diff options
Diffstat (limited to 'drivers/scsi')
93 files changed, 4733 insertions, 17420 deletions
diff --git a/drivers/scsi/Kconfig b/drivers/scsi/Kconfig index fe25677a551..c8bd092fc94 100644 --- a/drivers/scsi/Kconfig +++ b/drivers/scsi/Kconfig @@ -204,9 +204,9 @@ config SCSI_MULTI_LUN Some devices support more than one LUN (Logical Unit Number) in order to allow access to several media, e.g. CD jukebox, USB card reader, mobile phone in mass storage mode. This option forces the kernel to - probe for all LUNs by default. This setting can be overriden by + probe for all LUNs by default. This setting can be overridden by max_luns boot/module parameter. Note that this option does not affect - devices conforming to SCSI-3 or higher as they can explicitely report + devices conforming to SCSI-3 or higher as they can explicitly report their number of LUNs. It is safe to say Y here unless you have one of those rare devices which reacts in an unexpected way when probed for multiple LUNs. @@ -499,47 +499,6 @@ config SCSI_AACRAID source "drivers/scsi/aic7xxx/Kconfig.aic7xxx" - -config SCSI_AIC7XXX_OLD - tristate "Adaptec AIC7xxx support (old driver)" - depends on (ISA || EISA || PCI ) && SCSI - help - WARNING This driver is an older aic7xxx driver and is no longer - under active development. Adaptec, Inc. is writing a new driver to - take the place of this one, and it is recommended that whenever - possible, people should use the new Adaptec written driver instead - of this one. This driver will eventually be phased out entirely. - - This is support for the various aic7xxx based Adaptec SCSI - controllers. These include the 274x EISA cards; 284x VLB cards; - 2902, 2910, 293x, 294x, 394x, 3985 and several other PCI and - motherboard based SCSI controllers from Adaptec. It does not support - the AAA-13x RAID controllers from Adaptec, nor will it likely ever - support them. It does not support the 2920 cards from Adaptec that - use the Future Domain SCSI controller chip. For those cards, you - need the "Future Domain 16xx SCSI support" driver. - - In general, if the controller is based on an Adaptec SCSI controller - chip from the aic777x series or the aic78xx series, this driver - should work. The only exception is the 7810 which is specifically - not supported (that's the RAID controller chip on the AAA-13x - cards). - - Note that the AHA2920 SCSI host adapter is *not* supported by this - driver; choose "Future Domain 16xx SCSI support" instead if you have - one of those. - - Information on the configuration options for this controller can be - found by checking the help file for each of the available - configuration options. You should read - <file:Documentation/scsi/aic7xxx_old.txt> at a minimum before - contacting the maintainer with any questions. The SCSI-HOWTO, - available from <http://www.tldp.org/docs.html#howto>, can also - be of great help. - - To compile this driver as a module, choose M here: the - module will be called aic7xxx_old. - source "drivers/scsi/aic7xxx/Kconfig.aic79xx" source "drivers/scsi/aic94xx/Kconfig" source "drivers/scsi/mvsas/Kconfig" diff --git a/drivers/scsi/Makefile b/drivers/scsi/Makefile index 149bb6bf184..e172d4f8e02 100644 --- a/drivers/scsi/Makefile +++ b/drivers/scsi/Makefile @@ -70,7 +70,6 @@ obj-$(CONFIG_SCSI_AHA1740) += aha1740.o obj-$(CONFIG_SCSI_AIC7XXX) += aic7xxx/ obj-$(CONFIG_SCSI_AIC79XX) += aic7xxx/ obj-$(CONFIG_SCSI_AACRAID) += aacraid/ -obj-$(CONFIG_SCSI_AIC7XXX_OLD) += aic7xxx_old.o obj-$(CONFIG_SCSI_AIC94XX) += aic94xx/ obj-$(CONFIG_SCSI_PM8001) += pm8001/ obj-$(CONFIG_SCSI_ISCI) += isci/ diff --git a/drivers/scsi/a2091.c b/drivers/scsi/a2091.c index 30fa38a0ad3..9176bfbd574 100644 --- a/drivers/scsi/a2091.c +++ b/drivers/scsi/a2091.c @@ -201,7 +201,7 @@ static int a2091_probe(struct zorro_dev *z, const struct zorro_device_id *ent) instance->irq = IRQ_AMIGA_PORTS; instance->unique_id = z->slotaddr; - regs = (struct a2091_scsiregs *)ZTWO_VADDR(z->resource.start); + regs = ZTWO_VADDR(z->resource.start); regs->DAWR = DAWR_A2091; wdregs.SASR = ®s->SASR; diff --git a/drivers/scsi/a3000.c b/drivers/scsi/a3000.c index c0f4f4290dd..dd5b64726dd 100644 --- a/drivers/scsi/a3000.c +++ b/drivers/scsi/a3000.c @@ -220,7 +220,7 @@ static int __init amiga_a3000_scsi_probe(struct platform_device *pdev) instance->irq = IRQ_AMIGA_PORTS; - regs = (struct a3000_scsiregs *)ZTWO_VADDR(res->start); + regs = ZTWO_VADDR(res->start); regs->DAWR = DAWR_A3000; wdregs.SASR = ®s->SASR; diff --git a/drivers/scsi/a4000t.c b/drivers/scsi/a4000t.c index 70c521f79f7..f5a2ab41543 100644 --- a/drivers/scsi/a4000t.c +++ b/drivers/scsi/a4000t.c @@ -56,7 +56,7 @@ static int __init amiga_a4000t_scsi_probe(struct platform_device *pdev) scsi_addr = res->start + A4000T_SCSI_OFFSET; /* Fill in the required pieces of hostdata */ - hostdata->base = (void __iomem *)ZTWO_VADDR(scsi_addr); + hostdata->base = ZTWO_VADDR(scsi_addr); hostdata->clock = 50; hostdata->chip710 = 1; hostdata->dmode_extra = DMODE_FC2; diff --git a/drivers/scsi/aic7xxx_old.c b/drivers/scsi/aic7xxx_old.c deleted file mode 100644 index 33ec9c64340..00000000000 --- a/drivers/scsi/aic7xxx_old.c +++ /dev/null @@ -1,11149 +0,0 @@ -/*+M************************************************************************* - * Adaptec AIC7xxx device driver for Linux. - * - * Copyright (c) 1994 John Aycock - * The University of Calgary Department of Computer Science. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2, or (at your option) - * any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; see the file COPYING. If not, write to - * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. - * - * Sources include the Adaptec 1740 driver (aha1740.c), the Ultrastor 24F - * driver (ultrastor.c), various Linux kernel source, the Adaptec EISA - * config file (!adp7771.cfg), the Adaptec AHA-2740A Series User's Guide, - * the Linux Kernel Hacker's Guide, Writing a SCSI Device Driver for Linux, - * the Adaptec 1542 driver (aha1542.c), the Adaptec EISA overlay file - * (adp7770.ovl), the Adaptec AHA-2740 Series Technical Reference Manual, - * the Adaptec AIC-7770 Data Book, the ANSI SCSI specification, the - * ANSI SCSI-2 specification (draft 10c), ... - * - * -------------------------------------------------------------------------- - * - * Modifications by Daniel M. Eischen (deischen@iworks.InterWorks.org): - * - * Substantially modified to include support for wide and twin bus - * adapters, DMAing of SCBs, tagged queueing, IRQ sharing, bug fixes, - * SCB paging, and other rework of the code. - * - * Parts of this driver were also based on the FreeBSD driver by - * Justin T. Gibbs. His copyright follows: - * - * -------------------------------------------------------------------------- - * Copyright (c) 1994-1997 Justin Gibbs. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions, and the following disclaimer, - * without modification, immediately at the beginning of the file. - * 2. Redistributions in binary form must reproduce the above copyright - * notice, this list of conditions and the following disclaimer in the - * documentation and/or other materials provided with the distribution. - * 3. The name of the author may not be used to endorse or promote products - * derived from this software without specific prior written permission. - * - * Where this Software is combined with software released under the terms of - * the GNU General Public License ("GPL") and the terms of the GPL would require the - * combined work to also be released under the terms of the GPL, the terms - * and conditions of this License will apply in addition to those of the - * GPL with the exception of any terms or conditions of this License that - * conflict with, or are expressly prohibited by, the GPL. - * - * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND - * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR - * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS - * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) - * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT - * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY - * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF - * SUCH DAMAGE. - * - * $Id: aic7xxx.c,v 1.119 1997/06/27 19:39:18 gibbs Exp $ - *--------------------------------------------------------------------------- - * - * Thanks also go to (in alphabetical order) the following: - * - * Rory Bolt - Sequencer bug fixes - * Jay Estabrook - Initial DEC Alpha support - * Doug Ledford - Much needed abort/reset bug fixes - * Kai Makisara - DMAing of SCBs - * - * A Boot time option was also added for not resetting the scsi bus. - * - * Form: aic7xxx=extended - * aic7xxx=no_reset - * aic7xxx=ultra - * aic7xxx=irq_trigger:[0,1] # 0 edge, 1 level - * aic7xxx=verbose - * - * Daniel M. Eischen, deischen@iworks.InterWorks.org, 1/23/97 - * - * $Id: aic7xxx.c,v 4.1 1997/06/12 08:23:42 deang Exp $ - *-M*************************************************************************/ - -/*+M************************************************************************** - * - * Further driver modifications made by Doug Ledford <dledford@redhat.com> - * - * Copyright (c) 1997-1999 Doug Ledford - * - * These changes are released under the same licensing terms as the FreeBSD - * driver written by Justin Gibbs. Please see his Copyright notice above - * for the exact terms and conditions covering my changes as well as the - * warranty statement. - * - * Modifications made to the aic7xxx.c,v 4.1 driver from Dan Eischen include - * but are not limited to: - * - * 1: Import of the latest FreeBSD sequencer code for this driver - * 2: Modification of kernel code to accommodate different sequencer semantics - * 3: Extensive changes throughout kernel portion of driver to improve - * abort/reset processing and error hanndling - * 4: Other work contributed by various people on the Internet - * 5: Changes to printk information and verbosity selection code - * 6: General reliability related changes, especially in IRQ management - * 7: Modifications to the default probe/attach order for supported cards - * 8: SMP friendliness has been improved - * - * Overall, this driver represents a significant departure from the official - * aic7xxx driver released by Dan Eischen in two ways. First, in the code - * itself. A diff between the two version of the driver is now a several - * thousand line diff. Second, in approach to solving the same problem. The - * problem is importing the FreeBSD aic7xxx driver code to linux can be a - * difficult and time consuming process, that also can be error prone. Dan - * Eischen's official driver uses the approach that the linux and FreeBSD - * drivers should be as identical as possible. To that end, his next version - * of this driver will be using a mid-layer code library that he is developing - * to moderate communications between the linux mid-level SCSI code and the - * low level FreeBSD driver. He intends to be able to essentially drop the - * FreeBSD driver into the linux kernel with only a few minor tweaks to some - * include files and the like and get things working, making for fast easy - * imports of the FreeBSD code into linux. - * - * I disagree with Dan's approach. Not that I don't think his way of doing - * things would be nice, easy to maintain, and create a more uniform driver - * between FreeBSD and Linux. I have no objection to those issues. My - * disagreement is on the needed functionality. There simply are certain - * things that are done differently in FreeBSD than linux that will cause - * problems for this driver regardless of any middle ware Dan implements. - * The biggest example of this at the moment is interrupt semantics. Linux - * doesn't provide the same protection techniques as FreeBSD does, nor can - * they be easily implemented in any middle ware code since they would truly - * belong in the kernel proper and would effect all drivers. For the time - * being, I see issues such as these as major stumbling blocks to the - * reliability of code based upon such middle ware. Therefore, I choose to - * use a different approach to importing the FreeBSD code that doesn't - * involve any middle ware type code. My approach is to import the sequencer - * code from FreeBSD wholesale. Then, to only make changes in the kernel - * portion of the driver as they are needed for the new sequencer semantics. - * In this way, the portion of the driver that speaks to the rest of the - * linux kernel is fairly static and can be changed/modified to solve - * any problems one might encounter without concern for the FreeBSD driver. - * - * Note: If time and experience should prove me wrong that the middle ware - * code Dan writes is reliable in its operation, then I'll retract my above - * statements. But, for those that don't know, I'm from Missouri (in the US) - * and our state motto is "The Show-Me State". Well, before I will put - * faith into it, you'll have to show me that it works :) - * - *_M*************************************************************************/ - -/* - * The next three defines are user configurable. These should be the only - * defines a user might need to get in here and change. There are other - * defines buried deeper in the code, but those really shouldn't need touched - * under normal conditions. - */ - -/* - * AIC7XXX_STRICT_PCI_SETUP - * Should we assume the PCI config options on our controllers are set with - * sane and proper values, or should we be anal about our PCI config - * registers and force them to what we want? The main advantage to - * defining this option is on non-Intel hardware where the BIOS may not - * have been run to set things up, or if you have one of the BIOSless - * Adaptec controllers, such as a 2910, that don't get set up by the - * BIOS. However, keep in mind that we really do set the most important - * items in the driver regardless of this setting, this only controls some - * of the more esoteric PCI options on these cards. In that sense, I - * would default to leaving this off. However, if people wish to try - * things both ways, that would also help me to know if there are some - * machines where it works one way but not another. - * - * -- July 7, 17:09 - * OK...I need this on my machine for testing, so the default is to - * leave it defined. - * - * -- July 7, 18:49 - * I needed it for testing, but it didn't make any difference, so back - * off she goes. - * - * -- July 16, 23:04 - * I turned it back on to try and compensate for the 2.1.x PCI code - * which no longer relies solely on the BIOS and now tries to set - * things itself. - */ - -#define AIC7XXX_STRICT_PCI_SETUP - -/* - * AIC7XXX_VERBOSE_DEBUGGING - * This option enables a lot of extra printk();s in the code, surrounded - * by if (aic7xxx_verbose ...) statements. Executing all of those if - * statements and the extra checks can get to where it actually does have - * an impact on CPU usage and such, as well as code size. Disabling this - * define will keep some of those from becoming part of the code. - * - * NOTE: Currently, this option has no real effect, I will be adding the - * various #ifdef's in the code later when I've decided a section is - * complete and no longer needs debugging. OK...a lot of things are now - * surrounded by this define, so turning this off does have an impact. - */ - -/* - * #define AIC7XXX_VERBOSE_DEBUGGING - */ - -#include <linux/module.h> -#include <stdarg.h> -#include <asm/io.h> -#include <asm/irq.h> -#include <asm/byteorder.h> -#include <linux/string.h> -#include <linux/errno.h> -#include <linux/kernel.h> -#include <linux/ioport.h> -#include <linux/delay.h> -#include <linux/pci.h> -#include <linux/proc_fs.h> -#include <linux/blkdev.h> -#include <linux/init.h> -#include <linux/spinlock.h> -#include <linux/smp.h> -#include <linux/interrupt.h> -#include "scsi.h" -#include <scsi/scsi_host.h> -#include "aic7xxx_old/aic7xxx.h" - -#include "aic7xxx_old/sequencer.h" -#include "aic7xxx_old/scsi_message.h" -#include "aic7xxx_old/aic7xxx_reg.h" -#include <scsi/scsicam.h> - -#include <linux/stat.h> -#include <linux/slab.h> /* for kmalloc() */ - -#define AIC7XXX_C_VERSION "5.2.6" - -#define ALL_TARGETS -1 -#define ALL_CHANNELS -1 -#define ALL_LUNS -1 -#define MAX_TARGETS 16 -#define MAX_LUNS 8 -#ifndef TRUE -# define TRUE 1 -#endif -#ifndef FALSE -# define FALSE 0 -#endif - -#if defined(__powerpc__) || defined(__i386__) || defined(__x86_64__) -# define MMAPIO -#endif - -/* - * You can try raising me for better performance or lowering me if you have - * flaky devices that go off the scsi bus when hit with too many tagged - * commands (like some IBM SCSI-3 LVD drives). - */ -#define AIC7XXX_CMDS_PER_DEVICE 32 - -typedef struct -{ - unsigned char tag_commands[16]; /* Allow for wide/twin adapters. */ -} adapter_tag_info_t; - -/* - * Make a define that will tell the driver not to the default tag depth - * everywhere. - */ -#define DEFAULT_TAG_COMMANDS {0, 0, 0, 0, 0, 0, 0, 0,\ - 0, 0, 0, 0, 0, 0, 0, 0} - -/* - * Modify this as you see fit for your system. By setting tag_commands - * to 0, the driver will use it's own algorithm for determining the - * number of commands to use (see above). When 255, the driver will - * not enable tagged queueing for that particular device. When positive - * (> 0) and (< 255) the values in the array are used for the queue_depth. - * Note that the maximum value for an entry is 254, but you're insane if - * you try to use that many commands on one device. - * - * In this example, the first line will disable tagged queueing for all - * the devices on the first probed aic7xxx adapter. - * - * The second line enables tagged queueing with 4 commands/LUN for IDs - * (1, 2-11, 13-15), disables tagged queueing for ID 12, and tells the - * driver to use its own algorithm for ID 1. - * - * The third line is the same as the first line. - * - * The fourth line disables tagged queueing for devices 0 and 3. It - * enables tagged queueing for the other IDs, with 16 commands/LUN - * for IDs 1 and 4, 127 commands/LUN for ID 8, and 4 commands/LUN for - * IDs 2, 5-7, and 9-15. - */ - -/* - * NOTE: The below structure is for reference only, the actual structure - * to modify in order to change things is found after this fake one. - * -adapter_tag_info_t aic7xxx_tag_info[] = -{ - {DEFAULT_TAG_COMMANDS}, - {{4, 0, 4, 4, 4, 4, 4, 4, 4, 4, 4, 4, 255, 4, 4, 4}}, - {DEFAULT_TAG_COMMANDS}, - {{255, 16, 4, 255, 16, 4, 4, 4, 127, 4, 4, 4, 4, 4, 4, 4}} -}; -*/ - -static adapter_tag_info_t aic7xxx_tag_info[] = -{ - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS}, - {DEFAULT_TAG_COMMANDS} -}; - - -/* - * Define an array of board names that can be indexed by aha_type. - * Don't forget to change this when changing the types! - */ -static const char *board_names[] = { - "AIC-7xxx Unknown", /* AIC_NONE */ - "Adaptec AIC-7810 Hardware RAID Controller", /* AIC_7810 */ - "Adaptec AIC-7770 SCSI host adapter", /* AIC_7770 */ - "Adaptec AHA-274X SCSI host adapter", /* AIC_7771 */ - "Adaptec AHA-284X SCSI host adapter", /* AIC_284x */ - "Adaptec AIC-7850 SCSI host adapter", /* AIC_7850 */ - "Adaptec AIC-7855 SCSI host adapter", /* AIC_7855 */ - "Adaptec AIC-7860 Ultra SCSI host adapter", /* AIC_7860 */ - "Adaptec AHA-2940A Ultra SCSI host adapter", /* AIC_7861 */ - "Adaptec AIC-7870 SCSI host adapter", /* AIC_7870 */ - "Adaptec AHA-294X SCSI host adapter", /* AIC_7871 */ - "Adaptec AHA-394X SCSI host adapter", /* AIC_7872 */ - "Adaptec AHA-398X SCSI host adapter", /* AIC_7873 */ - "Adaptec AHA-2944 SCSI host adapter", /* AIC_7874 */ - "Adaptec AIC-7880 Ultra SCSI host adapter", /* AIC_7880 */ - "Adaptec AHA-294X Ultra SCSI host adapter", /* AIC_7881 */ - "Adaptec AHA-394X Ultra SCSI host adapter", /* AIC_7882 */ - "Adaptec AHA-398X Ultra SCSI host adapter", /* AIC_7883 */ - "Adaptec AHA-2944 Ultra SCSI host adapter", /* AIC_7884 */ - "Adaptec AHA-2940UW Pro Ultra SCSI host adapter", /* AIC_7887 */ - "Adaptec AIC-7895 Ultra SCSI host adapter", /* AIC_7895 */ - "Adaptec AIC-7890/1 Ultra2 SCSI host adapter", /* AIC_7890 */ - "Adaptec AHA-293X Ultra2 SCSI host adapter", /* AIC_7890 */ - "Adaptec AHA-294X Ultra2 SCSI host adapter", /* AIC_7890 */ - "Adaptec AIC-7896/7 Ultra2 SCSI host adapter", /* AIC_7896 */ - "Adaptec AHA-394X Ultra2 SCSI host adapter", /* AIC_7897 */ - "Adaptec AHA-395X Ultra2 SCSI host adapter", /* AIC_7897 */ - "Adaptec PCMCIA SCSI controller", /* card bus stuff */ - "Adaptec AIC-7892 Ultra 160/m SCSI host adapter", /* AIC_7892 */ - "Adaptec AIC-7899 Ultra 160/m SCSI host adapter", /* AIC_7899 */ -}; - -/* - * There should be a specific return value for this in scsi.h, but - * it seems that most drivers ignore it. - */ -#define DID_UNDERFLOW DID_ERROR - -/* - * What we want to do is have the higher level scsi driver requeue - * the command to us. There is no specific driver status for this - * condition, but the higher level scsi driver will requeue the - * command on a DID_BUS_BUSY error. - * - * Upon further inspection and testing, it seems that DID_BUS_BUSY - * will *always* retry the command. We can get into an infinite loop - * if this happens when we really want some sort of counter that - * will automatically abort/reset the command after so many retries. - * Using DID_ERROR will do just that. (Made by a suggestion by - * Doug Ledford 8/1/96) - */ -#define DID_RETRY_COMMAND DID_ERROR - -#define HSCSIID 0x07 -#define SCSI_RESET 0x040 - -/* - * EISA/VL-bus stuff - */ -#define MINSLOT 1 -#define MAXSLOT 15 -#define SLOTBASE(x) ((x) << 12) -#define BASE_TO_SLOT(x) ((x) >> 12) - -/* - * Standard EISA Host ID regs (Offset from slot base) - */ -#define AHC_HID0 0x80 /* 0,1: msb of ID2, 2-7: ID1 */ -#define AHC_HID1 0x81 /* 0-4: ID3, 5-7: LSB ID2 */ -#define AHC_HID2 0x82 /* product */ -#define AHC_HID3 0x83 /* firmware revision */ - -/* - * AIC-7770 I/O range to reserve for a card - */ -#define MINREG 0xC00 -#define MAXREG 0xCFF - -#define INTDEF 0x5C /* Interrupt Definition Register */ - -/* - * AIC-78X0 PCI registers - */ -#define CLASS_PROGIF_REVID 0x08 -#define DEVREVID 0x000000FFul -#define PROGINFC 0x0000FF00ul -#define SUBCLASS 0x00FF0000ul -#define BASECLASS 0xFF000000ul - -#define CSIZE_LATTIME 0x0C -#define CACHESIZE 0x0000003Ful /* only 5 bits */ -#define LATTIME 0x0000FF00ul - -#define DEVCONFIG 0x40 -#define SCBSIZE32 0x00010000ul /* aic789X only */ -#define MPORTMODE 0x00000400ul /* aic7870 only */ -#define RAMPSM 0x00000200ul /* aic7870 only */ -#define RAMPSM_ULTRA2 0x00000004 -#define VOLSENSE 0x00000100ul -#define SCBRAMSEL 0x00000080ul -#define SCBRAMSEL_ULTRA2 0x00000008 -#define MRDCEN 0x00000040ul -#define EXTSCBTIME 0x00000020ul /* aic7870 only */ -#define EXTSCBPEN 0x00000010ul /* aic7870 only */ -#define BERREN 0x00000008ul -#define DACEN 0x00000004ul -#define STPWLEVEL 0x00000002ul -#define DIFACTNEGEN 0x00000001ul /* aic7870 only */ - -#define SCAMCTL 0x1a /* Ultra2 only */ -#define CCSCBBADDR 0xf0 /* aic7895/6/7 */ - -/* - * Define the different types of SEEPROMs on aic7xxx adapters - * and make it also represent the address size used in accessing - * its registers. The 93C46 chips have 1024 bits organized into - * 64 16-bit words, while the 93C56 chips have 2048 bits organized - * into 128 16-bit words. The C46 chips use 6 bits to address - * each word, while the C56 and C66 (4096 bits) use 8 bits to - * address each word. - */ -typedef enum {C46 = 6, C56_66 = 8} seeprom_chip_type; - -/* - * - * Define the format of the SEEPROM registers (16 bits). - * - */ -struct seeprom_config { - -/* - * SCSI ID Configuration Flags - */ -#define CFXFER 0x0007 /* synchronous transfer rate */ -#define CFSYNCH 0x0008 /* enable synchronous transfer */ -#define CFDISC 0x0010 /* enable disconnection */ -#define CFWIDEB 0x0020 /* wide bus device (wide card) */ -#define CFSYNCHISULTRA 0x0040 /* CFSYNC is an ultra offset */ -#define CFNEWULTRAFORMAT 0x0080 /* Use the Ultra2 SEEPROM format */ -#define CFSTART 0x0100 /* send start unit SCSI command */ -#define CFINCBIOS 0x0200 /* include in BIOS scan */ -#define CFRNFOUND 0x0400 /* report even if not found */ -#define CFMULTILUN 0x0800 /* probe mult luns in BIOS scan */ -#define CFWBCACHEYES 0x4000 /* Enable W-Behind Cache on drive */ -#define CFWBCACHENC 0xc000 /* Don't change W-Behind Cache */ -/* UNUSED 0x3000 */ - unsigned short device_flags[16]; /* words 0-15 */ - -/* - * BIOS Control Bits - */ -#define CFSUPREM 0x0001 /* support all removable drives */ -#define CFSUPREMB 0x0002 /* support removable drives for boot only */ -#define CFBIOSEN 0x0004 /* BIOS enabled */ -/* UNUSED 0x0008 */ -#define CFSM2DRV 0x0010 /* support more than two drives */ -#define CF284XEXTEND 0x0020 /* extended translation (284x cards) */ -/* UNUSED 0x0040 */ -#define CFEXTEND 0x0080 /* extended translation enabled */ -/* UNUSED 0xFF00 */ - unsigned short bios_control; /* word 16 */ - -/* - * Host Adapter Control Bits - */ -#define CFAUTOTERM 0x0001 /* Perform Auto termination */ -#define CFULTRAEN 0x0002 /* Ultra SCSI speed enable (Ultra cards) */ -#define CF284XSELTO 0x0003 /* Selection timeout (284x cards) */ -#define CF284XFIFO 0x000C /* FIFO Threshold (284x cards) */ -#define CFSTERM 0x0004 /* SCSI low byte termination */ -#define CFWSTERM 0x0008 /* SCSI high byte termination (wide card) */ -#define CFSPARITY 0x0010 /* SCSI parity */ -#define CF284XSTERM 0x0020 /* SCSI low byte termination (284x cards) */ -#define CFRESETB 0x0040 /* reset SCSI bus at boot */ -#define CFBPRIMARY 0x0100 /* Channel B primary on 7895 chipsets */ -#define CFSEAUTOTERM 0x0400 /* aic7890 Perform SE Auto Term */ -#define CFLVDSTERM 0x0800 /* aic7890 LVD Termination */ -/* UNUSED 0xF280 */ - unsigned short adapter_control; /* word 17 */ - -/* - * Bus Release, Host Adapter ID - */ -#define CFSCSIID 0x000F /* host adapter SCSI ID */ -/* UNUSED 0x00F0 */ -#define CFBRTIME 0xFF00 /* bus release time */ - unsigned short brtime_id; /* word 18 */ - -/* - * Maximum targets - */ -#define CFMAXTARG 0x00FF /* maximum targets */ -/* UNUSED 0xFF00 */ - unsigned short max_targets; /* word 19 */ - - unsigned short res_1[11]; /* words 20-30 */ - unsigned short checksum; /* word 31 */ -}; - -#define SELBUS_MASK 0x0a -#define SELNARROW 0x00 -#define SELBUSB 0x08 -#define SINGLE_BUS 0x00 - -#define SCB_TARGET(scb) \ - (((scb)->hscb->target_channel_lun & TID) >> 4) -#define SCB_LUN(scb) \ - ((scb)->hscb->target_channel_lun & LID) -#define SCB_IS_SCSIBUS_B(scb) \ - (((scb)->hscb->target_channel_lun & SELBUSB) != 0) - -/* - * If an error occurs during a data transfer phase, run the command - * to completion - it's easier that way - making a note of the error - * condition in this location. This then will modify a DID_OK status - * into an appropriate error for the higher-level SCSI code. - */ -#define aic7xxx_error(cmd) ((cmd)->SCp.Status) - -/* - * Keep track of the targets returned status. - */ -#define aic7xxx_status(cmd) ((cmd)->SCp.sent_command) - -/* - * The position of the SCSI commands scb within the scb array. - */ -#define aic7xxx_position(cmd) ((cmd)->SCp.have_data_in) - -/* - * The stored DMA mapping for single-buffer data transfers. - */ -#define aic7xxx_mapping(cmd) ((cmd)->SCp.phase) - -/* - * Get out private data area from a scsi cmd pointer - */ -#define AIC_DEV(cmd) ((struct aic_dev_data *)(cmd)->device->hostdata) - -/* - * So we can keep track of our host structs - */ -static struct aic7xxx_host *first_aic7xxx = NULL; - -/* - * As of Linux 2.1, the mid-level SCSI code uses virtual addresses - * in the scatter-gather lists. We need to convert the virtual - * addresses to physical addresses. - */ -struct hw_scatterlist { - unsigned int address; - unsigned int length; -}; - -/* - * Maximum number of SG segments these cards can support. - */ -#define AIC7XXX_MAX_SG 128 - -/* - * The maximum number of SCBs we could have for ANY type - * of card. DON'T FORGET TO CHANGE THE SCB MASK IN THE - * SEQUENCER CODE IF THIS IS MODIFIED! - */ -#define AIC7XXX_MAXSCB 255 - - -struct aic7xxx_hwscb { -/* ------------ Begin hardware supported fields ---------------- */ -/* 0*/ unsigned char control; -/* 1*/ unsigned char target_channel_lun; /* 4/1/3 bits */ -/* 2*/ unsigned char target_status; -/* 3*/ unsigned char SG_segment_count; -/* 4*/ unsigned int SG_list_pointer; -/* 8*/ unsigned char residual_SG_segment_count; -/* 9*/ unsigned char residual_data_count[3]; -/*12*/ unsigned int data_pointer; -/*16*/ unsigned int data_count; -/*20*/ unsigned int SCSI_cmd_pointer; -/*24*/ unsigned char SCSI_cmd_length; -/*25*/ unsigned char tag; /* Index into our kernel SCB array. - * Also used as the tag for tagged I/O - */ -#define SCB_PIO_TRANSFER_SIZE 