diff options
Diffstat (limited to 'drivers/scsi/mac53c94.h')
| -rw-r--r-- | drivers/scsi/mac53c94.h | 214 |
1 files changed, 214 insertions, 0 deletions
diff --git a/drivers/scsi/mac53c94.h b/drivers/scsi/mac53c94.h new file mode 100644 index 00000000000..1ad24e4f0a8 --- /dev/null +++ b/drivers/scsi/mac53c94.h @@ -0,0 +1,214 @@ +/* + * mac53c94.h: definitions for the driver for the 53c94 SCSI bus adaptor + * found on Power Macintosh computers, controlling the external SCSI chain. + * + * Copyright (C) 1996 Paul Mackerras. + */ +#ifndef _MAC53C94_H +#define _MAC53C94_H + +/* + * Registers in the 53C94 controller. + */ + +struct mac53c94_regs { + unsigned char count_lo; + char pad0[15]; + unsigned char count_mid; + char pad1[15]; + unsigned char fifo; + char pad2[15]; + unsigned char command; + char pad3[15]; + unsigned char status; + char pad4[15]; + unsigned char interrupt; + char pad5[15]; + unsigned char seqstep; + char pad6[15]; + unsigned char flags; + char pad7[15]; + unsigned char config1; + char pad8[15]; + unsigned char clk_factor; + char pad9[15]; + unsigned char test; + char pad10[15]; + unsigned char config2; + char pad11[15]; + unsigned char config3; + char pad12[15]; + unsigned char config4; + char pad13[15]; + unsigned char count_hi; + char pad14[15]; + unsigned char fifo_res; + char pad15[15]; +}; + +/* + * Alternate functions for some registers. + */ +#define dest_id status +#define sel_timeout interrupt +#define sync_period seqstep +#define sync_offset flags + +/* + * Bits in command register. + */ +#define CMD_DMA_MODE 0x80 +#define CMD_MODE_MASK 0x70 +#define CMD_MODE_INIT 0x10 +#define CMD_MODE_TARG 0x20 +#define CMD_MODE_DISC 0x40 + +#define CMD_NOP 0 +#define CMD_FLUSH 1 +#define CMD_RESET 2 +#define CMD_SCSI_RESET 3 + +#define CMD_XFER_DATA 0x10 +#define CMD_I_COMPLETE 0x11 +#define CMD_ACCEPT_MSG 0x12 +#define CMD_XFER_PAD 0x18 +#define CMD_SET_ATN 0x1a +#define CMD_CLR_ATN 0x1b + +#define CMD_SEND_MSG 0x20 +#define CMD_SEND_STATUS 0x21 +#define CMD_SEND_DATA 0x22 +#define CMD_DISC_SEQ 0x23 +#define CMD_TERMINATE 0x24 +#define CMD_T_COMPLETE 0x25 +#define CMD_DISCONNECT 0x27 +#define CMD_RECV_MSG 0x28 +#define CMD_RECV_CDB 0x29 +#define CMD_RECV_DATA 0x2a +#define CMD_RECV_CMD 0x2b +#define CMD_ABORT_DMA 0x04 + +#define CMD_RESELECT 0x40 +#define CMD_SELECT 0x41 +#define CMD_SELECT_ATN 0x42 +#define CMD_SELATN_STOP 0x43 +#define CMD_ENABLE_SEL 0x44 +#define CMD_DISABLE_SEL 0x45 +#define CMD_SEL_ATN3 0x46 +#define CMD_RESEL_ATN3 0x47 + +/* + * Bits in status register. + */ +#define STAT_IRQ 0x80 +#define STAT_ERROR 0x40 +#define STAT_PARITY 0x20 +#define STAT_TC_ZERO 0x10 +#define STAT_DONE 0x08 +#define STAT_PHASE 0x07 +#define STAT_MSG 0x04 +#define STAT_CD 0x02 +#define STAT_IO 0x01 + +/* + * Bits in interrupt