diff options
Diffstat (limited to 'drivers/net')
74 files changed, 6243 insertions, 2661 deletions
diff --git a/drivers/net/8139cp.c b/drivers/net/8139cp.c index a804965e654..58bbc3e6d0d 100644 --- a/drivers/net/8139cp.c +++ b/drivers/net/8139cp.c @@ -107,11 +107,6 @@ MODULE_PARM_DESC (multicast_filter_limit, "8139cp: maximum number of filtered mu #define PFX DRV_NAME ": " -#ifndef TRUE -#define FALSE 0 -#define TRUE (!FALSE) -#endif - #define CP_DEF_MSG_ENABLE (NETIF_MSG_DRV | \ NETIF_MSG_PROBE | \ NETIF_MSG_LINK) @@ -661,7 +656,7 @@ static irqreturn_t cp_interrupt (int irq, void *dev_instance) if (status & (TxOK | TxErr | TxEmpty | SWInt)) cp_tx(cp); if (status & LinkChg) - mii_check_media(&cp->mii_if, netif_msg_link(cp), FALSE); + mii_check_media(&cp->mii_if, netif_msg_link(cp), false); spin_unlock(&cp->lock); @@ -1188,7 +1183,7 @@ static int cp_open (struct net_device *dev) goto err_out_hw; netif_carrier_off(dev); - mii_check_media(&cp->mii_if, netif_msg_link(cp), TRUE); + mii_check_media(&cp->mii_if, netif_msg_link(cp), true); netif_start_queue(dev); return 0; @@ -2050,7 +2045,7 @@ static int cp_resume (struct pci_dev *pdev) spin_lock_irqsave (&cp->lock, flags); - mii_check_media(&cp->mii_if, netif_msg_link(cp), FALSE); + mii_check_media(&cp->mii_if, netif_msg_link(cp), false); spin_unlock_irqrestore (&cp->lock, flags); diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index b49375abb5f..5cc3d517e39 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -3,10 +3,7 @@ # Network device configuration # -menu "Network device support" - depends on NET - -config NETDEVICES +menuconfig NETDEVICES default y if UML bool "Network device support" ---help--- @@ -151,11 +148,9 @@ source "drivers/net/phy/Kconfig" # Ethernet # -menu "Ethernet (10 or 100Mbit)" - depends on !UML - -config NET_ETHERNET +menuconfig NET_ETHERNET bool "Ethernet (10 or 100Mbit)" + depends on !UML ---help--- Ethernet (also called IEEE 802.3 or ISO 8802-2) is the most common type of Local Area Network (LAN) in universities and companies. @@ -180,9 +175,10 @@ config NET_ETHERNET kernel: saying N will just cause the configurator to skip all the questions about Ethernet network cards. If unsure, say N. +if NET_ETHERNET + config MII tristate "Generic Media Independent Interface device support" - depends on NET_ETHERNET help Most ethernet controllers have MII transceiver either as an external or internal device. It is safe to say Y or M here even if your @@ -190,7 +186,7 @@ config MII config MACB tristate "Atmel MACB support" - depends on NET_ETHERNET && (AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263) + depends on AVR32 || ARCH_AT91SAM9260 || ARCH_AT91SAM9263 select MII help The Atmel MACB ethernet interface is found on many AT32 and AT91 @@ -203,7 +199,7 @@ source "drivers/net/arm/Kconfig" config MACE tristate "MACE (Power Mac ethernet) support" - depends on NET_ETHERNET && PPC_PMAC && PPC32 + depends on PPC_PMAC && PPC32 select CRC32 help Power Macintoshes and clones with Ethernet built-in on the @@ -226,7 +222,7 @@ config MACE_AAUI_PORT config BMAC tristate "BMAC (G3 ethernet) support" - depends on NET_ETHERNET && PPC_PMAC && PPC32 + depends on PPC_PMAC && PPC32 select CRC32 help Say Y for support of BMAC Ethernet interfaces. These are used on G3 @@ -237,7 +233,7 @@ config BMAC config ARIADNE tristate "Ariadne support" - depends on NET_ETHERNET && ZORRO + depends on ZORRO help If you have a Village Tronic Ariadne Ethernet adapter, say Y. Otherwise, say N. @@ -247,7 +243,7 @@ config ARIADNE config A2065 tristate "A2065 support" - depends on NET_ETHERNET && ZORRO + depends on ZORRO select CRC32 help If you have a Commodore A2065 Ethernet adapter, say Y. Otherwise, @@ -258,7 +254,7 @@ config A2065 config HYDRA tristate "Hydra support" - depends on NET_ETHERNET && ZORRO + depends on ZORRO select CRC32 help If you have a Hydra Ethernet adapter, say Y. Otherwise, say N. @@ -268,7 +264,7 @@ config HYDRA config ZORRO8390 tristate "Zorro NS8390-based Ethernet support" - depends on NET_ETHERNET && ZORRO + depends on ZORRO select CRC32 help This driver is for Zorro Ethernet cards using an NS8390-compatible @@ -281,7 +277,7 @@ config ZORRO8390 config APNE tristate "PCMCIA NE2000 support" - depends on NET_ETHERNET && AMIGA_PCMCIA + depends on AMIGA_PCMCIA select CRC32 help If you have a PCMCIA NE2000 compatible adapter, say Y. Otherwise, @@ -292,7 +288,7 @@ config APNE config APOLLO_ELPLUS tristate "Apollo 3c505 support" - depends on NET_ETHERNET && APOLLO + depends on APOLLO help Say Y or M here if your Apollo has a 3Com 3c505 ISA Ethernet card. If you don't have one made for Apollos, you can use one from a PC, @@ -301,7 +297,7 @@ config APOLLO_ELPLUS config MAC8390 bool "Macintosh NS 8390 based ethernet cards" - depends on NET_ETHERNET && MAC + depends on MAC select CRC32 help If you want to include a driver to support Nubus or LC-PDS @@ -311,7 +307,7 @@ config MAC8390 config MAC89x0 tristate "Macintosh CS89x0 based ethernet cards" - depends on NET_ETHERNET && MAC + depends on MAC ---help--- Support for CS89x0 chipset based Ethernet cards. If you have a Nubus or LC-PDS network (Ethernet) card of this type, say Y and @@ -324,7 +320,7 @@ config MAC89x0 config MACSONIC tristate "Macintosh SONIC based ethernet (onboard, NuBus, LC, CS)" - depends on NET_ETHERNET && MAC + depends on MAC ---help--- Support for NatSemi SONIC based Ethernet devices. This includes the onboard Ethernet in many Quadras as well as some LC-PDS, @@ -338,7 +334,7 @@ config MACSONIC config MACMACE bool "Macintosh (AV) onboard MACE ethernet" - depends on NET_ETHERNET && MAC + depends on MAC select CRC32 help Support for the onboard AMD 79C940 MACE Ethernet controller used in @@ -348,7 +344,7 @@ config MACMACE config MVME147_NET tristate "MVME147 (Lance) Ethernet support" - depends on NET_ETHERNET && MVME147 + depends on MVME147 select CRC32 help Support for the on-board Ethernet interface on the Motorola MVME147 @@ -358,7 +354,7 @@ config MVME147_NET config MVME16x_NET tristate "MVME16x Ethernet support" - depends on NET_ETHERNET && MVME16x + depends on MVME16x help This is the driver for the Ethernet interface on the Motorola MVME162, 166, 167, 172 and 177 boards. Say Y here to include the @@ -367,7 +363,7 @@ config MVME16x_NET config BVME6000_NET tristate "BVME6000 Ethernet support" - depends on NET_ETHERNET && BVME6000 + depends on BVME6000 help This is the driver for the Ethernet interface on BVME4000 and BVME6000 VME boards. Say Y here to include the driver for this chip @@ -376,7 +372,7 @@ config BVME6000_NET config ATARILANCE tristate "Atari Lance support" - depends on NET_ETHERNET && ATARI + depends on ATARI help Say Y to include support for several Atari Ethernet adapters based on the AMD Lance chipset: RieblCard (with or without battery), or @@ -384,7 +380,7 @@ config ATARILANCE config ATARI_BIONET tristate "BioNet-100 support" - depends on NET_ETHERNET && ATARI && ATARI_ACSI && BROKEN + depends on ATARI && ATARI_ACSI && BROKEN help Say Y to include support for BioData's BioNet-100 Ethernet adapter for the ACSI port. The driver works (has to work...) with a polled @@ -392,7 +388,7 @@ config ATARI_BIONET config ATARI_PAMSNET tristate "PAMsNet support" - depends on NET_ETHERNET && ATARI && ATARI_ACSI && BROKEN + depends on ATARI && ATARI_ACSI && BROKEN help Say Y to include support for the PAMsNet Ethernet adapter for the ACSI port ("ACSI node"). The driver works (has to work...) with a @@ -400,7 +396,7 @@ config ATARI_PAMSNET config SUN3LANCE tristate "Sun3/Sun3x on-board LANCE support" - depends on NET_ETHERNET && (SUN3 || SUN3X) + depends on SUN3 || SUN3X help Most Sun3 and Sun3x motherboards (including the 3/50, 3/60 and 3/80) featured an AMD Lance 10Mbit Ethernet controller on board; say Y @@ -413,7 +409,7 @@ config SUN3LANCE config SUN3_82586 bool "Sun3 on-board Intel 82586 support" - depends on NET_ETHERNET && SUN3 + depends on SUN3 help This driver enables support for the on-board Intel 82586 based Ethernet adapter found on Sun 3/1xx and 3/2xx motherboards. Note @@ -422,7 +418,7 @@ config SUN3_82586 config HPLANCE bool "HP on-board LANCE support" - depends on NET_ETHERNET && DIO + depends on DIO select CRC32 help If you want to use the builtin "LANCE" Ethernet controller on an @@ -430,21 +426,28 @@ config HPLANCE config LASI_82596 tristate "Lasi ethernet" - depends on NET_ETHERNET && GSC + depends on GSC help Say Y here to support the builtin Intel 82596 ethernet controller found in Hewlett-Packard PA-RISC machines with 10Mbit ethernet. +config SNI_82596 + tristate "SNI RM ethernet" + depends on NET_ETHERNET && SNI_RM + help + Say Y here to support the on-board Intel 82596 ethernet controller + built into SNI RM machines. + config MIPS_JAZZ_SONIC tristate "MIPS JAZZ onboard SONIC Ethernet support" - depends on NET_ETHERNET && MACH_JAZZ + depends on MACH_JAZZ help This is the driver for the onboard card of MIPS Magnum 4000, Acer PICA, Olivetti M700-10 and a few other identical OEM systems. config MIPS_AU1X00_ENET bool "MIPS AU1000 Ethernet support" - depends on NET_ETHERNET && SOC_AU1X00 + depends on SOC_AU1X00 select PHYLIB select CRC32 help @@ -453,11 +456,11 @@ config MIPS_AU1X00_ENET config NET_SB1250_MAC tristate "SB1250 Ethernet support" - depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC + depends on SIBYTE_SB1xxx_SOC config SGI_IOC3_ETH bool "SGI IOC3 Ethernet" - depends on NET_ETHERNET && PCI && SGI_IP27 + depends on PCI && SGI_IP27 select CRC32 select MII help @@ -487,7 +490,7 @@ config SGI_IOC3_ETH_HW_TX_CSUM config MIPS_SIM_NET tristate "MIPS simulator Network device" - depends on NET_ETHERNET && MIPS_SIM + depends on MIPS_SIM help The MIPSNET device is a simple Ethernet network device which is emulated by the MIPS Simulator. @@ -495,11 +498,11 @@ config MIPS_SIM_NET config SGI_O2MACE_ETH tristate "SGI O2 MACE Fast Ethernet support" - depends on NET_ETHERNET && SGI_IP32=y + depends on SGI_IP32=y config STNIC tristate "National DP83902AV support" - depends on NET_ETHERNET && SUPERH + depends on SUPERH select CRC32 help Support for cards based on the National Semiconductor DP83902AV @@ -511,7 +514,7 @@ config STNIC config SUNLANCE tristate "Sun LANCE support" - depends on NET_ETHERNET && SBUS + depends on SBUS select CRC32 help This driver supports the "le" interface present on all 32-bit Sparc @@ -524,7 +527,7 @@ config SUNLANCE config HAPPYMEAL tristate "Sun Happy Meal 10/100baseT support" - depends on NET_ETHERNET && (SBUS || PCI) + depends on SBUS || PCI select CRC32 help This driver supports the "hme" interface present on most Ultra @@ -537,7 +540,7 @@ config HAPPYMEAL config SUNBMAC tristate "Sun BigMAC 10/100baseT support (EXPERIMENTAL)" - depends on NET_ETHERNET && SBUS && EXPERIMENTAL + depends on SBUS && EXPERIMENTAL select CRC32 help This driver supports the "be" interface available as an Sbus option. @@ -548,7 +551,7 @@ config SUNBMAC config SUNQE tristate "Sun QuadEthernet support" - depends on NET_ETHERNET && SBUS + depends on SBUS select CRC32 help This driver supports the "qe" 10baseT Ethernet device, available as @@ -560,7 +563,7 @@ config SUNQE config SUNGEM tristate "Sun GEM support" - depends on NET_ETHERNET && PCI + depends on PCI select CRC32 help Support for the Sun GEM chip, aka Sun GigabitEthernet/P 2.0. See also @@ -568,7 +571,7 @@ config SUNGEM config CASSINI tristate "Sun Cassini support" - depends on NET_ETHERNET && PCI + depends on PCI select CRC32 help Support for the Sun Cassini chip, aka Sun GigaSwift Ethernet. See also @@ -576,7 +579,7 @@ config CASSINI config NET_VENDOR_3COM bool "3COM cards" - depends on NET_ETHERNET && (ISA || EISA || MCA || PCI) + depends on ISA || EISA || MCA || PCI help If you have a network (Ethernet) card belonging to this class, say Y and read the Ethernet-HOWTO, available from @@ -736,7 +739,7 @@ config TYPHOON config LANCE tristate "AMD LANCE and PCnet (AT1500 and NE2100) support" - depends on NET_ETHERNET && ISA && ISA_DMA_API + depends on ISA && ISA_DMA_API help If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from @@ -748,7 +751,7 @@ config LANCE config NET_VENDOR_SMC bool "Western Digital/SMC cards" - depends on NET_ETHERNET && (ISA || MCA || EISA || MAC) + depends on ISA || MCA || EISA || MAC help If you have a network (Ethernet) card belonging to this class, say Y and read the Ethernet-HOWTO, available from @@ -818,11 +821,27 @@ config ULTRA32 <file:Documentation/networking/net-modules.txt>. The module will be called smc-ultra32. +config SMC9194 + tristate "SMC 9194 support" + depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN) + select CRC32 + ---help--- + This is support for the SMC9xxx based Ethernet cards. Choose this + option if you have a DELL laptop with the docking station, or + another SMC9192/9194 based chipset. Say Y if you want it compiled + into the kernel, and read the file + <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, + available from <http://www.tldp.org/docs.html#howto>. + + To compile this driver as a module, choose M here and read + <file:Documentation/networking/net-modules.txt>. The module + will be called smc9194. + config SMC91X tristate "SMC 91C9x/91C1xxx support" select CRC32 select MII - depends on NET_ETHERNET && (ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BFIN) + depends on ARM || REDWOOD_5 || REDWOOD_6 || M32R || SUPERH || SOC_AU1X00 || BFIN help This is a driver for SMC's 91x series of Ethernet chipsets, including the SMC91C94 and the SMC91C111. Say Y if you want it @@ -836,26 +855,10 @@ config SMC91X module, say M here and read <file:Documentation/kbuild/modules.txt> as well as <file:Documentation/networking/net-modules.txt>. -config SMC9194 - tristate "SMC 9194 support" - depends on NET_VENDOR_SMC && (ISA || MAC && BROKEN) - select CRC32 - ---help--- - This is support for the SMC9xxx based Ethernet cards. Choose this - option if you have a DELL laptop with the docking station, or - another SMC9192/9194 based chipset. Say Y if you want it compiled - into the kernel, and read the file - <file:Documentation/networking/smc9.txt> and the Ethernet-HOWTO, - available from <http://www.tldp.org/docs.html#howto>. - - To compile this driver as a module, choose M here and read - <file:Documentation/networking/net-modules.txt>. The module - will be called smc9194. - config NET_NETX tristate "NetX Ethernet support" select MII - depends on NET_ETHERNET && ARCH_NETX + depends on ARCH_NETX help This is support for the Hilscher netX builtin Ethernet ports @@ -865,7 +868,7 @@ config NET_NETX config DM9000 tristate "DM9000 support" - depends on (ARM || MIPS) && NET_ETHERNET + depends on ARM || MIPS select CRC32 select MII ---help--- @@ -879,7 +882,7 @@ config SMC911X tristate "SMSC LAN911[5678] support" select CRC32 select MII - depends on NET_ETHERNET && ARCH_PXA + depends on ARCH_PXA help This is a driver for SMSC's LAN911x series of Ethernet chipsets including the new LAN9115, LAN9116, LAN9117, and LAN9118. @@ -893,7 +896,7 @@ config SMC911X config NET_VENDOR_RACAL bool "Racal-Interlan (Micom) NI cards" - depends on NET_ETHERNET && ISA + depends on ISA help If you have a network (Ethernet) card belonging to this class, such as the NI5010, NI5210 or NI6210, say Y and read the Ethernet-HOWTO, @@ -945,7 +948,7 @@ source "drivers/net/tulip/Kconfig" config AT1700 tristate "AT1700/1720 support (EXPERIMENTAL)" - depends on NET_ETHERNET && (ISA || MCA_LEGACY) && EXPERIMENTAL + depends on (ISA || MCA_LEGACY) && EXPERIMENTAL select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read @@ -958,7 +961,7 @@ config AT1700 config DEPCA tristate "DEPCA, DE10x, DE200, DE201, DE202, DE422 support" - depends on NET_ETHERNET && (ISA || EISA || MCA) + depends on ISA || EISA || MCA select CRC32 ---help--- If you have a network (Ethernet) card of this type, say Y and read @@ -972,7 +975,7 @@ config DEPCA config HP100 tristate "HP 10/100VG PCLAN (ISA, EISA, PCI) support" - depends on NET_ETHERNET && (ISA || EISA || PCI) + depends on ISA || EISA || PCI help If you have a network (Ethernet) card of this type, say Y and read the Ethernet-HOWTO, available from @@ -984,7 +987,7 @@ config HP100 config NET_ISA bool "Other ISA cards" - depends on NET_ETHERNET && ISA + depends on ISA ---help--- If your network (Ethernet) card hasn't been mentioned yet and its bus system (that's the way the cards talks to the other components @@ -1147,7 +1150,7 @@ config SEEQ8005 config NE2_MCA tristate "NE/2 (ne2000 MCA version) support" - depends on NET_ETHERNET && MCA_LEGACY + depends on MCA_LEGACY select CRC32 help If you have a network (Ethernet) card of this type, say Y and read @@ -1160,7 +1163,7 @@ config NE2_MCA config IBMLANA tristate "IBM LAN Adapter/A support" - depends on NET_ETHERNET && MCA && MCA_LEGACY + depends on MCA && MCA_LEGACY ---help--- This is a Micro Channel Ethernet adapter. You need to set CONFIG_MCA to use this driver. It is both available as an in-kernel @@ -1176,7 +1179,7 @@ config IBMLANA config IBMVETH tristate "IBM LAN Virtual Ethernet support" - depends on NET_ETHERNET && PPC_PSERIES + depends on PPC_PSERIES ---help--- This driver supports virtual ethernet adapters on newer IBM iSeries and pSeries systems. @@ -1257,7 +1260,7 @@ config IBM_EMAC_TAH config NET_PCI bool "EISA, VLB, PCI and on board controllers" - depends on NET_ETHERNET && (ISA || EISA || PCI) + depends on ISA || EISA || PCI help This is another class of network cards which attach directly to the bus. If you have one of those, say Y and read the Ethernet-HOWTO, @@ -1313,6 +1316,7 @@ config AMD8111_ETH To compile this driver as a module, choose M here and read <file:Documentation/networking/net-modules.txt>. The module will be called amd8111e. + config AMD8111E_NAPI bool "Enable NAPI support" depends on AMD8111_ETH @@ -1778,7 +1782,7 @@ config SC92031 config NET_POCKET bool "Pocket and portable adapters" - depends on NET_ETHERNET && PARPORT + depends on PARPORT ---help--- Cute little network (Ethernet) devices which attach to the parallel port ("pocket adapters"), commonly used with laptops. If you have @@ -1847,14 +1851,14 @@ config DE620 config SGISEEQ tristate "SGI Seeq ethernet controller support" - depends on NET_ETHERNET && SGI_IP22 + depends on SGI_IP22 help Say Y here if you have an Seeq based Ethernet network card. This is used in many Silicon Graphics machines. config DECLANCE tristate "DEC LANCE ethernet controller support" - depends on NET_ETHERNET && MACH_DECSTATION + depends on MACH_DECSTATION select CRC32 help This driver is for the series of Ethernet controllers produced by @@ -1884,7 +1888,7 @@ config FEC2 config NE_H8300 tristate "NE2000 compatible support for H8/300" - depends on H8300 && NET_ETHERNET + depends on H8300 help Say Y here if you want to use the NE2000 compatible controller on the Renesas H8/300 processor. @@ -1892,7 +1896,7 @@ config NE_H8300 source "drivers/net/fec_8xx/Kconfig" source "drivers/net/fs_enet/Kconfig" -endmenu +endif # NET_ETHERNET # # Gigabit Ethernet @@ -2948,8 +2952,6 @@ config NETCONSOLE If you want to log kernel messages over the network, enable this. See <file:Documentation/networking/netconsole.txt> for details. -endif #NETDEVICES - config NETPOLL def_bool NETCONSOLE @@ -2961,4 +2963,4 @@ config NETPOLL_TRAP config NET_POLL_CONTROLLER def_bool NETPOLL -endmenu +endif # NETDEVICES diff --git a/drivers/net/Makefile b/drivers/net/Makefile index a77affa4f6e..eb62fb48e4b 100644 --- a/drivers/net/Makefile +++ b/drivers/net/Makefile @@ -157,6 +157,7 @@ obj-$(CONFIG_ELPLUS) += 3c505.o obj-$(CONFIG_AC3200) += ac3200.o 8390.o obj-$(CONFIG_APRICOT) += 82596.o obj-$(CONFIG_LASI_82596) += lasi_82596.o +obj-$(CONFIG_SNI_82596) += sni_82596.o obj-$(CONFIG_MVME16x_NET) += 82596.o obj-$(CONFIG_BVME6000_NET) += 82596.o obj-$(CONFIG_SC92031) += sc92031.o diff --git a/drivers/net/acenic.c b/drivers/net/acenic.c index 04382f979c9..b78a4e5ceeb 100644 --- a/drivers/net/acenic.c +++ b/drivers/net/acenic.c @@ -159,10 +159,6 @@ static struct pci_device_id acenic_pci_tbl[] = { }; MODULE_DEVICE_TABLE(pci, acenic_pci_tbl); -#ifndef SET_NETDEV_DEV -#define SET_NETDEV_DEV(net, pdev) do{} while(0) -#endif - #define ace_sync_irq(irq) synchronize_irq(irq) #ifndef offset_in_page diff --git a/drivers/net/arm/Kconfig b/drivers/net/arm/Kconfig index 678e4f48d36..5bf2d33887a 100644 --- a/drivers/net/arm/Kconfig +++ b/drivers/net/arm/Kconfig @@ -4,7 +4,7 @@ # config ARM_AM79C961A bool "ARM EBSA110 AM79C961A support" - depends on NET_ETHERNET && ARM && ARCH_EBSA110 + depends on ARM && ARCH_EBSA110 select CRC32 help If you wish to compile a kernel for the EBSA-110, then you should @@ -12,21 +12,21 @@ config ARM_AM79C961A config ARM_ETHER1 tristate "Acorn Ether1 support" - depends on NET_ETHERNET && ARM && ARCH_ACORN + depends on ARM && ARCH_ACORN help If you have an Acorn system with one of these (AKA25) network cards, you should say Y to this option if you wish to use it with Linux. config ARM_ETHER3 tristate "Acorn/ANT Ether3 support" - depends on NET_ETHERNET && ARM && ARCH_ACORN + depends on ARM && ARCH_ACORN help If you have an Acorn system with one of these network cards, you should say Y to this option if you wish to use it with Linux. config ARM_ETHERH tristate "I-cubed EtherH/ANT EtherM support" - depends on NET_ETHERNET && ARM && ARCH_ACORN + depends on ARM && ARCH_ACORN select CRC32 help If you have an Acorn system with one of these network cards, you @@ -34,7 +34,7 @@ config ARM_ETHERH config ARM_AT91_ETHER tristate "AT91RM9200 Ethernet support" - depends on NET_ETHERNET && ARM && ARCH_AT91RM9200 + depends on ARM && ARCH_AT91RM9200 select MII help If you wish to compile a kernel for the AT91RM9200 and enable @@ -42,7 +42,7 @@ config ARM_AT91_ETHER config EP93XX_ETH tristate "EP93xx Ethernet support" - depends on NET_ETHERNET && ARM && ARCH_EP93XX + depends on ARM && ARCH_EP93XX help This is a driver for the ethernet hardware included in EP93xx CPUs. Say Y if you are building a kernel for EP93xx based devices. diff --git a/drivers/net/b44.c b/drivers/net/b44.c index 879a2fff474..96fb0ec905a 100644 --- a/drivers/net/b44.c +++ b/drivers/net/b44.c @@ -15,6 +15,7 @@ #include <linux/ethtool.h> #include <linux/mii.h> #include <linux/if_ether.h> +#include <linux/if_vlan.h> #include <linux/etherdevice.h> #include <linux/pci.h> #include <linux/delay.h> @@ -68,8 +69,8 @@ (BP)->tx_cons - (BP)->tx_prod - TX_RING_GAP(BP)) #define NEXT_TX(N) (((N) + 1) & (B44_TX_RING_SIZE - 1)) -#define RX_PKT_BUF_SZ (1536 + bp->rx_offset + 64) -#define TX_PKT_BUF_SZ (B44_MAX_MTU + ETH_HLEN + 8) +#define RX_PKT_OFFSET 30 +#define RX_PKT_BUF_SZ (1536 + RX_PKT_OFFSET + 64) /* minimum number of free TX descriptors required to wake up TX process */ #define B44_TX_WAKEUP_THRESH (B44_TX_RING_SIZE / 4) @@ -599,8 +600,7 @@ static void b44_timer(unsigned long __opaque) spin_unlock_irq(&bp->lock); - bp->timer.expires = jiffies + HZ; - add_timer(&bp->timer); + mod_timer(&bp->timer, round_jiffies(jiffies + HZ)); } static void b44_tx(struct b44 *bp) @@ -653,7 +653,7 @@ static int b44_alloc_rx_skb(struct b44 *bp, int src_idx, u32 dest_idx_unmasked) src_map = &bp->rx_buffers[src_idx]; dest_idx = dest_idx_unmasked & (B44_RX_RING_SIZE - 1); map = &bp->rx_buffers[dest_idx]; - skb = dev_alloc_skb(RX_PKT_BUF_SZ); + skb = netdev_alloc_skb(bp->dev, RX_PKT_BUF_SZ); if (skb == NULL) return -ENOMEM; @@ -669,7 +669,7 @@ static int b44_alloc_rx_skb(struct b44 *bp, int src_idx, u32 dest_idx_unmasked) if (!dma_mapping_error(mapping)) pci_unmap_single(bp->pdev, mapping, RX_PKT_BUF_SZ,PCI_DMA_FROMDEVICE); dev_kfree_skb_any(skb); - skb = __dev_alloc_skb(RX_PKT_BUF_SZ,GFP_DMA); + skb = __netdev_alloc_skb(bp->dev, RX_PKT_BUF_SZ, GFP_ATOMIC|GFP_DMA); if (skb == NULL) return -ENOMEM; mapping = pci_map_single(bp->pdev, skb->data, @@ -684,11 +684,9 @@ static int b44_alloc_rx_skb(struct b44 *bp, int src_idx, u32 dest_idx_unmasked) } } - skb->dev = bp->dev; - skb_reserve(skb, bp->rx_offset); + rh = (struct rx_header *) skb->data; + skb_reserve(skb, RX_PKT_OFFSET); - rh = (struct rx_header *) - (skb->data - bp->rx_offset); rh->len = 0; rh->flags = 0; @@ -698,13 +696,13 @@ static int b44_alloc_rx_skb(struct b44 *bp, int src_idx, u32 dest_idx_unmasked) if (src_map != NULL) src_map->skb = NULL; - ctrl = (DESC_CTRL_LEN & (RX_PKT_BUF_SZ - bp->rx_offset)); + ctrl = (DESC_CTRL_LEN & (RX_PKT_BUF_SZ - RX_PKT_OFFSET)); if (dest_idx == (B44_RX_RING_SIZE - 1)) ctrl |= DESC_CTRL_EOT; dp = &bp->rx_ring[dest_idx]; dp->ctrl = cpu_to_le32(ctrl); - dp->addr = cpu_to_le32((u32) mapping + bp->rx_offset + bp->dma_offset); + dp->addr = cpu_to_le32((u32) mapping + RX_PKT_OFFSET + bp->dma_offset); if (bp->flags & B44_FLAG_RX_RING_HACK) b44_sync_dma_desc_for_device(bp->pdev, bp->rx_ring_dma, @@ -783,7 +781,7 @@ static int b44_rx(struct b44 *bp, int budget) PCI_DMA_FROMDEVICE); rh = (struct rx_header *) skb->data; len = le16_to_cpu(rh->len); - if ((len > (RX_PKT_BUF_SZ - bp->rx_offset)) || + if ((len > (RX_PKT_BUF_SZ - RX_PKT_OFFSET)) || (rh->flags & cpu_to_le16(RX_FLAG_ERRORS))) { drop_it: b44_recycle_rx(bp, cons, bp->rx_prod); @@ -815,8 +813,8 @@ static int b44_rx(struct b44 *bp, int budget) pci_unmap_single(bp->pdev, map, skb_size, PCI_DMA_FROMDEVICE); /* Leave out rx_header */ - skb_put(skb, len+bp->rx_offset); - skb_pull(skb,bp->rx_offset); + skb_put(skb, len + RX_PKT_OFFSET); + skb_pull(skb, RX_PKT_OFFSET); } else { struct sk_buff *copy_skb; @@ -828,7 +826,7 @@ static int b44_rx(struct b44 *bp, int budget) skb_reserve(copy_skb, 2); skb_put(copy_skb, len); /* DMA sync done above, copy just the actual packet */ - skb_copy_from_linear_data_offset(skb, bp->rx_offset, + skb_copy_from_linear_data_offset(skb, RX_PKT_OFFSET, copy_skb->data, len); skb = copy_skb; } @@ -969,7 +967,6 @@ static void b44_tx_timeout(struct net_device *dev) static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev) { struct b44 *bp = netdev_priv(dev); - struct sk_buff *bounce_skb; int rc = NETDEV_TX_OK; dma_addr_t mapping; u32 len, entry, ctrl; @@ -987,12 +984,13 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev) mapping = pci_map_single(bp->pdev, skb->data, len, PCI_DMA_TODEVICE); if (dma_mapping_error(mapping) || mapping + len > DMA_30BIT_MASK) { + struct sk_buff *bounce_skb; + /* Chip can't handle DMA to/from >1GB, use bounce buffer */ if (!dma_mapping_error(mapping)) pci_unmap_single(bp->pdev, mapping, len, PCI_DMA_TODEVICE); - bounce_skb = __dev_alloc_skb(TX_PKT_BUF_SZ, - GFP_ATOMIC|GFP_DMA); + bounce_skb = __dev_alloc_skb(len, GFP_ATOMIC | GFP_DMA); if (!bounce_skb) goto err_out; @@ -1001,13 +999,12 @@ static int b44_start_xmit(struct sk_buff *skb, struct net_device *dev) if (dma_mapping_error(mapping) || mapping + len > DMA_30BIT_MASK) { if (!dma_mapping_error(mapping)) pci_unmap_single(bp->pdev, mapping, - len, PCI_DMA_TODEVICE); + len, PCI_DMA_TODEVICE); dev_kfree_skb_any(bounce_skb); goto err_out; } - skb_copy_from_linear_data(skb, skb_put(bounce_skb, len), - skb->len); + skb_copy_from_linear_data(skb, skb_put(bounce_skb, len), len); dev_kfree_skb_any(skb); skb = bounce_skb; } @@ -1396,12 +1393,12 @@ static void b44_init_hw(struct b44 *bp, int reset_kind) bw32(bp, B44_TX_WMARK, 56); /* XXX magic */ if (reset_kind == B44_PARTIAL_RESET) { bw32(bp, B44_DMARX_CTRL, (DMARX_CTRL_ENABLE | - (bp->rx_offset << DMARX_CTRL_ROSHIFT))); + (RX_PKT_OFFSET << DMARX_CTRL_ROSHIFT))); } else { bw32(bp, B44_DMATX_CTRL, DMATX_CTRL_ENABLE); bw32(bp, B44_DMATX_ADDR, bp->tx_ring_dma + bp->dma_offset); bw32(bp, B44_DMARX_CTRL, (DMARX_CTRL_ENABLE | - (bp->rx_offset << DMARX_CTRL_ROSHIFT))); + (RX_PKT_OFFSET << DMARX_CTRL_ROSHIFT))); bw32(bp, B44_DMARX_ADDR, bp->rx_ring_dma + bp->dma_offset); bw32(bp, B44_DMARX_PTR, bp->rx_pending); @@ -2093,11 +2090,6 @@ static int __devinit b44_get_invariants(struct b44 *bp) bp->phy_addr = eeprom[90] & 0x1f; - /* With this, plus the rx_header prepended to the data by the - * hardware, we'll land the ethernet header on a 2-byte boundary. - */ - bp->rx_offset = 30; - bp->imask = IMASK_DEF; bp->core_unit = ssb_core_unit(bp); @@ -2348,11 +2340,11 @@ static int b44_resume(struct pci_dev *pdev) netif_device_attach(bp->dev); spin_unlock_irq(&bp->lock); - bp->timer.expires = jiffies + HZ; - add_timer(&bp->timer); - b44_enable_ints(bp); netif_wake_queue(dev); + + mod_timer(&bp->timer, jiffies + 1); + return 0; } diff --git a/drivers/net/b44.h b/drivers/net/b44.h index 18fc1333662..e537e63f292 100644 --- a/drivers/net/b44.h +++ b/drivers/net/b44.h @@ -443,8 +443,6 @@ struct b44 { #define B44_FLAG_TX_RING_HACK 0x40000000 #define B44_FLAG_WOL_ENABLE 0x80000000 - u32 rx_offset; - u32 msg_enable; struct timer_list timer; diff --git a/drivers/net/cxgb3/adapter.h b/drivers/net/cxgb3/adapter.h index 80c3d8f268a..ab72563b81e 100644 --- a/drivers/net/cxgb3/adapter.h +++ b/drivers/net/cxgb3/adapter.h @@ -71,27 +71,29 @@ enum { /* adapter flags */ QUEUES_BOUND = (1 << 3), }; +struct fl_pg_chunk { + struct page *page; + void *va; + unsigned int offset; +}; + struct rx_desc; struct rx_sw_desc; -struct sge_fl_page { - struct skb_frag_struct frag; - unsigned char *va; -}; - -struct sge_fl { /* SGE per free-buffer list state */ - unsigned int buf_size; /* size of each Rx buffer */ - unsigned int credits; /* # of available Rx buffers */ - unsigned int size; /* capacity of free list */ - unsigned int cidx; /* consumer index */ - unsigned int pidx; /* producer index */ - unsigned int gen; /* free list generation */ - unsigned int cntxt_id; /* SGE context id for the free list */ - struct sge_fl_page page; - struct rx_desc *desc; /* address of HW Rx descriptor ring */ - struct rx_sw_desc *sdesc; /* address of SW Rx descriptor ring */ - dma_addr_t phys_addr; /* physical address of HW ring start */ - unsigned long empty; /* # of times queue ran out of buffers */ +struct sge_fl { /* SGE per free-buffer list state */ + unsigned int buf_size; /* size of each Rx buffer */ + unsigned int credits; /* # of available Rx buffers */ + unsigned int size; /* capacity of free list */ + unsigned int cidx; /* consumer index */ + unsigned int pidx; /* producer index */ + unsigned int gen; /* free list generation */ + struct fl_pg_chunk pg_chunk;/* page chunk cache */ + unsigned int use_pages; /* whether FL uses pages or sk_buffs */ + struct rx_desc *desc; /* address of HW Rx descriptor ring */ + struct rx_sw_desc *sdesc; /* address of SW Rx descriptor ring */ + dma_addr_t phys_addr; /* physical address of HW ring start */ + unsigned int cntxt_id; /* SGE context id for the free list */ + unsigned long empty; /* # of times queue ran out of buffers */ unsigned long alloc_failed; /* # of times buffer allocation failed */ }; diff --git a/drivers/net/cxgb3/common.h b/drivers/net/cxgb3/common.h index 8d137963369..16378004507 100644 --- a/drivers/net/cxgb3/common.h +++ b/drivers/net/cxgb3/common.h @@ -101,6 +101,7 @@ enum { TCB_SIZE = 128, /* TCB size */ NMTUS = 16, /* size of MTU table */ NCCTRL_WIN = 32, /* # of congestion control windows */ + PROTO_SRAM_LINES = 128, /* size of TP sram */ }; #define MAX_RX_COALESCING_LEN 16224U @@ -124,6 +125,30 @@ enum { /* adapter interrupt-maintained statistics */ }; enum { + TP_VERSION_MAJOR = 1, + TP_VERSION_MINOR = 0, + TP_VERSION_MICRO = 44 +}; + +#define S_TP_VERSION_MAJOR 16 +#define M_TP_VERSION_MAJOR 0xFF +#define V_TP_VERSION_MAJOR(x) ((x) << S_TP_VERSION_MAJOR) +#define G_TP_VERSION_MAJOR(x) \ + (((x) >> S_TP_VERSION_MAJOR) & M_TP_VERSION_MAJOR) + +#define S_TP_VERSION_MINOR 8 +#define M_TP_VERSION_MINOR 0xFF +#define V_TP_VERSION_MINOR(x) ((x) << S_TP_VERSION_MINOR) +#define G_TP_VERSION_MINOR(x) \ + (((x) >> S_TP_VERSION_MINOR) & M_TP_VERSION_MINOR) + +#define S_TP_VERSION_MICRO 0 +#define M_TP_VERSION_MICRO 0xFF +#define V_TP_VERSION_MICRO(x) ((x) << S_TP_VERSION_MICRO) +#define G_TP_VERSION_MICRO(x) \ + (((x) >> S_TP_VERSION_MICRO) & M_TP_VERSION_MICRO) + +enum { SGE_QSETS = 8, /* # of SGE Tx/Rx/RspQ sets */ SGE_RXQ_PER_SET = 2, /* # of Rx queues per set */ SGE_TXQ_PER_SET = 3 /* # of Tx queues per set */ @@ -654,6 +679,9 @@ const struct adapter_info *t3_get_adapter_info(unsigned int board_id); int t3_seeprom_read(struct adapter *adapter, u32 addr, u32 *data); int t3_seeprom_write(struct adapter *adapter, u32 addr, u32 data); int t3_seeprom_wp(struct adapter *adapter, int enable); +int t3_check_tpsram_version(struct adapter *adapter); +int t3_check_tpsram(struct adapter *adapter, u8 *tp_ram, unsigned int size); +int t3_set_proto_sram(struct adapter *adap, u8 *data); int t3_read_flash(struct adapter *adapter, unsigned int addr, unsigned int nwords, u32 *data, int byte_oriented); int t3_load_fw(struct adapter *adapter, const u8 * fw_data, unsigned int size); diff --git a/drivers/net/cxgb3/cxgb3_main.c b/drivers/net/cxgb3/cxgb3_main.c index d8a1f5452c5..15defe4c4f0 100644 --- a/drivers/net/cxgb3/cxgb3_main.c +++ b/drivers/net/cxgb3/cxgb3_main.c @@ -2088,6 +2088,42 @@ static void cxgb_netpoll(struct net_device *dev) } #endif +#define TPSRAM_NAME "t3%c_protocol_sram-%d.%d.%d.bin" +int update_tpsram(struct adapter *adap) +{ + const struct firmware *tpsram; + char buf[64]; + struct device *dev = &adap->pdev->dev; + int ret; + char rev; + + rev = adap->params.rev == T3_REV_B2 ? 'b' : 'a'; + + snprintf(buf, sizeof(buf), TPSRAM_NAME, rev, + TP_VERSION_MAJOR, TP_VERSION_MINOR, TP_VERSION_MICRO); + + ret = request_firmware(&tpsram, buf, dev); + if (ret < 0) { + dev_err(dev, "could not load TP SRAM: unable to load %s\n", + buf); + return ret; + } + + ret = t3_check_tpsram(adap, tpsram->data, tpsram->size); + if (ret) + goto release_tpsram; + + ret = t3_set_proto_sram(adap, tpsram->data); + if (ret) + dev_err(dev, "loading protocol SRAM failed\n"); + +release_tpsram: + release_firmware(tpsram); + + return ret; +} + + /* * Periodic accumulation of MAC statistics. */ @@ -2437,6 +2473,13 @@ static int __devinit init_one(struct pci_dev *pdev, goto out_free_dev; } + err = t3_check_tpsram_version(adapter); + if (err == -EINVAL) + err = update_tpsram(adapter); + + if (err) + goto out_free_dev; + /* * The card is now ready to go. If any errors occur during device * registration we do not fail the whole card but rather proceed only diff --git a/drivers/net/cxgb3/regs.h b/drivers/net/cxgb3/regs.h index 020859c855d..aa80313c922 100644 --- a/drivers/net/cxgb3/regs.h +++ b/drivers/net/cxgb3/regs.h @@ -1160,6 +1160,8 @@ #define A_TP_MOD_CHANNEL_WEIGHT 0x434 +#define A_TP_MOD_RATE_LIMIT 0x438 + #define A_TP_PIO_ADDR 0x440 #define A_TP_PIO_DATA 0x444 @@ -1214,6 +1216,15 @@ #define G_TXDROPCNTCH0RCVD(x) (((x) >> S_TXDROPCNTCH0RCVD) & \ M_TXDROPCNTCH0RCVD) +#define A_TP_PROXY_FLOW_CNTL 0x4b0 + +#define A_TP_EMBED_OP_FIELD0 0x4e8 +#define A_TP_EMBED_OP_FIELD1 0x4ec +#define A_TP_EMBED_OP_FIELD2 0x4f0 +#define A_TP_EMBED_OP_FIELD3 0x4f4 +#define A_TP_EMBED_OP_FIELD4 0x4f8 +#define A_TP_EMBED_OP_FIELD5 0x4fc + #define A_ULPRX_CTL 0x500 #define S_ROUND_ROBIN 4 diff --git a/drivers/net/cxgb3/sge.c b/drivers/net/cxgb3/sge.c index a60ec4d4707..a2cfd68ac75 100644 --- a/drivers/net/cxgb3/sge.c +++ b/drivers/net/cxgb3/sge.c @@ -46,23 +46,16 @@ #define SGE_RX_SM_BUF_SIZE 1536 -/* - * If USE_RX_PAGE is defined, the small freelist populated with (partial) - * pages instead of skbs. Pages are carved up into RX_PAGE_SIZE chunks (must - * be a multiple of the host page size). - */ -#define USE_RX_PAGE -#define RX_PAGE_SIZE 2048 - -/* - * skb freelist packets are copied into a new skb (and the freelist one is - * reused) if their len is <= - */ #define SGE_RX_COPY_THRES 256 +#define SGE_RX_PULL_LEN 128 /* - * Minimum number of freelist entries before we start dropping TUNNEL frames. + * Page chunk size for FL0 buffers if FL0 is to be populated with page chunks. + * It must be a divisor of PAGE_SIZE. If set to 0 FL0 will use sk_buffs + * directly. */ +#define FL0_PG_CHUNK_SIZE 2048 + #define SGE_RX_DROP_THRES 16 /* @@ -100,12 +93,12 @@ struct tx_sw_desc { /* SW state per Tx descriptor */ struct sk_buff *skb; }; -struct rx_sw_desc { /* SW state per Rx descriptor */ +struct rx_sw_desc { /* SW state per Rx descriptor */ union { struct sk_buff *skb; - struct sge_fl_page page; - } t; - DECLARE_PCI_UNMAP_ADDR(dma_addr); + struct fl_pg_chunk pg_chunk; + }; + DECLARE_PCI_UNMAP_ADDR(dma_addr); }; struct rsp_desc { /* response queue descriptor */ @@ -351,27 +344,26 @@ static void free_rx_bufs(struct pci_dev *pdev, struct sge_fl *q) pci_unmap_single(pdev, pci_unmap_addr(d, dma_addr), q->buf_size, PCI_DMA_FROMDEVICE); - - if (q->buf_size != RX_PAGE_SIZE) { - kfree_skb(d->t.skb); - d->t.skb = NULL; + if (q->use_pages) { + put_page(d->pg_chunk.page); + d->pg_chunk.page = NULL; } else { - if (d->t.page.frag.page) - put_page(d->t.page.frag.page); - d->t.page.frag.page = NULL; + kfree_skb(d->skb); + d->skb = NULL; } if (++cidx == q->size) cidx = 0; } - if (q->page.frag.page) - put_page(q->page.frag.page); - q->page.frag.page = NULL; + if (q->pg_chunk.page) { + __free_page(q->pg_chunk.page); + q->pg_chunk.page = NULL; + } } /** * add_one_rx_buf - add a packet buffer to a free-buffer list - * @va: va of the buffer to add + * @va: buffer start VA * @len: the buffer length * @d: the HW Rx descriptor to write * @sd: the SW Rx descriptor to write @@ -381,7 +373,7 @@ static void free_rx_bufs(struct pci_dev *pdev, struct sge_fl *q) * Add a buffer of the given length to the supplied HW and SW Rx * descriptors. */ -static inline void add_one_rx_buf(unsigned char *va, unsigned int len, +static inline void add_one_rx_buf(void *va, unsigned int len, struct rx_desc *d, struct rx_sw_desc *sd, unsigned int gen, struct pci_dev *pdev) { @@ -397,6 +389,27 @@ static inline void add_one_rx_buf(unsigned char *va, unsigned int len, d->gen2 = cpu_to_be32(V_FLD_GEN2(gen)); } +static int alloc_pg_chunk(struct sge_fl *q, struct rx_sw_desc *sd, gfp_t gfp) +{ + if (!q->pg_chunk.page) { + q->pg_chunk.page = alloc_page(gfp); + if (unlikely(!q->pg_chunk.page)) + return -ENOMEM; + q->pg_chunk.va = page_address(q->pg_chunk.page); + q->pg_chunk.offset = 0; + } + sd->pg_chunk = q->pg_chunk; + + q->pg_chunk.offset += q->buf_size; + if (q->pg_chunk.offset == PAGE_SIZE) + q->pg_chunk.page = NULL; + else { + q->pg_chunk.va += q->buf_size; + get_page(q->pg_chunk.page); + } + return 0; +} + /** * refill_fl - refill an SGE free-buffer list * @adapter: the adapter @@ -410,49 +423,29 @@ static inline void add_one_rx_buf(unsigned char *va, unsigned int len, */ static void refill_fl(struct adapter *adap, struct sge_fl *q, int n, gfp_t gfp) { + void *buf_start; struct rx_sw_desc *sd = &q->sdesc[q->pidx]; struct rx_desc *d = &q->desc[q->pidx]; - struct sge_fl_page *p = &q->page; while (n--) { - unsigned char *va; - - if (unlikely(q->buf_size != RX_PAGE_SIZE)) { - struct sk_buff *skb = alloc_skb(q->buf_size, gfp); - - if (!skb) { - q->alloc_failed++; + if (q->use_pages) { + if (unlikely(alloc_pg_chunk(q, sd, gfp))) { +nomem: q->alloc_failed++; break; } - va = skb->data; - sd->t.skb = skb; + buf_start = sd->pg_chunk.va; } else { - if (!p->frag.page) { - p->frag.page = alloc_pages(gfp, 0); - if (unlikely(!p->frag.page)) { - q->alloc_failed++; - break; - } else { - p->frag.size = RX_PAGE_SIZE; - p->frag.page_offset = 0; - p->va = page_address(p->frag.page); - } - } + struct sk_buff *skb = alloc_skb(q->buf_size, gfp); - memcpy(&sd->t, p, sizeof(*p)); - va = p->va; + if (!skb) + goto nomem; - p->frag.page_offset += RX_PAGE_SIZE; - BUG_ON(p->frag.page_offset > PAGE_SIZE); - p->va += RX_PAGE_SIZE; - if (p->frag.page_offset == PAGE_SIZE) - p->frag.page = NULL; - else - get_page(p->frag.page); + sd->skb = skb; + buf_start = skb->data; } - add_one_rx_buf(va, q->buf_size, d, sd, q->gen, adap->pdev); - + add_one_rx_buf(buf_start, q->buf_size, d, sd, q->gen, + adap->pdev); d++; sd++; if (++q->pidx == q->size) { @@ -487,7 +480,7 @@ static void recycle_rx_buf(struct adapter *adap, struct sge_fl *q, struct rx_desc *from = &q->desc[idx]; struct rx_desc *to = &q->desc[q->pidx]; - memcpy(&q->sdesc[q->pidx], &q->sdesc[idx], sizeof(struct rx_sw_desc)); + q->sdesc[q->pidx] = q->sdesc[idx]; to->addr_lo = from->addr_lo; /* already big endian */ to->addr_hi = from->addr_hi; /* likewise */ wmb(); @@ -650,6 +643,132 @@ static inline unsigned int flits_to_desc(unsigned int n) } /** + * get_packet - return the next ingress packet buffer from a free list + * @adap: the adapter that received the packet + * @fl: the SGE free list holding the packet + * @len: the packet length including any SGE padding + * @drop_thres: # of remaining buffers before we start dropping packets + * + * Get the next packet from a free list and complete setup of the + * sk_buff. If the packet is small we make a copy and recycle the + * original buffer, otherwise we use the original buffer itself. If a + * positive drop threshold is supplied packets are dropped and their + * buffers recycled if (a) the number of remaining buffers is under the + * threshold and the packet is too big to copy, or (b) the packet should + * be copied but there is no memory for the copy. + */ +static struct sk_buff *get_packet(struct adapter *adap, struct sge_fl *fl, + unsigned int len, unsigned int drop_thres) +{ + struct sk_buff *skb = NULL; + struct rx_sw_desc *sd = &fl->sdesc[fl->cidx]; + + prefetch(sd->skb->data); + fl->credits--; + + if (len <= SGE_RX_COPY_THRES) { + skb = alloc_skb(len, GFP_ATOMIC); + if (likely(skb != NULL)) { + __skb_put(skb, len); + pci_dma_sync_single_for_cpu(adap->pdev, + pci_unmap_addr(sd, dma_addr), len, + PCI_DMA_FROMDEVICE); + memcpy(skb->data, sd->skb->data, len); + pci_dma_sync_single_for_device(adap->pdev, + pci_unmap_addr(sd, dma_addr), len, + PCI_DMA_FROMDEVICE); + } else if (!drop_thres) + goto use_orig_buf; +recycle: + recycle_rx_buf(adap, fl, fl->cidx); + return skb; + } + + if (unlikely(fl->credits < drop_thres)) + goto recycle; + +use_orig_buf: + pci_unmap_single(adap->pdev, pci_unmap_addr(sd, dma_addr), + fl->buf_size, PCI_DMA_FROMDEVICE); + skb = sd->skb; + skb_put(skb, len); + __refill_fl(adap, fl); + return skb; +} + +/** + * get_packet_pg - return the next ingress packet buffer from a free list + * @adap: the adapter that received the packet + * @fl: the SGE free list holding the packet + * @len: the packet length including any SGE padding + * @drop_thres: # of remaining buffers before we start dropping packets + * + * Get the next packet from a free list populated with page chunks. + * If the packet is small we make a copy and recycle the original buffer, + * otherwise we attach the original buffer as a page fragment to a fresh + * sk_buff. If a positive drop threshold is supplied packets are dropped + * and their buffers recycled if (a) the number of remaining buffers is + * under the threshold and the packet is too big to copy, or (b) there's + * no system memory. + * + * Note: this function is similar to @get_packet but deals with Rx buffers + * that are page chunks rather than sk_buffs. + */ +static struct sk_buff *get_packet_pg(struct adapter *adap, struct sge_fl *fl, + unsigned int len, unsigned int drop_thres) +{ + struct sk_buff *skb = NULL; + struct rx_sw_desc *sd = &fl->sdesc[fl->cidx]; + + if (len <= SGE_RX_COPY_THRES) { + skb = alloc_skb(len, GFP_ATOMIC); + if (likely(skb != NULL)) { + __skb_put(skb, len); + pci_dma_sync_single_for_cpu(adap->pdev, + pci_unmap_addr(sd, dma_addr), len, + PCI_DMA_FROMDEVICE); + memcpy(skb->data, sd->pg_chunk.va, len); + pci_dma_sync_single_for_device(adap->pdev, + pci_unmap_addr(sd, dma_addr), len, + PCI_DMA_FROMDEVICE); + } else if (!drop_thres) + return NULL; +recycle: + fl->credits--; + recycle_rx_buf(adap, fl, fl->cidx); + return skb; + } + + if (unlikely(fl->credits <= drop_thres)) + goto recycle; + + skb = alloc_skb(SGE_RX_PULL_LEN, GFP_ATOMIC); + if (unlikely(!skb)) { + if (!drop_thres) + return NULL; + goto recycle; + } + + pci_unmap_single(adap->pdev, pci_unmap_addr(sd, dma_addr), + fl->buf_size, PCI_DMA_FROMDEVICE); + __skb_put(skb, SGE_RX_PULL_LEN); + memcpy(skb->data, sd->pg_chunk.va, SGE_RX_PULL_LEN); + skb_fill_page_desc(skb, 0, sd->pg_chunk.page, + sd->pg_chunk.offset + SGE_RX_PULL_LEN, + len - SGE_RX_PULL_LEN); + skb->len = len; + skb->data_len = len - SGE_RX_PULL_LEN; + skb->truesize += skb->data_len; + + fl->credits--; + /* + * We do not refill FLs here, we let the caller do it to overlap a + * prefetch. + */ + return skb; +} + +/** * get_imm_packet - return the next ingress packet buffer from a response * @resp: the response descriptor containing the packet data * @@ -1715,85 +1834,6 @@ static void rx_eth(struct adapter *adap, struct sge_rspq *rq, netif_rx(skb); } -#define SKB_DATA_SIZE 128 - -static void skb_data_init(struct sk_buff *skb, struct sge_fl_page *p, - unsigned int len) -{ - skb->len = len; - if (len <= SKB_DATA_SIZE) { - skb_copy_to_linear_data(skb, p->va, len); - skb->tail += len; - put_page(p->frag.page); - } else { - skb_copy_to_linear_data(skb, p->va, SKB_DATA_SIZE); - skb_shinfo(skb)->frags[0].page = p->frag.page; - skb_shinfo(skb)->frags[0].page_offset = - p->frag.page_offset + SKB_DATA_SIZE; - skb_shinfo(skb)->frags[0].size = len - SKB_DATA_SIZE; - skb_shinfo(skb)->nr_frags = 1; - skb->data_len = len - SKB_DATA_SIZE; - skb->tail += SKB_DATA_SIZE; - skb->truesize += skb->data_len; - } -} - -/** -* get_packet - return the next ingress packet buffer from a free list -* @adap: the adapter that received the packet -* @fl: the SGE free list holding the packet -* @len: the packet length including any SGE padding -* @drop_thres: # of remaining buffers before we start dropping packets -* -* Get the next packet from a free list and complete setup of the -* sk_buff. If the packet is small we make a copy and recycle the -* original buffer, otherwise we use the original buffer itself. If a -* positive drop threshold is supplied packets are dropped and their -* buffers recycled if (a) the number of remaining buffers is under the -* threshold and the packet is too big to copy, or (b) the packet should -* be copied but there is no memory for the copy. -*/ -static struct sk_buff *get_packet(struct adapter *adap, struct sge_fl *fl, - unsigned int len, unsigned int drop_thres) -{ - struct sk_buff *skb = NULL; - struct rx_sw_desc *sd = &fl->sdesc[fl->cidx]; - - prefetch(sd->t.skb->data); - - if (len <= SGE_RX_COPY_THRES) { - skb = alloc_skb(len, GFP_ATOMIC); - if (likely(skb != NULL)) { - struct rx_desc *d = &fl->desc[fl->cidx]; - dma_addr_t mapping = - (dma_addr_t)((u64) be32_to_cpu(d->addr_hi) << 