diff options
Diffstat (limited to 'drivers/pci/quirks.c')
| -rw-r--r-- | drivers/pci/quirks.c | 246 |
1 files changed, 230 insertions, 16 deletions
diff --git a/drivers/pci/quirks.c b/drivers/pci/quirks.c index 7cfa7c38d31..3ea0b29c010 100644 --- a/drivers/pci/quirks.c +++ b/drivers/pci/quirks.c @@ -25,14 +25,9 @@ #include <linux/dmi.h> #include <linux/pci-aspm.h> #include <linux/ioport.h> +#include <asm/dma.h> /* isa_dma_bridge_buggy */ #include "pci.h" -int isa_dma_bridge_buggy; -EXPORT_SYMBOL(isa_dma_bridge_buggy); -int pci_pci_problems; -EXPORT_SYMBOL(pci_pci_problems); - -#ifdef CONFIG_PCI_QUIRKS /* * This quirk function disables memory decoding and releases memory resources * of the device specified by kernel's boot parameter 'pci=resource_alignment='. @@ -338,6 +333,23 @@ static void __devinit quirk_s3_64M(struct pci_dev *dev) DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_868, quirk_s3_64M); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_968, quirk_s3_64M); +/* + * Some CS5536 BIOSes (for example, the Soekris NET5501 board w/ comBIOS + * ver. 1.33 20070103) don't set the correct ISA PCI region header info. + * BAR0 should be 8 bytes; instead, it may be set to something like 8k + * (which conflicts w/ BAR1's memory range). + */ +static void __devinit quirk_cs5536_vsa(struct pci_dev *dev) +{ + if (pci_resource_len(dev, 0) != 8) { + struct resource *res = &dev->resource[0]; + res->end = res->start + 8 - 1; + dev_info(&dev->dev, "CS5536 ISA bridge bug detected " + "(incorrect header); workaround applied.\n"); + } +} +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_CS5536_ISA, quirk_cs5536_vsa); + static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region, unsigned size, int nr, const char *name) { @@ -356,8 +368,9 @@ static void __devinit quirk_io_region(struct pci_dev *dev, unsigned region, bus_region.end = res->end; pcibios_bus_to_resource(dev, res, &bus_region); - pci_claim_resource(dev, nr); - dev_info(&dev->dev, "quirk: %pR claimed by %s\n", res, name); + if (pci_claim_resource(dev, nr) == 0) + dev_info(&dev->dev, "quirk: %pR claimed by %s\n", + res, name); } } @@ -1965,11 +1978,25 @@ static void __devinit quirk_via_cx700_pci_parking_caching(struct pci_dev *dev) /* * Disable PCI Bus Parking and PCI Master read caching on CX700 * which causes unspecified timing errors with a VT6212L on the PCI - * bus leading to USB2.0 packet loss. The defaults are that these - * features are turned off but some BIOSes turn them on. + * bus leading to USB2.0 packet loss. + * + * This quirk is only enabled if a second (on the external PCI bus) + * VT6212L is found -- the CX700 core itself also contains a USB + * host controller with the same PCI ID as the VT6212L. */ + /* Count VT6212L instances */ + struct pci_dev *p = pci_get_device(PCI_VENDOR_ID_VIA, + PCI_DEVICE_ID_VIA_8235_USB_2, NULL); uint8_t b; + + /* p should contain the first (internal) VT6212L -- see if we have + an external one by searching again */ + p = pci_get_device(PCI_VENDOR_ID_VIA, PCI_DEVICE_ID_VIA_8235_USB_2, p); + if (!p) + return; + pci_dev_put(p); + if (pci_read_config_byte(dev, 0x76, &b) == 0) { if (b & 0x40) { /* Turn off PCI Bus Parking */ @@ -1996,7 +2023,7 @@ static void __devinit quirk_via_cx700_pci_parking_caching(struct pci_dev *dev) } } } -DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0x324e, quirk_via_cx700_pci_parking_caching); /* * For Broadcom 5706, 5708, 5709 rev. A nics, any read beyond the @@ -2096,6 +2123,7 @@ static void __devinit quirk_disable_msi(struct pci_dev *dev) } } DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_8131_BRIDGE, quirk_disable_msi); +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_VIA, 