summaryrefslogtreecommitdiffstats
path: root/drivers/regulator
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/regulator')
-rw-r--r--drivers/regulator/Kconfig27
-rw-r--r--drivers/regulator/Makefile3
-rw-r--r--drivers/regulator/arizona-ldo1.c130
-rw-r--r--drivers/regulator/arizona-micsupp.c2
-rw-r--r--drivers/regulator/as3711-regulator.c369
-rw-r--r--drivers/regulator/core.c31
-rw-r--r--drivers/regulator/da9052-regulator.c10
-rw-r--r--drivers/regulator/da9055-regulator.c680
-rw-r--r--drivers/regulator/gpio-regulator.c4
-rw-r--r--drivers/regulator/lp8788-buck.c18
-rw-r--r--drivers/regulator/lp8788-ldo.c13
-rw-r--r--drivers/regulator/max1586.c44
-rw-r--r--drivers/regulator/max77686.c164
-rw-r--r--drivers/regulator/max8973-regulator.c505
-rw-r--r--drivers/regulator/wm831x-dcdc.c2
15 files changed, 1953 insertions, 49 deletions
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 0ae658f048e..551a22b0753 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -109,6 +109,16 @@ config REGULATOR_DA9052
This driver supports the voltage regulators of DA9052-BC and
DA9053-AA/Bx PMIC.
+config REGULATOR_DA9055
+ tristate "Dialog Semiconductor DA9055 regulators"
+ depends on MFD_DA9055
+ help
+ Say y here to support the BUCKs and LDOs regulators found on
+ Dialog Semiconductor DA9055 PMIC.
+
+ This driver can also be built as a module. If so, the module
+ will be called da9055-regulator.
+
config REGULATOR_FAN53555
tristate "Fairchild FAN53555 Regulator"
depends on I2C
@@ -204,6 +214,16 @@ config REGULATOR_MAX8952
via I2C bus. Maxim 8952 has one voltage output and supports 4 DVS
modes ranging from 0.77V to 1.40V by 0.01V steps.
+config REGULATOR_MAX8973
+ tristate "Maxim MAX8973 voltage regulator "
+ depends on I2C
+ select REGMAP_I2C
+ help
+ The MAXIM MAX8973 high-efficiency. three phase, DC-DC step-down
+ switching regulator delievers up to 9A of output current. Each
+ phase operates at a 2MHz fixed frequency with a 120 deg shift
+ from the adjacent phase, allowing the use of small magnetic component.
+
config REGULATOR_MAX8997
tristate "Maxim 8997/8966 regulator"
depends on MFD_MAX8997
@@ -477,5 +497,12 @@ config REGULATOR_WM8994
This driver provides support for the voltage regulators on the
WM8994 CODEC.
+config REGULATOR_AS3711
+ tristate "AS3711 PMIC"
+ depends on MFD_AS3711
+ help
+ This driver provides support for the voltage regulators on the
+ AS3711 PMIC
+
endif
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 6166d122d12..b802b0c7fb0 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -16,8 +16,10 @@ obj-$(CONFIG_REGULATOR_AB8500) += ab8500.o
obj-$(CONFIG_REGULATOR_AD5398) += ad5398.o
obj-$(CONFIG_REGULATOR_ANATOP) += anatop-regulator.o
obj-$(CONFIG_REGULATOR_ARIZONA) += arizona-micsupp.o arizona-ldo1.o
+obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
obj-$(CONFIG_REGULATOR_DA9052) += da9052-regulator.o
+obj-$(CONFIG_REGULATOR_DA9055) += da9055-regulator.o
obj-$(CONFIG_REGULATOR_DBX500_PRCMU) += dbx500-prcmu.o
obj-$(CONFIG_REGULATOR_DB8500_PRCMU) += db8500-prcmu.o
obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o
@@ -34,6 +36,7 @@ obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
obj-$(CONFIG_REGULATOR_MAX8907) += max8907-regulator.o
obj-$(CONFIG_REGULATOR_MAX8925) += max8925-regulator.o
obj-$(CONFIG_REGULATOR_MAX8952) += max8952.o
+obj-$(CONFIG_REGULATOR_MAX8973) += max8973-regulator.o
obj-$(CONFIG_REGULATOR_MAX8997) += max8997.o
obj-$(CONFIG_REGULATOR_MAX8998) += max8998.o
obj-$(CONFIG_REGULATOR_MAX77686) += max77686.o
diff --git a/drivers/regulator/arizona-ldo1.c b/drivers/regulator/arizona-ldo1.c
index b44fa6f0e94..ed7beec53af 100644
--- a/drivers/regulator/arizona-ldo1.c
+++ b/drivers/regulator/arizona-ldo1.c
@@ -34,6 +34,108 @@ struct arizona_ldo1 {
struct regulator_init_data init_data;
};
+static int arizona_ldo1_hc_list_voltage(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ if (selector >= rdev->desc->n_voltages)
+ return -EINVAL;
+
+ if (selector == rdev->desc->n_voltages - 1)
+ return 1800000;
+ else
+ return rdev->desc->min_uV + (rdev->desc->uV_step * selector);
+}
+
+static int arizona_ldo1_hc_map_voltage(struct regulator_dev *rdev,
+ int min_uV, int max_uV)
+{
+ int sel;
+
+ sel = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step);
+ if (sel >= rdev->desc->n_voltages)
+ sel = rdev->desc->n_voltages - 1;
+
+ return sel;
+}
+
+static int arizona_ldo1_hc_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned sel)
+{
+ struct arizona_ldo1 *ldo = rdev_get_drvdata(rdev);
+ struct regmap *regmap = ldo->arizona->regmap;
+ unsigned int val;
+ int ret;
+
+ if (sel == rdev->desc->n_voltages - 1)
+ val = ARIZONA_LDO1_HI_PWR;
+ else
+ val = 0;
+
+ ret = regmap_update_bits(regmap, ARIZONA_LDO1_CONTROL_2,
+ ARIZONA_LDO1_HI_PWR, val);
+ if (ret != 0)
+ return ret;
+
+ ret = regmap_update_bits(regmap, ARIZONA_DYNAMIC_FREQUENCY_SCALING_1,
+ ARIZONA_SUBSYS_MAX_FREQ, val);
+ if (ret != 0)
+ return ret;
+
+ if (val)
+ return 0;
+
+ val = sel << ARIZONA_LDO1_VSEL_SHIFT;
+
+ return regmap_update_bits(regmap, ARIZONA_LDO1_CONTROL_1,
+ ARIZONA_LDO1_VSEL_MASK, val);
+}
+
+static int arizona_ldo1_hc_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct arizona_ldo1 *ldo = rdev_get_drvdata(rdev);
+ struct regmap *regmap = ldo->arizona->regmap;
+ unsigned int val;
+ int ret;
+
+ ret = regmap_read(regmap, ARIZONA_LDO1_CONTROL_2, &val);
+ if (ret != 0)
+ return ret;
+
+ if (val & ARIZONA_LDO1_HI_PWR)
+ return rdev->desc->n_voltages - 1;
+
+ ret = regmap_read(regmap, ARIZONA_LDO1_CONTROL_1, &val);
+ if (ret != 0)
+ return ret;
+
+ return (val & ARIZONA_LDO1_VSEL_MASK) >> ARIZONA_LDO1_VSEL_SHIFT;
+}
+
+static struct regulator_ops arizona_ldo1_hc_ops = {
+ .list_voltage = arizona_ldo1_hc_list_voltage,
+ .map_voltage = arizona_ldo1_hc_map_voltage,
+ .get_voltage_sel = arizona_ldo1_hc_get_voltage_sel,
+ .set_voltage_sel = arizona_ldo1_hc_set_voltage_sel,
+ .get_bypass = regulator_get_bypass_regmap,
+ .set_bypass = regulator_set_bypass_regmap,
+};
+
+static const struct regulator_desc arizona_ldo1_hc = {
+ .name = "LDO1",
+ .supply_name = "LDOVDD",
+ .type = REGULATOR_VOLTAGE,
+ .ops = &arizona_ldo1_hc_ops,
+
+ .bypass_reg = ARIZONA_LDO1_CONTROL_1,
+ .bypass_mask = ARIZONA_LDO1_BYPASS,
+ .min_uV = 900000,
+ .uV_step = 50000,
+ .n_voltages = 8,
+ .enable_time = 500,
+
+ .owner = THIS_MODULE,
+};
+
static struct regulator_ops arizona_ldo1_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
@@ -55,11 +157,22 @@ static const struct regulator_desc arizona_ldo1 = {
.bypass_mask = ARIZONA_LDO1_BYPASS,
.min_uV = 900000,
.uV_step = 50000,
- .n_voltages = 6,
+ .n_voltages = 7,
+ .enable_time = 500,
.owner = THIS_MODULE,
};
+static const struct regulator_init_data arizona_ldo1_dvfs = {
+ .constraints = {
+ .min_uV = 1200000,
+ .max_uV = 1800000,
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS |
+ REGULATOR_CHANGE_VOLTAGE,
+ },
+ .num_consumer_supplies = 1,
+};
+
static const struct regulator_init_data arizona_ldo1_default = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
@@ -70,6 +183,7 @@ static const struct regulator_init_data arizona_ldo1_default = {
static int arizona_ldo1_probe(struct platform_device *pdev)
{
struct arizona *arizona = dev_get_drvdata(pdev->dev.parent);
+ const struct regulator_desc *desc;
struct regulator_config config = { };
struct arizona_ldo1 *ldo1;
int ret;
@@ -87,7 +201,17 @@ static int arizona_ldo1_probe(struct platform_device *pdev)
* default init_data for it. This will be overridden with
* platform data if provided.