32 | - be32_to_cpu(d->addr_lo)); - - __skb_put(skb, len); - pci_dma_sync_single_for_cpu(adap->pdev, mapping, len, - PCI_DMA_FROMDEVICE); - skb_copy_from_linear_data(sd->t.skb, skb->data, len); - pci_dma_sync_single_for_device(adap->pdev, mapping, len, - PCI_DMA_FROMDEVICE); - } else if (!drop_thres) - goto use_orig_buf; -recycle: - recycle_rx_buf(adap, fl, fl->cidx); - return skb; - } - - if (unlikely(fl->credits < drop_thres)) - goto recycle; - -use_orig_buf: - pci_unmap_single(adap->pdev, pci_unmap_addr(sd, dma_addr), - fl->buf_size, PCI_DMA_FROMDEVICE); - skb = sd->t.skb; - skb_put(skb, len); - __refill_fl(adap, fl); - return skb; -} - /** * handle_rsp_cntrl_info - handles control information in a response * @qs: the queue set corresponding to the response @@ -1935,7 +1975,7 @@ static int process_responses(struct adapter *adap, struct sge_qset *qs, } else if (flags & F_RSPD_IMM_DATA_VALID) { skb = get_imm_packet(r); if (unlikely(!skb)) { - no_mem: +no_mem: q->next_holdoff = NOMEM_INTR_DELAY; q->nomem++; /* consume one credit since we tried */ @@ -1945,53 +1985,29 @@ static int process_responses(struct adapter *adap, struct sge_qset *qs, q->imm_data++; ethpad = 0; } else if ((len = ntohl(r->len_cq)) != 0) { - struct sge_fl *fl = - (len & F_RSPD_FLQ) ? &qs->fl[1] : &qs->fl[0]; + struct sge_fl *fl; - if (fl->buf_size == RX_PAGE_SIZE) { - struct rx_sw_desc *sd = &fl->sdesc[fl->cidx]; - struct sge_fl_page *p = &sd->t.page; - - prefetch(p->va); - prefetch(p->va + L1_CACHE_BYTES); + fl = (len & F_RSPD_FLQ) ? &qs->fl[1] : &qs->fl[0]; + if (fl->use_pages) { + void *addr = fl->sdesc[fl->cidx].pg_chunk.va; + prefetch(addr); +#if L1_CACHE_BYTES < 128 + prefetch(addr + L1_CACHE_BYTES); +#endif __refill_fl(adap, fl); - pci_unmap_single(adap->pdev, - pci_unmap_addr(sd, dma_addr), - fl->buf_size, - PCI_DMA_FROMDEVICE); - - if (eth) { - if (unlikely(fl->credits < - SGE_RX_DROP_THRES)) - goto eth_recycle; - - skb = alloc_skb(SKB_DATA_SIZE, - GFP_ATOMIC); - if (unlikely(!skb)) { -eth_recycle: - q->rx_drops++; - recycle_rx_buf(adap, fl, - fl->cidx); - goto eth_done; - } - } else { - skb = alloc_skb(SKB_DATA_SIZE, - GFP_ATOMIC); - if (unlikely(!skb)) - goto no_mem; - } - - skb_data_init(skb, p, G_RSPD_LEN(len)); -eth_done: - fl->credits--; - q->eth_pkts++; - } else { - fl->credits--; + skb = get_packet_pg(adap, fl, G_RSPD_LEN(len), + eth ? SGE_RX_DROP_THRES : 0); + } else skb = get_packet(adap, fl, G_RSPD_LEN(len), eth ? SGE_RX_DROP_THRES : 0); - } + if (unlikely(!skb)) { + if (!eth) + goto no_mem; + q->rx_drops++; + } else if (unlikely(r->rss_hdr.opcode == CPL_TRACE_PKT)) + __skb_pull(skb, 2); if (++fl->cidx == fl->size) fl->cidx = 0; @@ -2016,20 +2032,15 @@ eth_done: q->credits = 0; } - if (skb) { - /* Preserve the RSS info in csum & priority */ - skb->csum = rss_hi; - skb->priority = rss_lo; - + if (likely(skb != NULL)) { if (eth) rx_eth(adap, q, skb, ethpad); else { - if (unlikely(r->rss_hdr.opcode == - CPL_TRACE_PKT)) - __skb_pull(skb, ethpad); - - ngathered = rx_offload(&adap->tdev, q, - skb, offload_skbs, + /* Preserve the RSS info in csum & priority */ + skb->csum = rss_hi; + skb->priority = rss_lo; + ngathered = rx_offload(&adap->tdev, q, skb, + offload_skbs, ngathered); } } @@ -2635,25 +2646,15 @@ int t3_sge_alloc_qset(struct adapter *adapter, unsigned int id, int nports, q->txq[TXQ_ETH].stop_thres = nports * flits_to_desc(sgl_len(MAX_SKB_FRAGS + 1) + 3); - if (!is_offload(adapter)) { -#ifdef USE_RX_PAGE - q->fl[0].buf_size = RX_PAGE_SIZE; +#if FL0_PG_CHUNK_SIZE > 0 + q->fl[0].buf_size = FL0_PG_CHUNK_SIZE; #else - q->fl[0].buf_size = SGE_RX_SM_BUF_SIZE + 2 + - sizeof(struct cpl_rx_pkt); + q->fl[0].buf_size = SGE_RX_SM_BUF_SIZE + sizeof(struct cpl_rx_data); #endif - q->fl[1].buf_size = MAX_FRAME_SIZE + 2 + - sizeof(struct cpl_rx_pkt); - } else { -#ifdef USE_RX_PAGE - q->fl[0].buf_size = RX_PAGE_SIZE; -#else - q->fl[0].buf_size = SGE_RX_SM_BUF_SIZE + - sizeof(struct cpl_rx_data); -#endif - q->fl[1].buf_size = (16 * 1024) - - SKB_DATA_ALIGN(sizeof(struct skb_shared_info)); - } + q->fl[0].use_pages = FL0_PG_CHUNK_SIZE > 0; + q->fl[1].buf_size = is_offload(adapter) ? + (16 * 1024) - SKB_DATA_ALIGN(sizeof(struct skb_shared_info)) : + MAX_FRAME_SIZE + 2 + sizeof(struct cpl_rx_pkt); spin_lock(&adapter->sge.reg_lock); diff --git a/drivers/net/cxgb3/t3_hw.c b/drivers/net/cxgb3/t3_hw.c index fb485d0a43d..dd3149d94ba 100644 --- a/drivers/net/cxgb3/t3_hw.c +++ b/drivers/net/cxgb3/t3_hw.c @@ -847,6 +847,64 @@ static int t3_write_flash(struct adapter *adapter, unsigned int addr, return 0; } +/** + * t3_check_tpsram_version - read the tp sram version + * @adapter: the adapter + * + * Reads the protocol sram version from serial eeprom. + */ +int t3_check_tpsram_version(struct adapter *adapter) +{ + int ret; + u32 vers; + unsigned int major, minor; + + /* Get version loaded in SRAM */ + t3_write_reg(adapter, A_TP_EMBED_OP_FIELD0, 0); + ret = t3_wait_op_done(adapter, A_TP_EMBED_OP_FIELD0, + 1, 1, 5, 1); + if (ret) + return ret; + + vers = t3_read_reg(adapter, A_TP_EMBED_OP_FIELD1); + + major = G_TP_VERSION_MAJOR(vers); + minor = G_TP_VERSION_MINOR(vers); + + if (major == TP_VERSION_MAJOR && minor == TP_VERSION_MINOR) + return 0; + + return -EINVAL; +} + +/** + * t3_check_tpsram - check if provided protocol SRAM + * is compatible with this driver + * @adapter: the adapter + * @tp_sram: the firmware image to write + * @size: image size + * + * Checks if an adapter's tp sram is compatible with the driver. + * Returns 0 if the versions are compatible, a negative error otherwise. + */ +int t3_check_tpsram(struct adapter *adapter, u8 *tp_sram, unsigned int size) +{ + u32 csum; + unsigned int i; + const u32 *p = (const u32 *)tp_sram; + + /* Verify checksum */ + for (csum = 0, i = 0; i < size / sizeof(csum); i++) + csum += ntohl(p[i]); + if (csum != 0xffffffff) { + CH_ERR(adapter, "corrupted protocol SRAM image, checksum %u\n", + csum); + return -EINVAL; + } + + return 0; +} + enum fw_version_type { FW_VERSION_N3, FW_VERSION_T3 @@ -921,7 +979,7 @@ static int t3_flash_erase_sectors(struct adapter *adapter, int start, int end) /* * t3_load_fw - download firmware * @adapter: the adapter - * @fw_data: the firrware image to write + * @fw_data: the firmware image to write * @size: image size * * Write the supplied firmware image to the card's serial flash. @@ -2362,7 +2420,7 @@ static void tp_config(struct adapter *adap, const struct tp_params *p) F_TCPCHECKSUMOFFLOAD | V_IPTTL(64)); t3_write_reg(adap, A_TP_TCP_OPTIONS, V_MTUDEFAULT(576) | F_MTUENABLE | V_WINDOWSCALEMODE(1) | - V_TIMESTAMPSMODE(1) | V_SACKMODE(1) | V_SACKRX(1)); + V_TIMESTAMPSMODE(0) | V_SACKMODE(1) | V_SACKRX(1)); t3_write_reg(adap, A_TP_DACK_CONFIG, V_AUTOSTATE3(1) | V_AUTOSTATE2(1) | V_AUTOSTATE1(0) | V_BYTETHRESHOLD(16384) | V_MSSTHRESHOLD(2) | @@ -2371,16 +2429,18 @@ static void tp_config(struct adapter *adap, const struct tp_params *p) F_IPV6ENABLE | F_NICMODE); t3_write_reg(adap, A_TP_TX_RESOURCE_LIMIT, 0x18141814); t3_write_reg(adap, A_TP_PARA_REG4, 0x5050105); - t3_set_reg_field(adap, A_TP_PARA_REG6, - adap->params.rev > 0 ? F_ENABLEESND : F_T3A_ENABLEESND, - 0); + t3_set_reg_field(adap, A_TP_PARA_REG6, 0, + adap->params.rev > 0 ? F_ENABLEESND : + F_T3A_ENABLEESND); t3_set_reg_field(adap, A_TP_PC_CONFIG, - F_ENABLEEPCMDAFULL | F_ENABLEOCSPIFULL, - F_TXDEFERENABLE | F_HEARBEATDACK | F_TXCONGESTIONMODE | - F_RXCONGESTIONMODE); + F_ENABLEEPCMDAFULL, + F_ENABLEOCSPIFULL |F_TXDEFERENABLE | F_HEARBEATDACK | + F_TXCONGESTIONMODE | F_RXCONGESTIONMODE); t3_set_reg_field(adap, A_TP_PC_CONFIG2, F_CHDRAFULL, 0); - + t3_write_reg(adap, A_TP_PROXY_FLOW_CNTL, 1080); + t3_write_reg(adap, A_TP_PROXY_FLOW_CNTL, 1000); + if (adap->params.rev > 0) { tp_wr_indirect(adap, A_TP_EGRESS_CONFIG, F_REWRITEFORCETOSIZE); t3_set_reg_field(adap, A_TP_PARA_REG3, F_TXPACEAUTO, @@ -2390,9 +2450,10 @@ static void tp_config(struct adapter *adap, const struct tp_params *p) } else t3_set_reg_field(adap, A_TP_PARA_REG3, 0, F_TXPACEFIXED); - t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT1, 0x12121212); - t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT0, 0x12121212); - t3_write_reg(adap, A_TP_MOD_CHANNEL_WEIGHT, 0x1212); + t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT1, 0); + t3_write_reg(adap, A_TP_TX_MOD_QUEUE_WEIGHT0, 0); + t3_write_reg(adap, A_TP_MOD_CHANNEL_WEIGHT, 0); + t3_write_reg(adap, A_TP_MOD_RATE_LIMIT, 0xf2200000); } /* Desired TP timer resolution in usec */ @@ -2468,6 +2529,7 @@ int t3_tp_set_coalescing_size(struct adapter *adap, unsigned int size, int psh) val |= F_RXCOALESCEENABLE; if (psh) val |= F_RXCOALESCEPSHEN; + size = min(MAX_RX_COALESCING_LEN, size); t3_write_reg(adap, A_TP_PARA_REG2, V_RXCOALESCESIZE(size) | V_MAXRXDATA(MAX_RX_COALESCING_LEN)); } @@ -2496,11 +2558,11 @@ static void __devinit init_mtus(unsigned short mtus[]) * it can accomodate max size TCP/IP headers when SACK and timestamps * are enabled and still have at least 8 bytes of payload. */ - mtus[0] = 88; - mtus[1] = 256; - mtus[2] = 512; - mtus[3] = 576; - mtus[4] = 808; + mtus[1] = 88; + mtus[1] = 88; + mtus[2] = 256; + mtus[3] = 512; + mtus[4] = 576; mtus[5] = 1024; mtus[6] = 1280; mtus[7] = 1492; @@ -2682,6 +2744,34 @@ static void ulp_config(struct adapter *adap, const struct tp_params *p) t3_write_reg(adap, A_ULPRX_TDDP_TAGMASK, 0xffffffff); } +/** + * t3_set_proto_sram - set the contents of the protocol sram + * @adapter: the adapter + * @data: the protocol image + * + * Write the contents of the protocol SRAM. + */ +int t3_set_proto_sram(struct adapter *adap, u8 *data) +{ + int i; + u32 *buf = (u32 *)data; + + for (i = 0; i < PROTO_SRAM_LINES; i++) { + t3_write_reg(adap, A_TP_EMBED_OP_FIELD5, cpu_to_be32(*buf++)); + t3_write_reg(adap, A_TP_EMBED_OP_FIELD4, cpu_to_be32(*buf++)); + t3_write_reg(adap, A_TP_EMBED_OP_FIELD3, cpu_to_be32(*buf++)); + t3_write_reg(adap, A_TP_EMBED_OP_FIELD2, cpu_to_be32(*buf++)); + t3_write_reg(adap, A_TP_EMBED_OP_FIELD1, cpu_to_be32(*buf++)); + + t3_write_reg(adap, A_TP_EMBED_OP_FIELD0, i << 1 | 1 << 31); + if (t3_wait_op_done(adap, A_TP_EMBED_OP_FIELD0, 1, 1, 5, 1)) + return -EIO; + } + t3_write_reg(adap, A_TP_EMBED_OP_FIELD0, 0); + + return 0; +} + void t3_config_trace_filter(struct adapter *adapter, const struct trace_params *tp, int filter_index, int invert, int enable) @@ -2802,7 +2892,7 @@ static void init_hw_for_avail_ports(struct adapter *adap, int nports) t3_set_reg_field(adap, A_ULPTX_CONFIG, F_CFG_RR_ARB, 0); t3_write_reg(adap, A_MPS_CFG, F_TPRXPORTEN | F_TPTXPORT0EN | F_PORT0ACTIVE | F_ENFORCEPKT); - t3_write_reg(adap, A_PM1_TX_CFG, 0xc000c000); + t3_write_reg(adap, A_PM1_TX_CFG, 0xffffffff); } else { t3_set_reg_field(adap, A_ULPRX_CTL, 0, F_ROUND_ROBIN); t3_set_reg_field(adap, A_ULPTX_CONFIG, 0, F_CFG_RR_ARB); @@ -3097,7 +3187,7 @@ int t3_init_hw(struct adapter *adapter, u32 fw_params) else t3_set_reg_field(adapter, A_PCIX_CFG, 0, F_CLIDECEN); - t3_write_reg(adapter, A_PM1_RX_CFG, 0xf000f000); + t3_write_reg(adapter, A_PM1_RX_CFG, 0xffffffff); init_hw_for_avail_ports(adapter, adapter->params.nports); t3_sge_init(adapter, &adapter->params.sge); diff --git a/drivers/net/cxgb3/version.h b/drivers/net/cxgb3/version.h index b112317f033..8eddd23a3a5 100644 --- a/drivers/net/cxgb3/version.h +++ b/drivers/net/cxgb3/version.h @@ -39,6 +39,6 @@ /* Firmware version */ #define FW_VERSION_MAJOR 4 -#define FW_VERSION_MINOR 0 +#define FW_VERSION_MINOR 1 #define FW_VERSION_MICRO 0 #endif /* __CHELSIO_VERSION_H */ diff --git a/drivers/net/ehea/ehea.h b/drivers/net/ehea/ehea.h index c0f81b5a30f..abaf3ac9493 100644 --- a/drivers/net/ehea/ehea.h +++ b/drivers/net/ehea/ehea.h @@ -39,7 +39,7 @@ #include <asm/io.h> #define DRV_NAME "ehea" -#define DRV_VERSION "EHEA_0064" +#define DRV_VERSION "EHEA_0065" #define EHEA_MSG_DEFAULT (NETIF_MSG_LINK | NETIF_MSG_TIMER \ | NETIF_MSG_RX_ERR | NETIF_MSG_TX_ERR) @@ -136,10 +136,10 @@ void ehea_dump(void *adr, int len, char *msg); (0xffffffffffffffffULL >> ((64 - (mask)) & 0xffff)) #define EHEA_BMASK_SET(mask, value) \ - ((EHEA_BMASK_MASK(mask) & ((u64)(value))) << EHEA_BMASK_SHIFTPOS(mask)) + ((EHEA_BMASK_MASK(mask) & ((u64)(value))) << EHEA_BMASK_SHIFTPOS(mask)) #define EHEA_BMASK_GET(mask, value) \ - (EHEA_BMASK_MASK(mask) & (((u64)(value)) >> EHEA_BMASK_SHIFTPOS(mask))) + (EHEA_BMASK_MASK(mask) & (((u64)(value)) >> EHEA_BMASK_SHIFTPOS(mask))) /* * Generic ehea page @@ -190,7 +190,7 @@ struct ehea_av; * Queue attributes passed to ehea_create_qp() */ struct ehea_qp_init_attr { - /* input parameter */ + /* input parameter */ u32 qp_token; /* queue token */ u8 low_lat_rq1; u8 signalingtype; /* cqe generation flag */ @@ -212,7 +212,7 @@ struct ehea_qp_init_attr { u64 recv_cq_handle; u64 aff_eq_handle; - /* output parameter */ + /* output parameter */ u32 qp_nr; u16 act_nr_send_wqes; u16 act_nr_rwqes_rq1; @@ -279,12 +279,12 @@ struct ehea_qp { * Completion Queue attributes */ struct ehea_cq_attr { - /* input parameter */ + /* input parameter */ u32 max_nr_of_cqes; u32 cq_token; u64 eq_handle; - /* output parameter */ + /* output parameter */ u32 act_nr_of_cqes; u32 nr_pages; }; diff --git a/drivers/net/ehea/ehea_hw.h b/drivers/net/ehea/ehea_hw.h index 1246757f2c2..1af7ca499ec 100644 --- a/drivers/net/ehea/ehea_hw.h +++ b/drivers/net/ehea/ehea_hw.h @@ -211,34 +211,34 @@ static inline void epa_store_acc(struct h_epa epa, u32 offset, u64 value) } #define epa_store_eq(epa, offset, value)\ - epa_store(epa, EQTEMM_OFFSET(offset), value) + epa_store(epa, EQTEMM_OFFSET(offset), value) #define epa_load_eq(epa, offset)\ - epa_load(epa, EQTEMM_OFFSET(offset)) + epa_load(epa, EQTEMM_OFFSET(offset)) #define epa_store_cq(epa, offset, value)\ - epa_store(epa, CQTEMM_OFFSET(offset), value) + epa_store(epa, CQTEMM_OFFSET(offset), value) #define epa_load_cq(epa, offset)\ - epa_load(epa, CQTEMM_OFFSET(offset)) + epa_load(epa, CQTEMM_OFFSET(offset)) #define epa_store_qp(epa, offset, value)\ - epa_store(epa, QPTEMM_OFFSET(offset), value) + epa_store(epa, QPTEMM_OFFSET(offset), value) #define epa_load_qp(epa, offset)\ - epa_load(epa, QPTEMM_OFFSET(offset)) + epa_load(epa, QPTEMM_OFFSET(offset)) #define epa_store_qped(epa, offset, value)\ - epa_store(epa, QPEDMM_OFFSET(offset), value) + epa_store(epa, QPEDMM_OFFSET(offset), value) #define epa_load_qped(epa, offset)\ - epa_load(epa, QPEDMM_OFFSET(offset)) + epa_load(epa, QPEDMM_OFFSET(offset)) #define epa_store_mrmw(epa, offset, value)\ - epa_store(epa, MRMWMM_OFFSET(offset), value) + epa_store(epa, MRMWMM_OFFSET(offset), value) #define epa_load_mrmw(epa, offset)\ - epa_load(epa, MRMWMM_OFFSET(offset)) + epa_load(epa, MRMWMM_OFFSET(offset)) #define epa_store_base(epa, offset, value)\ - epa_store(epa, HCAGR_OFFSET(offset), value) + epa_store(epa, HCAGR_OFFSET(offset), value) #define epa_load_base(epa, offset)\ - epa_load(epa, HCAGR_OFFSET(offset)) + epa_load(epa, HCAGR_OFFSET(offset)) static inline void ehea_update_sqa(struct ehea_qp *qp, u16 nr_wqes) { diff --git a/drivers/net/ehea/ehea_main.c b/drivers/net/ehea/ehea_main.c index 9e13433a268..bdb52419dbf 100644 --- a/drivers/net/ehea/ehea_main.c +++ b/drivers/net/ehea/ehea_main.c @@ -81,7 +81,7 @@ MODULE_PARM_DESC(use_mcs, " 0:NAPI, 1:Multiple receive queues, Default = 1 "); static int port_name_cnt = 0; static int __devinit ehea_probe_adapter(struct ibmebus_dev *dev, - const struct of_device_id *id); + const struct of_device_id *id); static int __devexit ehea_remove(struct ibmebus_dev *dev); @@ -236,7 +236,7 @@ static int ehea_refill_rq_def(struct ehea_port_res *pr, rwqe = ehea_get_next_rwqe(qp, rq_nr); rwqe->wr_id = EHEA_BMASK_SET(EHEA_WR_ID_TYPE, wqe_type) - | EHEA_BMASK_SET(EHEA_WR_ID_INDEX, index); + | EHEA_BMASK_SET(EHEA_WR_ID_INDEX, index); rwqe->sg_list[0].l_key = pr->recv_mr.lkey; rwqe->sg_list[0].vaddr = (u64)skb->data; rwqe->sg_list[0].len = packet_size; @@ -427,7 +427,7 @@ static struct ehea_cqe *ehea_proc_rwqes(struct net_device *dev, break; } skb_copy_to_linear_data(skb, ((char*)cqe) + 64, - cqe->num_bytes_transfered - 4); + cqe->num_bytes_transfered - 4); ehea_fill_skb(port->netdev, skb, cqe); } else if (rq == 2) { /* RQ2 */ skb = get_skb_by_index(skb_arr_rq2, @@ -618,7 +618,7 @@ static struct ehea_port *ehea_get_port(struct ehea_adapter *adapter, for (i = 0; i < EHEA_MAX_PORTS; i++) if (adapter->port[i]) - if (adapter->port[i]->logical_port_id == logical_port) + if (adapter->port[i]->logical_port_id == logical_port) return adapter->port[i]; return NULL; } @@ -1695,6 +1695,7 @@ static void ehea_xmit2(struct sk_buff *skb, struct net_device *dev, { if (skb->protocol == htons(ETH_P_IP)) { const struct iphdr *iph = ip_hdr(skb); + /* IPv4 */ swqe->tx_control |= EHEA_SWQE_CRC | EHEA_SWQE_IP_CHECKSUM @@ -1705,13 +1706,12 @@ static void ehea_xmit2(struct sk_buff *skb, struct net_device *dev, write_ip_start_end(swqe, skb); if (iph->protocol == IPPROTO_UDP) { - if ((iph->frag_off & IP_MF) || - (iph->frag_off & IP_OFFSET)) + if ((iph->frag_off & IP_MF) + || (iph->frag_off & IP_OFFSET)) /* IP fragment, so don't change cs */ swqe->tx_control &= ~EHEA_SWQE_TCP_CHECKSUM; else write_udp_offset_end(swqe, skb); - } else if (iph->protocol == IPPROTO_TCP) { write_tcp_offset_end(swqe, skb); } @@ -1739,6 +1739,7 @@ static void ehea_xmit3(struct sk_buff *skb, struct net_device *dev, if (skb->protocol == htons(ETH_P_IP)) { const struct iphdr *iph = ip_hdr(skb); + /* IPv4 */ write_ip_start_end(swqe, skb); @@ -1751,8 +1752,8 @@ static void ehea_xmit3(struct sk_buff *skb, struct net_device *dev, write_tcp_offset_end(swqe, skb); } else if (iph->protocol == IPPROTO_UDP) { - if ((iph->frag_off & IP_MF) || - (iph->frag_off & IP_OFFSET)) + if ((iph->frag_off & IP_MF) + || (iph->frag_off & IP_OFFSET)) /* IP fragment, so don't change cs */ swqe->tx_control |= EHEA_SWQE_CRC | EHEA_SWQE_IMM_DATA_PRESENT; @@ -2407,7 +2408,7 @@ static void __devinit logical_port_release(struct device *dev) } static int ehea_driver_sysfs_add(struct device *dev, - struct device_driver *driver) + struct device_driver *driver) { int ret; @@ -2424,7 +2425,7 @@ static int ehea_driver_sysfs_add(struct device *dev, } static void ehea_driver_sysfs_remove(struct device *dev, - struct device_driver *driver) + struct device_driver *driver) { struct device_driver *drv = driver; @@ -2453,7 +2454,7 @@ static struct device *ehea_register_port(struct ehea_port *port, } ret = device_create_file(&port->ofdev.dev, &dev_attr_log_port_id); - if (ret) { + if (ret) { ehea_error("failed to register attributes, ret=%d", ret); goto out_unreg_of_dev; } @@ -2601,6 +2602,7 @@ static int ehea_setup_ports(struct ehea_adapter *adapter) { struct device_node *lhea_dn; struct device_node *eth_dn = NULL; + const u32 *dn_log_port_id; int i = 0; @@ -2608,7 +2610,7 @@ static int ehea_setup_ports(struct ehea_adapter *adapter) while ((eth_dn = of_get_next_child(lhea_dn, eth_dn))) { dn_log_port_id = of_get_property(eth_dn, "ibm,hea-port-no", - NULL); + NULL); if (!dn_log_port_id) { ehea_error("bad device node: eth_dn name=%s", eth_dn->full_name); @@ -2648,7 +2650,7 @@ static struct device_node *ehea_get_eth_dn(struct ehea_adapter *adapter, while ((eth_dn = of_get_next_child(lhea_dn, eth_dn))) { dn_log_port_id = of_get_property(eth_dn, "ibm,hea-port-no", - NULL); + NULL); if (dn_log_port_id) if (*dn_log_port_id == logical_port_id) return eth_dn; @@ -2789,7 +2791,7 @@ static int __devinit ehea_probe_adapter(struct ibmebus_dev *dev, adapter->ebus_dev = dev; adapter_handle = of_get_property(dev->ofdev.node, "ibm,hea-handle", - NULL); + NULL); if (adapter_handle) adapter->handle = *adapter_handle; diff --git a/drivers/net/ehea/ehea_qmr.c b/drivers/net/ehea/ehea_qmr.c index f24a8862977..29eaa46948b 100644 --- a/drivers/net/ehea/ehea_qmr.c +++ b/drivers/net/ehea/ehea_qmr.c @@ -211,7 +211,7 @@ u64 ehea_destroy_cq_res(struct ehea_cq *cq, u64 force) u64 hret; u64 adapter_handle = cq->adapter->handle; - /* deregister all previous registered pages */ + /* deregister all previous registered pages */ hret = ehea_h_free_resource(adapter_handle, cq->fw_handle, force); if (hret != H_SUCCESS) return hret; @@ -362,7 +362,7 @@ int ehea_destroy_eq(struct ehea_eq *eq) if (hret != H_SUCCESS) { ehea_error("destroy EQ failed"); return -EIO; - } + } return 0; } @@ -507,44 +507,44 @@ out_freemem: u64 ehea_destroy_qp_res(struct ehea_qp *qp, u64 force) { - u64 hret; - struct ehea_qp_init_attr *qp_attr = &qp->init_attr; + u64 hret; + struct ehea_qp_init_attr *qp_attr = &qp->init_attr; - ehea_h_disable_and_get_hea(qp->adapter->handle, qp->fw_handle); - hret = ehea_h_free_resource(qp->adapter->handle, qp->fw_handle, force); - if (hret != H_SUCCESS) - return hret; + ehea_h_disable_and_get_hea(qp->adapter->handle, qp->fw_handle); + hret = ehea_h_free_resource(qp->adapter->handle, qp->fw_handle, force); + if (hret != H_SUCCESS) + return hret; - hw_queue_dtor(&qp->hw_squeue); - hw_queue_dtor(&qp->hw_rqueue1); + hw_queue_dtor(&qp->hw_squeue); + hw_queue_dtor(&qp->hw_rqueue1); - if (qp_attr->rq_count > 1) - hw_queue_dtor(&qp->hw_rqueue2); - if (qp_attr->rq_count > 2) - hw_queue_dtor(&qp->hw_rqueue3); - kfree(qp); + if (qp_attr->rq_count > 1) + hw_queue_dtor(&qp->hw_rqueue2); + if (qp_attr->rq_count > 2) + hw_queue_dtor(&qp->hw_rqueue3); + kfree(qp); - return hret; + return hret; } int ehea_destroy_qp(struct ehea_qp *qp) { - u64 hret; - if (!qp) - return 0; + u64 hret; + if (!qp) + return 0; - if ((hret = ehea_destroy_qp_res(qp, NORMAL_FREE)) == H_R_STATE) { - ehea_error_data(qp->adapter, qp->fw_handle); - hret = ehea_destroy_qp_res(qp, FORCE_FREE); - } + if ((hret = ehea_destroy_qp_res(qp, NORMAL_FREE)) == H_R_STATE) { + ehea_error_data(qp->adapter, qp->fw_handle); + hret = ehea_destroy_qp_res(qp, FORCE_FREE); + } - if (hret != H_SUCCESS) { - ehea_error("destroy QP failed"); - return -EIO; - } + if (hret != H_SUCCESS) { + ehea_error("destroy QP failed"); + return -EIO; + } - return 0; + return 0; } int ehea_reg_kernel_mr(struct ehea_adapter *adapter, struct ehea_mr *mr) diff --git a/drivers/net/fec_8xx/Kconfig b/drivers/net/fec_8xx/Kconfig index a84c232395e..afb34ded26e 100644 --- a/drivers/net/fec_8xx/Kconfig +++ b/drivers/net/fec_8xx/Kconfig @@ -1,6 +1,6 @@ config FEC_8XX tristate "Motorola 8xx FEC driver" - depends on NET_ETHERNET && 8xx + depends on 8XX select MII config FEC_8XX_GENERIC_PHY diff --git a/drivers/net/fs_enet/Kconfig b/drivers/net/fs_enet/Kconfig index 6aaee67dd4b..e27ee210b60 100644 --- a/drivers/net/fs_enet/Kconfig +++ b/drivers/net/fs_enet/Kconfig @@ -1,6 +1,6 @@ config FS_ENET tristate "Freescale Ethernet Driver" - depends on NET_ETHERNET && (CPM1 || CPM2) + depends on CPM1 || CPM2 select MII config FS_ENET_HAS_SCC diff --git a/drivers/net/gianfar.c b/drivers/net/gianfar.c index 1b854bf07b0..d7a1a58de76 100644 --- a/drivers/net/gianfar.c +++ b/drivers/net/gianfar.c @@ -130,6 +130,9 @@ static int gfar_remove(struct platform_device *pdev); static void free_skb_resources(struct gfar_private *priv); static void gfar_set_multi(struct net_device *dev); static void gfar_set_hash_for_addr(struct net_device *dev, u8 *addr); +static void gfar_configure_serdes(struct net_device *dev); +extern int gfar_local_mdio_write(struct gfar_mii *regs, int mii_id, int regnum, u16 value); +extern int gfar_local_mdio_read(struct gfar_mii *regs, int mii_id, int regnum); #ifdef CONFIG_GFAR_NAPI static int gfar_poll(struct net_device *dev, int *budget); #endif @@ -451,6 +454,9 @@ static int init_phy(struct net_device *dev) phydev = phy_connect(dev, phy_id, &adjust_link, 0, interface); + if (interface == PHY_INTERFACE_MODE_SGMII) + gfar_configure_serdes(dev); + if (IS_ERR(phydev)) { printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); return PTR_ERR(phydev); @@ -465,6 +471,27 @@ static int init_phy(struct net_device *dev) return 0; } +static void gfar_configure_serdes(struct net_device *dev) +{ + struct gfar_private *priv = netdev_priv(dev); + struct gfar_mii __iomem *regs = + (void __iomem *)&priv->regs->gfar_mii_regs; + + /* Initialise TBI i/f to communicate with serdes (lynx phy) */ + + /* Single clk mode, mii mode off(for aerdes communication) */ + gfar_local_mdio_write(regs, TBIPA_VALUE, MII_TBICON, TBICON_CLK_SELECT); + + /* Supported pause and full-duplex, no half-duplex */ + gfar_local_mdio_write(regs, TBIPA_VALUE, MII_ADVERTISE, + ADVERTISE_1000XFULL | ADVERTISE_1000XPAUSE | + ADVERTISE_1000XPSE_ASYM); + + /* ANEG enable, restart ANEG, full duplex mode, speed[1] set */ + gfar_local_mdio_write(regs, TBIPA_VALUE, MII_BMCR, BMCR_ANENABLE | + BMCR_ANRESTART | BMCR_FULLDPLX | BMCR_SPEED1000); +} + static void init_registers(struct net_device *dev) { struct gfar_private *priv = netdev_priv(dev); diff --git a/drivers/net/gianfar.h b/drivers/net/gianfar.h index 39e9e321fcb..d8e779c102f 100644 --- a/drivers/net/gianfar.h +++ b/drivers/net/gianfar.h @@ -136,6 +136,12 @@ extern const char gfar_driver_version[]; #define MIIMCFG_RESET 0x80000000 #define MIIMIND_BUSY 0x00000001 +/* TBI register addresses */ +#define MII_TBICON 0x11 + +/* TBICON register bit fields */ +#define TBICON_CLK_SELECT 0x0020 + /* MAC register bits */ #define MACCFG1_SOFT_RESET 0x80000000 #define MACCFG1_RESET_RX_MC 0x00080000 diff --git a/drivers/net/gianfar_mii.c b/drivers/net/gianfar_mii.c index bcc6b82f4a3..5dd34a1a7b8 100644 --- a/drivers/net/gianfar_mii.c +++ b/drivers/net/gianfar_mii.c @@ -43,13 +43,18 @@ #include "gianfar.h" #include "gianfar_mii.h" -/* Write value to the PHY at mii_id at register regnum, - * on the bus, waiting until the write is done before returning. - * All PHY configuration is done through the TSEC1 MIIM regs */ -int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value) +/* + * Write value to the PHY at mii_id at register regnum, + * on the bus attached to the local interface, which may be different from the + * generic mdio bus (tied to a single interface), waiting until the write is + * done before returning. This is helpful in programming interfaces like + * the TBI which control interfaces like onchip SERDES and are always tied to + * the local mdio pins, which may not be the same as system mdio bus, used for + * controlling the external PHYs, for example. + */ +int gfar_local_mdio_write(struct gfar_mii *regs, int mii_id, + int regnum, u16 value) { - struct gfar_mii __iomem *regs = (void __iomem *)bus->priv; - /* Set the PHY address and the register address we want to write */ gfar_write(®s->miimadd, (mii_id << 8) | regnum); @@ -63,12 +68,19 @@ int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value) return 0; } -/* Read the bus for PHY at addr mii_id, register regnum, and - * return the value. Clears miimcom first. All PHY - * configuration has to be done through the TSEC1 MIIM regs */ -int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum) +/* + * Read the bus for PHY at addr mii_id, register regnum, and + * return the value. Clears miimcom first. All PHY operation + * done on the bus attached to the local interface, + * which may be different from the generic mdio bus + * This is helpful in programming interfaces like + * the TBI which, inturn, control interfaces like onchip SERDES + * and are always tied to the local mdio pins, which may not be the + * same as system mdio bus, used for controlling the external PHYs, for eg. + */ +int gfar_local_mdio_read(struct gfar_mii *regs, int mii_id, int regnum) + { - struct gfar_mii __iomem *regs = (void __iomem *)bus->priv; u16 value; /* Set the PHY address and the register address we want to read */ @@ -88,6 +100,27 @@ int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum) return value; } +/* Write value to the PHY at mii_id at register regnum, + * on the bus, waiting until the write is done before returning. + * All PHY configuration is done through the TSEC1 MIIM regs */ +int gfar_mdio_write(struct mii_bus *bus, int mii_id, int regnum, u16 value) +{ + struct gfar_mii __iomem *regs = (void __iomem *)bus->priv; + + /* Write to the local MII regs */ + return(gfar_local_mdio_write(regs, mii_id, regnum, value)); +} + +/* Read the bus for PHY at addr mii_id, register regnum, and + * return the value. Clears miimcom first. All PHY + * configuration has to be done through the TSEC1 MIIM regs */ +int gfar_mdio_read(struct mii_bus *bus, int mii_id, int regnum) +{ + struct gfar_mii __iomem *regs = (void __iomem *)bus->priv; + + /* Read the local MII regs */ + return(gfar_local_mdio_read(regs, mii_id, regnum)); +} /* Reset the MIIM registers, and wait for the bus to free */ int gfar_mdio_reset(struct mii_bus *bus) diff --git a/drivers/net/lasi_82596.c b/drivers/net/lasi_82596.c index 741780e14b2..efbae4b8398 100644 --- a/drivers/net/lasi_82596.c +++ b/drivers/net/lasi_82596.c @@ -86,93 +86,36 @@ #include <linux/dma-mapping.h> #include <asm/io.h> -#include <asm/pgtable.h> #include <asm/irq.h> #include <asm/pdc.h> -#include <asm/cache.h> #include <asm/parisc-device.h> #define LASI_82596_DRIVER_VERSION "LASI 82596 driver - Revision: 1.30" -/* DEBUG flags - */ - -#define DEB_INIT 0x0001 -#define DEB_PROBE 0x0002 -#define DEB_SERIOUS 0x0004 -#define DEB_ERRORS 0x0008 -#define DEB_MULTI 0x0010 -#define DEB_TDR 0x0020 -#define DEB_OPEN 0x0040 -#define DEB_RESET 0x0080 -#define DEB_ADDCMD 0x0100 -#define DEB_STATUS 0x0200 -#define DEB_STARTTX 0x0400 -#define DEB_RXADDR 0x0800 -#define DEB_TXADDR 0x1000 -#define DEB_RXFRAME 0x2000 -#define DEB_INTS 0x4000 -#define DEB_STRUCT 0x8000 -#define DEB_ANY 0xffff - - -#define DEB(x,y) if (i596_debug & (x)) { y; } - - -#define CHECK_WBACK(priv, addr,len) \ - do { dma_cache_sync((priv)->dev, (void *)addr, len, DMA_TO_DEVICE); } while (0) - -#define CHECK_INV(priv, addr,len) \ - do { dma_cache_sync((priv)->dev, (void *)addr, len, DMA_FROM_DEVICE); } while(0) - -#define CHECK_WBACK_INV(priv, addr,len) \ - do { dma_cache_sync((priv)->dev, (void *)addr, len, DMA_BIDIRECTIONAL); } while (0) - - #define PA_I82596_RESET 0 /* Offsets relative to LASI-LAN-Addr.*/ #define PA_CPU_PORT_L_ACCESS 4 #define PA_CHANNEL_ATTENTION 8 +#define OPT_SWAP_PORT 0x0001 /* Need to wordswp on the MPU port */ -/* - * Define various macros for Channel Attention, word swapping etc., dependent - * on architecture. MVME and BVME are 680x0 based, otherwise it is Intel. - */ +#define DMA_ALLOC dma_alloc_noncoherent +#define DMA_FREE dma_free_noncoherent +#define DMA_WBACK(ndev, addr, len) \ + do { dma_cache_sync((ndev)->dev.parent, (void *)addr, len, DMA_TO_DEVICE); } while (0) -#ifdef __BIG_ENDIAN -#define WSWAPrfd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPrbd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPiscp(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPscb(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPcmd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPtbd(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define WSWAPchar(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) -#define ISCP_BUSY 0x00010000 -#define MACH_IS_APRICOT 0 -#else -#define WSWAPrfd(x) ((struct i596_rfd *)(x)) -#define WSWAPrbd(x) ((struct i596_rbd *)(x)) -#define WSWAPiscp(x) ((struct i596_iscp *)(x)) -#define WSWAPscb(x) ((struct i596_scb *)(x)) -#define WSWAPcmd(x) ((struct i596_cmd *)(x)) -#define WSWAPtbd(x) ((struct i596_tbd *)(x)) -#define WSWAPchar(x) ((char *)(x)) -#define ISCP_BUSY 0x0001 -#define MACH_IS_APRICOT 1 -#endif +#define DMA_INV(ndev, addr, len) \ + do { dma_cache_sync((ndev)->dev.parent, (void *)addr, len, DMA_FROM_DEVICE); } while (0) -/* - * The MPU_PORT command allows direct access to the 82596. With PORT access - * the following commands are available (p5-18). The 32-bit port command - * must be word-swapped with the most significant word written first. - * This only applies to VME boards. - */ -#define PORT_RESET 0x00 /* reset 82596 */ -#define PORT_SELFTEST 0x01 /* selftest */ -#define PORT_ALTSCP 0x02 /* alternate SCB address */ -#define PORT_ALTDUMP 0x03 /* Alternate DUMP address */ +#define DMA_WBACK_INV(ndev, addr, len) \ + do { dma_cache_sync((ndev)->dev.parent, (void *)addr, len, DMA_BIDIRECTIONAL); } while (0) + +#define SYSBUS 0x0000006c; + +/* big endian CPU, 82596 "big" endian mode */ +#define SWAP32(x) (((u32)(x)<<16) | ((((u32)(x)))>>16)) +#define SWAP16(x) (x) -static int i596_debug = (DEB_SERIOUS|DEB_PROBE); +#include "lib82596.c" MODULE_AUTHOR("Richard Hirst"); MODULE_DESCRIPTION("i82596 driver"); @@ -180,255 +123,15 @@ MODULE_LICENSE("GPL"); module_param(i596_debug, int, 0); MODULE_PARM_DESC(i596_debug, "lasi_82596 debug mask"); -/* Copy frames shorter than rx_copybreak, otherwise pass on up in - * a full sized sk_buff. Value of 100 stolen from tulip.c (!alpha). - */ -static int rx_copybreak = 100; - -#define MAX_DRIVERS 4 /* max count of drivers */ - -#define PKT_BUF_SZ 1536 -#define MAX_MC_CNT 64 - -#define I596_NULL ((u32)0xffffffff) - -#define CMD_EOL 0x8000 /* The last command of the list, stop. */ -#define CMD_SUSP 0x4000 /* Suspend after doing cmd. */ -#define CMD_INTR 0x2000 /* Interrupt after doing cmd. */ - -#define CMD_FLEX 0x0008 /* Enable flexible memory model */ - -enum commands { - CmdNOp = 0, CmdSASetup = 1, CmdConfigure = 2, CmdMulticastList = 3, - CmdTx = 4, CmdTDR = 5, CmdDump = 6, CmdDiagnose = 7 -}; - -#define STAT_C 0x8000 /* Set to 0 after execution */ -#define STAT_B 0x4000 /* Command being executed */ -#define STAT_OK 0x2000 /* Command executed ok */ -#define STAT_A 0x1000 /* Command aborted */ - -#define CUC_START 0x0100 -#define CUC_RESUME 0x0200 -#define CUC_SUSPEND 0x0300 -#define CUC_ABORT 0x0400 -#define RX_START 0x0010 -#define RX_RESUME 0x0020 -#define RX_SUSPEND 0x0030 -#define RX_ABORT 0x0040 - -#define TX_TIMEOUT 5 - -#define OPT_SWAP_PORT 0x0001 /* Need to wordswp on the MPU port */ - - -struct i596_reg { - unsigned short porthi; - unsigned short portlo; - u32 ca; -}; - -#define EOF 0x8000 -#define SIZE_MASK 0x3fff - -struct i596_tbd { - unsigned short size; - unsigned short pad; - dma_addr_t next; - dma_addr_t data; - u32 cache_pad[5]; /* Total 32 bytes... */ -}; - -/* The command structure has two 'next' pointers; v_next is the address of - * the next command as seen by the CPU, b_next is the address of the next - * command as seen by the 82596. The b_next pointer, as used by the 82596 - * always references the status field of the next command, rather than the - * v_next field, because the 82596 is unaware of v_next. It may seem more - * logical to put v_next at the end of the structure, but we cannot do that - * because the 82596 expects other fields to be there, depending on command - * type. - */ - -struct i596_cmd { - struct i596_cmd *v_next; /* Address from CPUs viewpoint */ - unsigned short status; - unsigned short command; - dma_addr_t b_next; /* Address from i596 viewpoint */ -}; - -struct tx_cmd { - struct i596_cmd cmd; - dma_addr_t tbd; - unsigned short size; - unsigned short pad; - struct sk_buff *skb; /* So we can free it after tx */ - dma_addr_t dma_addr; -#ifdef __LP64__ - u32 cache_pad[6]; /* Total 64 bytes... */ -#else - u32 cache_pad[1]; /* Total 32 bytes... */ -#endif -}; - -struct tdr_cmd { - struct i596_cmd cmd; - unsigned short status; - unsigned short pad; -}; - -struct mc_cmd { - struct i596_cmd cmd; - short mc_cnt; - char mc_addrs[MAX_MC_CNT*6]; -}; - -struct sa_cmd { - struct i596_cmd cmd; - char eth_addr[8]; -}; - -struct cf_cmd { - struct i596_cmd cmd; - char i596_config[16]; -}; - -struct i596_rfd { - unsigned short stat; - unsigned short cmd; - dma_addr_t b_next; /* Address from i596 viewpoint */ - dma_addr_t rbd; - unsigned short count; - unsigned short size; - struct i596_rfd *v_next; /* Address from CPUs viewpoint */ - struct i596_rfd *v_prev; -#ifndef __LP64__ - u32 cache_pad[2]; /* Total 32 bytes... */ -#endif -}; - -struct i596_rbd { - /* hardware data */ - unsigned short count; - unsigned short zero1; - dma_addr_t b_next; - dma_addr_t b_data; /* Address from i596 viewpoint */ - unsigned short size; - unsigned short zero2; - /* driver data */ - struct sk_buff *skb; - struct i596_rbd *v_next; - dma_addr_t b_addr; /* This rbd addr from i596 view */ - unsigned char *v_data; /* Address from CPUs viewpoint */ - /* Total 32 bytes... */ -#ifdef __LP64__ - u32 cache_pad[4]; -#endif -}; - -/* These values as chosen so struct i596_private fits in one page... */ - -#define TX_RING_SIZE 32 -#define RX_RING_SIZE 16 - -struct i596_scb { - unsigned short status; - unsigned short command; - dma_addr_t cmd; - dma_addr_t rfd; - u32 crc_err; - u32 align_err; - u32 resource_err; - u32 over_err; - u32 rcvdt_err; - u32 short_err; - unsigned short t_on; - unsigned short t_off; -}; - -struct i596_iscp { - u32 stat; - dma_addr_t scb; -}; - -struct i596_scp { - u32 sysbus; - u32 pad; - dma_addr_t iscp; -}; - -struct i596_private { - volatile struct i596_scp scp __attribute__((aligned(32))); - volatile struct i596_iscp iscp __attribute__((aligned(32))); - volatile struct i596_scb scb __attribute__((aligned(32))); - struct sa_cmd sa_cmd __attribute__((aligned(32))); - struct cf_cmd cf_cmd __attribute__((aligned(32))); - struct tdr_cmd tdr_cmd __attribute__((aligned(32))); - struct mc_cmd mc_cmd __attribute__((aligned(32))); - struct i596_rfd rfds[RX_RING_SIZE] __attribute__((aligned(32))); - struct i596_rbd rbds[RX_RING_SIZE] __attribute__((aligned(32))); - struct tx_cmd tx_cmds[TX_RING_SIZE] __attribute__((aligned(32))); - struct i596_tbd tbds[TX_RING_SIZE] __attribute__((aligned(32))); - u32 stat; - int last_restart; - struct i596_rfd *rfd_head; - struct i596_rbd *rbd_head; - struct i596_cmd *cmd_tail; - struct i596_cmd *cmd_head; - int cmd_backlog; - u32 last_cmd; - struct net_device_stats stats; - int next_tx_cmd; - int options; - spinlock_t lock; - dma_addr_t dma_addr; - struct device *dev; -}; - -static const char init_setup[] = -{ - 0x8E, /* length, prefetch on */ - 0xC8, /* fifo to 8, monitor off */ - 0x80, /* don't save bad frames */ - 0x2E, /* No source address insertion, 8 byte preamble */ - 0x00, /* priority and backoff defaults */ - 0x60, /* interframe spacing */ - 0x00, /* slot time LSB */ - 0xf2, /* slot time and retries */ - 0x00, /* promiscuous mode */ - 0x00, /* collision detect */ - 0x40, /* minimum frame length */ - 0xff, - 0x00, - 0x7f /* *multi IA */ }; - -static int i596_open(struct net_device *dev); -static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev); -static irqreturn_t i596_interrupt(int irq, void *dev_id); -static int i596_close(struct net_device *dev); -static struct net_device_stats *i596_get_stats(struct net_device *dev); -static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd); -static void i596_tx_timeout (struct net_device *dev); -static void print_eth(unsigned char *buf, char *str); -static void set_multicast_list(struct net_device *dev); - -static int rx_ring_size = RX_RING_SIZE; -static int ticks_limit = 100; -static int max_cmd_backlog = TX_RING_SIZE-1; - -#ifdef CONFIG_NET_POLL_CONTROLLER -static void i596_poll_controller(struct net_device *dev); -#endif - - -static inline void CA(struct net_device *dev) +static inline void ca(struct net_device *dev) { gsc_writel(0, dev->base_addr + PA_CHANNEL_ATTENTION); } -static inline void MPU_PORT(struct net_device *dev, int c, dma_addr_t x) +static void mpu_port(struct net_device *dev, int c, dma_addr_t x) { - struct i596_private *lp = dev->priv; + struct i596_private *lp = netdev_priv(dev); u32 v = (u32) (c) | (u32) (x); u16 a, b; @@ -446,1078 +149,15 @@ static inline void MPU_PORT(struct net_device *dev, int c, dma_addr_t x) gsc_writel(b, dev->base_addr + PA_CPU_PORT_L_ACCESS); } - -static inline int wait_istat(struct net_device *dev, struct i596_private *lp, int delcnt, char *str) -{ - CHECK_INV(lp, &(lp->iscp), sizeof(struct i596_iscp)); - while (--delcnt && lp->iscp.stat) { - udelay(10); - CHECK_INV(lp, &(lp->iscp), sizeof(struct i596_iscp)); - } - if (!delcnt) { - printk("%s: %s, iscp.stat %04x, didn't clear\n", - dev->name, str, lp->iscp.stat); - return -1; - } - else - return 0; -} - - -static inline int wait_cmd(struct net_device *dev, struct i596_private *lp, int delcnt, char *str) -{ - CHECK_INV(lp, &(lp->scb), sizeof(struct i596_scb)); - while (--delcnt && lp->scb.command) { - udelay(10); - CHECK_INV(lp, &(lp->scb), sizeof(struct i596_scb)); - } - if (!delcnt) { - printk("%s: %s, status %4.4x, cmd %4.4x.\n", - dev->name, str, lp->scb.status, lp->scb.command); - return -1; - } - else - return 0; -} - - -static void i596_display_data(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct i596_cmd *cmd; - struct i596_rfd *rfd; - struct i596_rbd *rbd; - - printk("lp and scp at %p, .sysbus = %08x, .iscp = %08x\n", - &lp->scp, lp->scp.sysbus, lp->scp.iscp); - printk("iscp at %p, iscp.stat = %08x, .scb = %08x\n", - &lp->iscp, lp->iscp.stat, lp->iscp.scb); - printk("scb at %p, scb.status = %04x, .command = %04x," - " .cmd = %08x, .rfd = %08x\n", - &lp->scb, lp->scb.status, lp->scb.command, - lp->scb.cmd, lp->scb.rfd); - printk(" errors: crc %x, align %x, resource %x," - " over %x, rcvdt %x, short %x\n", - lp->scb.crc_err, lp->scb.align_err, lp->scb.resource_err, - lp->scb.over_err, lp->scb.rcvdt_err, lp->scb.short_err); - cmd = lp->cmd_head; - while (cmd != NULL) { - printk("cmd at %p, .status = %04x, .command = %04x, .b_next = %08x\n", - cmd, cmd->status, cmd->command, cmd->b_next); - cmd = cmd->v_next; - } - rfd = lp->rfd_head; - printk("rfd_head = %p\n", rfd); - do { - printk(" %p .stat %04x, .cmd %04x, b_next %08x, rbd %08x," - " count %04x\n", - rfd, rfd->stat, rfd->cmd, rfd->b_next, rfd->rbd, - rfd->count); - rfd = rfd->v_next; - } while (rfd != lp->rfd_head); - rbd = lp->rbd_head; - printk("rbd_head = %p\n", rbd); - do { - printk(" %p .count %04x, b_next %08x, b_data %08x, size %04x\n", - rbd, rbd->count, rbd->b_next, rbd->b_data, rbd->size); - rbd = rbd->v_next; - } while (rbd != lp->rbd_head); - CHECK_INV(lp, lp, sizeof(struct i596_private)); -} - - -#if defined(ENABLE_MVME16x_NET) || defined(ENABLE_BVME6000_NET) -static void i596_error(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - volatile unsigned char *pcc2 = (unsigned char *) 0xfff42000; - - pcc2[0x28] = 1; - pcc2[0x2b] = 0x1d; - printk("%s: Error interrupt\n", dev->name); - i596_display_data(dev); -} -#endif - -#define virt_to_dma(lp,v) ((lp)->dma_addr + (dma_addr_t)((unsigned long)(v)-(unsigned long)(lp))) - -static inline void init_rx_bufs(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - int i; - struct i596_rfd *rfd; - struct i596_rbd *rbd; - - /* First build the Receive Buffer Descriptor List */ - - for (i = 0, rbd = lp->rbds; i < rx_ring_size; i++, rbd++) { - dma_addr_t dma_addr; - struct sk_buff *skb = dev_alloc_skb(PKT_BUF_SZ + 4); - - if (skb == NULL) - panic("%s: alloc_skb() failed", __FILE__); - skb_reserve(skb, 2); - dma_addr = dma_map_single(lp->dev, skb->data,PKT_BUF_SZ, - DMA_FROM_DEVICE); - skb->dev = dev; - rbd->v_next = rbd+1; - rbd->b_next = WSWAPrbd(virt_to_dma(lp,rbd+1)); - rbd->b_addr = WSWAPrbd(virt_to_dma(lp,rbd)); - rbd->skb = skb; - rbd->v_data = skb->data; - rbd->b_data = WSWAPchar(dma_addr); - rbd->size = PKT_BUF_SZ; - } - lp->rbd_head = lp->rbds; - rbd = lp->rbds + rx_ring_size - 1; - rbd->v_next = lp->rbds; - rbd->b_next = WSWAPrbd(virt_to_dma(lp,lp->rbds)); - - /* Now build the Receive Frame Descriptor List */ - - for (i = 0, rfd = lp->rfds; i < rx_ring_size; i++, rfd++) { - rfd->rbd = I596_NULL; - rfd->v_next = rfd+1; - rfd->v_prev = rfd-1; - rfd->b_next = WSWAPrfd(virt_to_dma(lp,rfd+1)); - rfd->cmd = CMD_FLEX; - } - lp->rfd_head = lp->rfds; - lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - rfd = lp->rfds; - rfd->rbd = WSWAPrbd(virt_to_dma(lp,lp->rbd_head)); - rfd->v_prev = lp->rfds + rx_ring_size - 1; - rfd = lp->rfds + rx_ring_size - 1; - rfd->v_next = lp->rfds; - rfd->b_next = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - rfd->cmd = CMD_EOL|CMD_FLEX; - - CHECK_WBACK_INV(lp, lp, sizeof(struct i596_private)); -} - -static inline void remove_rx_bufs(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct i596_rbd *rbd; - int i; - - for (i = 0, rbd = lp->rbds; i < rx_ring_size; i++, rbd++) { - if (rbd->skb == NULL) - break; - dma_unmap_single(lp->dev, - (dma_addr_t)WSWAPchar(rbd->b_data), - PKT_BUF_SZ, DMA_FROM_DEVICE); - dev_kfree_skb(rbd->skb); - } -} - - -static void rebuild_rx_bufs(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - int i; - - /* Ensure rx frame/buffer descriptors are tidy */ - - for (i = 0; i < rx_ring_size; i++) { - lp->rfds[i].rbd = I596_NULL; - lp->rfds[i].cmd = CMD_FLEX; - } - lp->rfds[rx_ring_size-1].cmd = CMD_EOL|CMD_FLEX; - lp->rfd_head = lp->rfds; - lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - lp->rbd_head = lp->rbds; - lp->rfds[0].rbd = WSWAPrbd(virt_to_dma(lp,lp->rbds)); - - CHECK_WBACK_INV(lp, lp, sizeof(struct i596_private)); -} - - -static int init_i596_mem(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - unsigned long flags; - - disable_irq(dev->irq); /* disable IRQs from LAN */ - DEB(DEB_INIT, - printk("RESET 82596 port: %lx (with IRQ %d disabled)\n", - (dev->base_addr + PA_I82596_RESET), - dev->irq)); - - gsc_writel(0, (dev->base_addr + PA_I82596_RESET)); /* Hard Reset */ - udelay(100); /* Wait 100us - seems to help */ - - /* change the scp address */ - - lp->last_cmd = jiffies; - - - lp->scp.sysbus = 0x0000006c; - lp->scp.iscp = WSWAPiscp(virt_to_dma(lp,&(lp->iscp))); - lp->iscp.scb = WSWAPscb(virt_to_dma(lp,&(lp->scb))); - lp->iscp.stat = ISCP_BUSY; - lp->cmd_backlog = 0; - - lp->cmd_head = NULL; - lp->scb.cmd = I596_NULL; - - DEB(DEB_INIT, printk("%s: starting i82596.