26 /* amount we need to upload/download - * via PIO to initialize a transaction. - */ -/*26*/ unsigned char next; /* Used to thread SCBs awaiting selection - * or disconnected down in the sequencer. - */ -/*27*/ unsigned char prev; -/*28*/ unsigned int pad; /* - * Unused by the kernel, but we require - * the padding so that the array of - * hardware SCBs is aligned on 32 byte - * boundaries so the sequencer can index - */ -}; - -typedef enum { - SCB_FREE = 0x0000, - SCB_DTR_SCB = 0x0001, - SCB_WAITINGQ = 0x0002, - SCB_ACTIVE = 0x0004, - SCB_SENSE = 0x0008, - SCB_ABORT = 0x0010, - SCB_DEVICE_RESET = 0x0020, - SCB_RESET = 0x0040, - SCB_RECOVERY_SCB = 0x0080, - SCB_MSGOUT_PPR = 0x0100, - SCB_MSGOUT_SENT = 0x0200, - SCB_MSGOUT_SDTR = 0x0400, - SCB_MSGOUT_WDTR = 0x0800, - SCB_MSGOUT_BITS = SCB_MSGOUT_PPR | - SCB_MSGOUT_SENT | - SCB_MSGOUT_SDTR | - SCB_MSGOUT_WDTR, - SCB_QUEUED_ABORT = 0x1000, - SCB_QUEUED_FOR_DONE = 0x2000, - SCB_WAS_BUSY = 0x4000, - SCB_QUEUE_FULL = 0x8000 -} scb_flag_type; - -typedef enum { - AHC_FNONE = 0x00000000, - AHC_PAGESCBS = 0x00000001, - AHC_CHANNEL_B_PRIMARY = 0x00000002, - AHC_USEDEFAULTS = 0x00000004, - AHC_INDIRECT_PAGING = 0x00000008, - AHC_CHNLB = 0x00000020, - AHC_CHNLC = 0x00000040, - AHC_EXTEND_TRANS_A = 0x00000100, - AHC_EXTEND_TRANS_B = 0x00000200, - AHC_TERM_ENB_A = 0x00000400, - AHC_TERM_ENB_SE_LOW = 0x00000400, - AHC_TERM_ENB_B = 0x00000800, - AHC_TERM_ENB_SE_HIGH = 0x00000800, - AHC_HANDLING_REQINITS = 0x00001000, - AHC_TARGETMODE = 0x00002000, - AHC_NEWEEPROM_FMT = 0x00004000, - /* - * Here ends the FreeBSD defined flags and here begins the linux defined - * flags. NOTE: I did not preserve the old flag name during this change - * specifically to force me to evaluate what flags were being used properly - * and what flags weren't. This way, I could clean up the flag usage on - * a use by use basis. Doug Ledford - */ - AHC_MOTHERBOARD = 0x00020000, - AHC_NO_STPWEN = 0x00040000, - AHC_RESET_DELAY = 0x00080000, - AHC_A_SCANNED = 0x00100000, - AHC_B_SCANNED = 0x00200000, - AHC_MULTI_CHANNEL = 0x00400000, - AHC_BIOS_ENABLED = 0x00800000, - AHC_SEEPROM_FOUND = 0x01000000, - AHC_TERM_ENB_LVD = 0x02000000, - AHC_ABORT_PENDING = 0x04000000, - AHC_RESET_PENDING = 0x08000000, -#define AHC_IN_ISR_BIT 28 - AHC_IN_ISR = 0x10000000, - AHC_IN_ABORT = 0x20000000, - AHC_IN_RESET = 0x40000000, - AHC_EXTERNAL_SRAM = 0x80000000 -} ahc_flag_type; - -typedef enum { - AHC_NONE = 0x0000, - AHC_CHIPID_MASK = 0x00ff, - AHC_AIC7770 = 0x0001, - AHC_AIC7850 = 0x0002, - AHC_AIC7860 = 0x0003, - AHC_AIC7870 = 0x0004, - AHC_AIC7880 = 0x0005, - AHC_AIC7890 = 0x0006, - AHC_AIC7895 = 0x0007, - AHC_AIC7896 = 0x0008, - AHC_AIC7892 = 0x0009, - AHC_AIC7899 = 0x000a, - AHC_VL = 0x0100, - AHC_EISA = 0x0200, - AHC_PCI = 0x0400, -} ahc_chip; - -typedef enum { - AHC_FENONE = 0x0000, - AHC_ULTRA = 0x0001, - AHC_ULTRA2 = 0x0002, - AHC_WIDE = 0x0004, - AHC_TWIN = 0x0008, - AHC_MORE_SRAM = 0x0010, - AHC_CMD_CHAN = 0x0020, - AHC_QUEUE_REGS = 0x0040, - AHC_SG_PRELOAD = 0x0080, - AHC_SPIOCAP = 0x0100, - AHC_ULTRA3 = 0x0200, - AHC_NEW_AUTOTERM = 0x0400, - AHC_AIC7770_FE = AHC_FENONE, - AHC_AIC7850_FE = AHC_SPIOCAP, - AHC_AIC7860_FE = AHC_ULTRA|AHC_SPIOCAP, - AHC_AIC7870_FE = AHC_FENONE, - AHC_AIC7880_FE = AHC_ULTRA, - AHC_AIC7890_FE = AHC_MORE_SRAM|AHC_CMD_CHAN|AHC_ULTRA2| - AHC_QUEUE_REGS|AHC_SG_PRELOAD|AHC_NEW_AUTOTERM, - AHC_AIC7895_FE = AHC_MORE_SRAM|AHC_CMD_CHAN|AHC_ULTRA, - AHC_AIC7896_FE = AHC_AIC7890_FE, - AHC_AIC7892_FE = AHC_AIC7890_FE|AHC_ULTRA3, - AHC_AIC7899_FE = AHC_AIC7890_FE|AHC_ULTRA3, -} ahc_feature; - -#define SCB_DMA_ADDR(scb, addr) ((unsigned long)(addr) + (scb)->scb_dma->dma_offset) - -struct aic7xxx_scb_dma { - unsigned long dma_offset; /* Correction you have to add - * to virtual address to get - * dma handle in this region */ - dma_addr_t dma_address; /* DMA handle of the start, - * for unmap */ - unsigned int dma_len; /* DMA length */ -}; - -typedef enum { - AHC_BUG_NONE = 0x0000, - AHC_BUG_TMODE_WIDEODD = 0x0001, - AHC_BUG_AUTOFLUSH = 0x0002, - AHC_BUG_CACHETHEN = 0x0004, - AHC_BUG_CACHETHEN_DIS = 0x0008, - AHC_BUG_PCI_2_1_RETRY = 0x0010, - AHC_BUG_PCI_MWI = 0x0020, - AHC_BUG_SCBCHAN_UPLOAD = 0x0040, -} ahc_bugs; - -struct aic7xxx_scb { - struct aic7xxx_hwscb *hscb; /* corresponding hardware scb */ - struct scsi_cmnd *cmd; /* scsi_cmnd for this scb */ - struct aic7xxx_scb *q_next; /* next scb in queue */ - volatile scb_flag_type flags; /* current state of scb */ - struct hw_scatterlist *sg_list; /* SG list in adapter format */ - unsigned char tag_action; - unsigned char sg_count; - unsigned char *sense_cmd; /* - * Allocate 6 characters for - * sense command. - */ - unsigned char *cmnd; - unsigned int sg_length; /* - * We init this during - * buildscb so we don't have - * to calculate anything during - * underflow/overflow/stat code - */ - void *kmalloc_ptr; - struct aic7xxx_scb_dma *scb_dma; -}; - -/* - * Define a linked list of SCBs. - */ -typedef struct { - struct aic7xxx_scb *head; - struct aic7xxx_scb *tail; -} scb_queue_type; - -static struct { - unsigned char errno; - const char *errmesg; -} hard_error[] = { - { ILLHADDR, "Illegal Host Access" }, - { ILLSADDR, "Illegal Sequencer Address referenced" }, - { ILLOPCODE, "Illegal Opcode in sequencer program" }, - { SQPARERR, "Sequencer Ram Parity Error" }, - { DPARERR, "Data-Path Ram Parity Error" }, - { MPARERR, "Scratch Ram/SCB Array Ram Parity Error" }, - { PCIERRSTAT,"PCI Error detected" }, - { CIOPARERR, "CIOBUS Parity Error" } -}; - -static unsigned char -generic_sense[] = { REQUEST_SENSE, 0, 0, 0, 255, 0 }; - -typedef struct { - scb_queue_type free_scbs; /* - * SCBs assigned to free slot on - * card (no paging required) - */ - struct aic7xxx_scb *scb_array[AIC7XXX_MAXSCB]; - struct aic7xxx_hwscb *hscbs; - unsigned char numscbs; /* current number of scbs */ - unsigned char maxhscbs; /* hardware scbs */ - unsigned char maxscbs; /* max scbs including pageable scbs */ - dma_addr_t hscbs_dma; /* DMA handle to hscbs */ - unsigned int hscbs_dma_len; /* length of the above DMA area */ - void *hscb_kmalloc_ptr; -} scb_data_type; - -struct target_cmd { - unsigned char mesg_bytes[4]; - unsigned char command[28]; -}; - -#define AHC_TRANS_CUR 0x0001 -#define AHC_TRANS_ACTIVE 0x0002 -#define AHC_TRANS_GOAL 0x0004 -#define AHC_TRANS_USER 0x0008 -#define AHC_TRANS_QUITE 0x0010 -typedef struct { - unsigned char width; - unsigned char period; - unsigned char offset; - unsigned char options; -} transinfo_type; - -struct aic_dev_data { - volatile scb_queue_type delayed_scbs; - volatile unsigned short temp_q_depth; - unsigned short max_q_depth; - volatile unsigned char active_cmds; - /* - * Statistics Kept: - * - * Total Xfers (count for each command that has a data xfer), - * broken down by reads && writes. - * - * Further sorted into a few bins for keeping tabs on how many commands - * we get of various sizes. - * - */ - long w_total; /* total writes */ - long r_total; /* total reads */ - long barrier_total; /* total num of REQ_BARRIER commands */ - long ordered_total; /* How many REQ_BARRIER commands we - used ordered tags to satisfy */ - long w_bins[6]; /* binned write */ - long r_bins[6]; /* binned reads */ - transinfo_type cur; - transinfo_type goal; -#define BUS_DEVICE_RESET_PENDING 0x01 -#define DEVICE_RESET_DELAY 0x02 -#define DEVICE_PRINT_DTR 0x04 -#define DEVICE_WAS_BUSY 0x08 -#define DEVICE_DTR_SCANNED 0x10 -#define DEVICE_SCSI_3 0x20 - volatile unsigned char flags; - unsigned needppr:1; - unsigned needppr_copy:1; - unsigned needsdtr:1; - unsigned needsdtr_copy:1; - unsigned needwdtr:1; - unsigned needwdtr_copy:1; - unsigned dtr_pending:1; - struct scsi_device *SDptr; - struct list_head list; -}; - -/* - * Define a structure used for each host adapter. Note, in order to avoid - * problems with architectures I can't test on (because I don't have one, - * such as the Alpha based systems) which happen to give faults for - * non-aligned memory accesses, care was taken to align this structure - * in a way that guaranteed all accesses larger than 8 bits were aligned - * on the appropriate boundary. It's also organized to try and be more - * cache line efficient. Be careful when changing this lest you might hurt - * overall performance and bring down the wrath of the masses. - */ -struct aic7xxx_host { - /* - * This is the first 64 bytes in the host struct - */ - - /* - * We are grouping things here....first, items that get either read or - * written with nearly every interrupt - */ - volatile long flags; - ahc_feature features; /* chip features */ - unsigned long base; /* card base address */ - volatile unsigned char __iomem *maddr; /* memory mapped address */ - unsigned long isr_count; /* Interrupt count */ - unsigned long spurious_int; - scb_data_type *scb_data; - struct aic7xxx_cmd_queue { - struct scsi_cmnd *head; - struct scsi_cmnd *tail; - } completeq; - - /* - * Things read/written on nearly every entry into aic7xxx_queue() - */ - volatile scb_queue_type waiting_scbs; - unsigned char unpause; /* unpause value for HCNTRL */ - unsigned char pause; /* pause value for HCNTRL */ - volatile unsigned char qoutfifonext; - volatile unsigned char activescbs; /* active scbs */ - volatile unsigned char max_activescbs; - volatile unsigned char qinfifonext; - volatile unsigned char *untagged_scbs; - volatile unsigned char *qoutfifo; - volatile unsigned char *qinfifo; - - unsigned char dev_last_queue_full[MAX_TARGETS]; - unsigned char dev_last_queue_full_count[MAX_TARGETS]; - unsigned short ultraenb; /* Gets downloaded to card as a bitmap */ - unsigned short discenable; /* Gets downloaded to card as a bitmap */ - transinfo_type user[MAX_TARGETS]; - - unsigned char msg_buf[13]; /* The message for the target */ - unsigned char msg_type; -#define MSG_TYPE_NONE 0x00 -#define MSG_TYPE_INITIATOR_MSGOUT 0x01 -#define MSG_TYPE_INITIATOR_MSGIN 0x02 - unsigned char msg_len; /* Length of message */ - unsigned char msg_index; /* Index into msg_buf array */ - - - /* - * We put the less frequently used host structure items - * after the more frequently used items to try and ease - * the burden on the cache subsystem. - * These entries are not *commonly* accessed, whereas - * the preceding entries are accessed very often. - */ - - unsigned int irq; /* IRQ for this adapter */ - int instance; /* aic7xxx instance number */ - int scsi_id; /* host adapter SCSI ID */ - int scsi_id_b; /* channel B for twin adapters */ - unsigned int bios_address; - int board_name_index; - unsigned short bios_control; /* bios control - SEEPROM */ - unsigned short adapter_control; /* adapter control - SEEPROM */ - struct pci_dev *pdev; - unsigned char pci_bus; - unsigned char pci_device_fn; - struct seeprom_config sc; - unsigned short sc_type; - unsigned short sc_size; - struct aic7xxx_host *next; /* allow for multiple IRQs */ - struct Scsi_Host *host; /* pointer to scsi host */ - struct list_head aic_devs; /* all aic_dev structs on host */ - int host_no; /* SCSI host number */ - unsigned long mbase; /* I/O memory address */ - ahc_chip chip; /* chip type */ - ahc_bugs bugs; - dma_addr_t fifo_dma; /* DMA handle for fifo arrays */ -}; - -/* - * Valid SCSIRATE values. (p. 3-17) - * Provides a mapping of transfer periods in ns/4 to the proper value to - * stick in the SCSIRATE reg to use that transfer rate. - */ -#define AHC_SYNCRATE_ULTRA3 0 -#define AHC_SYNCRATE_ULTRA2 1 -#define AHC_SYNCRATE_ULTRA 3 -#define AHC_SYNCRATE_FAST 6 -#define AHC_SYNCRATE_CRC 0x40 -#define AHC_SYNCRATE_SE 0x10 -static struct aic7xxx_syncrate { - /* Rates in Ultra mode have bit 8 of sxfr set */ -#define ULTRA_SXFR 0x100 - int sxfr_ultra2; - int sxfr; - unsigned char period; - const char *rate[2]; -} aic7xxx_syncrates[] = { - { 0x42, 0x000, 9, {"80.0", "160.0"} }, - { 0x13, 0x000, 10, {"40.0", "80.0"} }, - { 0x14, 0x000, 11, {"33.0", "66.6"} }, - { 0x15, 0x100, 12, {"20.0", "40.0"} }, - { 0x16, 0x110, 15, {"16.0", "32.0"} }, - { 0x17, 0x120, 18, {"13.4", "26.8"} }, - { 0x18, 0x000, 25, {"10.0", "20.0"} }, - { 0x19, 0x010, 31, {"8.0", "16.0"} }, - { 0x1a, 0x020, 37, {"6.67", "13.3"} }, - { 0x1b, 0x030, 43, {"5.7", "11.4"} }, - { 0x10, 0x040, 50, {"5.0", "10.0"} }, - { 0x00, 0x050, 56, {"4.4", "8.8" } }, - { 0x00, 0x060, 62, {"4.0", "8.0" } }, - { 0x00, 0x070, 68, {"3.6", "7.2" } }, - { 0x00, 0x000, 0, {NULL, NULL} }, -}; - -#define CTL_OF_SCB(scb) (((scb->hscb)->target_channel_lun >> 3) & 0x1), \ - (((scb->hscb)->target_channel_lun >> 4) & 0xf), \ - ((scb->hscb)->target_channel_lun & 0x07) - -#define CTL_OF_CMD(cmd) ((cmd->device->channel) & 0x01), \ - ((cmd->device->id) & 0x0f), \ - ((cmd->device->lun) & 0x07) - -#define TARGET_INDEX(cmd) ((cmd)->device->id | ((cmd)->device->channel << 3)) - -/* - * A nice little define to make doing our printks a little easier - */ - -#define WARN_LEAD KERN_WARNING "(scsi%d:%d:%d:%d) " -#define INFO_LEAD KERN_INFO "(scsi%d:%d:%d:%d) " - -/* - * XXX - these options apply unilaterally to _all_ 274x/284x/294x - * cards in the system. This should be fixed. Exceptions to this - * rule are noted in the comments. - */ - -/* - * Use this as the default queue depth when setting tagged queueing on. - */ -static unsigned int aic7xxx_default_queue_depth = AIC7XXX_CMDS_PER_DEVICE; - -/* - * Skip the scsi bus reset. Non 0 make us skip the reset at startup. This - * has no effect on any later resets that might occur due to things like - * SCSI bus timeouts. - */ -static unsigned int aic7xxx_no_reset = 0; -/* - * Certain PCI motherboards will scan PCI devices from highest to lowest, - * others scan from lowest to highest, and they tend to do all kinds of - * strange things when they come into contact with PCI bridge chips. The - * net result of all this is that the PCI card that is actually used to boot - * the machine is very hard to detect. Most motherboards go from lowest - * PCI slot number to highest, and the first SCSI controller found is the - * one you boot from. The only exceptions to this are when a controller - * has its BIOS disabled. So, we by default sort all of our SCSI controllers - * from lowest PCI slot number to highest PCI slot number. We also force - * all controllers with their BIOS disabled to the end of the list. This - * works on *almost* all computers. Where it doesn't work, we have this - * option. Setting this option to non-0 will reverse the order of the sort - * to highest first, then lowest, but will still leave cards with their BIOS - * disabled at the very end. That should fix everyone up unless there are - * really strange cirumstances. - */ -static int aic7xxx_reverse_scan = 0; -/* - * Should we force EXTENDED translation on a controller. - * 0 == Use whatever is in the SEEPROM or default to off - * 1 == Use whatever is in the SEEPROM or default to on - */ -static unsigned int aic7xxx_extended = 0; -/* - * The IRQ trigger method used on EISA controllers. Does not effect PCI cards. - * -1 = Use detected settings. - * 0 = Force Edge triggered mode. - * 1 = Force Level triggered mode. - */ -static int aic7xxx_irq_trigger = -1; -/* - * This variable is used to override the termination settings on a controller. - * This should not be used under normal conditions. However, in the case - * that a controller does not have a readable SEEPROM (so that we can't - * read the SEEPROM settings directly) and that a controller has a buggered - * version of the cable detection logic, this can be used to force the - * correct termination. It is preferable to use the manual termination - * settings in the BIOS if possible, but some motherboard controllers store - * those settings in a format we can't read. In other cases, auto term - * should also work, but the chipset was put together with no auto term - * logic (common on motherboard controllers). In those cases, we have - * 32 bits here to work with. That's good for 8 controllers/channels. The - * bits are organized as 4 bits per channel, with scsi0 getting the lowest - * 4 bits in the int. A 1 in a bit position indicates the termination setting - * that corresponds to that bit should be enabled, a 0 is disabled. - * It looks something like this: - * - * 0x0f = 1111-Single Ended Low Byte Termination on/off - * ||\-Single Ended High Byte Termination on/off - * |\-LVD Low Byte Termination on/off - * \-LVD High Byte Termination on/off - * - * For non-Ultra2 controllers, the upper 2 bits are not important. So, to - * enable both high byte and low byte termination on scsi0, I would need to - * make sure that the override_term variable was set to 0x03 (bits 0011). - * To make sure that all termination is enabled on an Ultra2 controller at - * scsi2 and only high byte termination on scsi1 and high and low byte - * termination on scsi0, I would set override_term=0xf23 (bits 1111 0010 0011) - * - * For the most part, users should never have to use this, that's why I - * left it fairly cryptic instead of easy to understand. If you need it, - * most likely someone will be telling you what your's needs to be set to. - */ -static int aic7xxx_override_term = -1; -/* - * Certain motherboard chipset controllers tend to screw - * up the polarity of the term enable output pin. Use this variable - * to force the correct polarity for your system. This is a bitfield variable - * similar to the previous one, but this one has one bit per channel instead - * of four. - * 0 = Force the setting to active low. - * 1 = Force setting to active high. - * Most Adaptec cards are active high, several motherboards are active low. - * To force a 2940 card at SCSI 0 to active high and a motherboard 7895 - * controller at scsi1 and scsi2 to active low, and a 2910 card at scsi3 - * to active high, you would need to set stpwlev=0x9 (bits 1001). - * - * People shouldn't need to use this, but if you are experiencing lots of - * SCSI timeout problems, this may help. There is one sure way to test what - * this option needs to be. Using a boot floppy to boot the system, configure - * your system to enable all SCSI termination (in the Adaptec SCSI BIOS) and - * if needed then also pass a value to override_term to make sure that the - * driver is enabling SCSI termination, then set this variable to either 0 - * or 1. When the driver boots, make sure there are *NO* SCSI cables - * connected to your controller. If it finds and inits the controller - * without problem, then the setting you passed to stpwlev was correct. If - * the driver goes into a reset loop and hangs the system, then you need the - * other setting for this variable. If neither setting lets the machine - * boot then you have definite termination problems that may not be fixable. - */ -static int aic7xxx_stpwlev = -1; -/* - * Set this to non-0 in order to force the driver to panic the kernel - * and print out debugging info on a SCSI abort or reset cycle. - */ -static int aic7xxx_panic_on_abort = 0; -/* - * PCI bus parity checking of the Adaptec controllers. This is somewhat - * dubious at best. To my knowledge, this option has never actually - * solved a PCI parity problem, but on certain machines with broken PCI - * chipset configurations, it can generate tons of false error messages. - * It's included in the driver for completeness. - * 0 = Shut off PCI parity check - * -1 = Normal polarity pci parity checking - * 1 = reverse polarity pci parity checking - * - * NOTE: you can't actually pass -1 on the lilo prompt. So, to set this - * variable to -1 you would actually want to simply pass the variable - * name without a number. That will invert the 0 which will result in - * -1. - */ -static int aic7xxx_pci_parity = 0; -/* - * Set this to any non-0 value to cause us to dump the contents of all - * the card's registers in a hex dump format tailored to each model of - * controller. - * - * NOTE: THE CONTROLLER IS LEFT IN AN UNUSABLE STATE BY THIS OPTION. - * YOU CANNOT BOOT UP WITH THIS OPTION, IT IS FOR DEBUGGING PURPOSES - * ONLY - */ -static int aic7xxx_dump_card = 0; -/* - * Set this to a non-0 value to make us dump out the 32 bit instruction - * registers on the card after completing the sequencer download. This - * allows the actual sequencer download to be verified. It is possible - * to use this option and still boot up and run your system. This is - * only intended for debugging purposes. - */ -static int aic7xxx_dump_sequencer = 0; -/* - * Certain newer motherboards have put new PCI based devices into the - * IO spaces that used to typically be occupied by VLB or EISA cards. - * This overlap can cause these newer motherboards to lock up when scanned - * for older EISA and VLB devices. Setting this option to non-0 will - * cause the driver to skip scanning for any VLB or EISA controllers and - * only support the PCI controllers. NOTE: this means that if the kernel - * os compiled with PCI support disabled, then setting this to non-0 - * would result in never finding any devices :) - */ -static int aic7xxx_no_probe = 0; -/* - * On some machines, enabling the external SCB RAM isn't reliable yet. I - * haven't had time to make test patches for things like changing the - * timing mode on that external RAM either. Some of those changes may - * fix the problem. Until then though, we default to external SCB RAM - * off and give a command line option to enable it. - */ -static int aic7xxx_scbram = 0; -/* - * So that we can set how long each device is given as a selection timeout. - * The table of values goes like this: - * 0 - 256ms - * 1 - 128ms - * 2 - 64ms - * 3 - 32ms - * We default to 64ms because it's fast. Some old SCSI-I devices need a - * longer time. The final value has to be left shifted by 3, hence 0x10 - * is the final value. - */ -static int aic7xxx_seltime = 0x10; -/* - * So that insmod can find the variable and make it point to something - */ -#ifdef MODULE -static char * aic7xxx = NULL; -module_param(aic7xxx, charp, 0); -#endif - -#define VERBOSE_NORMAL 0x0000 -#define VERBOSE_NEGOTIATION 0x0001 -#define VERBOSE_SEQINT 0x0002 -#define VERBOSE_SCSIINT 0x0004 -#define VERBOSE_PROBE 0x0008 -#define VERBOSE_PROBE2 0x0010 -#define VERBOSE_NEGOTIATION2 0x0020 -#define VERBOSE_MINOR_ERROR 0x0040 -#define VERBOSE_TRACING 0x0080 -#define VERBOSE_ABORT 0x0f00 -#define VERBOSE_ABORT_MID 0x0100 -#define VERBOSE_ABORT_FIND 0x0200 -#define VERBOSE_ABORT_PROCESS 0x0400 -#define VERBOSE_ABORT_RETURN 0x0800 -#define VERBOSE_RESET 0xf000 -#define VERBOSE_RESET_MID 0x1000 -#define VERBOSE_RESET_FIND 0x2000 -#define VERBOSE_RESET_PROCESS 0x4000 -#define VERBOSE_RESET_RETURN 0x8000 -static int aic7xxx_verbose = VERBOSE_NORMAL | VERBOSE_NEGOTIATION | - VERBOSE_PROBE; /* verbose messages */ - - -/**************************************************************************** - * - * We're going to start putting in function declarations so that order of - * functions is no longer important. As needed, they are added here. - * - ***************************************************************************/ - -static int aic7xxx_release(struct Scsi_Host *host); -static void aic7xxx_set_syncrate(struct aic7xxx_host *p, - struct aic7xxx_syncrate *syncrate, int target, int channel, - unsigned int period, unsigned int offset, unsigned char options, - unsigned int type, struct aic_dev_data *aic_dev); -static void aic7xxx_set_width(struct aic7xxx_host *p, int target, int channel, - int lun, unsigned int width, unsigned int type, - struct aic_dev_data *aic_dev); -static void aic7xxx_panic_abort(struct aic7xxx_host *p, struct scsi_cmnd *cmd); -static void aic7xxx_print_card(struct aic7xxx_host *p); -static void aic7xxx_print_scratch_ram(struct aic7xxx_host *p); -static void aic7xxx_print_sequencer(struct aic7xxx_host *p, int downloaded); -#ifdef AIC7XXX_VERBOSE_DEBUGGING -static void aic7xxx_check_scbs(struct aic7xxx_host *p, char *buffer); -#endif - -/**************************************************************************** - * - * These functions are now used. They happen to be wrapped in useless - * inb/outb port read/writes around the real reads and writes because it - * seems that certain very fast CPUs have a problem dealing with us when - * going at full speed. - * - ***************************************************************************/ - -static unsigned char -aic_inb(struct aic7xxx_host *p, long port) -{ -#ifdef MMAPIO - unsigned char x; - if(p->maddr) - { - x = readb(p->maddr + port); - } - else - { - x = inb(p->base + port); - } - return(x); -#else - return(inb(p->base + port)); -#endif -} - -static void -aic_outb(struct aic7xxx_host *p, unsigned char val, long port) -{ -#ifdef MMAPIO - if(p->maddr) - { - writeb(val, p->maddr + port); - mb(); /* locked operation in order to force CPU ordering */ - readb(p->maddr + HCNTRL); /* dummy read to flush the PCI write */ - } - else - { - outb(val, p->base + port); - mb(); /* locked operation in order to force CPU ordering */ - } -#else - outb(val, p->base + port); - mb(); /* locked operation in order to force CPU ordering */ -#endif -} - -/*+F************************************************************************* - * Function: - * aic7xxx_setup - * - * Description: - * Handle Linux boot parameters. This routine allows for assigning a value - * to a parameter with a ':' between the parameter and the value. - * ie. aic7xxx=unpause:0x0A,extended - *-F*************************************************************************/ -static int -aic7xxx_setup(char *s) -{ - int i, n; - char *p; - char *end; - - static struct { - const char *name; - unsigned int *flag; - } options[] = { - { "extended", &aic7xxx_extended }, - { "no_reset", &aic7xxx_no_reset }, - { "irq_trigger", &aic7xxx_irq_trigger }, - { "verbose", &aic7xxx_verbose }, - { "reverse_scan",&aic7xxx_reverse_scan }, - { "override_term", &aic7xxx_override_term }, - { "stpwlev", &aic7xxx_stpwlev }, - { "no_probe", &aic7xxx_no_probe }, - { "panic_on_abort", &aic7xxx_panic_on_abort }, - { "pci_parity", &aic7xxx_pci_parity }, - { "dump_card", &aic7xxx_dump_card }, - { "dump_sequencer", &aic7xxx_dump_sequencer }, - { "default_queue_depth", &aic7xxx_default_queue_depth }, - { "scbram", &aic7xxx_scbram }, - { "seltime", &aic7xxx_seltime }, - { "tag_info", NULL } - }; - - end = strchr(s, '\0'); - - while ((p = strsep(&s, ",.")) != NULL) - { - for (i = 0; i < ARRAY_SIZE(options); i++) - { - n = strlen(options[i].name); - if (!strncmp(options[i].name, p, n)) - { - if (!strncmp(p, "tag_info", n)) - { - if (p[n] == ':') - { - char *base; - char *tok, *tok_end, *tok_end2; - char tok_list[] = { '.', ',', '{', '}', '\0' }; - int i, instance = -1, device = -1; - unsigned char done = FALSE; - - base = p; - tok = base + n + 1; /* Forward us just past the ':' */ - tok_end = strchr(tok, '\0'); - if (tok_end < end) - *tok_end = ','; - while(!done) - { - switch(*tok) - { - case '{': - if (instance == -1) - instance = 0; - else if (device == -1) - device = 0; - tok++; - break; - case '}': - if (device != -1) - device = -1; - else if (instance != -1) - instance = -1; - tok++; - break; - case ',': - case '.': - if (instance == -1) - done = TRUE; - else if (device >= 0) - device++; - else if (instance >= 0) - instance++; - if ( (device >= MAX_TARGETS) || - (instance >= ARRAY_SIZE(aic7xxx_tag_info)) ) - done = TRUE; - tok++; - if (!done) - { - base = tok; - } - break; - case '\0': - done = TRUE; - break; - default: - done = TRUE; - tok_end = strchr(tok, '\0'); - for(i=0; tok_list[i]; i++) - { - tok_end2 = strchr(tok, tok_list[i]); - if ( (tok_end2) && (tok_end2 < tok_end) ) - { - tok_end = tok_end2; - done = FALSE; - } - } - if ( (instance >= 0) && (device >= 0) && - (instance < ARRAY_SIZE(aic7xxx_tag_info)) && - (device < MAX_TARGETS) ) - aic7xxx_tag_info[instance].tag_commands[device] = - simple_strtoul(tok, NULL, 0) & 0xff; - tok = tok_end; - break; - } - } - while((p != base) && (p != NULL)) - p = strsep(&s, ",."); - } - } - else if (p[n] == ':') - { - *(options[i].flag) = simple_strtoul(p + n + 1, NULL, 0); - if(!strncmp(p, "seltime", n)) - { - *(options[i].flag) = (*(options[i].flag) % 4) << 3; - } - } - else if (!strncmp(p, "verbose", n)) - { - *(options[i].flag) = 0xff29; - } - else - { - *(options[i].flag) = ~(*(options[i].flag)); - if(!strncmp(p, "seltime", n)) - { - *(options[i].flag) = (*(options[i].flag) % 4) << 3; - } - } - } - } - } - return 1; -} - -__setup("aic7xxx=", aic7xxx_setup); - -/*+F************************************************************************* - * Function: - * pause_sequencer - * - * Description: - * Pause the sequencer and wait for it to actually stop - this - * is important since the sequencer can disable pausing for critical - * sections. - *-F*************************************************************************/ -static void -pause_sequencer(struct aic7xxx_host *p) -{ - aic_outb(p, p->pause, HCNTRL); - while ((aic_inb(p, HCNTRL) & PAUSE) == 0) - { - ; - } - if(p->features & AHC_ULTRA2) - { - aic_inb(p, CCSCBCTL); - } -} - -/*+F************************************************************************* - * Function: - * unpause_sequencer - * - * Description: - * Unpause the sequencer. Unremarkable, yet done often enough to - * warrant an easy way to do it. - *-F*************************************************************************/ -static void -unpause_sequencer(struct aic7xxx_host *p, int unpause_always) -{ - if (unpause_always || - ( !