diff options
Diffstat (limited to 'drivers/scsi/pm8001/pm8001_hwi.c')
| -rw-r--r-- | drivers/scsi/pm8001/pm8001_hwi.c | 4371 |
1 files changed, 4371 insertions, 0 deletions
diff --git a/drivers/scsi/pm8001/pm8001_hwi.c b/drivers/scsi/pm8001/pm8001_hwi.c new file mode 100644 index 00000000000..aa5756fe057 --- /dev/null +++ b/drivers/scsi/pm8001/pm8001_hwi.c @@ -0,0 +1,4371 @@ +/* + * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver + * + * Copyright (c) 2008-2009 USI Co., Ltd. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + */ + #include "pm8001_sas.h" + #include "pm8001_hwi.h" + #include "pm8001_chips.h" + #include "pm8001_ctl.h" + +/** + * read_main_config_table - read the configure table and save it. + * @pm8001_ha: our hba card information + */ +static void __devinit read_main_config_table(struct pm8001_hba_info *pm8001_ha) +{ + void __iomem *address = pm8001_ha->main_cfg_tbl_addr; + pm8001_ha->main_cfg_tbl.signature = pm8001_mr32(address, 0x00); + pm8001_ha->main_cfg_tbl.interface_rev = pm8001_mr32(address, 0x04); + pm8001_ha->main_cfg_tbl.firmware_rev = pm8001_mr32(address, 0x08); + pm8001_ha->main_cfg_tbl.max_out_io = pm8001_mr32(address, 0x0C); + pm8001_ha->main_cfg_tbl.max_sgl = pm8001_mr32(address, 0x10); + pm8001_ha->main_cfg_tbl.ctrl_cap_flag = pm8001_mr32(address, 0x14); + pm8001_ha->main_cfg_tbl.gst_offset = pm8001_mr32(address, 0x18); + pm8001_ha->main_cfg_tbl.inbound_queue_offset = + pm8001_mr32(address, 0x1C); + pm8001_ha->main_cfg_tbl.outbound_queue_offset = + pm8001_mr32(address, 0x20); + pm8001_ha->main_cfg_tbl.hda_mode_flag = + pm8001_mr32(address, MAIN_HDA_FLAGS_OFFSET); + + /* read analog Setting offset from the configuration table */ + pm8001_ha->main_cfg_tbl.anolog_setup_table_offset = + pm8001_mr32(address, MAIN_ANALOG_SETUP_OFFSET); + + /* read Error Dump Offset and Length */ + pm8001_ha->main_cfg_tbl.fatal_err_dump_offset0 = + pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_OFFSET); + pm8001_ha->main_cfg_tbl.fatal_err_dump_length0 = + pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP0_LENGTH); + pm8001_ha->main_cfg_tbl.fatal_err_dump_offset1 = + pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_OFFSET); + pm8001_ha->main_cfg_tbl.fatal_err_dump_length1 = + pm8001_mr32(address, MAIN_FATAL_ERROR_RDUMP1_LENGTH); +} + +/** + * read_general_status_table - read the general status table and save it. + * @pm8001_ha: our hba card information + */ +static void __devinit +read_general_status_table(struct pm8001_hba_info *pm8001_ha) +{ + void __iomem *address = pm8001_ha->general_stat_tbl_addr; + pm8001_ha->gs_tbl.gst_len_mpistate = pm8001_mr32(address, 0x00); + pm8001_ha->gs_tbl.iq_freeze_state0 = pm8001_mr32(address, 0x04); + pm8001_ha->gs_tbl.iq_freeze_state1 = pm8001_mr32(address, 0x08); + pm8001_ha->gs_tbl.msgu_tcnt = pm8001_mr32(address, 0x0C); + pm8001_ha->gs_tbl.iop_tcnt = pm8001_mr32(address, 0x10); + pm8001_ha->gs_tbl.reserved = pm8001_mr32(address, 0x14); + pm8001_ha->gs_tbl.phy_state[0] = pm8001_mr32(address, 0x18); + pm8001_ha->gs_tbl.phy_state[1] = pm8001_mr32(address, 0x1C); + pm8001_ha->gs_tbl.phy_state[2] = pm8001_mr32(address, 0x20); + pm8001_ha->gs_tbl.phy_state[3] = pm8001_mr32(address, 0x24); + pm8001_ha->gs_tbl.phy_state[4] = pm8001_mr32(address, 0x28); + pm8001_ha->gs_tbl.phy_state[5] = pm8001_mr32(address, 0x2C); + pm8001_ha->gs_tbl.phy_state[6] = pm8001_mr32(address, 0x30); + pm8001_ha->gs_tbl.phy_state[7] = pm8001_mr32(address, 0x34); + pm8001_ha->gs_tbl.reserved1 = pm8001_mr32(address, 0x38); + pm8001_ha->gs_tbl.reserved2 = pm8001_mr32(address, 0x3C); + pm8001_ha->gs_tbl.reserved3 = pm8001_mr32(address, 0x40); + pm8001_ha->gs_tbl.recover_err_info[0] = pm8001_mr32(address, 0x44); + pm8001_ha->gs_tbl.recover_err_info[1] = pm8001_mr32(address, 0x48); + pm8001_ha->gs_tbl.recover_err_info[2] = pm8001_mr32(address, 0x4C); + pm8001_ha->gs_tbl.recover_err_info[3] = pm8001_mr32(address, 0x50); + pm8001_ha->gs_tbl.recover_err_info[4] = pm8001_mr32(address, 0x54); + pm8001_ha->gs_tbl.recover_err_info[5] = pm8001_mr32(address, 0x58); + pm8001_ha->gs_tbl.recover_err_info[6] = pm8001_mr32(address, 0x5C); + pm8001_ha->gs_tbl.recover_err_info[7] = pm8001_mr32(address, 0x60); +} + +/** + * read_inbnd_queue_table - read the inbound queue table and save it. + * @pm8001_ha: our hba card information + */ +static void __devinit +read_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha) +{ + int inbQ_num = 1; + int i; + void __iomem *address = pm8001_ha->inbnd_q_tbl_addr; + for (i = 0; i < inbQ_num; i++) { + u32 offset = i * 0x24; + pm8001_ha->inbnd_q_tbl[i].pi_pci_bar = + get_pci_bar_index(pm8001_mr32(address, (offset + 0x14))); + pm8001_ha->inbnd_q_tbl[i].pi_offset = + pm8001_mr32(address, (offset + 0x18)); + } +} + +/** + * read_outbnd_queue_table - read the outbound queue table and save it. + * @pm8001_ha: our hba card information + */ +static void __devinit +read_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha) +{ + int outbQ_num = 1; + int i; + void __iomem *address = pm8001_ha->outbnd_q_tbl_addr; + for (i = 0; i < outbQ_num; i++) { + u32 offset = i * 0x24; + pm8001_ha->outbnd_q_tbl[i].ci_pci_bar = + get_pci_bar_index(pm8001_mr32(address, (offset + 0x14))); + pm8001_ha->outbnd_q_tbl[i].ci_offset = + pm8001_mr32(address, (offset + 0x18)); + } +} + +/** + * init_default_table_values - init the default table. + * @pm8001_ha: our hba card information + */ +static void __devinit +init_default_table_values(struct pm8001_hba_info *pm8001_ha) +{ + int qn = 1; + int i; + u32 offsetib, offsetob; + void __iomem *addressib = pm8001_ha->inbnd_q_tbl_addr; + void __iomem *addressob = pm8001_ha->outbnd_q_tbl_addr; + + pm8001_ha->main_cfg_tbl.inbound_q_nppd_hppd = 0; + pm8001_ha->main_cfg_tbl.outbound_hw_event_pid0_3 = 0; + pm8001_ha->main_cfg_tbl.outbound_hw_event_pid4_7 = 0; + pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid0_3 = 0; + pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid4_7 = 0; + pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid0_3 = 0; + pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid4_7 = 0; + pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid0_3 = 0; + pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid4_7 = 0; + pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid0_3 = 0; + pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid4_7 = 0; + + pm8001_ha->main_cfg_tbl.upper_event_log_addr = + pm8001_ha->memoryMap.region[AAP1].phys_addr_hi; + pm8001_ha->main_cfg_tbl.lower_event_log_addr = + pm8001_ha->memoryMap.region[AAP1].phys_addr_lo; + pm8001_ha->main_cfg_tbl.event_log_size = PM8001_EVENT_LOG_SIZE; + pm8001_ha->main_cfg_tbl.event_log_option = 0x01; + pm8001_ha->main_cfg_tbl.upper_iop_event_log_addr = + pm8001_ha->memoryMap.region[IOP].phys_addr_hi; + pm8001_ha->main_cfg_tbl.lower_iop_event_log_addr = + pm8001_ha->memoryMap.region[IOP].phys_addr_lo; + pm8001_ha->main_cfg_tbl.iop_event_log_size = PM8001_EVENT_LOG_SIZE; + pm8001_ha->main_cfg_tbl.iop_event_log_option = 0x01; + pm8001_ha->main_cfg_tbl.fatal_err_interrupt = 0x01; + for (i = 0; i < qn; i++) { + pm8001_ha->inbnd_q_tbl[i].element_pri_size_cnt = + 0x00000100 | (0x00000040 << 16) | (0x00<<30); + pm8001_ha->inbnd_q_tbl[i].upper_base_addr = + pm8001_ha->memoryMap.region[IB].phys_addr_hi; + pm8001_ha->inbnd_q_tbl[i].lower_base_addr = + pm8001_ha->memoryMap.region[IB].phys_addr_lo; + pm8001_ha->inbnd_q_tbl[i].base_virt = + (u8 *)pm8001_ha->memoryMap.region[IB].virt_ptr; + pm8001_ha->inbnd_q_tbl[i].total_length = + pm8001_ha->memoryMap.region[IB].total_len; + pm8001_ha->inbnd_q_tbl[i].ci_upper_base_addr = + pm8001_ha->memoryMap.region[CI].phys_addr_hi; + pm8001_ha->inbnd_q_tbl[i].ci_lower_base_addr = + pm8001_ha->memoryMap.region[CI].phys_addr_lo; + pm8001_ha->inbnd_q_tbl[i].ci_virt = + pm8001_ha->memoryMap.region[CI].virt_ptr; + offsetib = i * 0x20; + pm8001_ha->inbnd_q_tbl[i].pi_pci_bar = + get_pci_bar_index(pm8001_mr32(addressib, + (offsetib + 0x14))); + pm8001_ha->inbnd_q_tbl[i].pi_offset = + pm8001_mr32(addressib, (offsetib + 0x18)); + pm8001_ha->inbnd_q_tbl[i].producer_idx = 0; + pm8001_ha->inbnd_q_tbl[i].consumer_index = 0; + } + for (i = 0; i < qn; i++) { + pm8001_ha->outbnd_q_tbl[i].element_size_cnt = + 256 | (64 << 16) | (1<<30); + pm8001_ha->outbnd_q_tbl[i].upper_base_addr = + pm8001_ha->memoryMap.region[OB].phys_addr_hi; + pm8001_ha->outbnd_q_tbl[i].lower_base_addr = + pm8001_ha->memoryMap.region[OB].phys_addr_lo; + pm8001_ha->outbnd_q_tbl[i].base_virt = + (u8 *)pm8001_ha->memoryMap.region[OB].virt_ptr; + pm8001_ha->outbnd_q_tbl[i].total_length = + pm8001_ha->memoryMap.region[OB].total_len; + pm8001_ha->outbnd_q_tbl[i].pi_upper_base_addr = + pm8001_ha->memoryMap.region[PI].phys_addr_hi; + pm8001_ha->outbnd_q_tbl[i].pi_lower_base_addr = + pm8001_ha->memoryMap.region[PI].phys_addr_lo; + pm8001_ha->outbnd_q_tbl[i].interrup_vec_cnt_delay = + 0 | (0 << 16) | (0 << 24); + pm8001_ha->outbnd_q_tbl[i].pi_virt = + pm8001_ha->memoryMap.region[PI].virt_ptr; + offsetob = i * 0x24; + pm8001_ha->outbnd_q_tbl[i].ci_pci_bar = + get_pci_bar_index(pm8001_mr32(addressob, + offsetob + 0x14)); + pm8001_ha->outbnd_q_tbl[i].ci_offset = + pm8001_mr32(addressob, (offsetob + 0x18)); + pm8001_ha->outbnd_q_tbl[i].consumer_idx = 0; + pm8001_ha->outbnd_q_tbl[i].producer_index = 0; + } +} + +/** + * update_main_config_table - update the main default table to the HBA. + * @pm8001_ha: our hba card information + */ +static void __devinit +update_main_config_table(struct pm8001_hba_info *pm8001_ha) +{ + void __iomem *address = pm8001_ha->main_cfg_tbl_addr; + pm8001_mw32(address, 0x24, + pm8001_ha->main_cfg_tbl.inbound_q_nppd_hppd); + pm8001_mw32(address, 0x28, + pm8001_ha->main_cfg_tbl.outbound_hw_event_pid0_3); + pm8001_mw32(address, 0x2C, + pm8001_ha->main_cfg_tbl.outbound_hw_event_pid4_7); + pm8001_mw32(address, 0x30, + pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid0_3); + pm8001_mw32(address, 0x34, + pm8001_ha->main_cfg_tbl.outbound_ncq_event_pid4_7); + pm8001_mw32(address, 0x38, + pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid0_3); + pm8001_mw32(address, 0x3C, + pm8001_ha->main_cfg_tbl.outbound_tgt_ITNexus_event_pid4_7); + pm8001_mw32(address, 0x40, + pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid0_3); + pm8001_mw32(address, 0x44, + pm8001_ha->main_cfg_tbl.outbound_tgt_ssp_event_pid4_7); + pm8001_mw32(address, 0x48, + pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid0_3); + pm8001_mw32(address, 0x4C, + pm8001_ha->main_cfg_tbl.outbound_tgt_smp_event_pid4_7); + pm8001_mw32(address, 0x50, + pm8001_ha->main_cfg_tbl.upper_event_log_addr); + pm8001_mw32(address, 0x54, + pm8001_ha->main_cfg_tbl.lower_event_log_addr); + pm8001_mw32(address, 0x58, pm8001_ha->main_cfg_tbl.event_log_size); + pm8001_mw32(address, 0x5C, pm8001_ha->main_cfg_tbl.event_log_option); + pm8001_mw32(address, 0x60, + pm8001_ha->main_cfg_tbl.upper_iop_event_log_addr); + pm8001_mw32(address, 0x64, + pm8001_ha->main_cfg_tbl.lower_iop_event_log_addr); + pm8001_mw32(address, 0x68, pm8001_ha->main_cfg_tbl.iop_event_log_size); + pm8001_mw32(address, 0x6C, + pm8001_ha->main_cfg_tbl.iop_event_log_option); + pm8001_mw32(address, 0x70, + pm8001_ha->main_cfg_tbl.fatal_err_interrupt); +} + +/** + * update_inbnd_queue_table - update the inbound queue table to the HBA. + * @pm8001_ha: our hba card information + */ +static void __devinit +update_inbnd_queue_table(struct pm8001_hba_info *pm8001_ha, int number) +{ + void __iomem *address = pm8001_ha->inbnd_q_tbl_addr; + u16 offset = number * 0x20; + pm8001_mw32(address, offset + 0x00, + pm8001_ha->inbnd_q_tbl[number].element_pri_size_cnt); + pm8001_mw32(address, offset + 0x04, + pm8001_ha->inbnd_q_tbl[number].upper_base_addr); + pm8001_mw32(address, offset + 0x08, + pm8001_ha->inbnd_q_tbl[number].lower_base_addr); + pm8001_mw32(address, offset + 0x0C, + pm8001_ha->inbnd_q_tbl[number].ci_upper_base_addr); + pm8001_mw32(address, offset + 0x10, + pm8001_ha->inbnd_q_tbl[number].ci_lower_base_addr); +} + +/** + * update_outbnd_queue_table - update the outbound queue table to the HBA. + * @pm8001_ha: our hba card information + */ +static void __devinit +update_outbnd_queue_table(struct pm8001_hba_info *pm8001_ha, int number) +{ + void __iomem *address = pm8001_ha->outbnd_q_tbl_addr; + u16 offset = number * 0x24; + pm8001_mw32(address, offset + 0x00, + pm8001_ha->outbnd_q_tbl[number].element_size_cnt); + pm8001_mw32(address, offset + 0x04, + pm8001_ha->outbnd_q_tbl[number].upper_base_addr); + pm8001_mw32(address, offset + 0x08, + pm8001_ha->outbnd_q_tbl[number].lower_base_addr); + pm8001_mw32(address, offset + 0x0C, + pm8001_ha->outbnd_q_tbl[number].pi_upper_base_addr); + pm8001_mw32(address, offset + 0x10, + pm8001_ha->outbnd_q_tbl[number].pi_lower_base_addr); + pm8001_mw32(address, offset + 0x1C, + pm8001_ha->outbnd_q_tbl[number].interrup_vec_cnt_delay); +} + +/** + * bar4_shift - function is called to shift BAR base address + * @pm8001_ha : our hba card infomation + * @shiftValue : shifting value in memory bar. + */ +static u32 bar4_shift(struct pm8001_hba_info *pm8001_ha, u32 shiftValue) +{ + u32 regVal; + u32 max_wait_count; + + /* program the inbound AXI translation Lower Address */ + pm8001_cw32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW, shiftValue); + + /* confirm the setting is written */ + max_wait_count = 1 * 1000 * 1000; /* 1 sec */ + do { + udelay(1); + regVal = pm8001_cr32(pm8001_ha, 1, SPC_IBW_AXI_TRANSLATION_LOW); + } while ((regVal != shiftValue) && (--max_wait_count)); + + if (!max_wait_count) { + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("TIMEOUT:SPC_IBW_AXI_TRANSLATION_LOW" + " = 0x%x\n", regVal)); + return -1; + } + return 0; +} + +/** + * mpi_set_phys_g3_with_ssc + * @pm8001_ha: our hba card information + * @SSCbit: set SSCbit to 0 to disable all phys ssc; 1 to enable all phys ssc. + */ +static void __devinit +mpi_set_phys_g3_with_ssc(struct pm8001_hba_info *pm8001_ha, u32 SSCbit) +{ + u32 offset; + u32 value; + u32 i; + +#define SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR 0x00030000 +#define SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR 0x00040000 +#define SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET 0x1074 +#define SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET 0x1074 +#define PHY_SSC_BIT_SHIFT 13 + + /* + * Using shifted destination address 0x3_0000:0x1074 + 0x4000*N (N=0:3) + * Using shifted destination address 0x4_0000:0x1074 + 0x4000*(N-4) (N=4:7) + */ + if (-1 == bar4_shift(pm8001_ha, SAS2_SETTINGS_LOCAL_PHY_0_3_SHIFT_ADDR)) + return; + /* set SSC bit of PHY 0 - 3 */ + for (i = 0; i < 4; i++) { + offset = SAS2_SETTINGS_LOCAL_PHY_0_3_OFFSET + 0x4000 * i; + value = pm8001_cr32(pm8001_ha, 2, offset); + if (SSCbit) + value = value | (0x00000001 << PHY_SSC_BIT_SHIFT); + else + value = value & (~(0x00000001<<PHY_SSC_BIT_SHIFT)); + pm8001_cw32(pm8001_ha, 2, offset, value); + } + + /* shift membase 3 for SAS2_SETTINGS_LOCAL_PHY 4 - 7 */ + if (-1 == bar4_shift(pm8001_ha, SAS2_SETTINGS_LOCAL_PHY_4_7_SHIFT_ADDR)) + return; + + /* set SSC bit of PHY 4 - 7 */ + for (i = 4; i < 8; i++) { + offset = SAS2_SETTINGS_LOCAL_PHY_4_7_OFFSET + 0x4000 * (i-4); + value = pm8001_cr32(pm8001_ha, 2, offset); + if (SSCbit) + value = value | (0x00000001 << PHY_SSC_BIT_SHIFT); + else + value = value & (~(0x00000001<<PHY_SSC_BIT_SHIFT)); + pm8001_cw32(pm8001_ha, 2, offset, value); + } + + /*set the shifted destination address to 0x0 to avoid error operation */ + bar4_shift(pm8001_ha, 0x0); + return; +} + +/** + * mpi_set_open_retry_interval_reg + * @pm8001_ha: our hba card information + * @interval - interval time for each OPEN_REJECT (RETRY). The units are in 1us. + */ +static void __devinit +mpi_set_open_retry_interval_reg(struct pm8001_hba_info *pm8001_ha, + u32 interval) +{ + u32 offset; + u32 value; + u32 i; + +#define OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR 0x00030000 +#define OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR 0x00040000 +#define OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET 0x30B4 +#define OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET 0x30B4 +#define OPEN_RETRY_INTERVAL_REG_MASK 0x0000FFFF + + value = interval & OPEN_RETRY_INTERVAL_REG_MASK; + /* shift bar and set the OPEN_REJECT(RETRY) interval time of PHY 0 -3.