*/
- ldo1->init_data = arizona_ldo1_default;
+ switch (arizona->type) {
+ case WM5102:
+ desc = &arizona_ldo1_hc;
+ ldo1->init_data = arizona_ldo1_dvfs;
+ break;
+ default:
+ desc = &arizona_ldo1;
+ ldo1->init_data = arizona_ldo1_default;
+ break;
+ }
+
ldo1->init_data.consumer_supplies = &ldo1->supply;
ldo1->supply.supply = "DCVDD";
ldo1->supply.dev_name = dev_name(arizona->dev);
@@ -102,7 +226,7 @@ static int arizona_ldo1_probe(struct platform_device *pdev)
else
config.init_data = &ldo1->init_data;
- ldo1->regulator = regulator_register(&arizona_ldo1, &config);
+ ldo1->regulator = regulator_register(desc, &config);
if (IS_ERR(ldo1->regulator)) {
ret = PTR_ERR(ldo1->regulator);
dev_err(arizona->dev, "Failed to register LDO1 supply: %d\n",
diff --git a/drivers/regulator/arizona-micsupp.c b/drivers/regulator/arizona-micsupp.c
index 5ae2d3e794b..a6d040cbf8a 100644
--- a/drivers/regulator/arizona-micsupp.c
+++ b/drivers/regulator/arizona-micsupp.c
@@ -101,6 +101,8 @@ static const struct regulator_desc arizona_micsupp = {
.bypass_reg = ARIZONA_MIC_CHARGE_PUMP_1,
.bypass_mask = ARIZONA_CPMIC_BYPASS,
+ .enable_time = 3000,
+
.owner = THIS_MODULE,
};
diff --git a/drivers/regulator/as3711-regulator.c b/drivers/regulator/as3711-regulator.c
new file mode 100644
index 00000000000..2f1341db38a
--- /dev/null
+++ b/drivers/regulator/as3711-regulator.c
@@ -0,0 +1,369 @@
+/*
+ * AS3711 PMIC regulator driver, using DCDC Step Down and LDO supplies
+ *
+ * Copyright (C) 2012 Renesas Electronics Corporation
+ * Author: Guennadi Liakhovetski, <g.liakhovetski@gmx.de>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the version 2 of the GNU General Public License as
+ * published by the Free Software Foundation
+ */
+
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/mfd/as3711.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/slab.h>
+
+struct as3711_regulator_info {
+ struct regulator_desc desc;
+ unsigned int max_uV;
+};
+
+struct as3711_regulator {
+ struct as3711_regulator_info *reg_info;
+ struct regulator_dev *rdev;
+};
+
+static int as3711_list_voltage_sd(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ if (selector >= rdev->desc->n_voltages)
+ return -EINVAL;
+
+ if (!selector)
+ return 0;
+ if (selector < 0x41)
+ return 600000 + selector * 12500;
+ if (selector < 0x71)
+ return 1400000 + (selector - 0x40) * 25000;
+ return 2600000 + (selector - 0x70) * 50000;
+}
+
+static int as3711_list_voltage_aldo(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ if (selector >= rdev->desc->n_voltages)
+ return -EINVAL;
+
+ if (selector < 0x10)
+ return 1200000 + selector * 50000;
+ return 1800000 + (selector - 0x10) * 100000;
+}
+
+static int as3711_list_voltage_dldo(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ if (selector >= rdev->desc->n_voltages ||
+ (selector > 0x10 && selector < 0x20))
+ return -EINVAL;
+
+ if (selector < 0x11)
+ return 900000 + selector * 50000;
+ return 1750000 + (selector - 0x20) * 50000;
+}
+
+static int as3711_bound_check(struct regulator_dev *rdev,
+ int *min_uV, int *max_uV)
+{
+ struct as3711_regulator *reg = rdev_get_drvdata(rdev);
+ struct as3711_regulator_info *info = reg->reg_info;
+
+ dev_dbg(&rdev->dev, "%s(), %d, %d, %d\n", __func__,
+ *min_uV, rdev->desc->min_uV, info->max_uV);
+
+ if (*max_uV < *min_uV ||
+ *min_uV > info->max_uV || rdev->desc->min_uV > *max_uV)
+ return -EINVAL;
+
+ if (rdev->desc->n_voltages == 1)
+ return 0;
+
+ if (*max_uV > info->max_uV)
+ *max_uV = info->max_uV;
+
+ if (*min_uV < rdev->desc->min_uV)
+ *min_uV = rdev->desc->min_uV;
+
+ return *min_uV;
+}
+
+static int as3711_sel_check(int min, int max, int bottom, int step)
+{
+ int sel, voltage;
+
+ /* Round up min, when dividing: keeps us within the range */
+ sel = DIV_ROUND_UP(min - bottom, step);
+ voltage = sel * step + bottom;
+ pr_debug("%s(): select %d..%d in %d+N*%d: %d\n", __func__,
+ min, max, bottom, step, sel);
+ if (voltage > max)
+ return -EINVAL;
+
+ return sel;
+}
+
+static int as3711_map_voltage_sd(struct regulator_dev *rdev,
+ int min_uV, int max_uV)
+{
+ int ret;
+
+ ret = as3711_bound_check(rdev, &min_uV, &max_uV);
+ if (ret <= 0)
+ return ret;
+
+ if (min_uV <= 1400000)
+ return as3711_sel_check(min_uV, max_uV, 600000, 12500);
+
+ if (min_uV <= 2600000)
+ return as3711_sel_check(min_uV, max_uV, 1400000, 25000) + 0x40;
+
+ return as3711_sel_check(min_uV, max_uV, 2600000, 50000) + 0x70;
+}
+
+/*
+ * The regulator API supports 4 modes of operataion: FAST, NORMAL, IDLE and
+ * STANDBY. We map them in the following way to AS3711 SD1-4 DCDC modes:
+ * FAST: sdX_fast=1
+ * NORMAL: low_noise=1
+ * IDLE: low_noise=0
+ */
+
+static int as3711_set_mode_sd(struct regulator_dev *rdev, unsigned int mode)
+{
+ unsigned int fast_bit = rdev->desc->enable_mask,
+ low_noise_bit = fast_bit << 4;
+ u8 val;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ val = fast_bit | low_noise_bit;
+ break;
+ case REGULATOR_MODE_NORMAL:
+ val = low_noise_bit;
+ break;
+ case REGULATOR_MODE_IDLE:
+ val = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(rdev->regmap, AS3711_SD_CONTROL_1,
+ low_noise_bit | fast_bit, val);
+}
+
+static unsigned int as3711_get_mode_sd(struct regulator_dev *rdev)
+{
+ unsigned int fast_bit = rdev->desc->enable_mask,
+ low_noise_bit = fast_bit << 4, mask = fast_bit | low_noise_bit;
+ unsigned int val;
+ int ret = regmap_read(rdev->regmap, AS3711_SD_CONTROL_1, &val);
+
+ if (ret < 0)
+ return ret;
+
+ if ((val & mask) == mask)
+ return REGULATOR_MODE_FAST;
+
+ if ((val & mask) == low_noise_bit)
+ return REGULATOR_MODE_NORMAL;
+
+ if (!(val & mask))
+ return REGULATOR_MODE_IDLE;
+
+ return -EINVAL;
+}
+
+static int as3711_map_voltage_aldo(struct regulator_dev *rdev,
+ int min_uV, int max_uV)
+{
+ int ret;
+
+ ret = as3711_bound_check(rdev, &min_uV, &max_uV);
+ if (ret <= 0)
+ return ret;
+
+ if (min_uV <= 1800000)
+ return as3711_sel_check(min_uV, max_uV, 1200000, 50000);
+
+ return as3711_sel_check(min_uV, max_uV, 1800000, 100000) + 0x10;
+}
+
+static int as3711_map_voltage_dldo(struct regulator_dev *rdev,
+ int min_uV, int max_uV)
+{
+ int ret;
+
+ ret = as3711_bound_check(rdev, &min_uV, &max_uV);
+ if (ret <= 0)
+ return ret;
+
+ if (min_uV <= 1700000)
+ return as3711_sel_check(min_uV, max_uV, 900000, 50000);
+
+ return as3711_sel_check(min_uV, max_uV, 1750000, 50000) + 0x20;
+}
+
+static struct regulator_ops as3711_sd_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .list_voltage = as3711_list_voltage_sd,
+ .map_voltage = as3711_map_voltage_sd,
+ .get_mode = as3711_get_mode_sd,
+ .set_mode = as3711_set_mode_sd,
+};
+
+static struct regulator_ops as3711_aldo_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .list_voltage = as3711_list_voltage_aldo,
+ .map_voltage = as3711_map_voltage_aldo,
+};
+
+static struct regulator_ops as3711_dldo_ops = {
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .list_voltage = as3711_list_voltage_dldo,
+ .map_voltage = as3711_map_voltage_dldo,
+};
+
+#define AS3711_REG(_id, _en_reg, _en_bit, _vmask, _vshift, _min_uV, _max_uV, _sfx) \
+ [AS3711_REGULATOR_ ## _id] = { \
+ .desc = { \
+ .name = "as3711-regulator-" # _id, \
+ .id = AS3711_REGULATOR_ ## _id, \
+ .n_voltages = (_vmask + 1), \
+ .ops = &as3711_ ## _sfx ## _ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .vsel_reg = AS3711_ ## _id ## _VOLTAGE, \
+ .vsel_mask = _vmask << _vshift, \
+ .enable_reg = AS3711_ ## _en_reg, \
+ .enable_mask = BIT(_en_bit), \
+ .min_uV = _min_uV, \
+ }, \
+ .max_uV = _max_uV, \
+}
+
+static struct as3711_regulator_info as3711_reg_info[] = {
+ AS3711_REG(SD_1, SD_CONTROL, 0, 0x7f, 0, 612500, 3350000, sd),
+ AS3711_REG(SD_2, SD_CONTROL, 1, 0x7f, 0, 612500, 3350000, sd),
+ AS3711_REG(SD_3, SD_CONTROL, 2, 0x7f, 0, 612500, 3350000, sd),
+ AS3711_REG(SD_4, SD_CONTROL, 3, 0x7f, 0, 612500, 3350000, sd),
+ AS3711_REG(LDO_1, LDO_1_VOLTAGE, 7, 0x1f, 0, 1200000, 3300000, aldo),
+ AS3711_REG(LDO_2, LDO_2_VOLTAGE, 7, 0x1f, 0, 1200000, 3300000, aldo),
+ AS3711_REG(LDO_3, LDO_3_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo),
+ AS3711_REG(LDO_4, LDO_4_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo),
+ AS3711_REG(LDO_5, LDO_5_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo),
+ AS3711_REG(LDO_6, LDO_6_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo),
+ AS3711_REG(LDO_7, LDO_7_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo),
+ AS3711_REG(LDO_8, LDO_8_VOLTAGE, 7, 0x3f, 0, 900000, 3300000, dldo),
+ /* StepUp output voltage depends on supplying regulator */
+};
+
+#define AS3711_REGULATOR_NUM ARRAY_SIZE(as3711_reg_info)
+
+static int as3711_regulator_probe(struct platform_device *pdev)
+{
+ struct as3711_regulator_pdata *pdata = dev_get_platdata(&pdev->dev);
+ struct as3711 *as3711 = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_init_data *reg_data;
+ struct regulator_config config = {.dev = &pdev->dev,};
+ struct as3711_regulator *reg = NULL;
+ struct as3711_regulator *regs;
+ struct regulator_dev *rdev;
+ struct as3711_regulator_info *ri;
+ int ret;
+ int id;
+
+ if (!pdata)
+ dev_dbg(&pdev->dev, "No platform data...\n");
+
+ regs = devm_kzalloc(&pdev->dev, AS3711_REGULATOR_NUM *
+ sizeof(struct as3711_regulator), GFP_KERNEL);
+ if (!regs) {
+ dev_err(&pdev->dev, "Memory allocation failed exiting..\n");
+ return -ENOMEM;
+ }
+
+ for (id = 0, ri = as3711_reg_info; id < AS3711_REGULATOR_NUM; ++id, ri++) {
+ reg_data = pdata ? pdata->init_data[id] : NULL;
+
+ /* No need to register if there is no regulator data */
+ if (!ri->desc.name)
+ continue;
+
+ reg = &regs[id];
