else sc->rx.rxlink = NULL; - wiphy_rfkill_stop_polling(sc->hw->wiphy); - /* disable HAL and put h/w to sleep */ ath9k_hw_disable(sc->sc_ah); - ath9k_hw_configpcipowersave(sc->sc_ah, 1); + ath9k_hw_configpcipowersave(sc->sc_ah, 1, 1); ath9k_hw_setpower(sc->sc_ah, ATH9K_PM_FULL_SLEEP); sc->sc_flags |= SC_OP_INVALID; diff --git a/drivers/net/wireless/ath/ath9k/reg.h b/drivers/net/wireless/ath/ath9k/reg.h index e5c29eb86e8..d83b77f821e 100644 --- a/drivers/net/wireless/ath/ath9k/reg.h +++ b/drivers/net/wireless/ath/ath9k/reg.h @@ -676,8 +676,9 @@ #define AR_RC_HOSTIF 0x00000100 #define AR_WA 0x4004 +#define AR_WA_D3_L1_DISABLE (1 << 14) #define AR9285_WA_DEFAULT 0x004a05cb -#define AR9280_WA_DEFAULT 0x0040073f +#define AR9280_WA_DEFAULT 0x0040073b #define AR_WA_DEFAULT 0x0000073f diff --git a/drivers/net/wireless/atmel.c b/drivers/net/wireless/atmel.c index a3b36b3a9d6..cce188837d1 100644 --- a/drivers/net/wireless/atmel.c +++ b/drivers/net/wireless/atmel.c @@ -3330,7 +3330,7 @@ static void atmel_smooth_qual(struct atmel_private *priv) priv->wstats.qual.updated &= ~IW_QUAL_QUAL_INVALID; } -/* deals with incoming managment frames. */ +/* deals with incoming management frames. */ static void atmel_management_frame(struct atmel_private *priv, struct ieee80211_hdr *header, u16 frame_len, u8 rssi) diff --git a/drivers/net/wireless/b43/Kconfig b/drivers/net/wireless/b43/Kconfig index 83e38134acc..54ea61c15d8 100644 --- a/drivers/net/wireless/b43/Kconfig +++ b/drivers/net/wireless/b43/Kconfig @@ -61,11 +61,28 @@ config B43_PCMCIA If unsure, say N. +config B43_SDIO + bool "Broadcom 43xx SDIO device support (EXPERIMENTAL)" + depends on B43 && SSB_SDIOHOST_POSSIBLE && EXPERIMENTAL + select SSB_SDIOHOST + ---help--- + Broadcom 43xx device support for Soft-MAC SDIO devices. + + With this config option you can drive Soft-MAC b43 cards with a + Secure Digital I/O interface. + This includes the WLAN daughter card found on the Nintendo Wii + video game console. + Note that this does not support Broadcom 43xx Full-MAC devices. + + It's safe to select Y here, even if you don't have a B43 SDIO device. + + If unsure, say N. + # Data transfers to the device via PIO -# This is only needed on PCMCIA devices. All others can do DMA properly. +# This is only needed on PCMCIA and SDIO devices. All others can do DMA properly. config B43_PIO bool - depends on B43 && (B43_PCMCIA || B43_FORCE_PIO) + depends on B43 && (B43_SDIO || B43_PCMCIA || B43_FORCE_PIO) select SSB_BLOCKIO default y diff --git a/drivers/net/wireless/b43/Makefile b/drivers/net/wireless/b43/Makefile index da379f4b0c3..84772a2542d 100644 --- a/drivers/net/wireless/b43/Makefile +++ b/drivers/net/wireless/b43/Makefile @@ -16,6 +16,7 @@ b43-$(CONFIG_B43_PIO) += pio.o b43-y += rfkill.o b43-$(CONFIG_B43_LEDS) += leds.o b43-$(CONFIG_B43_PCMCIA) += pcmcia.o +b43-$(CONFIG_B43_SDIO) += sdio.o b43-$(CONFIG_B43_DEBUG) += debugfs.o obj-$(CONFIG_B43) += b43.o diff --git a/drivers/net/wireless/b43/b43.h b/drivers/net/wireless/b43/b43.h index 09cfe68537b..fa1549a03c7 100644 --- a/drivers/net/wireless/b43/b43.h +++ b/drivers/net/wireless/b43/b43.h @@ -629,13 +629,6 @@ struct b43_wl { * from the mac80211 subsystem. */ u16 mac80211_initially_registered_queues; - /* R/W lock for data transmission. - * Transmissions on 2+ queues can run concurrently, but somebody else - * might sync with TX by write_lock_irqsave()'ing. */ - rwlock_t tx_lock; - /* Lock for LEDs access. */ - spinlock_t leds_lock; - /* We can only have one operating interface (802.11 core) * at a time. General information about this interface follows. */ @@ -686,6 +679,9 @@ struct b43_wl { struct work_struct tx_work; /* Queue of packets to be transmitted. */ struct sk_buff_head tx_queue; + + /* The device LEDs. */ + struct b43_leds leds; }; /* The type of the firmware file. */ @@ -768,13 +764,10 @@ struct b43_wldev { /* The device initialization status. * Use b43_status() to query. */ atomic_t __init_status; - /* Saved init status for handling suspend. */ - int suspend_init_status; bool bad_frames_preempt; /* Use "Bad Frames Preemption" (default off) */ bool dfq_valid; /* Directed frame queue valid (IBSS PS mode, ATIM) */ bool radio_hw_enable; /* saved state of radio hardware enabled state */ - bool suspend_in_progress; /* TRUE, if we are in a suspend/resume cycle */ bool qos_enabled; /* TRUE, if QoS is used. */ bool hwcrypto_enabled; /* TRUE, if HW crypto acceleration is enabled. */ @@ -794,12 +787,6 @@ struct b43_wldev { /* Various statistics about the physical device. */ struct b43_stats stats; - /* The device LEDs. */ - struct b43_led led_tx; - struct b43_led led_rx; - struct b43_led led_assoc; - struct b43_led led_radio; - /* Reason code of the last interrupt. */ u32 irq_reason; u32 dma_reason[6]; @@ -830,6 +817,10 @@ struct b43_wldev { /* Debugging stuff follows. */ #ifdef CONFIG_B43_DEBUG struct b43_dfsentry *dfsentry; + unsigned int irq_count; + unsigned int irq_bit_count[32]; + unsigned int tx_count; + unsigned int rx_count; #endif }; diff --git a/drivers/net/wireless/b43/debugfs.c b/drivers/net/wireless/b43/debugfs.c index 8f64943e3f6..80b19a44a40 100644 --- a/drivers/net/wireless/b43/debugfs.c +++ b/drivers/net/wireless/b43/debugfs.c @@ -689,6 +689,7 @@ static void b43_add_dynamic_debug(struct b43_wldev *dev) add_dyn_dbg("debug_lo", B43_DBG_LO, 0); add_dyn_dbg("debug_firmware", B43_DBG_FIRMWARE, 0); add_dyn_dbg("debug_keys", B43_DBG_KEYS, 0); + add_dyn_dbg("debug_verbose_stats", B43_DBG_VERBOSESTATS, 0); #undef add_dyn_dbg } diff --git a/drivers/net/wireless/b43/debugfs.h b/drivers/net/wireless/b43/debugfs.h index e47b4b488b0..822aad8842f 100644 --- a/drivers/net/wireless/b43/debugfs.h +++ b/drivers/net/wireless/b43/debugfs.h @@ -13,6 +13,7 @@ enum b43_dyndbg { /* Dynamic debugging features */ B43_DBG_LO, B43_DBG_FIRMWARE, B43_DBG_KEYS, + B43_DBG_VERBOSESTATS, __B43_NR_DYNDBG, }; diff --git a/drivers/net/wireless/b43/dma.c b/drivers/net/wireless/b43/dma.c index a467ee260a1..8701034569f 100644 --- a/drivers/net/wireless/b43/dma.c +++ b/drivers/net/wireless/b43/dma.c @@ -1428,9 +1428,9 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, ring->nr_failed_tx_packets++; ring->nr_total_packet_tries += status->frame_count; #endif /* DEBUG */ - ieee80211_tx_status_irqsafe(dev->wl->hw, meta->skb); + ieee80211_tx_status(dev->wl->hw, meta->skb); - /* skb is freed by ieee80211_tx_status_irqsafe() */ + /* skb is freed by ieee80211_tx_status() */ meta->skb = NULL; } else { /* No need to call free_descriptor_buffer here, as diff --git a/drivers/net/wireless/b43/leds.c b/drivers/net/wireless/b43/leds.c index c8b317094c3..fbe3d4f62ce 100644 --- a/drivers/net/wireless/b43/leds.c +++ b/drivers/net/wireless/b43/leds.c @@ -34,57 +34,88 @@ static void b43_led_turn_on(struct b43_wldev *dev, u8 led_index, bool activelow) { - struct b43_wl *wl = dev->wl; - unsigned long flags; u16 ctl; - spin_lock_irqsave(&wl->leds_lock, flags); ctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL); if (activelow) ctl &= ~(1 << led_index); else ctl |= (1 << led_index); b43_write16(dev, B43_MMIO_GPIO_CONTROL, ctl); - spin_unlock_irqrestore(&wl->leds_lock, flags); } static void b43_led_turn_off(struct b43_wldev *dev, u8 led_index, bool activelow) { - struct b43_wl *wl = dev->wl; - unsigned long flags; u16 ctl; - spin_lock_irqsave(&wl->leds_lock, flags); ctl = b43_read16(dev, B43_MMIO_GPIO_CONTROL); if (activelow) ctl |= (1 << led_index); else ctl &= ~(1 << led_index); b43_write16(dev, B43_MMIO_GPIO_CONTROL, ctl); - spin_unlock_irqrestore(&wl->leds_lock, flags); } -/* Callback from the LED subsystem. */ -static void b43_led_brightness_set(struct led_classdev *led_dev, - enum led_brightness brightness) +static void b43_led_update(struct b43_wldev *dev, + struct b43_led *led) { - struct b43_led *led = container_of(led_dev, struct b43_led, led_dev); - struct b43_wldev *dev = led->dev; bool radio_enabled; + bool turn_on; - if (unlikely(b43_status(dev) < B43_STAT_INITIALIZED)) + if (!led->wl) return; - /* Checking the radio-enabled status here is slightly racy, - * but we want to avoid the locking overhead and we don't care - * whether the LED has the wrong state for a second. */ radio_enabled = (dev->phy.radio_on && dev->radio_hw_enable); - if (brightness == LED_OFF || !radio_enabled) - b43_led_turn_off(dev, led->index, led->activelow); + /* The led->state read is racy, but we don't care. In case we raced + * with the brightness_set handler, we will be called again soon + * to fixup our state. */ + if (radio_enabled) + turn_on = atomic_read(&led->state) != LED_OFF; else + turn_on = 0; + if (turn_on == led->hw_state) + return; + led->hw_state = turn_on; + + if (turn_on) b43_led_turn_on(dev, led->index, led->activelow); + else + b43_led_turn_off(dev, led->index, led->activelow); +} + +static void b43_leds_work(struct work_struct *work) +{ + struct b43_leds *leds = container_of(work, struct b43_leds, work); + struct b43_wl *wl = container_of(leds, struct b43_wl, leds); + struct b43_wldev *dev; + + mutex_lock(&wl->mutex); + dev = wl->current_dev; + if (unlikely(!dev || b43_status(dev) < B43_STAT_STARTED)) + goto out_unlock; + + b43_led_update(dev, &wl->leds.led_tx); + b43_led_update(dev, &wl->leds.led_rx); + b43_led_update(dev, &wl->leds.led_radio); + b43_led_update(dev, &wl->leds.led_assoc); + +out_unlock: + mutex_unlock(&wl->mutex); +} + +/* Callback from the LED subsystem. */ +static void b43_led_brightness_set(struct led_classdev *led_dev, + enum led_brightness brightness) +{ + struct b43_led *led = container_of(led_dev, struct b43_led, led_dev); + struct b43_wl *wl = led->wl; + + if (likely(!wl->leds.stop)) { + atomic_set(&led->state, brightness); + ieee80211_queue_work(wl->hw, &wl->leds.work); + } } static int b43_register_led(struct b43_wldev *dev, struct b43_led *led, @@ -93,15 +124,15 @@ static int b43_register_led(struct b43_wldev *dev, struct b43_led *led, { int err; - b43_led_turn_off(dev, led_index, activelow); - if (led->dev) + if (led->wl) return -EEXIST; if (!default_trigger) return -EINVAL; - led->dev = dev; + led->wl = dev->wl; led->index = led_index; led->activelow = activelow; strncpy(led->name, name, sizeof(led->name)); + atomic_set(&led->state, 0); led->led_dev.name = led->name; led->led_dev.default_trigger = default_trigger; @@ -110,19 +141,19 @@ static int b43_register_led(struct b43_wldev *dev, struct b43_led *led, err = led_classdev_register(dev->dev->dev, &led->led_dev); if (err) { b43warn(dev->wl, "LEDs: Failed to register %s\n", name); - led->dev = NULL; + led->wl = NULL; return err; } + return 0; } static void b43_unregister_led(struct b43_led *led) { - if (!led->dev) + if (!led->wl) return; led_classdev_unregister(&led->led_dev); - b43_led_turn_off(led->dev, led->index, led->activelow); - led->dev = NULL; + led->wl = NULL; } static void b43_map_led(struct b43_wldev *dev, @@ -137,24 +168,20 @@ static void b43_map_led(struct b43_wldev *dev, * generic LED triggers. */ switch (behaviour) { case B43_LED_INACTIVE: - break; case B43_LED_OFF: - b43_led_turn_off(dev, led_index, activelow); - break; case B43_LED_ON: - b43_led_turn_on(dev, led_index, activelow); break; case B43_LED_ACTIVITY: case B43_LED_TRANSFER: case B43_LED_APTRANSFER: snprintf(name, sizeof(name), "b43-%s::tx", wiphy_name(hw->wiphy)); - b43_register_led(dev, &dev->led_tx, name, + b43_register_led(dev, &dev->wl->leds.led_tx, name, ieee80211_get_tx_led_name(hw), led_index, activelow); snprintf(name, sizeof(name), "b43-%s::rx", wiphy_name(hw->wiphy)); - b43_register_led(dev, &dev->led_rx, name, + b43_register_led(dev, &dev->wl->leds.led_rx, name, ieee80211_get_rx_led_name(hw), led_index, activelow); break; @@ -164,18 +191,15 @@ static void b43_map_led(struct b43_wldev *dev, case B43_LED_MODE_BG: snprintf(name, sizeof(name), "b43-%s::radio", wiphy_name(hw->wiphy)); - b43_register_led(dev, &dev->led_radio, name, + b43_register_led(dev, &dev->wl->leds.led_radio, name, ieee80211_get_radio_led_name(hw), led_index, activelow); - /* Sync the RF-kill LED state with radio and switch states. */ - if (dev->phy.radio_on && b43_is_hw_radio_enabled(dev)) - b43_led_turn_on(dev, led_index, activelow); break; case B43_LED_WEIRD: case B43_LED_ASSOC: snprintf(name, sizeof(name), "b43-%s::assoc", wiphy_name(hw->wiphy)); - b43_register_led(dev, &dev->led_assoc, name, + b43_register_led(dev, &dev->wl->leds.led_assoc, name, ieee80211_get_assoc_led_name(hw), led_index, activelow); break; @@ -186,58 +210,150 @@ static void b43_map_led(struct b43_wldev *dev, } } -void b43_leds_init(struct b43_wldev *dev) +static void b43_led_get_sprominfo(struct b43_wldev *dev, + unsigned int led_index, + enum b43_led_behaviour *behaviour, + bool *activelow) { struct ssb_bus *bus = dev->dev->bus; u8 sprom[4]; - int i; - enum b43_led_behaviour behaviour; - bool activelow; sprom[0] = bus->sprom.gpio0; sprom[1] = bus->sprom.gpio1; sprom[2] = bus->sprom.gpio2; sprom[3] = bus->sprom.gpio3; - for (i = 0; i < 4; i++) { - if (sprom[i] == 0xFF) { - /* There is no LED information in the SPROM - * for this LED. Hardcode it here. */ - activelow = 0; - switch (i) { - case 0: - behaviour = B43_LED_ACTIVITY; - activelow = 1; - if (bus->boardinfo.vendor == PCI_VENDOR_ID_COMPAQ) - behaviour = B43_LED_RADIO_ALL; - break; - case 1: - behaviour = B43_LED_RADIO_B; - if (bus->boardinfo.vendor == PCI_VENDOR_ID_ASUSTEK) - behaviour = B43_LED_ASSOC; - break; - case 2: - behaviour = B43_LED_RADIO_A; - break; - case 3: - behaviour = B43_LED_OFF; - break; - default: - B43_WARN_ON(1); - return; - } + if (sprom[led_index] == 0xFF) { + /* There is no LED information in the SPROM + * for this LED. Hardcode it here. */ + *activelow = 0; + switch (led_index) { + case 0: + *behaviour = B43_LED_ACTIVITY; + *activelow = 1; + if (bus->boardinfo.vendor == PCI_VENDOR_ID_COMPAQ) + *behaviour = B43_LED_RADIO_ALL; + break; + case 1: + *behaviour = B43_LED_RADIO_B; + if (bus->boardinfo.vendor == PCI_VENDOR_ID_ASUSTEK) + *behaviour = B43_LED_ASSOC; + break; + case 2: + *behaviour = B43_LED_RADIO_A; + break; + case 3: + *behaviour = B43_LED_OFF; + break; + default: + B43_WARN_ON(1); + return; + } + } else { + *behaviour = sprom[led_index] & B43_LED_BEHAVIOUR; + *activelow = !!(sprom[led_index] & B43_LED_ACTIVELOW); + } +} + +void b43_leds_init(struct b43_wldev *dev) +{ + struct b43_led *led; + unsigned int i; + enum b43_led_behaviour behaviour; + bool activelow; + + /* Sync the RF-kill LED state (if we have one) with radio and switch states. */ + led = &dev->wl->leds.led_radio; + if (led->wl) { + if (dev->phy.radio_on && b43_is_hw_radio_enabled(dev)) { + b43_led_turn_on(dev, led->index, led->activelow); + led->hw_state = 1; + atomic_set(&led->state, 1); } else { - behaviour = sprom[i] & B43_LED_BEHAVIOUR; - activelow = !!(sprom[i] & B43_LED_ACTIVELOW); + b43_led_turn_off(dev, led->index, led->activelow); + led->hw_state = 0; + atomic_set(&led->state, 0); } - b43_map_led(dev, i, behaviour, activelow); } + + /* Initialize TX/RX/ASSOC leds */ + led = &dev->wl->leds.led_tx; + if (led->wl) { + b43_led_turn_off(dev, led->index, led->activelow); + led->hw_state = 0; + atomic_set(&led->state, 0); + } + led = &dev->wl->leds.led_rx; + if (led->wl) { + b43_led_turn_off(dev, led->index, led->activelow); + led->hw_state = 0; + atomic_set(&led->state, 0); + } + led = &dev->wl->leds.led_assoc; + if (led->wl) { + b43_led_turn_off(dev, led->index, led->activelow); + led->hw_state = 0; + atomic_set(&led->state, 0); + } + + /* Initialize other LED states. */ + for (i = 0; i < B43_MAX_NR_LEDS; i++) { + b43_led_get_sprominfo(dev, i, &behaviour, &activelow); + switch (behaviour) { + case B43_LED_OFF: + b43_led_turn_off(dev, i, activelow); + break; + case B43_LED_ON: + b43_led_turn_on(dev, i, activelow); + break; + default: + /* Leave others as-is. */ + break; + } + } + + dev->wl->leds.stop = 0; } void b43_leds_exit(struct b43_wldev *dev) { - b43_unregister_led(&dev->led_tx); - b43_unregister_led(&dev->led_rx); - b43_unregister_led(&dev->led_assoc); - b43_unregister_led(&dev->led_radio); + struct b43_leds *leds = &dev->wl->leds; + + b43_led_turn_off(dev, leds->led_tx.index, leds->led_tx.activelow); + b43_led_turn_off(dev, leds->led_rx.index, leds->led_rx.activelow); + b43_led_turn_off(dev, leds->led_assoc.index, leds->led_assoc.activelow); + b43_led_turn_off(dev, leds->led_radio.index, leds->led_radio.activelow); +} + +void b43_leds_stop(struct b43_wldev *dev) +{ + struct b43_leds *leds = &dev->wl->leds; + + leds->stop = 1; + cancel_work_sync(&leds->work); +} + +void b43_leds_register(struct b43_wldev *dev) +{ + unsigned int i; + enum b43_led_behaviour behaviour; + bool activelow; + + INIT_WORK(&dev->wl->leds.work, b43_leds_work); + + /* Register the LEDs to the LED subsystem. */ + for (i = 0; i < B43_MAX_NR_LEDS; i++) { + b43_led_get_sprominfo(dev, i, &behaviour, &activelow); + b43_map_led(dev, i, behaviour, activelow); + } +} + +void b43_leds_unregister(struct b43_wldev *dev) +{ + struct b43_leds *leds = &dev->wl->leds; + + b43_unregister_led(&leds->led_tx); + b43_unregister_led(&leds->led_rx); + b43_unregister_led(&leds->led_assoc); + b43_unregister_led(&leds->led_radio); } diff --git a/drivers/net/wireless/b43/leds.h b/drivers/net/wireless/b43/leds.h index b8b1dd52124..9592e4c5a5f 100644 --- a/drivers/net/wireless/b43/leds.h +++ b/drivers/net/wireless/b43/leds.h @@ -7,12 +7,13 @@ struct b43_wldev; #include <linux/types.h> #include <linux/leds.h> +#include <linux/workqueue.h> #define B43_LED_MAX_NAME_LEN 31 struct b43_led { - struct b43_wldev *dev; + struct b43_wl *wl; /* The LED class device */ struct led_classdev led_dev; /* The index number of the LED. */ @@ -22,8 +23,24 @@ struct b43_led { bool activelow; /* The unique name string for this LED device. */ char name[B43_LED_MAX_NAME_LEN + 1]; + /* The current status of the LED. This is updated locklessly. */ + atomic_t state; + /* The active state in hardware. */ + bool hw_state; }; +struct b43_leds { + struct b43_led led_tx; + struct b43_led led_rx; + struct b43_led led_radio; + struct b43_led led_assoc; + + bool stop; + struct work_struct work; +}; + +#define B43_MAX_NR_LEDS 4 + #define B43_LED_BEHAVIOUR 0x7F #define B43_LED_ACTIVELOW 0x80 /* LED behaviour values */ @@ -42,23 +59,35 @@ enum b43_led_behaviour { B43_LED_INACTIVE, }; +void b43_leds_register(struct b43_wldev *dev); +void b43_leds_unregister(struct b43_wldev *dev); void b43_leds_init(struct b43_wldev *dev); void b43_leds_exit(struct b43_wldev *dev); +void b43_leds_stop(struct b43_wldev *dev); #else /* CONFIG_B43_LEDS */ /* LED support disabled */ -struct b43_led { +struct b43_leds { /* empty */ }; +static inline void b43_leds_register(struct b43_wldev *dev) +{ +} +static inline void b43_leds_unregister(struct b43_wldev *dev) +{ +} static inline void b43_leds_init(struct b43_wldev *dev) { } static