diff options
Diffstat (limited to 'drivers/scsi/lpfc/lpfc_attr.c')
| -rw-r--r-- | drivers/scsi/lpfc/lpfc_attr.c | 217 |
1 files changed, 191 insertions, 26 deletions
diff --git a/drivers/scsi/lpfc/lpfc_attr.c b/drivers/scsi/lpfc/lpfc_attr.c index 80a11218b9b..4bae4a2ed2f 100644 --- a/drivers/scsi/lpfc/lpfc_attr.c +++ b/drivers/scsi/lpfc/lpfc_attr.c @@ -1,7 +1,7 @@ /******************************************************************* * This file is part of the Emulex Linux Device Driver for * * Fibre Channel Host Bus Adapters. * - * Copyright (C) 2004-2007 Emulex. All rights reserved. * + * Copyright (C) 2004-2008 Emulex. All rights reserved. * * EMULEX and SLI are trademarks of Emulex. * * www.emulex.com * * Portions Copyright (C) 2004-2005 Christoph Hellwig * @@ -45,6 +45,10 @@ #define LPFC_MIN_DEVLOSS_TMO 1 #define LPFC_MAX_DEVLOSS_TMO 255 +#define LPFC_MAX_LINK_SPEED 8 +#define LPFC_LINK_SPEED_BITMAP 0x00000117 +#define LPFC_LINK_SPEED_STRING "0, 1, 2, 4, 8" + static void lpfc_jedec_to_ascii(int incr, char hdw[]) { @@ -86,6 +90,15 @@ lpfc_serialnum_show(struct class_device *cdev, char *buf) } static ssize_t +lpfc_temp_sensor_show(struct class_device *cdev, char *buf) +{ + struct Scsi_Host *shost = class_to_shost(cdev); + struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata; + struct lpfc_hba *phba = vport->phba; + return snprintf(buf, PAGE_SIZE, "%d\n",phba->temp_sensor_support); +} + +static ssize_t lpfc_modeldesc_show(struct class_device *cdev, char *buf) { struct Scsi_Host *shost = class_to_shost(cdev); @@ -178,12 +191,9 @@ lpfc_state_show(struct class_device *cdev, char *buf) case LPFC_LINK_UP: case LPFC_CLEAR_LA: case LPFC_HBA_READY: - len += snprintf(buf + len, PAGE_SIZE-len, "Link Up - \n"); + len += snprintf(buf + len, PAGE_SIZE-len, "Link Up - "); switch (vport->port_state) { - len += snprintf(buf + len, PAGE_SIZE-len, - "initializing\n"); - break; case LPFC_LOCAL_CFG_LINK: len += snprintf(buf + len, PAGE_SIZE-len, "Configuring Link\n"); @@ -252,8 +262,7 @@ lpfc_issue_lip(struct Scsi_Host *shost) int mbxstatus = MBXERR_ERROR; if ((vport->fc_flag & FC_OFFLINE_MODE) || - (phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO) || - (vport->port_state != LPFC_VPORT_READY)) + (phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO)) return -EPERM; pmboxq = mempool_alloc(phba->mbox_mem_pool,GFP_KERNEL); @@ -305,12 +314,14 @@ lpfc_do_offline(struct lpfc_hba *phba, uint32_t type) psli = &phba->sli; + /* Wait a little for things to settle down, but not + * long enough for dev loss timeout to expire. + */ for (i = 0; i < psli->num_rings; i++) { pring = &psli->ring[i]; - /* The linkdown event takes 30 seconds to timeout. */ while (pring->txcmplq_cnt) { msleep(10); - if (cnt++ > 3000) { + if (cnt++ > 500) { /* 5 secs */ lpfc_printf_log(phba, KERN_WARNING, LOG_INIT, "0466 Outstanding IO when " @@ -336,6 +347,9 @@ lpfc_selective_reset(struct lpfc_hba *phba) struct completion