diff options
Diffstat (limited to 'drivers/scsi/pm8001/pm8001_hwi.h')
| -rw-r--r-- | drivers/scsi/pm8001/pm8001_hwi.h | 1030 |
1 files changed, 1030 insertions, 0 deletions
diff --git a/drivers/scsi/pm8001/pm8001_hwi.h b/drivers/scsi/pm8001/pm8001_hwi.h new file mode 100644 index 00000000000..96e4daa68b8 --- /dev/null +++ b/drivers/scsi/pm8001/pm8001_hwi.h @@ -0,0 +1,1030 @@ +/* + * PMC-Sierra SPC 8001 SAS/SATA based host adapters driver + * + * Copyright (c) 2008-2009 USI Co., Ltd. + * All rights reserved. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * 1. Redistributions of source code must retain the above copyright + * notice, this list of conditions, and the following disclaimer, + * without modification. + * 2. Redistributions in binary form must reproduce at minimum a disclaimer + * substantially similar to the "NO WARRANTY" disclaimer below + * ("Disclaimer") and any redistribution must be conditioned upon + * including a substantially similar Disclaimer requirement for further + * binary redistribution. + * 3. Neither the names of the above-listed copyright holders nor the names + * of any contributors may be used to endorse or promote products derived + * from this software without specific prior written permission. + * + * Alternatively, this software may be distributed under the terms of the + * GNU General Public License ("GPL") version 2 as published by the Free + * Software Foundation. + * + * NO WARRANTY + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS + * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT + * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR + * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT + * HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS + * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) + * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, + * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING + * IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE + * POSSIBILITY OF SUCH DAMAGES. + * + */ +#ifndef _PMC8001_REG_H_ +#define _PMC8001_REG_H_ + +#include <linux/types.h> +#include <scsi/libsas.h> + + +/* for Request Opcode of IOMB */ +#define OPC_INB_ECHO 1 /* 0x000 */ +#define OPC_INB_PHYSTART 4 /* 0x004 */ +#define OPC_INB_PHYSTOP 5 /* 0x005 */ +#define OPC_INB_SSPINIIOSTART 6 /* 0x006 */ +#define OPC_INB_SSPINITMSTART 7 /* 0x007 */ +#define OPC_INB_SSPINIEXTIOSTART 8 /* 0x008 */ +#define OPC_INB_DEV_HANDLE_ACCEPT 9 /* 0x009 */ +#define OPC_INB_SSPTGTIOSTART 10 /* 0x00A */ +#define OPC_INB_SSPTGTRSPSTART 11 /* 0x00B */ +#define OPC_INB_SSPINIEDCIOSTART 12 /* 0x00C */ +#define OPC_INB_SSPINIEXTEDCIOSTART 13 /* 0x00D */ +#define OPC_INB_SSPTGTEDCIOSTART 14 /* 0x00E */ +#define OPC_INB_SSP_ABORT 15 /* 0x00F */ +#define OPC_INB_DEREG_DEV_HANDLE 16 /* 0x010 */ +#define OPC_INB_GET_DEV_HANDLE 17 /* 0x011 */ +#define OPC_INB_SMP_REQUEST 18 /* 0x012 */ +/* SMP_RESPONSE is removed */ +#define OPC_INB_SMP_RESPONSE 19 /* 0x013 */ +#define OPC_INB_SMP_ABORT 20 /* 0x014 */ +#define OPC_INB_REG_DEV 22 /* 0x016 */ +#define OPC_INB_SATA_HOST_OPSTART 23 /* 0x017 */ +#define OPC_INB_SATA_ABORT 24 /* 0x018 */ +#define OPC_INB_LOCAL_PHY_CONTROL 25 /* 0x019 */ +#define OPC_INB_GET_DEV_INFO 26 /* 0x01A */ +#define OPC_INB_FW_FLASH_UPDATE 32 /* 0x020 */ +#define OPC_INB_GPIO 34 /* 0x022 */ +#define OPC_INB_SAS_DIAG_MODE_START_END 35 /* 0x023 */ +#define OPC_INB_SAS_DIAG_EXECUTE 36 /* 0x024 */ +#define OPC_INB_SAS_HW_EVENT_ACK 37 /* 0x025 */ +#define OPC_INB_GET_TIME_STAMP 38 /* 0x026 */ +#define OPC_INB_PORT_CONTROL 39 /* 0x027 */ +#define OPC_INB_GET_NVMD_DATA 40 /* 0x028 */ +#define OPC_INB_SET_NVMD_DATA 41 /* 0x029 */ +#define OPC_INB_SET_DEVICE_STATE 42 /* 0x02A */ +#define OPC_INB_GET_DEVICE_STATE 43 /* 0x02B */ +#define OPC_INB_SET_DEV_INFO 44 /* 0x02C */ +#define OPC_INB_SAS_RE_INITIALIZE 45 /* 0x02D */ + +/* for Response Opcode of IOMB */ +#define OPC_OUB_ECHO 1 /* 0x001 */ +#define OPC_OUB_HW_EVENT 4 /* 0x004 */ +#define OPC_OUB_SSP_COMP 5 /* 0x005 */ +#define OPC_OUB_SMP_COMP 6 /* 0x006 */ +#define OPC_OUB_LOCAL_PHY_CNTRL 7 /* 0x007 */ +#define OPC_OUB_DEV_REGIST 10 /* 0x00A */ +#define OPC_OUB_DEREG_DEV 11 /* 0x00B */ +#define OPC_OUB_GET_DEV_HANDLE 12 /* 0x00C */ +#define OPC_OUB_SATA_COMP 13 /* 0x00D */ +#define OPC_OUB_SATA_EVENT 14 /* 0x00E */ +#define OPC_OUB_SSP_EVENT 15 /* 0x00F */ +#define OPC_OUB_DEV_HANDLE_ARRIV 16 /* 0x010 */ +/* SMP_RECEIVED Notification is removed */ +#define OPC_OUB_SMP_RECV_EVENT 17 /* 0x011 */ +#define OPC_OUB_SSP_RECV_EVENT 18 /* 0x012 */ +#define OPC_OUB_DEV_INFO 19 /* 0x013 */ +#define OPC_OUB_FW_FLASH_UPDATE 20 /* 0x014 */ +#define OPC_OUB_GPIO_RESPONSE 22 /* 0x016 */ +#define OPC_OUB_GPIO_EVENT 23 /* 0x017 */ +#define OPC_OUB_GENERAL_EVENT 24 /* 0x018 */ +#define OPC_OUB_SSP_ABORT_RSP 26 /* 0x01A */ +#define OPC_OUB_SATA_ABORT_RSP 27 /* 0x01B */ +#define OPC_OUB_SAS_DIAG_MODE_START_END 28 /* 0x01C */ +#define OPC_OUB_SAS_DIAG_EXECUTE 29 /* 0x01D */ +#define OPC_OUB_GET_TIME_STAMP 30 /* 0x01E */ +#define OPC_OUB_SAS_HW_EVENT_ACK 31 /* 0x01F */ +#define OPC_OUB_PORT_CONTROL 32 /* 0x020 */ +#define OPC_OUB_SKIP_ENTRY 33 /* 0x021 */ +#define OPC_OUB_SMP_ABORT_RSP 34 /* 0x022 */ +#define OPC_OUB_GET_NVMD_DATA 35 /* 0x023 */ +#define OPC_OUB_SET_NVMD_DATA 36 /* 0x024 */ +#define OPC_OUB_DEVICE_HANDLE_REMOVAL 37 /* 0x025 */ +#define OPC_OUB_SET_DEVICE_STATE 38 /* 0x026 */ +#define OPC_OUB_GET_DEVICE_STATE 39 /* 0x027 */ +#define OPC_OUB_SET_DEV_INFO 40 /* 0x028 */ +#define OPC_OUB_SAS_RE_INITIALIZE 41 /* 0x029 */ + +/* for phy start*/ +#define SPINHOLD_DISABLE (0x00 << 14) +#define SPINHOLD_ENABLE (0x01 << 14) +#define LINKMODE_SAS (0x01 << 12) +#define LINKMODE_DSATA (0x02 << 12) +#define LINKMODE_AUTO (0x03 << 12) +#define LINKRATE_15 (0x01 << 8) +#define LINKRATE_30 (0x02 << 8) +#define LINKRATE_60 (0x04 << 8) + +struct mpi_msg_hdr{ + __le32 header; /* Bits [11:0] - Message operation code */ + /* Bits [15:12] - Message Category */ + /* Bits [21:16] - Outboundqueue ID for the + operation completion message */ + /* Bits [23:22] - Reserved */ + /* Bits [28:24] - Buffer Count, indicates how + many buffer are allocated for the massage */ + /* Bits [30:29] - Reserved */ + /* Bits [31] - Message Valid bit */ +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of PHY Start Command + * use to describe enable the phy (64 bytes) + */ +struct phy_start_req { + __le32 tag; + __le32 ase_sh_lm_slr_phyid; + struct sas_identify_frame sas_identify; + u32 reserved[5]; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of PHY Start Command + * use to disable the phy (64 bytes) + */ +struct phy_stop_req { + __le32 tag; + __le32 phy_id; + u32 reserved[13]; +} __attribute__((packed, aligned(4))); + + +/* set device bits fis - device to host */ +struct set_dev_bits_fis { + u8 fis_type; /* 0xA1*/ + u8 n_i_pmport; + /* b7 : n Bit. Notification bit. If set device needs attention. */ + /* b6 : i Bit. Interrupt Bit */ + /* b5-b4: reserved2 */ + /* b3-b0: PM Port */ + u8 status; + u8 error; + u32 _r_a; +} __attribute__ ((packed)); +/* PIO setup FIS - device to host */ +struct pio_setup_fis { + u8 fis_type; /* 0x5f */ + u8 i_d_pmPort; + /* b7 : reserved */ + /* b6 : i bit. Interrupt bit */ + /* b5 : d bit. data transfer direction. set to 1 for device to host + xfer */ + /* b4 : reserved */ + /* b3-b0: PM Port */ + u8 status; + u8 error; + u8 lbal; + u8 lbam; + u8 lbah; + u8 device; + u8 lbal_exp; + u8 lbam_exp; + u8 lbah_exp; + u8 _r_a; + u8 sector_count; + u8 sector_count_exp; + u8 _r_b; + u8 e_status; + u8 _r_c[2]; + u8 transfer_count; +} __attribute__ ((packed)); + +/* + * brief the data structure of SATA Completion Response + * use to discribe the sata task response (64 bytes) + */ +struct sata_completion_resp { + __le32 tag; + __le32 status; + __le32 param; + u32 sata_resp[12]; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of