*/ + if (-1 == bar4_shift(pm8001_ha, + OPEN_RETRY_INTERVAL_PHY_0_3_SHIFT_ADDR)) + return; + for (i = 0; i < 4; i++) { + offset = OPEN_RETRY_INTERVAL_PHY_0_3_OFFSET + 0x4000 * i; + pm8001_cw32(pm8001_ha, 2, offset, value); + } + + if (-1 == bar4_shift(pm8001_ha, + OPEN_RETRY_INTERVAL_PHY_4_7_SHIFT_ADDR)) + return; + for (i = 4; i < 8; i++) { + offset = OPEN_RETRY_INTERVAL_PHY_4_7_OFFSET + 0x4000 * (i-4); + pm8001_cw32(pm8001_ha, 2, offset, value); + } + /*set the shifted destination address to 0x0 to avoid error operation */ + bar4_shift(pm8001_ha, 0x0); + return; +} + +/** + * mpi_init_check - check firmware initialization status. + * @pm8001_ha: our hba card information + */ +static int mpi_init_check(struct pm8001_hba_info *pm8001_ha) +{ + u32 max_wait_count; + u32 value; + u32 gst_len_mpistate; + /* Write bit0=1 to Inbound DoorBell Register to tell the SPC FW the + table is updated */ + pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_UPDATE); + /* wait until Inbound DoorBell Clear Register toggled */ + max_wait_count = 1 * 1000 * 1000;/* 1 sec */ + do { + udelay(1); + value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET); + value &= SPC_MSGU_CFG_TABLE_UPDATE; + } while ((value != 0) && (--max_wait_count)); + + if (!max_wait_count) + return -1; + /* check the MPI-State for initialization */ + gst_len_mpistate = + pm8001_mr32(pm8001_ha->general_stat_tbl_addr, + GST_GSTLEN_MPIS_OFFSET); + if (GST_MPI_STATE_INIT != (gst_len_mpistate & GST_MPI_STATE_MASK)) + return -1; + /* check MPI Initialization error */ + gst_len_mpistate = gst_len_mpistate >> 16; + if (0x0000 != gst_len_mpistate) + return -1; + return 0; +} + +/** + * check_fw_ready - The LLDD check if the FW is ready, if not, return error. + * @pm8001_ha: our hba card information + */ +static int check_fw_ready(struct pm8001_hba_info *pm8001_ha) +{ + u32 value, value1; + u32 max_wait_count; + /* check error state */ + value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1); + value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2); + /* check AAP error */ + if (SCRATCH_PAD1_ERR == (value & SCRATCH_PAD_STATE_MASK)) { + /* error state */ + value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0); + return -1; + } + + /* check IOP error */ + if (SCRATCH_PAD2_ERR == (value1 & SCRATCH_PAD_STATE_MASK)) { + /* error state */ + value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3); + return -1; + } + + /* bit 4-31 of scratch pad1 should be zeros if it is not + in error state*/ + if (value & SCRATCH_PAD1_STATE_MASK) { + /* error case */ + pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0); + return -1; + } + + /* bit 2, 4-31 of scratch pad2 should be zeros if it is not + in error state */ + if (value1 & SCRATCH_PAD2_STATE_MASK) { + /* error case */ + return -1; + } + + max_wait_count = 1 * 1000 * 1000;/* 1 sec timeout */ + + /* wait until scratch pad 1 and 2 registers in ready state */ + do { + udelay(1); + value = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1) + & SCRATCH_PAD1_RDY; + value1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2) + & SCRATCH_PAD2_RDY; + if ((--max_wait_count) == 0) + return -1; + } while ((value != SCRATCH_PAD1_RDY) || (value1 != SCRATCH_PAD2_RDY)); + return 0; +} + +static void init_pci_device_addresses(struct pm8001_hba_info *pm8001_ha) +{ + void __iomem *base_addr; + u32 value; + u32 offset; + u32 pcibar; + u32 pcilogic; + + value = pm8001_cr32(pm8001_ha, 0, 0x44); + offset = value & 0x03FFFFFF; + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("Scratchpad 0 Offset: %x \n", offset)); + pcilogic = (value & 0xFC000000) >> 26; + pcibar = get_pci_bar_index(pcilogic); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("Scratchpad 0 PCI BAR: %d \n", pcibar)); + pm8001_ha->main_cfg_tbl_addr = base_addr = + pm8001_ha->io_mem[pcibar].memvirtaddr + offset; + pm8001_ha->general_stat_tbl_addr = + base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x18); + pm8001_ha->inbnd_q_tbl_addr = + base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x1C); + pm8001_ha->outbnd_q_tbl_addr = + base_addr + pm8001_cr32(pm8001_ha, pcibar, offset + 0x20); +} + +/** + * pm8001_chip_init - the main init function that initialize whole PM8001 chip. + * @pm8001_ha: our hba card information + */ +static int __devinit pm8001_chip_init(struct pm8001_hba_info *pm8001_ha) +{ + /* check the firmware status */ + if (-1 == check_fw_ready(pm8001_ha)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Firmware is not ready!\n")); + return -EBUSY; + } + + /* Initialize pci space address eg: mpi offset */ + init_pci_device_addresses(pm8001_ha); + init_default_table_values(pm8001_ha); + read_main_config_table(pm8001_ha); + read_general_status_table(pm8001_ha); + read_inbnd_queue_table(pm8001_ha); + read_outbnd_queue_table(pm8001_ha); + /* update main config table ,inbound table and outbound table */ + update_main_config_table(pm8001_ha); + update_inbnd_queue_table(pm8001_ha, 0); + update_outbnd_queue_table(pm8001_ha, 0); + mpi_set_phys_g3_with_ssc(pm8001_ha, 0); + mpi_set_open_retry_interval_reg(pm8001_ha, 7); + /* notify firmware update finished and check initialization status */ + if (0 == mpi_init_check(pm8001_ha)) { + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("MPI initialize successful!\n")); + } else + return -EBUSY; + /*This register is a 16-bit timer with a resolution of 1us. This is the + timer used for interrupt delay/coalescing in the PCIe Application Layer. + Zero is not a valid value. A value of 1 in the register will cause the + interrupts to be normal. A value greater than 1 will cause coalescing + delays.*/ + pm8001_cw32(pm8001_ha, 1, 0x0033c0, 0x1); + pm8001_cw32(pm8001_ha, 1, 0x0033c4, 0x0); + return 0; +} + +static int mpi_uninit_check(struct pm8001_hba_info *pm8001_ha) +{ + u32 max_wait_count; + u32 value; + u32 gst_len_mpistate; + init_pci_device_addresses(pm8001_ha); + /* Write bit1=1 to Inbound DoorBell Register to tell the SPC FW the + table is stop */ + pm8001_cw32(pm8001_ha, 0, MSGU_IBDB_SET, SPC_MSGU_CFG_TABLE_RESET); + + /* wait until Inbound DoorBell Clear Register toggled */ + max_wait_count = 1 * 1000 * 1000;/* 1 sec */ + do { + udelay(1); + value = pm8001_cr32(pm8001_ha, 0, MSGU_IBDB_SET); + value &= SPC_MSGU_CFG_TABLE_RESET; + } while ((value != 0) && (--max_wait_count)); + + if (!max_wait_count) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("TIMEOUT:IBDB value/=0x%x\n", value)); + return -1; + } + + /* check the MPI-State for termination in progress */ + /* wait until Inbound DoorBell Clear Register toggled */ + max_wait_count = 1 * 1000 * 1000; /* 1 sec */ + do { + udelay(1); + gst_len_mpistate = + pm8001_mr32(pm8001_ha->general_stat_tbl_addr, + GST_GSTLEN_MPIS_OFFSET); + if (GST_MPI_STATE_UNINIT == + (gst_len_mpistate & GST_MPI_STATE_MASK)) + break; + } while (--max_wait_count); + if (!max_wait_count) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk(" TIME OUT MPI State = 0x%x\n", + gst_len_mpistate & GST_MPI_STATE_MASK)); + return -1; + } + return 0; +} + +/** + * soft_reset_ready_check - Function to check FW is ready for soft reset. + * @pm8001_ha: our hba card information + */ +static u32 soft_reset_ready_check(struct pm8001_hba_info *pm8001_ha) +{ + u32 regVal, regVal1, regVal2; + if (mpi_uninit_check(pm8001_ha) != 0) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("MPI state is not ready\n")); + return -1; + } + /* read the scratch pad 2 register bit 2 */ + regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2) + & SCRATCH_PAD2_FWRDY_RST; + if (regVal == SCRATCH_PAD2_FWRDY_RST) { + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("Firmware is ready for reset .\n")); + } else { + /* Trigger NMI twice via RB6 */ + if (-1 == bar4_shift(pm8001_ha, RB6_ACCESS_REG)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Shift Bar4 to 0x%x failed\n", + RB6_ACCESS_REG)); + return -1; + } + pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET, + RB6_MAGIC_NUMBER_RST); + pm8001_cw32(pm8001_ha, 2, SPC_RB6_OFFSET, RB6_MAGIC_NUMBER_RST); + /* wait for 100 ms */ + mdelay(100); + regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2) & + SCRATCH_PAD2_FWRDY_RST; + if (regVal != SCRATCH_PAD2_FWRDY_RST) { + regVal1 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1); + regVal2 = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("TIMEOUT:MSGU_SCRATCH_PAD1" + "=0x%x, MSGU_SCRATCH_PAD2=0x%x\n", + regVal1, regVal2)); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("SCRATCH_PAD0 value = 0x%x\n", + pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_0))); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("SCRATCH_PAD3 value = 0x%x\n", + pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_3))); + return -1; + } + } + return 0; +} + +/** + * pm8001_chip_soft_rst - soft reset the PM8001 chip, so that the clear all + * the FW register status to the originated status. + * @pm8001_ha: our hba card information + * @signature: signature in host scratch pad0 register. + */ +static int +pm8001_chip_soft_rst(struct pm8001_hba_info *pm8001_ha, u32 signature) +{ + u32 regVal, toggleVal; + u32 max_wait_count; + u32 regVal1, regVal2, regVal3; + + /* step1: Check FW is ready for soft reset */ + if (soft_reset_ready_check(pm8001_ha) != 0) { + PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("FW is not ready\n")); + return -1; + } + + /* step 2: clear NMI status register on AAP1 and IOP, write the same + value to clear */ + /* map 0x60000 to BAR4(0x20), BAR2(win) */ + if (-1 == bar4_shift(pm8001_ha, MBIC_AAP1_ADDR_BASE)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Shift Bar4 to 0x%x failed\n", + MBIC_AAP1_ADDR_BASE)); + return -1; + } + regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("MBIC - NMI Enable VPE0 (IOP)= 0x%x\n", regVal)); + pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_IOP, 0x0); + /* map 0x70000 to BAR4(0x20), BAR2(win) */ + if (-1 == bar4_shift(pm8001_ha, MBIC_IOP_ADDR_BASE)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Shift Bar4 to 0x%x failed\n", + MBIC_IOP_ADDR_BASE)); + return -1; + } + regVal = pm8001_cr32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("MBIC - NMI Enable VPE0 (AAP1)= 0x%x\n", regVal)); + pm8001_cw32(pm8001_ha, 2, MBIC_NMI_ENABLE_VPE0_AAP1, 0x0); + + regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("PCIE -Event Interrupt Enable = 0x%x\n", regVal)); + pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT_ENABLE, 0x0); + + regVal = pm8001_cr32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("PCIE - Event Interrupt = 0x%x\n", regVal)); + pm8001_cw32(pm8001_ha, 1, PCIE_EVENT_INTERRUPT, regVal); + + regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("PCIE -Error Interrupt Enable = 0x%x\n", regVal)); + pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT_ENABLE, 0x0); + + regVal = pm8001_cr32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("PCIE - Error Interrupt = 0x%x\n", regVal)); + pm8001_cw32(pm8001_ha, 1, PCIE_ERROR_INTERRUPT, regVal); + + /* read the scratch pad 1 register bit 2 */ + regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1) + & SCRATCH_PAD1_RST; + toggleVal = regVal ^ SCRATCH_PAD1_RST; + + /* set signature in host scratch pad0 register to tell SPC that the + host performs the soft reset */ + pm8001_cw32(pm8001_ha, 0, MSGU_HOST_SCRATCH_PAD_0, signature); + + /* read required registers for confirmming */ + /* map 0x0700000 to BAR4(0x20), BAR2(win) */ + if (-1 == bar4_shift(pm8001_ha, GSM_ADDR_BASE)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Shift Bar4 to 0x%x failed\n", + GSM_ADDR_BASE)); + return -1; + } + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x0(0x00007b88)-GSM Configuration and" + " Reset = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET))); + + /* step 3: host read GSM Configuration and Reset register */ + regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET); + /* Put those bits to low */ + /* GSM XCBI offset = 0x70 0000 + 0x00 Bit 13 COM_SLV_SW_RSTB 1 + 0x00 Bit 12 QSSP_SW_RSTB 1 + 0x00 Bit 11 RAAE_SW_RSTB 1 + 0x00 Bit 9 RB_1_SW_RSTB 1 + 0x00 Bit 8 SM_SW_RSTB 1 + */ + regVal &= ~(0x00003b00); + /* host write GSM Configuration and Reset register */ + pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x0 (0x00007b88 ==> 0x00004088) - GSM " + "Configuration and Reset is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET))); + + /* step 4: */ + /* disable GSM - Read Address Parity Check */ + regVal1 = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700038 - Read Address Parity Check " + "Enable = 0x%x\n", regVal1)); + pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, 0x0); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable" + "is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK))); + + /* disable GSM - Write Address Parity Check */ + regVal2 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700040 - Write Address Parity Check" + " Enable = 0x%x\n", regVal2)); + pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, 0x0); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700040 - Write Address Parity Check " + "Enable is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK))); + + /* disable GSM - Write Data Parity Check */ + regVal3 = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x300048 - Write Data Parity Check" + " Enable = 0x%x\n", regVal3)); + pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, 0x0); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x300048 - Write Data Parity Check Enable" + "is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK))); + + /* step 5: delay 10 usec */ + udelay(10); + /* step 5-b: set GPIO-0 output control to tristate anyway */ + if (-1 == bar4_shift(pm8001_ha, GPIO_ADDR_BASE)) { + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("Shift Bar4 to 0x%x failed\n", + GPIO_ADDR_BASE)); + return -1; + } + regVal = pm8001_cr32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GPIO Output Control Register:" + " = 0x%x\n", regVal)); + /* set GPIO-0 output control to tri-state */ + regVal &= 0xFFFFFFFC; + pm8001_cw32(pm8001_ha, 2, GPIO_GPIO_0_0UTPUT_CTL_OFFSET, regVal); + + /* Step 6: Reset the IOP and AAP1 */ + /* map 0x00000 to BAR4(0x20), BAR2(win) */ + if (-1 == bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("SPC Shift Bar4 to 0x%x failed\n", + SPC_TOP_LEVEL_ADDR_BASE)); + return -1; + } + regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("Top Register before resetting IOP/AAP1" + ":= 0x%x\n", regVal)); + regVal &= ~(SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS); + pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal); + + /* step 7: Reset the BDMA/OSSP */ + regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("Top Register before resetting BDMA/OSSP" + ": = 0x%x\n", regVal)); + regVal &= ~(SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP); + pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal); + + /* step 8: delay 10 usec */ + udelay(10); + + /* step 9: bring the BDMA and OSSP out of reset */ + regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("Top Register before bringing up BDMA/OSSP" + ":= 0x%x\n", regVal)); + regVal |= (SPC_REG_RESET_BDMA_CORE | SPC_REG_RESET_OSSP); + pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal); + + /* step 10: delay 10 usec */ + udelay(10); + + /* step 11: reads and sets the GSM Configuration and Reset Register */ + /* map 0x0700000 to BAR4(0x20), BAR2(win) */ + if (-1 == bar4_shift(pm8001_ha, GSM_ADDR_BASE)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("SPC Shift Bar4 to 0x%x failed\n", + GSM_ADDR_BASE)); + return -1; + } + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x0 (0x00007b88)-GSM Configuration and " + "Reset = 0x%x\n", pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET))); + regVal = pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET); + /* Put those bits to high */ + /* GSM XCBI offset = 0x70 0000 + 0x00 Bit 13 COM_SLV_SW_RSTB 1 + 0x00 Bit 12 QSSP_SW_RSTB 1 + 0x00 Bit 11 RAAE_SW_RSTB 1 + 0x00 Bit 9 RB_1_SW_RSTB 1 + 0x00 Bit 8 SM_SW_RSTB 1 + */ + regVal |= (GSM_CONFIG_RESET_VALUE); + pm8001_cw32(pm8001_ha, 2, GSM_CONFIG_RESET, regVal); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM (0x00004088 ==> 0x00007b88) - GSM" + " Configuration and Reset is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_CONFIG_RESET))); + + /* step 12: Restore GSM - Read Address Parity Check */ + regVal = pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK); + /* just for debugging */ + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700038 - Read Address Parity Check Enable" + " = 0x%x\n", regVal)); + pm8001_cw32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK, regVal1); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700038 - Read Address Parity" + " Check Enable is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_READ_ADDR_PARITY_CHECK))); + /* Restore GSM - Write Address Parity Check */ + regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK); + pm8001_cw32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK, regVal2); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700040 - Write Address Parity Check" + " Enable is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_WRITE_ADDR_PARITY_CHECK))); + /* Restore GSM - Write Data Parity Check */ + regVal = pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK); + pm8001_cw32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK, regVal3); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("GSM 0x700048 - Write Data Parity Check Enable" + "is set to = 0x%x\n", + pm8001_cr32(pm8001_ha, 2, GSM_WRITE_DATA_PARITY_CHECK))); + + /* step 13: bring the IOP and AAP1 out of reset */ + /* map 0x00000 to BAR4(0x20), BAR2(win) */ + if (-1 == bar4_shift(pm8001_ha, SPC_TOP_LEVEL_ADDR_BASE)) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Shift Bar4 to 0x%x failed\n", + SPC_TOP_LEVEL_ADDR_BASE)); + return -1; + } + regVal = pm8001_cr32(pm8001_ha, 2, SPC_REG_RESET); + regVal |= (SPC_REG_RESET_PCS_IOP_SS | SPC_REG_RESET_PCS_AAP1_SS); + pm8001_cw32(pm8001_ha, 2, SPC_REG_RESET, regVal); + + /* step 14: delay 10 usec - Normal Mode */ + udelay(10); + /* check Soft Reset Normal mode or Soft Reset HDA mode */ + if (signature == SPC_SOFT_RESET_SIGNATURE) { + /* step 15 (Normal Mode): wait until scratch pad1 register + bit 2 toggled */ + max_wait_count = 2 * 1000 * 1000;/* 2 sec */ + do { + udelay(1); + regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1) & + SCRATCH_PAD1_RST; + } while ((regVal != toggleVal) && (--max_wait_count)); + + if (!max_wait_count) { + regVal = pm8001_cr32(pm8001_ha, 0, + MSGU_SCRATCH_PAD_1); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("TIMEOUT : ToggleVal 0x%x," + "MSGU_SCRATCH_PAD1 = 0x%x\n", + toggleVal, regVal)); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("SCRATCH_PAD0 value = 0x%x\n", + pm8001_cr32(pm8001_ha, 0, + MSGU_SCRATCH_PAD_0))); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("SCRATCH_PAD2 value = 0x%x\n", + pm8001_cr32(pm8001_ha, 0, + MSGU_SCRATCH_PAD_2))); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("SCRATCH_PAD3 value = 0x%x\n", + pm8001_cr32(pm8001_ha, 0, + MSGU_SCRATCH_PAD_3))); + return -1; + } + + /* step 16 (Normal) - Clear ODMR and ODCR */ + pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL); + pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL); + + /* step 17 (Normal Mode): wait for the FW and IOP to get + ready - 1 sec timeout */ + /* Wait for the SPC Configuration Table to be ready */ + if (check_fw_ready(pm8001_ha) == -1) { + regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_1); + /* return error if MPI Configuration Table not ready */ + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("FW not ready SCRATCH_PAD1" + " = 0x%x\n", regVal)); + regVal = pm8001_cr32(pm8001_ha, 0, MSGU_SCRATCH_PAD_2); + /* return error if MPI Configuration Table not ready */ + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("FW not ready SCRATCH_PAD2" + " = 0x%x\n", regVal)); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("SCRATCH_PAD0 value = 0x%x\n", + pm8001_cr32(pm8001_ha, 0, + MSGU_SCRATCH_PAD_0))); + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("SCRATCH_PAD3 value = 0x%x\n", + pm8001_cr32(pm8001_ha, 0, + MSGU_SCRATCH_PAD_3))); + return -1; + } + } + + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("SPC soft reset Complete\n")); + return 0; +} + +static void pm8001_hw_chip_rst(struct pm8001_hba_info *pm8001_ha) +{ + u32 i; + u32 regVal; + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("chip reset start\n")); + + /* do SPC chip reset. */ + regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET); + regVal &= ~(SPC_REG_RESET_DEVICE); + pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal); + + /* delay 10 usec */ + udelay(10); + + /* bring chip reset out of reset */ + regVal = pm8001_cr32(pm8001_ha, 1, SPC_REG_RESET); + regVal |= SPC_REG_RESET_DEVICE; + pm8001_cw32(pm8001_ha, 1, SPC_REG_RESET, regVal); + + /* delay 10 usec */ + udelay(10); + + /* wait for 20 msec until the firmware gets reloaded */ + i = 20; + do { + mdelay(1); + } while ((--i) != 0); + + PM8001_INIT_DBG(pm8001_ha, + pm8001_printk("chip reset finished\n")); +} + +/** + * pm8001_chip_iounmap - which maped when initilized. + * @pm8001_ha: our hba card information + */ +static void pm8001_chip_iounmap(struct pm8001_hba_info *pm8001_ha) +{ + s8 bar, logical = 0; + for (bar = 0; bar < 6; bar++) { + /* + ** logical BARs for SPC: + ** bar 0 and 1 - logical BAR0 + ** bar 2 and 3 - logical BAR1 + ** bar4 - logical BAR2 + ** bar5 - logical BAR3 + ** Skip the appropriate assignments: + */ + if ((bar == 1) || (bar == 3)) + continue; + if (pm8001_ha->io_mem[logical].memvirtaddr) { + iounmap(pm8001_ha->io_mem[logical].memvirtaddr); + logical++; + } + } +} + +/** + * pm8001_chip_interrupt_enable - enable PM8001 chip interrupt + * @pm8001_ha: our hba card information + */ +static void +pm8001_chip_intx_interrupt_enable(struct pm8001_hba_info *pm8001_ha) +{ + pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_CLEAR_ALL); + pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, ODCR_CLEAR_ALL); +} + + /** + * pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt + * @pm8001_ha: our hba card information + */ +static void +pm8001_chip_intx_interrupt_disable(struct pm8001_hba_info *pm8001_ha) +{ + pm8001_cw32(pm8001_ha, 0, MSGU_ODMR, ODMR_MASK_ALL); +} + +/** + * pm8001_chip_msix_interrupt_enable - enable PM8001 chip interrupt + * @pm8001_ha: our hba card information + */ +static void +pm8001_chip_msix_interrupt_enable(struct pm8001_hba_info *pm8001_ha, + u32 int_vec_idx) +{ + u32 msi_index; + u32 value; + msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE; + msi_index += MSIX_TABLE_BASE; + pm8001_cw32(pm8001_ha, 0, msi_index, MSIX_INTERRUPT_ENABLE); + value = (1 << int_vec_idx); + pm8001_cw32(pm8001_ha, 0, MSGU_ODCR, value); + +} + +/** + * pm8001_chip_msix_interrupt_disable - disable PM8001 chip interrupt + * @pm8001_ha: our hba card information + */ +static void +pm8001_chip_msix_interrupt_disable(struct pm8001_hba_info *pm8001_ha, + u32 int_vec_idx) +{ + u32 msi_index; + msi_index = int_vec_idx * MSIX_TABLE_ELEMENT_SIZE; + msi_index += MSIX_TABLE_BASE; + pm8001_cw32(pm8001_ha, 0, msi_index, MSIX_INTERRUPT_DISABLE); + +} +/** + * pm8001_chip_interrupt_enable - enable PM8001 chip interrupt + * @pm8001_ha: our hba card information + */ +static void +pm8001_chip_interrupt_enable(struct pm8001_hba_info *pm8001_ha) +{ +#ifdef PM8001_USE_MSIX + pm8001_chip_msix_interrupt_enable(pm8001_ha, 0); + return; +#endif + pm8001_chip_intx_interrupt_enable(pm8001_ha); + +} + +/** + * pm8001_chip_intx_interrupt_disable- disable PM8001 chip interrupt + * @pm8001_ha: our hba card information + */ +static void +pm8001_chip_interrupt_disable(struct pm8001_hba_info *pm8001_ha) +{ +#ifdef PM8001_USE_MSIX + pm8001_chip_msix_interrupt_disable(pm8001_ha, 0); + return; +#endif + pm8001_chip_intx_interrupt_disable(pm8001_ha); + +} + +/** + * mpi_msg_free_get- get the free message buffer for transfer inbound queue. + * @circularQ: the inbound queue we want to transfer to HBA. + * @messageSize: the message size of this transfer, normally it is 64 bytes + * @messagePtr: the pointer to message. + */ +static u32 mpi_msg_free_get(struct inbound_queue_table *circularQ, + u16 messageSize, void **messagePtr) +{ + u32 offset, consumer_index; + struct mpi_msg_hdr *msgHeader; + u8 bcCount = 1; /* only support single buffer */ + + /* Checks is the requested message size can be allocated in this queue*/ + if (messageSize > 64) { + *messagePtr = NULL; + return -1; + } + + /* Stores the new consumer index */ + consumer_index = pm8001_read_32(circularQ->ci_virt); + circularQ->consumer_index = cpu_to_le32(consumer_index); + if (((circularQ->producer_idx + bcCount) % 256) == + circularQ->consumer_index) { + *messagePtr = NULL; + return -1; + } + /* get memory IOMB buffer address */ + offset = circularQ->producer_idx * 64; + /* increment to next bcCount element */ + circularQ->producer_idx = (circularQ->producer_idx + bcCount) % 256; + /* Adds that distance to the base of the region virtual address plus + the message header size*/ + msgHeader = (struct mpi_msg_hdr *)(circularQ->base_virt + offset); + *messagePtr = ((void *)msgHeader) + sizeof(struct mpi_msg_hdr); + return 0; +} + +/** + * mpi_build_cmd- build the message queue for transfer, update the PI to FW + * to tell the fw to get this message from IOMB. + * @pm8001_ha: our hba card information + * @circularQ: the inbound queue we want to transfer to HBA. + * @opCode: the operation code represents commands which LLDD and fw recognized. + * @payload: the command payload of each operation command. + */ +static u32 mpi_build_cmd(struct pm8001_hba_info *pm8001_ha, + struct inbound_queue_table *circularQ, + u32 opCode, void *payload) +{ + u32 Header = 0, hpriority = 0, bc = 1, category = 0x02; + u32 responseQueue = 0; + void *pMessage; + + if (mpi_msg_free_get(circularQ, 64, &pMessage) < 0) { + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("No free mpi buffer \n")); + return -1; + } + + /*Copy to the payload*/ + memcpy(pMessage, payload, (64 - sizeof(struct mpi_msg_hdr))); + + /*Build the header*/ + Header = ((1 << 31) | (hpriority << 30) | ((bc & 0x1f) << 24) + | ((responseQueue & 0x3F) << 16) + | ((category & 0xF) << 12) | (opCode & 0xFFF)); + + pm8001_write_32((pMessage - 4), 0, cpu_to_le32(Header)); + /*Update the PI to the firmware*/ + pm8001_cw32(pm8001_ha, circularQ->pi_pci_bar, + circularQ->pi_offset, circularQ->producer_idx); + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("after PI= %d CI= %d \n", circularQ->producer_idx, + circularQ->consumer_index)); + return 0; +} + +static u32 mpi_msg_free_set(struct pm8001_hba_info *pm8001_ha, + struct outbound_queue_table *circularQ, u8 bc) +{ + u32 producer_index; + /* free the circular queue buffer elements associated with the message*/ + circularQ->consumer_idx = (circularQ->consumer_idx + bc) % 256; + /* update the CI of outbound queue */ + pm8001_cw32(pm8001_ha, circularQ->ci_pci_bar, circularQ->ci_offset, + circularQ->consumer_idx); + /* Update the producer index from SPC*/ + producer_index = pm8001_read_32(circularQ->pi_virt); + circularQ->producer_index = cpu_to_le32(producer_index); + PM8001_IO_DBG(pm8001_ha, + pm8001_printk(" CI=%d PI=%d\n", circularQ->consumer_idx, + circularQ->producer_index)); + return 0; +} + +/** + * mpi_msg_consume- get the MPI message from outbound queue message table. + * @pm8001_ha: our hba card information + * @circularQ: the outbound queue table. + * @messagePtr1: the message contents of this outbound message. + * @pBC: the message size. + */ +static u32 mpi_msg_consume(struct pm8001_hba_info *pm8001_ha, + struct outbound_queue_table *circularQ, + void **messagePtr1, u8 *pBC) +{ + struct mpi_msg_hdr *msgHeader; + __le32 msgHeader_tmp; + u32 header_tmp; + do { + /* If there are not-yet-delivered messages ... */ + if (circularQ->producer_index != circularQ->consumer_idx) { + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("process an IOMB\n")); + /*Get the pointer to the circular queue buffer element*/ + msgHeader = (struct mpi_msg_hdr *) + (circularQ->base_virt + + circularQ->consumer_idx * 64); + /* read header */ + header_tmp = pm8001_read_32(msgHeader); + msgHeader_tmp = cpu_to_le32(header_tmp); + if (0 != (msgHeader_tmp & 0x80000000)) { + if (OPC_OUB_SKIP_ENTRY != + (msgHeader_tmp & 0xfff)) { + *messagePtr1 = + ((u8 *)msgHeader) + + sizeof(struct mpi_msg_hdr); + *pBC = (u8)((msgHeader_tmp >> 24) & + 0x1f); + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("mpi_msg_consume" + ": CI=%d PI=%d msgHeader=%x\n", + circularQ->consumer_idx, + circularQ->producer_index, + msgHeader_tmp)); + return MPI_IO_STATUS_SUCCESS; + } else { + u32 producer_index; + void *pi_virt = circularQ->pi_virt; + /* free the circular queue buffer + elements associated with the message*/ + circularQ->consumer_idx = + (circularQ->consumer_idx + + ((msgHeader_tmp >> 24) & 0x1f)) + % 256; + /* update the CI of outbound queue */ + pm8001_cw32(pm8001_ha, + circularQ->ci_pci_bar, + circularQ->ci_offset, + circularQ->consumer_idx); + /* Update the producer index from SPC */ + producer_index = + pm8001_read_32(pi_virt); + circularQ->producer_index = + cpu_to_le32(producer_index); + } + } else + return MPI_IO_STATUS_FAIL; + } + } while (circularQ->producer_index != circularQ->consumer_idx); + /* while we don't have any more not-yet-delivered message */ + /* report empty */ + return MPI_IO_STATUS_BUSY; +} + +static void pm8001_work_queue(struct work_struct *work) +{ + struct delayed_work *dw = container_of(work, struct delayed_work, work); + struct pm8001_wq *wq = container_of(dw, struct pm8001_wq, work_q); + struct pm8001_device *pm8001_dev; + struct domain_device *dev; + + switch (wq->handler) { + case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS: + pm8001_dev = wq->data; + dev = pm8001_dev->sas_device; + pm8001_I_T_nexus_reset(dev); + break; + case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY: + pm8001_dev = wq->data; + dev = pm8001_dev->sas_device; + pm8001_I_T_nexus_reset(dev); + break; + case IO_DS_IN_ERROR: + pm8001_dev = wq->data; + dev = pm8001_dev->sas_device; + pm8001_I_T_nexus_reset(dev); + break; + case IO_DS_NON_OPERATIONAL: + pm8001_dev = wq->data; + dev = pm8001_dev->sas_device; + pm8001_I_T_nexus_reset(dev); + break; + } + list_del(&wq->entry); + kfree(wq); +} + +static int pm8001_handle_event(struct pm8001_hba_info *pm8001_ha, void *data, + int handler) +{ + struct pm8001_wq *wq; + int ret = 0; + + wq = kmalloc(sizeof(struct pm8001_wq), GFP_ATOMIC); + if (wq) { + wq->pm8001_ha = pm8001_ha; + wq->data = data; + wq->handler = handler; + INIT_DELAYED_WORK(&wq->work_q, pm8001_work_queue); + list_add_tail(&wq->entry, &pm8001_ha->wq_list); + schedule_delayed_work(&wq->work_q, 0); + } else + ret = -ENOMEM; + + return ret; +} + +/** + * mpi_ssp_completion- process the event that FW response to the SSP request. + * @pm8001_ha: our hba card information + * @piomb: the message contents of this outbound message. + * + * When FW has completed a ssp request for example a IO request, after it has + * filled the SG data with the data, it will trigger this event represent + * that he has finished the job,please check the coresponding buffer. + * So we will tell the caller who maybe waiting the result to tell upper layer + * that the task has been finished. + */ +static int +mpi_ssp_completion(struct pm8001_hba_info *pm8001_ha , void *piomb) +{ + struct sas_task *t; + struct pm8001_ccb_info *ccb; + unsigned long flags; + u32 status; + u32 param; + u32 tag; + struct ssp_completion_resp *psspPayload; + struct task_status_struct *ts; + struct ssp_response_iu *iu; + struct pm8001_device *pm8001_dev; + psspPayload = (struct ssp_completion_resp *)(piomb + 4); + status = le32_to_cpu(psspPayload->status); + tag = le32_to_cpu(psspPayload->tag); + ccb = &pm8001_ha->ccb_info[tag]; + pm8001_dev = ccb->device; + param = le32_to_cpu(psspPayload->param); + + PM8001_IO_DBG(pm8001_ha, pm8001_printk("OPC_OUB_SSP_COMP\n")); + t = ccb->task; + + if (status) + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("sas IO status 0x%x\n", status)); + if (unlikely(!t || !t->lldd_task || !t->dev)) + return -1; + ts = &t->task_status; + switch (status) { + case IO_SUCCESS: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS" + ",param = %d \n", param)); + if (param == 0) { + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAM_GOOD; + } else { + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_PROTO_RESPONSE; + ts->residual = param; + iu = &psspPayload->ssp_resp_iu; + sas_ssp_task_response(pm8001_ha->dev, t, iu); + } + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_ABORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_ABORTED IOMB Tag \n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_ABORTED_TASK; + break; + case IO_UNDERFLOW: + /* SSP Completion with error */ + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW" + ",param = %d \n", param)); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_UNDERRUN; + ts->residual = param; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_NO_DEVICE: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_NO_DEVICE\n")); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_PHY_DOWN; + break; + case IO_XFER_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_XFER_ERROR_PHY_NOT_READY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_EPROTO; + break; + case IO_OPEN_CNX_ERROR_ZONE_VIOLATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + break; + case IO_OPEN_CNX_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_CONT0; + break; + case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + if (!t->uldd_task) + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS); + break; + case IO_OPEN_CNX_ERROR_BAD_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_BAD_DEST; + break; + case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_" + "NOT_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_CONN_RATE; + break; + case IO_OPEN_CNX_ERROR_WRONG_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_WRONG_DEST; + break; + case IO_XFER_ERROR_NAK_RECEIVED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_XFER_ERROR_ACK_NAK_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_NAK_R_ERR; + break; + case IO_XFER_ERROR_DMA: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_DMA\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_XFER_OPEN_RETRY_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_XFER_ERROR_OFFSET_MISMATCH: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_PORT_IN_RESET: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_PORT_IN_RESET\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_DS_NON_OPERATIONAL: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_DS_NON_OPERATIONAL\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + if (!t->uldd_task) + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_DS_NON_OPERATIONAL); + break; + case IO_DS_IN_RECOVERY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_DS_IN_RECOVERY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_TM_TAG_NOT_FOUND: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_TM_TAG_NOT_FOUND\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_SSP_EXT_IU_ZERO_LEN_ERROR: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_SSP_EXT_IU_ZERO_LEN_ERROR\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + default: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("Unknown status 0x%x\n", status)); + /* not allowed case. Therefore, return failed status */ + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + } + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("scsi_satus = %x \n ", + psspPayload->ssp_resp_iu.status)); + spin_lock_irqsave(&t->task_state_lock, flags); + t->task_state_flags &= ~SAS_TASK_STATE_PENDING; + t->task_state_flags &= ~SAS_TASK_AT_INITIATOR; + t->task_state_flags |= SAS_TASK_STATE_DONE; + if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) { + spin_unlock_irqrestore(&t->task_state_lock, flags); + PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with" + " io_status 0x%x resp 0x%x " + "stat 0x%x but aborted by upper layer!\n", + t, status, ts->resp, ts->stat)); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + } else { + spin_unlock_irqrestore(&t->task_state_lock, flags); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/* in order to force CPU ordering */ + t->task_done(t); + } + return 0; +} + +/*See the comments for mpi_ssp_completion */ +static int mpi_ssp_event(struct pm8001_hba_info *pm8001_ha , void *piomb) +{ + struct sas_task *t; + unsigned long flags; + struct task_status_struct *ts; + struct pm8001_ccb_info *ccb; + struct pm8001_device *pm8001_dev; + struct ssp_event_resp *psspPayload = + (struct ssp_event_resp *)(piomb + 4); + u32 event = le32_to_cpu(psspPayload->event); + u32 tag = le32_to_cpu(psspPayload->tag); + u32 port_id = le32_to_cpu(psspPayload->port_id); + u32 dev_id = le32_to_cpu(psspPayload->device_id); + + ccb = &pm8001_ha->ccb_info[tag]; + t = ccb->task; + pm8001_dev = ccb->device; + if (event) + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("sas IO status 0x%x\n", event)); + if (unlikely(!t || !t->lldd_task || !t->dev)) + return -1; + ts = &t->task_status; + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("port_id = %x,device_id = %x\n", + port_id, dev_id)); + switch (event) { + case IO_OVERFLOW: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n");) + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + ts->residual = 0; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_XFER_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_INTERRUPTED; + break; + case IO_XFER_ERROR_PHY_NOT_READY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT" + "_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_EPROTO; + break; + case IO_OPEN_CNX_ERROR_ZONE_VIOLATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + break; + case IO_OPEN_CNX_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_CONT0; + break; + case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + if (!t->uldd_task) + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS); + break; + case IO_OPEN_CNX_ERROR_BAD_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_BAD_DEST; + break; + case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_" + "NOT_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_CONN_RATE; + break; + case IO_OPEN_CNX_ERROR_WRONG_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_WRONG_DEST; + break; + case IO_XFER_ERROR_NAK_RECEIVED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + break; + case IO_XFER_ERROR_ACK_NAK_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_NAK_R_ERR; + break; + case IO_XFER_OPEN_RETRY_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_XFER_ERROR_UNEXPECTED_PHASE: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + break; + case IO_XFER_ERROR_XFER_RDY_OVERRUN: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + break; + case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + break; + case IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + break; + case IO_XFER_ERROR_OFFSET_MISMATCH: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + break; + case IO_XFER_ERROR_XFER_ZERO_DATA_LEN: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + break; + case IO_XFER_CMD_FRAME_ISSUED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk(" IO_XFER_CMD_FRAME_ISSUED\n")); + return 0; + default: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("Unknown status 0x%x\n", event)); + /* not allowed case. Therefore, return failed status */ + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + break; + } + spin_lock_irqsave(&t->task_state_lock, flags); + t->task_state_flags &= ~SAS_TASK_STATE_PENDING; + t->task_state_flags &= ~SAS_TASK_AT_INITIATOR; + t->task_state_flags |= SAS_TASK_STATE_DONE; + if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) { + spin_unlock_irqrestore(&t->task_state_lock, flags); + PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with" + " event 0x%x resp 0x%x " + "stat 0x%x but aborted by upper layer!\n", + t, event, ts->resp, ts->stat)); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + } else { + spin_unlock_irqrestore(&t->task_state_lock, flags); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/* in order to force CPU ordering */ + t->task_done(t); + } + return 0; +} + +/*See the comments for mpi_ssp_completion */ +static int +mpi_sata_completion(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct sas_task *t; + struct pm8001_ccb_info *ccb; + unsigned long flags; + u32 param; + u32 status; + u32 tag; + struct sata_completion_resp *psataPayload; + struct task_status_struct *ts; + struct ata_task_resp *resp ; + u32 *sata_resp; + struct pm8001_device *pm8001_dev; + + psataPayload = (struct sata_completion_resp *)(piomb + 4); + status = le32_to_cpu(psataPayload->status); + tag = le32_to_cpu(psataPayload->tag); + + ccb = &pm8001_ha->ccb_info[tag]; + param = le32_to_cpu(psataPayload->param); + t = ccb->task; + ts = &t->task_status; + pm8001_dev = ccb->device; + if (status) + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("sata IO status 0x%x\n", status)); + if (unlikely(!t || !t->lldd_task || !t->dev)) + return -1; + + switch (status) { + case IO_SUCCESS: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n")); + if (param == 0) { + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAM_GOOD; + } else { + u8 len; + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_PROTO_RESPONSE; + ts->residual = param; + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("SAS_PROTO_RESPONSE len = %d\n", + param)); + sata_resp = &psataPayload->sata_resp[0]; + resp = (struct ata_task_resp *)ts->buf; + if (t->ata_task.dma_xfer == 0 && + t->data_dir == PCI_DMA_FROMDEVICE) { + len = sizeof(struct pio_setup_fis); + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("PIO read len = %d\n", len)); + } else if (t->ata_task.use_ncq) { + len = sizeof(struct set_dev_bits_fis); + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("FPDMA len = %d\n", len)); + } else { + len = sizeof(struct dev_to_host_fis); + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("other len = %d\n", len)); + } + if (SAS_STATUS_BUF_SIZE >= sizeof(*resp)) { + resp->frame_len = len; + memcpy(&resp->ending_fis[0], sata_resp, len); + ts->buf_valid_size = sizeof(*resp); + } else + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("response to large \n")); + } + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_ABORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_ABORTED IOMB Tag \n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_ABORTED_TASK; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + /* following cases are to do cases */ + case IO_UNDERFLOW: + /* SATA Completion with error */ + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_UNDERFLOW param = %d\n", param)); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_UNDERRUN; + ts->residual = param; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_NO_DEVICE: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_NO_DEVICE\n")); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_PHY_DOWN; + break; + case IO_XFER_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_INTERRUPTED; + break; + case IO_XFER_ERROR_PHY_NOT_READY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT" + "_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_EPROTO; + break; + case IO_OPEN_CNX_ERROR_ZONE_VIOLATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + break; + case IO_OPEN_CNX_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_CONT0; + break; + case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + if (!t->uldd_task) { + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_QUEUE_FULL; + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/*in order to force CPU ordering*/ + t->task_done(t); + return 0; + } + break; + case IO_OPEN_CNX_ERROR_BAD_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_BAD_DEST; + if (!t->uldd_task) { + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_QUEUE_FULL; + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/*ditto*/ + t->task_done(t); + return 0; + } + break; + case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_" + "NOT_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_CONN_RATE; + break; + case IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_STP_RESOURCES" + "_BUSY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + if (!t->uldd_task) { + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_QUEUE_FULL; + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/* ditto*/ + t->task_done(t); + return 0; + } + break; + case IO_OPEN_CNX_ERROR_WRONG_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_WRONG_DEST; + break; + case IO_XFER_ERROR_NAK_RECEIVED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_NAK_R_ERR; + break; + case IO_XFER_ERROR_ACK_NAK_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_ACK_NAK_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_NAK_R_ERR; + break; + case IO_XFER_ERROR_DMA: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_DMA\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_ABORTED_TASK; + break; + case IO_XFER_ERROR_SATA_LINK_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_SATA_LINK_TIMEOUT\n")); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_DEV_NO_RESPONSE; + break; + case IO_XFER_ERROR_REJECTED_NCQ_MODE: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_UNDERRUN; + break; + case IO_XFER_OPEN_RETRY_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + case IO_PORT_IN_RESET: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_PORT_IN_RESET\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + break; + case IO_DS_NON_OPERATIONAL: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_DS_NON_OPERATIONAL\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + if (!t->uldd_task) { + pm8001_handle_event(pm8001_ha, pm8001_dev, + IO_DS_NON_OPERATIONAL); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_QUEUE_FULL; + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/*ditto*/ + t->task_done(t); + return 0; + } + break; + case IO_DS_IN_RECOVERY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk(" IO_DS_IN_RECOVERY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + break; + case IO_DS_IN_ERROR: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_DS_IN_ERROR\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + if (!t->uldd_task) { + pm8001_handle_event(pm8001_ha, pm8001_dev, + IO_DS_IN_ERROR); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_QUEUE_FULL; + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/*ditto*/ + t->task_done(t); + return 0; + } + break; + case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + default: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("Unknown status 0x%x\n", status)); + /* not allowed case. Therefore, return failed status */ + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + break; + } + spin_lock_irqsave(&t->task_state_lock, flags); + t->task_state_flags &= ~SAS_TASK_STATE_PENDING; + t->task_state_flags &= ~SAS_TASK_AT_INITIATOR; + t->task_state_flags |= SAS_TASK_STATE_DONE; + if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) { + spin_unlock_irqrestore(&t->task_state_lock, flags); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("task 0x%p done with io_status 0x%x" + " resp 0x%x stat 0x%x but aborted by upper layer!