diff options
Diffstat (limited to 'drivers/scsi')
27 files changed, 4858 insertions, 312 deletions
diff --git a/drivers/scsi/3w-9xxx.c b/drivers/scsi/3w-9xxx.c index a6ac61611f3..a748fbfb669 100644 --- a/drivers/scsi/3w-9xxx.c +++ b/drivers/scsi/3w-9xxx.c @@ -60,6 +60,7 @@ Remove un-needed eh_abort handler. Add support for embedded firmware error strings. 2.26.02.003 - Correctly handle single sgl's with use_sg=1. + 2.26.02.004 - Add support for 9550SX controllers. */ #include <linux/module.h> @@ -82,7 +83,7 @@ #include "3w-9xxx.h" /* Globals */ -#define TW_DRIVER_VERSION "2.26.02.003" +#define TW_DRIVER_VERSION "2.26.02.004" static TW_Device_Extension *twa_device_extension_list[TW_MAX_SLOT]; static unsigned int twa_device_extension_count; static int twa_major = -1; @@ -892,11 +893,6 @@ static int twa_decode_bits(TW_Device_Extension *tw_dev, u32 status_reg_value) writel(TW_CONTROL_CLEAR_QUEUE_ERROR, TW_CONTROL_REG_ADDR(tw_dev)); } - if (status_reg_value & TW_STATUS_SBUF_WRITE_ERROR) { - TW_PRINTK(tw_dev->host, TW_DRIVER, 0xf, "SBUF Write Error: clearing"); - writel(TW_CONTROL_CLEAR_SBUF_WRITE_ERROR, TW_CONTROL_REG_ADDR(tw_dev)); - } - if (status_reg_value & TW_STATUS_MICROCONTROLLER_ERROR) { if (tw_dev->reset_print == 0) { TW_PRINTK(tw_dev->host, TW_DRIVER, 0x10, "Microcontroller Error: clearing"); @@ -930,6 +926,36 @@ out: return retval; } /* End twa_empty_response_queue() */ +/* This function will clear the pchip/response queue on 9550SX */ +static int twa_empty_response_queue_large(TW_Device_Extension *tw_dev) +{ + u32 status_reg_value, response_que_value; + int count = 0, retval = 1; + + if (tw_dev->tw_pci_dev->device == PCI_DEVICE_ID_3WARE_9550SX) { + status_reg_value = readl(TW_STATUS_REG_ADDR(tw_dev)); + + while (((status_reg_value & TW_STATUS_RESPONSE_QUEUE_EMPTY) == 0) && (count < TW_MAX_RESPONSE_DRAIN)) { + response_que_value = readl(TW_RESPONSE_QUEUE_REG_ADDR_LARGE(tw_dev)); + if ((response_que_value & TW_9550SX_DRAIN_COMPLETED) == TW_9550SX_DRAIN_COMPLETED) { + /* P-chip settle time */ + msleep(500); + retval = 0; + goto out; + } + status_reg_value = readl(TW_STATUS_REG_ADDR(tw_dev)); + count++; + } + if (count == TW_MAX_RESPONSE_DRAIN) + goto out; + + retval = 0; + } else + retval = 0; +out: + return retval; +} /* End twa_empty_response_queue_large() */ + /* This function passes sense keys from firmware to scsi layer */ static int twa_fill_sense(TW_Device_Extension *tw_dev, int request_id, int copy_sense, int print_host) { @@ -1613,8 +1639,16 @@ static int twa_reset_sequence(TW_Device_Extension *tw_dev, int soft_reset) int tries = 0, retval = 1, flashed = 0, do_soft_reset = soft_reset; while (tries < TW_MAX_RESET_TRIES) { - if (do_soft_reset) + if (do_soft_reset) { TW_SOFT_RESET(tw_dev); + /* Clear pchip/response queue on 9550SX */ + if (twa_empty_response_queue_large(tw_dev)) { + TW_PRINTK(tw_dev->host, TW_DRIVER, 0x36, "Response queue (large) empty failed during reset sequence"); + do_soft_reset = 1; + tries++; + continue; + } + } /* Make sure controller is in a good state */ if (twa_poll_status(tw_dev, TW_STATUS_MICROCONTROLLER_READY | (do_soft_reset == 1 ? TW_STATUS_ATTENTION_INTERRUPT : 0), 60)) { @@ -2034,7 +2068,10 @@ static int __devinit twa_probe(struct pci_dev *pdev, const struct pci_device_id goto out_free_device_extension; } - mem_addr = pci_resource_start(pdev, 1); + if (pdev->device == PCI_DEVICE_ID_3WARE_9000) + mem_addr = pci_resource_start(pdev, 1); + else + mem_addr = pci_resource_start(pdev, 2); /* Save base address */ tw_dev->base_addr = ioremap(mem_addr, PAGE_SIZE); @@ -2148,6 +2185,8 @@ static void twa_remove(struct pci_dev *pdev) static struct pci_device_id twa_pci_tbl[] __devinitdata = { { PCI_VENDOR_ID_3WARE, PCI_DEVICE_ID_3WARE_9000, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, + { PCI_VENDOR_ID_3WARE, PCI_DEVICE_ID_3WARE_9550SX, + PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0}, { } }; MODULE_DEVICE_TABLE(pci, twa_pci_tbl); diff --git a/drivers/scsi/3w-9xxx.h b/drivers/scsi/3w-9xxx.h index 8c8ecbed3b5..46f22cdc829 100644 --- a/drivers/scsi/3w-9xxx.h +++ b/drivers/scsi/3w-9xxx.h @@ -267,7 +267,6 @@ static twa_message_type twa_error_table[] = { #define TW_CONTROL_CLEAR_PARITY_ERROR 0x00800000 #define TW_CONTROL_CLEAR_QUEUE_ERROR 0x00400000 #define TW_CONTROL_CLEAR_PCI_ABORT 0x00100000 -#define TW_CONTROL_CLEAR_SBUF_WRITE_ERROR 0x00000008 /* Status register bit definitions */ #define TW_STATUS_MAJOR_VERSION_MASK 0xF0000000 @@ -285,9 +284,8 @@ static twa_message_type twa_error_table[] = { #define TW_STATUS_MICROCONTROLLER_READY 0x00002000 #define TW_STATUS_COMMAND_QUEUE_EMPTY 0x00001000 #define TW_STATUS_EXPECTED_BITS 0x00002000 -#define TW_STATUS_UNEXPECTED_BITS 0x00F00008 -#define TW_STATUS_SBUF_WRITE_ERROR 0x00000008 -#define TW_STATUS_VALID_INTERRUPT 0x00DF0008 +#define TW_STATUS_UNEXPECTED_BITS 0x00F00000 +#define TW_STATUS_VALID_INTERRUPT 0x00DF0000 /* RESPONSE QUEUE BIT DEFINITIONS */ #define TW_RESPONSE_ID_MASK 0x00000FF0 @@ -324,9 +322,9 @@ static twa_message_type twa_error_table[] = { /* Compatibility defines */ #define TW_9000_ARCH_ID 0x5 -#define TW_CURRENT_DRIVER_SRL 28 -#define TW_CURRENT_DRIVER_BUILD 9 -#define TW_CURRENT_DRIVER_BRANCH 4 +#define TW_CURRENT_DRIVER_SRL 30 +#define TW_CURRENT_DRIVER_BUILD 80 +#define TW_CURRENT_DRIVER_BRANCH 0 /* Phase defines */ #define TW_PHASE_INITIAL 0 @@ -334,6 +332,7 @@ static twa_message_type twa_error_table[] = { #define TW_PHASE_SGLIST 2 /* Misc defines */ +#define TW_9550SX_DRAIN_COMPLETED 0xFFFF #define TW_SECTOR_SIZE 512 #define TW_ALIGNMENT_9000 4 /* 4 bytes */ #define TW_ALIGNMENT_9000_SGL 0x3 @@ -417,6 +416,9 @@ static twa_message_type twa_error_table[] = { #ifndef PCI_DEVICE_ID_3WARE_9000 #define PCI_DEVICE_ID_3WARE_9000 0x1002 #endif +#ifndef PCI_DEVICE_ID_3WARE_9550SX +#define PCI_DEVICE_ID_3WARE_9550SX 0x1003 +#endif /* Bitmask macros to eliminate bitfields */ @@ -443,6 +445,7 @@ static twa_message_type twa_error_table[] = { #define TW_STATUS_REG_ADDR(x) ((unsigned char __iomem *)x->base_addr + 0x4) #define TW_COMMAND_QUEUE_REG_ADDR(x) (sizeof(dma_addr_t) > 4 ? ((unsigned char __iomem *)x->base_addr + 0x20) : ((unsigned char __iomem *)x->base_addr + 0x8)) #define TW_RESPONSE_QUEUE_REG_ADDR(x) ((unsigned char __iomem *)x->base_addr + 0xC) +#define TW_RESPONSE_QUEUE_REG_ADDR_LARGE(x) ((unsigned char __iomem *)x->base_addr + 0x30) #define TW_CLEAR_ALL_INTERRUPTS(x) (writel(TW_STATUS_VALID_INTERRUPT, TW_CONTROL_REG_ADDR(x))) #define TW_CLEAR_ATTENTION_INTERRUPT(x) (writel(TW_CONTROL_CLEAR_ATTENTION_INTERRUPT, TW_CONTROL_REG_ADDR(x))) #define TW_CLEAR_HOST_INTERRUPT(x) (writel(TW_CONTROL_CLEAR_HOST_INTERRUPT, TW_CONTROL_REG_ADDR(x))) diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile index 1e4edbdf273..48529d180ca 100644 --- a/drivers/scsi/Makefile +++ b/drivers/scsi/Makefile @@ -99,6 +99,7 @@ obj-$(CONFIG_SCSI_DC395x) += dc395x.o obj-$(CONFIG_SCSI_DC390T) += tmscsim.o obj-$(CONFIG_MEGARAID_LEGACY) += megaraid.o obj-$(CONFIG_MEGARAID_NEWGEN) += megaraid/ +obj-$(CONFIG_MEGARAID_SAS) += megaraid/ obj-$(CONFIG_SCSI_ACARD) += atp870u.o obj-$(CONFIG_SCSI_SUNESP) += esp.o obj-$(CONFIG_SCSI_GDTH) += gdth.o diff --git a/drivers/scsi/aacraid/aachba.c b/drivers/scsi/aacraid/aachba.c index a8e3dfcd0dc..93416f760e5 100644 --- a/drivers/scsi/aacraid/aachba.c +++ b/drivers/scsi/aacraid/aachba.c @@ -313,18 +313,37 @@ int aac_get_containers(struct aac_dev *dev) } dresp = (struct aac_mount *)fib_data(fibptr); + if ((le32_to_cpu(dresp->status) == ST_OK) && + (le32_to_cpu(dresp->mnt[0].vol) == CT_NONE)) { + dinfo->command = cpu_to_le32(VM_NameServe64); + dinfo->count = cpu_to_le32(index); + dinfo->type = cpu_to_le32(FT_FILESYS); + + if (fib_send(ContainerCommand, + fibptr, + sizeof(struct aac_query_mount), + FsaNormal, + 1, 1, + NULL, NULL) < 0) + continue; + } else + dresp->mnt[0].capacityhigh = 0; + dprintk ((KERN_DEBUG - "VM_NameServe cid=%d status=%d vol=%d state=%d cap=%u\n", + "VM_NameServe cid=%d status=%d vol=%d state=%d cap=%llu\n", (int)index, (int)le32_to_cpu(dresp->status), (int)le32_to_cpu(dresp->mnt[0].vol), (int)le32_to_cpu(dresp->mnt[0].state), - (unsigned)le32_to_cpu(dresp->mnt[0].capacity))); + ((u64)le32_to_cpu(dresp->mnt[0].capacity)) + + (((u64)le32_to_cpu(dresp->mnt[0].capacityhigh)) << 32))); if ((le32_to_cpu(dresp->status) == ST_OK) && (le32_to_cpu(dresp->mnt[0].vol) != CT_NONE) && (le32_to_cpu(dresp->mnt[0].state) != FSCS_HIDDEN)) { fsa_dev_ptr[index].valid = 1; fsa_dev_ptr[index].type = le32_to_cpu(dresp->mnt[0].vol); - fsa_dev_ptr[index].size = le32_to_cpu(dresp->mnt[0].capacity); + fsa_dev_ptr[index].size + = ((u64)le32_to_cpu(dresp->mnt[0].capacity)) + + (((u64)le32_to_cpu(dresp->mnt[0].capacityhigh)) << 32); if (le32_to_cpu(dresp->mnt[0].state) & FSCS_READONLY) fsa_dev_ptr[index].ro = 1; } @@ -460,7 +479,7 @@ static int aac_get_container_name(struct scsi_cmnd * scsicmd, int cid) * is updated in the struct fsa_dev_info structure rather than returned. */ -static int probe_container(struct aac_dev *dev, int cid) +int probe_container(struct aac_dev *dev, int cid) { struct fsa_dev_info *fsa_dev_ptr; int status; @@ -497,11 +516,29 @@ static int probe_container(struct aac_dev *dev, int cid) dresp = (struct aac_mount *) fib_data(fibptr); if ((le32_to_cpu(dresp->status) == ST_OK) && + (le32_to_cpu(dresp->mnt[0].vol) == CT_NONE)) { + dinfo->command = cpu_to_le32(VM_NameServe64); + dinfo->count = cpu_to_le32(cid); + dinfo->type = cpu_to_le32(FT_FILESYS); + + if (fib_send(ContainerCommand, + fibptr, + sizeof(struct aac_query_mount), + FsaNormal, + 1, 1, + NULL, NULL) < 0) + goto error; + } else + dresp->mnt[0].capacityhigh = 0; + + if ((le32_to_cpu(dresp->status) == ST_OK) && (le32_to_cpu(dresp->mnt[0].vol) != CT_NONE) && (le32_to_cpu(dresp->mnt[0].state) != FSCS_HIDDEN)) { fsa_dev_ptr[cid].valid = 1; fsa_dev_ptr[cid].type = le32_to_cpu(dresp->mnt[0].vol); - fsa_dev_ptr[cid].size = le32_to_cpu(dresp->mnt[0].capacity); + fsa_dev_ptr[cid].size + = ((u64)le32_to_cpu(dresp->mnt[0].capacity)) + + (((u64)le32_to_cpu(dresp->mnt[0].capacityhigh)) << 32); if (le32_to_cpu(dresp->mnt[0].state) & FSCS_READONLY) fsa_dev_ptr[cid].ro = 1; } @@ -655,7 +692,7 @@ int aac_get_adapter_info(struct aac_dev* dev) fibptr, sizeof(*info), FsaNormal, - 1, 1, + -1, 1, /* First `interrupt' command uses special wait */ NULL, NULL); @@ -806,8 +843,8 @@ int aac_get_adapter_info(struct aac_dev* dev) if (!(dev->raw_io_interface)) { dev->scsi_host_ptr->sg_tablesize = (dev->max_fib_size - sizeof(struct aac_fibhdr) - - sizeof(struct aac_write) + sizeof(struct sgmap)) / - sizeof(struct sgmap); + sizeof(struct aac_write) + sizeof(struct sgentry)) / + sizeof(struct sgentry); if (dev->dac_support) { /* * 38 scatter gather elements @@ -816,8 +853,8 @@ int aac_get_adapter_info(struct aac_dev* dev) (dev->max_fib_size - sizeof(struct aac_fibhdr) - sizeof(struct aac_write64) + - sizeof(struct sgmap64)) / - sizeof(struct sgmap64); + sizeof(struct sgentry64)) / + sizeof(struct sgentry64); } dev->scsi_host_ptr->max_sectors = AAC_MAX_32BIT_SGBCOUNT; if(!(dev->adapter_info.options & AAC_OPT_NEW_COMM)) { @@ -854,7 +891,40 @@ static void io_callback(void *context, struct fib * fibptr) dev = (struct aac_dev *)scsicmd->device->host->hostdata; cid = ID_LUN_TO_CONTAINER(scsicmd->device->id, scsicmd->device->lun); - dprintk((KERN_DEBUG "io_callback[cpu %d]: lba = %u, t = %ld.\n", smp_processor_id(), ((scsicmd->cmnd[1] & 0x1F) << 16) | (scsicmd->cmnd[2] << 8) | scsicmd->cmnd[3], jiffies)); + if (nblank(dprintk(x))) { + u64 lba; + switch (scsicmd->cmnd[0]) { + case WRITE_6: + case READ_6: + lba = ((scsicmd->cmnd[1] & 0x1F) << 16) | + (scsicmd->cmnd[2] << 8) | scsicmd->cmnd[3]; + break; + case WRITE_16: + case READ_16: + lba = ((u64)scsicmd->cmnd[2] << 56) | + ((u64)scsicmd->cmnd[3] << 48) | + ((u64)scsicmd->cmnd[4] << 40) | + ((u64)scsicmd->cmnd[5] << 32) | + ((u64)scsicmd->cmnd[6] << 24) | + (scsicmd->cmnd[7] << 16) | + (scsicmd->cmnd[8] << 8) | scsicmd->cmnd[9]; + break; + case WRITE_12: + case READ_12: + lba = ((u64)scsicmd->cmnd[2] << 24) | + (scsicmd->cmnd[3] << 16) | + (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; + break; + default: + lba = ((u64)scsicmd->cmnd[2] << 24) | + (scsicmd->cmnd[3] << 16) | + (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; + break; + } + printk(KERN_DEBUG + "io_callback[cpu %d]: lba = %llu, t = %ld.\n", + smp_processor_id(), (unsigned long long)lba, jiffies); + } if (fibptr == NULL) BUG(); @@ -895,7 +965,7 @@ static void io_callback(void *context, struct fib * fibptr) static int aac_read(struct scsi_cmnd * scsicmd, int cid) { - u32 lba; + u64 lba; u32 count; int status; @@ -907,23 +977,69 @@ static int aac_read(struct scsi_cmnd * scsicmd, int cid) /* * Get block address and transfer length */ - if (scsicmd->cmnd[0] == READ_6) /* 6 byte command */ - { + switch (scsicmd->cmnd[0]) { + case READ_6: dprintk((KERN_DEBUG "aachba: received a read(6) command on id %d.\n", cid)); - lba = ((scsicmd->cmnd[1] & 0x1F) << 16) | (scsicmd->cmnd[2] << 8) | scsicmd->cmnd[3]; + lba = ((scsicmd->cmnd[1] & 0x1F) << 16) | + (scsicmd->cmnd[2] << 8) | scsicmd->cmnd[3]; count = scsicmd->cmnd[4]; if (count == 0) count = 256; - } else { + break; + case READ_16: + dprintk((KERN_DEBUG "aachba: received a read(16) command on id %d.\n", cid)); + + lba = ((u64)scsicmd->cmnd[2] << 56) | + ((u64)scsicmd->cmnd[3] << 48) | + ((u64)scsicmd->cmnd[4] << 40) | + ((u64)scsicmd->cmnd[5] << 32) | + ((u64)scsicmd->cmnd[6] << 24) | + (scsicmd->cmnd[7] << 16) | + (scsicmd->cmnd[8] << 8) | scsicmd->cmnd[9]; + count = (scsicmd->cmnd[10] << 24) | + (scsicmd->cmnd[11] << 16) | + (scsicmd->cmnd[12] << 8) | scsicmd->cmnd[13]; + break; + case READ_12: + dprintk((KERN_DEBUG "aachba: received a read(12) command on id %d.\n", cid)); + + lba = ((u64)scsicmd->cmnd[2] << 24) | + (scsicmd->cmnd[3] << 16) | + (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; + count = (scsicmd->cmnd[6] << 24) | + (scsicmd->cmnd[7] << 16) | + (scsicmd->cmnd[8] << 8) | scsicmd->cmnd[9]; + break; + default: dprintk((KERN_DEBUG "aachba: received a read(10) command on id %d.\n", cid)); - lba = (scsicmd->cmnd[2] << 24) | (scsicmd->cmnd[3] << 16) | (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; + lba = ((u64)scsicmd->cmnd[2] << 24) | + (scsicmd->cmnd[3] << 16) | + (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; count = (scsicmd->cmnd[7] << 8) | scsicmd->cmnd[8]; + break; } - dprintk((KERN_DEBUG "aac_read[cpu %d]: lba = %u, t = %ld.\n", + dprintk((KERN_DEBUG "aac_read[cpu %d]: lba = %llu, t = %ld.\n", smp_processor_id(), (unsigned long long)lba, jiffies)); + if ((!(dev->raw_io_interface) || !(dev->raw_io_64)) && + (lba & 0xffffffff00000000LL)) { + dprintk((KERN_DEBUG "aac_read: Illegal lba\n")); + scsicmd->result = DID_OK << 16 | COMMAND_COMPLETE << 8 | + SAM_STAT_CHECK_CONDITION; + set_sense((u8 *) &dev->fsa_dev[cid].sense_data, + HARDWARE_ERROR, + SENCODE_INTERNAL_TARGET_FAILURE, + ASENCODE_INTERNAL_TARGET_FAILURE, 0, 0, + 0, 0); + memcpy(scsicmd->sense_buffer, &dev->fsa_dev[cid].sense_data, + (sizeof(dev->fsa_dev[cid].sense_data) > sizeof(scsicmd->sense_buffer)) + ? sizeof(scsicmd->sense_buffer) + : sizeof(dev->fsa_dev[cid].sense_data)); + scsicmd->scsi_done(scsicmd); + return 0; + } /* * Alocate and initialize a Fib */ @@ -936,8 +1052,8 @@ static int aac_read(struct scsi_cmnd * scsicmd, int cid) if (dev->raw_io_interface) { struct aac_raw_io *readcmd; readcmd = (struct aac_raw_io *) fib_data(cmd_fibcontext); - readcmd->block[0] = cpu_to_le32(lba); - readcmd->block[1] = 0; + readcmd->block[0] = cpu_to_le32((u32)(lba&0xffffffff)); + readcmd->block[1] = cpu_to_le32((u32)((lba&0xffffffff00000000LL)>>32)); readcmd->count = cpu_to_le32(count<<9); readcmd->cid = cpu_to_le16(cid); readcmd->flags = cpu_to_le16(1); @@ -964,7 +1080,7 @@ static int aac_read(struct scsi_cmnd * scsicmd, int cid) readcmd->command = cpu_to_le32(VM_CtHostRead64); readcmd->cid = cpu_to_le16(cid); readcmd->sector_count = cpu_to_le16(count); - readcmd->block = cpu_to_le32(lba); + readcmd->block = cpu_to_le32((u32)(lba&0xffffffff)); readcmd->pad = 0; readcmd->flags = 0; @@ -989,7 +1105,7 @@ static int aac_read(struct scsi_cmnd * scsicmd, int cid) readcmd = (struct aac_read *) fib_data(cmd_fibcontext); readcmd->command = cpu_to_le32(VM_CtBlockRead); readcmd->cid = cpu_to_le32(cid); - readcmd->block = cpu_to_le32(lba); + readcmd->block = cpu_to_le32((u32)(lba&0xffffffff)); readcmd->count = cpu_to_le32(count * 512); aac_build_sg(scsicmd, &readcmd->sg); @@ -1031,7 +1147,7 @@ static int aac_read(struct scsi_cmnd * scsicmd, int cid) static int aac_write(struct scsi_cmnd * scsicmd, int cid) { - u32 lba; + u64 lba; u32 count; int status; u16 fibsize; @@ -1048,13 +1164,48 @@ static int aac_write(struct scsi_cmnd * scsicmd, int cid) count = scsicmd->cmnd[4]; if (count == 0) count = 256; + } else if (scsicmd->cmnd[0] == WRITE_16) { /* 16 byte command */ + dprintk((KERN_DEBUG "aachba: received a write(16) command on id %d.\n", cid)); + + lba = ((u64)scsicmd->cmnd[2] << 56) | + ((u64)scsicmd->cmnd[3] << 48) | + ((u64)scsicmd->cmnd[4] << 40) | + ((u64)scsicmd->cmnd[5] << 32) | + ((u64)scsicmd->cmnd[6] << 24) | + (scsicmd->cmnd[7] << 16) | + (scsicmd->cmnd[8] << 8) | scsicmd->cmnd[9]; + count = (scsicmd->cmnd[10] << 24) | (scsicmd->cmnd[11] << 16) | + (scsicmd->cmnd[12] << 8) | scsicmd->cmnd[13]; + } else if (scsicmd->cmnd[0] == WRITE_12) { /* 12 byte command */ + dprintk((KERN_DEBUG "aachba: received a write(12) command on id %d.\n", cid)); + + lba = ((u64)scsicmd->cmnd[2] << 24) | (scsicmd->cmnd[3] << 16) + | (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; + count = (scsicmd->cmnd[6] << 24) | (scsicmd->cmnd[7] << 16) + | (scsicmd->cmnd[8] << 8) | scsicmd->cmnd[9]; } else { dprintk((KERN_DEBUG "aachba: received a write(10) command on id %d.\n", cid)); - lba = (scsicmd->cmnd[2] << 24) | (scsicmd->cmnd[3] << 16) | (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; + lba = ((u64)scsicmd->cmnd[2] << 24) | (scsicmd->cmnd[3] << 16) | (scsicmd->cmnd[4] << 8) | scsicmd->cmnd[5]; count = (scsicmd->cmnd[7] << 8) | scsicmd->cmnd[8]; } - dprintk((KERN_DEBUG "aac_write[cpu %d]: lba = %u, t = %ld.\n", + dprintk((KERN_DEBUG "aac_write[cpu %d]: lba = %llu, t = %ld.\n", smp_processor_id(), (unsigned long long)lba, jiffies)); + if ((!(dev->raw_io_interface) || !(dev->raw_io_64)) + && (lba & 0xffffffff00000000LL)) { + dprintk((KERN_DEBUG "aac_write: Illegal lba\n")); + scsicmd->result = DID_OK << 16 | COMMAND_COMPLETE << 8 | SAM_STAT_CHECK_CONDITION; + set_sense((u8 *) &dev->fsa_dev[cid].sense_data, + HARDWARE_ERROR, + SENCODE_INTERNAL_TARGET_FAILURE, + ASENCODE_INTERNAL_TARGET_FAILURE, 0, 0, + 0, 0); + memcpy(scsicmd->sense_buffer, &dev->fsa_dev[cid].sense_data, + (sizeof(dev->fsa_dev[cid].sense_data) > sizeof(scsicmd->sense_buffer)) + ? sizeof(scsicmd->sense_buffer) + : sizeof(dev->fsa_dev[cid].sense_data)); + scsicmd->scsi_done(scsicmd); + return 0; + } /* * Allocate and initialize a Fib then setup a BlockWrite command */ @@ -1068,8 +1219,8 @@ static int aac_write(struct scsi_cmnd * scsicmd, int cid) if (dev->raw_io_interface) { struct aac_raw_io *writecmd; writecmd = (struct aac_raw_io *) fib_data(cmd_fibcontext); - writecmd->block[0] = cpu_to_le32(lba); - writecmd->block[1] = 0; + writecmd->block[0] = cpu_to_le32((u32)(lba&0xffffffff)); + writecmd->block[1] = cpu_to_le32((u32)((lba&0xffffffff00000000LL)>>32)); writecmd->count = cpu_to_le32(count<<9); writecmd->cid = cpu_to_le16(cid); writecmd->flags = 0; @@ -1096,7 +1247,7 @@ static int aac_write(struct scsi_cmnd * scsicmd, int cid) writecmd->command = cpu_to_le32(VM_CtHostWrite64); writecmd->cid = cpu_to_le16(cid); writecmd->sector_count = cpu_to_le16(count); - writecmd->block = cpu_to_le32(lba); + writecmd->block = cpu_to_le32((u32)(lba&0xffffffff)); writecmd->pad = 0; writecmd->flags = 0; @@ -1121,7 +1272,7 @@ static int aac_write(struct scsi_cmnd * scsicmd, int cid) writecmd = (struct aac_write *) fib_data(cmd_fibcontext); writecmd->command = cpu_to_le32(VM_CtBlockWrite); writecmd->cid = cpu_to_le32(cid); - writecmd->block = cpu_to_le32(lba); + writecmd->block = cpu_to_le32((u32)(lba&0xffffffff)); writecmd->count = cpu_to_le32(count * 512); writecmd->sg.count = cpu_to_le32(1); /* ->stable is not used - it did mean which type of write */ @@ -1310,11 +1461,18 @@ int aac_scsi_cmd(struct scsi_cmnd * scsicmd) */ if ((fsa_dev_ptr[cid].valid & 1) == 0) { switch (scsicmd->cmnd[0]) { + case SERVICE_ACTION_IN: + if (!(dev->raw_io_interface) || + !