SAS HW Event Notification + * use to alert the host about the hardware event(64 bytes) + */ +struct hw_event_resp { + __le32 lr_evt_status_phyid_portid; + __le32 evt_param; + __le32 npip_portstate; + struct sas_identify_frame sas_identify; + struct dev_to_host_fis sata_fis; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of REGISTER DEVICE Command + * use to describe MPI REGISTER DEVICE Command (64 bytes) + */ + +struct reg_dev_req { + __le32 tag; + __le32 phyid_portid; + __le32 dtype_dlr_retry; + __le32 firstburstsize_ITNexustimeout; + u32 sas_addr_hi; + u32 sas_addr_low; + __le32 upper_device_id; + u32 reserved[8]; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of DEREGISTER DEVICE Command + * use to request spc to remove all internal resources associated + * with the device id (64 bytes) + */ + +struct dereg_dev_req { + __le32 tag; + __le32 device_id; + u32 reserved[13]; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of DEVICE_REGISTRATION Response + * use to notify the completion of the device registration (64 bytes) + */ + +struct dev_reg_resp { + __le32 tag; + __le32 status; + __le32 device_id; + u32 reserved[12]; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of Local PHY Control Command + * use to issue PHY CONTROL to local phy (64 bytes) + */ +struct local_phy_ctl_req { + __le32 tag; + __le32 phyop_phyid; + u32 reserved1[13]; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of Local Phy Control Response + * use to describe MPI Local Phy Control Response (64 bytes) + */ +struct local_phy_ctl_resp { + __le32 tag; + __le32 phyop_phyid; + __le32 status; + u32 reserved[12]; +} __attribute__((packed, aligned(4))); + + +#define OP_BITS 0x0000FF00 +#define ID_BITS 0x0000000F + +/* + * brief the data structure of PORT Control Command + * use to control port properties (64 bytes) + */ + +struct port_ctl_req { + __le32 tag; + __le32 portop_portid; + __le32 param0; + __le32 param1; + u32 reserved1[11]; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of HW Event Ack Command + * use to acknowledge receive HW event (64 bytes) + */ + +struct hw_event_ack_req { + __le32 tag; + __le32 sea_phyid_portid; + __le32 param0; + __le32 param1; + u32 reserved1[11]; +} __attribute__((packed, aligned(4))); + + +/* + * brief the data structure of SSP Completion Response + * use to indicate a SSP Completion (n bytes) + */ +struct ssp_completion_resp { + __le32 tag; + __le32 status; + __le32 param; + __le32 ssptag_rescv_rescpad; + struct ssp_response_iu ssp_resp_iu; + __le32 residual_count; +} __attribute__((packed, aligned(4))); + + +#define SSP_RESCV_BIT 0x00010000 + +/* + * brief the data structure of SATA EVNET esponse + * use to indicate a SATA Completion (64 bytes) + */ + +struct sata_event_resp { + __le32 tag; + __le32 event; + __le32 port_id; + __le32 device_id; + u32 reserved[11]; +} __attribute__((packed, aligned(4))); + +/* + * brief the data structure of SSP EVNET esponse + * use to indicate a SSP Completion (64 bytes) + */ + +struct ssp_event_resp { + __le32 tag; + __le32 event; + __le32 port_id; + __le32 device_id; + u32 reserved[11]; +} __attribute__((packed, aligned(4))); + +/** + * brief the data structure of General Event Notification Response + * use to describe MPI General Event Notification Response (64 bytes) + */ +struct general_event_resp { + __le32 status; + __le32 inb_IOMB_payload[14]; +} __attribute__((packed, aligned(4))); + + +#define GENERAL_EVENT_PAYLOAD 14 +#define OPCODE_BITS 0x00000fff + +/* + * brief the data structure of SMP Request Command + * use to describe MPI SMP REQUEST Command (64 bytes) + */ +struct smp_req { + __le32 tag; + __le32 device_id; + __le32 len_ip_ir; + /* Bits [0] - Indirect response */ + /* Bits [1] - Indirect Payload */ + /* Bits [15:2] - Reserved */ + /* Bits [23:16] - direct payload Len */ + /* Bits [31:24] - Reserved */ + u8 smp_req16[16]; + union { + u8 smp_req[32]; + struct { + __le64 long_req_addr;/* sg dma address, LE */ + __le32 long_req_size;/* LE */ + u32 _r_a; + __le64 long_resp_addr;/* sg dma address, LE */ + __le32 long_resp_size;/* LE */ + u32 _r_b; + } long_smp_req;/* sequencer extension */ + }; +} __attribute__((packed, aligned(4))); +/* + * brief the data structure of SMP Completion Response + * use to describe MPI SMP Completion Response (64 bytes) + */ +struct smp_completion_resp { + __le32 tag; + __le32 status; + __le32 param; + __le32 _r_a[12]; +} __attribute__((packed, aligned(4))); + +/* + *brief the data structure of SSP SMP SATA Abort Command + * use to describe MPI SSP SMP & SATA Abort Command (64 bytes) + */ +struct task_abort_req { + __le32 tag; + __le32 device_id; + __le32 tag_to_abort; + __le32 abort_all; + u32 reserved[11]; +} __attribute__((packed, aligned(4))); + +/* These flags used for SSP SMP & SATA Abort */ +#define ABORT_MASK 0x3 +#define ABORT_SINGLE 0x0 +#define ABORT_ALL 0x1 + +/** + * brief the data structure of SSP SATA SMP Abort Response + * use to describe SSP SMP & SATA Abort Response ( 64 bytes) + */ +struct task_abort_resp { + __le32 tag; + __le32 status; + __le32 scp; + u32 reserved[12]; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of SAS Diagnostic Start/End Command + * use to describe MPI SAS Diagnostic Start/End Command (64 bytes) + */ +struct sas_diag_start_end_req { + __le32 tag; + __le32 operation_phyid; + u32 reserved[13]; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of SAS Diagnostic Execute Command + * use to describe MPI SAS Diagnostic Execute Command (64 bytes) + */ +struct sas_diag_execute_req{ + __le32 tag; + __le32 cmdtype_cmddesc_phyid; + __le32 pat1_pat2; + __le32 threshold; + __le32 codepat_errmsk; + __le32 pmon; + __le32 pERF1CTL; + u32 reserved[8]; +} __attribute__((packed, aligned(4))); + + +#define SAS_DIAG_PARAM_BYTES 24 + +/* + * brief the data structure of Set Device State Command + * use to describe MPI Set Device State Command (64 bytes) + */ +struct set_dev_state_req { + __le32 tag; + __le32 device_id; + __le32 nds; + u32 reserved[12]; +} __attribute__((packed, aligned(4))); + +/* + * brief the data structure of sas_re_initialization + */ +struct sas_re_initialization_req { + + __le32 tag; + __le32 SSAHOLT;/* bit29-set max port; + ** bit28-set open reject cmd retries. + ** bit27-set open reject data retries. + ** bit26-set open reject option, remap:1 or not:0. + ** bit25-set sata head of line time out. + */ + __le32 reserved_maxPorts; + __le32 open_reject_cmdretries_data_retries;/* cmd retries: 31-bit16; + * data retries: bit15-bit0. + */ + __le32 sata_hol_tmo; + u32 reserved1[10]; +} __attribute__((packed, aligned(4))); + +/* + * brief the data structure of SATA Start Command + * use to describe MPI SATA IO Start Command (64 bytes) + */ + +struct sata_start_req { + __le32 tag; + __le32 device_id; + __le32 data_len; + __le32 ncqtag_atap_dir_m; + struct host_to_dev_fis sata_fis; + u32 reserved1; + u32 reserved2; + u32 addr_low; + u32 addr_high; + __le32 len; + __le32 esgl; +} __attribute__((packed, aligned(4))); + +/** + * brief the data structure of SSP INI TM Start Command + * use to describe MPI SSP INI TM Start Command (64 bytes) + */ +struct ssp_ini_tm_start_req { + __le32 tag; + __le32 device_id; + __le32 relate_tag; + __le32 tmf; + u8 lun[8]; + __le32 ds_ads_m; + u32 reserved[8]; +} __attribute__((packed, aligned(4))); + + +struct ssp_info_unit { + u8 lun[8];/* SCSI Logical Unit Number */ + u8 reserved1;/* reserved */ + u8 efb_prio_attr; + /* B7 : enabledFirstBurst */ + /* B6-3 : taskPriority */ + /* B2-0 : taskAttribute */ + u8 reserved2; /* reserved */ + u8 additional_cdb_len; + /* B7-2 : additional_cdb_len */ + /* B1-0 : reserved */ + u8 cdb[16];/* The SCSI CDB up to 16 bytes length */ +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of SSP INI IO Start Command + * use to describe MPI SSP INI IO Start Command (64 