online_compl; int status = 0; + if (!phba->cfg_enable_hba_reset) + return -EIO; + status = lpfc_do_offline(phba, LPFC_EVT_OFFLINE); if (status != 0) @@ -409,6 +423,8 @@ lpfc_board_mode_store(struct class_device *cdev, const char *buf, size_t count) struct completion online_compl; int status=0; + if (!phba->cfg_enable_hba_reset) + return -EACCES; init_completion(&online_compl); if(strncmp(buf, "online", sizeof("online") - 1) == 0) { @@ -908,6 +924,8 @@ static CLASS_DEVICE_ATTR(used_rpi, S_IRUGO, lpfc_used_rpi_show, NULL); static CLASS_DEVICE_ATTR(max_xri, S_IRUGO, lpfc_max_xri_show, NULL); static CLASS_DEVICE_ATTR(used_xri, S_IRUGO, lpfc_used_xri_show, NULL); static CLASS_DEVICE_ATTR(npiv_info, S_IRUGO, lpfc_npiv_info_show, NULL); +static CLASS_DEVICE_ATTR(lpfc_temp_sensor, S_IRUGO, lpfc_temp_sensor_show, + NULL); static char *lpfc_soft_wwn_key = "C99G71SL8032A"; @@ -971,6 +989,14 @@ lpfc_soft_wwpn_store(struct class_device *cdev, const char *buf, size_t count) unsigned int i, j, cnt=count; u8 wwpn[8]; + if (!phba->cfg_enable_hba_reset) + return -EACCES; + spin_lock_irq(&phba->hbalock); + if (phba->over_temp_state == HBA_OVER_TEMP) { + spin_unlock_irq(&phba->hbalock); + return -EACCES; + } + spin_unlock_irq(&phba->hbalock); /* count may include a LF at end of string */ if (buf[cnt-1] == '\n') cnt--; @@ -1102,7 +1128,13 @@ MODULE_PARM_DESC(lpfc_sli_mode, "SLI mode selector:" " 2 - select SLI-2 even on SLI-3 capable HBAs," " 3 - select SLI-3"); -LPFC_ATTR_R(enable_npiv, 0, 0, 1, "Enable NPIV functionality"); +int lpfc_enable_npiv = 0; +module_param(lpfc_enable_npiv, int, 0); +MODULE_PARM_DESC(lpfc_enable_npiv, "Enable NPIV functionality"); +lpfc_param_show(enable_npiv); +lpfc_param_init(enable_npiv, 0, 0, 1); +static CLASS_DEVICE_ATTR(lpfc_enable_npiv, S_IRUGO, + lpfc_enable_npiv_show, NULL); /* # lpfc_nodev_tmo: If set, it will hold all I/O errors on devices that disappear @@ -1248,6 +1280,13 @@ LPFC_VPORT_ATTR_HEX_RW(log_verbose, 0x0, 0x0, 0xffff, "Verbose logging bit-mask"); /* +# lpfc_enable_da_id: This turns on the DA_ID CT command that deregisters +# objects that have been registered with the nameserver after login. +*/ +LPFC_VPORT_ATTR_R(enable_da_id, 0, 0, 1, + "Deregister nameserver objects before LOGO"); + +/* # lun_queue_depth: This parameter is used to limit the number of outstanding # commands per FCP LUN. Value range is [1,128]. Default value is 30. */ @@ -1369,7 +1408,33 @@ LPFC_VPORT_ATTR_R(scan_down, 1, 0, 1, # Set loop mode if you want to run as an NL_Port. Value range is [0,0x6]. # Default value is 0. */ -LPFC_ATTR_RW(topology, 0, 0, 6, "Select Fibre Channel topology"); +static int +lpfc_topology_set(struct lpfc_hba *phba, int val) +{ + int err; + uint32_t prev_val; + if (val >= 0 && val <= 6) { + prev_val = phba->cfg_topology; + phba->cfg_topology = val; + err = lpfc_issue_lip(lpfc_shost_from_vport(phba->pport)); + if (err) + phba->cfg_topology = prev_val; + return