(dev->raw_io_64) || + ((scsicmd->cmnd[1] & 0x1f) != SAI_READ_CAPACITY_16)) + break; case INQUIRY: case READ_CAPACITY: case TEST_UNIT_READY: spin_unlock_irq(host->host_lock); probe_container(dev, cid); + if ((fsa_dev_ptr[cid].valid & 1) == 0) + fsa_dev_ptr[cid].valid = 0; spin_lock_irq(host->host_lock); if (fsa_dev_ptr[cid].valid == 0) { scsicmd->result = DID_NO_CONNECT << 16; @@ -1375,7 +1533,6 @@ int aac_scsi_cmd(struct scsi_cmnd * scsicmd) memset(&inq_data, 0, sizeof (struct inquiry_data)); inq_data.inqd_ver = 2; /* claim compliance to SCSI-2 */ - inq_data.inqd_dtq = 0x80; /* set RMB bit to one indicating that the medium is removable */ inq_data.inqd_rdf = 2; /* A response data format value of two indicates that the data shall be in the format specified in SCSI-2 */ inq_data.inqd_len = 31; /*Format for "pad2" is RelAdr | WBus32 | WBus16 | Sync | Linked |Reserved| CmdQue | SftRe */ @@ -1397,13 +1554,55 @@ int aac_scsi_cmd(struct scsi_cmnd * scsicmd) aac_internal_transfer(scsicmd, &inq_data, 0, sizeof(inq_data)); return aac_get_container_name(scsicmd, cid); } + case SERVICE_ACTION_IN: + if (!(dev->raw_io_interface) || + !(dev->raw_io_64) || + ((scsicmd->cmnd[1] & 0x1f) != SAI_READ_CAPACITY_16)) + break; + { + u64 capacity; + char cp[12]; + unsigned int offset = 0; + + dprintk((KERN_DEBUG "READ CAPACITY_16 command.\n")); + capacity = fsa_dev_ptr[cid].size - 1; + if (scsicmd->cmnd[13] > 12) { + offset = scsicmd->cmnd[13] - 12; + if (offset > sizeof(cp)) + break; + memset(cp, 0, offset); + aac_internal_transfer(scsicmd, cp, 0, offset); + } + cp[0] = (capacity >> 56) & 0xff; + cp[1] = (capacity >> 48) & 0xff; + cp[2] = (capacity >> 40) & 0xff; + cp[3] = (capacity >> 32) & 0xff; + cp[4] = (capacity >> 24) & 0xff; + cp[5] = (capacity >> 16) & 0xff; + cp[6] = (capacity >> 8) & 0xff; + cp[7] = (capacity >> 0) & 0xff; + cp[8] = 0; + cp[9] = 0; + cp[10] = 2; + cp[11] = 0; + aac_internal_transfer(scsicmd, cp, offset, sizeof(cp)); + + /* Do not cache partition table for arrays */ + scsicmd->device->removable = 1; + + scsicmd->result = DID_OK << 16 | COMMAND_COMPLETE << 8 | SAM_STAT_GOOD; + scsicmd->scsi_done(scsicmd); + + return 0; + } + case READ_CAPACITY: { u32 capacity; char cp[8]; dprintk((KERN_DEBUG "READ CAPACITY command.\n")); - if (fsa_dev_ptr[cid].size <= 0x100000000LL) + if (fsa_dev_ptr[cid].size <= 0x100000000ULL) capacity = fsa_dev_ptr[cid].size - 1; else capacity = (u32)-1; @@ -1417,6 +1616,8 @@ int aac_scsi_cmd(struct scsi_cmnd * scsicmd) cp[6] = 2; cp[7] = 0; aac_internal_transfer(scsicmd, cp, 0, sizeof(cp)); + /* Do not cache partition table for arrays */ + scsicmd->device->removable = 1; scsicmd->result = DID_OK << 16 | COMMAND_COMPLETE << 8 | SAM_STAT_GOOD; scsicmd->scsi_done(scsicmd); @@ -1497,6 +1698,8 @@ int aac_scsi_cmd(struct scsi_cmnd * scsicmd) { case READ_6: case READ_10: + case READ_12: + case READ_16: /* * Hack to keep track of ordinal number of the device that * corresponds to a container. Needed to convert @@ -1504,17 +1707,19 @@ int aac_scsi_cmd(struct scsi_cmnd * scsicmd) */ spin_unlock_irq(host->host_lock); - if (scsicmd->request->rq_disk) - memcpy(fsa_dev_ptr[cid].devname, - scsicmd->request->rq_disk->disk_name, - 8); - + if (scsicmd->request->rq_disk) + strlcpy(fsa_dev_ptr[cid].devname, + scsicmd->request->rq_disk->disk_name, + min(sizeof(fsa_dev_ptr[cid].devname), + sizeof(scsicmd->request->rq_disk->disk_name) + 1)); ret = aac_read(scsicmd, cid); spin_lock_irq(host->host_lock); return ret; case WRITE_6: case WRITE_10: + case WRITE_12: + case WRITE_16: spin_unlock_irq(host->host_lock); ret = aac_write(scsicmd, cid); spin_lock_irq(host->host_lock); @@ -1745,6 +1950,8 @@ static void aac_srb_callback(void *context, struct fib * fibptr) case WRITE_10: case READ_12: case WRITE_12: + case READ_16: + case WRITE_16: if(le32_to_cpu(srbreply->data_xfer_length) < scsicmd->underflow ) { printk(KERN_WARNING"aacraid: SCSI CMD underflow\n"); } else { @@ -1850,8 +2057,8 @@ static void aac_srb_callback(void *context, struct fib * fibptr) sizeof(scsicmd->sense_buffer) : le32_to_cpu(srbreply->sense_data_size); #ifdef AAC_DETAILED_STATUS_INFO - dprintk((KERN_WARNING "aac_srb_callback: check condition, status = %d len=%d\n", - le32_to_cpu(srbreply->status), len)); + printk(KERN_WARNING "aac_srb_callback: check condition, status = %d len=%d\n", + le32_to_cpu(srbreply->status), len); #endif memcpy(scsicmd->sense_buffer, srbreply->sense_data, len); diff --git a/drivers/scsi/aacraid/aacraid.h b/drivers/scsi/aacraid/aacraid.h index e40528185d4..4a99d2f000f 100644 --- a/drivers/scsi/aacraid/aacraid.h +++ b/drivers/scsi/aacraid/aacraid.h @@ -1,6 +1,10 @@ #if (!defined(dprintk)) # define dprintk(x) #endif +/* eg: if (nblank(dprintk(x))) */ +#define _nblank(x) #x +#define nblank(x) _nblank(x)[0] + /*------------------------------------------------------------------------------ * D E F I N E S @@ -302,7 +306,6 @@ enum aac_queue_types { */ #define FsaNormal 1 -#define FsaHigh 2 /* * Define the FIB. The FIB is the where all the requested data and @@ -546,8 +549,6 @@ struct aac_queue { /* This is only valid for adapter to host command queues. */ spinlock_t *lock; /* Spinlock for this queue must take this lock before accessing the lock */ spinlock_t lockdata; /* Actual lock (used only on one side of the lock) */ - unsigned long SavedIrql; /* Previous IRQL when the spin lock is taken */ - u32 padding; /* Padding - FIXME - can remove I believe */ struct list_head cmdq; /* A queue of FIBs which need to be prcessed by the FS thread. This is */ /* only valid for command queues which receive entries from the adapter. */ struct list_head pendingq; /* A queue of outstanding fib's to the adapter. */ @@ -776,7 +777,9 @@ struct fsa_dev_info { u64 last; u64 size; u32 type; + u32 config_waiting_on; u16 queue_depth; + u8 config_needed; u8 valid; u8 ro; u8 locked; @@ -1012,6 +1015,7 @@ struct aac_dev /* macro side-effects BEWARE */ # define raw_io_interface \ init->InitStructRevision==cpu_to_le32(ADAPTER_INIT_STRUCT_REVISION_4) + u8 raw_io_64; u8 printf_enabled; }; @@ -1362,8 +1366,10 @@ struct aac_srb_reply #define VM_CtBlockVerify64 18 #define VM_CtHostRead64 19 #define VM_CtHostWrite64 20 +#define VM_DrvErrTblLog 21 +#define VM_NameServe64 22 -#define MAX_VMCOMMAND_NUM 21 /* used for sizing stats array - leave last */ +#define MAX_VMCOMMAND_NUM 23 /* used for sizing stats array - leave last */ /* * Descriptive information (eg, vital stats) @@ -1472,6 +1478,7 @@ struct aac_mntent { manager (eg, filesystem) */ __le32 altoid; /* != oid <==> snapshot or broken mirror exists */ + __le32 capacityhigh; }; #define FSCS_NOTCLEAN 0x0001 /* fsck is neccessary before mounting */ @@ -1707,6 +1714,7 @@ extern struct aac_common aac_config; #define AifCmdJobProgress 2 /* Progress report */ #define AifJobCtrZero 101 /* Array Zero progress */ #define AifJobStsSuccess 1 /* Job completes */ +#define AifJobStsRunning 102 /* Job running */ #define AifCmdAPIReport 3 /* Report from other user of API */ #define AifCmdDriverNotify 4 /* Notify host driver of event */ #define AifDenMorphComplete 200 /* A morph operation completed */ @@ -1777,6 +1785,7 @@ int fib_adapter_complete(struct fib * fibptr, unsigned short size); struct aac_driver_ident* aac_get_driver_ident(int devtype); int aac_get_adapter_info(struct aac_dev* dev); int aac_send_shutdown(struct aac_dev *dev); +int probe_container(struct aac_dev *dev, int cid); extern int numacb; extern int acbsize; extern char aac_driver_version[]; diff --git a/drivers/scsi/aacraid/comminit.c b/drivers/scsi/aacraid/comminit.c index 75abd045328..59a341b2aed 100644 --- a/drivers/scsi/aacraid/comminit.c +++ b/drivers/scsi/aacraid/comminit.c @@ -195,7 +195,7 @@ int aac_send_shutdown(struct aac_dev * dev) fibctx, sizeof(struct aac_close), FsaNormal, - 1, 1, + -2 /* Timeout silently */, 1, NULL, NULL); if (status == 0) @@ -313,8 +313,15 @@ struct aac_dev *aac_init_adapter(struct aac_dev *dev) dev->max_fib_size = sizeof(struct hw_fib); dev->sg_tablesize = host->sg_tablesize = (dev->max_fib_size - sizeof(struct aac_fibhdr) - - sizeof(struct aac_write) + sizeof(struct sgmap)) - / sizeof(struct sgmap); + - sizeof(struct aac_write) + sizeof(struct sgentry)) + / sizeof(struct sgentry); + dev->raw_io_64 = 0; + if ((!aac_adapter_sync_cmd(dev, GET_ADAPTER_PROPERTIES, + 0, 0, 0, 0, 0, 0, status+0, status+1, status+2, NULL, NULL)) && + (status[0] == 0x00000001)) { + if (status[1] & AAC_OPT_NEW_COMM_64) + dev->raw_io_64 = 1; + } if ((!aac_adapter_sync_cmd(dev, GET_COMM_PREFERRED_SETTINGS, 0, 0, 0, 0, 0, 0, status+0, status+1, status+2, status+3, status+4)) @@ -342,8 +349,8 @@ struct aac_dev *aac_init_adapter(struct aac_dev *dev) dev->max_fib_size = 512; dev->sg_tablesize = host->sg_tablesize = (512 - sizeof(struct aac_fibhdr) - - sizeof(struct aac_write) + sizeof(struct sgmap)) - / sizeof(struct sgmap); + - sizeof(struct aac_write) + sizeof(struct sgentry)) + / sizeof(struct sgentry); host->can_queue = AAC_NUM_IO_FIB; } else if (acbsize == 2048) { host->max_sectors = 512; diff --git a/drivers/scsi/aacraid/commsup.c b/drivers/scsi/aacraid/commsup.c index a1d303f0348..e4d543a474a 100644 --- a/drivers/scsi/aacraid/commsup.c +++ b/drivers/scsi/aacraid/commsup.c @@ -39,7 +39,9 @@ #include <linux/completion.h> #include <linux/blkdev.h> #include <scsi/scsi_host.h> +#include <scsi/scsi_device.h> #include <asm/semaphore.h> +#include <asm/delay.h> #include "aacraid.h" @@ -269,40 +271,22 @@ static int aac_get_entry (struct aac_dev * dev, u32 qid, struct aac_entry **entr /* Interrupt Moderation, only interrupt for first two entries */ if (idx != le32_to_cpu(*(q->headers.consumer))) { if (--idx == 0) { - if (qid == AdapHighCmdQueue) - idx = ADAP_HIGH_CMD_ENTRIES; - else if (qid == AdapNormCmdQueue) + if (qid == AdapNormCmdQueue) idx = ADAP_NORM_CMD_ENTRIES; - else if (qid == AdapHighRespQueue) - idx = ADAP_HIGH_RESP_ENTRIES; - else if (qid == AdapNormRespQueue) + else idx = ADAP_NORM_RESP_ENTRIES; } if (idx != le32_to_cpu(*(q->headers.consumer))) *nonotify = 1; } - if (qid == AdapHighCmdQueue) { - if (*index >= ADAP_HIGH_CMD_ENTRIES) - *index = 0; - } else if (qid == AdapNormCmdQueue) { + if (qid == AdapNormCmdQueue) { if (*index >= ADAP_NORM_CMD_ENTRIES) *index = 0; /* Wrap to front of the Producer Queue. */ - } - else if (qid == AdapHighRespQueue) - { - if (*index >= ADAP_HIGH_RESP_ENTRIES) - *index = 0; - } - else if (qid == AdapNormRespQueue) - { + } else { if (*index >= ADAP_NORM_RESP_ENTRIES) *index = 0; /* Wrap to front of the Producer Queue. */ } - else { - printk("aacraid: invalid qid\n"); - BUG(); - } if ((*index + 1) == le32_to_cpu(*(q->headers.consumer))) { /* Queue is full */ printk(KERN_WARNING "Queue %d full, %u outstanding.\n", @@ -334,12 +318,8 @@ static int aac_queue_get(struct aac_dev * dev, u32 * index, u32 qid, struct hw_f { struct aac_entry * entry = NULL; int map = 0; - struct aac_queue * q = &dev->queues->queue[qid]; - - spin_lock_irqsave(q->lock, q->SavedIrql); - if (qid == AdapHighCmdQueue || qid == AdapNormCmdQueue) - { + if (qid == AdapNormCmdQueue) { /* if no entries wait for some if caller wants to */ while (!aac_get_entry(dev, qid, &entry, index, nonotify)) { @@ -350,9 +330,7 @@ static int aac_queue_get(struct aac_dev * dev, u32 * index, u32 qid, struct hw_f */ entry->size = cpu_to_le32(le16_to_cpu(hw_fib->header.Size)); map = 1; - } - else if (qid == AdapHighRespQueue || qid == AdapNormRespQueue) - { + } else { while(!aac_get_entry(dev, qid, &entry, index, nonotify)) { /* if no entries wait for some if caller wants to */ @@ -375,42 +353,6 @@ static int aac_queue_get(struct aac_dev * dev, u32 * index, u32 qid, struct hw_f return 0; } - -/** - * aac_insert_entry - insert a queue entry - * @dev: Adapter - * @index: Index of entry to insert - * @qid: Queue number - * @nonotify: Suppress adapter notification - * - * Gets the next free QE off the requested priorty adapter command - * queue and associates the Fib with the QE. The QE represented by - * index is ready to insert on the queue when this routine returns - * success. - */ - -static int aac_insert_entry(struct aac_dev * dev, u32 index, u32 qid, unsigned long nonotify) -{ - struct aac_queue * q = &dev->queues->queue[qid]; - - if(q == NULL) - BUG(); - *(q->headers.producer) = cpu_to_le32(index + 1); - spin_unlock_irqrestore(q->lock, q->SavedIrql); - - if (qid == AdapHighCmdQueue || - qid == AdapNormCmdQueue || - qid == AdapHighRespQueue || - qid == AdapNormRespQueue) - { - if (!nonotify) - aac_adapter_notify(dev, qid); - } - else - printk("Suprise insert!\n"); - return 0; -} - /* * Define the highest level of host to adapter communication routines. * These routines will support host to adapter FS commuication. These @@ -439,12 +381,13 @@ static int aac_insert_entry(struct aac_dev * dev, u32 index, u32 qid, unsigned l int fib_send(u16 command, struct fib * fibptr, unsigned long size, int priority, int wait, int reply, fib_callback callback, void * callback_data) { u32 index; - u32 qid; struct aac_dev * dev = fibptr->dev; unsigned long nointr = 0; struct hw_fib * hw_fib = fibptr->hw_fib; struct aac_queue * q; unsigned long flags = 0; + unsigned long qflags; + if (!(hw_fib->header.XferState & cpu_to_le32(HostOwned))) return -EBUSY; /* @@ -497,26 +440,8 @@ int fib_send(u16 command, struct fib * fibptr, unsigned long size, int priority * Get a queue entry connect the FIB to it and send an notify * the adapter a command is ready. */ - if (priority == FsaHigh) { - hw_fib->header.XferState |= cpu_to_le32(HighPriority); - qid = AdapHighCmdQueue; - } else { - hw_fib->header.XferState |= cpu_to_le32(NormalPriority); - qid = AdapNormCmdQueue; - } - q = &dev->queues->queue[qid]; + hw_fib->header.XferState |= cpu_to_le32(NormalPriority); - if(wait) - spin_lock_irqsave(&fibptr->event_lock, flags); - if(aac_queue_get( dev, &index, qid, hw_fib, 1, fibptr, &nointr)<0) - return -EWOULDBLOCK; - dprintk((KERN_DEBUG "fib_send: inserting a queue entry at index %d.\n",index)); - dprintk((KERN_DEBUG "Fib contents:.\n")); - dprintk((KERN_DEBUG " Command = %d.\n", hw_fib->header.Command)); - dprintk((KERN_DEBUG " XferState = %x.\n", hw_fib->header.XferState)); - dprintk((KERN_DEBUG " hw_fib va being sent=%p\n",fibptr->hw_fib)); - dprintk((KERN_DEBUG " hw_fib pa being sent=%lx\n",(ulong)fibptr->hw_fib_pa)); - dprintk((KERN_DEBUG " fib being sent=%p\n",fibptr)); /* * Fill in the Callback and CallbackContext if we are not * going to wait. @@ -525,22 +450,67 @@ int fib_send(u16 command, struct fib * fibptr, unsigned long size, int priority fibptr->callback = callback; fibptr->callback_data = callback_data; } - FIB_COUNTER_INCREMENT(aac_config.FibsSent); - list_add_tail(&fibptr->queue, &q->pendingq); - q->numpending++; fibptr->done = 0; fibptr->flags = 0; - if(aac_insert_entry(dev, index, qid, (nointr & aac_config.irq_mod)) < 0) - return -EWOULDBLOCK; + FIB_COUNTER_INCREMENT(aac_config.FibsSent); + + dprintk((KERN_DEBUG "fib_send: inserting a queue entry at index %d.\n",index)); + dprintk((KERN_DEBUG "Fib contents:.\n")); + dprintk((KERN_DEBUG " Command = %d.\n", hw_fib->header.Command)); + dprintk((KERN_DEBUG " XferState = %x.\n", hw_fib->header.XferState)); + dprintk((KERN_DEBUG " hw_fib va being sent=%p\n",fibptr->hw_fib)); + dprintk((KERN_DEBUG " hw_fib pa being sent=%lx\n",(ulong)fibptr->hw_fib_pa)); + dprintk((KERN_DEBUG " fib being sent=%p\n",fibptr)); + + q = &dev->queues->queue[AdapNormCmdQueue]; + + if(wait) + spin_lock_irqsave(&fibptr->event_lock, flags); + spin_lock_irqsave(q->lock, qflags); + aac_queue_get( dev, &index, AdapNormCmdQueue, hw_fib, 1, fibptr, &nointr); + + list_add_tail(&fibptr->queue, &q->pendingq); + q->numpending++; + *(q->headers.producer) = cpu_to_le32(index + 1); + spin_unlock_irqrestore(q->lock, qflags); + if (!(nointr & aac_config.irq_mod)) + aac_adapter_notify(dev, AdapNormCmdQueue); /* * If the caller wanted us to wait for response wait now. */ if (wait) { spin_unlock_irqrestore(&fibptr->event_lock, flags); - down(&fibptr->event_wait); + /* Only set for first known interruptable command */ + if (wait < 0) { + /* + * *VERY* Dangerous to time out a command, the + * assumption is made that we have no hope of + * functioning because an interrupt routing or other + * hardware failure has occurred. + */ + unsigned long count = 36000000L; /* 3 minutes */ + unsigned long qflags; + while (down_trylock(&fibptr->event_wait)) { + if (--count == 0) { + spin_lock_irqsave(q->lock, qflags); + q->numpending--; + list_del(&fibptr->queue); + spin_unlock_irqrestore(q->lock, qflags); + if (wait == -1) { + printk(KERN_ERR "aacraid: fib_send: first asynchronous command timed out.\n" + "Usually a result of a PCI interrupt routing problem;\n" + "update mother board BIOS or consider utilizing one of\n" + "the SAFE mode kernel options (acpi, apic etc)\n"); + } + return -ETIMEDOUT; + } + udelay(5); + } + } else + down(&fibptr->event_wait); if(fibptr->done == 0) BUG(); @@ -622,15 +592,9 @@ void aac_consumer_free(struct aac_dev * dev, struct aac_queue *q, u32 qid) case HostNormCmdQueue: notify = HostNormCmdNotFull; break; - case HostHighCmdQueue: - notify = HostHighCmdNotFull; - break; case HostNormRespQueue: notify = HostNormRespNotFull; break; - case HostHighRespQueue: - notify = HostHighRespNotFull; - break; default: BUG(); return; @@ -652,9 +616,13 @@ int fib_adapter_complete(struct fib * fibptr, unsigned short size) { struct hw_fib * hw_fib = fibptr->hw_fib; struct aac_dev * dev = fibptr->dev; + struct aac_queue * q; unsigned long nointr = 0; - if (hw_fib->header.XferState == 0) + unsigned long qflags; + + if (hw_fib->header.XferState == 0) { return 0; + } /* * If we plan to do anything check the structure type first. */ @@ -669,37 +637,21 @@ int fib_adapter_complete(struct fib * fibptr, unsigned short size) * send the completed cdb to the adapter. */ if (hw_fib->header.XferState & cpu_to_le32(SentFromAdapter)) { + u32 index; hw_fib->header.XferState |= cpu_to_le32(HostProcessed); - if (hw_fib->header.XferState & cpu_to_le32(HighPriority)) { - u32 index; - if (size) - { - size += sizeof(struct aac_fibhdr); - if (size > le16_to_cpu(hw_fib->header.SenderSize)) - return -EMSGSIZE; - hw_fib->header.Size = cpu_to_le16(size); - } - if(aac_queue_get(dev, &index, AdapHighRespQueue, hw_fib, 1, NULL, &nointr) < 0) { - return -EWOULDBLOCK; - } - if (aac_insert_entry(dev, index, AdapHighRespQueue, (nointr & (int)aac_config.irq_mod)) != 0) { - } - } else if (hw_fib->header.XferState & - cpu_to_le32(NormalPriority)) { - u32 index; - - if (size) { - size += sizeof(struct aac_fibhdr); - if (size > le16_to_cpu(hw_fib->header.SenderSize)) - return -EMSGSIZE; - hw_fib->header.Size = cpu_to_le16(size); - } - if (aac_queue_get(dev, &index, AdapNormRespQueue, hw_fib, 1, NULL, &nointr) < 0) - return -EWOULDBLOCK; - if (aac_insert_entry(dev, index, AdapNormRespQueue, (nointr & (int)aac_config.irq_mod)) != 0) - { - } + if (size) { + size += sizeof(struct aac_fibhdr); + if (size > le16_to_cpu(hw_fib->header.SenderSize)) + return -EMSGSIZE; + hw_fib->header.Size = cpu_to_le16(size); } + q = &dev->queues->queue[AdapNormRespQueue]; + spin_lock_irqsave(q->lock, qflags); + aac_queue_get(dev, &index, AdapNormRespQueue, hw_fib, 1, NULL, &nointr); + *(q->headers.producer) = cpu_to_le32(index + 1); + spin_unlock_irqrestore(q->lock, qflags); + if (!