bytes) + */ +struct ssp_ini_io_start_req { + __le32 tag; + __le32 device_id; + __le32 data_len; + __le32 dir_m_tlr; + struct ssp_info_unit ssp_iu; + __le32 addr_low; + __le32 addr_high; + __le32 len; + __le32 esgl; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of Firmware download + * use to describe MPI FW DOWNLOAD Command (64 bytes) + */ +struct fw_flash_Update_req { + __le32 tag; + __le32 cur_image_offset; + __le32 cur_image_len; + __le32 total_image_len; + u32 reserved0[7]; + __le32 sgl_addr_lo; + __le32 sgl_addr_hi; + __le32 len; + __le32 ext_reserved; +} __attribute__((packed, aligned(4))); + + +#define FWFLASH_IOMB_RESERVED_LEN 0x07 +/** + * brief the data structure of FW_FLASH_UPDATE Response + * use to describe MPI FW_FLASH_UPDATE Response (64 bytes) + * + */ +struct fw_flash_Update_resp { + dma_addr_t tag; + __le32 status; + u32 reserved[13]; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of Get NVM Data Command + * use to get data from NVM in HBA(64 bytes) + */ +struct get_nvm_data_req { + __le32 tag; + __le32 len_ir_vpdd; + __le32 vpd_offset; + u32 reserved[8]; + __le32 resp_addr_lo; + __le32 resp_addr_hi; + __le32 resp_len; + u32 reserved1; +} __attribute__((packed, aligned(4))); + + +struct set_nvm_data_req { + __le32 tag; + __le32 len_ir_vpdd; + __le32 vpd_offset; + u32 reserved[8]; + __le32 resp_addr_lo; + __le32 resp_addr_hi; + __le32 resp_len; + u32 reserved1; +} __attribute__((packed, aligned(4))); + + +#define TWI_DEVICE 0x0 +#define C_SEEPROM 0x1 +#define VPD_FLASH 0x4 +#define AAP1_RDUMP 0x5 +#define IOP_RDUMP 0x6 +#define EXPAN_ROM 0x7 + +#define IPMode 0x80000000 +#define NVMD_TYPE 0x0000000F +#define NVMD_STAT 0x0000FFFF +#define NVMD_LEN 0xFF000000 +/** + * brief the data structure of Get NVMD Data Response + * use to describe MPI Get NVMD Data Response (64 bytes) + */ +struct get_nvm_data_resp { + __le32 tag; + __le32 ir_tda_bn_dps_das_nvm; + __le32 dlen_status; + __le32 nvm_data[12]; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of SAS Diagnostic Start/End Response + * use to describe MPI SAS Diagnostic Start/End Response (64 bytes) + * + */ +struct sas_diag_start_end_resp { + __le32 tag; + __le32 status; + u32 reserved[13]; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of SAS Diagnostic Execute Response + * use to describe MPI SAS Diagnostic Execute Response (64 bytes) + * + */ +struct sas_diag_execute_resp { + __le32 tag; + __le32 cmdtype_cmddesc_phyid; + __le32 Status; + __le32 ReportData; + u32 reserved[11]; +} __attribute__((packed, aligned(4))); + + +/** + * brief the data structure of Set Device State Response + * use to describe MPI Set Device State Response (64 bytes) + * + */ +struct set_dev_state_resp { + __le32 tag; + __le32 status; + __le32 device_id; + __le32 pds_nds; + u32 reserved[11]; +} __attribute__((packed, aligned(4))); + + +#define NDS_BITS 0x0F +#define PDS_BITS 0xF0 + +/* + * HW Events type + */ + +#define HW_EVENT_RESET_START 0x01 +#define HW_EVENT_CHIP_RESET_COMPLETE 0x02 +#define HW_EVENT_PHY_STOP_STATUS 0x03 +#define HW_EVENT_SAS_PHY_UP 0x04 +#define HW_EVENT_SATA_PHY_UP 0x05 +#define HW_EVENT_SATA_SPINUP_HOLD 0x06 +#define HW_EVENT_PHY_DOWN 0x07 +#define HW_EVENT_PORT_INVALID 0x08 +#define HW_EVENT_BROADCAST_CHANGE 0x09 +#define HW_EVENT_PHY_ERROR 0x0A +#define HW_EVENT_BROADCAST_SES 0x0B +#define HW_EVENT_INBOUND_CRC_ERROR 0x0C +#define HW_EVENT_HARD_RESET_RECEIVED 0x0D +#define HW_EVENT_MALFUNCTION 0x0E +#define HW_EVENT_ID_FRAME_TIMEOUT 0x0F +#define HW_EVENT_BROADCAST_EXP 0x10 +#define HW_EVENT_PHY_START_STATUS 0x11 +#define HW_EVENT_LINK_ERR_INVALID_DWORD 0x12 +#define HW_EVENT_LINK_ERR_DISPARITY_ERROR 0x13 +#define HW_EVENT_LINK_ERR_CODE_VIOLATION 0x14 +#define HW_EVENT_LINK_ERR_LOSS_OF_DWORD_SYNCH 0x15 +#define HW_EVENT_LINK_ERR_PHY_RESET_FAILED 0x16 +#define HW_EVENT_PORT_RECOVERY_TIMER_TMO 0x17 +#define HW_EVENT_PORT_RECOVER 0x18 +#define HW_EVENT_PORT_RESET_TIMER_TMO 0x19 +#define HW_EVENT_PORT_RESET_COMPLETE 0x20 +#define EVENT_BROADCAST_ASYNCH_EVENT 0x21 + +/* port state */ +#define PORT_NOT_ESTABLISHED 0x00 +#define PORT_VALID 0x01 +#define PORT_LOSTCOMM 0x02 +#define PORT_IN_RESET 0x04 +#define PORT_INVALID 0x08 + +/* + * SSP/SMP/SATA IO Completion Status values + */ + +#define IO_SUCCESS 0x00 +#define IO_ABORTED 0x01 +#define IO_OVERFLOW 0x02 +#define IO_UNDERFLOW 0x03 +#define IO_FAILED 0x04 +#define IO_ABORT_RESET 0x05 +#define IO_NOT_VALID 0x06 +#define IO_NO_DEVICE 0x07 +#define IO_ILLEGAL_PARAMETER 0x08 +#define IO_LINK_FAILURE 0x09 +#define IO_PROG_ERROR 0x0A +#define IO_EDC_IN_ERROR 0x0B +#define IO_EDC_OUT_ERROR 0x0C +#define IO_ERROR_HW_TIMEOUT 0x0D +#define IO_XFER_ERROR_BREAK 0x0E +#define IO_XFER_ERROR_PHY_NOT_READY 0x0F +#define IO_OPEN_CNX_ERROR_PROTOCOL_NOT_SUPPORTED 0x10 +#define IO_OPEN_CNX_ERROR_ZONE_VIOLATION 0x11 +#define IO_OPEN_CNX_ERROR_BREAK 0x12 +#define IO_OPEN_CNX_ERROR_IT_NEXUS_LOSS 0x13 +#define IO_OPEN_CNX_ERROR_BAD_DESTINATION 0x14 +#define IO_OPEN_CNX_ERROR_CONNECTION_RATE_NOT_SUPPORTED 0x15 +#define IO_OPEN_CNX_ERROR_STP_RESOURCES_BUSY 0x16 +#define IO_OPEN_CNX_ERROR_WRONG_DESTINATION 0x17 +#define IO_OPEN_CNX_ERROR_UNKNOWN_ERROR 0x18 +#define IO_XFER_ERROR_NAK_RECEIVED 0x19 +#define IO_XFER_ERROR_ACK_NAK_TIMEOUT 0x1A +#define IO_XFER_ERROR_PEER_ABORTED 0x1B +#define IO_XFER_ERROR_RX_FRAME 0x1C +#define IO_XFER_ERROR_DMA 0x1D +#define IO_XFER_ERROR_CREDIT_TIMEOUT 0x1E +#define IO_XFER_ERROR_SATA_LINK_TIMEOUT 0x1F +#define IO_XFER_ERROR_SATA 0x20 +#define IO_XFER_ERROR_ABORTED_DUE_TO_SRST 0x22 +#define IO_XFER_ERROR_REJECTED_NCQ_MODE 0x21 +#define IO_XFER_ERROR_ABORTED_NCQ_MODE 0x23 +#define IO_XFER_OPEN_RETRY_TIMEOUT 0x24 +#define IO_XFER_SMP_RESP_CONNECTION_ERROR 0x25 +#define IO_XFER_ERROR_UNEXPECTED_PHASE 0x26 +#define IO_XFER_ERROR_XFER_RDY_OVERRUN 0x27 +#define IO_XFER_ERROR_XFER_RDY_NOT_EXPECTED 0x28 + +#define IO_XFER_ERROR_CMD_ISSUE_ACK_NAK_TIMEOUT 0x30 +#define IO_XFER_ERROR_CMD_ISSUE_BREAK_BEFORE_ACK_NAK 0x31 +#define IO_XFER_ERROR_CMD_ISSUE_PHY_DOWN_BEFORE_ACK_NAK 0x32 + +#define IO_XFER_ERROR_OFFSET_MISMATCH 0x34 +#define IO_XFER_ERROR_XFER_ZERO_DATA_LEN 0x35 +#define IO_XFER_CMD_FRAME_ISSUED 0x36 +#define IO_ERROR_INTERNAL_SMP_RESOURCE 0x37 +#define IO_PORT_IN_RESET 0x38 +#define IO_DS_NON_OPERATIONAL 0x39 +#define IO_DS_IN_RECOVERY 0x3A +#define IO_TM_TAG_NOT_FOUND 0x3B +#define IO_XFER_PIO_SETUP_ERROR 0x3C +#define IO_SSP_EXT_IU_ZERO_LEN_ERROR 0x3D +#define IO_DS_IN_ERROR 0x3E +#define IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY 0x3F +#define IO_ABORT_IN_PROGRESS 0x40 +#define IO_ABORT_DELAYED 0x41 +#define IO_INVALID_LENGTH 0x42 + +/* WARNING: This error code must always be the last number. + * If you add error code, modify this code also + * It is used as an index + */ +#define IO_ERROR_UNKNOWN_GENERIC 0x43 + +/* MSGU CONFIGURATION TABLE*/ + +#define SPC_MSGU_CFG_TABLE_UPDATE 0x01/* Inbound doorbell bit0 */ +#define SPC_MSGU_CFG_TABLE_RESET 0x02/* Inbound doorbell bit1 */ +#define SPC_MSGU_CFG_TABLE_FREEZE 0x04/* Inbound doorbell bit2 */ +#define SPC_MSGU_CFG_TABLE_UNFREEZE 0x08/* Inbound doorbell bit4 */ +#define MSGU_IBDB_SET 0x04 +#define MSGU_HOST_INT_STATUS 0x08 +#define MSGU_HOST_INT_MASK 0x0C +#define MSGU_IOPIB_INT_STATUS 0x18 +#define MSGU_IOPIB_INT_MASK 0x1C +#define MSGU_IBDB_CLEAR 0x20/* RevB - Host not use */ +#define MSGU_MSGU_CONTROL 0x24 +#define MSGU_ODR 0x3C/* RevB */ +#define MSGU_ODCR 0x40/* RevB */ +#define MSGU_SCRATCH_PAD_0 0x44 +#define MSGU_SCRATCH_PAD_1 0x48 +#define MSGU_SCRATCH_PAD_2 0x4C +#define MSGU_SCRATCH_PAD_3 0x50 +#define MSGU_HOST_SCRATCH_PAD_0 0x54 +#define MSGU_HOST_SCRATCH_PAD_1 0x58 +#define MSGU_HOST_SCRATCH_PAD_2 0x5C +#define MSGU_HOST_SCRATCH_PAD_3 0x60 +#define MSGU_HOST_SCRATCH_PAD_4 0x64 +#define MSGU_HOST_SCRATCH_PAD_5 0x68 +#define MSGU_HOST_SCRATCH_PAD_6 0x6C +#define MSGU_HOST_SCRATCH_PAD_7 0x70 +#define