diff options
Diffstat (limited to 'drivers/scsi/tmscsim.h')
| -rw-r--r-- | drivers/scsi/tmscsim.h | 551 |
1 files changed, 0 insertions, 551 deletions
diff --git a/drivers/scsi/tmscsim.h b/drivers/scsi/tmscsim.h deleted file mode 100644 index 3d1bb4ad182..00000000000 --- a/drivers/scsi/tmscsim.h +++ /dev/null @@ -1,551 +0,0 @@ -/*********************************************************************** -;* File Name : TMSCSIM.H * -;* TEKRAM DC-390(T) PCI SCSI Bus Master Host Adapter * -;* Device Driver * -;***********************************************************************/ -/* $Id: tmscsim.h,v 2.15.2.3 2000/11/17 20:52:27 garloff Exp $ */ - -#ifndef _TMSCSIM_H -#define _TMSCSIM_H - -#include <linux/types.h> - -#define SCSI_IRQ_NONE 255 - -#define MAX_ADAPTER_NUM 4 -#define MAX_SG_LIST_BUF 16 /* Not used */ -#define MAX_SCSI_ID 8 -#define MAX_SRB_CNT 50 /* Max number of started commands */ - -#define SEL_TIMEOUT 153 /* 250 ms selection timeout (@ 40 MHz) */ - -/* -;----------------------------------------------------------------------- -; SCSI Request Block -;----------------------------------------------------------------------- -*/ -struct dc390_srb -{ -//u8 CmdBlock[12]; - -struct dc390_srb *pNextSRB; -struct dc390_dcb *pSRBDCB; -struct scsi_cmnd *pcmd; -struct scatterlist *pSegmentList; - -struct scatterlist Segmentx; /* make a one entry of S/G list table */ - -unsigned long SGBusAddr; /*;a segment starting address as seen by AM53C974A - in CPU endianness. We're only getting 32-bit bus - addresses by default */ -unsigned long SGToBeXferLen; /*; to be xfer length */ -unsigned long TotalXferredLen; -unsigned long SavedTotXLen; -unsigned long Saved_Ptr; -u32 SRBState; - -u8 SRBStatus; -u8 SRBFlag; /*; b0-AutoReqSense,b6-Read,b7-write */ - /*; b4-settimeout,b5-Residual valid */ -u8 AdaptStatus; -u8 TargetStatus; - -u8 ScsiPhase; -s8 TagNumber; -u8 SGIndex; -u8 SGcount; - -u8 MsgCnt; -u8 EndMessage; - -u8 MsgInBuf[6]; -u8 MsgOutBuf[6]; - -//u8 IORBFlag; /*;81h-Reset, 2-retry */ -}; - - -/* -;----------------------------------------------------------------------- -; Device Control Block -;----------------------------------------------------------------------- -*/ -struct dc390_dcb -{ -struct dc390_dcb *pNextDCB; -struct dc390_acb *pDCBACB; - -/* Queued SRBs */ -struct dc390_srb *pGoingSRB; -struct dc390_srb *pGoingLast; -struct dc390_srb *pActiveSRB; -u8 GoingSRBCnt; - -u32 TagMask; - -u8 TargetID; /*; SCSI Target ID (SCSI Only) */ -u8 TargetLUN; /*; SCSI Log. Unit (SCSI Only) */ -u8 DevMode; -u8 DCBFlag; - -u8 CtrlR1; -u8 CtrlR3; -u8 CtrlR4; - -u8 SyncMode; /*; 0:async mode */ -u8 NegoPeriod; /*;for nego. */ -u8 SyncPeriod; /*;for reg. */ -u8 SyncOffset; /*;for reg. and nego.