(nointr & (int)aac_config.irq_mod)) + aac_adapter_notify(dev, AdapNormRespQueue); } else { @@ -791,6 +743,268 @@ void aac_printf(struct aac_dev *dev, u32 val) memset(cp, 0, 256); } + +/** + * aac_handle_aif - Handle a message from the firmware + * @dev: Which adapter this fib is from + * @fibptr: Pointer to fibptr from adapter + * + * This routine handles a driver notify fib from the adapter and + * dispatches it to the appropriate routine for handling. + */ + +static void aac_handle_aif(struct aac_dev * dev, struct fib * fibptr) +{ + struct hw_fib * hw_fib = fibptr->hw_fib; + struct aac_aifcmd * aifcmd = (struct aac_aifcmd *)hw_fib->data; + int busy; + u32 container; + struct scsi_device *device; + enum { + NOTHING, + DELETE, + ADD, + CHANGE + } device_config_needed; + + /* Sniff for container changes */ + + if (!dev) + return; + container = (u32)-1; + + /* + * We have set this up to try and minimize the number of + * re-configures that take place. As a result of this when + * certain AIF's come in we will set a flag waiting for another + * type of AIF before setting the re-config flag. + */ + switch (le32_to_cpu(aifcmd->command)) { + case AifCmdDriverNotify: + switch (le32_to_cpu(((u32 *)aifcmd->data)[0])) { + /* + * Morph or Expand complete + */ + case AifDenMorphComplete: + case AifDenVolumeExtendComplete: + container = le32_to_cpu(((u32 *)aifcmd->data)[1]); + if (container >= dev->maximum_num_containers) + break; + + /* + * Find the Scsi_Device associated with the SCSI + * address. Make sure we have the right array, and if + * so set the flag to initiate a new re-config once we + * see an AifEnConfigChange AIF come through. + */ + + if ((dev != NULL) && (dev->scsi_host_ptr != NULL)) { + device = scsi_device_lookup(dev->scsi_host_ptr, + CONTAINER_TO_CHANNEL(container), + CONTAINER_TO_ID(container), + CONTAINER_TO_LUN(container)); + if (device) { + dev->fsa_dev[container].config_needed = CHANGE; + dev->fsa_dev[container].config_waiting_on = AifEnConfigChange; + scsi_device_put(device); + } + } + } + + /* + * If we are waiting on something and this happens to be + * that thing then set the re-configure flag. + */ + if (container != (u32)-1) { + if (container >= dev->maximum_num_containers) + break; + if (dev->fsa_dev[container].config_waiting_on == + le32_to_cpu(*(u32 *)aifcmd->data)) + dev->fsa_dev[container].config_waiting_on = 0; + } else for (container = 0; + container < dev->maximum_num_containers; ++container) { + if (dev->fsa_dev[container].config_waiting_on == + le32_to_cpu(*(u32 *)aifcmd->data)) + dev->fsa_dev[container].config_waiting_on = 0; + } + break; + + case AifCmdEventNotify: + switch (le32_to_cpu(((u32 *)aifcmd->data)[0])) { + /* + * Add an Array. + */ + case AifEnAddContainer: + container = le32_to_cpu(((u32 *)aifcmd->data)[1]); + if (container >= dev->maximum_num_containers) + break; + dev->fsa_dev[container].config_needed = ADD; + dev->fsa_dev[container].config_waiting_on = + AifEnConfigChange; + break; + + /* + * Delete an Array. + */ + case AifEnDeleteContainer: + container = le32_to_cpu(((u32 *)aifcmd->data)[1]); + if (container >= dev->maximum_num_containers) + break; + dev->fsa_dev[container].config_needed = DELETE; + dev->fsa_dev[container].config_waiting_on = + AifEnConfigChange; + break; + + /* + * Container change detected. If we currently are not + * waiting on something else, setup to wait on a Config Change. + */ + case AifEnContainerChange: + container = le32_to_cpu(((u32 *)aifcmd->data)[1]); + if (container >= dev->maximum_num_containers) + break; + if (dev->fsa_dev[container].config_waiting_on) + break; + dev->fsa_dev[container].config_needed = CHANGE; + dev->fsa_dev[container].config_waiting_on = + AifEnConfigChange; + break; + + case AifEnConfigChange: + break; + + } + + /* + * If we are waiting on something and this happens to be + * that thing then set the re-configure flag. + */ + if (container != (u32)-1) { + if (container >= dev->maximum_num_containers) + break; + if (dev->fsa_dev[container].config_waiting_on == + le32_to_cpu(*(u32 *)aifcmd->data)) + dev->fsa_dev[container].config_waiting_on = 0; + } else for (container = 0; + container < dev->maximum_num_containers; ++container) { + if (dev->fsa_dev[container].config_waiting_on == + le32_to_cpu(*(u32 *)aifcmd->data)) + dev->fsa_dev[container].config_waiting_on = 0; + } + break; + + case AifCmdJobProgress: + /* + * These are job progress AIF's. When a Clear is being + * done on a container it is initially created then hidden from + * the OS. When the clear completes we don't get a config + * change so we monitor the job status complete on a clear then + * wait for a container change. + */ + + if ((((u32 *)aifcmd->data)[1] == cpu_to_le32(AifJobCtrZero)) + && ((((u32 *)aifcmd->data)[6] == ((u32 *)aifcmd->data)[5]) + || (((u32 *)aifcmd->data)[4] == cpu_to_le32(AifJobStsSuccess)))) { + for (container = 0; + container < dev->maximum_num_containers; + ++container) { + /* + * Stomp on all config sequencing for all + * containers? + */ + dev->fsa_dev[container].config_waiting_on = + AifEnContainerChange; + dev->fsa_dev[container].config_needed = ADD; + } + } + if ((((u32 *)aifcmd->data)[1] == cpu_to_le32(AifJobCtrZero)) + && (((u32 *)aifcmd->data)[6] == 0) + && (((u32 *)aifcmd->data)[4] == cpu_to_le32(AifJobStsRunning))) { + for (container = 0; + container < dev->maximum_num_containers; + ++container) { + /* + * Stomp on all config sequencing for all + * containers? + */ + dev->fsa_dev[container].config_waiting_on = + AifEnContainerChange; + dev->fsa_dev[container].config_needed = DELETE; + } + } + break; + } + + device_config_needed = NOTHING; + for (container = 0; container < dev->maximum_num_containers; + ++container) { + if ((dev->fsa_dev[container].config_waiting_on == 0) + && (dev->fsa_dev[container].config_needed != NOTHING)) { + device_config_needed = + dev->fsa_dev[container].config_needed; + dev->fsa_dev[container].config_needed = NOTHING; + break; + } + } + if (device_config_needed == NOTHING) + return; + + /* + * If we decided that a re-configuration needs to be done, + * schedule it here on the way out the door, please close the door + * behind you. + */ + + busy = 0; + + + /* + * Find the Scsi_Device associated with the SCSI address, + * and mark it as changed, invalidating the cache. This deals + * with changes to existing device IDs. + */ + + if (!dev || !dev->scsi_host_ptr) + return; + /* + * force reload of disk info via probe_container + */ + if ((device_config_needed == CHANGE) + && (dev->fsa_dev[container].valid == 1)) + dev->fsa_dev[container].valid = 2; + if ((device_config_needed == CHANGE) || + (device_config_needed == ADD)) + probe_container(dev, container); + device = scsi_device_lookup(dev->scsi_host_ptr, + CONTAINER_TO_CHANNEL(container), + CONTAINER_TO_ID(container), + CONTAINER_TO_LUN(container)); + if (device) { + switch (device_config_needed) { + case DELETE: + scsi_remove_device(device); + break; + case CHANGE: + if (!dev->fsa_dev[container].valid) { + scsi_remove_device(device); + break; + } + scsi_rescan_device(&device->sdev_gendev); + + default: + break; + } + scsi_device_put(device); + } + if (device_config_needed == ADD) { + scsi_add_device(dev->scsi_host_ptr, + CONTAINER_TO_CHANNEL(container), + CONTAINER_TO_ID(container), + CONTAINER_TO_LUN(container)); + } + +} + /** * aac_command_thread - command processing thread * @dev: Adapter to monitor @@ -805,7 +1019,6 @@ int aac_command_thread(struct aac_dev * dev) { struct hw_fib *hw_fib, *hw_newfib; struct fib *fib, *newfib; - struct aac_queue_block *queues = dev->queues; struct aac_fib_context *fibctx; unsigned long flags; DECLARE_WAITQUEUE(wait, current); @@ -825,21 +1038,22 @@ int aac_command_thread(struct aac_dev * dev) * Let the DPC know it has a place to send the AIF's to. */ dev->aif_thread = 1; - add_wait_queue(&queues->queue[HostNormCmdQueue].cmdready, &wait); + add_wait_queue(&dev->queues->queue[HostNormCmdQueue].cmdready, &wait); set_current_state(TASK_INTERRUPTIBLE); + dprintk ((KERN_INFO "aac_command_thread start\n")); while(1) { - spin_lock_irqsave(queues->queue[HostNormCmdQueue].lock, flags); - while(!list_empty(&(queues->queue[HostNormCmdQueue].cmdq))) { + spin_lock_irqsave(dev->queues->queue[HostNormCmdQueue].lock, flags); + while(!list_empty(&(dev->queues->queue[HostNormCmdQueue].cmdq))) { struct list_head *entry; struct aac_aifcmd * aifcmd; set_current_state(TASK_RUNNING); - - entry = queues->queue[HostNormCmdQueue].cmdq.next; + + entry = dev->queues->queue[HostNormCmdQueue].cmdq.next; list_del(entry); - - spin_unlock_irqrestore(queues->queue[HostNormCmdQueue].lock, flags); + + spin_unlock_irqrestore(dev->queues->queue[HostNormCmdQueue].lock, flags); fib = list_entry(entry, struct fib, fiblink); /* * We will process the FIB here or pass it to a @@ -860,6 +1074,7 @@ int aac_command_thread(struct aac_dev * dev) aifcmd = (struct aac_aifcmd *) hw_fib->data; if (aifcmd->command == cpu_to_le32(AifCmdDriverNotify)) { /* Handle Driver Notify Events */ + aac_handle_aif(dev, fib); *(__le32 *)hw_fib->data = cpu_to_le32(ST_OK); fib_adapter_complete(fib, (u16)sizeof(u32)); } else { @@ -869,9 +1084,62 @@ int aac_command_thread(struct aac_dev * dev) u32 time_now, time_last; unsigned long flagv; - + unsigned num; + struct hw_fib ** hw_fib_pool, ** hw_fib_p; + struct fib ** fib_pool, ** fib_p; + + /* Sniff events */ + if ((aifcmd->command == + cpu_to_le32(AifCmdEventNotify)) || + (aifcmd->command == + cpu_to_le32(AifCmdJobProgress))) { + aac_handle_aif(dev, fib); + } + time_now = jiffies/HZ; + /* + * Warning: no sleep allowed while + * holding spinlock. We take the estimate + * and pre-allocate a set of fibs outside the + * lock. + */ + num = le32_to_cpu(dev->init->AdapterFibsSize) + / sizeof(struct hw_fib); /* some extra */ + spin_lock_irqsave(&dev->fib_lock, flagv); + entry = dev->fib_list.next; + while (entry != &dev->fib_list) { + entry = entry->next; + ++num; + } + spin_unlock_irqrestore(&dev->fib_lock, flagv); + hw_fib_pool = NULL; + fib_pool = NULL; + if (num + && ((hw_fib_pool = kmalloc(sizeof(struct hw_fib *) * num, GFP_KERNEL))) + && ((fib_pool = kmalloc(sizeof(struct fib *) * num, GFP_KERNEL)))) { + hw_fib_p = hw_fib_pool; + fib_p = fib_pool; + while (hw_fib_p < &hw_fib_pool[num]) { + if (!(*(hw_fib_p++) = kmalloc(sizeof(struct hw_fib), GFP_KERNEL))) { + --hw_fib_p; + break; + } + if (!(*(fib_p++) = kmalloc(sizeof(struct fib), GFP_KERNEL))) { + kfree(*(--hw_fib_p)); + break; + } + } + if ((num = hw_fib_p - hw_fib_pool) == 0) { + kfree(fib_pool); + fib_pool = NULL; + kfree(hw_fib_pool); + hw_fib_pool = NULL; + } + } else if (hw_fib_pool) { + kfree(hw_fib_pool); + hw_fib_pool = NULL; + } spin_lock_irqsave(&dev->fib_lock, flagv); entry = dev->fib_list.next; /* @@ -880,6 +1148,8 @@ int aac_command_thread(struct aac_dev * dev) * fib, and then set the event to wake up the * thread that is waiting for it. */ + hw_fib_p = hw_fib_pool; + fib_p = fib_pool; while (entry != &dev->fib_list) { /* * Extract the fibctx @@ -912,9 +1182,11 @@ int aac_command_thread(struct aac_dev * dev) * Warning: no sleep allowed while * holding spinlock */ - hw_newfib = kmalloc(sizeof(struct hw_fib), GFP_ATOMIC); - newfib = kmalloc(sizeof(struct fib), GFP_ATOMIC); - if (newfib && hw_newfib) { + if (hw_fib_p < &hw_fib_pool[num]) { + hw_newfib = *hw_fib_p; + *(hw_fib_p++) = NULL; + newfib = *fib_p; + *(fib_p++) = NULL; /* * Make the copy of the FIB */ @@ -929,15 +1201,11 @@ int aac_command_thread(struct aac_dev * dev) fibctx->count++; /* * Set the event to wake up the - * thread that will waiting. + * thread that is waiting. */ up(&fibctx->wait_sem); } else { printk(KERN_WARNING "aifd: didn't allocate NewFib.\n"); - if(newfib) - kfree(newfib); - if(hw_newfib) - kfree(hw_newfib); } entry = entry->next; } @@ -947,21 +1215,38 @@ int aac_command_thread(struct aac_dev * dev) *(__le32 *)hw_fib->data = cpu_to_le32(ST_OK); fib_adapter_complete(fib, sizeof(u32)); spin_unlock_irqrestore(&dev->fib_lock, flagv); + /* Free up the remaining resources */ + hw_fib_p = hw_fib_pool; + fib_p = fib_pool; + while (hw_fib_p < &hw_fib_pool[num]) { + if (*hw_fib_p) + kfree(*hw_fib_p); + if (*fib_p) + kfree(*fib_p); + ++fib_p; + ++hw_fib_p; + } + if (hw_fib_pool) + kfree(hw_fib_pool); + if (fib_pool) + kfree(fib_pool); } - spin_lock_irqsave(queues->queue[HostNormCmdQueue].lock, flags); kfree(fib); + spin_lock_irqsave(dev->queues->queue[HostNormCmdQueue].lock, flags); } /* * There are no more AIF's */ - spin_unlock_irqrestore(queues->queue[HostNormCmdQueue].lock, flags); + spin_unlock_irqrestore(dev->queues->queue[HostNormCmdQueue].lock, flags); schedule(); if(signal_pending(current)) break; set_current_state(TASK_INTERRUPTIBLE); } - remove_wait_queue(&queues->queue[HostNormCmdQueue].cmdready, &wait); + if (dev->queues) + remove_wait_queue(&dev->queues->queue[HostNormCmdQueue].cmdready, &wait); dev->aif_thread = 0; complete_and_exit(&dev->aif_completion, 0); + return 0; } diff --git a/drivers/scsi/aacraid/linit.c b/drivers/scsi/aacraid/linit.c index 4ff29d7f582..de8490a9283 100644 --- a/drivers/scsi/aacraid/linit.c +++ b/drivers/scsi/aacraid/linit.c @@ -748,7 +748,8 @@ static int __devinit aac_probe_one(struct pci_dev *pdev, unique_id++; } - if (pci_enable_device(pdev)) + error = pci_enable_device(pdev); + if (error) goto out; if (pci_set_dma_mask(pdev, 0xFFFFFFFFULL) || @@ -772,6 +773,7 @@ static int __devinit aac_probe_one(struct pci_dev *pdev, shost->irq = pdev->irq; shost->base = pci_resource_start(pdev, 0); shost->unique_id = unique_id; + shost->max_cmd_len = 16; aac = (struct aac_dev *)shost->hostdata; aac->scsi_host_ptr = shost; @@ -799,7 +801,9 @@ static int __devinit aac_probe_one(struct pci_dev *pdev, goto out_free_fibs; aac->maximum_num_channels = aac_drivers[index].channels; - aac_get_adapter_info(aac); + error = aac_get_adapter_info(aac); + if (error < 0) + goto out_deinit; /* * Lets override negotiations and drop the maximum SG limit to 34 @@ -927,8 +931,8 @@ static int __init aac_init(void) printk(KERN_INFO "Adaptec %s driver (%s)\n", AAC_DRIVERNAME, aac_driver_version); - error = pci_module_init(&aac_pci_driver); - if (error) + error = pci_register_driver(&aac_pci_driver); + if (error < 0) return error; aac_cfg_major = register_chrdev( 0, "aac", &aac_cfg_fops); diff --git a/drivers/scsi/aic7xxx/aic7770_osm.c b/drivers/scsi/aic7xxx/aic7770_osm.c index 70c5fb59c9e..d754b326786 100644 --- a/drivers/scsi/aic7xxx/aic7770_osm.c +++ b/drivers/scsi/aic7xxx/aic7770_osm.c @@ -112,6 +112,9 @@ aic7770_remove(struct device *dev) struct ahc_softc *ahc = dev_get_drvdata(dev); u_long s; + if (ahc->platform_data && ahc->platform_data->host) + scsi_remove_host(ahc->platform_data->host); + ahc_lock(ahc, &s); ahc_intr_enable(ahc, FALSE); ahc_unlock(ahc, &s); diff --git a/drivers/scsi/aic7xxx/aic79xx_osm.c b/drivers/scsi/aic7xxx/aic79xx_osm.c index 6b6d4e28779..95c285cc83e 100644 --- a/drivers/scsi/aic7xxx/aic79xx_osm.c +++ b/drivers/scsi/aic7xxx/aic79xx_osm.c @@ -1192,11 +1192,6 @@ ahd_platform_free(struct ahd_softc *ahd) int i, j; if (ahd->platform_data != NULL) { - if (ahd->platform_data->host != NULL) { - scsi_remove_host(ahd->platform_data->host); - scsi_host_put(ahd->platform_data->host); - } - /* destroy all of the device and target objects */ for (i = 0; i < AHD_NUM_TARGETS; i++) { starget = ahd->platform_data->starget[i]; @@ -1226,6 +1221,9 @@ ahd_platform_free(struct ahd_softc *ahd) release_mem_region(ahd->platform_data->mem_busaddr, 0x1000); } + if (ahd->platform_data->host) + scsi_host_put(ahd->platform_data->host); + free(ahd->platform_data, M_DEVBUF); } } diff --git a/drivers/scsi/aic7xxx/aic79xx_osm_pci.c b/drivers/scsi/aic7xxx/aic79xx_osm_pci.c index 390b53852d4..bf360ae021a 100644 --- a/drivers/scsi/aic7xxx/aic79xx_osm_pci.c +++ b/drivers/scsi/aic7xxx/aic79xx_osm_pci.c @@ -95,6 +95,9 @@ ahd_linux_pci_dev_remove(struct pci_dev *pdev) struct ahd_softc *ahd = pci_get_drvdata(pdev); u_long s; + if (ahd->platform_data && ahd->platform_data->host) + scsi_remove_host(ahd->platform_data->host); + ahd_lock(ahd, &s); ahd_intr_enable(ahd, FALSE); ahd_unlock(ahd, &s); diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm.c b/drivers/scsi/aic7xxx/aic7xxx_osm.c index 876d1de8480..6ee1435d37f 100644 --- a/drivers/scsi/aic7xxx/aic7xxx_osm.c +++ b/drivers/scsi/aic7xxx/aic7xxx_osm.c @@ -1209,11 +1209,6 @@ ahc_platform_free(struct ahc_softc *ahc) int i, j; if (ahc->platform_data != NULL) { - if (ahc->platform_data->host != NULL) { - scsi_remove_host(ahc->platform_data->host); - scsi_host_put(ahc->platform_data->host); - } - /* destroy all of the device and target objects */ for (i = 0; i < AHC_NUM_TARGETS; i++) { starget = ahc->platform_data->starget[i]; @@ -1242,6 +1237,9 @@ ahc_platform_free(struct ahc_softc *ahc) 0x1000); } + if (ahc->platform_data->host) + scsi_host_put(ahc->platform_data->host); + free(ahc->platform_data, M_DEVBUF); } } diff --git a/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c b/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c index 3ce77ddc889..cb30d9c1153 100644 --- a/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c +++ b/drivers/scsi/aic7xxx/aic7xxx_osm_pci.c @@ -143,6 +143,9 @@ ahc_linux_pci_dev_remove(struct pci_dev *pdev) struct ahc_softc *ahc = pci_get_drvdata(pdev); u_long s; + if (ahc->platform_data && ahc->platform_data->host) + scsi_remove_host(ahc->platform_data->host); + ahc_lock(ahc, &s); ahc_intr_enable(ahc, FALSE); ahc_unlock(ahc, &s); diff --git a/drivers/scsi/hosts.c b/drivers/scsi/hosts.c index f2a72d33132..02fe371b0ab 100644 --- a/drivers/scsi/hosts.c +++ b/drivers/scsi/hosts.c @@ -176,6 +176,7 @@ void scsi_remove_host(struct Scsi_Host *shost) transport_unregister_device(&shost->shost_gendev); class_device_unregister(&shost->shost_classdev); device_del(&shost->shost_gendev); + scsi_proc_hostdir_rm(shost->hostt); } EXPORT_SYMBOL(scsi_remove_host); @@ -262,7 +263,6 @@ static void scsi_host_dev_release(struct device *dev) if (shost->work_q) destroy_workqueue(shost->work_q); - scsi_proc_hostdir_rm(shost->hostt); scsi_destroy_command_freelist(shost); kfree(shost->shost_data); diff --git a/drivers/scsi/lpfc/lpfc_attr.c b/drivers/scsi/lpfc/lpfc_attr.c index 86eaf6d408d..acae7c48ef7 100644 --- a/drivers/scsi/lpfc/lpfc_attr.c +++ b/drivers/scsi/lpfc/lpfc_attr.c @@ -973,10 +973,10 @@ lpfc_get_host_fabric_name (struct Scsi_Host *shost) if ((phba->fc_flag & FC_FABRIC) || ((phba->fc_topology == TOPOLOGY_LOOP) && (phba->fc_flag & FC_PUBLIC_LOOP))) - node_name = wwn_to_u64(phba->fc_fabparam.nodeName.wwn); + node_name = wwn_to_u64(phba->fc_fabparam.nodeName.u.wwn); else /* fabric is local port if there is no F/FL_Port */ - node_name = wwn_to_u64(phba->fc_nodename.wwn); + node_name = wwn_to_u64(phba->fc_nodename.u.wwn); spin_unlock_irq(shost->host_lock); @@ -1110,7 +1110,7 @@ lpfc_get_starget_node_name(struct scsi_target *starget) /* Search the mapped list for this target ID */ list_for_each_entry(ndlp, &phba->fc_nlpmap_list, nlp_listp) { if (starget->id == ndlp->nlp_sid) { - node_name = wwn_to_u64(ndlp->nlp_nodename.wwn); + node_name = wwn_to_u64(ndlp->nlp_nodename.u.wwn); break; } } @@ -1131,7 +1131,7 @@ lpfc_get_starget_port_name(struct scsi_target *starget) /* Search the mapped list for this target ID */ list_for_each_entry(ndlp, &phba->fc_nlpmap_list, nlp_listp) { if (starget->id == ndlp->nlp_sid) { - port_name = wwn_to_u64(ndlp->nlp_portname.wwn); + port_name = wwn_to_u64(ndlp->nlp_portname.u.wwn); break; } } diff --git a/drivers/scsi/lpfc/lpfc_hbadisc.c b/drivers/scsi/lpfc/lpfc_hbadisc.c index 4fb8eb0c84c..56052f4510c 100644 --- a/drivers/scsi/lpfc/lpfc_hbadisc.c +++ b/drivers/scsi/lpfc/lpfc_hbadisc.c @@ -1019,8 +1019,8 @@ lpfc_register_remote_port(struct lpfc_hba * phba, struct fc_rport_identifiers rport_ids; /* Remote port has reappeared. Re-register w/ FC transport */ - rport_ids.node_name = wwn_to_u64(ndlp->nlp_nodename.wwn); - rport_ids.port_name = wwn_to_u64(ndlp->nlp_portname.wwn); + rport_ids.node_name = wwn_to_u64(ndlp->nlp_nodename.u.wwn); + rport_ids.port_name = wwn_to_u64(ndlp->nlp_portname.u.wwn); rport_ids.port_id = ndlp->nlp_DID; rport_ids.roles = FC_RPORT_ROLE_UNKNOWN; if (ndlp->nlp_type & NLP_FCP_TARGET) diff --git a/drivers/scsi/lpfc/lpfc_hw.h b/drivers/scsi/lpfc/lpfc_hw.h index 047a87c26cc..86c41981188 100644 --- a/drivers/scsi/lpfc/lpfc_hw.h +++ b/drivers/scsi/lpfc/lpfc_hw.h @@ -280,9 +280,9 @@ struct lpfc_name { #define NAME_CCITT_GR_TYPE 0xE uint8_t IEEEextLsb; /* FC Word 0, bit 16:23, IEEE extended Lsb */ uint8_t IEEE[6]; /* FC IEEE address */ - }; + } s; uint8_t wwn[8]; - }; + } u; }; struct csp { diff --git a/drivers/scsi/lpfc/lpfc_init.c b/drivers/scsi/lpfc/lpfc_init.c index 454058f655d..0856ff7d3b3 100644 --- a/drivers/scsi/lpfc/lpfc_init.c +++ b/drivers/scsi/lpfc/lpfc_init.c @@ -285,7 +285,7 @@ lpfc_config_port_post(struct lpfc_hba * phba) if (phba->SerialNumber[0] == 0) { uint8_t *outptr; - outptr = (uint8_t *) & phba->fc_nodename.IEEE[0]; + outptr = &phba->fc_nodename.u.s.IEEE[0]; for (i = 0; i < 12; i++) { status = *outptr++; j = ((status & 0xf0) >> 4); @@ -1523,8 +1523,8 @@ lpfc_pci_probe_one(struct pci_dev *pdev, const struct pci_device_id *pid) * Must done after lpfc_sli_hba_setup() */ - fc_host_node_name(host) = wwn_to_u64(phba->fc_nodename.wwn); - fc_host_port_name(host) = wwn_to_u64(phba->fc_portname.wwn); + fc_host_node_name(host) = wwn_to_u64(phba->fc_nodename.u.wwn); + fc_host_port_name(host) = wwn_to_u64(phba->fc_portname.u.wwn); fc_host_supported_classes(host) = FC_COS_CLASS3; memset(fc_host_supported_fc4s(host), 0, diff --git a/drivers/scsi/megaraid.c b/drivers/scsi/megaraid.c index 6f308ebe3e7..61a6fd810bb 100644 --- a/drivers/scsi/megaraid.c +++ b/drivers/scsi/megaraid.c @@ -621,8 +621,6 @@ mega_build_cmd(adapter_t *adapter, Scsi_Cmnd *cmd, int *busy) if(islogical) { switch (cmd->cmnd[0]) { case TEST_UNIT_READY: - memset(cmd->request_buffer, 0, cmd->request_bufflen); - #if MEGA_HAVE_CLUSTERING /* * Do we support clustering and is the support enabled @@ -652,11 +650,28 @@ mega_build_cmd(adapter_t *adapter, Scsi_Cmnd *cmd, int *busy) return NULL; #endif - case MODE_SENSE: + case MODE_SENSE: { + char *buf; + + if (cmd->use_sg) { + struct scatterlist *sg; + + sg = (struct scatterlist *)cmd->request_buffer; + buf = kmap_atomic(sg->page, KM_IRQ0) + + sg->offset; + } else + buf = cmd->request_buffer; memset(cmd->request_buffer, 0, cmd->cmnd[4]); + if (cmd->use_sg) { + struct scatterlist *sg; + + sg = (struct scatterlist *)cmd->request_buffer; + kunmap_atomic(buf - sg->offset, KM_IRQ0); + } cmd->result = (DID_OK << 16); cmd->scsi_done(cmd); return NULL; + } case READ_CAPACITY: case INQUIRY: @@ -1685,14 +1700,23 @@ mega_rundoneq (adapter_t *adapter) static void mega_free_scb(adapter_t *adapter, scb_t *scb) { + unsigned long length; + switch( scb->dma_type ) { case MEGA_DMA_TYPE_NONE: break; case MEGA_BULK_DATA: + if (scb->cmd->use_sg == 0) + length = scb->cmd->request_bufflen; + else { + struct scatterlist *sgl = + (struct scatterlist *)scb->cmd->request_buffer; + length = sgl->length; + } pci_unmap_page(adapter->dev, scb->dma_h_bulkdata, - scb->cmd->request_bufflen, scb->dma_direction); + length, scb->dma_direction); break; case