\n", dev->name)); - - CHECK_WBACK(lp, &(lp->scp), sizeof(struct i596_scp)); - CHECK_WBACK(lp, &(lp->iscp), sizeof(struct i596_iscp)); - - MPU_PORT(dev, PORT_ALTSCP, virt_to_dma(lp,&lp->scp)); - - CA(dev); - - if (wait_istat(dev, lp, 1000, "initialization timed out")) - goto failed; - DEB(DEB_INIT, printk("%s: i82596 initialization successful\n", dev->name)); - - /* Ensure rx frame/buffer descriptors are tidy */ - rebuild_rx_bufs(dev); - - lp->scb.command = 0; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - - enable_irq(dev->irq); /* enable IRQs from LAN */ - - DEB(DEB_INIT, printk("%s: queuing CmdConfigure\n", dev->name)); - memcpy(lp->cf_cmd.i596_config, init_setup, sizeof(init_setup)); - lp->cf_cmd.cmd.command = CmdConfigure; - CHECK_WBACK(lp, &(lp->cf_cmd), sizeof(struct cf_cmd)); - i596_add_cmd(dev, &lp->cf_cmd.cmd); - - DEB(DEB_INIT, printk("%s: queuing CmdSASetup\n", dev->name)); - memcpy(lp->sa_cmd.eth_addr, dev->dev_addr, 6); - lp->sa_cmd.cmd.command = CmdSASetup; - CHECK_WBACK(lp, &(lp->sa_cmd), sizeof(struct sa_cmd)); - i596_add_cmd(dev, &lp->sa_cmd.cmd); - - DEB(DEB_INIT, printk("%s: queuing CmdTDR\n", dev->name)); - lp->tdr_cmd.cmd.command = CmdTDR; - CHECK_WBACK(lp, &(lp->tdr_cmd), sizeof(struct tdr_cmd)); - i596_add_cmd(dev, &lp->tdr_cmd.cmd); - - spin_lock_irqsave (&lp->lock, flags); - - if (wait_cmd(dev, lp, 1000, "timed out waiting to issue RX_START")) { - spin_unlock_irqrestore (&lp->lock, flags); - goto failed; - } - DEB(DEB_INIT, printk("%s: Issuing RX_START\n", dev->name)); - lp->scb.command = RX_START; - lp->scb.rfd = WSWAPrfd(virt_to_dma(lp,lp->rfds)); - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - - CA(dev); - - spin_unlock_irqrestore (&lp->lock, flags); - - if (wait_cmd(dev, lp, 1000, "RX_START not processed")) - goto failed; - DEB(DEB_INIT, printk("%s: Receive unit started OK\n", dev->name)); - - return 0; - -failed: - printk("%s: Failed to initialise 82596\n", dev->name); - MPU_PORT(dev, PORT_RESET, 0); - return -1; -} - - -static inline int i596_rx(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct i596_rfd *rfd; - struct i596_rbd *rbd; - int frames = 0; - - DEB(DEB_RXFRAME, printk("i596_rx(), rfd_head %p, rbd_head %p\n", - lp->rfd_head, lp->rbd_head)); - - - rfd = lp->rfd_head; /* Ref next frame to check */ - - CHECK_INV(lp, rfd, sizeof(struct i596_rfd)); - while ((rfd->stat) & STAT_C) { /* Loop while complete frames */ - if (rfd->rbd == I596_NULL) - rbd = NULL; - else if (rfd->rbd == lp->rbd_head->b_addr) { - rbd = lp->rbd_head; - CHECK_INV(lp, rbd, sizeof(struct i596_rbd)); - } - else { - printk("%s: rbd chain broken!\n", dev->name); - /* XXX Now what? */ - rbd = NULL; - } - DEB(DEB_RXFRAME, printk(" rfd %p, rfd.rbd %08x, rfd.stat %04x\n", - rfd, rfd->rbd, rfd->stat)); - - if (rbd != NULL && ((rfd->stat) & STAT_OK)) { - /* a good frame */ - int pkt_len = rbd->count & 0x3fff; - struct sk_buff *skb = rbd->skb; - int rx_in_place = 0; - - DEB(DEB_RXADDR,print_eth(rbd->v_data, "received")); - frames++; - - /* Check if the packet is long enough to just accept - * without copying to a properly sized skbuff. - */ - - if (pkt_len > rx_copybreak) { - struct sk_buff *newskb; - dma_addr_t dma_addr; - - dma_unmap_single(lp->dev,(dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); - /* Get fresh skbuff to replace filled one. */ - newskb = dev_alloc_skb(PKT_BUF_SZ + 4); - if (newskb == NULL) { - skb = NULL; /* drop pkt */ - goto memory_squeeze; - } - skb_reserve(newskb, 2); - - /* Pass up the skb already on the Rx ring. */ - skb_put(skb, pkt_len); - rx_in_place = 1; - rbd->skb = newskb; - newskb->dev = dev; - dma_addr = dma_map_single(lp->dev, newskb->data, PKT_BUF_SZ, DMA_FROM_DEVICE); - rbd->v_data = newskb->data; - rbd->b_data = WSWAPchar(dma_addr); - CHECK_WBACK_INV(lp, rbd, sizeof(struct i596_rbd)); - } - else - skb = dev_alloc_skb(pkt_len + 2); -memory_squeeze: - if (skb == NULL) { - /* XXX tulip.c can defer packets here!! */ - printk("%s: i596_rx Memory squeeze, dropping packet.\n", dev->name); - lp->stats.rx_dropped++; - } - else { - if (!rx_in_place) { - /* 16 byte align the data fields */ - dma_sync_single_for_cpu(lp->dev, (dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); - skb_reserve(skb, 2); - memcpy(skb_put(skb,pkt_len), rbd->v_data, pkt_len); - dma_sync_single_for_device(lp->dev, (dma_addr_t)WSWAPchar(rbd->b_data), PKT_BUF_SZ, DMA_FROM_DEVICE); - } - skb->len = pkt_len; - skb->protocol=eth_type_trans(skb,dev); - netif_rx(skb); - dev->last_rx = jiffies; - lp->stats.rx_packets++; - lp->stats.rx_bytes+=pkt_len; - } - } - else { - DEB(DEB_ERRORS, printk("%s: Error, rfd.stat = 0x%04x\n", - dev->name, rfd->stat)); - lp->stats.rx_errors++; - if ((rfd->stat) & 0x0001) - lp->stats.collisions++; - if ((rfd->stat) & 0x0080) - lp->stats.rx_length_errors++; - if ((rfd->stat) & 0x0100) - lp->stats.rx_over_errors++; - if ((rfd->stat) & 0x0200) - lp->stats.rx_fifo_errors++; - if ((rfd->stat) & 0x0400) - lp->stats.rx_frame_errors++; - if ((rfd->stat) & 0x0800) - lp->stats.rx_crc_errors++; - if ((rfd->stat) & 0x1000) - lp->stats.rx_length_errors++; - } - - /* Clear the buffer descriptor count and EOF + F flags */ - - if (rbd != NULL && (rbd->count & 0x4000)) { - rbd->count = 0; - lp->rbd_head = rbd->v_next; - CHECK_WBACK_INV(lp, rbd, sizeof(struct i596_rbd)); - } - - /* Tidy the frame descriptor, marking it as end of list */ - - rfd->rbd = I596_NULL; - rfd->stat = 0; - rfd->cmd = CMD_EOL|CMD_FLEX; - rfd->count = 0; - - /* Remove end-of-list from old end descriptor */ - - rfd->v_prev->cmd = CMD_FLEX; - - /* Update record of next frame descriptor to process */ - - lp->scb.rfd = rfd->b_next; - lp->rfd_head = rfd->v_next; - CHECK_WBACK_INV(lp, rfd->v_prev, sizeof(struct i596_rfd)); - CHECK_WBACK_INV(lp, rfd, sizeof(struct i596_rfd)); - rfd = lp->rfd_head; - CHECK_INV(lp, rfd, sizeof(struct i596_rfd)); - } - - DEB(DEB_RXFRAME, printk("frames %d\n", frames)); - - return 0; -} - - -static inline void i596_cleanup_cmd(struct net_device *dev, struct i596_private *lp) -{ - struct i596_cmd *ptr; - - while (lp->cmd_head != NULL) { - ptr = lp->cmd_head; - lp->cmd_head = ptr->v_next; - lp->cmd_backlog--; - - switch ((ptr->command) & 0x7) { - case CmdTx: - { - struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; - struct sk_buff *skb = tx_cmd->skb; - dma_unmap_single(lp->dev, tx_cmd->dma_addr, skb->len, DMA_TO_DEVICE); - - dev_kfree_skb(skb); - - lp->stats.tx_errors++; - lp->stats.tx_aborted_errors++; - - ptr->v_next = NULL; - ptr->b_next = I596_NULL; - tx_cmd->cmd.command = 0; /* Mark as free */ - break; - } - default: - ptr->v_next = NULL; - ptr->b_next = I596_NULL; - } - CHECK_WBACK_INV(lp, ptr, sizeof(struct i596_cmd)); - } - - wait_cmd(dev, lp, 100, "i596_cleanup_cmd timed out"); - lp->scb.cmd = I596_NULL; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); -} - - -static inline void i596_reset(struct net_device *dev, struct i596_private *lp) -{ - unsigned long flags; - - DEB(DEB_RESET, printk("i596_reset\n")); - - spin_lock_irqsave (&lp->lock, flags); - - wait_cmd(dev, lp, 100, "i596_reset timed out"); - - netif_stop_queue(dev); - - /* FIXME: this command might cause an lpmc */ - lp->scb.command = CUC_ABORT | RX_ABORT; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - CA(dev); - - /* wait for shutdown */ - wait_cmd(dev, lp, 1000, "i596_reset 2 timed out"); - spin_unlock_irqrestore (&lp->lock, flags); - - i596_cleanup_cmd(dev,lp); - i596_rx(dev); - - netif_start_queue(dev); - init_i596_mem(dev); -} - - -static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd) -{ - struct i596_private *lp = dev->priv; - unsigned long flags; - - DEB(DEB_ADDCMD, printk("i596_add_cmd cmd_head %p\n", lp->cmd_head)); - - cmd->status = 0; - cmd->command |= (CMD_EOL | CMD_INTR); - cmd->v_next = NULL; - cmd->b_next = I596_NULL; - CHECK_WBACK(lp, cmd, sizeof(struct i596_cmd)); - - spin_lock_irqsave (&lp->lock, flags); - - if (lp->cmd_head != NULL) { - lp->cmd_tail->v_next = cmd; - lp->cmd_tail->b_next = WSWAPcmd(virt_to_dma(lp,&cmd->status)); - CHECK_WBACK(lp, lp->cmd_tail, sizeof(struct i596_cmd)); - } else { - lp->cmd_head = cmd; - wait_cmd(dev, lp, 100, "i596_add_cmd timed out"); - lp->scb.cmd = WSWAPcmd(virt_to_dma(lp,&cmd->status)); - lp->scb.command = CUC_START; - CHECK_WBACK(lp, &(lp->scb), sizeof(struct i596_scb)); - CA(dev); - } - lp->cmd_tail = cmd; - lp->cmd_backlog++; - - spin_unlock_irqrestore (&lp->lock, flags); - - if (lp->cmd_backlog > max_cmd_backlog) { - unsigned long tickssofar = jiffies - lp->last_cmd; - - if (tickssofar < ticks_limit) - return; - - printk("%s: command unit timed out, status resetting.\n", dev->name); -#if 1 - i596_reset(dev, lp); -#endif - } -} - -#if 0 -/* this function makes a perfectly adequate probe... but we have a - device list */ -static int i596_test(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - volatile int *tint; - u32 data; - - tint = (volatile int *)(&(lp->scp)); - data = virt_to_dma(lp,tint); - - tint[1] = -1; - CHECK_WBACK(lp, tint, PAGE_SIZE); - - MPU_PORT(dev, 1, data); - - for(data = 1000000; data; data--) { - CHECK_INV(lp, tint, PAGE_SIZE); - if(tint[1] != -1) - break; - - } - - printk("i596_test result %d\n", tint[1]); - -} -#endif - - -static int i596_open(struct net_device *dev) -{ - DEB(DEB_OPEN, printk("%s: i596_open() irq %d.\n", dev->name, dev->irq)); - - if (request_irq(dev->irq, &i596_interrupt, 0, "i82596", dev)) { - printk("%s: IRQ %d not free\n", dev->name, dev->irq); - goto out; - } - - init_rx_bufs(dev); - - if (init_i596_mem(dev)) { - printk("%s: Failed to init memory\n", dev->name); - goto out_remove_rx_bufs; - } - - netif_start_queue(dev); - - return 0; - -out_remove_rx_bufs: - remove_rx_bufs(dev); - free_irq(dev->irq, dev); -out: - return -EAGAIN; -} - -static void i596_tx_timeout (struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - - /* Transmitter timeout, serious problems. */ - DEB(DEB_ERRORS, printk("%s: transmit timed out, status resetting.\n", - dev->name)); - - lp->stats.tx_errors++; - - /* Try to restart the adaptor */ - if (lp->last_restart == lp->stats.tx_packets) { - DEB(DEB_ERRORS, printk("Resetting board.\n")); - /* Shutdown and restart */ - i596_reset (dev, lp); - } else { - /* Issue a channel attention signal */ - DEB(DEB_ERRORS, printk("Kicking board.\n")); - lp->scb.command = CUC_START | RX_START; - CHECK_WBACK_INV(lp, &(lp->scb), sizeof(struct i596_scb)); - CA (dev); - lp->last_restart = lp->stats.tx_packets; - } - - dev->trans_start = jiffies; - netif_wake_queue (dev); -} - - -static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - struct tx_cmd *tx_cmd; - struct i596_tbd *tbd; - short length = skb->len; - dev->trans_start = jiffies; - - DEB(DEB_STARTTX, printk("%s: i596_start_xmit(%x,%p) called\n", dev->name, - skb->len, skb->data)); - - if (length < ETH_ZLEN) { - if (skb_padto(skb, ETH_ZLEN)) - return 0; - length = ETH_ZLEN; - } - - netif_stop_queue(dev); - - tx_cmd = lp->tx_cmds + lp->next_tx_cmd; - tbd = lp->tbds + lp->next_tx_cmd; - - if (tx_cmd->cmd.command) { - DEB(DEB_ERRORS, printk("%s: xmit ring full, dropping packet.\n", - dev->name)); - lp->stats.tx_dropped++; - - dev_kfree_skb(skb); - } else { - if (++lp->next_tx_cmd == TX_RING_SIZE) - lp->next_tx_cmd = 0; - tx_cmd->tbd = WSWAPtbd(virt_to_dma(lp,tbd)); - tbd->next = I596_NULL; - - tx_cmd->cmd.command = CMD_FLEX | CmdTx; - tx_cmd->skb = skb; - - tx_cmd->pad = 0; - tx_cmd->size = 0; - tbd->pad = 0; - tbd->size = EOF | length; - - tx_cmd->dma_addr = dma_map_single(lp->dev, skb->data, skb->len, - DMA_TO_DEVICE); - tbd->data = WSWAPchar(tx_cmd->dma_addr); - - DEB(DEB_TXADDR,print_eth(skb->data, "tx-queued")); - CHECK_WBACK_INV(lp, tx_cmd, sizeof(struct tx_cmd)); - CHECK_WBACK_INV(lp, tbd, sizeof(struct i596_tbd)); - i596_add_cmd(dev, &tx_cmd->cmd); - - lp->stats.tx_packets++; - lp->stats.tx_bytes += length; - } - - netif_start_queue(dev); - - return 0; -} - -static void print_eth(unsigned char *add, char *str) -{ - int i; - - printk("i596 0x%p, ", add); - for (i = 0; i < 6; i++) - printk(" %02X", add[i + 6]); - printk(" -->"); - for (i = 0; i < 6; i++) - printk(" %02X", add[i]); - printk(" %02X%02X, %s\n", add[12], add[13], str); -} - - #define LAN_PROM_ADDR 0xF0810000 -static int __devinit i82596_probe(struct net_device *dev, - struct device *gen_dev) -{ - int i; - struct i596_private *lp; - char eth_addr[6]; - dma_addr_t dma_addr; - - /* This lot is ensure things have been cache line aligned. */ - BUILD_BUG_ON(sizeof(struct i596_rfd) != 32); - BUILD_BUG_ON(sizeof(struct i596_rbd) & 31); - BUILD_BUG_ON(sizeof(struct tx_cmd) & 31); - BUILD_BUG_ON(sizeof(struct i596_tbd) != 32); -#ifndef __LP64__ - BUILD_BUG_ON(sizeof(struct i596_private) > 4096); -#endif - - if (!dev->base_addr || !dev->irq) - return -ENODEV; - - if (pdc_lan_station_id(eth_addr, dev->base_addr)) { - for (i=0; i < 6; i++) { - eth_addr[i] = gsc_readb(LAN_PROM_ADDR + i); - } - printk(KERN_INFO "%s: MAC of HP700 LAN read from EEPROM\n", __FILE__); - } - - dev->mem_start = (unsigned long) dma_alloc_noncoherent(gen_dev, - sizeof(struct i596_private), &dma_addr, GFP_KERNEL); - if (!dev->mem_start) { - printk(KERN_ERR "%s: Couldn't get shared memory\n", __FILE__); - return -ENOMEM; - } - - for (i = 0; i < 6; i++) - dev->dev_addr[i] = eth_addr[i]; - - /* The 82596-specific entries in the device structure. */ - dev->open = i596_open; - dev->stop = i596_close; - dev->hard_start_xmit = i596_start_xmit; - dev->get_stats = i596_get_stats; - dev->set_multicast_list = set_multicast_list; - dev->tx_timeout = i596_tx_timeout; - dev->watchdog_timeo = TX_TIMEOUT; -#ifdef CONFIG_NET_POLL_CONTROLLER - dev->poll_controller = i596_poll_controller; -#endif - - dev->priv = (void *)(dev->mem_start); - - lp = dev->priv; - memset(lp, 0, sizeof(struct i596_private)); - - lp->scb.command = 0; - lp->scb.cmd = I596_NULL; - lp->scb.rfd = I596_NULL; - spin_lock_init(&lp->lock); - lp->dma_addr = dma_addr; - lp->dev = gen_dev; - - CHECK_WBACK_INV(lp, dev->mem_start, sizeof(struct i596_private)); - - i = register_netdev(dev); - if (i) { - lp = dev->priv; - dma_free_noncoherent(lp->dev, sizeof(struct i596_private), - (void *)dev->mem_start, lp->dma_addr); - return i; - }; - - DEB(DEB_PROBE, printk(KERN_INFO "%s: 82596 at %#3lx,", dev->name, dev->base_addr)); - for (i = 0; i < 6; i++) - DEB(DEB_PROBE, printk(" %2.2X", dev->dev_addr[i])); - DEB(DEB_PROBE, printk(" IRQ %d.\n", dev->irq)); - DEB(DEB_INIT, printk(KERN_INFO "%s: lp at 0x%p (%d bytes), lp->scb at 0x%p\n", - dev->name, lp, (int)sizeof(struct i596_private), &lp->scb)); - - return 0; -} - -#ifdef CONFIG_NET_POLL_CONTROLLER -static void i596_poll_controller(struct net_device *dev) -{ - disable_irq(dev->irq); - i596_interrupt(dev->irq, dev); - enable_irq(dev->irq); -} -#endif - -static irqreturn_t i596_interrupt(int irq, void *dev_id) -{ - struct net_device *dev = dev_id; - struct i596_private *lp; - unsigned short status, ack_cmd = 0; - - if (dev == NULL) { - printk("%s: irq %d for unknown device.\n", __FUNCTION__, irq); - return IRQ_NONE; - } - - lp = dev->priv; - - spin_lock (&lp->lock); - - wait_cmd(dev, lp, 100, "i596 interrupt, timeout"); - status = lp->scb.status; - - DEB(DEB_INTS, printk("%s: i596 interrupt, IRQ %d, status %4.4x.\n", - dev->name, irq, status)); - - ack_cmd = status & 0xf000; - - if (!ack_cmd) { - DEB(DEB_ERRORS, printk("%s: interrupt with no events\n", dev->name)); - spin_unlock (&lp->lock); - return IRQ_NONE; - } - - if ((status & 0x8000) || (status & 0x2000)) { - struct i596_cmd *ptr; - - if ((status & 0x8000)) - DEB(DEB_INTS, printk("%s: i596 interrupt completed command.\n", dev->name)); - if ((status & 0x2000)) - DEB(DEB_INTS, printk("%s: i596 interrupt command unit inactive %x.\n", dev->name, status & 0x0700)); - - while (lp->cmd_head != NULL) { - CHECK_INV(lp, lp->cmd_head, sizeof(struct i596_cmd)); - if (!(lp->cmd_head->status & STAT_C)) - break; - - ptr = lp->cmd_head; - - DEB(DEB_STATUS, printk("cmd_head->status = %04x, ->command = %04x\n", - lp->cmd_head->status, lp->cmd_head->command)); - lp->cmd_head = ptr->v_next; - lp->cmd_backlog--; - - switch ((ptr->command) & 0x7) { - case CmdTx: - { - struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; - struct sk_buff *skb = tx_cmd->skb; - - if ((ptr->status) & STAT_OK) { - DEB(DEB_TXADDR, print_eth(skb->data, "tx-done")); - } else { - lp->stats.tx_errors++; - if ((ptr->status) & 0x0020) - lp->stats.collisions++; - if (!((ptr->status) & 0x0040)) - lp->stats.tx_heartbeat_errors++; - if ((ptr->status) & 0x0400) - lp->stats.tx_carrier_errors++; - if ((ptr->status) & 0x0800) - lp->stats.collisions++; - if ((ptr->status) & 0x1000) - lp->stats.tx_aborted_errors++; - } - dma_unmap_single(lp->dev, tx_cmd->dma_addr, skb->len, DMA_TO_DEVICE); - dev_kfree_skb_irq(skb); - - tx_cmd->cmd.command = 0; /* Mark free */ - break; - } - case CmdTDR: - { - unsigned short status = ((struct tdr_cmd *)ptr)->status; - - if (status & 0x8000) { - DEB(DEB_ANY, printk("%s: link ok.\n", dev->name)); - } else { - if (status & 0x4000) - printk("%s: Transceiver problem.\n", dev->name); - if (status & 0x2000) - printk("%s: Termination problem.\n", dev->name); - if (status & 0x1000) - printk("%s: Short circuit.\n", dev->name); - - DEB(DEB_TDR, printk("%s: Time %d.\n", dev->name, status & 0x07ff)); - } - break; - } - case CmdConfigure: - /* Zap command so set_multicast_list() knows it is free */ - ptr->command = 0; - break; - } - ptr->v_next = NULL; - ptr->b_next = I596_NULL; - CHECK_WBACK(lp, ptr, sizeof(struct i596_cmd)); - lp->last_cmd = jiffies; - } - - /* This mess is arranging that only the last of any outstanding - * commands has the interrupt bit set. Should probably really - * only add to the cmd queue when the CU is stopped. - */ - ptr = lp->cmd_head; - while ((ptr != NULL) && (ptr != lp->cmd_tail)) { - struct i596_cmd *prev = ptr; - - ptr->command &= 0x1fff; - ptr = ptr->v_next; - CHECK_WBACK_INV(lp, prev, sizeof(struct i596_cmd)); - } - - if ((lp->cmd_head != NULL)) - ack_cmd |= CUC_START; - lp->scb.cmd = WSWAPcmd(virt_to_dma(lp,&lp->cmd_head->status)); - CHECK_WBACK_INV(lp, &lp->scb, sizeof(struct i596_scb)); - } - if ((status & 0x1000) || (status & 0x4000)) { - if ((status & 0x4000)) - DEB(DEB_INTS, printk("%s: i596 interrupt received a frame.\n", dev->name)); - i596_rx(dev); - /* Only RX_START if stopped - RGH 07-07-96 */ - if (status & 0x1000) { - if (netif_running(dev)) { - DEB(DEB_ERRORS, printk("%s: i596 interrupt receive unit inactive, status 0x%x\n", dev->name, status)); - ack_cmd |= RX_START; - lp->stats.rx_errors++; - lp->stats.rx_fifo_errors++; - rebuild_rx_bufs(dev); - } - } - } - wait_cmd(dev, lp, 100, "i596 interrupt, timeout"); - lp->scb.command = ack_cmd; - CHECK_WBACK(lp, &lp->scb, sizeof(struct i596_scb)); - - /* DANGER: I suspect that some kind of interrupt - acknowledgement aside from acking the 82596 might be needed - here... but it's running acceptably without */ - - CA(dev); - - wait_cmd(dev, lp, 100, "i596 interrupt, exit timeout"); - DEB(DEB_INTS, printk("%s: exiting interrupt.\n", dev->name)); - - spin_unlock (&lp->lock); - return IRQ_HANDLED; -} - -static int i596_close(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - unsigned long flags; - - netif_stop_queue(dev); - - DEB(DEB_INIT, printk("%s: Shutting down ethercard, status was %4.4x.\n", - dev->name, lp->scb.status)); - - spin_lock_irqsave(&lp->lock, flags); - - wait_cmd(dev, lp, 100, "close1 timed out"); - lp->scb.command = CUC_ABORT | RX_ABORT; - CHECK_WBACK(lp, &lp->scb, sizeof(struct i596_scb)); - - CA(dev); - - wait_cmd(dev, lp, 100, "close2 timed out"); - spin_unlock_irqrestore(&lp->lock, flags); - DEB(DEB_STRUCT,i596_display_data(dev)); - i596_cleanup_cmd(dev,lp); - - disable_irq(dev->irq); - - free_irq(dev->irq, dev); - remove_rx_bufs(dev); - - return 0; -} - -static struct net_device_stats * - i596_get_stats(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - - return &lp->stats; -} - -/* - * Set or clear the multicast filter for this adaptor. - */ - -static void set_multicast_list(struct net_device *dev) -{ - struct i596_private *lp = dev->priv; - int config = 0, cnt; - - DEB(DEB_MULTI, printk("%s: set multicast list, %d entries, promisc %s, allmulti %s\n", - dev->name, dev->mc_count, dev->flags & IFF_PROMISC ? "ON" : "OFF", - dev->flags & IFF_ALLMULTI ? "ON" : "OFF")); - - if ((dev->flags & IFF_PROMISC) && !(lp->cf_cmd.i596_config[8] & 0x01)) { - lp->cf_cmd.i596_config[8] |= 0x01; - config = 1; - } - if (!(dev->flags & IFF_PROMISC) && (lp->cf_cmd.i596_config[8] & 0x01)) { - lp->cf_cmd.i596_config[8] &= ~0x01; - config = 1; - } - if ((dev->flags & IFF_ALLMULTI) && (lp->cf_cmd.i596_config[11] & 0x20)) { - lp->cf_cmd.i596_config[11] &= ~0x20; - config = 1; - } - if (!(dev->flags & IFF_ALLMULTI) && !(lp->cf_cmd.i596_config[11] & 0x20)) { - lp->cf_cmd.i596_config[11] |= 0x20; - config = 1; - } - if (config) { - if (lp->cf_cmd.cmd.command) - printk("%s: config change request already queued\n", - dev->name); - else { - lp->cf_cmd.cmd.command = CmdConfigure; - CHECK_WBACK_INV(lp, &lp->cf_cmd, sizeof(struct cf_cmd)); - i596_add_cmd(dev, &lp->cf_cmd.cmd); - } - } - - cnt = dev->mc_count; - if (cnt > MAX_MC_CNT) - { - cnt = MAX_MC_CNT; - printk("%s: Only %d multicast addresses supported", - dev->name, cnt); - } - - if (dev->mc_count > 0) { - struct dev_mc_list *dmi; - unsigned char *cp; - struct mc_cmd *cmd; - - cmd = &lp->mc_cmd; - cmd->cmd.command = CmdMulticastList; - cmd->mc_cnt = dev->mc_count * 6; - cp = cmd->mc_addrs; - for (dmi = dev->mc_list; cnt && dmi != NULL; dmi = dmi->next, cnt--, cp += 6) { - memcpy(cp, dmi->dmi_addr, 6); - if (i596_debug > 1) - DEB(DEB_MULTI, printk("%s: Adding address %02x:%02x:%02x:%02x:%02x:%02x\n", - dev->name, cp[0],cp[1],cp[2],cp[3],cp[4],cp[5])); - } - CHECK_WBACK_INV(lp, &lp->mc_cmd, sizeof(struct mc_cmd)); - i596_add_cmd(dev, &cmd->cmd); - } -} - -static int debug = -1; -module_param(debug, int, 0); -MODULE_PARM_DESC(debug, "lasi_82596 debug mask"); - -static int num_drivers; -static struct net_device *netdevs[MAX_DRIVERS]; - static int __devinit lan_init_chip(struct parisc_device *dev) { struct net_device *netdevice; + struct i596_private *lp; int retval; - - if (num_drivers >= MAX_DRIVERS) { - /* max count of possible i82596 drivers reached */ - return -ENOMEM; - } - - if (num_drivers == 0) - printk(KERN_INFO LASI_82596_DRIVER_VERSION "\n"); + int i; if (!dev->irq) { printk(KERN_ERR "%s: IRQ not found for i82596 at 0x%lx\n", @@ -1528,28 +168,45 @@ lan_init_chip(struct parisc_device *dev) printk(KERN_INFO "Found i82596 at 0x%lx, IRQ %d\n", dev->hpa.start, dev->irq); - netdevice = alloc_etherdev(0); + netdevice = alloc_etherdev(sizeof(struct i596_private)); if (!netdevice) return -ENOMEM; + SET_NETDEV_DEV(netdevice, &dev->dev); + parisc_set_drvdata (dev, netdevice); netdevice->base_addr = dev->hpa.start; netdevice->irq = dev->irq; - retval = i82596_probe(netdevice, &dev->dev); + if (pdc_lan_station_id(netdevice->dev_addr, netdevice->base_addr)) { + for (i = 0; i < 6; i++) { + netdevice->dev_addr[i] = gsc_readb(LAN_PROM_ADDR + i); + } + printk(KERN_INFO + "%s: MAC of HP700 LAN read from EEPROM\n", __FILE__); + } + + lp = netdev_priv(netdevice); + lp->options = dev->id.sversion == 0x72 ? OPT_SWAP_PORT : 0; + + retval = i82596_probe(netdevice); if (retval) { free_netdev(netdevice); return -ENODEV; } - - if (dev->id.sversion == 0x72) { - ((struct i596_private *)netdevice->priv)->options = OPT_SWAP_PORT; - } - - netdevs[num_drivers++] = netdevice; - return retval; } +static int __devexit lan_remove_chip (struct parisc_device *pdev) +{ + struct net_device *dev = parisc_get_drvdata(pdev); + struct i596_private *lp = netdev_priv(dev); + + unregister_netdev (dev); + DMA_FREE(&pdev->dev, sizeof(struct i596_private), + (void *)lp->dma, lp->dma_addr); + free_netdev (dev); + return 0; +} static struct parisc_device_id lan_tbl[] = { { HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0008a }, @@ -1563,12 +220,12 @@ static struct parisc_driver lan_driver = { .name = "lasi_82596", .id_table = lan_tbl, .probe = lan_init_chip, + .remove = __devexit_p(lan_remove_chip), }; static int __devinit lasi_82596_init(void) { - if (debug >= 0) - i596_debug = debug; + printk(KERN_INFO LASI_82596_DRIVER_VERSION "\n"); return register_parisc_driver(&lan_driver); } @@ -1576,25 +233,6 @@ module_init(lasi_82596_init); static void __exit lasi_82596_exit(void) { - int i; - - for (i=0; i<MAX_DRIVERS; i++) { - struct i596_private *lp; - struct net_device *netdevice; - - netdevice = netdevs[i]; - if (!netdevice) - continue; - - unregister_netdev(netdevice); - - lp = netdevice->priv; - dma_free_noncoherent(lp->dev, sizeof(struct i596_private), - (void *)netdevice->mem_start, lp->dma_addr); - free_netdev(netdevice); - } - num_drivers = 0; - unregister_parisc_driver(&lan_driver); } diff --git a/drivers/net/lib82596.c b/drivers/net/lib82596.c new file mode 100644 index 00000000000..5884f5bd04a --- /dev/null +++ b/drivers/net/lib82596.c @@ -0,0 +1,1434 @@ +/* lasi_82596.c -- driver for the intel 82596 ethernet controller, as + munged into HPPA boxen . + + This driver is based upon 82596.c, original credits are below... + but there were too many hoops which HP wants jumped through to + keep this code in there in a sane manner. + + 3 primary sources of the mess -- + 1) hppa needs *lots* of cacheline flushing to keep this kind of + MMIO running. + + 2) The 82596 needs to see all of its pointers as their physical + address. Thus virt_to_bus/bus_to_virt are *everywhere*. + + 3) The implementation HP is using seems to be significantly pickier + about when and how the command and RX units are started. some + command ordering was changed. + + Examination of the mach driver leads one to believe that there + might be a saner way to pull this off... anyone who feels like a + full rewrite can be my guest. + + Split 02/13/2000 Sam Creasey (sammy@oh.verio.com) + + 02/01/2000 Initial modifications for parisc by Helge Deller (deller@gmx.de) + 03/02/2000 changes for better/correct(?) cache-flushing (deller) +*/ + +/* 82596.c: A generic 82596 ethernet driver for linux. */ +/* + Based on Apricot.c + Written 1994 by Mark Evans. + This driver is for the Apricot 82596 bus-master interface + + Modularised 12/94 Mark Evans + + + Modified to support the 82596 ethernet chips on 680x0 VME boards. + by Richard Hirst <richard@sleepie.demon.co.uk> + Renamed to be 82596.c + + 980825: Changed to receive directly in to sk_buffs which are + allocated at open() time. Eliminates copy on incoming frames + (small ones are still copied). Shared data now held in a + non-cached page, so we can run on 68060 in copyback mode. + + TBD: + * look at deferring rx frames rather than discarding (as per tulip) + * handle tx ring full as per tulip + * performace test to tune rx_copybreak + + Most of my modifications relate to the braindead big-endian + implementation by Intel. When the i596 is operating in + 'big-endian' mode, it thinks a 32 bit value of 0x12345678 + should be stored as 0x56781234. This is a real pain, when + you have linked lists which are shared by the 680x0 and the + i596. + + Driver skeleton + Written 1993 by Donald Becker. + Copyright 1993 United States Government as represented by the Director, + National Security Agency. This software may only be used and distributed + according to the terms of the GNU General Public License as modified by SRC, + incorporated herein by reference. + + The author may be reached as becker@scyld.com, or C/O + Scyld Computing Corporation, 410 Severn Ave., Suite 210, Annapolis MD 21403 + + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/errno.h> +#include <linux/ioport.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/init.h> +#include <linux/types.h> +#include <linux/bitops.h> +#include <linux/dma-mapping.h> +#include <linux/io.h> +#include <linux/irq.h> + +/* DEBUG flags + */ + +#define DEB_INIT 0x0001 +#define DEB_PROBE 0x0002 +#define DEB_SERIOUS 0x0004 +#define DEB_ERRORS 0x0008 +#define DEB_MULTI 0x0010 +#define DEB_TDR 0x0020 +#define DEB_OPEN 0x0040 +#define DEB_RESET 0x0080 +#define DEB_ADDCMD 0x0100 +#define DEB_STATUS 0x0200 +#define DEB_STARTTX 0x0400 +#define DEB_RXADDR 0x0800 +#define DEB_TXADDR 0x1000 +#define DEB_RXFRAME 0x2000 +#define DEB_INTS 0x4000 +#define DEB_STRUCT 0x8000 +#define DEB_ANY 0xffff + + +#define DEB(x, y) if (i596_debug & (x)) { y; } + + +/* + * The MPU_PORT command allows direct access to the 82596. With PORT access + * the following commands are available (p5-18). The 32-bit port command + * must be word-swapped with the most significant word written first. + * This only applies to VME boards. + */ +#define PORT_RESET 0x00 /* reset 82596 */ +#define PORT_SELFTEST 0x01 /* selftest */ +#define PORT_ALTSCP 0x02 /* alternate SCB address */ +#define PORT_ALTDUMP 0x03 /* Alternate DUMP address */ + +static int i596_debug = (DEB_SERIOUS|DEB_PROBE); + +/* Copy frames shorter than rx_copybreak, otherwise pass on up in + * a full sized sk_buff. Value of 100 stolen from tulip.c (!alpha). + */ +static int rx_copybreak = 100; + +#define PKT_BUF_SZ 1536 +#define MAX_MC_CNT 64 + +#define ISCP_BUSY 0x0001 + +#define I596_NULL ((u32)0xffffffff) + +#define CMD_EOL 0x8000 /* The last command of the list, stop. */ +#define CMD_SUSP 0x4000 /* Suspend after doing cmd. */ +#define CMD_INTR 0x2000 /* Interrupt after doing cmd. */ + +#define CMD_FLEX 0x0008 /* Enable flexible memory model */ + +enum commands { + CmdNOp = 0, CmdSASetup = 1, CmdConfigure = 2, CmdMulticastList = 3, + CmdTx = 4, CmdTDR = 5, CmdDump = 6, CmdDiagnose = 7 +}; + +#define STAT_C 0x8000 /* Set to 0 after execution */ +#define STAT_B 0x4000 /* Command being executed */ +#define STAT_OK 0x2000 /* Command executed ok */ +#define STAT_A 0x1000 /* Command aborted */ + +#define CUC_START 0x0100 +#define CUC_RESUME 0x0200 +#define CUC_SUSPEND 0x0300 +#define CUC_ABORT 0x0400 +#define RX_START 0x0010 +#define RX_RESUME 0x0020 +#define RX_SUSPEND 0x0030 +#define RX_ABORT 0x0040 + +#define TX_TIMEOUT 5 + + +struct i596_reg { + unsigned short porthi; + unsigned short portlo; + u32 ca; +}; + +#define EOF 0x8000 +#define SIZE_MASK 0x3fff + +struct i596_tbd { + unsigned short size; + unsigned short pad; + dma_addr_t next; + dma_addr_t data; + u32 cache_pad[5]; /* Total 32 bytes... */ +}; + +/* The command structure has two 'next' pointers; v_next is the address of + * the next command as seen by the CPU, b_next is the address of the next + * command as seen by the 82596. The b_next pointer, as used by the 82596 + * always references the status field of the next command, rather than the + * v_next field, because the 82596 is unaware of v_next. It may seem more + * logical to put v_next at the end of the structure, but we cannot do that + * because the 82596 expects other fields to be there, depending on command + * type. + */ + +struct i596_cmd { + struct i596_cmd *v_next; /* Address from CPUs viewpoint */ + unsigned short status; + unsigned short command; + dma_addr_t b_next; /* Address from i596 viewpoint */ +}; + +struct tx_cmd { + struct i596_cmd cmd; + dma_addr_t tbd; + unsigned short size; + unsigned short pad; + struct sk_buff *skb; /* So we can free it after tx */ + dma_addr_t dma_addr; +#ifdef __LP64__ + u32 cache_pad[6]; /* Total 64 bytes... */ +#else + u32 cache_pad[1]; /* Total 32 bytes... */ +#endif +}; + +struct tdr_cmd { + struct i596_cmd cmd; + unsigned short status; + unsigned short pad; +}; + +struct mc_cmd { + struct i596_cmd cmd; + short mc_cnt; + char mc_addrs[MAX_MC_CNT*6]; +}; + +struct sa_cmd { + struct i596_cmd cmd; + char eth_addr[8]; +}; + +struct cf_cmd { + struct i596_cmd cmd; + char i596_config[16]; +}; + +struct i596_rfd { + unsigned short stat; + unsigned short cmd; + dma_addr_t b_next; /* Address from i596 viewpoint */ + dma_addr_t rbd; + unsigned short count; + unsigned short size; + struct i596_rfd *v_next; /* Address from CPUs viewpoint */ + struct i596_rfd *v_prev; +#ifndef __LP64__ + u32 cache_pad[2]; /* Total 32 bytes... */ +#endif +}; + +struct i596_rbd { + /* hardware data */ + unsigned short count; + unsigned short zero1; + dma_addr_t b_next; + dma_addr_t b_data; /* Address from i596 viewpoint */ + unsigned short size; + unsigned short zero2; + /* driver data */ + struct sk_buff *skb; + struct i596_rbd *v_next; + dma_addr_t b_addr; /* This rbd addr from i596 view */ + unsigned char *v_data; /* Address from CPUs viewpoint */ + /* Total 32 bytes... */ +#ifdef __LP64__ + u32 cache_pad[4]; +#endif +}; + +/* These values as chosen so struct i596_dma fits in one page... */ + +#define TX_RING_SIZE 32 +#define RX_RING_SIZE 16 + +struct i596_scb { + unsigned short status; + unsigned short command; + dma_addr_t cmd; + dma_addr_t rfd; + u32 crc_err; + u32 align_err; + u32 resource_err; + u32 over_err; + u32 rcvdt_err; + u32 short_err; + unsigned short t_on; + unsigned short t_off; +}; + +struct i596_iscp { + u32 stat; + dma_addr_t scb; +}; + +struct i596_scp { + u32 sysbus; + u32 pad; + dma_addr_t iscp; +}; + +struct i596_dma { + struct i596_scp scp __attribute__((aligned(32))); + volatile struct i596_iscp iscp __attribute__((aligned(32))); + volatile struct i596_scb scb __attribute__((aligned(32))); + struct sa_cmd sa_cmd __attribute__((aligned(32))); + struct cf_cmd cf_cmd __attribute__((aligned(32))); + struct tdr_cmd tdr_cmd __attribute__((aligned(32))); + struct mc_cmd mc_cmd __attribute__((aligned(32))); + struct i596_rfd rfds[RX_RING_SIZE] __attribute__((aligned(32))); + struct i596_rbd rbds[RX_RING_SIZE] __attribute__((aligned(32))); + struct tx_cmd tx_cmds[TX_RING_SIZE] __attribute__((aligned(32))); + struct i596_tbd tbds[TX_RING_SIZE] __attribute__((aligned(32))); +}; + +struct i596_private { + struct i596_dma *dma; + u32 stat; + int last_restart; + struct i596_rfd *rfd_head; + struct i596_rbd *rbd_head; + struct i596_cmd *cmd_tail; + struct i596_cmd *cmd_head; + int cmd_backlog; + u32 last_cmd; + struct net_device_stats stats; + int next_tx_cmd; + int options; + spinlock_t lock; /* serialize access to chip */ + dma_addr_t dma_addr; + void __iomem *mpu_port; + void __iomem *ca; +}; + +static const char init_setup[] = +{ + 0x8E, /* length, prefetch on */ + 0xC8, /* fifo to 8, monitor off */ + 0x80, /* don't save bad frames */ + 0x2E, /* No source address insertion, 8 byte preamble */ + 0x00, /* priority and backoff defaults */ + 0x60, /* interframe spacing */ + 0x00, /* slot time LSB */ + 0xf2, /* slot time and retries */ + 0x00, /* promiscuous mode */ + 0x00, /* collision detect */ + 0x40, /* minimum frame length */ + 0xff, + 0x00, + 0x7f /* *multi IA */ }; + +static int i596_open(struct net_device *dev); +static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev); +static irqreturn_t i596_interrupt(int irq, void *dev_id); +static int i596_close(struct net_device *dev); +static struct net_device_stats *i596_get_stats(struct net_device *dev); +static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd); +static void i596_tx_timeout (struct net_device *dev); +static void print_eth(unsigned char *buf, char *str); +static void set_multicast_list(struct net_device *dev); +static inline void ca(struct net_device *dev); +static void mpu_port(struct net_device *dev, int c, dma_addr_t x); + +static int rx_ring_size = RX_RING_SIZE; +static int ticks_limit = 100; +static int max_cmd_backlog = TX_RING_SIZE-1; + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void i596_poll_controller(struct net_device *dev); +#endif + + +static inline int wait_istat(struct net_device *dev, struct i596_dma *dma, int delcnt, char *str) +{ + DMA_INV(dev, &(dma->iscp), sizeof(struct i596_iscp)); + while (--delcnt && dma->iscp.stat) { + udelay(10); + DMA_INV(dev, &(dma->iscp), sizeof(struct i596_iscp)); + } + if (!delcnt) { + printk(KERN_ERR "%s: %s, iscp.stat %04x, didn't clear\n", + dev->name, str, SWAP16(dma->iscp.stat)); + return -1; + } else + return 0; +} + + +static inline int wait_cmd(struct net_device *dev, struct i596_dma *dma, int delcnt, char *str) +{ + DMA_INV(dev, &(dma->scb), sizeof(struct i596_scb)); + while (--delcnt && dma->scb.command) { + udelay(10); + DMA_INV(dev, &(dma->scb), sizeof(struct i596_scb)); + } + if (!delcnt) { + printk(KERN_ERR "%s: %s, status %4.4x, cmd %4.4x.\n", + dev->name, str, + SWAP16(dma->scb.status), + SWAP16(dma->scb.command)); + return -1; + } else + return 0; +} + + +static void i596_display_data(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + struct i596_cmd *cmd; + struct i596_rfd *rfd; + struct i596_rbd *rbd; + + printk(KERN_DEBUG "lp and scp at %p, .sysbus = %08x, .iscp = %08x\n", + &dma->scp, dma->scp.sysbus, SWAP32(dma->scp.iscp)); + printk(KERN_DEBUG "iscp at %p, iscp.stat = %08x, .scb = %08x\n", + &dma->iscp, SWAP32(dma->iscp.stat), SWAP32(dma->iscp.scb)); + printk(KERN_DEBUG "scb at %p, scb.status = %04x, .command = %04x," + " .cmd = %08x, .rfd = %08x\n", + &dma->scb, SWAP16(dma->scb.status), SWAP16(dma->scb.command), + SWAP16(dma->scb.cmd), SWAP32(dma->scb.rfd)); + printk(KERN_DEBUG " errors: crc %x, align %x, resource %x," + " over %x, rcvdt %x, short %x\n", + SWAP32(dma->scb.crc_err), SWAP32(dma->scb.align_err), + SWAP32(dma->scb.resource_err), SWAP32(dma->scb.over_err), + SWAP32(dma->scb.rcvdt_err), SWAP32(dma->scb.short_err)); + cmd = lp->cmd_head; + while (cmd != NULL) { + printk(KERN_DEBUG + "cmd at %p, .status = %04x, .command = %04x," + " .b_next = %08x\n", + cmd, SWAP16(cmd->status), SWAP16(cmd->command), + SWAP32(cmd->b_next)); + cmd = cmd->v_next; + } + rfd = lp->rfd_head; + printk(KERN_DEBUG "rfd_head = %p\n", rfd); + do { + printk(KERN_DEBUG + " %p .stat %04x, .cmd %04x, b_next %08x, rbd %08x," + " count %04x\n", + rfd, SWAP16(rfd->stat), SWAP16(rfd->cmd), + SWAP32(rfd->b_next), SWAP32(rfd->rbd), + SWAP16(rfd->count)); + rfd = rfd->v_next; + } while (rfd != lp->rfd_head); + rbd = lp->rbd_head; + printk(KERN_DEBUG "rbd_head = %p\n", rbd); + do { + printk(KERN_DEBUG + " %p .count %04x, b_next %08x, b_data %08x," + " size %04x\n", + rbd, SWAP16(rbd->count), SWAP32(rbd->b_next), + SWAP32(rbd->b_data), SWAP16(rbd->size)); + rbd = rbd->v_next; + } while (rbd != lp->rbd_head); + DMA_INV(dev, dma, sizeof(struct i596_dma)); +} + + +#define virt_to_dma(lp, v) ((lp)->dma_addr + (dma_addr_t)((unsigned long)(v)-(unsigned long)((lp)->dma))) + +static inline int init_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int i; + struct i596_rfd *rfd; + struct i596_rbd *rbd; + + /* First build the Receive Buffer Descriptor List */ + + for (i = 0, rbd = dma->rbds; i < rx_ring_size; i++, rbd++) { + dma_addr_t dma_addr; + struct sk_buff *skb = netdev_alloc_skb(dev, PKT_BUF_SZ + 4); + + if (skb == NULL) + return -1; + skb_reserve(skb, 2); + dma_addr = dma_map_single(dev->dev.parent, skb->data, + PKT_BUF_SZ, DMA_FROM_DEVICE); + rbd->v_next = rbd+1; + rbd->b_next = SWAP32(virt_to_dma(lp, rbd+1)); + rbd->b_addr = SWAP32(virt_to_dma(lp, rbd)); + rbd->skb = skb; + rbd->v_data = skb->data; + rbd->b_data = SWAP32(dma_addr); + rbd->size = SWAP16(PKT_BUF_SZ); + } + lp->rbd_head = dma->rbds; + rbd = dma->rbds + rx_ring_size - 1; + rbd->v_next = dma->rbds; + rbd->b_next = SWAP32(virt_to_dma(lp, dma->rbds)); + + /* Now build the Receive Frame Descriptor List */ + + for (i = 0, rfd = dma->rfds; i < rx_ring_size; i++, rfd++) { + rfd->rbd = I596_NULL; + rfd->v_next = rfd+1; + rfd->v_prev = rfd-1; + rfd->b_next = SWAP32(virt_to_dma(lp, rfd+1)); + rfd->cmd = SWAP16(CMD_FLEX); + } + lp->rfd_head = dma->rfds; + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + rfd = dma->rfds; + rfd->rbd = SWAP32(virt_to_dma(lp, lp->rbd_head)); + rfd->v_prev = dma->rfds + rx_ring_size - 1; + rfd = dma->rfds + rx_ring_size - 1; + rfd->v_next = dma->rfds; + rfd->b_next = SWAP32(virt_to_dma(lp, dma->rfds)); + rfd->cmd = SWAP16(CMD_EOL|CMD_FLEX); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); + return 0; +} + +static inline void remove_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_rbd *rbd; + int i; + + for (i = 0, rbd = lp->dma->rbds; i < rx_ring_size; i++, rbd++) { + if (rbd->skb == NULL) + break; + dma_unmap_single(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + dev_kfree_skb(rbd->skb); + } +} + + +static void rebuild_rx_bufs(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int i; + + /* Ensure rx frame/buffer descriptors are tidy */ + + for (i = 0; i < rx_ring_size; i++) { + dma->rfds[i].rbd = I596_NULL; + dma->rfds[i].cmd = SWAP16(CMD_FLEX); + } + dma->rfds[rx_ring_size-1].cmd = SWAP16(CMD_EOL|CMD_FLEX); + lp->rfd_head = dma->rfds; + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + lp->rbd_head = dma->rbds; + dma->rfds[0].rbd = SWAP32(virt_to_dma(lp, dma->rbds)); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); +} + + +static int init_i596_mem(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + unsigned long flags; + + mpu_port(dev, PORT_RESET, 0); + udelay(100); /* Wait 100us - seems to help */ + + /* change the scp address */ + + lp->last_cmd = jiffies; + + dma->scp.sysbus = SYSBUS; + dma->scp.iscp = SWAP32(virt_to_dma(lp, &(dma->iscp))); + dma->iscp.scb = SWAP32(virt_to_dma(lp, &(dma->scb))); + dma->iscp.stat = SWAP32(ISCP_BUSY); + lp->cmd_backlog = 0; + + lp->cmd_head = NULL; + dma->scb.cmd = I596_NULL; + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: starting i82596.\n", dev->name)); + + DMA_WBACK(dev, &(dma->scp), sizeof(struct i596_scp)); + DMA_WBACK(dev, &(dma->iscp), sizeof(struct i596_iscp)); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + mpu_port(dev, PORT_ALTSCP, virt_to_dma(lp, &dma->scp)); + ca(dev); + if (wait_istat(dev, dma, 1000, "initialization timed out")) + goto failed; + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: i82596 initialization successful\n", + dev->name)); + + if (request_irq(dev->irq, &i596_interrupt, 0, "i82596", dev)) { + printk(KERN_ERR "%s: IRQ %d not free\n", dev->name, dev->irq); + goto failed; + } + + /* Ensure rx frame/buffer descriptors are tidy */ + rebuild_rx_bufs(dev); + + dma->scb.command = 0; + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: queuing CmdConfigure\n", dev->name)); + memcpy(dma->cf_cmd.i596_config, init_setup, 14); + dma->cf_cmd.cmd.command = SWAP16(CmdConfigure); + DMA_WBACK(dev, &(dma->cf_cmd), sizeof(struct cf_cmd)); + i596_add_cmd(dev, &dma->cf_cmd.cmd); + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: queuing CmdSASetup\n", dev->name)); + memcpy(dma->sa_cmd.eth_addr, dev->dev_addr, 6); + dma->sa_cmd.cmd.command = SWAP16(CmdSASetup); + DMA_WBACK(dev, &(dma->sa_cmd), sizeof(struct sa_cmd)); + i596_add_cmd(dev, &dma->sa_cmd.cmd); + + DEB(DEB_INIT, printk(KERN_DEBUG "%s: queuing CmdTDR\n", dev->name)); + dma->tdr_cmd.cmd.command = SWAP16(CmdTDR); + DMA_WBACK(dev, &(dma->tdr_cmd), sizeof(struct tdr_cmd)); + i596_add_cmd(dev, &dma->tdr_cmd.cmd); + + spin_lock_irqsave (&lp->lock, flags); + + if (wait_cmd(dev, dma, 1000, "timed out waiting to issue RX_START")) { + spin_unlock_irqrestore (&lp->lock, flags); + goto failed_free_irq; + } + DEB(DEB_INIT, printk(KERN_DEBUG "%s: Issuing RX_START\n", dev->name)); + dma->scb.command = SWAP16(RX_START); + dma->scb.rfd = SWAP32(virt_to_dma(lp, dma->rfds)); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + + ca(dev); + + spin_unlock_irqrestore (&lp->lock, flags); + if (wait_cmd(dev, dma, 1000, "RX_START not processed")) + goto failed_free_irq; + DEB(DEB_INIT, printk(KERN_DEBUG + "%s: Receive unit started OK\n", dev->name)); + return 0; + +failed_free_irq: + free_irq(dev->irq, dev); +failed: + printk(KERN_ERR "%s: Failed to initialise 82596\n", dev->name); + mpu_port(dev, PORT_RESET, 0); + return -1; +} + + +static inline int i596_rx(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_rfd *rfd; + struct i596_rbd *rbd; + int frames = 0; + + DEB(DEB_RXFRAME, printk(KERN_DEBUG + "i596_rx(), rfd_head %p, rbd_head %p\n", + lp->rfd_head, lp->rbd_head)); + + + rfd = lp->rfd_head; /* Ref next frame to check */ + + DMA_INV(dev, rfd, sizeof(struct i596_rfd)); + while (rfd->stat & SWAP16(STAT_C)) { /* Loop while complete frames */ + if (rfd->rbd == I596_NULL) + rbd = NULL; + else if (rfd->rbd == lp->rbd_head->b_addr) { + rbd = lp->rbd_head; + DMA_INV(dev, rbd, sizeof(struct i596_rbd)); + } else { + printk(KERN_ERR "%s: rbd chain broken!\n", dev->name); + /* XXX Now what? */ + rbd = NULL; + } + DEB(DEB_RXFRAME, printk(KERN_DEBUG + " rfd %p, rfd.rbd %08x, rfd.stat %04x\n", + rfd, rfd->rbd, rfd->stat)); + + if (rbd != NULL && (rfd->stat & SWAP16(STAT_OK))) { + /* a good frame */ + int pkt_len = SWAP16(rbd->count) & 0x3fff; + struct sk_buff *skb = rbd->skb; + int rx_in_place = 0; + + DEB(DEB_RXADDR, print_eth(rbd->v_data, "received")); + frames++; + + /* Check if the packet is long enough to just accept + * without copying to a properly sized skbuff. + */ + + if (pkt_len > rx_copybreak) { + struct sk_buff *newskb; + dma_addr_t dma_addr; + + dma_unmap_single(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + /* Get fresh skbuff to replace filled one. */ + newskb = netdev_alloc_skb(dev, PKT_BUF_SZ + 4); + if (newskb == NULL) { + skb = NULL; /* drop pkt */ + goto memory_squeeze; + } + skb_reserve(newskb, 2); + + /* Pass up the skb already on the Rx ring. */ + skb_put(skb, pkt_len); + rx_in_place = 1; + rbd->skb = newskb; + dma_addr = dma_map_single(dev->dev.parent, + newskb->data, + PKT_BUF_SZ, + DMA_FROM_DEVICE); + rbd->v_data = newskb->data; + rbd->b_data = SWAP32(dma_addr); + DMA_WBACK_INV(dev, rbd, sizeof(struct i596_rbd)); + } else + skb = netdev_alloc_skb(dev, pkt_len + 2); +memory_squeeze: + if (skb == NULL) { + /* XXX tulip.c can defer packets here!! */ + printk(KERN_ERR + "%s: i596_rx Memory squeeze, dropping packet.