+ reg->reg_info = ri;
+
+ config.init_data = reg_data;
+ config.driver_data = reg;
+ config.regmap = as3711->regmap;
+
+ rdev = regulator_register(&ri->desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "Failed to register regulator %s\n",
+ ri->desc.name);
+ ret = PTR_ERR(rdev);
+ goto eregreg;
+ }
+ reg->rdev = rdev;
+ }
+ platform_set_drvdata(pdev, regs);
+ return 0;
+
+eregreg:
+ while (--id >= 0)
+ regulator_unregister(regs[id].rdev);
+
+ return ret;
+}
+
+static int as3711_regulator_remove(struct platform_device *pdev)
+{
+ struct as3711_regulator *regs = platform_get_drvdata(pdev);
+ int id;
+
+ for (id = 0; id < AS3711_REGULATOR_NUM; ++id)
+ regulator_unregister(regs[id].rdev);
+ return 0;
+}
+
+static struct platform_driver as3711_regulator_driver = {
+ .driver = {
+ .name = "as3711-regulator",
+ .owner = THIS_MODULE,
+ },
+ .probe = as3711_regulator_probe,
+ .remove = as3711_regulator_remove,
+};
+
+static int __init as3711_regulator_init(void)
+{
+ return platform_driver_register(&as3711_regulator_driver);
+}
+subsys_initcall(as3711_regulator_init);
+
+static void __exit as3711_regulator_exit(void)
+{
+ platform_driver_unregister(&as3711_regulator_driver);
+}
+module_exit(as3711_regulator_exit);
+
+MODULE_AUTHOR("Guennadi Liakhovetski <g.liakhovetski@gmx.de>");
+MODULE_DESCRIPTION("AS3711 regulator driver");
+MODULE_ALIAS("platform:as3711-regulator");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index 3db1e011d22..35c149bb2ad 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -199,8 +199,11 @@ static int regulator_check_consumers(struct regulator_dev *rdev,
*min_uV = regulator->min_uV;
}
- if (*min_uV > *max_uV)
+ if (*min_uV > *max_uV) {
+ dev_err(regulator->dev, "Restricting voltage, %u-%uuV\n",
+ regulator->min_uV, regulator->max_uV);
return -EINVAL;
+ }
return 0;
}
@@ -880,7 +883,9 @@ static int machine_constraints_voltage(struct regulator_dev *rdev,
/* final: [min_uV..max_uV] valid iff constraints valid */
if (max_uV < min_uV) {
- rdev_err(rdev, "unsupportable voltage constraints\n");
+ rdev_err(rdev,
+ "unsupportable voltage constraints %u-%uuV\n",
+ min_uV, max_uV);
return -EINVAL;
}
@@ -1867,6 +1872,28 @@ int regulator_is_enabled(struct regulator *regulator)
EXPORT_SYMBOL_GPL(regulator_is_enabled);
/**
+ * regulator_can_change_voltage - check if regulator can change voltage
+ * @regulator: regulator source
+ *
+ * Returns positive if the regulator driver backing the source/client
+ * can change its voltage, false otherwise. Usefull for detecting fixed
+ * or dummy regulators and disabling voltage change logic in the client
+ * driver.
+ */
+int regulator_can_change_voltage(struct regulator *regulator)
+{
+ struct regulator_dev *rdev = regulator->rdev;
+
+ if (rdev->constraints &&
+ rdev->constraints->valid_ops_mask & REGULATOR_CHANGE_VOLTAGE &&
+ rdev->desc->n_voltages > 1)
+ return 1;
+
+ return 0;
+}
+EXPORT_SYMBOL_GPL(regulator_can_change_voltage);
+
+/**
* regulator_count_voltages - count regulator_list_voltage() selectors
* @regulator: regulator source
*
diff --git a/drivers/regulator/da9052-regulator.c b/drivers/regulator/da9052-regulator.c
index d6fbfd3dced..d0963090442 100644
--- a/drivers/regulator/da9052-regulator.c
+++ b/drivers/regulator/da9052-regulator.c
@@ -129,17 +129,17 @@ static int da9052_dcdc_set_current_limit(struct regulator_dev *rdev, int min_uA,
else if (offset == 0)
row = 1;
- if (min_uA > da9052_current_limits[row][DA9052_MAX_UA] ||
- max_uA < da9052_current_limits[row][DA9052_MIN_UA])
- return -EINVAL;
-
for (i = DA9052_CURRENT_RANGE - 1; i >= 0; i--) {
- if (da9052_current_limits[row][i] <= max_uA) {
+ if ((min_uA <= da9052_current_limits[row][i]) &&
+ (da9052_current_limits[row][i] <= max_uA)) {
reg_val = i;
break;
}
}
+ if (i < 0)
+ return -EINVAL;
+
/* Determine the even or odd position of the buck current limit
* register field
*/
diff --git a/drivers/regulator/da9055-regulator.c b/drivers/regulator/da9055-regulator.c
new file mode 100644
index 00000000000..db59ce7534c
--- /dev/null
+++ b/drivers/regulator/da9055-regulator.c
@@ -0,0 +1,680 @@
+/*
+* Regulator driver for DA9055 PMIC
+*
+* Copyright(c) 2012 Dialog Semiconductor Ltd.
+*
+* Author: David Dajun Chen <dchen@diasemi.com>
+*
+* This program is free software; you can redistribute it and/or modify
+* it under the terms of the GNU General Public License as published by
+* the Free Software Foundation; either version 2 of the License, or
+* (at your option) any later version.
+*
+*/
+
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+#include <linux/mfd/da9055/core.h>
+#include <linux/mfd/da9055/reg.h>
+#include <linux/mfd/da9055/pdata.h>
+
+#define DA9055_MIN_UA 0
+#define DA9055_MAX_UA 3
+
+#define DA9055_LDO_MODE_SYNC 0
+#define DA9055_LDO_MODE_SLEEP 1
+
+#define DA9055_BUCK_MODE_SLEEP 1
+#define DA9055_BUCK_MODE_SYNC 2
+#define DA9055_BUCK_MODE_AUTO 3
+
+/* DA9055 REGULATOR IDs */
+#define DA9055_ID_BUCK1 0
+#define DA9055_ID_BUCK2 1
+#define DA9055_ID_LDO1 2
+#define DA9055_ID_LDO2 3
+#define DA9055_ID_LDO3 4
+#define DA9055_ID_LDO4 5
+#define DA9055_ID_LDO5 6
+#define DA9055_ID_LDO6 7
+
+/* DA9055 BUCK current limit */
+static const int da9055_current_limits[] = { 500000, 600000, 700000, 800000 };
+
+struct da9055_conf_reg {
+ int reg;
+ int sel_mask;
+ int en_mask;
+};
+
+struct da9055_volt_reg {
+ int reg_a;
+ int reg_b;
+ int sl_shift;
+ int v_offset;
+ int v_mask;
+ int v_shift;
+};
+
+struct da9055_mode_reg {
+ int reg;
+ int mask;
+ int shift;
+};
+
+struct da9055_regulator_info {
+ struct regulator_desc reg_desc;
+ struct da9055_conf_reg conf;
+ struct da9055_volt_reg volt;
+ struct da9055_mode_reg mode;
+};
+
+struct da9055_regulator {
+ struct da9055 *da9055;
+ struct da9055_regulator_info *info;
+ struct regulator_dev *rdev;
+ enum gpio_select reg_rselect;
+};
+
+static unsigned int da9055_buck_get_mode(struct regulator_dev *rdev)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int ret, mode = 0;
+
+ ret = da9055_reg_read(regulator->da9055, info->mode.reg);
+ if (ret < 0)
+ return ret;
+
+ switch ((ret & info->mode.mask) >> info->mode.shift) {
+ case DA9055_BUCK_MODE_SYNC:
+ mode = REGULATOR_MODE_FAST;
+ break;
+ case DA9055_BUCK_MODE_AUTO:
+ mode = REGULATOR_MODE_NORMAL;
+ break;
+ case DA9055_BUCK_MODE_SLEEP:
+ mode = REGULATOR_MODE_STANDBY;
+ break;
+ }
+
+ return mode;
+}
+
+static int da9055_buck_set_mode(struct regulator_dev *rdev,
+ unsigned int mode)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int val = 0;
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ val = DA9055_BUCK_MODE_SYNC << info->mode.shift;
+ break;
+ case REGULATOR_MODE_NORMAL:
+ val = DA9055_BUCK_MODE_AUTO << info->mode.shift;
+ break;
+ case REGULATOR_MODE_STANDBY:
+ val = DA9055_BUCK_MODE_SLEEP << info->mode.shift;
+ break;
+ }
+
+ return da9055_reg_update(regulator->da9055, info->mode.reg,
+ info->mode.mask, val);
+}
+
+static unsigned int da9055_ldo_get_mode(struct regulator_dev *rdev)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int ret;
+
+ ret = da9055_reg_read(regulator->da9055, info->volt.reg_b);
+ if (ret < 0)
+ return ret;
+
+ if (ret >> info->volt.sl_shift)
+ return REGULATOR_MODE_STANDBY;
+ else
+ return REGULATOR_MODE_NORMAL;
+}
+
+static int da9055_ldo_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ struct da9055_volt_reg volt = info->volt;
+ int val = 0;
+
+ switch (mode) {
+ case REGULATOR_MODE_NORMAL:
+ case REGULATOR_MODE_FAST:
+ val = DA9055_LDO_MODE_SYNC;
+ break;
+ case REGULATOR_MODE_STANDBY:
+ val = DA9055_LDO_MODE_SLEEP;
+ break;
+ }
+
+ return da9055_reg_update(regulator->da9055, volt.reg_b,
+ 1 << volt.sl_shift,
+ val << volt.sl_shift);
+}
+
+static int da9055_buck_get_current_limit(struct regulator_dev *rdev)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int ret;
+
+ ret = da9055_reg_read(regulator->da9055, DA9055_REG_BUCK_LIM);
+ if (ret < 0)
+ return ret;
+
+ ret &= info->mode.mask;
+ return da9055_current_limits[ret >> info->mode.shift];
+}
+
+static int da9055_buck_set_current_limit(struct regulator_dev *rdev, int min_uA,
+ int max_uA)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int i;
+
+ for (i = ARRAY_SIZE(da9055_current_limits) - 1; i >= 0; i--) {
+ if ((min_uA <= da9055_current_limits[i]) &&
+ (da9055_current_limits[i] <= max_uA))
+ return da9055_reg_update(regulator->da9055,
+ DA9055_REG_BUCK_LIM,
+ info->mode.mask,
+ i << info->mode.shift);
+ }
+
+ return -EINVAL;
+}
+
+static int da9055_list_voltage(struct regulator_dev *rdev, unsigned selector)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+
+ if (selector >= rdev->desc->n_voltages)
+ return -EINVAL;
+
+ if (selector < info->volt.v_offset)
+ return 0;
+
+ selector -= info->volt.v_offset;
+ return rdev->desc->min_uV + (rdev->desc->uV_step * selector);
+}
+
+static int da9055_map_voltage(struct regulator_dev *rdev, int min_uV,
+ int max_uV)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int sel, voltage;
+
+ if (min_uV < rdev->desc->min_uV)
+ min_uV = rdev->desc->min_uV;
+
+ sel = DIV_ROUND_UP(min_uV - rdev->desc->min_uV, rdev->desc->uV_step);
+ sel += info->volt.v_offset;
+
+ voltage = da9055_list_voltage(rdev, sel);
+ if (voltage < min_uV || voltage > max_uV)
+ return -EINVAL;
+
+ return sel;
+}
+
+static int da9055_regulator_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ struct da9055_volt_reg volt = info->volt;
+ int ret, sel;
+
+ /*
+ * There are two voltage register set A & B for voltage ramping but
+ * either one of then can be active therefore we first determine
+ * the active register set.