\n", + t, status, ts->resp, ts->stat)); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + } else { + spin_unlock_irqrestore(&t->task_state_lock, flags); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/* ditto */ + t->task_done(t); + } + return 0; +} + +/*See the comments for mpi_ssp_completion */ +static int mpi_sata_event(struct pm8001_hba_info *pm8001_ha , void *piomb) +{ + struct sas_task *t; + unsigned long flags; + struct task_status_struct *ts; + struct pm8001_ccb_info *ccb; + struct pm8001_device *pm8001_dev; + struct sata_event_resp *psataPayload = + (struct sata_event_resp *)(piomb + 4); + u32 event = le32_to_cpu(psataPayload->event); + u32 tag = le32_to_cpu(psataPayload->tag); + u32 port_id = le32_to_cpu(psataPayload->port_id); + u32 dev_id = le32_to_cpu(psataPayload->device_id); + + ccb = &pm8001_ha->ccb_info[tag]; + t = ccb->task; + pm8001_dev = ccb->device; + if (event) + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("sata IO status 0x%x\n", event)); + if (unlikely(!t || !t->lldd_task || !t->dev)) + return -1; + ts = &t->task_status; + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("port_id = %x,device_id = %x\n", + port_id, dev_id)); + switch (event) { + case IO_OVERFLOW: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + ts->residual = 0; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_XFER_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_INTERRUPTED; + break; + case IO_XFER_ERROR_PHY_NOT_READY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT" + "_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_EPROTO; + break; + case IO_OPEN_CNX_ERROR_ZONE_VIOLATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + break; + case IO_OPEN_CNX_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_CONT0; + break; + case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_DEV_NO_RESPONSE; + if (!t->uldd_task) { + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_QUEUE_FULL; + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/*ditto*/ + t->task_done(t); + return 0; + } + break; + case IO_OPEN_CNX_ERROR_BAD_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); + ts->resp = SAS_TASK_UNDELIVERED; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_BAD_DEST; + break; + case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_" + "NOT_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_CONN_RATE; + break; + case IO_OPEN_CNX_ERROR_WRONG_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_WRONG_DEST; + break; + case IO_XFER_ERROR_NAK_RECEIVED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_NAK_RECEIVED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_NAK_R_ERR; + break; + case IO_XFER_ERROR_PEER_ABORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_PEER_ABORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_NAK_R_ERR; + break; + case IO_XFER_ERROR_REJECTED_NCQ_MODE: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_REJECTED_NCQ_MODE\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_UNDERRUN; + break; + case IO_XFER_OPEN_RETRY_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + case IO_XFER_ERROR_UNEXPECTED_PHASE: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_UNEXPECTED_PHASE\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + case IO_XFER_ERROR_XFER_RDY_OVERRUN: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_XFER_RDY_OVERRUN\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + case IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + case IO_XFER_ERROR_OFFSET_MISMATCH: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_OFFSET_MISMATCH\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + case IO_XFER_ERROR_XFER_ZERO_DATA_LEN: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_XFER_ZERO_DATA_LEN\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + case IO_XFER_CMD_FRAME_ISSUED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_CMD_FRAME_ISSUED\n")); + break; + case IO_XFER_PIO_SETUP_ERROR: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_PIO_SETUP_ERROR\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + default: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("Unknown status 0x%x\n", event)); + /* not allowed case. Therefore, return failed status */ + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_TO; + break; + } + spin_lock_irqsave(&t->task_state_lock, flags); + t->task_state_flags &= ~SAS_TASK_STATE_PENDING; + t->task_state_flags &= ~SAS_TASK_AT_INITIATOR; + t->task_state_flags |= SAS_TASK_STATE_DONE; + if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) { + spin_unlock_irqrestore(&t->task_state_lock, flags); + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("task 0x%p done with io_status 0x%x" + " resp 0x%x stat 0x%x but aborted by upper layer!\n", + t, event, ts->resp, ts->stat)); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + } else { + spin_unlock_irqrestore(&t->task_state_lock, flags); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/* in order to force CPU ordering */ + t->task_done(t); + } + return 0; +} + +/*See the comments for mpi_ssp_completion */ +static int +mpi_smp_completion(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + u32 param; + struct sas_task *t; + struct pm8001_ccb_info *ccb; + unsigned long flags; + u32 status; + u32 tag; + struct smp_completion_resp *psmpPayload; + struct task_status_struct *ts; + struct pm8001_device *pm8001_dev; + + psmpPayload = (struct smp_completion_resp *)(piomb + 4); + status = le32_to_cpu(psmpPayload->status); + tag = le32_to_cpu(psmpPayload->tag); + + ccb = &pm8001_ha->ccb_info[tag]; + param = le32_to_cpu(psmpPayload->param); + t = ccb->task; + ts = &t->task_status; + pm8001_dev = ccb->device; + if (status) + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("smp IO status 0x%x\n", status)); + if (unlikely(!t || !t->lldd_task || !t->dev)) + return -1; + + switch (status) { + case IO_SUCCESS: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAM_GOOD; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_ABORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_ABORTED IOMB\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_ABORTED_TASK; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_OVERFLOW: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_UNDERFLOW\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DATA_OVERRUN; + ts->residual = 0; + if (pm8001_dev) + pm8001_dev->running_req--; + break; + case IO_NO_DEVICE: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_NO_DEVICE\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_PHY_DOWN; + break; + case IO_ERROR_HW_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_ERROR_HW_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAM_BUSY; + break; + case IO_XFER_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAM_BUSY; + break; + case IO_XFER_ERROR_PHY_NOT_READY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_PHY_NOT_READY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAM_BUSY; + break; + case IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + break; + case IO_OPEN_CNX_ERROR_ZONE_VIOLATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_ZONE_VIOLATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + break; + case IO_OPEN_CNX_ERROR_BREAK: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BREAK\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_CONT0; + break; + case IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_UNKNOWN; + pm8001_handle_event(pm8001_ha, + pm8001_dev, + IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS); + break; + case IO_OPEN_CNX_ERROR_BAD_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_BAD_DESTINATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_BAD_DEST; + break; + case IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_CONNECTION_RATE_" + "NOT_SUPPORTED\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_CONN_RATE; + break; + case IO_OPEN_CNX_ERROR_WRONG_DESTINATION: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_WRONG_DESTINATION\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_WRONG_DEST; + break; + case IO_XFER_ERROR_RX_FRAME: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_ERROR_RX_FRAME\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + break; + case IO_XFER_OPEN_RETRY_TIMEOUT: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_XFER_OPEN_RETRY_TIMEOUT\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_ERROR_INTERNAL_SMP_RESOURCE: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_ERROR_INTERNAL_SMP_RESOURCE\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_QUEUE_FULL; + break; + case IO_PORT_IN_RESET: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_PORT_IN_RESET\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_DS_NON_OPERATIONAL: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_DS_NON_OPERATIONAL\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + break; + case IO_DS_IN_RECOVERY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_DS_IN_RECOVERY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + case IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_OPEN_REJECT; + ts->open_rej_reason = SAS_OREJ_RSVD_RETRY; + break; + default: + PM8001_IO_DBG(pm8001_ha, + pm8001_printk("Unknown status 0x%x\n", status)); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAS_DEV_NO_RESPONSE; + /* not allowed case. Therefore, return failed status */ + break; + } + spin_lock_irqsave(&t->task_state_lock, flags); + t->task_state_flags &= ~SAS_TASK_STATE_PENDING; + t->task_state_flags &= ~SAS_TASK_AT_INITIATOR; + t->task_state_flags |= SAS_TASK_STATE_DONE; + if (unlikely((t->task_state_flags & SAS_TASK_STATE_ABORTED))) { + spin_unlock_irqrestore(&t->task_state_lock, flags); + PM8001_FAIL_DBG(pm8001_ha, pm8001_printk("task 0x%p done with" + " io_status 0x%x resp 0x%x " + "stat 0x%x but aborted by upper layer!\n", + t, status, ts->resp, ts->stat)); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + } else { + spin_unlock_irqrestore(&t->task_state_lock, flags); + pm8001_ccb_task_free(pm8001_ha, t, ccb, tag); + mb();/* in order to force CPU ordering */ + t->task_done(t); + } + return 0; +} + +static void +mpi_set_dev_state_resp(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct set_dev_state_resp *pPayload = + (struct set_dev_state_resp *)(piomb + 4); + u32 tag = le32_to_cpu(pPayload->tag); + struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag]; + struct pm8001_device *pm8001_dev = ccb->device; + u32 status = le32_to_cpu(pPayload->status); + u32 device_id = le32_to_cpu(pPayload->device_id); + u8 pds = le32_to_cpu(pPayload->pds_nds) | PDS_BITS; + u8 nds = le32_to_cpu(pPayload->pds_nds) | NDS_BITS; + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Set device id = 0x%x state " + "from 0x%x to 0x%x status = 0x%x!\n", + device_id, pds, nds, status)); + complete(pm8001_dev->setds_completion); + ccb->task = NULL; + ccb->ccb_tag = 0xFFFFFFFF; + pm8001_ccb_free(pm8001_ha, tag); +} + +static void +mpi_set_nvmd_resp(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct get_nvm_data_resp *pPayload = + (struct get_nvm_data_resp *)(piomb + 4); + u32 tag = le32_to_cpu(pPayload->tag); + struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag]; + u32 dlen_status = le32_to_cpu(pPayload->dlen_status); + complete(pm8001_ha->nvmd_completion); + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Set nvm data complete!\n")); + if ((dlen_status & NVMD_STAT) != 0) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Set nvm data error!\n")); + return; + } + ccb->task = NULL; + ccb->ccb_tag = 0xFFFFFFFF; + pm8001_ccb_free(pm8001_ha, tag); +} + +static void +mpi_get_nvmd_resp(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct fw_control_ex *fw_control_context; + struct get_nvm_data_resp *pPayload = + (struct get_nvm_data_resp *)(piomb + 4); + u32 tag = le32_to_cpu(pPayload->tag); + struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag]; + u32 dlen_status = le32_to_cpu(pPayload->dlen_status); + u32 ir_tds_bn_dps_das_nvm = + le32_to_cpu(pPayload->ir_tda_bn_dps_das_nvm); + void *virt_addr = pm8001_ha->memoryMap.region[NVMD].virt_ptr; + fw_control_context = ccb->fw_control_context; + + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("Get nvm data complete!\n")); + if ((dlen_status & NVMD_STAT) != 0) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Get nvm data error!\n")); + complete(pm8001_ha->nvmd_completion); + return; + } + + if (ir_tds_bn_dps_das_nvm & IPMode) { + /* indirect mode - IR bit set */ + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("Get NVMD success, IR=1\n")); + if ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == TWI_DEVICE) { + if (ir_tds_bn_dps_das_nvm == 0x80a80200) { + memcpy(pm8001_ha->sas_addr, + ((u8 *)virt_addr + 4), + SAS_ADDR_SIZE); + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("Get SAS address" + " from VPD successfully!\n")); + } + } else if (((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == C_SEEPROM) + || ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == VPD_FLASH) || + ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == EXPAN_ROM)) { + ; + } else if (((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == AAP1_RDUMP) + || ((ir_tds_bn_dps_das_nvm & NVMD_TYPE) == IOP_RDUMP)) { + ; + } else { + /* Should not be happened*/ + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("(IR=1)Wrong Device type 0x%x\n", + ir_tds_bn_dps_das_nvm)); + } + } else /* direct mode */{ + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("Get NVMD success, IR=0, dataLen=%d\n", + (dlen_status & NVMD_LEN) >> 24)); + } + memcpy((void *)(fw_control_context->usrAddr), + (void *)(pm8001_ha->memoryMap.region[NVMD].virt_ptr), + fw_control_context->len); + complete(pm8001_ha->nvmd_completion); + ccb->task = NULL; + ccb->ccb_tag = 0xFFFFFFFF; + pm8001_ccb_free(pm8001_ha, tag); +} + +static int mpi_local_phy_ctl(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct local_phy_ctl_resp *pPayload = + (struct local_phy_ctl_resp *)(piomb + 4); + u32 status = le32_to_cpu(pPayload->status); + u32 phy_id = le32_to_cpu(pPayload->phyop_phyid) & ID_BITS; + u32 phy_op = le32_to_cpu(pPayload->phyop_phyid) & OP_BITS; + if (status != 0) { + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("%x phy execute %x phy op failed! \n", + phy_id, phy_op)); + } else + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("%x phy execute %x phy op success! \n", + phy_id, phy_op)); + return 0; +} + +/** + * pm8001_bytes_dmaed - one of the interface function communication with libsas + * @pm8001_ha: our hba card information + * @i: which phy that received the event. + * + * when HBA driver received the identify done event or initiate FIS received + * event(for SATA), it will invoke this function to notify the sas layer that + * the sas toplogy has formed, please discover the the whole sas domain, + * while receive a broadcast(change) primitive just tell the sas + * layer to discover the changed domain rather than the whole domain. + */ +static void pm8001_bytes_dmaed(struct pm8001_hba_info *pm8001_ha, int i) +{ + struct pm8001_phy *phy = &pm8001_ha->phy[i]; + struct asd_sas_phy *sas_phy = &phy->sas_phy; + struct sas_ha_struct *sas_ha; + if (!phy->phy_attached) + return; + + sas_ha = pm8001_ha->sas; + if (sas_phy->phy) { + struct sas_phy *sphy = sas_phy->phy; + sphy->negotiated_linkrate = sas_phy->linkrate; + sphy->minimum_linkrate = phy->minimum_linkrate; + sphy->minimum_linkrate_hw = SAS_LINK_RATE_1_5_GBPS; + sphy->maximum_linkrate = phy->maximum_linkrate; + sphy->maximum_linkrate_hw = phy->maximum_linkrate; + } + + if (phy->phy_type & PORT_TYPE_SAS) { + struct sas_identify_frame *id; + id = (struct sas_identify_frame *)phy->frame_rcvd; + id->dev_type = phy->identify.device_type; + id->initiator_bits = SAS_PROTOCOL_ALL; + id->target_bits = phy->identify.target_port_protocols; + } else if (phy->phy_type & PORT_TYPE_SATA) { + /*Nothing*/ + } + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("phy %d byte dmaded.\n", i)); + + sas_phy->frame_rcvd_size = phy->frame_rcvd_size; + pm8001_ha->sas->notify_port_event(sas_phy, PORTE_BYTES_DMAED); +} + +/* Get the link rate speed */ +static void get_lrate_mode(struct pm8001_phy *phy, u8 link_rate) +{ + struct sas_phy *sas_phy = phy->sas_phy.phy; + + switch (link_rate) { + case PHY_SPEED_60: + phy->sas_phy.linkrate = SAS_LINK_RATE_6_0_GBPS; + phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_6_0_GBPS; + break; + case PHY_SPEED_30: + phy->sas_phy.linkrate = SAS_LINK_RATE_3_0_GBPS; + phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_3_0_GBPS; + break; + case PHY_SPEED_15: + phy->sas_phy.linkrate = SAS_LINK_RATE_1_5_GBPS; + phy->sas_phy.phy->negotiated_linkrate = SAS_LINK_RATE_1_5_GBPS; + break; + } + sas_phy->negotiated_linkrate = phy->sas_phy.linkrate; + sas_phy->maximum_linkrate_hw = SAS_LINK_RATE_6_0_GBPS; + sas_phy->minimum_linkrate_hw = SAS_LINK_RATE_1_5_GBPS; + sas_phy->maximum_linkrate = SAS_LINK_RATE_6_0_GBPS; + sas_phy->minimum_linkrate = SAS_LINK_RATE_1_5_GBPS; +} + +/** + * asd_get_attached_sas_addr -- extract/generate attached SAS address + * @phy: pointer to asd_phy + * @sas_addr: pointer to buffer where the SAS address is to be written + * + * This function extracts the SAS address from an IDENTIFY frame + * received. If OOB is SATA, then a SAS address is generated from the + * HA tables. + * + * LOCKING: the frame_rcvd_lock needs to be held since this parses the frame + * buffer. + */ +static void pm8001_get_attached_sas_addr(struct pm8001_phy *phy, + u8 *sas_addr) +{ + if (phy->sas_phy.frame_rcvd[0] == 0x34 + && phy->sas_phy.oob_mode == SATA_OOB_MODE) { + struct pm8001_hba_info *pm8001_ha = phy->sas_phy.ha->lldd_ha; + /* FIS device-to-host */ + u64 addr = be64_to_cpu(*(__be64 *)pm8001_ha->sas_addr); + addr += phy->sas_phy.id; + *(__be64 *)sas_addr = cpu_to_be64(addr); + } else { + struct sas_identify_frame *idframe = + (void *) phy->sas_phy.frame_rcvd; + memcpy(sas_addr, idframe->sas_addr, SAS_ADDR_SIZE); + } +} + +/** + * pm8001_hw_event_ack_req- For PM8001,some events need to acknowage to FW. + * @pm8001_ha: our hba card information + * @Qnum: the outbound queue message number. + * @SEA: source of event to ack + * @port_id: port id. + * @phyId: phy id. + * @param0: parameter 0. + * @param1: parameter 1. + */ +static void pm8001_hw_event_ack_req(struct pm8001_hba_info *pm8001_ha, + u32 Qnum, u32 SEA, u32 port_id, u32 phyId, u32 param0, u32 param1) +{ + struct hw_event_ack_req payload; + u32 opc = OPC_INB_SAS_HW_EVENT_ACK; + + struct inbound_queue_table *circularQ; + + memset((u8 *)&payload, 0, sizeof(payload)); + circularQ = &pm8001_ha->inbnd_q_tbl[Qnum]; + payload.tag = 1; + payload.sea_phyid_portid = cpu_to_le32(((SEA & 0xFFFF) << 8) | + ((phyId & 0x0F) << 4) | (port_id & 0x0F)); + payload.param0 = cpu_to_le32(param0); + payload.param1 = cpu_to_le32(param1); + mpi_build_cmd(pm8001_ha, circularQ, opc, &payload); +} + +static int pm8001_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha, + u32 phyId, u32 phy_op); + +/** + * hw_event_sas_phy_up -FW tells me a SAS phy up event. + * @pm8001_ha: our hba card information + * @piomb: IO message buffer + */ +static void +hw_event_sas_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct hw_event_resp *pPayload = + (struct hw_event_resp *)(piomb + 4); + u32 lr_evt_status_phyid_portid = + le32_to_cpu(pPayload->lr_evt_status_phyid_portid); + u8 link_rate = + (u8)((lr_evt_status_phyid_portid & 0xF0000000) >> 28); + u8 phy_id = + (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4); + struct sas_ha_struct *sas_ha = pm8001_ha->sas; + struct pm8001_phy *phy = &pm8001_ha->phy[phy_id]; + unsigned long flags; + u8 deviceType = pPayload->sas_identify.dev_type; + + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_SAS_PHY_UP \n")); + + switch (deviceType) { + case SAS_PHY_UNUSED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("device type no device.