MSGU_ODMR 0x74/* RevB */ + +/* bit definition for ODMR register */ +#define ODMR_MASK_ALL 0xFFFFFFFF/* mask all + interrupt vector */ +#define ODMR_CLEAR_ALL 0/* clear all + interrupt vector */ +/* bit definition for ODCR register */ +#define ODCR_CLEAR_ALL 0xFFFFFFFF /* mask all + interrupt vector*/ +/* MSIX Interupts */ +#define MSIX_TABLE_OFFSET 0x2000 +#define MSIX_TABLE_ELEMENT_SIZE 0x10 +#define MSIX_INTERRUPT_CONTROL_OFFSET 0xC +#define MSIX_TABLE_BASE (MSIX_TABLE_OFFSET + MSIX_INTERRUPT_CONTROL_OFFSET) +#define MSIX_INTERRUPT_DISABLE 0x1 +#define MSIX_INTERRUPT_ENABLE 0x0 + + +/* state definition for Scratch Pad1 register */ +#define SCRATCH_PAD1_POR 0x00 /* power on reset state */ +#define SCRATCH_PAD1_SFR 0x01 /* soft reset state */ +#define SCRATCH_PAD1_ERR 0x02 /* error state */ +#define SCRATCH_PAD1_RDY 0x03 /* ready state */ +#define SCRATCH_PAD1_RST 0x04 /* soft reset toggle flag */ +#define SCRATCH_PAD1_AAP1RDY_RST 0x08 /* AAP1 ready for soft reset */ +#define SCRATCH_PAD1_STATE_MASK 0xFFFFFFF0 /* ScratchPad1 + Mask, bit1-0 State, bit2 Soft Reset, bit3 FW RDY for Soft Reset */ +#define SCRATCH_PAD1_RESERVED 0x000003F8 /* Scratch Pad1 + Reserved bit 3 to 9 */ + + /* state definition for Scratch Pad2 register */ +#define SCRATCH_PAD2_POR 0x00 /* power on state */ +#define SCRATCH_PAD2_SFR 0x01 /* soft reset state */ +#define SCRATCH_PAD2_ERR 0x02 /* error state */ +#define SCRATCH_PAD2_RDY 0x03 /* ready state */ +#define SCRATCH_PAD2_FWRDY_RST 0x04 /* FW ready for soft reset flag*/ +#define SCRATCH_PAD2_IOPRDY_RST 0x08 /* IOP ready for soft reset */ +#define SCRATCH_PAD2_STATE_MASK 0xFFFFFFF4 /* ScratchPad 2 + Mask, bit1-0 State */ +#define SCRATCH_PAD2_RESERVED 0x000003FC /* Scratch Pad1 + Reserved bit 2 to 9 */ + +#define SCRATCH_PAD_ERROR_MASK 0xFFFFFC00 /* Error mask bits */ +#define SCRATCH_PAD_STATE_MASK 0x00000003 /* State Mask bits */ + +/* main configuration offset - byte offset */ +#define MAIN_SIGNATURE_OFFSET 0x00/* DWORD 0x00 */ +#define MAIN_INTERFACE_REVISION 0x04/* DWORD 0x01 */ +#define MAIN_FW_REVISION 0x08/* DWORD 0x02 */ +#define MAIN_MAX_OUTSTANDING_IO_OFFSET 0x0C/* DWORD 0x03 */ +#define MAIN_MAX_SGL_OFFSET 0x10/* DWORD 0x04 */ +#define MAIN_CNTRL_CAP_OFFSET 0x14/* DWORD 0x05 */ +#define MAIN_GST_OFFSET 0x18/* DWORD 0x06 */ +#define MAIN_IBQ_OFFSET 0x1C/* DWORD 0x07 */ +#define MAIN_OBQ_OFFSET 0x20/* DWORD 0x08 */ +#define MAIN_IQNPPD_HPPD_OFFSET 0x24/* DWORD 0x09 */ +#define MAIN_OB_HW_EVENT_PID03_OFFSET 0x28/* DWORD 0x0A */ +#define MAIN_OB_HW_EVENT_PID47_OFFSET 0x2C/* DWORD 0x0B */ +#define MAIN_OB_NCQ_EVENT_PID03_OFFSET 0x30/* DWORD 0x0C */ +#define MAIN_OB_NCQ_EVENT_PID47_OFFSET 0x34/* DWORD 0x0D */ +#define MAIN_TITNX_EVENT_PID03_OFFSET 0x38/* DWORD 0x0E */ +#define MAIN_TITNX_EVENT_PID47_OFFSET 0x3C/* DWORD 0x0F */ +#define MAIN_OB_SSP_EVENT_PID03_OFFSET 0x40/* DWORD 0x10 */ +#define MAIN_OB_SSP_EVENT_PID47_OFFSET 0x44/* DWORD 0x11 */ +#define MAIN_OB_SMP_EVENT_PID03_OFFSET 0x48/* DWORD 0x12 */ +#define MAIN_OB_SMP_EVENT_PID47_OFFSET 0x4C/* DWORD 0x13 */ +#define MAIN_EVENT_LOG_ADDR_HI 0x50/* DWORD 0x14 */ +#define MAIN_EVENT_LOG_ADDR_LO 0x54/* DWORD 0x15 */ +#define MAIN_EVENT_LOG_BUFF_SIZE 0x58/* DWORD 0x16 */ +#define MAIN_EVENT_LOG_OPTION 0x5C/* DWORD 0x17 */ +#define MAIN_IOP_EVENT_LOG_ADDR_HI 0x60/* DWORD 0x18 */ +#define MAIN_IOP_EVENT_LOG_ADDR_LO 0x64/* DWORD 0x19 */ +#define MAIN_IOP_EVENT_LOG_BUFF_SIZE 0x68/* DWORD 0x1A */ +#define MAIN_IOP_EVENT_LOG_OPTION 0x6C/* DWORD 0x1B */ +#define MAIN_FATAL_ERROR_INTERRUPT 0x70/* DWORD 0x1C */ +#define MAIN_FATAL_ERROR_RDUMP0_OFFSET 0x74/* DWORD 0x1D */ +#define MAIN_FATAL_ERROR_RDUMP0_LENGTH 0x78/* DWORD 0x1E */ +#define MAIN_FATAL_ERROR_RDUMP1_OFFSET 0x7C/* DWORD 0x1F */ +#define MAIN_FATAL_ERROR_RDUMP1_LENGTH 0x80/* DWORD 0x20 */ +#define MAIN_HDA_FLAGS_OFFSET 0x84/* DWORD 0x21 */ +#define MAIN_ANALOG_SETUP_OFFSET 0x88/* DWORD 0x22 */ + +/* Gereral Status