diff options
Diffstat (limited to 'drivers/scsi/qla4xxx/ql4_os.c')
| -rw-r--r-- | drivers/scsi/qla4xxx/ql4_os.c | 315 |
1 files changed, 311 insertions, 4 deletions
diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index 5529b2a3974..370d40ff152 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -163,10 +163,10 @@ static void qla4xxx_recovery_timedout(struct iscsi_cls_session *session) if (atomic_read(&ddb_entry->state) != DDB_STATE_ONLINE) { atomic_set(&ddb_entry->state, DDB_STATE_DEAD); - DEBUG2(printk("scsi%ld: %s: ddb [%d] port down retry count " + DEBUG2(printk("scsi%ld: %s: ddb [%d] session recovery timeout " "of (%d) secs exhausted, marking device DEAD.\n", ha->host_no, __func__, ddb_entry->fw_ddb_index, - ha->port_down_retry_count)); + QL4_SESS_RECOVERY_TMO)); qla4xxx_wake_dpc(ha); } @@ -298,7 +298,8 @@ int qla4xxx_add_sess(struct ddb_entry *ddb_entry) { int err; - ddb_entry->sess->recovery_tmo = ddb_entry->ha->port_down_retry_count; + ddb_entry->sess->recovery_tmo = QL4_SESS_RECOVERY_TMO; + err = iscsi_add_session(ddb_entry->sess, ddb_entry->fw_ddb_index); if (err) { DEBUG2(printk(KERN_ERR "Could not add session.\n")); @@ -474,6 +475,14 @@ static int qla4xxx_queuecommand(struct scsi_cmnd *cmd, struct srb *srb; int rval; + if (test_bit(AF_EEH_BUSY, &ha->flags)) { + if (test_bit(AF_PCI_CHANNEL_IO_PERM_FAILURE, &ha->flags)) + cmd->result = DID_NO_CONNECT << 16; + else + cmd->result = DID_REQUEUE << 16; + goto qc_fail_command; + } + if (!sess) { cmd->result = DID_IMM_RETRY << 16; goto qc_fail_command; @@ -654,6 +663,13 @@ static void qla4_8xxx_check_fw_alive(struct scsi_qla_host *ha) uint32_t fw_heartbeat_counter, halt_status; fw_heartbeat_counter = qla4_8xxx_rd_32(ha, QLA82XX_PEG_ALIVE_COUNTER); + /* If PEG_ALIVE_COUNTER is 0xffffffff, AER/EEH is in progress, ignore */ + if (fw_heartbeat_counter == 0xffffffff) { + DEBUG2(printk(KERN_WARNING "scsi%ld: %s: Device in frozen " + "state, QLA82XX_PEG_ALIVE_COUNTER is 0xffffffff\n", + ha->host_no, __func__)); + return; + } if (ha->fw_heartbeat_counter == fw_heartbeat_counter) { ha->seconds_since_last_heartbeat++; @@ -662,6 +678,7 @@ static void qla4_8xxx_check_fw_alive(struct scsi_qla_host *ha) ha->seconds_since_last_heartbeat = 0; halt_status = qla4_8xxx_rd_32(ha, QLA82XX_PEG_HALT_STATUS1); + /* Since we cannot change dev_state in interrupt * context, set appropriate DPC flag then wakeup * DPC */ @@ -673,6 +690,7 @@ static void qla4_8xxx_check_fw_alive(struct scsi_qla_host *ha) set_bit(DPC_RESET_HA, &ha->dpc_flags); } qla4xxx_wake_dpc(ha); + qla4xxx_mailbox_premature_completion(ha); } } ha->fw_heartbeat_counter = fw_heartbeat_counter; @@ -698,6 +716,7 @@ void qla4_8xxx_watchdog(struct scsi_qla_host *ha) ha->host_no, __func__); set_bit(DPC_RESET_HA, &ha->dpc_flags); qla4xxx_wake_dpc(ha); + qla4xxx_mailbox_premature_completion(ha); } else if (dev_state == QLA82XX_DEV_NEED_QUIESCENT && !test_bit(DPC_HA_NEED_QUIESCENT, &ha->dpc_flags)) { printk("scsi%ld: %s: HW State: NEED QUIES!