(low nibble) */ -}; - - -/* -;----------------------------------------------------------------------- -; Adapter Control Block -;----------------------------------------------------------------------- -*/ -struct dc390_acb -{ -struct Scsi_Host *pScsiHost; -u16 IOPortBase; -u8 IRQLevel; -u8 status; - -u8 SRBCount; -u8 AdapterIndex; /*; nth Adapter this driver */ -u8 DCBCnt; - -u8 TagMaxNum; -u8 ACBFlag; -u8 Gmode2; -u8 scan_devices; - -struct dc390_dcb *pLinkDCB; -struct dc390_dcb *pLastDCB; -struct dc390_dcb *pDCBRunRobin; - -struct dc390_dcb *pActiveDCB; -struct dc390_srb *pFreeSRB; -struct dc390_srb *pTmpSRB; - -u8 msgin123[4]; -u8 Connected; -u8 pad; - -#if defined(USE_SPINLOCKS) && USE_SPINLOCKS > 1 && (defined(CONFIG_SMP) || DEBUG_SPINLOCKS > 0) -spinlock_t lock; -#endif -u8 sel_timeout; -u8 glitch_cfg; - -u8 MsgLen; -u8 Ignore_IRQ; /* Not used */ - -struct pci_dev *pdev; - -unsigned long last_reset; -unsigned long Cmds; -u32 SelLost; -u32 SelConn; -u32 CmdInQ; -u32 CmdOutOfSRB; - -struct dc390_srb TmpSRB; -struct dc390_srb SRB_array[MAX_SRB_CNT]; /* 50 SRBs */ -}; - - -/*;-----------------------------------------------------------------------*/ - - -#define BIT31 0x80000000 -#define BIT30 0x40000000 -#define BIT29 0x20000000 -#define BIT28 0x10000000 -#define BIT27 0x08000000 -#define BIT26 0x04000000 -#define BIT25 0x02000000 -#define BIT24 0x01000000 -#define BIT23 0x00800000 -#define BIT22 0x00400000 -#define BIT21 0x00200000 -#define BIT20 0x00100000 -#define BIT19 0x00080000 -#define BIT18 0x00040000 -#define BIT17 0x00020000 -#define BIT16 0x00010000 -#define BIT15 0x00008000 -#define BIT14 0x00004000 -#define BIT13 0x00002000 -#define BIT12 0x00001000 -#define BIT11 0x00000800 -#define BIT10 0x00000400 -#define BIT9 0x00000200 -#define BIT8 0x00000100 -#define BIT7 0x00000080 -#define BIT6 0x00000040 -#define BIT5 0x00000020 -#define BIT4 0x00000010 -#define BIT3 0x00000008 -#define BIT2 0x00000004 -#define BIT1 0x00000002 -#define BIT0 0x00000001 - -/*;---UnitCtrlFlag */ -#define UNIT_ALLOCATED BIT0 -#define UNIT_INFO_CHANGED BIT1 -#define FORMATING_MEDIA BIT2 -#define UNIT_RETRY BIT3 - -/*;---UnitFlags */ -#define DASD_SUPPORT BIT0 -#define SCSI_SUPPORT BIT1 -#define ASPI_SUPPORT BIT2 - -/*;----SRBState machine definition */ -#define SRB_FREE 0 -#define SRB_WAIT BIT0 -#define SRB_READY BIT1 -#define SRB_MSGOUT BIT2 /*;arbitration+msg_out 1st byte*/ -#define SRB_MSGIN BIT3 -#define SRB_MSGIN_MULTI BIT4 -#define SRB_COMMAND BIT5 -#define SRB_START_ BIT6 /*;arbitration+msg_out+command_out*/ -#define SRB_DISCONNECT BIT7 -#define SRB_DATA_XFER BIT8 -#define SRB_XFERPAD BIT9 -#define SRB_STATUS BIT10 -#define SRB_COMPLETED BIT11 -#define SRB_ABORT_SENT BIT12 -#define DO_SYNC_NEGO BIT13 -#define SRB_UNEXPECT_RESEL BIT14 - -/*;---SRBstatus */ -#define SRB_OK BIT0 -#define ABORTION BIT1 -#define OVER_RUN BIT2 -#define UNDER_RUN BIT3 -#define PARITY_ERROR BIT4 -#define SRB_ERROR BIT5 - -/*;---ACBFlag */ -#define RESET_DEV BIT0 -#define RESET_DETECT BIT1 -#define RESET_DONE BIT2 - -/*;---DCBFlag */ -#define ABORT_DEV_ BIT0 - -/*;---SRBFlag */ -#define DATAOUT BIT7 -#define DATAIN BIT6 -#define