\n", + dev->name); + lp->stats.rx_dropped++; + } else { + if (!rx_in_place) { + /* 16 byte align the data fields */ + dma_sync_single_for_cpu(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + skb_reserve(skb, 2); + memcpy(skb_put(skb, pkt_len), rbd->v_data, pkt_len); + dma_sync_single_for_device(dev->dev.parent, + (dma_addr_t)SWAP32(rbd->b_data), + PKT_BUF_SZ, DMA_FROM_DEVICE); + } + skb->len = pkt_len; + skb->protocol = eth_type_trans(skb, dev); + netif_rx(skb); + dev->last_rx = jiffies; + lp->stats.rx_packets++; + lp->stats.rx_bytes += pkt_len; + } + } else { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: Error, rfd.stat = 0x%04x\n", + dev->name, rfd->stat)); + lp->stats.rx_errors++; + if (rfd->stat & SWAP16(0x0100)) + lp->stats.collisions++; + if (rfd->stat & SWAP16(0x8000)) + lp->stats.rx_length_errors++; + if (rfd->stat & SWAP16(0x0001)) + lp->stats.rx_over_errors++; + if (rfd->stat & SWAP16(0x0002)) + lp->stats.rx_fifo_errors++; + if (rfd->stat & SWAP16(0x0004)) + lp->stats.rx_frame_errors++; + if (rfd->stat & SWAP16(0x0008)) + lp->stats.rx_crc_errors++; + if (rfd->stat & SWAP16(0x0010)) + lp->stats.rx_length_errors++; + } + + /* Clear the buffer descriptor count and EOF + F flags */ + + if (rbd != NULL && (rbd->count & SWAP16(0x4000))) { + rbd->count = 0; + lp->rbd_head = rbd->v_next; + DMA_WBACK_INV(dev, rbd, sizeof(struct i596_rbd)); + } + + /* Tidy the frame descriptor, marking it as end of list */ + + rfd->rbd = I596_NULL; + rfd->stat = 0; + rfd->cmd = SWAP16(CMD_EOL|CMD_FLEX); + rfd->count = 0; + + /* Update record of next frame descriptor to process */ + + lp->dma->scb.rfd = rfd->b_next; + lp->rfd_head = rfd->v_next; + DMA_WBACK_INV(dev, rfd, sizeof(struct i596_rfd)); + + /* Remove end-of-list from old end descriptor */ + + rfd->v_prev->cmd = SWAP16(CMD_FLEX); + DMA_WBACK_INV(dev, rfd->v_prev, sizeof(struct i596_rfd)); + rfd = lp->rfd_head; + DMA_INV(dev, rfd, sizeof(struct i596_rfd)); + } + + DEB(DEB_RXFRAME, printk(KERN_DEBUG "frames %d\n", frames)); + + return 0; +} + + +static inline void i596_cleanup_cmd(struct net_device *dev, struct i596_private *lp) +{ + struct i596_cmd *ptr; + + while (lp->cmd_head != NULL) { + ptr = lp->cmd_head; + lp->cmd_head = ptr->v_next; + lp->cmd_backlog--; + + switch (SWAP16(ptr->command) & 0x7) { + case CmdTx: + { + struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; + struct sk_buff *skb = tx_cmd->skb; + dma_unmap_single(dev->dev.parent, + tx_cmd->dma_addr, + skb->len, DMA_TO_DEVICE); + + dev_kfree_skb(skb); + + lp->stats.tx_errors++; + lp->stats.tx_aborted_errors++; + + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + tx_cmd->cmd.command = 0; /* Mark as free */ + break; + } + default: + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + } + DMA_WBACK_INV(dev, ptr, sizeof(struct i596_cmd)); + } + + wait_cmd(dev, lp->dma, 100, "i596_cleanup_cmd timed out"); + lp->dma->scb.cmd = I596_NULL; + DMA_WBACK(dev, &(lp->dma->scb), sizeof(struct i596_scb)); +} + + +static inline void i596_reset(struct net_device *dev, struct i596_private *lp) +{ + unsigned long flags; + + DEB(DEB_RESET, printk(KERN_DEBUG "i596_reset\n")); + + spin_lock_irqsave (&lp->lock, flags); + + wait_cmd(dev, lp->dma, 100, "i596_reset timed out"); + + netif_stop_queue(dev); + + /* FIXME: this command might cause an lpmc */ + lp->dma->scb.command = SWAP16(CUC_ABORT | RX_ABORT); + DMA_WBACK(dev, &(lp->dma->scb), sizeof(struct i596_scb)); + ca(dev); + + /* wait for shutdown */ + wait_cmd(dev, lp->dma, 1000, "i596_reset 2 timed out"); + spin_unlock_irqrestore (&lp->lock, flags); + + i596_cleanup_cmd(dev, lp); + i596_rx(dev); + + netif_start_queue(dev); + init_i596_mem(dev); +} + + +static void i596_add_cmd(struct net_device *dev, struct i596_cmd *cmd) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + unsigned long flags; + + DEB(DEB_ADDCMD, printk(KERN_DEBUG "i596_add_cmd cmd_head %p\n", + lp->cmd_head)); + + cmd->status = 0; + cmd->command |= SWAP16(CMD_EOL | CMD_INTR); + cmd->v_next = NULL; + cmd->b_next = I596_NULL; + DMA_WBACK(dev, cmd, sizeof(struct i596_cmd)); + + spin_lock_irqsave (&lp->lock, flags); + + if (lp->cmd_head != NULL) { + lp->cmd_tail->v_next = cmd; + lp->cmd_tail->b_next = SWAP32(virt_to_dma(lp, &cmd->status)); + DMA_WBACK(dev, lp->cmd_tail, sizeof(struct i596_cmd)); + } else { + lp->cmd_head = cmd; + wait_cmd(dev, dma, 100, "i596_add_cmd timed out"); + dma->scb.cmd = SWAP32(virt_to_dma(lp, &cmd->status)); + dma->scb.command = SWAP16(CUC_START); + DMA_WBACK(dev, &(dma->scb), sizeof(struct i596_scb)); + ca(dev); + } + lp->cmd_tail = cmd; + lp->cmd_backlog++; + + spin_unlock_irqrestore (&lp->lock, flags); + + if (lp->cmd_backlog > max_cmd_backlog) { + unsigned long tickssofar = jiffies - lp->last_cmd; + + if (tickssofar < ticks_limit) + return; + + printk(KERN_ERR + "%s: command unit timed out, status resetting.\n", + dev->name); +#if 1 + i596_reset(dev, lp); +#endif + } +} + +static int i596_open(struct net_device *dev) +{ + DEB(DEB_OPEN, printk(KERN_DEBUG + "%s: i596_open() irq %d.\n", dev->name, dev->irq)); + + if (init_rx_bufs(dev)) { + printk(KERN_ERR "%s: Failed to init rx bufs\n", dev->name); + return -EAGAIN; + } + if (init_i596_mem(dev)) { + printk(KERN_ERR "%s: Failed to init memory\n", dev->name); + goto out_remove_rx_bufs; + } + netif_start_queue(dev); + + return 0; + +out_remove_rx_bufs: + remove_rx_bufs(dev); + return -EAGAIN; +} + +static void i596_tx_timeout (struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + + /* Transmitter timeout, serious problems. */ + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: transmit timed out, status resetting.\n", + dev->name)); + + lp->stats.tx_errors++; + + /* Try to restart the adaptor */ + if (lp->last_restart == lp->stats.tx_packets) { + DEB(DEB_ERRORS, printk(KERN_DEBUG "Resetting board.\n")); + /* Shutdown and restart */ + i596_reset (dev, lp); + } else { + /* Issue a channel attention signal */ + DEB(DEB_ERRORS, printk(KERN_DEBUG "Kicking board.\n")); + lp->dma->scb.command = SWAP16(CUC_START | RX_START); + DMA_WBACK_INV(dev, &(lp->dma->scb), sizeof(struct i596_scb)); + ca (dev); + lp->last_restart = lp->stats.tx_packets; + } + + dev->trans_start = jiffies; + netif_wake_queue (dev); +} + + +static int i596_start_xmit(struct sk_buff *skb, struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct tx_cmd *tx_cmd; + struct i596_tbd *tbd; + short length = skb->len; + dev->trans_start = jiffies; + + DEB(DEB_STARTTX, printk(KERN_DEBUG + "%s: i596_start_xmit(%x,%p) called\n", + dev->name, skb->len, skb->data)); + + if (length < ETH_ZLEN) { + if (skb_padto(skb, ETH_ZLEN)) + return 0; + length = ETH_ZLEN; + } + + netif_stop_queue(dev); + + tx_cmd = lp->dma->tx_cmds + lp->next_tx_cmd; + tbd = lp->dma->tbds + lp->next_tx_cmd; + + if (tx_cmd->cmd.command) { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: xmit ring full, dropping packet.\n", + dev->name)); + lp->stats.tx_dropped++; + + dev_kfree_skb(skb); + } else { + if (++lp->next_tx_cmd == TX_RING_SIZE) + lp->next_tx_cmd = 0; + tx_cmd->tbd = SWAP32(virt_to_dma(lp, tbd)); + tbd->next = I596_NULL; + + tx_cmd->cmd.command = SWAP16(CMD_FLEX | CmdTx); + tx_cmd->skb = skb; + + tx_cmd->pad = 0; + tx_cmd->size = 0; + tbd->pad = 0; + tbd->size = SWAP16(EOF | length); + + tx_cmd->dma_addr = dma_map_single(dev->dev.parent, skb->data, + skb->len, DMA_TO_DEVICE); + tbd->data = SWAP32(tx_cmd->dma_addr); + + DEB(DEB_TXADDR, print_eth(skb->data, "tx-queued")); + DMA_WBACK_INV(dev, tx_cmd, sizeof(struct tx_cmd)); + DMA_WBACK_INV(dev, tbd, sizeof(struct i596_tbd)); + i596_add_cmd(dev, &tx_cmd->cmd); + + lp->stats.tx_packets++; + lp->stats.tx_bytes += length; + } + + netif_start_queue(dev); + + return 0; +} + +static void print_eth(unsigned char *add, char *str) +{ + int i; + + printk(KERN_DEBUG "i596 0x%p, ", add); + for (i = 0; i < 6; i++) + printk(" %02X", add[i + 6]); + printk(" -->"); + for (i = 0; i < 6; i++) + printk(" %02X", add[i]); + printk(" %02X%02X, %s\n", add[12], add[13], str); +} + +static int __devinit i82596_probe(struct net_device *dev) +{ + int i; + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma; + + /* This lot is ensure things have been cache line aligned. */ + BUILD_BUG_ON(sizeof(struct i596_rfd) != 32); + BUILD_BUG_ON(sizeof(struct i596_rbd) & 31); + BUILD_BUG_ON(sizeof(struct tx_cmd) & 31); + BUILD_BUG_ON(sizeof(struct i596_tbd) != 32); +#ifndef __LP64__ + BUILD_BUG_ON(sizeof(struct i596_dma) > 4096); +#endif + + if (!dev->base_addr || !dev->irq) + return -ENODEV; + + dma = (struct i596_dma *) DMA_ALLOC(dev->dev.parent, + sizeof(struct i596_dma), &lp->dma_addr, GFP_KERNEL); + if (!dma) { + printk(KERN_ERR "%s: Couldn't get shared memory\n", __FILE__); + return -ENOMEM; + } + + /* The 82596-specific entries in the device structure. */ + dev->open = i596_open; + dev->stop = i596_close; + dev->hard_start_xmit = i596_start_xmit; + dev->get_stats = i596_get_stats; + dev->set_multicast_list = set_multicast_list; + dev->tx_timeout = i596_tx_timeout; + dev->watchdog_timeo = TX_TIMEOUT; +#ifdef CONFIG_NET_POLL_CONTROLLER + dev->poll_controller = i596_poll_controller; +#endif + + memset(dma, 0, sizeof(struct i596_dma)); + lp->dma = dma; + + dma->scb.command = 0; + dma->scb.cmd = I596_NULL; + dma->scb.rfd = I596_NULL; + spin_lock_init(&lp->lock); + + DMA_WBACK_INV(dev, dma, sizeof(struct i596_dma)); + + i = register_netdev(dev); + if (i) { + DMA_FREE(dev->dev.parent, sizeof(struct i596_dma), + (void *)dma, lp->dma_addr); + return i; + }; + + DEB(DEB_PROBE, printk(KERN_INFO "%s: 82596 at %#3lx,", + dev->name, dev->base_addr)); + for (i = 0; i < 6; i++) + DEB(DEB_PROBE, printk(" %2.2X", dev->dev_addr[i])); + DEB(DEB_PROBE, printk(" IRQ %d.\n", dev->irq)); + DEB(DEB_INIT, printk(KERN_INFO + "%s: dma at 0x%p (%d bytes), lp->scb at 0x%p\n", + dev->name, dma, (int)sizeof(struct i596_dma), + &dma->scb)); + + return 0; +} + +#ifdef CONFIG_NET_POLL_CONTROLLER +static void i596_poll_controller(struct net_device *dev) +{ + disable_irq(dev->irq); + i596_interrupt(dev->irq, dev); + enable_irq(dev->irq); +} +#endif + +static irqreturn_t i596_interrupt(int irq, void *dev_id) +{ + struct net_device *dev = dev_id; + struct i596_private *lp; + struct i596_dma *dma; + unsigned short status, ack_cmd = 0; + + if (dev == NULL) { + printk(KERN_WARNING "%s: irq %d for unknown device.\n", + __FUNCTION__, irq); + return IRQ_NONE; + } + + lp = netdev_priv(dev); + dma = lp->dma; + + spin_lock (&lp->lock); + + wait_cmd(dev, dma, 100, "i596 interrupt, timeout"); + status = SWAP16(dma->scb.status); + + DEB(DEB_INTS, printk(KERN_DEBUG + "%s: i596 interrupt, IRQ %d, status %4.4x.\n", + dev->name, irq, status)); + + ack_cmd = status & 0xf000; + + if (!ack_cmd) { + DEB(DEB_ERRORS, printk(KERN_DEBUG + "%s: interrupt with no events\n", + dev->name)); + spin_unlock (&lp->lock); + return IRQ_NONE; + } + + if ((status & 0x8000) || (status & 0x2000)) { + struct i596_cmd *ptr; + + if ((status & 0x8000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt completed command.\n", + dev->name)); + if ((status & 0x2000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt command unit inactive %x.\n", + dev->name, status & 0x0700)); + + while (lp->cmd_head != NULL) { + DMA_INV(dev, lp->cmd_head, sizeof(struct i596_cmd)); + if (!(lp->cmd_head->status & SWAP16(STAT_C))) + break; + + ptr = lp->cmd_head; + + DEB(DEB_STATUS, + printk(KERN_DEBUG + "cmd_head->status = %04x, ->command = %04x\n", + SWAP16(lp->cmd_head->status), + SWAP16(lp->cmd_head->command))); + lp->cmd_head = ptr->v_next; + lp->cmd_backlog--; + + switch (SWAP16(ptr->command) & 0x7) { + case CmdTx: + { + struct tx_cmd *tx_cmd = (struct tx_cmd *) ptr; + struct sk_buff *skb = tx_cmd->skb; + + if (ptr->status & SWAP16(STAT_OK)) { + DEB(DEB_TXADDR, + print_eth(skb->data, "tx-done")); + } else { + lp->stats.tx_errors++; + if (ptr->status & SWAP16(0x0020)) + lp->stats.collisions++; + if (!(ptr->status & SWAP16(0x0040))) + lp->stats.tx_heartbeat_errors++; + if (ptr->status & SWAP16(0x0400)) + lp->stats.tx_carrier_errors++; + if (ptr->status & SWAP16(0x0800)) + lp->stats.collisions++; + if (ptr->status & SWAP16(0x1000)) + lp->stats.tx_aborted_errors++; + } + dma_unmap_single(dev->dev.parent, + tx_cmd->dma_addr, + skb->len, DMA_TO_DEVICE); + dev_kfree_skb_irq(skb); + + tx_cmd->cmd.command = 0; /* Mark free */ + break; + } + case CmdTDR: + { + unsigned short status = SWAP16(((struct tdr_cmd *)ptr)->status); + + if (status & 0x8000) { + DEB(DEB_ANY, + printk(KERN_DEBUG "%s: link ok.\n", + dev->name)); + } else { + if (status & 0x4000) + printk(KERN_ERR + "%s: Transceiver problem.\n", + dev->name); + if (status & 0x2000) + printk(KERN_ERR + "%s: Termination problem.\n", + dev->name); + if (status & 0x1000) + printk(KERN_ERR + "%s: Short circuit.\n", + dev->name); + + DEB(DEB_TDR, + printk(KERN_DEBUG "%s: Time %d.\n", + dev->name, status & 0x07ff)); + } + break; + } + case CmdConfigure: + /* + * Zap command so set_multicast_list() know + * it is free + */ + ptr->command = 0; + break; + } + ptr->v_next = NULL; + ptr->b_next = I596_NULL; + DMA_WBACK(dev, ptr, sizeof(struct i596_cmd)); + lp->last_cmd = jiffies; + } + + /* This mess is arranging that only the last of any outstanding + * commands has the interrupt bit set. Should probably really + * only add to the cmd queue when the CU is stopped. + */ + ptr = lp->cmd_head; + while ((ptr != NULL) && (ptr != lp->cmd_tail)) { + struct i596_cmd *prev = ptr; + + ptr->command &= SWAP16(0x1fff); + ptr = ptr->v_next; + DMA_WBACK_INV(dev, prev, sizeof(struct i596_cmd)); + } + + if (lp->cmd_head != NULL) + ack_cmd |= CUC_START; + dma->scb.cmd = SWAP32(virt_to_dma(lp, &lp->cmd_head->status)); + DMA_WBACK_INV(dev, &dma->scb, sizeof(struct i596_scb)); + } + if ((status & 0x1000) || (status & 0x4000)) { + if ((status & 0x4000)) + DEB(DEB_INTS, + printk(KERN_DEBUG + "%s: i596 interrupt received a frame.\n", + dev->name)); + i596_rx(dev); + /* Only RX_START if stopped - RGH 07-07-96 */ + if (status & 0x1000) { + if (netif_running(dev)) { + DEB(DEB_ERRORS, + printk(KERN_DEBUG + "%s: i596 interrupt receive unit inactive, status 0x%x\n", + dev->name, status)); + ack_cmd |= RX_START; + lp->stats.rx_errors++; + lp->stats.rx_fifo_errors++; + rebuild_rx_bufs(dev); + } + } + } + wait_cmd(dev, dma, 100, "i596 interrupt, timeout"); + dma->scb.command = SWAP16(ack_cmd); + DMA_WBACK(dev, &dma->scb, sizeof(struct i596_scb)); + + /* DANGER: I suspect that some kind of interrupt + acknowledgement aside from acking the 82596 might be needed + here... but it's running acceptably without */ + + ca(dev); + + wait_cmd(dev, dma, 100, "i596 interrupt, exit timeout"); + DEB(DEB_INTS, printk(KERN_DEBUG "%s: exiting interrupt.\n", dev->name)); + + spin_unlock (&lp->lock); + return IRQ_HANDLED; +} + +static int i596_close(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + unsigned long flags; + + netif_stop_queue(dev); + + DEB(DEB_INIT, + printk(KERN_DEBUG + "%s: Shutting down ethercard, status was %4.4x.\n", + dev->name, SWAP16(lp->dma->scb.status))); + + spin_lock_irqsave(&lp->lock, flags); + + wait_cmd(dev, lp->dma, 100, "close1 timed out"); + lp->dma->scb.command = SWAP16(CUC_ABORT | RX_ABORT); + DMA_WBACK(dev, &lp->dma->scb, sizeof(struct i596_scb)); + + ca(dev); + + wait_cmd(dev, lp->dma, 100, "close2 timed out"); + spin_unlock_irqrestore(&lp->lock, flags); + DEB(DEB_STRUCT, i596_display_data(dev)); + i596_cleanup_cmd(dev, lp); + + free_irq(dev->irq, dev); + remove_rx_bufs(dev); + + return 0; +} + +static struct net_device_stats *i596_get_stats(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + + return &lp->stats; +} + +/* + * Set or clear the multicast filter for this adaptor. + */ + +static void set_multicast_list(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + struct i596_dma *dma = lp->dma; + int config = 0, cnt; + + DEB(DEB_MULTI, + printk(KERN_DEBUG + "%s: set multicast list, %d entries, promisc %s, allmulti %s\n", + dev->name, dev->mc_count, + dev->flags & IFF_PROMISC ? "ON" : "OFF", + dev->flags & IFF_ALLMULTI ? "ON" : "OFF")); + + if ((dev->flags & IFF_PROMISC) && + !(dma->cf_cmd.i596_config[8] & 0x01)) { + dma->cf_cmd.i596_config[8] |= 0x01; + config = 1; + } + if (!(dev->flags & IFF_PROMISC) && + (dma->cf_cmd.i596_config[8] & 0x01)) { + dma->cf_cmd.i596_config[8] &= ~0x01; + config = 1; + } + if ((dev->flags & IFF_ALLMULTI) && + (dma->cf_cmd.i596_config[11] & 0x20)) { + dma->cf_cmd.i596_config[11] &= ~0x20; + config = 1; + } + if (!(dev->flags & IFF_ALLMULTI) && + !(dma->cf_cmd.i596_config[11] & 0x20)) { + dma->cf_cmd.i596_config[11] |= 0x20; + config = 1; + } + if (config) { + if (dma->cf_cmd.cmd.command) + printk(KERN_INFO + "%s: config change request already queued\n", + dev->name); + else { + dma->cf_cmd.cmd.command = SWAP16(CmdConfigure); + DMA_WBACK_INV(dev, &dma->cf_cmd, sizeof(struct cf_cmd)); + i596_add_cmd(dev, &dma->cf_cmd.cmd); + } + } + + cnt = dev->mc_count; + if (cnt > MAX_MC_CNT) { + cnt = MAX_MC_CNT; + printk(KERN_NOTICE "%s: Only %d multicast addresses supported", + dev->name, cnt); + } + + if (dev->mc_count > 0) { + struct dev_mc_list *dmi; + unsigned char *cp; + struct mc_cmd *cmd; + + cmd = &dma->mc_cmd; + cmd->cmd.command = SWAP16(CmdMulticastList); + cmd->mc_cnt = SWAP16(dev->mc_count * 6); + cp = cmd->mc_addrs; + for (dmi = dev->mc_list; + cnt && dmi != NULL; + dmi = dmi->next, cnt--, cp += 6) { + memcpy(cp, dmi->dmi_addr, 6); + if (i596_debug > 1) + DEB(DEB_MULTI, + printk(KERN_DEBUG + "%s: Adding address %02x:%02x:%02x:%02x:%02x:%02x\n", + dev->name, cp[0], cp[1], cp[2], cp[3], cp[4], cp[5])); + } + DMA_WBACK_INV(dev, &dma->mc_cmd, sizeof(struct mc_cmd)); + i596_add_cmd(dev, &cmd->cmd); + } +} diff --git a/drivers/net/mlx4/qp.c b/drivers/net/mlx4/qp.c index 7f8b7d55b6e..492cfaaaa75 100644 --- a/drivers/net/mlx4/qp.c +++ b/drivers/net/mlx4/qp.c @@ -113,8 +113,7 @@ int mlx4_qp_modify(struct mlx4_dev *dev, struct mlx4_mtt *mtt, struct mlx4_cmd_mailbox *mailbox; int ret = 0; - if (cur_state < 0 || cur_state >= MLX4_QP_NUM_STATE || - new_state < 0 || cur_state >= MLX4_QP_NUM_STATE || + if (cur_state >= MLX4_QP_NUM_STATE || cur_state >= MLX4_QP_NUM_STATE || !op[cur_state][new_state]) return -EINVAL; diff --git a/drivers/net/netxen/netxen_nic_niu.c b/drivers/net/netxen/netxen_nic_niu.c index 75102d30730..05e0577a0e1 100644 --- a/drivers/net/netxen/netxen_nic_niu.c +++ b/drivers/net/netxen/netxen_nic_niu.c @@ -724,7 +724,7 @@ int netxen_niu_disable_gbe_port(struct netxen_adapter *adapter) __u32 mac_cfg0; u32 port = physical_port[adapter->portnum]; - if ((port < 0) || (port > NETXEN_NIU_MAX_GBE_PORTS)) + if (port > NETXEN_NIU_MAX_GBE_PORTS) return -EINVAL; mac_cfg0 = 0; netxen_gb_soft_reset(mac_cfg0); @@ -757,7 +757,7 @@ int netxen_niu_set_promiscuous_mode(struct netxen_adapter *adapter, __u32 reg; u32 port = physical_port[adapter->portnum]; - if ((port < 0) || (port > NETXEN_NIU_MAX_GBE_PORTS)) + if (port > NETXEN_NIU_MAX_GBE_PORTS) return -EINVAL; /* save previous contents */ @@ -894,7 +894,7 @@ int netxen_niu_xg_set_promiscuous_mode(struct netxen_adapter *adapter, __u32 reg; u32 port = physical_port[adapter->portnum]; - if ((port < 0) || (port > NETXEN_NIU_MAX_XG_PORTS)) + if (port > NETXEN_NIU_MAX_XG_PORTS) return -EINVAL; if (netxen_nic_hw_read_wx(adapter, diff --git a/drivers/net/pasemi_mac.c b/drivers/net/pasemi_mac.c index 8d38425e46c..0b3066a6fe4 100644 --- a/drivers/net/pasemi_mac.c +++ b/drivers/net/pasemi_mac.c @@ -755,7 +755,7 @@ static int pasemi_mac_open(struct net_device *dev) flags |= PAS_MAC_CFG_PCFG_TSR_1G | PAS_MAC_CFG_PCFG_SPD_1G; pci_write_config_dword(mac->iob_pdev, PAS_IOB_DMA_RXCH_CFG(mac->dma_rxch), - PAS_IOB_DMA_RXCH_CFG_CNTTH(1)); + PAS_IOB_DMA_RXCH_CFG_CNTTH(0)); pci_write_config_dword(mac->iob_pdev, PAS_IOB_DMA_TXCH_CFG(mac->dma_txch), PAS_IOB_DMA_TXCH_CFG_CNTTH(32)); diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c index 808fae1577e..50dff1b81d3 100644 --- a/drivers/net/pcmcia/axnet_cs.c +++ b/drivers/net/pcmcia/axnet_cs.c @@ -521,6 +521,7 @@ static void mdio_write(kio_addr_t addr, int phy_id, int loc, int value) static int axnet_open(struct net_device *dev) { + int ret; axnet_dev_t *info = PRIV(dev); struct pcmcia_device *link = info->p_dev; @@ -529,9 +530,11 @@ static int axnet_open(struct net_device *dev) if (!pcmcia_dev_present(link)) return -ENODEV; - link->open++; + ret = request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, "axnet_cs", dev); + if (ret) + return ret; - request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, "axnet_cs", dev); + link->open++; info->link_status = 0x00; init_timer(&info->watchdog); diff --git a/drivers/net/pcmcia/fmvj18x_cs.c b/drivers/net/pcmcia/fmvj18x_cs.c index 3f93d493323..85d5f2ca4bb 100644 --- a/drivers/net/pcmcia/fmvj18x_cs.c +++ b/drivers/net/pcmcia/fmvj18x_cs.c @@ -109,7 +109,7 @@ static const struct ethtool_ops netdev_ethtool_ops; card type */ typedef enum { MBH10302, MBH10304, TDK, CONTEC, LA501, UNGERMANN, - XXX10304 + XXX10304, NEC, KME } cardtype_t; /* @@ -374,6 +374,18 @@ static int fmvj18x_config(struct pcmcia_device *link) link->io.NumPorts2 = 8; } break; + case MANFID_NEC: + cardtype = NEC; /* MultiFunction Card */ + link->conf.ConfigBase = 0x800; + link->conf.ConfigIndex = 0x47; + link->io.NumPorts2 = 8; + break; + case MANFID_KME: + cardtype = KME; /* MultiFunction Card */ + link->conf.ConfigBase = 0x800; + link->conf.ConfigIndex = 0x47; + link->io.NumPorts2 = 8; + break; case MANFID_CONTEC: cardtype = CONTEC; break; @@ -450,6 +462,8 @@ static int fmvj18x_config(struct pcmcia_device *link) case TDK: case LA501: case CONTEC: + case NEC: + case KME: tuple.DesiredTuple = CISTPL_FUNCE; tuple.TupleOffset = 0; CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); @@ -469,6 +483,10 @@ static int fmvj18x_config(struct pcmcia_device *link) card_name = "TDK LAK-CD021"; } else if( cardtype == LA501 ) { card_name = "LA501"; + } else if( cardtype == NEC ) { + card_name = "PK-UG-J001"; + } else if( cardtype == KME ) { + card_name = "Panasonic"; } else { card_name = "C-NET(PC)C"; } @@ -678,8 +696,11 @@ static struct pcmcia_device_id fmvj18x_ids[] = { PCMCIA_DEVICE_PROD_ID1("PCMCIA MBH10302", 0x8f4005da), PCMCIA_DEVICE_PROD_ID1("UBKK,V2.0", 0x90888080), PCMCIA_PFC_DEVICE_PROD_ID12(0, "TDK", "GlobalNetworker 3410/3412", 0x1eae9475, 0xd9a93bed), + PCMCIA_PFC_DEVICE_PROD_ID12(0, "NEC", "PK-UG-J001" ,0x18df0ba0 ,0x831b1064), PCMCIA_PFC_DEVICE_MANF_CARD(0, 0x0105, 0x0d0a), PCMCIA_PFC_DEVICE_MANF_CARD(0, 0x0105, 0x0e0a), + PCMCIA_PFC_DEVICE_MANF_CARD(0, 0x0032, 0x0a05), + PCMCIA_PFC_DEVICE_MANF_CARD(0, 0x0032, 0x1101), PCMCIA_DEVICE_NULL, }; MODULE_DEVICE_TABLE(pcmcia, fmvj18x_ids); diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c index d88e9b2e93c..f2613c29b00 100644 --- a/drivers/net/pcmcia/pcnet_cs.c +++ b/drivers/net/pcmcia/pcnet_cs.c @@ -960,6 +960,7 @@ static void mii_phy_probe(struct net_device *dev) static int pcnet_open(struct net_device *dev) { + int ret; pcnet_dev_t *info = PRIV(dev); struct pcmcia_device *link = info->p_dev; @@ -968,10 +969,12 @@ static int pcnet_open(struct net_device *dev) if (!pcmcia_dev_present(link)) return -ENODEV; - link->open++; - set_misc_reg(dev); - request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, dev_info, dev); + ret = request_irq(dev->irq, ei_irq_wrapper, IRQF_SHARED, dev_info, dev); + if (ret) + return ret; + + link->open++; info->phy_id = info->eth_phy; info->link_status = 0x00; @@ -1552,6 +1555,7 @@ static struct pcmcia_device_id pcnet_ids[] = { PCMCIA_PFC_DEVICE_PROD_ID12(0, "Grey Cell", "GCS3000", 0x2a151fac, 0x48b932ae), PCMCIA_PFC_DEVICE_PROD_ID12(0, "Linksys", "EtherFast 10&100 + 56K PC Card (PCMLM56)", 0x0733cc81, 0xb3765033), PCMCIA_PFC_DEVICE_PROD_ID12(0, "LINKSYS", "PCMLM336", 0xf7cb0b07, 0x7a821b58), + PCMCIA_PFC_DEVICE_PROD_ID12(0, "MICRO RESEARCH", "COMBO-L/M-336", 0xb2ced065, 0x3ced0555), PCMCIA_PFC_DEVICE_PROD_ID12(0, "PCMCIAs", "ComboCard", 0xdcfe12d3, 0xcd8906cc), PCMCIA_PFC_DEVICE_PROD_ID12(0, "PCMCIAs", "LanModem", 0xdcfe12d3, 0xc67c648f), PCMCIA_MFC_DEVICE_PROD_ID12(0, "IBM", "Home and Away 28.8 PC Card ", 0xb569a6e5, 0x5bd4ff2c), diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index 09b6f259eb9..dd09011c7ee 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -55,6 +55,11 @@ config BROADCOM_PHY ---help--- Currently supports the BCM5411, BCM5421 and BCM5461 PHYs. +config ICPLUS_PHY + tristate "Drivers for ICPlus PHYs" + ---help--- + Currently supports the IP175C PHY. + config FIXED_PHY tristate "Drivers for PHY emulation on fixed speed/link" ---help--- diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile index bcd1efbd2a1..8885650647f 100644 --- a/drivers/net/phy/Makefile +++ b/drivers/net/phy/Makefile @@ -11,4 +11,5 @@ obj-$(CONFIG_QSEMI_PHY) += qsemi.o obj-$(CONFIG_SMSC_PHY) += smsc.o obj-$(CONFIG_VITESSE_PHY) += vitesse.o obj-$(CONFIG_BROADCOM_PHY) += broadcom.o +obj-$(CONFIG_ICPLUS_PHY) += icplus.o obj-$(CONFIG_FIXED_PHY) += fixed.o diff --git a/drivers/net/phy/icplus.c b/drivers/net/phy/icplus.c new file mode 100644 index 00000000000..af3f1f2a9f8 --- /dev/null +++ b/drivers/net/phy/icplus.c @@ -0,0 +1,134 @@ +/* + * Driver for ICPlus PHYs + * + * Copyright (c) 2007 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + * + */ +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/errno.h> +#include <linux/unistd.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/spinlock.h> +#include <linux/mm.h> +#include <linux/module.h> +#include <linux/mii.h> +#include <linux/ethtool.h> +#include <linux/phy.h> + +#include <asm/io.h> +#include <asm/irq.h> +#include <asm/uaccess.h> + +MODULE_DESCRIPTION("ICPlus IP175C PHY driver"); +MODULE_AUTHOR("Michael Barkowski"); +MODULE_LICENSE("GPL"); + +static int ip175c_config_init(struct phy_device *phydev) +{ + int err, i; + static int full_reset_performed = 0; + + if (full_reset_performed == 0) { + + /* master reset */ + err = phydev->bus->write(phydev->bus, 30, 0, 0x175c); + if (err < 0) + return err; + + /* ensure no bus delays overlap reset period */ + err = phydev->bus->read(phydev->bus, 30, 0); + + /* data sheet specifies reset period is 2 msec */ + mdelay(2); + + /* enable IP175C mode */ + err = phydev->bus->write(phydev->bus, 29, 31, 0x175c); + if (err < 0) + return err; + + /* Set MII0 speed and duplex (in PHY mode) */ + err = phydev->bus->write(phydev->bus, 29, 22, 0x420); + if (err < 0) + return err; + + /* reset switch ports */ + for (i = 0; i < 5; i++) { + err = phydev->bus->write(phydev->bus, i, + MII_BMCR, BMCR_RESET); + if (err < 0) + return err; + } + + for (i = 0; i < 5; i++) + err = phydev->bus->read(phydev->bus, i, MII_BMCR); + + mdelay(2); + + full_reset_performed = 1; + } + + if (phydev->addr != 4) { + phydev->state = PHY_RUNNING; + phydev->speed = SPEED_100; + phydev->duplex = DUPLEX_FULL; + phydev->link = 1; + netif_carrier_on(phydev->attached_dev); + } + + return 0; +} + +static int ip175c_read_status(struct phy_device *phydev) +{ + if (phydev->addr == 4) /* WAN port */ + genphy_read_status(phydev); + else + /* Don't need to read status for switch ports */ + phydev->irq = PHY_IGNORE_INTERRUPT; + + return 0; +} + +static int ip175c_config_aneg(struct phy_device *phydev) +{ + if (phydev->addr == 4) /* WAN port */ + genphy_config_aneg(phydev); + + return 0; +} + +static struct phy_driver ip175c_driver = { + .phy_id = 0x02430d80, + .name = "ICPlus IP175C", + .phy_id_mask = 0x0ffffff0, + .features = PHY_BASIC_FEATURES, + .config_init = &ip175c_config_init, + .config_aneg = &ip175c_config_aneg, + .read_status = &ip175c_read_status, + .driver = { .owner = THIS_MODULE,}, +}; + +static int __init ip175c_init(void) +{ + return phy_driver_register(&ip175c_driver); +} + +static void __exit ip175c_exit(void) +{ + phy_driver_unregister(&ip175c_driver); +} + +module_init(ip175c_init); +module_exit(ip175c_exit); diff --git a/drivers/net/phy/marvell.c b/drivers/net/phy/marvell.c index b87f8d2a888..fbe1104e9a0 100644 --- a/drivers/net/phy/marvell.c +++ b/drivers/net/phy/marvell.c @@ -60,6 +60,7 @@ #define MII_M1111_PHY_EXT_SR 0x1b #define MII_M1111_HWCFG_MODE_MASK 0xf #define MII_M1111_HWCFG_MODE_RGMII 0xb +#define MII_M1111_HWCFG_MODE_SGMII_NO_CLK 0x4 MODULE_DESCRIPTION("Marvell PHY driver"); MODULE_AUTHOR("Andy Fleming"); @@ -169,6 +170,21 @@ static int m88e1111_config_init(struct phy_device *phydev) return err; } + if (phydev->interface == PHY_INTERFACE_MODE_SGMII) { + int temp; + + temp = phy_read(phydev, MII_M1111_PHY_EXT_SR); + if (temp < 0) + return temp; + + temp &= ~(MII_M1111_HWCFG_MODE_MASK); + temp |= MII_M1111_HWCFG_MODE_SGMII_NO_CLK; + + err = phy_write(phydev, MII_M1111_PHY_EXT_SR, temp); + if (err < 0) + return err; + } + err = phy_write(phydev, MII_BMCR, BMCR_RESET); if (err < 0) return err; diff --git a/drivers/net/qla3xxx.c b/drivers/net/qla3xxx.c index 585be044ebb..8be8be451ad 100755 --- a/drivers/net/qla3xxx.c +++ b/drivers/net/qla3xxx.c @@ -2433,37 +2433,22 @@ static int ql_get_seg_count(struct ql3_adapter *qdev, return -1; } -static void ql_hw_csum_setup(struct sk_buff *skb, +static void ql_hw_csum_setup(const struct sk_buff *skb, struct ob_mac_iocb_req *mac_iocb_ptr) { - struct ethhdr *eth; - struct iphdr *ip = NULL; - u8 offset = ETH_HLEN; + const struct iphdr *ip = ip_hdr(skb); - eth = (struct ethhdr *)(skb->data); + mac_iocb_ptr->ip_hdr_off = skb_network_offset(skb); + mac_iocb_ptr->ip_hdr_len = ip->ihl; - if (eth->h_proto == __constant_htons(ETH_P_IP)) { - ip = (struct iphdr *)&skb->data[ETH_HLEN]; - } else if (eth->h_proto == htons(ETH_P_8021Q) && - ((struct vlan_ethhdr *)skb->data)-> - h_vlan_encapsulated_proto == __constant_htons(ETH_P_IP)) { - ip = (struct iphdr *)&skb->data[VLAN_ETH_HLEN]; - offset = VLAN_ETH_HLEN; - } - - if (ip) { - if (ip->protocol == IPPROTO_TCP) { - mac_iocb_ptr->flags1 |= OB_3032MAC_IOCB_REQ_TC | + if (ip->protocol == IPPROTO_TCP) { + mac_iocb_ptr->flags1 |= OB_3032MAC_IOCB_REQ_TC | OB_3032MAC_IOCB_REQ_IC; - mac_iocb_ptr->ip_hdr_off = offset; - mac_iocb_ptr->ip_hdr_len = ip->ihl; - } else if (ip->protocol == IPPROTO_UDP) { - mac_iocb_ptr->flags1 |= OB_3032MAC_IOCB_REQ_UC | + } else { + mac_iocb_ptr->flags1 |= OB_3032MAC_IOCB_REQ_UC | OB_3032MAC_IOCB_REQ_IC; - mac_iocb_ptr->ip_hdr_off = offset; - mac_iocb_ptr->ip_hdr_len = ip->ihl; - } } + } /* diff --git a/drivers/net/r8169.c b/drivers/net/r8169.c index 5ec7752caa4..982a9010c7a 100644 --- a/drivers/net/r8169.c +++ b/drivers/net/r8169.c @@ -1,53 +1,11 @@ /* -========================================================================= - r8169.c: A RealTek RTL-8169 Gigabit Ethernet driver for Linux kernel 2.4.x. - -------------------------------------------------------------------- - - History: - Feb 4 2002 - created initially by ShuChen <shuchen@realtek.com.tw>. - May 20 2002 - Add link status force-mode and TBI mode support. - 2004 - Massive updates. See kernel SCM system for details. -========================================================================= - 1. [DEPRECATED: use ethtool instead] The media can be forced in 5 modes. - Command: 'insmod r8169 media = SET_MEDIA' - Ex: 'insmod r8169 media = 0x04' will force PHY to operate in 100Mpbs Half-duplex. - - SET_MEDIA can be: - _10_Half = 0x01 - _10_Full = 0x02 - _100_Half = 0x04 - _100_Full = 0x08 - _1000_Full = 0x10 - - 2. Support TBI mode. -========================================================================= -VERSION 1.1 <2002/10/4> - - The bit4:0 of MII register 4 is called "selector field", and have to be - 00001b to indicate support of IEEE std 802.3 during NWay process of - exchanging Link Code Word (FLP). - -VERSION 1.2 <2002/11/30> - - - Large style cleanup - - Use ether_crc in stock kernel (linux/crc32.h) - - Copy mc_filter setup code from 8139cp - (includes an optimization, and avoids set_bit use) - -VERSION 1.6LK <2004/04/14> - - - Merge of Realtek's version 1.6 - - Conversion to DMA API - - Suspend/resume - - Endianness - - Misc Rx/Tx bugs - -VERSION 2.2LK <2005/01/25> - - - RX csum, TX csum/SG, TSO - - VLAN - - baby (< 7200) Jumbo frames support - - Merge of Realtek's version 2.2 (new phy) + * r8169.c: RealTek 8169/8168/8101 ethernet driver. + * + * Copyright (c) 2002 ShuChen <shuchen@realtek.com.tw> + * Copyright (c) 2003 - 2007 Francois Romieu <romieu@fr.zoreil.com> + * Copyright (c) a lot of people too. Please respect their work. + * + * See MAINTAINERS file for support contact information. */ #include <linux/module.h> @@ -108,11 +66,6 @@ VERSION 2.2LK <2005/01/25> #define rtl8169_rx_quota(count, quota) count #endif -/* media options */ -#define MAX_UNITS 8 -static int media[MAX_UNITS] = { -1, -1, -1, -1, -1, -1, -1, -1 }; -static int num_media = 0; - /* Maximum events (Rx packets, etc.) to handle at each interrupt. */ static const int max_interrupt_work = 20; @@ -126,7 +79,7 @@ static const int multicast_filter_limit = 32; #define RX_FIFO_THRESH 7 /* 7 means NO threshold, Rx buffer level before first PCI xfer. */ #define RX_DMA_BURST 6 /* Maximum PCI burst, '6' is 1024 */ #define TX_DMA_BURST 6 /* Maximum PCI burst, '6' is 1024 */ -#define EarlyTxThld 0x3F /* 0x3F means NO early transmit */ +#define EarlyTxThld 0x3F /* 0x3F means NO early transmit */ #define RxPacketMaxSize 0x3FE8 /* 16K - 1 - ETH_HLEN - VLAN - CRC... */ #define SafeMtu 0x1c20 /* ... actually life sucks beyond ~7k */ #define InterFrameGap 0x03 /* 3 means InterFrameGap = the shortest one */ @@ -151,16 +104,17 @@ static const int multicast_filter_limit = 32; #define RTL_R32(reg) ((unsigned long) readl (ioaddr + (reg))) enum mac_version { - RTL_GIGA_MAC_VER_01 = 0x00, - RTL_GIGA_MAC_VER_02 = 0x01, - RTL_GIGA_MAC_VER_03 = 0x02, - RTL_GIGA_MAC_VER_04 = 0x03, - RTL_GIGA_MAC_VER_05 = 0x04, - RTL_GIGA_MAC_VER_11 = 0x0b, - RTL_GIGA_MAC_VER_12 = 0x0c, - RTL_GIGA_MAC_VER_13 = 0x0d, - RTL_GIGA_MAC_VER_14 = 0x0e, - RTL_GIGA_MAC_VER_15 = 0x0f + RTL_GIGA_MAC_VER_01 = 0x01, // 8169 + RTL_GIGA_MAC_VER_02 = 0x02, // 8169S + RTL_GIGA_MAC_VER_03 = 0x03, // 8110S + RTL_GIGA_MAC_VER_04 = 0x04, // 8169SB + RTL_GIGA_MAC_VER_05 = 0x05, // 8110SCd + RTL_GIGA_MAC_VER_06 = 0x06, // 8110SCe + RTL_GIGA_MAC_VER_11 = 0x0b, // 8168Bb + RTL_GIGA_MAC_VER_12 = 0x0c, // 8168Be 8168Bf + RTL_GIGA_MAC_VER_13 = 0x0d, // 8101Eb 8101Ec + RTL_GIGA_MAC_VER_14 = 0x0e, // 8101 + RTL_GIGA_MAC_VER_15 = 0x0f // 8101 }; enum phy_version { @@ -180,11 +134,12 @@ static const struct { u8 mac_version; u32 RxConfigMask; /* Clears the bits supported by this chip */ } rtl_chip_info[] = { - _R("RTL8169", RTL_GIGA_MAC_VER_01, 0xff7e1880), - _R("RTL8169s/8110s", RTL_GIGA_MAC_VER_02, 0xff7e1880), - _R("RTL8169s/8110s", RTL_GIGA_MAC_VER_03, 0xff7e1880), - _R("RTL8169sb/8110sb", RTL_GIGA_MAC_VER_04, 0xff7e1880), - _R("RTL8169sc/8110sc", RTL_GIGA_MAC_VER_05, 0xff7e1880), + _R("RTL8169", RTL_GIGA_MAC_VER_01, 0xff7e1880), // 8169 + _R("RTL8169s", RTL_GIGA_MAC_VER_02, 0xff7e1880), // 8169S + _R("RTL8110s", RTL_GIGA_MAC_VER_03, 0xff7e1880), // 8110S + _R("RTL8169sb/8110sb", RTL_GIGA_MAC_VER_04, 0xff7e1880), // 8169SB + _R("RTL8169sc/8110sc", RTL_GIGA_MAC_VER_05, 0xff7e1880), // 8110SCd + _R("RTL8169sc/8110sc", RTL_GIGA_MAC_VER_06, 0xff7e1880), // 8110SCe _R("RTL8168b/8111b", RTL_GIGA_MAC_VER_11, 0xff7e1880), // PCI-E _R("RTL8168b/8111b", RTL_GIGA_MAC_VER_12, 0xff7e1880), // PCI-E _R("RTL8101e", RTL_GIGA_MAC_VER_13, 0xff7e1880), // PCI-E 8139 @@ -199,20 +154,15 @@ enum cfg_version { RTL_CFG_2 }; -static const struct { - unsigned int region; - unsigned int align; -} rtl_cfg_info[] = { - [RTL_CFG_0] = { 1, NET_IP_ALIGN }, - [RTL_CFG_1] = { 2, NET_IP_ALIGN }, - [RTL_CFG_2] = { 2, 8 } -}; +static void rtl_hw_start_8169(struct net_device *); +static void rtl_hw_start_8168(struct net_device *); +static void rtl_hw_start_8101(struct net_device *); static struct pci_device_id rtl8169_pci_tbl[] = { { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8129), 0, 0, RTL_CFG_0 }, { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8136), 0, 0, RTL_CFG_2 }, { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8167), 0, 0, RTL_CFG_0 }, - { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8168), 0, 0, RTL_CFG_2 }, + { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8168), 0, 0, RTL_CFG_1 }, { PCI_DEVICE(PCI_VENDOR_ID_REALTEK, 0x8169), 0, 0, RTL_CFG_0 }, { PCI_DEVICE(PCI_VENDOR_ID_DLINK, 0x4300), 0, 0, RTL_CFG_0 }, { PCI_DEVICE(0x1259, 0xc107), 0, 0, RTL_CFG_0 }, @@ -230,62 +180,63 @@ static struct { u32 msg_enable; } debug = { -1 }; -enum RTL8169_registers { - MAC0 = 0, /* Ethernet hardware address. */ - MAR0 = 8, /* Multicast filter. */ - CounterAddrLow = 0x10, - CounterAddrHigh = 0x14, - TxDescStartAddrLow = 0x20, - TxDescStartAddrHigh = 0x24, - TxHDescStartAddrLow = 0x28, - TxHDescStartAddrHigh = 0x2c, - FLASH = 0x30, - ERSR = 0x36, - ChipCmd = 0x37, - TxPoll = 0x38, - IntrMask = 0x3C, - IntrStatus = 0x3E, - TxConfig = 0x40, - RxConfig = 0x44, - RxMissed = 0x4C, - Cfg9346 = 0x50, - Config0 = 0x51, - Config1 = 0x52, - Config2 = 0x53, - Config3 = 0x54, - Config4 = 0x55, - Config5 = 0x56, - MultiIntr = 0x5C, - PHYAR = 0x60, - TBICSR = 0x64, - TBI_ANAR = 0x68, - TBI_LPAR = 0x6A, - PHYstatus = 0x6C, - RxMaxSize = 0xDA, - CPlusCmd = 0xE0, - IntrMitigate = 0xE2, - RxDescAddrLow = 0xE4, - RxDescAddrHigh = 0xE8, - EarlyTxThres = 0xEC, - FuncEvent = 0xF0, - FuncEventMask = 0xF4, - FuncPresetState = 0xF8, - FuncForceEvent = 0xFC, +enum rtl_registers { + MAC0 = 0, /* Ethernet hardware address. */ + MAC4 = 4, + MAR0 = 8, /* Multicast filter. */ + CounterAddrLow = 0x10, + CounterAddrHigh = 0x14, + TxDescStartAddrLow = 0x20, + TxDescStartAddrHigh = 0x24, + TxHDescStartAddrLow = 0x28, + TxHDescStartAddrHigh = 0x2c, + FLASH = 0x30, + ERSR = 0x36, + ChipCmd = 0x37, + TxPoll = 0x38, + IntrMask = 0x3c, + IntrStatus = 0x3e, + TxConfig = 0x40, + RxConfig = 0x44, + RxMissed = 0x4c, + Cfg9346 = 0x50, + Config0 = 0x51, + Config1 = 0x52, + Config2 = 0x53, + Config3 = 0x54, + Config4 = 0x55, + Config5 = 0x56, + MultiIntr = 0x5c, + PHYAR = 0x60, + TBICSR = 0x64, + TBI_ANAR = 0x68, + TBI_LPAR = 0x6a, + PHYstatus = 0x6c, + RxMaxSize = 0xda, + CPlusCmd = 0xe0, + IntrMitigate = 0xe2, + RxDescAddrLow = 0xe4, + RxDescAddrHigh = 0xe8, + EarlyTxThres = 0xec, + FuncEvent = 0xf0, + FuncEventMask = 0xf4, + FuncPresetState = 0xf8, + FuncForceEvent = 0xfc, }; -enum RTL8169_register_content { +enum rtl_register_content { /* InterruptStatusBits */ - SYSErr = 0x8000, - PCSTimeout = 0x4000, - SWInt = 0x0100, - TxDescUnavail = 0x80, - RxFIFOOver = 0x40, - LinkChg = 0x20, - RxOverflow = 0x10, - TxErr = 0x08, - TxOK = 0x04, - RxErr = 0x02, - RxOK = 0x01, + SYSErr = 0x8000, + PCSTimeout = 0x4000, + SWInt = 0x0100, + TxDescUnavail = 0x0080, + RxFIFOOver = 0x0040, + LinkChg = 0x0020, + RxOverflow = 0x0010, + TxErr = 0x0008, + TxOK = 0x0004, + RxErr = 0x0002, + RxOK = 0x0001, /* RxStatusDesc */ RxFOVF = (1 << 23), @@ -295,26 +246,31 @@ enum RTL8169_register_content { RxCRC = (1 << 19), /* ChipCmdBits */ - CmdReset = 0x10, - CmdRxEnb = 0x08, - CmdTxEnb = 0x04, - RxBufEmpty = 0x01, + CmdReset = 0x10, + CmdRxEnb = 0x08, + CmdTxEnb = 0x04, + RxBufEmpty = 0x01, + + /* TXPoll register p.5 */ + HPQ = 0x80, /* Poll cmd on the high prio queue */ + NPQ = 0x40, /* Poll cmd on the low prio queue */ + FSWInt = 0x01, /* Forced software interrupt */ /* Cfg9346Bits */ - Cfg9346_Lock = 0x00, - Cfg9346_Unlock = 0xC0, + Cfg9346_Lock = 0x00, + Cfg9346_Unlock = 0xc0, /* rx_mode_bits */ - AcceptErr = 0x20, - AcceptRunt = 0x10, - AcceptBroadcast = 0x08, - AcceptMulticast = 0x04, - AcceptMyPhys = 0x02, - AcceptAllPhys = 0x01, + AcceptErr = 0x20, + AcceptRunt = 0x10, + AcceptBroadcast = 0x08, + AcceptMulticast = 0x04, + AcceptMyPhys = 0x02, + AcceptAllPhys = 0x01, /* RxConfigBits */ - RxCfgFIFOShift = 13, - RxCfgDMAShift = 8, + RxCfgFIFOShift = 13, + RxCfgDMAShift = 8, /* TxConfigBits */ TxInterFrameGapShift = 24, @@ -323,6 +279,10 @@ enum RTL8169_register_content { /* Config1 register p.24 */ PMEnable = (1 << 0), /* Power Management Enable */ + /* Config2 register p. 25 */ + PCI_Clock_66MHz = 0x01, + PCI_Clock_33MHz = 0x00, + /* Config3 register p.25 */ MagicPacket = (1 << 5), /* Wake up when receives a Magic Packet */ LinkUp = (1 << 4), /* Wake up when the cable connection is re-established */ @@ -343,36 +303,34 @@ enum RTL8169_register_content { TBINwComplete = 0x01000000, /* CPlusCmd p.31 */ + PktCntrDisable = (1 << 7), // 8168 RxVlan = (1 << 6), RxChkSum = (1 << 5), PCIDAC = (1 << 4), PCIMulRW = (1 << 3), + INTT_0 = 0x0000, // 8168 + INTT_1 = 0x0001, // 8168 + INTT_2 = 0x0002, // 8168 + INTT_3 = 0x0003, // 8168 /* rtl8169_PHYstatus */ - TBI_Enable = 0x80, - TxFlowCtrl = 0x40, - RxFlowCtrl = 0x20, - _1000bpsF = 0x10, - _100bps = 0x08, - _10bps = 0x04, - LinkStatus = 0x02, - FullDup = 0x01, - - /* _MediaType */ - _10_Half = 0x01, - _10_Full = 0x02, - _100_Half = 0x04, - _100_Full = 0x08, - _1000_Full = 0x10, + TBI_Enable = 0x80, + TxFlowCtrl = 0x40, + RxFlowCtrl = 0x20, + _1000bpsF = 0x10, + _100bps = 0x08, + _10bps = 0x04, + LinkStatus = 0x02, + FullDup = 0x01, /* _TBICSRBit */ - TBILinkOK = 0x02000000, + TBILinkOK = 0x02000000, /* DumpCounterCommand */ - CounterDump = 0x8, + CounterDump = 0x8, }; -enum _DescStatusBit { +enum desc_status_bit { DescOwn = (1 << 31), /* Descriptor is owned by NIC */ RingEnd = (1 << 30), /* End of descriptor ring */ FirstFrag = (1 << 29), /* First segment of a packet */ @@ -405,15 +363,15 @@ enum _DescStatusBit { #define RsvdMask 0x3fffc000 struct TxDesc { - u32 opts1; - u32 opts2; - u64 addr; + __le32 opts1; + __le32 opts2; + __le64 addr; }; struct RxDesc { - u32 opts1; - u32 opts2; - u64 addr; + __le32 opts1; + __le32 opts2; + __le64 addr; }; struct ring_info { @@ -446,6 +404,8 @@ struct rtl8169_private { unsigned rx_buf_sz; struct timer_list timer; u16 cp_cmd; + u16 intr_event; + u16 napi_event; u16 intr_mask; int phy_auto_nego_reg; int phy_1000_ctrl_reg; @@ -455,6 +415,7 @@ struct rtl8169_private { int (*set_speed)(struct net_device *, u8 autoneg, u16 speed, u8 duplex); void (*get_settings)(struct net_device *, struct ethtool_cmd *); void (*phy_reset_enable)(void __iomem *); + void (*hw_start)(struct net_device *); unsigned int (*phy_reset_pending)(void __iomem *); unsigned int (*link_ok)(void __iomem *); struct delayed_work task; @@ -463,8 +424,6 @@ struct rtl8169_private { MODULE_AUTHOR("Realtek and the Linux r8169 crew <netdev@vger.kernel.org>"); MODULE_DESCRIPTION("RealTek RTL-8169 Gigabit Ethernet driver"); -module_param_array(media, int, &num_media, 0); -MODULE_PARM_DESC(media, "force phy operation. Deprecated by ethtool (8)."); module_param(rx_copybreak, int, 0); MODULE_PARM_DESC(rx_copybreak, "Copy breakpoint for copy-only-tiny-frames"); module_param(use_dac, int, 0); @@ -478,9 +437,9 @@ static int rtl8169_open(struct net_device *dev); static int rtl8169_start_xmit(struct sk_buff *skb, struct net_device *dev); static irqreturn_t rtl8169_interrupt(int irq, void *dev_instance); static int rtl8169_init_ring(struct net_device *dev); -static void rtl8169_hw_start(struct net_device *dev); +static void rtl_hw_start(struct net_device *dev); static int rtl8169_close(struct net_device *dev); -static void rtl8169_set_rx_mode(struct net_device *dev); +static void rtl_set_rx_mode(struct net_device *dev); static void rtl8169_tx_timeout(struct net_device *dev); static struct net_device_stats *rtl8169_get_stats(struct net_device *dev); static int rtl8169_rx_interrupt(struct net_device *, struct rtl8169_private *, @@ -493,35 +452,37 @@ static void rtl8169_rx_clear(struct rtl8169_private *tp); static int rtl8169_poll(struct net_device *dev, int *budget); #endif -static const u16 rtl8169_intr_mask = - SYSErr | LinkChg | RxOverflow | RxFIFOOver | TxErr | TxOK | RxErr | RxOK; -static const u16 rtl8169_napi_event = - RxOK | RxOverflow | RxFIFOOver | TxOK | TxErr; static const unsigned int rtl8169_rx_config = (RX_FIFO_THRESH << RxCfgFIFOShift) | (RX_DMA_BURST << RxCfgDMAShift); -static void mdio_write(void __iomem *ioaddr, int RegAddr, int value) +static void mdio_write(void __iomem *ioaddr, int reg_addr, int value) { int i; - RTL_W32(PHYAR, 0x80000000 | (RegAddr & 0xFF) << 16 | value); + RTL_W32(PHYAR, 0x80000000 | (reg_addr & 0xFF) << 16 | value); for (i = 20; i > 0; i--) { - /* Check if the RTL8169 has completed writing to the specified MII register */ + /* + * Check if the RTL8169 has completed writing to the specified + * MII register. + */ if (!(RTL_R32(PHYAR) & 0x80000000)) break; udelay(25); } } -static int mdio_read(void __iomem *ioaddr, int RegAddr) +static int mdio_read(void __iomem *ioaddr, int reg_addr) { int i, value = -1; - RTL_W32(PHYAR, 0x0 | (RegAddr & 0xFF) << 16); + RTL_W32(PHYAR, 0x0 | (reg_addr & 0xFF) << 16); for (i = 20; i > 0; i--) { - /* Check if the RTL8169 has completed retrieving data from the specified MII register */ + /* + * Check if the RTL8169 has completed retrieving data from + * the specified MII register. + */ if (RTL_R32(PHYAR) & 0x80000000) { value = (int) (RTL_R32(PHYAR) & 0xFFFF); break; @@ -579,7 +540,8 @@ static void rtl8169_xmii_reset_enable(void __iomem *ioaddr) } static void rtl8169_check_link_status(struct net_device *dev, - struct rtl8169_private *tp, void __iomem *ioaddr) + struct rtl8169_private *tp, + void __iomem *ioaddr) { unsigned long flags; @@ -596,38 +558,6 @@ static void rtl8169_check_link_status(struct net_device *dev, spin_unlock_irqrestore(&tp->lock, flags); } -static void rtl8169_link_option(int idx, u8 *autoneg, u16 *speed, u8 *duplex) -{ - struct { - u16 speed; - u8 duplex; - u8 autoneg; - u8 media; - } link_settings[] = { - { SPEED_10, DUPLEX_HALF, AUTONEG_DISABLE, _10_Half }, - { SPEED_10, DUPLEX_FULL, AUTONEG_DISABLE, _10_Full }, - { SPEED_100, DUPLEX_HALF, AUTONEG_DISABLE, _100_Half }, - { SPEED_100, DUPLEX_FULL, AUTONEG_DISABLE, _100_Full }, - { SPEED_1000, DUPLEX_FULL, AUTONEG_DISABLE, _1000_Full }, - /* Make TBI happy */ - { SPEED_1000, DUPLEX_FULL, AUTONEG_ENABLE, 0xff } - }, *p; - unsigned char option; - - option = ((idx < MAX_UNITS) && (idx >= 0)) ? media[idx] : 0xff; - - if ((option != 0xff) && !idx && netif_msg_drv(&debug)) - printk(KERN_WARNING PFX "media option is deprecated.\n"); - - for (p = link_settings; p->media != 0xff; p++) { - if (p->media == option) - break; - } - *autoneg = p->autoneg; - *speed = p->speed; - *duplex = p->duplex; -} - static void rtl8169_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) { struct rtl8169_private *tp = netdev_priv(dev); @@ -667,7 +597,7 @@ static int rtl8169_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) { struct rtl8169_private *tp = netdev_priv(dev); void __iomem *ioaddr = tp->mmio_addr; - int i; + unsigned int i; static struct { u32 opt; u16 reg; @@ -893,8 +823,7 @@ static int rtl8169_rx_vlan_skb(struct rtl8169_private *tp, struct RxDesc *desc, int ret; if (tp->vlgrp && (opts2 & RxVlanTag)) { - rtl8169_rx_hwaccel_skb(skb, tp->vlgrp, - swab16(opts2 & 0xffff)); + rtl8169_rx_hwaccel_skb(skb, tp->vlgrp, swab16(opts2 & 0xffff)); ret = 0; } else ret = -1; @@ -1115,7 +1044,6 @@ static void rtl8169_get_strings(struct net_device *dev, u32 stringset, u8 *data) } } - static const struct ethtool_ops rtl8169_ethtool_ops = { .get_drvinfo = rtl8169_get_drvinfo, .get_regs_len = rtl8169_get_regs_len, @@ -1141,8 +1069,8 @@ static const struct ethtool_ops rtl8169_ethtool_ops = { .get_perm_addr = ethtool_op_get_perm_addr, }; -static void rtl8169_write_gmii_reg_bit(void __iomem *ioaddr, int reg, int bitnum, - int bitval) +static void rtl8169_write_gmii_reg_bit(void __iomem *ioaddr, int reg, + int bitnum, int bitval) { int val; @@ -1152,8 +1080,20 @@ static void rtl8169_write_gmii_reg_bit(void __iomem *ioaddr, int reg, int bitnum mdio_write(ioaddr, reg, val & 0xffff); } -static void rtl8169_get_mac_version(struct rtl8169_private *tp, void __iomem *ioaddr) +static void rtl8169_get_mac_version(struct rtl8169_private *tp, + void __iomem *ioaddr) { + /* + * The driver currently handles the 8168Bf and the 8168Be identically + * but they can be identified more specifically through the test below + * if needed: + * + * (RTL_R32(TxConfig) & 0x700000) == 0x500000 ? 