MEGA_SGLIST: @@ -1741,6 +1765,7 @@ mega_build_sglist(adapter_t *adapter, scb_t *scb, u32 *buf, u32 *len) struct scatterlist *sgl; struct page *page; unsigned long offset; + unsigned int length; Scsi_Cmnd *cmd; int sgcnt; int idx; @@ -1748,14 +1773,23 @@ mega_build_sglist(adapter_t *adapter, scb_t *scb, u32 *buf, u32 *len) cmd = scb->cmd; /* Scatter-gather not used */ - if( !cmd->use_sg ) { - - page = virt_to_page(cmd->request_buffer); - offset = offset_in_page(cmd->request_buffer); + if( cmd->use_sg == 0 || (cmd->use_sg == 1 && + !adapter->has_64bit_addr)) { + + if (cmd->use_sg == 0) { + page = virt_to_page(cmd->request_buffer); + offset = offset_in_page(cmd->request_buffer); + length = cmd->request_bufflen; + } else { + sgl = (struct scatterlist *)cmd->request_buffer; + page = sgl->page; + offset = sgl->offset; + length = sgl->length; + } scb->dma_h_bulkdata = pci_map_page(adapter->dev, page, offset, - cmd->request_bufflen, + length, scb->dma_direction); scb->dma_type = MEGA_BULK_DATA; @@ -1765,14 +1799,14 @@ mega_build_sglist(adapter_t *adapter, scb_t *scb, u32 *buf, u32 *len) */ if( adapter->has_64bit_addr ) { scb->sgl64[0].address = scb->dma_h_bulkdata; - scb->sgl64[0].length = cmd->request_bufflen; + scb->sgl64[0].length = length; *buf = (u32)scb->sgl_dma_addr; - *len = (u32)cmd->request_bufflen; + *len = (u32)length; return 1; } else { *buf = (u32)scb->dma_h_bulkdata; - *len = (u32)cmd->request_bufflen; + *len = (u32)length; } return 0; } @@ -1791,27 +1825,23 @@ mega_build_sglist(adapter_t *adapter, scb_t *scb, u32 *buf, u32 *len) if( sgcnt > adapter->sglen ) BUG(); + *len = 0; + for( idx = 0; idx < sgcnt; idx++, sgl++ ) { if( adapter->has_64bit_addr ) { scb->sgl64[idx].address = sg_dma_address(sgl); - scb->sgl64[idx].length = sg_dma_len(sgl); + *len += scb->sgl64[idx].length = sg_dma_len(sgl); } else { scb->sgl[idx].address = sg_dma_address(sgl); - scb->sgl[idx].length = sg_dma_len(sgl); + *len += scb->sgl[idx].length = sg_dma_len(sgl); } } /* Reset pointer and length fields */ *buf = scb->sgl_dma_addr; - /* - * For passthru command, dataxferlen must be set, even for commands - * with a sg list - */ - *len = (u32)cmd->request_bufflen; - /* Return count of SG requests */ return sgcnt; } diff --git a/drivers/scsi/megaraid/Kconfig.megaraid b/drivers/scsi/megaraid/Kconfig.megaraid index 917d591d90b..7363e12663a 100644 --- a/drivers/scsi/megaraid/Kconfig.megaraid +++ b/drivers/scsi/megaraid/Kconfig.megaraid @@ -76,3 +76,12 @@ config MEGARAID_LEGACY To compile this driver as a module, choose M here: the module will be called megaraid endif + +config MEGARAID_SAS + tristate "LSI Logic MegaRAID SAS RAID Module" + depends on PCI && SCSI + help + Module for LSI Logic's SAS based RAID controllers. + To compile this driver as a module, choose 'm' here. + Module will be called megaraid_sas + diff --git a/drivers/scsi/megaraid/Makefile b/drivers/scsi/megaraid/Makefile index 6dd99f27572..f469915b97c 100644 --- a/drivers/scsi/megaraid/Makefile +++ b/drivers/scsi/megaraid/Makefile @@ -1,2 +1,3 @@ obj-$(CONFIG_MEGARAID_MM) += megaraid_mm.o obj-$(CONFIG_MEGARAID_MAILBOX) += megaraid_mbox.o +obj-$(CONFIG_MEGARAID_SAS) += megaraid_sas.o diff --git a/drivers/scsi/megaraid/megaraid_sas.c b/drivers/scsi/megaraid/megaraid_sas.c new file mode 100644 index 00000000000..c3f63739573 --- /dev/null +++ b/drivers/scsi/megaraid/megaraid_sas.c @@ -0,0 +1,2806 @@ +/* + * + * Linux MegaRAID driver for SAS based RAID controllers + * + * Copyright (c) 2003-2005 LSI Logic Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * FILE : megaraid_sas.c + * Version : v00.00.02.00-rc4 + * + * Authors: + * Sreenivas Bagalkote <Sreenivas.Bagalkote@lsil.com> + * Sumant Patro <Sumant.Patro@lsil.com> + * + * List of supported controllers + * + * OEM Product Name VID DID SSVID SSID + * --- ------------ --- --- ---- ---- + */ + +#include <linux/kernel.h> +#include <linux/types.h> +#include <linux/pci.h> +#include <linux/list.h> +#include <linux/version.h> +#include <linux/moduleparam.h> +#include <linux/module.h> +#include <linux/spinlock.h> +#include <linux/interrupt.h> +#include <linux/delay.h> +#include <linux/uio.h> +#include <asm/uaccess.h> +#include <linux/fs.h> +#include <linux/compat.h> + +#include <scsi/scsi.h> +#include <scsi/scsi_cmnd.h> +#include <scsi/scsi_device.h> +#include <scsi/scsi_host.h> +#include "megaraid_sas.h" + +MODULE_LICENSE("GPL"); +MODULE_VERSION(MEGASAS_VERSION); +MODULE_AUTHOR("sreenivas.bagalkote@lsil.com"); +MODULE_DESCRIPTION("LSI Logic MegaRAID SAS Driver"); + +/* + * PCI ID table for all supported controllers + */ +static struct pci_device_id megasas_pci_table[] = { + + { + PCI_VENDOR_ID_LSI_LOGIC, + PCI_DEVICE_ID_LSI_SAS1064R, + PCI_ANY_ID, + PCI_ANY_ID, + }, + { + PCI_VENDOR_ID_DELL, + PCI_DEVICE_ID_DELL_PERC5, + PCI_ANY_ID, + PCI_ANY_ID, + }, + {0} /* Terminating entry */ +}; + +MODULE_DEVICE_TABLE(pci, megasas_pci_table); + +static int megasas_mgmt_majorno; +static struct megasas_mgmt_info megasas_mgmt_info; +static struct fasync_struct *megasas_async_queue; +static DECLARE_MUTEX(megasas_async_queue_mutex); + +/** + * megasas_get_cmd - Get a command from the free pool + * @instance: Adapter soft state + * + * Returns a free command from the pool + */ +static inline struct megasas_cmd *megasas_get_cmd(struct megasas_instance + *instance) +{ + unsigned long flags; + struct megasas_cmd *cmd = NULL; + + spin_lock_irqsave(&instance->cmd_pool_lock, flags); + + if (!list_empty(&instance->cmd_pool)) { + cmd = list_entry((&instance->cmd_pool)->next, + struct megasas_cmd, list); + list_del_init(&cmd->list); + } else { + printk(KERN_ERR "megasas: Command pool empty!\n"); + } + + spin_unlock_irqrestore(&instance->cmd_pool_lock, flags); + return cmd; +} + +/** + * megasas_return_cmd - Return a cmd to free command pool + * @instance: Adapter soft state + * @cmd: Command packet to be returned to free command pool + */ +static inline void +megasas_return_cmd(struct megasas_instance *instance, struct megasas_cmd *cmd) +{ + unsigned long flags; + + spin_lock_irqsave(&instance->cmd_pool_lock, flags); + + cmd->scmd = NULL; + list_add_tail(&cmd->list, &instance->cmd_pool); + + spin_unlock_irqrestore(&instance->cmd_pool_lock, flags); +} + +/** + * megasas_enable_intr - Enables interrupts + * @regs: MFI register set + */ +static inline void +megasas_enable_intr(struct megasas_register_set __iomem * regs) +{ + writel(1, &(regs)->outbound_intr_mask); + + /* Dummy readl to force pci flush */ + readl(®s->outbound_intr_mask); +} + +/** + * megasas_disable_intr - Disables interrupts + * @regs: MFI register set + */ +static inline void +megasas_disable_intr(struct megasas_register_set __iomem * regs) +{ + u32 mask = readl(®s->outbound_intr_mask) & (~0x00000001); + writel(mask, ®s->outbound_intr_mask); + + /* Dummy readl to force pci flush */ + readl(®s->outbound_intr_mask); +} + +/** + * megasas_issue_polled - Issues a polling command + * @instance: Adapter soft state + * @cmd: Command packet to be issued + * + * For polling, MFI requires the cmd_status to be set to 0xFF before posting. + */ +static int +megasas_issue_polled(struct megasas_instance *instance, struct megasas_cmd *cmd) +{ + int i; + u32 msecs = MFI_POLL_TIMEOUT_SECS * 1000; + + struct megasas_header *frame_hdr = &cmd->frame->hdr; + + frame_hdr->cmd_status = 0xFF; + frame_hdr->flags |= MFI_FRAME_DONT_POST_IN_REPLY_QUEUE; + + /* + * Issue the frame using inbound queue port + */ + writel(cmd->frame_phys_addr >> 3, + &instance->reg_set->inbound_queue_port); + + /* + * Wait for cmd_status to change + */ + for (i = 0; (i < msecs) && (frame_hdr->cmd_status == 0xff); i++) { + rmb(); + msleep(1); + } + + if (frame_hdr->cmd_status == 0xff) + return -ETIME; + + return 0; +} + +/** + * megasas_issue_blocked_cmd - Synchronous wrapper around regular FW cmds + * @instance: Adapter soft state + * @cmd: Command to be issued + * + * This function waits on an event for the command to be returned from ISR. + * Used to issue ioctl commands. + */ +static int +megasas_issue_blocked_cmd(struct megasas_instance *instance, + struct megasas_cmd *cmd) +{ + cmd->cmd_status = ENODATA; + + writel(cmd->frame_phys_addr >> 3, + &instance->reg_set->inbound_queue_port); + + wait_event(instance->int_cmd_wait_q, (cmd->cmd_status != ENODATA)); + + return 0; +} + +/** + * megasas_issue_blocked_abort_cmd - Aborts previously issued cmd + * @instance: Adapter soft state + * @cmd_to_abort: Previously issued cmd to be aborted + * + * MFI firmware can abort previously issued AEN comamnd (automatic event + * notification). The megasas_issue_blocked_abort_cmd() issues such abort + * cmd and blocks till it is completed. + */ +static int +megasas_issue_blocked_abort_cmd(struct megasas_instance *instance, + struct megasas_cmd *cmd_to_abort) +{ + struct megasas_cmd *cmd; + struct megasas_abort_frame *abort_fr; + + cmd = megasas_get_cmd(instance); + + if (!cmd) + return -1; + + abort_fr = &cmd->frame->abort; + + /* + * Prepare and issue the abort frame + */ + abort_fr->cmd = MFI_CMD_ABORT; + abort_fr->cmd_status = 0xFF; + abort_fr->flags = 0; + abort_fr->abort_context = cmd_to_abort->index; + abort_fr->abort_mfi_phys_addr_lo = cmd_to_abort->frame_phys_addr; + abort_fr->abort_mfi_phys_addr_hi = 0; + + cmd->sync_cmd = 1; + cmd->cmd_status = 0xFF; + + writel(cmd->frame_phys_addr >> 3, + &instance->reg_set->inbound_queue_port); + + /* + * Wait for this cmd to complete + */ + wait_event(instance->abort_cmd_wait_q, (cmd->cmd_status != 0xFF)); + + megasas_return_cmd(instance, cmd); + return 0; +} + +/** + * megasas_make_sgl32 - Prepares 32-bit SGL + * @instance: Adapter soft state + * @scp: SCSI command from the mid-layer + * @mfi_sgl: SGL to be filled in + * + * If successful, this function returns the number of SG elements. Otherwise, + * it returnes -1. + */ +static inline int +megasas_make_sgl32(struct megasas_instance *instance, struct scsi_cmnd *scp, + union megasas_sgl *mfi_sgl) +{ + int i; + int sge_count; + struct scatterlist *os_sgl; + + /* + * Return 0 if there is no data transfer + */ + if (!scp->request_buffer || !scp->request_bufflen) + return 0; + + if (!scp->use_sg) { + mfi_sgl->sge32[0].phys_addr = pci_map_single(instance->pdev, + scp-> + request_buffer, + scp-> + request_bufflen, + scp-> + sc_data_direction); + mfi_sgl->sge32[0].length = scp->request_bufflen; + + return 1; + } + + os_sgl = (struct scatterlist *)scp->request_buffer; + sge_count = pci_map_sg(instance->pdev, os_sgl, scp->use_sg, + scp->sc_data_direction); + + for (i = 0; i < sge_count; i++, os_sgl++) { + mfi_sgl->sge32[i].length = sg_dma_len(os_sgl); + mfi_sgl->sge32[i].phys_addr = sg_dma_address(os_sgl); + } + + return sge_count; +} + +/** + * megasas_make_sgl64 - Prepares 64-bit SGL + * @instance: Adapter soft state + * @scp: SCSI command from the mid-layer + * @mfi_sgl: SGL to be filled in + * + * If successful, this function returns the number of SG elements. Otherwise, + * it returnes -1. + */ +static inline int +megasas_make_sgl64(struct megasas_instance *instance, struct scsi_cmnd *scp, + union megasas_sgl *mfi_sgl) +{ + int i; + int sge_count; + struct scatterlist *os_sgl; + + /* + * Return 0 if there is no data transfer + */ + if (!scp->request_buffer || !scp->request_bufflen) + return 0; + + if (!scp->use_sg) { + mfi_sgl->sge64[0].phys_addr = pci_map_single(instance->pdev, + scp-> + request_buffer, + scp-> + request_bufflen, + scp-> + sc_data_direction); + + mfi_sgl->sge64[0].length = scp->request_bufflen; + + return 1; + } + + os_sgl = (struct scatterlist *)scp->request_buffer; + sge_count = pci_map_sg(instance->pdev, os_sgl, scp->use_sg, + scp->sc_data_direction); + + for (i = 0; i < sge_count; i++, os_sgl++) { + mfi_sgl->sge64[i].length = sg_dma_len(os_sgl); + mfi_sgl->sge64[i].phys_addr = sg_dma_address(os_sgl); + } + + return sge_count; +} + +/** + * megasas_build_dcdb - Prepares a direct cdb (DCDB) command + * @instance: Adapter soft state + * @scp: SCSI command + * @cmd: Command to be prepared in + * + * This function prepares CDB commands. These are typcially pass-through + * commands to the devices. + */ +static inline int +megasas_build_dcdb(struct megasas_instance *instance, struct scsi_cmnd *scp, + struct megasas_cmd *cmd) +{ + u32 sge_sz; + int sge_bytes; + u32 is_logical; + u32 device_id; + u16 flags = 0; + struct megasas_pthru_frame *pthru; + + is_logical = MEGASAS_IS_LOGICAL(scp); + device_id = MEGASAS_DEV_INDEX(instance, scp); + pthru = (struct megasas_pthru_frame *)cmd->frame; + + if (scp->sc_data_direction == PCI_DMA_TODEVICE) + flags = MFI_FRAME_DIR_WRITE; + else if (scp->sc_data_direction == PCI_DMA_FROMDEVICE) + flags = MFI_FRAME_DIR_READ; + else if (scp->sc_data_direction == PCI_DMA_NONE) + flags = MFI_FRAME_DIR_NONE; + + /* + * Prepare the DCDB frame + */ + pthru->cmd = (is_logical) ? MFI_CMD_LD_SCSI_IO : MFI_CMD_PD_SCSI_IO; + pthru->cmd_status = 0x0; + pthru->scsi_status = 0x0; + pthru->target_id = device_id; + pthru->lun = scp->device->lun; + pthru->cdb_len = scp->cmd_len; + pthru->timeout = 0; + pthru->flags = flags; + pthru->data_xfer_len = scp->request_bufflen; + + memcpy(pthru->cdb, scp->cmnd, scp->cmd_len); + + /* + * Construct SGL + */ + sge_sz = (IS_DMA64) ? sizeof(struct megasas_sge64) : + sizeof(struct megasas_sge32); + + if (IS_DMA64) { + pthru->flags |= MFI_FRAME_SGL64; + pthru->sge_count = megasas_make_sgl64(instance, scp, + &pthru->sgl); + } else + pthru->sge_count = megasas_make_sgl32(instance, scp, + &pthru->sgl); + + /* + * Sense info specific + */ + pthru->sense_len = SCSI_SENSE_BUFFERSIZE; + pthru->sense_buf_phys_addr_hi = 0; + pthru->sense_buf_phys_addr_lo = cmd->sense_phys_addr; + + sge_bytes = sge_sz * pthru->sge_count; + + /* + * Compute the total number of frames this command consumes. FW uses + * this number to pull sufficient number of frames from host memory. + */ + cmd->frame_count = (sge_bytes / MEGAMFI_FRAME_SIZE) + + ((sge_bytes % MEGAMFI_FRAME_SIZE) ? 1 : 0) + 1; + + if (cmd->frame_count > 7) + cmd->frame_count = 8; + + return cmd->frame_count; +} + +/** + * megasas_build_ldio - Prepares IOs to logical devices + * @instance: Adapter soft state + * @scp: SCSI command + * @cmd: Command to to be prepared + * + * Frames (and accompanying SGLs) for regular SCSI IOs use this function. + */ +static inline int +megasas_build_ldio(struct megasas_instance *instance, struct scsi_cmnd *scp, + struct megasas_cmd *cmd) +{ + u32 sge_sz; + int sge_bytes; + u32 device_id; + u8 sc = scp->cmnd[0]; + u16 flags = 0; + struct megasas_io_frame *ldio; + + device_id = MEGASAS_DEV_INDEX(instance, scp); + ldio = (struct megasas_io_frame *)cmd->frame; + + if (scp->sc_data_direction == PCI_DMA_TODEVICE) + flags = MFI_FRAME_DIR_WRITE; + else if (scp->sc_data_direction == PCI_DMA_FROMDEVICE) + flags = MFI_FRAME_DIR_READ; + + /* + * Preare the Logical IO frame: 2nd bit is zero for all read cmds + */ + ldio->cmd = (sc & 0x02) ? MFI_CMD_LD_WRITE : MFI_CMD_LD_READ; + ldio->cmd_status = 0x0; + ldio->scsi_status = 0x0; + ldio->target_id = device_id; + ldio->timeout = 0; + ldio->reserved_0 = 0; + ldio->pad_0 = 0; + ldio->flags = flags; + ldio->start_lba_hi = 0; + ldio->access_byte = (scp->cmd_len != 6) ? scp->cmnd[1] : 0; + + /* + * 6-byte READ(0x08) or WRITE(0x0A) cdb + */ + if (scp->cmd_len == 6) { + ldio->lba_count = (u32) scp->cmnd[4]; + ldio->start_lba_lo = ((u32) scp->cmnd[1] << 16) | + ((u32) scp->cmnd[2] << 8) | (u32) scp->cmnd[3]; + + ldio->start_lba_lo &= 0x1FFFFF; + } + + /* + * 10-byte READ(0x28) or WRITE(0x2A) cdb + */ + else if (scp->cmd_len == 10) { + ldio->lba_count = (u32) scp->cmnd[8] | + ((u32) scp->cmnd[7] << 8); + ldio->start_lba_lo = ((u32) scp->cmnd[2] << 24) | + ((u32) scp->cmnd[3] << 16) | + ((u32) scp->cmnd[4] << 8) | (u32) scp->cmnd[5]; + } + + /* + * 12-byte READ(0xA8) or WRITE(0xAA) cdb + */ + else if (scp->cmd_len == 12) { + ldio->lba_count = ((u32) scp->cmnd[6] << 24) | + ((u32) scp->cmnd[7] << 16) | + ((u32) scp->cmnd[8] << 8) | (u32) scp->cmnd[9]; + + ldio->start_lba_lo = ((u32) scp->cmnd[2] << 24) | + ((u32) scp->cmnd[3] << 16) | + ((u32) scp->cmnd[4] << 8) | (u32) scp->cmnd[5]; + } + + /* + * 16-byte READ(0x88) or WRITE(0x8A) cdb + */ + else if (scp->cmd_len == 16) { + ldio->lba_count = ((u32) scp->cmnd[10] << 24) | + ((u32) scp->cmnd[11] << 16) | + ((u32) scp->cmnd[12] << 8) | (u32) scp->cmnd[13]; + + ldio->start_lba_lo = ((u32) scp->cmnd[6] << 24) | + ((u32) scp->cmnd[7] << 16) | + ((u32) scp->cmnd[8] << 8) | (u32) scp->cmnd[9]; + + ldio->start_lba_hi = ((u32) scp->cmnd[2] << 24) | + ((u32) scp->cmnd[3] << 16) | + ((u32) scp->cmnd[4] << 8) | (u32) scp->cmnd[5]; + + } + + /* + * Construct SGL + */ + sge_sz = (IS_DMA64) ? sizeof(struct megasas_sge64) : + sizeof(struct megasas_sge32); + + if (IS_DMA64) { + ldio->flags |= MFI_FRAME_SGL64; + ldio->sge_count = megasas_make_sgl64(instance, scp, &ldio->sgl); + } else + ldio->sge_count = megasas_make_sgl32(instance, scp, &ldio->sgl); + + /* + * Sense info specific + */ + ldio->sense_len = SCSI_SENSE_BUFFERSIZE; + ldio->sense_buf_phys_addr_hi = 0; + ldio->sense_buf_phys_addr_lo = cmd->sense_phys_addr; + + sge_bytes = sge_sz * ldio->sge_count; + + cmd->frame_count = (sge_bytes / MEGAMFI_FRAME_SIZE) + + ((sge_bytes % MEGAMFI_FRAME_SIZE) ? 1 : 0) + 1; + + if (cmd->frame_count > 7) + cmd->frame_count = 8; + + return cmd->frame_count; +} + +/** + * megasas_build_cmd - Prepares a command packet + * @instance: Adapter soft state + * @scp: SCSI command + * @frame_count: [OUT] Number of frames used to prepare this command + */ +static inline struct megasas_cmd *megasas_build_cmd(struct megasas_instance + *instance, + struct scsi_cmnd *scp, + int *frame_count) +{ + u32 logical_cmd; + struct megasas_cmd *cmd; + + /* + * Find out if this is logical or physical drive command. + */ + logical_cmd = MEGASAS_IS_LOGICAL(scp); + + /* + * Logical drive command + */ + if (logical_cmd) { + + if (scp->device->id >= MEGASAS_MAX_LD) { + scp->result = DID_BAD_TARGET << 16; + return NULL; + } + + switch (scp->cmnd[0]) { + + case READ_10: + case WRITE_10: + case READ_12: + case WRITE_12: + case READ_6: + case WRITE_6: + case READ_16: + case WRITE_16: + /* + * Fail for LUN > 0 + */ + if (scp->device->lun) { + scp->result = DID_BAD_TARGET << 16; + return NULL; + } + + cmd = megasas_get_cmd(instance); + + if (!cmd) { + scp->result = DID_IMM_RETRY << 16; + return NULL; + } + + *frame_count = megasas_build_ldio(instance, scp, cmd); + + if (!(*frame_count)) { + megasas_return_cmd(instance, cmd); + return NULL; + } + + return cmd; + + default: + /* + * Fail for LUN > 0 + */ + if (scp->device->lun) { + scp->result = DID_BAD_TARGET << 16; + return NULL; + } + + cmd = megasas_get_cmd(instance); + + if (!cmd) { + scp->result = DID_IMM_RETRY << 16; + return NULL; + } + + *frame_count = megasas_build_dcdb(instance, scp, cmd); + + if (!(*frame_count)) { + megasas_return_cmd(instance, cmd); + return NULL; + } + + return cmd; + } + } else { + cmd = megasas_get_cmd(instance); + + if (!cmd) { + scp->result = DID_IMM_RETRY << 16; + return NULL; + } + + *frame_count = megasas_build_dcdb(instance, scp, cmd); + + if (!(*frame_count)) { + megasas_return_cmd(instance, cmd); + return NULL; + } + + return cmd; + } + + return NULL; +} + +/** + * megasas_queue_command - Queue entry point + * @scmd: SCSI command to be queued + * @done: Callback entry point + */ +static int +megasas_queue_command(struct scsi_cmnd *scmd, void (*done) (struct scsi_cmnd *)) +{ + u32 frame_count; + unsigned long flags; + struct megasas_cmd *cmd; + struct megasas_instance *instance; + + instance = (struct megasas_instance *) + scmd->device->host->hostdata; + scmd->scsi_done = done; + scmd->result = 0; + + cmd = megasas_build_cmd(instance, scmd, &frame_count); + + if (!cmd) { + done(scmd); + return 0; + } + + cmd->scmd = scmd; + scmd->SCp.ptr = (char *)cmd; + scmd->SCp.sent_command = jiffies; + + /* + * Issue the command to the FW + */ + spin_lock_irqsave(&instance->instance_lock, flags); + instance->fw_outstanding++; + spin_unlock_irqrestore(&instance->instance_lock, flags); + + writel(((cmd->frame_phys_addr >> 3) | (cmd->frame_count - 1)), + &instance->reg_set->inbound_queue_port); + + return 0; +} + +/** + * megasas_wait_for_outstanding - Wait for all outstanding cmds + * @instance: Adapter soft state + * + * This function waits for upto MEGASAS_RESET_WAIT_TIME seconds for FW to + * complete all its outstanding commands. Returns error if one or more IOs + * are pending after this time period. It also marks the controller dead. + */ +static int megasas_wait_for_outstanding(struct megasas_instance *instance) +{ + int i; + u32 wait_time = MEGASAS_RESET_WAIT_TIME; + + for (i = 0; i < wait_time; i++) { + + if (!instance->fw_outstanding) + break; + + if (!