diff options
Diffstat (limited to 'drivers/pci/probe.c')
| -rw-r--r-- | drivers/pci/probe.c | 147 |
1 files changed, 147 insertions, 0 deletions
diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c index 795c9026d55..f3f94a5c068 100644 --- a/drivers/pci/probe.c +++ b/drivers/pci/probe.c @@ -856,6 +856,8 @@ void set_pcie_port_type(struct pci_dev *pdev) pdev->pcie_cap = pos; pci_read_config_word(pdev, pos + PCI_EXP_FLAGS, ®16); pdev->pcie_type = (reg16 & PCI_EXP_FLAGS_TYPE) >> 4; + pci_read_config_word(pdev, pos + PCI_EXP_DEVCAP, ®16); + pdev->pcie_mpss = reg16 & PCI_EXP_DEVCAP_PAYLOAD; } void set_pcie_hotplug_bridge(struct pci_dev *pdev) @@ -1326,6 +1328,151 @@ int pci_scan_slot(struct pci_bus *bus, int devfn) return nr; } +static int pcie_find_smpss(struct pci_dev *dev, void *data) +{ + u8 *smpss = data; + + if (!pci_is_pcie(dev)) + return 0; + + /* For PCIE hotplug enabled slots not connected directly to a + * PCI-E root port, there can be problems when hotplugging + * devices. This is due to the possibility of hotplugging a + * device into the fabric with a smaller MPS that the devices + * currently running have configured. Modifying the MPS on the + * running devices could cause a fatal bus error due to an + * incoming frame being larger than the newly configured MPS. + * To work around this, the MPS for the entire fabric must be + * set to the minimum size. Any devices hotplugged into this + * fabric will have the minimum MPS set. If the PCI hotplug + * slot is directly connected to the root port and there are not + * other devices on the fabric (which seems to be the most + * common case), then this is not an issue and MPS discovery + * will occur as normal. + */ + if (dev->is_hotplug_bridge && (!list_is_singular(&dev->bus->devices) || + (dev->bus->self && + dev->bus->self->pcie_type != PCI_EXP_TYPE_ROOT_PORT))) + *smpss = 0; + + if (*smpss > dev->pcie_mpss) + *smpss = dev->pcie_mpss; + + return 0; +} + +static void pcie_write_mps(struct pci_dev *dev, int mps) +{ + int rc, dev_mpss; + + dev_mpss = 128 << dev->pcie_mpss; + + if (pcie_bus_config == PCIE_BUS_PERFORMANCE) { + if (dev->bus->self) { + dev_dbg(&dev->bus->dev, "Bus MPSS %d\n", + 128 << dev->bus->self->pcie_mpss); + + /* For "MPS Force Max", the assumption is made that + * downstream communication will never be larger than + * the MRRS. So, the MPS only needs to be configured + * for the upstream communication. This being the case, + * walk from the top down and set the MPS of the child + * to that of the parent bus. + */ + mps = 128 << dev->bus->self->pcie_mpss; + if (mps > dev_mpss) + dev_warn(&dev->dev, "MPS configured higher than" + " maximum supported by the device. If" + " a bus issue occurs, try running with" + " pci=pcie_bus_safe.\n"); + } + + dev->pcie_mpss = ffs(mps) - 8; + } + + rc = pcie_set_mps(dev, mps); + if (rc) + dev_err(&dev->dev, "Failed attempting to set the MPS\n"); +} + +static void pcie_write_mrrs(struct pci_dev *dev, int mps) +{ + int rc, mrrs, dev_mpss; + + /* In the "safe" case, do not configure the MRRS. There appear to be + * issues with setting MRRS to 0 on a number of devices. + */ + + if (pcie_bus_config != PCIE_BUS_PERFORMANCE) + return; + + dev_mpss = 128 << dev->pcie_mpss; + + /* For Max performance, the MRRS must be set to the largest supported + * value. However, it cannot be configured larger than the MPS the + * device or the bus can support. This assumes that the largest MRRS + * available on the device cannot be smaller than the device MPSS. + */ + mrrs = min(mps, dev_mpss); + + /* MRRS is a R/W register. Invalid values can be written, but a + * subsequent read will verify if the value is acceptable or not. + * If the MRRS value provided is not acceptable (e.g., too large), + * shrink the value until it is acceptable to the HW. + */ + while (mrrs != pcie_get_readrq(dev) && mrrs >= 128) { + dev_warn(&dev->dev, "Attempting to modify the PCI-E MRRS value" + " to %d. If any issues are encountered, please try " + "running with pci=pcie_bus_safe\n", mrrs); + rc = pcie_set_readrq(dev, mrrs); + if (rc) + dev_err(&dev->dev, + "Failed attempting to set the MRRS\n"); + + mrrs /= 2; + } +} + +static int pcie_bus_configure_set(struct pci_dev *dev, void *data) +{ + int mps = 128 << *(u8 *)data; + + if (!pci_is_pcie(dev)) + return 0; + + dev_dbg(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n", + pcie_get_mps(dev), 128<<dev->pcie_mpss, pcie_get_readrq(dev)); + + pcie_write_mps(dev, mps); + pcie_write_mrrs(dev, mps); + + dev_dbg(&dev->dev, "Dev MPS %d MPSS %d MRRS %d\n", + pcie_get_mps(dev), 128<<dev->pcie_mpss, pcie_get_readrq(dev)); + + return 0; +} + +/* pcie_bus_configure_mps requires that pci_walk_bus work in a top-down, + * parents then children fashion. If this changes, then this code will not + * work as designed. + */ +void pcie_bus_configure_settings(struct pci_bus *bus, u8 mpss) +{ + u8 smpss = mpss; + + if (!pci_is_pcie(bus->self)) + return; + + if (pcie_bus_config == PCIE_BUS_SAFE) { + pcie_find_smpss(bus->self, &smpss); + pci_walk_bus(bus, pcie_find_smpss, &smpss); + } + + pcie_bus_configure_set(bus->self, &smpss); + pci_walk_bus(bus, pcie_bus_configure_set, &smpss); +} +EXPORT_SYMBOL_GPL(pcie_bus_configure_settings); + unsigned int __devinit pci_scan_child_bus(struct pci_bus *bus) { unsigned int devfn, pass, max = bus->secondary; |