8168Bf : 8168Be + * + * Same thing for the 8101Eb and the 8101Ec: + * + * (RTL_R32(TxConfig) & 0x700000) == 0x200000 ? 8101Eb : 8101Ec + */ const struct { u32 mask; int mac_version; @@ -1163,6 +1103,7 @@ static void rtl8169_get_mac_version(struct rtl8169_private *tp, void __iomem *io { 0x34000000, RTL_GIGA_MAC_VER_13 }, { 0x30800000, RTL_GIGA_MAC_VER_14 }, { 0x30000000, RTL_GIGA_MAC_VER_11 }, + { 0x98000000, RTL_GIGA_MAC_VER_06 }, { 0x18000000, RTL_GIGA_MAC_VER_05 }, { 0x10000000, RTL_GIGA_MAC_VER_04 }, { 0x04000000, RTL_GIGA_MAC_VER_03 }, @@ -1171,7 +1112,7 @@ static void rtl8169_get_mac_version(struct rtl8169_private *tp, void __iomem *io }, *p = mac_info; u32 reg; - reg = RTL_R32(TxConfig) & 0x7c800000; + reg = RTL_R32(TxConfig) & 0xfc800000; while ((reg & p->mask) != p->mask) p++; tp->mac_version = p->mac_version; @@ -1182,7 +1123,8 @@ static void rtl8169_print_mac_version(struct rtl8169_private *tp) dprintk("mac_version = 0x%02x\n", tp->mac_version); } -static void rtl8169_get_phy_version(struct rtl8169_private *tp, void __iomem *ioaddr) +static void rtl8169_get_phy_version(struct rtl8169_private *tp, + void __iomem *ioaddr) { const struct { u16 mask; @@ -1259,7 +1201,7 @@ static void rtl8169_hw_phy_config(struct net_device *dev) 0xbf00 } //w 0 15 0 bf00 } }, *p = phy_magic; - int i; + unsigned int i; rtl8169_print_mac_version(tp); rtl8169_print_phy_version(tp); @@ -1393,7 +1335,7 @@ static void rtl8169_phy_reset(struct net_device *dev, struct rtl8169_private *tp) { void __iomem *ioaddr = tp->mmio_addr; - int i; + unsigned int i; tp->phy_reset_enable(ioaddr); for (i = 0; i < 100; i++) { @@ -1408,21 +1350,16 @@ static void rtl8169_phy_reset(struct net_device *dev, static void rtl8169_init_phy(struct net_device *dev, struct rtl8169_private *tp) { void __iomem *ioaddr = tp->mmio_addr; - static int board_idx = -1; - u8 autoneg, duplex; - u16 speed; - - board_idx++; rtl8169_hw_phy_config(dev); dprintk("Set MAC Reg C+CR Offset 0x82h = 0x01h\n"); RTL_W8(0x82, 0x01); - if (tp->mac_version < RTL_GIGA_MAC_VER_03) { - dprintk("Set PCI Latency=0x40\n"); - pci_write_config_byte(tp->pci_dev, PCI_LATENCY_TIMER, 0x40); - } + pci_write_config_byte(tp->pci_dev, PCI_LATENCY_TIMER, 0x40); + + if (tp->mac_version <= RTL_GIGA_MAC_VER_06) + pci_write_config_byte(tp->pci_dev, PCI_CACHE_LINE_SIZE, 0x08); if (tp->mac_version == RTL_GIGA_MAC_VER_02) { dprintk("Set MAC Reg C+CR Offset 0x82h = 0x01h\n"); @@ -1431,16 +1368,52 @@ static void rtl8169_init_phy(struct net_device *dev, struct rtl8169_private *tp) mdio_write(ioaddr, 0x0b, 0x0000); //w 0x0b 15 0 0 } - rtl8169_link_option(board_idx, &autoneg, &speed, &duplex); - rtl8169_phy_reset(dev, tp); - rtl8169_set_speed(dev, autoneg, speed, duplex); + /* + * rtl8169_set_speed_xmii takes good care of the Fast Ethernet + * only 8101. Don't panic. + */ + rtl8169_set_speed(dev, AUTONEG_ENABLE, SPEED_1000, DUPLEX_FULL); if ((RTL_R8(PHYstatus) & TBI_Enable) && netif_msg_link(tp)) printk(KERN_INFO PFX "%s: TBI auto-negotiating\n", dev->name); } +static void rtl_rar_set(struct rtl8169_private *tp, u8 *addr) +{ + void __iomem *ioaddr = tp->mmio_addr; + u32 high; + u32 low; + + low = addr[0] | (addr[1] << 8) | (addr[2] << 16) | (addr[3] << 24); + high = addr[4] | (addr[5] << 8); + + spin_lock_irq(&tp->lock); + + RTL_W8(Cfg9346, Cfg9346_Unlock); + RTL_W32(MAC0, low); + RTL_W32(MAC4, high); + RTL_W8(Cfg9346, Cfg9346_Lock); + + spin_unlock_irq(&tp->lock); +} + +static int rtl_set_mac_address(struct net_device *dev, void *p) +{ + struct rtl8169_private *tp = netdev_priv(dev); + struct sockaddr *addr = p; + + if (!is_valid_ether_addr(addr->sa_data)) + return -EADDRNOTAVAIL; + + memcpy(dev->dev_addr, addr->sa_data, dev->addr_len); + + rtl_rar_set(tp, dev->dev_addr); + + return 0; +} + static int rtl8169_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) { struct rtl8169_private *tp = netdev_priv(dev); @@ -1467,15 +1440,49 @@ static int rtl8169_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd) return -EOPNOTSUPP; } +static const struct rtl_cfg_info { + void (*hw_start)(struct net_device *); + unsigned int region; + unsigned int align; + u16 intr_event; + u16 napi_event; +} rtl_cfg_infos [] = { + [RTL_CFG_0] = { + .hw_start = rtl_hw_start_8169, + .region = 1, + .align = 0, + .intr_event = SYSErr | LinkChg | RxOverflow | + RxFIFOOver | TxErr | TxOK | RxOK | RxErr, + .napi_event = RxFIFOOver | TxErr | TxOK | RxOK | RxOverflow + }, + [RTL_CFG_1] = { + .hw_start = rtl_hw_start_8168, + .region = 2, + .align = 8, + .intr_event = SYSErr | LinkChg | RxOverflow | + TxErr | TxOK | RxOK | RxErr, + .napi_event = TxErr | TxOK | RxOK | RxOverflow + }, + [RTL_CFG_2] = { + .hw_start = rtl_hw_start_8101, + .region = 2, + .align = 8, + .intr_event = SYSErr | LinkChg | RxOverflow | PCSTimeout | + RxFIFOOver | TxErr | TxOK | RxOK | RxErr, + .napi_event = RxFIFOOver | TxErr | TxOK | RxOK | RxOverflow + } +}; + static int __devinit rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { - const unsigned int region = rtl_cfg_info[ent->driver_data].region; + const struct rtl_cfg_info *cfg = rtl_cfg_infos + ent->driver_data; + const unsigned int region = cfg->region; struct rtl8169_private *tp; struct net_device *dev; void __iomem *ioaddr; - unsigned int pm_cap; - int i, rc; + unsigned int i; + int rc; if (netif_msg_drv(&debug)) { printk(KERN_INFO "%s Gigabit Ethernet driver %s loaded\n", @@ -1508,20 +1515,6 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) if (rc < 0) goto err_out_disable_2; - /* save power state before pci_enable_device overwrites it */ - pm_cap = pci_find_capability(pdev, PCI_CAP_ID_PM); - if (pm_cap) { - u16 pwr_command, acpi_idle_state; - - pci_read_config_word(pdev, pm_cap + PCI_PM_CTRL, &pwr_command); - acpi_idle_state = pwr_command & PCI_PM_CTRL_STATE_MASK; - } else { - if (netif_msg_probe(tp)) { - dev_err(&pdev->dev, - "PowerManagement capability not found.\n"); - } - } - /* make sure PCI base addr 1 is MMIO */ if (!(pci_resource_flags(pdev, region) & IORESOURCE_MEM)) { if (netif_msg_probe(tp)) { @@ -1585,7 +1578,7 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) RTL_W8(ChipCmd, CmdReset); /* Check that the chip has finished the reset. */ - for (i = 100; i > 0; i--) { + for (i = 0; i < 100; i++) { if ((RTL_R8(ChipCmd) & CmdReset) == 0) break; msleep_interruptible(1); @@ -1647,11 +1640,12 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) SET_ETHTOOL_OPS(dev, &rtl8169_ethtool_ops); dev->stop = rtl8169_close; dev->tx_timeout = rtl8169_tx_timeout; - dev->set_multicast_list = rtl8169_set_rx_mode; + dev->set_multicast_list = rtl_set_rx_mode; dev->watchdog_timeo = RTL8169_TX_TIMEOUT; dev->irq = pdev->irq; dev->base_addr = (unsigned long) ioaddr; dev->change_mtu = rtl8169_change_mtu; + dev->set_mac_address = rtl_set_mac_address; #ifdef CONFIG_R8169_NAPI dev->poll = rtl8169_poll; @@ -1670,7 +1664,10 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) tp->intr_mask = 0xffff; tp->pci_dev = pdev; tp->mmio_addr = ioaddr; - tp->align = rtl_cfg_info[ent->driver_data].align; + tp->align = cfg->align; + tp->hw_start = cfg->hw_start; + tp->intr_event = cfg->intr_event; + tp->napi_event = cfg->napi_event; init_timer(&tp->timer); tp->timer.data = (unsigned long) dev; @@ -1685,15 +1682,17 @@ rtl8169_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) pci_set_drvdata(pdev, dev); if (netif_msg_probe(tp)) { + u32 xid = RTL_R32(TxConfig) & 0x7cf0f8ff; + printk(KERN_INFO "%s: %s at 0x%lx, " "%2.2x:%2.2x:%2.2x:%2.2x:%2.2x:%2.2x, " - "IRQ %d\n", + "XID %08x IRQ %d\n", dev->name, rtl_chip_info[tp->chipset].name, dev->base_addr, dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2], dev->dev_addr[3], - dev->dev_addr[4], dev->dev_addr[5], dev->irq); + dev->dev_addr[4], dev->dev_addr[5], xid, dev->irq); } rtl8169_init_phy(dev, tp); @@ -1714,15 +1713,11 @@ err_out_free_dev_1: goto out; } -static void __devexit -rtl8169_remove_one(struct pci_dev *pdev) +static void __devexit rtl8169_remove_one(struct pci_dev *pdev) { struct net_device *dev = pci_get_drvdata(pdev); struct rtl8169_private *tp = netdev_priv(dev); - assert(dev != NULL); - assert(tp != NULL); - flush_scheduled_work(); unregister_netdev(dev); @@ -1774,7 +1769,7 @@ static int rtl8169_open(struct net_device *dev) if (retval < 0) goto err_release_ring_2; - rtl8169_hw_start(dev); + rtl_hw_start(dev); rtl8169_request_timer(dev); @@ -1805,7 +1800,7 @@ static void rtl8169_hw_reset(void __iomem *ioaddr) RTL_R8(ChipCmd); } -static void rtl8169_set_rx_tx_config_registers(struct rtl8169_private *tp) +static void rtl_set_rx_tx_config_registers(struct rtl8169_private *tp) { void __iomem *ioaddr = tp->mmio_addr; u32 cfg = rtl8169_rx_config; @@ -1818,45 +1813,90 @@ static void rtl8169_set_rx_tx_config_registers(struct rtl8169_private *tp) (InterFrameGap << TxInterFrameGapShift)); } -static void rtl8169_hw_start(struct net_device *dev) +static void rtl_hw_start(struct net_device *dev) { struct rtl8169_private *tp = netdev_priv(dev); void __iomem *ioaddr = tp->mmio_addr; - struct pci_dev *pdev = tp->pci_dev; - u16 cmd; - u32 i; + unsigned int i; /* Soft reset the chip. */ RTL_W8(ChipCmd, CmdReset); /* Check that the chip has finished the reset. */ - for (i = 100; i > 0; i--) { + for (i = 0; i < 100; i++) { if ((RTL_R8(ChipCmd) & CmdReset) == 0) break; msleep_interruptible(1); } - if (tp->mac_version == RTL_GIGA_MAC_VER_05) { - RTL_W16(CPlusCmd, RTL_R16(CPlusCmd) | PCIMulRW); - pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x08); - } + tp->hw_start(dev); - if (tp->mac_version == RTL_GIGA_MAC_VER_13) { - pci_write_config_word(pdev, 0x68, 0x00); - pci_write_config_word(pdev, 0x69, 0x08); - } + netif_start_queue(dev); +} - /* Undocumented stuff. */ - if (tp->mac_version == RTL_GIGA_MAC_VER_05) { - /* Realtek's r1000_n.c driver uses '&& 0x01' here. Well... */ - if ((RTL_R8(Config2) & 0x07) & 0x01) - RTL_W32(0x7c, 0x0007ffff); - RTL_W32(0x7c, 0x0007ff00); +static void rtl_set_rx_tx_desc_registers(struct rtl8169_private *tp, + void __iomem *ioaddr) +{ + /* + * Magic spell: some iop3xx ARM board needs the TxDescAddrHigh + * register to be written before TxDescAddrLow to work. + * Switching from MMIO to I/O access fixes the issue as well. + */ + RTL_W32(TxDescStartAddrHigh, ((u64) tp->TxPhyAddr) >> 32); + RTL_W32(TxDescStartAddrLow, ((u64) tp->TxPhyAddr) & DMA_32BIT_MASK); + RTL_W32(RxDescAddrHigh, ((u64) tp->RxPhyAddr) >> 32); + RTL_W32(RxDescAddrLow, ((u64) tp->RxPhyAddr) & DMA_32BIT_MASK); +} + +static u16 rtl_rw_cpluscmd(void __iomem *ioaddr) +{ + u16 cmd; + + cmd = RTL_R16(CPlusCmd); + RTL_W16(CPlusCmd, cmd); + return cmd; +} + +static void rtl_set_rx_max_size(void __iomem *ioaddr) +{ + /* Low hurts. Let's disable the filtering. */ + RTL_W16(RxMaxSize, 16383); +} + +static void rtl8169_set_magic_reg(void __iomem *ioaddr, unsigned mac_version) +{ + struct { + u32 mac_version; + u32 clk; + u32 val; + } cfg2_info [] = { + { RTL_GIGA_MAC_VER_05, PCI_Clock_33MHz, 0x000fff00 }, // 8110SCd + { RTL_GIGA_MAC_VER_05, PCI_Clock_66MHz, 0x000fffff }, + { RTL_GIGA_MAC_VER_06, PCI_Clock_33MHz, 0x00ffff00 }, // 8110SCe + { RTL_GIGA_MAC_VER_06, PCI_Clock_66MHz, 0x00ffffff } + }, *p = cfg2_info; + unsigned int i; + u32 clk; - pci_read_config_word(pdev, PCI_COMMAND, &cmd); - cmd = cmd & 0xef; - pci_write_config_word(pdev, PCI_COMMAND, cmd); + clk = RTL_R8(Config2) & PCI_Clock_66MHz; + for (i = 0; i < ARRAY_SIZE(cfg2_info); i++) { + if ((p->mac_version == mac_version) && (p->clk == clk)) { + RTL_W32(0x7c, p->val); + break; + } + } +} + +static void rtl_hw_start_8169(struct net_device *dev) +{ + struct rtl8169_private *tp = netdev_priv(dev); + void __iomem *ioaddr = tp->mmio_addr; + struct pci_dev *pdev = tp->pci_dev; + + if (tp->mac_version == RTL_GIGA_MAC_VER_05) { + RTL_W16(CPlusCmd, RTL_R16(CPlusCmd) | PCIMulRW); + pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, 0x08); } RTL_W8(Cfg9346, Cfg9346_Unlock); @@ -1868,19 +1908,11 @@ static void rtl8169_hw_start(struct net_device *dev) RTL_W8(EarlyTxThres, EarlyTxThld); - /* Low hurts. Let's disable the filtering. */ - RTL_W16(RxMaxSize, 16383); - - if ((tp->mac_version == RTL_GIGA_MAC_VER_01) || - (tp->mac_version == RTL_GIGA_MAC_VER_02) || - (tp->mac_version == RTL_GIGA_MAC_VER_03) || - (tp->mac_version == RTL_GIGA_MAC_VER_04)) - rtl8169_set_rx_tx_config_registers(tp); + rtl_set_rx_max_size(ioaddr); - cmd = RTL_R16(CPlusCmd); - RTL_W16(CPlusCmd, cmd); + rtl_set_rx_tx_config_registers(tp); - tp->cp_cmd |= cmd | PCIMulRW; + tp->cp_cmd |= rtl_rw_cpluscmd(ioaddr) | PCIMulRW; if ((tp->mac_version == RTL_GIGA_MAC_VER_02) || (tp->mac_version == RTL_GIGA_MAC_VER_03)) { @@ -1891,29 +1923,15 @@ static void rtl8169_hw_start(struct net_device *dev) RTL_W16(CPlusCmd, tp->cp_cmd); + rtl8169_set_magic_reg(ioaddr, tp->mac_version); + /* * Undocumented corner. Supposedly: * (TxTimer << 12) | (TxPackets << 8) | (RxTimer << 4) | RxPackets */ RTL_W16(IntrMitigate, 0x0000); - /* - * Magic spell: some iop3xx ARM board needs the TxDescAddrHigh - * register to be written before TxDescAddrLow to work. - * Switching from MMIO to I/O access fixes the issue as well. - */ - RTL_W32(TxDescStartAddrHigh, ((u64) tp->TxPhyAddr >> 32)); - RTL_W32(TxDescStartAddrLow, ((u64) tp->TxPhyAddr & DMA_32BIT_MASK)); - RTL_W32(RxDescAddrHigh, ((u64) tp->RxPhyAddr >> 32)); - RTL_W32(RxDescAddrLow, ((u64) tp->RxPhyAddr & DMA_32BIT_MASK)); - - if ((tp->mac_version != RTL_GIGA_MAC_VER_01) && - (tp->mac_version != RTL_GIGA_MAC_VER_02) && - (tp->mac_version != RTL_GIGA_MAC_VER_03) && - (tp->mac_version != RTL_GIGA_MAC_VER_04)) { - RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb); - rtl8169_set_rx_tx_config_registers(tp); - } + rtl_set_rx_tx_desc_registers(tp, ioaddr); RTL_W8(Cfg9346, Cfg9346_Lock); @@ -1922,15 +1940,107 @@ static void rtl8169_hw_start(struct net_device *dev) RTL_W32(RxMissed, 0); - rtl8169_set_rx_mode(dev); + rtl_set_rx_mode(dev); /* no early-rx interrupts */ RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xF000); /* Enable all known interrupts by setting the interrupt mask. */ - RTL_W16(IntrMask, rtl8169_intr_mask); + RTL_W16(IntrMask, tp->intr_event); - netif_start_queue(dev); + RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb); +} + +static void rtl_hw_start_8168(struct net_device *dev) +{ + struct rtl8169_private *tp = netdev_priv(dev); + void __iomem *ioaddr = tp->mmio_addr; + struct pci_dev *pdev = tp->pci_dev; + u8 ctl; + + RTL_W8(Cfg9346, Cfg9346_Unlock); + + RTL_W8(EarlyTxThres, EarlyTxThld); + + rtl_set_rx_max_size(ioaddr); + + rtl_set_rx_tx_config_registers(tp); + + tp->cp_cmd |= RTL_R16(CPlusCmd) | PktCntrDisable | INTT_1; + + RTL_W16(CPlusCmd, tp->cp_cmd); + + /* Tx performance tweak. */ + pci_read_config_byte(pdev, 0x69, &ctl); + ctl = (ctl & ~0x70) | 0x50; + pci_write_config_byte(pdev, 0x69, ctl); + + RTL_W16(IntrMitigate, 0x5151); + + /* Work around for RxFIFO overflow. */ + if (tp->mac_version == RTL_GIGA_MAC_VER_11) { + tp->intr_event |= RxFIFOOver | PCSTimeout; + tp->intr_event &= ~RxOverflow; + } + + rtl_set_rx_tx_desc_registers(tp, ioaddr); + + RTL_W8(Cfg9346, Cfg9346_Lock); + + RTL_R8(IntrMask); + + RTL_W32(RxMissed, 0); + + rtl_set_rx_mode(dev); + + RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb); + + RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xF000); + + RTL_W16(IntrMask, tp->intr_event); +} + +static void rtl_hw_start_8101(struct net_device *dev) +{ + struct rtl8169_private *tp = netdev_priv(dev); + void __iomem *ioaddr = tp->mmio_addr; + struct pci_dev *pdev = tp->pci_dev; + + if (tp->mac_version == RTL_GIGA_MAC_VER_13) { + pci_write_config_word(pdev, 0x68, 0x00); + pci_write_config_word(pdev, 0x69, 0x08); + } + + RTL_W8(Cfg9346, Cfg9346_Unlock); + + RTL_W8(EarlyTxThres, EarlyTxThld); + + rtl_set_rx_max_size(ioaddr); + + tp->cp_cmd |= rtl_rw_cpluscmd(ioaddr) | PCIMulRW; + + RTL_W16(CPlusCmd, tp->cp_cmd); + + RTL_W16(IntrMitigate, 0x0000); + + rtl_set_rx_tx_desc_registers(tp, ioaddr); + + RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb); + rtl_set_rx_tx_config_registers(tp); + + RTL_W8(Cfg9346, Cfg9346_Lock); + + RTL_R8(IntrMask); + + RTL_W32(RxMissed, 0); + + rtl_set_rx_mode(dev); + + RTL_W8(ChipCmd, CmdTxEnb | CmdRxEnb); + + RTL_W16(MultiIntr, RTL_R16(MultiIntr) & 0xf000); + + RTL_W16(IntrMask, tp->intr_event); } static int rtl8169_change_mtu(struct net_device *dev, int new_mtu) @@ -1956,7 +2066,7 @@ static int rtl8169_change_mtu(struct net_device *dev, int new_mtu) netif_poll_enable(dev); - rtl8169_hw_start(dev); + rtl_hw_start(dev); rtl8169_request_timer(dev); @@ -1997,38 +2107,38 @@ static inline void rtl8169_map_to_asic(struct RxDesc *desc, dma_addr_t mapping, rtl8169_mark_to_asic(desc, rx_buf_sz); } -static int rtl8169_alloc_rx_skb(struct pci_dev *pdev, struct sk_buff **sk_buff, - struct RxDesc *desc, int rx_buf_sz, - unsigned int align) +static struct sk_buff *rtl8169_alloc_rx_skb(struct pci_dev *pdev, + struct net_device *dev, + struct RxDesc *desc, int rx_buf_sz, + unsigned int align) { struct sk_buff *skb; dma_addr_t mapping; - int ret = 0; + unsigned int pad; - skb = dev_alloc_skb(rx_buf_sz + align); + pad = align ? align : NET_IP_ALIGN; + + skb = netdev_alloc_skb(dev, rx_buf_sz + pad); if (!skb) goto err_out; - skb_reserve(skb, (align - 1) & (unsigned long)skb->data); - *sk_buff = skb; + skb_reserve(skb, align ? ((pad - 1) & (unsigned long)skb->data) : pad); mapping = pci_map_single(pdev, skb->data, rx_buf_sz, PCI_DMA_FROMDEVICE); rtl8169_map_to_asic(desc, mapping, rx_buf_sz); - out: - return ret; + return skb; err_out: - ret = -ENOMEM; rtl8169_make_unusable_by_asic(desc); goto out; } static void rtl8169_rx_clear(struct rtl8169_private *tp) { - int i; + unsigned int i; for (i = 0; i < NUM_RX_DESC; i++) { if (tp->Rx_skbuff[i]) { @@ -2043,16 +2153,22 @@ static u32 rtl8169_rx_fill(struct rtl8169_private *tp, struct net_device *dev, { u32 cur; - for (cur = start; end - cur > 0; cur++) { - int ret, i = cur % NUM_RX_DESC; + for (cur = start; end - cur != 0; cur++) { + struct sk_buff *skb; + unsigned int i = cur % NUM_RX_DESC; + + WARN_ON((s32)(end - cur) < 0); if (tp->Rx_skbuff[i]) continue; - ret = rtl8169_alloc_rx_skb(tp->pci_dev, tp->Rx_skbuff + i, - tp->RxDescArray + i, tp->rx_buf_sz, tp->align); - if (ret < 0) + skb = rtl8169_alloc_rx_skb(tp->pci_dev, dev, + tp->RxDescArray + i, + tp->rx_buf_sz, tp->align); + if (!skb) break; + + tp->Rx_skbuff[i] = skb; } return cur - start; } @@ -2164,14 +2280,9 @@ static void rtl8169_reinit_task(struct work_struct *work) ret = rtl8169_open(dev); if (unlikely(ret < 0)) { - if (net_ratelimit()) { - struct rtl8169_private *tp = netdev_priv(dev); - - if (netif_msg_drv(tp)) { - printk(PFX KERN_ERR - "%s: reinit failure (status = %d)." - " Rescheduling.\n", dev->name, ret); - } + if (net_ratelimit() && netif_msg_drv(tp)) { + printk(PFX KERN_ERR "%s: reinit failure (status = %d)." + " Rescheduling.\n", dev->name, ret); } rtl8169_schedule_work(dev, rtl8169_reinit_task); } @@ -2198,16 +2309,12 @@ static void rtl8169_reset_task(struct work_struct *work) if (tp->dirty_rx == tp->cur_rx) { rtl8169_init_ring_indexes(tp); - rtl8169_hw_start(dev); + rtl_hw_start(dev); netif_wake_queue(dev); } else { - if (net_ratelimit()) { - struct rtl8169_private *tp = netdev_priv(dev); - - if (netif_msg_intr(tp)) { - printk(PFX KERN_EMERG - "%s: Rx buffers shortage\n", dev->name); - } + if (net_ratelimit() && netif_msg_intr(tp)) { + printk(PFX KERN_EMERG "%s: Rx buffers shortage\n", + dev->name); } rtl8169_schedule_work(dev, rtl8169_reset_task); } @@ -2344,7 +2451,7 @@ static int rtl8169_start_xmit(struct sk_buff *skb, struct net_device *dev) smp_wmb(); - RTL_W8(TxPoll, 0x40); /* set polling bit */ + RTL_W8(TxPoll, NPQ); /* set polling bit */ if (TX_BUFFS_AVAIL(tp) < MAX_SKB_FRAGS) { netif_stop_queue(dev); @@ -2414,16 +2521,12 @@ static void rtl8169_pcierr_interrupt(struct net_device *dev) rtl8169_schedule_work(dev, rtl8169_reinit_task); } -static void -rtl8169_tx_interrupt(struct net_device *dev, struct rtl8169_private *tp, - void __iomem *ioaddr) +static void rtl8169_tx_interrupt(struct net_device *dev, + struct rtl8169_private *tp, + void __iomem *ioaddr) { unsigned int dirty_tx, tx_left; - assert(dev != NULL); - assert(tp != NULL); - assert(ioaddr != NULL); - dirty_tx = tp->dirty_tx; smp_rmb(); tx_left = tp->cur_tx - dirty_tx; @@ -2480,38 +2583,37 @@ static inline void rtl8169_rx_csum(struct sk_buff *skb, struct RxDesc *desc) skb->ip_summed = CHECKSUM_NONE; } -static inline int rtl8169_try_rx_copy(struct sk_buff **sk_buff, int pkt_size, - struct RxDesc *desc, int rx_buf_sz, - unsigned int align) +static inline bool rtl8169_try_rx_copy(struct sk_buff **sk_buff, + struct rtl8169_private *tp, int pkt_size, + dma_addr_t addr) { - int ret = -1; + struct sk_buff *skb; + bool done = false; - if (pkt_size < rx_copybreak) { - struct sk_buff *skb; + if (pkt_size >= rx_copybreak) + goto out; - skb = dev_alloc_skb(pkt_size + align); - if (skb) { - skb_reserve(skb, (align - 1) & (unsigned long)skb->data); - eth_copy_and_sum(skb, sk_buff[0]->data, pkt_size, 0); - *sk_buff = skb; - rtl8169_mark_to_asic(desc, rx_buf_sz); - ret = 0; - } - } - return ret; + skb = netdev_alloc_skb(tp->dev, pkt_size + NET_IP_ALIGN); + if (!skb) + goto out; + + pci_dma_sync_single_for_cpu(tp->pci_dev, addr, pkt_size, + PCI_DMA_FROMDEVICE); + skb_reserve(skb, NET_IP_ALIGN); + skb_copy_from_linear_data(*sk_buff, skb->data, pkt_size); + *sk_buff = skb; + done = true; +out: + return done; } -static int -rtl8169_rx_interrupt(struct net_device *dev, struct rtl8169_private *tp, - void __iomem *ioaddr) +static int rtl8169_rx_interrupt(struct net_device *dev, + struct rtl8169_private *tp, + void __iomem *ioaddr) { unsigned int cur_rx, rx_left; unsigned int delta, count; - assert(dev != NULL); - assert(tp != NULL); - assert(ioaddr != NULL); - cur_rx = tp->cur_rx; rx_left = NUM_RX_DESC + tp->dirty_rx - cur_rx; rx_left = rtl8169_rx_quota(rx_left, (u32) dev->quota); @@ -2544,9 +2646,9 @@ rtl8169_rx_interrupt(struct net_device *dev, struct rtl8169_private *tp, rtl8169_mark_to_asic(desc, tp->rx_buf_sz); } else { struct sk_buff *skb = tp->Rx_skbuff[entry]; + dma_addr_t addr = le64_to_cpu(desc->addr); int pkt_size = (status & 0x00001FFF) - 4; - void (*pci_action)(struct pci_dev *, dma_addr_t, - size_t, int) = pci_dma_sync_single_for_device; + struct pci_dev *pdev = tp->pci_dev; /* * The driver does not support incoming fragmented @@ -2562,19 +2664,16 @@ rtl8169_rx_interrupt(struct net_device *dev, struct rtl8169_private *tp, rtl8169_rx_csum(skb, desc); - pci_dma_sync_single_for_cpu(tp->pci_dev, - le64_to_cpu(desc->addr), tp->rx_buf_sz, - PCI_DMA_FROMDEVICE); - - if (rtl8169_try_rx_copy(&skb, pkt_size, desc, - tp->rx_buf_sz, tp->align)) { - pci_action = pci_unmap_single; + if (rtl8169_try_rx_copy(&skb, tp, pkt_size, addr)) { + pci_dma_sync_single_for_device(pdev, addr, + pkt_size, PCI_DMA_FROMDEVICE); + rtl8169_mark_to_asic(desc, tp->rx_buf_sz); + } else { + pci_unmap_single(pdev, addr, pkt_size, + PCI_DMA_FROMDEVICE); tp->Rx_skbuff[entry] = NULL; } - pci_action(tp->pci_dev, le64_to_cpu(desc->addr), - tp->rx_buf_sz, PCI_DMA_FROMDEVICE); - skb_put(skb, pkt_size); skb->protocol = eth_type_trans(skb, dev); @@ -2585,6 +2684,13 @@ rtl8169_rx_interrupt(struct net_device *dev, struct rtl8169_private *tp, tp->stats.rx_bytes += pkt_size; tp->stats.rx_packets++; } + + /* Work around for AMD plateform. */ + if ((desc->opts2 & 0xfffe000) && + (tp->mac_version == RTL_GIGA_MAC_VER_05)) { + desc->opts2 = 0; + cur_rx++; + } } count = cur_rx - tp->cur_rx; @@ -2608,11 +2714,9 @@ rtl8169_rx_interrupt(struct net_device *dev, struct rtl8169_private *tp, return count; } -/* The interrupt handler does all of the Rx thread work and cleans up after the Tx thread. */ -static irqreturn_t -rtl8169_interrupt(int irq, void *dev_instance) +static irqreturn_t rtl8169_interrupt(int irq, void *dev_instance) { - struct net_device *dev = (struct net_device *) dev_instance; + struct net_device *dev = dev_instance; struct rtl8169_private *tp = netdev_priv(dev); int boguscnt = max_interrupt_work; void __iomem *ioaddr = tp->mmio_addr; @@ -2637,9 +2741,17 @@ rtl8169_interrupt(int irq, void *dev_instance) RTL_W16(IntrStatus, (status & RxFIFOOver) ? (status | RxOverflow) : status); - if (!(status & rtl8169_intr_mask)) + if (!(status & tp->intr_event)) break; + /* Work around for rx fifo overflow */ + if (unlikely(status & RxFIFOOver) && + (tp->mac_version == RTL_GIGA_MAC_VER_11)) { + netif_stop_queue(dev); + rtl8169_tx_timeout(dev); + break; + } + if (unlikely(status & SYSErr)) { rtl8169_pcierr_interrupt(dev); break; @@ -2649,8 +2761,8 @@ rtl8169_interrupt(int irq, void *dev_instance) rtl8169_check_link_status(dev, tp, ioaddr); #ifdef CONFIG_R8169_NAPI - RTL_W16(IntrMask, rtl8169_intr_mask & ~rtl8169_napi_event); - tp->intr_mask = ~rtl8169_napi_event; + RTL_W16(IntrMask, tp->intr_event & ~tp->napi_event); + tp->intr_mask = ~tp->napi_event; if (likely(netif_rx_schedule_prep(dev))) __netif_rx_schedule(dev); @@ -2661,9 +2773,9 @@ rtl8169_interrupt(int irq, void *dev_instance) break; #else /* Rx interrupt */ - if (status & (RxOK | RxOverflow | RxFIFOOver)) { + if (status & (RxOK | RxOverflow | RxFIFOOver)) rtl8169_rx_interrupt(dev, tp, ioaddr); - } + /* Tx interrupt */ if (status & (TxOK | TxErr)) rtl8169_tx_interrupt(dev, tp, ioaddr); @@ -2707,7 +2819,7 @@ static int rtl8169_poll(struct net_device *dev, int *budget) * write is safe - FR */ smp_wmb(); - RTL_W16(IntrMask, rtl8169_intr_mask); + RTL_W16(IntrMask, tp->intr_event); } return (work_done >= work_to_do); @@ -2789,14 +2901,13 @@ static int rtl8169_close(struct net_device *dev) return 0; } -static void -rtl8169_set_rx_mode(struct net_device *dev) +static void rtl_set_rx_mode(struct net_device *dev) { struct rtl8169_private *tp = netdev_priv(dev); void __iomem *ioaddr = tp->mmio_addr; unsigned long flags; u32 mc_filter[2]; /* Multicast hash filter */ - int i, rx_mode; + int rx_mode; u32 tmp = 0; if (dev->flags & IFF_PROMISC) { @@ -2816,6 +2927,8 @@ rtl8169_set_rx_mode(struct net_device *dev) mc_filter[1] = mc_filter[0] = 0xffffffff; } else { struct dev_mc_list *mclist; + unsigned int i; + rx_mode = AcceptBroadcast | AcceptMyPhys; mc_filter[1] = mc_filter[0] = 0; for (i = 0, mclist = dev->mc_list; mclist && i < dev->mc_count; @@ -2840,10 +2953,11 @@ rtl8169_set_rx_mode(struct net_device *dev) mc_filter[1] = 0xffffffff; } - RTL_W32(RxConfig, tmp); RTL_W32(MAR0 + 0, mc_filter[0]); RTL_W32(MAR0 + 4, mc_filter[1]); + RTL_W32(RxConfig, tmp); + spin_unlock_irqrestore(&tp->lock, flags); } @@ -2931,14 +3045,12 @@ static struct pci_driver rtl8169_pci_driver = { #endif }; -static int __init -rtl8169_init_module(void) +static int __init rtl8169_init_module(void) { return pci_register_driver(&rtl8169_pci_driver); } -static void __exit -rtl8169_cleanup_module(void) +static void __exit rtl8169_cleanup_module(void) { pci_unregister_driver(&rtl8169_pci_driver); } diff --git a/drivers/net/s2io.c b/drivers/net/s2io.c index 09078ff84cd..2d826fff7e2 100644 --- a/drivers/net/s2io.c +++ b/drivers/net/s2io.c @@ -469,11 +469,18 @@ static struct pci_device_id s2io_tbl[] __devinitdata = { MODULE_DEVICE_TABLE(pci, s2io_tbl); +static struct pci_error_handlers s2io_err_handler = { + .error_detected = s2io_io_error_detected, + .slot_reset = s2io_io_slot_reset, + .resume = s2io_io_resume, +}; + static struct pci_driver s2io_driver = { .name = "S2IO", .id_table = s2io_tbl, .probe = s2io_init_nic, .remove = __devexit_p(s2io_rem_nic), + .err_handler = &s2io_err_handler, }; /* A simplifier macro used both by init and free shared_mem Fns(). */ @@ -2689,6 +2696,9 @@ static void s2io_netpoll(struct net_device *dev) u64 val64 = 0xFFFFFFFFFFFFFFFFULL; int i; + if (pci_channel_offline(nic->pdev)) + return; + disable_irq(dev->irq); atomic_inc(&nic->isr_cnt); @@ -3215,6 +3225,8 @@ static void alarm_intr_handler(struct s2io_nic *nic) int i; if (atomic_read(&nic->card_state) == CARD_DOWN) return; + if (pci_channel_offline(nic->pdev)) + return; nic->mac_control.stats_info->sw_stat.ring_full_cnt = 0; /* Handling the XPAK counters update */ if(nic->mac_control.stats_info->xpak_stat.xpak_timer_count < 72000) { @@ -3958,7 +3970,6 @@ static int s2io_close(struct net_device *dev) /* Reset card, kill tasklet and free Tx and Rx buffers. */ s2io_card_down(sp); - sp->device_close_flag = TRUE; /* Device is shut down. */ return 0; } @@ -4314,6 +4325,10 @@ static irqreturn_t s2io_isr(int irq, void *dev_id) struct mac_info *mac_control; struct config_param *config; + /* Pretend we handled any irq's from a disconnected card */ + if (pci_channel_offline(sp->pdev)) + return IRQ_NONE; + atomic_inc(&sp->isr_cnt); mac_control = &sp->mac_control; config = &sp->config; @@ -6569,7 +6584,7 @@ static void s2io_rem_isr(struct s2io_nic * sp) } while(cnt < 5); } -static void s2io_card_down(struct s2io_nic * sp) +static void do_s2io_card_down(struct s2io_nic * sp, int do_io) { int cnt = 0; struct XENA_dev_config __iomem *bar0 = sp->bar0; @@ -6584,7 +6599,8 @@ static void s2io_card_down(struct s2io_nic * sp) atomic_set(&sp->card_state, CARD_DOWN); /* disable Tx and Rx traffic on the NIC */ - stop_nic(sp); + if (do_io) + stop_nic(sp); s2io_rem_isr(sp); @@ -6592,7 +6608,7 @@ static void s2io_card_down(struct s2io_nic * sp) tasklet_kill(&sp->task); /* Check if the device is Quiescent and then Reset the NIC */ - do { + while(do_io) { /* As per the HW requirement we need to replenish the * receive buffer to avoid the ring bump. Since there is * no intention of processing the Rx frame at this pointwe are @@ -6617,8 +6633,9 @@ static void s2io_card_down(struct s2io_nic * sp) (unsigned long long) val64); break; } - } while (1); - s2io_reset(sp); + } + if (do_io) + s2io_reset(sp); spin_lock_irqsave(&sp->tx_lock, flags); /* Free all Tx buffers */ @@ -6633,6 +6650,11 @@ static void s2io_card_down(struct s2io_nic * sp) clear_bit(0, &(sp->link_state)); } +static void s2io_card_down(struct s2io_nic * sp) +{ + do_s2io_card_down(sp, 1); +} + static int s2io_card_up(struct s2io_nic * sp) { int i, ret = 0; @@ -8010,3 +8032,85 @@ static void lro_append_pkt(struct s2io_nic *sp, struct lro *lro, sp->mac_control.stats_info->sw_stat.clubbed_frms_cnt++; return; } + +/** + * s2io_io_error_detected - called when PCI error is detected + * @pdev: Pointer to PCI device + * @state: The current pci conneection state + * + * This function is called after a PCI bus error affecting + * this device has been detected. + */ +static pci_ers_result_t s2io_io_error_detected(struct pci_dev *pdev, + pci_channel_state_t state) +{ + struct net_device *netdev = pci_get_drvdata(pdev); + struct s2io_nic *sp = netdev->priv; + + netif_device_detach(netdev); + + if (netif_running(netdev)) { + /* Bring down the card, while avoiding PCI I/O */ + do_s2io_card_down(sp, 0); + } + pci_disable_device(pdev); + + return PCI_ERS_RESULT_NEED_RESET; +} + +/** + * s2io_io_slot_reset - called after the pci bus has been reset. + * @pdev: Pointer to PCI device + * + * Restart the card from scratch, as if from a cold-boot. + * At this point, the card has exprienced a hard reset, + * followed by fixups by BIOS, and has its config space + * set up identically to what it was at cold boot. + */ +static pci_ers_result_t s2io_io_slot_reset(struct pci_dev *pdev) +{ + struct net_device *netdev = pci_get_drvdata(pdev); + struct s2io_nic *sp = netdev->priv; + + if (pci_enable_device(pdev)) { + printk(KERN_ERR "s2io: " + "Cannot re-enable PCI device after reset.\n"); + return PCI_ERS_RESULT_DISCONNECT; + } + + pci_set_master(pdev); + s2io_reset(sp); + + return PCI_ERS_RESULT_RECOVERED; +} + +/** + * s2io_io_resume - called when traffic can start flowing again. + * @pdev: Pointer to PCI device + * + * This callback is called when the error recovery driver tells + * us that its OK to resume normal operation. + */ +static void s2io_io_resume(struct pci_dev *pdev) +{ + struct net_device *netdev = pci_get_drvdata(pdev); + struct s2io_nic *sp = netdev->priv; + + if (netif_running(netdev)) { + if (s2io_card_up(sp)) { + printk(KERN_ERR "s2io: " + "Can't bring device back up after reset.\n"); + return; + } + + if (s2io_set_mac_addr(netdev, netdev->dev_addr) == FAILURE) { + s2io_card_down(sp); + printk(KERN_ERR "s2io: " + "Can't resetore mac addr after reset.\n"); + return; + } + } + + netif_device_attach(netdev); + netif_wake_queue(netdev); +} diff --git a/drivers/net/s2io.h b/drivers/net/s2io.h index 54baa0b8ec7..58592780f51 100644 --- a/drivers/net/s2io.h +++ b/drivers/net/s2io.h @@ -794,7 +794,6 @@ struct s2io_nic { struct net_device_stats stats; int high_dma_flag; - int device_close_flag; int device_enabled_once; char name[60]; @@ -1052,6 +1051,11 @@ static void lro_append_pkt(struct s2io_nic *sp, struct lro *lro, struct sk_buff *skb, u32 tcp_len); static int rts_ds_steer(struct s2io_nic *nic, u8 ds_codepoint, u8 ring); +static pci_ers_result_t s2io_io_error_detected(struct pci_dev *pdev, + pci_channel_state_t state); +static pci_ers_result_t s2io_io_slot_reset(struct pci_dev *pdev); +static void s2io_io_resume(struct pci_dev *pdev); + #define s2io_tcp_mss(skb) skb_shinfo(skb)->gso_size #define s2io_udp_mss(skb) skb_shinfo(skb)->gso_size #define s2io_offload_type(skb) skb_shinfo(skb)->gso_type diff --git a/drivers/net/sky2.c b/drivers/net/sky2.c index fe01b961b59..b51d73c8f81 100644 --- a/drivers/net/sky2.c +++ b/drivers/net/sky2.c @@ -50,7 +50,7 @@ #include "sky2.h" #define DRV_NAME "sky2" -#define DRV_VERSION "1.14" +#define DRV_VERSION "1.15" #define PFX DRV_NAME " " /* @@ -130,7 +130,7 @@ static const struct pci_device_id sky2_id_table[] = { { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4368) }, /* 88EC034 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x4369) }, /* 88EC042 */ { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436A) }, /* 88E8058 */ -// { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436B) }, /* 88E8071 */ + { PCI_DEVICE(PCI_VENDOR_ID_MARVELL, 0x436B) }, /* 88E8071 */ { 0 } }; @@ -217,13 +217,24 @@ static void sky2_power_on(struct sky2_hw *hw) sky2_write8(hw, B2_Y2_CLK_GATE, 0); if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) { - u32 reg1; + u32 reg; - sky2_pci_write32(hw, PCI_DEV_REG3, 0); - reg1 = sky2_pci_read32(hw, PCI_DEV_REG4); - reg1 &= P_ASPM_CONTROL_MSK; - sky2_pci_write32(hw, PCI_DEV_REG4, reg1); - sky2_pci_write32(hw, PCI_DEV_REG5, 0); + reg = sky2_pci_read32(hw, PCI_DEV_REG4); + /* set all bits to 0 except bits 15..12 and 8 */ + reg &= P_ASPM_CONTROL_MSK; + sky2_pci_write32(hw, PCI_DEV_REG4, reg); + + reg = sky2_pci_read32(hw, PCI_DEV_REG5); + /* set all bits to 0 except bits 28 & 27 */ + reg &= P_CTL_TIM_VMAIN_AV_MSK; + sky2_pci_write32(hw, PCI_DEV_REG5, reg); + + sky2_pci_write32(hw, PCI_CFG_REG_1, 0); + + /* Enable workaround for dev 4.107 on Yukon-Ultra & Extreme */ + reg = sky2_read32(hw, B2_GP_IO); + reg |= GLB_GPIO_STAT_RACE_DIS; + sky2_write32(hw, B2_GP_IO, reg); } } @@ -650,6 +661,30 @@ static void sky2_wol_init(struct sky2_port *sky2) } +static void sky2_set_tx_stfwd(struct sky2_hw *hw, unsigned port) +{ + if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev != CHIP_REV_YU_EX_A0) { + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_STFW_ENA | + (hw->dev[port]->mtu > ETH_DATA_LEN) ? TX_JUMBO_ENA : TX_JUMBO_DIS); + } else { + if (hw->dev[port]->mtu > ETH_DATA_LEN) { + /* set Tx GMAC FIFO Almost Empty Threshold */ + sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), + (ECU_JUMBO_WM << 16) | ECU_AE_THR); + + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_JUMBO_ENA | TX_STFW_DIS); + + /* Can't do offload because of lack of store/forward */ + hw->dev[port]->features &= ~(NETIF_F_TSO | NETIF_F_SG + | NETIF_F_ALL_CSUM); + } else + sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), + TX_JUMBO_DIS | TX_STFW_ENA); + } +} + static void sky2_mac_init(struct sky2_hw *hw, unsigned port) { struct sky2_port *sky2 = netdev_priv(hw->dev[port]); @@ -730,8 +765,11 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) /* Configure Rx MAC FIFO */ sky2_write8(hw, SK_REG(port, RX_GMF_CTRL_T), GMF_RST_CLR); - sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), - GMF_OPER_ON | GMF_RX_F_FL_ON); + reg = GMF_OPER_ON | GMF_RX_F_FL_ON; + if (hw->chip_id == CHIP_ID_YUKON_EX) + reg |= GMF_RX_OVER_ON; + + sky2_write32(hw, SK_REG(port, RX_GMF_CTRL_T), reg); /* Flush Rx MAC FIFO on any flow control or error */ sky2_write16(hw, SK_REG(port, RX_GMF_FL_MSK), GMR_FS_ANY_ERR); @@ -747,16 +785,7 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port) sky2_write8(hw, SK_REG(port, RX_GMF_LP_THR), 768/8); sky2_write8(hw, SK_REG(port, RX_GMF_UP_THR), 1024/8); - /* set Tx GMAC FIFO Almost Empty Threshold */ - sky2_write32(hw, SK_REG(port, TX_GMF_AE_THR), - (ECU_JUMBO_WM << 16) | ECU_AE_THR); - - if (hw->dev[port]->mtu > ETH_DATA_LEN) - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_ENA | TX_STFW_DIS); - else - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_DIS | TX_STFW_ENA); + sky2_set_tx_stfwd(hw, port); } } @@ -939,14 +968,16 @@ static void rx_set_checksum(struct sky2_port *sky2) { struct sky2_rx_le *le; - le = sky2_next_rx(sky2); - le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN); - le->ctrl = 0; - le->opcode = OP_TCPSTART | HW_OWNER; + if (sky2->hw->chip_id != CHIP_ID_YUKON_EX) { + le = sky2_next_rx(sky2); + le->addr = cpu_to_le32((ETH_HLEN << 16) | ETH_HLEN); + le->ctrl = 0; + le->opcode = OP_TCPSTART | HW_OWNER; - sky2_write32(sky2->hw, - Q_ADDR(rxqaddr[sky2->port], Q_CSR), - sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); + sky2_write32(sky2->hw, + Q_ADDR(rxqaddr[sky2->port], Q_CSR), + sky2->rx_csum ? BMU_ENA_RX_CHKSUM : BMU_DIS_RX_CHKSUM); + } } @@ -1134,7 +1165,7 @@ static int sky2_rx_start(struct sky2_port *sky2) if (hw->chip_id == CHIP_ID_YUKON_EC_U && (hw->chip_rev == CHIP_REV_YU_EC_U_A1 || hw->chip_rev == CHIP_REV_YU_EC_U_B0)) - sky2_write32(hw, Q_ADDR(rxq, Q_F), F_M_RX_RAM_DIS); + sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS); sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1); @@ -1285,6 +1316,10 @@ static int sky2_up(struct net_device *dev) sky2_qset(hw, txqaddr[port]); + /* This is copied from sk98lin 10.0.5.3; no one tells me about erratta's */ + if (hw->chip_id == CHIP_ID_YUKON_EX && hw->chip_rev == CHIP_REV_YU_EX_B0) + sky2_write32(hw, Q_ADDR(txqaddr[port], Q_TEST), F_TX_CHK_AUTO_OFF); + /* Set almost empty threshold */ if (hw->chip_id == CHIP_ID_YUKON_EC_U && hw->chip_rev == CHIP_REV_YU_EC_U_A0) @@ -1393,14 +1428,16 @@ static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev) /* Check for TCP Segmentation Offload */ mss = skb_shinfo(skb)->gso_size; if (mss != 0) { - mss += tcp_optlen(skb); /* TCP options */ - mss += ip_hdrlen(skb) + sizeof(struct tcphdr); - mss += ETH_HLEN; - - if (mss != sky2->tx_last_mss) { - le = get_tx_le(sky2); - le->addr = cpu_to_le32(mss); - le->opcode = OP_LRGLEN | HW_OWNER; + if (hw->chip_id != CHIP_ID_YUKON_EX) + mss += ETH_HLEN + ip_hdrlen(skb) + tcp_hdrlen(skb); + + if (mss != sky2->tx_last_mss) { + le = get_tx_le(sky2); + le->addr = cpu_to_le32(mss); + if (hw->chip_id == CHIP_ID_YUKON_EX) + le->opcode = OP_MSS | HW_OWNER; + else + le->opcode = OP_LRGLEN | HW_OWNER; sky2->tx_last_mss = mss; } } @@ -1422,24 +1459,30 @@ static int sky2_xmit_frame(struct sk_buff *skb, struct net_device *dev) /* Handle TCP checksum offload */ if (skb->ip_summed == CHECKSUM_PARTIAL) { - const unsigned offset = skb_transport_offset(skb); - u32 tcpsum; - - tcpsum = offset << 16; /* sum start */ - tcpsum |= offset + skb->csum_offset; /* sum write */ - - ctrl |= CALSUM | WR_SUM | INIT_SUM | LOCK_SUM; - if (ip_hdr(skb)->protocol == IPPROTO_UDP) - ctrl |= UDPTCP; - - if (tcpsum != sky2->tx_tcpsum) { - sky2->tx_tcpsum = tcpsum; - - le = get_tx_le(sky2); - le->addr = cpu_to_le32(tcpsum); - le->length = 0; /* initial checksum value */ - le->ctrl = 1; /* one packet */ - le->opcode = OP_TCPLISW | HW_OWNER; + /* On Yukon EX (some versions) encoding change. */ + if (hw->chip_id == CHIP_ID_YUKON_EX + && hw->chip_rev != CHIP_REV_YU_EX_B0) + ctrl |= CALSUM; /* auto checksum */ + else { + const unsigned offset = skb_transport_offset(skb); + u32 tcpsum; + + tcpsum = offset << 16; /* sum start */ + tcpsum |= offset + skb->csum_offset; /* sum write */ + + ctrl |= CALSUM | WR_SUM | INIT_SUM | LOCK_SUM; + if (ip_hdr(skb)->protocol == IPPROTO_UDP) + ctrl |= UDPTCP; + + if (tcpsum != sky2->tx_tcpsum) { + sky2->tx_tcpsum = tcpsum; + + le = get_tx_le(sky2); + le->addr = cpu_to_le32(tcpsum); + le->length = 0; /* initial checksum value */ + le->ctrl = 1; /* one packet */ + le->opcode = OP_TCPLISW | HW_OWNER; + } } } @@ -1913,15 +1956,8 @@ static int sky2_change_mtu(struct net_device *dev, int new_mtu) synchronize_irq(hw->pdev->irq); - if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) { - if (new_mtu > ETH_DATA_LEN) { - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_ENA | TX_STFW_DIS); - dev->features &= NETIF_F_TSO | NETIF_F_SG | NETIF_F_IP_CSUM; - } else - sky2_write32(hw, SK_REG(port, TX_GMF_CTRL_T), - TX_JUMBO_DIS | TX_STFW_ENA); - } + if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) + sky2_set_tx_stfwd(hw, port); ctl = gma_read16(hw, port, GM_GP_CTRL); gma_write16(hw, port, GM_GP_CTRL, ctl & ~GM_GPCR_RX_ENA); @@ -2118,6 +2154,7 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) while (hw->st_idx != hwidx) { struct sky2_status_le *le = hw->st_le + hw->st_idx; + unsigned port = le->css & CSS_LINK_BIT; struct net_device *dev; struct sk_buff *skb; u32 status; @@ -2125,9 +2162,7 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) hw->st_idx = RING_NEXT(hw->st_idx, STATUS_RING_SIZE); - BUG_ON(le->link >= 2); - dev = hw->dev[le->link]; - + dev = hw->dev[port]; sky2 = netdev_priv(dev); length = le16_to_cpu(le->length); status = le32_to_cpu(le->status); @@ -2140,6 +2175,16 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) goto force_update; } + /* This chip reports checksum status differently */ + if (hw->chip_id == CHIP_ID_YUKON_EX) { + if (sky2->rx_csum && + (le->css & (CSS_ISIPV4 | CSS_ISIPV6)) && + (le->css & CSS_TCPUDPCSOK)) + skb->ip_summed = CHECKSUM_UNNECESSARY; + else + skb->ip_summed = CHECKSUM_NONE; + } + skb->protocol = eth_type_trans(skb, dev); sky2->net_stats.rx_packets++; sky2->net_stats.rx_bytes += skb->len; @@ -2155,10 +2200,10 @@ static int sky2_status_intr(struct sky2_hw *hw, int to_do) netif_receive_skb(skb); /* Update receiver after 16 frames */ - if (++buf_write[le->link] == RX_BUF_WRITE) { + if (++buf_write[port] == RX_BUF_WRITE) { force_update: - sky2_put_idx(hw, rxqaddr[le->link], sky2->rx_put); - buf_write[le->link] = 0; + sky2_put_idx(hw, rxqaddr[port], sky2->rx_put); + buf_write[port] = 0; } /* Stop after net poll weight */ @@ -2179,6 +2224,9 @@ force_update: if (!sky2->rx_csum) break; + if (hw->chip_id == CHIP_ID_YUKON_EX) + break; + /* Both checksum counters are programmed to start at * the same offset, so unless there is a problem they * should match. This failure is an early indication that @@ -2194,7 +2242,7 @@ force_update: dev->name, status); sky2->rx_csum = 0; sky2_write32(sky2->hw, - Q_ADDR(rxqaddr[le->link], Q_CSR), + Q_ADDR(rxqaddr[port], Q_CSR), BMU_DIS_RX_CHKSUM); } break; @@ -2513,6 +2561,9 @@ static int __devinit sky2_init(struct sky2_hw *hw) { u8 t8; + /* Enable all clocks */ + sky2_pci_write32(hw, PCI_DEV_REG3, 0); + sky2_write8(hw, B0_CTST, CS_RST_CLR); hw->chip_id = sky2_read8(hw, B2_CHIP_ID); @@ -2522,14 +2573,6 @@ static int __devinit sky2_init(struct sky2_hw *hw) return -EOPNOTSUPP; } - if (hw->chip_id == CHIP_ID_YUKON_EX) - dev_warn(&hw->pdev->dev, "this driver not yet tested on this chip type\n" - "Please report success or failure to <netdev@vger.kernel.org>\n"); - - /* Make sure and enable all clocks */ - if (hw->chip_id == CHIP_ID_YUKON_EX || hw->chip_id == CHIP_ID_YUKON_EC_U) - sky2_pci_write32(hw, PCI_DEV_REG3, 0); - hw->chip_rev = (sky2_read8(hw, B2_MAC_CFG) & CFG_CHIP_R_MSK) >> 4; /* This rev is really old, and requires untested workarounds */ @@ -2589,6 +2632,11 @@ static void sky2_reset(struct sky2_hw *hw) for (i = 0; i < hw->ports; i++) { sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_SET); sky2_write8(hw, SK_REG(i, GMAC_LINK_CTRL), GMLC_RST_CLR); + + if (hw->chip_id == CHIP_ID_YUKON_EX) + sky2_write16(hw, SK_REG(i, GMAC_CTRL), + GMC_BYP_MACSECRX_ON | GMC_BYP_MACSECTX_ON + | GMC_BYP_RETR_ON); } sky2_write8(hw, B2_TST_CTRL1, TST_CFG_WRITE_OFF); @@ -2735,7 +2783,7 @@ static int sky2_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) sky2->wol = wol->wolopts; - if (hw->chip_id == CHIP_ID_YUKON_EC_U) + if (hw->chip_id == CHIP_ID_YUKON_EC_U || hw->chip_id == CHIP_ID_YUKON_EX) sky2_write32(hw, B0_CTST, sky2->wol ? Y2_HW_WOL_ON : Y2_HW_WOL_OFF); @@ -3330,7 +3378,7 @@ static int sky2_get_regs_len(struct net_device *dev) /* * Returns copy of control register region - * Note: access to the RAM address register set will cause timeouts. + * Note: ethtool_get_regs always provides full size (16k) buffer */ static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs, void *p) @@ -3338,15 +3386,19 @@ static void sky2_get_regs(struct net_device *dev, struct ethtool_regs *regs, const struct sky2_port *sky2 = netdev_priv(dev); const void __iomem *io = sky2->hw->regs; - BUG_ON(regs->len < B3_RI_WTO_R1); regs->version = 1; memset(p, 0, regs->len); memcpy_fromio(p, io, B3_RAM_ADDR); - memcpy_fromio(p + B3_RI_WTO_R1, - io + B3_RI_WTO_R1, - regs->len - B3_RI_WTO_R1); + /* skip diagnostic ram region */ + memcpy_fromio(p + B3_RI_WTO_R1, io + B3_RI_WTO_R1, 0x2000 - B3_RI_WTO_R1); + + /* copy GMAC registers */ + memcpy_fromio(p + BASE_GMAC_1, io + BASE_GMAC_1, 0x1000); + if (sky2->hw->ports > 1) + memcpy_fromio(p + BASE_GMAC_2, io + BASE_GMAC_2, 0x1000); + } /* In order to do Jumbo packets on these chips, need to turn off the @@ -3357,9 +3409,7 @@ static int no_tx_offload(struct net_device *dev) const struct sky2_port *sky2 = netdev_priv(dev); const struct sky2_hw *hw = sky2->hw; - return dev->mtu > ETH_DATA_LEN && - (hw->chip_id == CHIP_ID_YUKON_EX - || hw->chip_id == CHIP_ID_YUKON_EC_U); + return dev->mtu > ETH_DATA_LEN && hw->chip_id == CHIP_ID_YUKON_EC_U; } static int sky2_set_tx_csum(struct net_device *dev, u32 data) diff --git a/drivers/net/sky2.h b/drivers/net/sky2.h index b8c4a3b5ead..8df4643493d 100644 --- a/drivers/net/sky2.h +++ b/drivers/net/sky2.h @@ -14,6 +14,8 @@ enum { PCI_DEV_REG3 = 0x80, PCI_DEV_REG4 = 0x84, PCI_DEV_REG5 = 0x88, + PCI_CFG_REG_0 = 0x90, + PCI_CFG_REG_1 = 0x94, }; enum { @@ -28,6 +30,7 @@ enum { enum pci_dev_reg_1 { PCI_Y2_PIG_ENA = 1<<31, /* Enable Plug-in-Go (YUKON-2) */ PCI_Y2_DLL_DIS = 1<<30, /* Disable PCI DLL (YUKON-2) */ + PCI_SW_PWR_ON_RST= 1<<30, /* SW Power on Reset (Yukon-EX) */ PCI_Y2_PHY2_COMA = 1<<29, /* Set PHY 2 to Coma Mode (YUKON-2) */ PCI_Y2_PHY1_COMA = 1<<28, /* Set PHY 1 to Coma Mode (YUKON-2) */ PCI_Y2_PHY2_POWD = 1<<27, /* Set PHY 2 to Power Down (YUKON-2) */ @@ -67,6 +70,80 @@ enum pci_dev_reg_4 { | P_ASPM_CLKRUN_REQUEST | P_ASPM_INT_FIFO_EMPTY, }; +/* PCI_OUR_REG_5 32 bit Our Register 5 (Yukon-ECU only) */ +enum pci_dev_reg_5 { + /* Bit 31..27: for A3 & later */ + P_CTL_DIV_CORE_CLK_ENA = 1<<31, /* Divide Core Clock Enable */ + P_CTL_SRESET_VMAIN_AV = 1<<30, /* Soft Reset for Vmain_av De-Glitch */ + P_CTL_BYPASS_VMAIN_AV = 1<<29, /* Bypass En. for Vmain_av De-Glitch */ + P_CTL_TIM_VMAIN_AV_MSK = 3<<27, /* Bit 28..27: Timer Vmain_av Mask */ + /* Bit 26..16: Release Clock on Event */ + P_REL_PCIE_RST_DE_ASS = 1<<26, /* PCIe Reset De-Asserted */ + P_REL_GPHY_REC_PACKET = 1<<25, /* GPHY Received Packet */ + P_REL_INT_FIFO_N_EMPTY = 1<<24, /* Internal FIFO Not Empty */ + P_REL_MAIN_PWR_AVAIL = 1<<23, /* Main Power Available */ + P_REL_CLKRUN_REQ_REL = 1<<22, /* CLKRUN Request Release */ + P_REL_PCIE_RESET_ASS = 1<<21, /* PCIe Reset Asserted */ + P_REL_PME_ASSERTED = 1<<20, /* PME Asserted */ + P_REL_PCIE_EXIT_L1_ST = 1<<19, /* PCIe Exit L1 State */ + P_REL_LOADER_NOT_FIN = 1<<18, /* EPROM Loader Not Finished */ + P_REL_PCIE_RX_EX_IDLE = 1<<17, /* PCIe Rx Exit Electrical Idle State */ + P_REL_GPHY_LINK_UP = 1<<16, /* GPHY Link Up */ + + /* Bit 10.. 