+ */
+ ret = da9055_reg_read(regulator->da9055, info->conf.reg);
+ if (ret < 0)
+ return ret;
+
+ ret &= info->conf.sel_mask;
+
+ /* Get the voltage for the active register set A/B */
+ if (ret == DA9055_REGUALTOR_SET_A)
+ ret = da9055_reg_read(regulator->da9055, volt.reg_a);
+ else
+ ret = da9055_reg_read(regulator->da9055, volt.reg_b);
+
+ if (ret < 0)
+ return ret;
+
+ sel = (ret & volt.v_mask);
+ if (sel <= volt.v_offset)
+ return 0;
+ else
+ return sel;
+}
+
+static int da9055_regulator_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned int selector)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int ret;
+
+ /*
+ * Regulator register set A/B is not selected through GPIO therefore
+ * we use default register set A for voltage ramping.
+ */
+ if (regulator->reg_rselect == NO_GPIO) {
+ /* Select register set A */
+ ret = da9055_reg_update(regulator->da9055, info->conf.reg,
+ info->conf.sel_mask, DA9055_SEL_REG_A);
+ if (ret < 0)
+ return ret;
+
+ /* Set the voltage */
+ return da9055_reg_update(regulator->da9055, info->volt.reg_a,
+ info->volt.v_mask, selector);
+ }
+
+ /*
+ * Here regulator register set A/B is selected through GPIO.
+ * Therefore we first determine the selected register set A/B and
+ * then set the desired voltage for that register set A/B.
+ */
+ ret = da9055_reg_read(regulator->da9055, info->conf.reg);
+ if (ret < 0)
+ return ret;
+
+ ret &= info->conf.sel_mask;
+
+ /* Set the voltage */
+ if (ret == DA9055_REGUALTOR_SET_A)
+ return da9055_reg_update(regulator->da9055, info->volt.reg_a,
+ info->volt.v_mask, selector);
+ else
+ return da9055_reg_update(regulator->da9055, info->volt.reg_b,
+ info->volt.v_mask, selector);
+}
+
+static int da9055_regulator_set_suspend_voltage(struct regulator_dev *rdev,
+ int uV)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+ int ret;
+
+ /* Select register set B for suspend voltage ramping. */
+ if (regulator->reg_rselect == NO_GPIO) {
+ ret = da9055_reg_update(regulator->da9055, info->conf.reg,
+ info->conf.sel_mask, DA9055_SEL_REG_B);
+ if (ret < 0)
+ return ret;
+ }
+
+ ret = da9055_map_voltage(rdev, uV, uV);
+ if (ret < 0)
+ return ret;
+
+ return da9055_reg_update(regulator->da9055, info->volt.reg_b,
+ info->volt.v_mask, ret);
+}
+
+static int da9055_suspend_enable(struct regulator_dev *rdev)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+
+ /* Select register set B for voltage ramping. */
+ if (regulator->reg_rselect == NO_GPIO)
+ return da9055_reg_update(regulator->da9055, info->conf.reg,
+ info->conf.sel_mask, DA9055_SEL_REG_B);
+ else
+ return 0;
+}
+
+static int da9055_suspend_disable(struct regulator_dev *rdev)
+{
+ struct da9055_regulator *regulator = rdev_get_drvdata(rdev);
+ struct da9055_regulator_info *info = regulator->info;
+
+ /* Diselect register set B. */
+ if (regulator->reg_rselect == NO_GPIO)
+ return da9055_reg_update(regulator->da9055, info->conf.reg,
+ info->conf.sel_mask, DA9055_SEL_REG_A);
+ else
+ return 0;
+}
+
+static struct regulator_ops da9055_buck_ops = {
+ .get_mode = da9055_buck_get_mode,
+ .set_mode = da9055_buck_set_mode,
+
+ .get_current_limit = da9055_buck_get_current_limit,
+ .set_current_limit = da9055_buck_set_current_limit,
+
+ .get_voltage_sel = da9055_regulator_get_voltage_sel,
+ .set_voltage_sel = da9055_regulator_set_voltage_sel,
+ .list_voltage = da9055_list_voltage,
+ .map_voltage = da9055_map_voltage,
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+
+ .set_suspend_voltage = da9055_regulator_set_suspend_voltage,
+ .set_suspend_enable = da9055_suspend_enable,
+ .set_suspend_disable = da9055_suspend_disable,
+ .set_suspend_mode = da9055_buck_set_mode,
+};
+
+static struct regulator_ops da9055_ldo_ops = {
+ .get_mode = da9055_ldo_get_mode,
+ .set_mode = da9055_ldo_set_mode,
+
+ .get_voltage_sel = da9055_regulator_get_voltage_sel,
+ .set_voltage_sel = da9055_regulator_set_voltage_sel,
+ .list_voltage = da9055_list_voltage,
+ .map_voltage = da9055_map_voltage,
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+
+ .set_suspend_voltage = da9055_regulator_set_suspend_voltage,
+ .set_suspend_enable = da9055_suspend_enable,
+ .set_suspend_disable = da9055_suspend_disable,
+ .set_suspend_mode = da9055_ldo_set_mode,
+
+};
+
+#define DA9055_LDO(_id, step, min, max, vbits, voffset) \
+{\
+ .reg_desc = {\
+ .name = #_id,\
+ .ops = &da9055_ldo_ops,\
+ .type = REGULATOR_VOLTAGE,\
+ .id = DA9055_ID_##_id,\
+ .n_voltages = (max - min) / step + 1 + (voffset), \
+ .enable_reg = DA9055_REG_BCORE_CONT + DA9055_ID_##_id, \
+ .enable_mask = 1, \
+ .min_uV = (min) * 1000,\
+ .uV_step = (step) * 1000,\
+ .owner = THIS_MODULE,\
+ },\
+ .conf = {\
+ .reg = DA9055_REG_BCORE_CONT + DA9055_ID_##_id, \
+ .sel_mask = (1 << 4),\
+ .en_mask = 1,\
+ },\
+ .volt = {\
+ .reg_a = DA9055_REG_VBCORE_A + DA9055_ID_##_id, \
+ .reg_b = DA9055_REG_VBCORE_B + DA9055_ID_##_id, \
+ .sl_shift = 7,\
+ .v_offset = (voffset),\
+ .v_mask = (1 << (vbits)) - 1,\
+ .v_shift = (vbits),\
+ },\
+}
+
+#define DA9055_BUCK(_id, step, min, max, vbits, voffset, mbits, sbits) \
+{\
+ .reg_desc = {\
+ .name = #_id,\
+ .ops = &da9055_buck_ops,\
+ .type = REGULATOR_VOLTAGE,\
+ .id = DA9055_ID_##_id,\
+ .n_voltages = (max - min) / step + 1 + (voffset), \
+ .enable_reg = DA9055_REG_BCORE_CONT + DA9055_ID_##_id, \
+ .enable_mask = 1,\
+ .min_uV = (min) * 1000,\
+ .uV_step = (step) * 1000,\
+ .owner = THIS_MODULE,\
+ },\
+ .conf = {\
+ .reg = DA9055_REG_BCORE_CONT + DA9055_ID_##_id, \
+ .sel_mask = (1 << 4),\
+ .en_mask = 1,\
+ },\
+ .volt = {\
+ .reg_a = DA9055_REG_VBCORE_A + DA9055_ID_##_id, \
+ .reg_b = DA9055_REG_VBCORE_B + DA9055_ID_##_id, \
+ .sl_shift = 7,\
+ .v_offset = (voffset),\
+ .v_mask = (1 << (vbits)) - 1,\
+ .v_shift = (vbits),\
+ },\
+ .mode = {\
+ .reg = DA9055_REG_BCORE_MODE,\
+ .mask = (mbits),\
+ .shift = (sbits),\
+ },\
+}
+
+static struct da9055_regulator_info da9055_regulator_info[] = {
+ DA9055_BUCK(BUCK1, 25, 725, 2075, 6, 9, 0xc, 2),
+ DA9055_BUCK(BUCK2, 25, 925, 2500, 6, 0, 3, 0),
+ DA9055_LDO(LDO1, 50, 900, 3300, 6, 2),
+ DA9055_LDO(LDO2, 50, 900, 3300, 6, 3),
+ DA9055_LDO(LDO3, 50, 900, 3300, 6, 2),
+ DA9055_LDO(LDO4, 50, 900, 3300, 6, 2),
+ DA9055_LDO(LDO5, 50, 900, 2750, 6, 2),
+ DA9055_LDO(LDO6, 20, 900, 3300, 7, 0),
+};
+
+/*
+ * Configures regulator to be controlled either through GPIO 1 or 2.
+ * GPIO can control regulator state and/or select the regulator register
+ * set A/B for voltage ramping.
+ */
+static __devinit int da9055_gpio_init(struct da9055_regulator *regulator,
+ struct regulator_config *config,
+ struct da9055_pdata *pdata, int id)
+{
+ struct da9055_regulator_info *info = regulator->info;
+ int ret = 0;
+
+ if (pdata->gpio_ren && pdata->gpio_ren[id]) {
+ char name[18];
+ int gpio_mux = pdata->gpio_ren[id];
+
+ config->ena_gpio = pdata->ena_gpio[id];
+ config->ena_gpio_flags = GPIOF_OUT_INIT_HIGH;
+ config->ena_gpio_invert = 1;
+
+ /*
+ * GPI pin is muxed with regulator to control the
+ * regulator state.
