diff options
Diffstat (limited to 'drivers/power')
-rw-r--r-- | drivers/power/Kconfig | 11 | ||||
-rw-r--r-- | drivers/power/Makefile | 1 | ||||
-rw-r--r-- | drivers/power/bq27x00_battery.c | 177 | ||||
-rw-r--r-- | drivers/power/da9030_battery.c | 2 | ||||
-rw-r--r-- | drivers/power/max8925_power.c | 534 | ||||
-rw-r--r-- | drivers/power/wm8350_power.c | 26 | ||||
-rw-r--r-- | drivers/power/wm97xx_battery.c | 14 |
7 files changed, 701 insertions, 64 deletions
diff --git a/drivers/power/Kconfig b/drivers/power/Kconfig index d4b3d67f054..faaa9b4d0d0 100644 --- a/drivers/power/Kconfig +++ b/drivers/power/Kconfig @@ -29,6 +29,13 @@ config APM_POWER Say Y here to enable support APM status emulation using battery class devices. +config MAX8925_POWER + tristate "MAX8925 battery charger support" + depends on MFD_MAX8925 + help + Say Y here to enable support for the battery charger in the Maxim + MAX8925 PMIC. + config WM831X_BACKUP tristate "WM831X backup battery charger support" depends on MFD_WM831X @@ -98,10 +105,10 @@ config BATTERY_WM97XX Say Y to enable support for battery measured by WM97xx aux port. config BATTERY_BQ27x00 - tristate "BQ27200 battery driver" + tristate "BQ27x00 battery driver" depends on I2C help - Say Y here to enable support for batteries with BQ27200(I2C) chip. + Say Y here to enable support for batteries with BQ27x00 (I2C) chips. config BATTERY_DA9030 tristate "DA9030 battery driver" diff --git a/drivers/power/Makefile b/drivers/power/Makefile index 573597c683b..a2ba7c85c97 100644 --- a/drivers/power/Makefile +++ b/drivers/power/Makefile @@ -16,6 +16,7 @@ obj-$(CONFIG_POWER_SUPPLY) += power_supply.o obj-$(CONFIG_PDA_POWER) += pda_power.o obj-$(CONFIG_APM_POWER) += apm_power.o +obj-$(CONFIG_MAX8925_POWER) += max8925_power.o obj-$(CONFIG_WM831X_BACKUP) += wm831x_backup.o obj-$(CONFIG_WM831X_POWER) += wm831x_power.o obj-$(CONFIG_WM8350_POWER) += wm8350_power.o diff --git a/drivers/power/bq27x00_battery.c b/drivers/power/bq27x00_battery.c index 62bb98124e2..bece33ed873 100644 --- a/drivers/power/bq27x00_battery.c +++ b/drivers/power/bq27x00_battery.c @@ -26,13 +26,22 @@ #include <linux/i2c.h> #include <asm/unaligned.h> -#define DRIVER_VERSION "1.0.0" +#define DRIVER_VERSION "1.1.0" #define BQ27x00_REG_TEMP 0x06 #define BQ27x00_REG_VOLT 0x08 -#define BQ27x00_REG_RSOC 0x0B /* Relative State-of-Charge */ #define BQ27x00_REG_AI 0x14 #define BQ27x00_REG_FLAGS 0x0A +#define BQ27x00_REG_TTE 0x16 +#define BQ27x00_REG_TTF 0x18 +#define BQ27x00_REG_TTECP 0x26 + +#define BQ27000_REG_RSOC 0x0B /* Relative State-of-Charge */ +#define BQ27000_FLAG_CHGS BIT(7) + +#define BQ27500_REG_SOC 0x2c +#define BQ27500_FLAG_DSC BIT(0) +#define BQ27500_FLAG_FC BIT(9) /* If the system has several batteries we need a different name for each * of them... @@ -46,25 +55,28 @@ struct bq27x00_access_methods { struct bq27x00_device_info *di); }; +enum bq27x00_chip { BQ27000, BQ27500 }; + struct bq27x00_device_info { struct device *dev; int id; - int voltage_uV; - int current_uA; - int temp_C; - int charge_rsoc; struct bq27x00_access_methods *bus; struct power_supply bat; + enum bq27x00_chip chip; struct i2c_client *client; }; static enum power_supply_property bq27x00_battery_props[] = { + POWER_SUPPLY_PROP_STATUS, POWER_SUPPLY_PROP_PRESENT, POWER_SUPPLY_PROP_VOLTAGE_NOW, POWER_SUPPLY_PROP_CURRENT_NOW, POWER_SUPPLY_PROP_CAPACITY, POWER_SUPPLY_PROP_TEMP, + POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW, + POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG, + POWER_SUPPLY_PROP_TIME_TO_FULL_NOW, }; /* @@ -74,16 +86,11 @@ static enum power_supply_property bq27x00_battery_props[] = { static int