diff options
Diffstat (limited to 'drivers/net')
-rw-r--r-- | drivers/net/e1000e/defines.h | 10 | ||||
-rw-r--r-- | drivers/net/e1000e/e1000.h | 7 | ||||
-rw-r--r-- | drivers/net/e1000e/ethtool.c | 39 | ||||
-rw-r--r-- | drivers/net/e1000e/hw.h | 22 | ||||
-rw-r--r-- | drivers/net/e1000e/ich8lan.c | 83 | ||||
-rw-r--r-- | drivers/net/e1000e/netdev.c | 330 | ||||
-rw-r--r-- | drivers/net/e1000e/phy.c | 278 |
7 files changed, 748 insertions, 21 deletions
diff --git a/drivers/net/e1000e/defines.h b/drivers/net/e1000e/defines.h index 2a53875cddb..f823b8ba578 100644 --- a/drivers/net/e1000e/defines.h +++ b/drivers/net/e1000e/defines.h @@ -648,6 +648,8 @@ #define IFE_E_PHY_ID 0x02A80330 #define IFE_PLUS_E_PHY_ID 0x02A80320 #define IFE_C_E_PHY_ID 0x02A80310 +#define BME1000_E_PHY_ID 0x01410CB0 +#define BME1000_E_PHY_ID_R2 0x01410CB1 /* M88E1000 Specific Registers */ #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */ @@ -701,6 +703,14 @@ #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800 +/* BME1000 PHY Specific Control Register */ +#define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */ + + +#define PHY_PAGE_SHIFT 5 +#define PHY_REG(page, reg) (((page) << PHY_PAGE_SHIFT) | \ + ((reg) & MAX_PHY_REG_ADDRESS)) + /* * Bits... * 15-5: page diff --git a/drivers/net/e1000e/e1000.h b/drivers/net/e1000e/e1000.h index 38bfd0d261f..d3bc6f8101f 100644 --- a/drivers/net/e1000e/e1000.h +++ b/drivers/net/e1000e/e1000.h @@ -127,7 +127,7 @@ struct e1000_buffer { /* arrays of page information for packet split */ struct e1000_ps_page *ps_pages; }; - + struct page *page; }; struct e1000_ring { @@ -304,6 +304,7 @@ struct e1000_info { #define FLAG_HAS_CTRLEXT_ON_LOAD (1 << 5) #define FLAG_HAS_SWSM_ON_LOAD (1 << 6) #define FLAG_HAS_JUMBO_FRAMES (1 << 7) +#define FLAG_IS_ICH (1 << 9) #define FLAG_HAS_SMART_POWER_DOWN (1 << 11) #define FLAG_IS_QUAD_PORT_A (1 << 12) #define FLAG_IS_QUAD_PORT (1 << 13) @@ -386,6 +387,7 @@ extern void e1000e_set_kmrn_lock_loss_workaround_ich8lan(struct e1000_hw *hw, bool state); extern void e1000e_igp3_phy_powerdown_workaround_ich8lan(struct e1000_hw *hw); extern void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw); +extern void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw); extern s32 e1000e_check_for_copper_link(struct e1000_hw *hw); extern s32 e1000e_check_for_fiber_link(struct e1000_hw *hw); @@ -443,6 +445,9 @@ extern s32 e1000e_get_phy_info_m88(struct e1000_hw *hw); extern s32 e1000e_read_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 *data); extern s32 e1000e_write_phy_reg_m88(struct e1000_hw *hw, u32 offset, u16 data); extern enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id); +extern s32 e1000e_determine_phy_address(struct e1000_hw *hw); +extern s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data); +extern s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data); extern void e1000e_phy_force_speed_duplex_setup(struct e1000_hw *hw, u16 *phy_ctrl); extern s32 e1000e_write_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 data); extern s32 e1000e_read_kmrn_reg(struct e1000_hw *hw, u32 offset, u16 *data); diff --git a/drivers/net/e1000e/ethtool.c b/drivers/net/e1000e/ethtool.c index ce045acce63..2bb6da057c4 100644 --- a/drivers/net/e1000e/ethtool.c +++ b/drivers/net/e1000e/ethtool.c @@ -803,8 +803,7 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data) /* restore previous status */ ew32(STATUS, before); - if ((mac->type != e1000_ich8lan) && - (mac->type != e1000_ich9lan)) { + if (!(adapter->flags & FLAG_IS_ICH)) { REG_PATTERN_TEST(E1000_FCAL, 0xFFFFFFFF, 0xFFFFFFFF); REG_PATTERN_TEST(E1000_FCAH, 0x0000FFFF, 0xFFFFFFFF); REG_PATTERN_TEST(E1000_FCT, 0x0000FFFF, 0xFFFFFFFF); @@ -824,15 +823,13 @@ static int e1000_reg_test(struct e1000_adapter *adapter, u64 *data) REG_SET_AND_CHECK(E1000_RCTL, 0xFFFFFFFF, 0x00000000); - before = (((mac->type == e1000_ich8lan) || - (mac->type == e1000_ich9lan)) ? 0x06C3B33E : 0x06DFB3FE); + before = ((adapter->flags & FLAG_IS_ICH) ? 