inline void b43_leds_exit(struct b43_wldev *dev) { } +static inline void b43_leds_stop(struct b43_wldev *dev) +{ +} #endif /* CONFIG_B43_LEDS */ #endif /* B43_LEDS_H_ */ diff --git a/drivers/net/wireless/b43/main.c b/drivers/net/wireless/b43/main.c index 7a9a3fa5542..9b907a36bb8 100644 --- a/drivers/net/wireless/b43/main.c +++ b/drivers/net/wireless/b43/main.c @@ -8,6 +8,9 @@ Copyright (c) 2005 Danny van Dyk <kugelfang@gentoo.org> Copyright (c) 2005 Andreas Jaggi <andreas.jaggi@waterwave.ch> + SDIO support + Copyright (c) 2009 Albert Herranz <albert_herranz@yahoo.es> + Some parts of the code in this file are derived from the ipw2200 driver Copyright(c) 2003 - 2004 Intel Corporation. @@ -53,6 +56,8 @@ #include "xmit.h" #include "lo.h" #include "pcmcia.h" +#include "sdio.h" +#include <linux/mmc/sdio_func.h> MODULE_DESCRIPTION("Broadcom B43 wireless driver"); MODULE_AUTHOR("Martin Langer"); @@ -1587,7 +1592,7 @@ static void b43_beacon_update_trigger_work(struct work_struct *work) mutex_lock(&wl->mutex); dev = wl->current_dev; if (likely(dev && (b43_status(dev) >= B43_STAT_INITIALIZED))) { - if (0 /*FIXME dev->dev->bus->bustype == SSB_BUSTYPE_SDIO*/) { + if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) { /* wl->mutex is enough. */ b43_do_beacon_update_trigger_work(dev); mmiowb(); @@ -1825,6 +1830,16 @@ static void b43_do_interrupt_thread(struct b43_wldev *dev) /* Re-enable interrupts on the device by restoring the current interrupt mask. */ b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, dev->irq_mask); + +#if B43_DEBUG + if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { + dev->irq_count++; + for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { + if (reason & (1 << i)) + dev->irq_bit_count[i]++; + } + } +#endif } /* Interrupt thread handler. Handles device interrupts in thread context. */ @@ -1905,6 +1920,21 @@ static irqreturn_t b43_interrupt_handler(int irq, void *dev_id) return ret; } +/* SDIO interrupt handler. This runs in process context. */ +static void b43_sdio_interrupt_handler(struct b43_wldev *dev) +{ + struct b43_wl *wl = dev->wl; + irqreturn_t ret; + + mutex_lock(&wl->mutex); + + ret = b43_do_interrupt(dev); + if (ret == IRQ_WAKE_THREAD) + b43_do_interrupt_thread(dev); + + mutex_unlock(&wl->mutex); +} + void b43_do_release_fw(struct b43_firmware_file *fw) { release_firmware(fw->data); @@ -2289,11 +2319,7 @@ static int b43_upload_microcode(struct b43_wldev *dev) err = -ENODEV; goto error; } - msleep_interruptible(50); - if (signal_pending(current)) { - err = -EINTR; - goto error; - } + msleep(50); } b43_read32(dev, B43_MMIO_GEN_IRQ_REASON); /* dummy read */ @@ -2649,6 +2675,20 @@ static void b43_adjust_opmode(struct b43_wldev *dev) cfp_pretbtt = 50; } b43_write16(dev, 0x612, cfp_pretbtt); + + /* FIXME: We don't currently implement the PMQ mechanism, + * so always disable it. If we want to implement PMQ, + * we need to enable it here (clear DISCPMQ) in AP mode. + */ + if (0 /* ctl & B43_MACCTL_AP */) { + b43_write32(dev, B43_MMIO_MACCTL, + b43_read32(dev, B43_MMIO_MACCTL) + & ~B43_MACCTL_DISCPMQ); + } else { + b43_write32(dev, B43_MMIO_MACCTL, + b43_read32(dev, B43_MMIO_MACCTL) + | B43_MACCTL_DISCPMQ); + } } static void b43_rate_memory_write(struct b43_wldev *dev, u16 rate, int is_ofdm) @@ -2877,6 +2917,27 @@ static void b43_periodic_every15sec(struct b43_wldev *dev) atomic_set(&phy->txerr_cnt, B43_PHY_TX_BADNESS_LIMIT); wmb(); + +#if B43_DEBUG + if (b43_debug(dev, B43_DBG_VERBOSESTATS)) { + unsigned int i; + + b43dbg(dev->wl, "Stats: %7u IRQs/sec, %7u TX/sec, %7u RX/sec\n", + dev->irq_count / 15, + dev->tx_count / 15, + dev->rx_count / 15); + dev->irq_count = 0; + dev->tx_count = 0; + dev->rx_count = 0; + for (i = 0; i < ARRAY_SIZE(dev->irq_bit_count); i++) { + if (dev->irq_bit_count[i]) { + b43dbg(dev->wl, "Stats: %7u IRQ-%02u/sec (0x%08X)\n", + dev->irq_bit_count[i] / 15, i, (1 << i)); + dev->irq_bit_count[i] = 0; + } + } + } +#endif } static void do_periodic_work(struct b43_wldev *dev) @@ -3006,14 +3067,18 @@ static void b43_security_init(struct b43_wldev *dev) static int b43_rng_read(struct hwrng *rng, u32 *data) { struct b43_wl *wl = (struct b43_wl *)rng->priv; + struct b43_wldev *dev; + int count = -ENODEV; - /* FIXME: We need to take wl->mutex here to make sure the device - * is not going away from under our ass. However it could deadlock - * with hwrng internal locking. */ - - *data = b43_read16(wl->current_dev, B43_MMIO_RNG); + mutex_lock(&wl->mutex); + dev = wl->current_dev; + if (likely(dev && b43_status(dev) >= B43_STAT_INITIALIZED)) { + *data = b43_read16(dev, B43_MMIO_RNG); + count = sizeof(u16); + } + mutex_unlock(&wl->mutex); - return (sizeof(u16)); + return count; } #endif /* CONFIG_B43_HWRNG */ @@ -3072,6 +3137,9 @@ static void b43_tx_work(struct work_struct *work) dev_kfree_skb(skb); /* Drop it */ } +#if B43_DEBUG + dev->tx_count++; +#endif mutex_unlock(&wl->mutex); } @@ -3824,7 +3892,7 @@ redo: /* Disable interrupts on the device. */ b43_set_status(dev, B43_STAT_INITIALIZED); - if (0 /*FIXME dev->dev->bus->bustype == SSB_BUSTYPE_SDIO*/) { + if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) { /* wl->mutex is locked. That is enough. */ b43_write32(dev, B43_MMIO_GEN_IRQ_MASK, 0); b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ @@ -3834,10 +3902,15 @@ redo: b43_read32(dev, B43_MMIO_GEN_IRQ_MASK); /* Flush */ spin_unlock_irq(&wl->hardirq_lock); } - /* Synchronize the interrupt handlers. Unlock to avoid deadlocks. */ + /* Synchronize and free the interrupt handlers. Unlock to avoid deadlocks. */ orig_dev = dev; mutex_unlock(&wl->mutex); - synchronize_irq(dev->dev->irq); + if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) { + b43_sdio_free_irq(dev); + } else { + synchronize_irq(dev->dev->irq); + free_irq(dev->dev->irq, dev); + } mutex_lock(&wl->mutex); dev = wl->current_dev; if (!dev) @@ -3854,7 +3927,7 @@ redo: dev_kfree_skb(skb_dequeue(&wl->tx_queue)); b43_mac_suspend(dev); - free_irq(dev->dev->irq, dev); + b43_leds_exit(dev); b43dbg(wl, "Wireless interface stopped\n"); return dev; @@ -3868,12 +3941,20 @@ static int b43_wireless_core_start(struct b43_wldev *dev) B43_WARN_ON(b43_status(dev) != B43_STAT_INITIALIZED); drain_txstatus_queue(dev); - err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler, - b43_interrupt_thread_handler, - IRQF_SHARED, KBUILD_MODNAME, dev); - if (err) { - b43err(dev->wl, "Cannot request IRQ-%d\n", dev->dev->irq); - goto out; + if (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) { + err = b43_sdio_request_irq(dev, b43_sdio_interrupt_handler); + if (err) { + b43err(dev->wl, "Cannot request SDIO IRQ\n"); + goto out; + } + } else { + err = request_threaded_irq(dev->dev->irq, b43_interrupt_handler, + b43_interrupt_thread_handler, + IRQF_SHARED, KBUILD_MODNAME, dev); + if (err) { + b43err(dev->wl, "Cannot request IRQ-%d\n", dev->dev->irq); + goto out; + } } /* We are ready to run. */ @@ -3886,8 +3967,10 @@ static int b43_wireless_core_start(struct b43_wldev *dev) /* Start maintainance work */ b43_periodic_tasks_setup(dev); + b43_leds_init(dev); + b43dbg(dev->wl, "Wireless interface started\n"); - out: +out: return err; } @@ -4164,10 +4247,6 @@ static void b43_wireless_core_exit(struct b43_wldev *dev) macctl |= B43_MACCTL_PSM_JMP0; b43_write32(dev, B43_MMIO_MACCTL, macctl); - if (!dev->suspend_in_progress) { - b43_leds_exit(dev); - b43_rng_exit(dev->wl); - } b43_dma_free(dev); b43_pio_free(dev); b43_chip_exit(dev); @@ -4184,7 +4263,6 @@ static void b43_wireless_core_exit(struct b43_wldev *dev) /* Initialize a wireless core */ static int b43_wireless_core_init(struct b43_wldev *dev) { - struct b43_wl *wl = dev->wl; struct ssb_bus *bus = dev->dev->bus; struct ssb_sprom *sprom = &bus->sprom; struct b43_phy *phy = &dev->phy; @@ -4268,7 +4346,9 @@ static int b43_wireless_core_init(struct b43_wldev *dev) /* Maximum Contention Window */ b43_shm_write16(dev, B43_SHM_SCRATCH, B43_SHM_SC_MAXCONT, 0x3FF); - if ((dev->dev->bus->bustype == SSB_BUSTYPE_PCMCIA) || B43_FORCE_PIO) { + if ((dev->dev->bus->bustype == SSB_BUSTYPE_PCMCIA) || + (dev->dev->bus->bustype == SSB_BUSTYPE_SDIO) || + B43_FORCE_PIO) { dev->__using_pio_transfers = 1; err = b43_pio_init(dev); } else { @@ -4284,13 +4364,13 @@ static int b43_wireless_core_init(struct b43_wldev *dev) ssb_bus_powerup(bus, !(sprom->boardflags_lo & B43_BFL_XTAL_NOSLOW)); b43_upload_card_macaddress(dev); b43_security_init(dev); - if (!dev->suspend_in_progress) - b43_rng_init(wl); + + ieee80211_wake_queues(dev->wl->hw); + + ieee80211_wake_queues(dev->wl->hw); b43_set_status(dev, B43_STAT_INITIALIZED); - if (!dev->suspend_in_progress) - b43_leds_init(dev); out: return err; @@ -4839,7 +4919,6 @@ static int b43_wireless_init(struct ssb_device *dev) /* Initialize struct b43_wl */ wl->hw = hw; - spin_lock_init(&wl->leds_lock); mutex_init(&wl->mutex); spin_lock_init(&wl->hardirq_lock); INIT_LIST_HEAD(&wl->devlist); @@ -4880,6 +4959,8 @@ static int b43_probe(struct ssb_device *dev, const struct ssb_device_id *id) err = ieee80211_register_hw(wl->hw); if (err) goto err_one_core_detach; + b43_leds_register(wl->current_dev); + b43_rng_init(wl); } out: @@ -4908,12 +4989,15 @@ static void b43_remove(struct ssb_device *dev) * might have modified it. Restoring is important, so the networking * stack can properly free resources. */ wl->hw->queues = wl->mac80211_initially_registered_queues; + b43_leds_stop(wldev); ieee80211_unregister_hw(wl->hw); } b43_one_core_detach(dev); if (list_empty(&wl->devlist)) { + b43_rng_exit(wl); + b43_leds_unregister(wldev); /* Last core on the chip unregistered. * We can destroy common struct b43_wl. */ @@ -4931,80 +5015,17 @@ void b43_controller_restart(struct b43_wldev *dev, const char *reason) ieee80211_queue_work(dev->wl->hw, &dev->restart_work); } -#ifdef CONFIG_PM - -static int b43_suspend(struct ssb_device *dev, pm_message_t state) -{ - struct b43_wldev *wldev = ssb_get_drvdata(dev); - struct b43_wl *wl = wldev->wl; - - b43dbg(wl, "Suspending...