bq27x00_read(u8 reg, int *rt_value, int b_single, struct bq27x00_device_info *di) { - int ret; - - ret = di->bus->read(reg, rt_value, b_single, di); - *rt_value = be16_to_cpu(*rt_value); - - return ret; + return di->bus->read(reg, rt_value, b_single, di); } /* - * Return the battery temperature in Celsius degrees + * Return the battery temperature in tenths of degree Celsius * Or < 0 if something fails. */ static int bq27x00_battery_temperature(struct bq27x00_device_info *di) @@ -97,7 +104,10 @@ static int bq27x00_battery_temperature(struct bq27x00_device_info *di) return ret; } - return (temp >> 2) - 273; + if (di->chip == BQ27500) + return temp - 2731; + else + return ((temp >> 2) - 273) * 10; } /* @@ -115,7 +125,7 @@ static int bq27x00_battery_voltage(struct bq27x00_device_info *di) return ret; } - return volt; + return volt * 1000; } /* @@ -134,16 +144,23 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di) dev_err(di->dev, "error reading current\n"); return 0; } - ret = bq27x00_read(BQ27x00_REG_FLAGS, &flags, 0, di); - if (ret < 0) { - dev_err(di->dev, "error reading flags\n"); - return 0; - } - if ((flags & (1 << 7)) != 0) { - dev_dbg(di->dev, "negative current!\n"); - return -curr; + + if (di->chip == BQ27500) { + /* bq27500 returns signed value */ + curr = (int)(s16)curr; + } else { + ret = bq27x00_read(BQ27x00_REG_FLAGS, &flags, 0, di); + if (ret < 0) { + dev_err(di->dev, "error reading flags\n"); + return 0; + } + if (flags & BQ27000_FLAG_CHGS) { + dev_dbg(di->dev, "negative current!\n"); + curr = -curr; + } } - return curr; + + return curr * 1000; } /* @@ -155,13 +172,70 @@ static int bq27x00_battery_rsoc(struct bq27x00_device_info *di) int ret; int rsoc = 0; - ret = bq27x00_read(BQ27x00_REG_RSOC, &rsoc, 1, di); + if (di->chip == BQ27500) + ret = bq27x00_read(BQ27500_REG_SOC, &rsoc, 0, di); + else + ret = bq27x00_read(BQ27000_REG_RSOC, &rsoc, 1, di); if (ret) { dev_err(di->dev, "error reading relative State-of-Charge\n"); return ret; } - return rsoc >> 8; + return rsoc; +} + +static int bq27x00_battery_status(struct bq27x00_device_info *di, + union power_supply_propval *val) +{ + int flags = 0; + int status; + int ret; + + ret = bq27x00_read(BQ27x00_REG_FLAGS, &flags, 0, di); + if (ret < 0) { + dev_err(di->dev, "error reading flags\n"); + return ret; + } + + if (di->chip == BQ27500) { + if (flags & BQ27500_FLAG_FC) + status = POWER_SUPPLY_STATUS_FULL; + else if (flags & BQ27500_FLAG_DSC) + status = POWER_SUPPLY_STATUS_DISCHARGING; + else + status = POWER_SUPPLY_STATUS_CHARGING; + } else { + if (flags & BQ27000_FLAG_CHGS) + status = POWER_SUPPLY_STATUS_CHARGING; + else + status = POWER_SUPPLY_STATUS_DISCHARGING; + } + + val->intval = status; + return 0; +} + +/* + * Read a time register. + * Return < 0 if something fails. + */ +static int bq27x00_battery_time(struct bq27x00_device_info *di, int reg, + union power_supply_propval *val) +{ + int tval = 0; + int ret; + + ret = bq27x00_read(reg, &tval, 0, di); + if (ret) { + dev_err(di->dev, "error reading register %02x\n", reg); + return ret; + } + + if (tval == 65535) + return -ENODATA; + + val->intval = tval * 60; + return 0; } #define to_bq27x00_device_info(x) container_of((x), \ @@ -171,9 +245,13 @@ static int bq27x00_battery_get_property(struct power_supply *psy, enum power_supply_property psp, union power_supply_propval *val) { + int ret = 0; struct bq27x00_device_info *di = to_bq27x00_device_info(psy); switch (psp) { + case POWER_SUPPLY_PROP_STATUS: + ret = bq27x00_battery_status(di, val); + break; case POWER_SUPPLY_PROP_VOLTAGE_NOW: case POWER_SUPPLY_PROP_PRESENT: val->intval = bq27x00_battery_voltage(di); @@ -189,11 +267,20 @@ static