+ */
+ sprintf(name, "DA9055 GPI %d", gpio_mux);
+ ret = devm_gpio_request_one(config->dev, gpio_mux, GPIOF_DIR_IN,
+ name);
+ if (ret < 0)
+ goto err;
+
+ /*
+ * Let the regulator know that its state is controlled
+ * through GPI.
+ */
+ ret = da9055_reg_update(regulator->da9055, info->conf.reg,
+ DA9055_E_GPI_MASK,
+ pdata->reg_ren[id]
+ << DA9055_E_GPI_SHIFT);
+ if (ret < 0)
+ goto err;
+ }
+
+ if (pdata->gpio_rsel && pdata->gpio_rsel[id]) {
+ char name[18];
+ int gpio_mux = pdata->gpio_rsel[id];
+
+ regulator->reg_rselect = pdata->reg_rsel[id];
+
+ /*
+ * GPI pin is muxed with regulator to select the
+ * regulator register set A/B for voltage ramping.
+ */
+ sprintf(name, "DA9055 GPI %d", gpio_mux);
+ ret = devm_gpio_request_one(config->dev, gpio_mux, GPIOF_DIR_IN,
+ name);
+ if (ret < 0)
+ goto err;
+
+ /*
+ * Let the regulator know that its register set A/B
+ * will be selected through GPI for voltage ramping.
+ */
+ ret = da9055_reg_update(regulator->da9055, info->conf.reg,
+ DA9055_V_GPI_MASK,
+ pdata->reg_rsel[id]
+ << DA9055_V_GPI_SHIFT);
+ }
+
+err:
+ return ret;
+}
+
+static irqreturn_t da9055_ldo5_6_oc_irq(int irq, void *data)
+{
+ struct da9055_regulator *regulator = data;
+
+ regulator_notifier_call_chain(regulator->rdev,
+ REGULATOR_EVENT_OVER_CURRENT, NULL);
+
+ return IRQ_HANDLED;
+}
+
+static inline struct da9055_regulator_info *find_regulator_info(int id)
+{
+ struct da9055_regulator_info *info;
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(da9055_regulator_info); i++) {
+ info = &da9055_regulator_info[i];
+ if (info->reg_desc.id == id)
+ return info;
+ }
+
+ return NULL;
+}
+
+static int __devinit da9055_regulator_probe(struct platform_device *pdev)
+{
+ struct regulator_config config = { };
+ struct da9055_regulator *regulator;
+ struct da9055 *da9055 = dev_get_drvdata(pdev->dev.parent);
+ struct da9055_pdata *pdata = da9055->dev->platform_data;
+ int ret, irq;
+
+ if (pdata == NULL || pdata->regulators[pdev->id] == NULL)
+ return -ENODEV;
+
+ regulator = devm_kzalloc(&pdev->dev, sizeof(struct da9055_regulator),
+ GFP_KERNEL);
+ if (!regulator)
+ return -ENOMEM;
+
+ regulator->info = find_regulator_info(pdev->id);
+ if (regulator->info == NULL) {
+ dev_err(&pdev->dev, "invalid regulator ID specified\n");
+ return -EINVAL;
+ }
+
+ regulator->da9055 = da9055;
+ config.dev = &pdev->dev;
+ config.driver_data = regulator;
+ config.regmap = da9055->regmap;
+
+ if (pdata && pdata->regulators)
+ config.init_data = pdata->regulators[pdev->id];
+
+ ret = da9055_gpio_init(regulator, &config, pdata, pdev->id);
+ if (ret < 0)
+ return ret;
+
+ regulator->rdev = regulator_register(&regulator->info->reg_desc,
+ &config);
+ if (IS_ERR(regulator->rdev)) {
+ dev_err(&pdev->dev, "Failed to register regulator %s\n",
+ regulator->info->reg_desc.name);
+ ret = PTR_ERR(regulator->rdev);
+ return ret;
+ }
+
+ /* Only LDO 5 and 6 has got the over current interrupt */
+ if (pdev->id == DA9055_ID_LDO5 || pdev->id == DA9055_ID_LDO6) {
+ irq = platform_get_irq_byname(pdev, "REGULATOR");
+ irq = regmap_irq_get_virq(da9055->irq_data, irq);
+ ret = devm_request_threaded_irq(&pdev->dev, irq, NULL,
+ da9055_ldo5_6_oc_irq,
+ IRQF_TRIGGER_HIGH |
+ IRQF_ONESHOT |
+ IRQF_PROBE_SHARED,
+ pdev->name, regulator);
+ if (ret != 0) {
+ if (ret != -EBUSY) {
+ dev_err(&pdev->dev,
+ "Failed to request Regulator IRQ %d: %d\n",
+ irq, ret);
+ goto err_regulator;
+ }
+ }
+ }
+
+ platform_set_drvdata(pdev, regulator);
+
+ return 0;
+
+err_regulator:
+ regulator_unregister(regulator->rdev);
+ return ret;
+}
+
+static int __devexit da9055_regulator_remove(struct platform_device *pdev)
+{
+ struct da9055_regulator *regulator = platform_get_drvdata(pdev);
+
+ regulator_unregister(regulator->rdev);
+
+ return 0;
+}
+
+static struct platform_driver da9055_regulator_driver = {
+ .probe = da9055_regulator_probe,
+ .remove = __devexit_p(da9055_regulator_remove),
+ .driver = {
+ .name = "da9055-regulator",
+ .owner = THIS_MODULE,
+ },
+};
+
+static int __init da9055_regulator_init(void)
+{
+ return platform_driver_register(&da9055_regulator_driver);
+}
+subsys_initcall(da9055_regulator_init);
+
+static void __exit da9055_regulator_exit(void)
+{
+ platform_driver_unregister(&da9055_regulator_driver);
+}
+module_exit(da9055_regulator_exit);
+
+MODULE_AUTHOR("David Dajun Chen <dchen@diasemi.com>");
+MODULE_DESCRIPTION("Power Regulator driver for Dialog DA9055 PMIC");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:da9055-regulator");
diff --git a/drivers/regulator/gpio-regulator.c b/drivers/regulator/gpio-regulator.c
index 3ee79c83ae5..2cfd9d3079e 100644
--- a/drivers/regulator/gpio-regulator.c
+++ b/drivers/regulator/gpio-regulator.c
@@ -364,10 +364,12 @@ static int gpio_regulator_remove(struct platform_device *pdev)
return 0;
}
+#if defined(CONFIG_OF)
static const struct of_device_id regulator_gpio_of_match[] __devinitconst = {
{ .compatible = "regulator-gpio", },
{},
};
+#endif
static struct platform_driver gpio_regulator_driver = {
.probe = gpio_regulator_probe,
@@ -375,7 +377,7 @@ static struct platform_driver gpio_regulator_driver = {
.driver = {
.name = "gpio-regulator",
.owner = THIS_MODULE,
- .of_match_table = regulator_gpio_of_match,
+ .of_match_table = of_match_ptr(regulator_gpio_of_match),
},
};
diff --git a/drivers/regulator/lp8788-buck.c b/drivers/regulator/lp8788-buck.c
index 6cc02c35ddb..aef3f2b0c5e 100644
--- a/drivers/regulator/lp8788-buck.c
+++ b/drivers/regulator/lp8788-buck.c
@@ -429,18 +429,6 @@ static struct regulator_desc lp8788_buck_desc[] = {
},
};
-static int _gpio_request(struct lp8788_buck *buck, int gpio, char *name)
-{
- struct device *dev = buck->lp->dev;
-
- if (!gpio_is_valid(gpio)) {
- dev_err(dev, "invalid gpio: %d\n", gpio);
- return -EINVAL;
- }
-
- return devm_gpio_request_one(dev, gpio, DVS_LOW, name);
-}
-
static int lp8788_dvs_gpio_request(struct lp8788_buck *buck,
enum lp8788_buck_id id)
{
@@ -452,7 +440,8 @@ static int lp8788_dvs_gpio_request(struct lp8788_buck *buck,
switch (id) {
case BUCK1:
gpio = pdata->buck1_dvs->gpio;
- ret = _gpio_request(buck, gpio, b1_name);
+ ret = devm_gpio_request_one(buck->lp->dev, gpio, DVS_LOW,
+ b1_name);
if (ret)
return ret;
@@ -461,7 +450,8 @@ static int lp8788_dvs_gpio_request(struct lp8788_buck *buck,
case BUCK2:
for (i = 0 ; i < LP8788_NUM_BUCK2_DVS ; i++) {
gpio = pdata->buck2_dvs->gpio[i];
- ret = _gpio_request(buck, gpio, b2_name[i]);
+ ret = devm_gpio_request_one(buck->lp->dev, gpio,
+ DVS_LOW, b2_name[i]);
if (ret)
return ret;
}
diff --git a/drivers/regulator/lp8788-ldo.c b/drivers/regulator/lp8788-ldo.c
index 26753a01378..3792741708c 100644
--- a/drivers/regulator/lp8788-ldo.c
+++ b/drivers/regulator/lp8788-ldo.c
@@ -126,7 +126,7 @@ struct lp8788_ldo {
};
/* DLDO 1, 2, 3, 9 voltage table */
-const int lp8788_dldo1239_vtbl[] = {
+static const int lp8788_dldo1239_vtbl[] = {
1800000, 1900000, 2000000, 2100000, 2200000, 2300000, 2400000, 2500000,
2600000, 2700000, 2800000, 2900000, 3000000, 2850000, 2850000, 2850000,
2850000, 2850000, 2850000, 2850000, 2850000, 2850000, 2850000, 2850000,
@@ -662,14 +662,6 @@ static int lp8788_config_ldo_enable_mode(struct lp8788_ldo *ldo,
[EN_DLDO7] = LP8788_EN_SEL_DLDO7_M,
[EN_DLDO911] = LP8788_EN_SEL_DLDO911_M,
};
- u8 val[] = {
- [EN_ALDO1] = 0 << 5,
- [EN_ALDO234] = 0 << 4,
- [EN_ALDO5] = 0 << 3,
- [EN_ALDO7] = 0 << 2,
- [EN_DLDO7] = 0 << 1,
- [EN_DLDO911] = 0 << 0,
- };
switch (id) {
case DLDO7:
@@ -708,8 +700,7 @@ static int lp8788_config_ldo_enable_mode(struct lp8788_ldo *ldo,
return ret;
set_default_ldo_enable_mode:
- return lp8788_update_bits(lp, LP8788_EN_SEL, en_mask[enable_id],
- val[enable_id]);
+ return lp8788_update_bits(lp, LP8788_EN_SEL, en_mask[enable_id], 0);
}
static int lp8788_dldo_probe(struct platform_device *pdev)
diff --git a/drivers/regulator/max1586.c b/drivers/regulator/max1586.c
index 3a035ece83c..8c5a54f541b 100644
--- a/drivers/regulator/max1586.c
+++ b/drivers/regulator/max1586.c
@@ -44,6 +44,9 @@ struct max1586_data {
unsigned int min_uV;
unsigned int max_uV;
+ unsigned int v3_curr_sel;
+ unsigned int v6_curr_sel;
+
struct regulator_dev *rdev[0];
};
@@ -63,31 +66,60 @@ static int v6_voltages_uv[] = { 1, 1800000, 2500000, 3000000 };
* R24 and R25=100kOhm as described in the data sheet.