(aic_inb(p, INTSTAT) & (SCSIINT | SEQINT | BRKADRINT)) && - !(p->flags & AHC_HANDLING_REQINITS) ) ) - { - aic_outb(p, p->unpause, HCNTRL); - } -} - -/*+F************************************************************************* - * Function: - * restart_sequencer - * - * Description: - * Restart the sequencer program from address zero. This assumes - * that the sequencer is already paused. - *-F*************************************************************************/ -static void -restart_sequencer(struct aic7xxx_host *p) -{ - aic_outb(p, 0, SEQADDR0); - aic_outb(p, 0, SEQADDR1); - aic_outb(p, FASTMODE, SEQCTL); -} - -/* - * We include the aic7xxx_seq.c file here so that the other defines have - * already been made, and so that it comes before the code that actually - * downloads the instructions (since we don't typically use function - * prototype, our code has to be ordered that way, it's a left-over from - * the original driver days.....I should fix it some time DL). - */ -#include "aic7xxx_old/aic7xxx_seq.c" - -/*+F************************************************************************* - * Function: - * aic7xxx_check_patch - * - * Description: - * See if the next patch to download should be downloaded. - *-F*************************************************************************/ -static int -aic7xxx_check_patch(struct aic7xxx_host *p, - struct sequencer_patch **start_patch, int start_instr, int *skip_addr) -{ - struct sequencer_patch *cur_patch; - struct sequencer_patch *last_patch; - int num_patches; - - num_patches = ARRAY_SIZE(sequencer_patches); - last_patch = &sequencer_patches[num_patches]; - cur_patch = *start_patch; - - while ((cur_patch < last_patch) && (start_instr == cur_patch->begin)) - { - if (cur_patch->patch_func(p) == 0) - { - /* - * Start rejecting code. - */ - *skip_addr = start_instr + cur_patch->skip_instr; - cur_patch += cur_patch->skip_patch; - } - else - { - /* - * Found an OK patch. Advance the patch pointer to the next patch - * and wait for our instruction pointer to get here. - */ - cur_patch++; - } - } - - *start_patch = cur_patch; - if (start_instr < *skip_addr) - /* - * Still skipping - */ - return (0); - return(1); -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_download_instr - * - * Description: - * Find the next patch to download. - *-F*************************************************************************/ -static void -aic7xxx_download_instr(struct aic7xxx_host *p, int instrptr, - unsigned char *dconsts) -{ - union ins_formats instr; - struct ins_format1 *fmt1_ins; - struct ins_format3 *fmt3_ins; - unsigned char opcode; - - instr = *(union ins_formats*) &seqprog[instrptr * 4]; - - instr.integer = le32_to_cpu(instr.integer); - - fmt1_ins = &instr.format1; - fmt3_ins = NULL; - - /* Pull the opcode */ - opcode = instr.format1.opcode; - switch (opcode) - { - case AIC_OP_JMP: - case AIC_OP_JC: - case AIC_OP_JNC: - case AIC_OP_CALL: - case AIC_OP_JNE: - case AIC_OP_JNZ: - case AIC_OP_JE: - case AIC_OP_JZ: - { - struct sequencer_patch *cur_patch; - int address_offset; - unsigned int address; - int skip_addr; - int i; - - fmt3_ins = &instr.format3; - address_offset = 0; - address = fmt3_ins->address; - cur_patch = sequencer_patches; - skip_addr = 0; - - for (i = 0; i < address;) - { - aic7xxx_check_patch(p, &cur_patch, i, &skip_addr); - if (skip_addr > i) - { - int end_addr; - - end_addr = min_t(int, address, skip_addr); - address_offset += end_addr - i; - i = skip_addr; - } - else - { - i++; - } - } - address -= address_offset; - fmt3_ins->address = address; - /* Fall Through to the next code section */ - } - case AIC_OP_OR: - case AIC_OP_AND: - case AIC_OP_XOR: - case AIC_OP_ADD: - case AIC_OP_ADC: - case AIC_OP_BMOV: - if (fmt1_ins->parity != 0) - { - fmt1_ins->immediate = dconsts[fmt1_ins->immediate]; - } - fmt1_ins->parity = 0; - /* Fall Through to the next code section */ - case AIC_OP_ROL: - if ((p->features & AHC_ULTRA2) != 0) - { - int i, count; - - /* Calculate odd parity for the instruction */ - for ( i=0, count=0; i < 31; i++) - { - unsigned int mask; - - mask = 0x01 << i; - if ((instr.integer & mask) != 0) - count++; - } - if (!(count & 0x01)) - instr.format1.parity = 1; - } - else - { - if (fmt3_ins != NULL) - { - instr.integer = fmt3_ins->immediate | - (fmt3_ins->source << 8) | - (fmt3_ins->address << 16) | - (fmt3_ins->opcode << 25); - } - else - { - instr.integer = fmt1_ins->immediate | - (fmt1_ins->source << 8) | - (fmt1_ins->destination << 16) | - (fmt1_ins->ret << 24) | - (fmt1_ins->opcode << 25); - } - } - aic_outb(p, (instr.integer & 0xff), SEQRAM); - aic_outb(p, ((instr.integer >> 8) & 0xff), SEQRAM); - aic_outb(p, ((instr.integer >> 16) & 0xff), SEQRAM); - aic_outb(p, ((instr.integer >> 24) & 0xff), SEQRAM); - udelay(10); - break; - - default: - panic("aic7xxx: Unknown opcode encountered in sequencer program."); - break; - } -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_loadseq - * - * Description: - * Load the sequencer code into the controller memory. - *-F*************************************************************************/ -static void -aic7xxx_loadseq(struct aic7xxx_host *p) -{ - struct sequencer_patch *cur_patch; - int i; - int downloaded; - int skip_addr; - unsigned char download_consts[4] = {0, 0, 0, 0}; - - if (aic7xxx_verbose & VERBOSE_PROBE) - { - printk(KERN_INFO "(scsi%d) Downloading sequencer code...", p->host_no); - } -#if 0 - download_consts[TMODE_NUMCMDS] = p->num_targetcmds; -#endif - download_consts[TMODE_NUMCMDS] = 0; - cur_patch = &sequencer_patches[0]; - downloaded = 0; - skip_addr = 0; - - aic_outb(p, PERRORDIS|LOADRAM|FAILDIS|FASTMODE, SEQCTL); - aic_outb(p, 0, SEQADDR0); - aic_outb(p, 0, SEQADDR1); - - for (i = 0; i < sizeof(seqprog) / 4; i++) - { - if (aic7xxx_check_patch(p, &cur_patch, i, &skip_addr) == 0) - { - /* Skip this instruction for this configuration. */ - continue; - } - aic7xxx_download_instr(p, i, &download_consts[0]); - downloaded++; - } - - aic_outb(p, 0, SEQADDR0); - aic_outb(p, 0, SEQADDR1); - aic_outb(p, FASTMODE | FAILDIS, SEQCTL); - unpause_sequencer(p, TRUE); - mdelay(1); - pause_sequencer(p); - aic_outb(p, FASTMODE, SEQCTL); - if (aic7xxx_verbose & VERBOSE_PROBE) - { - printk(" %d instructions downloaded\n", downloaded); - } - if (aic7xxx_dump_sequencer) - aic7xxx_print_sequencer(p, downloaded); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_print_sequencer - * - * Description: - * Print the contents of the sequencer memory to the screen. - *-F*************************************************************************/ -static void -aic7xxx_print_sequencer(struct aic7xxx_host *p, int downloaded) -{ - int i, k, temp; - - aic_outb(p, PERRORDIS|LOADRAM|FAILDIS|FASTMODE, SEQCTL); - aic_outb(p, 0, SEQADDR0); - aic_outb(p, 0, SEQADDR1); - - k = 0; - for (i=0; i < downloaded; i++) - { - if ( k == 0 ) - printk("%03x: ", i); - temp = aic_inb(p, SEQRAM); - temp |= (aic_inb(p, SEQRAM) << 8); - temp |= (aic_inb(p, SEQRAM) << 16); - temp |= (aic_inb(p, SEQRAM) << 24); - printk("%08x", temp); - if ( ++k == 8 ) - { - printk("\n"); - k = 0; - } - else - printk(" "); - } - aic_outb(p, 0, SEQADDR0); - aic_outb(p, 0, SEQADDR1); - aic_outb(p, FASTMODE | FAILDIS, SEQCTL); - unpause_sequencer(p, TRUE); - mdelay(1); - pause_sequencer(p); - aic_outb(p, FASTMODE, SEQCTL); - printk("\n"); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_info - * - * Description: - * Return a string describing the driver. - *-F*************************************************************************/ -static const char * -aic7xxx_info(struct Scsi_Host *dooh) -{ - static char buffer[256]; - char *bp; - struct aic7xxx_host *p; - - bp = &buffer[0]; - p = (struct aic7xxx_host *)dooh->hostdata; - memset(bp, 0, sizeof(buffer)); - strcpy(bp, "Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) "); - strcat(bp, AIC7XXX_C_VERSION); - strcat(bp, "/"); - strcat(bp, AIC7XXX_H_VERSION); - strcat(bp, "\n"); - strcat(bp, " <"); - strcat(bp, board_names[p->board_name_index]); - strcat(bp, ">"); - - return(bp); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_find_syncrate - * - * Description: - * Look up the valid period to SCSIRATE conversion in our table - *-F*************************************************************************/ -static struct aic7xxx_syncrate * -aic7xxx_find_syncrate(struct aic7xxx_host *p, unsigned int *period, - unsigned int maxsync, unsigned char *options) -{ - struct aic7xxx_syncrate *syncrate; - int done = FALSE; - - switch(*options) - { - case MSG_EXT_PPR_OPTION_DT_CRC: - case MSG_EXT_PPR_OPTION_DT_UNITS: - if(!(p->features & AHC_ULTRA3)) - { - *options = 0; - maxsync = max_t(unsigned int, maxsync, AHC_SYNCRATE_ULTRA2); - } - break; - case MSG_EXT_PPR_OPTION_DT_CRC_QUICK: - case MSG_EXT_PPR_OPTION_DT_UNITS_QUICK: - if(!(p->features & AHC_ULTRA3)) - { - *options = 0; - maxsync = max_t(unsigned int, maxsync, AHC_SYNCRATE_ULTRA2); - } - else - { - /* - * we don't support the Quick Arbitration variants of dual edge - * clocking. As it turns out, we want to send back the - * same basic option, but without the QA attribute. - * We know that we are responding because we would never set - * these options ourself, we would only respond to them. - */ - switch(*options) - { - case MSG_EXT_PPR_OPTION_DT_CRC_QUICK: - *options = MSG_EXT_PPR_OPTION_DT_CRC; - break; - case MSG_EXT_PPR_OPTION_DT_UNITS_QUICK: - *options = MSG_EXT_PPR_OPTION_DT_UNITS; - break; - } - } - break; - default: - *options = 0; - maxsync = max_t(unsigned int, maxsync, AHC_SYNCRATE_ULTRA2); - break; - } - syncrate = &aic7xxx_syncrates[maxsync]; - while ( (syncrate->rate[0] != NULL) && - (!(p->features & AHC_ULTRA2) || syncrate->sxfr_ultra2) ) - { - if (*period <= syncrate->period) - { - switch(*options) - { - case MSG_EXT_PPR_OPTION_DT_CRC: - case MSG_EXT_PPR_OPTION_DT_UNITS: - if(!(syncrate->sxfr_ultra2 & AHC_SYNCRATE_CRC)) - { - done = TRUE; - /* - * oops, we went too low for the CRC/DualEdge signalling, so - * clear the options byte - */ - *options = 0; - /* - * We'll be sending a reply to this packet to set the options - * properly, so unilaterally set the period as well. - */ - *period = syncrate->period; - } - else - { - done = TRUE; - if(syncrate == &aic7xxx_syncrates[maxsync]) - { - *period = syncrate->period; - } - } - break; - default: - if(!(syncrate->sxfr_ultra2 & AHC_SYNCRATE_CRC)) - { - done = TRUE; - if(syncrate == &aic7xxx_syncrates[maxsync]) - { - *period = syncrate->period; - } - } - break; - } - if(done) - { - break; - } - } - syncrate++; - } - if ( (*period == 0) || (syncrate->rate[0] == NULL) || - ((p->features & AHC_ULTRA2) && (syncrate->sxfr_ultra2 == 0)) ) - { - /* - * Use async transfers for this target - */ - *options = 0; - *period = 255; - syncrate = NULL; - } - return (syncrate); -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_find_period - * - * Description: - * Look up the valid SCSIRATE to period conversion in our table - *-F*************************************************************************/ -static unsigned int -aic7xxx_find_period(struct aic7xxx_host *p, unsigned int scsirate, - unsigned int maxsync) -{ - struct aic7xxx_syncrate *syncrate; - - if (p->features & AHC_ULTRA2) - { - scsirate &= SXFR_ULTRA2; - } - else - { - scsirate &= SXFR; - } - - syncrate = &aic7xxx_syncrates[maxsync]; - while (syncrate->rate[0] != NULL) - { - if (p->features & AHC_ULTRA2) - { - if (syncrate->sxfr_ultra2 == 0) - break; - else if (scsirate == syncrate->sxfr_ultra2) - return (syncrate->period); - else if (scsirate == (syncrate->sxfr_ultra2 & ~AHC_SYNCRATE_CRC)) - return (syncrate->period); - } - else if (scsirate == (syncrate->sxfr & ~ULTRA_SXFR)) - { - return (syncrate->period); - } - syncrate++; - } - return (0); /* async */ -} - -/*+F************************************************************************* - * Function: - * aic7xxx_validate_offset - * - * Description: - * Set a valid offset value for a particular card in use and transfer - * settings in use. - *-F*************************************************************************/ -static void -aic7xxx_validate_offset(struct aic7xxx_host *p, - struct aic7xxx_syncrate *syncrate, unsigned int *offset, int wide) -{ - unsigned int maxoffset; - - /* Limit offset to what the card (and device) can do */ - if (syncrate == NULL) - { - maxoffset = 0; - } - else if (p->features & AHC_ULTRA2) - { - maxoffset = MAX_OFFSET_ULTRA2; - } - else - { - if (wide) - maxoffset = MAX_OFFSET_16BIT; - else - maxoffset = MAX_OFFSET_8BIT; - } - *offset = min(*offset, maxoffset); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_set_syncrate - * - * Description: - * Set the actual syncrate down in the card and in our host structs - *-F*************************************************************************/ -static void -aic7xxx_set_syncrate(struct aic7xxx_host *p, struct aic7xxx_syncrate *syncrate, - int target, int channel, unsigned int period, unsigned int offset, - unsigned char options, unsigned int type, struct aic_dev_data *aic_dev) -{ - unsigned char tindex; - unsigned short target_mask; - unsigned char lun, old_options; - unsigned int old_period, old_offset; - - tindex = target | (channel << 3); - target_mask = 0x01 << tindex; - lun = aic_inb(p, SCB_TCL) & 0x07; - - if (syncrate == NULL) - { - period = 0; - offset = 0; - } - - old_period = aic_dev->cur.period; - old_offset = aic_dev->cur.offset; - old_options = aic_dev->cur.options; - - - if (type & AHC_TRANS_CUR) - { - unsigned int scsirate; - - scsirate = aic_inb(p, TARG_SCSIRATE + tindex); - if (p->features & AHC_ULTRA2) - { - scsirate &= ~SXFR_ULTRA2; - if (syncrate != NULL) - { - switch(options) - { - case MSG_EXT_PPR_OPTION_DT_UNITS: - /* - * mask off the CRC bit in the xfer settings - */ - scsirate |= (syncrate->sxfr_ultra2 & ~AHC_SYNCRATE_CRC); - break; - default: - scsirate |= syncrate->sxfr_ultra2; - break; - } - } - if (type & AHC_TRANS_ACTIVE) - { - aic_outb(p, offset, SCSIOFFSET); - } - aic_outb(p, offset, TARG_OFFSET + tindex); - } - else /* Not an Ultra2 controller */ - { - scsirate &= ~(SXFR|SOFS); - p->ultraenb &= ~target_mask; - if (syncrate != NULL) - { - if (syncrate->sxfr & ULTRA_SXFR) - { - p->ultraenb |= target_mask; - } - scsirate |= (syncrate->sxfr & SXFR); - scsirate |= (offset & SOFS); - } - if (type & AHC_TRANS_ACTIVE) - { - unsigned char sxfrctl0; - - sxfrctl0 = aic_inb(p, SXFRCTL0); - sxfrctl0 &= ~FAST20; - if (p->ultraenb & target_mask) - sxfrctl0 |= FAST20; - aic_outb(p, sxfrctl0, SXFRCTL0); - } - aic_outb(p, p->ultraenb & 0xff, ULTRA_ENB); - aic_outb(p, (p->ultraenb >> 8) & 0xff, ULTRA_ENB + 1 ); - } - if (type & AHC_TRANS_ACTIVE) - { - aic_outb(p, scsirate, SCSIRATE); - } - aic_outb(p, scsirate, TARG_SCSIRATE + tindex); - aic_dev->cur.period = period; - aic_dev->cur.offset = offset; - aic_dev->cur.options = options; - if ( !(type & AHC_TRANS_QUITE) && - (aic7xxx_verbose & VERBOSE_NEGOTIATION) && - (aic_dev->flags & DEVICE_PRINT_DTR) ) - { - if (offset) - { - int rate_mod = (scsirate & WIDEXFER) ? 1 : 0; - - printk(INFO_LEAD "Synchronous at %s Mbyte/sec, " - "offset %d.\n", p->host_no, channel, target, lun, - syncrate->rate[rate_mod], offset); - } - else - { - printk(INFO_LEAD "Using asynchronous transfers.\n", - p->host_no, channel, target, lun); - } - aic_dev->flags &= ~DEVICE_PRINT_DTR; - } - } - - if (type & AHC_TRANS_GOAL) - { - aic_dev->goal.period = period; - aic_dev->goal.offset = offset; - aic_dev->goal.options = options; - } - - if (type & AHC_TRANS_USER) - { - p->user[tindex].period = period; - p->user[tindex].offset = offset; - p->user[tindex].options = options; - } -} - -/*+F************************************************************************* - * Function: - * aic7xxx_set_width - * - * Description: - * Set the actual width down in the card and in our host structs - *-F*************************************************************************/ -static void -aic7xxx_set_width(struct aic7xxx_host *p, int target, int channel, int lun, - unsigned int width, unsigned int type, struct aic_dev_data *aic_dev) -{ - unsigned char tindex; - unsigned short target_mask; - unsigned int old_width; - - tindex = target | (channel << 3); - target_mask = 1 << tindex; - - old_width = aic_dev->cur.width; - - if (type & AHC_TRANS_CUR) - { - unsigned char scsirate; - - scsirate = aic_inb(p, TARG_SCSIRATE + tindex); - - scsirate &= ~WIDEXFER; - if (width == MSG_EXT_WDTR_BUS_16_BIT) - scsirate |= WIDEXFER; - - aic_outb(p, scsirate, TARG_SCSIRATE + tindex); - - if (type & AHC_TRANS_ACTIVE) - aic_outb(p, scsirate, SCSIRATE); - - aic_dev->cur.width = width; - - if ( !(type & AHC_TRANS_QUITE) && - (aic7xxx_verbose & VERBOSE_NEGOTIATION2) && - (aic_dev->flags & DEVICE_PRINT_DTR) ) - { - printk(INFO_LEAD "Using %s transfers\n", p->host_no, channel, target, - lun, (scsirate & WIDEXFER) ? "Wide(16bit)" : "Narrow(8bit)" ); - } - } - - if (type & AHC_TRANS_GOAL) - aic_dev->goal.width = width; - if (type & AHC_TRANS_USER) - p->user[tindex].width = width; - - if (aic_dev->goal.offset) - { - if (p->features & AHC_ULTRA2) - { - aic_dev->goal.offset = MAX_OFFSET_ULTRA2; - } - else if (width == MSG_EXT_WDTR_BUS_16_BIT) - { - aic_dev->goal.offset = MAX_OFFSET_16BIT; - } - else - { - aic_dev->goal.offset = MAX_OFFSET_8BIT; - } - } -} - -/*+F************************************************************************* - * Function: - * scbq_init - * - * Description: - * SCB queue initialization. - * - *-F*************************************************************************/ -static void -scbq_init(volatile scb_queue_type *queue) -{ - queue->head = NULL; - queue->tail = NULL; -} - -/*+F************************************************************************* - * Function: - * scbq_insert_head - * - * Description: - * Add an SCB to the head of the list. - * - *-F*************************************************************************/ -static inline void -scbq_insert_head(volatile scb_queue_type *queue, struct aic7xxx_scb *scb) -{ - scb->q_next = queue->head; - queue->head = scb; - if (queue->tail == NULL) /* If list was empty, update tail. */ - queue->tail = queue->head; -} - -/*+F************************************************************************* - * Function: - * scbq_remove_head - * - * Description: - * Remove an SCB from the head of the list. - * - *-F*************************************************************************/ -static inline struct aic7xxx_scb * -scbq_remove_head(volatile scb_queue_type *queue) -{ - struct aic7xxx_scb * scbp; - - scbp = queue->head; - if (queue->head != NULL) - queue->head = queue->head->q_next; - if (queue->head == NULL) /* If list is now empty, update tail. */ - queue->tail = NULL; - return(scbp); -} - -/*+F************************************************************************* - * Function: - * scbq_remove - * - * Description: - * Removes an SCB from the list. - * - *-F*************************************************************************/ -static inline void -scbq_remove(volatile scb_queue_type *queue, struct aic7xxx_scb *scb) -{ - if (queue->head == scb) - { - /* At beginning of queue, remove from head. */ - scbq_remove_head(queue); - } - else - { - struct aic7xxx_scb *curscb = queue->head; - - /* - * Search until the next scb is the one we're looking for, or - * we run out of queue. - */ - while ((curscb != NULL) && (curscb->q_next != scb)) - { - curscb = curscb->q_next; - } - if (curscb != NULL) - { - /* Found it. */ - curscb->q_next = scb->q_next; - if (scb->q_next == NULL) - { - /* Update the tail when removing the tail. */ - queue->tail = curscb; - } - } - } -} - -/*+F************************************************************************* - * Function: - * scbq_insert_tail - * - * Description: - * Add an SCB at the tail of the list. - * - *-F*************************************************************************/ -static inline void -scbq_insert_tail(volatile scb_queue_type *queue, struct aic7xxx_scb *scb) -{ - scb->q_next = NULL; - if (queue->tail != NULL) /* Add the scb at the end of the list. */ - queue->tail->q_next = scb; - queue->tail = scb; /* Update the tail. */ - if (queue->head == NULL) /* If list was empty, update head. */ - queue->head = queue->tail; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_match_scb - * - * Description: - * Checks to see if an scb matches the target/channel as specified. - * If target is ALL_TARGETS (-1), then we're looking for any device - * on the specified channel; this happens when a channel is going - * to be reset and all devices on that channel must be aborted. - *-F*************************************************************************/ -static int -aic7xxx_match_scb(struct aic7xxx_host *p, struct aic7xxx_scb *scb, - int target, int channel, int lun, unsigned char tag) -{ - int targ = (scb->hscb->target_channel_lun >> 4) & 0x0F; - int chan = (scb->hscb->target_channel_lun >> 3) & 0x01; - int slun = scb->hscb->target_channel_lun & 0x07; - int match; - - match = ((chan == channel) || (channel == ALL_CHANNELS)); - if (match != 0) - match = ((targ == target) || (target == ALL_TARGETS)); - if (match != 0) - match = ((lun == slun) || (lun == ALL_LUNS)); - if (match != 0) - match = ((tag == scb->hscb->tag) || (tag == SCB_LIST_NULL)); - - return (match); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_add_curscb_to_free_list - * - * Description: - * Adds the current scb (in SCBPTR) to the list of free SCBs. - *-F*************************************************************************/ -static void -aic7xxx_add_curscb_to_free_list(struct aic7xxx_host *p) -{ - /* - * Invalidate the tag so that aic7xxx_find_scb doesn't think - * it's active - */ - aic_outb(p, SCB_LIST_NULL, SCB_TAG); - aic_outb(p, 0, SCB_CONTROL); - - aic_outb(p, aic_inb(p, FREE_SCBH), SCB_NEXT); - aic_outb(p, aic_inb(p, SCBPTR), FREE_SCBH); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_rem_scb_from_disc_list - * - * Description: - * Removes the current SCB from the disconnected list and adds it - * to the free list. - *-F*************************************************************************/ -static unsigned char -aic7xxx_rem_scb_from_disc_list(struct aic7xxx_host *p, unsigned char scbptr, - unsigned char prev) -{ - unsigned char next; - - aic_outb(p, scbptr, SCBPTR); - next = aic_inb(p, SCB_NEXT); - aic7xxx_add_curscb_to_free_list(p); - - if (prev != SCB_LIST_NULL) - { - aic_outb(p, prev, SCBPTR); - aic_outb(p, next, SCB_NEXT); - } - else - { - aic_outb(p, next, DISCONNECTED_SCBH); - } - - return next; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_busy_target - * - * Description: - * Set the specified target busy. - *-F*************************************************************************/ -static inline void -aic7xxx_busy_target(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - p->untagged_scbs[scb->hscb->target_channel_lun] = scb->hscb->tag; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_index_busy_target - * - * Description: - * Returns the index of the busy target, and optionally sets the - * target inactive. - *-F*************************************************************************/ -static inline unsigned char -aic7xxx_index_busy_target(struct aic7xxx_host *p, unsigned char tcl, - int unbusy) -{ - unsigned char busy_scbid; - - busy_scbid = p->untagged_scbs[tcl]; - if (unbusy) - { - p->untagged_scbs[tcl] = SCB_LIST_NULL; - } - return (busy_scbid); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_find_scb - * - * Description: - * Look through the SCB array of the card and attempt to find the - * hardware SCB that corresponds to the passed in SCB. Return - * SCB_LIST_NULL if unsuccessful. This routine assumes that the - * card is already paused. - *-F*************************************************************************/ -static unsigned char -aic7xxx_find_scb(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - unsigned char saved_scbptr; - unsigned char curindex; - - saved_scbptr = aic_inb(p, SCBPTR); - curindex = 0; - for (curindex = 0; curindex < p->scb_data->maxhscbs; curindex++) - { - aic_outb(p, curindex, SCBPTR); - if (aic_inb(p, SCB_TAG) == scb->hscb->tag) - { - break; - } - } - aic_outb(p, saved_scbptr, SCBPTR); - if (curindex >= p->scb_data->maxhscbs) - { - curindex = SCB_LIST_NULL; - } - - return (curindex); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_allocate_scb - * - * Description: - * Get an SCB from the free list or by allocating a new one. - *-F*************************************************************************/ -static int -aic7xxx_allocate_scb(struct aic7xxx_host *p) -{ - struct aic7xxx_scb *scbp = NULL; - int scb_size = (sizeof (struct hw_scatterlist) * AIC7XXX_MAX_SG) + 12 + 6; - int i; - int step = PAGE_SIZE / 1024; - unsigned long scb_count = 0; - struct hw_scatterlist *hsgp; - struct aic7xxx_scb *scb_ap; - struct aic7xxx_scb_dma *scb_dma; - unsigned char *bufs; - - if (p->scb_data->numscbs < p->scb_data->maxscbs) - { - /* - * Calculate the optimal number of SCBs to allocate. - * - * NOTE: This formula works because the sizeof(sg_array) is always - * 1024. Therefore, scb_size * i would always be > PAGE_SIZE * - * (i/step). The (i-1) allows the left hand side of the equation - * to grow into the right hand side to a point of near perfect - * efficiency since scb_size * (i -1) is growing slightly faster - * than the right hand side. If the number of SG array elements - * is changed, this function may not be near so efficient any more. - * - * Since the DMA'able buffers are now allocated in a separate - * chunk this algorithm has been modified to match. The '12' - * and '6' factors in scb_size are for the DMA'able command byte - * and sensebuffers respectively. -DaveM - */ - for ( i=step;; i *= 2 ) - { - if ( (scb_size * (i-1)) >= ( (PAGE_SIZE * (i/step)) - 64 ) ) - { - i /= 2; - break; - } - } - scb_count = min( (i-1), p->scb_data->maxscbs - p->scb_data->numscbs); - scb_ap = kmalloc(sizeof (struct aic7xxx_scb) * scb_count - + sizeof(struct aic7xxx_scb_dma), GFP_ATOMIC); - if (scb_ap == NULL) - return(0); - scb_dma = (struct aic7xxx_scb_dma *)&scb_ap[scb_count]; - hsgp = (struct hw_scatterlist *) - pci_alloc_consistent(p->pdev, scb_size * scb_count, - &scb_dma->dma_address); - if (hsgp == NULL) - { - kfree(scb_ap); - return(0); - } - bufs = (unsigned char *)&hsgp[scb_count * AIC7XXX_MAX_SG]; -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - { - if (p->scb_data->numscbs == 0) - printk(INFO_LEAD "Allocating initial %ld SCB structures.\n", - p->host_no, -1, -1, -1, scb_count); - else - printk(INFO_LEAD "Allocating %ld additional SCB structures.