int bq27x00_battery_get_property(struct power_supply *psy, case POWER_SUPPLY_PROP_TEMP: val->intval = bq27x00_battery_temperature(di); break; + case POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW: + ret = bq27x00_battery_time(di, BQ27x00_REG_TTE, val); + break; + case POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG: + ret = bq27x00_battery_time(di, BQ27x00_REG_TTECP, val); + break; + case POWER_SUPPLY_PROP_TIME_TO_FULL_NOW: + ret = bq27x00_battery_time(di, BQ27x00_REG_TTF, val); + break; default: return -EINVAL; } - return 0; + return ret; } static void bq27x00_powersupply_init(struct bq27x00_device_info *di) @@ -206,10 +293,10 @@ static void bq27x00_powersupply_init(struct bq27x00_device_info *di) } /* - * BQ27200 specific code + * i2c specific code */ -static int bq27200_read(u8 reg, int *rt_value, int b_single, +static int bq27x00_read_i2c(u8 reg, int *rt_value, int b_single, struct bq27x00_device_info *di) { struct i2c_client *client = di->client; @@ -238,7 +325,7 @@ static int bq27200_read(u8 reg, int *rt_value, int b_single, err = i2c_transfer(client->adapter, msg, 1); if (err >= 0) { if (!b_single) - *rt_value = get_unaligned_be16(data); + *rt_value = get_unaligned_le16(data); else *rt_value = data[0]; @@ -248,7 +335,7 @@ static int bq27200_read(u8 reg, int *rt_value, int b_single, return err; } -static int bq27200_battery_probe(struct i2c_client *client, +static int bq27x00_battery_probe(struct i2c_client *client, const struct i2c_device_id *id) { char *name; @@ -267,7 +354,7 @@ static int bq27200_battery_probe(struct i2c_client *client, if (retval < 0) return retval; - name = kasprintf(GFP_KERNEL, "bq27200-%d", num); + name = kasprintf(GFP_KERNEL, "%s-%d", id->name, num); if (!name) { dev_err(&client->dev, "failed to allocate device name\n"); retval = -ENOMEM; @@ -281,6 +368,7 @@ static int bq27200_battery_probe(struct i2c_client *client, goto batt_failed_2; } di->id = num; + di->chip = id->driver_data; bus = kzalloc(sizeof(*bus), GFP_KERNEL); if (!bus) { @@ -293,7 +381,7 @@ static int bq27200_battery_probe(struct i2c_client *client, i2c_set_clientdata(client, di); di->dev = &client->dev; di->bat.name = name; - bus->read = &bq27200_read; + bus->read = &bq27x00_read_i2c; di->bus = bus; di->client = client; @@ -323,7 +411,7 @@ batt_failed_1: return retval; } -static int bq27200_battery_remove(struct i2c_client *client) +static int bq27x00_battery_remove(struct i2c_client *client) { struct bq27x00_device_info *di = i2c_get_clientdata(client); @@ -344,27 +432,28 @@ static int bq27200_battery_remove(struct i2c_client *client) * Module stuff */ -static const struct i2c_device_id bq27200_id[] = { - { "bq27200", 0 }, +static const struct i2c_device_id bq27x00_id[] = { + { "bq27200", BQ27000 }, /* bq27200 is same as bq27000, but with i2c */ + { "bq27500", BQ27500 }, {}, }; -static struct i2c_driver bq27200_battery_driver = { +static struct i2c_driver bq27x00_battery_driver = { .driver = { - .name = "bq27200-battery", + .name = "bq27x00-battery", }, - .probe = bq27200_battery_probe, - .remove = bq27200_battery_remove, - .id_table = bq27200_id, + .probe = bq27x00_battery_probe, + .remove = bq27x00_battery_remove, + .id_table = bq27x00_id, }; static int __init bq27x00_battery_init(void) { int ret; - ret = i2c_add_driver(&bq27200_battery_driver); + ret = i2c_add_driver(&bq27x00_battery_driver); if (ret) - printk(KERN_ERR "Unable to register BQ27200 driver\n"); + printk(KERN_ERR "Unable to register BQ27x00 driver\n"); return ret; } @@ -372,7 +461,7 @@ module_init(bq27x00_battery_init); static void __exit