\n")); + break; + case SAS_END_DEVICE: + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("end device.\n")); + pm8001_chip_phy_ctl_req(pm8001_ha, phy_id, + PHY_NOTIFY_ENABLE_SPINUP); + get_lrate_mode(phy, link_rate); + break; + case SAS_EDGE_EXPANDER_DEVICE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("expander device.\n")); + get_lrate_mode(phy, link_rate); + break; + case SAS_FANOUT_EXPANDER_DEVICE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("fanout expander device.\n")); + get_lrate_mode(phy, link_rate); + break; + default: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("unkown device type(%x)\n", deviceType)); + break; + } + phy->phy_type |= PORT_TYPE_SAS; + phy->identify.device_type = deviceType; + phy->phy_attached = 1; + if (phy->identify.device_type == SAS_END_DEV) + phy->identify.target_port_protocols = SAS_PROTOCOL_SSP; + else if (phy->identify.device_type != NO_DEVICE) + phy->identify.target_port_protocols = SAS_PROTOCOL_SMP; + phy->sas_phy.oob_mode = SAS_OOB_MODE; + sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE); + spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags); + memcpy(phy->frame_rcvd, &pPayload->sas_identify, + sizeof(struct sas_identify_frame)-4); + phy->frame_rcvd_size = sizeof(struct sas_identify_frame) - 4; + pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr); + spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags); + if (pm8001_ha->flags == PM8001F_RUN_TIME) + mdelay(200);/*delay a moment to wait disk to spinup*/ + pm8001_bytes_dmaed(pm8001_ha, phy_id); +} + +/** + * hw_event_sata_phy_up -FW tells me a SATA phy up event. + * @pm8001_ha: our hba card information + * @piomb: IO message buffer + */ +static void +hw_event_sata_phy_up(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct hw_event_resp *pPayload = + (struct hw_event_resp *)(piomb + 4); + u32 lr_evt_status_phyid_portid = + le32_to_cpu(pPayload->lr_evt_status_phyid_portid); + u8 link_rate = + (u8)((lr_evt_status_phyid_portid & 0xF0000000) >> 28); + u8 phy_id = + (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4); + struct sas_ha_struct *sas_ha = pm8001_ha->sas; + struct pm8001_phy *phy = &pm8001_ha->phy[phy_id]; + unsigned long flags; + get_lrate_mode(phy, link_rate); + phy->phy_type |= PORT_TYPE_SATA; + phy->phy_attached = 1; + phy->sas_phy.oob_mode = SATA_OOB_MODE; + sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_DONE); + spin_lock_irqsave(&phy->sas_phy.frame_rcvd_lock, flags); + memcpy(phy->frame_rcvd, ((u8 *)&pPayload->sata_fis - 4), + sizeof(struct dev_to_host_fis)); + phy->frame_rcvd_size = sizeof(struct dev_to_host_fis); + phy->identify.target_port_protocols = SAS_PROTOCOL_SATA; + phy->identify.device_type = SATA_DEV; + pm8001_get_attached_sas_addr(phy, phy->sas_phy.attached_sas_addr); + spin_unlock_irqrestore(&phy->sas_phy.frame_rcvd_lock, flags); + pm8001_bytes_dmaed(pm8001_ha, phy_id); +} + +/** + * hw_event_phy_down -we should notify the libsas the phy is down. + * @pm8001_ha: our hba card information + * @piomb: IO message buffer + */ +static void +hw_event_phy_down(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct hw_event_resp *pPayload = + (struct hw_event_resp *)(piomb + 4); + u32 lr_evt_status_phyid_portid = + le32_to_cpu(pPayload->lr_evt_status_phyid_portid); + u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F); + u8 phy_id = + (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4); + u32 npip_portstate = le32_to_cpu(pPayload->npip_portstate); + u8 portstate = (u8)(npip_portstate & 0x0000000F); + + switch (portstate) { + case PORT_VALID: + break; + case PORT_INVALID: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" PortInvalid portID %d \n", port_id)); + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" Last phy Down and port invalid\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN, + port_id, phy_id, 0, 0); + break; + case PORT_IN_RESET: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" PortInReset portID %d \n", port_id)); + break; + case PORT_NOT_ESTABLISHED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" phy Down and PORT_NOT_ESTABLISHED\n")); + break; + case PORT_LOSTCOMM: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" phy Down and PORT_LOSTCOMM\n")); + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" Last phy Down and port invalid\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_PHY_DOWN, + port_id, phy_id, 0, 0); + break; + default: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" phy Down and(default) = %x\n", + portstate)); + break; + + } +} + +/** + * mpi_reg_resp -process register device ID response. + * @pm8001_ha: our hba card information + * @piomb: IO message buffer + * + * when sas layer find a device it will notify LLDD, then the driver register + * the domain device to FW, this event is the return device ID which the FW + * has assigned, from now,inter-communication with FW is no longer using the + * SAS address, use device ID which FW assigned. + */ +static int mpi_reg_resp(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + u32 status; + u32 device_id; + u32 htag; + struct pm8001_ccb_info *ccb; + struct pm8001_device *pm8001_dev; + struct dev_reg_resp *registerRespPayload = + (struct dev_reg_resp *)(piomb + 4); + + htag = le32_to_cpu(registerRespPayload->tag); + ccb = &pm8001_ha->ccb_info[registerRespPayload->tag]; + pm8001_dev = ccb->device; + status = le32_to_cpu(registerRespPayload->status); + device_id = le32_to_cpu(registerRespPayload->device_id); + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" register device is status = %d\n", status)); + switch (status) { + case DEVREG_SUCCESS: + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("DEVREG_SUCCESS\n")); + pm8001_dev->device_id = device_id; + break; + case DEVREG_FAILURE_OUT_OF_RESOURCE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_OUT_OF_RESOURCE\n")); + break; + case DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED\n")); + break; + case DEVREG_FAILURE_INVALID_PHY_ID: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_INVALID_PHY_ID\n")); + break; + case DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED\n")); + break; + case DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE\n")); + break; + case DEVREG_FAILURE_PORT_NOT_VALID_STATE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_PORT_NOT_VALID_STATE\n")); + break; + case DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID\n")); + break; + default: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("DEVREG_FAILURE_DEVICE_TYPE_NOT_UNSORPORTED\n")); + break; + } + complete(pm8001_dev->dcompletion); + ccb->task = NULL; + ccb->ccb_tag = 0xFFFFFFFF; + pm8001_ccb_free(pm8001_ha, htag); + return 0; +} + +static int mpi_dereg_resp(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + u32 status; + u32 device_id; + struct dev_reg_resp *registerRespPayload = + (struct dev_reg_resp *)(piomb + 4); + + status = le32_to_cpu(registerRespPayload->status); + device_id = le32_to_cpu(registerRespPayload->device_id); + if (status != 0) + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" deregister device failed ,status = %x" + ", device_id = %x\n", status, device_id)); + return 0; +} + +static int +mpi_fw_flash_update_resp(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + u32 status; + struct fw_control_ex fw_control_context; + struct fw_flash_Update_resp *ppayload = + (struct fw_flash_Update_resp *)(piomb + 4); + u32 tag = le32_to_cpu(ppayload->tag); + struct pm8001_ccb_info *ccb = &pm8001_ha->ccb_info[tag]; + status = le32_to_cpu(ppayload->status); + memcpy(&fw_control_context, + ccb->fw_control_context, + sizeof(fw_control_context)); + switch (status) { + case FLASH_UPDATE_COMPLETE_PENDING_REBOOT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_COMPLETE_PENDING_REBOOT\n")); + break; + case FLASH_UPDATE_IN_PROGRESS: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_IN_PROGRESS\n")); + break; + case FLASH_UPDATE_HDR_ERR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_HDR_ERR\n")); + break; + case FLASH_UPDATE_OFFSET_ERR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_OFFSET_ERR\n")); + break; + case FLASH_UPDATE_CRC_ERR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_CRC_ERR\n")); + break; + case FLASH_UPDATE_LENGTH_ERR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_LENGTH_ERR\n")); + break; + case FLASH_UPDATE_HW_ERR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_HW_ERR\n")); + break; + case FLASH_UPDATE_DNLD_NOT_SUPPORTED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_DNLD_NOT_SUPPORTED\n")); + break; + case FLASH_UPDATE_DISABLED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(": FLASH_UPDATE_DISABLED\n")); + break; + default: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("No matched status = %d\n", status)); + break; + } + ccb->fw_control_context->fw_control->retcode = status; + pci_free_consistent(pm8001_ha->pdev, + fw_control_context.len, + fw_control_context.virtAddr, + fw_control_context.phys_addr); + complete(pm8001_ha->nvmd_completion); + ccb->task = NULL; + ccb->ccb_tag = 0xFFFFFFFF; + pm8001_ccb_free(pm8001_ha, tag); + return 0; +} + +static int +mpi_general_event(struct pm8001_hba_info *pm8001_ha , void *piomb) +{ + u32 status; + int i; + struct general_event_resp *pPayload = + (struct general_event_resp *)(piomb + 4); + status = le32_to_cpu(pPayload->status); + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk(" status = 0x%x\n", status)); + for (i = 0; i < GENERAL_EVENT_PAYLOAD; i++) + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("inb_IOMB_payload[0x%x] 0x%x, \n", i, + pPayload->inb_IOMB_payload[i])); + return 0; +} + +static int +mpi_task_abort_resp(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + struct sas_task *t; + struct pm8001_ccb_info *ccb; + unsigned long flags; + u32 status ; + u32 tag, scp; + struct task_status_struct *ts; + + struct task_abort_resp *pPayload = + (struct task_abort_resp *)(piomb + 4); + ccb = &pm8001_ha->ccb_info[pPayload->tag]; + t = ccb->task; + ts = &t->task_status; + + if (t == NULL) + return -1; + + status = le32_to_cpu(pPayload->status); + tag = le32_to_cpu(pPayload->tag); + scp = le32_to_cpu(pPayload->scp); + PM8001_IO_DBG(pm8001_ha, + pm8001_printk(" status = 0x%x\n", status)); + if (status != 0) + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("task abort failed tag = 0x%x," + " scp= 0x%x\n", tag, scp)); + switch (status) { + case IO_SUCCESS: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_SUCCESS\n")); + ts->resp = SAS_TASK_COMPLETE; + ts->stat = SAM_GOOD; + break; + case IO_NOT_VALID: + PM8001_IO_DBG(pm8001_ha, pm8001_printk("IO_NOT_VALID\n")); + ts->resp = TMF_RESP_FUNC_FAILED; + break; + } + spin_lock_irqsave(&t->task_state_lock, flags); + t->task_state_flags &= ~SAS_TASK_STATE_PENDING; + t->task_state_flags &= ~SAS_TASK_AT_INITIATOR; + t->task_state_flags |= SAS_TASK_STATE_DONE; + spin_unlock_irqrestore(&t->task_state_lock, flags); + pm8001_ccb_task_free(pm8001_ha, t, ccb, pPayload->tag); + mb(); + t->task_done(t); + return 0; +} + +/** + * mpi_hw_event -The hw event has come. + * @pm8001_ha: our hba card information + * @piomb: IO message buffer + */ +static int mpi_hw_event(struct pm8001_hba_info *pm8001_ha, void* piomb) +{ + unsigned long flags; + struct hw_event_resp *pPayload = + (struct hw_event_resp *)(piomb + 4); + u32 lr_evt_status_phyid_portid = + le32_to_cpu(pPayload->lr_evt_status_phyid_portid); + u8 port_id = (u8)(lr_evt_status_phyid_portid & 0x0000000F); + u8 phy_id = + (u8)((lr_evt_status_phyid_portid & 0x000000F0) >> 4); + u16 eventType = + (u16)((lr_evt_status_phyid_portid & 0x00FFFF00) >> 8); + u8 status = + (u8)((lr_evt_status_phyid_portid & 0x0F000000) >> 24); + struct sas_ha_struct *sas_ha = pm8001_ha->sas; + struct pm8001_phy *phy = &pm8001_ha->phy[phy_id]; + struct asd_sas_phy *sas_phy = sas_ha->sas_phy[phy_id]; + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("outbound queue HW event & event type : ")); + switch (eventType) { + case HW_EVENT_PHY_START_STATUS: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PHY_START_STATUS" + " status = %x\n", status)); + if (status == 0) { + phy->phy_state = 1; + if (pm8001_ha->flags == PM8001F_RUN_TIME) + complete(phy->enable_completion); + } + break; + case HW_EVENT_SAS_PHY_UP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PHY_START_STATUS \n")); + hw_event_sas_phy_up(pm8001_ha, piomb); + break; + case HW_EVENT_SATA_PHY_UP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_SATA_PHY_UP \n")); + hw_event_sata_phy_up(pm8001_ha, piomb); + break; + case HW_EVENT_PHY_STOP_STATUS: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PHY_STOP_STATUS " + "status = %x\n", status)); + if (status == 0) + phy->phy_state = 0; + break; + case HW_EVENT_SATA_SPINUP_HOLD: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_SATA_SPINUP_HOLD \n")); + sas_ha->notify_phy_event(&phy->sas_phy, PHYE_SPINUP_HOLD); + break; + case HW_EVENT_PHY_DOWN: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PHY_DOWN \n")); + sas_ha->notify_phy_event(&phy->sas_phy, PHYE_LOSS_OF_SIGNAL); + phy->phy_attached = 0; + phy->phy_state = 0; + hw_event_phy_down(pm8001_ha, piomb); + break; + case HW_EVENT_PORT_INVALID: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PORT_INVALID\n")); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + /* the broadcast change primitive received, tell the LIBSAS this event + to revalidate the sas domain*/ + case HW_EVENT_BROADCAST_CHANGE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_BROADCAST_CHANGE\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, HW_EVENT_BROADCAST_CHANGE, + port_id, phy_id, 1, 0); + spin_lock_irqsave(&sas_phy->sas_prim_lock, flags); + sas_phy->sas_prim = HW_EVENT_BROADCAST_CHANGE; + spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags); + sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD); + break; + case HW_EVENT_PHY_ERROR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PHY_ERROR\n")); + sas_phy_disconnected(&phy->sas_phy); + phy->phy_attached = 0; + sas_ha->notify_phy_event(&phy->sas_phy, PHYE_OOB_ERROR); + break; + case HW_EVENT_BROADCAST_EXP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_BROADCAST_EXP\n")); + spin_lock_irqsave(&sas_phy->sas_prim_lock, flags); + sas_phy->sas_prim = HW_EVENT_BROADCAST_EXP; + spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags); + sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD); + break; + case HW_EVENT_LINK_ERR_INVALID_DWORD: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_LINK_ERR_INVALID_DWORD\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, + HW_EVENT_LINK_ERR_INVALID_DWORD, port_id, phy_id, 