0xa238, quirk_disable_msi); /* Go through the list of Hypertransport capabilities and * return 1 if a HT MSI capability is found and enabled */ @@ -2467,6 +2495,39 @@ DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4374, DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ATI, 0x4375, quirk_msi_intx_disable_bug); +/* + * MSI does not work with the AMD RS780/RS880 internal graphics and HDMI audio + * devices unless the BIOS has initialized the nb_cntl.strap_msi_enable bit. + */ +static void __init rs780_int_gfx_disable_msi(struct pci_dev *int_gfx_bridge) +{ + u32 nb_cntl; + + if (!int_gfx_bridge->subordinate) + return; + + pci_bus_write_config_dword(int_gfx_bridge->bus, PCI_DEVFN(0, 0), + 0x60, 0); + pci_bus_read_config_dword(int_gfx_bridge->bus, PCI_DEVFN(0, 0), + 0x64, &nb_cntl); + + if (!(nb_cntl & BIT(10))) { + dev_warn(&int_gfx_bridge->dev, + FW_WARN "RS780: MSI for internal graphics disabled\n"); + int_gfx_bridge->subordinate->bus_flags |= PCI_BUS_FLAGS_NO_MSI; + } +} + +#define PCI_DEVICE_ID_AMD_RS780_P2P_INT_GFX 0x9602 + +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_AMD, + PCI_DEVICE_ID_AMD_RS780_P2P_INT_GFX, + rs780_int_gfx_disable_msi); +/* wrong vendor ID on M4A785TD motherboard: */ +DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_ASUSTEK, + PCI_DEVICE_ID_AMD_RS780_P2P_INT_GFX, + rs780_int_gfx_disable_msi); + #endif /* CONFIG_PCI_MSI */ #ifdef CONFIG_PCI_IOV @@ -2517,9 +2578,95 @@ DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10e7, quirk_i82576_sriov); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x10e8, quirk_i82576_sriov); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x150a, quirk_i82576_sriov); DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x150d, quirk_i82576_sriov); +DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, 0x1518, quirk_i82576_sriov); #endif /* CONFIG_PCI_IOV */ +/* + * This is a quirk for the Ricoh MMC controller found as a part of + * some mulifunction chips. + + * This is very similiar and based on the ricoh_mmc driver written by + * Philip Langdale. Thank you for these magic sequences. + * + * These chips implement the four main memory card controllers (SD, MMC, MS, xD) + * and one or both of cardbus or firewire. + * + * It happens that they implement SD and MMC + * support as separate controllers (and PCI functions). The linux SDHCI + * driver supports MMC cards but the chip detects MMC cards in hardware + * and directs them to the MMC controller - so the SDHCI driver never sees + * them. + * + * To get around this, we must disable the useless MMC controller. + * At that point, the SDHCI controller will start seeing them + * It seems to be the case that the relevant PCI registers to deactivate the + * MMC controller live on PCI function 0, which might be the cardbus controller + * or the firewire controller, depending on the particular chip in question + * + * This has to be done early, because as soon as we disable the MMC controller + * other pci functions shift up one level, e.g. function #2 becomes function + * #1, and this will confuse the pci core. + */ + +#ifdef CONFIG_MMC_RICOH_MMC +static void ricoh_mmc_fixup_rl5c476(struct pci_dev *dev) +{ + /* disable via cardbus interface */ + u8 write_enable; + u8 write_target; + u8 disable; + + /* disable must be done via function #0 */ + if (PCI_FUNC(dev->devfn)) + return; + + pci_read_config_byte(dev, 0xB7, &disable); + if (disable & 0x02) + return; + + pci_read_config_byte(dev, 0x8E, &write_enable); + pci_write_config_byte(dev, 0x8E, 0xAA); + pci_read_config_byte(dev, 