bq27x00_battery_exit(void) { - i2c_del_driver(&bq27200_battery_driver); + i2c_del_driver(&bq27x00_battery_driver); } module_exit(bq27x00_battery_exit); diff --git a/drivers/power/da9030_battery.c b/drivers/power/da9030_battery.c index 3364198134a..a2e71f7b27f 100644 --- a/drivers/power/da9030_battery.c +++ b/drivers/power/da9030_battery.c @@ -509,7 +509,7 @@ static int da9030_battery_probe(struct platform_device *pdev) charger->master = pdev->dev.parent; - /* 10 seconds between monotor runs unless platfrom defines other + /* 10 seconds between monitor runs unless platform defines other interval */ charger->interval = msecs_to_jiffies( (pdata->batmon_interval ? : 10) * 1000); diff --git a/drivers/power/max8925_power.c b/drivers/power/max8925_power.c new file mode 100644 index 00000000000..a1b4410544d --- /dev/null +++ b/drivers/power/max8925_power.c @@ -0,0 +1,534 @@ +/* + * Battery driver for Maxim MAX8925 + * + * Copyright (c) 2009-2010 Marvell International Ltd. + * Haojian Zhuang <haojian.zhuang@marvell.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/module.h> +#include <linux/err.h> +#include <linux/i2c.h> +#include <linux/interrupt.h> +#include <linux/platform_device.h> +#include <linux/power_supply.h> +#include <linux/mfd/max8925.h> + +/* registers in GPM */ +#define MAX8925_OUT5VEN 0x54 +#define MAX8925_OUT3VEN 0x58 +#define MAX8925_CHG_CNTL1 0x7c + +/* bits definition */ +#define MAX8925_CHG_STAT_VSYSLOW (1 << 0) +#define MAX8925_CHG_STAT_MODE_MASK (3 << 2) +#define MAX8925_CHG_STAT_EN_MASK (1 << 4) +#define MAX8925_CHG_MBDET (1 << 1) +#define MAX8925_CHG_AC_RANGE_MASK (3 << 6) + +/* registers in ADC */ +#define MAX8925_ADC_RES_CNFG1 0x06 +#define MAX8925_ADC_AVG_CNFG1 0x07 +#define MAX8925_ADC_ACQ_CNFG1 0x08 +#define MAX8925_ADC_ACQ_CNFG2 0x09 +/* 2 bytes registers in below. MSB is 1st, LSB is 2nd. */ +#define MAX8925_ADC_AUX2 0x62 +#define MAX8925_ADC_VCHG 0x64 +#define MAX8925_ADC_VBBATT 0x66 +#define MAX8925_ADC_VMBATT 0x68 +#define MAX8925_ADC_ISNS 0x6a +#define MAX8925_ADC_THM 0x6c +#define MAX8925_ADC_TDIE 0x6e +#define MAX8925_CMD_AUX2 0xc8 +#define MAX8925_CMD_VCHG 0xd0 +#define MAX8925_CMD_VBBATT 0xd8 +#define MAX8925_CMD_VMBATT 0xe0 +#define MAX8925_CMD_ISNS 0xe8 +#define MAX8925_CMD_THM 0xf0 +#define MAX8925_CMD_TDIE 0xf8 + +enum { + MEASURE_AUX2, + MEASURE_VCHG, + MEASURE_VBBATT, + MEASURE_VMBATT, + MEASURE_ISNS, + MEASURE_THM, + MEASURE_TDIE, + MEASURE_MAX, +}; + +struct max8925_power_info { + struct max8925_chip *chip; + struct i2c_client *gpm; + struct i2c_client *adc; + + struct power_supply ac; + struct power_supply usb; + struct power_supply battery; + int irq_base; + unsigned ac_online:1; + unsigned usb_online:1; + unsigned bat_online:1; + unsigned chg_mode:2; + unsigned batt_detect:1; /* detecing MB by ID pin */ + unsigned topoff_threshold:2; + unsigned fast_charge:3; + + int (*set_charger) (int); +}; + +static int __set_charger(struct max8925_power_info *info, int enable) +{ + struct max8925_chip *chip = info->chip; + if (enable) { + /* enable charger in platform */ + if (info->set_charger) + info->set_charger(1); + /* enable charger */ + max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 1 << 7, 0); + } else { + /* disable charge */ + max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 1 << 7, 1 << 7); + if (info->set_charger) + info->set_charger(0); + } + dev_dbg(chip->dev, "%s\n", (enable) ? "Enable charger" + : "Disable charger"); + return 0; +} + +static irqreturn_t max8925_charger_handler(int irq, void *data) +{ + struct max8925_power_info *info = (struct max8925_power_info *)data; + struct max8925_chip *chip = info->chip; + + switch (irq - chip->irq_base) { + case MAX8925_IRQ_VCHG_DC_R: + info->ac_online = 