diff options
Diffstat (limited to 'drivers/scsi')
| -rw-r--r-- | drivers/scsi/Kconfig | 8 | ||||
| -rw-r--r-- | drivers/scsi/Makefile | 1 | ||||
| -rw-r--r-- | drivers/scsi/sata_sil24.c | 786 |
3 files changed, 795 insertions, 0 deletions
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig index 96df148ed96..939d3442c13 100644 --- a/drivers/scsi/Kconfig +++ b/drivers/scsi/Kconfig @@ -499,6 +499,14 @@ config SCSI_SATA_SIL If unsure, say N. +config SCSI_SATA_SIL24 + tristate "Silicon Image 3124/3132 SATA support" + depends on SCSI_SATA && PCI && EXPERIMENTAL + help + This option enables support for Silicon Image 3124/3132 Serial ATA. + + If unsure, say N. + config SCSI_SATA_SIS tristate "SiS 964/180 SATA support" depends on SCSI_SATA && PCI && EXPERIMENTAL diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile index 3746fb9fa2f..64aaab64aeb 100644 --- a/drivers/scsi/Makefile +++ b/drivers/scsi/Makefile @@ -126,6 +126,7 @@ obj-$(CONFIG_SCSI_ATA_PIIX) += libata.o ata_piix.o obj-$(CONFIG_SCSI_SATA_PROMISE) += libata.o sata_promise.o obj-$(CONFIG_SCSI_SATA_QSTOR) += libata.o sata_qstor.o obj-$(CONFIG_SCSI_SATA_SIL) += libata.o sata_sil.o +obj-$(CONFIG_SCSI_SATA_SIL24) += libata.o sata_sil24.o obj-$(CONFIG_SCSI_SATA_VIA) += libata.o sata_via.o obj-$(CONFIG_SCSI_SATA_VITESSE) += libata.o sata_vsc.o obj-$(CONFIG_SCSI_SATA_SIS) += libata.o sata_sis.o diff --git a/drivers/scsi/sata_sil24.c b/drivers/scsi/sata_sil24.c new file mode 100644 index 00000000000..9958bc10a25 --- /dev/null +++ b/drivers/scsi/sata_sil24.c @@ -0,0 +1,786 @@ +/* + * sata_sil24.c - Driver for Silicon Image 3124/3132 SATA-2 controllers + * + * Copyright 2005 Tejun Heo + * + * Based on preview driver from Silicon Image. + * + * NOTE: No NCQ/ATAPI support yet. The preview driver didn't support + * NCQ nor ATAPI, and, unfortunately, I couldn't find out how to make + * those work. Enabling those shouldn't be difficult. Basic + * structure is all there (in libata-dev tree). If you have any + * information about this hardware, please contact me or linux-ide. + * Info is needed on... + * + * - How to issue tagged commands and turn on sactive on issue accordingly. + * - Where to put an ATAPI command and how to tell the device to send it. + * - How to enable/use 64bit. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2, or (at your option) any + * later version. + * + * This program is distributed in the hope that it will be useful, but + * WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU + * General Public License for more details. + * + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/blkdev.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/dma-mapping.h> +#include <scsi/scsi_host.h> +#include "scsi.h" +#include <linux/libata.h> +#include <asm/io.h> + +#define DRV_NAME "sata_sil24" +#define DRV_VERSION "0.20" /* Silicon Image's preview driver was 0.10 */ + +#define NR_PORTS 4 + +/* + * Port request block (PRB) 32 bytes + */ +struct sil24_prb { + u16 ctrl; + u16 prot; + u32 rx_cnt; + u8 fis[6 * 4]; +}; + +/* + * Scatter gather entry (SGE) 16 bytes + */ +struct sil24_sge { + u64 addr; + u32 cnt; + u32 flags; +}; + +/* + * Port multiplier + */ +struct sil24_port_multiplier { + u32 diag; + u32 sactive; +}; + +enum { + /* + * Global controller registers (128 bytes @ BAR0) + */ + /* 32 bit regs */ + HOST_SLOT_STAT = 0x00, /* 32 bit slot stat * 4 */ + HOST_CTRL = 0x40, + HOST_IRQ_STAT = 0x44, + HOST_PHY_CFG = 0x48, + HOST_BIST_CTRL = 0x50, + HOST_BIST_PTRN = 0x54, + HOST_BIST_STAT = 0x58, + HOST_MEM_BIST_STAT = 0x5c, + HOST_FLASH_CMD = 0x70, + /* 8 bit regs */ + HOST_FLASH_DATA = 0x74, + HOST_TRANSITION_DETECT = 0x75, + HOST_GPIO_CTRL = 0x76, + HOST_I2C_ADDR = 0x78, /* 32 bit */ + HOST_I2C_DATA = 0x7c, + HOST_I2C_XFER_CNT = 0x7e, + HOST_I2C_CTRL = 0x7f, + + /* HOST_SLOT_STAT bits */ + HOST_SSTAT_ATTN = (1 << 31), + + /* + * Port registers + * (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2) + */ + PORT_REGS_SIZE = 0x2000, + PORT_PRB = 0x0000, /* (32 bytes PRB + 16 bytes SGEs * 6) * 31 (3968 bytes) */ + /* TF is overlayed w/ PRB regs in the preview driver, + * but it doesn't seem to work. */ + PORT_TF = 0x0000, + + PORT_PM = 0x0f80, /* 8 bytes PM * 16 (128 bytes) */ + /* 32 bit regs */ + PORT_CTRL_STAT = 0x1000, /* write:ctrl, read:stat */ + PORT_CTRL_CLR = 0x1004, + PORT_IRQ_STAT = 0x1008, + PORT_IRQ_ENABLE_SET = 0x1010, + PORT_IRQ_ENABLE_CLR = 0x1014, + PORT_ACTIVATE_UPPER_ADDR= 0x101c, + PORT_EXEC_FIFO = 0x1020, + PORT_CMD_ERR = 0x1024, + PORT_FIS_CFG = 0x1028, + PORT_FIFO_THRES = 0x102c, + /* 16 bit regs */ + PORT_DECODE_ERR_CNT = 0x1040, + PORT_DECODE_ERR_THRESH = 0x1042, + PORT_CRC_ERR_CNT = 0x1044, + PORT_CRC_ERR_THRESH = 0x1046, + PORT_HSHK_ERR_CNT = 0x1048, + PORT_HSHK_ERR_THRESH = 0x104a, + /* 32 bit regs */ + PORT_PHY_CFG = 0x1050, + PORT_SLOT_STAT = 0x1800, + PORT_CMD_ACTIVATE = 0x1c00, /* 64 bit cmd activate * 31 (248 bytes) */ + PORT_EXEC_DIAG = 0x1e00, /* 32bit exec diag * 16 (64 bytes, 0-10 used on 3124) */ + PORT_PSD_DIAG = 0x1e40, /* 32bit psd diag * 16 (64 bytes, 0-8 used on 3124) */ + PORT_SCONTROL = 0x1f00, + PORT_SSTATUS = 0x1f04, + PORT_SERROR = 0x1f08, + PORT_SACTIVE = 0x1f0c, + + /* PORT_CTRL_STAT bits */ + PORT_CS_PORT_RST = (1 << 0), /* port reset */ + PORT_CS_DEV_RST = (1 << 1), /* device reset */ + PORT_CS_INIT = (1 << 2), /* port initialize */ + PORT_CS_IRQ_WOC = (1 << 3), /* interrupt write one to clear */ + PORT_CS_RESUME = (1 << 4), /* port resume */ + PORT_CS_32BIT_ACTV = (1 << 5), /* 32-bit activation */ + PORT_CS_PM_EN = (1 << 6), /* port multiplier enable */ + PORT_CS_RDY = (1 << 7), /* port ready to accept commands */ + + /* PORT_IRQ_STAT/ENABLE_SET/CLR */ + /* bits[11:0] are masked */ + PORT_IRQ_COMPLETE = (1 << 0), /* command(s) completed */ + PORT_IRQ_ERROR = (1 << 1), /* command execution error */ + PORT_IRQ_PORTRDY_CHG = (1 << 2), /* port ready change */ + PORT_IRQ_PWR_CHG = (1 << 3), /* power management change */ + PORT_IRQ_PHYRDY_CHG = (1 << 4), /* PHY ready change */ + PORT_IRQ_COMWAKE = (1 << 5), /* COMWAKE received */ + PORT_IRQ_UNK_FIS = (1 << 6), /* Unknown FIS received */ + PORT_IRQ_SDB_FIS = (1 << 11), /* SDB FIS received */ + + /* bits[27:16] are unmasked (raw) */ + PORT_IRQ_RAW_SHIFT = 16, + PORT_IRQ_MASKED_MASK = 0x7ff, + PORT_IRQ_RAW_MASK = (0x7ff << PORT_IRQ_RAW_SHIFT), + + /* ENABLE_SET/CLR specific, intr steering - 2 bit field */ + PORT_IRQ_STEER_SHIFT = 30, + PORT_IRQ_STEER_MASK = (3 << PORT_IRQ_STEER_SHIFT), + + /* PORT_CMD_ERR constants */ + PORT_CERR_DEV = 1, /* Error bit in D2H Register FIS */ + PORT_CERR_SDB = 2, /* Error bit