\n"); - - mutex_lock(&wl->mutex); - wldev->suspend_in_progress = true; - wldev->suspend_init_status = b43_status(wldev); - if (wldev->suspend_init_status >= B43_STAT_STARTED) - wldev = b43_wireless_core_stop(wldev); - if (wldev && wldev->suspend_init_status >= B43_STAT_INITIALIZED) - b43_wireless_core_exit(wldev); - mutex_unlock(&wl->mutex); - - b43dbg(wl, "Device suspended.\n"); - - return 0; -} - -static int b43_resume(struct ssb_device *dev) -{ - struct b43_wldev *wldev = ssb_get_drvdata(dev); - struct b43_wl *wl = wldev->wl; - int err = 0; - - b43dbg(wl, "Resuming...\n"); - - mutex_lock(&wl->mutex); - if (wldev->suspend_init_status >= B43_STAT_INITIALIZED) { - err = b43_wireless_core_init(wldev); - if (err) { - b43err(wl, "Resume failed at core init\n"); - goto out; - } - } - if (wldev->suspend_init_status >= B43_STAT_STARTED) { - err = b43_wireless_core_start(wldev); - if (err) { - b43_leds_exit(wldev); - b43_rng_exit(wldev->wl); - b43_wireless_core_exit(wldev); - b43err(wl, "Resume failed at core start\n"); - goto out; - } - } - b43dbg(wl, "Device resumed.\n"); - out: - wldev->suspend_in_progress = false; - mutex_unlock(&wl->mutex); - return err; -} - -#else /* CONFIG_PM */ -# define b43_suspend NULL -# define b43_resume NULL -#endif /* CONFIG_PM */ - static struct ssb_driver b43_ssb_driver = { .name = KBUILD_MODNAME, .id_table = b43_ssb_tbl, .probe = b43_probe, .remove = b43_remove, - .suspend = b43_suspend, - .resume = b43_resume, }; static void b43_print_driverinfo(void) { const char *feat_pci = "", *feat_pcmcia = "", *feat_nphy = "", - *feat_leds = ""; + *feat_leds = "", *feat_sdio = ""; #ifdef CONFIG_B43_PCI_AUTOSELECT feat_pci = "P"; @@ -5018,11 +5039,14 @@ static void b43_print_driverinfo(void) #ifdef CONFIG_B43_LEDS feat_leds = "L"; #endif +#ifdef CONFIG_B43_SDIO + feat_sdio = "S"; +#endif printk(KERN_INFO "Broadcom 43xx driver loaded " - "[ Features: %s%s%s%s, Firmware-ID: " + "[ Features: %s%s%s%s%s, Firmware-ID: " B43_SUPPORTED_FIRMWARE_ID " ]\n", feat_pci, feat_pcmcia, feat_nphy, - feat_leds); + feat_leds, feat_sdio); } static int __init b43_init(void) @@ -5033,13 +5057,18 @@ static int __init b43_init(void) err = b43_pcmcia_init(); if (err) goto err_dfs_exit; - err = ssb_driver_register(&b43_ssb_driver); + err = b43_sdio_init(); if (err) goto err_pcmcia_exit; + err = ssb_driver_register(&b43_ssb_driver); + if (err) + goto err_sdio_exit; b43_print_driverinfo(); return err; +err_sdio_exit: + b43_sdio_exit(); err_pcmcia_exit: b43_pcmcia_exit(); err_dfs_exit: @@ -5050,6 +5079,7 @@ err_dfs_exit: static void __exit b43_exit(void) { ssb_driver_unregister(&b43_ssb_driver); + b43_sdio_exit(); b43_pcmcia_exit(); b43_debugfs_exit(); } diff --git a/drivers/net/wireless/b43/phy_lp.c b/drivers/net/wireless/b43/phy_lp.c index 3e02d969f68..1e318d815a5 100644 --- a/drivers/net/wireless/b43/phy_lp.c +++ b/drivers/net/wireless/b43/phy_lp.c @@ -2228,6 +2228,16 @@ static enum b43_txpwr_result b43_lpphy_op_recalc_txpower(struct b43_wldev *dev, return B43_TXPWR_RES_DONE; } +void b43_lpphy_op_switch_analog(struct b43_wldev *dev, bool on) +{ + if (on) { + b43_phy_mask(dev, B43_LPPHY_AFE_CTL_OVR, 0xfff8); + } else { + b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVRVAL, 0x0007); + b43_phy_set(dev, B43_LPPHY_AFE_CTL_OVR, 0x0007); + } +} + const struct b43_phy_operations b43_phyops_lp = { .allocate = b43_lpphy_op_allocate, .free = b43_lpphy_op_free, @@ -2239,7 +2249,7 @@ const struct b43_phy_operations b43_phyops_lp = { .radio_read = b43_lpphy_op_radio_read, .radio_write = b43_lpphy_op_radio_write, .software_rfkill = b43_lpphy_op_software_rfkill, - .switch_analog = b43_phyop_switch_analog_generic, + .switch_analog = b43_lpphy_op_switch_analog, .switch_channel = b43_lpphy_op_switch_channel, .get_default_chan = b43_lpphy_op_get_default_chan, .set_rx_antenna = b43_lpphy_op_set_rx_antenna, diff --git a/drivers/net/wireless/b43/pio.c b/drivers/net/wireless/b43/pio.c index 3498b68385e..e96091b3149 100644 --- a/drivers/net/wireless/b43/pio.c +++ b/drivers/net/wireless/b43/pio.c @@ -574,7 +574,7 @@ void b43_pio_handle_txstatus(struct b43_wldev *dev, q->buffer_used -= total_len; q->free_packet_slots += 1; - ieee80211_tx_status_irqsafe(dev->wl->hw, pack->skb); + ieee80211_tx_status(dev->wl->hw, pack->skb); pack->skb = NULL; list_add(&pack->list, &q->packets_list); diff --git a/drivers/net/wireless/b43/rfkill.c b/drivers/net/wireless/b43/rfkill.c index 31e55999893..7a3218c5ba7 100644 --- a/drivers/net/wireless/b43/rfkill.c +++ b/drivers/net/wireless/b43/rfkill.c @@ -28,7 +28,7 @@ /* Returns TRUE, if the radio is enabled in hardware. */ bool b43_is_hw_radio_enabled(struct b43_wldev *dev) { - if (dev->phy.rev >= 3) { + if (dev->phy.rev >= 3 || dev->phy.type == B43_PHYTYPE_LP) { if (!(b43_read32(dev, B43_MMIO_RADIO_HWENABLED_HI) & B43_MMIO_RADIO_HWENABLED_HI_MASK)) return 1; diff --git a/drivers/net/wireless/b43/sdio.c b/drivers/net/wireless/b43/sdio.c new file mode 100644 index 00000000000..0d3ac64147a --- /dev/null +++ b/drivers/net/wireless/b43/sdio.c @@ -0,0 +1,202 @@ +/* + * Broadcom B43 wireless driver + * + * SDIO over Sonics Silicon Backplane bus glue for b43. + * + * Copyright (C) 2009 Albert Herranz + * Copyright (C) 2009 Michael Buesch <mb@bu3sch.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or (at + * your option) any later version. + */ + +#include <linux/kernel.h> +#include <linux/mmc/card.h> +#include <linux/mmc/sdio_func.h> +#include <linux/mmc/sdio_ids.h> +#include <linux/ssb/ssb.h> + +#include "sdio.h" +#include "b43.h" + + +#define HNBU_CHIPID 0x01 /* vendor & device id */ + +#define B43_SDIO_BLOCK_SIZE 64 /* rx fifo max size in bytes */ + + +static const struct b43_sdio_quirk { + u16 vendor; + u16 device; + unsigned int quirks; +} b43_sdio_quirks[] = { + { 0x14E4, 0x4318, SSB_QUIRK_SDIO_READ_AFTER_WRITE32, }, + { }, +}; + + +static unsigned int b43_sdio_get_quirks(u16 vendor, u16 device) +{ + const struct b43_sdio_quirk *q; + + for (q = b43_sdio_quirks; q->quirks; q++) { + if (vendor == q->vendor && device == q->device) + return q->quirks; + } + + return 0; +} + +static void b43_sdio_interrupt_dispatcher(struct sdio_func *func) +{ + struct b43_sdio *sdio = sdio_get_drvdata(func); + struct b43_wldev *dev = sdio->irq_handler_opaque; + + if (unlikely(b43_status(dev) < B43_STAT_STARTED)) + return; + + sdio_release_host(func); + sdio->irq_handler(dev); + sdio_claim_host(func); +} + +int b43_sdio_request_irq(struct b43_wldev *dev, + void (*handler)(struct b43_wldev *dev)) +{ + struct ssb_bus *bus = dev->dev->bus; + struct sdio_func *func = bus->host_sdio; + struct b43_sdio *sdio = sdio_get_drvdata(func); + int err; + + sdio->irq_handler_opaque = dev; + sdio->irq_handler = handler; + sdio_claim_host(func); + err = sdio_claim_irq(func, b43_sdio_interrupt_dispatcher); + sdio_release_host(func); + + return err; +} + +void b43_sdio_free_irq(struct b43_wldev *dev) +{ + struct ssb_bus *bus = dev->dev->bus; + struct sdio_func *func = bus->host_sdio; + struct b43_sdio *sdio = sdio_get_drvdata(func); + + sdio_claim_host(func); + sdio_release_irq(func); + sdio_release_host(func); + sdio->irq_handler_opaque = NULL; + sdio->irq_handler = NULL; +} + +static int b43_sdio_probe(struct sdio_func *func, + const struct sdio_device_id *id) +{ + struct b43_sdio *sdio; + struct sdio_func_tuple *tuple; + u16 vendor = 0, device = 0; + int error; + + /* Look for the card chip identifier. */ + tuple = func->tuples; + while (tuple) { + switch (tuple->code) { + case 0x80: + switch (tuple->data[0]) { + case HNBU_CHIPID: + if (tuple->size != 5) + break; + vendor = tuple->data[1] | (tuple->data[2]<<8); + device = tuple->data[3] | (tuple->data[4]<<8); + dev_info(&func->dev, "Chip ID %04x:%04x\n", + vendor, device); + break; + default: + break; + } + break; + default: + break; + } + tuple = tuple->next; + } + if (!vendor || !device) { + error = -ENODEV; + goto out; + } + + sdio_claim_host(func); + error = sdio_set_block_size(func, B43_SDIO_BLOCK_SIZE); + if (error) { + dev_err(&func->dev, "failed to set block size to %u bytes," + " error %d\n", B43_SDIO_BLOCK_SIZE, error); + goto err_release_host; + } + error = sdio_enable_func(func); + if (error) { + dev_err(&func->dev, "failed to enable func, error %d\n", error); + goto err_release_host; + } + sdio_release_host(func); + + sdio = kzalloc(sizeof(*sdio), GFP_KERNEL); + if (!sdio) { + error = -ENOMEM; + dev_err(&func->dev, "failed to allocate ssb bus\n"); + goto err_disable_func; + } + error = ssb_bus_sdiobus_register(&sdio->ssb, func, + b43_sdio_get_quirks(vendor, device)); + if (error) { + dev_err(&func->dev, "failed to register ssb sdio bus," + " error %d\n", error); + goto err_free_ssb; + } + sdio_set_drvdata(func, sdio); + + return 0; + +err_free_ssb: + kfree(sdio); +err_disable_func: + sdio_disable_func(func); +err_release_host: + sdio_release_host(func); +out: + return error; +} + +static void b43_sdio_remove(struct sdio_func *func) +{ + struct b43_sdio *sdio = sdio_get_drvdata(func); + + ssb_bus_unregister(&sdio->ssb); + sdio_disable_func(func); + kfree(sdio); + sdio_set_drvdata(func, NULL); +} + +static const struct sdio_device_id b43_sdio_ids[] = { + { SDIO_DEVICE(0x02d0, 0x044b) }, /* Nintendo Wii WLAN daughter card */ + { }, +}; + +static struct sdio_driver b43_sdio_driver = { + .name = "b43-sdio", + .id_table = b43_sdio_ids, + .probe = b43_sdio_probe, + .remove = b43_sdio_remove, +}; + +int b43_sdio_init(void) +{ + return sdio_register_driver(&b43_sdio_driver); +} + +void b43_sdio_exit(void) +{ + sdio_unregister_driver(&b43_sdio_driver); +} diff --git a/drivers/net/wireless/b43/sdio.h b/drivers/net/wireless/b43/sdio.h new file mode 100644 index 00000000000..fb633094403 --- /dev/null +++ b/drivers/net/wireless/b43/sdio.h @@ -0,0 +1,45 @@ +#ifndef B43_SDIO_H_ +#define B43_SDIO_H_ + +#include <linux/ssb/ssb.h> + +struct b43_wldev; + + +#ifdef CONFIG_B43_SDIO + +struct b43_sdio { + struct ssb_bus ssb; + void *irq_handler_opaque; + void (*irq_handler)(struct b43_wldev *dev); +}; + +int b43_sdio_request_irq(struct b43_wldev *dev, + void (*handler)(struct b43_wldev *dev)); +void b43_sdio_free_irq(struct b43_wldev *dev); + +int b43_sdio_init(void); +void b43_sdio_exit(void); + + +#else /* CONFIG_B43_SDIO */ + + +int b43_sdio_request_irq(struct b43_wldev *dev, + void (*handler)(struct b43_wldev *dev)) +{ + return -ENODEV; +} +void b43_sdio_free_irq(struct b43_wldev *dev) +{ +} +static inline int b43_sdio_init(void) +{ + return 0; +} +static inline void b43_sdio_exit(void) +{ +} + +#endif /* CONFIG_B43_SDIO */ +#endif /* B43_SDIO_H_ */ diff --git a/drivers/net/wireless/b43/xmit.c b/drivers/net/wireless/b43/xmit.c index 14f541248b5..ac9f600995e 100644 --- a/drivers/net/wireless/b43/xmit.c +++ b/drivers/net/wireless/b43/xmit.c @@ -690,8 +690,11 @@ void b43_rx(struct b43_wldev *dev, struct sk_buff *skb, const void *_rxhdr) } memcpy(IEEE80211_SKB_RXCB(skb), &status, sizeof(status)); - ieee80211_rx_irqsafe(dev->wl->hw, skb); + ieee80211_rx(dev->wl->hw, skb); +#if B43_DEBUG + dev->rx_count++; +#endif return; drop: b43dbg(dev->wl, "RX: Packet dropped\n"); diff --git a/drivers/net/wireless/hostap/hostap_main.c b/drivers/net/wireless/hostap/hostap_main.c index 6fe122f18c0..eb57d1ea361 100644 --- a/drivers/net/wireless/hostap/hostap_main.c +++ b/drivers/net/wireless/hostap/hostap_main.c @@ -875,15 +875,16 @@ void hostap_setup_dev(struct net_device *dev, local_info_t *local, switch(type) { case HOSTAP_INTERFACE_AP: + dev->tx_queue_len = 0; /* use main radio device queue */ dev->netdev_ops = &hostap_mgmt_netdev_ops; dev->type = ARPHRD_IEEE80211; dev->header_ops = &hostap_80211_ops; break; case HOSTAP_INTERFACE_MASTER: - dev->tx_queue_len = 0; /* use main radio device queue */ dev->netdev_ops = &hostap_master_ops; break; default: + dev->tx_queue_len = 0; /* use main radio device queue */ dev->netdev_ops = &hostap_netdev_ops; } diff --git a/drivers/net/wireless/iwlwifi/iwl-1000.c b/drivers/net/wireless/iwlwifi/iwl-1000.c index a95caa01414..2716b91ba9f 100644 --- a/drivers/net/wireless/iwlwifi/iwl-1000.c +++ b/drivers/net/wireless/iwlwifi/iwl-1000.c @@ -99,6 +99,8 @@ static struct iwl_lib_ops iwl1000_lib = { .setup_deferred_work = iwl5000_setup_deferred_work, .is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr, .load_ucode = iwl5000_load_ucode, + .dump_nic_event_log = iwl_dump_nic_event_log, + .dump_nic_error_log = iwl_dump_nic_error_log, .init_alive_start = iwl5000_init_alive_start, .alive_notify = iwl5000_alive_notify, .send_tx_power = iwl5000_send_tx_power, diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.c b/drivers/net/wireless/iwlwifi/iwl-3945.c index e9a685d8e3a..e70c5b0af36 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.c +++ b/drivers/net/wireless/iwlwifi/iwl-3945.c @@ -2839,6 +2839,8 @@ static struct iwl_lib_ops iwl3945_lib = { .txq_free_tfd = iwl3945_hw_txq_free_tfd, .txq_init = iwl3945_hw_tx_queue_init, .load_ucode = iwl3945_load_bsm, + .dump_nic_event_log = iwl3945_dump_nic_event_log, + .dump_nic_error_log = iwl3945_dump_nic_error_log, .apm_ops = { .init = iwl3945_apm_init, .reset = iwl3945_apm_reset, diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.h b/drivers/net/wireless/iwlwifi/iwl-3945.h index f2403690991..21679bf3a1a 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945.h @@ -209,6 +209,8 @@ extern int __must_check iwl3945_send_cmd(struct iwl_priv *priv, struct iwl_host_cmd *cmd); extern unsigned int iwl3945_fill_beacon_frame(struct iwl_priv *priv, struct ieee80211_hdr *hdr,int left); +extern void iwl3945_dump_nic_event_log(struct iwl_priv *priv); +extern void iwl3945_dump_nic_error_log(struct iwl_priv *priv); /* * Currently used by iwl-3945-rs... look at restructuring so that it doesn't diff --git a/drivers/net/wireless/iwlwifi/iwl-4965.c b/drivers/net/wireless/iwlwifi/iwl-4965.c index 6a13bfbc9d9..a22a0501c19 100644 --- a/drivers/net/wireless/iwlwifi/iwl-4965.c +++ b/drivers/net/wireless/iwlwifi/iwl-4965.c @@ -2021,6 +2021,12 @@ static int iwl4965_tx_status_reply_tx(struct iwl_priv *priv, agg->frame_count, txq_id, idx); hdr = iwl_tx_queue_get_hdr(priv, txq_id, idx); + if (!hdr) { + IWL_ERR(priv, + "BUG_ON idx doesn't point to valid skb" + " idx=%d, txq_id=%d\n", idx, txq_id); + return -1; + } sc = le16_to_cpu(hdr->seq_ctrl); if (idx != (SEQ_TO_SN(sc) & 0xff)) { @@ -2292,6 +2298,8 @@ static struct iwl_lib_ops iwl4965_lib = { .alive_notify = iwl4965_alive_notify, .init_alive_start = iwl4965_init_alive_start, .load_ucode = iwl4965_load_bsm, + .dump_nic_event_log = iwl_dump_nic_event_log, + .dump_nic_error_log = iwl_dump_nic_error_log, .apm_ops = { .init = iwl4965_apm_init, .reset = iwl4965_apm_reset, @@ -2346,6 +2354,7 @@ struct iwl_cfg iwl4965_agn_cfg = { .mod_params = &iwl4965_mod_params, .use_isr_legacy = true, .ht_greenfield_support = false, + .broken_powersave = true, }; /* Module firmware */ diff --git a/drivers/net/wireless/iwlwifi/iwl-5000.c b/drivers/net/wireless/iwlwifi/iwl-5000.c index 1d539e3b8db..eb08f441100 100644 --- a/drivers/net/wireless/iwlwifi/iwl-5000.c +++ b/drivers/net/wireless/iwlwifi/iwl-5000.c @@ -1163,6 +1163,12 @@ static int iwl5000_tx_status_reply_tx(struct iwl_priv *priv, agg->frame_count, txq_id, idx); hdr = iwl_tx_queue_get_hdr(priv, txq_id, idx); + if (!hdr) { + IWL_ERR(priv, + "BUG_ON idx doesn't point to valid skb" + " idx=%d, txq_id=%d\n", idx, txq_id); + return -1; + } sc = le16_to_cpu(hdr->seq_ctrl); if (idx != (SEQ_TO_SN(sc) & 0xff)) { @@ -1529,6 +1535,8 @@ struct iwl_lib_ops iwl5000_lib = { .rx_handler_setup = iwl5000_rx_handler_setup, .setup_deferred_work = iwl5000_setup_deferred_work, .is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr, + .dump_nic_event_log = iwl_dump_nic_event_log, + .dump_nic_error_log = iwl_dump_nic_error_log, .load_ucode = iwl5000_load_ucode, .init_alive_start = iwl5000_init_alive_start, .alive_notify = iwl5000_alive_notify, @@ -1579,6 +1587,8 @@ static struct iwl_lib_ops iwl5150_lib = { .rx_handler_setup = iwl5000_rx_handler_setup, .setup_deferred_work = iwl5000_setup_deferred_work, .is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr, + .dump_nic_event_log = iwl_dump_nic_event_log, + .dump_nic_error_log = iwl_dump_nic_error_log, .load_ucode = iwl5000_load_ucode, .init_alive_start = iwl5000_init_alive_start, .alive_notify = iwl5000_alive_notify, diff --git a/drivers/net/wireless/iwlwifi/iwl-6000.c b/drivers/net/wireless/iwlwifi/iwl-6000.c index 82b9c93dff5..c295b8ee922 100644 --- a/drivers/net/wireless/iwlwifi/iwl-6000.c +++ b/drivers/net/wireless/iwlwifi/iwl-6000.c @@ -100,6 +100,8 @@ static struct iwl_lib_ops iwl6000_lib = { .setup_deferred_work = iwl5000_setup_deferred_work, .is_valid_rtc_data_addr = iwl5000_hw_valid_rtc_data_addr, .load_ucode = iwl5000_load_ucode, + .dump_nic_event_log = iwl_dump_nic_event_log, + .dump_nic_error_log = iwl_dump_nic_error_log, .init_alive_start = iwl5000_init_alive_start, .alive_notify = iwl5000_alive_notify, .send_tx_power = iwl5000_send_tx_power, diff --git a/drivers/net/wireless/iwlwifi/iwl-agn-rs.c b/drivers/net/wireless/iwlwifi/iwl-agn-rs.c index 40b207aa8fe..346dc06fa7b 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn-rs.