* The gain is approximately: 1 + R24/R25 + R24/185.5kOhm
*/
+static int max1586_v3_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct max1586_data *max1586 = rdev_get_drvdata(rdev);
+
+ return max1586->v3_curr_sel;
+}
+
static int max1586_v3_set_voltage_sel(struct regulator_dev *rdev,
unsigned selector)
{
struct max1586_data *max1586 = rdev_get_drvdata(rdev);
struct i2c_client *client = max1586->client;
+ int ret;
u8 v3_prog;
dev_dbg(&client->dev, "changing voltage v3 to %dmv\n",
regulator_list_voltage_linear(rdev, selector) / 1000);
v3_prog = I2C_V3_SELECT | (u8) selector;
- return i2c_smbus_write_byte(client, v3_prog);
+ ret = i2c_smbus_write_byte(client, v3_prog);
+ if (ret)
+ return ret;
+
+ max1586->v3_curr_sel = selector;
+
+ return 0;
+}
+
+static int max1586_v6_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct max1586_data *max1586 = rdev_get_drvdata(rdev);
+
+ return max1586->v6_curr_sel;
}
static int max1586_v6_set_voltage_sel(struct regulator_dev *rdev,
unsigned int selector)
{
- struct i2c_client *client = rdev_get_drvdata(rdev);
+ struct max1586_data *max1586 = rdev_get_drvdata(rdev);
+ struct i2c_client *client = max1586->client;
u8 v6_prog;
+ int ret;
dev_dbg(&client->dev, "changing voltage v6 to %dmv\n",
rdev->desc->volt_table[selector] / 1000);
v6_prog = I2C_V6_SELECT | (u8) selector;
- return i2c_smbus_write_byte(client, v6_prog);
+ ret = i2c_smbus_write_byte(client, v6_prog);
+ if (ret)
+ return ret;
+
+ max1586->v6_curr_sel = selector;
+
+ return 0;
}
/*
@@ -95,12 +127,14 @@ static int max1586_v6_set_voltage_sel(struct regulator_dev *rdev,
* the set up value.
*/
static struct regulator_ops max1586_v3_ops = {
+ .get_voltage_sel = max1586_v3_get_voltage_sel,
.set_voltage_sel = max1586_v3_set_voltage_sel,
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
};
static struct regulator_ops max1586_v6_ops = {
+ .get_voltage_sel = max1586_v6_get_voltage_sel,
.set_voltage_sel = max1586_v6_set_voltage_sel,
.list_voltage = regulator_list_voltage_table,
};
@@ -148,6 +182,10 @@ static int max1586_pmic_probe(struct i2c_client *client,
max1586->min_uV = MAX1586_V3_MIN_UV / 1000 * pdata->v3_gain / 1000;
max1586->max_uV = MAX1586_V3_MAX_UV / 1000 * pdata->v3_gain / 1000;
+ /* Set curr_sel to default voltage on power-up */
+ max1586->v3_curr_sel = 24; /* 1.3V */
+ max1586->v6_curr_sel = 0;
+
rdev = max1586->rdev;
for (i = 0; i < pdata->num_subdevs && i <= MAX1586_V6; i++) {
id = pdata->subdevs[i].id;
diff --git a/drivers/regulator/max77686.c b/drivers/regulator/max77686.c
index cb99e9031a6..b85040caaea 100644
--- a/drivers/regulator/max77686.c
+++ b/drivers/regulator/max77686.c
@@ -67,8 +67,94 @@ enum max77686_ramp_rate {
struct max77686_data {
struct regulator_dev *rdev[MAX77686_REGULATORS];
+ unsigned int opmode[MAX77686_REGULATORS];
};
+/* Some BUCKS supports Normal[ON/OFF] mode during suspend */
+static int max77686_buck_set_suspend_disable(struct regulator_dev *rdev)
+{
+ unsigned int val;
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+
+ if (rdev->desc->id == MAX77686_BUCK1)
+ val = 0x1;
+ else
+ val = 0x1 << MAX77686_OPMODE_BUCK234_SHIFT;
+
+ max77686->opmode[rdev->desc->id] = val;
+ return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ rdev->desc->enable_mask,
+ val);
+}
+
+/* Some LDOs supports [LPM/Normal]ON mode during suspend state */
+static int max77686_set_suspend_mode(struct regulator_dev *rdev,
+ unsigned int mode)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+ unsigned int val;
+
+ /* BUCK[5-9] doesn't support this feature */
+ if (rdev->desc->id >= MAX77686_BUCK5)
+ return 0;
+
+ switch (mode) {
+ case REGULATOR_MODE_IDLE: /* ON in LP Mode */
+ val = 0x2 << MAX77686_OPMODE_SHIFT;
+ break;
+ case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
+ val = 0x3 << MAX77686_OPMODE_SHIFT;
+ break;
+ default:
+ pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
+ rdev->desc->name, mode);
+ return -EINVAL;
+ }
+
+ max77686->opmode[rdev->desc->id] = val;
+ return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ rdev->desc->enable_mask,
+ val);
+}
+
+/* Some LDOs supports LPM-ON/OFF/Normal-ON mode during suspend state */
+static int max77686_ldo_set_suspend_mode(struct regulator_dev *rdev,
+ unsigned int mode)
+{
+ unsigned int val;
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+
+ switch (mode) {
+ case REGULATOR_MODE_STANDBY: /* switch off */
+ val = 0x1 << MAX77686_OPMODE_SHIFT;
+ break;
+ case REGULATOR_MODE_IDLE: /* ON in LP Mode */
+ val = 0x2 << MAX77686_OPMODE_SHIFT;
+ break;
+ case REGULATOR_MODE_NORMAL: /* ON in Normal Mode */
+ val = 0x3 << MAX77686_OPMODE_SHIFT;
+ break;
+ default:
+ pr_warn("%s: regulator_suspend_mode : 0x%x not supported\n",
+ rdev->desc->name, mode);
+ return -EINVAL;
+ }
+
+ max77686->opmode[rdev->desc->id] = val;
+ return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ rdev->desc->enable_mask,
+ val);
+}
+
+static int max77686_enable(struct regulator_dev *rdev)
+{
+ struct max77686_data *max77686 = rdev_get_drvdata(rdev);
+
+ return regmap_update_bits(rdev->regmap, rdev->desc->enable_reg,
+ rdev->desc->enable_mask,
+ max77686->opmode[rdev->desc->id]);
+}
+
static int max77686_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
{
unsigned int ramp_value = RAMP_RATE_NO_CTRL;
@@ -98,23 +184,49 @@ static struct regulator_ops max77686_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
.is_enabled = regulator_is_enabled_regmap,
- .enable = regulator_enable_regmap,
+ .enable = max77686_enable,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_suspend_mode = max77686_set_suspend_mode,
+};
+
+static struct regulator_ops max77686_ldo_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = max77686_enable,
.disable = regulator_disable_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_suspend_mode = max77686_ldo_set_suspend_mode,
+};
+
+static struct regulator_ops max77686_buck1_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .map_voltage = regulator_map_voltage_linear,
+ .is_enabled = regulator_is_enabled_regmap,
+ .enable = max77686_enable,
+ .disable = regulator_disable_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_suspend_disable = max77686_buck_set_suspend_disable,
};
static struct regulator_ops max77686_buck_dvs_ops = {
.list_voltage = regulator_list_voltage_linear,
.map_voltage = regulator_map_voltage_linear,
.is_enabled = regulator_is_enabled_regmap,
- .enable = regulator_enable_regmap,
+ .enable = max77686_enable,
.disable = regulator_disable_regmap,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
.set_voltage_sel = regulator_set_voltage_sel_regmap,
.set_voltage_time_sel = regulator_set_voltage_time_sel,
.set_ramp_delay = max77686_set_ramp_delay,
+ .set_suspend_disable = max77686_buck_set_suspend_disable,
};
#define regulator_desc_ldo(num) { \
@@ -133,9 +245,41 @@ static struct regulator_ops max77686_buck_dvs_ops = {
.enable_mask = MAX77686_OPMODE_MASK \
<< MAX77686_OPMODE_SHIFT, \
}
+#define regulator_desc_lpm_ldo(num) { \
+ .name = "LDO"#num, \
+ .id = MAX77686_LDO##num, \
+ .ops = &max77686_ldo_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = MAX77686_LDO_MINUV, \
+ .uV_step = MAX77686_LDO_UVSTEP, \
+ .ramp_delay = MAX77686_RAMP_DELAY, \
+ .n_voltages = MAX77686_VSEL_MASK + 1, \
+ .vsel_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \
+ .vsel_mask = MAX77686_VSEL_MASK, \
+ .enable_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \
+ .enable_mask = MAX77686_OPMODE_MASK \
+ << MAX77686_OPMODE_SHIFT, \
+}
#define regulator_desc_ldo_low(num) { \
.name = "LDO"#num, \
.id = MAX77686_LDO##num, \
+ .ops = &max77686_ldo_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .owner = THIS_MODULE, \
+ .min_uV = MAX77686_LDO_LOW_MINUV, \
+ .uV_step = MAX77686_LDO_LOW_UVSTEP, \
+ .ramp_delay = MAX77686_RAMP_DELAY, \
+ .n_voltages = MAX77686_VSEL_MASK + 1, \
+ .vsel_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \
+ .vsel_mask = MAX77686_VSEL_MASK, \
+ .enable_reg = MAX77686_REG_LDO1CTRL1 + num - 1, \
+ .enable_mask = MAX77686_OPMODE_MASK \
+ << MAX77686_OPMODE_SHIFT, \
+}
+#define regulator_desc_ldo1_low(num) { \
+ .name = "LDO"#num, \
+ .id = MAX77686_LDO##num, \
.ops = &max77686_ops, \
.type = REGULATOR_VOLTAGE, \
.owner = THIS_MODULE, \
@@ -167,7 +311,7 @@ static struct regulator_ops max77686_buck_dvs_ops = {
#define regulator_desc_buck1(num) { \
.name = "BUCK"#num, \
.id = MAX77686_BUCK##num, \
- .ops = &max77686_ops, \
+ .ops = &max77686_buck1_ops, \
.type = REGULATOR_VOLTAGE, \
.owner = THIS_MODULE, \
.min_uV = MAX77686_BUCK_MINUV, \
@@ -197,7 +341,7 @@ static struct regulator_ops max77686_buck_dvs_ops = {
}
static struct regulator_desc regulators[] = {
- regulator_desc_ldo_low(1),
+ regulator_desc_ldo1_low(1),
regulator_desc_ldo_low(2),
regulator_desc_ldo(3),
regulator_desc_ldo(4),
@@ -206,13 +350,13 @@ static struct regulator_desc regulators[] = {
regulator_desc_ldo_low(7),
regulator_desc_ldo_low(8),
regulator_desc_ldo(9),
- regulator_desc_ldo(10),
- regulator_desc_ldo(11),
- regulator_desc_ldo(12),
+ regulator_desc_lpm_ldo(10),
+ regulator_desc_lpm_ldo(11),
+ regulator_desc_lpm_ldo(12),
regulator_desc_ldo(13),
- regulator_desc_ldo(14),
+ regulator_desc_lpm_ldo(14),
regulator_desc_ldo_low(15),
- regulator_desc_ldo(16),
+ regulator_desc_lpm_ldo(16),
regulator_desc_ldo(17),
regulator_desc_ldo(18),
regulator_desc_ldo(19),
@@ -314,12 +458,14 @@ static int max77686_pmic_probe(struct platform_device *pdev)
config.dev = &pdev->dev;
config.regmap = iodev->regmap;
+ config.driver_data = max77686;
platform_set_drvdata(pdev, max77686);
for (i = 0; i < MAX77686_REGULATORS; i++) {
config.init_data = pdata->regulators[i].initdata;
config.of_node = pdata->regulators[i].of_node;
+ max77686->opmode[i] = regulators[i].enable_mask;
max77686->rdev[i] = regulator_register(&regulators[i], &config);
if (IS_ERR(max77686->rdev[i])) {
ret = PTR_ERR(max77686->rdev[i]);
diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c
new file mode 100644
index 00000000000..3ee26387b12
--- /dev/null
+++ b/drivers/regulator/max8973-regulator.c
@@ -0,0 +1,505 @@
+/*
+ * max8973-regulator.c -- Maxim max8973
+ *
+ * Regulator driver for MAXIM 8973 DC-DC step-down switching regulator.