in SDB FIS */ + PORT_CERR_DATA = 3, /* Error in data FIS not detected by dev */ + PORT_CERR_SEND = 4, /* Initial cmd FIS transmission failure */ + PORT_CERR_INCONSISTENT = 5, /* Protocol mismatch */ + PORT_CERR_DIRECTION = 6, /* Data direction mismatch */ + PORT_CERR_UNDERRUN = 7, /* Ran out of SGEs while writing */ + PORT_CERR_OVERRUN = 8, /* Ran out of SGEs while reading */ + PORT_CERR_PKT_PROT = 11, /* DIR invalid in 1st PIO setup of ATAPI */ + PORT_CERR_SGT_BOUNDARY = 16, /* PLD ecode 00 - SGT not on qword boundary */ + PORT_CERR_SGT_TGTABRT = 17, /* PLD ecode 01 - target abort */ + PORT_CERR_SGT_MSTABRT = 18, /* PLD ecode 10 - master abort */ + PORT_CERR_SGT_PCIPERR = 19, /* PLD ecode 11 - PCI parity err while fetching SGT */ + PORT_CERR_CMD_BOUNDARY = 24, /* ctrl[15:13] 001 - PRB not on qword boundary */ + PORT_CERR_CMD_TGTABRT = 25, /* ctrl[15:13] 010 - target abort */ + PORT_CERR_CMD_MSTABRT = 26, /* ctrl[15:13] 100 - master abort */ + PORT_CERR_CMD_PCIPERR = 27, /* ctrl[15:13] 110 - PCI parity err while fetching PRB */ + PORT_CERR_XFR_UNDEF = 32, /* PSD ecode 00 - undefined */ + PORT_CERR_XFR_TGTABRT = 33, /* PSD ecode 01 - target abort */ + PORT_CERR_XFR_MSGABRT = 34, /* PSD ecode 10 - master abort */ + PORT_CERR_XFR_PCIPERR = 35, /* PSD ecode 11 - PCI prity err during transfer */ + PORT_CERR_SENDSERVICE = 36, /* FIS received whiel sending service */ + + /* + * Other constants + */ + SGE_TRM = (1 << 31), /* Last SGE in chain */ + PRB_SOFT_RST = (1 << 7), /* Soft reset request (ign BSY?) */ + + /* board id */ + BID_SIL3124 = 0, + BID_SIL3132 = 1, + + IRQ_STAT_4PORTS = 0xf, +}; + +struct sil24_cmd_block { + struct sil24_prb prb; + struct sil24_sge sge[LIBATA_MAX_PRD]; +}; + +/* + * ap->private_data + * + * The preview driver always returned 0 for status. We emulate it + * here from the previous interrupt. + */ +struct sil24_port_priv { + void *port; + struct sil24_cmd_block *cmd_block; /* 32 cmd blocks */ + dma_addr_t cmd_block_dma; /* DMA base addr for them */ +}; + +/* ap->host_set->private_data */ +struct sil24_host_priv { + void *host_base; /* global controller control (128 bytes @BAR0) */ + void *port_base; /* port registers (4 * 8192 bytes @BAR2) */ +}; + +static u8 sil24_check_status(struct ata_port *ap); +static u8 sil24_check_err(struct ata_port *ap); +static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg); +static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val); +static void sil24_phy_reset(struct ata_port *ap); +static void sil24_qc_prep(struct ata_queued_cmd *qc); +static int sil24_qc_issue(struct ata_queued_cmd *qc); +static void sil24_irq_clear(struct ata_port *ap); +static void sil24_eng_timeout(struct ata_port *ap); +static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs); +static int sil24_port_start(struct ata_port *ap); +static void sil24_port_stop(struct ata_port *ap); +static void sil24_host_stop(struct ata_host_set *host_set); +static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent); + +static struct pci_device_id sil24_pci_tbl[] = { + { 0x1095, 0x3124, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3124 }, + { 0x1095, 0x3132, PCI_ANY_ID, PCI_ANY_ID, 0, 0, BID_SIL3132 }, +}; + +static struct pci_driver sil24_pci_driver = { + .name = DRV_NAME, + .id_table = sil24_pci_tbl, + .probe = sil24_init_one, + .remove = ata_pci_remove_one, /* safe? */ +}; + +static Scsi_Host_Template sil24_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .eh_strategy_handler = ata_scsi_error, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, + .ordered_flush = 1, /* NCQ not supported yet */ +}; + +static struct ata_port_operations sil24_ops = { + .port_disable = ata_port_disable, + + .check_status = sil24_check_status, + .check_altstatus = sil24_check_status, + .check_err = sil24_check_err, + .dev_select = ata_noop_dev_select, + + .phy_reset = sil24_phy_reset, + + .qc_prep = sil24_qc_prep, + .qc_issue = sil24_qc_issue, + + .eng_timeout = sil24_eng_timeout, + + .irq_handler = sil24_interrupt, + .irq_clear = sil24_irq_clear, + + .scr_read = sil24_scr_read, + .scr_write = sil24_scr_write, + + .port_start = sil24_port_start, + .port_stop = sil24_port_stop, + .host_stop = sil24_host_stop, +}; + +static struct ata_port_info sil24_port_info[] = { + /* sil_3124 */ + { + .sht = &sil24_sht, + .host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO | + ATA_FLAG_PIO_DMA, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil24_ops, + }, + /* sil_3132 */ + { + .sht = &sil24_sht, + .host_flags = ATA_FLAG_SATA | ATA_FLAG_NO_LEGACY | + ATA_FLAG_SATA_RESET | ATA_FLAG_MMIO | + ATA_FLAG_PIO_DMA, + .pio_mask = 0x1f, /* pio0-4 */ + .mwdma_mask = 0x07, /* mwdma0-2 */ + .udma_mask = 0x3f, /* udma0-5 */ + .port_ops = &sil24_ops, + }, +}; + +static u8 sil24_check_status(struct ata_port *ap) +{ + return ATA_DRDY; +} + +static u8 sil24_check_err(struct ata_port *ap) +{ + return 0; +} + +static int sil24_scr_map[] = { + [SCR_CONTROL] = 0, + [SCR_STATUS] = 1, + [SCR_ERROR] = 2, + [SCR_ACTIVE] = 3, +}; + +static u32 sil24_scr_read(struct ata_port *ap, unsigned sc_reg) +{ + void *scr_addr = (void *)ap->ioaddr.scr_addr; + if (sc_reg < ARRAY_SIZE(sil24_scr_map)) { + void *addr; + addr = scr_addr + sil24_scr_map[sc_reg] * 4; + return readl(scr_addr + sil24_scr_map[sc_reg] * 4); + } + return 0xffffffffU; +} + +static void sil24_scr_write(struct ata_port *ap, unsigned sc_reg, u32 val) +{ + void *scr_addr = (void *)ap->ioaddr.scr_addr; + if (sc_reg < ARRAY_SIZE(sil24_scr_map)) { + void *addr; + addr = scr_addr + sil24_scr_map[sc_reg] * 4; + writel(val, scr_addr + sil24_scr_map[sc_reg] * 4); + } +} + +static void sil24_phy_reset(struct ata_port *ap) +{ + __sata_phy_reset(ap); + /* + * No ATAPI yet. Just unconditionally indicate ATA device. + * If ATAPI device is attached, it will fail ATA_CMD_ID_ATA + * and libata core will ignore the device. + */ + if (!(ap->flags & ATA_FLAG_PORT_DISABLED)) + ap->device[0].class = ATA_DEV_ATA; +} + +static inline void sil24_fill_sg(struct ata_queued_cmd *qc, + struct sil24_cmd_block *cb) +{ + struct scatterlist *sg = qc->sg; + struct sil24_sge *sge = cb->sge; + unsigned i; + + for (i = 0; i < qc->n_elem; i++, sg++, sge++) { + sge->addr = cpu_to_le64(sg_dma_address(sg)); + sge->cnt = cpu_to_le32(sg_dma_len(sg)); + sge->flags = 0; + sge->flags = i < qc->n_elem - 1 ? 