1; + __set_charger(info, 1); + dev_dbg(chip->dev, "Adapter inserted\n"); + break; + case MAX8925_IRQ_VCHG_DC_F: + info->ac_online = 0; + __set_charger(info, 0); + dev_dbg(chip->dev, "Adapter is removal\n"); + break; + case MAX8925_IRQ_VCHG_USB_R: + info->usb_online = 1; + __set_charger(info, 1); + dev_dbg(chip->dev, "USB inserted\n"); + break; + case MAX8925_IRQ_VCHG_USB_F: + info->usb_online = 0; + __set_charger(info, 0); + dev_dbg(chip->dev, "USB is removal\n"); + break; + case MAX8925_IRQ_VCHG_THM_OK_F: + /* Battery is not ready yet */ + dev_dbg(chip->dev, "Battery temperature is out of range\n"); + case MAX8925_IRQ_VCHG_DC_OVP: + dev_dbg(chip->dev, "Error detection\n"); + __set_charger(info, 0); + break; + case MAX8925_IRQ_VCHG_THM_OK_R: + /* Battery is ready now */ + dev_dbg(chip->dev, "Battery temperature is in range\n"); + break; + case MAX8925_IRQ_VCHG_SYSLOW_R: + /* VSYS is low */ + dev_info(chip->dev, "Sys power is too low\n"); + break; + case MAX8925_IRQ_VCHG_SYSLOW_F: + dev_dbg(chip->dev, "Sys power is above low threshold\n"); + break; + case MAX8925_IRQ_VCHG_DONE: + __set_charger(info, 0); + dev_dbg(chip->dev, "Charging is done\n"); + break; + case MAX8925_IRQ_VCHG_TOPOFF: + dev_dbg(chip->dev, "Charging in top-off mode\n"); + break; + case MAX8925_IRQ_VCHG_TMR_FAULT: + __set_charger(info, 0); + dev_dbg(chip->dev, "Safe timer is expired\n"); + break; + case MAX8925_IRQ_VCHG_RST: + __set_charger(info, 0); + dev_dbg(chip->dev, "Charger is reset\n"); + break; + } + return IRQ_HANDLED; +} + +static int start_measure(struct max8925_power_info *info, int type) +{ + unsigned char buf[2] = {0, 0}; + int meas_reg = 0, ret; + + switch (type) { + case MEASURE_VCHG: + meas_reg = MAX8925_ADC_VCHG; + break; + case MEASURE_VBBATT: + meas_reg = MAX8925_ADC_VBBATT; + break; + case MEASURE_VMBATT: + meas_reg = MAX8925_ADC_VMBATT; + break; + case MEASURE_ISNS: + meas_reg = MAX8925_ADC_ISNS; + break; + default: + return -EINVAL; + } + + max8925_bulk_read(info->adc, meas_reg, 2, buf); + ret = (buf[0] << 4) | (buf[1] >> 4); + + return ret; +} + +static int max8925_ac_get_prop(struct power_supply *psy, + enum power_supply_property psp, + union power_supply_propval *val) +{ + struct max8925_power_info *info = dev_get_drvdata(psy->dev->parent); + int ret = 0; + + switch (psp) { + case POWER_SUPPLY_PROP_ONLINE: + val->intval = info->ac_online; + break; + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + if (info->ac_online) { + ret = start_measure(info, MEASURE_VCHG); + if (ret >= 0) { + val->intval = ret << 1; /* unit is mV */ + goto out; + } + } + ret = -ENODATA; + break; + default: + ret = -ENODEV; + break; + } +out: + return ret; +} + +static enum power_supply_property max8925_ac_props[] = { + POWER_SUPPLY_PROP_ONLINE, + POWER_SUPPLY_PROP_VOLTAGE_NOW, +}; + +static int max8925_usb_get_prop(struct power_supply *psy, + enum power_supply_property psp, + union power_supply_propval *val) +{ + struct max8925_power_info *info = dev_get_drvdata(psy->dev->parent); + int ret = 0; + + switch (psp) { + case POWER_SUPPLY_PROP_ONLINE: + val->intval = info->usb_online; + break; + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + if (info->usb_online) { + ret = start_measure(info, MEASURE_VCHG); + if (ret >= 0) { + val->intval = ret << 1; /* unit is mV */ + goto out; + } + } + ret = -ENODATA; + break; + default: + ret = -ENODEV; + break; + } +out: + return ret; +} + +static enum power_supply_property max8925_usb_props[] = { + POWER_SUPPLY_PROP_ONLINE, + POWER_SUPPLY_PROP_VOLTAGE_NOW, +}; + +static int max8925_bat_get_prop(struct power_supply *psy, + enum power_supply_property psp, + union power_supply_propval *val) +{ + struct max8925_power_info *info = dev_get_drvdata(psy->dev->parent); + long long int tmp = 0; + int ret = 0; + + switch (psp) { + case POWER_SUPPLY_PROP_ONLINE: + val->intval = info->bat_online; + break; + case POWER_SUPPLY_PROP_VOLTAGE_NOW: + if (info->bat_online) { + ret = start_measure(info, MEASURE_VMBATT); + if (ret >= 0) { + val->intval = ret << 1; /* unit is mV */ + ret = 0; + break; + } + } + ret = -ENODATA; + break; + case POWER_SUPPLY_PROP_CURRENT_NOW: + if (info->bat_online) { + ret = start_measure(info, MEASURE_ISNS); + if (ret >= 0) { + tmp = (long long int)ret * 6250 / 4096 - 3125; + ret = (int)tmp; + val->intval = 0; + if (ret > 0) + val->intval = ret; /* unit is mA */ + ret = 0; + break; + } + } + ret = -ENODATA; + break; + case POWER_SUPPLY_PROP_CHARGE_TYPE: + if (!info->bat_online) { + ret = -ENODATA; + break; + } + ret = max8925_reg_read(info->gpm, MAX8925_CHG_STATUS); + ret = (ret & MAX8925_CHG_STAT_MODE_MASK) >> 2; + switch (ret) { + case 1: + val->intval = POWER_SUPPLY_CHARGE_TYPE_FAST; + break; + case 0: + case 2: + val->intval = POWER_SUPPLY_CHARGE_TYPE_TRICKLE; + break; + case 3: + val->intval = POWER_SUPPLY_CHARGE_TYPE_NONE; + break; + } + ret = 0; + break; + case POWER_SUPPLY_PROP_STATUS: + if (!info->bat_online) { + ret = -ENODATA; + break; + } + ret = max8925_reg_read(info->gpm, MAX8925_CHG_STATUS); + if (info->usb_online || info->ac_online) { + val->intval = POWER_SUPPLY_STATUS_NOT_CHARGING; + if (ret & MAX8925_CHG_STAT_EN_MASK) + val->intval = POWER_SUPPLY_STATUS_CHARGING; + } else + val->intval = POWER_SUPPLY_STATUS_DISCHARGING; + ret = 0; + break; + default: + ret = -ENODEV; + break; + } + return ret; +} + +static enum power_supply_property max8925_battery_props[] = { + POWER_SUPPLY_PROP_ONLINE, + POWER_SUPPLY_PROP_VOLTAGE_NOW, + POWER_SUPPLY_PROP_CURRENT_NOW, + POWER_SUPPLY_PROP_CHARGE_TYPE, + POWER_SUPPLY_PROP_STATUS, +}; + +#define REQUEST_IRQ(_irq, _name) \ +do { \ + ret = request_threaded_irq(chip->irq_base + _irq, NULL, \ + max8925_charger_handler, \ + IRQF_ONESHOT, _name, info); \ + if (ret) \ + dev_err(chip->dev, "Failed to request IRQ #%d: %d\n", \ + _irq, ret); \ +} while (0) + +static __devinit int max8925_init_charger(struct max8925_chip *chip, + struct max8925_power_info *info) +{ + int ret; + + REQUEST_IRQ(MAX8925_IRQ_VCHG_DC_OVP, "ac-ovp"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_DC_F, "ac-remove"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_DC_R, "ac-insert"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_USB_OVP, "usb-ovp"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_USB_F, "usb-remove"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_USB_R, "usb-insert"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_THM_OK_R, "batt-temp-in-range"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_THM_OK_F, "batt-temp-out-range"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_SYSLOW_F, "vsys-high"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_SYSLOW_R, "vsys-low"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_RST, "charger-reset"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_DONE, "charger-done"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_TOPOFF, "charger-topoff"); + REQUEST_IRQ(MAX8925_IRQ_VCHG_TMR_FAULT, "charger-timer-expire"); + + info->ac_online = 0; + info->usb_online = 0; + info->bat_online = 0; + ret = max8925_reg_read(info->gpm, MAX8925_CHG_STATUS); + if (ret >= 0) { + /* + * If battery detection is enabled, ID pin of battery is + * connected to MBDET pin of MAX8925. It could be used to + * detect battery presence. + * Otherwise, we have to assume that battery is always on. + */ + if (info->batt_detect) + info->bat_online = (ret & MAX8925_CHG_MBDET) ? 