0x06C3B33E : 0x06DFB3FE); REG_SET_AND_CHECK(E1000_RCTL, before, 0x003FFFFB); REG_SET_AND_CHECK(E1000_TCTL, 0xFFFFFFFF, 0x00000000); REG_SET_AND_CHECK(E1000_RCTL, before, 0xFFFFFFFF); REG_PATTERN_TEST(E1000_RDBAL, 0xFFFFFFF0, 0xFFFFFFFF); - if ((mac->type != e1000_ich8lan) && - (mac->type != e1000_ich9lan)) + if (!(adapter->flags & FLAG_IS_ICH)) REG_PATTERN_TEST(E1000_TXCW, 0xC000FFFF, 0x0000FFFF); REG_PATTERN_TEST(E1000_TDBAL, 0xFFFFFFF0, 0xFFFFFFFF); REG_PATTERN_TEST(E1000_TIDV, 0x0000FFFF, 0x0000FFFF); @@ -911,9 +908,7 @@ static int e1000_intr_test(struct e1000_adapter *adapter, u64 *data) /* Test each interrupt */ for (i = 0; i < 10; i++) { - - if (((adapter->hw.mac.type == e1000_ich8lan) || - (adapter->hw.mac.type == e1000_ich9lan)) && i == 8) + if ((adapter->flags & FLAG_IS_ICH) && (i == 8)) continue; /* Interrupt to test */ @@ -1184,6 +1179,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter) struct e1000_hw *hw = &adapter->hw; u32 ctrl_reg = 0; u32 stat_reg = 0; + u16 phy_reg = 0; hw->mac.autoneg = 0; @@ -1211,6 +1207,28 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter) E1000_CTRL_SPD_100 |/* Force Speed to 100 */ E1000_CTRL_FD); /* Force Duplex to FULL */ break; + case e1000_phy_bm: + /* Set Default MAC Interface speed to 1GB */ + e1e_rphy(hw, PHY_REG(2, 21), &phy_reg); + phy_reg &= ~0x0007; + phy_reg |= 0x006; + e1e_wphy(hw, PHY_REG(2, 21), phy_reg); + /* Assert SW reset for above settings to take effect */ + e1000e_commit_phy(hw); + mdelay(1); + /* Force Full Duplex */ + e1e_rphy(hw, PHY_REG(769, 16), &phy_reg); + e1e_wphy(hw, PHY_REG(769, 16), phy_reg | 0x000C); + /* Set Link Up (in force link) */ + e1e_rphy(hw, PHY_REG(776, 16), &phy_reg); + e1e_wphy(hw, PHY_REG(776, 16), phy_reg | 0x0040); + /* Force Link */ + e1e_rphy(hw, PHY_REG(769, 16), &phy_reg); + e1e_wphy(hw, PHY_REG(769, 16), phy_reg | 0x0040); + /* Set Early Link Enable */ + e1e_rphy(hw, PHY_REG(769, 20), &phy_reg); + e1e_wphy(hw, PHY_REG(769, 20), phy_reg | 0x0400); + /* fall through */ default: /* force 1000, set loopback */ e1e_wphy(hw, PHY_CONTROL, 0x4140); @@ -1224,8 +1242,7 @@ static int e1000_integrated_phy_loopback(struct e1000_adapter *adapter) E1000_CTRL_SPD_1000 |/* Force Speed to 1000 */ E1000_CTRL_FD); /* Force Duplex to FULL */ - if ((adapter->hw.mac.type == e1000_ich8lan) || - (adapter->hw.mac.type == e1000_ich9lan)) + if (adapter->flags & FLAG_IS_ICH) ctrl_reg |= E1000_CTRL_SLU; /* Set Link Up */ } diff --git a/drivers/net/e1000e/hw.h b/drivers/net/e1000e/hw.h index a930e6d9cf0..74f263acb17 100644 --- a/drivers/net/e1000e/hw.h +++ b/drivers/net/e1000e/hw.h @@ -216,6 +216,21 @@ enum e1e_registers { #define IGP01E1000_PHY_LINK_HEALTH 0x13 /* PHY Link Health */ #define IGP02E1000_PHY_POWER_MGMT 0x19 /* Power Management */ #define IGP01E1000_PHY_PAGE_SELECT 0x1F /* Page Select */ +#define BM_PHY_PAGE_SELECT 22 /* Page Select for BM */ +#define IGP_PAGE_SHIFT 5 +#define PHY_REG_MASK 0x1F + +#define BM_WUC_PAGE 800 +#define BM_WUC_ADDRESS_OPCODE 0x11 +#define BM_WUC_DATA_OPCODE 0x12 +#define BM_WUC_ENABLE_PAGE 769 +#define BM_WUC_ENABLE_REG 17 +#define BM_WUC_ENABLE_BIT (1 << 2) +#define BM_WUC_HOST_WU_BIT (1 << 4) + +#define BM_WUC PHY_REG(BM_WUC_PAGE, 1) +#define BM_WUFC PHY_REG(BM_WUC_PAGE, 2) +#define BM_WUS PHY_REG(BM_WUC_PAGE, 3) #define IGP01E1000_PHY_PCS_INIT_REG 0x00B4 #define IGP01E1000_PHY_POLARITY_MASK 0x0078 @@ -331,10 +346,16 @@ enum e1e_registers { #define E1000_DEV_ID_ICH8_IFE_G 0x10C5 #define E1000_DEV_ID_ICH8_IGP_M 0x104D #define E1000_DEV_ID_ICH9_IGP_AMT 0x10BD +#define E1000_DEV_ID_ICH9_IGP_M_AMT 0x10F5 +#define E1000_DEV_ID_ICH9_IGP_M 0x10BF +#define E1000_DEV_ID_ICH9_IGP_M_V 0x10CB #define E1000_DEV_ID_ICH9_IGP_C 0x294C #define E1000_DEV_ID_ICH9_IFE 0x10C0 #define E1000_DEV_ID_ICH9_IFE_GT 0x10C3 #define E1000_DEV_ID_ICH9_IFE_G 0x10C2 +#define E1000_DEV_ID_ICH10_R_BM_LM 0x10CC +#define E1000_DEV_ID_ICH10_R_BM_LF 0x10CD +#define E1000_DEV_ID_ICH10_R_BM_V 0x10CE #define E1000_FUNC_1 1 @@ -378,6 +399,7 @@ enum e1000_phy_type { e1000_phy_gg82563, e1000_phy_igp_3, e1000_phy_ife, + e1000_phy_bm, }; enum e1000_bus_width { diff --git a/drivers/net/e1000e/ich8lan.c b/drivers/net/e1000e/ich8lan.c index 768485dbb2c..9e38452a738 100644 --- a/drivers/net/e1000e/ich8lan.c +++ b/drivers/net/e1000e/ich8lan.c @@ -38,6 +38,12 @@ * 82566DM Gigabit Network Connection * 82566MC Gigabit Network Connection * 82566MM Gigabit Network Connection + * 82567LM Gigabit Network Connection + * 82567LF Gigabit Network Connection + * 82567LM-2 Gigabit Network Connection + * 82567LF-2 Gigabit Network Connection + * 82567V-2 Gigabit Network Connection + * 82562GT-3 10/100 Network Connection */ #include <linux/netdevice.h> @@ -198,6 +204,19 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) phy->addr = 1; phy->reset_delay_us = 100; + /* + * We may need to do this twice - once for IGP and if that fails, + * we'll set BM func pointers and try again + */ + ret_val = e1000e_determine_phy_address(hw); + if (ret_val) { + hw->phy.ops.write_phy_reg = e1000e_write_phy_reg_bm; + hw->phy.ops.read_phy_reg = e1000e_read_phy_reg_bm; + ret_val = e1000e_determine_phy_address(hw); + if (ret_val) + return ret_val; + } + phy->id = 0; while ((e1000_phy_unknown == e1000e_get_phy_type_from_id(phy->id)) && (i++ < 100)) { @@ -219,6 +238,13 @@ static s32 e1000_init_phy_params_ich8lan(struct e1000_hw *hw) phy->type = e1000_phy_ife; phy->autoneg_mask = E1000_ALL_NOT_GIG; break; + case BME1000_E_PHY_ID: + phy->type = e1000_phy_bm; + phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT; + hw->phy.ops.read_phy_reg = e1000e_read_phy_reg_bm; + hw->phy.ops.write_phy_reg = e1000e_write_phy_reg_bm; + hw->phy.ops.commit_phy = e1000e_phy_sw_reset; + break; default: return -E1000_ERR_PHY; break; @@ -664,6 +690,7 @@ static s32 e1000_get_phy_info_ich8lan(struct e1000_hw *hw) return e1000_get_phy_info_ife_ich8lan(hw); break; case e1000_phy_igp_3: + case e1000_phy_bm: return e1000e_get_phy_info_igp(hw); break; default: @@ -728,7 +755,7 @@ static s32 e1000_set_d0_lplu_state_ich8lan(struct e1000_hw *hw, bool active) s32 ret_val = 0; u16 data; - if (phy->type != e1000_phy_igp_3) + if (phy->type == e1000_phy_ife) return ret_val; phy_ctrl = er32(PHY_CTRL); @@ -1918,8 +1945,35 @@ static s32 e1000_setup_copper_link_ich8lan(struct e1000_hw *hw) ret_val = e1000e_copper_link_setup_igp(hw); if (ret_val) return ret_val; + } else if (hw->phy.type == e1000_phy_bm) { + ret_val = e1000e_copper_link_setup_m88(hw); + if (ret_val) + return ret_val; } + if (hw->phy.type == e1000_phy_ife) { + ret_val = e1e_rphy(hw, IFE_PHY_MDIX_CONTROL, ®_data); + if (ret_val) + return ret_val; + + reg_data &= ~IFE_PMC_AUTO_MDIX; + + switch (hw->phy.mdix) { + case 1: + reg_data &= ~IFE_PMC_FORCE_MDIX; + break; + case 2: + reg_data |= IFE_PMC_FORCE_MDIX; + break; + case 0: + default: + reg_data |= IFE_PMC_AUTO_MDIX; + break; + } + ret_val = e1e_wphy(hw, IFE_PHY_MDIX_CONTROL, reg_data); + if (ret_val) + return ret_val; + } return e1000e_setup_copper_link(hw); } @@ -2127,6 +2181,31 @@ void e1000e_gig_downshift_workaround_ich8lan(struct e1000_hw *hw) } /** + * e1000e_disable_gig_wol_ich8lan - disable gig during WoL + * @hw: pointer to the HW structure + * + * During S0 to Sx transition, it is possible the link remains at gig + * instead of negotiating to a lower speed. Before going to Sx, set + * 'LPLU Enabled' and 'Gig Disable' to force link speed negotiation + * to a lower speed. + * + * Should only be called for ICH9 devices. + **/ +void e1000e_disable_gig_wol_ich8lan(struct e1000_hw *hw) +{ + u32 phy_ctrl; + + if (hw->mac.type == e1000_ich9lan) { + phy_ctrl = er32(PHY_CTRL); + phy_ctrl |= E1000_PHY_CTRL_D0A_LPLU | + E1000_PHY_CTRL_GBE_DISABLE; + ew32(PHY_CTRL, phy_ctrl); + } + + return; +} + +/** * e1000_cleanup_led_ich8lan - Restore the default LED operation * @hw: pointer to the HW structure * @@ -2247,6 +2326,7 @@ static struct e1000_nvm_operations ich8_nvm_ops = { struct e1000_info e1000_ich8_info = { .mac = e1000_ich8lan, .flags = FLAG_HAS_WOL + | FLAG_IS_ICH | FLAG_RX_CSUM_ENABLED | FLAG_HAS_CTRLEXT_ON_LOAD | FLAG_HAS_AMT @@ -2262,6 +2342,7 @@ struct e1000_info e1000_ich8_info = { struct e1000_info e1000_ich9_info = { .mac = e1000_ich9lan, .flags = FLAG_HAS_JUMBO_FRAMES + | FLAG_IS_ICH | FLAG_HAS_WOL | FLAG_RX_CSUM_ENABLED | FLAG_HAS_CTRLEXT_ON_LOAD diff --git a/drivers/net/e1000e/netdev.c b/drivers/net/e1000e/netdev.c index 8991ab8911e..8cbb40f3a50 100644 --- a/drivers/net/e1000e/netdev.c +++ b/drivers/net/e1000e/netdev.c @@ -43,10 +43,11 @@ #include <linux/if_vlan.h> #include <linux/cpu.h> #include <linux/smp.h> +#include <linux/pm_qos_params.h> #include "e1000.h" -#define DRV_VERSION "0.2.1" +#define DRV_VERSION "0.3.3.3-k2" char e1000e_driver_name[] = "e1000e"; const char e1000e_driver_version[] = DRV_VERSION; @@ -341,6 +342,89 @@ no_buffers: } /** + * e1000_alloc_jumbo_rx_buffers - Replace used jumbo receive buffers + * @adapter: address of board private structure + * @rx_ring: pointer to receive ring structure + * @cleaned_count: number of buffers to allocate this pass + **/ + +static void e1000_alloc_jumbo_rx_buffers(struct e1000_adapter *adapter, + int cleaned_count) +{ + struct net_device *netdev = adapter->netdev; + struct pci_dev *pdev = adapter->pdev; + struct e1000_rx_desc *rx_desc; + struct e1000_ring *rx_ring = adapter->rx_ring; + struct e1000_buffer *buffer_info; + struct sk_buff *skb; + unsigned int i; + unsigned int bufsz = 256 - + 16 /* for skb_reserve */ - + NET_IP_ALIGN; + + i = rx_ring->next_to_use; + buffer_info = &rx_ring->buffer_info[i]; + + while (cleaned_count--) { + skb = buffer_info->skb; + if (skb) { + skb_trim(skb, 0); + goto check_page; + } + + skb = netdev_alloc_skb(netdev, bufsz); + if (unlikely(!skb)) { + /* Better luck next round */ + adapter->alloc_rx_buff_failed++; + break; + } + + /* Make buffer alignment 2 beyond a 16 byte boundary + * this will result in a 16 byte aligned IP header after + * the 14 byte MAC header is removed + */ + skb_reserve(skb, NET_IP_ALIGN); + + buffer_info->skb = skb; +check_page: + /* allocate a new page if necessary */ + if (!buffer_info->page) { + buffer_info->page = alloc_page(GFP_ATOMIC); + if (unlikely(!buffer_info->page)) { + adapter->alloc_rx_buff_failed++; + break; + } + } + + if (!buffer_info->dma) + buffer_info->dma = pci_map_page(pdev, + buffer_info->page, 0, + PAGE_SIZE, + PCI_DMA_FROMDEVICE); + + rx_desc = E1000_RX_DESC(*rx_ring, i); + rx_desc->buffer_addr = cpu_to_le64(buffer_info->dma); + + if (unlikely(++i == rx_ring->count)) + i = 0; + buffer_info = &rx_ring->buffer_info[i]; + } + + if (likely(rx_ring->next_to_use != i)) { + rx_ring->next_to_use = i; + if (unlikely(i-- == 0)) + i = (rx_ring->count - 1); + + /* Force memory writes to complete before letting h/w + * know there are new descriptors to fetch. (Only + * applicable for weak-ordered memory model archs, + * such as IA-64). */ + wmb(); + writel(i, adapter->hw.hw_addr + rx_ring->tail); + } +} + +/** * e1000_clean_rx_irq - Send received data up the network stack; legacy * @adapter: board private structure * @@ -783,6 +867,186 @@ next_desc: } /** + * e1000_consume_page - helper function + **/ +static void e1000_consume_page(struct e1000_buffer *bi, struct sk_buff *skb, + u16 length) +{ + bi->page = NULL; + skb->len += length; + skb->data_len += length; + skb->truesize += length; +} + +/** + * e1000_clean_jumbo_rx_irq - Send received data up the network stack; legacy + * @adapter: board private structure + * + * the return value indicates whether actual cleaning was done, there + * is no guarantee that everything was cleaned + **/ + +static bool e1000_clean_jumbo_rx_irq(struct e1000_adapter *adapter, + int *work_done, int work_to_do) +{ + struct net_device *netdev = adapter->netdev; + struct pci_dev *pdev = adapter->pdev; + struct e1000_ring *rx_ring = adapter->rx_ring; + struct e1000_rx_desc *rx_desc, *next_rxd; + struct e1000_buffer *buffer_info, *next_buffer; + u32 length; + unsigned int i; + int cleaned_count = 0; + bool cleaned = false; + unsigned int total_rx_bytes=0, total_rx_packets=0; + + i = rx_ring->next_to_clean; + rx_desc = E1000_RX_DESC(*rx_ring, i); + buffer_info = &rx_ring->buffer_info[i]; + + while (rx_desc->status & E1000_RXD_STAT_DD) { + struct sk_buff *skb; + u8 status; + + if (*work_done >= work_to_do) + break; + (*work_done)++; + + status = rx_desc->status; + skb = buffer_info->skb; + buffer_info->skb = NULL; + + ++i; + if (i == rx_ring->count) + i = 0; + next_rxd = E1000_RX_DESC(*rx_ring, i); + prefetch(next_rxd); + + next_buffer = &rx_ring->buffer_info[i]; + + cleaned = true; + cleaned_count++; + pci_unmap_page(pdev, buffer_info->dma, PAGE_SIZE, + PCI_DMA_FROMDEVICE); + buffer_info->dma = 0; + + length = le16_to_cpu(rx_desc->length); + + /* errors is only valid for DD + EOP descriptors */ + if (unlikely((status & E1000_RXD_STAT_EOP) && + (rx_desc->errors & E1000_RXD_ERR_FRAME_ERR_MASK))) { + /* recycle both page and skb */ + buffer_info->skb = skb; + /* an error means any chain goes out the window + * too */ + if (rx_ring->rx_skb_top) + dev_kfree_skb(rx_ring->rx_skb_top); + rx_ring->rx_skb_top = NULL; + goto next_desc; + } + +#define rxtop rx_ring->rx_skb_top + if (!