0: Mask for Gate Clock */ + P_GAT_PCIE_RST_ASSERTED = 1<<10,/* PCIe Reset Asserted */ + P_GAT_GPHY_N_REC_PACKET = 1<<9, /* GPHY Not Received Packet */ + P_GAT_INT_FIFO_EMPTY = 1<<8, /* Internal FIFO Empty */ + P_GAT_MAIN_PWR_N_AVAIL = 1<<7, /* Main Power Not Available */ + P_GAT_CLKRUN_REQ_REL = 1<<6, /* CLKRUN Not Requested */ + P_GAT_PCIE_RESET_ASS = 1<<5, /* PCIe Reset Asserted */ + P_GAT_PME_DE_ASSERTED = 1<<4, /* PME De-Asserted */ + P_GAT_PCIE_ENTER_L1_ST = 1<<3, /* PCIe Enter L1 State */ + P_GAT_LOADER_FINISHED = 1<<2, /* EPROM Loader Finished */ + P_GAT_PCIE_RX_EL_IDLE = 1<<1, /* PCIe Rx Electrical Idle State */ + P_GAT_GPHY_LINK_DOWN = 1<<0, /* GPHY Link Down */ + + PCIE_OUR5_EVENT_CLK_D3_SET = P_REL_GPHY_REC_PACKET | + P_REL_INT_FIFO_N_EMPTY | + P_REL_PCIE_EXIT_L1_ST | + P_REL_PCIE_RX_EX_IDLE | + P_GAT_GPHY_N_REC_PACKET | + P_GAT_INT_FIFO_EMPTY | + P_GAT_PCIE_ENTER_L1_ST | + P_GAT_PCIE_RX_EL_IDLE, +}; + +#/* PCI_CFG_REG_1 32 bit Config Register 1 (Yukon-Ext only) */ +enum pci_cfg_reg1 { + P_CF1_DIS_REL_EVT_RST = 1<<24, /* Dis. Rel. Event during PCIE reset */ + /* Bit 23..21: Release Clock on Event */ + P_CF1_REL_LDR_NOT_FIN = 1<<23, /* EEPROM Loader Not Finished */ + P_CF1_REL_VMAIN_AVLBL = 1<<22, /* Vmain available */ + P_CF1_REL_PCIE_RESET = 1<<21, /* PCI-E reset */ + /* Bit 20..18: Gate Clock on Event */ + P_CF1_GAT_LDR_NOT_FIN = 1<<20, /* EEPROM Loader Finished */ + P_CF1_GAT_PCIE_RX_IDLE = 1<<19, /* PCI-E Rx Electrical idle */ + P_CF1_GAT_PCIE_RESET = 1<<18, /* PCI-E Reset */ + P_CF1_PRST_PHY_CLKREQ = 1<<17, /* Enable PCI-E rst & PM2PHY gen. CLKREQ */ + P_CF1_PCIE_RST_CLKREQ = 1<<16, /* Enable PCI-E rst generate CLKREQ */ + + P_CF1_ENA_CFG_LDR_DONE = 1<<8, /* Enable core level Config loader done */ + + P_CF1_ENA_TXBMU_RD_IDLE = 1<<1, /* Enable TX BMU Read IDLE for ASPM */ + P_CF1_ENA_TXBMU_WR_IDLE = 1<<0, /* Enable TX BMU Write IDLE for ASPM */ + + PCIE_CFG1_EVENT_CLK_D3_SET = P_CF1_DIS_REL_EVT_RST | + P_CF1_REL_LDR_NOT_FIN | + P_CF1_REL_VMAIN_AVLBL | + P_CF1_REL_PCIE_RESET | + P_CF1_GAT_LDR_NOT_FIN | + P_CF1_GAT_PCIE_RESET | + P_CF1_PRST_PHY_CLKREQ | + P_CF1_ENA_CFG_LDR_DONE | + P_CF1_ENA_TXBMU_RD_IDLE | + P_CF1_ENA_TXBMU_WR_IDLE, +}; + #define PCI_STATUS_ERROR_BITS (PCI_STATUS_DETECTED_PARITY | \ PCI_STATUS_SIG_SYSTEM_ERROR | \ @@ -364,6 +441,20 @@ enum { TST_CFG_WRITE_OFF= 1<<0, /* Disable Config Reg WR */ }; +/* B2_GPIO */ +enum { + GLB_GPIO_CLK_DEB_ENA = 1<<31, /* Clock Debug Enable */ + GLB_GPIO_CLK_DBG_MSK = 0xf<<26, /* Clock Debug */ + + GLB_GPIO_INT_RST_D3_DIS = 1<<15, /* Disable Internal Reset After D3 to D0 */ + GLB_GPIO_LED_PAD_SPEED_UP = 1<<14, /* LED PAD Speed Up */ + GLB_GPIO_STAT_RACE_DIS = 1<<13, /* Status Race Disable */ + GLB_GPIO_TEST_SEL_MSK = 3<<11, /* Testmode Select */ + GLB_GPIO_TEST_SEL_BASE = 1<<11, + GLB_GPIO_RAND_ENA = 1<<10, /* Random Enable */ + GLB_GPIO_RAND_BIT_1 = 1<<9, /* Random Bit 1 */ +}; + /* B2_MAC_CFG 8 bit MAC Configuration / Chip Revision */ enum { CFG_CHIP_R_MSK = 0xf<<4, /* Bit 7.. 4: Chip Revision */ @@ -392,6 +483,11 @@ enum { CHIP_REV_YU_FE_A2 = 2, }; +enum yukon_ex_rev { + CHIP_REV_YU_EX_A0 = 1, + CHIP_REV_YU_EX_B0 = 2, +}; + /* B2_Y2_CLK_GATE 8 bit Clock Gating (Yukon-2 only) */ enum { @@ -515,23 +611,15 @@ enum { enum { B8_Q_REGS = 0x0400, /* base of Queue registers */ Q_D = 0x00, /* 8*32 bit Current Descriptor */ - Q_DA_L = 0x20, /* 32 bit Current Descriptor Address Low dWord */ - Q_DA_H = 0x24, /* 32 bit Current Descriptor Address High dWord */ + Q_VLAN = 0x20, /* 16 bit Current VLAN Tag */ + Q_DONE = 0x24, /* 16 bit Done Index */ Q_AC_L = 0x28, /* 32 bit Current Address Counter Low dWord */ Q_AC_H = 0x2c, /* 32 bit Current Address Counter High dWord */ Q_BC = 0x30, /* 32 bit Current Byte Counter */ Q_CSR = 0x34, /* 32 bit BMU Control/Status Register */ - Q_F = 0x38, /* 32 bit Flag Register */ - Q_T1 = 0x3c, /* 32 bit Test Register 1 */ - Q_T1_TR = 0x3c, /* 8 bit Test Register 1 Transfer SM */ - Q_T1_WR = 0x3d, /* 8 bit Test Register 1 Write Descriptor SM */ - Q_T1_RD = 0x3e, /* 8 bit Test Register 1 Read Descriptor SM */ - Q_T1_SV = 0x3f, /* 8 bit Test Register 1 Supervisor SM */ - Q_T2 = 0x40, /* 32 bit Test Register 2 */ - Q_T3 = 0x44, /* 32 bit Test Register 3 */ + Q_TEST = 0x38, /* 32 bit Test/Control Register */ /* Yukon-2 */ - Q_DONE = 0x24, /* 16 bit Done Index (Yukon-2 only) */ Q_WM = 0x40, /* 16 bit FIFO Watermark */ Q_AL = 0x42, /* 8 bit FIFO Alignment */ Q_RSP = 0x44, /* 16 bit FIFO Read Shadow Pointer */ @@ -545,15 +633,16 @@ enum { }; #define Q_ADDR(reg, offs) (B8_Q_REGS + (reg) + (offs)) -/* Q_F 32 bit Flag Register */ +/* Q_TEST 32 bit Test Register */ enum { - F_ALM_FULL = 1<<27, /* Rx FIFO: almost full */ - F_EMPTY = 1<<27, /* Tx FIFO: empty flag */ - F_FIFO_EOF = 1<<26, /* Tag (EOF Flag) bit in FIFO */ - F_WM_REACHED = 1<<25, /* Watermark reached */ + /* Transmit */ + F_TX_CHK_AUTO_OFF = 1<<31, /* Tx checksum auto calc off (Yukon EX) */ + F_TX_CHK_AUTO_ON = 1<<30, /* Tx checksum auto calc off (Yukon EX) */ + + /* Receive */ F_M_RX_RAM_DIS = 1<<24, /* MAC Rx RAM Read Port disable */ - F_FIFO_LEVEL = 0x1fL<<16, /* Bit 23..16: # of Qwords in FIFO */ - F_WATER_MARK = 0x0007ffL, /* Bit 10.. 0: Watermark */ + + /* Hardware testbits not used */ }; /* Queue Prefetch Unit Offsets, use Y2_QADDR() to address (Yukon-2 only)*/ @@ -1608,6 +1697,16 @@ enum { RX_VLAN_STRIP_ON = 1<<25, /* enable VLAN stripping */ RX_VLAN_STRIP_OFF = 1<<24, /* disable VLAN stripping */ + RX_MACSEC_FLUSH_ON = 1<<23, + RX_MACSEC_FLUSH_OFF = 1<<22, + RX_MACSEC_ASF_FLUSH_ON = 1<<21, + RX_MACSEC_ASF_FLUSH_OFF = 1<<20, + + GMF_RX_OVER_ON = 1<<19, /* enable flushing on receive overrun */ + GMF_RX_OVER_OFF = 1<<18, /* disable flushing on receive overrun */ + GMF_ASF_RX_OVER_ON = 1<<17, /* enable flushing of ASF when overrun */ + GMF_ASF_RX_OVER_OFF = 1<<16, /* disable flushing of ASF when overrun */ + GMF_WP_TST_ON = 1<<14, /* Write Pointer Test On */ GMF_WP_TST_OFF = 1<<13, /* Write Pointer Test Off */ GMF_WP_STEP = 1<<12, /* Write Pointer Step/Increment */ @@ -1720,6 +1819,15 @@ enum { /* GMAC_CTRL 32 bit GMAC Control Reg (YUKON only) */ enum { + GMC_SET_RST = 1<<15,/* MAC SEC RST */ + GMC_SEC_RST_OFF = 1<<14,/* MAC SEC RSt OFF */ + GMC_BYP_MACSECRX_ON = 1<<13,/* Bypass macsec RX */ + GMC_BYP_MACSECRX_OFF= 1<<12,/* Bypass macsec RX off */ + GMC_BYP_MACSECTX_ON = 1<<11,/* Bypass macsec TX */ + GMC_BYP_MACSECTX_OFF= 1<<10,/* Bypass macsec TX off*/ + GMC_BYP_RETR_ON = 1<<9, /* Bypass retransmit FIFO On */ + GMC_BYP_RETR_OFF= 1<<8, /* Bypass retransmit FIFO Off */ + GMC_H_BURST_ON = 1<<7, /* Half Duplex Burst Mode On */ GMC_H_BURST_OFF = 1<<6, /* Half Duplex Burst Mode Off */ GMC_F_LOOPB_ON = 1<<5, /* FIFO Loopback On */ @@ -1805,9 +1913,13 @@ enum { OP_ADDR64VLAN = OP_ADDR64 | OP_VLAN, OP_LRGLEN = 0x24, OP_LRGLENVLAN = OP_LRGLEN | OP_VLAN, + OP_MSS = 0x28, + OP_MSSVLAN = OP_MSS | OP_VLAN, + OP_BUFFER = 0x40, OP_PACKET = 0x41, OP_LARGESEND = 0x43, + OP_LSOV2 = 0x45, /* YUKON-2 STATUS opcodes defines */ OP_RXSTAT = 0x60, @@ -1818,6 +1930,19 @@ enum { OP_RXTIMEVLAN = OP_RXTIMESTAMP | OP_RXVLAN, OP_RSS_HASH = 0x65, OP_TXINDEXLE = 0x68, + OP_MACSEC = 0x6c, + OP_PUTIDX = 0x70, +}; + +enum status_css { + CSS_TCPUDPCSOK = 1<<7, /* TCP / UDP checksum is ok */ + CSS_ISUDP = 1<<6, /* packet is a UDP packet */ + CSS_ISTCP = 1<<5, /* packet is a TCP packet */ + CSS_ISIPFRAG = 1<<4, /* packet is a TCP/UDP frag, CS calc not done */ + CSS_ISIPV6 = 1<<3, /* packet is a IPv6 packet */ + CSS_IPV4CSUMOK = 1<<2, /* IP v4: TCP header checksum is ok */ + CSS_ISIPV4 = 1<<1, /* packet is a IPv4 packet */ + CSS_LINK_BIT = 1<<0, /* port number (legacy) */ }; /* Yukon 2 hardware interface */ @@ -1838,7 +1963,7 @@ struct sky2_rx_le { struct sky2_status_le { __le32 status; /* also checksum */ __le16 length; /* also vlan tag */ - u8 link; + u8 css; u8 opcode; } __attribute((packed)); diff --git a/drivers/net/sni_82596.c b/drivers/net/sni_82596.c new file mode 100644 index 00000000000..2cf6794acb4 --- /dev/null +++ b/drivers/net/sni_82596.c @@ -0,0 +1,185 @@ +/* + * sni_82596.c -- driver for intel 82596 ethernet controller, as + * used in older SNI RM machines + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/errno.h> +#include <linux/ioport.h> +#include <linux/slab.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/netdevice.h> +#include <linux/etherdevice.h> +#include <linux/skbuff.h> +#include <linux/init.h> +#include <linux/types.h> +#include <linux/bitops.h> +#include <linux/platform_device.h> +#include <linux/io.h> +#include <linux/irq.h> + +#define SNI_82596_DRIVER_VERSION "SNI RM 82596 driver - Revision: 0.01" + +static const char sni_82596_string[] = "snirm_82596"; + +#define DMA_ALLOC dma_alloc_coherent +#define DMA_FREE dma_free_coherent +#define DMA_WBACK(priv, addr, len) do { } while (0) +#define DMA_INV(priv, addr, len) do { } while (0) +#define DMA_WBACK_INV(priv, addr, len) do { } while (0) + +#define SYSBUS 0x00004400 + +/* big endian CPU, 82596 little endian */ +#define SWAP32(x) cpu_to_le32((u32)(x)) +#define SWAP16(x) cpu_to_le16((u16)(x)) + +#define OPT_MPU_16BIT 0x01 + +#include "lib82596.c" + +MODULE_AUTHOR("Thomas Bogendoerfer"); +MODULE_DESCRIPTION("i82596 driver"); +MODULE_LICENSE("GPL"); +module_param(i596_debug, int, 0); +MODULE_PARM_DESC(i596_debug, "82596 debug mask"); + +static inline void ca(struct net_device *dev) +{ + struct i596_private *lp = netdev_priv(dev); + + writel(0, lp->ca); +} + + +static void mpu_port(struct net_device *dev, int c, dma_addr_t x) +{ + struct i596_private *lp = netdev_priv(dev); + + u32 v = (u32) (c) | (u32) (x); + + if (lp->options & OPT_MPU_16BIT) { + writew(v & 0xffff, lp->mpu_port); + wmb(); /* order writes to MPU port */ + udelay(1); + writew(v >> 16, lp->mpu_port); + } else { + writel(v, lp->mpu_port); + wmb(); /* order writes to MPU port */ + udelay(1); + writel(v, lp->mpu_port); + } +} + + +static int __devinit sni_82596_probe(struct platform_device *dev) +{ + struct net_device *netdevice; + struct i596_private *lp; + struct resource *res, *ca, *idprom, *options; + int retval = -ENOMEM; + void __iomem *mpu_addr; + void __iomem *ca_addr; + u8 __iomem *eth_addr; + + res = platform_get_resource(dev, IORESOURCE_MEM, 0); + ca = platform_get_resource(dev, IORESOURCE_MEM, 1); + options = platform_get_resource(dev, 0, 0); + idprom = platform_get_resource(dev, IORESOURCE_MEM, 2); + if (!res || !ca || !options || !idprom) + return -ENODEV; + mpu_addr = ioremap_nocache(res->start, 4); + if (!mpu_addr) + return -ENOMEM; + ca_addr = ioremap_nocache(ca->start, 4); + if (!ca_addr) + goto probe_failed_free_mpu; + + printk(KERN_INFO "Found i82596 at 0x%x\n", res->start); + + netdevice = alloc_etherdev(sizeof(struct i596_private)); + if (!netdevice) + goto probe_failed_free_ca; + + SET_NETDEV_DEV(netdevice, &dev->dev); + platform_set_drvdata (dev, netdevice); + + netdevice->base_addr = res->start; + netdevice->irq = platform_get_irq(dev, 0); + + eth_addr = ioremap_nocache(idprom->start, 0x10); + if (!eth_addr) + goto probe_failed; + + /* someone seems to like messed up stuff */ + netdevice->dev_addr[0] = readb(eth_addr + 0x0b); + netdevice->dev_addr[1] = readb(eth_addr + 0x0a); + netdevice->dev_addr[2] = readb(eth_addr + 0x09); + netdevice->dev_addr[3] = readb(eth_addr + 0x08); + netdevice->dev_addr[4] = readb(eth_addr + 0x07); + netdevice->dev_addr[5] = readb(eth_addr + 0x06); + iounmap(eth_addr); + + if (!netdevice->irq) { + printk(KERN_ERR "%s: IRQ not found for i82596 at 0x%lx\n", + __FILE__, netdevice->base_addr); + goto probe_failed; + } + + lp = netdev_priv(netdevice); + lp->options = options->flags & IORESOURCE_BITS; + lp->ca = ca_addr; + lp->mpu_port = mpu_addr; + + retval = i82596_probe(netdevice); + if (retval == 0) + return 0; + +probe_failed: + free_netdev(netdevice); +probe_failed_free_ca: + iounmap(ca_addr); +probe_failed_free_mpu: + iounmap(mpu_addr); + return retval; +} + +static int __devexit sni_82596_driver_remove(struct platform_device *pdev) +{ + struct net_device *dev = platform_get_drvdata(pdev); + struct i596_private *lp = netdev_priv(dev); + + unregister_netdev(dev); + DMA_FREE(dev->dev.parent, sizeof(struct i596_private), + lp->dma, lp->dma_addr); + iounmap(lp->ca); + iounmap(lp->mpu_port); + free_netdev (dev); + return 0; +} + +static struct platform_driver sni_82596_driver = { + .probe = sni_82596_probe, + .remove = __devexit_p(sni_82596_driver_remove), + .driver = { + .name = sni_82596_string, + }, +}; + +static int __devinit sni_82596_init(void) +{ + printk(KERN_INFO SNI_82596_DRIVER_VERSION "\n"); + return platform_driver_register(&sni_82596_driver); +} + + +static void __exit sni_82596_exit(void) +{ + platform_driver_unregister(&sni_82596_driver); +} + +module_init(sni_82596_init); +module_exit(sni_82596_exit); diff --git a/drivers/net/spider_net.c b/drivers/net/spider_net.c index 7a4aa6a9f94..f5abb5279d4 100644 --- a/drivers/net/spider_net.c +++ b/drivers/net/spider_net.c @@ -434,7 +434,8 @@ spider_net_prepare_rx_descr(struct spider_net_card *card, bufsize + SPIDER_NET_RXBUF_ALIGN - 1); if (!descr->skb) { if (netif_msg_rx_err(card) && net_ratelimit()) - pr_err("Not enough memory to allocate rx buffer\n"); + dev_err(&card->netdev->dev, + "Not enough memory to allocate rx buffer\n"); card->spider_stats.alloc_rx_skb_error++; return -ENOMEM; } @@ -455,7 +456,7 @@ spider_net_prepare_rx_descr(struct spider_net_card *card, dev_kfree_skb_any(descr->skb); descr->skb = NULL; if (netif_msg_rx_err(card) && net_ratelimit()) - pr_err("Could not iommu-map rx buffer\n"); + dev_err(&card->netdev->dev, "Could not iommu-map rx buffer\n"); card->spider_stats.rx_iommu_map_error++; hwdescr->dmac_cmd_status = SPIDER_NET_DESCR_NOT_IN_USE; } else { @@ -500,6 +501,20 @@ spider_net_enable_rxdmac(struct spider_net_card *card) } /** + * spider_net_disable_rxdmac - disables the receive DMA controller + * @card: card structure + * + * spider_net_disable_rxdmac terminates processing on the DMA controller + * by turing off the DMA controller, with the force-end flag set. + */ +static inline void +spider_net_disable_rxdmac(struct spider_net_card *card) +{ + spider_net_write_reg(card, SPIDER_NET_GDADMACCNTR, + SPIDER_NET_DMA_RX_FEND_VALUE); +} + +/** * spider_net_refill_rx_chain - refills descriptors/skbs in the rx chains * @card: card structure * @@ -655,20 +670,6 @@ write_hash: } /** - * spider_net_disable_rxdmac - disables the receive DMA controller - * @card: card structure - * - * spider_net_disable_rxdmac terminates processing on the DMA controller by - * turing off DMA and issueing a force end - */ -static void -spider_net_disable_rxdmac(struct spider_net_card *card) -{ - spider_net_write_reg(card, SPIDER_NET_GDADMACCNTR, - SPIDER_NET_DMA_RX_FEND_VALUE); -} - -/** * spider_net_prepare_tx_descr - fill tx descriptor with skb data * @card: card structure * @descr: descriptor structure to fill out @@ -692,7 +693,7 @@ spider_net_prepare_tx_descr(struct spider_net_card *card, buf = pci_map_single(card->pdev, skb->data, skb->len, PCI_DMA_TODEVICE); if (pci_dma_mapping_error(buf)) { if (netif_msg_tx_err(card) && net_ratelimit()) - pr_err("could not iommu-map packet (%p, %i). " + dev_err(&card->netdev->dev, "could not iommu-map packet (%p, %i). " "Dropping packet\n", skb->data, skb->len); card->spider_stats.tx_iommu_map_error++; return -ENOMEM; @@ -715,7 +716,7 @@ spider_net_prepare_tx_descr(struct spider_net_card *card, hwdescr->data_status = 0; hwdescr->dmac_cmd_status = - SPIDER_NET_DESCR_CARDOWNED | SPIDER_NET_DMAC_NOCS; + SPIDER_NET_DESCR_CARDOWNED | SPIDER_NET_DMAC_TXFRMTL; spin_unlock_irqrestore(&chain->lock, flags); if (skb->ip_summed == CHECKSUM_PARTIAL) @@ -832,9 +833,8 @@ spider_net_release_tx_chain(struct spider_net_card *card, int brutal) case SPIDER_NET_DESCR_PROTECTION_ERROR: case SPIDER_NET_DESCR_FORCE_END: if (netif_msg_tx_err(card)) - pr_err("%s: forcing end of tx descriptor " - "with status x%02x\n", - card->netdev->name, status); + dev_err(&card->netdev->dev, "forcing end of tx descriptor " + "with status x%02x\n", status); card->netdev_stats.tx_errors++; break; @@ -1022,34 +1022,94 @@ spider_net_pass_skb_up(struct spider_net_descr *descr, netif_receive_skb(skb); } -#ifdef DEBUG static void show_rx_chain(struct spider_net_card *card) { struct spider_net_descr_chain *chain = &card->rx_chain; struct spider_net_descr *start= chain->tail; struct spider_net_descr *descr= start; + struct spider_net_hw_descr *hwd = start->hwdescr; + struct device *dev = &card->netdev->dev; + u32 curr_desc, next_desc; int status; + int tot = 0; int cnt = 0; - int cstat = spider_net_get_descr_status(descr); - printk(KERN_INFO "RX chain tail at descr=%ld\n", - (start - card->descr) - card->tx_chain.num_desc); + int off = start - chain->ring; + int cstat = hwd->dmac_cmd_status; + + dev_info(dev, "Total number of descrs=%d\n", + chain->num_desc); + dev_info(dev, "Chain tail located at descr=%d, status=0x%x\n", + off, cstat); + + curr_desc = spider_net_read_reg(card, SPIDER_NET_GDACTDPA); + next_desc = spider_net_read_reg(card, SPIDER_NET_GDACNEXTDA); + status = cstat; do { - status = spider_net_get_descr_status(descr); + hwd = descr->hwdescr; + off = descr - chain->ring; + status = hwd->dmac_cmd_status; + + if (descr == chain->head) + dev_info(dev, "Chain head is at %d, head status=0x%x\n", + off, status); + + if (curr_desc == descr->bus_addr) + dev_info(dev, "HW curr desc (GDACTDPA) is at %d, status=0x%x\n", + off, status); + + if (next_desc == descr->bus_addr) + dev_info(dev, "HW next desc (GDACNEXTDA) is at %d, status=0x%x\n", + off, status); + + if (hwd->next_descr_addr == 0) + dev_info(dev, "chain is cut at %d\n", off); + if (cstat != status) { - printk(KERN_INFO "Have %d descrs with stat=x%08x\n", cnt, cstat); + int from = (chain->num_desc + off - cnt) % chain->num_desc; + int to = (chain->num_desc + off - 1) % chain->num_desc; + dev_info(dev, "Have %d (from %d to %d) descrs " + "with stat=0x%08x\n", cnt, from, to, cstat); cstat = status; cnt = 0; } + cnt ++; + tot ++; + descr = descr->next; + } while (descr != start); + + dev_info(dev, "Last %d descrs with stat=0x%08x " + "for a total of %d descrs\n", cnt, cstat, tot); + +#ifdef DEBUG + /* Now dump the whole ring */ + descr = start; + do + { + struct spider_net_hw_descr *hwd = descr->hwdescr; + status = spider_net_get_descr_status(hwd); + cnt = descr - chain->ring; + dev_info(dev, "Descr %d stat=0x%08x skb=%p\n", + cnt, status, descr->skb); + dev_info(dev, "bus addr=%08x buf addr=%08x sz=%d\n", + descr->bus_addr, hwd->buf_addr, hwd->buf_size); + dev_info(dev, "next=%08x result sz=%d valid sz=%d\n", + hwd->next_descr_addr, hwd->result_size, + hwd->valid_size); + dev_info(dev, "dmac=%08x data stat=%08x data err=%08x\n", + hwd->dmac_cmd_status, hwd->data_status, + hwd->data_error); + dev_info(dev, "\n"); + descr = descr->next; } while (descr != start); - printk(KERN_INFO "Last %d descrs with stat=x%08x\n", cnt, cstat); -} #endif +} + /** * spider_net_resync_head_ptr - Advance head ptr past empty descrs * @@ -1127,6 +1187,7 @@ spider_net_decode_one_descr(struct spider_net_card *card) struct spider_net_descr_chain *chain = &card->rx_chain; struct spider_net_descr *descr = chain->tail; struct spider_net_hw_descr *hwdescr = descr->hwdescr; + u32 hw_buf_addr; int status; status = spider_net_get_descr_status(hwdescr); @@ -1140,15 +1201,17 @@ spider_net_decode_one_descr(struct spider_net_card *card) chain->tail = descr->next; /* unmap descriptor */ - pci_unmap_single(card->pdev, hwdescr->buf_addr, + hw_buf_addr = hwdescr->buf_addr; + hwdescr->buf_addr = 0xffffffff; + pci_unmap_single(card->pdev, hw_buf_addr, SPIDER_NET_MAX_FRAME, PCI_DMA_FROMDEVICE); if ( (status == SPIDER_NET_DESCR_RESPONSE_ERROR) || (status == SPIDER_NET_DESCR_PROTECTION_ERROR) || (status == SPIDER_NET_DESCR_FORCE_END) ) { if (netif_msg_rx_err(card)) - pr_err("%s: dropping RX descriptor with state %d\n", - card->netdev->name, status); + dev_err(&card->netdev->dev, + "dropping RX descriptor with state %d\n", status); card->netdev_stats.rx_dropped++; goto bad_desc; } @@ -1156,8 +1219,8 @@ spider_net_decode_one_descr(struct spider_net_card *card) if ( (status != SPIDER_NET_DESCR_COMPLETE) && (status != SPIDER_NET_DESCR_FRAME_END) ) { if (netif_msg_rx_err(card)) - pr_err("%s: RX descriptor with unknown state %d\n", - card->netdev->name, status); + dev_err(&card->netdev->dev, + "RX descriptor with unknown state %d\n", status); card->spider_stats.rx_desc_unk_state++; goto bad_desc; } @@ -1165,18 +1228,17 @@ spider_net_decode_one_descr(struct spider_net_card *card) /* The cases we'll throw away the packet immediately */ if (hwdescr->data_error & SPIDER_NET_DESTROY_RX_FLAGS) { if (netif_msg_rx_err(card)) - pr_err("%s: error in received descriptor found, " + dev_err(&card->netdev->dev, + "error in received descriptor found, " "data_status=x%08x, data_error=x%08x\n", - card->netdev->name, hwdescr->data_status, hwdescr->data_error); goto bad_desc; } - if (hwdescr->dmac_cmd_status & 0xfcf4) { - pr_err("%s: bad status, cmd_status=x%08x\n", - card->netdev->name, + if (hwdescr->dmac_cmd_status & SPIDER_NET_DESCR_BAD_STATUS) { + dev_err(&card->netdev->dev, "bad status, cmd_status=x%08x\n", hwdescr->dmac_cmd_status); - pr_err("buf_addr=x%08x\n", hwdescr->buf_addr); + pr_err("buf_addr=x%08x\n", hw_buf_addr); pr_err("buf_size=x%08x\n", hwdescr->buf_size); pr_err("next_descr_addr=x%08x\n", hwdescr->next_descr_addr); pr_err("result_size=x%08x\n", hwdescr->result_size); @@ -1196,6 +1258,8 @@ spider_net_decode_one_descr(struct spider_net_card *card) return 1; bad_desc: + if (netif_msg_rx_err(card)) + show_rx_chain(card); dev_kfree_skb_irq(descr->skb); descr->skb = NULL; hwdescr->dmac_cmd_status = SPIDER_NET_DESCR_NOT_IN_USE; @@ -1221,7 +1285,6 @@ spider_net_poll(struct net_device *netdev, int *budget) int packets_to_do, packets_done = 0; int no_more_packets = 0; - spider_net_cleanup_tx_ring(card); packets_to_do = min(*budget, netdev->quota); while (packets_to_do) { @@ -1246,6 +1309,8 @@ spider_net_poll(struct net_device *netdev, int *budget) spider_net_refill_rx_chain(card); spider_net_enable_rxdmac(card); + spider_net_cleanup_tx_ring(card); + /* if all packets are in the stack, enable interrupts and return 0 */ /* if not, return 1 */ if (no_more_packets) { @@ -1415,7 +1480,7 @@ spider_net_handle_error_irq(struct spider_net_card *card, u32 status_reg) case SPIDER_NET_GPWFFINT: /* PHY command queue full */ if (netif_msg_intr(card)) - pr_err("PHY write queue full\n"); + dev_err(&card->netdev->dev, "PHY write queue full\n"); show_error = 0; break; @@ -1582,9 +1647,8 @@ spider_net_handle_error_irq(struct spider_net_card *card, u32 status_reg) } if ((show_error) && (netif_msg_intr(card)) && net_ratelimit()) - pr_err("Got error interrupt on %s, GHIINT0STS = 0x%08x, " + dev_err(&card->netdev->dev, "Error interrupt, GHIINT0STS = 0x%08x, " "GHIINT1STS = 0x%08x, GHIINT2STS = 0x%08x\n", - card->netdev->name, status_reg, error_reg1, error_reg2); /* clear interrupt sources */ @@ -1849,7 +1913,8 @@ spider_net_init_firmware(struct spider_net_card *card) SPIDER_NET_FIRMWARE_NAME, &card->pdev->dev) == 0) { if ( (firmware->size != SPIDER_NET_FIRMWARE_LEN) && netif_msg_probe(card) ) { - pr_err("Incorrect size of spidernet firmware in " \ + dev_err(&card->netdev->dev, + "Incorrect size of spidernet firmware in " \ "filesystem. Looking in host firmware...\n"); goto try_host_fw; } @@ -1873,8 +1938,8 @@ try_host_fw: if ( (fw_size != SPIDER_NET_FIRMWARE_LEN) && netif_msg_probe(card) ) { - pr_err("Incorrect size of spidernet firmware in " \ - "host firmware\n"); + dev_err(&card->netdev->dev, + "Incorrect size of spidernet firmware in host firmware\n"); goto done; } @@ -1884,7 +1949,8 @@ done: return err; out_err: if (netif_msg_probe(card)) - pr_err("Couldn't find spidernet firmware in filesystem " \ + dev_err(&card->netdev->dev, + "Couldn't find spidernet firmware in filesystem " \ "or host firmware\n"); return err; } @@ -2279,13 +2345,14 @@ spider_net_setup_netdev(struct spider_net_card *card) result = spider_net_set_mac(netdev, &addr); if ((result) && (netif_msg_probe(card))) - pr_err("Failed to set MAC address: %i\n", result); + dev_err(&card->netdev->dev, + "Failed to set MAC address: %i\n", result); result = register_netdev(netdev); if (result) { if (netif_msg_probe(card)) - pr_err("Couldn't register net_device: %i\n", - result); + dev_err(&card->netdev->dev, + "Couldn't register net_device: %i\n", result); return result; } @@ -2363,17 +2430,19 @@ spider_net_setup_pci_dev(struct pci_dev *pdev) unsigned long mmio_start, mmio_len; if (pci_enable_device(pdev)) { - pr_err("Couldn't enable PCI device\n"); + dev_err(&pdev->dev, "Couldn't enable PCI device\n"); return NULL; } if (!(pci_resource_flags(pdev, 0) & IORESOURCE_MEM)) { - pr_err("Couldn't find proper PCI device base address.\n"); + dev_err(&pdev->dev, + "Couldn't find proper PCI device base address.\n"); goto out_disable_dev; } if (pci_request_regions(pdev, spider_net_driver_name)) { - pr_err("Couldn't obtain PCI resources, aborting.\n"); + dev_err(&pdev->dev, + "Couldn't obtain PCI resources, aborting.\n"); goto out_disable_dev; } @@ -2381,8 +2450,8 @@ spider_net_setup_pci_dev(struct pci_dev *pdev) card = spider_net_alloc_card(); if (!card) { - pr_err("Couldn't allocate net_device structure, " - "aborting.\n"); + dev_err(&pdev->dev, + "Couldn't allocate net_device structure, aborting.\n"); goto out_release_regions; } card->pdev = pdev; @@ -2396,7 +2465,8 @@ spider_net_setup_pci_dev(struct pci_dev *pdev) card->regs = ioremap(mmio_start, mmio_len); if (!card->regs) { - pr_err("Couldn't obtain PCI resources, aborting.\n"); + dev_err(&pdev->dev, + "Couldn't obtain PCI resources, aborting.\n"); goto out_release_regions; } diff --git a/drivers/net/spider_net.h b/drivers/net/spider_net.h index 1d054aa7150..dbbdb8cee3c 100644 --- a/drivers/net/spider_net.h +++ b/drivers/net/spider_net.h @@ -349,11 +349,23 @@ enum spider_net_int2_status { #define SPIDER_NET_GPRDAT_MASK 0x0000ffff #define SPIDER_NET_DMAC_NOINTR_COMPLETE 0x00800000 -#define SPIDER_NET_DMAC_NOCS 0x00040000 +#define SPIDER_NET_DMAC_TXFRMTL 0x00040000 #define SPIDER_NET_DMAC_TCP 0x00020000 #define SPIDER_NET_DMAC_UDP 0x00030000 #define SPIDER_NET_TXDCEST 0x08000000 +#define SPIDER_NET_DESCR_RXFDIS 0x00000001 +#define SPIDER_NET_DESCR_RXDCEIS 0x00000002 +#define SPIDER_NET_DESCR_RXDEN0IS 0x00000004 +#define SPIDER_NET_DESCR_RXINVDIS 0x00000008 +#define SPIDER_NET_DESCR_RXRERRIS 0x00000010 +#define SPIDER_NET_DESCR_RXFDCIMS 0x00000100 +#define SPIDER_NET_DESCR_RXDCEIMS 0x00000200 +#define SPIDER_NET_DESCR_RXDEN0IMS 0x00000400 +#define SPIDER_NET_DESCR_RXINVDIMS 0x00000800 +#define SPIDER_NET_DESCR_RXRERRMIS 0x00001000 +#define SPIDER_NET_DESCR_UNUSED 0x077fe0e0 + #define SPIDER_NET_DESCR_IND_PROC_MASK 0xF0000000 #define SPIDER_NET_DESCR_COMPLETE 0x00000000 /* used in rx and tx */ #define SPIDER_NET_DESCR_RESPONSE_ERROR 0x10000000 /* used in rx and tx */ @@ -364,6 +376,13 @@ enum spider_net_int2_status { #define SPIDER_NET_DESCR_NOT_IN_USE 0xF0000000 #define SPIDER_NET_DESCR_TXDESFLG 0x00800000 +#define SPIDER_NET_DESCR_BAD_STATUS (SPIDER_NET_DESCR_RXDEN0IS | \ + SPIDER_NET_DESCR_RXRERRIS | \ + SPIDER_NET_DESCR_RXDEN0IMS | \ + SPIDER_NET_DESCR_RXINVDIMS | \ + SPIDER_NET_DESCR_RXRERRMIS | \ + SPIDER_NET_DESCR_UNUSED) + /* Descriptor, as defined by the hardware */ struct spider_net_hw_descr { u32 buf_addr; diff --git a/drivers/net/tulip/Kconfig b/drivers/net/tulip/Kconfig index 8c9634a98c1..1c537d5a306 100644 --- a/drivers/net/tulip/Kconfig +++ b/drivers/net/tulip/Kconfig @@ -2,17 +2,17 @@ # Tulip family network device configuration # -menu "Tulip family network device support" - depends on NET_ETHERNET && (PCI || EISA || CARDBUS) - -config NET_TULIP +menuconfig NET_TULIP bool "\"Tulip\" family network device support" + depends on PCI || EISA || CARDBUS help This selects the "Tulip" family of EISA/PCI network cards. +if NET_TULIP + config DE2104X tristate "Early DECchip Tulip (dc2104x) PCI support (EXPERIMENTAL)" - depends on NET_TULIP && PCI && EXPERIMENTAL + depends on PCI && EXPERIMENTAL select CRC32 ---help--- This driver is developed for the SMC EtherPower series Ethernet @@ -30,7 +30,7 @@ config DE2104X config TULIP tristate "DECchip Tulip (dc2114x) PCI support" - depends on NET_TULIP && PCI + depends on PCI select CRC32 ---help--- This driver is developed for the SMC EtherPower series Ethernet @@ -95,7 +95,7 @@ config TULIP_NAPI_HW_MITIGATION config DE4X5 tristate "Generic DECchip & DIGITAL EtherWORKS PCI/EISA" - depends on NET_TULIP && (PCI || EISA) + depends on PCI || EISA select CRC32 ---help--- This is support for the DIGITAL series of PCI/EISA Ethernet cards. @@ -112,7 +112,7 @@ config DE4X5 config WINBOND_840 tristate "Winbond W89c840 Ethernet support" - depends on NET_TULIP && PCI + depends on PCI select CRC32 select MII help @@ -123,7 +123,7 @@ config WINBOND_840 config DM9102 tristate "Davicom DM910x/DM980x support" - depends on NET_TULIP && PCI + depends on PCI select CRC32 ---help--- This driver is for DM9102(A)/DM9132/DM9801 compatible PCI cards from @@ -137,7 +137,7 @@ config DM9102 config ULI526X tristate "ULi M526x controller support" - depends on NET_TULIP && PCI + depends on PCI select CRC32 ---help--- This driver is for ULi M5261/M5263 10/100M Ethernet Controller @@ -149,7 +149,7 @@ config ULI526X config PCMCIA_XIRCOM tristate "Xircom CardBus support (new driver)" - depends on NET_TULIP && CARDBUS + depends on CARDBUS ---help--- This driver is for the Digital "Tulip" Ethernet CardBus adapters. It should work with most DEC 21*4*-based chips/ethercards, as well @@ -162,7 +162,7 @@ config PCMCIA_XIRCOM config PCMCIA_XIRTULIP tristate "Xircom Tulip-like CardBus support (old driver)" - depends on NET_TULIP && CARDBUS && BROKEN_ON_SMP + depends on CARDBUS && BROKEN_ON_SMP select CRC32 ---help--- This driver is for the Digital "Tulip" Ethernet CardBus adapters. @@ -174,5 +174,4 @@ config PCMCIA_XIRTULIP <file:Documentation/networking/net-modules.txt>. The module will be called xircom_tulip_cb. If unsure, say N. -endmenu - +endif # NET_TULIP diff --git a/drivers/net/tulip/de2104x.c b/drivers/net/tulip/de2104x.c index 861729806dc..d380e0b3f05 100644 --- a/drivers/net/tulip/de2104x.c +++ b/drivers/net/tulip/de2104x.c @@ -785,7 +785,6 @@ static void __de_set_rx_mode (struct net_device *dev) de->tx_head = NEXT_TX(entry); - BUG_ON(TX_BUFFS_AVAIL(de) < 0); if (TX_BUFFS_AVAIL(de) == 0) netif_stop_queue(dev); diff --git a/drivers/net/tulip/de4x5.c b/drivers/net/tulip/de4x5.c index 62143f92c23..42fca26afc5 100644 --- a/drivers/net/tulip/de4x5.c +++ b/drivers/net/tulip/de4x5.c @@ -597,7 +597,7 @@ static char *args; #endif struct parameters { - int fdx; + bool fdx; int autosense; }; @@ -809,10 +809,10 @@ struct de4x5_private { s32 irq_en; /* Summary interrupt bits */ int media; /* Media (eg TP), mode (eg 100B)*/ int c_media; /* Remember the last media conn */ - int fdx; /* media full duplex flag */ + bool fdx; /* media full duplex flag */ int linkOK; /* Link is OK */ int autosense; /* Allow/disallow autosensing */ - int tx_enable; /* Enable descriptor polling */ + bool tx_enable; /* Enable descriptor polling */ int setup_f; /* Setup frame filtering type */ int local_state; /* State within a 'media' state */ struct mii_phy phy[DE4X5_MAX_PHY]; /* List of attached PHY devices */ @@ -838,8 +838,8 @@ struct de4x5_private { struct de4x5_srom srom; /* A copy of the SROM */ int cfrv; /* Card CFRV copy */ int rx_ovf; /* Check for 'RX overflow' tag */ - int useSROM; /* For non-DEC card use SROM */ - int useMII; /* Infoblock using the MII */ + bool useSROM; /* For non-DEC card use SROM */ + bool useMII; /* Infoblock using the MII */ int asBitValid; /* Autosense bits in GEP? */ int asPolarity; /* 0 => asserted high */ int asBit; /* Autosense bit number in GEP */ @@ -928,7 +928,7 @@ static int dc21040_state(struct net_device *dev, int csr13, int csr14, int c static int test_media(struct net_device *dev, s32 irqs, s32 irq_mask, s32 csr13, s32 csr14, s32 csr15, s32 msec); static int test_for_100Mb(struct net_device *dev, int msec); static int wait_for_link(struct net_device *dev); -static int test_mii_reg(struct net_device *dev, int reg, int mask, int pol, long msec); +static int test_mii_reg(struct net_device *dev, int reg, int mask, bool pol, long msec); static int is_spd_100(struct net_device *dev); static int is_100_up(struct net_device *dev); static int is_10_up(struct net_device *dev); @@ -1109,7 +1109,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct device *gendev) /* ** Now find out what kind of DC21040/DC21041/DC21140 board we have. */ - lp->useSROM = FALSE; + lp->useSROM = false; if (lp->bus == PCI) { PCI_signature(name, lp); } else { @@ -1137,7 +1137,7 @@ de4x5_hw_init(struct net_device *dev, u_long iobase, struct device *gendev) lp->cache.gepc = GEP_INIT; lp->asBit = GEP_SLNK; lp->asPolarity = GEP_SLNK; - lp->asBitValid = TRUE; + lp->asBitValid = ~0; lp->timeout = -1; lp->gendev = gendev; spin_lock_init(&lp->lock); @@ -1463,7 +1463,7 @@ de4x5_queue_pkt(struct sk_buff *skb, struct net_device *dev) u_long flags = 0; netif_stop_queue(dev); - if (lp->tx_enable == NO) { /* Cannot send for now */ + if (!lp->tx_enable) { /* Cannot send for now */ return -1; } @@ -2424,7 +2424,7 @@ dc21040_autoconf(struct net_device *dev) switch (lp->media) { case INIT: DISABLE_IRQs; - lp->tx_enable = NO; + lp->tx_enable = false; lp->timeout = -1; de4x5_save_skbs(dev); if ((lp->autosense == AUTO) || (lp->autosense == TP)) { @@ -2477,7 +2477,7 @@ dc21040_autoconf(struct net_device *dev) lp->c_media = lp->media; } lp->media = INIT; - lp->tx_enable = NO; + lp->tx_enable = false; break; } @@ -2578,7 +2578,7 @@ dc21041_autoconf(struct net_device *dev) switch (lp->media) { case INIT: DISABLE_IRQs; - lp->tx_enable = NO; + lp->tx_enable = false; lp->timeout = -1; de4x5_save_skbs(dev); /* Save non transmitted skb's */ if ((lp->autosense == AUTO) || (lp->autosense == TP_NW)) { @@ -2757,7 +2757,7 @@ dc21041_autoconf(struct net_device *dev) lp->c_media = lp->media; } lp->media = INIT; - lp->tx_enable = NO; + lp->tx_enable = false; break; } @@ -2781,7 +2781,7 @@ dc21140m_autoconf(struct net_device *dev) case INIT: if (lp->timeout < 0) { DISABLE_IRQs; - lp->tx_enable = FALSE; + lp->tx_enable = false; lp->linkOK = 0; de4x5_save_skbs(dev); /* Save non transmitted skb's */ } @@ -2830,7 +2830,7 @@ dc21140m_autoconf(struct net_device *dev) if (lp->timeout < 0) { mii_wr(MII_CR_ASSE | MII_CR_RAN, MII_CR, lp->phy[lp->active].addr, DE4X5_MII); } - cr = test_mii_reg(dev, MII_CR, MII_CR_RAN, FALSE, 500); + cr = test_mii_reg(dev, MII_CR, MII_CR_RAN, false, 500); if (cr < 0) { next_tick = cr & ~TIMER_CB; } else { @@ -2845,7 +2845,7 @@ dc21140m_autoconf(struct net_device *dev) break; case 1: - if ((sr=test_mii_reg(dev, MII_SR, MII_SR_ASSC, TRUE, 2000)) < 0) { + if ((sr=test_mii_reg(dev, MII_SR, MII_SR_ASSC, true, 2000)) < 0) { next_tick = sr & ~TIMER_CB; } else { lp->media = SPD_DET; @@ -2857,10 +2857,10 @@ dc21140m_autoconf(struct net_device *dev) if (!(anlpa & MII_ANLPA_RF) && (cap = anlpa & MII_ANLPA_TAF & ana)) { if (cap & MII_ANA_100M) { - lp->fdx = ((ana & anlpa & MII_ANA_FDAM & MII_ANA_100M) ? TRUE : FALSE); + lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_100M) != 0; lp->media = _100Mb; } else if (cap & MII_ANA_10M) { - lp->fdx = ((ana & anlpa & MII_ANA_FDAM & MII_ANA_10M) ? TRUE : FALSE); + lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_10M) != 0; lp->media = _10Mb; } @@ -2932,7 +2932,7 @@ dc21140m_autoconf(struct net_device *dev) lp->c_media = lp->media; } lp->media = INIT; - lp->tx_enable = FALSE; + lp->tx_enable = false; break; } @@ -2965,7 +2965,7 @@ dc2114x_autoconf(struct net_device *dev) case INIT: if (lp->timeout < 0) { DISABLE_IRQs; - lp->tx_enable = FALSE; + lp->tx_enable = false; lp->linkOK = 0; lp->timeout = -1; de4x5_save_skbs(dev); /* Save non transmitted skb's */ @@ -3013,7 +3013,7 @@ dc2114x_autoconf(struct net_device *dev) if (lp->timeout < 0) { mii_wr(MII_CR_ASSE | MII_CR_RAN, MII_CR, lp->phy[lp->active].addr, DE4X5_MII); } - cr = test_mii_reg(dev, MII_CR, MII_CR_RAN, FALSE, 500); + cr = test_mii_reg(dev, MII_CR, MII_CR_RAN, false, 500); if (cr < 0) { next_tick = cr & ~TIMER_CB; } else { @@ -3028,7 +3028,8 @@ dc2114x_autoconf(struct net_device *dev) break; case 1: - if ((sr=test_mii_reg(dev, MII_SR, MII_SR_ASSC, TRUE, 2000)) < 0) { + sr = test_mii_reg(dev, MII_SR, MII_SR_ASSC, true, 2000); + if (sr < 0) { next_tick = sr & ~TIMER_CB; } else { lp->media = SPD_DET; @@ -3040,10 +3041,10 @@ dc2114x_autoconf(struct net_device *dev) if (!(anlpa & MII_ANLPA_RF) && (cap = anlpa & MII_ANLPA_TAF & ana)) { if (cap & MII_ANA_100M) { - lp->fdx = ((ana & anlpa & MII_ANA_FDAM & MII_ANA_100M) ? TRUE : FALSE); + lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_100M) != 0; lp->media = _100Mb; } else if (cap & MII_ANA_10M) { - lp->fdx = ((ana & anlpa & MII_ANA_FDAM & MII_ANA_10M) ? TRUE : FALSE); + lp->fdx = (ana & anlpa & MII_ANA_FDAM & MII_ANA_10M) != 0; lp->media = _10Mb; } } @@ -3222,14 +3223,14 @@ srom_map_media(struct net_device *dev) { struct de4x5_private *lp = netdev_priv(dev); - lp->fdx = 0; + lp->fdx = false; if (lp->infoblock_media == lp->media) return 0; switch(lp->infoblock_media) { case SROM_10BASETF: if (!lp->params.fdx) return -1; - lp->fdx = TRUE; + lp->fdx = true; case SROM_10BASET: if (lp->params.fdx && !lp->fdx) return -1; if ((lp->chipset == DC21140) || ((lp->chipset & ~0x00ff) == DC2114x)) { @@ -3249,7 +3250,7 @@ srom_map_media(struct net_device *dev) case SROM_100BASETF: if (!lp->params.fdx) return -1; - lp->fdx = TRUE; + lp->fdx = true; case SROM_100BASET: if (lp->params.fdx && !lp->fdx) return -1; lp->media = _100Mb; @@ -3261,7 +3262,7 @@ srom_map_media(struct net_device *dev) case SROM_100BASEFF: if (!lp->params.fdx) return -1; - lp->fdx = TRUE; + lp->fdx = true; case SROM_100BASEF: if (lp->params.fdx && !lp->fdx) return -1; lp->media = _100Mb; @@ -3297,7 +3298,7 @@ de4x5_init_connection(struct net_device *dev) spin_lock_irqsave(&lp->lock, flags); de4x5_rst_desc_ring(dev); de4x5_setup_intr(dev); - lp->tx_enable = YES; + lp->tx_enable = true; spin_unlock_irqrestore(&lp->lock, flags); outl(POLL_DEMAND, DE4X5_TPD); @@ -3336,7 +3337,7 @@ de4x5_reset_phy(struct net_device *dev) } } if (lp->useMII) { - next_tick = test_mii_reg(dev, MII_CR, MII_CR_RST, FALSE, 500); + next_tick = test_mii_reg(dev, MII_CR, MII_CR_RST, false, 500); } } else if (lp->chipset == DC21140) { PHY_HARD_RESET; @@ -3466,7 +3467,7 @@ wait_for_link(struct net_device *dev) ** */ static int -test_mii_reg(struct net_device *dev, int reg, int mask, int pol, long msec) +test_mii_reg(struct net_device *dev, int reg, int mask, bool pol, long msec) { struct de4x5_private *lp = netdev_priv(dev); int test; @@ -3476,9 +3477,8 @@ test_mii_reg(struct net_device *dev, int reg, int mask, int pol, long msec) lp->timeout = msec/100; } - if (pol) pol = ~0; reg = mii_rd((u_char)reg, lp->phy[lp->active].addr, DE4X5_MII) & mask; - test = (reg ^ pol) & mask; + test = (reg ^ (pol ? ~0 : 0)) & mask; if (test && --lp->timeout) { reg = 100 | TIMER_CB; @@ -3992,10 +3992,10 @@ PCI_signature(char *name, struct de4x5_private *lp) ))))))); } if (lp->chipset != DC21041) { - lp->useSROM = TRUE; /* card is not recognisably DEC */ + lp->useSROM = true; /* card is not recognisably DEC */ } } else if ((lp->chipset & ~0x00ff) == DC2114x) { - lp->useSROM = TRUE; + lp->useSROM = true; } return status; @@ -4216,7 +4216,7 @@ srom_repair(struct net_device *dev, int card) memset((char *)&lp->srom, 0, sizeof(struct de4x5_srom)); memcpy(lp->srom.ieee_addr, (char *)dev->dev_addr, ETH_ALEN); memcpy(lp->srom.info, (char *)&srom_repair_info[SMC-1], 100); - lp->useSROM = TRUE; + lp->useSROM = true; break; } @@ -4392,7 +4392,7 @@ srom_infoleaf_info(struct net_device *dev) if (lp->chipset == infoleaf_array[i].chipset) break; } if (i == INFOLEAF_SIZE) { - lp->useSROM = FALSE; + lp->useSROM = false; printk("%s: Cannot find correct chipset for SROM decoding!\n", dev->name); return -ENXIO; @@ -4409,7 +4409,7 @@ srom_infoleaf_info(struct net_device *dev) if (lp->device == *p) break; } if (i == 0) { - lp->useSROM = FALSE; + lp->useSROM = false; printk("%s: Cannot find correct PCI device [%d] for SROM decoding!\n", dev->name, lp->device); return -ENXIO; @@ -4542,7 +4542,7 @@ dc21140_infoleaf(struct net_device *dev) } lp->media = INIT; lp->tcount = 0; - lp->tx_enable = FALSE; + lp->tx_enable = false; } return next_tick & ~TIMER_CB; @@ -4577,7 +4577,7 @@ dc21142_infoleaf(struct net_device *dev) } lp->media = INIT; lp->tcount = 0; - lp->tx_enable = FALSE; + lp->tx_enable = false; } return next_tick & ~TIMER_CB; @@ -4611,7 +4611,7 @@ dc21143_infoleaf(struct net_device *dev) } lp->media = INIT; lp->tcount = 0; - lp->tx_enable = FALSE; + lp->tx_enable = false; } return next_tick & ~TIMER_CB; @@ -4650,7 +4650,7 @@ compact_infoblock(struct net_device *dev, u_char count, u_char *p) lp->asBit = 1 << ((csr6 >> 1) & 0x07); lp->asPolarity = ((csr6 & 0x80) ? -1 : 0) & lp->asBit; lp->infoblock_csr6 = OMR_DEF | ((csr6 & 0x71) << 18); - lp->useMII = FALSE; + lp->useMII = false; de4x5_switch_mac_port(dev); } @@ -4691,7 +4691,7 @@ type0_infoblock(struct net_device *dev, u_char count, u_char *p) lp->asBit = 1 << ((csr6 >> 1) & 0x07); lp->asPolarity = ((csr6 & 0x80) ? -1 : 0) & lp->asBit; lp->infoblock_csr6 = OMR_DEF | ((csr6 & 0x71) << 18); - lp->useMII = FALSE; + lp->useMII = false; de4x5_switch_mac_port(dev); } @@ -4731,7 +4731,7 @@ type1_infoblock(struct net_device *dev, u_char count, u_char *p) lp->ibn = 1; lp->active = *p; lp->infoblock_csr6 = OMR_MII_100; - lp->useMII = TRUE; + lp->useMII = true; lp->infoblock_media = ANS; de4x5_switch_mac_port(dev); @@ -4773,7 +4773,7 @@ type2_infoblock(struct net_device *dev, u_char count, u_char *p) lp->cache.gepc = ((s32)(TWIDDLE(p)) << 16); p += 2; lp->cache.gep = ((s32)(TWIDDLE(p)) << 16); lp->infoblock_csr6 = OMR_SIA; - lp->useMII = FALSE; + lp->useMII = false; de4x5_switch_mac_port(dev); } @@ -4814,7 +4814,7 @@ type3_infoblock(struct net_device *dev, u_char count, u_char *p) lp->active = *p; if (MOTO_SROM_BUG) lp->active = 0; lp->infoblock_csr6 = OMR_MII_100; - lp->useMII = TRUE; + lp->useMII = true; lp->infoblock_media = ANS; de4x5_switch_mac_port(dev); @@ -4856,7 +4856,7 @@ type4_infoblock(struct net_device *dev, u_char count, u_char *p) lp->asBit = 1 << ((csr6 >> 1) & 0x07); lp->asPolarity = ((csr6 & 0x80) ? -1 : 0) & lp->asBit; lp->infoblock_csr6 = OMR_DEF | ((csr6 & 0x71) << 18); - lp->useMII = FALSE; + lp->useMII = false; de4x5_switch_mac_port(dev); } @@ -5077,7 +5077,7 @@ mii_get_phy(struct net_device *dev) int id; lp->active = 0; - lp->useMII = TRUE; + lp->useMII = true; /* Search the MII address space for possible PHY devices */ for (n=0, lp->mii_cnt=0, i=1; !