RESIDUAL_VALID BIT5 -#define ENABLE_TIMER BIT4 -#define RESET_DEV0 BIT2 -#define ABORT_DEV BIT1 -#define AUTO_REQSENSE BIT0 - -/*;---Adapter status */ -#define H_STATUS_GOOD 0 -#define H_SEL_TIMEOUT 0x11 -#define H_OVER_UNDER_RUN 0x12 -#define H_UNEXP_BUS_FREE 0x13 -#define H_TARGET_PHASE_F 0x14 -#define H_INVALID_CCB_OP 0x16 -#define H_LINK_CCB_BAD 0x17 -#define H_BAD_TARGET_DIR 0x18 -#define H_DUPLICATE_CCB 0x19 -#define H_BAD_CCB_OR_SG 0x1A -#define H_ABORT 0x0FF - -/* cmd->result */ -#define RES_TARGET 0x000000FF /* Target State */ -#define RES_TARGET_LNX STATUS_MASK /* Only official ... */ -#define RES_ENDMSG 0x0000FF00 /* End Message */ -#define RES_DID 0x00FF0000 /* DID_ codes */ -#define RES_DRV 0xFF000000 /* DRIVER_ codes */ - -#define MK_RES(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)) -#define MK_RES_LNX(drv,did,msg,tgt) ((int)(drv)<<24 | (int)(did)<<16 | (int)(msg)<<8 | (int)(tgt)) - -#define SET_RES_TARGET(who, tgt) do { who &= ~RES_TARGET; who |= (int)(tgt); } while (0) -#define SET_RES_TARGET_LNX(who, tgt) do { who &= ~RES_TARGET_LNX; who |= (int)(tgt) << 1; } while (0) -#define SET_RES_MSG(who, msg) do { who &= ~RES_ENDMSG; who |= (int)(msg) << 8; } while (0) -#define SET_RES_DID(who, did) do { who &= ~RES_DID; who |= (int)(did) << 16; } while (0) -#define SET_RES_DRV(who, drv) do { who &= ~RES_DRV; who |= (int)(drv) << 24; } while (0) - -/*;---Sync_Mode */ -#define SYNC_DISABLE 0 -#define SYNC_ENABLE BIT0 -#define SYNC_NEGO_DONE BIT1 -#define WIDE_ENABLE BIT2 /* Not used ;-) */ -#define WIDE_NEGO_DONE BIT3 /* Not used ;-) */ -#define EN_TAG_QUEUEING BIT4 -#define EN_ATN_STOP BIT5 - -#define SYNC_NEGO_OFFSET 15 - -/*;---SCSI bus phase*/ -#define SCSI_DATA_OUT 0 -#define SCSI_DATA_IN 1 -#define SCSI_COMMAND 2 -#define SCSI_STATUS_ 3 -#define SCSI_NOP0 4 -#define SCSI_NOP1 5 -#define SCSI_MSG_OUT 6 -#define SCSI_MSG_IN 7 - -/*;----SCSI MSG BYTE*/ /* see scsi/scsi.h */ /* One is missing ! */ -#define ABORT_TAG 0x0d - -/* - * SISC query queue - */ -typedef struct { - dma_addr_t saved_dma_handle; -} dc390_cmd_scp_t; - -/* -;========================================================== -; EEPROM byte offset -;========================================================== -*/ -typedef struct _EEprom -{ -u8 EE_MODE1; -u8 EE_SPEED; -u8 xx1; -u8 xx2; -} EEprom, *PEEprom; - -#define REAL_EE_ADAPT_SCSI_ID 64 -#define REAL_EE_MODE2 65 -#define REAL_EE_DELAY 66 -#define REAL_EE_TAG_CMD_NUM 67 - -#define EE_ADAPT_SCSI_ID 32 -#define EE_MODE2 33 -#define EE_DELAY 34 -#define EE_TAG_CMD_NUM 35 - -#define EE_LEN 40 - -/*; EE_MODE1 bits definition*/ -#define PARITY_CHK_ BIT0 -#define SYNC_NEGO_ BIT1 -#define EN_DISCONNECT_ BIT2 -#define SEND_START_ BIT3 -#define TAG_QUEUEING_ BIT4 - -/*; EE_MODE2 bits definition*/ -#define MORE2_DRV BIT0 -#define GREATER_1G BIT1 -#define RST_SCSI_BUS BIT2 -#define ACTIVE_NEGATION BIT3 -#define NO_SEEK BIT4 -#define LUN_CHECK BIT5 - -#define ENABLE_CE 1 -#define DISABLE_CE 0 -#define EEPROM_READ 0x80 - -/* -;========================================================== -; AMD 53C974 Registers bit Definition -;========================================================== -*/ -/* -;==================== -; SCSI Register -;==================== -*/ - -/*; Command Reg.