0, 0); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_LINK_ERR_DISPARITY_ERROR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_LINK_ERR_DISPARITY_ERROR\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, + HW_EVENT_LINK_ERR_DISPARITY_ERROR, + port_id, phy_id, 0, 0); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_LINK_ERR_CODE_VIOLATION: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_LINK_ERR_CODE_VIOLATION\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, + HW_EVENT_LINK_ERR_CODE_VIOLATION, + port_id, phy_id, 0, 0); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, + HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH, + port_id, phy_id, 0, 0); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_MALFUNCTION: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_MALFUNCTION\n")); + break; + case HW_EVENT_BROADCAST_SES: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_BROADCAST_SES\n")); + spin_lock_irqsave(&sas_phy->sas_prim_lock, flags); + sas_phy->sas_prim = HW_EVENT_BROADCAST_SES; + spin_unlock_irqrestore(&sas_phy->sas_prim_lock, flags); + sas_ha->notify_port_event(sas_phy, PORTE_BROADCAST_RCVD); + break; + case HW_EVENT_INBOUND_CRC_ERROR: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_INBOUND_CRC_ERROR\n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, + HW_EVENT_INBOUND_CRC_ERROR, + port_id, phy_id, 0, 0); + break; + case HW_EVENT_HARD_RESET_RECEIVED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_HARD_RESET_RECEIVED\n")); + sas_ha->notify_port_event(sas_phy, PORTE_HARD_RESET); + break; + case HW_EVENT_ID_FRAME_TIMEOUT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_ID_FRAME_TIMEOUT\n")); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_LINK_ERR_PHY_RESET_FAILED: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_LINK_ERR_PHY_RESET_FAILED \n")); + pm8001_hw_event_ack_req(pm8001_ha, 0, + HW_EVENT_LINK_ERR_PHY_RESET_FAILED, + port_id, phy_id, 0, 0); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_PORT_RESET_TIMER_TMO: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PORT_RESET_TIMER_TMO \n")); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_PORT_RECOVERY_TIMER_TMO: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PORT_RECOVERY_TIMER_TMO \n")); + sas_phy_disconnected(sas_phy); + phy->phy_attached = 0; + sas_ha->notify_port_event(sas_phy, PORTE_LINK_RESET_ERR); + break; + case HW_EVENT_PORT_RECOVER: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PORT_RECOVER \n")); + break; + case HW_EVENT_PORT_RESET_COMPLETE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("HW_EVENT_PORT_RESET_COMPLETE \n")); + break; + case EVENT_BROADCAST_ASYNCH_EVENT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("EVENT_BROADCAST_ASYNCH_EVENT\n")); + break; + default: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("Unknown event type = %x\n", eventType)); + break; + } + return 0; +} + +/** + * process_one_iomb - process one outbound Queue memory block + * @pm8001_ha: our hba card information + * @piomb: IO message buffer + */ +static void process_one_iomb(struct pm8001_hba_info *pm8001_ha, void *piomb) +{ + u32 pHeader = (u32)*(u32 *)piomb; + u8 opc = (u8)((le32_to_cpu(pHeader)) & 0xFFF); + + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("process_one_iomb:\n")); + + switch (opc) { + case OPC_OUB_ECHO: + PM8001_MSG_DBG(pm8001_ha, pm8001_printk("OPC_OUB_ECHO \n")); + break; + case OPC_OUB_HW_EVENT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_HW_EVENT \n")); + mpi_hw_event(pm8001_ha, piomb); + break; + case OPC_OUB_SSP_COMP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SSP_COMP \n")); + mpi_ssp_completion(pm8001_ha, piomb); + break; + case OPC_OUB_SMP_COMP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SMP_COMP \n")); + mpi_smp_completion(pm8001_ha, piomb); + break; + case OPC_OUB_LOCAL_PHY_CNTRL: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_LOCAL_PHY_CNTRL\n")); + mpi_local_phy_ctl(pm8001_ha, piomb); + break; + case OPC_OUB_DEV_REGIST: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_DEV_REGIST \n")); + mpi_reg_resp(pm8001_ha, piomb); + break; + case OPC_OUB_DEREG_DEV: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("unresgister the deviece \n")); + mpi_dereg_resp(pm8001_ha, piomb); + break; + case OPC_OUB_GET_DEV_HANDLE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_GET_DEV_HANDLE \n")); + break; + case OPC_OUB_SATA_COMP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SATA_COMP \n")); + mpi_sata_completion(pm8001_ha, piomb); + break; + case OPC_OUB_SATA_EVENT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SATA_EVENT \n")); + mpi_sata_event(pm8001_ha, piomb); + break; + case OPC_OUB_SSP_EVENT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SSP_EVENT\n")); + mpi_ssp_event(pm8001_ha, piomb); + break; + case OPC_OUB_DEV_HANDLE_ARRIV: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_DEV_HANDLE_ARRIV\n")); + /*This is for target*/ + break; + case OPC_OUB_SSP_RECV_EVENT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SSP_RECV_EVENT\n")); + /*This is for target*/ + break; + case OPC_OUB_DEV_INFO: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_DEV_INFO\n")); + break; + case OPC_OUB_FW_FLASH_UPDATE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_FW_FLASH_UPDATE\n")); + mpi_fw_flash_update_resp(pm8001_ha, piomb); + break; + case OPC_OUB_GPIO_RESPONSE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_GPIO_RESPONSE\n")); + break; + case OPC_OUB_GPIO_EVENT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_GPIO_EVENT\n")); + break; + case OPC_OUB_GENERAL_EVENT: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_GENERAL_EVENT\n")); + mpi_general_event(pm8001_ha, piomb); + break; + case OPC_OUB_SSP_ABORT_RSP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SSP_ABORT_RSP\n")); + mpi_task_abort_resp(pm8001_ha, piomb); + break; + case OPC_OUB_SATA_ABORT_RSP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SATA_ABORT_RSP\n")); + mpi_task_abort_resp(pm8001_ha, piomb); + break; + case OPC_OUB_SAS_DIAG_MODE_START_END: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SAS_DIAG_MODE_START_END\n")); + break; + case OPC_OUB_SAS_DIAG_EXECUTE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SAS_DIAG_EXECUTE\n")); + break; + case OPC_OUB_GET_TIME_STAMP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_GET_TIME_STAMP\n")); + break; + case OPC_OUB_SAS_HW_EVENT_ACK: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SAS_HW_EVENT_ACK\n")); + break; + case OPC_OUB_PORT_CONTROL: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_PORT_CONTROL\n")); + break; + case OPC_OUB_SMP_ABORT_RSP: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SMP_ABORT_RSP\n")); + mpi_task_abort_resp(pm8001_ha, piomb); + break; + case OPC_OUB_GET_NVMD_DATA: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_GET_NVMD_DATA\n")); + mpi_get_nvmd_resp(pm8001_ha, piomb); + break; + case OPC_OUB_SET_NVMD_DATA: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SET_NVMD_DATA\n")); + mpi_set_nvmd_resp(pm8001_ha, piomb); + break; + case OPC_OUB_DEVICE_HANDLE_REMOVAL: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_DEVICE_HANDLE_REMOVAL\n")); + break; + case OPC_OUB_SET_DEVICE_STATE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SET_DEVICE_STATE\n")); + mpi_set_dev_state_resp(pm8001_ha, piomb); + break; + case OPC_OUB_GET_DEVICE_STATE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_GET_DEVICE_STATE\n")); + break; + case OPC_OUB_SET_DEV_INFO: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SET_DEV_INFO\n")); + break; + case OPC_OUB_SAS_RE_INITIALIZE: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("OPC_OUB_SAS_RE_INITIALIZE\n")); + break; + default: + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("Unknown outbound Queue IOMB OPC = %x\n", + opc)); + break; + } +} + +static int process_oq(struct pm8001_hba_info *pm8001_ha) +{ + struct outbound_queue_table *circularQ; + void *pMsg1 = NULL; + u8 bc = 0; + u32 ret = MPI_IO_STATUS_FAIL, processedMsgCount = 0; + + circularQ = &pm8001_ha->outbnd_q_tbl[0]; + do { + ret = mpi_msg_consume(pm8001_ha, circularQ, &pMsg1, &bc); + if (MPI_IO_STATUS_SUCCESS == ret) { + /* process the outbound message */ + process_one_iomb(pm8001_ha, (void *)((u8 *)pMsg1 - 4)); + /* free the message from the outbound circular buffer */ + mpi_msg_free_set(pm8001_ha, circularQ, bc); + processedMsgCount++; + } + if (MPI_IO_STATUS_BUSY == ret) { + u32 producer_idx; + /* Update the producer index from SPC */ + producer_idx = pm8001_read_32(circularQ->pi_virt); + circularQ->producer_index = cpu_to_le32(producer_idx); + if (circularQ->producer_index == + circularQ->consumer_idx) + /* OQ is empty */ + break; + } + } while (100 > processedMsgCount);/*end message processing if hit the + count*/ + return ret; +} + +/* PCI_DMA_... to our direction translation. */ +static const u8 data_dir_flags[] = { + [PCI_DMA_BIDIRECTIONAL] = DATA_DIR_BYRECIPIENT,/* UNSPECIFIED */ + [PCI_DMA_TODEVICE] = DATA_DIR_OUT,/* OUTBOUND */ + [PCI_DMA_FROMDEVICE] = DATA_DIR_IN,/* INBOUND */ + [PCI_DMA_NONE] = DATA_DIR_NONE,/* NO TRANSFER */ +}; +static void +pm8001_chip_make_sg(struct scatterlist *scatter, int nr, void *prd) +{ + int i; + struct scatterlist *sg; + struct pm8001_prd *buf_prd = prd; + + for_each_sg(scatter, sg, nr, i) { + buf_prd->addr = cpu_to_le64(sg_dma_address(sg)); + buf_prd->im_len.len = cpu_to_le32(sg_dma_len(sg)); + buf_prd->im_len.e = 0; + buf_prd++; + } +} + +static void build_smp_cmd(u32 deviceID, u32 hTag, struct smp_req *psmp_cmd) +{ + psmp_cmd->tag = cpu_to_le32(hTag); + psmp_cmd->device_id = cpu_to_le32(deviceID); + psmp_cmd->len_ip_ir = cpu_to_le32(1|(1 << 1)); +} + +/** + * pm8001_chip_smp_req - send a SMP task to FW + * @pm8001_ha: our hba card information. + * @ccb: the ccb information this request used. + */ +static int pm8001_chip_smp_req(struct pm8001_hba_info *pm8001_ha, + struct pm8001_ccb_info *ccb) +{ + int elem, rc; + struct sas_task *task = ccb->task; + struct domain_device *dev = task->dev; + struct pm8001_device *pm8001_dev = dev->lldd_dev; + struct scatterlist *sg_req, *sg_resp; + u32 req_len, resp_len; + struct smp_req smp_cmd; + u32 opc; + struct inbound_queue_table *circularQ; + + memset(&smp_cmd, 0, sizeof(smp_cmd)); + /* + * DMA-map SMP request, response buffers + */ + sg_req = &task->smp_task.smp_req; + elem = dma_map_sg(pm8001_ha->dev, sg_req, 1, PCI_DMA_TODEVICE); + if (!elem) + return -ENOMEM; + req_len = sg_dma_len(sg_req); + + sg_resp = &task->smp_task.smp_resp; + elem = dma_map_sg(pm8001_ha->dev, sg_resp, 1, PCI_DMA_FROMDEVICE); + if (!elem) { + rc = -ENOMEM; + goto err_out; + } + resp_len = sg_dma_len(sg_resp); + /* must be in dwords */ + if ((req_len & 0x3) || (resp_len & 0x3)) { + rc = -EINVAL; + goto err_out_2; + } + + opc = OPC_INB_SMP_REQUEST; + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + smp_cmd.tag = cpu_to_le32(ccb->ccb_tag); + smp_cmd.long_smp_req.long_req_addr = + cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_req)); + smp_cmd.long_smp_req.long_req_size = + cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_req)-4); + smp_cmd.long_smp_req.long_resp_addr = + cpu_to_le64((u64)sg_dma_address(&task->smp_task.smp_resp)); + smp_cmd.long_smp_req.long_resp_size = + cpu_to_le32((u32)sg_dma_len(&task->smp_task.smp_resp)-4); + build_smp_cmd(pm8001_dev->device_id, smp_cmd.tag, &smp_cmd); + mpi_build_cmd(pm8001_ha, circularQ, opc, (u32 *)&smp_cmd); + return 0; + +err_out_2: + dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_resp, 1, + PCI_DMA_FROMDEVICE); +err_out: + dma_unmap_sg(pm8001_ha->dev, &ccb->task->smp_task.smp_req, 1, + PCI_DMA_TODEVICE); + return rc; +} + +/** + * pm8001_chip_ssp_io_req - send a SSP task to FW + * @pm8001_ha: our hba card information. + * @ccb: the ccb information this request used. + */ +static int pm8001_chip_ssp_io_req(struct pm8001_hba_info *pm8001_ha, + struct pm8001_ccb_info *ccb) +{ + struct sas_task *task = ccb->task; + struct domain_device *dev = task->dev; + struct pm8001_device *pm8001_dev = dev->lldd_dev; + struct ssp_ini_io_start_req ssp_cmd; + u32 tag = ccb->ccb_tag; + __le64 phys_addr; + struct inbound_queue_table *circularQ; + u32 opc = OPC_INB_SSPINIIOSTART; + memset(&ssp_cmd, 0, sizeof(ssp_cmd)); + memcpy(ssp_cmd.ssp_iu.lun, task->ssp_task.LUN, 8); + ssp_cmd.dir_m_tlr = data_dir_flags[task->data_dir] << 8 | 0x0;/*0 for + SAS 1.1 compatible TLR*/ + ssp_cmd.data_len = cpu_to_le32(task->total_xfer_len); + ssp_cmd.device_id = cpu_to_le32(pm8001_dev->device_id); + ssp_cmd.tag = cpu_to_le32(tag); + if (task->ssp_task.enable_first_burst) + ssp_cmd.ssp_iu.efb_prio_attr |= 0x80; + ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_prio << 3); + ssp_cmd.ssp_iu.efb_prio_attr |= (task->ssp_task.task_attr & 7); + memcpy(ssp_cmd.ssp_iu.cdb, task->ssp_task.cdb, 16); + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + + /* fill in PRD (scatter/gather) table, if any */ + if (task->num_scatter > 1) { + pm8001_chip_make_sg(task->scatter, ccb->n_elem, ccb->buf_prd); + phys_addr = cpu_to_le64(ccb->ccb_dma_handle + + offsetof(struct pm8001_ccb_info, buf_prd[0])); + ssp_cmd.addr_low = lower_32_bits(phys_addr); + ssp_cmd.addr_high = upper_32_bits(phys_addr); + ssp_cmd.esgl = cpu_to_le32(1<<31); + } else if (task->num_scatter == 1) { + __le64 dma_addr = cpu_to_le64(sg_dma_address(task->scatter)); + ssp_cmd.addr_low = lower_32_bits(dma_addr); + ssp_cmd.addr_high = upper_32_bits(dma_addr); + ssp_cmd.len = cpu_to_le32(task->total_xfer_len); + ssp_cmd.esgl = 0; + } else if (task->num_scatter == 0) { + ssp_cmd.addr_low = 0; + ssp_cmd.addr_high = 0; + ssp_cmd.len = cpu_to_le32(task->total_xfer_len); + ssp_cmd.esgl = 0; + } + mpi_build_cmd(pm8001_ha, circularQ, opc, &ssp_cmd); + return 0; +} + +static int pm8001_chip_sata_req(struct pm8001_hba_info *pm8001_ha, + struct pm8001_ccb_info *ccb) +{ + struct sas_task *task = ccb->task; + struct domain_device *dev = task->dev; + struct pm8001_device *pm8001_ha_dev = dev->lldd_dev; + u32 tag = ccb->ccb_tag; + struct sata_start_req sata_cmd; + u32 hdr_tag, ncg_tag = 0; + __le64 phys_addr; + u32 ATAP = 0x0; + u32 dir; + struct inbound_queue_table *circularQ; + u32 opc = OPC_INB_SATA_HOST_OPSTART; + memset(&sata_cmd, 0, sizeof(sata_cmd)); + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + if (task->data_dir == PCI_DMA_NONE) { + ATAP = 0x04; /* no data*/ + PM8001_IO_DBG(pm8001_ha, pm8001_printk("no data \n")); + } else if (likely(!task->ata_task.device_control_reg_update)) { + if (task->ata_task.dma_xfer) { + ATAP = 0x06; /* DMA */ + PM8001_IO_DBG(pm8001_ha, pm8001_printk("DMA \n")); + } else { + ATAP = 0x05; /* PIO*/ + PM8001_IO_DBG(pm8001_ha, pm8001_printk("PIO \n")); + } + if (task->ata_task.use_ncq && + dev->sata_dev.command_set != ATAPI_COMMAND_SET) { + ATAP = 0x07; /* FPDMA */ + PM8001_IO_DBG(pm8001_ha, pm8001_printk("FPDMA \n")); + } + } + if (task->ata_task.use_ncq && pm8001_get_ncq_tag(task, &hdr_tag)) + ncg_tag = cpu_to_le32(hdr_tag); + dir = data_dir_flags[task->data_dir] << 8; + sata_cmd.tag = cpu_to_le32(tag); + sata_cmd.device_id = cpu_to_le32(pm8001_ha_dev->device_id); + sata_cmd.data_len = cpu_to_le32(task->total_xfer_len); + sata_cmd.ncqtag_atap_dir_m = + cpu_to_le32(((ncg_tag & 0xff)<<16)|((ATAP & 0x3f) << 10) | dir); + sata_cmd.sata_fis = task->ata_task.fis; + if (likely(!task->ata_task.device_control_reg_update)) + sata_cmd.sata_fis.flags |= 0x80;/* C=1: update ATA cmd reg */ + sata_cmd.sata_fis.flags &= 0xF0;/* PM_PORT field shall be 0 */ + /* fill in PRD (scatter/gather) table, if any */ + if (task->num_scatter > 1) { + pm8001_chip_make_sg(task->scatter, ccb->n_elem, ccb->buf_prd); + phys_addr = cpu_to_le64(ccb->ccb_dma_handle + + offsetof(struct pm8001_ccb_info, buf_prd[0])); + sata_cmd.addr_low = lower_32_bits(phys_addr); + sata_cmd.addr_high = upper_32_bits(phys_addr); + sata_cmd.esgl = cpu_to_le32(1 << 31); + } else if (task->num_scatter == 1) { + __le64 dma_addr = cpu_to_le64(sg_dma_address(task->scatter)); + sata_cmd.addr_low = lower_32_bits(dma_addr); + sata_cmd.addr_high = upper_32_bits(dma_addr); + sata_cmd.len = cpu_to_le32(task->total_xfer_len); + sata_cmd.esgl = 0; + } else if (task->num_scatter == 0) { + sata_cmd.addr_low = 0; + sata_cmd.addr_high = 0; + sata_cmd.len = cpu_to_le32(task->total_xfer_len); + sata_cmd.esgl = 0; + } + mpi_build_cmd(pm8001_ha, circularQ, opc, &sata_cmd); + return 0; +} + +/** + * pm8001_chip_phy_start_req - start phy via PHY_START COMMAND + * @pm8001_ha: our hba card information. + * @num: the inbound queue number + * @phy_id: the phy id which we wanted to start up. + */ +static int +pm8001_chip_phy_start_req(struct pm8001_hba_info *pm8001_ha, u8 phy_id) +{ + struct phy_start_req payload; + struct inbound_queue_table *circularQ; + u32 tag = 0x01; + u32 opcode = OPC_INB_PHYSTART; + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + memset(&payload, 0, sizeof(payload)); + payload.tag = cpu_to_le32(tag); + /* + ** [0:7] PHY Identifier + ** [8:11] link rate 1.5G, 3G, 6G + ** [12:13] link mode 01b SAS mode; 10b SATA mode; 11b both + ** [14] 0b disable spin up hold; 1b enable spin up hold + */ + payload.ase_sh_lm_slr_phyid = cpu_to_le32(SPINHOLD_DISABLE | + LINKMODE_AUTO | LINKRATE_15 | + LINKRATE_30 | LINKRATE_60 | phy_id); + payload.sas_identify.dev_type = SAS_END_DEV; + payload.sas_identify.initiator_bits = SAS_PROTOCOL_ALL; + memcpy(payload.sas_identify.sas_addr, + pm8001_ha->sas_addr, SAS_ADDR_SIZE); + payload.sas_identify.phy_id = phy_id; + mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload); + return 0; +} + +/** + * pm8001_chip_phy_stop_req - start phy via PHY_STOP COMMAND + * @pm8001_ha: our hba card information. + * @num: the inbound queue number + * @phy_id: the phy id which we wanted to start up. + */ +static int pm8001_chip_phy_stop_req(struct pm8001_hba_info *pm8001_ha, + u8 phy_id) +{ + struct phy_stop_req payload; + struct inbound_queue_table *circularQ; + u32 tag = 0x01; + u32 opcode = OPC_INB_PHYSTOP; + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + memset(&payload, 0, sizeof(payload)); + payload.tag = cpu_to_le32(tag); + payload.phy_id = cpu_to_le32(phy_id); + mpi_build_cmd(pm8001_ha, circularQ, opcode, &payload); + return 0; +} + +/** + * see comments on mpi_reg_resp. + */ +static int pm8001_chip_reg_dev_req(struct pm8001_hba_info *pm8001_ha, + struct pm8001_device *pm8001_dev, u32 flag) +{ + struct reg_dev_req payload; + u32 opc; + u32 stp_sspsmp_sata = 0x4; + struct inbound_queue_table *circularQ; + u32 linkrate, phy_id; + u32 rc, tag = 0xdeadbeef; + struct pm8001_ccb_info *ccb; + u8 retryFlag = 0x1; + u16 firstBurstSize = 0; + u16 ITNT = 2000; + struct domain_device *dev = pm8001_dev->sas_device; + struct domain_device *parent_dev = dev->parent; + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + + memset(&payload, 0, sizeof(payload)); + rc = pm8001_tag_alloc(pm8001_ha, &tag); + if (rc) + return rc; + ccb = &pm8001_ha->ccb_info[tag]; + ccb->device = pm8001_dev; + ccb->ccb_tag = tag; + payload.tag = cpu_to_le32(tag); + if (flag == 1) + stp_sspsmp_sata = 0x02; /*direct attached sata */ + else { + if (pm8001_dev->dev_type == SATA_DEV) + stp_sspsmp_sata = 0x00; /* stp*/ + else if (pm8001_dev->dev_type == SAS_END_DEV || + pm8001_dev->dev_type == EDGE_DEV || + pm8001_dev->dev_type == FANOUT_DEV) + stp_sspsmp_sata = 0x01; /*ssp or smp*/ + } + if (parent_dev && DEV_IS_EXPANDER(parent_dev->dev_type)) + phy_id = parent_dev->ex_dev.ex_phy->phy_id; + else + phy_id = pm8001_dev->attached_phy; + opc = OPC_INB_REG_DEV; + linkrate = (pm8001_dev->sas_device->linkrate < dev->port->linkrate) ? + pm8001_dev->sas_device->linkrate : dev->port->linkrate; + payload.phyid_portid = + cpu_to_le32(((pm8001_dev->sas_device->port->id) & 0x0F) | + ((phy_id & 0x0F) << 4)); + payload.dtype_dlr_retry = cpu_to_le32((retryFlag & 0x01) | + ((linkrate & 0x0F) * 0x1000000) | + ((stp_sspsmp_sata & 0x03) * 0x10000000)); + payload.firstburstsize_ITNexustimeout = + cpu_to_le32(ITNT | (firstBurstSize * 0x10000)); + memcpy(&payload.sas_addr_hi, pm8001_dev->sas_device->sas_addr, + SAS_ADDR_SIZE); + mpi_build_cmd(pm8001_ha, circularQ, opc, &payload); + return 0; +} + +/** + * see comments on mpi_reg_resp. + */ +static int pm8001_chip_dereg_dev_req(struct pm8001_hba_info *pm8001_ha, + u32 device_id) +{ + struct dereg_dev_req payload; + u32 opc = OPC_INB_DEREG_DEV_HANDLE; + struct inbound_queue_table *circularQ; + + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + memset((u8 *)&payload, 0, sizeof(payload)); + payload.tag = 1; + payload.device_id = cpu_to_le32(device_id); + PM8001_MSG_DBG(pm8001_ha, + pm8001_printk("unregister device device_id = %d\n", device_id)); + mpi_build_cmd(pm8001_ha, circularQ, opc, &payload); + return 0; +} + +/** + * pm8001_chip_phy_ctl_req - support the local phy operation + * @pm8001_ha: our hba card information. + * @num: the inbound queue number + * @phy_id: the phy id which we wanted to operate + * @phy_op: + */ +static int pm8001_chip_phy_ctl_req(struct pm8001_hba_info *pm8001_ha, + u32 phyId, u32 phy_op) +{ + struct local_phy_ctl_req payload; + struct inbound_queue_table *circularQ; + u32 opc = OPC_INB_LOCAL_PHY_CONTROL; + memset((u8 *)&payload, 0, sizeof(payload)); + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + payload.tag = 1; + payload.phyop_phyid = + cpu_to_le32(((phy_op & 0xff) << 8) | (phyId & 0x0F)); + mpi_build_cmd(pm8001_ha, circularQ, opc, &payload); + return 0; +} + +static u32 pm8001_chip_is_our_interupt(struct pm8001_hba_info *pm8001_ha) +{ + u32 value; +#ifdef PM8001_USE_MSIX + return 1; +#endif + value = pm8001_cr32(pm8001_ha, 0, MSGU_ODR); + if (value) + return 1; + return 0; + +} + +/** + * pm8001_chip_isr - PM8001 isr handler. + * @pm8001_ha: our hba card information. + * @irq: irq number. + * @stat: stat. + */ +static void +pm8001_chip_isr(struct pm8001_hba_info *pm8001_ha) +{ + pm8001_chip_interrupt_disable(pm8001_ha); + process_oq(pm8001_ha); + pm8001_chip_interrupt_enable(pm8001_ha); +} + +static int send_task_abort(struct pm8001_hba_info *pm8001_ha, u32 opc, + u32 dev_id, u8 flag, u32 task_tag, u32 cmd_tag) +{ + struct task_abort_req task_abort; + struct inbound_queue_table *circularQ; + + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + memset(&task_abort, 0, sizeof(task_abort)); + if (ABORT_SINGLE == (flag & ABORT_MASK)) { + task_abort.abort_all = 0; + task_abort.device_id = cpu_to_le32(dev_id); + task_abort.tag_to_abort = cpu_to_le32(task_tag); + task_abort.tag = cpu_to_le32(cmd_tag); + } else if (ABORT_ALL == (flag & ABORT_MASK)) { + task_abort.abort_all = cpu_to_le32(1); + task_abort.device_id = cpu_to_le32(dev_id); + task_abort.tag = cpu_to_le32(cmd_tag); + } + mpi_build_cmd(pm8001_ha, circularQ, opc, &task_abort); + return 0; +} + +/** + * pm8001_chip_abort_task - SAS abort task when error or exception happened. + * @task: the task we wanted to aborted. + * @flag: the abort flag. + */ +static int pm8001_chip_abort_task(struct pm8001_hba_info *pm8001_ha, + struct pm8001_device *pm8001_dev, u8 flag, u32 task_tag, u32 cmd_tag) +{ + u32 opc, device_id; + int rc = TMF_RESP_FUNC_FAILED; + PM8001_IO_DBG(pm8001_ha, pm8001_printk("Abort tag[%x]", task_tag)); + if (pm8001_dev->dev_type == SAS_END_DEV) + opc = OPC_INB_SSP_ABORT; + else if (pm8001_dev->dev_type == SATA_DEV) + opc = OPC_INB_SATA_ABORT; + else + opc = OPC_INB_SMP_ABORT;/* SMP */ + device_id = pm8001_dev->device_id; + rc = send_task_abort(pm8001_ha, opc, device_id, flag, + task_tag, cmd_tag); + if (rc != TMF_RESP_FUNC_COMPLETE) + PM8001_IO_DBG(pm8001_ha, pm8001_printk("rc= %d\n", rc)); + return rc; +} + +/** + * pm8001_chip_ssp_tm_req - built the task managment command. + * @pm8001_ha: our hba card information. + * @ccb: the ccb information. + * @tmf: task management function. + */ +static int pm8001_chip_ssp_tm_req(struct pm8001_hba_info *pm8001_ha, + struct pm8001_ccb_info *ccb, struct pm8001_tmf_task *tmf) +{ + struct sas_task *task = ccb->task; + struct domain_device *dev = task->dev; + struct pm8001_device *pm8001_dev = dev->lldd_dev; + u32 opc = OPC_INB_SSPINITMSTART; + struct inbound_queue_table *circularQ; + struct ssp_ini_tm_start_req sspTMCmd; + + memset(&sspTMCmd, 0, sizeof(sspTMCmd)); + sspTMCmd.device_id = cpu_to_le32(pm8001_dev->device_id); + sspTMCmd.relate_tag = cpu_to_le32(tmf->tag_of_task_to_be_managed); + sspTMCmd.tmf = cpu_to_le32(tmf->tmf); + sspTMCmd.ds_ads_m = cpu_to_le32(1 << 2); + memcpy(sspTMCmd.lun, task->ssp_task.LUN, 8); + sspTMCmd.tag = cpu_to_le32(ccb->ccb_tag); + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + mpi_build_cmd(pm8001_ha, circularQ, opc, &sspTMCmd); + return 0; +} + +static int pm8001_chip_get_nvmd_req(struct pm8001_hba_info *pm8001_ha, + void *payload) +{ + u32 opc = OPC_INB_GET_NVMD_DATA; + u32 nvmd_type; + u32 rc; + u32 tag; + struct pm8001_ccb_info *ccb; + struct inbound_queue_table *circularQ; + struct get_nvm_data_req nvmd_req; + struct fw_control_ex *fw_control_context; + struct pm8001_ioctl_payload *ioctl_payload = payload; + + nvmd_type = ioctl_payload->minor_function; + fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL); + fw_control_context->usrAddr = (u8 *)&ioctl_payload->func_specific[0]; + fw_control_context->len = ioctl_payload->length; + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + memset(&nvmd_req, 0, sizeof(nvmd_req)); + rc = pm8001_tag_alloc(pm8001_ha, &tag); + if (rc) + return rc; + ccb = &pm8001_ha->ccb_info[tag]; + ccb->ccb_tag = tag; + ccb->fw_control_context = fw_control_context; + nvmd_req.tag = cpu_to_le32(tag); + + switch (nvmd_type) { + case TWI_DEVICE: { + u32 twi_addr, twi_page_size; + twi_addr = 0xa8; + twi_page_size = 2; + + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | twi_addr << 16 | + twi_page_size << 8 | TWI_DEVICE); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + } + case C_SEEPROM: { + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | C_SEEPROM); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + } + case VPD_FLASH: { + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | VPD_FLASH); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + } + case EXPAN_ROM: { + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | EXPAN_ROM); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + } + default: + break; + } + mpi_build_cmd(pm8001_ha, circularQ, opc, &nvmd_req); + return 0; +} + +static int pm8001_chip_set_nvmd_req(struct pm8001_hba_info *pm8001_ha, + void *payload) +{ + u32 opc = OPC_INB_SET_NVMD_DATA; + u32 nvmd_type; + u32 rc; + u32 tag; + struct pm8001_ccb_info *ccb; + struct inbound_queue_table *circularQ; + struct set_nvm_data_req nvmd_req; + struct fw_control_ex *fw_control_context; + struct pm8001_ioctl_payload *ioctl_payload = payload; + + nvmd_type = ioctl_payload->minor_function; + fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL); + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + memcpy(pm8001_ha->memoryMap.region[NVMD].virt_ptr, + ioctl_payload->func_specific, + ioctl_payload->length); + memset(&nvmd_req, 0, sizeof(nvmd_req)); + rc = pm8001_tag_alloc(pm8001_ha, &tag); + if (rc) + return rc; + ccb = &pm8001_ha->ccb_info[tag]; + ccb->fw_control_context = fw_control_context; + ccb->ccb_tag = tag; + nvmd_req.tag = cpu_to_le32(tag); + switch (nvmd_type) { + case TWI_DEVICE: { + u32 twi_addr, twi_page_size; + twi_addr = 0xa8; + twi_page_size = 2; + nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98); + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | twi_addr << 16 | + twi_page_size << 8 | TWI_DEVICE); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + } + case C_SEEPROM: + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | C_SEEPROM); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + case VPD_FLASH: + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | VPD_FLASH); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + case EXPAN_ROM: + nvmd_req.len_ir_vpdd = cpu_to_le32(IPMode | EXPAN_ROM); + nvmd_req.resp_len = cpu_to_le32(ioctl_payload->length); + nvmd_req.reserved[0] = cpu_to_le32(0xFEDCBA98); + nvmd_req.resp_addr_hi = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_hi); + nvmd_req.resp_addr_lo = + cpu_to_le32(pm8001_ha->memoryMap.region[NVMD].phys_addr_lo); + break; + default: + break; + } + mpi_build_cmd(pm8001_ha, circularQ, opc, &nvmd_req); + return 0; +} + +/** + * pm8001_chip_fw_flash_update_build - support the firmware update operation + * @pm8001_ha: our hba card information. + * @fw_flash_updata_info: firmware flash update param + */ +static int +pm8001_chip_fw_flash_update_build(struct pm8001_hba_info *pm8001_ha, + void *fw_flash_updata_info, u32 tag) +{ + struct fw_flash_Update_req payload; + struct fw_flash_updata_info *info; + struct inbound_queue_table *circularQ; + u32 opc = OPC_INB_FW_FLASH_UPDATE; + + memset((u8 *)&payload, 0, sizeof(struct fw_flash_Update_req)); + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + info = fw_flash_updata_info; + payload.tag = cpu_to_le32(tag); + payload.cur_image_len = cpu_to_le32(info->cur_image_len); + payload.cur_image_offset = cpu_to_le32(info->cur_image_offset); + payload.total_image_len = cpu_to_le32(info->total_image_len); + payload.len = info->sgl.im_len.len ; + payload.sgl_addr_lo = lower_32_bits(info->sgl.addr); + payload.sgl_addr_hi = upper_32_bits(info->sgl.addr); + mpi_build_cmd(pm8001_ha, circularQ, opc, &payload); + return 0; +} + +static int +pm8001_chip_fw_flash_update_req(struct pm8001_hba_info *pm8001_ha, + void *payload) +{ + struct fw_flash_updata_info flash_update_info; + struct fw_control_info *fw_control; + struct fw_control_ex *fw_control_context; + u32 rc; + u32 tag; + struct pm8001_ccb_info *ccb; + void *buffer = NULL; + dma_addr_t phys_addr; + u32 phys_addr_hi; + u32 phys_addr_lo; + struct pm8001_ioctl_payload *ioctl_payload = payload; + + fw_control_context = kzalloc(sizeof(struct fw_control_ex), GFP_KERNEL); + fw_control = (struct fw_control_info *)&ioctl_payload->func_specific[0]; + if (fw_control->len != 0) { + if (pm8001_mem_alloc(pm8001_ha->pdev, + (void **)&buffer, + &phys_addr, + &phys_addr_hi, + &phys_addr_lo, + fw_control->len, 0) != 0) { + PM8001_FAIL_DBG(pm8001_ha, + pm8001_printk("Mem alloc failure\n")); + return -ENOMEM; + } + } + memset((void *)buffer, 0, fw_control->len); + memcpy((void *)buffer, fw_control->buffer, fw_control->len); + flash_update_info.sgl.addr = cpu_to_le64(phys_addr); + flash_update_info.sgl.im_len.len = cpu_to_le32(fw_control->len); + flash_update_info.sgl.im_len.e = 0; + flash_update_info.cur_image_offset = fw_control->offset; + flash_update_info.cur_image_len = fw_control->len; + flash_update_info.total_image_len = fw_control->size; + fw_control_context->fw_control = fw_control; + fw_control_context->virtAddr = buffer; + fw_control_context->len = fw_control->len; + rc = pm8001_tag_alloc(pm8001_ha, &tag); + if (rc) + return rc; + ccb = &pm8001_ha->ccb_info[tag]; + ccb->fw_control_context = fw_control_context; + ccb->ccb_tag = tag; + pm8001_chip_fw_flash_update_build(pm8001_ha, &flash_update_info, tag); + return 0; +} + +static int +pm8001_chip_set_dev_state_req(struct pm8001_hba_info *pm8001_ha, + struct pm8001_device *pm8001_dev, u32 state) +{ + struct set_dev_state_req payload; + struct inbound_queue_table *circularQ; + struct pm8001_ccb_info *ccb; + u32 rc; + u32 tag; + u32 opc = OPC_INB_SET_DEVICE_STATE; + memset((u8 *)&payload, 0, sizeof(payload)); + rc = pm8001_tag_alloc(pm8001_ha, &tag); + if (rc) + return -1; + ccb = &pm8001_ha->ccb_info[tag]; + ccb->ccb_tag = tag; + ccb->device = pm8001_dev; + circularQ = &pm8001_ha->inbnd_q_tbl[0]; + payload.tag = cpu_to_le32(tag); + payload.device_id = cpu_to_le32(pm8001_dev->device_id); + payload.nds = cpu_to_le32(state); + mpi_build_cmd(pm8001_ha, circularQ, opc, &payload); + return 0; + +} + +const struct pm8001_dispatch pm8001_8001_dispatch = { + .name = "pmc8001", + .chip_init = pm8001_chip_init, + .chip_soft_rst = pm8001_chip_soft_rst, + .chip_rst = pm8001_hw_chip_rst, + .chip_iounmap = pm8001_chip_iounmap, + .isr = pm8001_chip_isr, + .is_our_interupt = pm8001_chip_is_our_interupt, + .isr_process_oq = process_oq, + .interrupt_enable = pm8001_chip_interrupt_enable, + .interrupt_disable = pm8001_chip_interrupt_disable, + .make_prd = pm8001_chip_make_sg, + .smp_req = pm8001_chip_smp_req, + .ssp_io_req = pm8001_chip_ssp_io_req, + .sata_req = pm8001_chip_sata_req, + .phy_start_req = pm8001_chip_phy_start_req, + .phy_stop_req = pm8001_chip_phy_stop_req, + .reg_dev_req = pm8001_chip_reg_dev_req, + .dereg_dev_req = pm8001_chip_dereg_dev_req, + .phy_ctl_req = pm8001_chip_phy_ctl_req, + .task_abort = pm8001_chip_abort_task, + .ssp_tm_req = pm8001_chip_ssp_tm_req, + .get_nvmd_req = pm8001_chip_get_nvmd_req, + .set_nvmd_req = pm8001_chip_set_nvmd_req, + .fw_flash_update_req = pm8001_chip_fw_flash_update_req, + .set_dev_state_req = pm8001_chip_set_dev_state_req, +}; + |