((i==1) && (n==1)); i=(i+1)%DE4X5_MAX_MII) { @@ -5127,7 +5127,7 @@ mii_get_phy(struct net_device *dev) de4x5_dbg_mii(dev, k); } } - if (!lp->mii_cnt) lp->useMII = FALSE; + if (!lp->mii_cnt) lp->useMII = false; return lp->mii_cnt; } diff --git a/drivers/net/tulip/de4x5.h b/drivers/net/tulip/de4x5.h index 57226e5eb8a..12af0cc037f 100644 --- a/drivers/net/tulip/de4x5.h +++ b/drivers/net/tulip/de4x5.h @@ -893,15 +893,6 @@ #define PHYS_ADDR_ONLY 1 /* Update the physical address only */ /* -** Booleans -*/ -#define NO 0 -#define FALSE 0 - -#define YES ~0 -#define TRUE ~0 - -/* ** Adapter state */ #define INITIALISED 0 /* After h/w initialised and mem alloc'd */ diff --git a/drivers/net/usb/usbnet.c b/drivers/net/usb/usbnet.c index a12f576391c..86b69084336 100644 --- a/drivers/net/usb/usbnet.c +++ b/drivers/net/usb/usbnet.c @@ -192,7 +192,7 @@ static int init_status (struct usbnet *dev, struct usb_interface *intf) usb_pipeendpoint(pipe), maxp, period); } } - return 0; + return 0; } /* Passes this packet up the stack, updating its accounting. @@ -326,7 +326,7 @@ static void rx_submit (struct usbnet *dev, struct urb *urb, gfp_t flags) if (netif_running (dev->net) && netif_device_present (dev->net) && !test_bit (EVENT_RX_HALT, &dev->flags)) { - switch (retval = usb_submit_urb (urb, GFP_ATOMIC)){ + switch (retval = usb_submit_urb (urb, GFP_ATOMIC)) { case -EPIPE: usbnet_defer_kevent (dev, EVENT_RX_HALT); break; @@ -393,8 +393,8 @@ static void rx_complete (struct urb *urb) entry->urb = NULL; switch (urb_status) { - // success - case 0: + /* success */ + case 0: if (skb->len < dev->net->hard_header_len) { entry->state = rx_cleanup; dev->stats.rx_errors++; @@ -404,28 +404,30 @@ static void rx_complete (struct urb *urb) } break; - // stalls need manual reset. this is rare ... except that - // when going through USB 2.0 TTs, unplug appears this way. - // we avoid the highspeed version of the ETIMEOUT/EILSEQ - // storm, recovering as needed. - case -EPIPE: + /* stalls need manual reset. this is rare ... except that + * when going through USB 2.0 TTs, unplug appears this way. + * we avoid the highspeed version of the ETIMEOUT/EILSEQ + * storm, recovering as needed. + */ + case -EPIPE: dev->stats.rx_errors++; usbnet_defer_kevent (dev, EVENT_RX_HALT); // FALLTHROUGH - // software-driven interface shutdown - case -ECONNRESET: // async unlink - case -ESHUTDOWN: // hardware gone + /* software-driven interface shutdown */ + case -ECONNRESET: /* async unlink */ + case -ESHUTDOWN: /* hardware gone */ if (netif_msg_ifdown (dev)) devdbg (dev, "rx shutdown, code %d", urb_status); goto block; - // we get controller i/o faults during khubd disconnect() delays. - // throttle down resubmits, to avoid log floods; just temporarily, - // so we still recover when the fault isn't a khubd delay. - case -EPROTO: - case -ETIME: - case -EILSEQ: + /* we get controller i/o faults during khubd disconnect() delays. + * throttle down resubmits, to avoid log floods; just temporarily, + * so we still recover when the fault isn't a khubd delay. + */ + case -EPROTO: + case -ETIME: + case -EILSEQ: dev->stats.rx_errors++; if (!timer_pending (&dev->delay)) { mod_timer (&dev->delay, jiffies + THROTTLE_JIFFIES); @@ -438,12 +440,12 @@ block: urb = NULL; break; - // data overrun ... flush fifo? - case -EOVERFLOW: + /* data overrun ... flush fifo? */ + case -EOVERFLOW: dev->stats.rx_over_errors++; // FALLTHROUGH - default: + default: entry->state = rx_cleanup; dev->stats.rx_errors++; if (netif_msg_rx_err (dev)) @@ -471,22 +473,22 @@ static void intr_complete (struct urb *urb) int status = urb->status; switch (status) { - /* success */ - case 0: + /* success */ + case 0: dev->driver_info->status(dev, urb); break; - /* software-driven interface shutdown */ - case -ENOENT: // urb killed - case -ESHUTDOWN: // hardware gone + /* software-driven interface shutdown */ + case -ENOENT: /* urb killed */ + case -ESHUTDOWN: /* hardware gone */ if (netif_msg_ifdown (dev)) devdbg (dev, "intr shutdown, code %d", status); return; - /* NOTE: not throttling like RX/TX, since this endpoint - * already polls infrequently - */ - default: + /* NOTE: not throttling like RX/TX, since this endpoint + * already polls infrequently + */ + default: devdbg (dev, "intr status %d", status); break; } @@ -569,9 +571,9 @@ static int usbnet_stop (struct net_device *net) temp = unlink_urbs (dev, &dev->txq) + unlink_urbs (dev, &dev->rxq); // maybe wait for deletions to finish. - while (!skb_queue_empty(&dev->rxq) && - !skb_queue_empty(&dev->txq) && - !skb_queue_empty(&dev->done)) { + while (!skb_queue_empty(&dev->rxq) + && !skb_queue_empty(&dev->txq) + && !skb_queue_empty(&dev->done)) { msleep(UNLINK_TIMEOUT_MS); if (netif_msg_ifdown (dev)) devdbg (dev, "waited for %d urb completions", temp); @@ -1011,16 +1013,16 @@ static void usbnet_bh (unsigned long param) while ((skb = skb_dequeue (&dev->done))) { entry = (struct skb_data *) skb->cb; switch (entry->state) { - case rx_done: + case rx_done: entry->state = rx_cleanup; rx_process (dev, skb); continue; - case tx_done: - case rx_cleanup: + case tx_done: + case rx_cleanup: usb_free_urb (entry->urb); dev_kfree_skb (skb); continue; - default: + default: devdbg (dev, "bogus skb state %d", entry->state); } } diff --git a/drivers/net/usb/usbnet.h b/drivers/net/usb/usbnet.h index a3f8b9e7bc0..a6c5820767d 100644 --- a/drivers/net/usb/usbnet.h +++ b/drivers/net/usb/usbnet.h @@ -47,7 +47,7 @@ struct usbnet { unsigned long data [5]; u32 xid; u32 hard_mtu; /* count any extra framing */ - size_t rx_urb_size; /* size for rx urbs */ + size_t rx_urb_size; /* size for rx urbs */ struct mii_if_info mii; /* various kinds of pending driver work */ @@ -85,7 +85,7 @@ struct driver_info { #define FLAG_NO_SETINT 0x0010 /* device can't set_interface() */ #define FLAG_ETHER 0x0020 /* maybe use "eth%d" names */ -#define FLAG_FRAMING_AX 0x0040 /* AX88772/178 packets */ +#define FLAG_FRAMING_AX 0x0040 /* AX88772/178 packets */ /* init device ... can sleep, or cause probe() failure */ int (*bind)(struct usbnet *, struct usb_interface *); @@ -146,9 +146,9 @@ extern void usbnet_cdc_unbind (struct usbnet *, struct usb_interface *); /* CDC and RNDIS support the same host-chosen packet filters for IN transfers */ #define DEFAULT_FILTER (USB_CDC_PACKET_TYPE_BROADCAST \ - |USB_CDC_PACKET_TYPE_ALL_MULTICAST \ - |USB_CDC_PACKET_TYPE_PROMISCUOUS \ - |USB_CDC_PACKET_TYPE_DIRECTED) + |USB_CDC_PACKET_TYPE_ALL_MULTICAST \ + |USB_CDC_PACKET_TYPE_PROMISCUOUS \ + |USB_CDC_PACKET_TYPE_DIRECTED) /* we record the state for each of our queued skbs */ diff --git a/drivers/net/wireless/Kconfig b/drivers/net/wireless/Kconfig index fa2399cbd5c..ae27af0141c 100644 --- a/drivers/net/wireless/Kconfig +++ b/drivers/net/wireless/Kconfig @@ -546,6 +546,18 @@ config USB_ZD1201 To compile this driver as a module, choose M here: the module will be called zd1201. +config RTL8187 + tristate "Realtek 8187 USB support" + depends on MAC80211 && USB && WLAN_80211 && EXPERIMENTAL + select EEPROM_93CX6 + ---help--- + This is a driver for RTL8187 based cards. + These are USB based chips found in cards such as: + + Netgear WG111v2 + + Thanks to Realtek for their support! + source "drivers/net/wireless/hostap/Kconfig" source "drivers/net/wireless/bcm43xx/Kconfig" source "drivers/net/wireless/zd1211rw/Kconfig" diff --git a/drivers/net/wireless/Makefile b/drivers/net/wireless/Makefile index d2124602263..ef35bc6c4a2 100644 --- a/drivers/net/wireless/Makefile +++ b/drivers/net/wireless/Makefile @@ -44,3 +44,6 @@ obj-$(CONFIG_PCMCIA_WL3501) += wl3501_cs.o obj-$(CONFIG_USB_ZD1201) += zd1201.o obj-$(CONFIG_LIBERTAS_USB) += libertas/ + +rtl8187-objs := rtl8187_dev.o rtl8187_rtl8225.o +obj-$(CONFIG_RTL8187) += rtl8187.o diff --git a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c index b37f1e34870..d779199c30d 100644 --- a/drivers/net/wireless/bcm43xx/bcm43xx_phy.c +++ b/drivers/net/wireless/bcm43xx/bcm43xx_phy.c @@ -1638,7 +1638,7 @@ void bcm43xx_phy_set_baseband_attenuation(struct bcm43xx_private *bcm, return; } - if (phy->analog > 1) { + if (phy->analog == 1) { value = bcm43xx_phy_read(bcm, 0x0060) & ~0x003C; value |= (baseband_attenuation << 2) & 0x003C; } else { diff --git a/drivers/net/wireless/hostap/hostap_ap.c b/drivers/net/wireless/hostap/hostap_ap.c index 5b3abd54d0e..90900525379 100644 --- a/drivers/net/wireless/hostap/hostap_ap.c +++ b/drivers/net/wireless/hostap/hostap_ap.c @@ -326,7 +326,6 @@ static int ap_control_proc_read(char *page, char **start, off_t off, char *p = page; struct ap_data *ap = (struct ap_data *) data; char *policy_txt; - struct list_head *ptr; struct mac_entry *entry; if (off != 0) { @@ -352,14 +351,12 @@ static int ap_control_proc_read(char *page, char **start, off_t off, p += sprintf(p, "MAC entries: %u\n", ap->mac_restrictions.entries); p += sprintf(p, "MAC list:\n"); spin_lock_bh(&ap->mac_restrictions.lock); - for (ptr = ap->mac_restrictions.mac_list.next; - ptr != &ap->mac_restrictions.mac_list; ptr = ptr->next) { + list_for_each_entry(entry, &ap->mac_restrictions.mac_list, list) { if (p - page > PAGE_SIZE - 80) { p += sprintf(p, "All entries did not fit one page.\n"); break; } - entry = list_entry(ptr, struct mac_entry, list); p += sprintf(p, MACSTR "\n", MAC2STR(entry->addr)); } spin_unlock_bh(&ap->mac_restrictions.lock); @@ -413,7 +410,6 @@ int ap_control_del_mac(struct mac_restrictions *mac_restrictions, u8 *mac) static int ap_control_mac_deny(struct mac_restrictions *mac_restrictions, u8 *mac) { - struct list_head *ptr; struct mac_entry *entry; int found = 0; @@ -421,10 +417,7 @@ static int ap_control_mac_deny(struct mac_restrictions *mac_restrictions, return 0; spin_lock_bh(&mac_restrictions->lock); - for (ptr = mac_restrictions->mac_list.next; - ptr != &mac_restrictions->mac_list; ptr = ptr->next) { - entry = list_entry(ptr, struct mac_entry, list); - + list_for_each_entry(entry, &mac_restrictions->mac_list, list) { if (memcmp(entry->addr, mac, ETH_ALEN) == 0) { found = 1; break; @@ -519,7 +512,7 @@ static int prism2_ap_proc_read(char *page, char **start, off_t off, { char *p = page; struct ap_data *ap = (struct ap_data *) data; - struct list_head *ptr; + struct sta_info *sta; int i; if (off > PROC_LIMIT) { @@ -529,9 +522,7 @@ static int prism2_ap_proc_read(char *page, char **start, off_t off, p += sprintf(p, "# BSSID CHAN SIGNAL NOISE RATE SSID FLAGS\n"); spin_lock_bh(&ap->sta_table_lock); - for (ptr = ap->sta_list.next; ptr != &ap->sta_list; ptr = ptr->next) { - struct sta_info *sta = (struct sta_info *) ptr; - + list_for_each_entry(sta, &ap->sta_list, list) { if (!sta->ap) continue; @@ -861,7 +852,7 @@ void hostap_init_ap_proc(local_info_t *local) void hostap_free_data(struct ap_data *ap) { - struct list_head *n, *ptr; + struct sta_info *n, *sta; if (ap == NULL || !ap->initialized) { printk(KERN_DEBUG "hostap_free_data: ap has not yet been " @@ -875,8 +866,7 @@ void hostap_free_data(struct ap_data *ap) ap->crypt = ap->crypt_priv = NULL; #endif /* PRISM2_NO_KERNEL_IEEE80211_MGMT */ - list_for_each_safe(ptr, n, &ap->sta_list) { - struct sta_info *sta = list_entry(ptr, struct sta_info, list); + list_for_each_entry_safe(sta, n, &ap->sta_list, list) { ap_sta_hash_del(ap, sta); list_del(&sta->list); if ((sta->flags & WLAN_STA_ASSOC) && !sta->ap && sta->local) @@ -2704,6 +2694,8 @@ ap_tx_ret hostap_handle_sta_tx(local_info_t *local, struct hostap_tx_data *tx) if (hdr->addr1[0] & 0x01) { /* broadcast/multicast frame - no AP related processing */ + if (local->ap->num_sta <= 0) + ret = AP_TX_DROP; goto out; } @@ -3198,15 +3190,14 @@ int hostap_update_rx_stats(struct ap_data *ap, void hostap_update_rates(local_info_t *local) { - struct list_head *ptr; + struct sta_info *sta; struct ap_data *ap = local->ap; if (!ap) return; spin_lock_bh(&ap->sta_table_lock); - for (ptr = ap->sta_list.next; ptr != &ap->sta_list; ptr = ptr->next) { - struct sta_info *sta = (struct sta_info *) ptr; + list_for_each_entry(sta, &ap->sta_list, list) { prism2_check_tx_rates(sta); } spin_unlock_bh(&ap->sta_table_lock); @@ -3242,11 +3233,10 @@ void * ap_crypt_get_ptrs(struct ap_data *ap, u8 *addr, int permanent, void hostap_add_wds_links(local_info_t *local) { struct ap_data *ap = local->ap; - struct list_head *ptr; + struct sta_info *sta; spin_lock_bh(&ap->sta_table_lock); - list_for_each(ptr, &ap->sta_list) { - struct sta_info *sta = list_entry(ptr, struct sta_info, list); + list_for_each_entry(sta, &ap->sta_list, list) { if (sta->ap) hostap_wds_link_oper(local, sta->addr, WDS_ADD); } diff --git a/drivers/net/wireless/hostap/hostap_config.h b/drivers/net/wireless/hostap/hostap_config.h index c090a5aebb5..30acd39d76a 100644 --- a/drivers/net/wireless/hostap/hostap_config.h +++ b/drivers/net/wireless/hostap/hostap_config.h @@ -1,8 +1,6 @@ #ifndef HOSTAP_CONFIG_H #define HOSTAP_CONFIG_H -#define PRISM2_VERSION "0.4.4-kernel" - /* In the previous versions of Host AP driver, support for user space version * of IEEE 802.11 management (hostapd) used to be disabled in the default * configuration. From now on, support for hostapd is always included and it is diff --git a/drivers/net/wireless/hostap/hostap_cs.c b/drivers/net/wireless/hostap/hostap_cs.c index ee1532b62e4..30e723f6597 100644 --- a/drivers/net/wireless/hostap/hostap_cs.c +++ b/drivers/net/wireless/hostap/hostap_cs.c @@ -22,7 +22,6 @@ #include "hostap_wlan.h" -static char *version = PRISM2_VERSION " (Jouni Malinen <j@w1.fi>)"; static dev_info_t dev_info = "hostap_cs"; MODULE_AUTHOR("Jouni Malinen"); @@ -30,7 +29,6 @@ MODULE_DESCRIPTION("Support for Intersil Prism2-based 802.11 wireless LAN " "cards (PC Card)."); MODULE_SUPPORTED_DEVICE("Intersil Prism2-based WLAN cards (PC Card)"); MODULE_LICENSE("GPL"); -MODULE_VERSION(PRISM2_VERSION); static int ignore_cis_vcc; @@ -910,14 +908,12 @@ static struct pcmcia_driver hostap_driver = { static int __init init_prism2_pccard(void) { - printk(KERN_INFO "%s: %s\n", dev_info, version); return pcmcia_register_driver(&hostap_driver); } static void __exit exit_prism2_pccard(void) { pcmcia_unregister_driver(&hostap_driver); - printk(KERN_INFO "%s: Driver unloaded\n", dev_info); } diff --git a/drivers/net/wireless/hostap/hostap_ioctl.c b/drivers/net/wireless/hostap/hostap_ioctl.c index cdea7f71b9e..8c71077d653 100644 --- a/drivers/net/wireless/hostap/hostap_ioctl.c +++ b/drivers/net/wireless/hostap/hostap_ioctl.c @@ -3893,8 +3893,6 @@ static void prism2_get_drvinfo(struct net_device *dev, local = iface->local; strncpy(info->driver, "hostap", sizeof(info->driver) - 1); - strncpy(info->version, PRISM2_VERSION, - sizeof(info->version) - 1); snprintf(info->fw_version, sizeof(info->fw_version) - 1, "%d.%d.%d", (local->sta_fw_ver >> 16) & 0xff, (local->sta_fw_ver >> 8) & 0xff, diff --git a/drivers/net/wireless/hostap/hostap_main.c b/drivers/net/wireless/hostap/hostap_main.c index 4743426cf6a..446de51bab7 100644 --- a/drivers/net/wireless/hostap/hostap_main.c +++ b/drivers/net/wireless/hostap/hostap_main.c @@ -37,7 +37,6 @@ MODULE_AUTHOR("Jouni Malinen"); MODULE_DESCRIPTION("Host AP common routines"); MODULE_LICENSE("GPL"); -MODULE_VERSION(PRISM2_VERSION); #define TX_TIMEOUT (2 * HZ) diff --git a/drivers/net/wireless/hostap/hostap_pci.c b/drivers/net/wireless/hostap/hostap_pci.c index db4899ed4bb..0cd48d151f5 100644 --- a/drivers/net/wireless/hostap/hostap_pci.c +++ b/drivers/net/wireless/hostap/hostap_pci.c @@ -20,7 +20,6 @@ #include "hostap_wlan.h" -static char *version = PRISM2_VERSION " (Jouni Malinen <j@w1.fi>)"; static char *dev_info = "hostap_pci"; @@ -29,7 +28,6 @@ MODULE_DESCRIPTION("Support for Intersil Prism2.5-based 802.11 wireless LAN " "PCI cards."); MODULE_SUPPORTED_DEVICE("Intersil Prism2.5-based WLAN PCI cards"); MODULE_LICENSE("GPL"); -MODULE_VERSION(PRISM2_VERSION); /* struct local_info::hw_priv */ @@ -462,8 +460,6 @@ static struct pci_driver prism2_pci_drv_id = { static int __init init_prism2_pci(void) { - printk(KERN_INFO "%s: %s\n", dev_info, version); - return pci_register_driver(&prism2_pci_drv_id); } @@ -471,7 +467,6 @@ static int __init init_prism2_pci(void) static void __exit exit_prism2_pci(void) { pci_unregister_driver(&prism2_pci_drv_id); - printk(KERN_INFO "%s: Driver unloaded\n", dev_info); } diff --git a/drivers/net/wireless/hostap/hostap_plx.c b/drivers/net/wireless/hostap/hostap_plx.c index f0fd5ecdb24..0183df757b3 100644 --- a/drivers/net/wireless/hostap/hostap_plx.c +++ b/drivers/net/wireless/hostap/hostap_plx.c @@ -23,7 +23,6 @@ #include "hostap_wlan.h" -static char *version = PRISM2_VERSION " (Jouni Malinen <j@w1.fi>)"; static char *dev_info = "hostap_plx"; @@ -32,7 +31,6 @@ MODULE_DESCRIPTION("Support for Intersil Prism2-based 802.11 wireless LAN " "cards (PLX)."); MODULE_SUPPORTED_DEVICE("Intersil Prism2-based WLAN cards (PLX)"); MODULE_LICENSE("GPL"); -MODULE_VERSION(PRISM2_VERSION); static int ignore_cis; @@ -623,8 +621,6 @@ static struct pci_driver prism2_plx_drv_id = { static int __init init_prism2_plx(void) { - printk(KERN_INFO "%s: %s\n", dev_info, version); - return pci_register_driver(&prism2_plx_drv_id); } @@ -632,7 +628,6 @@ static int __init init_prism2_plx(void) static void __exit exit_prism2_plx(void) { pci_unregister_driver(&prism2_plx_drv_id); - printk(KERN_INFO "%s: Driver unloaded\n", dev_info); } diff --git a/drivers/net/wireless/rtl8187.h b/drivers/net/wireless/rtl8187.h new file mode 100644 index 00000000000..6124e467b15 --- /dev/null +++ b/drivers/net/wireless/rtl8187.h @@ -0,0 +1,145 @@ +/* + * Definitions for RTL8187 hardware + * + * Copyright 2007 Michael Wu <flamingice@sourmilk.net> + * Copyright 2007 Andrea Merello <andreamrl@tiscali.it> + * + * Based on the r8187 driver, which is: + * Copyright 2005 Andrea Merello <andreamrl@tiscali.it>, et al. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef RTL8187_H +#define RTL8187_H + +#include "rtl818x.h" + +#define RTL8187_EEPROM_TXPWR_BASE 0x05 +#define RTL8187_EEPROM_MAC_ADDR 0x07 +#define RTL8187_EEPROM_TXPWR_CHAN_1 0x16 /* 3 channels */ +#define RTL8187_EEPROM_TXPWR_CHAN_6 0x1B /* 2 channels */ +#define RTL8187_EEPROM_TXPWR_CHAN_4 0x3D /* 2 channels */ + +#define RTL8187_REQT_READ 0xC0 +#define RTL8187_REQT_WRITE 0x40 +#define RTL8187_REQ_GET_REG 0x05 +#define RTL8187_REQ_SET_REG 0x05 + +#define RTL8187_MAX_RX 0x9C4 + +struct rtl8187_rx_info { + struct urb *urb; + struct ieee80211_hw *dev; +}; + +struct rtl8187_rx_hdr { + __le16 len; + __le16 rate; + u8 noise; + u8 signal; + u8 agc; + u8 reserved; + __le64 mac_time; +} __attribute__((packed)); + +struct rtl8187_tx_info { + struct ieee80211_tx_control *control; + struct urb *urb; + struct ieee80211_hw *dev; +}; + +struct rtl8187_tx_hdr { + __le32 flags; +#define RTL8187_TX_FLAG_NO_ENCRYPT (1 << 15) +#define RTL8187_TX_FLAG_MORE_FRAG (1 << 17) +#define RTL8187_TX_FLAG_CTS (1 << 18) +#define RTL8187_TX_FLAG_RTS (1 << 23) + __le16 rts_duration; + __le16 len; + __le32 retry; +} __attribute__((packed)); + +struct rtl8187_priv { + /* common between rtl818x drivers */ + struct rtl818x_csr *map; + void (*rf_init)(struct ieee80211_hw *); + int mode; + + /* rtl8187 specific */ + struct ieee80211_channel channels[14]; + struct ieee80211_rate rates[12]; + struct ieee80211_hw_mode modes[2]; + struct usb_device *udev; + u8 *hwaddr; + u16 txpwr_base; + u8 asic_rev; + struct sk_buff_head rx_queue; +}; + +void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data); + +static inline u8 rtl818x_ioread8(struct rtl8187_priv *priv, u8 *addr) +{ + u8 val; + + usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0), + RTL8187_REQ_GET_REG, RTL8187_REQT_READ, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); + + return val; +} + +static inline u16 rtl818x_ioread16(struct rtl8187_priv *priv, __le16 *addr) +{ + __le16 val; + + usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0), + RTL8187_REQ_GET_REG, RTL8187_REQT_READ, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); + + return le16_to_cpu(val); +} + +static inline u32 rtl818x_ioread32(struct rtl8187_priv *priv, __le32 *addr) +{ + __le32 val; + + usb_control_msg(priv->udev, usb_rcvctrlpipe(priv->udev, 0), + RTL8187_REQ_GET_REG, RTL8187_REQT_READ, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); + + return le32_to_cpu(val); +} + +static inline void rtl818x_iowrite8(struct rtl8187_priv *priv, + u8 *addr, u8 val) +{ + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + (unsigned long)addr, 0, &val, sizeof(val), HZ / 2); +} + +static inline void rtl818x_iowrite16(struct rtl8187_priv *priv, + __le16 *addr, u16 val) +{ + __le16 buf = cpu_to_le16(val); + + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + (unsigned long)addr, 0, &buf, sizeof(buf), HZ / 2); +} + +static inline void rtl818x_iowrite32(struct rtl8187_priv *priv, + __le32 *addr, u32 val) +{ + __le32 buf = cpu_to_le32(val); + + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + (unsigned long)addr, 0, &buf, sizeof(buf), HZ / 2); +} + +#endif /* RTL8187_H */ diff --git a/drivers/net/wireless/rtl8187_dev.c b/drivers/net/wireless/rtl8187_dev.c new file mode 100644 index 00000000000..cea85894b7f --- /dev/null +++ b/drivers/net/wireless/rtl8187_dev.c @@ -0,0 +1,731 @@ +/* + * Linux device driver for RTL8187 + * + * Copyright 2007 Michael Wu <flamingice@sourmilk.net> + * Copyright 2007 Andrea Merello <andreamrl@tiscali.it> + * + * Based on the r8187 driver, which is: + * Copyright 2005 Andrea Merello <andreamrl@tiscali.it>, et al. + * + * Magic delays and register offsets below are taken from the original + * r8187 driver sources. Thanks to Realtek for their support! + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/usb.h> +#include <linux/delay.h> +#include <linux/etherdevice.h> +#include <linux/eeprom_93cx6.h> +#include <net/mac80211.h> + +#include "rtl8187.h" +#include "rtl8187_rtl8225.h" + +MODULE_AUTHOR("Michael Wu <flamingice@sourmilk.net>"); +MODULE_AUTHOR("Andrea Merello <andreamrl@tiscali.it>"); +MODULE_DESCRIPTION("RTL8187 USB wireless driver"); +MODULE_LICENSE("GPL"); + +static struct usb_device_id rtl8187_table[] __devinitdata = { + /* Realtek */ + {USB_DEVICE(0x0bda, 0x8187)}, + /* Netgear */ + {USB_DEVICE(0x0846, 0x6100)}, + {USB_DEVICE(0x0846, 0x6a00)}, + {} +}; + +MODULE_DEVICE_TABLE(usb, rtl8187_table); + +void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data) +{ + struct rtl8187_priv *priv = dev->priv; + + data <<= 8; + data |= addr | 0x80; + + rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF); + rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF); + rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF); + rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF); + + msleep(1); +} + +static void rtl8187_tx_cb(struct urb *urb) +{ + struct ieee80211_tx_status status = { {0} }; + struct sk_buff *skb = (struct sk_buff *)urb->context; + struct rtl8187_tx_info *info = (struct rtl8187_tx_info *)skb->cb; + + usb_free_urb(info->urb); + if (info->control) + memcpy(&status.control, info->control, sizeof(status.control)); + kfree(info->control); + skb_pull(skb, sizeof(struct rtl8187_tx_hdr)); + status.flags |= IEEE80211_TX_STATUS_ACK; + ieee80211_tx_status_irqsafe(info->dev, skb, &status); +} + +static int rtl8187_tx(struct ieee80211_hw *dev, struct sk_buff *skb, + struct ieee80211_tx_control *control) +{ + struct rtl8187_priv *priv = dev->priv; + struct rtl8187_tx_hdr *hdr; + struct rtl8187_tx_info *info; + struct urb *urb; + u32 tmp; + + urb = usb_alloc_urb(0, GFP_ATOMIC); + if (!urb) { + kfree_skb(skb); + return 0; + } + + hdr = (struct rtl8187_tx_hdr *)skb_push(skb, sizeof(*hdr)); + tmp = skb->len - sizeof(*hdr); + tmp |= RTL8187_TX_FLAG_NO_ENCRYPT; + tmp |= control->rts_cts_rate << 19; + tmp |= control->tx_rate << 24; + if (ieee80211_get_morefrag((struct ieee80211_hdr *)skb)) + tmp |= RTL8187_TX_FLAG_MORE_FRAG; + if (control->flags & IEEE80211_TXCTL_USE_RTS_CTS) { + tmp |= RTL8187_TX_FLAG_RTS; + hdr->rts_duration = + ieee80211_rts_duration(dev, skb->len, control); + } + if (control->flags & IEEE80211_TXCTL_USE_CTS_PROTECT) + tmp |= RTL8187_TX_FLAG_CTS; + hdr->flags = cpu_to_le32(tmp); + hdr->len = 0; + tmp = control->retry_limit << 8; + hdr->retry = cpu_to_le32(tmp); + + info = (struct rtl8187_tx_info *)skb->cb; + info->control = kmemdup(control, sizeof(*control), GFP_ATOMIC); + info->urb = urb; + info->dev = dev; + usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, 2), + hdr, skb->len, rtl8187_tx_cb, skb); + usb_submit_urb(urb, GFP_ATOMIC); + + return 0; +} + +static void rtl8187_rx_cb(struct urb *urb) +{ + struct sk_buff *skb = (struct sk_buff *)urb->context; + struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb; + struct ieee80211_hw *dev = info->dev; + struct rtl8187_priv *priv = dev->priv; + struct rtl8187_rx_hdr *hdr; + struct ieee80211_rx_status rx_status = { 0 }; + int rate, signal; + + spin_lock(&priv->rx_queue.lock); + if (skb->next) + __skb_unlink(skb, &priv->rx_queue); + else { + spin_unlock(&priv->rx_queue.lock); + return; + } + spin_unlock(&priv->rx_queue.lock); + + if (unlikely(urb->status)) { + usb_free_urb(urb); + dev_kfree_skb_irq(skb); + return; + } + + skb_put(skb, urb->actual_length); + hdr = (struct rtl8187_rx_hdr *)(skb_tail_pointer(skb) - sizeof(*hdr)); + skb_trim(skb, le16_to_cpu(hdr->len) & 0x0FFF); + + signal = hdr->agc >> 1; + rate = (le16_to_cpu(hdr->rate) >> 4) & 0xF; + if (rate > 3) { /* OFDM rate */ + if (signal > 90) + signal = 90; + else if (signal < 25) + signal = 25; + signal = 90 - signal; + } else { /* CCK rate */ + if (signal > 95) + signal = 95; + else if (signal < 30) + signal = 30; + signal = 95 - signal; + } + + rx_status.antenna = (hdr->signal >> 7) & 1; + rx_status.signal = 64 - min(hdr->noise, (u8)64); + rx_status.ssi = signal; + rx_status.rate = rate; + rx_status.freq = dev->conf.freq; + rx_status.channel = dev->conf.channel; + rx_status.phymode = dev->conf.phymode; + rx_status.mactime = le64_to_cpu(hdr->mac_time); + ieee80211_rx_irqsafe(dev, skb, &rx_status); + + skb = dev_alloc_skb(RTL8187_MAX_RX); + if (unlikely(!skb)) { + usb_free_urb(urb); + /* TODO check rx queue length and refill *somewhere* */ + return; + } + + info = (struct rtl8187_rx_info *)skb->cb; + info->urb = urb; + info->dev = dev; + urb->transfer_buffer = skb_tail_pointer(skb); + urb->context = skb; + skb_queue_tail(&priv->rx_queue, skb); + + usb_submit_urb(urb, GFP_ATOMIC); +} + +static int rtl8187_init_urbs(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + struct urb *entry; + struct sk_buff *skb; + struct rtl8187_rx_info *info; + + while (skb_queue_len(&priv->rx_queue) < 8) { + skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL); + if (!skb) + break; + entry = usb_alloc_urb(0, GFP_KERNEL); + if (!entry) { + kfree_skb(skb); + break; + } + usb_fill_bulk_urb(entry, priv->udev, + usb_rcvbulkpipe(priv->udev, 1), + skb_tail_pointer(skb), + RTL8187_MAX_RX, rtl8187_rx_cb, skb); + info = (struct rtl8187_rx_info *)skb->cb; + info->urb = entry; + info->dev = dev; + skb_queue_tail(&priv->rx_queue, skb); + usb_submit_urb(entry, GFP_KERNEL); + } + + return 0; +} + +static int rtl8187_init_hw(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + u8 reg; + int i; + + /* reset */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); + + msleep(200); + rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10); + rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11); + rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00); + msleep(200); + + reg = rtl818x_ioread8(priv, &priv->map->CMD); + reg &= (1 << 1); + reg |= RTL818X_CMD_RESET; + rtl818x_iowrite8(priv, &priv->map->CMD, reg); + + i = 10; + do { + msleep(2); + if (!(rtl818x_ioread8(priv, &priv->map->CMD) & + RTL818X_CMD_RESET)) + break; + } while (--i); + + if (!i) { + printk(KERN_ERR "%s: Reset timeout!\n", wiphy_name(dev->wiphy)); + return -ETIMEDOUT; + } + + /* reload registers from eeprom */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD); + + i = 10; + do { + msleep(4); + if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) & + RTL818X_EEPROM_CMD_CONFIG)) + break; + } while (--i); + + if (!i) { + printk(KERN_ERR "%s: eeprom reset timeout!\n", + wiphy_name(dev->wiphy)); + return -ETIMEDOUT; + } + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_ON); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + /* setup card */ + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); + rtl818x_iowrite8(priv, &priv->map->GPIO, 0); + + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); + rtl818x_iowrite8(priv, &priv->map->GPIO, 1); + rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + for (i = 0; i < ETH_ALEN; i++) + rtl818x_iowrite8(priv, &priv->map->MAC[i], priv->hwaddr[i]); + + rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG1); + reg &= 0x3F; + reg |= 0x80; + rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); + rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); + rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0x81); + + // TODO: set RESP_RATE and BRSR properly + rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0); + rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); + + /* host_usb_init */ + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); + rtl818x_iowrite8(priv, &priv->map->GPIO, 0); + reg = rtl818x_ioread8(priv, (u8 *)0xFE53); + rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7)); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); + rtl818x_iowrite8(priv, &priv->map->GPIO, 0x20); + rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80); + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80); + msleep(100); + + rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008); + rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF); + rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7); + msleep(100); + + priv->rf_init(dev); + + rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); + reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & 0xfffe; + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 0x1); + rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10); + rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80); + rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60); + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg); + + return 0; +} + +static void rtl8187_set_channel(struct ieee80211_hw *dev, int channel) +{ + u32 reg; + struct rtl8187_priv *priv = dev->priv; + + reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); + /* Enable TX loopback on MAC level to avoid TX during channel + * changes, as this has be seen to causes problems and the + * card will stop work until next reset + */ + rtl818x_iowrite32(priv, &priv->map->TX_CONF, + reg | RTL818X_TX_CONF_LOOPBACK_MAC); + msleep(10); + rtl8225_rf_set_channel(dev, channel); + msleep(10); + rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); +} + +static int rtl8187_open(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + u32 reg; + int ret; + + ret = rtl8187_init_hw(dev); + if (ret) + return ret; + + rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); + + rtl8187_init_urbs(dev); + + reg = RTL818X_RX_CONF_ONLYERLPKT | + RTL818X_RX_CONF_RX_AUTORESETPHY | + RTL818X_RX_CONF_BSSID | + RTL818X_RX_CONF_MGMT | + RTL818X_RX_CONF_CTRL | + RTL818X_RX_CONF_DATA | + (7 << 13 /* RX FIFO threshold NONE */) | + (7 << 10 /* MAX RX DMA */) | + RTL818X_RX_CONF_BROADCAST | + RTL818X_RX_CONF_MULTICAST | + RTL818X_RX_CONF_NICMAC; + if (priv->mode == IEEE80211_IF_TYPE_MNTR) + reg |= RTL818X_RX_CONF_MONITOR; + + rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); + + reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); + reg &= ~RTL818X_CW_CONF_PERPACKET_CW_SHIFT; + reg |= RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT; + rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); + + reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); + reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT; + reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT; + reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT; + rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); + + reg = RTL818X_TX_CONF_CW_MIN | + (7 << 21 /* MAX TX DMA */) | + RTL818X_TX_CONF_NO_ICV; + rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); + + reg = rtl818x_ioread8(priv, &priv->map->CMD); + reg |= RTL818X_CMD_TX_ENABLE; + reg |= RTL818X_CMD_RX_ENABLE; + rtl818x_iowrite8(priv, &priv->map->CMD, reg); + + return 0; +} + +static int rtl8187_stop(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + struct rtl8187_rx_info *info; + struct sk_buff *skb; + u32 reg; + + rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); + + reg = rtl818x_ioread8(priv, &priv->map->CMD); + reg &= ~RTL818X_CMD_TX_ENABLE; + reg &= ~RTL818X_CMD_RX_ENABLE; + rtl818x_iowrite8(priv, &priv->map->CMD, reg); + + rtl8225_rf_stop(dev); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG4); + rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + while ((skb = skb_dequeue(&priv->rx_queue))) { + info = (struct rtl8187_rx_info *)skb->cb; + usb_kill_urb(info->urb); + kfree_skb(skb); + } + return 0; +} + +static int rtl8187_add_interface(struct ieee80211_hw *dev, + struct ieee80211_if_init_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + + /* NOTE: using IEEE80211_IF_TYPE_MGMT to indicate no mode selected */ + if (priv->mode != IEEE80211_IF_TYPE_MGMT) + return -1; + + switch (conf->type) { + case IEEE80211_IF_TYPE_STA: + case IEEE80211_IF_TYPE_MNTR: + priv->mode = conf->type; + break; + default: + return -EOPNOTSUPP; + } + + priv->hwaddr = conf->mac_addr; + + return 0; +} + +static void rtl8187_remove_interface(struct ieee80211_hw *dev, + struct ieee80211_if_init_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + priv->mode = IEEE80211_IF_TYPE_MGMT; +} + +static int rtl8187_config(struct ieee80211_hw *dev, struct ieee80211_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + rtl8187_set_channel(dev, conf->channel); + + rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22); + + if (conf->flags & IEEE80211_CONF_SHORT_SLOT_TIME) { + rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9); + rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14); + rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14); + rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0x73); + } else { + rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14); + rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24); + rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24); + rtl818x_iowrite8(priv, &priv->map->CW_VAL, 0xa5); + } + + rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2); + rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100); + rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100); + rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100); + return 0; +} + +static int rtl8187_config_interface(struct ieee80211_hw *dev, int if_id, + struct ieee80211_if_conf *conf) +{ + struct rtl8187_priv *priv = dev->priv; + int i; + + for (i = 0; i < ETH_ALEN; i++) + rtl818x_iowrite8(priv, &priv->map->BSSID[i], conf->bssid[i]); + + if (is_valid_ether_addr(conf->bssid)) + rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_INFRA); + else + rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_NO_LINK); + + return 0; +} + +static const struct ieee80211_ops rtl8187_ops = { + .tx = rtl8187_tx, + .open = rtl8187_open, + .stop = rtl8187_stop, + .add_interface = rtl8187_add_interface, + .remove_interface = rtl8187_remove_interface, + .config = rtl8187_config, + .config_interface = rtl8187_config_interface, +}; + +static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom) +{ + struct ieee80211_hw *dev = eeprom->data; + struct rtl8187_priv *priv = dev->priv; + u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); + + eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE; + eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ; + eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK; + eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS; +} + +static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom) +{ + struct ieee80211_hw *dev = eeprom->data; + struct rtl8187_priv *priv = dev->priv; + u8 reg = RTL818X_EEPROM_CMD_PROGRAM; + + if (eeprom->reg_data_in) + reg |= RTL818X_EEPROM_CMD_WRITE; + if (eeprom->reg_data_out) + reg |= RTL818X_EEPROM_CMD_READ; + if (eeprom->reg_data_clock) + reg |= RTL818X_EEPROM_CMD_CK; + if (eeprom->reg_chip_select) + reg |= RTL818X_EEPROM_CMD_CS; + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg); + udelay(10); +} + +static int __devinit rtl8187_probe(struct usb_interface *intf, + const struct usb_device_id *id) +{ + struct usb_device *udev = interface_to_usbdev(intf); + struct ieee80211_hw *dev; + struct rtl8187_priv *priv; + struct eeprom_93cx6 eeprom; + struct ieee80211_channel *channel; + u16 txpwr, reg; + int err, i; + + dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops); + if (!dev) { + printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n"); + return -ENOMEM; + } + + priv = dev->priv; + + SET_IEEE80211_DEV(dev, &intf->dev); + usb_set_intfdata(intf, dev); + priv->udev = udev; + + usb_get_dev(udev); + + skb_queue_head_init(&priv->rx_queue); + memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels)); + memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates)); + priv->map = (struct rtl818x_csr *)0xFF00; + priv->modes[0].mode = MODE_IEEE80211G; + priv->modes[0].num_rates = ARRAY_SIZE(rtl818x_rates); + priv->modes[0].rates = priv->rates; + priv->modes[0].num_channels = ARRAY_SIZE(rtl818x_channels); + priv->modes[0].channels = priv->channels; + priv->modes[1].mode = MODE_IEEE80211B; + priv->modes[1].num_rates = 4; + priv->modes[1].rates = priv->rates; + priv->modes[1].num_channels = ARRAY_SIZE(rtl818x_channels); + priv->modes[1].channels = priv->channels; + priv->mode = IEEE80211_IF_TYPE_MGMT; + dev->flags = IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING | + IEEE80211_HW_RX_INCLUDES_FCS | + IEEE80211_HW_WEP_INCLUDE_IV | + IEEE80211_HW_DATA_NULLFUNC_ACK; + dev->extra_tx_headroom = sizeof(struct rtl8187_tx_hdr); + dev->queues = 1; + dev->max_rssi = 65; + dev->max_signal = 64; + + for (i = 0; i < 2; i++) + if ((err = ieee80211_register_hwmode(dev, &priv->modes[i]))) + goto err_free_dev; + + eeprom.data = dev; + eeprom.register_read = rtl8187_eeprom_register_read; + eeprom.register_write = rtl8187_eeprom_register_write; + if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6)) + eeprom.width = PCI_EEPROM_WIDTH_93C66; + else + eeprom.width = PCI_EEPROM_WIDTH_93C46; + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + udelay(10); + + eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR, + (__le16 __force *)dev->wiphy->perm_addr, 3); + if (!is_valid_ether_addr(dev->wiphy->perm_addr)) { + printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly " + "generated MAC address\n"); + random_ether_addr(dev->wiphy->perm_addr); + } + + channel = priv->channels; + for (i = 0; i < 3; i++) { + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i, + &txpwr); + (*channel++).val = txpwr & 0xFF; + (*channel++).val = txpwr >> 8; + } + for (i = 0; i < 2; i++) { + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i, + &txpwr); + (*channel++).val = txpwr & 0xFF; + (*channel++).val = txpwr >> 8; + } + for (i = 0; i < 2; i++) { + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6 + i, + &txpwr); + (*channel++).val = txpwr & 0xFF; + (*channel++).val = txpwr >> 8; + } + + eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE, + &priv->txpwr_base); + + reg = rtl818x_ioread16(priv, &priv->map->PGSELECT) & ~1; + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg | 1); + /* 0 means asic B-cut, we should use SW 3 wire + * bit-by-bit banging for radio. 1 means we can use + * USB specific request to write radio registers */ + priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3; + rtl818x_iowrite16(priv, &priv->map->PGSELECT, reg); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl8225_write(dev, 0, 0x1B7); + + if (rtl8225_read(dev, 8) != 0x588 || rtl8225_read(dev, 9) != 0x700) + priv->rf_init = rtl8225_rf_init; + else + priv->rf_init = rtl8225z2_rf_init; + + rtl8225_write(dev, 0, 0x0B7); + + err = ieee80211_register_hw(dev); + if (err) { + printk(KERN_ERR "rtl8187: Cannot register device\n"); + goto err_free_dev; + } + + printk(KERN_INFO "%s: hwaddr " MAC_FMT ", rtl8187 V%d + %s\n", + wiphy_name(dev->wiphy), MAC_ARG(dev->wiphy->perm_addr), + priv->asic_rev, priv->rf_init == rtl8225_rf_init ? + "rtl8225" : "rtl8225z2"); + + return 0; + + err_free_dev: + ieee80211_free_hw(dev); + usb_set_intfdata(intf, NULL); + usb_put_dev(udev); + return err; +} + +static void __devexit rtl8187_disconnect(struct usb_interface *intf) +{ + struct ieee80211_hw *dev = usb_get_intfdata(intf); + struct rtl8187_priv *priv; + + if (!dev) + return; + + ieee80211_unregister_hw(dev); + + priv = dev->priv; + usb_put_dev(interface_to_usbdev(intf)); + ieee80211_free_hw(dev); +} + +static struct usb_driver rtl8187_driver = { + .name = KBUILD_MODNAME, + .id_table = rtl8187_table, + .probe = rtl8187_probe, + .disconnect = rtl8187_disconnect, +}; + +static int __init rtl8187_init(void) +{ + return usb_register(&rtl8187_driver); +} + +static void __exit rtl8187_exit(void) +{ + usb_deregister(&rtl8187_driver); +} + +module_init(rtl8187_init); +module_exit(rtl8187_exit); diff --git a/drivers/net/wireless/rtl8187_rtl8225.c b/drivers/net/wireless/rtl8187_rtl8225.c new file mode 100644 index 00000000000..e25a09f1b06 --- /dev/null +++ b/drivers/net/wireless/rtl8187_rtl8225.c @@ -0,0 +1,745 @@ +/* + * Radio tuning for RTL8225 on RTL8187 + * + * Copyright 2007 Michael Wu <flamingice@sourmilk.net> + * Copyright 2007 Andrea Merello <andreamrl@tiscali.it> + * + * Based on the r8187 driver, which is: + * Copyright 2005 Andrea Merello <andreamrl@tiscali.it>, et al. + * + * Magic delays, register offsets, and phy value tables below are + * taken from the original r8187 driver sources. Thanks to Realtek + * for their support! + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/init.h> +#include <linux/usb.h> +#include <net/mac80211.h> + +#include "rtl8187.h" +#include "rtl8187_rtl8225.h" + +static void rtl8225_write_bitbang(struct ieee80211_hw *dev, u8 addr, u16 data) +{ + struct rtl8187_priv *priv = dev->priv; + u16 reg80, reg84, reg82; + u32 bangdata; + int i; + + bangdata = (data << 4) | (addr & 0xf); + + reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput) & 0xfff3; + reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable); + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x7); + + reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x7); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80); + udelay(10); + + for (i = 15; i >= 0; i--) { + u16 reg = reg80 | (bangdata & (1 << i)) >> i; + + if (i & 1) + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1)); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg | (1 << 1)); + + if (!(i & 1)) + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84); + msleep(2); +} + +static void rtl8225_write_8051(struct ieee80211_hw *dev, u8 addr, u16 data) +{ + struct rtl8187_priv *priv = dev->priv; + u16 reg80, reg82, reg84; + + reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput); + reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable); + reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect); + + reg80 &= ~(0x3 << 2); + reg84 &= ~0xF; + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x0007); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x0007); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(2); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80); + udelay(10); + + usb_control_msg(priv->udev, usb_sndctrlpipe(priv->udev, 0), + RTL8187_REQ_SET_REG, RTL8187_REQT_WRITE, + addr, 0x8225, &data, sizeof(data), HZ / 2); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(10); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84); + msleep(2); +} + +void rtl8225_write(struct ieee80211_hw *dev, u8 addr, u16 data) +{ + struct rtl8187_priv *priv = dev->priv; + + if (priv->asic_rev) + rtl8225_write_8051(dev, addr, data); + else + rtl8225_write_bitbang(dev, addr, data); +} + +u16 rtl8225_read(struct ieee80211_hw *dev, u8 addr) +{ + struct rtl8187_priv *priv = dev->priv; + u16 reg80, reg82, reg84, out; + int i; + + reg80 = rtl818x_ioread16(priv, &priv->map->RFPinsOutput); + reg82 = rtl818x_ioread16(priv, &priv->map->RFPinsEnable); + reg84 = rtl818x_ioread16(priv, &priv->map->RFPinsSelect); + + reg80 &= ~0xF; + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82 | 0x000F); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84 | 0x000F); + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80 | (1 << 2)); + udelay(4); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg80); + udelay(5); + + for (i = 4; i >= 0; i--) { + u16 reg = reg80 | ((addr >> i) & 1); + + if (!(i & 1)) { + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + udelay(1); + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg | (1 << 1)); + udelay(2); + + if (i & 1) { + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, reg); + udelay(1); + } + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(2); + + out = 0; + for (i = 11; i >= 0; i--) { + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(1); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 1)); + udelay(2); + + if (rtl818x_ioread16(priv, &priv->map->RFPinsInput) & (1 << 1)) + out |= 1 << i; + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3)); + udelay(2); + } + + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, + reg80 | (1 << 3) | (1 << 2)); + udelay(2); + + rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, reg82); + rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, reg84); + rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x03A0); + + return out; +} + +static const u16 rtl8225bcd_rxgain[] = { + 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409, + 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541, + 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583, + 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644, + 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688, + 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745, + 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789, + 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793, + 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d, + 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9, + 0x07aa, 0x07ab, 0x07ac, 0x07ad, 0x07b0, 0x07b1, 0x07b2, 0x07b3, + 0x07b4, 0x07b5, 0x07b8, 0x07b9, 0x07ba, 0x07bb, 0x07bb +}; + +static const u8 rtl8225_agc[] = { + 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, 0x9e, + 0x9d, 0x9c, 0x9b, 0x9a, 0x99, 0x98, 0x97, 0x96, + 0x95, 0x94, 0x93, 0x92, 0x91, 0x90, 0x8f, 0x8e, + 0x8d, 0x8c, 0x8b, 0x8a, 0x89, 0x88, 0x87, 0x86, + 0x85, 0x84, 0x83, 0x82, 0x81, 0x80, 0x3f, 0x3e, + 0x3d, 0x3c, 0x3b, 0x3a, 0x39, 0x38, 0x37, 0x36, + 0x35, 0x34, 0x33, 0x32, 0x31, 0x30, 0x2f, 0x2e, + 0x2d, 0x2c, 0x2b, 0x2a, 0x29, 0x28, 0x27, 0x26, + 0x25, 0x24, 0x23, 0x22, 0x21, 0x20, 0x1f, 0x1e, + 0x1d, 0x1c, 0x1b, 0x1a, 0x19, 0x18, 0x17, 0x16, + 0x15, 0x14, 0x13, 0x12, 0x11, 0x10, 0x0f, 0x0e, + 0x0d, 0x0c, 0x0b, 0x0a, 0x09, 0x08, 0x07, 0x06, + 0x05, 0x04, 0x03, 0x02, 0x01, 0x01, 0x01, 0x01, + 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, + 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, + 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x01 +}; + +static const u8 rtl8225_gain[] = { + 0x23, 0x88, 0x7c, 0xa5, /* -82dBm */ + 0x23, 0x88, 0x7c, 0xb5, /* -82dBm */ + 0x23, 0x88, 0x7c, 0xc5, /* -82dBm */ + 0x33, 0x80, 0x79, 0xc5, /* -78dBm */ + 0x43, 0x78, 0x76, 0xc5, /* -74dBm */ + 0x53, 0x60, 0x73, 0xc5, /* -70dBm */ + 0x63, 0x58, 0x70, 0xc5, /* -66dBm */ +}; + +static const u8 rtl8225_threshold[] = { + 0x8d, 0x8d, 0x8d, 0x8d, 0x9d, 0xad, 0xbd +}; + +static const u8 rtl8225_tx_gain_cck_ofdm[] = { + 0x02, 0x06, 0x0e, 0x1e, 0x3e, 0x7e +}; + +static const u8 rtl8225_tx_power_cck[] = { + 0x18, 0x17, 0x15, 0x11, 0x0c, 0x08, 0x04, 0x02, + 0x1b, 0x1a, 0x17, 0x13, 0x0e, 0x09, 0x04, 0x02, + 0x1f, 0x1e, 0x1a, 0x15, 0x10, 0x0a, 0x05, 0x02, + 0x22, 0x21, 0x1d, 0x18, 0x11, 0x0b, 0x06, 0x02, + 0x26, 0x25, 0x21, 0x1b, 0x14, 0x0d, 0x06, 0x03, + 0x2b, 0x2a, 0x25, 0x1e, 0x16, 0x0e, 0x07, 0x03 +}; + +static const u8 rtl8225_tx_power_cck_ch14[] = { + 0x18, 0x17, 0x15, 0x0c, 0x00, 0x00, 0x00, 0x00, + 0x1b, 0x1a, 0x17, 0x0e, 0x00, 0x00, 0x00, 0x00, + 0x1f, 0x1e, 0x1a, 0x0f, 0x00, 0x00, 0x00, 0x00, + 0x22, 0x21, 0x1d, 0x11, 0x00, 0x00, 0x00, 0x00, + 0x26, 0x25, 0x21, 0x13, 0x00, 0x00, 0x00, 0x00, + 0x2b, 0x2a, 0x25, 0x15, 0x00, 0x00, 0x00, 0x00 +}; + +static const u8 rtl8225_tx_power_ofdm[] = { + 0x80, 0x90, 0xa2, 0xb5, 0xcb, 0xe4 +}; + +static const u32 rtl8225_chan[] = { + 0x085c, 0x08dc, 0x095c, 0x09dc, 0x0a5c, 0x0adc, 0x0b5c, + 0x0bdc, 0x0c5c, 0x0cdc, 0x0d5c, 0x0ddc, 0x0e5c, 0x0f72 +}; + +static void rtl8225_rf_set_tx_power(struct ieee80211_hw *dev, int channel) +{ + struct rtl8187_priv *priv = dev->priv; + u8 cck_power, ofdm_power; + const u8 *tmp; + u32 reg; + int i; + + cck_power = priv->channels[channel - 1].val & 0xF; + ofdm_power = priv->channels[channel - 1].val >> 4; + + cck_power = min(cck_power, (u8)11); + ofdm_power = min(ofdm_power, (u8)35); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK, + rtl8225_tx_gain_cck_ofdm[cck_power / 6] >> 1); + + if (channel == 14) + tmp = &rtl8225_tx_power_cck_ch14[(cck_power % 6) * 8]; + else + tmp = &rtl8225_tx_power_cck[(cck_power % 6) * 8]; + + for (i = 0; i < 8; i++) + rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++); + + msleep(1); // FIXME: optional? + + /* anaparam2 on */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl8225_write_phy_ofdm(dev, 2, 0x42); + rtl8225_write_phy_ofdm(dev, 6, 0x00); + rtl8225_write_phy_ofdm(dev, 8, 0x00); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM, + rtl8225_tx_gain_cck_ofdm[ofdm_power / 6] >> 1); + + tmp = &rtl8225_tx_power_ofdm[ofdm_power % 6]; + + rtl8225_write_phy_ofdm(dev, 5, *tmp); + rtl8225_write_phy_ofdm(dev, 7, *tmp); + + msleep(1); +} + +void rtl8225_rf_init(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + int i; + + rtl8225_write(dev, 0x0, 0x067); msleep(1); + rtl8225_write(dev, 0x1, 0xFE0); msleep(1); + rtl8225_write(dev, 0x2, 0x44D); msleep(1); + rtl8225_write(dev, 0x3, 0x441); msleep(1); + rtl8225_write(dev, 0x4, 0x486); msleep(1); + rtl8225_write(dev, 0x5, 0xBC0); msleep(1); + rtl8225_write(dev, 0x6, 0xAE6); msleep(1); + rtl8225_write(dev, 0x7, 0x82A); msleep(1); + rtl8225_write(dev, 0x8, 0x01F); msleep(1); + rtl8225_write(dev, 0x9, 0x334); msleep(1); + rtl8225_write(dev, 0xA, 0xFD4); msleep(1); + rtl8225_write(dev, 0xB, 0x391); msleep(1); + rtl8225_write(dev, 0xC, 0x050); msleep(1); + rtl8225_write(dev, 0xD, 0x6DB); msleep(1); + rtl8225_write(dev, 0xE, 0x029); msleep(1); + rtl8225_write(dev, 0xF, 0x914); msleep(100); + + rtl8225_write(dev, 0x2, 0xC4D); msleep(200); + rtl8225_write(dev, 0x2, 0x44D); msleep(200); + + if (!