\n", - p->host_no, -1, -1, -1, scb_count); - } -#endif - memset(scb_ap, 0, sizeof (struct aic7xxx_scb) * scb_count); - scb_dma->dma_offset = (unsigned long)scb_dma->dma_address - - (unsigned long)hsgp; - scb_dma->dma_len = scb_size * scb_count; - for (i=0; i < scb_count; i++) - { - scbp = &scb_ap[i]; - scbp->hscb = &p->scb_data->hscbs[p->scb_data->numscbs]; - scbp->sg_list = &hsgp[i * AIC7XXX_MAX_SG]; - scbp->sense_cmd = bufs; - scbp->cmnd = bufs + 6; - bufs += 12 + 6; - scbp->scb_dma = scb_dma; - memset(scbp->hscb, 0, sizeof(struct aic7xxx_hwscb)); - scbp->hscb->tag = p->scb_data->numscbs; - /* - * Place in the scb array; never is removed - */ - p->scb_data->scb_array[p->scb_data->numscbs++] = scbp; - scbq_insert_tail(&p->scb_data->free_scbs, scbp); - } - scbp->kmalloc_ptr = scb_ap; - } - return(scb_count); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_queue_cmd_complete - * - * Description: - * Due to race conditions present in the SCSI subsystem, it is easier - * to queue completed commands, then call scsi_done() on them when - * we're finished. This function queues the completed commands. - *-F*************************************************************************/ -static void -aic7xxx_queue_cmd_complete(struct aic7xxx_host *p, struct scsi_cmnd *cmd) -{ - aic7xxx_position(cmd) = SCB_LIST_NULL; - cmd->host_scribble = (char *)p->completeq.head; - p->completeq.head = cmd; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_done_cmds_complete - * - * Description: - * Process the completed command queue. - *-F*************************************************************************/ -static void aic7xxx_done_cmds_complete(struct aic7xxx_host *p) -{ - struct scsi_cmnd *cmd; - - while (p->completeq.head != NULL) { - cmd = p->completeq.head; - p->completeq.head = (struct scsi_cmnd *) cmd->host_scribble; - cmd->host_scribble = NULL; - cmd->scsi_done(cmd); - } -} - -/*+F************************************************************************* - * Function: - * aic7xxx_free_scb - * - * Description: - * Free the scb and insert into the free scb list. - *-F*************************************************************************/ -static void -aic7xxx_free_scb(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - - scb->flags = SCB_FREE; - scb->cmd = NULL; - scb->sg_count = 0; - scb->sg_length = 0; - scb->tag_action = 0; - scb->hscb->control = 0; - scb->hscb->target_status = 0; - scb->hscb->target_channel_lun = SCB_LIST_NULL; - - scbq_insert_head(&p->scb_data->free_scbs, scb); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_done - * - * Description: - * Calls the higher level scsi done function and frees the scb. - *-F*************************************************************************/ -static void -aic7xxx_done(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - struct scsi_cmnd *cmd = scb->cmd; - struct aic_dev_data *aic_dev = cmd->device->hostdata; - int tindex = TARGET_INDEX(cmd); - struct aic7xxx_scb *scbp; - unsigned char queue_depth; - - scsi_dma_unmap(cmd); - - if (scb->flags & SCB_SENSE) - { - pci_unmap_single(p->pdev, - le32_to_cpu(scb->sg_list[0].address), - SCSI_SENSE_BUFFERSIZE, - PCI_DMA_FROMDEVICE); - } - if (scb->flags & SCB_RECOVERY_SCB) - { - p->flags &= ~AHC_ABORT_PENDING; - } - if (scb->flags & (SCB_RESET|SCB_ABORT)) - { - cmd->result |= (DID_RESET << 16); - } - - if ((scb->flags & SCB_MSGOUT_BITS) != 0) - { - unsigned short mask; - int message_error = FALSE; - - mask = 0x01 << tindex; - - /* - * Check to see if we get an invalid message or a message error - * after failing to negotiate a wide or sync transfer message. - */ - if ((scb->flags & SCB_SENSE) && - ((scb->cmd->sense_buffer[12] == 0x43) || /* INVALID_MESSAGE */ - (scb->cmd->sense_buffer[12] == 0x49))) /* MESSAGE_ERROR */ - { - message_error = TRUE; - } - - if (scb->flags & SCB_MSGOUT_WDTR) - { - if (message_error) - { - if ( (aic7xxx_verbose & VERBOSE_NEGOTIATION2) && - (aic_dev->flags & DEVICE_PRINT_DTR) ) - { - printk(INFO_LEAD "Device failed to complete Wide Negotiation " - "processing and\n", p->host_no, CTL_OF_SCB(scb)); - printk(INFO_LEAD "returned a sense error code for invalid message, " - "disabling future\n", p->host_no, CTL_OF_SCB(scb)); - printk(INFO_LEAD "Wide negotiation to this device.\n", p->host_no, - CTL_OF_SCB(scb)); - } - aic_dev->needwdtr = aic_dev->needwdtr_copy = 0; - } - } - if (scb->flags & SCB_MSGOUT_SDTR) - { - if (message_error) - { - if ( (aic7xxx_verbose & VERBOSE_NEGOTIATION2) && - (aic_dev->flags & DEVICE_PRINT_DTR) ) - { - printk(INFO_LEAD "Device failed to complete Sync Negotiation " - "processing and\n", p->host_no, CTL_OF_SCB(scb)); - printk(INFO_LEAD "returned a sense error code for invalid message, " - "disabling future\n", p->host_no, CTL_OF_SCB(scb)); - printk(INFO_LEAD "Sync negotiation to this device.\n", p->host_no, - CTL_OF_SCB(scb)); - aic_dev->flags &= ~DEVICE_PRINT_DTR; - } - aic_dev->needsdtr = aic_dev->needsdtr_copy = 0; - } - } - if (scb->flags & SCB_MSGOUT_PPR) - { - if(message_error) - { - if ( (aic7xxx_verbose & VERBOSE_NEGOTIATION2) && - (aic_dev->flags & DEVICE_PRINT_DTR) ) - { - printk(INFO_LEAD "Device failed to complete Parallel Protocol " - "Request processing and\n", p->host_no, CTL_OF_SCB(scb)); - printk(INFO_LEAD "returned a sense error code for invalid message, " - "disabling future\n", p->host_no, CTL_OF_SCB(scb)); - printk(INFO_LEAD "Parallel Protocol Request negotiation to this " - "device.\n", p->host_no, CTL_OF_SCB(scb)); - } - /* - * Disable PPR negotiation and revert back to WDTR and SDTR setup - */ - aic_dev->needppr = aic_dev->needppr_copy = 0; - aic_dev->needsdtr = aic_dev->needsdtr_copy = 1; - aic_dev->needwdtr = aic_dev->needwdtr_copy = 1; - } - } - } - - queue_depth = aic_dev->temp_q_depth; - if (queue_depth >= aic_dev->active_cmds) - { - scbp = scbq_remove_head(&aic_dev->delayed_scbs); - if (scbp) - { - if (queue_depth == 1) - { - /* - * Give extra preference to untagged devices, such as CD-R devices - * This makes it more likely that a drive *won't* stuff up while - * waiting on data at a critical time, such as CD-R writing and - * audio CD ripping operations. Should also benefit tape drives. - */ - scbq_insert_head(&p->waiting_scbs, scbp); - } - else - { - scbq_insert_tail(&p->waiting_scbs, scbp); - } -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - printk(INFO_LEAD "Moving SCB from delayed to waiting queue.\n", - p->host_no, CTL_OF_SCB(scbp)); -#endif - if (queue_depth > aic_dev->active_cmds) - { - scbp = scbq_remove_head(&aic_dev->delayed_scbs); - if (scbp) - scbq_insert_tail(&p->waiting_scbs, scbp); - } - } - } - if (!(scb->tag_action)) - { - aic7xxx_index_busy_target(p, scb->hscb->target_channel_lun, - /* unbusy */ TRUE); - if (cmd->device->simple_tags) - { - aic_dev->temp_q_depth = aic_dev->max_q_depth; - } - } - if(scb->flags & SCB_DTR_SCB) - { - aic_dev->dtr_pending = 0; - } - aic_dev->active_cmds--; - p->activescbs--; - - if ((scb->sg_length >= 512) && (((cmd->result >> 16) & 0xf) == DID_OK)) - { - long *ptr; - int x, i; - - - if (rq_data_dir(cmd->request) == WRITE) - { - aic_dev->w_total++; - ptr = aic_dev->w_bins; - } - else - { - aic_dev->r_total++; - ptr = aic_dev->r_bins; - } - x = scb->sg_length; - x >>= 10; - for(i=0; i<6; i++) - { - x >>= 2; - if(!x) { - ptr[i]++; - break; - } - } - if(i == 6 && x) - ptr[5]++; - } - aic7xxx_free_scb(p, scb); - aic7xxx_queue_cmd_complete(p, cmd); - -} - -/*+F************************************************************************* - * Function: - * aic7xxx_run_done_queue - * - * Description: - * Calls the aic7xxx_done() for the scsi_cmnd of each scb in the - * aborted list, and adds each scb to the free list. If complete - * is TRUE, we also process the commands complete list. - *-F*************************************************************************/ -static void -aic7xxx_run_done_queue(struct aic7xxx_host *p, /*complete*/ int complete) -{ - struct aic7xxx_scb *scb; - int i, found = 0; - - for (i = 0; i < p->scb_data->numscbs; i++) - { - scb = p->scb_data->scb_array[i]; - if (scb->flags & SCB_QUEUED_FOR_DONE) - { - if (scb->flags & SCB_QUEUE_FULL) - { - scb->cmd->result = QUEUE_FULL << 1; - } - else - { - if (aic7xxx_verbose & (VERBOSE_ABORT_PROCESS | VERBOSE_RESET_PROCESS)) - printk(INFO_LEAD "Aborting scb %d\n", - p->host_no, CTL_OF_SCB(scb), scb->hscb->tag); - /* - * Clear any residual information since the normal aic7xxx_done() path - * doesn't touch the residuals. - */ - scb->hscb->residual_SG_segment_count = 0; - scb->hscb->residual_data_count[0] = 0; - scb->hscb->residual_data_count[1] = 0; - scb->hscb->residual_data_count[2] = 0; - } - found++; - aic7xxx_done(p, scb); - } - } - if (aic7xxx_verbose & (VERBOSE_ABORT_RETURN | VERBOSE_RESET_RETURN)) - { - printk(INFO_LEAD "%d commands found and queued for " - "completion.\n", p->host_no, -1, -1, -1, found); - } - if (complete) - { - aic7xxx_done_cmds_complete(p); - } -} - -/*+F************************************************************************* - * Function: - * aic7xxx_abort_waiting_scb - * - * Description: - * Manipulate the waiting for selection list and return the - * scb that follows the one that we remove. - *-F*************************************************************************/ -static unsigned char -aic7xxx_abort_waiting_scb(struct aic7xxx_host *p, struct aic7xxx_scb *scb, - unsigned char scbpos, unsigned char prev) -{ - unsigned char curscb, next; - - /* - * Select the SCB we want to abort and pull the next pointer out of it. - */ - curscb = aic_inb(p, SCBPTR); - aic_outb(p, scbpos, SCBPTR); - next = aic_inb(p, SCB_NEXT); - - aic7xxx_add_curscb_to_free_list(p); - - /* - * Update the waiting list - */ - if (prev == SCB_LIST_NULL) - { - /* - * First in the list - */ - aic_outb(p, next, WAITING_SCBH); - } - else - { - /* - * Select the scb that pointed to us and update its next pointer. - */ - aic_outb(p, prev, SCBPTR); - aic_outb(p, next, SCB_NEXT); - } - /* - * Point us back at the original scb position and inform the SCSI - * system that the command has been aborted. - */ - aic_outb(p, curscb, SCBPTR); - return (next); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_search_qinfifo - * - * Description: - * Search the queue-in FIFO for matching SCBs and conditionally - * requeue. Returns the number of matching SCBs. - *-F*************************************************************************/ -static int -aic7xxx_search_qinfifo(struct aic7xxx_host *p, int target, int channel, - int lun, unsigned char tag, int flags, int requeue, - volatile scb_queue_type *queue) -{ - int found; - unsigned char qinpos, qintail; - struct aic7xxx_scb *scbp; - - found = 0; - qinpos = aic_inb(p, QINPOS); - qintail = p->qinfifonext; - - p->qinfifonext = qinpos; - - while (qinpos != qintail) - { - scbp = p->scb_data->scb_array[p->qinfifo[qinpos++]]; - if (aic7xxx_match_scb(p, scbp, target, channel, lun, tag)) - { - /* - * We found an scb that needs to be removed. - */ - if (requeue && (queue != NULL)) - { - if (scbp->flags & SCB_WAITINGQ) - { - scbq_remove(queue, scbp); - scbq_remove(&p->waiting_scbs, scbp); - scbq_remove(&AIC_DEV(scbp->cmd)->delayed_scbs, scbp); - AIC_DEV(scbp->cmd)->active_cmds++; - p->activescbs++; - } - scbq_insert_tail(queue, scbp); - AIC_DEV(scbp->cmd)->active_cmds--; - p->activescbs--; - scbp->flags |= SCB_WAITINGQ; - if ( !(scbp->tag_action & TAG_ENB) ) - { - aic7xxx_index_busy_target(p, scbp->hscb->target_channel_lun, - TRUE); - } - } - else if (requeue) - { - p->qinfifo[p->qinfifonext++] = scbp->hscb->tag; - } - else - { - /* - * Preserve any SCB_RECOVERY_SCB flags on this scb then set the - * flags we were called with, presumeably so aic7xxx_run_done_queue - * can find this scb - */ - scbp->flags = flags | (scbp->flags & SCB_RECOVERY_SCB); - if (aic7xxx_index_busy_target(p, scbp->hscb->target_channel_lun, - FALSE) == scbp->hscb->tag) - { - aic7xxx_index_busy_target(p, scbp->hscb->target_channel_lun, - TRUE); - } - } - found++; - } - else - { - p->qinfifo[p->qinfifonext++] = scbp->hscb->tag; - } - } - /* - * Now that we've done the work, clear out any left over commands in the - * qinfifo and update the KERNEL_QINPOS down on the card. - * - * NOTE: This routine expect the sequencer to already be paused when - * it is run....make sure it's that way! - */ - qinpos = p->qinfifonext; - while(qinpos != qintail) - { - p->qinfifo[qinpos++] = SCB_LIST_NULL; - } - if (p->features & AHC_QUEUE_REGS) - aic_outb(p, p->qinfifonext, HNSCB_QOFF); - else - aic_outb(p, p->qinfifonext, KERNEL_QINPOS); - - return (found); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_scb_on_qoutfifo - * - * Description: - * Is the scb that was passed to us currently on the qoutfifo? - *-F*************************************************************************/ -static int -aic7xxx_scb_on_qoutfifo(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - int i=0; - - while(p->qoutfifo[(p->qoutfifonext + i) & 0xff ] != SCB_LIST_NULL) - { - if(p->qoutfifo[(p->qoutfifonext + i) & 0xff ] == scb->hscb->tag) - return TRUE; - else - i++; - } - return FALSE; -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_reset_device - * - * Description: - * The device at the given target/channel has been reset. Abort - * all active and queued scbs for that target/channel. This function - * need not worry about linked next pointers because if was a MSG_ABORT_TAG - * then we had a tagged command (no linked next), if it was MSG_ABORT or - * MSG_BUS_DEV_RESET then the device won't know about any commands any more - * and no busy commands will exist, and if it was a bus reset, then nothing - * knows about any linked next commands any more. In all cases, we don't - * need to worry about the linked next or busy scb, we just need to clear - * them. - *-F*************************************************************************/ -static void -aic7xxx_reset_device(struct aic7xxx_host *p, int target, int channel, - int lun, unsigned char tag) -{ - struct aic7xxx_scb *scbp, *prev_scbp; - struct scsi_device *sd; - unsigned char active_scb, tcl, scb_tag; - int i = 0, init_lists = FALSE; - struct aic_dev_data *aic_dev; - - /* - * Restore this when we're done - */ - active_scb = aic_inb(p, SCBPTR); - scb_tag = aic_inb(p, SCB_TAG); - - if (aic7xxx_verbose & (VERBOSE_RESET_PROCESS | VERBOSE_ABORT_PROCESS)) - { - printk(INFO_LEAD "Reset device, hardware_scb %d,\n", - p->host_no, channel, target, lun, active_scb); - printk(INFO_LEAD "Current scb %d, SEQADDR 0x%x, LASTPHASE " - "0x%x\n", - p->host_no, channel, target, lun, scb_tag, - aic_inb(p, SEQADDR0) | (aic_inb(p, SEQADDR1) << 8), - aic_inb(p, LASTPHASE)); - printk(INFO_LEAD "SG_CACHEPTR 0x%x, SG_COUNT %d, SCSISIGI 0x%x\n", - p->host_no, channel, target, lun, - (p->features & AHC_ULTRA2) ? aic_inb(p, SG_CACHEPTR) : 0, - aic_inb(p, SG_COUNT), aic_inb(p, SCSISIGI)); - printk(INFO_LEAD "SSTAT0 0x%x, SSTAT1 0x%x, SSTAT2 0x%x\n", - p->host_no, channel, target, lun, aic_inb(p, SSTAT0), - aic_inb(p, SSTAT1), aic_inb(p, SSTAT2)); - } - - /* - * Deal with the busy target and linked next issues. - */ - list_for_each_entry(aic_dev, &p->aic_devs, list) - { - if (aic7xxx_verbose & (VERBOSE_RESET_PROCESS | VERBOSE_ABORT_PROCESS)) - printk(INFO_LEAD "processing aic_dev %p\n", p->host_no, channel, target, - lun, aic_dev); - sd = aic_dev->SDptr; - - if((target != ALL_TARGETS && target != sd->id) || - (channel != ALL_CHANNELS && channel != sd->channel)) - continue; - if (aic7xxx_verbose & (VERBOSE_ABORT_PROCESS | VERBOSE_RESET_PROCESS)) - printk(INFO_LEAD "Cleaning up status information " - "and delayed_scbs.\n", p->host_no, sd->channel, sd->id, sd->lun); - aic_dev->flags &= ~BUS_DEVICE_RESET_PENDING; - if ( tag == SCB_LIST_NULL ) - { - aic_dev->dtr_pending = 0; - aic_dev->needppr = aic_dev->needppr_copy; - aic_dev->needsdtr = aic_dev->needsdtr_copy; - aic_dev->needwdtr = aic_dev->needwdtr_copy; - aic_dev->flags = DEVICE_PRINT_DTR; - aic_dev->temp_q_depth = aic_dev->max_q_depth; - } - tcl = (sd->id << 4) | (sd->channel << 3) | sd->lun; - if ( (aic7xxx_index_busy_target(p, tcl, FALSE) == tag) || - (tag == SCB_LIST_NULL) ) - aic7xxx_index_busy_target(p, tcl, /* unbusy */ TRUE); - prev_scbp = NULL; - scbp = aic_dev->delayed_scbs.head; - while (scbp != NULL) - { - prev_scbp = scbp; - scbp = scbp->q_next; - if (aic7xxx_match_scb(p, prev_scbp, target, channel, lun, tag)) - { - scbq_remove(&aic_dev->delayed_scbs, prev_scbp); - if (prev_scbp->flags & SCB_WAITINGQ) - { - aic_dev->active_cmds++; - p->activescbs++; - } - prev_scbp->flags &= ~(SCB_ACTIVE | SCB_WAITINGQ); - prev_scbp->flags |= SCB_RESET | SCB_QUEUED_FOR_DONE; - } - } - } - - if (aic7xxx_verbose & (VERBOSE_ABORT_PROCESS | VERBOSE_RESET_PROCESS)) - printk(INFO_LEAD "Cleaning QINFIFO.\n", p->host_no, channel, target, lun ); - aic7xxx_search_qinfifo(p, target, channel, lun, tag, - SCB_RESET | SCB_QUEUED_FOR_DONE, /* requeue */ FALSE, NULL); - -/* - * Search the waiting_scbs queue for matches, this catches any SCB_QUEUED - * ABORT/RESET commands. - */ - if (aic7xxx_verbose & (VERBOSE_ABORT_PROCESS | VERBOSE_RESET_PROCESS)) - printk(INFO_LEAD "Cleaning waiting_scbs.\n", p->host_no, channel, - target, lun ); - { - struct aic7xxx_scb *scbp, *prev_scbp; - - prev_scbp = NULL; - scbp = p->waiting_scbs.head; - while (scbp != NULL) - { - prev_scbp = scbp; - scbp = scbp->q_next; - if (aic7xxx_match_scb(p, prev_scbp, target, channel, lun, tag)) - { - scbq_remove(&p->waiting_scbs, prev_scbp); - if (prev_scbp->flags & SCB_WAITINGQ) - { - AIC_DEV(prev_scbp->cmd)->active_cmds++; - p->activescbs++; - } - prev_scbp->flags &= ~(SCB_ACTIVE | SCB_WAITINGQ); - prev_scbp->flags |= SCB_RESET | SCB_QUEUED_FOR_DONE; - } - } - } - - - /* - * Search waiting for selection list. - */ - if (aic7xxx_verbose & (VERBOSE_ABORT_PROCESS | VERBOSE_RESET_PROCESS)) - printk(INFO_LEAD "Cleaning waiting for selection " - "list.\n", p->host_no, channel, target, lun); - { - unsigned char next, prev, scb_index; - - next = aic_inb(p, WAITING_SCBH); /* Start at head of list. */ - prev = SCB_LIST_NULL; - while (next != SCB_LIST_NULL) - { - aic_outb(p, next, SCBPTR); - scb_index = aic_inb(p, SCB_TAG); - if (scb_index >= p->scb_data->numscbs) - { - /* - * No aic7xxx_verbose check here.....we want to see this since it - * means either the kernel driver or the sequencer screwed things up - */ - printk(WARN_LEAD "Waiting List inconsistency; SCB index=%d, " - "numscbs=%d\n", p->host_no, channel, target, lun, scb_index, - p->scb_data->numscbs); - next = aic_inb(p, SCB_NEXT); - aic7xxx_add_curscb_to_free_list(p); - } - else - { - scbp = p->scb_data->scb_array[scb_index]; - if (aic7xxx_match_scb(p, scbp, target, channel, lun, tag)) - { - next = aic7xxx_abort_waiting_scb(p, scbp, next, prev); - if (scbp->flags & SCB_WAITINGQ) - { - AIC_DEV(scbp->cmd)->active_cmds++; - p->activescbs++; - } - scbp->flags &= ~(SCB_ACTIVE | SCB_WAITINGQ); - scbp->flags |= SCB_RESET | SCB_QUEUED_FOR_DONE; - if (prev == SCB_LIST_NULL) - { - /* - * This is either the first scb on the waiting list, or we - * have already yanked the first and haven't left any behind. - * Either way, we need to turn off the selection hardware if - * it isn't already off. - */ - aic_outb(p, aic_inb(p, SCSISEQ) & ~ENSELO, SCSISEQ); - aic_outb(p, CLRSELTIMEO, CLRSINT1); - } - } - else - { - prev = next; - next = aic_inb(p, SCB_NEXT); - } - } - } - } - - /* - * Go through disconnected list and remove any entries we have queued - * for completion, zeroing their control byte too. - */ - if (aic7xxx_verbose & (VERBOSE_ABORT_PROCESS | VERBOSE_RESET_PROCESS)) - printk(INFO_LEAD "Cleaning disconnected scbs " - "list.\n", p->host_no, channel, target, lun); - if (p->flags & AHC_PAGESCBS) - { - unsigned char next, prev, scb_index; - - next = aic_inb(p, DISCONNECTED_SCBH); - prev = SCB_LIST_NULL; - while (next != SCB_LIST_NULL) - { - aic_outb(p, next, SCBPTR); - scb_index = aic_inb(p, SCB_TAG); - if (scb_index > p->scb_data->numscbs) - { - printk(WARN_LEAD "Disconnected List inconsistency; SCB index=%d, " - "numscbs=%d\n", p->host_no, channel, target, lun, scb_index, - p->scb_data->numscbs); - next = aic7xxx_rem_scb_from_disc_list(p, next, prev); - } - else - { - scbp = p->scb_data->scb_array[scb_index]; - if (aic7xxx_match_scb(p, scbp, target, channel, lun, tag)) - { - next = aic7xxx_rem_scb_from_disc_list(p, next, prev); - if (scbp->flags & SCB_WAITINGQ) - { - AIC_DEV(scbp->cmd)->active_cmds++; - p->activescbs++; - } - scbp->flags &= ~(SCB_ACTIVE | SCB_WAITINGQ); - scbp->flags |= SCB_RESET | SCB_QUEUED_FOR_DONE; - scbp->hscb->control = 0; - } - else - { - prev = next; - next = aic_inb(p, SCB_NEXT); - } - } - } - } - - /* - * Walk the free list making sure no entries on the free list have - * a valid SCB_TAG value or SCB_CONTROL byte. - */ - if (p->flags & AHC_PAGESCBS) - { - unsigned char next; - - next = aic_inb(p, FREE_SCBH); - while (next != SCB_LIST_NULL) - { - aic_outb(p, next, SCBPTR); - if (aic_inb(p, SCB_TAG) < p->scb_data->numscbs) - { - printk(WARN_LEAD "Free list inconsistency!.\n", p->host_no, channel, - target, lun); - init_lists = TRUE; - next = SCB_LIST_NULL; - } - else - { - aic_outb(p, SCB_LIST_NULL, SCB_TAG); - aic_outb(p, 0, SCB_CONTROL); - next = aic_inb(p, SCB_NEXT); - } - } - } - - /* - * Go through the hardware SCB array looking for commands that - * were active but not on any list. - */ - if (init_lists) - { - aic_outb(p, SCB_LIST_NULL, FREE_SCBH); - aic_outb(p, SCB_LIST_NULL, WAITING_SCBH); - aic_outb(p, SCB_LIST_NULL, DISCONNECTED_SCBH); - } - for (i = p->scb_data->maxhscbs - 1; i >= 0; i--) - { - unsigned char scbid; - - aic_outb(p, i, SCBPTR); - if (init_lists) - { - aic_outb(p, SCB_LIST_NULL, SCB_TAG); - aic_outb(p, SCB_LIST_NULL, SCB_NEXT); - aic_outb(p, 0, SCB_CONTROL); - aic7xxx_add_curscb_to_free_list(p); - } - else - { - scbid = aic_inb(p, SCB_TAG); - if (scbid < p->scb_data->numscbs) - { - scbp = p->scb_data->scb_array[scbid]; - if (aic7xxx_match_scb(p, scbp, target, channel, lun, tag)) - { - aic_outb(p, 0, SCB_CONTROL); - aic_outb(p, SCB_LIST_NULL, SCB_TAG); - aic7xxx_add_curscb_to_free_list(p); - } - } - } - } - - /* - * Go through the entire SCB array now and look for commands for - * for this target that are stillactive. These are other (most likely - * tagged) commands that were disconnected when the reset occurred. - * Any commands we find here we know this about, it wasn't on any queue, - * it wasn't in the qinfifo, it wasn't in the disconnected or waiting - * lists, so it really must have been a paged out SCB. In that case, - * we shouldn't need to bother with updating any counters, just mark - * the correct flags and go on. - */ - for (i = 0; i < p->scb_data->numscbs; i++) - { - scbp = p->scb_data->scb_array[i]; - if ((scbp->flags & SCB_ACTIVE) && - aic7xxx_match_scb(p, scbp, target, channel, lun, tag) && - !aic7xxx_scb_on_qoutfifo(p, scbp)) - { - if (scbp->flags & SCB_WAITINGQ) - { - scbq_remove(&p->waiting_scbs, scbp); - scbq_remove(&AIC_DEV(scbp->cmd)->delayed_scbs, scbp); - AIC_DEV(scbp->cmd)->active_cmds++; - p->activescbs++; - } - scbp->flags |= SCB_RESET | SCB_QUEUED_FOR_DONE; - scbp->flags &= ~(SCB_ACTIVE | SCB_WAITINGQ); - } - } - - aic_outb(p, active_scb, SCBPTR); -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_clear_intstat - * - * Description: - * Clears the interrupt status. - *-F*************************************************************************/ -static void -aic7xxx_clear_intstat(struct aic7xxx_host *p) -{ - /* Clear any interrupt conditions this may have caused. */ - aic_outb(p, CLRSELDO | CLRSELDI | CLRSELINGO, CLRSINT0); - aic_outb(p, CLRSELTIMEO | CLRATNO | CLRSCSIRSTI | CLRBUSFREE | CLRSCSIPERR | - CLRPHASECHG | CLRREQINIT, CLRSINT1); - aic_outb(p, CLRSCSIINT | CLRSEQINT | CLRBRKADRINT | CLRPARERR, CLRINT); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_reset_current_bus - * - * Description: - * Reset the current SCSI bus. - *-F*************************************************************************/ -static void -aic7xxx_reset_current_bus(struct aic7xxx_host *p) -{ - - /* Disable reset interrupts. */ - aic_outb(p, aic_inb(p, SIMODE1) & ~ENSCSIRST, SIMODE1); - - /* Turn off the bus' current operations, after all, we shouldn't have any - * valid commands left to cause a RSELI and SELO once we've tossed the - * bus away with this reset, so we might as well shut down the sequencer - * until the bus is restarted as opposed to saving the current settings - * and restoring them (which makes no sense to me). */ - - /* Turn on the bus reset. */ - aic_outb(p, aic_inb(p, SCSISEQ) | SCSIRSTO, SCSISEQ); - while ( (aic_inb(p, SCSISEQ) & SCSIRSTO) == 0) - mdelay(5); - - /* - * Some of the new Ultra2 chipsets need a longer delay after a chip - * reset than just the init setup creates, so we have to delay here - * before we go into a reset in order to make the chips happy. - */ - if (p->features & AHC_ULTRA2) - mdelay(250); - else - mdelay(50); - - /* Turn off the bus reset. */ - aic_outb(p, 0, SCSISEQ); - mdelay(10); - - aic7xxx_clear_intstat(p); - /* Re-enable reset interrupts. */ - aic_outb(p, aic_inb(p, SIMODE1) | ENSCSIRST, SIMODE1); - -} - -/*+F************************************************************************* - * Function: - * aic7xxx_reset_channel - * - * Description: - * Reset the channel. - *-F*************************************************************************/ -static void -aic7xxx_reset_channel(struct aic7xxx_host *p, int channel, int initiate_reset) -{ - unsigned long offset_min, offset_max; - unsigned char sblkctl; - int cur_channel; - - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - printk(INFO_LEAD "Reset channel called, %s initiate reset.\n", - p->host_no, channel, -1, -1, (initiate_reset==TRUE) ? "will" : "won't" ); - - - if (channel == 1) - { - offset_min = 8; - offset_max = 16; - } - else - { - if (p->features & AHC_TWIN) - { - /* Channel A */ - offset_min = 0; - offset_max = 8; - } - else - { - offset_min = 0; - if (p->features & AHC_WIDE) - { - offset_max = 16; - } - else - { - offset_max = 8; - } - } - } - - while (offset_min < offset_max) - { - /* - * Revert to async/narrow transfers until we renegotiate. - */ - aic_outb(p, 0, TARG_SCSIRATE + offset_min); - if (p->features & AHC_ULTRA2) - { - aic_outb(p, 0, TARG_OFFSET + offset_min); - } - offset_min++; - } - - /* - * Reset the bus and unpause/restart the controller - */ - sblkctl = aic_inb(p, SBLKCTL); - if ( (p->chip & AHC_CHIPID_MASK) == AHC_AIC7770 ) - cur_channel = (sblkctl & SELBUSB) >> 3; - else - cur_channel = 0; - if ( (cur_channel != channel) && (p->features & AHC_TWIN) ) - { - /* - * Case 1: Command for another bus is active - */ - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - printk(INFO_LEAD "Stealthily resetting idle channel.\n", p->host_no, - channel, -1, -1); - /* - * Stealthily reset the other bus without upsetting the current bus. - */ - aic_outb(p, sblkctl ^ SELBUSB, SBLKCTL); - aic_outb(p, aic_inb(p, SIMODE1) & ~ENBUSFREE, SIMODE1); - if (initiate_reset) - { - aic7xxx_reset_current_bus(p); - } - aic_outb(p, aic_inb(p, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP), SCSISEQ); - aic7xxx_clear_intstat(p); - aic_outb(p, sblkctl, SBLKCTL); - } - else - { - /* - * Case 2: A command from this bus is active or we're idle. - */ - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - printk(INFO_LEAD "Resetting currently active channel.\n", p->host_no, - channel, -1, -1); - aic_outb(p, aic_inb(p, SIMODE1) & ~(ENBUSFREE|ENREQINIT), - SIMODE1); - p->flags &= ~AHC_HANDLING_REQINITS; - p->msg_type = MSG_TYPE_NONE; - p->msg_len = 0; - if (initiate_reset) - { - aic7xxx_reset_current_bus(p); - } - aic_outb(p, aic_inb(p, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP), SCSISEQ); - aic7xxx_clear_intstat(p); - } - if (aic7xxx_verbose & VERBOSE_RESET_RETURN) - printk(INFO_LEAD "Channel reset\n", p->host_no, channel, -1, -1); - /* - * Clean up all the state information for the pending transactions - * on this bus. - */ - aic7xxx_reset_device(p, ALL_TARGETS, channel, ALL_LUNS, SCB_LIST_NULL); - - if ( !(p->features & AHC_TWIN) ) - { - restart_sequencer(p); - } - - return; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_run_waiting_queues - * - * Description: - * Scan the awaiting_scbs queue downloading and starting as many - * scbs as we can. - *-F*************************************************************************/ -static void -aic7xxx_run_waiting_queues(struct aic7xxx_host *p) -{ - struct aic7xxx_scb *scb; - struct aic_dev_data *aic_dev; - int sent; - - - if (p->waiting_scbs.head == NULL) - return; - - sent = 0; - - /* - * First handle SCBs that are waiting but have been assigned a slot. - */ - while ((scb = scbq_remove_head(&p->waiting_scbs)) != NULL) - { - aic_dev = scb->cmd->device->hostdata; - if ( !scb->tag_action ) - { - aic_dev->temp_q_depth = 1; - } - if ( aic_dev->active_cmds >= aic_dev->temp_q_depth) - { - scbq_insert_tail(&aic_dev->delayed_scbs, scb); - } - else - { - scb->flags &= ~SCB_WAITINGQ; - aic_dev->active_cmds++; - p->activescbs++; - if ( !(scb->tag_action) ) - { - aic7xxx_busy_target(p, scb); - } - p->qinfifo[p->qinfifonext++] = scb->hscb->tag; - sent++; - } - } - if (sent) - { - if (p->features & AHC_QUEUE_REGS) - aic_outb(p, p->qinfifonext, HNSCB_QOFF); - else - { - pause_sequencer(p); - aic_outb(p, p->qinfifonext, KERNEL_QINPOS); - unpause_sequencer(p, FALSE); - } - if (p->activescbs > p->max_activescbs) - p->max_activescbs = p->activescbs; - } -} - -#ifdef CONFIG_PCI - -#define DPE 0x80 -#define SSE 0x40 -#define RMA 0x20 -#define RTA 0x10 -#define STA 0x08 -#define DPR 0x01 - -/*+F************************************************************************* - * Function: - * aic7xxx_pci_intr - * - * Description: - * Check the scsi card for PCI errors and clear the interrupt - * - * NOTE: If you don't have this function and a 2940 card encounters - * a PCI error condition, the machine will end up locked as the - * interrupt handler gets slammed with non-stop PCI error interrupts - *-F*************************************************************************/ -static void -aic7xxx_pci_intr(struct aic7xxx_host *p) -{ - unsigned char status1; - - pci_read_config_byte(p->pdev, PCI_STATUS + 1, &status1); - - if ( (status1 & DPE) && (aic7xxx_verbose & VERBOSE_MINOR_ERROR) ) - printk(WARN_LEAD "Data Parity Error during PCI address or PCI write" - "phase.