(status & E1000_RXD_STAT_EOP)) { + /* this descriptor is only the beginning (or middle) */ + if (!rxtop) { + /* this is the beginning of a chain */ + rxtop = skb; + skb_fill_page_desc(rxtop, 0, buffer_info->page, + 0, length); + } else { + /* this is the middle of a chain */ + skb_fill_page_desc(rxtop, + skb_shinfo(rxtop)->nr_frags, + buffer_info->page, 0, length); + /* re-use the skb, only consumed the page */ + buffer_info->skb = skb; + } + e1000_consume_page(buffer_info, rxtop, length); + goto next_desc; + } else { + if (rxtop) { + /* end of the chain */ + skb_fill_page_desc(rxtop, + skb_shinfo(rxtop)->nr_frags, + buffer_info->page, 0, length); + /* re-use the current skb, we only consumed the + * page */ + buffer_info->skb = skb; + skb = rxtop; + rxtop = NULL; + e1000_consume_page(buffer_info, skb, length); + } else { + /* no chain, got EOP, this buf is the packet + * copybreak to save the put_page/alloc_page */ + if (length <= copybreak && + skb_tailroom(skb) >= length) { + u8 *vaddr; + vaddr = kmap_atomic(buffer_info->page, + KM_SKB_DATA_SOFTIRQ); + memcpy(skb_tail_pointer(skb), vaddr, + length); + kunmap_atomic(vaddr, + KM_SKB_DATA_SOFTIRQ); + /* re-use the page, so don't erase + * buffer_info->page */ + skb_put(skb, length); + } else { + skb_fill_page_desc(skb, 0, + buffer_info->page, 0, + length); + e1000_consume_page(buffer_info, skb, + length); + } + } + } + + /* Receive Checksum Offload XXX recompute due to CRC strip? */ + e1000_rx_checksum(adapter, + (u32)(status) | + ((u32)(rx_desc->errors) << 24), + le16_to_cpu(rx_desc->csum), skb); + + /* probably a little skewed due to removing CRC */ + total_rx_bytes += skb->len; + total_rx_packets++; + + /* eth type trans needs skb->data to point to something */ + if (!pskb_may_pull(skb, ETH_HLEN)) { + ndev_err(netdev, "pskb_may_pull failed.\n"); + dev_kfree_skb(skb); + goto next_desc; + } + + e1000_receive_skb(adapter, netdev, skb, status, + rx_desc->special); + +next_desc: + rx_desc->status = 0; + + /* return some buffers to hardware, one at a time is too slow */ + if (unlikely(cleaned_count >= E1000_RX_BUFFER_WRITE)) { + adapter->alloc_rx_buf(adapter, cleaned_count); + cleaned_count = 0; + } + + /* use prefetched values */ + rx_desc = next_rxd; + buffer_info = next_buffer; + } + rx_ring->next_to_clean = i; + + cleaned_count = e1000_desc_unused(rx_ring); + if (cleaned_count) + adapter->alloc_rx_buf(adapter, cleaned_count); + + adapter->total_rx_bytes += total_rx_bytes; + adapter->total_rx_packets += total_rx_packets; + adapter->net_stats.rx_bytes += total_rx_bytes; + adapter->net_stats.rx_packets += total_rx_packets; + return cleaned; +} + +/** * e1000_clean_rx_ring - Free Rx Buffers per Queue * @adapter: board private structure **/ @@ -802,6 +1066,10 @@ static void e1000_clean_rx_ring(struct e1000_adapter *adapter) pci_unmap_single(pdev, buffer_info->dma, adapter->rx_buffer_len, PCI_DMA_FROMDEVICE); + else if (adapter->clean_rx == e1000_clean_jumbo_rx_irq) + pci_unmap_page(pdev, buffer_info->dma, + PAGE_SIZE, + PCI_DMA_FROMDEVICE); else if (adapter->clean_rx == e1000_clean_rx_irq_ps) pci_unmap_single(pdev, buffer_info->dma, adapter->rx_ps_bsize0, @@ -809,6 +1077,11 @@ static void e1000_clean_rx_ring(struct e1000_adapter *adapter) buffer_info->dma = 0; } + if (buffer_info->page) { + put_page(buffer_info->page); + buffer_info->page = NULL; + } + if (buffer_info->skb) { dev_kfree_skb(buffer_info->skb); buffer_info->skb = NULL; @@ -1755,10 +2028,12 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter) * a lot of memory, since we allocate 3 pages at all times * per packet. */ - adapter->rx_ps_pages = 0; pages = PAGE_USE_COUNT(adapter->netdev->mtu); - if ((pages <= 3) && (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE)) + if (!