+ *
+ * Copyright (c) 2012, NVIDIA Corporation.
+ *
+ * Author: Laxman Dewangan <ldewangan@nvidia.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any kind,
+ * whether express or implied; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
+ * General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA
+ * 02111-1307, USA
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/max8973-regulator.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/slab.h>
+#include <linux/regmap.h>
+
+/* Register definitions */
+#define MAX8973_VOUT 0x0
+#define MAX8973_VOUT_DVS 0x1
+#define MAX8973_CONTROL1 0x2
+#define MAX8973_CONTROL2 0x3
+#define MAX8973_CHIPID1 0x4
+#define MAX8973_CHIPID2 0x5
+
+#define MAX8973_MAX_VOUT_REG 2
+
+/* MAX8973_VOUT */
+#define MAX8973_VOUT_ENABLE BIT(7)
+#define MAX8973_VOUT_MASK 0x7F
+
+/* MAX8973_VOUT_DVS */
+#define MAX8973_DVS_VOUT_MASK 0x7F
+
+/* MAX8973_CONTROL1 */
+#define MAX8973_SNS_ENABLE BIT(7)
+#define MAX8973_FPWM_EN_M BIT(6)
+#define MAX8973_NFSR_ENABLE BIT(5)
+#define MAX8973_AD_ENABLE BIT(4)
+#define MAX8973_BIAS_ENABLE BIT(3)
+#define MAX8973_FREQSHIFT_9PER BIT(2)
+
+#define MAX8973_RAMP_12mV_PER_US 0x0
+#define MAX8973_RAMP_25mV_PER_US 0x1
+#define MAX8973_RAMP_50mV_PER_US 0x2
+#define MAX8973_RAMP_200mV_PER_US 0x3
+
+/* MAX8973_CONTROL2 */
+#define MAX8973_WDTMR_ENABLE BIT(6)
+#define MAX8973_DISCH_ENBABLE BIT(5)
+#define MAX8973_FT_ENABLE BIT(4)
+
+#define MAX8973_CKKADV_TRIP_DISABLE 0xC
+#define MAX8973_CKKADV_TRIP_75mV_PER_US 0x0
+#define MAX8973_CKKADV_TRIP_150mV_PER_US 0x4
+#define MAX8973_CKKADV_TRIP_75mV_PER_US_HIST_DIS 0x8
+#define MAX8973_CONTROL_CLKADV_TRIP_MASK 0x00030000
+
+#define MAX8973_INDUCTOR_MIN_30_PER 0x0
+#define MAX8973_INDUCTOR_NOMINAL 0x1
+#define MAX8973_INDUCTOR_PLUS_30_PER 0x2
+#define MAX8973_INDUCTOR_PLUS_60_PER 0x3
+#define MAX8973_CONTROL_INDUCTOR_VALUE_MASK 0x00300000
+
+#define MAX8973_MIN_VOLATGE 606250
+#define MAX8973_MAX_VOLATGE 1400000
+#define MAX8973_VOLATGE_STEP 6250
+#define MAX8973_BUCK_N_VOLTAGE 0x80
+
+/* Maxim 8973 chip information */
+struct max8973_chip {
+ struct device *dev;
+ struct regulator_desc desc;
+ struct regulator_dev *rdev;
+ struct regmap *regmap;
+ bool enable_external_control;
+ int dvs_gpio;
+ int lru_index[MAX8973_MAX_VOUT_REG];
+ int curr_vout_val[MAX8973_MAX_VOUT_REG];
+ int curr_vout_reg;
+ int curr_gpio_val;
+ bool valid_dvs_gpio;
+};
+
+/*
+ * find_voltage_set_register: Find new voltage configuration register (VOUT).
+ * The finding of the new VOUT register will be based on the LRU mechanism.
+ * Each VOUT register will have different voltage configured . This
+ * Function will look if any of the VOUT register have requested voltage set
+ * or not.
+ * - If it is already there then it will make that register as most
+ * recently used and return as found so that caller need not to set
+ * the VOUT register but need to set the proper gpios to select this
+ * VOUT register.
+ * - If requested voltage is not found then it will use the least
+ * recently mechanism to get new VOUT register for new configuration
+ * and will return not_found so that caller need to set new VOUT
+ * register and then gpios (both).
+ */
+static bool find_voltage_set_register(struct max8973_chip *tps,
+ int req_vsel, int *vout_reg, int *gpio_val)
+{
+ int i;
+ bool found = false;
+ int new_vout_reg = tps->lru_index[MAX8973_MAX_VOUT_REG - 1];
+ int found_index = MAX8973_MAX_VOUT_REG - 1;
+
+ for (i = 0; i < MAX8973_MAX_VOUT_REG; ++i) {
+ if (tps->curr_vout_val[tps->lru_index[i]] == req_vsel) {
+ new_vout_reg = tps->lru_index[i];
+ found_index = i;
+ found = true;
+ goto update_lru_index;
+ }
+ }
+
+update_lru_index:
+ for (i = found_index; i > 0; i--)
+ tps->lru_index[i] = tps->lru_index[i - 1];
+
+ tps->lru_index[0] = new_vout_reg;
+ *gpio_val = new_vout_reg;
+ *vout_reg = MAX8973_VOUT + new_vout_reg;
+ return found;
+}
+
+static int max8973_dcdc_get_voltage_sel(struct regulator_dev *rdev)
+{
+ struct max8973_chip *max = rdev_get_drvdata(rdev);
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(max->regmap, max->curr_vout_reg, &data);
+ if (ret < 0) {
+ dev_err(max->dev, "register %d read failed, err = %d\n",
+ max->curr_vout_reg, ret);
+ return ret;
+ }
+ return data & MAX8973_VOUT_MASK;
+}
+
+static int max8973_dcdc_set_voltage_sel(struct regulator_dev *rdev,
+ unsigned vsel)
+{
+ struct max8973_chip *max = rdev_get_drvdata(rdev);
+ int ret;
+ bool found = false;
+ int vout_reg = max->curr_vout_reg;
+ int gpio_val = max->curr_gpio_val;
+
+ /*
+ * If gpios are available to select the VOUT register then least
+ * recently used register for new configuration.
+ */
+ if (max->valid_dvs_gpio)
+ found = find_voltage_set_register(max, vsel,
+ &vout_reg, &gpio_val);
+
+ if (!found) {
+ ret = regmap_update_bits(max->regmap, vout_reg,
+ MAX8973_VOUT_MASK, vsel);
+ if (ret < 0) {
+ dev_err(max->dev, "register %d update failed, err %d\n",
+ vout_reg, ret);
+ return ret;
+ }
+ max->curr_vout_reg = vout_reg;
+ max->curr_vout_val[gpio_val] = vsel;
+ }
+
+ /* Select proper VOUT register vio gpios */
+ if (max->valid_dvs_gpio) {
+ gpio_set_value_cansleep(max->dvs_gpio, gpio_val & 0x1);
+ max->curr_gpio_val = gpio_val;
+ }
+ return 0;
+}
+
+static int max8973_dcdc_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ struct max8973_chip *max = rdev_get_drvdata(rdev);
+ int ret;
+ int pwm;
+
+ /* Enable force PWM mode in FAST mode only. */
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ pwm = MAX8973_FPWM_EN_M;
+ break;
+
+ case REGULATOR_MODE_NORMAL:
+ pwm = 0;
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ ret = regmap_update_bits(max->regmap, MAX8973_CONTROL1,
+ MAX8973_FPWM_EN_M, pwm);
+ if (ret < 0)
+ dev_err(max->dev, "register %d update failed, err %d\n",
+ MAX8973_CONTROL1, ret);
+ return ret;
+}
+
+static unsigned int max8973_dcdc_get_mode(struct regulator_dev *rdev)
+{
+ struct max8973_chip *max = rdev_get_drvdata(rdev);
+ unsigned int data;
+ int ret;
+
+ ret = regmap_read(max->regmap, MAX8973_CONTROL1, &data);
+ if (ret < 0) {
+ dev_err(max->dev, "register %d read failed, err %d\n",
+ MAX8973_CONTROL1, ret);
+ return ret;
+ }
+ return (data & MAX8973_FPWM_EN_M) ?