\n", p->host_no, -1, -1, -1); - if ( (status1 & SSE) && (aic7xxx_verbose & VERBOSE_MINOR_ERROR) ) - printk(WARN_LEAD "Signal System Error Detected\n", p->host_no, - -1, -1, -1); - if ( (status1 & RMA) && (aic7xxx_verbose & VERBOSE_MINOR_ERROR) ) - printk(WARN_LEAD "Received a PCI Master Abort\n", p->host_no, - -1, -1, -1); - if ( (status1 & RTA) && (aic7xxx_verbose & VERBOSE_MINOR_ERROR) ) - printk(WARN_LEAD "Received a PCI Target Abort\n", p->host_no, - -1, -1, -1); - if ( (status1 & STA) && (aic7xxx_verbose & VERBOSE_MINOR_ERROR) ) - printk(WARN_LEAD "Signaled a PCI Target Abort\n", p->host_no, - -1, -1, -1); - if ( (status1 & DPR) && (aic7xxx_verbose & VERBOSE_MINOR_ERROR) ) - printk(WARN_LEAD "Data Parity Error has been reported via PCI pin " - "PERR#\n", p->host_no, -1, -1, -1); - - pci_write_config_byte(p->pdev, PCI_STATUS + 1, status1); - if (status1 & (DPR|RMA|RTA)) - aic_outb(p, CLRPARERR, CLRINT); - - if ( (aic7xxx_panic_on_abort) && (p->spurious_int > 500) ) - aic7xxx_panic_abort(p, NULL); - -} -#endif /* CONFIG_PCI */ - -/*+F************************************************************************* - * Function: - * aic7xxx_construct_ppr - * - * Description: - * Build up a Parallel Protocol Request message for use with SCSI-3 - * devices. - *-F*************************************************************************/ -static void -aic7xxx_construct_ppr(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - p->msg_buf[p->msg_index++] = MSG_EXTENDED; - p->msg_buf[p->msg_index++] = MSG_EXT_PPR_LEN; - p->msg_buf[p->msg_index++] = MSG_EXT_PPR; - p->msg_buf[p->msg_index++] = AIC_DEV(scb->cmd)->goal.period; - p->msg_buf[p->msg_index++] = 0; - p->msg_buf[p->msg_index++] = AIC_DEV(scb->cmd)->goal.offset; - p->msg_buf[p->msg_index++] = AIC_DEV(scb->cmd)->goal.width; - p->msg_buf[p->msg_index++] = AIC_DEV(scb->cmd)->goal.options; - p->msg_len += 8; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_construct_sdtr - * - * Description: - * Constucts a synchronous data transfer message in the message - * buffer on the sequencer. - *-F*************************************************************************/ -static void -aic7xxx_construct_sdtr(struct aic7xxx_host *p, unsigned char period, - unsigned char offset) -{ - p->msg_buf[p->msg_index++] = MSG_EXTENDED; - p->msg_buf[p->msg_index++] = MSG_EXT_SDTR_LEN; - p->msg_buf[p->msg_index++] = MSG_EXT_SDTR; - p->msg_buf[p->msg_index++] = period; - p->msg_buf[p->msg_index++] = offset; - p->msg_len += 5; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_construct_wdtr - * - * Description: - * Constucts a wide data transfer message in the message buffer - * on the sequencer. - *-F*************************************************************************/ -static void -aic7xxx_construct_wdtr(struct aic7xxx_host *p, unsigned char bus_width) -{ - p->msg_buf[p->msg_index++] = MSG_EXTENDED; - p->msg_buf[p->msg_index++] = MSG_EXT_WDTR_LEN; - p->msg_buf[p->msg_index++] = MSG_EXT_WDTR; - p->msg_buf[p->msg_index++] = bus_width; - p->msg_len += 4; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_calc_residual - * - * Description: - * Calculate the residual data not yet transferred. - *-F*************************************************************************/ -static void -aic7xxx_calculate_residual (struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - struct aic7xxx_hwscb *hscb; - struct scsi_cmnd *cmd; - int actual, i; - - cmd = scb->cmd; - hscb = scb->hscb; - - /* - * Don't destroy valid residual information with - * residual coming from a check sense operation. - */ - if (((scb->hscb->control & DISCONNECTED) == 0) && - (scb->flags & SCB_SENSE) == 0) - { - /* - * We had an underflow. At this time, there's only - * one other driver that bothers to check for this, - * and cmd->underflow seems to be set rather half- - * heartedly in the higher-level SCSI code. - */ - actual = scb->sg_length; - for (i=1; i < hscb->residual_SG_segment_count; i++) - { - actual -= scb->sg_list[scb->sg_count - i].length; - } - actual -= (hscb->residual_data_count[2] << 16) | - (hscb->residual_data_count[1] << 8) | - hscb->residual_data_count[0]; - - if (actual < cmd->underflow) - { - if (aic7xxx_verbose & VERBOSE_MINOR_ERROR) - { - printk(INFO_LEAD "Underflow - Wanted %u, %s %u, residual SG " - "count %d.\n", p->host_no, CTL_OF_SCB(scb), cmd->underflow, - (rq_data_dir(cmd->request) == WRITE) ? "wrote" : "read", actual, - hscb->residual_SG_segment_count); - printk(INFO_LEAD "status 0x%x.\n", p->host_no, CTL_OF_SCB(scb), - hscb->target_status); - } - /* - * In 2.4, only send back the residual information, don't flag this - * as an error. Before 2.4 we had to flag this as an error because - * the mid layer didn't check residual data counts to see if the - * command needs retried. - */ - scsi_set_resid(cmd, scb->sg_length - actual); - aic7xxx_status(cmd) = hscb->target_status; - } - } - - /* - * Clean out the residual information in the SCB for the - * next consumer. - */ - hscb->residual_data_count[2] = 0; - hscb->residual_data_count[1] = 0; - hscb->residual_data_count[0] = 0; - hscb->residual_SG_segment_count = 0; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_handle_device_reset - * - * Description: - * Interrupt handler for sequencer interrupts (SEQINT). - *-F*************************************************************************/ -static void -aic7xxx_handle_device_reset(struct aic7xxx_host *p, int target, int channel) -{ - unsigned char tindex = target; - - tindex |= ((channel & 0x01) << 3); - - /* - * Go back to async/narrow transfers and renegotiate. - */ - aic_outb(p, 0, TARG_SCSIRATE + tindex); - if (p->features & AHC_ULTRA2) - aic_outb(p, 0, TARG_OFFSET + tindex); - aic7xxx_reset_device(p, target, channel, ALL_LUNS, SCB_LIST_NULL); - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - printk(INFO_LEAD "Bus Device Reset delivered.\n", p->host_no, channel, - target, -1); - aic7xxx_run_done_queue(p, /*complete*/ TRUE); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_handle_seqint - * - * Description: - * Interrupt handler for sequencer interrupts (SEQINT). - *-F*************************************************************************/ -static void -aic7xxx_handle_seqint(struct aic7xxx_host *p, unsigned char intstat) -{ - struct aic7xxx_scb *scb; - struct aic_dev_data *aic_dev; - unsigned short target_mask; - unsigned char target, lun, tindex; - unsigned char queue_flag = FALSE; - char channel; - int result; - - target = ((aic_inb(p, SAVED_TCL) >> 4) & 0x0f); - if ( (p->chip & AHC_CHIPID_MASK) == AHC_AIC7770 ) - channel = (aic_inb(p, SBLKCTL) & SELBUSB) >> 3; - else - channel = 0; - tindex = target + (channel << 3); - lun = aic_inb(p, SAVED_TCL) & 0x07; - target_mask = (0x01 << tindex); - - /* - * Go ahead and clear the SEQINT now, that avoids any interrupt race - * conditions later on in case we enable some other interrupt. - */ - aic_outb(p, CLRSEQINT, CLRINT); - switch (intstat & SEQINT_MASK) - { - case NO_MATCH: - { - aic_outb(p, aic_inb(p, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP), - SCSISEQ); - printk(WARN_LEAD "No active SCB for reconnecting target - Issuing " - "BUS DEVICE RESET.\n", p->host_no, channel, target, lun); - printk(WARN_LEAD " SAVED_TCL=0x%x, ARG_1=0x%x, SEQADDR=0x%x\n", - p->host_no, channel, target, lun, - aic_inb(p, SAVED_TCL), aic_inb(p, ARG_1), - (aic_inb(p, SEQADDR1) << 8) | aic_inb(p, SEQADDR0)); - if (aic7xxx_panic_on_abort) - aic7xxx_panic_abort(p, NULL); - } - break; - - case SEND_REJECT: - { - if (aic7xxx_verbose & VERBOSE_MINOR_ERROR) - printk(INFO_LEAD "Rejecting unknown message (0x%x) received from " - "target, SEQ_FLAGS=0x%x\n", p->host_no, channel, target, lun, - aic_inb(p, ACCUM), aic_inb(p, SEQ_FLAGS)); - } - break; - - case NO_IDENT: - { - /* - * The reconnecting target either did not send an identify - * message, or did, but we didn't find an SCB to match and - * before it could respond to our ATN/abort, it hit a dataphase. - * The only safe thing to do is to blow it away with a bus - * reset. - */ - if (aic7xxx_verbose & (VERBOSE_SEQINT | VERBOSE_RESET_MID)) - printk(INFO_LEAD "Target did not send an IDENTIFY message; " - "LASTPHASE 0x%x, SAVED_TCL 0x%x\n", p->host_no, channel, target, - lun, aic_inb(p, LASTPHASE), aic_inb(p, SAVED_TCL)); - - aic7xxx_reset_channel(p, channel, /*initiate reset*/ TRUE); - aic7xxx_run_done_queue(p, TRUE); - - } - break; - - case BAD_PHASE: - if (aic_inb(p, LASTPHASE) == P_BUSFREE) - { - if (aic7xxx_verbose & VERBOSE_SEQINT) - printk(INFO_LEAD "Missed busfree.\n", p->host_no, channel, - target, lun); - restart_sequencer(p); - } - else - { - if (aic7xxx_verbose & VERBOSE_SEQINT) - printk(INFO_LEAD "Unknown scsi bus phase, continuing\n", p->host_no, - channel, target, lun); - } - break; - - case EXTENDED_MSG: - { - p->msg_type = MSG_TYPE_INITIATOR_MSGIN; - p->msg_len = 0; - p->msg_index = 0; - -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - printk(INFO_LEAD "Enabling REQINITs for MSG_IN\n", p->host_no, - channel, target, lun); -#endif - - /* - * To actually receive the message, simply turn on - * REQINIT interrupts and let our interrupt handler - * do the rest (REQINIT should already be true). - */ - p->flags |= AHC_HANDLING_REQINITS; - aic_outb(p, aic_inb(p, SIMODE1) | ENREQINIT, SIMODE1); - - /* - * We don't want the sequencer unpaused yet so we return early - */ - return; - } - - case REJECT_MSG: - { - /* - * What we care about here is if we had an outstanding SDTR - * or WDTR message for this target. If we did, this is a - * signal that the target is refusing negotiation. - */ - unsigned char scb_index; - unsigned char last_msg; - - scb_index = aic_inb(p, SCB_TAG); - scb = p->scb_data->scb_array[scb_index]; - aic_dev = AIC_DEV(scb->cmd); - last_msg = aic_inb(p, LAST_MSG); - - if ( (last_msg == MSG_IDENTIFYFLAG) && - (scb->tag_action) && - !(scb->flags & SCB_MSGOUT_BITS) ) - { - if (scb->tag_action == MSG_ORDERED_Q_TAG) - { - /* - * OK...the device seems able to accept tagged commands, but - * not ordered tag commands, only simple tag commands. So, we - * disable ordered tag commands and go on with life just like - * normal. - */ - scsi_adjust_queue_depth(scb->cmd->device, MSG_SIMPLE_TAG, - scb->cmd->device->queue_depth); - scb->tag_action = MSG_SIMPLE_Q_TAG; - scb->hscb->control &= ~SCB_TAG_TYPE; - scb->hscb->control |= MSG_SIMPLE_Q_TAG; - aic_outb(p, scb->hscb->control, SCB_CONTROL); - /* - * OK..we set the tag type to simple tag command, now we re-assert - * ATNO and hope this will take us into the identify phase again - * so we can resend the tag type and info to the device. - */ - aic_outb(p, MSG_IDENTIFYFLAG, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGI) | ATNO, SCSISIGO); - } - else if (scb->tag_action == MSG_SIMPLE_Q_TAG) - { - unsigned char i; - struct aic7xxx_scb *scbp; - int old_verbose; - /* - * Hmmmm....the device is flaking out on tagged commands. - */ - scsi_adjust_queue_depth(scb->cmd->device, 0 /* untagged */, - p->host->cmd_per_lun); - aic_dev->max_q_depth = aic_dev->temp_q_depth = 1; - /* - * We set this command up as a bus device reset. However, we have - * to clear the tag type as it's causing us problems. We shouldn't - * have to worry about any other commands being active, since if - * the device is refusing tagged commands, this should be the - * first tagged command sent to the device, however, we do have - * to worry about any other tagged commands that may already be - * in the qinfifo. The easiest way to do this, is to issue a BDR, - * send all the commands back to the mid level code, then let them - * come back and get rebuilt as untagged commands. - */ - scb->tag_action = 0; - scb->hscb->control &= ~(TAG_ENB | SCB_TAG_TYPE); - aic_outb(p, scb->hscb->control, SCB_CONTROL); - - old_verbose = aic7xxx_verbose; - aic7xxx_verbose &= ~(VERBOSE_RESET|VERBOSE_ABORT); - for (i=0; i < p->scb_data->numscbs; i++) - { - scbp = p->scb_data->scb_array[i]; - if ((scbp->flags & SCB_ACTIVE) && (scbp != scb)) - { - if (aic7xxx_match_scb(p, scbp, target, channel, lun, i)) - { - aic7xxx_reset_device(p, target, channel, lun, i); - } - } - } - aic7xxx_run_done_queue(p, TRUE); - aic7xxx_verbose = old_verbose; - /* - * Wait until after the for loop to set the busy index since - * aic7xxx_reset_device will clear the busy index during its - * operation. - */ - aic7xxx_busy_target(p, scb); - printk(INFO_LEAD "Device is refusing tagged commands, using " - "untagged I/O.\n", p->host_no, channel, target, lun); - aic_outb(p, MSG_IDENTIFYFLAG, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGI) | ATNO, SCSISIGO); - } - } - else if (scb->flags & SCB_MSGOUT_PPR) - { - /* - * As per the draft specs, any device capable of supporting any of - * the option values other than 0 are not allowed to reject the - * PPR message. Instead, they must negotiate out what they do - * support instead of rejecting our offering or else they cause - * a parity error during msg_out phase to signal that they don't - * like our settings. - */ - aic_dev->needppr = aic_dev->needppr_copy = 0; - aic7xxx_set_width(p, target, channel, lun, MSG_EXT_WDTR_BUS_8_BIT, - (AHC_TRANS_ACTIVE|AHC_TRANS_CUR|AHC_TRANS_QUITE), aic_dev); - aic7xxx_set_syncrate(p, NULL, target, channel, 0, 0, 0, - AHC_TRANS_ACTIVE|AHC_TRANS_CUR|AHC_TRANS_QUITE, - aic_dev); - aic_dev->goal.options = aic_dev->dtr_pending = 0; - scb->flags &= ~SCB_MSGOUT_BITS; - if(aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Device is rejecting PPR messages, falling " - "back.\n", p->host_no, channel, target, lun); - } - if ( aic_dev->goal.width ) - { - aic_dev->needwdtr = aic_dev->needwdtr_copy = 1; - aic_dev->dtr_pending = 1; - scb->flags |= SCB_MSGOUT_WDTR; - } - if ( aic_dev->goal.offset ) - { - aic_dev->needsdtr = aic_dev->needsdtr_copy = 1; - if( !aic_dev->dtr_pending ) - { - aic_dev->dtr_pending = 1; - scb->flags |= SCB_MSGOUT_SDTR; - } - } - if ( aic_dev->dtr_pending ) - { - aic_outb(p, HOST_MSG, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGI) | ATNO, SCSISIGO); - } - } - else if (scb->flags & SCB_MSGOUT_WDTR) - { - /* - * note 8bit xfers and clear flag - */ - aic_dev->needwdtr = aic_dev->needwdtr_copy = 0; - scb->flags &= ~SCB_MSGOUT_BITS; - aic7xxx_set_width(p, target, channel, lun, MSG_EXT_WDTR_BUS_8_BIT, - (AHC_TRANS_ACTIVE|AHC_TRANS_GOAL|AHC_TRANS_CUR), aic_dev); - aic7xxx_set_syncrate(p, NULL, target, channel, 0, 0, 0, - AHC_TRANS_ACTIVE|AHC_TRANS_CUR|AHC_TRANS_QUITE, - aic_dev); - if(aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Device is rejecting WDTR messages, using " - "narrow transfers.\n", p->host_no, channel, target, lun); - } - aic_dev->needsdtr = aic_dev->needsdtr_copy; - } - else if (scb->flags & SCB_MSGOUT_SDTR) - { - /* - * note asynch xfers and clear flag - */ - aic_dev->needsdtr = aic_dev->needsdtr_copy = 0; - scb->flags &= ~SCB_MSGOUT_BITS; - aic7xxx_set_syncrate(p, NULL, target, channel, 0, 0, 0, - (AHC_TRANS_CUR|AHC_TRANS_ACTIVE|AHC_TRANS_GOAL), aic_dev); - if(aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Device is rejecting SDTR messages, using " - "async transfers.\n", p->host_no, channel, target, lun); - } - } - else if (aic7xxx_verbose & VERBOSE_SEQINT) - { - /* - * Otherwise, we ignore it. - */ - printk(INFO_LEAD "Received MESSAGE_REJECT for unknown cause. " - "Ignoring.\n", p->host_no, channel, target, lun); - } - } - break; - - case BAD_STATUS: - { - unsigned char scb_index; - struct aic7xxx_hwscb *hscb; - struct scsi_cmnd *cmd; - - /* The sequencer will notify us when a command has an error that - * would be of interest to the kernel. This allows us to leave - * the sequencer running in the common case of command completes - * without error. The sequencer will have DMA'd the SCB back - * up to us, so we can reference the drivers SCB array. - * - * Set the default return value to 0 indicating not to send - * sense. The sense code will change this if needed and this - * reduces code duplication. - */ - aic_outb(p, 0, RETURN_1); - scb_index = aic_inb(p, SCB_TAG); - if (scb_index > p->scb_data->numscbs) - { - printk(WARN_LEAD "Invalid SCB during SEQINT 0x%02x, SCB_TAG %d.\n", - p->host_no, channel, target, lun, intstat, scb_index); - break; - } - scb = p->scb_data->scb_array[scb_index]; - hscb = scb->hscb; - - if (!(scb->flags & SCB_ACTIVE) || (scb->cmd == NULL)) - { - printk(WARN_LEAD "Invalid SCB during SEQINT 0x%x, scb %d, flags 0x%x," - " cmd 0x%lx.\n", p->host_no, channel, target, lun, intstat, - scb_index, scb->flags, (unsigned long) scb->cmd); - } - else - { - cmd = scb->cmd; - aic_dev = AIC_DEV(scb->cmd); - hscb->target_status = aic_inb(p, SCB_TARGET_STATUS); - aic7xxx_status(cmd) = hscb->target_status; - - cmd->result = hscb->target_status; - - switch (status_byte(hscb->target_status)) - { - case GOOD: - if (aic7xxx_verbose & VERBOSE_SEQINT) - printk(INFO_LEAD "Interrupted for status of GOOD???\n", - p->host_no, CTL_OF_SCB(scb)); - break; - - case COMMAND_TERMINATED: - case CHECK_CONDITION: - if ( !(scb->flags & SCB_SENSE) ) - { - /* - * Send a sense command to the requesting target. - * XXX - revisit this and get rid of the memcopys. - */ - memcpy(scb->sense_cmd, &generic_sense[0], - sizeof(generic_sense)); - - scb->sense_cmd[1] = (cmd->device->lun << 5); - scb->sense_cmd[4] = SCSI_SENSE_BUFFERSIZE; - - scb->sg_list[0].length = - cpu_to_le32(SCSI_SENSE_BUFFERSIZE); - scb->sg_list[0].address = - cpu_to_le32(pci_map_single(p->pdev, cmd->sense_buffer, - SCSI_SENSE_BUFFERSIZE, - PCI_DMA_FROMDEVICE)); - - /* - * XXX - We should allow disconnection, but can't as it - * might allow overlapped tagged commands. - */ - /* hscb->control &= DISCENB; */ - hscb->control = 0; - hscb->target_status = 0; - hscb->SG_list_pointer = - cpu_to_le32(SCB_DMA_ADDR(scb, scb->sg_list)); - hscb->SCSI_cmd_pointer = - cpu_to_le32(SCB_DMA_ADDR(scb, scb->sense_cmd)); - hscb->data_count = scb->sg_list[0].length; - hscb->data_pointer = scb->sg_list[0].address; - hscb->SCSI_cmd_length = COMMAND_SIZE(scb->sense_cmd[0]); - hscb->residual_SG_segment_count = 0; - hscb->residual_data_count[0] = 0; - hscb->residual_data_count[1] = 0; - hscb->residual_data_count[2] = 0; - - scb->sg_count = hscb->SG_segment_count = 1; - scb->sg_length = SCSI_SENSE_BUFFERSIZE; - scb->tag_action = 0; - scb->flags |= SCB_SENSE; - /* - * Ensure the target is busy since this will be an - * an untagged request. - */ -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - if (scb->flags & SCB_MSGOUT_BITS) - printk(INFO_LEAD "Requesting SENSE with %s\n", p->host_no, - CTL_OF_SCB(scb), (scb->flags & SCB_MSGOUT_SDTR) ? - "SDTR" : "WDTR"); - else - printk(INFO_LEAD "Requesting SENSE, no MSG\n", p->host_no, - CTL_OF_SCB(scb)); - } -#endif - aic7xxx_busy_target(p, scb); - aic_outb(p, SEND_SENSE, RETURN_1); - aic7xxx_error(cmd) = DID_OK; - break; - } /* first time sense, no errors */ - printk(INFO_LEAD "CHECK_CONDITION on REQUEST_SENSE, returning " - "an error.\n", p->host_no, CTL_OF_SCB(scb)); - aic7xxx_error(cmd) = DID_ERROR; - scb->flags &= ~SCB_SENSE; - break; - - case QUEUE_FULL: - queue_flag = TRUE; /* Mark that this is a QUEUE_FULL and */ - case BUSY: /* drop through to here */ - { - struct aic7xxx_scb *next_scbp, *prev_scbp; - unsigned char active_hscb, next_hscb, prev_hscb, scb_index; - /* - * We have to look three places for queued commands: - * 1: p->waiting_scbs queue - * 2: QINFIFO - * 3: WAITING_SCBS list on card (for commands that are started - * but haven't yet made it to the device) - * - * Of special note here is that commands on 2 or 3 above will - * have already been marked as active, while commands on 1 will - * not. The aic7xxx_done() function will want to unmark them - * from active, so any commands we pull off of 1 need to - * up the active count. - */ - next_scbp = p->waiting_scbs.head; - while ( next_scbp != NULL ) - { - prev_scbp = next_scbp; - next_scbp = next_scbp->q_next; - if ( aic7xxx_match_scb(p, prev_scbp, target, channel, lun, - SCB_LIST_NULL) ) - { - scbq_remove(&p->waiting_scbs, prev_scbp); - scb->flags = SCB_QUEUED_FOR_DONE | SCB_QUEUE_FULL; - p->activescbs++; - aic_dev->active_cmds++; - } - } - aic7xxx_search_qinfifo(p, target, channel, lun, - SCB_LIST_NULL, SCB_QUEUED_FOR_DONE | SCB_QUEUE_FULL, - FALSE, NULL); - next_scbp = NULL; - active_hscb = aic_inb(p, SCBPTR); - prev_hscb = next_hscb = scb_index = SCB_LIST_NULL; - next_hscb = aic_inb(p, WAITING_SCBH); - while (next_hscb != SCB_LIST_NULL) - { - aic_outb(p, next_hscb, SCBPTR); - scb_index = aic_inb(p, SCB_TAG); - if (scb_index < p->scb_data->numscbs) - { - next_scbp = p->scb_data->scb_array[scb_index]; - if (aic7xxx_match_scb(p, next_scbp, target, channel, lun, - SCB_LIST_NULL) ) - { - next_scbp->flags = SCB_QUEUED_FOR_DONE | SCB_QUEUE_FULL; - next_hscb = aic_inb(p, SCB_NEXT); - aic_outb(p, 0, SCB_CONTROL); - aic_outb(p, SCB_LIST_NULL, SCB_TAG); - aic7xxx_add_curscb_to_free_list(p); - if (prev_hscb == SCB_LIST_NULL) - { - /* We were first on the list, - * so we kill the selection - * hardware. Let the sequencer - * re-init the hardware itself - */ - aic_outb(p, aic_inb(p, SCSISEQ) & ~ENSELO, SCSISEQ); - aic_outb(p, CLRSELTIMEO, CLRSINT1); - aic_outb(p, next_hscb, WAITING_SCBH); - } - else - { - aic_outb(p, prev_hscb, SCBPTR); - aic_outb(p, next_hscb, SCB_NEXT); - } - } - else - { - prev_hscb = next_hscb; - next_hscb = aic_inb(p, SCB_NEXT); - } - } /* scb_index >= p->scb_data->numscbs */ - } - aic_outb(p, active_hscb, SCBPTR); - aic7xxx_run_done_queue(p, FALSE); - -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if( (aic7xxx_verbose & VERBOSE_MINOR_ERROR) || - (aic7xxx_verbose > 0xffff) ) - { - if (queue_flag) - printk(INFO_LEAD "Queue full received; queue depth %d, " - "active %d\n", p->host_no, CTL_OF_SCB(scb), - aic_dev->max_q_depth, aic_dev->active_cmds); - else - printk(INFO_LEAD "Target busy\n", p->host_no, CTL_OF_SCB(scb)); - } -#endif - if (queue_flag) - { - int diff; - result = scsi_track_queue_full(cmd->device, - aic_dev->active_cmds); - if ( result < 0 ) - { - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - printk(INFO_LEAD "Tagged Command Queueing disabled.\n", - p->host_no, CTL_OF_SCB(scb)); - diff = aic_dev->max_q_depth - p->host->cmd_per_lun; - aic_dev->temp_q_depth = 1; - aic_dev->max_q_depth = 1; - } - else if ( result > 0 ) - { - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - printk(INFO_LEAD "Queue depth reduced to %d\n", p->host_no, - CTL_OF_SCB(scb), result); - diff = aic_dev->max_q_depth - result; - aic_dev->max_q_depth = result; - /* temp_q_depth could have been dropped to 1 for an untagged - * command that might be coming up */ - if(aic_dev->temp_q_depth > result) - aic_dev->temp_q_depth = result; - } - /* We should free up the no unused SCB entries. But, that's - * a difficult thing to do because we use a direct indexed - * array, so we can't just take any entries and free them, - * we *have* to free the ones at the end of the array, and - * they very well could be in use right now, which means - * in order to do this right, we have to add a delayed - * freeing mechanism tied into the scb_free() code area. - * We'll add that later. - */ - } - break; - } - - default: - if (aic7xxx_verbose & VERBOSE_SEQINT) - printk(INFO_LEAD "Unexpected target status 0x%x.\n", p->host_no, - CTL_OF_SCB(scb), scb->hscb->target_status); - if (!aic7xxx_error(cmd)) - { - aic7xxx_error(cmd) = DID_RETRY_COMMAND; - } - break; - } /* end switch */ - } /* end else of */ - } - break; - - case AWAITING_MSG: - { - unsigned char scb_index, msg_out; - - scb_index = aic_inb(p, SCB_TAG); - msg_out = aic_inb(p, MSG_OUT); - scb = p->scb_data->scb_array[scb_index]; - aic_dev = AIC_DEV(scb->cmd); - p->msg_index = p->msg_len = 0; - /* - * This SCB had a MK_MESSAGE set in its control byte informing - * the sequencer that we wanted to send a special message to - * this target. - */ - - if ( !(scb->flags & SCB_DEVICE_RESET) && - (msg_out == MSG_IDENTIFYFLAG) && - (scb->hscb->control & TAG_ENB) ) - { - p->msg_buf[p->msg_index++] = scb->tag_action; - p->msg_buf[p->msg_index++] = scb->hscb->tag; - p->msg_len += 2; - } - - if (scb->flags & SCB_DEVICE_RESET) - { - p->msg_buf[p->msg_index++] = MSG_BUS_DEV_RESET; - p->msg_len++; - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - printk(INFO_LEAD "Bus device reset mailed.\n", - p->host_no, CTL_OF_SCB(scb)); - } - else if (scb->flags & SCB_ABORT) - { - if (scb->tag_action) - { - p->msg_buf[p->msg_index++] = MSG_ABORT_TAG; - } - else - { - p->msg_buf[p->msg_index++] = MSG_ABORT; - } - p->msg_len++; - if (aic7xxx_verbose & VERBOSE_ABORT_PROCESS) - printk(INFO_LEAD "Abort message mailed.\n", p->host_no, - CTL_OF_SCB(scb)); - } - else if (scb->flags & SCB_MSGOUT_PPR) - { - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Sending PPR (%d/%d/%d/%d) message.\n", - p->host_no, CTL_OF_SCB(scb), - aic_dev->goal.period, - aic_dev->goal.offset, - aic_dev->goal.width, - aic_dev->goal.options); - } - aic7xxx_construct_ppr(p, scb); - } - else if (scb->flags & SCB_MSGOUT_WDTR) - { - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Sending WDTR message.\n", p->host_no, - CTL_OF_SCB(scb)); - } - aic7xxx_construct_wdtr(p, aic_dev->goal.width); - } - else if (scb->flags & SCB_MSGOUT_SDTR) - { - unsigned int max_sync, period; - unsigned char options = 0; - /* - * Now that the device is selected, use the bits in SBLKCTL and - * SSTAT2 to determine the max sync rate for this device. - */ - if (p->features & AHC_ULTRA2) - { - if ( (aic_inb(p, SBLKCTL) & ENAB40) && - !(aic_inb(p, SSTAT2) & EXP_ACTIVE) ) - { - max_sync = AHC_SYNCRATE_ULTRA2; - } - else - { - max_sync = AHC_SYNCRATE_ULTRA; - } - } - else if (p->features & AHC_ULTRA) - { - max_sync = AHC_SYNCRATE_ULTRA; - } - else - { - max_sync = AHC_SYNCRATE_FAST; - } - period = aic_dev->goal.period; - aic7xxx_find_syncrate(p, &period, max_sync, &options); - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Sending SDTR %d/%d message.\n", p->host_no, - CTL_OF_SCB(scb), period, - aic_dev->goal.offset); - } - aic7xxx_construct_sdtr(p, period, aic_dev->goal.offset); - } - else - { - panic("aic7xxx: AWAITING_MSG for an SCB that does " - "not have a waiting message.\n"); - } - /* - * We've set everything up to send our message, now to actually do - * so we need to enable reqinit interrupts and let the interrupt - * handler do the rest. We don't want to unpause the sequencer yet - * though so we'll return early. We also have to make sure that - * we clear the SEQINT *BEFORE* we set the REQINIT handler active - * or else it's possible on VLB cards to lose the first REQINIT - * interrupt. Edge triggered EISA cards could also lose this - * interrupt, although PCI and level triggered cards should not - * have this problem since they continually interrupt the kernel - * until we take care of the situation. - */ - scb->flags |= SCB_MSGOUT_SENT; - p->msg_index = 0; - p->msg_type = MSG_TYPE_INITIATOR_MSGOUT; - p->flags |= AHC_HANDLING_REQINITS; - aic_outb(p, aic_inb(p, SIMODE1) | ENREQINIT, SIMODE1); - return; - } - break; - - case DATA_OVERRUN: - { - unsigned char scb_index = aic_inb(p, SCB_TAG); - unsigned char lastphase = aic_inb(p, LASTPHASE); - unsigned int i; - - scb = (p->scb_data->scb_array[scb_index]); - /* - * XXX - What do we really want to do on an overrun? The - * mid-level SCSI code should handle this, but for now, - * we'll just indicate that the command should retried. - * If we retrieved sense info on this target, then the - * base SENSE info should have been saved prior to the - * overrun error. In that case, we return DID_OK and let - * the mid level code pick up on the sense info. Otherwise - * we return DID_ERROR so the command will get retried. - */ - if ( !(scb->flags & SCB_SENSE) ) - { - printk(WARN_LEAD "Data overrun detected in %s phase, tag %d;\n", - p->host_no, CTL_OF_SCB(scb), - (lastphase == P_DATAIN) ? "Data-In" : "Data-Out", scb->hscb->tag); - printk(KERN_WARNING " %s seen Data Phase. Length=%d, NumSGs=%d.\n", - (aic_inb(p, SEQ_FLAGS) & DPHASE) ? "Have" : "Haven't", - scb->sg_length, scb->sg_count); - printk(KERN_WARNING " Raw SCSI Command: 0x"); - for (i = 0; i < scb->hscb->SCSI_cmd_length; i++) - { - printk("%02x ", scb->cmd->cmnd[i]); - } - printk("\n"); - if(aic7xxx_verbose > 0xffff) - { - for (i = 0; i < scb->sg_count; i++) - { - printk(KERN_WARNING " sg[%d] - Addr 0x%x : Length %d\n", - i, - le32_to_cpu(scb->sg_list[i].address), - le32_to_cpu(scb->sg_list[i].length) ); - } - } - aic7xxx_error(scb->cmd) = DID_ERROR; - } - else - printk(INFO_LEAD "Data Overrun during SEND_SENSE operation.