(adapter->flags & FLAG_IS_ICH) && (pages <= 3) && + (PAGE_SIZE <= 16384) && (rctl & E1000_RCTL_LPE)) adapter->rx_ps_pages = pages; + else + adapter->rx_ps_pages = 0; if (adapter->rx_ps_pages) { /* Configure extra packet-split registers */ @@ -1819,9 +2094,12 @@ static void e1000_configure_rx(struct e1000_adapter *adapter) sizeof(union e1000_rx_desc_packet_split); adapter->clean_rx = e1000_clean_rx_irq_ps; adapter->alloc_rx_buf = e1000_alloc_rx_buffers_ps; + } else if (adapter->netdev->mtu > ETH_FRAME_LEN + ETH_FCS_LEN) { + rdlen = rx_ring->count * sizeof(struct e1000_rx_desc); + adapter->clean_rx = e1000_clean_jumbo_rx_irq; + adapter->alloc_rx_buf = e1000_alloc_jumbo_rx_buffers; } else { - rdlen = rx_ring->count * - sizeof(struct e1000_rx_desc); + rdlen = rx_ring->count * sizeof(struct e1000_rx_desc); adapter->clean_rx = e1000_clean_rx_irq; adapter->alloc_rx_buf = e1000_alloc_rx_buffers; } @@ -1885,8 +2163,21 @@ static void e1000_configure_rx(struct e1000_adapter *adapter) * units), e.g. using jumbo frames when setting to E1000_ERT_2048 */ if ((adapter->flags & FLAG_HAS_ERT) && - (adapter->netdev->mtu > ETH_DATA_LEN)) - ew32(ERT, E1000_ERT_2048); + (adapter->netdev->mtu > ETH_DATA_LEN)) { + u32 rxdctl = er32(RXDCTL(0)); + ew32(RXDCTL(0), rxdctl | 0x3); + ew32(ERT, E1000_ERT_2048 | (1 << 13)); + /* + * With jumbo frames and early-receive enabled, excessive + * C4->C2 latencies result in dropped transactions. + */ + pm_qos_update_requirement(PM_QOS_CPU_DMA_LATENCY, + e1000e_driver_name, 55); + } else { + pm_qos_update_requirement(PM_QOS_CPU_DMA_LATENCY, + e1000e_driver_name, + PM_QOS_DEFAULT_VALUE); + } /* Enable Receives */ ew32(RCTL, rctl); @@ -2155,6 +2446,14 @@ void e1000e_reset(struct e1000_adapter *adapter) /* Allow time for pending master requests to run */ mac->ops.reset_hw(hw); + + /* + * For parts with AMT enabled, let the firmware know + * that the network interface is in control + */ + if ((adapter->flags & FLAG_HAS_AMT) && e1000e_check_mng_mode(hw)) + e1000_get_hw_control(adapter); + ew32(WUC, 0); if (mac->ops.init_hw(hw)) @@ -3469,6 +3768,8 @@ static int e1000_change_mtu(struct net_device *netdev, int new_mtu) * means we reserve 2 more, this pushes us to allocate from the next * larger slab size. * i.e. RXBUFFER_2048 --> size-4096 slab + * However with the new *_jumbo_rx* routines, jumbo receives will use + * fragmented skbs */ if (max_frame <= 256) @@ -3626,6 +3927,9 @@ static int e1000_suspend(struct pci_dev *pdev, pm_message_t state) ew32(CTRL_EXT, ctrl_ext); } + if (adapter->flags & FLAG_IS_ICH) + e1000e_disable_gig_wol_ich8lan(&adapter->hw); + /* Allow time for pending master requests to run */ e1000e_disable_pcie_master(&adapter->hw); @@ -4292,6 +4596,13 @@ static struct pci_device_id e1000_pci_tbl[] = { { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IFE_GT), board_ich9lan }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_AMT), board_ich9lan }, { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_C), board_ich9lan }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M), board_ich9lan }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_AMT), board_ich9lan }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH9_IGP_M_V), board_ich9lan }, + + { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LM), board_ich9lan }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_LF), board_ich9lan }, + { PCI_VDEVICE(INTEL, E1000_DEV_ID_ICH10_R_BM_V), board_ich9lan }, { } /* terminate list */ }; @@ -4326,7 +4637,9 @@ static int __init e1000_init_module(void) printk(KERN_INFO "%s: Copyright (c) 1999-2008 Intel Corporation.