0 : 1; + else + info->bat_online = 1; + if (ret & MAX8925_CHG_AC_RANGE_MASK) + info->ac_online = 1; + else + info->ac_online = 0; + } + /* disable charge */ + max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 1 << 7, 1 << 7); + /* set charging current in charge topoff mode */ + max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 3 << 5, + info->topoff_threshold << 5); + /* set charing current in fast charge mode */ + max8925_set_bits(info->gpm, MAX8925_CHG_CNTL1, 7, info->fast_charge); + + return 0; +} + +static __devexit int max8925_deinit_charger(struct max8925_power_info *info) +{ + struct max8925_chip *chip = info->chip; + int irq; + + irq = chip->irq_base + MAX8925_IRQ_VCHG_DC_OVP; + for (; irq <= chip->irq_base + MAX8925_IRQ_VCHG_TMR_FAULT; irq++) + free_irq(irq, info); + + return 0; +} + +static __devinit int max8925_power_probe(struct platform_device *pdev) +{ + struct max8925_chip *chip = dev_get_drvdata(pdev->dev.parent); + struct max8925_platform_data *max8925_pdata; + struct max8925_power_pdata *pdata = NULL; + struct max8925_power_info *info; + int ret; + + if (pdev->dev.parent->platform_data) { + max8925_pdata = pdev->dev.parent->platform_data; + pdata = max8925_pdata->power; + } + + if (!pdata) { + dev_err(&pdev->dev, "platform data isn't assigned to " + "power supply\n"); + return -EINVAL; + } + + info = kzalloc(sizeof(struct max8925_power_info), GFP_KERNEL); + if (!info) + return -ENOMEM; + info->chip = chip; + info->gpm = chip->i2c; + info->adc = chip->adc; + + info->ac.name = "max8925-ac"; + info->ac.type = POWER_SUPPLY_TYPE_MAINS; + info->ac.properties = max8925_ac_props; + info->ac.num_properties = ARRAY_SIZE(max8925_ac_props); + info->ac.get_property = max8925_ac_get_prop; + ret = power_supply_register(&pdev->dev, &info->ac); + if (ret) + goto out; + info->ac.dev->parent = &pdev->dev; + + info->usb.name = "max8925-usb"; + info->usb.type = POWER_SUPPLY_TYPE_USB; + info->usb.properties = max8925_usb_props; + info->usb.num_properties = ARRAY_SIZE(max8925_usb_props); + info->usb.get_property = max8925_usb_get_prop; + ret = power_supply_register(&pdev->dev, &info->usb); + if (ret) + goto out_usb; + info->usb.dev->parent = &pdev->dev; + + info->battery.name = "max8925-battery"; + info->battery.type = POWER_SUPPLY_TYPE_BATTERY; + info->battery.properties = max8925_battery_props; + info->battery.num_properties = ARRAY_SIZE(max8925_battery_props); + info->battery.get_property = max8925_bat_get_prop; + ret = power_supply_register(&pdev->dev, &info->battery); + if (ret) + goto out_battery; + info->battery.dev->parent = &pdev->dev; + + info->batt_detect = pdata->batt_detect; + info->topoff_threshold = pdata->topoff_threshold; + info->fast_charge = pdata->fast_charge; + info->set_charger = pdata->set_charger; + dev_set_drvdata(&pdev->dev, info); + platform_set_drvdata(pdev, info); + + max8925_init_charger(chip, info); + return 0; +out_battery: + power_supply_unregister(&info->battery); +out_usb: + power_supply_unregister(&info->ac); +out: + kfree(info); + return ret; +} + +static __devexit int max8925_power_remove(struct platform_device *pdev) +{ + struct max8925_power_info *info = platform_get_drvdata(pdev); + + if (info) { + power_supply_unregister(&info->ac); + power_supply_unregister(&info->usb); + power_supply_unregister(&info->battery); + max8925_deinit_charger(info); + kfree(info); + } + return 0; +} + +static struct platform_driver max8925_power_driver = { + .probe = max8925_power_probe, + .remove = __devexit_p(max8925_power_remove), + .driver = { + .name = "max8925-power", + }, +}; + +static