\n", - p->host_no, CTL_OF_SCB(scb)); - } - break; - - case WIDE_RESIDUE: - { - unsigned char resid_sgcnt, index; - unsigned char scb_index = aic_inb(p, SCB_TAG); - unsigned int cur_addr, resid_dcnt; - unsigned int native_addr, native_length, sg_addr; - int i; - - if(scb_index > p->scb_data->numscbs) - { - printk(WARN_LEAD "invalid scb_index during WIDE_RESIDUE.\n", - p->host_no, -1, -1, -1); - /* - * XXX: Add error handling here - */ - break; - } - scb = p->scb_data->scb_array[scb_index]; - if(!(scb->flags & SCB_ACTIVE) || (scb->cmd == NULL)) - { - printk(WARN_LEAD "invalid scb during WIDE_RESIDUE flags:0x%x " - "scb->cmd:0x%lx\n", p->host_no, CTL_OF_SCB(scb), - scb->flags, (unsigned long)scb->cmd); - break; - } - if(aic7xxx_verbose & VERBOSE_MINOR_ERROR) - printk(INFO_LEAD "Got WIDE_RESIDUE message, patching up data " - "pointer.\n", p->host_no, CTL_OF_SCB(scb)); - - /* - * We have a valid scb to use on this WIDE_RESIDUE message, so - * we need to walk the sg list looking for this particular sg - * segment, then see if we happen to be at the very beginning of - * the segment. If we are, then we have to back things up to - * the previous segment. If not, then we simply need to remove - * one byte from this segments address and add one to the byte - * count. - */ - cur_addr = aic_inb(p, SHADDR) | (aic_inb(p, SHADDR + 1) << 8) | - (aic_inb(p, SHADDR + 2) << 16) | (aic_inb(p, SHADDR + 3) << 24); - sg_addr = aic_inb(p, SG_COUNT + 1) | (aic_inb(p, SG_COUNT + 2) << 8) | - (aic_inb(p, SG_COUNT + 3) << 16) | (aic_inb(p, SG_COUNT + 4) << 24); - resid_sgcnt = aic_inb(p, SCB_RESID_SGCNT); - resid_dcnt = aic_inb(p, SCB_RESID_DCNT) | - (aic_inb(p, SCB_RESID_DCNT + 1) << 8) | - (aic_inb(p, SCB_RESID_DCNT + 2) << 16); - index = scb->sg_count - ((resid_sgcnt) ? resid_sgcnt : 1); - native_addr = le32_to_cpu(scb->sg_list[index].address); - native_length = le32_to_cpu(scb->sg_list[index].length); - /* - * If resid_dcnt == native_length, then we just loaded this SG - * segment and we need to back it up one... - */ - if(resid_dcnt == native_length) - { - if(index == 0) - { - /* - * Oops, this isn't right, we can't back up to before the - * beginning. This must be a bogus message, ignore it. - */ - break; - } - resid_dcnt = 1; - resid_sgcnt += 1; - native_addr = le32_to_cpu(scb->sg_list[index - 1].address); - native_length = le32_to_cpu(scb->sg_list[index - 1].length); - cur_addr = native_addr + (native_length - 1); - sg_addr -= sizeof(struct hw_scatterlist); - } - else - { - /* - * resid_dcnt != native_length, so we are in the middle of a SG - * element. Back it up one byte and leave the rest alone. - */ - resid_dcnt += 1; - cur_addr -= 1; - } - - /* - * Output the new addresses and counts to the right places on the - * card. - */ - aic_outb(p, resid_sgcnt, SG_COUNT); - aic_outb(p, resid_sgcnt, SCB_RESID_SGCNT); - aic_outb(p, sg_addr & 0xff, SG_COUNT + 1); - aic_outb(p, (sg_addr >> 8) & 0xff, SG_COUNT + 2); - aic_outb(p, (sg_addr >> 16) & 0xff, SG_COUNT + 3); - aic_outb(p, (sg_addr >> 24) & 0xff, SG_COUNT + 4); - aic_outb(p, resid_dcnt & 0xff, SCB_RESID_DCNT); - aic_outb(p, (resid_dcnt >> 8) & 0xff, SCB_RESID_DCNT + 1); - aic_outb(p, (resid_dcnt >> 16) & 0xff, SCB_RESID_DCNT + 2); - - /* - * The sequencer actually wants to find the new address - * in the SHADDR register set. On the Ultra2 and later controllers - * this register set is readonly. In order to get the right number - * into the register, you actually have to enter it in HADDR and then - * use the PRELOADEN bit of DFCNTRL to drop it through from the - * HADDR register to the SHADDR register. On non-Ultra2 controllers, - * we simply write it direct. - */ - if(p->features & AHC_ULTRA2) - { - /* - * We might as well be accurate and drop both the resid_dcnt and - * cur_addr into HCNT and HADDR and have both of them drop - * through to the shadow layer together. - */ - aic_outb(p, resid_dcnt & 0xff, HCNT); - aic_outb(p, (resid_dcnt >> 8) & 0xff, HCNT + 1); - aic_outb(p, (resid_dcnt >> 16) & 0xff, HCNT + 2); - aic_outb(p, cur_addr & 0xff, HADDR); - aic_outb(p, (cur_addr >> 8) & 0xff, HADDR + 1); - aic_outb(p, (cur_addr >> 16) & 0xff, HADDR + 2); - aic_outb(p, (cur_addr >> 24) & 0xff, HADDR + 3); - aic_outb(p, aic_inb(p, DMAPARAMS) | PRELOADEN, DFCNTRL); - udelay(1); - aic_outb(p, aic_inb(p, DMAPARAMS) & ~(SCSIEN|HDMAEN), DFCNTRL); - i=0; - while(((aic_inb(p, DFCNTRL) & (SCSIEN|HDMAEN)) != 0) && (i++ < 1000)) - { - udelay(1); - } - } - else - { - aic_outb(p, cur_addr & 0xff, SHADDR); - aic_outb(p, (cur_addr >> 8) & 0xff, SHADDR + 1); - aic_outb(p, (cur_addr >> 16) & 0xff, SHADDR + 2); - aic_outb(p, (cur_addr >> 24) & 0xff, SHADDR + 3); - } - } - break; - - case SEQ_SG_FIXUP: - { - unsigned char scb_index, tmp; - int sg_addr, sg_length; - - scb_index = aic_inb(p, SCB_TAG); - - if(scb_index > p->scb_data->numscbs) - { - printk(WARN_LEAD "invalid scb_index during SEQ_SG_FIXUP.\n", - p->host_no, -1, -1, -1); - printk(INFO_LEAD "SCSISIGI 0x%x, SEQADDR 0x%x, SSTAT0 0x%x, SSTAT1 " - "0x%x\n", p->host_no, -1, -1, -1, - aic_inb(p, SCSISIGI), - aic_inb(p, SEQADDR0) | (aic_inb(p, SEQADDR1) << 8), - aic_inb(p, SSTAT0), aic_inb(p, SSTAT1)); - printk(INFO_LEAD "SG_CACHEPTR 0x%x, SSTAT2 0x%x, STCNT 0x%x\n", - p->host_no, -1, -1, -1, aic_inb(p, SG_CACHEPTR), - aic_inb(p, SSTAT2), aic_inb(p, STCNT + 2) << 16 | - aic_inb(p, STCNT + 1) << 8 | aic_inb(p, STCNT)); - /* - * XXX: Add error handling here - */ - break; - } - scb = p->scb_data->scb_array[scb_index]; - if(!(scb->flags & SCB_ACTIVE) || (scb->cmd == NULL)) - { - printk(WARN_LEAD "invalid scb during SEQ_SG_FIXUP flags:0x%x " - "scb->cmd:0x%p\n", p->host_no, CTL_OF_SCB(scb), - scb->flags, scb->cmd); - printk(INFO_LEAD "SCSISIGI 0x%x, SEQADDR 0x%x, SSTAT0 0x%x, SSTAT1 " - "0x%x\n", p->host_no, CTL_OF_SCB(scb), - aic_inb(p, SCSISIGI), - aic_inb(p, SEQADDR0) | (aic_inb(p, SEQADDR1) << 8), - aic_inb(p, SSTAT0), aic_inb(p, SSTAT1)); - printk(INFO_LEAD "SG_CACHEPTR 0x%x, SSTAT2 0x%x, STCNT 0x%x\n", - p->host_no, CTL_OF_SCB(scb), aic_inb(p, SG_CACHEPTR), - aic_inb(p, SSTAT2), aic_inb(p, STCNT + 2) << 16 | - aic_inb(p, STCNT + 1) << 8 | aic_inb(p, STCNT)); - break; - } - if(aic7xxx_verbose & VERBOSE_MINOR_ERROR) - printk(INFO_LEAD "Fixing up SG address for sequencer.\n", p->host_no, - CTL_OF_SCB(scb)); - /* - * Advance the SG pointer to the next element in the list - */ - tmp = aic_inb(p, SG_NEXT); - tmp += SG_SIZEOF; - aic_outb(p, tmp, SG_NEXT); - if( tmp < SG_SIZEOF ) - aic_outb(p, aic_inb(p, SG_NEXT + 1) + 1, SG_NEXT + 1); - tmp = aic_inb(p, SG_COUNT) - 1; - aic_outb(p, tmp, SG_COUNT); - sg_addr = le32_to_cpu(scb->sg_list[scb->sg_count - tmp].address); - sg_length = le32_to_cpu(scb->sg_list[scb->sg_count - tmp].length); - /* - * Now stuff the element we just advanced past down onto the - * card so it can be stored in the residual area. - */ - aic_outb(p, sg_addr & 0xff, HADDR); - aic_outb(p, (sg_addr >> 8) & 0xff, HADDR + 1); - aic_outb(p, (sg_addr >> 16) & 0xff, HADDR + 2); - aic_outb(p, (sg_addr >> 24) & 0xff, HADDR + 3); - aic_outb(p, sg_length & 0xff, HCNT); - aic_outb(p, (sg_length >> 8) & 0xff, HCNT + 1); - aic_outb(p, (sg_length >> 16) & 0xff, HCNT + 2); - aic_outb(p, (tmp << 2) | ((tmp == 1) ? LAST_SEG : 0), SG_CACHEPTR); - aic_outb(p, aic_inb(p, DMAPARAMS), DFCNTRL); - while(aic_inb(p, SSTAT0) & SDONE) udelay(1); - while(aic_inb(p, DFCNTRL) & (HDMAEN|SCSIEN)) aic_outb(p, 0, DFCNTRL); - } - break; - -#ifdef AIC7XXX_NOT_YET - case TRACEPOINT2: - { - printk(INFO_LEAD "Tracepoint #2 reached.\n", p->host_no, - channel, target, lun); - } - break; - - /* XXX Fill these in later */ - case MSG_BUFFER_BUSY: - printk("aic7xxx: Message buffer busy.\n"); - break; - case MSGIN_PHASEMIS: - printk("aic7xxx: Message-in phasemis.\n"); - break; -#endif - - default: /* unknown */ - printk(WARN_LEAD "Unknown SEQINT, INTSTAT 0x%x, SCSISIGI 0x%x.\n", - p->host_no, channel, target, lun, intstat, - aic_inb(p, SCSISIGI)); - break; - } - - /* - * Clear the sequencer interrupt and unpause the sequencer. - */ - unpause_sequencer(p, /* unpause always */ TRUE); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_parse_msg - * - * Description: - * Parses incoming messages into actions on behalf of - * aic7xxx_handle_reqinit - *_F*************************************************************************/ -static int -aic7xxx_parse_msg(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - int reject, reply, done; - unsigned char target_scsirate, tindex; - unsigned short target_mask; - unsigned char target, channel, lun; - unsigned char bus_width, new_bus_width; - unsigned char trans_options, new_trans_options; - unsigned int period, new_period, offset, new_offset, maxsync; - struct aic7xxx_syncrate *syncrate; - struct aic_dev_data *aic_dev; - - target = scb->cmd->device->id; - channel = scb->cmd->device->channel; - lun = scb->cmd->device->lun; - reply = reject = done = FALSE; - tindex = TARGET_INDEX(scb->cmd); - aic_dev = AIC_DEV(scb->cmd); - target_scsirate = aic_inb(p, TARG_SCSIRATE + tindex); - target_mask = (0x01 << tindex); - - /* - * Parse as much of the message as is available, - * rejecting it if we don't support it. When - * the entire message is available and has been - * handled, return TRUE indicating that we have - * parsed an entire message. - */ - - if (p->msg_buf[0] != MSG_EXTENDED) - { - reject = TRUE; - } - - /* - * Even if we are an Ultra3 card, don't allow Ultra3 sync rates when - * using the SDTR messages. We need the PPR messages to enable the - * higher speeds that include things like Dual Edge clocking. - */ - if (p->features & AHC_ULTRA2) - { - if ( (aic_inb(p, SBLKCTL) & ENAB40) && - !(aic_inb(p, SSTAT2) & EXP_ACTIVE) ) - { - if (p->features & AHC_ULTRA3) - maxsync = AHC_SYNCRATE_ULTRA3; - else - maxsync = AHC_SYNCRATE_ULTRA2; - } - else - { - maxsync = AHC_SYNCRATE_ULTRA; - } - } - else if (p->features & AHC_ULTRA) - { - maxsync = AHC_SYNCRATE_ULTRA; - } - else - { - maxsync = AHC_SYNCRATE_FAST; - } - - /* - * Just accept the length byte outright and perform - * more checking once we know the message type. - */ - - if ( !reject && (p->msg_len > 2) ) - { - switch(p->msg_buf[2]) - { - case MSG_EXT_SDTR: - { - - if (p->msg_buf[1] != MSG_EXT_SDTR_LEN) - { - reject = TRUE; - break; - } - - if (p->msg_len < (MSG_EXT_SDTR_LEN + 2)) - { - break; - } - - period = new_period = p->msg_buf[3]; - offset = new_offset = p->msg_buf[4]; - trans_options = new_trans_options = 0; - bus_width = new_bus_width = target_scsirate & WIDEXFER; - - /* - * If our current max syncrate is in the Ultra3 range, bump it back - * down to Ultra2 since we can't negotiate DT transfers using SDTR - */ - if(maxsync == AHC_SYNCRATE_ULTRA3) - maxsync = AHC_SYNCRATE_ULTRA2; - - /* - * We might have a device that is starting negotiation with us - * before we can start up negotiation with it....be prepared to - * have a device ask for a higher speed then we want to give it - * in that case - */ - if ( (scb->flags & (SCB_MSGOUT_SENT|SCB_MSGOUT_SDTR)) != - (SCB_MSGOUT_SENT|SCB_MSGOUT_SDTR) ) - { - if (!(aic_dev->flags & DEVICE_DTR_SCANNED)) - { - /* - * We shouldn't get here unless this is a narrow drive, wide - * devices should trigger this same section of code in the WDTR - * handler first instead. - */ - aic_dev->goal.width = MSG_EXT_WDTR_BUS_8_BIT; - aic_dev->goal.options = 0; - if(p->user[tindex].offset) - { - aic_dev->needsdtr_copy = 1; - aic_dev->goal.period = max_t(unsigned char, 10,p->user[tindex].period); - if(p->features & AHC_ULTRA2) - { - aic_dev->goal.offset = MAX_OFFSET_ULTRA2; - } - else - { - aic_dev->goal.offset = MAX_OFFSET_8BIT; - } - } - else - { - aic_dev->needsdtr_copy = 0; - aic_dev->goal.period = 255; - aic_dev->goal.offset = 0; - } - aic_dev->flags |= DEVICE_DTR_SCANNED | DEVICE_PRINT_DTR; - } - else if (aic_dev->needsdtr_copy == 0) - { - /* - * This is a preemptive message from the target, we've already - * scanned this target and set our options for it, and we - * don't need a SDTR with this target (for whatever reason), - * so reject this incoming SDTR - */ - reject = TRUE; - break; - } - - /* The device is sending this message first and we have to reply */ - reply = TRUE; - - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Received pre-emptive SDTR message from " - "target.\n", p->host_no, CTL_OF_SCB(scb)); - } - /* - * Validate the values the device passed to us against our SEEPROM - * settings. We don't have to do this if we aren't replying since - * the device isn't allowed to send values greater than the ones - * we first sent to it. - */ - new_period = max_t(unsigned int, period, aic_dev->goal.period); - new_offset = min_t(unsigned int, offset, aic_dev->goal.offset); - } - - /* - * Use our new_period, new_offset, bus_width, and card options - * to determine the actual syncrate settings - */ - syncrate = aic7xxx_find_syncrate(p, &new_period, maxsync, - &trans_options); - aic7xxx_validate_offset(p, syncrate, &new_offset, bus_width); - - /* - * Did we drop to async? If so, send a reply regardless of whether - * or not we initiated this negotiation. - */ - if ((new_offset == 0) && (new_offset != offset)) - { - aic_dev->needsdtr_copy = 0; - reply = TRUE; - } - - /* - * Did we start this, if not, or if we went too low and had to - * go async, then send an SDTR back to the target - */ - if(reply) - { - /* when sending a reply, make sure that the goal settings are - * updated along with current and active since the code that - * will actually build the message for the sequencer uses the - * goal settings as its guidelines. - */ - aic7xxx_set_syncrate(p, syncrate, target, channel, new_period, - new_offset, trans_options, - AHC_TRANS_GOAL|AHC_TRANS_ACTIVE|AHC_TRANS_CUR, - aic_dev); - scb->flags &= ~SCB_MSGOUT_BITS; - scb->flags |= SCB_MSGOUT_SDTR; - aic_outb(p, HOST_MSG, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGO) | ATNO, SCSISIGO); - } - else - { - aic7xxx_set_syncrate(p, syncrate, target, channel, new_period, - new_offset, trans_options, - AHC_TRANS_ACTIVE|AHC_TRANS_CUR, aic_dev); - aic_dev->needsdtr = 0; - } - done = TRUE; - break; - } - case MSG_EXT_WDTR: - { - - if (p->msg_buf[1] != MSG_EXT_WDTR_LEN) - { - reject = TRUE; - break; - } - - if (p->msg_len < (MSG_EXT_WDTR_LEN + 2)) - { - break; - } - - bus_width = new_bus_width = p->msg_buf[3]; - - if ( (scb->flags & (SCB_MSGOUT_SENT|SCB_MSGOUT_WDTR)) == - (SCB_MSGOUT_SENT|SCB_MSGOUT_WDTR) ) - { - switch(bus_width) - { - default: - { - reject = TRUE; - if ( (aic7xxx_verbose & VERBOSE_NEGOTIATION2) && - ((aic_dev->flags & DEVICE_PRINT_DTR) || - (aic7xxx_verbose > 0xffff)) ) - { - printk(INFO_LEAD "Requesting %d bit transfers, rejecting.\n", - p->host_no, CTL_OF_SCB(scb), 8 * (0x01 << bus_width)); - } - } /* We fall through on purpose */ - case MSG_EXT_WDTR_BUS_8_BIT: - { - aic_dev->goal.width = MSG_EXT_WDTR_BUS_8_BIT; - aic_dev->needwdtr_copy &= ~target_mask; - break; - } - case MSG_EXT_WDTR_BUS_16_BIT: - { - break; - } - } - aic_dev->needwdtr = 0; - aic7xxx_set_width(p, target, channel, lun, new_bus_width, - AHC_TRANS_ACTIVE|AHC_TRANS_CUR, aic_dev); - } - else - { - if ( !(aic_dev->flags & DEVICE_DTR_SCANNED) ) - { - /* - * Well, we now know the WDTR and SYNC caps of this device since - * it contacted us first, mark it as such and copy the user stuff - * over to the goal stuff. - */ - if( (p->features & AHC_WIDE) && p->user[tindex].width ) - { - aic_dev->goal.width = MSG_EXT_WDTR_BUS_16_BIT; - aic_dev->needwdtr_copy = 1; - } - - /* - * Devices that support DT transfers don't start WDTR requests - */ - aic_dev->goal.options = 0; - - if(p->user[tindex].offset) - { - aic_dev->needsdtr_copy = 1; - aic_dev->goal.period = max_t(unsigned char, 10, p->user[tindex].period); - if(p->features & AHC_ULTRA2) - { - aic_dev->goal.offset = MAX_OFFSET_ULTRA2; - } - else if( aic_dev->goal.width ) - { - aic_dev->goal.offset = MAX_OFFSET_16BIT; - } - else - { - aic_dev->goal.offset = MAX_OFFSET_8BIT; - } - } else { - aic_dev->needsdtr_copy = 0; - aic_dev->goal.period = 255; - aic_dev->goal.offset = 0; - } - - aic_dev->flags |= DEVICE_DTR_SCANNED | DEVICE_PRINT_DTR; - } - else if (aic_dev->needwdtr_copy == 0) - { - /* - * This is a preemptive message from the target, we've already - * scanned this target and set our options for it, and we - * don't need a WDTR with this target (for whatever reason), - * so reject this incoming WDTR - */ - reject = TRUE; - break; - } - - /* The device is sending this message first and we have to reply */ - reply = TRUE; - - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Received pre-emptive WDTR message from " - "target.\n", p->host_no, CTL_OF_SCB(scb)); - } - switch(bus_width) - { - case MSG_EXT_WDTR_BUS_16_BIT: - { - if ( (p->features & AHC_WIDE) && - (aic_dev->goal.width == MSG_EXT_WDTR_BUS_16_BIT) ) - { - new_bus_width = MSG_EXT_WDTR_BUS_16_BIT; - break; - } - } /* Fall through if we aren't a wide card */ - default: - case MSG_EXT_WDTR_BUS_8_BIT: - { - aic_dev->needwdtr_copy = 0; - new_bus_width = MSG_EXT_WDTR_BUS_8_BIT; - break; - } - } - scb->flags &= ~SCB_MSGOUT_BITS; - scb->flags |= SCB_MSGOUT_WDTR; - aic_dev->needwdtr = 0; - if(aic_dev->dtr_pending == 0) - { - /* there is no other command with SCB_DTR_SCB already set that will - * trigger the release of the dtr_pending bit. Both set the bit - * and set scb->flags |= SCB_DTR_SCB - */ - aic_dev->dtr_pending = 1; - scb->flags |= SCB_DTR_SCB; - } - aic_outb(p, HOST_MSG, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGO) | ATNO, SCSISIGO); - /* when sending a reply, make sure that the goal settings are - * updated along with current and active since the code that - * will actually build the message for the sequencer uses the - * goal settings as its guidelines. - */ - aic7xxx_set_width(p, target, channel, lun, new_bus_width, - AHC_TRANS_GOAL|AHC_TRANS_ACTIVE|AHC_TRANS_CUR, - aic_dev); - } - - /* - * By virtue of the SCSI spec, a WDTR message negates any existing - * SDTR negotiations. So, even if needsdtr isn't marked for this - * device, we still have to do a new SDTR message if the device - * supports SDTR at all. Therefore, we check needsdtr_copy instead - * of needstr. - */ - aic7xxx_set_syncrate(p, NULL, target, channel, 0, 0, 0, - AHC_TRANS_ACTIVE|AHC_TRANS_CUR|AHC_TRANS_QUITE, - aic_dev); - aic_dev->needsdtr = aic_dev->needsdtr_copy; - done = TRUE; - break; - } - case MSG_EXT_PPR: - { - - if (p->msg_buf[1] != MSG_EXT_PPR_LEN) - { - reject = TRUE; - break; - } - - if (p->msg_len < (MSG_EXT_PPR_LEN + 2)) - { - break; - } - - period = new_period = p->msg_buf[3]; - offset = new_offset = p->msg_buf[5]; - bus_width = new_bus_width = p->msg_buf[6]; - trans_options = new_trans_options = p->msg_buf[7] & 0xf; - - if(aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Parsing PPR message (%d/%d/%d/%d)\n", - p->host_no, CTL_OF_SCB(scb), period, offset, bus_width, - trans_options); - } - - /* - * We might have a device that is starting negotiation with us - * before we can start up negotiation with it....be prepared to - * have a device ask for a higher speed then we want to give it - * in that case - */ - if ( (scb->flags & (SCB_MSGOUT_SENT|SCB_MSGOUT_PPR)) != - (SCB_MSGOUT_SENT|SCB_MSGOUT_PPR) ) - { - /* Have we scanned the device yet? */ - if (!(aic_dev->flags & DEVICE_DTR_SCANNED)) - { - /* The device is electing to use PPR messages, so we will too until - * we know better */ - aic_dev->needppr = aic_dev->needppr_copy = 1; - aic_dev->needsdtr = aic_dev->needsdtr_copy = 0; - aic_dev->needwdtr = aic_dev->needwdtr_copy = 0; - - /* We know the device is SCSI-3 compliant due to PPR */ - aic_dev->flags |= DEVICE_SCSI_3; - - /* - * Not only is the device starting this up, but it also hasn't - * been scanned yet, so this would likely be our TUR or our - * INQUIRY command at scan time, so we need to use the - * settings from the SEEPROM if they existed. Of course, even - * if we didn't find a SEEPROM, we stuffed default values into - * the user settings anyway, so use those in all cases. - */ - aic_dev->goal.width = p->user[tindex].width; - if(p->user[tindex].offset) - { - aic_dev->goal.period = p->user[tindex].period; - aic_dev->goal.options = p->user[tindex].options; - if(p->features & AHC_ULTRA2) - { - aic_dev->goal.offset = MAX_OFFSET_ULTRA2; - } - else if( aic_dev->goal.width && - (bus_width == MSG_EXT_WDTR_BUS_16_BIT) && - p->features & AHC_WIDE ) - { - aic_dev->goal.offset = MAX_OFFSET_16BIT; - } - else - { - aic_dev->goal.offset = MAX_OFFSET_8BIT; - } - } - else - { - aic_dev->goal.period = 255; - aic_dev->goal.offset = 0; - aic_dev->goal.options = 0; - } - aic_dev->flags |= DEVICE_DTR_SCANNED | DEVICE_PRINT_DTR; - } - else if (aic_dev->needppr_copy == 0) - { - /* - * This is a preemptive message from the target, we've already - * scanned this target and set our options for it, and we - * don't need a PPR with this target (for whatever reason), - * so reject this incoming PPR - */ - reject = TRUE; - break; - } - - /* The device is sending this message first and we have to reply */ - reply = TRUE; - - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Received pre-emptive PPR message from " - "target.\n", p->host_no, CTL_OF_SCB(scb)); - } - - } - - switch(bus_width) - { - case MSG_EXT_WDTR_BUS_16_BIT: - { - if ( (aic_dev->goal.width == MSG_EXT_WDTR_BUS_16_BIT) && - p->features & AHC_WIDE) - { - break; - } - } - default: - { - if ( (aic7xxx_verbose & VERBOSE_NEGOTIATION2) && - ((aic_dev->flags & DEVICE_PRINT_DTR) || - (aic7xxx_verbose > 0xffff)) ) - { - reply = TRUE; - printk(INFO_LEAD "Requesting %d bit transfers, rejecting.\n", - p->host_no, CTL_OF_SCB(scb), 8 * (0x01 << bus_width)); - } - } /* We fall through on purpose */ - case MSG_EXT_WDTR_BUS_8_BIT: - { - /* - * According to the spec, if we aren't wide, we also can't be - * Dual Edge so clear the options byte - */ - new_trans_options = 0; - new_bus_width = MSG_EXT_WDTR_BUS_8_BIT; - break; - } - } - - if(reply) - { - /* when sending a reply, make sure that the goal settings are - * updated along with current and active since the code that - * will actually build the message for the sequencer uses the - * goal settings as its guidelines. - */ - aic7xxx_set_width(p, target, channel, lun, new_bus_width, - AHC_TRANS_GOAL|AHC_TRANS_ACTIVE|AHC_TRANS_CUR, - aic_dev); - syncrate = aic7xxx_find_syncrate(p, &new_period, maxsync, - &new_trans_options); - aic7xxx_validate_offset(p, syncrate, &new_offset, new_bus_width); - aic7xxx_set_syncrate(p, syncrate, target, channel, new_period, - new_offset, new_trans_options, - AHC_TRANS_GOAL|AHC_TRANS_ACTIVE|AHC_TRANS_CUR, - aic_dev); - } - else - { - aic7xxx_set_width(p, target, channel, lun, new_bus_width, - AHC_TRANS_ACTIVE|AHC_TRANS_CUR, aic_dev); - syncrate = aic7xxx_find_syncrate(p, &new_period, maxsync, - &new_trans_options); - aic7xxx_validate_offset(p, syncrate, &new_offset, new_bus_width); - aic7xxx_set_syncrate(p, syncrate, target, channel, new_period, - new_offset, new_trans_options, - AHC_TRANS_ACTIVE|AHC_TRANS_CUR, aic_dev); - } - - /* - * As it turns out, if we don't *have* to have PPR messages, then - * configure ourselves not to use them since that makes some - * external drive chassis work (those chassis can't parse PPR - * messages and they mangle the SCSI bus until you send a WDTR - * and SDTR that they can understand). - */ - if(new_trans_options == 0) - { - aic_dev->needppr = aic_dev->needppr_copy = 0; - if(new_offset) - { - aic_dev->needsdtr = aic_dev->needsdtr_copy = 1; - } - if (new_bus_width) - { - aic_dev->needwdtr = aic_dev->needwdtr_copy = 1; - } - } - - if((new_offset == 0) && (offset != 0)) - { - /* - * Oops, the syncrate went to low for this card and we fell off - * to async (should never happen with a device that uses PPR - * messages, but have to be complete) - */ - reply = TRUE; - } - - if(reply) - { - scb->flags &= ~SCB_MSGOUT_BITS; - scb->flags |= SCB_MSGOUT_PPR; - aic_outb(p, HOST_MSG, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGO) | ATNO, SCSISIGO); - } - else - { - aic_dev->needppr = 0; - } - done = TRUE; - break; - } - default: - { - reject = TRUE; - break; - } - } /* end of switch(p->msg_type) */ - } /* end of if (!reject && (p->msg_len > 2)) */ - - if (!reply && reject) - { - aic_outb(p, MSG_MESSAGE_REJECT, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGO) | ATNO, SCSISIGO); - done = TRUE; - } - return(done); -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_handle_reqinit - * - * Description: - * Interrupt handler for REQINIT interrupts (used to transfer messages to - * and from devices). - *_F*************************************************************************/ -static void -aic7xxx_handle_reqinit(struct aic7xxx_host *p, struct aic7xxx_scb *scb) -{ - unsigned char lastbyte; - unsigned char phasemis; - int done = FALSE; - - switch(p->msg_type) - { - case MSG_TYPE_INITIATOR_MSGOUT: - { - if (p->msg_len == 0) - panic("aic7xxx: REQINIT with no active message!\n"); - - lastbyte = (p->msg_index == (p->msg_len - 1)); - phasemis = ( aic_inb(p, SCSISIGI) & PHASE_MASK) != P_MESGOUT; - - if (lastbyte || phasemis) - { - /* Time to end the message */ - p->msg_len = 0; - p->msg_type = MSG_TYPE_NONE; - /* - * NOTE-TO-MYSELF: If you clear the REQINIT after you - * disable REQINITs, then cases of REJECT_MSG stop working - * and hang the bus - */ - aic_outb(p, aic_inb(p, SIMODE1) & ~ENREQINIT, SIMODE1); - aic_outb(p, CLRSCSIINT, CLRINT); - p->flags &= ~AHC_HANDLING_REQINITS; - - if (phasemis == 0) - { - aic_outb(p, p->msg_buf[p->msg_index], SINDEX); - aic_outb(p, 0, RETURN_1); -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - printk(INFO_LEAD "Completed sending of REQINIT message.\n", - p->host_no, CTL_OF_SCB(scb)); -#endif - } - else - { - aic_outb(p, MSGOUT_PHASEMIS, RETURN_1); -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - printk(INFO_LEAD "PHASEMIS while sending REQINIT message.\n", - p->host_no, CTL_OF_SCB(scb)); -#endif - } - unpause_sequencer(p, TRUE); - } - else - { - /* - * Present the byte on the bus (clearing REQINIT) but don't - * unpause the sequencer. - */ - aic_outb(p, CLRREQINIT, CLRSINT1); - aic_outb(p, CLRSCSIINT, CLRINT); - aic_outb(p, p->msg_buf[p->msg_index++], SCSIDATL); - } - break; - } - case MSG_TYPE_INITIATOR_MSGIN: - { - phasemis = ( aic_inb(p, SCSISIGI) & PHASE_MASK ) != P_MESGIN; - - if (phasemis == 0) - { - p->msg_len++; - /* Pull the byte in without acking it */ - p->msg_buf[p->msg_index] = aic_inb(p, SCSIBUSL); - done = aic7xxx_parse_msg(p, scb); - /* Ack the byte */ - aic_outb(p, CLRREQINIT, CLRSINT1); - aic_outb(p, CLRSCSIINT, CLRINT); - aic_inb(p, SCSIDATL); - p->msg_index++; - } - if (phasemis || done) - { -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - { - if (phasemis) - printk(INFO_LEAD "PHASEMIS while receiving REQINIT message.\n", - p->host_no, CTL_OF_SCB(scb)); - else - printk(INFO_LEAD "Completed receipt of REQINIT message.\n", - p->host_no, CTL_OF_SCB(scb)); - } -#endif - /* Time to end our message session */ - p->msg_len = 0; - p->msg_type = MSG_TYPE_NONE; - aic_outb(p, aic_inb(p, SIMODE1) & ~ENREQINIT, SIMODE1); - aic_outb(p, CLRSCSIINT, CLRINT); - p->flags &= ~AHC_HANDLING_REQINITS; - unpause_sequencer(p, TRUE); - } - break; - } - default: - { - panic("aic7xxx: Unknown REQINIT message type.\n"); - break; - } - } /* End of switch(p->msg_type) */ -} - -/*+F************************************************************************* - * Function: - * aic7xxx_handle_scsiint - * - * Description: - * Interrupt handler for SCSI interrupts (SCSIINT). - *-F*************************************************************************/ -static void -aic7xxx_handle_scsiint(struct aic7xxx_host *p, unsigned char intstat) -{ - unsigned char scb_index; - unsigned char status; - struct aic7xxx_scb *scb; - struct aic_dev_data *aic_dev; - - scb_index = aic_inb(p, SCB_TAG); - status = aic_inb(p, SSTAT1); - - if (scb_index < p->scb_data->numscbs) - { - scb = p->scb_data->scb_array[scb_index]; - if ((scb->flags & SCB_ACTIVE) == 0) - { - scb = NULL; - } - } - else - { - scb = NULL; - } - - - if ((status & SCSIRSTI) != 0) - { - int channel; - - if ( (p->chip & AHC_CHIPID_MASK) == AHC_AIC7770 ) - channel = (aic_inb(p, SBLKCTL) & SELBUSB) >> 3; - else - channel = 0; - - if (aic7xxx_verbose & VERBOSE_RESET) - printk(WARN_LEAD "Someone else reset the channel!!