0 : cpu_to_le32(SGE_TRM); + } +} + +static void sil24_qc_prep(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct sil24_port_priv *pp = ap->private_data; + struct sil24_cmd_block *cb = pp->cmd_block + qc->tag; + struct sil24_prb *prb = &cb->prb; + + switch (qc->tf.protocol) { + case ATA_PROT_PIO: + case ATA_PROT_DMA: + case ATA_PROT_NODATA: + break; + default: + /* ATAPI isn't supported yet */ + BUG(); + } + + ata_tf_to_fis(&qc->tf, prb->fis, 0); + + if (qc->flags & ATA_QCFLAG_DMAMAP) + sil24_fill_sg(qc, cb); +} + +static int sil24_qc_issue(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct sil24_port_priv *pp = ap->private_data; + dma_addr_t paddr = pp->cmd_block_dma + qc->tag * sizeof(*pp->cmd_block); + + writel((u32)paddr, pp->port + PORT_CMD_ACTIVATE); + return 0; +} + +static void sil24_irq_clear(struct ata_port *ap) +{ + /* unused */ +} + +static void sil24_reset_controller(struct ata_port *ap) +{ + struct sil24_port_priv *pp = ap->private_data; + void *port = pp->port; + int cnt; + u32 tmp; + + printk(KERN_NOTICE DRV_NAME + " ata%u: resetting controller...\n", ap->id); + + /* Reset controller state. Is this correct? */ + writel(PORT_CS_DEV_RST, port + PORT_CTRL_STAT); + readl(port + PORT_CTRL_STAT); /* sync */ + + /* Max ~100ms */ + for (cnt = 0; cnt < 1000; cnt++) { + udelay(100); + tmp = readl(port + PORT_CTRL_STAT); + if (!(tmp & PORT_CS_DEV_RST)) + break; + } + if (tmp & PORT_CS_DEV_RST) + printk(KERN_ERR DRV_NAME + " ata%u: failed to reset controller\n", ap->id); +} + +static void sil24_eng_timeout(struct ata_port *ap) +{ + struct ata_queued_cmd *qc; + + qc = ata_qc_from_tag(ap, ap->active_tag); + if (!qc) { + printk(KERN_ERR "ata%u: BUG: tiemout without command\n", + ap->id); + return; + } + + /* + * hack alert! We cannot use the supplied completion + * function from inside the ->eh_strategy_handler() thread. + * libata is the only user of ->eh_strategy_handler() in + * any kernel, so the default scsi_done() assumes it is + * not being called from the SCSI EH. + */ + printk(KERN_ERR "ata%u: command timeout\n", ap->id); + qc->scsidone = scsi_finish_command; + ata_qc_complete(qc, ATA_ERR); + + sil24_reset_controller(ap); +} + +static inline void sil24_host_intr(struct ata_port *ap) +{ + struct ata_queued_cmd *qc = ata_qc_from_tag(ap, ap->active_tag); + struct sil24_port_priv *pp = ap->private_data; + void *port = pp->port; + u32 slot_stat; + + slot_stat = readl(port + PORT_SLOT_STAT); + if (!(slot_stat & HOST_SSTAT_ATTN)) { + if (qc) + ata_qc_complete(qc, 0); + } else { + u32 irq_stat, cmd_err, sstatus, serror; + + irq_stat = readl(port + PORT_IRQ_STAT); + cmd_err = readl(port + PORT_CMD_ERR); + sstatus = readl(port + PORT_SSTATUS); + serror = readl(port + PORT_SERROR); + + /* Clear IRQ/errors */ + writel(irq_stat, port + PORT_IRQ_STAT); + if (cmd_err) + writel(cmd_err, port + PORT_CMD_ERR); + if (serror) + writel(serror, port + PORT_SERROR); + + printk(KERN_ERR DRV_NAME " ata%u: error interrupt on port%d\n" + " stat=0x%x irq=0x%x cmd_err=%d sstatus=0x%x serror=0x%x\n", + ap->id, ap->port_no, slot_stat, irq_stat, cmd_err, sstatus, serror); + + if (qc) + ata_qc_complete(qc, ATA_ERR); + + sil24_reset_controller(ap); + } +} + +static irqreturn_t sil24_interrupt(int irq, void *dev_instance, struct pt_regs *regs) +{ + struct ata_host_set *host_set = dev_instance; + struct sil24_host_priv *hpriv = host_set->private_data; + unsigned handled = 0; + u32 status; + int i; + + status = readl(hpriv->host_base + HOST_IRQ_STAT); + + if (!