(i % MEGASAS_RESET_NOTICE_INTERVAL)) { + printk(KERN_NOTICE "megasas: [%2d]waiting for %d " + "commands to complete\n", i, + instance->fw_outstanding); + } + + msleep(1000); + } + + if (instance->fw_outstanding) { + instance->hw_crit_error = 1; + return FAILED; + } + + return SUCCESS; +} + +/** + * megasas_generic_reset - Generic reset routine + * @scmd: Mid-layer SCSI command + * + * This routine implements a generic reset handler for device, bus and host + * reset requests. Device, bus and host specific reset handlers can use this + * function after they do their specific tasks. + */ +static int megasas_generic_reset(struct scsi_cmnd *scmd) +{ + int ret_val; + struct megasas_instance *instance; + + instance = (struct megasas_instance *)scmd->device->host->hostdata; + + printk(KERN_NOTICE "megasas: RESET -%ld cmd=%x <c=%d t=%d l=%d>\n", + scmd->serial_number, scmd->cmnd[0], scmd->device->channel, + scmd->device->id, scmd->device->lun); + + if (instance->hw_crit_error) { + printk(KERN_ERR "megasas: cannot recover from previous reset " + "failures\n"); + return FAILED; + } + + spin_unlock(scmd->device->host->host_lock); + + ret_val = megasas_wait_for_outstanding(instance); + + if (ret_val == SUCCESS) + printk(KERN_NOTICE "megasas: reset successful \n"); + else + printk(KERN_ERR "megasas: failed to do reset\n"); + + spin_lock(scmd->device->host->host_lock); + + return ret_val; +} + +static enum scsi_eh_timer_return megasas_reset_timer(struct scsi_cmnd *scmd) +{ + unsigned long seconds; + + if (scmd->SCp.ptr) { + seconds = (jiffies - scmd->SCp.sent_command) / HZ; + + if (seconds < 90) { + return EH_RESET_TIMER; + } else { + return EH_NOT_HANDLED; + } + } + + return EH_HANDLED; +} + +/** + * megasas_reset_device - Device reset handler entry point + */ +static int megasas_reset_device(struct scsi_cmnd *scmd) +{ + int ret; + + /* + * First wait for all commands to complete + */ + ret = megasas_generic_reset(scmd); + + return ret; +} + +/** + * megasas_reset_bus_host - Bus & host reset handler entry point + */ +static int megasas_reset_bus_host(struct scsi_cmnd *scmd) +{ + int ret; + + /* + * Frist wait for all commands to complete + */ + ret = megasas_generic_reset(scmd); + + return ret; +} + +/** + * megasas_service_aen - Processes an event notification + * @instance: Adapter soft state + * @cmd: AEN command completed by the ISR + * + * For AEN, driver sends a command down to FW that is held by the FW till an + * event occurs. When an event of interest occurs, FW completes the command + * that it was previously holding. + * + * This routines sends SIGIO signal to processes that have registered with the + * driver for AEN. + */ +static void +megasas_service_aen(struct megasas_instance *instance, struct megasas_cmd *cmd) +{ + /* + * Don't signal app if it is just an aborted previously registered aen + */ + if (!cmd->abort_aen) + kill_fasync(&megasas_async_queue, SIGIO, POLL_IN); + else + cmd->abort_aen = 0; + + instance->aen_cmd = NULL; + megasas_return_cmd(instance, cmd); +} + +/* + * Scsi host template for megaraid_sas driver + */ +static struct scsi_host_template megasas_template = { + + .module = THIS_MODULE, + .name = "LSI Logic SAS based MegaRAID driver", + .proc_name = "megaraid_sas", + .queuecommand = megasas_queue_command, + .eh_device_reset_handler = megasas_reset_device, + .eh_bus_reset_handler = megasas_reset_bus_host, + .eh_host_reset_handler = megasas_reset_bus_host, + .eh_timed_out = megasas_reset_timer, + .use_clustering = ENABLE_CLUSTERING, +}; + +/** + * megasas_complete_int_cmd - Completes an internal command + * @instance: Adapter soft state + * @cmd: Command to be completed + * + * The megasas_issue_blocked_cmd() function waits for a command to complete + * after it issues a command. This function wakes up that waiting routine by + * calling wake_up() on the wait queue. + */ +static void +megasas_complete_int_cmd(struct megasas_instance *instance, + struct megasas_cmd *cmd) +{ + cmd->cmd_status = cmd->frame->io.cmd_status; + + if (cmd->cmd_status == ENODATA) { + cmd->cmd_status = 0; + } + wake_up(&instance->int_cmd_wait_q); +} + +/** + * megasas_complete_abort - Completes aborting a command + * @instance: Adapter soft state + * @cmd: Cmd that was issued to abort another cmd + * + * The megasas_issue_blocked_abort_cmd() function waits on abort_cmd_wait_q + * after it issues an abort on a previously issued command. This function + * wakes up all functions waiting on the same wait queue. + */ +static void +megasas_complete_abort(struct megasas_instance *instance, + struct megasas_cmd *cmd) +{ + if (cmd->sync_cmd) { + cmd->sync_cmd = 0; + cmd->cmd_status = 0; + wake_up(&instance->abort_cmd_wait_q); + } + + return; +} + +/** + * megasas_unmap_sgbuf - Unmap SG buffers + * @instance: Adapter soft state + * @cmd: Completed command + */ +static inline void +megasas_unmap_sgbuf(struct megasas_instance *instance, struct megasas_cmd *cmd) +{ + dma_addr_t buf_h; + u8 opcode; + + if (cmd->scmd->use_sg) { + pci_unmap_sg(instance->pdev, cmd->scmd->request_buffer, + cmd->scmd->use_sg, cmd->scmd->sc_data_direction); + return; + } + + if (!cmd->scmd->request_bufflen) + return; + + opcode = cmd->frame->hdr.cmd; + + if ((opcode == MFI_CMD_LD_READ) || (opcode == MFI_CMD_LD_WRITE)) { + if (IS_DMA64) + buf_h = cmd->frame->io.sgl.sge64[0].phys_addr; + else + buf_h = cmd->frame->io.sgl.sge32[0].phys_addr; + } else { + if (IS_DMA64) + buf_h = cmd->frame->pthru.sgl.sge64[0].phys_addr; + else + buf_h = cmd->frame->pthru.sgl.sge32[0].phys_addr; + } + + pci_unmap_single(instance->pdev, buf_h, cmd->scmd->request_bufflen, + cmd->scmd->sc_data_direction); + return; +} + +/** + * megasas_complete_cmd - Completes a command + * @instance: Adapter soft state + * @cmd: Command to be completed + * @alt_status: If non-zero, use this value as status to + * SCSI mid-layer instead of the value returned + * by the FW. This should be used if caller wants + * an alternate status (as in the case of aborted + * commands) + */ +static inline void +megasas_complete_cmd(struct megasas_instance *instance, struct megasas_cmd *cmd, + u8 alt_status) +{ + int exception = 0; + struct megasas_header *hdr = &cmd->frame->hdr; + unsigned long flags; + + if (cmd->scmd) { + cmd->scmd->SCp.ptr = (char *)0; + } + + switch (hdr->cmd) { + + case MFI_CMD_PD_SCSI_IO: + case MFI_CMD_LD_SCSI_IO: + + /* + * MFI_CMD_PD_SCSI_IO and MFI_CMD_LD_SCSI_IO could have been + * issued either through an IO path or an IOCTL path. If it + * was via IOCTL, we will send it to internal completion. + */ + if (cmd->sync_cmd) { + cmd->sync_cmd = 0; + megasas_complete_int_cmd(instance, cmd); + break; + } + + /* + * Don't export physical disk devices to mid-layer. + */ + if (!MEGASAS_IS_LOGICAL(cmd->scmd) && + (hdr->cmd_status == MFI_STAT_OK) && + (cmd->scmd->cmnd[0] == INQUIRY)) { + + if (((*(u8 *) cmd->scmd->request_buffer) & 0x1F) == + TYPE_DISK) { + cmd->scmd->result = DID_BAD_TARGET << 16; + exception = 1; + } + } + + case MFI_CMD_LD_READ: + case MFI_CMD_LD_WRITE: + + if (alt_status) { + cmd->scmd->result = alt_status << 16; + exception = 1; + } + + if (exception) { + + spin_lock_irqsave(&instance->instance_lock, flags); + instance->fw_outstanding--; + spin_unlock_irqrestore(&instance->instance_lock, flags); + + megasas_unmap_sgbuf(instance, cmd); + cmd->scmd->scsi_done(cmd->scmd); + megasas_return_cmd(instance, cmd); + + break; + } + + switch (hdr->cmd_status) { + + case MFI_STAT_OK: + cmd->scmd->result = DID_OK << 16; + break; + + case MFI_STAT_SCSI_IO_FAILED: + case MFI_STAT_LD_INIT_IN_PROGRESS: + cmd->scmd->result = + (DID_ERROR << 16) | hdr->scsi_status; + break; + + case MFI_STAT_SCSI_DONE_WITH_ERROR: + + cmd->scmd->result = (DID_OK << 16) | hdr->scsi_status; + + if (hdr->scsi_status == SAM_STAT_CHECK_CONDITION) { + memset(cmd->scmd->sense_buffer, 0, + SCSI_SENSE_BUFFERSIZE); + memcpy(cmd->scmd->sense_buffer, cmd->sense, + hdr->sense_len); + + cmd->scmd->result |= DRIVER_SENSE << 24; + } + + break; + + case MFI_STAT_LD_OFFLINE: + case MFI_STAT_DEVICE_NOT_FOUND: + cmd->scmd->result = DID_BAD_TARGET << 16; + break; + + default: + printk(KERN_DEBUG "megasas: MFI FW status %#x\n", + hdr->cmd_status); + cmd->scmd->result = DID_ERROR << 16; + break; + } + + spin_lock_irqsave(&instance->instance_lock, flags); + instance->fw_outstanding--; + spin_unlock_irqrestore(&instance->instance_lock, flags); + + megasas_unmap_sgbuf(instance, cmd); + cmd->scmd->scsi_done(cmd->scmd); + megasas_return_cmd(instance, cmd); + + break; + + case MFI_CMD_SMP: + case MFI_CMD_STP: + case MFI_CMD_DCMD: + + /* + * See if got an event notification + */ + if (cmd->frame->dcmd.opcode == MR_DCMD_CTRL_EVENT_WAIT) + megasas_service_aen(instance, cmd); + else + megasas_complete_int_cmd(instance, cmd); + + break; + + case MFI_CMD_ABORT: + /* + * Cmd issued to abort another cmd returned + */ + megasas_complete_abort(instance, cmd); + break; + + default: + printk("megasas: Unknown command completed! [0x%X]\n", + hdr->cmd); + break; + } +} + +/** + * megasas_deplete_reply_queue - Processes all completed commands + * @instance: Adapter soft state + * @alt_status: Alternate status to be returned to + * SCSI mid-layer instead of the status + * returned by the FW + */ +static inline int +megasas_deplete_reply_queue(struct megasas_instance *instance, u8 alt_status) +{ + u32 status; + u32 producer; + u32 consumer; + u32 context; + struct megasas_cmd *cmd; + + /* + * Check if it is our interrupt + */ + status = readl(&instance->reg_set->outbound_intr_status); + + if (!(status & MFI_OB_INTR_STATUS_MASK)) { + return IRQ_NONE; + } + + /* + * Clear the interrupt by writing back the same value + */ + writel(status, &instance->reg_set->outbound_intr_status); + + producer = *instance->producer; + consumer = *instance->consumer; + + while (consumer != producer) { + context = instance->reply_queue[consumer]; + + cmd = instance->cmd_list[context]; + + megasas_complete_cmd(instance, cmd, alt_status); + + consumer++; + if (consumer == (instance->max_fw_cmds + 1)) { + consumer = 0; + } + } + + *instance->consumer = producer; + + return IRQ_HANDLED; +} + +/** + * megasas_isr - isr entry point + */ +static irqreturn_t megasas_isr(int irq, void *devp, struct pt_regs *regs) +{ + return megasas_deplete_reply_queue((struct megasas_instance *)devp, + DID_OK); +} + +/** + * megasas_transition_to_ready - Move the FW to READY state + * @reg_set: MFI register set + * + * During the initialization, FW passes can potentially be in any one of + * several possible states. If the FW in operational, waiting-for-handshake + * states, driver must take steps to bring it to ready state. Otherwise, it + * has to wait for the ready state. + */ +static int +megasas_transition_to_ready(struct megasas_register_set __iomem * reg_set) +{ + int i; + u8 max_wait; + u32 fw_state; + u32 cur_state; + + fw_state = readl(®_set->outbound_msg_0) & MFI_STATE_MASK; + + while (fw_state != MFI_STATE_READY) { + + printk(KERN_INFO "megasas: Waiting for FW to come to ready" + " state\n"); + switch (fw_state) { + + case MFI_STATE_FAULT: + + printk(KERN_DEBUG "megasas: FW in FAULT state!!\n"); + return -ENODEV; + + case MFI_STATE_WAIT_HANDSHAKE: + /* + * Set the CLR bit in inbound doorbell + */ + writel(MFI_INIT_CLEAR_HANDSHAKE, + ®_set->inbound_doorbell); + + max_wait = 2; + cur_state = MFI_STATE_WAIT_HANDSHAKE; + break; + + case MFI_STATE_OPERATIONAL: + /* + * Bring it to READY state; assuming max wait 2 secs + */ + megasas_disable_intr(reg_set); + writel(MFI_INIT_READY, ®_set->inbound_doorbell); + + max_wait = 10; + cur_state = MFI_STATE_OPERATIONAL; + break; + + case MFI_STATE_UNDEFINED: + /* + * This state should not last for more than 2 seconds + */ + max_wait = 2; + cur_state = MFI_STATE_UNDEFINED; + break; + + case MFI_STATE_BB_INIT: + max_wait = 2; + cur_state = MFI_STATE_BB_INIT; + break; + + case MFI_STATE_FW_INIT: + max_wait = 20; + cur_state = MFI_STATE_FW_INIT; + break; + + case MFI_STATE_FW_INIT_2: + max_wait = 20; + cur_state = MFI_STATE_FW_INIT_2; + break; + + case MFI_STATE_DEVICE_SCAN: + max_wait = 20; + cur_state = MFI_STATE_DEVICE_SCAN; + break; + + case MFI_STATE_FLUSH_CACHE: + max_wait = 20; + cur_state = MFI_STATE_FLUSH_CACHE; + break; + + default: + printk(KERN_DEBUG "megasas: Unknown state 0x%x\n", + fw_state); + return -ENODEV; + } + + /* + * The cur_state should not last for more than max_wait secs + */ + for (i = 0; i < (max_wait * 1000); i++) { + fw_state = MFI_STATE_MASK & + readl(®_set->outbound_msg_0); + + if (fw_state == cur_state) { + msleep(1); + } else + break; + } + + /* + * Return error if fw_state hasn't changed after max_wait + */ + if (fw_state == cur_state) { + printk(KERN_DEBUG "FW state [%d] hasn't changed " + "in %d secs\n", fw_state, max_wait); + return -ENODEV; + } + }; + + return 0; +} + +/** + * megasas_teardown_frame_pool - Destroy the cmd frame DMA pool + * @instance: Adapter soft state + */ +static void megasas_teardown_frame_pool(struct megasas_instance *instance) +{ + int i; + u32 max_cmd = instance->max_fw_cmds; + struct megasas_cmd *cmd; + + if (!instance->frame_dma_pool) + return; + + /* + * Return all frames to pool + */ + for (i = 0; i < max_cmd; i++) { + + cmd = instance->cmd_list[i]; + + if (cmd->frame) + pci_pool_free(instance->frame_dma_pool, cmd->frame, + cmd->frame_phys_addr); + + if (cmd->sense) + pci_pool_free(instance->sense_dma_pool, cmd->frame, + cmd->sense_phys_addr); + } + + /* + * Now destroy the pool itself + */ + pci_pool_destroy(instance->frame_dma_pool); + pci_pool_destroy(instance->sense_dma_pool); + + instance->frame_dma_pool = NULL; + instance->sense_dma_pool = NULL; +} + +/** + * megasas_create_frame_pool - Creates DMA pool for cmd frames + * @instance: Adapter soft state + * + * Each command packet has an embedded DMA memory buffer that is used for + * filling MFI frame and the SG list that immediately follows the frame. This + * function creates those DMA memory buffers for each command packet by using + * PCI pool facility. + */ +static int megasas_create_frame_pool(struct megasas_instance *instance) +{ + int i; + u32 max_cmd; + u32 sge_sz; + u32 sgl_sz; + u32 total_sz; + u32 frame_count; + struct megasas_cmd *cmd; + + max_cmd = instance->max_fw_cmds; + + /* + * Size of our frame is 64 bytes for MFI frame, followed by max SG + * elements and finally SCSI_SENSE_BUFFERSIZE bytes for sense buffer + */ + sge_sz = (IS_DMA64) ? sizeof(struct megasas_sge64) : + sizeof(struct megasas_sge32); + + /* + * Calculated the number of 64byte frames required for SGL + */ + sgl_sz = sge_sz * instance->max_num_sge; + frame_count = (sgl_sz + MEGAMFI_FRAME_SIZE - 1) / MEGAMFI_FRAME_SIZE; + + /* + * We need one extra frame for the MFI command + */ + frame_count++; + + total_sz = MEGAMFI_FRAME_SIZE * frame_count; + /* + * Use DMA pool facility provided by PCI layer + */ + instance->frame_dma_pool = pci_pool_create("megasas frame pool", + instance->pdev, total_sz, 64, + 0); + + if (!instance->frame_dma_pool) { + printk(KERN_DEBUG "megasas: failed to setup frame pool\n"); + return -ENOMEM; + } + + instance->sense_dma_pool = pci_pool_create("megasas sense pool", + instance->pdev, 128, 4, 0); + + if (!instance->sense_dma_pool) { + printk(KERN_DEBUG "megasas: failed to setup sense pool\n"); + + pci_pool_destroy(instance->frame_dma_pool); + instance->frame_dma_pool = NULL; + + return -ENOMEM; + } + + /* + * Allocate and attach a frame to each of the commands in cmd_list. + * By making cmd->index as the context instead of the &cmd, we can + * always use 32bit context regardless of the architecture + */ + for (i = 0; i < max_cmd; i++) { + + cmd = instance->cmd_list[i]; + + cmd->frame = pci_pool_alloc(instance->frame_dma_pool, + GFP_KERNEL, &cmd->frame_phys_addr); + + cmd->sense = pci_pool_alloc(instance->sense_dma_pool, + GFP_KERNEL, &cmd->sense_phys_addr); + + /* + * megasas_teardown_frame_pool() takes care of freeing + * whatever has been allocated + */ + if (!cmd->frame || !cmd->sense) { + printk(KERN_DEBUG "megasas: pci_pool_alloc failed \n"); + megasas_teardown_frame_pool(instance); + return -ENOMEM; + } + + cmd->frame->io.context = cmd->index; + } + + return 0; +} + +/** + * megasas_free_cmds - Free all the cmds in the free cmd pool + * @instance: Adapter soft state + */ +static void megasas_free_cmds(struct megasas_instance *instance) +{ + int i; + /* First free the MFI frame pool */ + megasas_teardown_frame_pool(instance); + + /* Free all the commands in the cmd_list */ + for (i = 0; i < instance->max_fw_cmds; i++) + kfree(instance->cmd_list[i]); + + /* Free the cmd_list buffer itself */ + kfree(instance->cmd_list); + instance->cmd_list = NULL; + + INIT_LIST_HEAD(&instance->cmd_pool); +} + +/** + * megasas_alloc_cmds - Allocates the command packets + * @instance: Adapter soft state + * + * Each command that is issued to the FW, whether IO commands from the OS or + * internal commands like IOCTLs, are wrapped in local data structure called + * megasas_cmd. The frame embedded in this megasas_cmd is actually issued to + * the FW. + * + * Each frame has a 32-bit field called context (tag). This context is used + * to get back the megasas_cmd from the frame when a frame gets completed in + * the ISR. Typically the address of the megasas_cmd itself would be used as + * the context. But we wanted to keep the differences between 32 and 64 bit + * systems to the mininum. We always use 32 bit integers for the context. In + * this driver, the 32 bit values are the indices into an array cmd_list. + * This array is used only to look up the megasas_cmd given the context. The + * free commands themselves are maintained in a linked list called cmd_pool. + */ +static int megasas_alloc_cmds(struct megasas_instance *instance) +{ + int i; + int j; + u32 max_cmd; + struct megasas_cmd *cmd; + + max_cmd = instance->max_fw_cmds; + + /* + * instance->cmd_list is an array of struct megasas_cmd pointers. + * Allocate the dynamic array first and then allocate individual + * commands. + */ + instance->cmd_list = kmalloc(sizeof(struct megasas_cmd *) * max_cmd, + GFP_KERNEL); + + if (!instance->cmd_list) { + printk(KERN_DEBUG "megasas: out of memory\n"); + return -ENOMEM; + } + + memset(instance->cmd_list, 0, sizeof(struct megasas_cmd *) * max_cmd); + + for (i = 0; i < max_cmd; i++) { + instance->cmd_list[i] = kmalloc(sizeof(struct megasas_cmd), + GFP_KERNEL); + + if (!instance->cmd_list[i]) { + + for (j = 0; j < i; j++) + kfree(instance->cmd_list[j]); + + kfree(instance->cmd_list); + instance->cmd_list = NULL; + + return -ENOMEM; + } + } + + /* + * Add all the commands to command pool (instance->cmd_pool) + */ + for (i = 0; i < max_cmd; i++) { + cmd = instance->cmd_list[i]; + memset(cmd, 0, sizeof(struct megasas_cmd)); + cmd->index = i; + cmd->instance = instance; + + list_add_tail(&cmd->list, &instance->cmd_pool); + } + + /* + * Create a frame pool and assign one frame to each cmd + */ + if (megasas_create_frame_pool(instance)) { + printk(KERN_DEBUG "megasas: Error creating frame DMA pool\n"); + megasas_free_cmds(instance); + } + + return 0; +} + +/** + * megasas_get_controller_info - Returns FW's controller structure + * @instance: Adapter soft state + * @ctrl_info: Controller information structure + * + * Issues an internal command (DCMD) to get the FW's controller structure. + * This information is mainly used to find out the maximum IO transfer per + * command supported by the FW. + */ +static int +megasas_get_ctrl_info(struct megasas_instance *instance, + struct megasas_ctrl_info *ctrl_info) +{ + int ret = 0; + struct megasas_cmd *cmd; + struct megasas_dcmd_frame *dcmd; + struct megasas_ctrl_info *ci; + dma_addr_t ci_h = 0; + + cmd = megasas_get_cmd(instance); + + if (!cmd) { + printk(KERN_DEBUG "megasas: Failed to get a free cmd\n"); + return -ENOMEM; + } + + dcmd = &cmd->frame->dcmd; + + ci = pci_alloc_consistent(instance->pdev, + sizeof(struct megasas_ctrl_info), &ci_h); + + if (!ci) { + printk(KERN_DEBUG "Failed to alloc mem for ctrl info\n"); + megasas_return_cmd(instance, cmd); + return -ENOMEM; + } + + memset(ci, 0, sizeof(*ci)); + memset(dcmd->mbox.b, 0, MFI_MBOX_SIZE); + + dcmd->cmd = MFI_CMD_DCMD; + dcmd->cmd_status = 0xFF; + dcmd->sge_count = 1; + dcmd->flags = MFI_FRAME_DIR_READ; + dcmd->timeout = 0; + dcmd->data_xfer_len = sizeof(struct megasas_ctrl_info); + dcmd->opcode = MR_DCMD_CTRL_GET_INFO; + dcmd->sgl.sge32[0].phys_addr = ci_h; + dcmd->sgl.sge32[0].length = sizeof(struct megasas_ctrl_info); + + if (!megasas_issue_polled(instance, cmd)) { + ret = 0; + memcpy(ctrl_info, ci, sizeof(struct megasas_ctrl_info)); + } else { + ret = -1; + } + + pci_free_consistent(instance->pdev, sizeof(struct megasas_ctrl_info), + ci, ci_h); + + megasas_return_cmd(instance, cmd); + return ret; +} + +/** + * megasas_init_mfi - Initializes the FW + * @instance: Adapter soft state + * + * This is the main function for initializing MFI firmware. + */ +static int megasas_init_mfi(struct megasas_instance *instance) +{ + u32 context_sz; + u32 reply_q_sz; + u32 max_sectors_1; + u32 max_sectors_2; + struct megasas_register_set __iomem *reg_set; + + struct megasas_cmd *cmd; + struct megasas_ctrl_info *ctrl_info; + + struct megasas_init_frame *init_frame; + struct megasas_init_queue_info *initq_info; + dma_addr_t init_frame_h; + dma_addr_t initq_info_h; + + /* + * Map the message registers + */ + instance->base_addr = pci_resource_start(instance->pdev, 0); + + if (pci_request_regions(instance->pdev, "megasas: LSI Logic")) { + printk(KERN_DEBUG "megasas: IO memory region busy!