diff options
Diffstat (limited to 'drivers/rtc/rtc-omap.c')
| -rw-r--r-- | drivers/rtc/rtc-omap.c | 46 |
1 files changed, 30 insertions, 16 deletions
diff --git a/drivers/rtc/rtc-omap.c b/drivers/rtc/rtc-omap.c index 64d9727b722..b4dbf3a319b 100644 --- a/drivers/rtc/rtc-omap.c +++ b/drivers/rtc/rtc-omap.c @@ -34,7 +34,8 @@ * Board-specific wiring options include using split power mode with * RTC_OFF_NOFF used as the reset signal (so the RTC won't be reset), * and wiring RTC_WAKE_INT (so the RTC alarm can wake the system from - * low power modes). See the BOARD-SPECIFIC CUSTOMIZATION comment. + * low power modes) for OMAP1 boards (OMAP-L138 has this built into + * the SoC). See the BOARD-SPECIFIC CUSTOMIZATION comment. */ #define OMAP_RTC_BASE 0xfffb4800 @@ -142,8 +143,6 @@ omap_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long arg) u8 reg; switch (cmd) { - case RTC_AIE_OFF: - case RTC_AIE_ON: case RTC_UIE_OFF: case RTC_UIE_ON: break; @@ -155,13 +154,6 @@ omap_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long arg) rtc_wait_not_busy(); reg = rtc_read(OMAP_RTC_INTERRUPTS_REG); switch (cmd) { - /* AIE = Alarm Interrupt Enable */ - case RTC_AIE_OFF: - reg &= ~OMAP_RTC_INTERRUPTS_IT_ALARM; - break; - case RTC_AIE_ON: - reg |= OMAP_RTC_INTERRUPTS_IT_ALARM; - break; /* UIE = Update Interrupt Enable (1/second) */ case RTC_UIE_OFF: reg &= ~OMAP_RTC_INTERRUPTS_IT_TIMER; @@ -181,6 +173,24 @@ omap_rtc_ioctl(struct device *dev, unsigned int cmd, unsigned long arg) #define omap_rtc_ioctl NULL #endif +static int omap_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled) +{ + u8 reg; + + local_irq_disable(); + rtc_wait_not_busy(); + reg = rtc_read(OMAP_RTC_INTERRUPTS_REG); + if (enabled) + reg |= OMAP_RTC_INTERRUPTS_IT_ALARM; + else + reg &= ~OMAP_RTC_INTERRUPTS_IT_ALARM; + rtc_wait_not_busy(); + rtc_write(reg, OMAP_RTC_INTERRUPTS_REG); + local_irq_enable(); + + return 0; +} + /* this hardware doesn't support "don't care" alarm fields */ static int tm2bcd(struct rtc_time *tm) { @@ -308,6 +318,7 @@ static struct rtc_class_ops omap_rtc_ops = { .set_time = omap_rtc_set_time, .read_alarm = omap_rtc_read_alarm, .set_alarm = omap_rtc_set_alarm, + .alarm_irq_enable = omap_rtc_alarm_irq_enable, }; static int omap_rtc_alarm; @@ -401,16 +412,17 @@ static int __init omap_rtc_probe(struct platform_device *pdev) /* BOARD-SPECIFIC CUSTOMIZATION CAN GO HERE: * - * - Boards wired so that RTC_WAKE_INT does something, and muxed - * right (W13_1610_RTC_WAKE_INT is the default after chip reset), - * should initialize the device wakeup flag appropriately. + * - Device wake-up capability setting should come through chip + * init logic. OMAP1 boards should initialize the "wakeup capable" + * flag in the platform device if the board is wired right for + * being woken up by RTC alarm. For OMAP-L138, this capability + * is built into the SoC by the "Deep Sleep" capability. * * - Boards wired so RTC_ON_nOFF is used as the reset signal, * rather than nPWRON_RESET, should forcibly enable split * power mode. (Some chip errata report that RTC_CTRL_SPLIT * is write-only, and always reads as zero...) */ - device_init_wakeup(&pdev->dev, 0); if (new_ctrl & (u8) OMAP_RTC_CTRL_SPLIT) pr_info("%s: split power mode\n", pdev->name); @@ -427,13 +439,14 @@ fail1: fail0: iounmap(rtc_base); fail: - release_resource(mem); + release_mem_region(mem->start, resource_size(mem)); return -EIO; } static int __exit omap_rtc_remove(struct platform_device *pdev) { struct rtc_device *rtc = platform_get_drvdata(pdev); + struct resource *mem = dev_get_drvdata(&rtc->dev); device_init_wakeup(&pdev->dev, 0); @@ -445,8 +458,9 @@ static int __exit omap_rtc_remove(struct platform_device *pdev) if (omap_rtc_timer != omap_rtc_alarm) free_irq(omap_rtc_alarm, rtc); - release_resource(dev_get_drvdata(&rtc->dev)); rtc_device_unregister(rtc); + iounmap(rtc_base); + release_mem_region(mem->start, resource_size(mem)); return 0; } |