(+0CH) (rw) */ -#define DMA_COMMAND BIT7 -#define NOP_CMD 0 -#define CLEAR_FIFO_CMD 1 -#define RST_DEVICE_CMD 2 -#define RST_SCSI_BUS_CMD 3 - -#define INFO_XFER_CMD 0x10 -#define INITIATOR_CMD_CMPLTE 0x11 -#define MSG_ACCEPTED_CMD 0x12 -#define XFER_PAD_BYTE 0x18 -#define SET_ATN_CMD 0x1A -#define RESET_ATN_CMD 0x1B - -#define SEL_WO_ATN 0x41 /* currently not used */ -#define SEL_W_ATN 0x42 -#define SEL_W_ATN_STOP 0x43 -#define SEL_W_ATN3 0x46 -#define EN_SEL_RESEL 0x44 -#define DIS_SEL_RESEL 0x45 /* currently not used */ -#define RESEL 0x40 /* " */ -#define RESEL_ATN3 0x47 /* " */ - -#define DATA_XFER_CMD INFO_XFER_CMD - - -/*; SCSI Status Reg.(+10H) (r) */ -#define INTERRUPT BIT7 -#define ILLEGAL_OP_ERR BIT6 -#define PARITY_ERR BIT5 -#define COUNT_2_ZERO BIT4 -#define GROUP_CODE_VALID BIT3 -#define SCSI_PHASE_MASK (BIT2+BIT1+BIT0) -/* BIT2: MSG phase; BIT1: C/D physe; BIT0: I/O phase */ - -/*; Interrupt Status Reg.(+14H) (r) */ -#define SCSI_RESET BIT7 -#define INVALID_CMD BIT6 -#define DISCONNECTED BIT5 -#define SERVICE_REQUEST BIT4 -#define SUCCESSFUL_OP BIT3 -#define RESELECTED BIT2 -#define SEL_ATTENTION BIT1 -#define SELECTED BIT0 - -/*; Internal State Reg.(+18H) (r) */ -#define SYNC_OFFSET_FLAG BIT3 -#define INTRN_STATE_MASK (BIT2+BIT1+BIT0) -/* 0x04: Sel. successful (w/o stop), 0x01: Sel. successful (w/ stop) */ - -/*; Clock Factor Reg.(+24H) (w) */ -#define CLK_FREQ_40MHZ 0 -#define CLK_FREQ_35MHZ (BIT2+BIT1+BIT0) -#define CLK_FREQ_30MHZ (BIT2+BIT1) -#define CLK_FREQ_25MHZ (BIT2+BIT0) -#define CLK_FREQ_20MHZ BIT2 -#define CLK_FREQ_15MHZ (BIT1+BIT0) -#define CLK_FREQ_10MHZ BIT1 - -/*; Control Reg. 1(+20H) (rw) */ -#define EXTENDED_TIMING BIT7 -#define DIS_INT_ON_SCSI_RST BIT6 -#define PARITY_ERR_REPO BIT4 -#define SCSI_ID_ON_BUS (BIT2+BIT1+BIT0) /* host adapter ID */ - -/*; Control Reg. 2(+2CH) (rw) */ -#define EN_FEATURE BIT6 -#define EN_SCSI2_CMD BIT3 - -/*; Control Reg. 3(+30H) (rw) */ -#define ID_MSG_CHECK BIT7 -#define EN_QTAG_MSG BIT6 -#define EN_GRP2_CMD BIT5 -#define FAST_SCSI BIT4 /* ;10MB/SEC */ -#define FAST_CLK BIT3 /* ;25 - 40 MHZ */ - -/*; Control Reg. 4(+34H) (rw) */ -#define EATER_12NS 0 -#define EATER_25NS BIT7 -#define EATER_35NS BIT6 -#define EATER_0NS (BIT7+BIT6) -#define REDUCED_POWER BIT5 -#define CTRL4_RESERVED BIT4 /* must be 1 acc. to AM53C974.c */ -#define NEGATE_REQACKDATA BIT2 -#define NEGATE_REQACK BIT3 - -#define GLITCH_TO_NS(x) (((~x>>6 & 2) >> 1) | ((x>>6 & 1) << 1 ^ (x>>6 & 2))) -#define NS_TO_GLITCH(y) (((~y<<7) | ~((y<<6) ^ ((y<<5 & 1<<6) | ~0x40))) & 0xc0) - -/* -;==================== -; DMA Register -;==================== -*/ -/*; DMA Command Reg.