\n", @@ -719,6 +738,19 @@ static void qla4xxx_timer(struct scsi_qla_host *ha) { struct ddb_entry *ddb_entry, *dtemp; int start_dpc = 0; + uint16_t w; + + /* If we are in the middle of AER/EEH processing + * skip any processing and reschedule the timer + */ + if (test_bit(AF_EEH_BUSY, &ha->flags)) { + mod_timer(&ha->timer, jiffies + HZ); + return; + } + + /* Hardware read to trigger an EEH error during mailbox waits. */ + if (!pci_channel_offline(ha->pdev)) + pci_read_config_word(ha->pdev, PCI_VENDOR_ID, &w); if (test_bit(AF_HBA_GOING_AWAY, &ha->flags)) { DEBUG2(ql4_printk(KERN_INFO, ha, "%s exited. HBA GOING AWAY\n", @@ -1207,7 +1239,13 @@ static void qla4xxx_do_dpc(struct work_struct *work) /* Initialization not yet finished. Don't do anything yet. */ if (!test_bit(AF_INIT_DONE, &ha->flags)) - return; + goto do_dpc_exit; + + if (test_bit(AF_EEH_BUSY, &ha->flags)) { + DEBUG2(printk(KERN_INFO "scsi%ld: %s: flags = %lx\n", + ha->host_no, __func__, ha->flags)); + goto do_dpc_exit; + } /* HBA is in the process of being permanently disabled. * Don't process anything */ @@ -1346,6 +1384,8 @@ dpc_post_reset_ha: } } } + +do_dpc_exit: clear_bit(AF_DPC_SCHEDULED, &ha->flags); } @@ -1612,6 +1652,8 @@ static int __devinit qla4xxx_probe_adapter(struct pci_dev *pdev, ha->host = host; ha->host_no = host->host_no; + pci_enable_pcie_error_reporting(pdev); + /* Setup Runtime configurable options */ if (is_qla8022(ha)) { ha->isp_ops = &qla4_8xxx_isp_ops; @@ -1630,6 +1672,10 @@ static int __devinit qla4xxx_probe_adapter(struct pci_dev *pdev, ha->isp_ops = &qla4xxx_isp_ops; } + /* Set EEH reset type to fundamental if required by hba */ + if (is_qla8022(ha)) + pdev->needs_freset = 1; + /* Configure PCI I/O space. */ ret = ha->isp_ops->iospace_config(ha); if (ret) @@ -1726,6 +1772,7 @@ static int __devinit qla4xxx_probe_adapter(struct pci_dev *pdev, } } + pci_save_state(ha->pdev); ha->isp_ops->enable_intrs(ha); /* Start timer thread. */ @@ -1752,6 +1799,7 @@ probe_failed: qla4xxx_free_adapter(ha); probe_failed_ioconfig: + pci_disable_pcie_error_reporting(pdev); scsi_host_put(ha->host); probe_disable_device: @@ -1781,6 +1829,7 @@ static void __devexit qla4xxx_remove_adapter(struct pci_dev *pdev) scsi_host_put(ha->host); + pci_disable_pcie_error_reporting(pdev); pci_disable_device(pdev); pci_set_drvdata(pdev, NULL); } @@ -1877,6 +1926,17 @@ static int qla4xxx_eh_wait_on_command(struct scsi_qla_host *ha, int done = 0; struct srb *rp; uint32_t max_wait_time = EH_WAIT_CMD_TOV; + int ret = SUCCESS; + + /* Dont wait on command if PCI error is being handled + * by PCI AER driver + */ + if (unlikely(pci_channel_offline(ha->pdev)) || + (test_bit(AF_EEH_BUSY, &ha->flags))) { + ql4_printk(KERN_WARNING, ha, "scsi%ld: Return from %s\n", + ha->host_no, __func__); + return ret; + } do { /* Checking to see if its returned to OS */ @@ -2172,6 +2232,252 @@ static int qla4xxx_eh_host_reset(struct scsi_cmnd *cmd) return return_status; } +/* PCI AER driver recovers from all correctable errors w/o + * driver intervention. For uncorrectable errors PCI AER + * driver calls the following device driver's callbacks + * + * - Fatal Errors - link_reset + * - Non-Fatal Errors - driver's pci_error_detected() which + * returns CAN_RECOVER, NEED_RESET or DISCONNECT. + * + * PCI AER driver calls + * CAN_RECOVER - driver's pci_mmio_enabled(), mmio_enabled + * returns RECOVERED or NEED_RESET if fw_hung + * NEED_RESET - driver's slot_reset() + * DISCONNECT - device is dead & cannot recover + * RECOVERED - driver's pci_resume() + */ +static pci_ers_result_t +qla4xxx_pci_error_detected(struct pci_dev *pdev, pci_channel_state_t state) +{ + struct scsi_qla_host *ha = pci_get_drvdata(pdev); + + ql4_printk(KERN_WARNING, ha, "scsi%ld: %s: error detected:state %x\n", + ha->host_no, __func__, state); + + if (!is_aer_supported(ha)) + return PCI_ERS_RESULT_NONE; + + switch (state) { + case pci_channel_io_normal: + clear_bit(AF_EEH_BUSY, &ha->flags); + return PCI_ERS_RESULT_CAN_RECOVER; + case pci_channel_io_frozen: + set_bit(AF_EEH_BUSY, &ha->flags); + qla4xxx_mailbox_premature_completion(ha); + qla4xxx_free_irqs(ha); + pci_disable_device(pdev); + return PCI_ERS_RESULT_NEED_RESET; + case pci_channel_io_perm_failure: + set_bit(AF_EEH_BUSY, &ha->flags); + set_bit(AF_PCI_CHANNEL_IO_PERM_FAILURE, &ha->flags); + qla4xxx_abort_active_cmds(ha, DID_NO_CONNECT << 16); + return PCI_ERS_RESULT_DISCONNECT; + } + return PCI_ERS_RESULT_NEED_RESET; +} + +/** + * qla4xxx_pci_mmio_enabled() gets called if + * qla4xxx_pci_error_detected() returns PCI_ERS_RESULT_CAN_RECOVER + * and read/write to the device still works. + **/ +static pci_ers_result_t +qla4xxx_pci_mmio_enabled(struct pci_dev *pdev) +{ + struct scsi_qla_host *ha = pci_get_drvdata(pdev); + + if (!is_aer_supported(ha)) + return PCI_ERS_RESULT_NONE; + + if (test_bit(AF_FW_RECOVERY, &ha->flags)) { + ql4_printk(KERN_WARNING, ha, "scsi%ld: %s: firmware hang -- " + "mmio_enabled\n", ha->host_no, __func__); + return PCI_ERS_RESULT_NEED_RESET; + } else + return PCI_ERS_RESULT_RECOVERED; +} + +uint32_t qla4_8xxx_error_recovery(struct scsi_qla_host *ha) +{ + uint32_t rval = QLA_ERROR; + int fn; + struct pci_dev *other_pdev = NULL; + + ql4_printk(KERN_WARNING, ha, "scsi%ld: In %s\n", ha->host_no, __func__); + + set_bit(DPC_RESET_ACTIVE, &ha->dpc_flags); + + if (test_bit(AF_ONLINE, &ha->flags)) { + clear_bit(AF_ONLINE, &ha->flags); + qla4xxx_mark_all_devices_missing(ha); + qla4xxx_process_aen(ha, FLUSH_DDB_CHANGED_AENS); + qla4xxx_abort_active_cmds(ha, DID_RESET << 16); + } + + fn = PCI_FUNC(ha->pdev->devfn); + while (fn > 0) { + fn--; + ql4_printk(KERN_INFO, ha, "scsi%ld: %s: Finding PCI device at " + "func %x\n", ha->host_no, __func__, fn); + /* Get the pci device given the domain, bus, + * slot/function number */ + other_pdev = + pci_get_domain_bus_and_slot(pci_domain_nr(ha->pdev->bus), + ha->pdev->bus->number, PCI_DEVFN(PCI_SLOT(ha->pdev->devfn), + fn)); + + if (!other_pdev) + continue; + + if (atomic_read(&other_pdev->enable_cnt)) { + ql4_printk(KERN_INFO, ha, "scsi%ld: %s: Found PCI " + "func in enabled state%x\n", ha->host_no, + __func__, fn); + pci_dev_put(other_pdev); + break; + } + pci_dev_put(other_pdev); + } + + /* The first function on the card, the reset owner will + * start & initialize the firmware. The other functions + * on the card will reset the firmware context + */ + if (!fn) { + ql4_printk(KERN_INFO, ha, "scsi%ld: %s: devfn being reset " + "0x%x is the owner\n", ha->host_no, __func__, + ha->pdev->devfn); + + qla4_8xxx_idc_lock(ha); + qla4_8xxx_wr_32(ha, QLA82XX_CRB_DEV_STATE, + QLA82XX_DEV_COLD); + + qla4_8xxx_wr_32(ha, QLA82XX_CRB_DRV_IDC_VERSION, + QLA82XX_IDC_VERSION); + + qla4_8xxx_idc_unlock(ha); + clear_bit(AF_FW_RECOVERY, &ha->flags); + rval = qla4xxx_initialize_adapter(ha, PRESERVE_DDB_LIST); + qla4_8xxx_idc_lock(ha); + + if (rval != QLA_SUCCESS) { + ql4_printk(KERN_INFO, ha, "scsi%ld: %s: HW State: " + "FAILED\n", ha->host_no, __func__); + qla4_8xxx_clear_drv_active(ha); + qla4_8xxx_wr_32(ha, QLA82XX_CRB_DEV_STATE, + QLA82XX_DEV_FAILED); + } else { + ql4_printk(KERN_INFO, ha, "scsi%ld: %s: HW State: " + "READY\n", ha->host_no, __func__); + qla4_8xxx_wr_32(ha, QLA82XX_CRB_DEV_STATE, + QLA82XX_DEV_READY); + /* Clear driver state register */ + qla4_8xxx_wr_32(ha, QLA82XX_CRB_DRV_STATE, 0); + qla4_8xxx_set_drv_active(ha); + ha->isp_ops->enable_intrs(ha); + } + qla4_8xxx_idc_unlock(ha); + } else { + ql4_printk(KERN_INFO, ha, "scsi%ld: %s: devfn 0x%x is not " + "the reset owner\n", ha->host_no, __func__, + ha->pdev->devfn); + if ((qla4_8xxx_rd_32(ha, QLA82XX_CRB_DEV_STATE) == + QLA82XX_DEV_READY)) { + clear_bit(AF_FW_RECOVERY, &ha->flags); + rval = qla4xxx_initialize_adapter(ha, + PRESERVE_DDB_LIST); + if (rval == QLA_SUCCESS) + ha->isp_ops->enable_intrs(ha); + qla4_8xxx_idc_lock(ha); + qla4_8xxx_set_drv_active(ha); + qla4_8xxx_idc_unlock(ha); + } + } + clear_bit(DPC_RESET_ACTIVE, &ha->dpc_flags); + return rval; +} + +static pci_ers_result_t +qla4xxx_pci_slot_reset(struct pci_dev *pdev) +{ + pci_ers_result_t ret = PCI_ERS_RESULT_DISCONNECT; + struct scsi_qla_host *ha = pci_get_drvdata(pdev); + int rc; + + ql4_printk(KERN_WARNING, ha, "scsi%ld: %s: slot_reset\n", + ha->host_no, __func__); + + if (!is_aer_supported(ha)) + return PCI_ERS_RESULT_NONE; + + /* Restore the saved state of PCIe device - + * BAR registers, PCI Config space, PCIX, MSI, + * IOV states + */ + pci_restore_state(pdev); + + /* pci_restore_state() clears the saved_state flag of the device + * save restored state which resets saved_state flag + */ + pci_save_state(pdev); + + /* Initialize device or resume if in suspended state */ + rc = pci_enable_device(pdev); + if (rc) { + ql4_printk(KERN_WARNING, ha, "scsi%ld: %s: Cant re-enable " + "device after reset\n", ha->host_no, __func__); + goto exit_slot_reset; + } + + ret = qla4xxx_request_irqs(ha); + if (ret) { + ql4_printk(KERN_WARNING, ha, "Failed to reserve interrupt %d" + " already in use.\n", pdev->irq); + goto exit_slot_reset; + } + + if (is_qla8022(ha)) { + if (qla4_8xxx_error_recovery(ha) == QLA_SUCCESS) { + ret = PCI_ERS_RESULT_RECOVERED; + goto exit_slot_reset; + } else + goto exit_slot_reset; + } + +exit_slot_reset: + ql4_printk(KERN_WARNING, ha, "scsi%ld: %s: Return=%x\n" + "device after reset\n", ha->host_no, __func__, ret); + return ret; +} + +static void +qla4xxx_pci_resume(struct pci_dev *pdev) +{ + struct scsi_qla_host *ha = pci_get_drvdata(pdev); + int ret; + + ql4_printk(KERN_WARNING, ha, "scsi%ld: %s: pci_resume\n", + ha->host_no, __func__); + + ret = qla4xxx_wait_for_hba_online(ha); + if (ret != QLA_SUCCESS) { + ql4_printk(KERN_ERR, ha, "scsi%ld: %s: the device failed to " + "resume I/O from slot/link_reset\n", ha->host_no, + __func__); + } + + pci_cleanup_aer_uncorrect_error_status(pdev); + clear_bit(AF_EEH_BUSY, &ha->flags); +} + +static struct pci_error_handlers qla4xxx_err_handler = { + .error_detected = qla4xxx_pci_error_detected, + .mmio_enabled = qla4xxx_pci_mmio_enabled, + .slot_reset = qla4xxx_pci_slot_reset, + .resume = qla4xxx_pci_resume, +}; + static struct pci_device_id qla4xxx_pci_tbl[] = { { .vendor = PCI_VENDOR_ID_QLOGIC, @@ -2206,6 +2512,7 @@ static struct pci_driver qla4xxx_pci_driver = { .id_table = qla4xxx_pci_tbl, .probe = qla4xxx_probe_adapter, .remove = qla4xxx_remove_adapter, + .err_handler = &qla4xxx_err_handler, }; static int __init qla4xxx_module_init(void) |