Table offset - byte offset */ +#define GST_GSTLEN_MPIS_OFFSET 0x00 +#define GST_IQ_FREEZE_STATE0_OFFSET 0x04 +#define GST_IQ_FREEZE_STATE1_OFFSET 0x08 +#define GST_MSGUTCNT_OFFSET 0x0C +#define GST_IOPTCNT_OFFSET 0x10 +#define GST_PHYSTATE_OFFSET 0x18 +#define GST_PHYSTATE0_OFFSET 0x18 +#define GST_PHYSTATE1_OFFSET 0x1C +#define GST_PHYSTATE2_OFFSET 0x20 +#define GST_PHYSTATE3_OFFSET 0x24 +#define GST_PHYSTATE4_OFFSET 0x28 +#define GST_PHYSTATE5_OFFSET 0x2C +#define GST_PHYSTATE6_OFFSET 0x30 +#define GST_PHYSTATE7_OFFSET 0x34 +#define GST_RERRINFO_OFFSET 0x44 + +/* General Status Table - MPI state */ +#define GST_MPI_STATE_UNINIT 0x00 +#define GST_MPI_STATE_INIT 0x01 +#define GST_MPI_STATE_TERMINATION 0x02 +#define GST_MPI_STATE_ERROR 0x03 +#define GST_MPI_STATE_MASK 0x07 + +#define MBIC_NMI_ENABLE_VPE0_IOP 0x000418 +#define MBIC_NMI_ENABLE_VPE0_AAP1 0x000418 +/* PCIE registers - BAR2(0x18), BAR1(win) 0x010000 */ +#define PCIE_EVENT_INTERRUPT_ENABLE 0x003040 +#define PCIE_EVENT_INTERRUPT 0x003044 +#define PCIE_ERROR_INTERRUPT_ENABLE 0x003048 +#define PCIE_ERROR_INTERRUPT 0x00304C +/* signature defintion for host scratch pad0 register */ +#define SPC_SOFT_RESET_SIGNATURE 0x252acbcd +/* Signature for Soft Reset */ + +/* SPC Reset register - BAR4(0x20), BAR2(win) (need dynamic mapping) */ +#define SPC_REG_RESET 0x000000/* reset register */ + +/* bit difination for SPC_RESET register */ +#define SPC_REG_RESET_OSSP 0x00000001 +#define SPC_REG_RESET_RAAE 0x00000002 +#define SPC_REG_RESET_PCS_SPBC 0x00000004 +#define SPC_REG_RESET_PCS_IOP_SS 0x00000008 +#define SPC_REG_RESET_PCS_AAP1_SS 0x00000010 +#define SPC_REG_RESET_PCS_AAP2_SS 0x00000020 +#define SPC_REG_RESET_PCS_LM 0x00000040 +#define SPC_REG_RESET_PCS 0x00000080 +#define SPC_REG_RESET_GSM 0x00000100 +#define SPC_REG_RESET_DDR2 0x00010000 +#define SPC_REG_RESET_BDMA_CORE 0x00020000 +#define SPC_REG_RESET_BDMA_SXCBI 0x00040000 +#define SPC_REG_RESET_PCIE_AL_SXCBI 0x00080000 +#define SPC_REG_RESET_PCIE_PWR 0x00100000 +#define SPC_REG_RESET_PCIE_SFT 0x00200000 +#define SPC_REG_RESET_PCS_SXCBI 0x00400000 +#define SPC_REG_RESET_LMS_SXCBI 0x00800000 +#define SPC_REG_RESET_PMIC_SXCBI 0x01000000 +#define SPC_REG_RESET_PMIC_CORE 0x02000000 +#define SPC_REG_RESET_PCIE_PC_SXCBI 0x04000000 +#define SPC_REG_RESET_DEVICE 0x80000000 + +/* registers for BAR Shifting - BAR2(0x18), BAR1(win) */ +#define SPC_IBW_AXI_TRANSLATION_LOW 0x003258 + +#define MBIC_AAP1_ADDR_BASE 0x060000 +#define MBIC_IOP_ADDR_BASE 0x070000 +#define GSM_ADDR_BASE 0x0700000 +/* Dynamic map through Bar4 - 0x00700000 */ +#define GSM_CONFIG_RESET 0x00000000 +#define RAM_ECC_DB_ERR 0x00000018 +#define GSM_READ_ADDR_PARITY_INDIC 0x00000058 +#define GSM_WRITE_ADDR_PARITY_INDIC 0x00000060 +#define GSM_WRITE_DATA_PARITY_INDIC 0x00000068 +#define GSM_READ_ADDR_PARITY_CHECK 0x00000038 +#define GSM_WRITE_ADDR_PARITY_CHECK 0x00000040 +#define GSM_WRITE_DATA_PARITY_CHECK 0x00000048 + +#define RB6_ACCESS_REG 0x6A0000 +#define HDAC_EXEC_CMD 0x0002 +#define HDA_C_PA 0xcb +#define HDA_SEQ_ID_BITS 0x00ff0000 +#define HDA_GSM_OFFSET_BITS 0x00FFFFFF +#define MBIC_AAP1_ADDR_BASE 0x060000 +#define MBIC_IOP_ADDR_BASE 0x070000 +#define GSM_ADDR_BASE 0x0700000 +#define SPC_TOP_LEVEL_ADDR_BASE 0x000000 +#define GSM_CONFIG_RESET_VALUE 0x00003b00 +#define GPIO_ADDR_BASE 0x00090000 +#define GPIO_GPIO_0_0UTPUT_CTL_OFFSET 0x0000010c + +/* RB6 offset */ +#define SPC_RB6_OFFSET 0x80C0 +/* Magic number of soft reset for RB6 */ +#define RB6_MAGIC_NUMBER_RST 0x1234 + +/* Device Register status */ +#define DEVREG_SUCCESS 0x00 +#define DEVREG_FAILURE_OUT_OF_RESOURCE 0x01 +#define DEVREG_FAILURE_DEVICE_ALREADY_REGISTERED 0x02 +#define DEVREG_FAILURE_INVALID_PHY_ID 0x03 +#define DEVREG_FAILURE_PHY_ID_ALREADY_REGISTERED 0x04 +#define DEVREG_FAILURE_PORT_ID_OUT_OF_RANGE 0x05 +#define DEVREG_FAILURE_PORT_NOT_VALID_STATE 0x06 +#define DEVREG_FAILURE_DEVICE_TYPE_NOT_VALID 0x07 + +#endif + |