(rtl8225_read(dev, 6) & (1 << 7))) { + rtl8225_write(dev, 0x02, 0x0c4d); + msleep(200); + rtl8225_write(dev, 0x02, 0x044d); + msleep(100); + if (!(rtl8225_read(dev, 6) & (1 << 7))) + printk(KERN_WARNING "%s: RF Calibration Failed! %x\n", + wiphy_name(dev->wiphy), rtl8225_read(dev, 6)); + } + + rtl8225_write(dev, 0x0, 0x127); + + for (i = 0; i < ARRAY_SIZE(rtl8225bcd_rxgain); i++) { + rtl8225_write(dev, 0x1, i + 1); + rtl8225_write(dev, 0x2, rtl8225bcd_rxgain[i]); + } + + rtl8225_write(dev, 0x0, 0x027); + rtl8225_write(dev, 0x0, 0x22F); + + for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) { + rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]); + msleep(1); + rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i); + msleep(1); + } + + msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x00, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x01, 0x02); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x02, 0x42); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x03, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x04, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x05, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x06, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x07, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x08, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0a, 0x09); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x10, 0x84); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x11, 0x06); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x12, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x13, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x14, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x15, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x16, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x17, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x18, 0xef); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x19, 0x19); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1b, 0x76); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1e, 0x95); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x21, 0x27); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x22, 0x16); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x24, 0x46); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x25, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x27, 0x88); msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[2 * 4]); + rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[2 * 4 + 2]); + rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[2 * 4 + 3]); + rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[2 * 4 + 1]); + + rtl8225_write_phy_cck(dev, 0x00, 0x98); msleep(1); + rtl8225_write_phy_cck(dev, 0x03, 0x20); msleep(1); + rtl8225_write_phy_cck(dev, 0x04, 0x7e); msleep(1); + rtl8225_write_phy_cck(dev, 0x05, 0x12); msleep(1); + rtl8225_write_phy_cck(dev, 0x06, 0xfc); msleep(1); + rtl8225_write_phy_cck(dev, 0x07, 0x78); msleep(1); + rtl8225_write_phy_cck(dev, 0x08, 0x2e); msleep(1); + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); + rtl8225_write_phy_cck(dev, 0x11, 0x88); msleep(1); + rtl8225_write_phy_cck(dev, 0x12, 0x47); msleep(1); + rtl8225_write_phy_cck(dev, 0x13, 0xd0); + rtl8225_write_phy_cck(dev, 0x19, 0x00); + rtl8225_write_phy_cck(dev, 0x1a, 0xa0); + rtl8225_write_phy_cck(dev, 0x1b, 0x08); + rtl8225_write_phy_cck(dev, 0x40, 0x86); + rtl8225_write_phy_cck(dev, 0x41, 0x8d); msleep(1); + rtl8225_write_phy_cck(dev, 0x42, 0x15); msleep(1); + rtl8225_write_phy_cck(dev, 0x43, 0x18); msleep(1); + rtl8225_write_phy_cck(dev, 0x44, 0x1f); msleep(1); + rtl8225_write_phy_cck(dev, 0x45, 0x1e); msleep(1); + rtl8225_write_phy_cck(dev, 0x46, 0x1a); msleep(1); + rtl8225_write_phy_cck(dev, 0x47, 0x15); msleep(1); + rtl8225_write_phy_cck(dev, 0x48, 0x10); msleep(1); + rtl8225_write_phy_cck(dev, 0x49, 0x0a); msleep(1); + rtl8225_write_phy_cck(dev, 0x4a, 0x05); msleep(1); + rtl8225_write_phy_cck(dev, 0x4b, 0x02); msleep(1); + rtl8225_write_phy_cck(dev, 0x4c, 0x05); msleep(1); + + rtl818x_iowrite8(priv, &priv->map->TESTR, 0x0D); + + rtl8225_rf_set_tx_power(dev, 1); + + /* RX antenna default to A */ + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); /* B: 0xDB */ + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); /* B: 0x10 */ + + rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */ + msleep(1); + rtl818x_iowrite32(priv, (__le32 *)0xFF94, 0x3dc00002); + + /* set sensitivity */ + rtl8225_write(dev, 0x0c, 0x50); + rtl8225_write_phy_ofdm(dev, 0x0d, rtl8225_gain[2 * 4]); + rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225_gain[2 * 4 + 2]); + rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225_gain[2 * 4 + 3]); + rtl8225_write_phy_ofdm(dev, 0x23, rtl8225_gain[2 * 4 + 1]); + rtl8225_write_phy_cck(dev, 0x41, rtl8225_threshold[2]); +} + +static const u8 rtl8225z2_tx_power_cck_ch14[] = { + 0x36, 0x35, 0x2e, 0x1b, 0x00, 0x00, 0x00, 0x00 +}; + +static const u8 rtl8225z2_tx_power_cck[] = { + 0x36, 0x35, 0x2e, 0x25, 0x1c, 0x12, 0x09, 0x04 +}; + +static const u8 rtl8225z2_tx_power_ofdm[] = { + 0x42, 0x00, 0x40, 0x00, 0x40 +}; + +static const u8 rtl8225z2_tx_gain_cck_ofdm[] = { + 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, + 0x06, 0x07, 0x08, 0x09, 0x0a, 0x0b, + 0x0c, 0x0d, 0x0e, 0x0f, 0x10, 0x11, + 0x12, 0x13, 0x14, 0x15, 0x16, 0x17, + 0x18, 0x19, 0x1a, 0x1b, 0x1c, 0x1d, + 0x1e, 0x1f, 0x20, 0x21, 0x22, 0x23 +}; + +static void rtl8225z2_rf_set_tx_power(struct ieee80211_hw *dev, int channel) +{ + struct rtl8187_priv *priv = dev->priv; + u8 cck_power, ofdm_power; + const u8 *tmp; + u32 reg; + int i; + + cck_power = priv->channels[channel - 1].val & 0xF; + ofdm_power = priv->channels[channel - 1].val >> 4; + + cck_power = min(cck_power, (u8)15); + cck_power += priv->txpwr_base & 0xF; + cck_power = min(cck_power, (u8)35); + + ofdm_power = min(ofdm_power, (u8)15); + ofdm_power += priv->txpwr_base >> 4; + ofdm_power = min(ofdm_power, (u8)35); + + if (channel == 14) + tmp = rtl8225z2_tx_power_cck_ch14; + else + tmp = rtl8225z2_tx_power_cck; + + for (i = 0; i < 8; i++) + rtl8225_write_phy_cck(dev, 0x44 + i, *tmp++); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_CCK, + rtl8225z2_tx_gain_cck_ofdm[cck_power]); + msleep(1); + + /* anaparam2 on */ + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_ON); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); + + rtl8225_write_phy_ofdm(dev, 2, 0x42); + rtl8225_write_phy_ofdm(dev, 5, 0x00); + rtl8225_write_phy_ofdm(dev, 6, 0x40); + rtl8225_write_phy_ofdm(dev, 7, 0x00); + rtl8225_write_phy_ofdm(dev, 8, 0x40); + + rtl818x_iowrite8(priv, &priv->map->TX_GAIN_OFDM, + rtl8225z2_tx_gain_cck_ofdm[ofdm_power]); + msleep(1); +} + +static const u16 rtl8225z2_rxgain[] = { + 0x0400, 0x0401, 0x0402, 0x0403, 0x0404, 0x0405, 0x0408, 0x0409, + 0x040a, 0x040b, 0x0502, 0x0503, 0x0504, 0x0505, 0x0540, 0x0541, + 0x0542, 0x0543, 0x0544, 0x0545, 0x0580, 0x0581, 0x0582, 0x0583, + 0x0584, 0x0585, 0x0588, 0x0589, 0x058a, 0x058b, 0x0643, 0x0644, + 0x0645, 0x0680, 0x0681, 0x0682, 0x0683, 0x0684, 0x0685, 0x0688, + 0x0689, 0x068a, 0x068b, 0x068c, 0x0742, 0x0743, 0x0744, 0x0745, + 0x0780, 0x0781, 0x0782, 0x0783, 0x0784, 0x0785, 0x0788, 0x0789, + 0x078a, 0x078b, 0x078c, 0x078d, 0x0790, 0x0791, 0x0792, 0x0793, + 0x0794, 0x0795, 0x0798, 0x0799, 0x079a, 0x079b, 0x079c, 0x079d, + 0x07a0, 0x07a1, 0x07a2, 0x07a3, 0x07a4, 0x07a5, 0x07a8, 0x07a9, + 0x03aa, 0x03ab, 0x03ac, 0x03ad, 0x03b0, 0x03b1, 0x03b2, 0x03b3, + 0x03b4, 0x03b5, 0x03b8, 0x03b9, 0x03ba, 0x03bb, 0x03bb +}; + +static const u8 rtl8225z2_gain_bg[] = { + 0x23, 0x15, 0xa5, /* -82-1dBm */ + 0x23, 0x15, 0xb5, /* -82-2dBm */ + 0x23, 0x15, 0xc5, /* -82-3dBm */ + 0x33, 0x15, 0xc5, /* -78dBm */ + 0x43, 0x15, 0xc5, /* -74dBm */ + 0x53, 0x15, 0xc5, /* -70dBm */ + 0x63, 0x15, 0xc5 /* -66dBm */ +}; + +void rtl8225z2_rf_init(struct ieee80211_hw *dev) +{ + struct rtl8187_priv *priv = dev->priv; + int i; + + rtl8225_write(dev, 0x0, 0x2BF); msleep(1); + rtl8225_write(dev, 0x1, 0xEE0); msleep(1); + rtl8225_write(dev, 0x2, 0x44D); msleep(1); + rtl8225_write(dev, 0x3, 0x441); msleep(1); + rtl8225_write(dev, 0x4, 0x8C3); msleep(1); + rtl8225_write(dev, 0x5, 0xC72); msleep(1); + rtl8225_write(dev, 0x6, 0x0E6); msleep(1); + rtl8225_write(dev, 0x7, 0x82A); msleep(1); + rtl8225_write(dev, 0x8, 0x03F); msleep(1); + rtl8225_write(dev, 0x9, 0x335); msleep(1); + rtl8225_write(dev, 0xa, 0x9D4); msleep(1); + rtl8225_write(dev, 0xb, 0x7BB); msleep(1); + rtl8225_write(dev, 0xc, 0x850); msleep(1); + rtl8225_write(dev, 0xd, 0xCDF); msleep(1); + rtl8225_write(dev, 0xe, 0x02B); msleep(1); + rtl8225_write(dev, 0xf, 0x114); msleep(100); + + rtl8225_write(dev, 0x0, 0x1B7); + + for (i = 0; i < ARRAY_SIZE(rtl8225z2_rxgain); i++) { + rtl8225_write(dev, 0x1, i + 1); + rtl8225_write(dev, 0x2, rtl8225z2_rxgain[i]); + } + + rtl8225_write(dev, 0x3, 0x080); + rtl8225_write(dev, 0x5, 0x004); + rtl8225_write(dev, 0x0, 0x0B7); + rtl8225_write(dev, 0x2, 0xc4D); + + msleep(200); + rtl8225_write(dev, 0x2, 0x44D); + msleep(100); + + if (!(rtl8225_read(dev, 6) & (1 << 7))) { + rtl8225_write(dev, 0x02, 0x0C4D); + msleep(200); + rtl8225_write(dev, 0x02, 0x044D); + msleep(100); + if (!(rtl8225_read(dev, 6) & (1 << 7))) + printk(KERN_WARNING "%s: RF Calibration Failed! %x\n", + wiphy_name(dev->wiphy), rtl8225_read(dev, 6)); + } + + msleep(200); + + rtl8225_write(dev, 0x0, 0x2BF); + + for (i = 0; i < ARRAY_SIZE(rtl8225_agc); i++) { + rtl8225_write_phy_ofdm(dev, 0xB, rtl8225_agc[i]); + msleep(1); + rtl8225_write_phy_ofdm(dev, 0xA, 0x80 + i); + msleep(1); + } + + msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x00, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x01, 0x02); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x02, 0x42); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x03, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x04, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x05, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x06, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x07, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x08, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x09, 0xfe); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0a, 0x08); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0b, 0x80); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0c, 0x01); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0d, 0x43); + rtl8225_write_phy_ofdm(dev, 0x0e, 0xd3); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x0f, 0x38); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x10, 0x84); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x11, 0x07); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x12, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x13, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x14, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x15, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x16, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x17, 0x40); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x18, 0xef); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x19, 0x19); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1a, 0x20); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1b, 0x15); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1c, 0x04); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1d, 0xc5); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1e, 0x95); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x1f, 0x75); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x20, 0x1f); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x21, 0x17); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x22, 0x16); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x23, 0x80); msleep(1); //FIXME: not needed? + rtl8225_write_phy_ofdm(dev, 0x24, 0x46); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x25, 0x00); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); + rtl8225_write_phy_ofdm(dev, 0x27, 0x88); msleep(1); + + rtl8225_write_phy_ofdm(dev, 0x0b, rtl8225z2_gain_bg[4 * 3]); + rtl8225_write_phy_ofdm(dev, 0x1b, rtl8225z2_gain_bg[4 * 3 + 1]); + rtl8225_write_phy_ofdm(dev, 0x1d, rtl8225z2_gain_bg[4 * 3 + 2]); + rtl8225_write_phy_ofdm(dev, 0x21, 0x37); + + rtl8225_write_phy_cck(dev, 0x00, 0x98); msleep(1); + rtl8225_write_phy_cck(dev, 0x03, 0x20); msleep(1); + rtl8225_write_phy_cck(dev, 0x04, 0x7e); msleep(1); + rtl8225_write_phy_cck(dev, 0x05, 0x12); msleep(1); + rtl8225_write_phy_cck(dev, 0x06, 0xfc); msleep(1); + rtl8225_write_phy_cck(dev, 0x07, 0x78); msleep(1); + rtl8225_write_phy_cck(dev, 0x08, 0x2e); msleep(1); + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); + rtl8225_write_phy_cck(dev, 0x11, 0x88); msleep(1); + rtl8225_write_phy_cck(dev, 0x12, 0x47); msleep(1); + rtl8225_write_phy_cck(dev, 0x13, 0xd0); + rtl8225_write_phy_cck(dev, 0x19, 0x00); + rtl8225_write_phy_cck(dev, 0x1a, 0xa0); + rtl8225_write_phy_cck(dev, 0x1b, 0x08); + rtl8225_write_phy_cck(dev, 0x40, 0x86); + rtl8225_write_phy_cck(dev, 0x41, 0x8d); msleep(1); + rtl8225_write_phy_cck(dev, 0x42, 0x15); msleep(1); + rtl8225_write_phy_cck(dev, 0x43, 0x18); msleep(1); + rtl8225_write_phy_cck(dev, 0x44, 0x36); msleep(1); + rtl8225_write_phy_cck(dev, 0x45, 0x35); msleep(1); + rtl8225_write_phy_cck(dev, 0x46, 0x2e); msleep(1); + rtl8225_write_phy_cck(dev, 0x47, 0x25); msleep(1); + rtl8225_write_phy_cck(dev, 0x48, 0x1c); msleep(1); + rtl8225_write_phy_cck(dev, 0x49, 0x12); msleep(1); + rtl8225_write_phy_cck(dev, 0x4a, 0x09); msleep(1); + rtl8225_write_phy_cck(dev, 0x4b, 0x04); msleep(1); + rtl8225_write_phy_cck(dev, 0x4c, 0x05); msleep(1); + + rtl818x_iowrite8(priv, (u8 *)0xFF5B, 0x0D); msleep(1); + + rtl8225z2_rf_set_tx_power(dev, 1); + + /* RX antenna default to A */ + rtl8225_write_phy_cck(dev, 0x10, 0x9b); msleep(1); /* B: 0xDB */ + rtl8225_write_phy_ofdm(dev, 0x26, 0x90); msleep(1); /* B: 0x10 */ + + rtl818x_iowrite8(priv, &priv->map->TX_ANTENNA, 0x03); /* B: 0x00 */ + msleep(1); + rtl818x_iowrite32(priv, (__le32 *)0xFF94, 0x3dc00002); +} + +void rtl8225_rf_stop(struct ieee80211_hw *dev) +{ + u8 reg; + struct rtl8187_priv *priv = dev->priv; + + rtl8225_write(dev, 0x4, 0x1f); msleep(1); + + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); + reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg | RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, RTL8225_ANAPARAM2_OFF); + rtl818x_iowrite32(priv, &priv->map->ANAPARAM, RTL8225_ANAPARAM_OFF); + rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg & ~RTL818X_CONFIG3_ANAPARAM_WRITE); + rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); +} + +void rtl8225_rf_set_channel(struct ieee80211_hw *dev, int channel) +{ + struct rtl8187_priv *priv = dev->priv; + + if (priv->rf_init == rtl8225_rf_init) + rtl8225_rf_set_tx_power(dev, channel); + else + rtl8225z2_rf_set_tx_power(dev, channel); + + rtl8225_write(dev, 0x7, rtl8225_chan[channel - 1]); + msleep(10); +} diff --git a/drivers/net/wireless/rtl8187_rtl8225.h b/drivers/net/wireless/rtl8187_rtl8225.h new file mode 100644 index 00000000000..798ba4a9737 --- /dev/null +++ b/drivers/net/wireless/rtl8187_rtl8225.h @@ -0,0 +1,44 @@ +/* + * Radio tuning definitions for RTL8225 on RTL8187 + * + * Copyright 2007 Michael Wu <flamingice@sourmilk.net> + * Copyright 2007 Andrea Merello <andreamrl@tiscali.it> + * + * Based on the r8187 driver, which is: + * Copyright 2005 Andrea Merello <andreamrl@tiscali.it>, et al. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef RTL8187_RTL8225_H +#define RTL8187_RTL8225_H + +#define RTL8225_ANAPARAM_ON 0xa0000a59 +#define RTL8225_ANAPARAM2_ON 0x860c7312 +#define RTL8225_ANAPARAM_OFF 0xa00beb59 +#define RTL8225_ANAPARAM2_OFF 0x840dec11 + +void rtl8225_write(struct ieee80211_hw *, u8 addr, u16 data); +u16 rtl8225_read(struct ieee80211_hw *, u8 addr); + +void rtl8225_rf_init(struct ieee80211_hw *); +void rtl8225z2_rf_init(struct ieee80211_hw *); +void rtl8225_rf_stop(struct ieee80211_hw *); +void rtl8225_rf_set_channel(struct ieee80211_hw *, int); + + +static inline void rtl8225_write_phy_ofdm(struct ieee80211_hw *dev, + u8 addr, u32 data) +{ + rtl8187_write_phy(dev, addr, data); +} + +static inline void rtl8225_write_phy_cck(struct ieee80211_hw *dev, + u8 addr, u32 data) +{ + rtl8187_write_phy(dev, addr, data | 0x10000); +} + +#endif /* RTL8187_RTL8225_H */ diff --git a/drivers/net/wireless/rtl818x.h b/drivers/net/wireless/rtl818x.h new file mode 100644 index 00000000000..283de30628e --- /dev/null +++ b/drivers/net/wireless/rtl818x.h @@ -0,0 +1,226 @@ +/* + * Definitions for RTL818x hardware + * + * Copyright 2007 Michael Wu <flamingice@sourmilk.net> + * Copyright 2007 Andrea Merello <andreamrl@tiscali.it> + * + * Based on the r8187 driver, which is: + * Copyright 2005 Andrea Merello <andreamrl@tiscali.it>, et al. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#ifndef RTL818X_H +#define RTL818X_H + +struct rtl818x_csr { + u8 MAC[6]; + u8 reserved_0[2]; + __le32 MAR[2]; + u8 RX_FIFO_COUNT; + u8 reserved_1; + u8 TX_FIFO_COUNT; + u8 BQREQ; + u8 reserved_2[4]; + __le32 TSFT[2]; + __le32 TLPDA; + __le32 TNPDA; + __le32 THPDA; + __le16 BRSR; + u8 BSSID[6]; + u8 RESP_RATE; + u8 EIFS; + u8 reserved_3[1]; + u8 CMD; +#define RTL818X_CMD_TX_ENABLE (1 << 2) +#define RTL818X_CMD_RX_ENABLE (1 << 3) +#define RTL818X_CMD_RESET (1 << 4) + u8 reserved_4[4]; + __le16 INT_MASK; + __le16 INT_STATUS; +#define RTL818X_INT_RX_OK (1 << 0) +#define RTL818X_INT_RX_ERR (1 << 1) +#define RTL818X_INT_TXL_OK (1 << 2) +#define RTL818X_INT_TXL_ERR (1 << 3) +#define RTL818X_INT_RX_DU (1 << 4) +#define RTL818X_INT_RX_FO (1 << 5) +#define RTL818X_INT_TXN_OK (1 << 6) +#define RTL818X_INT_TXN_ERR (1 << 7) +#define RTL818X_INT_TXH_OK (1 << 8) +#define RTL818X_INT_TXH_ERR (1 << 9) +#define RTL818X_INT_TXB_OK (1 << 10) +#define RTL818X_INT_TXB_ERR (1 << 11) +#define RTL818X_INT_ATIM (1 << 12) +#define RTL818X_INT_BEACON (1 << 13) +#define RTL818X_INT_TIME_OUT (1 << 14) +#define RTL818X_INT_TX_FO (1 << 15) + __le32 TX_CONF; +#define RTL818X_TX_CONF_LOOPBACK_MAC (1 << 17) +#define RTL818X_TX_CONF_NO_ICV (1 << 19) +#define RTL818X_TX_CONF_DISCW (1 << 20) +#define RTL818X_TX_CONF_R8180_ABCD (2 << 25) +#define RTL818X_TX_CONF_R8180_F (3 << 25) +#define RTL818X_TX_CONF_R8185_ABC (4 << 25) +#define RTL818X_TX_CONF_R8185_D (5 << 25) +#define RTL818X_TX_CONF_HWVER_MASK (7 << 25) +#define RTL818X_TX_CONF_CW_MIN (1 << 31) + __le32 RX_CONF; +#define RTL818X_RX_CONF_MONITOR (1 << 0) +#define RTL818X_RX_CONF_NICMAC (1 << 1) +#define RTL818X_RX_CONF_MULTICAST (1 << 2) +#define RTL818X_RX_CONF_BROADCAST (1 << 3) +#define RTL818X_RX_CONF_DATA (1 << 18) +#define RTL818X_RX_CONF_CTRL (1 << 19) +#define RTL818X_RX_CONF_MGMT (1 << 20) +#define RTL818X_RX_CONF_BSSID (1 << 23) +#define RTL818X_RX_CONF_RX_AUTORESETPHY (1 << 28) +#define RTL818X_RX_CONF_ONLYERLPKT (1 << 31) + __le32 INT_TIMEOUT; + __le32 TBDA; + u8 EEPROM_CMD; +#define RTL818X_EEPROM_CMD_READ (1 << 0) +#define RTL818X_EEPROM_CMD_WRITE (1 << 1) +#define RTL818X_EEPROM_CMD_CK (1 << 2) +#define RTL818X_EEPROM_CMD_CS (1 << 3) +#define RTL818X_EEPROM_CMD_NORMAL (0 << 6) +#define RTL818X_EEPROM_CMD_LOAD (1 << 6) +#define RTL818X_EEPROM_CMD_PROGRAM (2 << 6) +#define RTL818X_EEPROM_CMD_CONFIG (3 << 6) + u8 CONFIG0; + u8 CONFIG1; + u8 CONFIG2; + __le32 ANAPARAM; + u8 MSR; +#define RTL818X_MSR_NO_LINK (0 << 2) +#define RTL818X_MSR_ADHOC (1 << 2) +#define RTL818X_MSR_INFRA (2 << 2) + u8 CONFIG3; +#define RTL818X_CONFIG3_ANAPARAM_WRITE (1 << 6) + u8 CONFIG4; +#define RTL818X_CONFIG4_POWEROFF (1 << 6) +#define RTL818X_CONFIG4_VCOOFF (1 << 7) + u8 TESTR; + u8 reserved_9[2]; + __le16 PGSELECT; + __le32 ANAPARAM2; + u8 reserved_10[12]; + __le16 BEACON_INTERVAL; + __le16 ATIM_WND; + __le16 BEACON_INTERVAL_TIME; + __le16 ATIMTR_INTERVAL; + u8 reserved_11[4]; + u8 PHY[4]; + __le16 RFPinsOutput; + __le16 RFPinsEnable; + __le16 RFPinsSelect; + __le16 RFPinsInput; + __le32 RF_PARA; + __le32 RF_TIMING; + u8 GP_ENABLE; + u8 GPIO; + u8 reserved_12[10]; + u8 TX_AGC_CTL; +#define RTL818X_TX_AGC_CTL_PERPACKET_GAIN_SHIFT (1 << 0) +#define RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL_SHIFT (1 << 1) +#define RTL818X_TX_AGC_CTL_FEEDBACK_ANT (1 << 2) + u8 TX_GAIN_CCK; + u8 TX_GAIN_OFDM; + u8 TX_ANTENNA; + u8 reserved_13[16]; + u8 WPA_CONF; + u8 reserved_14[3]; + u8 SIFS; + u8 DIFS; + u8 SLOT; + u8 reserved_15[5]; + u8 CW_CONF; +#define RTL818X_CW_CONF_PERPACKET_CW_SHIFT (1 << 0) +#define RTL818X_CW_CONF_PERPACKET_RETRY_SHIFT (1 << 1) + u8 CW_VAL; + u8 RATE_FALLBACK; + u8 reserved_16[25]; + u8 CONFIG5; + u8 TX_DMA_POLLING; + u8 reserved_17[2]; + __le16 CWR; + u8 RETRY_CTR; + u8 reserved_18[5]; + __le32 RDSAR; + u8 reserved_19[18]; + u16 TALLY_CNT; + u8 TALLY_SEL; +} __attribute__((packed)); + +static const struct ieee80211_rate rtl818x_rates[] = { + { .rate = 10, + .val = 0, + .flags = IEEE80211_RATE_CCK }, + { .rate = 20, + .val = 1, + .flags = IEEE80211_RATE_CCK }, + { .rate = 55, + .val = 2, + .flags = IEEE80211_RATE_CCK }, + { .rate = 110, + .val = 3, + .flags = IEEE80211_RATE_CCK }, + { .rate = 60, + .val = 4, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 90, + .val = 5, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 120, + .val = 6, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 180, + .val = 7, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 240, + .val = 8, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 360, + .val = 9, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 480, + .val = 10, + .flags = IEEE80211_RATE_OFDM }, + { .rate = 540, + .val = 11, + .flags = IEEE80211_RATE_OFDM }, +}; + +static const struct ieee80211_channel rtl818x_channels[] = { + { .chan = 1, + .freq = 2412}, + { .chan = 2, + .freq = 2417}, + { .chan = 3, + .freq = 2422}, + { .chan = 4, + .freq = 2427}, + { .chan = 5, + .freq = 2432}, + { .chan = 6, + .freq = 2437}, + { .chan = 7, + .freq = 2442}, + { .chan = 8, + .freq = 2447}, + { .chan = 9, + .freq = 2452}, + { .chan = 10, + .freq = 2457}, + { .chan = 11, + .freq = 2462}, + { .chan = 12, + .freq = 2467}, + { .chan = 13, + .freq = 2472}, + { .chan = 14, + .freq = 2484} +}; + +#endif /* RTL818X_H */ diff --git a/drivers/net/wireless/zd1211rw/Makefile b/drivers/net/wireless/zd1211rw/Makefile index 6603ad5be63..4d505903352 100644 --- a/drivers/net/wireless/zd1211rw/Makefile +++ b/drivers/net/wireless/zd1211rw/Makefile @@ -3,7 +3,7 @@ obj-$(CONFIG_ZD1211RW) += zd1211rw.o zd1211rw-objs := zd_chip.o zd_ieee80211.o \ zd_mac.o zd_netdev.o \ zd_rf_al2230.o zd_rf_rf2959.o \ - zd_rf_al7230b.o \ + zd_rf_al7230b.o zd_rf_uw2453.o \ zd_rf.o zd_usb.o zd_util.o ifeq ($(CONFIG_ZD1211RW_DEBUG),y) diff --git a/drivers/net/wireless/zd1211rw/zd_chip.c b/drivers/net/wireless/zd1211rw/zd_chip.c index 95b4a2a2670..5b624bfc01a 100644 --- a/drivers/net/wireless/zd1211rw/zd_chip.c +++ b/drivers/net/wireless/zd1211rw/zd_chip.c @@ -1253,6 +1253,9 @@ static int update_channel_integration_and_calibration(struct zd_chip *chip, { int r; + if (!zd_rf_should_update_pwr_int(&chip->rf)) + return 0; + r = update_pwr_int(chip, channel); if (r) return r; @@ -1283,7 +1286,7 @@ static int patch_cck_gain(struct zd_chip *chip) int r; u32 value; - if (!chip->patch_cck_gain) + if (!chip->patch_cck_gain || !zd_rf_should_patch_cck_gain(&chip->rf)) return 0; ZD_ASSERT(mutex_is_locked(&chip->mutex)); diff --git a/drivers/net/wireless/zd1211rw/zd_chip.h b/drivers/net/wireless/zd1211rw/zd_chip.h index ce0a5f6da0d..79d0288c193 100644 --- a/drivers/net/wireless/zd1211rw/zd_chip.h +++ b/drivers/net/wireless/zd1211rw/zd_chip.h @@ -608,6 +608,9 @@ enum { #define CR_ZD1211B_TXOP CTL_REG(0x0b20) #define CR_ZD1211B_RETRY_MAX CTL_REG(0x0b28) +/* Used to detect PLL lock */ +#define UW2453_INTR_REG ((zd_addr_t)0x85c1) + #define CWIN_SIZE 0x007f043f diff --git a/drivers/net/wireless/zd1211rw/zd_rf.c b/drivers/net/wireless/zd1211rw/zd_rf.c index 549c23bcd6c..7407409b60b 100644 --- a/drivers/net/wireless/zd1211rw/zd_rf.c +++ b/drivers/net/wireless/zd1211rw/zd_rf.c @@ -52,34 +52,38 @@ const char *zd_rf_name(u8 type) void zd_rf_init(struct zd_rf *rf) { memset(rf, 0, sizeof(*rf)); + + /* default to update channel integration, as almost all RF's do want + * this */ + rf->update_channel_int = 1; } void zd_rf_clear(struct zd_rf *rf) { + if (rf->clear) + rf->clear(rf); ZD_MEMCLEAR(rf, sizeof(*rf)); } int zd_rf_init_hw(struct zd_rf *rf, u8 type) { - int r, t; + int r = 0; + int t; struct zd_chip *chip = zd_rf_to_chip(rf); ZD_ASSERT(mutex_is_locked(&chip->mutex)); switch (type) { case RF2959_RF: r = zd_rf_init_rf2959(rf); - if (r) - return r; break; case AL2230_RF: r = zd_rf_init_al2230(rf); - if (r) - return r; break; case AL7230B_RF: r = zd_rf_init_al7230b(rf); - if (r) - return r; + break; + case UW2453_RF: + r = zd_rf_init_uw2453(rf); break; default: dev_err(zd_chip_dev(chip), @@ -88,6 +92,9 @@ int zd_rf_init_hw(struct zd_rf *rf, u8 type) return -ENODEV; } + if (r) + return r; + rf->type = type; r = zd_chip_lock_phy_regs(chip); diff --git a/drivers/net/wireless/zd1211rw/zd_rf.h b/drivers/net/wireless/zd1211rw/zd_rf.h index aa9cc105ce6..c6dfd8227f6 100644 --- a/drivers/net/wireless/zd1211rw/zd_rf.h +++ b/drivers/net/wireless/zd1211rw/zd_rf.h @@ -48,12 +48,26 @@ struct zd_rf { u8 channel; + /* whether channel integration and calibration should be updated + * defaults to 1 (yes) */ + u8 update_channel_int:1; + + /* whether CR47 should be patched from the EEPROM, if the appropriate + * flag is set in the POD. The vendor driver suggests that this should + * be done for all RF's, but a bug in their code prevents but their + * HW_OverWritePhyRegFromE2P() routine from ever taking effect. */ + u8 patch_cck_gain:1; + + /* private RF driver data */ + void *priv; + /* RF-specific functions */ int (*init_hw)(struct zd_rf *rf); int (*set_channel)(struct zd_rf *rf, u8 channel); int (*switch_radio_on)(struct zd_rf *rf); int (*switch_radio_off)(struct zd_rf *rf); int (*patch_6m_band_edge)(struct zd_rf *rf, u8 channel); + void (*clear)(struct zd_rf *rf); }; const char *zd_rf_name(u8 type); @@ -71,10 +85,24 @@ int zd_switch_radio_off(struct zd_rf *rf); int zd_rf_patch_6m_band_edge(struct zd_rf *rf, u8 channel); int zd_rf_generic_patch_6m(struct zd_rf *rf, u8 channel); +static inline int zd_rf_should_update_pwr_int(struct zd_rf *rf) +{ + return rf->update_channel_int; +} + +static inline int zd_rf_should_patch_cck_gain(struct zd_rf *rf) +{ + return rf->patch_cck_gain; +} + +int zd_rf_patch_6m_band_edge(struct zd_rf *rf, u8 channel); +int zd_rf_generic_patch_6m(struct zd_rf *rf, u8 channel); + /* Functions for individual RF chips */ int zd_rf_init_rf2959(struct zd_rf *rf); int zd_rf_init_al2230(struct zd_rf *rf); int zd_rf_init_al7230b(struct zd_rf *rf); +int zd_rf_init_uw2453(struct zd_rf *rf); #endif /* _ZD_RF_H */ diff --git a/drivers/net/wireless/zd1211rw/zd_rf_al2230.c b/drivers/net/wireless/zd1211rw/zd_rf_al2230.c index 511392acfed..e7a4ecf7b6e 100644 --- a/drivers/net/wireless/zd1211rw/zd_rf_al2230.c +++ b/drivers/net/wireless/zd1211rw/zd_rf_al2230.c @@ -432,5 +432,6 @@ int zd_rf_init_al2230(struct zd_rf *rf) rf->switch_radio_on = zd1211_al2230_switch_radio_on; } rf->patch_6m_band_edge = zd_rf_generic_patch_6m; + rf->patch_cck_gain = 1; return 0; } diff --git a/drivers/net/wireless/zd1211rw/zd_rf_al7230b.c b/drivers/net/wireless/zd1211rw/zd_rf_al7230b.c index 5e5e9ddc6a7..f4e8b6ada85 100644 --- a/drivers/net/wireless/zd1211rw/zd_rf_al7230b.c +++ b/drivers/net/wireless/zd1211rw/zd_rf_al7230b.c @@ -483,6 +483,7 @@ int zd_rf_init_al7230b(struct zd_rf *rf) rf->switch_radio_on = zd1211_al7230b_switch_radio_on; rf->set_channel = zd1211_al7230b_set_channel; rf->patch_6m_band_edge = zd_rf_generic_patch_6m; + rf->patch_cck_gain = 1; } rf->switch_radio_off = al7230b_switch_radio_off; diff --git a/drivers/net/wireless/zd1211rw/zd_rf_uw2453.c b/drivers/net/wireless/zd1211rw/zd_rf_uw2453.c new file mode 100644 index 00000000000..414e40d571a --- /dev/null +++ b/drivers/net/wireless/zd1211rw/zd_rf_uw2453.c @@ -0,0 +1,534 @@ +/* zd_rf_uw2453.c: Functions for the UW2453 RF controller + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + */ + +#include <linux/kernel.h> + +#include "zd_rf.h" +#include "zd_usb.h" +#include "zd_chip.h" + +/* This RF programming code is based upon the code found in v2.16.0.0 of the + * ZyDAS vendor driver. Unlike other RF's, Ubec publish full technical specs + * for this RF on their website, so we're able to understand more than + * usual as to what is going on. Thumbs up for Ubec for doing that. */ + +/* The 3-wire serial interface provides access to 8 write-only registers. + * The data format is a 4 bit register address followed by a 20 bit value. */ +#define UW2453_REGWRITE(reg, val) ((((reg) & 0xf) << 20) | ((val) & 0xfffff)) + +/* For channel tuning, we have to configure registers 1 (synthesizer), 2 (synth + * fractional divide ratio) and 3 (VCO config). + * + * We configure the RF to produce an interrupt when the PLL is locked onto + * the configured frequency. During initialization, we run through a variety + * of different VCO configurations on channel 1 until we detect a PLL lock. + * When this happens, we remember which VCO configuration produced the lock + * and use it later. Actually, we use the configuration *after* the one that + * produced the lock, which seems odd, but it works. + * + * If we do not see a PLL lock on any standard VCO config, we fall back on an + * autocal configuration, which has a fixed (as opposed to per-channel) VCO + * config and different synth values from the standard set (divide ratio + * is still shared with the standard set). */ + +/* The per-channel synth values for all standard VCO configurations. These get + * written to register 1. */ +static const u8 uw2453_std_synth[] = { + RF_CHANNEL( 1) = 0x47, + RF_CHANNEL( 2) = 0x47, + RF_CHANNEL( 3) = 0x67, + RF_CHANNEL( 4) = 0x67, + RF_CHANNEL( 5) = 0x67, + RF_CHANNEL( 6) = 0x67, + RF_CHANNEL( 7) = 0x57, + RF_CHANNEL( 8) = 0x57, + RF_CHANNEL( 9) = 0x57, + RF_CHANNEL(10) = 0x57, + RF_CHANNEL(11) = 0x77, + RF_CHANNEL(12) = 0x77, + RF_CHANNEL(13) = 0x77, + RF_CHANNEL(14) = 0x4f, +}; + +/* This table stores the synthesizer fractional divide ratio for *all* VCO + * configurations (both standard and autocal). These get written to register 2. + */ +static const u16 uw2453_synth_divide[] = { + RF_CHANNEL( 1) = 0x999, + RF_CHANNEL( 2) = 0x99b, + RF_CHANNEL( 3) = 0x998, + RF_CHANNEL( 4) = 0x99a, + RF_CHANNEL( 5) = 0x999, + RF_CHANNEL( 6) = 0x99b, + RF_CHANNEL( 7) = 0x998, + RF_CHANNEL( 8) = 0x99a, + RF_CHANNEL( 9) = 0x999, + RF_CHANNEL(10) = 0x99b, + RF_CHANNEL(11) = 0x998, + RF_CHANNEL(12) = 0x99a, + RF_CHANNEL(13) = 0x999, + RF_CHANNEL(14) = 0xccc, +}; + +/* Here is the data for all the standard VCO configurations. We shrink our + * table a little by observing that both channels in a consecutive pair share + * the same value. We also observe that the high 4 bits ([0:3] in the specs) + * are all 'Reserved' and are always set to 0x4 - we chop them off in the data + * below. */ +#define CHAN_TO_PAIRIDX(a) ((a - 1) / 2) +#define RF_CHANPAIR(a,b) [CHAN_TO_PAIRIDX(a)] +static const u16 uw2453_std_vco_cfg[][7] = { + { /* table 1 */ + RF_CHANPAIR( 1, 2) = 0x664d, + RF_CHANPAIR( 3, 4) = 0x604d, + RF_CHANPAIR( 5, 6) = 0x6675, + RF_CHANPAIR( 7, 8) = 0x6475, + RF_CHANPAIR( 9, 10) = 0x6655, + RF_CHANPAIR(11, 12) = 0x6455, + RF_CHANPAIR(13, 14) = 0x6665, + }, + { /* table 2 */ + RF_CHANPAIR( 1, 2) = 0x666d, + RF_CHANPAIR( 3, 4) = 0x606d, + RF_CHANPAIR( 5, 6) = 0x664d, + RF_CHANPAIR( 7, 8) = 0x644d, + RF_CHANPAIR( 9, 10) = 0x6675, + RF_CHANPAIR(11, 12) = 0x6475, + RF_CHANPAIR(13, 14) = 0x6655, + }, + { /* table 3 */ + RF_CHANPAIR( 1, 2) = 0x665d, + RF_CHANPAIR( 3, 4) = 0x605d, + RF_CHANPAIR( 5, 6) = 0x666d, + RF_CHANPAIR( 7, 8) = 0x646d, + RF_CHANPAIR( 9, 10) = 0x664d, + RF_CHANPAIR(11, 12) = 0x644d, + RF_CHANPAIR(13, 14) = 0x6675, + }, + { /* table 4 */ + RF_CHANPAIR( 1, 2) = 0x667d, + RF_CHANPAIR( 3, 4) = 0x607d, + RF_CHANPAIR( 5, 6) = 0x665d, + RF_CHANPAIR( 7, 8) = 0x645d, + RF_CHANPAIR( 9, 10) = 0x666d, + RF_CHANPAIR(11, 12) = 0x646d, + RF_CHANPAIR(13, 14) = 0x664d, + }, + { /* table 5 */ + RF_CHANPAIR( 1, 2) = 0x6643, + RF_CHANPAIR( 3, 4) = 0x6043, + RF_CHANPAIR( 5, 6) = 0x667d, + RF_CHANPAIR( 7, 8) = 0x647d, + RF_CHANPAIR( 9, 10) = 0x665d, + RF_CHANPAIR(11, 12) = 0x645d, + RF_CHANPAIR(13, 14) = 0x666d, + }, + { /* table 6 */ + RF_CHANPAIR( 1, 2) = 0x6663, + RF_CHANPAIR( 3, 4) = 0x6063, + RF_CHANPAIR( 5, 6) = 0x6643, + RF_CHANPAIR( 7, 8) = 0x6443, + RF_CHANPAIR( 9, 10) = 0x667d, + RF_CHANPAIR(11, 12) = 0x647d, + RF_CHANPAIR(13, 14) = 0x665d, + }, + { /* table 7 */ + RF_CHANPAIR( 1, 2) = 0x6653, + RF_CHANPAIR( 3, 4) = 0x6053, + RF_CHANPAIR( 5, 6) = 0x6663, + RF_CHANPAIR( 7, 8) = 0x6463, + RF_CHANPAIR( 9, 10) = 0x6643, + RF_CHANPAIR(11, 12) = 0x6443, + RF_CHANPAIR(13, 14) = 0x667d, + }, + { /* table 8 */ + RF_CHANPAIR( 1, 2) = 0x6673, + RF_CHANPAIR( 3, 4) = 0x6073, + RF_CHANPAIR( 5, 6) = 0x6653, + RF_CHANPAIR( 7, 8) = 0x6453, + RF_CHANPAIR( 9, 10) = 0x6663, + RF_CHANPAIR(11, 12) = 0x6463, + RF_CHANPAIR(13, 14) = 0x6643, + }, + { /* table 9 */ + RF_CHANPAIR( 1, 2) = 0x664b, + RF_CHANPAIR( 3, 4) = 0x604b, + RF_CHANPAIR( 5, 6) = 0x6673, + RF_CHANPAIR( 7, 8) = 0x6473, + RF_CHANPAIR( 9, 10) = 0x6653, + RF_CHANPAIR(11, 12) = 0x6453, + RF_CHANPAIR(13, 14) = 0x6663, + }, + { /* table 10 */ + RF_CHANPAIR( 1, 2) = 0x666b, + RF_CHANPAIR( 3, 4) = 0x606b, + RF_CHANPAIR( 5, 6) = 0x664b, + RF_CHANPAIR( 7, 8) = 0x644b, + RF_CHANPAIR( 9, 10) = 0x6673, + RF_CHANPAIR(11, 12) = 0x6473, + RF_CHANPAIR(13, 14) = 0x6653, + }, + { /* table 11 */ + RF_CHANPAIR( 1, 2) = 0x665b, + RF_CHANPAIR( 3, 4) = 0x605b, + RF_CHANPAIR( 5, 6) = 0x666b, + RF_CHANPAIR( 7, 8) = 0x646b, + RF_CHANPAIR( 9, 10) = 0x664b, + RF_CHANPAIR(11, 12) = 0x644b, + RF_CHANPAIR(13, 14) = 0x6673, + }, + +}; + +/* The per-channel synth values for autocal. These get written to register 1. */ +static const u16 uw2453_autocal_synth[] = { + RF_CHANNEL( 1) = 0x6847, + RF_CHANNEL( 2) = 0x6847, + RF_CHANNEL( 3) = 0x6867, + RF_CHANNEL( 4) = 0x6867, + RF_CHANNEL( 5) = 0x6867, + RF_CHANNEL( 6) = 0x6867, + RF_CHANNEL( 7) = 0x6857, + RF_CHANNEL( 8) = 0x6857, + RF_CHANNEL( 9) = 0x6857, + RF_CHANNEL(10) = 0x6857, + RF_CHANNEL(11) = 0x6877, + RF_CHANNEL(12) = 0x6877, + RF_CHANNEL(13) = 0x6877, + RF_CHANNEL(14) = 0x684f, +}; + +/* The VCO configuration for autocal (all channels) */ +static const u16 UW2453_AUTOCAL_VCO_CFG = 0x6662; + +/* TX gain settings. The array index corresponds to the TX power integration + * values found in the EEPROM. The values get written to register 7. */ +static u32 uw2453_txgain[] = { + [0x00] = 0x0e313, + [0x01] = 0x0fb13, + [0x02] = 0x0e093, + [0x03] = 0x0f893, + [0x04] = 0x0ea93, + [0x05] = 0x1f093, + [0x06] = 0x1f493, + [0x07] = 0x1f693, + [0x08] = 0x1f393, + [0x09] = 0x1f35b, + [0x0a] = 0x1e6db, + [0x0b] = 0x1ff3f, + [0x0c] = 0x1ffff, + [0x0d] = 0x361d7, + [0x0e] = 0x37fbf, + [0x0f] = 0x3ff8b, + [0x10] = 0x3ff33, + [0x11] = 0x3fb3f, + [0x12] = 0x3ffff, +}; + +/* RF-specific structure */ +struct uw2453_priv { + /* index into synth/VCO config tables where PLL lock was found + * -1 means autocal */ + int config; +}; + +#define UW2453_PRIV(rf) ((struct uw2453_priv *) (rf)->priv) + +static int uw2453_synth_set_channel(struct zd_chip *chip, int channel, + bool autocal) +{ + int r; + int idx = channel - 1; + u32 val; + + if (autocal) + val = UW2453_REGWRITE(1, uw2453_autocal_synth[idx]); + else + val = UW2453_REGWRITE(1, uw2453_std_synth[idx]); + + r = zd_rfwrite_locked(chip, val, RF_RV_BITS); + if (r) + return r; + + return zd_rfwrite_locked(chip, + UW2453_REGWRITE(2, uw2453_synth_divide[idx]), RF_RV_BITS); +} + +static int uw2453_write_vco_cfg(struct zd_chip *chip, u16 value) +{ + /* vendor driver always sets these upper bits even though the specs say + * they are reserved */ + u32 val = 0x40000 | value; + return zd_rfwrite_locked(chip, UW2453_REGWRITE(3, val), RF_RV_BITS); +} + +static int uw2453_init_mode(struct zd_chip *chip) +{ + static const u32 rv[] = { + UW2453_REGWRITE(0, 0x25f98), /* enter IDLE mode */ + UW2453_REGWRITE(0, 0x25f9a), /* enter CAL_VCO mode */ + UW2453_REGWRITE(0, 0x25f94), /* enter RX/TX mode */ + UW2453_REGWRITE(0, 0x27fd4), /* power down RSSI circuit */ + }; + + return zd_rfwritev_locked(chip, rv, ARRAY_SIZE(rv), RF_RV_BITS); +} + +static int uw2453_set_tx_gain_level(struct zd_chip *chip, int channel) +{ + u8 int_value = chip->pwr_int_values[channel - 1]; + + if (int_value >= ARRAY_SIZE(uw2453_txgain)) { + dev_dbg_f(zd_chip_dev(chip), "can't configure TX gain for " + "int value %x on channel %d\n", int_value, channel); + return 0; + } + + return zd_rfwrite_locked(chip, + UW2453_REGWRITE(7, uw2453_txgain[int_value]), RF_RV_BITS); +} + +static int uw2453_init_hw(struct zd_rf *rf) +{ + int i, r; + int found_config = -1; + u16 intr_status; + struct zd_chip *chip = zd_rf_to_chip(rf); + + static const struct zd_ioreq16 ioreqs[] = { + { CR10, 0x89 }, { CR15, 0x20 }, + { CR17, 0x28 }, /* 6112 no change */ + { CR23, 0x38 }, { CR24, 0x20 }, { CR26, 0x93 }, + { CR27, 0x15 }, { CR28, 0x3e }, { CR29, 0x00 }, + { CR33, 0x28 }, { CR34, 0x30 }, + { CR35, 0x43 }, /* 6112 3e->43 */ + { CR41, 0x24 }, { CR44, 0x32 }, + { CR46, 0x92 }, /* 6112 96->92 */ + { CR47, 0x1e }, + { CR48, 0x04 }, /* 5602 Roger */ + { CR49, 0xfa }, { CR79, 0x58 }, { CR80, 0x30 }, + { CR81, 0x30 }, { CR87, 0x0a }, { CR89, 0x04 }, + { CR91, 0x00 }, { CR92, 0x0a }, { CR98, 0x8d }, + { CR99, 0x28 }, { CR100, 0x02 }, + { CR101, 0x09 }, /* 6112 13->1f 6220 1f->13 6407 13->9 */ + { CR102, 0x27 }, + { CR106, 0x1c }, /* 5d07 5112 1f->1c 6220 1c->1f 6221 1f->1c */ + { CR107, 0x1c }, /* 6220 1c->1a 5221 1a->1c */ + { CR109, 0x13 }, + { CR110, 0x1f }, /* 6112 13->1f 6221 1f->13 6407 13->0x09 */ + { CR111, 0x13 }, { CR112, 0x1f }, { CR113, 0x27 }, + { CR114, 0x23 }, /* 6221 27->23 */ + { CR115, 0x24 }, /* 6112 24->1c 6220 1c->24 */ + { CR116, 0x24 }, /* 6220 1c->24 */ + { CR117, 0xfa }, /* 6112 fa->f8 6220 f8->f4 6220 f4->fa */ + { CR118, 0xf0 }, /* 5d07 6112 f0->f2 6220 f2->f0 */ + { CR119, 0x1a }, /* 6112 1a->10 6220 10->14 6220 14->1a */ + { CR120, 0x4f }, + { CR121, 0x1f }, /* 6220 4f->1f */ + { CR122, 0xf0 }, { CR123, 0x57 }, { CR125, 0xad }, + { CR126, 0x6c }, { CR127, 0x03 }, + { CR128, 0x14 }, /* 6302 12->11 */ + { CR129, 0x12 }, /* 6301 10->0f */ + { CR130, 0x10 }, { CR137, 0x50 }, { CR138, 0xa8 }, + { CR144, 0xac }, { CR146, 0x20 }, { CR252, 0xff }, + { CR253, 0xff }, + }; + + static const u32 rv[] = { + UW2453_REGWRITE(4, 0x2b), /* configure reciever gain */ + UW2453_REGWRITE(5, 0x19e4f), /* configure transmitter gain */ + UW2453_REGWRITE(6, 0xf81ad), /* enable RX/TX filter tuning */ + UW2453_REGWRITE(7, 0x3fffe), /* disable TX gain in test mode */ + + /* enter CAL_FIL mode, TX gain set by registers, RX gain set by pins, + * RSSI circuit powered down, reduced RSSI range */ + UW2453_REGWRITE(0, 0x25f9c), /* 5d01 cal_fil */ + + /* synthesizer configuration for channel 1 */ + UW2453_REGWRITE(1, 0x47), + UW2453_REGWRITE(2, 0x999), + + /* disable manual VCO band selection */ + UW2453_REGWRITE(3, 0x7602), + + /* enable manual VCO band selection, configure current level */ + UW2453_REGWRITE(3, 0x46063), + }; + + r = zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); + if (r) + return r; + + r = zd_rfwritev_locked(chip, rv, ARRAY_SIZE(rv), RF_RV_BITS); + if (r) + return r; + + r = uw2453_init_mode(chip); + if (r) + return r; + + /* Try all standard VCO configuration settings on channel 1 */ + for (i = 0; i < ARRAY_SIZE(uw2453_std_vco_cfg) - 1; i++) { + /* Configure synthesizer for channel 1 */ + r = uw2453_synth_set_channel(chip, 1, false); + if (r) + return r; + + /* Write VCO config */ + r = uw2453_write_vco_cfg(chip, uw2453_std_vco_cfg[i][0]); + if (r) + return r; + + /* ack interrupt event */ + r = zd_iowrite16_locked(chip, 0x0f, UW2453_INTR_REG); + if (r) + return r; + + /* check interrupt status */ + r = zd_ioread16_locked(chip, &intr_status, UW2453_INTR_REG); + if (r) + return r; + + if (!intr_status & 0xf) { + dev_dbg_f(zd_chip_dev(chip), + "PLL locked on configuration %d\n", i); + found_config = i; + break; + } + } + + if (found_config == -1) { + /* autocal */ + dev_dbg_f(zd_chip_dev(chip), + "PLL did not lock, using autocal\n"); + + r = uw2453_synth_set_channel(chip, 1, true); + if (r) + return r; + + r = uw2453_write_vco_cfg(chip, UW2453_AUTOCAL_VCO_CFG); + if (r) + return r; + } + + /* To match the vendor driver behaviour, we use the configuration after + * the one that produced a lock. */ + UW2453_PRIV(rf)->config = found_config + 1; + + return zd_iowrite16_locked(chip, 0x06, CR203); +} + +static int uw2453_set_channel(struct zd_rf *rf, u8 channel) +{ + int r; + u16 vco_cfg; + int config = UW2453_PRIV(rf)->config; + bool autocal = (config == -1); + struct zd_chip *chip = zd_rf_to_chip(rf); + + static const struct zd_ioreq16 ioreqs[] = { + { CR80, 0x30 }, { CR81, 0x30 }, { CR79, 0x58 }, + { CR12, 0xf0 }, { CR77, 0x1b }, { CR78, 0x58 }, + }; + + r = uw2453_synth_set_channel(chip, channel, autocal); + if (r) + return r; + + if (autocal) + vco_cfg = UW2453_AUTOCAL_VCO_CFG; + else + vco_cfg = uw2453_std_vco_cfg[config][CHAN_TO_PAIRIDX(channel)]; + + r = uw2453_write_vco_cfg(chip, vco_cfg); + if (r) + return r; + + r = uw2453_init_mode(chip); + if (r) + return r; + + r = zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); + if (r) + return r; + + r = uw2453_set_tx_gain_level(chip, channel); + if (r) + return r; + + return zd_iowrite16_locked(chip, 0x06, CR203); +} + +static int uw2453_switch_radio_on(struct zd_rf *rf) +{ + int r; + struct zd_chip *chip = zd_rf_to_chip(rf); + struct zd_ioreq16 ioreqs[] = { + { CR11, 0x00 }, { CR251, 0x3f }, + }; + + /* enter RXTX mode */ + r = zd_rfwrite_locked(chip, UW2453_REGWRITE(0, 0x25f94), RF_RV_BITS); + if (r) + return r; + + if (chip->is_zd1211b) + ioreqs[1].value = 0x7f; + + return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); +} + +static int uw2453_switch_radio_off(struct zd_rf *rf) +{ + int r; + struct zd_chip *chip = zd_rf_to_chip(rf); + static const struct zd_ioreq16 ioreqs[] = { + { CR11, 0x04 }, { CR251, 0x2f }, + }; + + /* enter IDLE mode */ + /* FIXME: shouldn't we go to SLEEP? sent email to zydas */ + r = zd_rfwrite_locked(chip, UW2453_REGWRITE(0, 0x25f90), RF_RV_BITS); + if (r) + return r; + + return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); +} + +static void uw2453_clear(struct zd_rf *rf) +{ + kfree(rf->priv); +} + +int zd_rf_init_uw2453(struct zd_rf *rf) +{ + rf->init_hw = uw2453_init_hw; + rf->set_channel = uw2453_set_channel; + rf->switch_radio_on = uw2453_switch_radio_on; + rf->switch_radio_off = uw2453_switch_radio_off; + rf->patch_6m_band_edge = zd_rf_generic_patch_6m; + rf->clear = uw2453_clear; + /* we have our own TX integration code */ + rf->update_channel_int = 0; + + rf->priv = kmalloc(sizeof(struct uw2453_priv), GFP_KERNEL); + if (rf->priv == NULL) + return -ENOMEM; + + return 0; +} + diff --git a/drivers/net/wireless/zd1211rw/zd_usb.c b/drivers/net/wireless/zd1211rw/zd_usb.c index 8459549d0ce..740a2194fdd 100644 --- a/drivers/net/wireless/zd1211rw/zd_usb.c +++ b/drivers/net/wireless/zd1211rw/zd_usb.c @@ -54,6 +54,7 @@ static struct usb_device_id usb_ids[] = { { USB_DEVICE(0x0586, 0x3401), .driver_info = DEVICE_ZD1211 }, { USB_DEVICE(0x14ea, 0xab13), .driver_info = DEVICE_ZD1211 }, { USB_DEVICE(0x13b1, 0x001e), .driver_info = DEVICE_ZD1211 }, + { USB_DEVICE(0x0586, 0x3407), .driver_info = DEVICE_ZD1211 }, /* ZD1211B */ { USB_DEVICE(0x0ace, 0x1215), .driver_info = DEVICE_ZD1211B }, { USB_DEVICE(0x157e, 0x300d), .driver_info = DEVICE_ZD1211B }, |