\n", - p->host_no, channel, -1, -1); - if (aic7xxx_panic_on_abort) - aic7xxx_panic_abort(p, NULL); - /* - * Go through and abort all commands for the channel, but do not - * reset the channel again. - */ - aic7xxx_reset_channel(p, channel, /* Initiate Reset */ FALSE); - aic7xxx_run_done_queue(p, TRUE); - scb = NULL; - } - else if ( ((status & BUSFREE) != 0) && ((status & SELTO) == 0) ) - { - /* - * First look at what phase we were last in. If it's message-out, - * chances are pretty good that the bus free was in response to - * one of our abort requests. - */ - unsigned char lastphase = aic_inb(p, LASTPHASE); - unsigned char saved_tcl = aic_inb(p, SAVED_TCL); - unsigned char target = (saved_tcl >> 4) & 0x0F; - int channel; - int printerror = TRUE; - - if ( (p->chip & AHC_CHIPID_MASK) == AHC_AIC7770 ) - channel = (aic_inb(p, SBLKCTL) & SELBUSB) >> 3; - else - channel = 0; - - aic_outb(p, aic_inb(p, SCSISEQ) & (ENSELI|ENRSELI|ENAUTOATNP), - SCSISEQ); - if (lastphase == P_MESGOUT) - { - unsigned char message; - - message = aic_inb(p, SINDEX); - - if ((message == MSG_ABORT) || (message == MSG_ABORT_TAG)) - { - if (aic7xxx_verbose & VERBOSE_ABORT_PROCESS) - printk(INFO_LEAD "SCB %d abort delivered.\n", p->host_no, - CTL_OF_SCB(scb), scb->hscb->tag); - aic7xxx_reset_device(p, target, channel, ALL_LUNS, - (message == MSG_ABORT) ? SCB_LIST_NULL : scb->hscb->tag ); - aic7xxx_run_done_queue(p, TRUE); - scb = NULL; - printerror = 0; - } - else if (message == MSG_BUS_DEV_RESET) - { - aic7xxx_handle_device_reset(p, target, channel); - scb = NULL; - printerror = 0; - } - } - if ( (scb != NULL) && (scb->flags & SCB_DTR_SCB) ) - { - /* - * Hmmm...error during a negotiation command. Either we have a - * borken bus, or the device doesn't like our negotiation message. - * Since we check the INQUIRY data of a device before sending it - * negotiation messages, assume the bus is borken for whatever - * reason. Complete the command. - */ - printerror = 0; - aic7xxx_reset_device(p, target, channel, ALL_LUNS, scb->hscb->tag); - aic7xxx_run_done_queue(p, TRUE); - scb = NULL; - } - if (printerror != 0) - { - if (scb != NULL) - { - unsigned char tag; - - if ((scb->hscb->control & TAG_ENB) != 0) - { - tag = scb->hscb->tag; - } - else - { - tag = SCB_LIST_NULL; - } - aic7xxx_reset_device(p, target, channel, ALL_LUNS, tag); - aic7xxx_run_done_queue(p, TRUE); - } - else - { - aic7xxx_reset_device(p, target, channel, ALL_LUNS, SCB_LIST_NULL); - aic7xxx_run_done_queue(p, TRUE); - } - printk(INFO_LEAD "Unexpected busfree, LASTPHASE = 0x%x, " - "SEQADDR = 0x%x\n", p->host_no, channel, target, -1, lastphase, - (aic_inb(p, SEQADDR1) << 8) | aic_inb(p, SEQADDR0)); - scb = NULL; - } - aic_outb(p, MSG_NOOP, MSG_OUT); - aic_outb(p, aic_inb(p, SIMODE1) & ~(ENBUSFREE|ENREQINIT), - SIMODE1); - p->flags &= ~AHC_HANDLING_REQINITS; - aic_outb(p, CLRBUSFREE, CLRSINT1); - aic_outb(p, CLRSCSIINT, CLRINT); - restart_sequencer(p); - unpause_sequencer(p, TRUE); - } - else if ((status & SELTO) != 0) - { - unsigned char scbptr; - unsigned char nextscb; - struct scsi_cmnd *cmd; - - scbptr = aic_inb(p, WAITING_SCBH); - if (scbptr > p->scb_data->maxhscbs) - { - /* - * I'm still trying to track down exactly how this happens, but until - * I find it, this code will make sure we aren't passing bogus values - * into the SCBPTR register, even if that register will just wrap - * things around, we still don't like having out of range variables. - * - * NOTE: Don't check the aic7xxx_verbose variable, I want this message - * to always be displayed. - */ - printk(INFO_LEAD "Invalid WAITING_SCBH value %d, improvising.\n", - p->host_no, -1, -1, -1, scbptr); - if (p->scb_data->maxhscbs > 4) - scbptr &= (p->scb_data->maxhscbs - 1); - else - scbptr &= 0x03; - } - aic_outb(p, scbptr, SCBPTR); - scb_index = aic_inb(p, SCB_TAG); - - scb = NULL; - if (scb_index < p->scb_data->numscbs) - { - scb = p->scb_data->scb_array[scb_index]; - if ((scb->flags & SCB_ACTIVE) == 0) - { - scb = NULL; - } - } - if (scb == NULL) - { - printk(WARN_LEAD "Referenced SCB %d not valid during SELTO.\n", - p->host_no, -1, -1, -1, scb_index); - printk(KERN_WARNING " SCSISEQ = 0x%x SEQADDR = 0x%x SSTAT0 = 0x%x " - "SSTAT1 = 0x%x\n", aic_inb(p, SCSISEQ), - aic_inb(p, SEQADDR0) | (aic_inb(p, SEQADDR1) << 8), - aic_inb(p, SSTAT0), aic_inb(p, SSTAT1)); - if (aic7xxx_panic_on_abort) - aic7xxx_panic_abort(p, NULL); - } - else - { - cmd = scb->cmd; - cmd->result = (DID_TIME_OUT << 16); - - /* - * Clear out this hardware SCB - */ - aic_outb(p, 0, SCB_CONTROL); - - /* - * Clear out a few values in the card that are in an undetermined - * state. - */ - aic_outb(p, MSG_NOOP, MSG_OUT); - - /* - * Shift the waiting for selection queue forward - */ - nextscb = aic_inb(p, SCB_NEXT); - aic_outb(p, nextscb, WAITING_SCBH); - - /* - * Put this SCB back on the free list. - */ - aic7xxx_add_curscb_to_free_list(p); -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - printk(INFO_LEAD "Selection Timeout.\n", p->host_no, CTL_OF_SCB(scb)); -#endif - if (scb->flags & SCB_QUEUED_ABORT) - { - /* - * We know that this particular SCB had to be the queued abort since - * the disconnected SCB would have gotten a reconnect instead. - * What we need to do then is to let the command timeout again so - * we get a reset since this abort just failed. - */ - cmd->result = 0; - scb = NULL; - } - } - /* - * Keep the sequencer from trying to restart any selections - */ - aic_outb(p, aic_inb(p, SCSISEQ) & ~ENSELO, SCSISEQ); - /* - * Make sure the data bits on the bus are released - * Don't do this on 7770 chipsets, it makes them give us - * a BRKADDRINT and kills the card. - */ - if( (p->chip & ~AHC_CHIPID_MASK) == AHC_PCI ) - aic_outb(p, 0, SCSIBUSL); - - /* - * Delay for the selection timeout delay period then stop the selection - */ - udelay(301); - aic_outb(p, CLRSELINGO, CLRSINT0); - /* - * Clear out all the interrupt status bits - */ - aic_outb(p, aic_inb(p, SIMODE1) & ~(ENREQINIT|ENBUSFREE), SIMODE1); - p->flags &= ~AHC_HANDLING_REQINITS; - aic_outb(p, CLRSELTIMEO | CLRBUSFREE, CLRSINT1); - aic_outb(p, CLRSCSIINT, CLRINT); - /* - * Restarting the sequencer will stop the selection and make sure devices - * are allowed to reselect in. - */ - restart_sequencer(p); - unpause_sequencer(p, TRUE); - } - else if (scb == NULL) - { - printk(WARN_LEAD "aic7xxx_isr - referenced scb not valid " - "during scsiint 0x%x scb(%d)\n" - " SIMODE0 0x%x, SIMODE1 0x%x, SSTAT0 0x%x, SEQADDR 0x%x\n", - p->host_no, -1, -1, -1, status, scb_index, aic_inb(p, SIMODE0), - aic_inb(p, SIMODE1), aic_inb(p, SSTAT0), - (aic_inb(p, SEQADDR1) << 8) | aic_inb(p, SEQADDR0)); - /* - * Turn off the interrupt and set status to zero, so that it - * falls through the rest of the SCSIINT code. - */ - aic_outb(p, status, CLRSINT1); - aic_outb(p, CLRSCSIINT, CLRINT); - unpause_sequencer(p, /* unpause always */ TRUE); - scb = NULL; - } - else if (status & SCSIPERR) - { - /* - * Determine the bus phase and queue an appropriate message. - */ - char *phase; - struct scsi_cmnd *cmd; - unsigned char mesg_out = MSG_NOOP; - unsigned char lastphase = aic_inb(p, LASTPHASE); - unsigned char sstat2 = aic_inb(p, SSTAT2); - - cmd = scb->cmd; - switch (lastphase) - { - case P_DATAOUT: - phase = "Data-Out"; - break; - case P_DATAIN: - phase = "Data-In"; - mesg_out = MSG_INITIATOR_DET_ERR; - break; - case P_COMMAND: - phase = "Command"; - break; - case P_MESGOUT: - phase = "Message-Out"; - break; - case P_STATUS: - phase = "Status"; - mesg_out = MSG_INITIATOR_DET_ERR; - break; - case P_MESGIN: - phase = "Message-In"; - mesg_out = MSG_PARITY_ERROR; - break; - default: - phase = "unknown"; - break; - } - - /* - * A parity error has occurred during a data - * transfer phase. Flag it and continue. - */ - if( (p->features & AHC_ULTRA3) && - (aic_inb(p, SCSIRATE) & AHC_SYNCRATE_CRC) && - (lastphase == P_DATAIN) ) - { - printk(WARN_LEAD "CRC error during %s phase.\n", - p->host_no, CTL_OF_SCB(scb), phase); - if(sstat2 & CRCVALERR) - { - printk(WARN_LEAD " CRC error in intermediate CRC packet.\n", - p->host_no, CTL_OF_SCB(scb)); - } - if(sstat2 & CRCENDERR) - { - printk(WARN_LEAD " CRC error in ending CRC packet.\n", - p->host_no, CTL_OF_SCB(scb)); - } - if(sstat2 & CRCREQERR) - { - printk(WARN_LEAD " Target incorrectly requested a CRC packet.\n", - p->host_no, CTL_OF_SCB(scb)); - } - if(sstat2 & DUAL_EDGE_ERROR) - { - printk(WARN_LEAD " Dual Edge transmission error.\n", - p->host_no, CTL_OF_SCB(scb)); - } - } - else if( (lastphase == P_MESGOUT) && - (scb->flags & SCB_MSGOUT_PPR) ) - { - /* - * As per the draft specs, any device capable of supporting any of - * the option values other than 0 are not allowed to reject the - * PPR message. Instead, they must negotiate out what they do - * support instead of rejecting our offering or else they cause - * a parity error during msg_out phase to signal that they don't - * like our settings. - */ - aic_dev = AIC_DEV(scb->cmd); - aic_dev->needppr = aic_dev->needppr_copy = 0; - aic7xxx_set_width(p, scb->cmd->device->id, scb->cmd->device->channel, scb->cmd->device->lun, - MSG_EXT_WDTR_BUS_8_BIT, - (AHC_TRANS_ACTIVE|AHC_TRANS_CUR|AHC_TRANS_QUITE), - aic_dev); - aic7xxx_set_syncrate(p, NULL, scb->cmd->device->id, scb->cmd->device->channel, 0, 0, - 0, AHC_TRANS_ACTIVE|AHC_TRANS_CUR|AHC_TRANS_QUITE, - aic_dev); - aic_dev->goal.options = 0; - scb->flags &= ~SCB_MSGOUT_BITS; - if(aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "parity error during PPR message, reverting " - "to WDTR/SDTR\n", p->host_no, CTL_OF_SCB(scb)); - } - if ( aic_dev->goal.width ) - { - aic_dev->needwdtr = aic_dev->needwdtr_copy = 1; - } - if ( aic_dev->goal.offset ) - { - if( aic_dev->goal.period <= 9 ) - { - aic_dev->goal.period = 10; - } - aic_dev->needsdtr = aic_dev->needsdtr_copy = 1; - } - scb = NULL; - } - - /* - * We've set the hardware to assert ATN if we get a parity - * error on "in" phases, so all we need to do is stuff the - * message buffer with the appropriate message. "In" phases - * have set mesg_out to something other than MSG_NOP. - */ - if (mesg_out != MSG_NOOP) - { - aic_outb(p, mesg_out, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGI) | ATNO, SCSISIGO); - scb = NULL; - } - aic_outb(p, CLRSCSIPERR, CLRSINT1); - aic_outb(p, CLRSCSIINT, CLRINT); - unpause_sequencer(p, /* unpause_always */ TRUE); - } - else if ( (status & REQINIT) && - (p->flags & AHC_HANDLING_REQINITS) ) - { -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic7xxx_verbose > 0xffff) - printk(INFO_LEAD "Handling REQINIT, SSTAT1=0x%x.\n", p->host_no, - CTL_OF_SCB(scb), aic_inb(p, SSTAT1)); -#endif - aic7xxx_handle_reqinit(p, scb); - return; - } - else - { - /* - * We don't know what's going on. Turn off the - * interrupt source and try to continue. - */ - if (aic7xxx_verbose & VERBOSE_SCSIINT) - printk(INFO_LEAD "Unknown SCSIINT status, SSTAT1(0x%x).\n", - p->host_no, -1, -1, -1, status); - aic_outb(p, status, CLRSINT1); - aic_outb(p, CLRSCSIINT, CLRINT); - unpause_sequencer(p, /* unpause always */ TRUE); - scb = NULL; - } - if (scb != NULL) - { - aic7xxx_done(p, scb); - } -} - -#ifdef AIC7XXX_VERBOSE_DEBUGGING -static void -aic7xxx_check_scbs(struct aic7xxx_host *p, char *buffer) -{ - unsigned char saved_scbptr, free_scbh, dis_scbh, wait_scbh, temp; - int i, bogus, lost; - static unsigned char scb_status[AIC7XXX_MAXSCB]; - -#define SCB_NO_LIST 0 -#define SCB_FREE_LIST 1 -#define SCB_WAITING_LIST 2 -#define SCB_DISCONNECTED_LIST 4 -#define SCB_CURRENTLY_ACTIVE 8 - - /* - * Note, these checks will fail on a regular basis once the machine moves - * beyond the bus scan phase. The problem is race conditions concerning - * the scbs and where they are linked in. When you have 30 or so commands - * outstanding on the bus, and run this twice with every interrupt, the - * chances get pretty good that you'll catch the sequencer with an SCB - * only partially linked in. Therefore, once we pass the scan phase - * of the bus, we really should disable this function. - */ - bogus = FALSE; - memset(&scb_status[0], 0, sizeof(scb_status)); - pause_sequencer(p); - saved_scbptr = aic_inb(p, SCBPTR); - if (saved_scbptr >= p->scb_data->maxhscbs) - { - printk("Bogus SCBPTR %d\n", saved_scbptr); - bogus = TRUE; - } - scb_status[saved_scbptr] = SCB_CURRENTLY_ACTIVE; - free_scbh = aic_inb(p, FREE_SCBH); - if ( (free_scbh != SCB_LIST_NULL) && - (free_scbh >= p->scb_data->maxhscbs) ) - { - printk("Bogus FREE_SCBH %d\n", free_scbh); - bogus = TRUE; - } - else - { - temp = free_scbh; - while( (temp != SCB_LIST_NULL) && (temp < p->scb_data->maxhscbs) ) - { - if(scb_status[temp] & 0x07) - { - printk("HSCB %d on multiple lists, status 0x%02x", temp, - scb_status[temp] | SCB_FREE_LIST); - bogus = TRUE; - } - scb_status[temp] |= SCB_FREE_LIST; - aic_outb(p, temp, SCBPTR); - temp = aic_inb(p, SCB_NEXT); - } - } - - dis_scbh = aic_inb(p, DISCONNECTED_SCBH); - if ( (dis_scbh != SCB_LIST_NULL) && - (dis_scbh >= p->scb_data->maxhscbs) ) - { - printk("Bogus DISCONNECTED_SCBH %d\n", dis_scbh); - bogus = TRUE; - } - else - { - temp = dis_scbh; - while( (temp != SCB_LIST_NULL) && (temp < p->scb_data->maxhscbs) ) - { - if(scb_status[temp] & 0x07) - { - printk("HSCB %d on multiple lists, status 0x%02x", temp, - scb_status[temp] | SCB_DISCONNECTED_LIST); - bogus = TRUE; - } - scb_status[temp] |= SCB_DISCONNECTED_LIST; - aic_outb(p, temp, SCBPTR); - temp = aic_inb(p, SCB_NEXT); - } - } - - wait_scbh = aic_inb(p, WAITING_SCBH); - if ( (wait_scbh != SCB_LIST_NULL) && - (wait_scbh >= p->scb_data->maxhscbs) ) - { - printk("Bogus WAITING_SCBH %d\n", wait_scbh); - bogus = TRUE; - } - else - { - temp = wait_scbh; - while( (temp != SCB_LIST_NULL) && (temp < p->scb_data->maxhscbs) ) - { - if(scb_status[temp] & 0x07) - { - printk("HSCB %d on multiple lists, status 0x%02x", temp, - scb_status[temp] | SCB_WAITING_LIST); - bogus = TRUE; - } - scb_status[temp] |= SCB_WAITING_LIST; - aic_outb(p, temp, SCBPTR); - temp = aic_inb(p, SCB_NEXT); - } - } - - lost=0; - for(i=0; i < p->scb_data->maxhscbs; i++) - { - aic_outb(p, i, SCBPTR); - temp = aic_inb(p, SCB_NEXT); - if ( ((temp != SCB_LIST_NULL) && - (temp >= p->scb_data->maxhscbs)) ) - { - printk("HSCB %d bad, SCB_NEXT invalid(%d).\n", i, temp); - bogus = TRUE; - } - if ( temp == i ) - { - printk("HSCB %d bad, SCB_NEXT points to self.\n", i); - bogus = TRUE; - } - if (scb_status[i] == 0) - lost++; - if (lost > 1) - { - printk("Too many lost scbs.\n"); - bogus=TRUE; - } - } - aic_outb(p, saved_scbptr, SCBPTR); - unpause_sequencer(p, FALSE); - if (bogus) - { - printk("Bogus parameters found in card SCB array structures.\n"); - printk("%s\n", buffer); - aic7xxx_panic_abort(p, NULL); - } - return; -} -#endif - - -/*+F************************************************************************* - * Function: - * aic7xxx_handle_command_completion_intr - * - * Description: - * SCSI command completion interrupt handler. - *-F*************************************************************************/ -static void -aic7xxx_handle_command_completion_intr(struct aic7xxx_host *p) -{ - struct aic7xxx_scb *scb = NULL; - struct aic_dev_data *aic_dev; - struct scsi_cmnd *cmd; - unsigned char scb_index, tindex; - -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if( (p->isr_count < 16) && (aic7xxx_verbose > 0xffff) ) - printk(INFO_LEAD "Command Complete Int.\n", p->host_no, -1, -1, -1); -#endif - - /* - * Read the INTSTAT location after clearing the CMDINT bit. This forces - * any posted PCI writes to flush to memory. Gerard Roudier suggested - * this fix to the possible race of clearing the CMDINT bit but not - * having all command bytes flushed onto the qoutfifo. - */ - aic_outb(p, CLRCMDINT, CLRINT); - aic_inb(p, INTSTAT); - /* - * The sequencer will continue running when it - * issues this interrupt. There may be >1 commands - * finished, so loop until we've processed them all. - */ - - while (p->qoutfifo[p->qoutfifonext] != SCB_LIST_NULL) - { - scb_index = p->qoutfifo[p->qoutfifonext]; - p->qoutfifo[p->qoutfifonext++] = SCB_LIST_NULL; - if ( scb_index >= p->scb_data->numscbs ) - { - printk(WARN_LEAD "CMDCMPLT with invalid SCB index %d\n", p->host_no, - -1, -1, -1, scb_index); - continue; - } - scb = p->scb_data->scb_array[scb_index]; - if (!(scb->flags & SCB_ACTIVE) || (scb->cmd == NULL)) - { - printk(WARN_LEAD "CMDCMPLT without command for SCB %d, SCB flags " - "0x%x, cmd 0x%lx\n", p->host_no, -1, -1, -1, scb_index, scb->flags, - (unsigned long) scb->cmd); - continue; - } - tindex = TARGET_INDEX(scb->cmd); - aic_dev = AIC_DEV(scb->cmd); - if (scb->flags & SCB_QUEUED_ABORT) - { - pause_sequencer(p); - if ( ((aic_inb(p, LASTPHASE) & PHASE_MASK) != P_BUSFREE) && - (aic_inb(p, SCB_TAG) == scb->hscb->tag) ) - { - unpause_sequencer(p, FALSE); - continue; - } - aic7xxx_reset_device(p, scb->cmd->device->id, scb->cmd->device->channel, - scb->cmd->device->lun, scb->hscb->tag); - scb->flags &= ~(SCB_QUEUED_FOR_DONE | SCB_RESET | SCB_ABORT | - SCB_QUEUED_ABORT); - unpause_sequencer(p, FALSE); - } - else if (scb->flags & SCB_ABORT) - { - /* - * We started to abort this, but it completed on us, let it - * through as successful - */ - scb->flags &= ~(SCB_ABORT|SCB_RESET); - } - else if (scb->flags & SCB_SENSE) - { - char *buffer = &scb->cmd->sense_buffer[0]; - - if (buffer[12] == 0x47 || buffer[12] == 0x54) - { - /* - * Signal that we need to re-negotiate things. - */ - aic_dev->needppr = aic_dev->needppr_copy; - aic_dev->needsdtr = aic_dev->needsdtr_copy; - aic_dev->needwdtr = aic_dev->needwdtr_copy; - } - } - cmd = scb->cmd; - if (scb->hscb->residual_SG_segment_count != 0) - { - aic7xxx_calculate_residual(p, scb); - } - cmd->result |= (aic7xxx_error(cmd) << 16); - aic7xxx_done(p, scb); - } -} - -/*+F************************************************************************* - * Function: - * aic7xxx_isr - * - * Description: - * SCSI controller interrupt handler. - *-F*************************************************************************/ -static void -aic7xxx_isr(void *dev_id) -{ - struct aic7xxx_host *p; - unsigned char intstat; - - p = dev_id; - - /* - * Just a few sanity checks. Make sure that we have an int pending. - * Also, if PCI, then we are going to check for a PCI bus error status - * should we get too many spurious interrupts. - */ - if (!((intstat = aic_inb(p, INTSTAT)) & INT_PEND)) - { -#ifdef CONFIG_PCI - if ( (p->chip & AHC_PCI) && (p->spurious_int > 500) && - !(p->flags & AHC_HANDLING_REQINITS) ) - { - if ( aic_inb(p, ERROR) & PCIERRSTAT ) - { - aic7xxx_pci_intr(p); - } - p->spurious_int = 0; - } - else if ( !(p->flags & AHC_HANDLING_REQINITS) ) - { - p->spurious_int++; - } -#endif - return; - } - - p->spurious_int = 0; - - /* - * Keep track of interrupts for /proc/scsi - */ - p->isr_count++; - -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if ( (p->isr_count < 16) && (aic7xxx_verbose > 0xffff) && - (aic7xxx_panic_on_abort) && (p->flags & AHC_PAGESCBS) ) - aic7xxx_check_scbs(p, "Bogus settings at start of interrupt."); -#endif - - /* - * Handle all the interrupt sources - especially for SCSI - * interrupts, we won't get a second chance at them. - */ - if (intstat & CMDCMPLT) - { - aic7xxx_handle_command_completion_intr(p); - } - - if (intstat & BRKADRINT) - { - int i; - unsigned char errno = aic_inb(p, ERROR); - - printk(KERN_ERR "(scsi%d) BRKADRINT error(0x%x):\n", p->host_no, errno); - for (i = 0; i < ARRAY_SIZE(hard_error); i++) - { - if (errno & hard_error[i].errno) - { - printk(KERN_ERR " %s\n", hard_error[i].errmesg); - } - } - printk(KERN_ERR "(scsi%d) SEQADDR=0x%x\n", p->host_no, - (((aic_inb(p, SEQADDR1) << 8) & 0x100) | aic_inb(p, SEQADDR0))); - if (aic7xxx_panic_on_abort) - aic7xxx_panic_abort(p, NULL); -#ifdef CONFIG_PCI - if (errno & PCIERRSTAT) - aic7xxx_pci_intr(p); -#endif - if (errno & (SQPARERR | ILLOPCODE | ILLSADDR)) - { - panic("aic7xxx: unrecoverable BRKADRINT.\n"); - } - if (errno & ILLHADDR) - { - printk(KERN_ERR "(scsi%d) BUG! Driver accessed chip without first " - "pausing controller!\n", p->host_no); - } -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (errno & DPARERR) - { - if (aic_inb(p, DMAPARAMS) & DIRECTION) - printk("(scsi%d) while DMAing SCB from host to card.\n", p->host_no); - else - printk("(scsi%d) while DMAing SCB from card to host.\n", p->host_no); - } -#endif - aic_outb(p, CLRPARERR | CLRBRKADRINT, CLRINT); - unpause_sequencer(p, FALSE); - } - - if (intstat & SEQINT) - { - /* - * Read the CCSCBCTL register to work around a bug in the Ultra2 cards - */ - if(p->features & AHC_ULTRA2) - { - aic_inb(p, CCSCBCTL); - } - aic7xxx_handle_seqint(p, intstat); - } - - if (intstat & SCSIINT) - { - aic7xxx_handle_scsiint(p, intstat); - } - -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if ( (p->isr_count < 16) && (aic7xxx_verbose > 0xffff) && - (aic7xxx_panic_on_abort) && (p->flags & AHC_PAGESCBS) ) - aic7xxx_check_scbs(p, "Bogus settings at end of interrupt."); -#endif - -} - -/*+F************************************************************************* - * Function: - * do_aic7xxx_isr - * - * Description: - * This is a gross hack to solve a problem in linux kernels 2.1.85 and - * above. Please, children, do not try this at home, and if you ever see - * anything like it, please inform the Gross Hack Police immediately - *-F*************************************************************************/ -static irqreturn_t -do_aic7xxx_isr(int irq, void *dev_id) -{ - unsigned long cpu_flags; - struct aic7xxx_host *p; - - p = dev_id; - if(!p) - return IRQ_NONE; - spin_lock_irqsave(p->host->host_lock, cpu_flags); - p->flags |= AHC_IN_ISR; - do - { - aic7xxx_isr(dev_id); - } while ( (aic_inb(p, INTSTAT) & INT_PEND) ); - aic7xxx_done_cmds_complete(p); - aic7xxx_run_waiting_queues(p); - p->flags &= ~AHC_IN_ISR; - spin_unlock_irqrestore(p->host->host_lock, cpu_flags); - - return IRQ_HANDLED; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_init_transinfo - * - * Description: - * Set up the initial aic_dev values from the BIOS settings and from - * INQUIRY results - *-F*************************************************************************/ -static void -aic7xxx_init_transinfo(struct aic7xxx_host *p, struct aic_dev_data *aic_dev) -{ - struct scsi_device *sdpnt = aic_dev->SDptr; - unsigned char tindex; - - tindex = sdpnt->id | (sdpnt->channel << 3); - if (!(aic_dev->flags & DEVICE_DTR_SCANNED)) - { - aic_dev->flags |= DEVICE_DTR_SCANNED; - - if ( sdpnt->wdtr && (p->features & AHC_WIDE) ) - { - aic_dev->needwdtr = aic_dev->needwdtr_copy = 1; - aic_dev->goal.width = p->user[tindex].width; - } - else - { - aic_dev->needwdtr = aic_dev->needwdtr_copy = 0; - pause_sequencer(p); - aic7xxx_set_width(p, sdpnt->id, sdpnt->channel, sdpnt->lun, - MSG_EXT_WDTR_BUS_8_BIT, (AHC_TRANS_ACTIVE | - AHC_TRANS_GOAL | - AHC_TRANS_CUR), aic_dev ); - unpause_sequencer(p, FALSE); - } - if ( sdpnt->sdtr && p->user[tindex].offset ) - { - aic_dev->goal.period = p->user[tindex].period; - aic_dev->goal.options = p->user[tindex].options; - if (p->features & AHC_ULTRA2) - aic_dev->goal.offset = MAX_OFFSET_ULTRA2; - else if (aic_dev->goal.width == MSG_EXT_WDTR_BUS_16_BIT) - aic_dev->goal.offset = MAX_OFFSET_16BIT; - else - aic_dev->goal.offset = MAX_OFFSET_8BIT; - if ( sdpnt->ppr && p->user[tindex].period <= 9 && - p->user[tindex].options ) - { - aic_dev->needppr = aic_dev->needppr_copy = 1; - aic_dev->needsdtr = aic_dev->needsdtr_copy = 0; - aic_dev->needwdtr = aic_dev->needwdtr_copy = 0; - aic_dev->flags |= DEVICE_SCSI_3; - } - else - { - aic_dev->needsdtr = aic_dev->needsdtr_copy = 1; - aic_dev->goal.period = max_t(unsigned char, 10, aic_dev->goal.period); - aic_dev->goal.options = 0; - } - } - else - { - aic_dev->needsdtr = aic_dev->needsdtr_copy = 0; - aic_dev->goal.period = 255; - aic_dev->goal.offset = 0; - aic_dev->goal.options = 0; - } - aic_dev->flags |= DEVICE_PRINT_DTR; - } -} - -/*+F************************************************************************* - * Function: - * aic7xxx_slave_alloc - * - * Description: - * Set up the initial aic_dev struct pointers - *-F*************************************************************************/ -static int -aic7xxx_slave_alloc(struct scsi_device *SDptr) -{ - struct aic7xxx_host *p = (struct aic7xxx_host *)SDptr->host->hostdata; - struct aic_dev_data *aic_dev; - - aic_dev = kmalloc(sizeof(struct aic_dev_data), GFP_KERNEL); - if(!aic_dev) - return 1; - /* - * Check to see if channel was scanned. - */ - - if (!(p->flags & AHC_A_SCANNED) && (SDptr->channel == 0)) - { - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(INFO_LEAD "Scanning channel for devices.\n", - p->host_no, 0, -1, -1); - p->flags |= AHC_A_SCANNED; - } - else - { - if (!(p->flags & AHC_B_SCANNED) && (SDptr->channel == 1)) - { - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(INFO_LEAD "Scanning channel for devices.\n", - p->host_no, 1, -1, -1); - p->flags |= AHC_B_SCANNED; - } - } - - memset(aic_dev, 0, sizeof(struct aic_dev_data)); - SDptr->hostdata = aic_dev; - aic_dev->SDptr = SDptr; - aic_dev->max_q_depth = 1; - aic_dev->temp_q_depth = 1; - scbq_init(&aic_dev->delayed_scbs); - INIT_LIST_HEAD(&aic_dev->list); - list_add_tail(&aic_dev->list, &p->aic_devs); - return 0; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_device_queue_depth - * - * Description: - * Determines the queue depth for a given device. There are two ways - * a queue depth can be obtained for a tagged queueing device. One - * way is the default queue depth which is determined by whether - * aic7xxx_default_queue_depth. The other is by the aic7xxx_tag_info - * array. - * - * If tagged queueing isn't supported on the device, then we set the - * depth to p->host->hostt->cmd_per_lun for internal driver queueing. - * as the default queue depth. Otherwise, we use either 4 or 8 as the - * default queue depth (dependent on the number of hardware SCBs). - * The other way we determine queue depth is through the use of the - * aic7xxx_tag_info array which is enabled by defining - * AIC7XXX_TAGGED_QUEUEING_BY_DEVICE. This array can be initialized - * with queue depths for individual devices. It also allows tagged - * queueing to be [en|dis]abled for a specific adapter. - *-F*************************************************************************/ -static void -aic7xxx_device_queue_depth(struct aic7xxx_host *p, struct scsi_device *device) -{ - int tag_enabled = FALSE; - struct aic_dev_data *aic_dev = device->hostdata; - unsigned char tindex; - - tindex = device->id | (device->channel << 3); - - if (device->simple_tags) - return; // We've already enabled this device - - if (device->tagged_supported) - { - tag_enabled = TRUE; - - if (!(p->discenable & (1 << tindex))) - { - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - printk(INFO_LEAD "Disconnection disabled, unable to " - "enable tagged queueing.\n", - p->host_no, device->channel, device->id, device->lun); - tag_enabled = FALSE; - } - else - { - if (p->instance >= ARRAY_SIZE(aic7xxx_tag_info)) - { - static int print_warning = TRUE; - if(print_warning) - { - printk(KERN_INFO "aic7xxx: WARNING, insufficient tag_info instances for" - " installed controllers.\n"); - printk(KERN_INFO "aic7xxx: Please update the aic7xxx_tag_info array in" - " the aic7xxx.c source file.\n"); - print_warning = FALSE; - } - aic_dev->max_q_depth = aic_dev->temp_q_depth = - aic7xxx_default_queue_depth; - } - else - { - - if (aic7xxx_tag_info[p->instance].tag_commands[tindex] == 255) - { - tag_enabled = FALSE; - } - else if (aic7xxx_tag_info[p->instance].tag_commands[tindex] == 0) - { - aic_dev->max_q_depth = aic_dev->temp_q_depth = - aic7xxx_default_queue_depth; - } - else - { - aic_dev->max_q_depth = aic_dev->temp_q_depth = - aic7xxx_tag_info[p->instance].tag_commands[tindex]; - } - } - } - } - if (tag_enabled) - { - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Tagged queuing enabled, queue depth %d.\n", - p->host_no, device->channel, device->id, - device->lun, aic_dev->max_q_depth); - } - scsi_adjust_queue_depth(device, MSG_ORDERED_TAG, aic_dev->max_q_depth); - } - else - { - if (aic7xxx_verbose & VERBOSE_NEGOTIATION2) - { - printk(INFO_LEAD "Tagged queuing disabled, queue depth %d.