0x8D, &write_target); + pci_write_config_byte(dev, 0x8D, 0xB7); + pci_write_config_byte(dev, 0xB7, disable | 0x02); + pci_write_config_byte(dev, 0x8E, write_enable); + pci_write_config_byte(dev, 0x8D, write_target); + + dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via cardbus function)\n"); + dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n"); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_RL5C476, ricoh_mmc_fixup_rl5c476); + +static void ricoh_mmc_fixup_r5c832(struct pci_dev *dev) +{ + /* disable via firewire interface */ + u8 write_enable; + u8 disable; + + /* disable must be done via function #0 */ + if (PCI_FUNC(dev->devfn)) + return; + + pci_read_config_byte(dev, 0xCB, &disable); + + if (disable & 0x02) + return; + + pci_read_config_byte(dev, 0xCA, &write_enable); + pci_write_config_byte(dev, 0xCA, 0x57); + pci_write_config_byte(dev, 0xCB, disable | 0x02); + pci_write_config_byte(dev, 0xCA, write_enable); + + dev_notice(&dev->dev, "proprietary Ricoh MMC controller disabled (via firewire function)\n"); + dev_notice(&dev->dev, "MMC cards are now supported by standard SDHCI controller\n"); +} +DECLARE_PCI_FIXUP_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); +DECLARE_PCI_FIXUP_RESUME_EARLY(PCI_VENDOR_ID_RICOH, PCI_DEVICE_ID_RICOH_R5C832, ricoh_mmc_fixup_r5c832); +#endif /*CONFIG_MMC_RICOH_MMC*/ + + static void pci_do_fixups(struct pci_dev *dev, struct pci_fixup *f, struct pci_fixup *end) { @@ -2595,6 +2742,7 @@ void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) } pci_do_fixups(dev, start, end); } +EXPORT_SYMBOL(pci_fixup_device); static int __init pci_apply_final_quirks(void) { @@ -2629,14 +2777,80 @@ static int __init pci_apply_final_quirks(void) if (!pci_cache_line_size) { printk(KERN_DEBUG "PCI: CLS %u bytes, default %u\n", cls << 2, pci_dfl_cache_line_size << 2); - pci_cache_line_size = cls; + pci_cache_line_size = cls ? cls : pci_dfl_cache_line_size; } return 0; } fs_initcall_sync(pci_apply_final_quirks); -#else -void pci_fixup_device(enum pci_fixup_pass pass, struct pci_dev *dev) {} -#endif -EXPORT_SYMBOL(pci_fixup_device); + +/* + * Followings are device-specific reset methods which can be used to + * reset a single function if other methods (e.g. FLR, PM D0->D3) are + * not available. + */ +static int reset_intel_generic_dev(struct pci_dev *dev, int probe) +{ + int pos; + + /* only implement PCI_CLASS_SERIAL_USB at present */ + if (dev->class == PCI_CLASS_SERIAL_USB) { + pos = pci_find_capability(dev, PCI_CAP_ID_VNDR); + if (!pos) + return -ENOTTY; + + if (probe) + return 0; + + pci_write_config_byte(dev, pos + 0x4, 1); + msleep(100); + + return 0; + } else { + return -ENOTTY; + } +} + +static int reset_intel_82599_sfp_virtfn(struct pci_dev *dev, int probe) +{ + int pos; + + pos = pci_find_capability(dev, PCI_CAP_ID_EXP); + if (!pos) + return -ENOTTY; + + if (probe) + return 0; + + pci_write_config_word(dev, pos + PCI_EXP_DEVCTL, + PCI_EXP_DEVCTL_BCR_FLR); + msleep(100); + + return 0; +} + +#define PCI_DEVICE_ID_INTEL_82599_SFP_VF 0x10ed + +static const struct pci_dev_reset_methods pci_dev_reset_methods[] = { + { PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82599_SFP_VF, + reset_intel_82599_sfp_virtfn }, + { PCI_VENDOR_ID_INTEL, PCI_ANY_ID, + reset_intel_generic_dev }, + { 0 } +}; + +int pci_dev_specific_reset(struct pci_dev *dev, int probe) +{ + const struct pci_dev_reset_methods *i; + + for (i = pci_dev_reset_methods; i->reset; i++) { + if ((i->vendor == dev->vendor || + i->vendor == (u16)PCI_ANY_ID) && + (i->device == dev->device || + i->device == (u16)PCI_ANY_ID)) + return i->reset(dev, probe); + } + + return -ENOTTY; +} |