err; + } + lpfc_printf_log(phba, KERN_ERR, LOG_INIT, + "%d:0467 lpfc_topology attribute cannot be set to %d, " + "allowed range is [0, 6]\n", + phba->brd_no, val); + return -EINVAL; +} +static int lpfc_topology = 0; +module_param(lpfc_topology, int, 0); +MODULE_PARM_DESC(lpfc_topology, "Select Fibre Channel topology"); +lpfc_param_show(topology) +lpfc_param_init(topology, 0, 0, 6) +lpfc_param_store(topology) +static CLASS_DEVICE_ATTR(lpfc_topology, S_IRUGO | S_IWUSR, + lpfc_topology_show, lpfc_topology_store); /* # lpfc_link_speed: Link speed selection for initializing the Fibre Channel @@ -1381,7 +1446,59 @@ LPFC_ATTR_RW(topology, 0, 0, 6, "Select Fibre Channel topology"); # 8 = 8 Gigabaud # Value range is [0,8]. Default value is 0. */ -LPFC_ATTR_R(link_speed, 0, 0, 8, "Select link speed"); +static int +lpfc_link_speed_set(struct lpfc_hba *phba, int val) +{ + int err; + uint32_t prev_val; + + if (((val == LINK_SPEED_1G) && !(phba->lmt & LMT_1Gb)) || + ((val == LINK_SPEED_2G) && !(phba->lmt & LMT_2Gb)) || + ((val == LINK_SPEED_4G) && !(phba->lmt & LMT_4Gb)) || + ((val == LINK_SPEED_8G) && !(phba->lmt & LMT_8Gb)) || + ((val == LINK_SPEED_10G) && !(phba->lmt & LMT_10Gb))) + return -EINVAL; + + if ((val >= 0 && val <= LPFC_MAX_LINK_SPEED) + && (LPFC_LINK_SPEED_BITMAP & (1 << val))) { + prev_val = phba->cfg_link_speed; + phba->cfg_link_speed = val; + err = lpfc_issue_lip(lpfc_shost_from_vport(phba->pport)); + if (err) + phba->cfg_link_speed = prev_val; + return err; + } + + lpfc_printf_log(phba, KERN_ERR, LOG_INIT, + "%d:0469 lpfc_link_speed attribute cannot be set to %d, " + "allowed range is [0, 8]\n", + phba->brd_no, val); + return -EINVAL; +} + +static int lpfc_link_speed = 0; +module_param(lpfc_link_speed, int, 0); +MODULE_PARM_DESC(lpfc_link_speed, "Select link speed"); +lpfc_param_show(link_speed) +static int +lpfc_link_speed_init(struct lpfc_hba *phba, int val) +{ + if ((val >= 0 && val <= LPFC_MAX_LINK_SPEED) + && (LPFC_LINK_SPEED_BITMAP & (1 << val))) { + phba->cfg_link_speed = val; + return 0; + } + lpfc_printf_log(phba, KERN_ERR, LOG_INIT, + "0454 lpfc_link_speed attribute cannot " + "be set to %d, allowed values are " + "["LPFC_LINK_SPEED_STRING"]\n", val); + phba->cfg_link_speed = 0; + return -EINVAL; +} + +lpfc_param_store(link_speed) +static CLASS_DEVICE_ATTR(lpfc_link_speed, S_IRUGO | S_IWUSR, + lpfc_link_speed_show, lpfc_link_speed_store); /* # lpfc_fcp_class: Determines FC class to use for the FCP protocol. @@ -1479,7 +1596,30 @@ LPFC_ATTR_RW(poll_tmo, 10, 1, 255, */ LPFC_ATTR_R(use_msi, 0, 0, 1, "Use Message Signaled Interrupts, if possible"); +/* +# lpfc_enable_hba_reset: Allow or prevent HBA resets to the hardware. +# 0 = HBA resets disabled +# 1 = HBA resets enabled (default) +# Value range is [0,1]. Default value is 1. +*/ +LPFC_ATTR_R(enable_hba_reset, 1, 0, 1, "Enable HBA resets from the driver."); + +/* +# lpfc_enable_hba_heartbeat: Enable HBA heartbeat