register. + */ +#define INTR_RESET 0x80 /* SCSI bus was reset */ +#define INTR_ILL_CMD 0x40 /* illegal command */ +#define INTR_DISCONNECT 0x20 /* we got disconnected */ +#define INTR_BUS_SERV 0x10 /* bus service requested */ +#define INTR_DONE 0x08 /* function completed */ +#define INTR_RESELECTED 0x04 /* we were reselected */ +#define INTR_SEL_ATN 0x02 /* we were selected, ATN asserted */ +#define INTR_SELECT 0x01 /* we were selected, ATN negated */ + +/* + * Encoding for the select timeout. + */ +#define TIMO_VAL(x) ((x) * 5000 / 7682) + +/* + * Bits in sequence step register. + */ +#define SS_MASK 7 +#define SS_ARB_SEL 0 /* Selection & arbitration complete */ +#define SS_MSG_SENT 1 /* One message byte sent */ +#define SS_NOT_CMD 2 /* Not in command phase */ +#define SS_PHASE_CHG 3 /* Early phase change, cmd bytes lost */ +#define SS_DONE 4 /* Command was sent OK */ + +/* + * Encoding for sync transfer period. + */ +#define SYNCP_MASK 0x1f +#define SYNCP_MIN 4 +#define SYNCP_MAX 31 + +/* + * Bits in flags register. + */ +#define FLAGS_FIFO_LEV 0x1f +#define FLAGS_SEQ_STEP 0xe0 + +/* + * Encoding for sync offset. + */ +#define SYNCO_MASK 0x0f +#define SYNCO_ASS_CTRL 0x30 /* REQ/ACK assertion control */ +#define SYNCO_NEG_CTRL 0xc0 /* REQ/ACK negation control */ + +/* + * Bits in config1 register. + */ +#define CF1_SLOW_CABLE 0x80 /* Slow cable mode */ +#define CF1_NO_RES_REP 0x40 /* Disable SCSI reset reports */ +#define CF1_PAR_TEST 0x20 /* Parity test mode enable */ +#define CF1_PAR_ENABLE 0x10 /* Enable parity checks */ +#define CF1_TEST 0x08 /* Chip tests */ +#define CF1_MY_ID 0x07 /* Controller's address on bus */ + +/* + * Encoding for clk_factor register. + */ +#define CLKF_MASK 7 +#define CLKF_VAL(freq) ((((freq) + 4999999) / 5000000) & CLKF_MASK) + +/* + * Bits in test mode register. + */ +#define TEST_TARGET 1 /* target test mode */ +#define TEST_INITIATOR 2 /* initiator test mode */ +#define TEST_TRISTATE 4 /* tristate (hi-z) test mode */ + +/* + * Bits in config2 register. + */ +#define CF2_RFB 0x80 +#define CF2_FEATURE_EN 0x40 /* enable features / phase latch */ +#define CF2_BYTECTRL 0x20 +#define CF2_DREQ_HIZ 0x10 +#define CF2_SCSI2 0x08 +#define CF2_PAR_ABORT 0x04 /* bad parity target abort */ +#define CF2_REG_PARERR 0x02 /* register parity error */ +#define CF2_DMA_PARERR 0x01 /* DMA parity error */ + +/* + * Bits in the config3 register. + */ +#define CF3_ID_MSG_CHK 0x80 +#define CF3_3B_MSGS 0x40 +#define CF3_CDB10 0x20 +#define CF3_FASTSCSI 0x10 /* enable fast SCSI support */ +#define CF3_FASTCLOCK 0x08 +#define CF3_SAVERESID 0x04 +#define CF3_ALT_DMA 0x02 +#define CF3_THRESH_8 0x01 + +/* + * Bits in the config4 register. + */ +#define CF4_EAN 0x04 +#define CF4_TEST 0x02 +#define CF4_BBTE 0x01 + +#endif /* _MAC53C94_H */ |