(+40H) (rw) */ -#define READ_DIRECTION BIT7 -#define WRITE_DIRECTION 0 -#define EN_DMA_INT BIT6 -#define EN_PAGE_INT BIT5 /* page transfer interrupt enable */ -#define MAP_TO_MDL BIT4 -#define DIAGNOSTIC BIT2 -#define DMA_IDLE_CMD 0 -#define DMA_BLAST_CMD BIT0 -#define DMA_ABORT_CMD BIT1 -#define DMA_START_CMD (BIT1+BIT0) - -/*; DMA Status Reg.(+54H) (r) */ -#define PCI_MS_ABORT BIT6 -#define BLAST_COMPLETE BIT5 -#define SCSI_INTERRUPT BIT4 -#define DMA_XFER_DONE BIT3 -#define DMA_XFER_ABORT BIT2 -#define DMA_XFER_ERROR BIT1 -#define POWER_DOWN BIT0 - -/*; DMA SCSI Bus and Ctrl.(+70H) */ -#define EN_INT_ON_PCI_ABORT BIT25 -#define WRT_ERASE_DMA_STAT BIT24 -#define PW_DOWN_CTRL BIT21 -#define SCSI_BUSY BIT20 -#define SCLK BIT19 -#define SCAM BIT18 -#define SCSI_LINES 0x0003ffff - -/* -;========================================================== -; SCSI Chip register address offset -;========================================================== -;Registers are rw unless declared otherwise -*/ -#define CtcReg_Low 0x00 /* r curr. transfer count */ -#define CtcReg_Mid 0x04 /* r */ -#define CtcReg_High 0x38 /* r */ -#define ScsiFifo 0x08 -#define ScsiCmd 0x0C -#define Scsi_Status 0x10 /* r */ -#define INT_Status 0x14 /* r */ -#define Sync_Period 0x18 /* w */ -#define Sync_Offset 0x1C /* w */ -#define Clk_Factor 0x24 /* w */ -#define CtrlReg1 0x20 -#define CtrlReg2 0x2C -#define CtrlReg3 0x30 -#define CtrlReg4 0x34 -#define DMA_Cmd 0x40 -#define DMA_XferCnt 0x44 /* rw starting transfer count (32 bit) */ -#define DMA_XferAddr 0x48 /* rw starting physical address (32 bit) */ -#define DMA_Wk_ByteCntr 0x4C /* r working byte counter */ -#define DMA_Wk_AddrCntr 0x50 /* r working address counter */ -#define DMA_Status 0x54 /* r */ -#define DMA_MDL_Addr 0x58 /* rw starting MDL address */ -#define DMA_Wk_MDL_Cntr 0x5C /* r working MDL counter */ -#define DMA_ScsiBusCtrl 0x70 /* rw SCSI Bus, PCI/DMA Ctrl */ - -#define StcReg_Low CtcReg_Low /* w start transfer count */ -#define StcReg_Mid CtcReg_Mid /* w */ -#define StcReg_High CtcReg_High /* w */ -#define Scsi_Dest_ID Scsi_Status /* w */ -#define Scsi_TimeOut INT_Status /* w */ -#define Intern_State Sync_Period /* r */ -#define Current_Fifo Sync_Offset /* r Curr. FIFO / int. state */ - - -#define DC390_read8(address) \ - (inb (pACB->IOPortBase + (address))) - -#define DC390_read8_(address, base) \ - (inb ((u16)(base) + (address))) - -#define DC390_read16(address) \ - (inw (pACB->IOPortBase + (address))) - -#define DC390_read32(address) \ - (inl (pACB->IOPortBase + (address))) - -#define DC390_write8(address,value) \ - outb ((value), pACB->IOPortBase + (address)) - -#define DC390_write8_(address,value,base) \ - outb ((value), (u16)(base) + (address)) - -#define DC390_write16(address,value) \ - outw ((value), pACB->IOPortBase + (address)) - -#define DC390_write32(address,value) \ - outl ((value), pACB->IOPortBase + (address)) - - -#endif /* _TMSCSIM_H */ |