(status & IRQ_STAT_4PORTS)) + goto out; + + spin_lock(&host_set->lock); + + for (i = 0; i < host_set->n_ports; i++) + if (status & (1 << i)) { + struct ata_port *ap = host_set->ports[i]; + if (ap && !(ap->flags & ATA_FLAG_PORT_DISABLED)) + sil24_host_intr(host_set->ports[i]); + else { + u32 tmp; + printk(KERN_WARNING DRV_NAME + ": spurious interrupt from port %d\n", i); + tmp = readl(hpriv->host_base + HOST_CTRL); + tmp &= ~(1 << i); + writel(tmp, hpriv->host_base + HOST_CTRL); + } + handled++; + } + + spin_unlock(&host_set->lock); + out: + return IRQ_RETVAL(handled); +} + +static int sil24_port_start(struct ata_port *ap) +{ + struct device *dev = ap->host_set->dev; + struct sil24_host_priv *hpriv = ap->host_set->private_data; + struct sil24_port_priv *pp; + struct sil24_cmd_block *cb; + size_t cb_size = sizeof(*cb); + dma_addr_t cb_dma; + + pp = kmalloc(sizeof(*pp), GFP_KERNEL); + if (!pp) + return -ENOMEM; + memset(pp, 0, sizeof(*pp)); + + cb = dma_alloc_coherent(dev, cb_size, &cb_dma, GFP_KERNEL); + if (!cb) { + kfree(pp); + return -ENOMEM; + } + memset(cb, 0, cb_size); + + pp->port = hpriv->port_base + ap->port_no * PORT_REGS_SIZE; + pp->cmd_block = cb; + pp->cmd_block_dma = cb_dma; + + ap->private_data = pp; + + return 0; +} + +static void sil24_port_stop(struct ata_port *ap) +{ + struct device *dev = ap->host_set->dev; + struct sil24_port_priv *pp = ap->private_data; + size_t cb_size = sizeof(*pp->cmd_block); + + dma_free_coherent(dev, cb_size, pp->cmd_block, pp->cmd_block_dma); + kfree(pp); +} + +static void sil24_host_stop(struct ata_host_set *host_set) +{ + struct sil24_host_priv *hpriv = host_set->private_data; + + iounmap(hpriv->host_base); + iounmap(hpriv->port_base); + kfree(hpriv); +} + +static int sil24_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +{ + static int printed_version = 0; + unsigned int board_id = (unsigned int)ent->driver_data; + struct ata_probe_ent *probe_ent = NULL; + struct sil24_host_priv *hpriv = NULL; + void *host_base = NULL, *port_base = NULL; + int i, rc; + + if (!printed_version++) + printk(KERN_DEBUG DRV_NAME " version " DRV_VERSION "\n"); + + rc = pci_enable_device(pdev); + if (rc) + return rc; + + rc = pci_request_regions(pdev, DRV_NAME); + if (rc) + goto out_disable; + + rc = -ENOMEM; + /* ioremap mmio registers */ + host_base = ioremap(pci_resource_start(pdev, 0), + pci_resource_len(pdev, 0)); + if (!host_base) + goto out_free; + port_base = ioremap(pci_resource_start(pdev, 2), + pci_resource_len(pdev, 2)); + if (!port_base) + goto out_free; + + /* allocate & init probe_ent and hpriv */ + probe_ent = kmalloc(sizeof(*probe_ent), GFP_KERNEL); + if (!probe_ent) + goto out_free; + + hpriv = kmalloc(sizeof(*hpriv), GFP_KERNEL); + if (!hpriv) + goto out_free; + + memset(probe_ent, 0, sizeof(*probe_ent)); + probe_ent->dev = pci_dev_to_dev(pdev); + INIT_LIST_HEAD(&probe_ent->node); + + probe_ent->sht = sil24_port_info[board_id].sht; + probe_ent->host_flags = sil24_port_info[board_id].host_flags; + probe_ent->pio_mask = sil24_port_info[board_id].pio_mask; + probe_ent->udma_mask = sil24_port_info[board_id].udma_mask; + probe_ent->port_ops = sil24_port_info[board_id].port_ops; + probe_ent->n_ports = (board_id == BID_SIL3124) ? 