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn-rs.c @@ -760,6 +760,7 @@ static u32 rs_get_lower_rate(struct iwl_lq_sta *lq_sta, u16 high_low; u8 switch_to_legacy = 0; u8 is_green = lq_sta->is_green; + struct iwl_priv *priv = lq_sta->drv; /* check if we need to switch from HT to legacy rates. * assumption is that mandatory rates (1Mbps or 6Mbps) @@ -773,7 +774,8 @@ static u32 rs_get_lower_rate(struct iwl_lq_sta *lq_sta, tbl->lq_type = LQ_G; if (num_of_ant(tbl->ant_type) > 1) - tbl->ant_type = ANT_A;/*FIXME:RS*/ + tbl->ant_type = + first_antenna(priv->hw_params.valid_tx_ant); tbl->is_ht40 = 0; tbl->is_SGI = 0; @@ -883,6 +885,12 @@ static void rs_tx_status(void *priv_r, struct ieee80211_supported_band *sband, mac_index &= RATE_MCS_CODE_MSK; /* Remove # of streams */ if (mac_index >= (IWL_RATE_9M_INDEX - IWL_FIRST_OFDM_RATE)) mac_index++; + /* + * mac80211 HT index is always zero-indexed; we need to move + * HT OFDM rates after CCK rates in 2.4 GHz band + */ + if (priv->band == IEEE80211_BAND_2GHZ) + mac_index += IWL_FIRST_OFDM_RATE; } if ((mac_index < 0) || diff --git a/drivers/net/wireless/iwlwifi/iwl-agn.c b/drivers/net/wireless/iwlwifi/iwl-agn.c index 00457bff1ed..cdc07c47745 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn.c @@ -1526,6 +1526,191 @@ static int iwl_read_ucode(struct iwl_priv *priv) return ret; } +#ifdef CONFIG_IWLWIFI_DEBUG +static const char *desc_lookup_text[] = { + "OK", + "FAIL", + "BAD_PARAM", + "BAD_CHECKSUM", + "NMI_INTERRUPT_WDG", + "SYSASSERT", + "FATAL_ERROR", + "BAD_COMMAND", + "HW_ERROR_TUNE_LOCK", + "HW_ERROR_TEMPERATURE", + "ILLEGAL_CHAN_FREQ", + "VCC_NOT_STABLE", + "FH_ERROR", + "NMI_INTERRUPT_HOST", + "NMI_INTERRUPT_ACTION_PT", + "NMI_INTERRUPT_UNKNOWN", + "UCODE_VERSION_MISMATCH", + "HW_ERROR_ABS_LOCK", + "HW_ERROR_CAL_LOCK_FAIL", + "NMI_INTERRUPT_INST_ACTION_PT", + "NMI_INTERRUPT_DATA_ACTION_PT", + "NMI_TRM_HW_ER", + "NMI_INTERRUPT_TRM", + "NMI_INTERRUPT_BREAK_POINT" + "DEBUG_0", + "DEBUG_1", + "DEBUG_2", + "DEBUG_3", + "UNKNOWN" +}; + +static const char *desc_lookup(int i) +{ + int max = ARRAY_SIZE(desc_lookup_text) - 1; + + if (i < 0 || i > max) + i = max; + + return desc_lookup_text[i]; +} + +#define ERROR_START_OFFSET (1 * sizeof(u32)) +#define ERROR_ELEM_SIZE (7 * sizeof(u32)) + +void iwl_dump_nic_error_log(struct iwl_priv *priv) +{ + u32 data2, line; + u32 desc, time, count, base, data1; + u32 blink1, blink2, ilink1, ilink2; + + if (priv->ucode_type == UCODE_INIT) + base = le32_to_cpu(priv->card_alive_init.error_event_table_ptr); + else + base = le32_to_cpu(priv->card_alive.error_event_table_ptr); + + if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) { + IWL_ERR(priv, "Not valid error log pointer 0x%08X\n", base); + return; + } + + count = iwl_read_targ_mem(priv, base); + + if (ERROR_START_OFFSET <= count * ERROR_ELEM_SIZE) { + IWL_ERR(priv, "Start IWL Error Log Dump:\n"); + IWL_ERR(priv, "Status: 0x%08lX, count: %d\n", + priv->status, count); + } + + desc = iwl_read_targ_mem(priv, base + 1 * sizeof(u32)); + blink1 = iwl_read_targ_mem(priv, base + 3 * sizeof(u32)); + blink2 = iwl_read_targ_mem(priv, base + 4 * sizeof(u32)); + ilink1 = iwl_read_targ_mem(priv, base + 5 * sizeof(u32)); + ilink2 = iwl_read_targ_mem(priv, base + 6 * sizeof(u32)); + data1 = iwl_read_targ_mem(priv, base + 7 * sizeof(u32)); + data2 = iwl_read_targ_mem(priv, base + 8 * sizeof(u32)); + line = iwl_read_targ_mem(priv, base + 9 * sizeof(u32)); + time = iwl_read_targ_mem(priv, base + 11 * sizeof(u32)); + + IWL_ERR(priv, "Desc Time " + "data1 data2 line\n"); + IWL_ERR(priv, "%-28s (#%02d) %010u 0x%08X 0x%08X %u\n", + desc_lookup(desc), desc, time, data1, data2, line); + IWL_ERR(priv, "blink1 blink2 ilink1 ilink2\n"); + IWL_ERR(priv, "0x%05X 0x%05X 0x%05X 0x%05X\n", blink1, blink2, + ilink1, ilink2); + +} + +#define EVENT_START_OFFSET (4 * sizeof(u32)) + +/** + * iwl_print_event_log - Dump error event log to syslog + * + */ +static void iwl_print_event_log(struct iwl_priv *priv, u32 start_idx, + u32 num_events, u32 mode) +{ + u32 i; + u32 base; /* SRAM byte address of event log header */ + u32 event_size; /* 2 u32s, or 3 u32s if timestamp recorded */ + u32 ptr; /* SRAM byte address of log data */ + u32 ev, time, data; /* event log data */ + + if (num_events == 0) + return; + if (priv->ucode_type == UCODE_INIT) + base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr); + else + base = le32_to_cpu(priv->card_alive.log_event_table_ptr); + + if (mode == 0) + event_size = 2 * sizeof(u32); + else + event_size = 3 * sizeof(u32); + + ptr = base + EVENT_START_OFFSET + (start_idx * event_size); + + /* "time" is actually "data" for mode 0 (no timestamp). + * place event id # at far right for easier visual parsing. */ + for (i = 0; i < num_events; i++) { + ev = iwl_read_targ_mem(priv, ptr); + ptr += sizeof(u32); + time = iwl_read_targ_mem(priv, ptr); + ptr += sizeof(u32); + if (mode == 0) { + /* data, ev */ + IWL_ERR(priv, "EVT_LOG:0x%08x:%04u\n", time, ev); + } else { + data = iwl_read_targ_mem(priv, ptr); + ptr += sizeof(u32); + IWL_ERR(priv, "EVT_LOGT:%010u:0x%08x:%04u\n", + time, data, ev); + } + } +} + +void iwl_dump_nic_event_log(struct iwl_priv *priv) +{ + u32 base; /* SRAM byte address of event log header */ + u32 capacity; /* event log capacity in # entries */ + u32 mode; /* 0 - no timestamp, 1 - timestamp recorded */ + u32 num_wraps; /* # times uCode wrapped to top of log */ + u32 next_entry; /* index of next entry to be written by uCode */ + u32 size; /* # entries that we'll print */ + + if (priv->ucode_type == UCODE_INIT) + base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr); + else + base = le32_to_cpu(priv->card_alive.log_event_table_ptr); + + if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) { + IWL_ERR(priv, "Invalid event log pointer 0x%08X\n", base); + return; + } + + /* event log header */ + capacity = iwl_read_targ_mem(priv, base); + mode = iwl_read_targ_mem(priv, base + (1 * sizeof(u32))); + num_wraps = iwl_read_targ_mem(priv, base + (2 * sizeof(u32))); + next_entry = iwl_read_targ_mem(priv, base + (3 * sizeof(u32))); + + size = num_wraps ? capacity : next_entry; + + /* bail out if nothing in log */ + if (size == 0) { + IWL_ERR(priv, "Start IWL Event Log Dump: nothing in log\n"); + return; + } + + IWL_ERR(priv, "Start IWL Event Log Dump: display count %d, wraps %d\n", + size, num_wraps); + + /* if uCode has wrapped back to top of log, start at the oldest entry, + * i.e the next one that uCode would fill. */ + if (num_wraps) + iwl_print_event_log(priv, next_entry, + capacity - next_entry, mode); + /* (then/else) start at top of log */ + iwl_print_event_log(priv, 0, next_entry, mode); + +} +#endif + /** * iwl_alive_start - called after REPLY_ALIVE notification received * from protocol/runtime uCode (initialization uCode's diff --git a/drivers/net/wireless/iwlwifi/iwl-core.c b/drivers/net/wireless/iwlwifi/iwl-core.c index acfd7b40afb..484d5c1a731 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.c +++ b/drivers/net/wireless/iwlwifi/iwl-core.c @@ -1309,189 +1309,6 @@ static void iwl_print_rx_config_cmd(struct iwl_priv *priv) IWL_DEBUG_RADIO(priv, "u8[6] bssid_addr: %pM\n", rxon->bssid_addr); IWL_DEBUG_RADIO(priv, "u16 assoc_id: 0x%x\n", le16_to_cpu(rxon->assoc_id)); } - -static const char *desc_lookup_text[] = { - "OK", - "FAIL", - "BAD_PARAM", - "BAD_CHECKSUM", - "NMI_INTERRUPT_WDG", - "SYSASSERT", - "FATAL_ERROR", - "BAD_COMMAND", - "HW_ERROR_TUNE_LOCK", - "HW_ERROR_TEMPERATURE", - "ILLEGAL_CHAN_FREQ", - "VCC_NOT_STABLE", - "FH_ERROR", - "NMI_INTERRUPT_HOST", - "NMI_INTERRUPT_ACTION_PT", - "NMI_INTERRUPT_UNKNOWN", - "UCODE_VERSION_MISMATCH", - "HW_ERROR_ABS_LOCK", - "HW_ERROR_CAL_LOCK_FAIL", - "NMI_INTERRUPT_INST_ACTION_PT", - "NMI_INTERRUPT_DATA_ACTION_PT", - "NMI_TRM_HW_ER", - "NMI_INTERRUPT_TRM", - "NMI_INTERRUPT_BREAK_POINT" - "DEBUG_0", - "DEBUG_1", - "DEBUG_2", - "DEBUG_3", - "UNKNOWN" -}; - -static const char *desc_lookup(int i) -{ - int max = ARRAY_SIZE(desc_lookup_text) - 1; - - if (i < 0 || i > max) - i = max; - - return desc_lookup_text[i]; -} - -#define ERROR_START_OFFSET (1 * sizeof(u32)) -#define ERROR_ELEM_SIZE (7 * sizeof(u32)) - -static void iwl_dump_nic_error_log(struct iwl_priv *priv) -{ - u32 data2, line; - u32 desc, time, count, base, data1; - u32 blink1, blink2, ilink1, ilink2; - - if (priv->ucode_type == UCODE_INIT) - base = le32_to_cpu(priv->card_alive_init.error_event_table_ptr); - else - base = le32_to_cpu(priv->card_alive.error_event_table_ptr); - - if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) { - IWL_ERR(priv, "Not valid error log pointer 0x%08X\n", base); - return; - } - - count = iwl_read_targ_mem(priv, base); - - if (ERROR_START_OFFSET <= count * ERROR_ELEM_SIZE) { - IWL_ERR(priv, "Start IWL Error Log Dump:\n"); - IWL_ERR(priv, "Status: 0x%08lX, count: %d\n", - priv->status, count); - } - - desc = iwl_read_targ_mem(priv, base + 1 * sizeof(u32)); - blink1 = iwl_read_targ_mem(priv, base + 3 * sizeof(u32)); - blink2 = iwl_read_targ_mem(priv, base + 4 * sizeof(u32)); - ilink1 = iwl_read_targ_mem(priv, base + 5 * sizeof(u32)); - ilink2 = iwl_read_targ_mem(priv, base + 6 * sizeof(u32)); - data1 = iwl_read_targ_mem(priv, base + 7 * sizeof(u32)); - data2 = iwl_read_targ_mem(priv, base + 8 * sizeof(u32)); - line = iwl_read_targ_mem(priv, base + 9 * sizeof(u32)); - time = iwl_read_targ_mem(priv, base + 11 * sizeof(u32)); - - IWL_ERR(priv, "Desc Time " - "data1 data2 line\n"); - IWL_ERR(priv, "%-28s (#%02d) %010u 0x%08X 0x%08X %u\n", - desc_lookup(desc), desc, time, data1, data2, line); - IWL_ERR(priv, "blink1 blink2 ilink1 ilink2\n"); - IWL_ERR(priv, "0x%05X 0x%05X 0x%05X 0x%05X\n", blink1, blink2, - ilink1, ilink2); - -} - -#define EVENT_START_OFFSET (4 * sizeof(u32)) - -/** - * iwl_print_event_log - Dump error event log to syslog - * - */ -static void iwl_print_event_log(struct iwl_priv *priv, u32 start_idx, - u32 num_events, u32 mode) -{ - u32 i; - u32 base; /* SRAM byte address of event log header */ - u32 event_size; /* 2 u32s, or 3 u32s if timestamp recorded */ - u32 ptr; /* SRAM byte address of log data */ - u32 ev, time, data; /* event log data */ - - if (num_events == 0) - return; - if (priv->ucode_type == UCODE_INIT) - base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr); - else - base = le32_to_cpu(priv->card_alive.log_event_table_ptr); - - if (mode == 0) - event_size = 2 * sizeof(u32); - else - event_size = 3 * sizeof(u32); - - ptr = base + EVENT_START_OFFSET + (start_idx * event_size); - - /* "time" is actually "data" for mode 0 (no timestamp). - * place event id # at far right for easier visual parsing. */ - for (i = 0; i < num_events; i++) { - ev = iwl_read_targ_mem(priv, ptr); - ptr += sizeof(u32); - time = iwl_read_targ_mem(priv, ptr); - ptr += sizeof(u32); - if (mode == 0) { - /* data, ev */ - IWL_ERR(priv, "EVT_LOG:0x%08x:%04u\n", time, ev); - } else { - data = iwl_read_targ_mem(priv, ptr); - ptr += sizeof(u32); - IWL_ERR(priv, "EVT_LOGT:%010u:0x%08x:%04u\n", - time, data, ev); - } - } -} - -void iwl_dump_nic_event_log(struct iwl_priv *priv) -{ - u32 base; /* SRAM byte address of event log header */ - u32 capacity; /* event log capacity in # entries */ - u32 mode; /* 0 - no timestamp, 1 - timestamp recorded */ - u32 num_wraps; /* # times uCode wrapped to top of log */ - u32 next_entry; /* index of next entry to be written by uCode */ - u32 size; /* # entries that we'll print */ - - if (priv->ucode_type == UCODE_INIT) - base = le32_to_cpu(priv->card_alive_init.log_event_table_ptr); - else - base = le32_to_cpu(priv->card_alive.log_event_table_ptr); - - if (!priv->cfg->ops->lib->is_valid_rtc_data_addr(base)) { - IWL_ERR(priv, "Invalid event log pointer 0x%08X\n", base); - return; - } - - /* event log header */ - capacity = iwl_read_targ_mem(priv, base); - mode = iwl_read_targ_mem(priv, base + (1 * sizeof(u32))); - num_wraps = iwl_read_targ_mem(priv, base + (2 * sizeof(u32))); - next_entry = iwl_read_targ_mem(priv, base + (3 * sizeof(u32))); - - size = num_wraps ? capacity : next_entry; - - /* bail out if nothing in log */ - if (size == 0) { - IWL_ERR(priv, "Start IWL Event Log Dump: nothing in log\n"); - return; - } - - IWL_ERR(priv, "Start IWL Event Log Dump: display count %d, wraps %d\n", - size, num_wraps); - - /* if uCode has wrapped back to top of log, start at the oldest entry, - * i.e the next one that uCode would fill. */ - if (num_wraps) - iwl_print_event_log(priv, next_entry, - capacity - next_entry, mode); - /* (then/else) start at top of log */ - iwl_print_event_log(priv, 0, next_entry, mode); - -} #endif /** * iwl_irq_handle_error - called for HW or SW error interrupt from card @@ -1506,8 +1323,8 @@ void iwl_irq_handle_error(struct iwl_priv *priv) #ifdef CONFIG_IWLWIFI_DEBUG if (iwl_get_debug_level(priv) & IWL_DL_FW_ERRORS) { - iwl_dump_nic_error_log(priv); - iwl_dump_nic_event_log(priv); + priv->cfg->ops->lib->dump_nic_error_log(priv); + priv->cfg->ops->lib->dump_nic_event_log(priv); iwl_print_rx_config_cmd(priv); } #endif @@ -1585,9 +1402,12 @@ int iwl_setup_mac(struct iwl_priv *priv) hw->flags = IEEE80211_HW_SIGNAL_DBM | IEEE80211_HW_NOISE_DBM | IEEE80211_HW_AMPDU_AGGREGATION | - IEEE80211_HW_SPECTRUM_MGMT | - IEEE80211_HW_SUPPORTS_PS | - IEEE80211_HW_SUPPORTS_DYNAMIC_PS; + IEEE80211_HW_SPECTRUM_MGMT; + + if (!priv->cfg->broken_powersave) + hw->flags |= IEEE80211_HW_SUPPORTS_PS | + IEEE80211_HW_SUPPORTS_DYNAMIC_PS; + hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | BIT(NL80211_IFTYPE_ADHOC); diff --git a/drivers/net/wireless/iwlwifi/iwl-core.h b/drivers/net/wireless/iwlwifi/iwl-core.h index c04d2a27081..e50103a956b 100644 --- a/drivers/net/wireless/iwlwifi/iwl-core.h +++ b/drivers/net/wireless/iwlwifi/iwl-core.h @@ -166,6 +166,8 @@ struct iwl_lib_ops { int (*is_valid_rtc_data_addr)(u32 addr); /* 1st ucode load */ int (*load_ucode)(struct iwl_priv *priv); + void (*dump_nic_event_log)(struct iwl_priv *priv); + void (*dump_nic_error_log)(struct iwl_priv *priv); /* power management */ struct iwl_apm_ops apm_ops; @@ -252,6 +254,7 @@ struct iwl_cfg { const u16 max_ll_items; const bool shadow_ram_support; const bool ht_greenfield_support; + const bool broken_powersave; }; /*************************** @@ -539,7 +542,19 @@ int iwl_pci_resume(struct pci_dev *pdev); /***************************************************** * Error Handling Debugging ******************************************************/ +#ifdef CONFIG_IWLWIFI_DEBUG void iwl_dump_nic_event_log(struct iwl_priv *priv); +void iwl_dump_nic_error_log(struct iwl_priv *priv); +#else +static inline void iwl_dump_nic_event_log(struct iwl_priv *priv) +{ +} + +static inline void iwl_dump_nic_error_log(struct iwl_priv *priv) +{ +} +#endif + void iwl_clear_isr_stats(struct iwl_priv *priv); /***************************************************** diff --git a/drivers/net/wireless/iwlwifi/iwl-debugfs.c b/drivers/net/wireless/iwlwifi/iwl-debugfs.c index fb844859a44..a198bcf6102 100644 --- a/drivers/net/wireless/iwlwifi/iwl-debugfs.c +++ b/drivers/net/wireless/iwlwifi/iwl-debugfs.c @@ -410,7 +410,7 @@ static ssize_t iwl_dbgfs_nvm_read(struct file *file, pos += scnprintf(buf + pos, buf_size - pos, "0x%.4x ", ofs); hex_dump_to_buffer(ptr + ofs, 16 , 16, 2, buf + pos, buf_size - pos, 0); - pos += strlen(buf); + pos += strlen(buf + pos); if (buf_size - pos > 0) buf[pos++] = '\n'; } @@ -436,7 +436,7 @@ static ssize_t iwl_dbgfs_log_event_write(struct file *file, if (sscanf(buf, "%d", &event_log_flag) != 1) return -EFAULT; if (event_log_flag == 1) - iwl_dump_nic_event_log(priv); + priv->cfg->ops->lib->dump_nic_event_log(priv); return count; } @@ -909,7 +909,7 @@ static ssize_t iwl_dbgfs_traffic_log_read(struct file *file, "0x%.4x ", ofs); hex_dump_to_buffer(ptr + ofs, 16, 16, 2, buf + pos, bufsz - pos, 0); - pos += strlen(buf); + pos += strlen(buf + pos); if (bufsz - pos > 0) buf[pos++] = '\n'; } @@ -932,7 +932,7 @@ static ssize_t iwl_dbgfs_traffic_log_read(struct file *file, "0x%.4x ", ofs); hex_dump_to_buffer(ptr + ofs, 16, 16, 2, buf + pos, bufsz - pos, 0); - pos += strlen(buf); + pos += strlen(buf + pos); if (bufsz - pos > 0) buf[pos++] = '\n'; } diff --git a/drivers/net/wireless/iwlwifi/iwl-power.c b/drivers/net/wireless/iwlwifi/iwl-power.c index 4ec6a8307cc..60be976afff 100644 --- a/drivers/net/wireless/iwlwifi/iwl-power.c +++ b/drivers/net/wireless/iwlwifi/iwl-power.c @@ -292,8 +292,9 @@ int iwl_power_update_mode(struct iwl_priv *priv, bool force) else dtimper = 1; - /* TT power setting overwrites everything */ - if (tt->state >= IWL_TI_1) + if (priv->cfg->broken_powersave) + iwl_power_sleep_cam_cmd(priv, &cmd); + else if (tt->state >= IWL_TI_1) iwl_static_sleep_cmd(priv, &cmd, tt->tt_power_mode, dtimper); else if (!enabled) iwl_power_sleep_cam_cmd(priv, &cmd); diff --git a/drivers/net/wireless/iwlwifi/iwl-rx.c b/drivers/net/wireless/iwlwifi/iwl-rx.c index 8150c5c3a16..8e1bb53c0aa 100644 --- a/drivers/net/wireless/iwlwifi/iwl-rx.c +++ b/drivers/net/wireless/iwlwifi/iwl-rx.c @@ -239,33 +239,51 @@ void iwl_rx_allocate(struct iwl_priv *priv, gfp_t priority) struct iwl_rx_queue *rxq = &priv->rxq; struct list_head *element; struct iwl_rx_mem_buffer *rxb; + struct sk_buff *skb; unsigned long flags; while (1) { spin_lock_irqsave(&rxq->lock, flags); - if (list_empty(&rxq->rx_used)) { spin_unlock_irqrestore(&rxq->lock, flags); return; } - element = rxq->rx_used.next; - rxb = list_entry(element, struct iwl_rx_mem_buffer, list); - list_del(element); - spin_unlock_irqrestore(&rxq->lock, flags); + if (rxq->free_count > RX_LOW_WATERMARK) + priority |= __GFP_NOWARN; /* Alloc a new receive buffer */ - rxb->skb = alloc_skb(priv->hw_params.rx_buf_size + 256, + skb = alloc_skb(priv->hw_params.rx_buf_size + 256, priority); - if (!rxb->skb) { - IWL_CRIT(priv, "Can not allocate SKB buffers\n"); + if (!skb) { + if (net_ratelimit()) + IWL_DEBUG_INFO(priv, "Failed to allocate SKB buffer.\n"); + if ((rxq->free_count <= RX_LOW_WATERMARK) && + net_ratelimit()) + IWL_CRIT(priv, "Failed to allocate SKB buffer with %s. Only %u free buffers remaining.\n", + priority == GFP_ATOMIC ? "GFP_ATOMIC" : "GFP_KERNEL", + rxq->free_count); /* We don't reschedule replenish work here -- we will * call the restock method and if it still needs * more buffers it will schedule replenish */ break; } + spin_lock_irqsave(&rxq->lock, flags); + + if (list_empty(&rxq->rx_used)) { + spin_unlock_irqrestore(&rxq->lock, flags); + dev_kfree_skb_any(skb); + return; + } + element = rxq->rx_used.next; + rxb = list_entry(element, struct iwl_rx_mem_buffer, list); + list_del(element); + + spin_unlock_irqrestore(&rxq->lock, flags); + + rxb->skb = skb; /* Get physical address of RB/SKB */ rxb->real_dma_addr = pci_map_single( priv->pci_dev, diff --git a/drivers/net/wireless/iwlwifi/iwl-sta.c b/drivers/net/wireless/iwlwifi/iwl-sta.c index a2b9ec82b96..c6633fec821 100644 --- a/drivers/net/wireless/iwlwifi/iwl-sta.c +++ b/drivers/net/wireless/iwlwifi/iwl-sta.c @@ -520,7 +520,7 @@ int iwl_send_static_wepkey_cmd(struct iwl_priv *priv, u8 send_if_empty) struct iwl_host_cmd cmd = { .id = REPLY_WEPKEY, .data = wep_cmd, - .flags = CMD_SYNC, + .flags = CMD_ASYNC, }; memset(wep_cmd, 0, cmd_size + diff --git a/drivers/net/wireless/iwlwifi/iwl-tx.c b/drivers/net/wireless/iwlwifi/iwl-tx.c index a7422e52d88..c1890754470 100644 --- a/drivers/net/wireless/iwlwifi/iwl-tx.c +++ b/drivers/net/wireless/iwlwifi/iwl-tx.c @@ -197,6 +197,12 @@ void iwl_cmd_queue_free(struct iwl_priv *priv) pci_free_consistent(dev, priv->hw_params.tfd_size * txq->q.n_bd, txq->tfds, txq->q.dma_addr); + /* deallocate arrays */ + kfree(txq->cmd); + kfree(txq->meta); + txq->cmd = NULL; + txq->meta = NULL; + /* 0-fill queue descriptor structure */ memset(txq, 0, sizeof(*txq)); } diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 2238c9f2018..c390dbd877e 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -1134,6 +1134,7 @@ static void iwl3945_rx_allocate(struct iwl_priv *priv, gfp_t priority) struct iwl_rx_queue *rxq = &priv->rxq; struct list_head *element; struct iwl_rx_mem_buffer *rxb; + struct sk_buff *skb; unsigned long flags; while (1) { @@ -1143,25 +1144,39 @@ static void iwl3945_rx_allocate(struct iwl_priv *priv, gfp_t priority) spin_unlock_irqrestore(&rxq->lock, flags); return; } - - element = rxq->rx_used.next; - rxb = list_entry(element, struct iwl_rx_mem_buffer, list); - list_del(element); spin_unlock_irqrestore(&rxq->lock, flags); + if (rxq->free_count > RX_LOW_WATERMARK) + priority |= __GFP_NOWARN; /* Alloc a new receive buffer */ - rxb->skb = - alloc_skb(priv->hw_params.rx_buf_size, - priority); - if (!rxb->skb) { + skb = alloc_skb(priv->hw_params.rx_buf_size, priority); + if (!skb) { if (net_ratelimit()) - IWL_CRIT(priv, ": Can not allocate SKB buffers\n"); + IWL_DEBUG_INFO(priv, "Failed to allocate SKB buffer.