\n", e1000e_driver_name); ret = pci_register_driver(&e1000_driver); - + pm_qos_add_requirement(PM_QOS_CPU_DMA_LATENCY, e1000e_driver_name, + PM_QOS_DEFAULT_VALUE); + return ret; } module_init(e1000_init_module); @@ -4340,6 +4653,7 @@ module_init(e1000_init_module); static void __exit e1000_exit_module(void) { pci_unregister_driver(&e1000_driver); + pm_qos_remove_requirement(PM_QOS_CPU_DMA_LATENCY, e1000e_driver_name); } module_exit(e1000_exit_module); diff --git a/drivers/net/e1000e/phy.c b/drivers/net/e1000e/phy.c index e102332a6be..b133dcf0e95 100644 --- a/drivers/net/e1000e/phy.c +++ b/drivers/net/e1000e/phy.c @@ -34,6 +34,9 @@ static s32 e1000_get_phy_cfg_done(struct e1000_hw *hw); static s32 e1000_phy_force_speed_duplex(struct e1000_hw *hw); static s32 e1000_set_d0_lplu_state(struct e1000_hw *hw, bool active); static s32 e1000_wait_autoneg(struct e1000_hw *hw); +static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg); +static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset, + u16 *data, bool read); /* Cable length tables */ static const u16 e1000_m88_cable_length_table[] = @@ -465,6 +468,10 @@ s32 e1000e_copper_link_setup_m88(struct e1000_hw *hw) if (phy->disable_polarity_correction == 1) phy_data |= M88E1000_PSCR_POLARITY_REVERSAL; + /* Enable downshift on BM (disabled by default) */ + if (phy->type == e1000_phy_bm) + phy_data |= BME1000_PSCR_ENABLE_DOWNSHIFT; + ret_val = e1e_wphy(hw, M88E1000_PHY_SPEC_CTRL, phy_data); if (ret_val) return ret_val; @@ -1776,6 +1783,10 @@ enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id) case IFE_C_E_PHY_ID: phy_type = e1000_phy_ife; break; + case BME1000_E_PHY_ID: + case BME1000_E_PHY_ID_R2: + phy_type = e1000_phy_bm; + break; default: phy_type = e1000_phy_unknown; break; @@ -1784,6 +1795,273 @@ enum e1000_phy_type e1000e_get_phy_type_from_id(u32 phy_id) } /** + * e1000e_determine_phy_address - Determines PHY address. + * @hw: pointer to the HW structure + * + * This uses a trial and error method to loop through possible PHY + * addresses. It tests each by reading the PHY ID registers and + * checking for a match. + **/ +s32 e1000e_determine_phy_address(struct e1000_hw *hw) +{ + s32 ret_val = -E1000_ERR_PHY_TYPE; + u32 phy_addr= 0; + u32 i = 0; + enum e1000_phy_type phy_type = e1000_phy_unknown; + + do { + for (phy_addr = 0; phy_addr < 4; phy_addr++) { + hw->phy.addr = phy_addr; + e1000e_get_phy_id(hw); + phy_type = e1000e_get_phy_type_from_id(hw->phy.id); + + /* + * If phy_type is valid, break - we found our + * PHY address + */ + if (phy_type != e1000_phy_unknown) { + ret_val = 0; + break; + } + } + i++; + } while ((ret_val != 0) && (i < 100)); + + return ret_val; +} + +/** + * e1000_get_phy_addr_for_bm_page - Retrieve PHY page address + * @page: page to access + * + * Returns the phy address for the page requested. + **/ +static u32 e1000_get_phy_addr_for_bm_page(u32 page, u32 reg) +{ + u32 phy_addr = 2; + + if ((page >= 768) || (page == 0 && reg == 25) || (reg == 31)) + phy_addr = 1; + + return phy_addr; +} + +/** + * e1000e_write_phy_reg_bm - Write BM PHY register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary, then writes the data to PHY register + * at the offset. Release any acquired semaphores before exiting. + **/ +s32 e1000e_write_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 data) +{ + s32 ret_val; + u32 page_select = 0; + u32 page = offset >> IGP_PAGE_SHIFT; + u32 page_shift = 0; + + /* Page 800 works differently than the rest so it has its own func */ + if (page == BM_WUC_PAGE) { + ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, &data, + false); + goto out; + } + + ret_val = hw->phy.ops.acquire_phy(hw); + if (ret_val) + goto out; + + hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset); + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + /* + * Page select is register 31 for phy address 1 and 22 for + * phy address 2 and 3. Page select is shifted only for + * phy address 1. + */ + if (hw->phy.addr == 1) { + page_shift = IGP_PAGE_SHIFT; + page_select = IGP01E1000_PHY_PAGE_SELECT; + } else { + page_shift = 0; + page_select = BM_PHY_PAGE_SELECT; + } + + /* Page is shifted left, PHY expects (page x 32) */ + ret_val = e1000e_write_phy_reg_mdic(hw, page_select, + (page << page_shift)); + if (ret_val) { + hw->phy.ops.release_phy(hw); + goto out; + } + } + + ret_val = e1000e_write_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + + hw->phy.ops.release_phy(hw); + +out: + return