timer.. +# 0 = HBA Heartbeat disabled +# 1 = HBA Heartbeat enabled (default) +# Value range is [0,1]. Default value is 1. +*/ +LPFC_ATTR_R(enable_hba_heartbeat, 1, 0, 1, "Enable HBA Heartbeat."); +/* + * lpfc_sg_seg_cnt: Initial Maximum DMA Segment Count + * This value can be set to values between 64 and 256. The default value is + * 64, but may be increased to allow for larger Max I/O sizes. The scsi layer + * will be allowed to request I/Os of sizes up to (MAX_SEG_COUNT * SEG_SIZE). + */ +LPFC_ATTR_R(sg_seg_cnt, LPFC_DEFAULT_SG_SEG_CNT, LPFC_DEFAULT_SG_SEG_CNT, + LPFC_MAX_SG_SEG_CNT, "Max Scatter Gather Segment Count"); struct class_device_attribute *lpfc_hba_attrs[] = { &class_device_attr_info, @@ -1494,6 +1634,7 @@ struct class_device_attribute *lpfc_hba_attrs[] = { &class_device_attr_state, &class_device_attr_num_discovered_ports, &class_device_attr_lpfc_drvr_version, + &class_device_attr_lpfc_temp_sensor, &class_device_attr_lpfc_log_verbose, &class_device_attr_lpfc_lun_queue_depth, &class_device_attr_lpfc_hba_queue_depth, @@ -1530,6 +1671,9 @@ struct class_device_attribute *lpfc_hba_attrs[] = { &class_device_attr_lpfc_soft_wwnn, &class_device_attr_lpfc_soft_wwpn, &class_device_attr_lpfc_soft_wwn_enable, + &class_device_attr_lpfc_enable_hba_reset, + &class_device_attr_lpfc_enable_hba_heartbeat, + &class_device_attr_lpfc_sg_seg_cnt, NULL, }; @@ -1552,6 +1696,7 @@ struct class_device_attribute *lpfc_vport_attrs[] = { &class_device_attr_lpfc_max_luns, &class_device_attr_nport_evt_cnt, &class_device_attr_npiv_info, + &class_device_attr_lpfc_enable_da_id, NULL, }; @@ -1727,13 +1872,18 @@ sysfs_mbox_read(struct kobject *kobj, struct bin_attribute *bin_attr, spin_lock_irq(&phba->hbalock); + if (phba->over_temp_state == HBA_OVER_TEMP) { + sysfs_mbox_idle(phba); + spin_unlock_irq(&phba->hbalock); + return -EACCES; + } + if (off == 0 && phba->sysfs_mbox.state == SMBOX_WRITING && phba->sysfs_mbox.offset >= 2 * sizeof(uint32_t)) { switch (phba->sysfs_mbox.mbox->mb.mbxCommand) { /* Offline only */ - case MBX_WRITE_NV: case MBX_INIT_LINK: case MBX_DOWN_LINK: case MBX_CONFIG_LINK: @@ -1744,9 +1894,7 @@ sysfs_mbox_read(struct kobject *kobj, struct bin_attribute *bin_attr, case MBX_DUMP_CONTEXT: case MBX_RUN_DIAGS: case MBX_RESTART: - case MBX_FLASH_WR_ULA: case MBX_SET_MASK: - case MBX_SET_SLIM: case MBX_SET_DEBUG: if (!(vport->fc_flag & FC_OFFLINE_MODE)) { printk(KERN_WARNING "mbox_read:Command 0x%x " @@ -1756,6 +1904,8 @@ sysfs_mbox_read(struct kobject *kobj, struct bin_attribute *bin_attr, spin_unlock_irq(&phba->hbalock); return -EPERM; } + case MBX_WRITE_NV: + case MBX_WRITE_VPARMS: case MBX_LOAD_SM: case MBX_READ_NV: case MBX_READ_CONFIG: @@ -1772,6 +1922,8 @@ sysfs_mbox_read(struct kobject *kobj, struct bin_attribute *bin_attr, case MBX_LOAD_EXP_ROM: case MBX_BEACON: case MBX_DEL_LD_ENTRY: + case MBX_SET_VARIABLE: + case MBX_WRITE_WWN: break; case MBX_READ_SPARM64: case MBX_READ_LA: @@ -1793,6 +1945,17 @@ sysfs_mbox_read(struct kobject *kobj, struct bin_attribute *bin_attr, return -EPERM; } + /* If HBA encountered an error attention, allow only DUMP + * mailbox command until the HBA is restarted. + */ + if ((phba->pport->stopped) && + (phba->sysfs_mbox.mbox->mb.mbxCommand + != MBX_DUMP_MEMORY)) { + sysfs_mbox_idle(phba); + spin_unlock_irq(&phba->hbalock); + return -EPERM; + } + phba->sysfs_mbox.mbox->vport = vport; if (phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO) { @@ -1993,7 +2156,8 @@ lpfc_get_host_speed(struct Scsi_Host *shost) fc_host_speed(shost) = FC_PORTSPEED_UNKNOWN; break; } - } + } else + fc_host_speed(shost) = FC_PORTSPEED_UNKNOWN; spin_unlock_irq(shost->host_lock); } @@ -2013,7 +2177,7 @@ lpfc_get_host_fabric_name (struct Scsi_Host *shost) node_name = wwn_to_u64(phba->fc_fabparam.nodeName.u.wwn); else /* fabric is local port if there is no F/FL_Port */ - node_name = wwn_to_u64(vport->fc_nodename.u.wwn); + node_name = 0; spin_unlock_irq(shost->host_lock); @@ -2337,8 +2501,6 @@ struct fc_function_template lpfc_transport_functions = { .dev_loss_tmo_callbk = lpfc_dev_loss_tmo_callbk, .terminate_rport_io = lpfc_terminate_rport_io, - .vport_create = lpfc_vport_create, - .vport_delete = lpfc_vport_delete, .dd_fcvport_size = sizeof(struct lpfc_vport *), }; @@ -2414,21 +2576,23 @@ lpfc_get_cfgparam(struct lpfc_hba *phba) lpfc_poll_tmo_init(phba, lpfc_poll_tmo); lpfc_enable_npiv_init(phba, lpfc_enable_npiv); lpfc_use_msi_init(phba, lpfc_use_msi); + lpfc_enable_hba_reset_init(phba, lpfc_enable_hba_reset); + lpfc_enable_hba_heartbeat_init(phba, lpfc_enable_hba_heartbeat); phba->cfg_poll = lpfc_poll; phba->cfg_soft_wwnn = 0L; phba->cfg_soft_wwpn = 0L; - /* - * The total number of segments is the configuration value plus 2 - * since the IOCB need a command and response bde. - */ - phba->cfg_sg_seg_cnt = LPFC_SG_SEG_CNT + 2; + lpfc_sg_seg_cnt_init(phba, lpfc_sg_seg_cnt); + /* Also reinitialize the host templates with new values. */ + lpfc_vport_template.sg_tablesize = phba->cfg_sg_seg_cnt; + lpfc_template.sg_tablesize = phba->cfg_sg_seg_cnt; /* * Since the sg_tablesize is module parameter, the sg_dma_buf_size - * used to create the sg_dma_buf_pool must be dynamically calculated + * used to create the sg_dma_buf_pool must be dynamically calculated. + * 2 segments are added since the IOCB needs a command and response bde. */ phba->cfg_sg_dma_buf_size = sizeof(struct fcp_cmnd) + sizeof(struct fcp_rsp) + - (phba->cfg_sg_seg_cnt * sizeof(struct ulp_bde64)); + ((phba->cfg_sg_seg_cnt + 2) * sizeof(struct ulp_bde64)); lpfc_hba_queue_depth_init(phba, lpfc_hba_queue_depth); return; } @@ -2448,5 +2612,6 @@ lpfc_get_vport_cfgparam(struct lpfc_vport *vport) lpfc_discovery_threads_init(vport, lpfc_discovery_threads); lpfc_max_luns_init(vport, lpfc_max_luns); lpfc_scan_down_init(vport, lpfc_scan_down); + lpfc_enable_da_id_init(vport, lpfc_enable_da_id); return; } |