\n"); + if ((rxq->free_count <= RX_LOW_WATERMARK) && + net_ratelimit()) + IWL_CRIT(priv, "Failed to allocate SKB buffer with %s. Only %u free buffers remaining.\n", + priority == GFP_ATOMIC ? "GFP_ATOMIC" : "GFP_KERNEL", + rxq->free_count); /* We don't reschedule replenish work here -- we will * call the restock method and if it still needs * more buffers it will schedule replenish */ break; } + spin_lock_irqsave(&rxq->lock, flags); + if (list_empty(&rxq->rx_used)) { + spin_unlock_irqrestore(&rxq->lock, flags); + dev_kfree_skb_any(skb); + return; + } + element = rxq->rx_used.next; + rxb = list_entry(element, struct iwl_rx_mem_buffer, list); + list_del(element); + spin_unlock_irqrestore(&rxq->lock, flags); + + rxb->skb = skb; + /* If radiotap head is required, reserve some headroom here. * The physical head count is a variable rx_stats->phy_count. * We reserve 4 bytes here. Plus these extra bytes, the @@ -1466,6 +1481,7 @@ static inline void iwl_synchronize_irq(struct iwl_priv *priv) tasklet_kill(&priv->irq_tasklet); } +#ifdef CONFIG_IWLWIFI_DEBUG static const char *desc_lookup(int i) { switch (i) { @@ -1489,7 +1505,7 @@ static const char *desc_lookup(int i) #define ERROR_START_OFFSET (1 * sizeof(u32)) #define ERROR_ELEM_SIZE (7 * sizeof(u32)) -static void iwl3945_dump_nic_error_log(struct iwl_priv *priv) +void iwl3945_dump_nic_error_log(struct iwl_priv *priv) { u32 i; u32 desc, time, count, base, data1; @@ -1583,7 +1599,7 @@ static void iwl3945_print_event_log(struct iwl_priv *priv, u32 start_idx, } } -static void iwl3945_dump_nic_event_log(struct iwl_priv *priv) +void iwl3945_dump_nic_event_log(struct iwl_priv *priv) { u32 base; /* SRAM byte address of event log header */ u32 capacity; /* event log capacity in # entries */ @@ -1625,6 +1641,16 @@ static void iwl3945_dump_nic_event_log(struct iwl_priv *priv) iwl3945_print_event_log(priv, 0, next_entry, mode); } +#else +void iwl3945_dump_nic_event_log(struct iwl_priv *priv) +{ +} + +void iwl3945_dump_nic_error_log(struct iwl_priv *priv) +{ +} + +#endif static void iwl3945_irq_tasklet(struct iwl_priv *priv) { @@ -3668,21 +3694,6 @@ static ssize_t dump_error_log(struct device *d, static DEVICE_ATTR(dump_errors, S_IWUSR, NULL, dump_error_log); -static ssize_t dump_event_log(struct device *d, - struct device_attribute *attr, - const char *buf, size_t count) -{ - struct iwl_priv *priv = dev_get_drvdata(d); - char *p = (char *)buf; - - if (p[0] == '1') - iwl3945_dump_nic_event_log(priv); - - return strnlen(buf, count); -} - -static DEVICE_ATTR(dump_events, S_IWUSR, NULL, dump_event_log); - /***************************************************************************** * * driver setup and tear down @@ -3727,7 +3738,6 @@ static struct attribute *iwl3945_sysfs_entries[] = { &dev_attr_antenna.attr, &dev_attr_channels.attr, &dev_attr_dump_errors.attr, - &dev_attr_dump_events.attr, &dev_attr_flags.attr, &dev_attr_filter_flags.attr, #ifdef CONFIG_IWL3945_SPECTRUM_MEASUREMENT diff --git a/drivers/net/wireless/libertas/if_spi.c b/drivers/net/wireless/libertas/if_spi.c index 446e327180f..cb8be8d7abc 100644 --- a/drivers/net/wireless/libertas/if_spi.c +++ b/drivers/net/wireless/libertas/if_spi.c @@ -1222,3 +1222,4 @@ MODULE_DESCRIPTION("Libertas SPI WLAN Driver"); MODULE_AUTHOR("Andrey Yurovsky <andrey@cozybit.com>, " "Colin McCabe <colin@cozybit.com>"); MODULE_LICENSE("GPL"); +MODULE_ALIAS("spi:libertas_spi"); diff --git a/drivers/net/wireless/p54/p54spi.c b/drivers/net/wireless/p54/p54spi.c index 05458d9249c..afd26bf0664 100644 --- a/drivers/net/wireless/p54/p54spi.c +++ b/drivers/net/wireless/p54/p54spi.c @@ -731,3 +731,4 @@ module_exit(p54spi_exit); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Christian Lamparter <chunkeey@web.de>"); +MODULE_ALIAS("spi:cx3110x"); diff --git a/drivers/net/wireless/p54/p54usb.c b/drivers/net/wireless/p54/p54usb.c index e44460ff149..17e199546ee 100644 --- a/drivers/net/wireless/p54/p54usb.c +++ b/drivers/net/wireless/p54/p54usb.c @@ -67,6 +67,7 @@ static struct usb_device_id p54u_table[] __devinitdata = { {USB_DEVICE(0x0bf8, 0x1009)}, /* FUJITSU E-5400 USB D1700*/ {USB_DEVICE(0x0cde, 0x0006)}, /* Medion MD40900 */ {USB_DEVICE(0x0cde, 0x0008)}, /* Sagem XG703A */ + {USB_DEVICE(0x0cde, 0x0015)}, /* Zcomax XG-705A */ {USB_DEVICE(0x0d8e, 0x3762)}, /* DLink DWL-G120 Cohiba */ {USB_DEVICE(0x124a, 0x4025)}, /* IOGear GWU513 (GW3887IK chip) */ {USB_DEVICE(0x1260, 0xee22)}, /* SMC 2862W-G version 2 */ diff --git a/drivers/net/wireless/rt2x00/rt2x00lib.h b/drivers/net/wireless/rt2x00/rt2x00lib.h index 5462cb5ad99..567f029a8cd 100644 --- a/drivers/net/wireless/rt2x00/rt2x00lib.h +++ b/drivers/net/wireless/rt2x00/rt2x00lib.h @@ -380,7 +380,7 @@ static inline void rt2x00crypto_tx_insert_iv(struct sk_buff *skb, { } -static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb, bool l2pad, +static inline void rt2x00crypto_rx_insert_iv(struct sk_buff *skb, unsigned int header_length, struct rxdone_entry_desc *rxdesc) { diff --git a/drivers/net/wireless/wl12xx/Kconfig b/drivers/net/wireless/wl12xx/Kconfig index 7b14d5bc63d..88060e11754 100644 --- a/drivers/net/wireless/wl12xx/Kconfig +++ b/drivers/net/wireless/wl12xx/Kconfig @@ -1,5 +1,5 @@ menuconfig WL12XX - boolean "TI wl12xx driver support" + tristate "TI wl12xx driver support" depends on MAC80211 && WLAN_80211 && EXPERIMENTAL ---help--- This will enable TI wl12xx driver support. The drivers make diff --git a/drivers/net/wireless/wl12xx/wl1251_main.c b/drivers/net/wireless/wl12xx/wl1251_main.c index 5809ef5b18f..1103256ad98 100644 --- a/drivers/net/wireless/wl12xx/wl1251_main.c +++ b/drivers/net/wireless/wl12xx/wl1251_main.c @@ -1426,3 +1426,4 @@ EXPORT_SYMBOL_GPL(wl1251_free_hw); MODULE_DESCRIPTION("TI wl1251 Wireles LAN Driver Core"); MODULE_LICENSE("GPL"); MODULE_AUTHOR("Kalle Valo <kalle.valo@nokia.com>"); +MODULE_ALIAS("spi:wl12xx"); diff --git a/drivers/net/wireless/wl12xx/wl1271_main.c b/drivers/net/wireless/wl12xx/wl1271_main.c index d9169b47ac4..27298b19d5b 100644 --- a/drivers/net/wireless/wl12xx/wl1271_main.c +++ b/drivers/net/wireless/wl12xx/wl1271_main.c @@ -644,11 +644,10 @@ static int wl1271_op_config_interface(struct ieee80211_hw *hw, { struct wl1271 *wl = hw->priv; struct sk_buff *beacon; - DECLARE_MAC_BUF(mac); int ret; - wl1271_debug(DEBUG_MAC80211, "mac80211 config_interface bssid %s", - print_mac(mac, conf->bssid)); + wl1271_debug(DEBUG_MAC80211, "mac80211 config_interface bssid %pM", + conf->bssid); wl1271_dump_ascii(DEBUG_MAC80211, "ssid: ", conf->ssid, conf->ssid_len); diff --git a/drivers/net/wireless/zd1211rw/zd_chip.c b/drivers/net/wireless/zd1211rw/zd_chip.c index 5e110a2328a..4e79a980013 100644 --- a/drivers/net/wireless/zd1211rw/zd_chip.c +++ b/drivers/net/wireless/zd1211rw/zd_chip.c @@ -368,7 +368,7 @@ error: return r; } -/* MAC address: if custom mac addresses are to to be used CR_MAC_ADDR_P1 and +/* MAC address: if custom mac addresses are to be used CR_MAC_ADDR_P1 and * CR_MAC_ADDR_P2 must be overwritten */ int zd_write_mac_addr(struct zd_chip *chip, const u8 *mac_addr) diff --git a/drivers/net/wireless/zd1211rw/zd_usb.c b/drivers/net/wireless/zd1211rw/zd_usb.c index 38688847d56..23a6a6d4863 100644 --- a/drivers/net/wireless/zd1211rw/zd_usb.c +++ b/drivers/net/wireless/zd1211rw/zd_usb.c @@ -1070,7 +1070,7 @@ static int eject_installer(struct usb_interface *intf) /* Find bulk out endpoint */ endpoint = &iface_desc->endpoint[1].desc; - if ((endpoint->bEndpointAddress & USB_TYPE_MASK) == USB_DIR_OUT && + if (usb_endpoint_dir_out(endpoint) && usb_endpoint_xfer_bulk(endpoint)) { bulk_out_ep = endpoint->bEndpointAddress; } else { diff --git a/drivers/net/xilinx_emaclite.c b/drivers/net/xilinx_emaclite.c index dc22782633a..83a044dbd1d 100644 --- a/drivers/net/xilinx_emaclite.c +++ b/drivers/net/xilinx_emaclite.c @@ -134,18 +134,15 @@ static void xemaclite_enable_interrupts(struct net_local *drvdata) } /* Enable the Rx interrupts for the first buffer */ - reg_data = in_be32(drvdata->base_addr + XEL_RSR_OFFSET); out_be32(drvdata->base_addr + XEL_RSR_OFFSET, - reg_data | XEL_RSR_RECV_IE_MASK); + XEL_RSR_RECV_IE_MASK); /* Enable the Rx interrupts for the second Buffer if * configured in HW */ if (drvdata->rx_ping_pong != 0) { - reg_data = in_be32(drvdata->base_addr + XEL_BUFFER_OFFSET + - XEL_RSR_OFFSET); out_be32(drvdata->base_addr + XEL_BUFFER_OFFSET + XEL_RSR_OFFSET, - reg_data | XEL_RSR_RECV_IE_MASK); + XEL_RSR_RECV_IE_MASK); } /* Enable the Global Interrupt Enable */ |