\n"); + return -EBUSY; + } + + instance->reg_set = ioremap_nocache(instance->base_addr, 8192); + + if (!instance->reg_set) { + printk(KERN_DEBUG "megasas: Failed to map IO mem\n"); + goto fail_ioremap; + } + + reg_set = instance->reg_set; + + /* + * We expect the FW state to be READY + */ + if (megasas_transition_to_ready(instance->reg_set)) + goto fail_ready_state; + + /* + * Get various operational parameters from status register + */ + instance->max_fw_cmds = readl(®_set->outbound_msg_0) & 0x00FFFF; + instance->max_num_sge = (readl(®_set->outbound_msg_0) & 0xFF0000) >> + 0x10; + /* + * Create a pool of commands + */ + if (megasas_alloc_cmds(instance)) + goto fail_alloc_cmds; + + /* + * Allocate memory for reply queue. Length of reply queue should + * be _one_ more than the maximum commands handled by the firmware. + * + * Note: When FW completes commands, it places corresponding contex + * values in this circular reply queue. This circular queue is a fairly + * typical producer-consumer queue. FW is the producer (of completed + * commands) and the driver is the consumer. + */ + context_sz = sizeof(u32); + reply_q_sz = context_sz * (instance->max_fw_cmds + 1); + + instance->reply_queue = pci_alloc_consistent(instance->pdev, + reply_q_sz, + &instance->reply_queue_h); + + if (!instance->reply_queue) { + printk(KERN_DEBUG "megasas: Out of DMA mem for reply queue\n"); + goto fail_reply_queue; + } + + /* + * Prepare a init frame. Note the init frame points to queue info + * structure. Each frame has SGL allocated after first 64 bytes. For + * this frame - since we don't need any SGL - we use SGL's space as + * queue info structure + * + * We will not get a NULL command below. We just created the pool. + */ + cmd = megasas_get_cmd(instance); + + init_frame = (struct megasas_init_frame *)cmd->frame; + initq_info = (struct megasas_init_queue_info *) + ((unsigned long)init_frame + 64); + + init_frame_h = cmd->frame_phys_addr; + initq_info_h = init_frame_h + 64; + + memset(init_frame, 0, MEGAMFI_FRAME_SIZE); + memset(initq_info, 0, sizeof(struct megasas_init_queue_info)); + + initq_info->reply_queue_entries = instance->max_fw_cmds + 1; + initq_info->reply_queue_start_phys_addr_lo = instance->reply_queue_h; + + initq_info->producer_index_phys_addr_lo = instance->producer_h; + initq_info->consumer_index_phys_addr_lo = instance->consumer_h; + + init_frame->cmd = MFI_CMD_INIT; + init_frame->cmd_status = 0xFF; + init_frame->queue_info_new_phys_addr_lo = initq_info_h; + + init_frame->data_xfer_len = sizeof(struct megasas_init_queue_info); + + /* + * Issue the init frame in polled mode + */ + if (megasas_issue_polled(instance, cmd)) { + printk(KERN_DEBUG "megasas: Failed to init firmware\n"); + goto fail_fw_init; + } + + megasas_return_cmd(instance, cmd); + + ctrl_info = kmalloc(sizeof(struct megasas_ctrl_info), GFP_KERNEL); + + /* + * Compute the max allowed sectors per IO: The controller info has two + * limits on max sectors. Driver should use the minimum of these two. + * + * 1 << stripe_sz_ops.min = max sectors per strip + * + * Note that older firmwares ( < FW ver 30) didn't report information + * to calculate max_sectors_1. So the number ended up as zero always. + */ + if (ctrl_info && !megasas_get_ctrl_info(instance, ctrl_info)) { + + max_sectors_1 = (1 << ctrl_info->stripe_sz_ops.min) * + ctrl_info->max_strips_per_io; + max_sectors_2 = ctrl_info->max_request_size; + + instance->max_sectors_per_req = (max_sectors_1 < max_sectors_2) + ? max_sectors_1 : max_sectors_2; + } else + instance->max_sectors_per_req = instance->max_num_sge * + PAGE_SIZE / 512; + + kfree(ctrl_info); + + return 0; + + fail_fw_init: + megasas_return_cmd(instance, cmd); + + pci_free_consistent(instance->pdev, reply_q_sz, + instance->reply_queue, instance->reply_queue_h); + fail_reply_queue: + megasas_free_cmds(instance); + + fail_alloc_cmds: + fail_ready_state: + iounmap(instance->reg_set); + + fail_ioremap: + pci_release_regions(instance->pdev); + + return -EINVAL; +} + +/** + * megasas_release_mfi - Reverses the FW initialization + * @intance: Adapter soft state + */ +static void megasas_release_mfi(struct megasas_instance *instance) +{ + u32 reply_q_sz = sizeof(u32) * (instance->max_fw_cmds + 1); + + pci_free_consistent(instance->pdev, reply_q_sz, + instance->reply_queue, instance->reply_queue_h); + + megasas_free_cmds(instance); + + iounmap(instance->reg_set); + + pci_release_regions(instance->pdev); +} + +/** + * megasas_get_seq_num - Gets latest event sequence numbers + * @instance: Adapter soft state + * @eli: FW event log sequence numbers information + * + * FW maintains a log of all events in a non-volatile area. Upper layers would + * usually find out the latest sequence number of the events, the seq number at + * the boot etc. They would "read" all the events below the latest seq number + * by issuing a direct fw cmd (DCMD). For the future events (beyond latest seq + * number), they would subsribe to AEN (asynchronous event notification) and + * wait for the events to happen. + */ +static int +megasas_get_seq_num(struct megasas_instance *instance, + struct megasas_evt_log_info *eli) +{ + struct megasas_cmd *cmd; + struct megasas_dcmd_frame *dcmd; + struct megasas_evt_log_info *el_info; + dma_addr_t el_info_h = 0; + + cmd = megasas_get_cmd(instance); + + if (!cmd) { + return -ENOMEM; + } + + dcmd = &cmd->frame->dcmd; + el_info = pci_alloc_consistent(instance->pdev, + sizeof(struct megasas_evt_log_info), + &el_info_h); + + if (!el_info) { + megasas_return_cmd(instance, cmd); + return -ENOMEM; + } + + memset(el_info, 0, sizeof(*el_info)); + memset(dcmd->mbox.b, 0, MFI_MBOX_SIZE); + + dcmd->cmd = MFI_CMD_DCMD; + dcmd->cmd_status = 0x0; + dcmd->sge_count = 1; + dcmd->flags = MFI_FRAME_DIR_READ; + dcmd->timeout = 0; + dcmd->data_xfer_len = sizeof(struct megasas_evt_log_info); + dcmd->opcode = MR_DCMD_CTRL_EVENT_GET_INFO; + dcmd->sgl.sge32[0].phys_addr = el_info_h; + dcmd->sgl.sge32[0].length = sizeof(struct megasas_evt_log_info); + + megasas_issue_blocked_cmd(instance, cmd); + + /* + * Copy the data back into callers buffer + */ + memcpy(eli, el_info, sizeof(struct megasas_evt_log_info)); + + pci_free_consistent(instance->pdev, sizeof(struct megasas_evt_log_info), + el_info, el_info_h); + + megasas_return_cmd(instance, cmd); + + return 0; +} + +/** + * megasas_register_aen - Registers for asynchronous event notification + * @instance: Adapter soft state + * @seq_num: The starting sequence number + * @class_locale: Class of the event + * + * This function subscribes for AEN for events beyond the @seq_num. It requests + * to be notified if and only if the event is of type @class_locale + */ +static int +megasas_register_aen(struct megasas_instance *instance, u32 seq_num, + u32 class_locale_word) +{ + int ret_val; + struct megasas_cmd *cmd; + struct megasas_dcmd_frame *dcmd; + union megasas_evt_class_locale curr_aen; + union megasas_evt_class_locale prev_aen; + + /* + * If there an AEN pending already (aen_cmd), check if the + * class_locale of that pending AEN is inclusive of the new + * AEN request we currently have. If it is, then we don't have + * to do anything. In other words, whichever events the current + * AEN request is subscribing to, have already been subscribed + * to. + * + * If the old_cmd is _not_ inclusive, then we have to abort + * that command, form a class_locale that is superset of both + * old and current and re-issue to the FW + */ + + curr_aen.word = class_locale_word; + + if (instance->aen_cmd) { + + prev_aen.word = instance->aen_cmd->frame->dcmd.mbox.w[1]; + + /* + * A class whose enum value is smaller is inclusive of all + * higher values. If a PROGRESS (= -1) was previously + * registered, then a new registration requests for higher + * classes need not be sent to FW. They are automatically + * included. + * + * Locale numbers don't have such hierarchy. They are bitmap + * values + */ + if ((prev_aen.members.class <= curr_aen.members.class) && + !((prev_aen.members.locale & curr_aen.members.locale) ^ + curr_aen.members.locale)) { + /* + * Previously issued event registration includes + * current request. Nothing to do. + */ + return 0; + } else { + curr_aen.members.locale |= prev_aen.members.locale; + + if (prev_aen.members.class < curr_aen.members.class) + curr_aen.members.class = prev_aen.members.class; + + instance->aen_cmd->abort_aen = 1; + ret_val = megasas_issue_blocked_abort_cmd(instance, + instance-> + aen_cmd); + + if (ret_val) { + printk(KERN_DEBUG "megasas: Failed to abort " + "previous AEN command\n"); + return ret_val; + } + } + } + + cmd = megasas_get_cmd(instance); + + if (!cmd) + return -ENOMEM; + + dcmd = &cmd->frame->dcmd; + + memset(instance->evt_detail, 0, sizeof(struct megasas_evt_detail)); + + /* + * Prepare DCMD for aen registration + */ + memset(dcmd->mbox.b, 0, MFI_MBOX_SIZE); + + dcmd->cmd = MFI_CMD_DCMD; + dcmd->cmd_status = 0x0; + dcmd->sge_count = 1; + dcmd->flags = MFI_FRAME_DIR_READ; + dcmd->timeout = 0; + dcmd->data_xfer_len = sizeof(struct megasas_evt_detail); + dcmd->opcode = MR_DCMD_CTRL_EVENT_WAIT; + dcmd->mbox.w[0] = seq_num; + dcmd->mbox.w[1] = curr_aen.word; + dcmd->sgl.sge32[0].phys_addr = (u32) instance->evt_detail_h; + dcmd->sgl.sge32[0].length = sizeof(struct megasas_evt_detail); + + /* + * Store reference to the cmd used to register for AEN. When an + * application wants us to register for AEN, we have to abort this + * cmd and re-register with a new EVENT LOCALE supplied by that app + */ + instance->aen_cmd = cmd; + + /* + * Issue the aen registration frame + */ + writel(cmd->frame_phys_addr >> 3, + &instance->reg_set->inbound_queue_port); + + return 0; +} + +/** + * megasas_start_aen - Subscribes to AEN during driver load time + * @instance: Adapter soft state + */ +static int megasas_start_aen(struct megasas_instance *instance) +{ + struct megasas_evt_log_info eli; + union megasas_evt_class_locale class_locale; + + /* + * Get the latest sequence number from FW + */ + memset(&eli, 0, sizeof(eli)); + + if (megasas_get_seq_num(instance, &eli)) + return -1; + + /* + * Register AEN with FW for latest sequence number plus 1 + */ + class_locale.members.reserved = 0; + class_locale.members.locale = MR_EVT_LOCALE_ALL; + class_locale.members.class = MR_EVT_CLASS_DEBUG; + + return megasas_register_aen(instance, eli.newest_seq_num + 1, + class_locale.word); +} + +/** + * megasas_io_attach - Attaches this driver to SCSI mid-layer + * @instance: Adapter soft state + */ +static int megasas_io_attach(struct megasas_instance *instance) +{ + struct Scsi_Host *host = instance->host; + + /* + * Export parameters required by SCSI mid-layer + */ + host->irq = instance->pdev->irq; + host->unique_id = instance->unique_id; + host->can_queue = instance->max_fw_cmds - MEGASAS_INT_CMDS; + host->this_id = instance->init_id; + host->sg_tablesize = instance->max_num_sge; + host->max_sectors = instance->max_sectors_per_req; + host->cmd_per_lun = 128; + host->max_channel = MEGASAS_MAX_CHANNELS - 1; + host->max_id = MEGASAS_MAX_DEV_PER_CHANNEL; + host->max_lun = MEGASAS_MAX_LUN; + + /* + * Notify the mid-layer about the new controller + */ + if (scsi_add_host(host, &instance->pdev->dev)) { + printk(KERN_DEBUG "megasas: scsi_add_host failed\n"); + return -ENODEV; + } + + /* + * Trigger SCSI to scan our drives + */ + scsi_scan_host(host); + return 0; +} + +/** + * megasas_probe_one - PCI hotplug entry point + * @pdev: PCI device structure + * @id: PCI ids of supported hotplugged adapter + */ +static int __devinit +megasas_probe_one(struct pci_dev *pdev, const struct pci_device_id *id) +{ + int rval; + struct Scsi_Host *host; + struct megasas_instance *instance; + + /* + * Announce PCI information + */ + printk(KERN_INFO "megasas: %#4.04x:%#4.04x:%#4.04x:%#4.04x: ", + pdev->vendor, pdev->device, pdev->subsystem_vendor, + pdev->subsystem_device); + + printk("bus %d:slot %d:func %d\n", + pdev->bus->number, PCI_SLOT(pdev->devfn), PCI_FUNC(pdev->devfn)); + + /* + * PCI prepping: enable device set bus mastering and dma mask + */ + rval = pci_enable_device(pdev); + + if (rval) { + return rval; + } + + pci_set_master(pdev); + + /* + * All our contollers are capable of performing 64-bit DMA + */ + if (IS_DMA64) { + if (pci_set_dma_mask(pdev, DMA_64BIT_MASK) != 0) { + + if (pci_set_dma_mask(pdev, DMA_32BIT_MASK) != 0) + goto fail_set_dma_mask; + } + } else { + if (pci_set_dma_mask(pdev, DMA_32BIT_MASK) != 0) + goto fail_set_dma_mask; + } + + host = scsi_host_alloc(&megasas_template, + sizeof(struct megasas_instance)); + + if (!host) { + printk(KERN_DEBUG "megasas: scsi_host_alloc failed\n"); + goto fail_alloc_instance; + } + + instance = (struct megasas_instance *)host->hostdata; + memset(instance, 0, sizeof(*instance)); + + instance->producer = pci_alloc_consistent(pdev, sizeof(u32), + &instance->producer_h); + instance->consumer = pci_alloc_consistent(pdev, sizeof(u32), + &instance->consumer_h); + + if (!instance->producer || !instance->consumer) { + printk(KERN_DEBUG "megasas: Failed to allocate memory for " + "producer, consumer\n"); + goto fail_alloc_dma_buf; + } + + *instance->producer = 0; + *instance->consumer = 0; + + instance->evt_detail = pci_alloc_consistent(pdev, + sizeof(struct + megasas_evt_detail), + &instance->evt_detail_h); + + if (!instance->evt_detail) { + printk(KERN_DEBUG "megasas: Failed to allocate memory for " + "event detail structure\n"); + goto fail_alloc_dma_buf; + } + + /* + * Initialize locks and queues + */ + INIT_LIST_HEAD(&instance->cmd_pool); + + init_waitqueue_head(&instance->int_cmd_wait_q); + init_waitqueue_head(&instance->abort_cmd_wait_q); + + spin_lock_init(&instance->cmd_pool_lock); + spin_lock_init(&instance->instance_lock); + + sema_init(&instance->aen_mutex, 1); + sema_init(&instance->ioctl_sem, MEGASAS_INT_CMDS); + + /* + * Initialize PCI related and misc parameters + */ + instance->pdev = pdev; + instance->host = host; + instance->unique_id = pdev->bus->number << 8 | pdev->devfn; + instance->init_id = MEGASAS_DEFAULT_INIT_ID; + + /* + * Initialize MFI Firmware + */ + if (megasas_init_mfi(instance)) + goto fail_init_mfi; + + /* + * Register IRQ + */ + if (request_irq(pdev->irq, megasas_isr, SA_SHIRQ, "megasas", instance)) { + printk(KERN_DEBUG "megasas: Failed to register IRQ\n"); + goto fail_irq; + } + + megasas_enable_intr(instance->reg_set); + + /* + * Store instance in PCI softstate + */ + pci_set_drvdata(pdev, instance); + + /* + * Add this controller to megasas_mgmt_info structure so that it + * can be exported to management applications + */ + megasas_mgmt_info.count++; + megasas_mgmt_info.instance[megasas_mgmt_info.max_index] = instance; + megasas_mgmt_info.max_index++; + + /* + * Initiate AEN (Asynchronous Event Notification) + */ + if (megasas_start_aen(instance)) { + printk(KERN_DEBUG "megasas: start aen failed\n"); + goto fail_start_aen; + } + + /* + * Register with SCSI mid-layer + */ + if (megasas_io_attach(instance)) + goto fail_io_attach; + + return 0; + + fail_start_aen: + fail_io_attach: + megasas_mgmt_info.count--; + megasas_mgmt_info.instance[megasas_mgmt_info.max_index] = NULL; + megasas_mgmt_info.max_index--; + + pci_set_drvdata(pdev, NULL); + megasas_disable_intr(instance->reg_set); + free_irq(instance->pdev->irq, instance); + + megasas_release_mfi(instance); + + fail_irq: + fail_init_mfi: + fail_alloc_dma_buf: + if (instance->evt_detail) + pci_free_consistent(pdev, sizeof(struct megasas_evt_detail), + instance->evt_detail, + instance->evt_detail_h); + + if (instance->producer) + pci_free_consistent(pdev, sizeof(u32), instance->producer, + instance->producer_h); + if (instance->consumer) + pci_free_consistent(pdev, sizeof(u32), instance->consumer, + instance->consumer_h); + scsi_host_put(host); + + fail_alloc_instance: + fail_set_dma_mask: + pci_disable_device(pdev); + + return -ENODEV; +} + +/** + * megasas_flush_cache - Requests FW to flush all its caches + * @instance: Adapter soft state + */ +static void megasas_flush_cache(struct megasas_instance *instance) +{ + struct megasas_cmd *cmd; + struct megasas_dcmd_frame *dcmd; + + cmd = megasas_get_cmd(instance); + + if (!cmd) + return; + + dcmd = &cmd->frame->dcmd; + + memset(dcmd->mbox.b, 0, MFI_MBOX_SIZE); + + dcmd->cmd = MFI_CMD_DCMD; + dcmd->cmd_status = 0x0; + dcmd->sge_count = 0; + dcmd->flags = MFI_FRAME_DIR_NONE; + dcmd->timeout = 0; + dcmd->data_xfer_len = 0; + dcmd->opcode = MR_DCMD_CTRL_CACHE_FLUSH; + dcmd->mbox.b[0] = MR_FLUSH_CTRL_CACHE | MR_FLUSH_DISK_CACHE; + + megasas_issue_blocked_cmd(instance, cmd); + + megasas_return_cmd(instance, cmd); + + return; +} + +/** + * megasas_shutdown_controller - Instructs FW to shutdown the controller + * @instance: Adapter soft state + */ +static void megasas_shutdown_controller(struct megasas_instance *instance) +{ + struct megasas_cmd *cmd; + struct megasas_dcmd_frame *dcmd; + + cmd = megasas_get_cmd(instance); + + if (!cmd) + return; + + if (instance->aen_cmd) + megasas_issue_blocked_abort_cmd(instance, instance->aen_cmd); + + dcmd = &cmd->frame->dcmd; + + memset(dcmd->mbox.b, 0, MFI_MBOX_SIZE); + + dcmd->cmd = MFI_CMD_DCMD; + dcmd->cmd_status = 0x0; + dcmd->sge_count = 0; + dcmd->flags = MFI_FRAME_DIR_NONE; + dcmd->timeout = 0; + dcmd->data_xfer_len = 0; + dcmd->opcode = MR_DCMD_CTRL_SHUTDOWN; + + megasas_issue_blocked_cmd(instance, cmd); + + megasas_return_cmd(instance, cmd); + + return; +} + +/** + * megasas_detach_one - PCI hot"un"plug entry point + * @pdev: PCI device structure + */ +static void megasas_detach_one(struct pci_dev *pdev) +{ + int i; + struct Scsi_Host *host; + struct megasas_instance *instance; + + instance = pci_get_drvdata(pdev); + host = instance->host; + + scsi_remove_host(instance->host); + megasas_flush_cache(instance); + megasas_shutdown_controller(instance); + + /* + * Take the instance off the instance array. Note that we will not + * decrement the max_index. We let this array be sparse array + */ + for (i = 0; i < megasas_mgmt_info.max_index; i++) { + if (megasas_mgmt_info.instance[i] == instance) { + megasas_mgmt_info.count--; + megasas_mgmt_info.instance[i] = NULL; + + break; + } + } + + pci_set_drvdata(instance->pdev, NULL); + + megasas_disable_intr(instance->reg_set); + + free_irq(instance->pdev->irq, instance); + + megasas_release_mfi(instance); + + pci_free_consistent(pdev, sizeof(struct megasas_evt_detail), + instance->evt_detail, instance->evt_detail_h); + + pci_free_consistent(pdev, sizeof(u32), instance->producer, + instance->producer_h); + + pci_free_consistent(pdev, sizeof(u32), instance->consumer, + instance->consumer_h); + + scsi_host_put(host); + + pci_set_drvdata(pdev, NULL); + + pci_disable_device(pdev); + + return; +} + +/** + * megasas_shutdown - Shutdown entry point + * @device: Generic device structure + */ +static void megasas_shutdown(struct pci_dev *pdev) +{ + struct megasas_instance *instance = pci_get_drvdata(pdev); + megasas_flush_cache(instance); +} + +/** + * megasas_mgmt_open - char node "open" entry point + */ +static int megasas_mgmt_open(struct inode *inode, struct file *filep) +{ + /* + * Allow only those users with admin rights + */ + if (!capable(CAP_SYS_ADMIN)) + return -EACCES; + + return 0; +} + +/** + * megasas_mgmt_release - char node "release" entry point + */ +static int megasas_mgmt_release(struct inode *inode, struct file *filep) +{ + filep->private_data = NULL; + fasync_helper(-1, filep, 0, &megasas_async_queue); + + return 0; +} + +/** + * megasas_mgmt_fasync - Async notifier registration from applications + * + * This function adds the calling process to a driver global queue. When an + * event occurs, SIGIO will be sent to all processes in this queue. + */ +static int megasas_mgmt_fasync(int fd, struct file *filep, int mode) +{ + int rc; + + down(&megasas_async_queue_mutex); + + rc = fasync_helper(fd, filep, mode, &megasas_async_queue); + + up(&megasas_async_queue_mutex); + + if (rc >= 0) { + /* For sanity check when we get ioctl */ + filep->private_data = filep; + return 0; + } + + printk(KERN_DEBUG "megasas: fasync_helper failed [%d]\n", rc); + + return rc; +} + +/** + * megasas_mgmt_fw_ioctl - Issues management ioctls to FW + * @instance: Adapter soft state + * @argp: User's ioctl packet + */ +static int +megasas_mgmt_fw_ioctl(struct megasas_instance *instance, + struct megasas_iocpacket __user * user_ioc, + struct megasas_iocpacket *ioc) +{ + struct megasas_sge32 *kern_sge32; + struct megasas_cmd *cmd; + void *kbuff_arr[MAX_IOCTL_SGE]; + dma_addr_t buf_handle = 0; + int error = 0, i; + void *sense = NULL; + dma_addr_t sense_handle; + u32 *sense_ptr; + + memset(kbuff_arr, 0, sizeof(kbuff_arr)); + + if (ioc->sge_count > MAX_IOCTL_SGE) { + printk(KERN_DEBUG "megasas: SGE count [%d] > max limit [%d]\n", + ioc->sge_count, MAX_IOCTL_SGE); + return -EINVAL; + } + + cmd = megasas_get_cmd(instance); + if (!cmd) { + printk(KERN_DEBUG "megasas: Failed to get a cmd packet\n"); + return -ENOMEM; + } + + /* + * User's IOCTL packet has 2 frames (maximum). Copy those two + * frames into our cmd's frames. cmd->frame's context will get + * overwritten when we copy from user's frames. So set that value + * alone separately + */ + memcpy(cmd->frame, ioc->frame.raw, 2 * MEGAMFI_FRAME_SIZE); + cmd->frame->hdr.context = cmd->index; + + /* + * The management interface between applications and the fw uses + * MFI frames. E.g, RAID configuration changes, LD property changes + * etc are accomplishes through different kinds of MFI frames. The + * driver needs to care only about substituting user buffers with + * kernel buffers in SGLs. The location of SGL is embedded in the + * struct iocpacket itself. + */ + kern_sge32 = (struct megasas_sge32 *) + ((unsigned long)cmd->frame + ioc->sgl_off); + + /* + * For each user buffer, create a mirror buffer and copy in + */ + for (i = 0; i < ioc->sge_count; i++) { + kbuff_arr[i] = pci_alloc_consistent(instance->pdev, + ioc->sgl[i].iov_len, + &buf_handle); + if (!kbuff_arr[i]) { + printk(KERN_DEBUG "megasas: Failed to alloc " + "kernel SGL buffer for IOCTL \n"); + error = -ENOMEM; + goto out; + } + + /* + * We don't change the dma_coherent_mask, so + * pci_alloc_consistent only returns 32bit addresses + */ + kern_sge32[i].phys_addr = (u32) buf_handle; + kern_sge32[i].length = ioc->sgl[i].iov_len; + + /* + * We created a kernel buffer corresponding to the + * user buffer. Now copy in from the user buffer + */ + if (copy_from_user(kbuff_arr[i], ioc->sgl[i].iov_base, + (u32) (ioc->sgl[i].iov_len))) { + error = -EFAULT; + goto out; + } + } + + if (ioc->sense_len) { + sense = pci_alloc_consistent(instance->pdev, ioc->sense_len, + &sense_handle); + if (!sense) { + error = -ENOMEM; + goto out; + } + + sense_ptr = + (u32 *) ((unsigned long)cmd->frame + ioc->sense_off); + *sense_ptr = sense_handle; + } + + /* + * Set the sync_cmd flag so that the ISR knows not to complete this + * cmd to the SCSI mid-layer + */ + cmd->sync_cmd = 1; + megasas_issue_blocked_cmd(instance, cmd); + cmd->sync_cmd = 0; + + /* + * copy out the kernel buffers to user buffers + */ + for (i = 0; i < ioc->sge_count; i++) { + if (copy_to_user(ioc->sgl[i].iov_base, kbuff_arr[i], + ioc->sgl[i].iov_len)) { + error = -EFAULT; + goto out; + } + } + + /* + * copy out the sense + */ + if (ioc->sense_len) { + /* + * sense_ptr points to the location that has the user + * sense buffer address + */ + sense_ptr = (u32 *) ((unsigned long)ioc->frame.raw + + ioc->sense_off); + + if (copy_to_user((void __user *)((unsigned long)(*sense_ptr)), + sense, ioc->sense_len)) { + error = -EFAULT; + goto out; + } + } + + /* + * copy the status codes returned by the fw + */ + if (copy_to_user(&user_ioc->frame.hdr.cmd_status, + &cmd->frame->hdr.cmd_status, sizeof(u8))) { + printk(KERN_DEBUG "megasas: Error copying out cmd_status\n"); + error = -EFAULT; + } + + out: + if (sense) { + pci_free_consistent(instance->pdev, ioc->sense_len, + sense, sense_handle); + } + + for (i = 0; i < ioc->sge_count && kbuff_arr[i]; i++) { + pci_free_consistent(instance->pdev, + kern_sge32[i].length, + kbuff_arr[i], kern_sge32[i].phys_addr); + } + + megasas_return_cmd(instance, cmd); + return error; +} + +static struct megasas_instance *megasas_lookup_instance(u16 host_no) +{ + int i; + + for (i = 0; i < megasas_mgmt_info.max_index; i++) { + + if ((megasas_mgmt_info.instance[i]) && + (megasas_mgmt_info.instance[i]->host->host_no == host_no)) + return megasas_mgmt_info.instance[i]; + } + + return NULL; +} + +static int megasas_mgmt_ioctl_fw(struct file *file, unsigned long arg) +{ + struct megasas_iocpacket __user *user_ioc = + (struct megasas_iocpacket __user *)arg; + struct megasas_iocpacket *ioc; + struct megasas_instance *instance; + int error; + + ioc = kmalloc(sizeof(*ioc), GFP_KERNEL); + if (!ioc) + return -ENOMEM; + + if (copy_from_user(ioc, user_ioc, sizeof(*ioc))) { + error = -EFAULT; + goto out_kfree_ioc; + } + + instance = megasas_lookup_instance(ioc->host_no); + if (!instance) { + error = -ENODEV; + goto out_kfree_ioc; + } + + /* + * We will allow only MEGASAS_INT_CMDS number of parallel ioctl cmds + */ + if (down_interruptible(&instance->ioctl_sem)) { + error = -ERESTARTSYS; + goto out_kfree_ioc; + } + error = megasas_mgmt_fw_ioctl(instance, user_ioc, ioc); + up(&instance->ioctl_sem); + + out_kfree_ioc: + kfree(ioc); + return error; +} + +static int megasas_mgmt_ioctl_aen(struct file *file, unsigned long arg) +{ + struct megasas_instance *instance; + struct megasas_aen aen; + int error; + + if (file->private_data != file) { + printk(KERN_DEBUG "megasas: fasync_helper was not " + "called first\n"); + return -EINVAL; + } + + if (copy_from_user(&aen, (void __user *)arg, sizeof(aen))) + return -EFAULT; + + instance = megasas_lookup_instance(aen.host_no); + + if (!instance) + return -ENODEV; + + down(&instance->aen_mutex); + error = megasas_register_aen(instance, aen.seq_num, + aen.class_locale_word); + up(&instance->aen_mutex); + return error; +} + +/** + * megasas_mgmt_ioctl - char node ioctl entry point + */ +static long +megasas_mgmt_ioctl(struct file *file, unsigned int cmd, unsigned long arg) +{ + switch (cmd) { + case MEGASAS_IOC_FIRMWARE: + return megasas_mgmt_ioctl_fw(file, arg); + + case MEGASAS_IOC_GET_AEN: + return megasas_mgmt_ioctl_aen(file, arg); + } + + return -ENOTTY; +} + +#ifdef CONFIG_COMPAT +static int megasas_mgmt_compat_ioctl_fw(struct file *file, unsigned long arg) +{ + struct compat_megasas_iocpacket __user *cioc = + (struct compat_megasas_iocpacket __user *)arg; + struct megasas_iocpacket __user *ioc = + compat_alloc_user_space(sizeof(struct megasas_iocpacket)); + int i; + int error = 0; + + clear_user(ioc, sizeof(*ioc)); + + if (copy_in_user(&ioc->host_no, &cioc->host_no, sizeof(u16)) || + copy_in_user(&ioc->sgl_off, &cioc->sgl_off, sizeof(u32)) || + copy_in_user(&ioc->sense_off, &cioc->sense_off, sizeof(u32)) || + copy_in_user(&ioc->sense_len, &cioc->sense_len, sizeof(u32)) || + copy_in_user(ioc->frame.raw, cioc->frame.raw, 128) || + copy_in_user(&ioc->sge_count, &cioc->sge_count, sizeof(u32))) + return -EFAULT; + + for (i = 0; i < MAX_IOCTL_SGE; i++) { + compat_uptr_t ptr; + + if (get_user(ptr, &cioc->sgl[i].iov_base) || + put_user(compat_ptr(ptr), &ioc->sgl[i].iov_base) || + copy_in_user(&ioc->sgl[i].iov_len, + &cioc->sgl[i].iov_len, sizeof(compat_size_t))) + return -EFAULT; + } + + error = megasas_mgmt_ioctl_fw(file, (unsigned long)ioc); + + if (copy_in_user(&cioc->frame.hdr.cmd_status, + &ioc->frame.hdr.cmd_status, sizeof(u8))) { + printk(KERN_DEBUG "megasas: error copy_in_user cmd_status\n"); + return -EFAULT; + } + return error; +} + +static long +megasas_mgmt_compat_ioctl(struct file *file, unsigned int cmd, + unsigned long arg) +{ + switch (cmd) { + case MEGASAS_IOC_FIRMWARE:{ + return megasas_mgmt_compat_ioctl_fw(file, arg); + } + case MEGASAS_IOC_GET_AEN: + return megasas_mgmt_ioctl_aen(file, arg); + } + + return -ENOTTY; +} +#endif + +/* + * File operations structure for management interface + */ +static struct file_operations megasas_mgmt_fops = { + .owner = THIS_MODULE, + .open = megasas_mgmt_open, + .release = megasas_mgmt_release, + .fasync = megasas_mgmt_fasync, + .unlocked_ioctl = megasas_mgmt_ioctl, +#ifdef CONFIG_COMPAT + .compat_ioctl = megasas_mgmt_compat_ioctl, +#endif +}; + +/* + * PCI hotplug support registration structure + */ +static struct pci_driver megasas_pci_driver = { + + .name = "megaraid_sas", + .id_table = megasas_pci_table, + .probe = megasas_probe_one, + .remove = __devexit_p(megasas_detach_one), + .shutdown = megasas_shutdown, +}; + +/* + * Sysfs driver attributes + */ +static ssize_t megasas_sysfs_show_version(struct device_driver *dd, char *buf) +{ + return snprintf(buf, strlen(MEGASAS_VERSION) + 2, "%s\n", + MEGASAS_VERSION); +} + +static DRIVER_ATTR(version, S_IRUGO, megasas_sysfs_show_version, NULL); + +static ssize_t +megasas_sysfs_show_release_date(struct device_driver *dd, char *buf) +{ + return snprintf(buf, strlen(MEGASAS_RELDATE) + 2, "%s\n", + MEGASAS_RELDATE); +} + +static DRIVER_ATTR(release_date, S_IRUGO, megasas_sysfs_show_release_date, + NULL); + +/** + * megasas_init - Driver load entry point + */ +static int __init megasas_init(void) +{ + int rval; + + /* + * Announce driver version and other information + */ + printk(KERN_INFO "megasas: %s %s\n", MEGASAS_VERSION, + MEGASAS_EXT_VERSION); + + memset(&megasas_mgmt_info, 0, sizeof(megasas_mgmt_info)); + + /* + * Register character device node + */ + rval = register_chrdev(0, "megaraid_sas_ioctl", &megasas_mgmt_fops); + + if (rval < 0) { + printk(KERN_DEBUG "megasas: failed to open device node\n"); + return rval; + } + + megasas_mgmt_majorno = rval; + + /* + * Register ourselves as PCI hotplug module + */ + rval = pci_module_init(&megasas_pci_driver); + + if (rval) { + printk(KERN_DEBUG "megasas: PCI hotplug regisration failed \n"); + unregister_chrdev(megasas_mgmt_majorno, "megaraid_sas_ioctl"); + } + + driver_create_file(&megasas_pci_driver.driver, &driver_attr_version); + driver_create_file(&megasas_pci_driver.driver, + &driver_attr_release_date); + + return rval; +} + +/** + * megasas_exit - Driver unload entry point + */ +static void __exit megasas_exit(void) +{ + driver_remove_file(&megasas_pci_driver.driver, &driver_attr_version); + driver_remove_file(&megasas_pci_driver.driver, + &driver_attr_release_date); + + pci_unregister_driver(&megasas_pci_driver); + unregister_chrdev(megasas_mgmt_majorno, "megaraid_sas_ioctl"); +} + +module_init(megasas_init); +module_exit(megasas_exit); diff --git a/drivers/scsi/megaraid/megaraid_sas.h b/drivers/scsi/megaraid/megaraid_sas.h new file mode 100644 index 00000000000..eaec9d53142 --- /dev/null +++ b/drivers/scsi/megaraid/megaraid_sas.h @@ -0,0 +1,1142 @@ +/* + * + * Linux MegaRAID driver for SAS based RAID controllers + * + * Copyright (c) 2003-2005 LSI Logic Corporation. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * FILE : megaraid_sas.h + */ + +#ifndef LSI_MEGARAID_SAS_H +#define LSI_MEGARAID_SAS_H + +/** + * MegaRAID SAS Driver meta data + */ +#define MEGASAS_VERSION "00.00.02.00-rc4" +#define MEGASAS_RELDATE "Sep 16, 2005" +#define MEGASAS_EXT_VERSION "Fri Sep 16 12:37:08 EDT 2005" + +/* + * ===================================== + * MegaRAID SAS MFI firmware definitions + * ===================================== + */ + +/* + * MFI stands for MegaRAID SAS FW Interface. This is just a moniker for + * protocol between the software and firmware. Commands are issued using + * "message frames" + */ + +/** + * FW posts its state in upper 4 bits of outbound_msg_0 register + */ +#define MFI_STATE_MASK 0xF0000000 +#define MFI_STATE_UNDEFINED 0x00000000 +#define MFI_STATE_BB_INIT 0x10000000 +#define MFI_STATE_FW_INIT 0x40000000 +#define MFI_STATE_WAIT_HANDSHAKE 0x60000000 +#define MFI_STATE_FW_INIT_2 0x70000000 +#define MFI_STATE_DEVICE_SCAN 0x80000000 +#define MFI_STATE_FLUSH_CACHE 0xA0000000 +#define MFI_STATE_READY 0xB0000000 +#define MFI_STATE_OPERATIONAL 0xC0000000 +#define MFI_STATE_FAULT 0xF0000000 + +#define MEGAMFI_FRAME_SIZE 64 + +/** + * During FW init, clear pending cmds & reset state using inbound_msg_0 + * + * ABORT : Abort all pending cmds + * READY : Move from OPERATIONAL to READY state; discard queue info + * MFIMODE : Discard (possible) low MFA posted in 64-bit mode (??) + * CLR_HANDSHAKE: FW is waiting for HANDSHAKE from BIOS or Driver + */ +#define MFI_INIT_ABORT 0x00000000 +#define MFI_INIT_READY 0x00000002 +#define MFI_INIT_MFIMODE 0x00000004 +#define MFI_INIT_CLEAR_HANDSHAKE 0x00000008 +#define MFI_RESET_FLAGS MFI_INIT_READY|MFI_INIT_MFIMODE + +/** + * MFI frame flags + */ +#define MFI_FRAME_POST_IN_REPLY_QUEUE 0x0000 +#define MFI_FRAME_DONT_POST_IN_REPLY_QUEUE 0x0001 +#define MFI_FRAME_SGL32 0x0000 +#define MFI_FRAME_SGL64 0x0002 +#define MFI_FRAME_SENSE32 0x0000 +#define MFI_FRAME_SENSE64 0x0004 +#define MFI_FRAME_DIR_NONE 0x0000 +#define MFI_FRAME_DIR_WRITE 0x0008 +#define MFI_FRAME_DIR_READ 0x0010 +#define MFI_FRAME_DIR_BOTH 0x0018 + +/** + * Definition for cmd_status + */ +#define MFI_CMD_STATUS_POLL_MODE 0xFF + +/** + * MFI command opcodes + */ +#define MFI_CMD_INIT 0x00 +#define MFI_CMD_LD_READ 0x01 +#define MFI_CMD_LD_WRITE 0x02 +#define MFI_CMD_LD_SCSI_IO 0x03 +#define MFI_CMD_PD_SCSI_IO 0x04 +#define MFI_CMD_DCMD 0x05 +#define MFI_CMD_ABORT 0x06 +#define MFI_CMD_SMP 0x07 +#define MFI_CMD_STP 0x08 + +#define MR_DCMD_CTRL_GET_INFO 0x01010000 + +#define MR_DCMD_CTRL_CACHE_FLUSH 0x01101000 +#define MR_FLUSH_CTRL_CACHE 0x01 +#define MR_FLUSH_DISK_CACHE 0x02 + +#define MR_DCMD_CTRL_SHUTDOWN 0x01050000 +#define MR_ENABLE_DRIVE_SPINDOWN 0x01 + +#define MR_DCMD_CTRL_EVENT_GET_INFO 0x01040100 +#define MR_DCMD_CTRL_EVENT_GET 0x01040300 +#define MR_DCMD_CTRL_EVENT_WAIT 0x01040500 +#define MR_DCMD_LD_GET_PROPERTIES 0x03030000 + +#define MR_DCMD_CLUSTER 0x08000000 +#define MR_DCMD_CLUSTER_RESET_ALL 0x08010100 +#define MR_DCMD_CLUSTER_RESET_LD 0x08010200 + +/** + * MFI command completion codes + */ +enum MFI_STAT { + MFI_STAT_OK = 0x00, + MFI_STAT_INVALID_CMD = 0x01, + MFI_STAT_INVALID_DCMD = 0x02, + MFI_STAT_INVALID_PARAMETER = 0x03, + MFI_STAT_INVALID_SEQUENCE_NUMBER = 0x04, + MFI_STAT_ABORT_NOT_POSSIBLE = 0x05, + MFI_STAT_APP_HOST_CODE_NOT_FOUND = 0x06, + MFI_STAT_APP_IN_USE = 0x07, + MFI_STAT_APP_NOT_INITIALIZED = 0x08, + MFI_STAT_ARRAY_INDEX_INVALID = 0x09, + MFI_STAT_ARRAY_ROW_NOT_EMPTY = 0x0a, + MFI_STAT_CONFIG_RESOURCE_CONFLICT = 0x0b, + MFI_STAT_DEVICE_NOT_FOUND = 0x0c, + MFI_STAT_DRIVE_TOO_SMALL = 0x0d, + MFI_STAT_FLASH_ALLOC_FAIL = 0x0e, + MFI_STAT_FLASH_BUSY = 0x0f, + MFI_STAT_FLASH_ERROR = 0x10, + MFI_STAT_FLASH_IMAGE_BAD = 0x11, + MFI_STAT_FLASH_IMAGE_INCOMPLETE = 0x12, + MFI_STAT_FLASH_NOT_OPEN = 0x13, + MFI_STAT_FLASH_NOT_STARTED = 0x14, + MFI_STAT_FLUSH_FAILED = 0x15, + MFI_STAT_HOST_CODE_NOT_FOUNT = 0x16, + MFI_STAT_LD_CC_IN_PROGRESS = 0x17, + MFI_STAT_LD_INIT_IN_PROGRESS = 0x18, + MFI_STAT_LD_LBA_OUT_OF_RANGE = 0x19, + MFI_STAT_LD_MAX_CONFIGURED = 0x1a, + MFI_STAT_LD_NOT_OPTIMAL = 0x1b, + MFI_STAT_LD_RBLD_IN_PROGRESS = 0x1c, + MFI_STAT_LD_RECON_IN_PROGRESS = 0x1d, + MFI_STAT_LD_WRONG_RAID_LEVEL = 0x1e, + MFI_STAT_MAX_SPARES_EXCEEDED = 0x1f, + MFI_STAT_MEMORY_NOT_AVAILABLE = 0x20, + MFI_STAT_MFC_HW_ERROR = 0x21, + MFI_STAT_NO_HW_PRESENT = 0x22, + MFI_STAT_NOT_FOUND = 0x23, + MFI_STAT_NOT_IN_ENCL = 0x24, + MFI_STAT_PD_CLEAR_IN_PROGRESS = 0x25, + MFI_STAT_PD_TYPE_WRONG = 0x26, + MFI_STAT_PR_DISABLED = 0x27, + MFI_STAT_ROW_INDEX_INVALID = 0x28, + MFI_STAT_SAS_CONFIG_INVALID_ACTION = 0x29, + MFI_STAT_SAS_CONFIG_INVALID_DATA = 0x2a, + MFI_STAT_SAS_CONFIG_INVALID_PAGE = 0x2b, + MFI_STAT_SAS_CONFIG_INVALID_TYPE = 0x2c, + MFI_STAT_SCSI_DONE_WITH_ERROR = 0x2d, + MFI_STAT_SCSI_IO_FAILED = 0x2e, + MFI_STAT_SCSI_RESERVATION_CONFLICT = 0x2f, + MFI_STAT_SHUTDOWN_FAILED = 0x30, + MFI_STAT_TIME_NOT_SET = 0x31, + MFI_STAT_WRONG_STATE = 0x32, + MFI_STAT_LD_OFFLINE = 0x33, + MFI_STAT_PEER_NOTIFICATION_REJECTED = 0x34, + MFI_STAT_PEER_NOTIFICATION_FAILED = 0x35, + MFI_STAT_RESERVATION_IN_PROGRESS = 0x36, + MFI_STAT_I2C_ERRORS_DETECTED = 0x37, + MFI_STAT_PCI_ERRORS_DETECTED = 0x38, + + MFI_STAT_INVALID_STATUS = 0xFF +}; + +/* + * Number of mailbox bytes in DCMD message frame + */ +#define MFI_MBOX_SIZE 12 + +enum MR_EVT_CLASS { + + MR_EVT_CLASS_DEBUG = -2, + MR_EVT_CLASS_PROGRESS = -1, + MR_EVT_CLASS_INFO = 0, + MR_EVT_CLASS_WARNING = 1, + MR_EVT_CLASS_CRITICAL = 2, + MR_EVT_CLASS_FATAL = 3, + MR_EVT_CLASS_DEAD = 4, + +}; + +enum MR_EVT_LOCALE { + + MR_EVT_LOCALE_LD = 0x0001, + MR_EVT_LOCALE_PD = 0x0002, + MR_EVT_LOCALE_ENCL = 0x0004, + MR_EVT_LOCALE_BBU = 0x0008, + MR_EVT_LOCALE_SAS = 0x0010, + MR_EVT_LOCALE_CTRL = 0x0020, + MR_EVT_LOCALE_CONFIG = 0x0040, + MR_EVT_LOCALE_CLUSTER = 0x0080, + MR_EVT_LOCALE_ALL = 0xffff, + +}; + +enum MR_EVT_ARGS { + + MR_EVT_ARGS_NONE, + MR_EVT_ARGS_CDB_SENSE, + MR_EVT_ARGS_LD, + MR_EVT_ARGS_LD_COUNT, + MR_EVT_ARGS_LD_LBA, + MR_EVT_ARGS_LD_OWNER, + MR_EVT_ARGS_LD_LBA_PD_LBA, + MR_EVT_ARGS_LD_PROG, + MR_EVT_ARGS_LD_STATE, + MR_EVT_ARGS_LD_STRIP, + MR_EVT_ARGS_PD, + MR_EVT_ARGS_PD_ERR, + MR_EVT_ARGS_PD_LBA, + MR_EVT_ARGS_PD_LBA_LD, + MR_EVT_ARGS_PD_PROG, + MR_EVT_ARGS_PD_STATE, + MR_EVT_ARGS_PCI, + MR_EVT_ARGS_RATE, + MR_EVT_ARGS_STR, + MR_EVT_ARGS_TIME, + MR_EVT_ARGS_ECC, + +}; + +/* + * SAS controller properties + */ +struct megasas_ctrl_prop { + + u16 seq_num; + u16 pred_fail_poll_interval; + u16 intr_throttle_count; + u16 intr_throttle_timeouts; + u8 rebuild_rate; + u8 patrol_read_rate; + u8 bgi_rate; + u8 cc_rate; + u8 recon_rate; + u8 cache_flush_interval; + u8 spinup_drv_count; + u8 spinup_delay; + u8 cluster_enable; + u8 coercion_mode; + u8 alarm_enable; + u8 disable_auto_rebuild; + u8 disable_battery_warn; + u8 ecc_bucket_size; + u16 ecc_bucket_leak_rate; + u8 restore_hotspare_on_insertion; + u8 expose_encl_devices; + u8 reserved[38]; + +} __attribute__ ((packed)); + +/* + * SAS controller information + */ +struct megasas_ctrl_info { + + /* + * PCI device information + */ + struct { + + u16 vendor_id; + u16 device_id; + u16 sub_vendor_id; + u16 sub_device_id; + u8 reserved[24]; + + } __attribute__ ((packed)) pci; + + /* + * Host interface information + */ + struct { + + u8 PCIX:1; + u8 PCIE:1; + u8 iSCSI:1; + u8 SAS_3G:1; + u8 reserved_0:4; + u8 reserved_1[6]; + u8 port_count; + u64 port_addr[8]; + + } __attribute__ ((packed)) host_interface; + + /* + * Device (backend) interface information + */ + struct { + + u8 SPI:1; + u8 SAS_3G:1; + u8 SATA_1_5G:1; + u8 SATA_3G:1; + u8 reserved_0:4; + u8 reserved_1[6]; + u8 port_count; + u64 port_addr[8]; + + } __attribute__ ((packed)) device_interface; + + /* + * List of components residing in flash. All str are null terminated + */ + u32 image_check_word; + u32 image_component_count; + + struct { + + char name[8]; + char version[32]; + char build_date[16]; + char built_time[16]; + + } __attribute__ ((packed)) image_component[8]; + + /* + * List of flash components that have been flashed on the card, but + * are not in use, pending reset of the adapter. This list will be + * empty if a flash operation has not occurred. All stings are null + * terminated + */ + u32 pending_image_component_count; + + struct { + + char name[8]; + char version[32]; + char build_date[16]; + char build_time[16]; + + } __attribute__ ((packed)) pending_image_component[8]; + + u8 max_arms; + u8 max_spans; + u8 max_arrays; + u8 max_lds; + + char product_name[80]; + char serial_no[32]; + + /* + * Other physical/controller/operation information. Indicates the + * presence of the hardware + */ + struct { + + u32 bbu:1; + u32 alarm:1; + u32 nvram:1; + u32 uart:1; + u32 reserved:28; + + } __attribute__ ((packed)) hw_present; + + u32 current_fw_time; + + /* + * Maximum data transfer sizes + */ + u16 max_concurrent_cmds; + u16 max_sge_count; + u32 max_request_size; + + /* + * Logical and physical device counts + */ + u16 ld_present_count; + u16 ld_degraded_count; + u16 ld_offline_count; + + u16 pd_present_count; + u16 pd_disk_present_count; + u16 pd_disk_pred_failure_count; + u16 pd_disk_failed_count; + + /* + * Memory size information + */ + u16 nvram_size; + u16 memory_size; + u16 flash_size; + + /* + * Error counters + */ + u16 mem_correctable_error_count; + u16 mem_uncorrectable_error_count; + + /* + * Cluster information + */ + u8 cluster_permitted; + u8 cluster_active; + + /* + * Additional max data transfer sizes + */ + u16 max_strips_per_io; + + /* + * Controller capabilities structures + */ + struct { + + u32 raid_level_0:1; + u32 raid_level_1:1; + u32 raid_level_5:1; + u32 raid_level_1E:1; + u32 raid_level_6:1; + u32 reserved:27; + + } __attribute__ ((packed)) raid_levels; + + struct { + + u32 rbld_rate:1; + u32 cc_rate:1; + u32 bgi_rate:1; + u32 recon_rate:1; + u32 patrol_rate:1; + u32 alarm_control:1; + u32 cluster_supported:1; + u32 bbu:1; + u32 spanning_allowed:1; + u32 dedicated_hotspares:1; + u32 revertible_hotspares:1; + u32 foreign_config_import:1; + u32 self_diagnostic:1; + u32 mixed_redundancy_arr:1; + u32 global_hot_spares:1; + u32 reserved:17; + + } __attribute__ ((packed)) adapter_operations; + + struct { + + u32 read_policy:1; + u32 write_policy:1; + u32 io_policy:1; + u32 access_policy:1; + u32 disk_cache_policy:1; + u32 reserved:27; + + } __attribute__ ((packed)) ld_operations; + + struct { + + u8 min; + u8 max; + u8 reserved[2]; + + } __attribute__ ((packed)) stripe_sz_ops; + + struct { + + u32 force_online:1; + u32 force_offline:1; + u32 force_rebuild:1; + u32 reserved:29; + + } __attribute__ ((packed)) pd_operations; + + struct { + + u32 ctrl_supports_sas:1; + u32 ctrl_supports_sata:1; + u32 allow_mix_in_encl:1; + u32 allow_mix_in_ld:1; + u32 allow_sata_in_cluster:1; + u32 reserved:27; + + } __attribute__ ((packed)) pd_mix_support; + + /* + * Define ECC single-bit-error bucket information + */ + u8 ecc_bucket_count; + u8 reserved_2[11]; + + /* + * Include the controller properties (changeable items) + */ + struct megasas_ctrl_prop properties; + + /* + * Define FW pkg version (set in envt v'bles on OEM basis) + */ + char package_version[0x60]; + + u8 pad[0x800 - 0x6a0]; + +} __attribute__ ((packed)); + +/* + * =============================== + * MegaRAID SAS driver definitions + * =============================== + */ +#define MEGASAS_MAX_PD_CHANNELS 2 +#define MEGASAS_MAX_LD_CHANNELS 2 +#define MEGASAS_MAX_CHANNELS (MEGASAS_MAX_PD_CHANNELS + \ + MEGASAS_MAX_LD_CHANNELS) +#define MEGASAS_MAX_DEV_PER_CHANNEL 128 +#define MEGASAS_DEFAULT_INIT_ID -1 +#define MEGASAS_MAX_LUN 8 +#define MEGASAS_MAX_LD 64 + +/* + * When SCSI mid-layer calls driver's reset routine, driver waits for + * MEGASAS_RESET_WAIT_TIME seconds for all outstanding IO to complete. Note + * that the driver cannot _actually_ abort or reset pending commands. While + * it is waiting for the commands to complete, it prints a diagnostic message + * every MEGASAS_RESET_NOTICE_INTERVAL seconds + */ +#define MEGASAS_RESET_WAIT_TIME 180 +#define MEGASAS_RESET_NOTICE_INTERVAL 5 + +#define MEGASAS_IOCTL_CMD 0 + +/* + * FW reports the maximum of number of commands that it can accept (maximum + * commands that can be outstanding) at any time. The driver must report a + * lower number to the mid layer because it can issue a few internal commands + * itself (E.g, AEN, abort cmd, IOCTLs etc). The number of commands it needs + * is shown below + */ +#define MEGASAS_INT_CMDS 32 + +/* + * FW can accept both 32 and 64 bit SGLs. We want to allocate 32/64 bit + * SGLs based on the size of dma_addr_t + */ +#define IS_DMA64 (sizeof(dma_addr_t) == 8) + +#define MFI_OB_INTR_STATUS_MASK 0x00000002 +#define MFI_POLL_TIMEOUT_SECS 10 + +struct megasas_register_set { + + u32 reserved_0[4]; /*0000h */ + + u32 inbound_msg_0; /*0010h */ + u32 inbound_msg_1; /*0014h */ + u32 outbound_msg_0; /*0018h */ + u32 outbound_msg_1; /*001Ch */ + + u32 inbound_doorbell; /*0020h */ + u32 inbound_intr_status; /*0024h */ + u32 inbound_intr_mask; /*0028h */ + + u32 outbound_doorbell; /*002Ch */ + u32 outbound_intr_status; /*0030h */ + u32 outbound_intr_mask; /*0034h */ + + u32 reserved_1[2]; /*0038h */ + + u32 inbound_queue_port; /*0040h */ + u32 outbound_queue_port; /*0044h */ + + u32 reserved_2; /*004Ch */ + + u32 index_registers[1004]; /*0050h */ + +} __attribute__ ((packed)); + +struct megasas_sge32 { + + u32 phys_addr; + u32 length; + +} __attribute__ ((packed)); + +struct megasas_sge64 { + + u64 phys_addr; + u32 length; + +} __attribute__ ((packed)); + +union megasas_sgl { + + struct megasas_sge32 sge32[1]; + struct megasas_sge64 sge64[1]; + +} __attribute__ ((packed)); + +struct megasas_header { + + u8 cmd; /*00h */ + u8 sense_len; /*01h */ + u8 cmd_status; /*02h */ + u8 scsi_status; /*03h */ + + u8 target_id; /*04h */ + u8 lun; /*05h */ + u8 cdb_len; /*06h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + u32 data_xferlen; /*14h */ + +} __attribute__ ((packed)); + +union megasas_sgl_frame { + + struct megasas_sge32 sge32[8]; + struct megasas_sge64 sge64[5]; + +} __attribute__ ((packed)); + +struct megasas_init_frame { + + u8 cmd; /*00h */ + u8 reserved_0; /*01h */ + u8 cmd_status; /*02h */ + + u8 reserved_1; /*03h */ + u32 reserved_2; /*04h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 reserved_3; /*12h */ + u32 data_xfer_len; /*14h */ + + u32 queue_info_new_phys_addr_lo; /*18h */ + u32 queue_info_new_phys_addr_hi; /*1Ch */ + u32 queue_info_old_phys_addr_lo; /*20h */ + u32 queue_info_old_phys_addr_hi; /*24h */ + + u32 reserved_4[6]; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_init_queue_info { + + u32 init_flags; /*00h */ + u32 reply_queue_entries; /*04h */ + + u32 reply_queue_start_phys_addr_lo; /*08h */ + u32 reply_queue_start_phys_addr_hi; /*0Ch */ + u32 producer_index_phys_addr_lo; /*10h */ + u32 producer_index_phys_addr_hi; /*14h */ + u32 consumer_index_phys_addr_lo; /*18h */ + u32 consumer_index_phys_addr_hi; /*1Ch */ + +} __attribute__ ((packed)); + +struct megasas_io_frame { + + u8 cmd; /*00h */ + u8 sense_len; /*01h */ + u8 cmd_status; /*02h */ + u8 scsi_status; /*03h */ + + u8 target_id; /*04h */ + u8 access_byte; /*05h */ + u8 reserved_0; /*06h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + u32 lba_count; /*14h */ + + u32 sense_buf_phys_addr_lo; /*18h */ + u32 sense_buf_phys_addr_hi; /*1Ch */ + + u32 start_lba_lo; /*20h */ + u32 start_lba_hi; /*24h */ + + union megasas_sgl sgl; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_pthru_frame { + + u8 cmd; /*00h */ + u8 sense_len; /*01h */ + u8 cmd_status; /*02h */ + u8 scsi_status; /*03h */ + + u8 target_id; /*04h */ + u8 lun; /*05h */ + u8 cdb_len; /*06h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + u32 data_xfer_len; /*14h */ + + u32 sense_buf_phys_addr_lo; /*18h */ + u32 sense_buf_phys_addr_hi; /*1Ch */ + + u8 cdb[16]; /*20h */ + union megasas_sgl sgl; /*30h */ + +} __attribute__ ((packed)); + +struct megasas_dcmd_frame { + + u8 cmd; /*00h */ + u8 reserved_0; /*01h */ + u8 cmd_status; /*02h */ + u8 reserved_1[4]; /*03h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + + u32 data_xfer_len; /*14h */ + u32 opcode; /*18h */ + + union { /*1Ch */ + u8 b[12]; + u16 s[6]; + u32 w[3]; + } mbox; + + union megasas_sgl sgl; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_abort_frame { + + u8 cmd; /*00h */ + u8 reserved_0; /*01h */ + u8 cmd_status; /*02h */ + + u8 reserved_1; /*03h */ + u32 reserved_2; /*04h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 reserved_3; /*12h */ + u32 reserved_4; /*14h */ + + u32 abort_context; /*18h */ + u32 pad_1; /*1Ch */ + + u32 abort_mfi_phys_addr_lo; /*20h */ + u32 abort_mfi_phys_addr_hi; /*24h */ + + u32 reserved_5[6]; /*28h */ + +} __attribute__ ((packed)); + +struct megasas_smp_frame { + + u8 cmd; /*00h */ + u8 reserved_1; /*01h */ + u8 cmd_status; /*02h */ + u8 connection_status; /*03h */ + + u8 reserved_2[3]; /*04h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + + u32 data_xfer_len; /*14h */ + u64 sas_addr; /*18h */ + + union { + struct megasas_sge32 sge32[2]; /* [0]: resp [1]: req */ + struct megasas_sge64 sge64[2]; /* [0]: resp [1]: req */ + } sgl; + +} __attribute__ ((packed)); + +struct megasas_stp_frame { + + u8 cmd; /*00h */ + u8 reserved_1; /*01h */ + u8 cmd_status; /*02h */ + u8 reserved_2; /*03h */ + + u8 target_id; /*04h */ + u8 reserved_3[2]; /*05h */ + u8 sge_count; /*07h */ + + u32 context; /*08h */ + u32 pad_0; /*0Ch */ + + u16 flags; /*10h */ + u16 timeout; /*12h */ + + u32 data_xfer_len; /*14h */ + + u16 fis[10]; /*18h */ + u32 stp_flags; + + union { + struct megasas_sge32 sge32[2]; /* [0]: resp [1]: data */ + struct megasas_sge64 sge64[2]; /* [0]: resp [1]: data */ + } sgl; + +} __attribute__ ((packed)); + +union megasas_frame { + + struct megasas_header hdr; + struct megasas_init_frame init; + struct megasas_io_frame io; + struct megasas_pthru_frame pthru; + struct megasas_dcmd_frame dcmd; + struct megasas_abort_frame abort; + struct megasas_smp_frame smp; + struct megasas_stp_frame stp; + + u8 raw_bytes[64]; +}; + +struct megasas_cmd; + +union megasas_evt_class_locale { + + struct { + u16 locale; + u8 reserved; + s8 class; + } __attribute__ ((packed)) members; + + u32 word; + +} __attribute__ ((packed)); + +struct megasas_evt_log_info { + u32 newest_seq_num; + u32 oldest_seq_num; + u32 clear_seq_num; + u32 shutdown_seq_num; + u32 boot_seq_num; + +} __attribute__ ((packed)); + +struct megasas_progress { + + u16 progress; + u16 elapsed_seconds; + +} __attribute__ ((packed)); + +struct megasas_evtarg_ld { + + u16 target_id; + u8 ld_index; + u8 reserved; + +} __attribute__ ((packed)); + +struct megasas_evtarg_pd { + u16 device_id; + u8 encl_index; + u8 slot_number; + +} __attribute__ ((packed)); + +struct megasas_evt_detail { + + u32 seq_num; + u32 time_stamp; + u32 code; + union megasas_evt_class_locale cl; + u8 arg_type; + u8 reserved1[15]; + + union { + struct { + struct megasas_evtarg_pd pd; + u8 cdb_length; + u8 sense_length; + u8 reserved[2]; + u8 cdb[16]; + u8 sense[64]; + } __attribute__ ((packed)) cdbSense; + + struct megasas_evtarg_ld ld; + + struct { + struct megasas_evtarg_ld ld; + u64 count; + } __attribute__ ((packed)) ld_count; + + struct { + u64 lba; + struct megasas_evtarg_ld ld; + } __attribute__ ((packed)) ld_lba; + + struct { + struct megasas_evtarg_ld ld; + u32 prevOwner; + u32 newOwner; + } __attribute__ ((packed)) ld_owner; + + struct { + u64 ld_lba; + u64 pd_lba; + struct megasas_evtarg_ld ld; + struct megasas_evtarg_pd pd; + } __attribute__ ((packed)) ld_lba_pd_lba; + + struct { + struct megasas_evtarg_ld ld; + struct megasas_progress prog; + } __attribute__ ((packed)) ld_prog; + + struct { + struct megasas_evtarg_ld ld; + u32 prev_state; + u32 new_state; + } __attribute__ ((packed)) ld_state; + + struct { + u64 strip; + struct megasas_evtarg_ld ld; + } __attribute__ ((packed)) ld_strip; + + struct megasas_evtarg_pd pd; + + struct { + struct megasas_evtarg_pd pd; + u32 err; + } __attribute__ ((packed)) pd_err; + + struct { + u64 lba; + struct megasas_evtarg_pd pd; + } __attribute__ ((packed)) pd_lba; + + struct { + u64 lba; + struct megasas_evtarg_pd pd; + struct megasas_evtarg_ld ld; + } __attribute__ ((packed)) pd_lba_ld; + + struct { + struct megasas_evtarg_pd pd; + struct megasas_progress prog; + } __attribute__ ((packed)) pd_prog; + + struct { + struct megasas_evtarg_pd pd; + u32 prevState; + u32 newState; + } __attribute__ ((packed)) pd_state; + + struct { + u16 vendorId; + u16 deviceId; + u16 subVendorId; + u16 subDeviceId; + } __attribute__ ((packed)) pci; + + u32 rate; + char str[96]; + + struct { + u32 rtc; + u32 elapsedSeconds; + } __attribute__ ((packed)) time; + + struct { + u32 ecar; + u32 elog; + char str[64]; + } __attribute__ ((packed)) ecc; + + u8 b[96]; + u16 s[48]; + u32 w[24]; + u64 d[12]; + } args; + + char description[128]; + +} __attribute__ ((packed)); + +struct megasas_instance { + + u32 *producer; + dma_addr_t producer_h; + u32 *consumer; + dma_addr_t consumer_h; + + u32 *reply_queue; + dma_addr_t reply_queue_h; + + unsigned long base_addr; + struct megasas_register_set __iomem *reg_set; + + s8 init_id; + u8 reserved[3]; + + u16 max_num_sge; + u16 max_fw_cmds; + u32 max_sectors_per_req; + + struct megasas_cmd **cmd_list; + struct list_head cmd_pool; + spinlock_t cmd_pool_lock; + struct dma_pool *frame_dma_pool; + struct dma_pool *sense_dma_pool; + + struct megasas_evt_detail *evt_detail; + dma_addr_t evt_detail_h; + struct megasas_cmd *aen_cmd; + struct semaphore aen_mutex; + struct semaphore ioctl_sem; + + struct Scsi_Host *host; + + wait_queue_head_t int_cmd_wait_q; + wait_queue_head_t abort_cmd_wait_q; + + struct pci_dev *pdev; + u32 unique_id; + + u32 fw_outstanding; + u32 hw_crit_error; + spinlock_t instance_lock; +}; + +#define MEGASAS_IS_LOGICAL(scp) \ + (scp->device->channel < MEGASAS_MAX_PD_CHANNELS) ? 0 : 1 + +#define MEGASAS_DEV_INDEX(inst, scp) \ + ((scp->device->channel % 2) * MEGASAS_MAX_DEV_PER_CHANNEL) + \ + scp->device->id + +struct megasas_cmd { + + union megasas_frame *frame; + dma_addr_t frame_phys_addr; + u8 *sense; + dma_addr_t sense_phys_addr; + + u32 index; + u8 sync_cmd; + u8 cmd_status; + u16 abort_aen; + + struct list_head list; + struct scsi_cmnd *scmd; + struct megasas_instance *instance; + u32 frame_count; +}; + +#define MAX_MGMT_ADAPTERS 1024 +#define MAX_IOCTL_SGE 16 + +struct megasas_iocpacket { + + u16 host_no; + u16 __pad1; + u32 sgl_off; + u32 sge_count; + u32 sense_off; + u32 sense_len; + union { + u8 raw[128]; + struct megasas_header hdr; + } frame; + + struct iovec sgl[MAX_IOCTL_SGE]; + +} __attribute__ ((packed)); + +struct megasas_aen { + u16 host_no; + u16 __pad1; + u32 seq_num; + u32 class_locale_word; +} __attribute__ ((packed)); + +#ifdef CONFIG_COMPAT +struct compat_megasas_iocpacket { + u16 host_no; + u16 __pad1; + u32 sgl_off; + u32 sge_count; + u32 sense_off; + u32 sense_len; + union { + u8 raw[128]; + struct megasas_header hdr; + } frame; + struct compat_iovec sgl[MAX_IOCTL_SGE]; +} __attribute__ ((packed)); + +#define MEGASAS_IOC_FIRMWARE _IOWR('M', 1, struct compat_megasas_iocpacket) +#else +#define MEGASAS_IOC_FIRMWARE _IOWR('M', 1, struct megasas_iocpacket) +#endif + +#define MEGASAS_IOC_GET_AEN _IOW('M', 3, struct megasas_aen) + +struct megasas_mgmt_info { + + u16 count; + struct megasas_instance *instance[MAX_MGMT_ADAPTERS]; + int max_index; +}; + +#endif /*LSI_MEGARAID_SAS_H */ diff --git a/drivers/scsi/qla2xxx/qla_rscn.c b/drivers/scsi/qla2xxx/qla_rscn.c index bdc3bc74bbe..1eba9882863 100644 --- a/drivers/scsi/qla2xxx/qla_rscn.c +++ b/drivers/scsi/qla2xxx/qla_rscn.c @@ -330,6 +330,8 @@ qla2x00_update_login_fcport(scsi_qla_host_t *ha, struct mbx_entry *mbxstat, fcport->flags &= ~FCF_FAILOVER_NEEDED; fcport->iodesc_idx_sent = IODESC_INVALID_INDEX; atomic_set(&fcport->state, FCS_ONLINE); + if (fcport->rport) + fc_remote_port_unblock(fcport->rport); } diff --git a/drivers/scsi/scsi_scan.c b/drivers/scsi/scsi_scan.c index fcf9f6cbb14..327c5d7e5bd 100644 --- a/drivers/scsi/scsi_scan.c +++ b/drivers/scsi/scsi_scan.c @@ -587,6 +587,7 @@ static int scsi_probe_lun(struct scsi_device *sdev, char *inq_result, if (sdev->scsi_level >= 2 || (sdev->scsi_level == 1 && (inq_result[3] & 0x0f) == 1)) sdev->scsi_level++; + sdev->sdev_target->scsi_level = sdev->scsi_level; return 0; } @@ -771,6 +772,15 @@ static int scsi_add_lun(struct scsi_device *sdev, char *inq_result, int *bflags) return SCSI_SCAN_LUN_PRESENT; } +static inline void scsi_destroy_sdev(struct scsi_device *sdev) +{ + if (sdev->host->hostt->slave_destroy) + sdev->host->hostt->slave_destroy(sdev); + transport_destroy_device(&sdev->sdev_gendev); + put_device(&sdev->sdev_gendev); +} + + /** * scsi_probe_and_add_lun - probe a LUN, if a LUN is found add it * @starget: pointer to target device structure @@ -803,9 +813,9 @@ static int scsi_probe_and_add_lun(struct scsi_target *starget, * The rescan flag is used as an optimization, the first scan of a * host adapter calls into here with rescan == 0. */ - if (rescan) { - sdev = scsi_device_lookup_by_target(starget, lun); - if (sdev) { + sdev = scsi_device_lookup_by_target(starget, lun); + if (sdev) { + if (rescan || sdev->sdev_state != SDEV_CREATED) { SCSI_LOG_SCAN_BUS(3, printk(KERN_INFO "scsi scan: device exists on %s\n", sdev->sdev_gendev.bus_id)); @@ -820,9 +830,9 @@ static int scsi_probe_and_add_lun(struct scsi_target *starget, sdev->model); return SCSI_SCAN_LUN_PRESENT; } - } - - sdev = scsi_alloc_sdev(starget, lun, hostdata); + scsi_device_put(sdev); + } else + sdev = scsi_alloc_sdev(starget, lun, hostdata); if (!sdev) goto out; @@ -877,12 +887,8 @@ static int scsi_probe_and_add_lun(struct scsi_target *starget, res = SCSI_SCAN_NO_RESPONSE; } } - } else { - if (sdev->host->hostt->slave_destroy) - sdev->host->hostt->slave_destroy(sdev); - transport_destroy_device(&sdev->sdev_gendev); - put_device(&sdev->sdev_gendev); - } + } else + scsi_destroy_sdev(sdev); out: return res; } @@ -1054,7 +1060,7 @@ EXPORT_SYMBOL(int_to_scsilun); * 0: scan completed (or no memory, so further scanning is futile) * 1: no report lun scan, or not configured **/ -static int scsi_report_lun_scan(struct scsi_device *sdev, int bflags, +static int scsi_report_lun_scan(struct scsi_target *starget, int bflags, int rescan) { char devname[64]; @@ -1067,7 +1073,8 @@ static int scsi_report_lun_scan(struct scsi_device *sdev, int bflags, struct scsi_lun *lunp, *lun_data; u8 *data; struct scsi_sense_hdr sshdr; - struct scsi_target *starget = scsi_target(sdev); + struct scsi_device *sdev; + struct Scsi_Host *shost = dev_to_shost(&starget->dev); /* * Only support SCSI-3 and up devices if BLIST_NOREPORTLUN is not set. @@ -1075,15 +1082,23 @@ static int scsi_report_lun_scan(struct scsi_device *sdev, int bflags, * support more than 8 LUNs. */ if ((bflags & BLIST_NOREPORTLUN) || - sdev->scsi_level < SCSI_2 || - (sdev->scsi_level < SCSI_3 && - (!(bflags & BLIST_REPORTLUN2) || sdev->host->max_lun <= 8)) ) + starget->scsi_level < SCSI_2 || + (starget->scsi_level < SCSI_3 && + (!(bflags & BLIST_REPORTLUN2) || shost->max_lun <= 8)) ) return 1; if (bflags & BLIST_NOLUN) return 0; + if (!(sdev = scsi_device_lookup_by_target(starget, 0))) { + sdev = scsi_alloc_sdev(starget, 0, NULL); + if (!sdev) + return 0; + if (scsi_device_get(sdev)) + return 0; + } + sprintf(devname, "host %d channel %d id %d", - sdev->host->host_no, sdev->channel, sdev->id); + shost->host_no, sdev->channel, sdev->id); /* * Allocate enough to hold the header (the same size as one scsi_lun) @@ -1098,8 +1113,10 @@ static int scsi_report_lun_scan(struct scsi_device *sdev, int bflags, length = (max_scsi_report_luns + 1) * sizeof(struct scsi_lun); lun_data = kmalloc(length, GFP_ATOMIC | (sdev->host->unchecked_isa_dma ? __GFP_DMA : 0)); - if (!lun_data) + if (!lun_data) { + printk(ALLOC_FAILURE_MSG, __FUNCTION__); goto out; + } scsi_cmd[0] = REPORT_LUNS; @@ -1201,10 +1218,6 @@ static int scsi_report_lun_scan(struct scsi_device *sdev, int bflags, for (i = 0; i < sizeof(struct scsi_lun); i++) printk("%02x", data[i]); printk(" has a LUN larger than currently supported.\n"); - } else if (lun == 0) { - /* - * LUN 0 has already been scanned. - */ } else if (lun > sdev->host->max_lun) { printk(KERN_WARNING "scsi: %s lun%d has a LUN larger" " than allowed by the host adapter\n", @@ -1227,13 +1240,13 @@ static int scsi_report_lun_scan(struct scsi_device *sdev, int bflags, } kfree(lun_data); - return 0; - out: - /* - * We are out of memory, don't try scanning any further. - */ - printk(ALLOC_FAILURE_MSG, __FUNCTION__); + scsi_device_put(sdev); + if (sdev->sdev_state == SDEV_CREATED) + /* + * the sdev we used didn't appear in the report luns scan + */ + scsi_destroy_sdev(sdev); return 0; } @@ -1299,7 +1312,6 @@ static void __scsi_scan_target(struct device *parent, unsigned int channel, struct Scsi_Host *shost = dev_to_shost(parent); int bflags = 0; int res; - struct scsi_device *sdev = NULL; struct scsi_target *starget; if (shost->this_id == id) @@ -1325,27 +1337,16 @@ static void __scsi_scan_target(struct device *parent, unsigned int channel, * Scan LUN 0, if there is some response, scan further. Ideally, we * would not configure LUN 0 until all LUNs are scanned. */ - res = scsi_probe_and_add_lun(starget, 0, &bflags, &sdev, rescan, NULL); - if (res == SCSI_SCAN_LUN_PRESENT) { - if (scsi_report_lun_scan(sdev, bflags, rescan) != 0) + res = scsi_probe_and_add_lun(starget, 0, &bflags, NULL, rescan, NULL); + if (res == SCSI_SCAN_LUN_PRESENT || res == SCSI_SCAN_TARGET_PRESENT) { + if (scsi_report_lun_scan(starget, bflags, rescan) != 0) /* * The REPORT LUN did not scan the target, * do a sequential scan. */ scsi_sequential_lun_scan(starget, bflags, - res, sdev->scsi_level, rescan); - } else if (res == SCSI_SCAN_TARGET_PRESENT) { - /* - * There's a target here, but lun 0 is offline so we - * can't use the report_lun scan. Fall back to a - * sequential lun scan with a bflags of SPARSELUN and - * a default scsi level of SCSI_2 - */ - scsi_sequential_lun_scan(starget, BLIST_SPARSELUN, - SCSI_SCAN_TARGET_PRESENT, SCSI_2, rescan); + res, starget->scsi_level, rescan); } - if (sdev) - scsi_device_put(sdev); out_reap: /* now determine if the target has any children at all @@ -1542,10 +1543,7 @@ void scsi_free_host_dev(struct scsi_device *sdev) { BUG_ON(sdev->id != sdev->host->this_id); - if (sdev->host->hostt->slave_destroy) - sdev->host->hostt->slave_destroy(sdev); - transport_destroy_device(&sdev->sdev_gendev); - put_device(&sdev->sdev_gendev); + scsi_destroy_sdev(sdev); } EXPORT_SYMBOL(scsi_free_host_dev); diff --git a/drivers/scsi/scsi_transport_sas.c b/drivers/scsi/scsi_transport_sas.c index ff724bbe661..1d145d2f9a3 100644 --- a/drivers/scsi/scsi_transport_sas.c +++ b/drivers/scsi/scsi_transport_sas.c @@ -628,17 +628,16 @@ sas_rphy_delete(struct sas_rphy *rphy) struct Scsi_Host *shost = dev_to_shost(parent->dev.parent); struct sas_host_attrs *sas_host = to_sas_host_attrs(shost); - transport_destroy_device(&rphy->dev); + scsi_remove_target(dev); - scsi_remove_target(&rphy->dev); + transport_remove_device(dev); + device_del(dev); + transport_destroy_device(dev); spin_lock(&sas_host->lock); list_del(&rphy->list); spin_unlock(&sas_host->lock); - transport_remove_device(dev); - device_del(dev); - transport_destroy_device(dev); put_device(&parent->dev); } EXPORT_SYMBOL(sas_rphy_delete); diff --git a/drivers/scsi/sg.c b/drivers/scsi/sg.c index 4d09a6e4dd2..ad94367df43 100644 --- a/drivers/scsi/sg.c +++ b/drivers/scsi/sg.c @@ -2849,8 +2849,7 @@ sg_proc_init(void) struct proc_dir_entry *pdep; struct sg_proc_leaf * leaf; - sg_proc_sgp = create_proc_entry(sg_proc_sg_dirname, - S_IFDIR | S_IRUGO | S_IXUGO, NULL); + sg_proc_sgp = proc_mkdir(sg_proc_sg_dirname, NULL); if (!sg_proc_sgp) return 1; for (k = 0; k < num_leaves; ++k) { |