4 : 2; + + probe_ent->irq = pdev->irq; + probe_ent->irq_flags = SA_SHIRQ; + probe_ent->mmio_base = port_base; + probe_ent->private_data = hpriv; + + memset(hpriv, 0, sizeof(*hpriv)); + hpriv->host_base = host_base; + hpriv->port_base = port_base; + + /* + * Configure the device + */ + /* + * FIXME: This device is certainly 64-bit capable. We just + * don't know how to use it. After fixing 32bit activation in + * this function, enable 64bit masks here. + */ + rc = pci_set_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + printk(KERN_ERR DRV_NAME "(%s): 32-bit DMA enable failed\n", + pci_name(pdev)); + goto out_free; + } + rc = pci_set_consistent_dma_mask(pdev, DMA_32BIT_MASK); + if (rc) { + printk(KERN_ERR DRV_NAME "(%s): 32-bit consistent DMA enable failed\n", + pci_name(pdev)); + goto out_free; + } + + /* GPIO off */ + writel(0, host_base + HOST_FLASH_CMD); + + /* Mask interrupts during initialization */ + writel(0, host_base + HOST_CTRL); + + for (i = 0; i < probe_ent->n_ports; i++) { + void *port = port_base + i * PORT_REGS_SIZE; + unsigned long portu = (unsigned long)port; + u32 tmp; + int cnt; + + probe_ent->port[i].cmd_addr = portu + PORT_TF; + probe_ent->port[i].ctl_addr = portu + PORT_TF + 0xa; + probe_ent->port[i].altstatus_addr = portu + PORT_TF + 0xa; + probe_ent->port[i].scr_addr = portu + PORT_SCONTROL; + + ata_std_ports(&probe_ent->port[i]); + + /* Initial PHY setting */ + writel(0x20c, port + PORT_PHY_CFG); + + /* Clear port RST */ + tmp = readl(port + PORT_CTRL_STAT); + if (tmp & PORT_CS_PORT_RST) { + writel(PORT_CS_PORT_RST, port + PORT_CTRL_CLR); + readl(port + PORT_CTRL_STAT); /* sync */ + for (cnt = 0; cnt < 10; cnt++) { + msleep(10); + tmp = readl(port + PORT_CTRL_STAT); + if (!(tmp & PORT_CS_PORT_RST)) + break; + } + if (tmp & PORT_CS_PORT_RST) + printk(KERN_ERR DRV_NAME + "(%s): failed to clear port RST\n", + pci_name(pdev)); + } + + /* Zero error counters. */ + writel(0x8000, port + PORT_DECODE_ERR_THRESH); + writel(0x8000, port + PORT_CRC_ERR_THRESH); + writel(0x8000, port + PORT_HSHK_ERR_THRESH); + writel(0x0000, port + PORT_DECODE_ERR_CNT); + writel(0x0000, port + PORT_CRC_ERR_CNT); + writel(0x0000, port + PORT_HSHK_ERR_CNT); + + /* FIXME: 32bit activation? */ + writel(0, port + PORT_ACTIVATE_UPPER_ADDR); + writel(PORT_CS_32BIT_ACTV, port + PORT_CTRL_STAT); + + /* Configure interrupts */ + writel(0xffff, port + PORT_IRQ_ENABLE_CLR); + writel(PORT_IRQ_COMPLETE | PORT_IRQ_ERROR | PORT_IRQ_SDB_FIS, + port + PORT_IRQ_ENABLE_SET); + + /* Clear interrupts */ + writel(0x0fff0fff, port + PORT_IRQ_STAT); + writel(PORT_CS_IRQ_WOC, port + PORT_CTRL_CLR); + } + + /* Turn on interrupts */ + writel(IRQ_STAT_4PORTS, host_base + HOST_CTRL); + + pci_set_master(pdev); + + ata_device_add(probe_ent); + + kfree(probe_ent); + return 0; + + out_free: + if (host_base) + iounmap(host_base); + if (port_base) + iounmap(port_base); + kfree(probe_ent); + kfree(hpriv); + pci_release_regions(pdev); + out_disable: + pci_disable_device(pdev); + return rc; +} + +static int __init sil24_init(void) +{ + return pci_module_init(&sil24_pci_driver); +} + +static void __exit sil24_exit(void) +{ + pci_unregister_driver(&sil24_pci_driver); +} + +MODULE_AUTHOR("Tejun Heo"); +MODULE_DESCRIPTION("Silicon Image 3124/3132 SATA low-level driver"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, sil24_pci_tbl); + +module_init(sil24_init); +module_exit(sil24_exit); |