ret_val; +} + +/** + * e1000e_read_phy_reg_bm - Read BM PHY register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. + **/ +s32 e1000e_read_phy_reg_bm(struct e1000_hw *hw, u32 offset, u16 *data) +{ + s32 ret_val; + u32 page_select = 0; + u32 page = offset >> IGP_PAGE_SHIFT; + u32 page_shift = 0; + + /* Page 800 works differently than the rest so it has its own func */ + if (page == BM_WUC_PAGE) { + ret_val = e1000_access_phy_wakeup_reg_bm(hw, offset, data, + true); + goto out; + } + + ret_val = hw->phy.ops.acquire_phy(hw); + if (ret_val) + goto out; + + hw->phy.addr = e1000_get_phy_addr_for_bm_page(page, offset); + + if (offset > MAX_PHY_MULTI_PAGE_REG) { + /* + * Page select is register 31 for phy address 1 and 22 for + * phy address 2 and 3. Page select is shifted only for + * phy address 1. + */ + if (hw->phy.addr == 1) { + page_shift = IGP_PAGE_SHIFT; + page_select = IGP01E1000_PHY_PAGE_SELECT; + } else { + page_shift = 0; + page_select = BM_PHY_PAGE_SELECT; + } + + /* Page is shifted left, PHY expects (page x 32) */ + ret_val = e1000e_write_phy_reg_mdic(hw, page_select, + (page << page_shift)); + if (ret_val) { + hw->phy.ops.release_phy(hw); + goto out; + } + } + + ret_val = e1000e_read_phy_reg_mdic(hw, MAX_PHY_REG_ADDRESS & offset, + data); + hw->phy.ops.release_phy(hw); + +out: + return ret_val; +} + +/** + * e1000_access_phy_wakeup_reg_bm - Read BM PHY wakeup register + * @hw: pointer to the HW structure + * @offset: register offset to be read or written + * @data: pointer to the data to read or write + * @read: determines if operation is read or write + * + * Acquires semaphore, if necessary, then reads the PHY register at offset + * and storing the retrieved information in data. Release any acquired + * semaphores before exiting. Note that procedure to read the wakeup + * registers are different. It works as such: + * 1) Set page 769, register 17, bit 2 = 1 + * 2) Set page to 800 for host (801 if we were manageability) + * 3) Write the address using the address opcode (0x11) + * 4) Read or write the data using the data opcode (0x12) + * 5) Restore 769_17.2 to its original value + **/ +static s32 e1000_access_phy_wakeup_reg_bm(struct e1000_hw *hw, u32 offset, + u16 *data, bool read) +{ + s32 ret_val; + u16 reg = ((u16)offset) & PHY_REG_MASK; + u16 phy_reg = 0; + u8 phy_acquired = 1; + + + ret_val = hw->phy.ops.acquire_phy(hw); + if (ret_val) { + phy_acquired = 0; + goto out; + } + + /* All operations in this function are phy address 1 */ + hw->phy.addr = 1; + + /* Set page 769 */ + e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, + (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT)); + + ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, &phy_reg); + if (ret_val) + goto out; + + /* First clear bit 4 to avoid a power state change */ + phy_reg &= ~(BM_WUC_HOST_WU_BIT); + ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg); + if (ret_val) + goto out; + + /* Write bit 2 = 1, and clear bit 4 to 769_17 */ + ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, + phy_reg | BM_WUC_ENABLE_BIT); + if (ret_val) + goto out; + + /* Select page 800 */ + ret_val = e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, + (BM_WUC_PAGE << IGP_PAGE_SHIFT)); + + /* Write the page 800 offset value using opcode 0x11 */ + ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ADDRESS_OPCODE, reg); + if (ret_val) + goto out; + + if (read) { + /* Read the page 800 value using opcode 0x12 */ + ret_val = e1000e_read_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE, + data); + } else { + /* Read the page 800 value using opcode 0x12 */ + ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_DATA_OPCODE, + *data); + } + + if (ret_val) + goto out; + + /* + * Restore 769_17.2 to its original value + * Set page 769 + */ + e1000e_write_phy_reg_mdic(hw, IGP01E1000_PHY_PAGE_SELECT, + (BM_WUC_ENABLE_PAGE << IGP_PAGE_SHIFT)); + + /* Clear 769_17.2 */ + ret_val = e1000e_write_phy_reg_mdic(hw, BM_WUC_ENABLE_REG, phy_reg); + +out: + if (phy_acquired == 1) + hw->phy.ops.release_phy(hw); + return ret_val; +} + +/** * e1000e_commit_phy - Soft PHY reset * @hw: pointer to the HW structure * |