int __init max8925_power_init(void) +{ + return platform_driver_register(&max8925_power_driver); +} +module_init(max8925_power_init); + +static void __exit max8925_power_exit(void) +{ + platform_driver_unregister(&max8925_power_driver); +} +module_exit(max8925_power_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("Power supply driver for MAX8925"); +MODULE_ALIAS("platform:max8925-power"); diff --git a/drivers/power/wm8350_power.c b/drivers/power/wm8350_power.c index ad4f071e128..0693902d615 100644 --- a/drivers/power/wm8350_power.c +++ b/drivers/power/wm8350_power.c @@ -190,7 +190,7 @@ static irqreturn_t wm8350_charger_handler(int irq, void *data) struct wm8350_power *power = &wm8350->power; struct wm8350_charger_policy *policy = power->policy; - switch (irq) { + switch (irq - wm8350->irq_base) { case WM8350_IRQ_CHG_BAT_FAIL: dev_err(wm8350->dev, "battery failed\n"); break; @@ -428,18 +428,18 @@ static void wm8350_init_charger(struct wm8350 *wm8350) static void free_charger_irq(struct wm8350 *wm8350) { - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_HOT); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_COLD); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_FAIL); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_TO); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_END); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_START); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P9); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P1); - wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_2P85); - wm8350_free_irq(wm8350, WM8350_IRQ_EXT_USB_FB); - wm8350_free_irq(wm8350, WM8350_IRQ_EXT_WALL_FB); - wm8350_free_irq(wm8350, WM8350_IRQ_EXT_BAT_FB); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_HOT, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_COLD, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_BAT_FAIL, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_TO, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_END, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_START, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P9, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_3P1, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_CHG_VBATT_LT_2P85, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_EXT_USB_FB, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_EXT_WALL_FB, wm8350); + wm8350_free_irq(wm8350, WM8350_IRQ_EXT_BAT_FB, wm8350); } static __devinit int wm8350_power_probe(struct platform_device *pdev) diff --git a/drivers/power/wm97xx_battery.c b/drivers/power/wm97xx_battery.c index fa39e759a27..23eed356a85 100644 --- a/drivers/power/wm97xx_battery.c +++ b/drivers/power/wm97xx_battery.c @@ -26,7 +26,7 @@ static DEFINE_MUTEX(bat_lock); static struct work_struct bat_work; -struct mutex work_lock; +static struct mutex work_lock; static int bat_status = POWER_SUPPLY_STATUS_UNKNOWN; static struct wm97xx_batt_info *gpdata; static enum power_supply_property *prop; @@ -175,8 +175,14 @@ static int __devinit wm97xx_bat_probe(struct platform_device *dev) dev_err(&dev->dev, "Do not pass platform_data through " "wm97xx_bat_set_pdata!\n"); return -EINVAL; - } else - pdata = wmdata->batt_pdata; + } + + if (!wmdata) { + dev_err(&dev->dev, "No platform data supplied\n"); + return -EINVAL; + } + + pdata = wmdata->batt_pdata; if (dev->id != -1) return -EINVAL; @@ -197,7 +203,7 @@ static int __devinit wm97xx_bat_probe(struct platform_device *dev) goto err2; ret = request_irq(gpio_to_irq(pdata->charge_gpio), wm97xx_chrg_irq, IRQF_DISABLED, - "AC Detect", 0); + "AC Detect", dev); if (ret) goto err2; props++; /* POWER_SUPPLY_PROP_STATUS */ |