+ REGULATOR_MODE_FAST : REGULATOR_MODE_NORMAL;
+}
+
+static struct regulator_ops max8973_dcdc_ops = {
+ .get_voltage_sel = max8973_dcdc_get_voltage_sel,
+ .set_voltage_sel = max8973_dcdc_set_voltage_sel,
+ .list_voltage = regulator_list_voltage_linear,
+ .set_mode = max8973_dcdc_set_mode,
+ .get_mode = max8973_dcdc_get_mode,
+};
+
+static int __devinit max8973_init_dcdc(struct max8973_chip *max,
+ struct max8973_regulator_platform_data *pdata)
+{
+ int ret;
+ uint8_t control1 = 0;
+ uint8_t control2 = 0;
+
+ if (pdata->control_flags & MAX8973_CONTROL_REMOTE_SENSE_ENABLE)
+ control1 |= MAX8973_SNS_ENABLE;
+
+ if (!(pdata->control_flags & MAX8973_CONTROL_FALLING_SLEW_RATE_ENABLE))
+ control1 |= MAX8973_NFSR_ENABLE;
+
+ if (pdata->control_flags & MAX8973_CONTROL_OUTPUT_ACTIVE_DISCH_ENABLE)
+ control1 |= MAX8973_AD_ENABLE;
+
+ if (pdata->control_flags & MAX8973_CONTROL_BIAS_ENABLE)
+ control1 |= MAX8973_BIAS_ENABLE;
+
+ if (pdata->control_flags & MAX8973_CONTROL_FREQ_SHIFT_9PER_ENABLE)
+ control1 |= MAX8973_FREQSHIFT_9PER;
+
+ /* Set ramp delay */
+ if (pdata->reg_init_data &&
+ pdata->reg_init_data->constraints.ramp_delay) {
+ if (pdata->reg_init_data->constraints.ramp_delay < 25000)
+ control1 = MAX8973_RAMP_12mV_PER_US;
+ else if (pdata->reg_init_data->constraints.ramp_delay < 50000)
+ control1 = MAX8973_RAMP_25mV_PER_US;
+ else if (pdata->reg_init_data->constraints.ramp_delay < 200000)
+ control1 = MAX8973_RAMP_50mV_PER_US;
+ else
+ control1 = MAX8973_RAMP_200mV_PER_US;
+ } else {
+ control1 = MAX8973_RAMP_12mV_PER_US;
+ max->desc.ramp_delay = 12500;
+ }
+
+ if (!(pdata->control_flags & MAX8973_CONTROL_PULL_DOWN_ENABLE))
+ control2 |= MAX8973_DISCH_ENBABLE;
+
+ /* Clock advance trip configuration */
+ switch (pdata->control_flags & MAX8973_CONTROL_CLKADV_TRIP_MASK) {
+ case MAX8973_CONTROL_CLKADV_TRIP_DISABLED:
+ control2 |= MAX8973_CKKADV_TRIP_DISABLE;
+ break;
+
+ case MAX8973_CONTROL_CLKADV_TRIP_75mV_PER_US:
+ control2 |= MAX8973_CKKADV_TRIP_75mV_PER_US;
+ break;
+
+ case MAX8973_CONTROL_CLKADV_TRIP_150mV_PER_US:
+ control2 |= MAX8973_CKKADV_TRIP_150mV_PER_US;
+ break;
+
+ case MAX8973_CONTROL_CLKADV_TRIP_75mV_PER_US_HIST_DIS:
+ control2 |= MAX8973_CKKADV_TRIP_75mV_PER_US_HIST_DIS;
+ break;
+ }
+
+ /* Configure inductor value */
+ switch (pdata->control_flags & MAX8973_CONTROL_INDUCTOR_VALUE_MASK) {
+ case MAX8973_CONTROL_INDUCTOR_VALUE_NOMINAL:
+ control2 |= MAX8973_INDUCTOR_NOMINAL;
+ break;
+
+ case MAX8973_CONTROL_INDUCTOR_VALUE_MINUS_30_PER:
+ control2 |= MAX8973_INDUCTOR_MIN_30_PER;
+ break;
+
+ case MAX8973_CONTROL_INDUCTOR_VALUE_PLUS_30_PER:
+ control2 |= MAX8973_INDUCTOR_PLUS_30_PER;
+ break;
+
+ case MAX8973_CONTROL_INDUCTOR_VALUE_PLUS_60_PER:
+ control2 |= MAX8973_INDUCTOR_PLUS_60_PER;
+ break;
+ }
+
+ ret = regmap_write(max->regmap, MAX8973_CONTROL1, control1);
+ if (ret < 0) {
+ dev_err(max->dev, "register %d write failed, err = %d",
+ MAX8973_CONTROL1, ret);
+ return ret;
+ }
+
+ ret = regmap_write(max->regmap, MAX8973_CONTROL2, control2);
+ if (ret < 0) {
+ dev_err(max->dev, "register %d write failed, err = %d",
+ MAX8973_CONTROL2, ret);
+ return ret;
+ }
+
+ /* If external control is enabled then disable EN bit */
+ if (max->enable_external_control) {
+ ret = regmap_update_bits(max->regmap, MAX8973_VOUT,
+ MAX8973_VOUT_ENABLE, 0);
+ if (ret < 0)
+ dev_err(max->dev, "register %d update failed, err = %d",
+ MAX8973_VOUT, ret);
+ }
+ return ret;
+}
+
+static const struct regmap_config max8973_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MAX8973_CHIPID2,
+ .cache_type = REGCACHE_RBTREE,
+};
+
+static int __devinit max8973_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct max8973_regulator_platform_data *pdata;
+ struct regulator_config config = { };
+ struct regulator_dev *rdev;
+ struct max8973_chip *max;
+ int ret;
+
+ pdata = client->dev.platform_data;
+ if (!pdata) {
+ dev_err(&client->dev, "No Platform data");
+ return -EIO;
+ }
+
+ max = devm_kzalloc(&client->dev, sizeof(*max), GFP_KERNEL);
+ if (!max) {
+ dev_err(&client->dev, "Memory allocation for max failed\n");
+ return -ENOMEM;
+ }
+
+ max->regmap = devm_regmap_init_i2c(client, &max8973_regmap_config);
+ if (IS_ERR(max->regmap)) {
+ ret = PTR_ERR(max->regmap);
+ dev_err(&client->dev, "regmap init failed, err %d\n", ret);
+ return ret;
+ }
+
+ i2c_set_clientdata(client, max);
+ max->dev = &client->dev;
+ max->desc.name = id->name;
+ max->desc.id = 0;
+ max->desc.ops = &max8973_dcdc_ops;
+ max->desc.type = REGULATOR_VOLTAGE;
+ max->desc.owner = THIS_MODULE;
+ max->desc.min_uV = MAX8973_MIN_VOLATGE;
+ max->desc.uV_step = MAX8973_VOLATGE_STEP;
+ max->desc.n_voltages = MAX8973_BUCK_N_VOLTAGE;
+
+ if (!pdata->enable_ext_control) {
+ max->desc.enable_reg = MAX8973_VOUT;
+ max->desc.enable_mask = MAX8973_VOUT_ENABLE;
+ max8973_dcdc_ops.enable = regulator_enable_regmap;
+ max8973_dcdc_ops.disable = regulator_disable_regmap;
+ max8973_dcdc_ops.is_enabled = regulator_is_enabled_regmap;
+ }
+
+ max->enable_external_control = pdata->enable_ext_control;
+ max->dvs_gpio = pdata->dvs_gpio;
+ max->curr_gpio_val = pdata->dvs_def_state;
+ max->curr_vout_reg = MAX8973_VOUT + pdata->dvs_def_state;
+ max->lru_index[0] = max->curr_vout_reg;
+ max->valid_dvs_gpio = false;
+
+ if (gpio_is_valid(max->dvs_gpio)) {
+ int gpio_flags;
+ int i;
+
+ gpio_flags = (pdata->dvs_def_state) ?
+ GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW;
+ ret = devm_gpio_request_one(&client->dev, max->dvs_gpio,
+ gpio_flags, "max8973-dvs");
+ if (ret) {
+ dev_err(&client->dev,
+ "gpio_request for gpio %d failed, err = %d\n",
+ max->dvs_gpio, ret);
+ return ret;
+ }
+ max->valid_dvs_gpio = true;
+
+ /*
+ * Initialize the lru index with vout_reg id
+ * The index 0 will be most recently used and
+ * set with the max->curr_vout_reg */
+ for (i = 0; i < MAX8973_MAX_VOUT_REG; ++i)
+ max->lru_index[i] = i;
+ max->lru_index[0] = max->curr_vout_reg;
+ max->lru_index[max->curr_vout_reg] = 0;
+ }
+
+ ret = max8973_init_dcdc(max, pdata);
+ if (ret < 0) {
+ dev_err(max->dev, "Max8973 Init failed, err = %d\n", ret);
+ return ret;
+ }
+
+ config.dev = &client->dev;
+ config.init_data = pdata->reg_init_data;
+ config.driver_data = max;
+ config.of_node = client->dev.of_node;
+ config.regmap = max->regmap;
+
+ /* Register the regulators */
+ rdev = regulator_register(&max->desc, &config);
+ if (IS_ERR(rdev)) {
+ ret = PTR_ERR(rdev);
+ dev_err(max->dev, "regulator register failed, err %d\n", ret);
+ return ret;
+ }
+
+ max->rdev = rdev;
+ return 0;
+}
+
+static int __devexit max8973_remove(struct i2c_client *client)
+{
+ struct max8973_chip *max = i2c_get_clientdata(client);
+
+ regulator_unregister(max->rdev);
+ return 0;
+}
+
+static const struct i2c_device_id max8973_id[] = {
+ {.name = "max8973",},
+ {},
+};
+
+MODULE_DEVICE_TABLE(i2c, max8973_id);
+
+static struct i2c_driver max8973_i2c_driver = {
+ .driver = {
+ .name = "max8973",
+ .owner = THIS_MODULE,
+ },
+ .probe = max8973_probe,
+ .remove = __devexit_p(max8973_remove),
+ .id_table = max8973_id,
+};
+
+static int __init max8973_init(void)
+{
+ return i2c_add_driver(&max8973_i2c_driver);
+}
+subsys_initcall(max8973_init);
+
+static void __exit max8973_cleanup(void)
+{
+ i2c_del_driver(&max8973_i2c_driver);
+}
+module_exit(max8973_cleanup);
+
+MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>");
+MODULE_DESCRIPTION("MAX8973 voltage regulator driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/regulator/wm831x-dcdc.c b/drivers/regulator/wm831x-dcdc.c
index 33297bcce3f..bce25658e12 100644
--- a/drivers/regulator/wm831x-dcdc.c
+++ b/drivers/regulator/wm831x-dcdc.c
@@ -290,7 +290,7 @@ static int wm831x_buckv_set_voltage_sel(struct regulator_dev *rdev,
if (vsel > dcdc->dvs_vsel) {
ret = wm831x_set_bits(wm831x, dvs_reg,
WM831X_DC1_DVS_VSEL_MASK,
- dcdc->dvs_vsel);
+ vsel);
if (ret == 0)
dcdc->dvs_vsel = vsel;
else
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2025-01-19 09:26:10 +0000