\n", - p->host_no, device->channel, device->id, - device->lun, device->host->cmd_per_lun); - } - scsi_adjust_queue_depth(device, 0, device->host->cmd_per_lun); - } - return; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_slave_destroy - * - * Description: - * prepare for this device to go away - *-F*************************************************************************/ -static void -aic7xxx_slave_destroy(struct scsi_device *SDptr) -{ - struct aic_dev_data *aic_dev = SDptr->hostdata; - - list_del(&aic_dev->list); - SDptr->hostdata = NULL; - kfree(aic_dev); - return; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_slave_configure - * - * Description: - * Configure the device we are attaching to the controller. This is - * where we get to do things like scan the INQUIRY data, set queue - * depths, allocate command structs, etc. - *-F*************************************************************************/ -static int -aic7xxx_slave_configure(struct scsi_device *SDptr) -{ - struct aic7xxx_host *p = (struct aic7xxx_host *) SDptr->host->hostdata; - struct aic_dev_data *aic_dev; - int scbnum; - - aic_dev = (struct aic_dev_data *)SDptr->hostdata; - - aic7xxx_init_transinfo(p, aic_dev); - aic7xxx_device_queue_depth(p, SDptr); - if(list_empty(&aic_dev->list)) - list_add_tail(&aic_dev->list, &p->aic_devs); - - scbnum = 0; - list_for_each_entry(aic_dev, &p->aic_devs, list) { - scbnum += aic_dev->max_q_depth; - } - while (scbnum > p->scb_data->numscbs) - { - /* - * Pre-allocate the needed SCBs to get around the possibility of having - * to allocate some when memory is more or less exhausted and we need - * the SCB in order to perform a swap operation (possible deadlock) - */ - if ( aic7xxx_allocate_scb(p) == 0 ) - break; - } - - - return(0); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_probe - * - * Description: - * Probing for EISA boards: it looks like the first two bytes - * are a manufacturer code - three characters, five bits each: - * - * BYTE 0 BYTE 1 BYTE 2 BYTE 3 - * ?1111122 22233333 PPPPPPPP RRRRRRRR - * - * The characters are baselined off ASCII '@', so add that value - * to each to get the real ASCII code for it. The next two bytes - * appear to be a product and revision number, probably vendor- - * specific. This is what is being searched for at each port, - * and what should probably correspond to the ID= field in the - * ECU's .cfg file for the card - if your card is not detected, - * make sure your signature is listed in the array. - * - * The fourth byte's lowest bit seems to be an enabled/disabled - * flag (rest of the bits are reserved?). - * - * NOTE: This function is only needed on Intel and Alpha platforms, - * the other platforms we support don't have EISA/VLB busses. So, - * we #ifdef this entire function to avoid compiler warnings about - * an unused function. - *-F*************************************************************************/ -#if defined(__i386__) || defined(__alpha__) -static int -aic7xxx_probe(int slot, int base, ahc_flag_type *flags) -{ - int i; - unsigned char buf[4]; - - static struct { - int n; - unsigned char signature[sizeof(buf)]; - ahc_chip type; - int bios_disabled; - } AIC7xxx[] = { - { 4, { 0x04, 0x90, 0x77, 0x70 }, - AHC_AIC7770|AHC_EISA, FALSE }, /* mb 7770 */ - { 4, { 0x04, 0x90, 0x77, 0x71 }, - AHC_AIC7770|AHC_EISA, FALSE }, /* host adapter 274x */ - { 4, { 0x04, 0x90, 0x77, 0x56 }, - AHC_AIC7770|AHC_VL, FALSE }, /* 284x BIOS enabled */ - { 4, { 0x04, 0x90, 0x77, 0x57 }, - AHC_AIC7770|AHC_VL, TRUE } /* 284x BIOS disabled */ - }; - - /* - * The VL-bus cards need to be primed by - * writing before a signature check. - */ - for (i = 0; i < sizeof(buf); i++) - { - outb(0x80 + i, base); - buf[i] = inb(base + i); - } - - for (i = 0; i < ARRAY_SIZE(AIC7xxx); i++) - { - /* - * Signature match on enabled card? - */ - if (!memcmp(buf, AIC7xxx[i].signature, AIC7xxx[i].n)) - { - if (inb(base + 4) & 1) - { - if (AIC7xxx[i].bios_disabled) - { - *flags |= AHC_USEDEFAULTS; - } - else - { - *flags |= AHC_BIOS_ENABLED; - } - return (i); - } - - printk("aic7xxx: <Adaptec 7770 SCSI Host Adapter> " - "disabled at slot %d, ignored.\n", slot); - } - } - - return (-1); -} -#endif /* (__i386__) || (__alpha__) */ - - -/*+F************************************************************************* - * Function: - * read_2840_seeprom - * - * Description: - * Reads the 2840 serial EEPROM and returns 1 if successful and 0 if - * not successful. - * - * See read_seeprom (for the 2940) for the instruction set of the 93C46 - * chip. - * - * The 2840 interface to the 93C46 serial EEPROM is through the - * STATUS_2840 and SEECTL_2840 registers. The CS_2840, CK_2840, and - * DO_2840 bits of the SEECTL_2840 register are connected to the chip - * select, clock, and data out lines respectively of the serial EEPROM. - * The DI_2840 bit of the STATUS_2840 is connected to the data in line - * of the serial EEPROM. The EEPROM_TF bit of STATUS_2840 register is - * useful in that it gives us an 800 nsec timer. After a read from the - * SEECTL_2840 register the timing flag is cleared and goes high 800 nsec - * later. - *-F*************************************************************************/ -static int -read_284x_seeprom(struct aic7xxx_host *p, struct seeprom_config *sc) -{ - int i = 0, k = 0; - unsigned char temp; - unsigned short checksum = 0; - unsigned short *seeprom = (unsigned short *) sc; - struct seeprom_cmd { - unsigned char len; - unsigned char bits[3]; - }; - struct seeprom_cmd seeprom_read = {3, {1, 1, 0}}; - -#define CLOCK_PULSE(p) \ - while ((aic_inb(p, STATUS_2840) & EEPROM_TF) == 0) \ - { \ - ; /* Do nothing */ \ - } \ - (void) aic_inb(p, SEECTL_2840); - - /* - * Read the first 32 registers of the seeprom. For the 2840, - * the 93C46 SEEPROM is a 1024-bit device with 64 16-bit registers - * but only the first 32 are used by Adaptec BIOS. The loop - * will range from 0 to 31. - */ - for (k = 0; k < (sizeof(*sc) / 2); k++) - { - /* - * Send chip select for one clock cycle. - */ - aic_outb(p, CK_2840 | CS_2840, SEECTL_2840); - CLOCK_PULSE(p); - - /* - * Now we're ready to send the read command followed by the - * address of the 16-bit register we want to read. - */ - for (i = 0; i < seeprom_read.len; i++) - { - temp = CS_2840 | seeprom_read.bits[i]; - aic_outb(p, temp, SEECTL_2840); - CLOCK_PULSE(p); - temp = temp ^ CK_2840; - aic_outb(p, temp, SEECTL_2840); - CLOCK_PULSE(p); - } - /* - * Send the 6 bit address (MSB first, LSB last). - */ - for (i = 5; i >= 0; i--) - { - temp = k; - temp = (temp >> i) & 1; /* Mask out all but lower bit. */ - temp = CS_2840 | temp; - aic_outb(p, temp, SEECTL_2840); - CLOCK_PULSE(p); - temp = temp ^ CK_2840; - aic_outb(p, temp, SEECTL_2840); - CLOCK_PULSE(p); - } - - /* - * Now read the 16 bit register. An initial 0 precedes the - * register contents which begins with bit 15 (MSB) and ends - * with bit 0 (LSB). The initial 0 will be shifted off the - * top of our word as we let the loop run from 0 to 16. - */ - for (i = 0; i <= 16; i++) - { - temp = CS_2840; - aic_outb(p, temp, SEECTL_2840); - CLOCK_PULSE(p); - temp = temp ^ CK_2840; - seeprom[k] = (seeprom[k] << 1) | (aic_inb(p, STATUS_2840) & DI_2840); - aic_outb(p, temp, SEECTL_2840); - CLOCK_PULSE(p); - } - /* - * The serial EEPROM has a checksum in the last word. Keep a - * running checksum for all words read except for the last - * word. We'll verify the checksum after all words have been - * read. - */ - if (k < (sizeof(*sc) / 2) - 1) - { - checksum = checksum + seeprom[k]; - } - - /* - * Reset the chip select for the next command cycle. - */ - aic_outb(p, 0, SEECTL_2840); - CLOCK_PULSE(p); - aic_outb(p, CK_2840, SEECTL_2840); - CLOCK_PULSE(p); - aic_outb(p, 0, SEECTL_2840); - CLOCK_PULSE(p); - } - -#if 0 - printk("Computed checksum 0x%x, checksum read 0x%x\n", checksum, sc->checksum); - printk("Serial EEPROM:"); - for (k = 0; k < (sizeof(*sc) / 2); k++) - { - if (((k % 8) == 0) && (k != 0)) - { - printk("\n "); - } - printk(" 0x%x", seeprom[k]); - } - printk("\n"); -#endif - - if (checksum != sc->checksum) - { - printk("aic7xxx: SEEPROM checksum error, ignoring SEEPROM settings.\n"); - return (0); - } - - return (1); -#undef CLOCK_PULSE -} - -#define CLOCK_PULSE(p) \ - do { \ - int limit = 0; \ - do { \ - mb(); \ - pause_sequencer(p); /* This is just to generate some PCI */ \ - /* traffic so the PCI read is flushed */ \ - /* it shouldn't be needed, but some */ \ - /* chipsets do indeed appear to need */ \ - /* something to force PCI reads to get */ \ - /* flushed */ \ - udelay(1); /* Do nothing */ \ - } while (((aic_inb(p, SEECTL) & SEERDY) == 0) && (++limit < 1000)); \ - } while(0) - -/*+F************************************************************************* - * Function: - * acquire_seeprom - * - * Description: - * Acquires access to the memory port on PCI controllers. - *-F*************************************************************************/ -static int -acquire_seeprom(struct aic7xxx_host *p) -{ - - /* - * Request access of the memory port. When access is - * granted, SEERDY will go high. We use a 1 second - * timeout which should be near 1 second more than - * is needed. Reason: after the 7870 chip reset, there - * should be no contention. - */ - aic_outb(p, SEEMS, SEECTL); - CLOCK_PULSE(p); - if ((aic_inb(p, SEECTL) & SEERDY) == 0) - { - aic_outb(p, 0, SEECTL); - return (0); - } - return (1); -} - -/*+F************************************************************************* - * Function: - * release_seeprom - * - * Description: - * Releases access to the memory port on PCI controllers. - *-F*************************************************************************/ -static void -release_seeprom(struct aic7xxx_host *p) -{ - /* - * Make sure the SEEPROM is ready before we release it. - */ - CLOCK_PULSE(p); - aic_outb(p, 0, SEECTL); -} - -/*+F************************************************************************* - * Function: - * read_seeprom - * - * Description: - * Reads the serial EEPROM and returns 1 if successful and 0 if - * not successful. - * - * The instruction set of the 93C46/56/66 chips is as follows: - * - * Start OP - * Function Bit Code Address Data Description - * ------------------------------------------------------------------- - * READ 1 10 A5 - A0 Reads data stored in memory, - * starting at specified address - * EWEN 1 00 11XXXX Write enable must precede - * all programming modes - * ERASE 1 11 A5 - A0 Erase register A5A4A3A2A1A0 - * WRITE 1 01 A5 - A0 D15 - D0 Writes register - * ERAL 1 00 10XXXX Erase all registers - * WRAL 1 00 01XXXX D15 - D0 Writes to all registers - * EWDS 1 00 00XXXX Disables all programming - * instructions - * *Note: A value of X for address is a don't care condition. - * *Note: The 93C56 and 93C66 have 8 address bits. - * - * - * The 93C46 has a four wire interface: clock, chip select, data in, and - * data out. In order to perform one of the above functions, you need - * to enable the chip select for a clock period (typically a minimum of - * 1 usec, with the clock high and low a minimum of 750 and 250 nsec - * respectively. While the chip select remains high, you can clock in - * the instructions (above) starting with the start bit, followed by the - * OP code, Address, and Data (if needed). For the READ instruction, the - * requested 16-bit register contents is read from the data out line but - * is preceded by an initial zero (leading 0, followed by 16-bits, MSB - * first). The clock cycling from low to high initiates the next data - * bit to be sent from the chip. - * - * The 78xx interface to the 93C46 serial EEPROM is through the SEECTL - * register. After successful arbitration for the memory port, the - * SEECS bit of the SEECTL register is connected to the chip select. - * The SEECK, SEEDO, and SEEDI are connected to the clock, data out, - * and data in lines respectively. The SEERDY bit of SEECTL is useful - * in that it gives us an 800 nsec timer. After a write to the SEECTL - * register, the SEERDY goes high 800 nsec later. The one exception - * to this is when we first request access to the memory port. The - * SEERDY goes high to signify that access has been granted and, for - * this case, has no implied timing. - *-F*************************************************************************/ -static int -read_seeprom(struct aic7xxx_host *p, int offset, - unsigned short *scarray, unsigned int len, seeprom_chip_type chip) -{ - int i = 0, k; - unsigned char temp; - unsigned short checksum = 0; - struct seeprom_cmd { - unsigned char len; - unsigned char bits[3]; - }; - struct seeprom_cmd seeprom_read = {3, {1, 1, 0}}; - - /* - * Request access of the memory port. - */ - if (acquire_seeprom(p) == 0) - { - return (0); - } - - /* - * Read 'len' registers of the seeprom. For the 7870, the 93C46 - * SEEPROM is a 1024-bit device with 64 16-bit registers but only - * the first 32 are used by Adaptec BIOS. Some adapters use the - * 93C56 SEEPROM which is a 2048-bit device. The loop will range - * from 0 to 'len' - 1. - */ - for (k = 0; k < len; k++) - { - /* - * Send chip select for one clock cycle. - */ - aic_outb(p, SEEMS | SEECK | SEECS, SEECTL); - CLOCK_PULSE(p); - - /* - * Now we're ready to send the read command followed by the - * address of the 16-bit register we want to read. - */ - for (i = 0; i < seeprom_read.len; i++) - { - temp = SEEMS | SEECS | (seeprom_read.bits[i] << 1); - aic_outb(p, temp, SEECTL); - CLOCK_PULSE(p); - temp = temp ^ SEECK; - aic_outb(p, temp, SEECTL); - CLOCK_PULSE(p); - } - /* - * Send the 6 or 8 bit address (MSB first, LSB last). - */ - for (i = ((int) chip - 1); i >= 0; i--) - { - temp = k + offset; - temp = (temp >> i) & 1; /* Mask out all but lower bit. */ - temp = SEEMS | SEECS | (temp << 1); - aic_outb(p, temp, SEECTL); - CLOCK_PULSE(p); - temp = temp ^ SEECK; - aic_outb(p, temp, SEECTL); - CLOCK_PULSE(p); - } - - /* - * Now read the 16 bit register. An initial 0 precedes the - * register contents which begins with bit 15 (MSB) and ends - * with bit 0 (LSB). The initial 0 will be shifted off the - * top of our word as we let the loop run from 0 to 16. - */ - for (i = 0; i <= 16; i++) - { - temp = SEEMS | SEECS; - aic_outb(p, temp, SEECTL); - CLOCK_PULSE(p); - temp = temp ^ SEECK; - scarray[k] = (scarray[k] << 1) | (aic_inb(p, SEECTL) & SEEDI); - aic_outb(p, temp, SEECTL); - CLOCK_PULSE(p); - } - - /* - * The serial EEPROM should have a checksum in the last word. - * Keep a running checksum for all words read except for the - * last word. We'll verify the checksum after all words have - * been read. - */ - if (k < (len - 1)) - { - checksum = checksum + scarray[k]; - } - - /* - * Reset the chip select for the next command cycle. - */ - aic_outb(p, SEEMS, SEECTL); - CLOCK_PULSE(p); - aic_outb(p, SEEMS | SEECK, SEECTL); - CLOCK_PULSE(p); - aic_outb(p, SEEMS, SEECTL); - CLOCK_PULSE(p); - } - - /* - * Release access to the memory port and the serial EEPROM. - */ - release_seeprom(p); - -#if 0 - printk("Computed checksum 0x%x, checksum read 0x%x\n", - checksum, scarray[len - 1]); - printk("Serial EEPROM:"); - for (k = 0; k < len; k++) - { - if (((k % 8) == 0) && (k != 0)) - { - printk("\n "); - } - printk(" 0x%x", scarray[k]); - } - printk("\n"); -#endif - if ( (checksum != scarray[len - 1]) || (checksum == 0) ) - { - return (0); - } - - return (1); -} - -/*+F************************************************************************* - * Function: - * read_brdctl - * - * Description: - * Reads the BRDCTL register. - *-F*************************************************************************/ -static unsigned char -read_brdctl(struct aic7xxx_host *p) -{ - unsigned char brdctl, value; - - /* - * Make sure the SEEPROM is ready before we access it - */ - CLOCK_PULSE(p); - if (p->features & AHC_ULTRA2) - { - brdctl = BRDRW_ULTRA2; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - value = aic_inb(p, BRDCTL); - CLOCK_PULSE(p); - return(value); - } - brdctl = BRDRW; - if ( !((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) || - (p->flags & AHC_CHNLB) ) - { - brdctl |= BRDCS; - } - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - value = aic_inb(p, BRDCTL); - CLOCK_PULSE(p); - aic_outb(p, 0, BRDCTL); - CLOCK_PULSE(p); - return (value); -} - -/*+F************************************************************************* - * Function: - * write_brdctl - * - * Description: - * Writes a value to the BRDCTL register. - *-F*************************************************************************/ -static void -write_brdctl(struct aic7xxx_host *p, unsigned char value) -{ - unsigned char brdctl; - - /* - * Make sure the SEEPROM is ready before we access it - */ - CLOCK_PULSE(p); - if (p->features & AHC_ULTRA2) - { - brdctl = value; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - brdctl |= BRDSTB_ULTRA2; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - brdctl &= ~BRDSTB_ULTRA2; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - read_brdctl(p); - CLOCK_PULSE(p); - } - else - { - brdctl = BRDSTB; - if ( !((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) || - (p->flags & AHC_CHNLB) ) - { - brdctl |= BRDCS; - } - brdctl = BRDSTB | BRDCS; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - brdctl |= value; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - brdctl &= ~BRDSTB; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - brdctl &= ~BRDCS; - aic_outb(p, brdctl, BRDCTL); - CLOCK_PULSE(p); - } -} - -/*+F************************************************************************* - * Function: - * aic785x_cable_detect - * - * Description: - * Detect the cables that are present on aic785x class controller chips - *-F*************************************************************************/ -static void -aic785x_cable_detect(struct aic7xxx_host *p, int *int_50, - int *ext_present, int *eeprom) -{ - unsigned char brdctl; - - aic_outb(p, BRDRW | BRDCS, BRDCTL); - CLOCK_PULSE(p); - aic_outb(p, 0, BRDCTL); - CLOCK_PULSE(p); - brdctl = aic_inb(p, BRDCTL); - CLOCK_PULSE(p); - *int_50 = !(brdctl & BRDDAT5); - *ext_present = !(brdctl & BRDDAT6); - *eeprom = (aic_inb(p, SPIOCAP) & EEPROM); -} - -#undef CLOCK_PULSE - -/*+F************************************************************************* - * Function: - * aic2940_uwpro_cable_detect - * - * Description: - * Detect the cables that are present on the 2940-UWPro cards - * - * NOTE: This function assumes the SEEPROM will have already been acquired - * prior to invocation of this function. - *-F*************************************************************************/ -static void -aic2940_uwpro_wide_cable_detect(struct aic7xxx_host *p, int *int_68, - int *ext_68, int *eeprom) -{ - unsigned char brdctl; - - /* - * First read the status of our cables. Set the rom bank to - * 0 since the bank setting serves as a multiplexor for the - * cable detection logic. BRDDAT5 controls the bank switch. - */ - write_brdctl(p, 0); - - /* - * Now we read the state of the internal 68 connector. BRDDAT6 - * is don't care, BRDDAT7 is internal 68. The cable is - * present if the bit is 0 - */ - brdctl = read_brdctl(p); - *int_68 = !(brdctl & BRDDAT7); - - /* - * Set the bank bit in brdctl and then read the external cable state - * and the EEPROM status - */ - write_brdctl(p, BRDDAT5); - brdctl = read_brdctl(p); - - *ext_68 = !(brdctl & BRDDAT6); - *eeprom = !(brdctl & BRDDAT7); - - /* - * We're done, the calling function will release the SEEPROM for us - */ -} - -/*+F************************************************************************* - * Function: - * aic787x_cable_detect - * - * Description: - * Detect the cables that are present on aic787x class controller chips - * - * NOTE: This function assumes the SEEPROM will have already been acquired - * prior to invocation of this function. - *-F*************************************************************************/ -static void -aic787x_cable_detect(struct aic7xxx_host *p, int *int_50, int *int_68, - int *ext_present, int *eeprom) -{ - unsigned char brdctl; - - /* - * First read the status of our cables. Set the rom bank to - * 0 since the bank setting serves as a multiplexor for the - * cable detection logic. BRDDAT5 controls the bank switch. - */ - write_brdctl(p, 0); - - /* - * Now we read the state of the two internal connectors. BRDDAT6 - * is internal 50, BRDDAT7 is internal 68. For each, the cable is - * present if the bit is 0 - */ - brdctl = read_brdctl(p); - *int_50 = !(brdctl & BRDDAT6); - *int_68 = !(brdctl & BRDDAT7); - - /* - * Set the bank bit in brdctl and then read the external cable state - * and the EEPROM status - */ - write_brdctl(p, BRDDAT5); - brdctl = read_brdctl(p); - - *ext_present = !(brdctl & BRDDAT6); - *eeprom = !(brdctl & BRDDAT7); - - /* - * We're done, the calling function will release the SEEPROM for us - */ -} - -/*+F************************************************************************* - * Function: - * aic787x_ultra2_term_detect - * - * Description: - * Detect the termination settings present on ultra2 class controllers - * - * NOTE: This function assumes the SEEPROM will have already been acquired - * prior to invocation of this function. - *-F*************************************************************************/ -static void -aic7xxx_ultra2_term_detect(struct aic7xxx_host *p, int *enableSE_low, - int *enableSE_high, int *enableLVD_low, - int *enableLVD_high, int *eprom_present) -{ - unsigned char brdctl; - - brdctl = read_brdctl(p); - - *eprom_present = (brdctl & BRDDAT7); - *enableSE_high = (brdctl & BRDDAT6); - *enableSE_low = (brdctl & BRDDAT5); - *enableLVD_high = (brdctl & BRDDAT4); - *enableLVD_low = (brdctl & BRDDAT3); -} - -/*+F************************************************************************* - * Function: - * configure_termination - * - * Description: - * Configures the termination settings on PCI adapters that have - * SEEPROMs available. - *-F*************************************************************************/ -static void -configure_termination(struct aic7xxx_host *p) -{ - int internal50_present = 0; - int internal68_present = 0; - int external_present = 0; - int eprom_present = 0; - int enableSE_low = 0; - int enableSE_high = 0; - int enableLVD_low = 0; - int enableLVD_high = 0; - unsigned char brddat = 0; - unsigned char max_target = 0; - unsigned char sxfrctl1 = aic_inb(p, SXFRCTL1); - - if (acquire_seeprom(p)) - { - if (p->features & (AHC_WIDE|AHC_TWIN)) - max_target = 16; - else - max_target = 8; - aic_outb(p, SEEMS | SEECS, SEECTL); - sxfrctl1 &= ~STPWEN; - /* - * The termination/cable detection logic is split into three distinct - * groups. Ultra2 and later controllers, 2940UW-Pro controllers, and - * older 7850, 7860, 7870, 7880, and 7895 controllers. Each has its - * own unique way of detecting their cables and writing the results - * back to the card. - */ - if (p->features & AHC_ULTRA2) - { - /* - * As long as user hasn't overridden term settings, always check the - * cable detection logic - */ - if (aic7xxx_override_term == -1) - { - aic7xxx_ultra2_term_detect(p, &enableSE_low, &enableSE_high, - &enableLVD_low, &enableLVD_high, - &eprom_present); - } - - /* - * If the user is overriding settings, then they have been preserved - * to here as fake adapter_control entries. Parse them and allow - * them to override the detected settings (if we even did detection). - */ - if (!(p->adapter_control & CFSEAUTOTERM)) - { - enableSE_low = (p->adapter_control & CFSTERM); - enableSE_high = (p->adapter_control & CFWSTERM); - } - if (!(p->adapter_control & CFAUTOTERM)) - { - enableLVD_low = enableLVD_high = (p->adapter_control & CFLVDSTERM); - } - - /* - * Now take those settings that we have and translate them into the - * values that must be written into the registers. - * - * Flash Enable = BRDDAT7 - * Secondary High Term Enable = BRDDAT6 - * Secondary Low Term Enable = BRDDAT5 - * LVD/Primary High Term Enable = BRDDAT4 - * LVD/Primary Low Term Enable = STPWEN bit in SXFRCTL1 - */ - if (enableLVD_low != 0) - { - sxfrctl1 |= STPWEN; - p->flags |= AHC_TERM_ENB_LVD; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) LVD/Primary Low byte termination " - "Enabled\n", p->host_no); - } - - if (enableLVD_high != 0) - { - brddat |= BRDDAT4; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) LVD/Primary High byte termination " - "Enabled\n", p->host_no); - } - - if (enableSE_low != 0) - { - brddat |= BRDDAT5; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) Secondary Low byte termination " - "Enabled\n", p->host_no); - } - - if (enableSE_high != 0) - { - brddat |= BRDDAT6; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) Secondary High byte termination " - "Enabled\n", p->host_no); - } - } - else if (p->features & AHC_NEW_AUTOTERM) - { - /* - * The 50 pin connector termination is controlled by STPWEN in the - * SXFRCTL1 register. Since the Adaptec docs typically say the - * controller is not allowed to be in the middle of a cable and - * this is the only connection on that stub of the bus, there is - * no need to even check for narrow termination, it's simply - * always on. - */ - sxfrctl1 |= STPWEN; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) Narrow channel termination Enabled\n", - p->host_no); - - if (p->adapter_control & CFAUTOTERM) - { - aic2940_uwpro_wide_cable_detect(p, &internal68_present, - &external_present, - &eprom_present); - printk(KERN_INFO "(scsi%d) Cables present (Int-50 %s, Int-68 %s, " - "Ext-68 %s)\n", p->host_no, - "Don't Care", - internal68_present ? "YES" : "NO", - external_present ? "YES" : "NO"); - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) EEPROM %s present.\n", p->host_no, - eprom_present ? "is" : "is not"); - if (internal68_present && external_present) - { - brddat = 0; - p->flags &= ~AHC_TERM_ENB_SE_HIGH; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) Wide channel termination Disabled\n", - p->host_no); - } - else - { - brddat = BRDDAT6; - p->flags |= AHC_TERM_ENB_SE_HIGH; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) Wide channel termination Enabled\n", - p->host_no); - } - } - else - { - /* - * The termination of the Wide channel is done more like normal - * though, and the setting of this termination is done by writing - * either a 0 or 1 to BRDDAT6 of the BRDDAT register - */ - if (p->adapter_control & CFWSTERM) - { - brddat = BRDDAT6; - p->flags |= AHC_TERM_ENB_SE_HIGH; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) Wide channel termination Enabled\n", - p->host_no); - } - else - { - brddat = 0; - } - } - } - else - { - if (p->adapter_control & CFAUTOTERM) - { - if (p->flags & AHC_MOTHERBOARD) - { - printk(KERN_INFO "(scsi%d) Warning - detected auto-termination\n", - p->host_no); - printk(KERN_INFO "(scsi%d) Please verify driver detected settings " - "are correct.\n", p->host_no); - printk(KERN_INFO "(scsi%d) If not, then please properly set the " - "device termination\n", p->host_no); - printk(KERN_INFO "(scsi%d) in the Adaptec SCSI BIOS by hitting " - "CTRL-A when prompted\n", p->host_no); - printk(KERN_INFO "(scsi%d) during machine bootup.\n", p->host_no); - } - /* Configure auto termination. */ - - if ( (p->chip & AHC_CHIPID_MASK) >= AHC_AIC7870 ) - { - aic787x_cable_detect(p, &internal50_present, &internal68_present, - &external_present, &eprom_present); - } - else - { - aic785x_cable_detect(p, &internal50_present, &external_present, - &eprom_present); - } - - if (max_target <= 8) - internal68_present = 0; - - if (max_target > 8) - { - printk(KERN_INFO "(scsi%d) Cables present (Int-50 %s, Int-68 %s, " - "Ext-68 %s)\n", p->host_no, - internal50_present ? "YES" : "NO", - internal68_present ? "YES" : "NO", - external_present ? "YES" : "NO"); - } - else - { - printk(KERN_INFO "(scsi%d) Cables present (Int-50 %s, Ext-50 %s)\n", - p->host_no, - internal50_present ? "YES" : "NO", - external_present ? "YES" : "NO"); - } - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) EEPROM %s present.\n", p->host_no, - eprom_present ? "is" : "is not"); - - /* - * Now set the termination based on what we found. BRDDAT6 - * controls wide termination enable. - * Flash Enable = BRDDAT7 - * SE High Term Enable = BRDDAT6 - */ - if (internal50_present && internal68_present && external_present) - { - printk(KERN_INFO "(scsi%d) Illegal cable configuration!! Only two\n", - p->host_no); - printk(KERN_INFO "(scsi%d) connectors on the SCSI controller may be " - "in use at a time!\n", p->host_no); - /* - * Force termination (low and high byte) on. This is safer than - * leaving it completely off, especially since this message comes - * most often from motherboard controllers that don't even have 3 - * connectors, but instead are failing the cable detection. - */ - internal50_present = external_present = 0; - enableSE_high = enableSE_low = 1; - } - - if ((max_target > 8) && - ((external_present == 0) || (internal68_present == 0)) ) - { - brddat |= BRDDAT6; - p->flags |= AHC_TERM_ENB_SE_HIGH; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) SE High byte termination Enabled\n", - p->host_no); - } - - if ( ((internal50_present ? 1 : 0) + - (internal68_present ? 1 : 0) + - (external_present ? 1 : 0)) <= 1 ) - { - sxfrctl1 |= STPWEN; - p->flags |= AHC_TERM_ENB_SE_LOW; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) SE Low byte termination Enabled\n", - p->host_no); - } - } - else /* p->adapter_control & CFAUTOTERM */ - { - if (p->adapter_control & CFSTERM) - { - sxfrctl1 |= STPWEN; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) SE Low byte termination Enabled\n", - p->host_no); - } - - if (p->adapter_control & CFWSTERM) - { - brddat |= BRDDAT6; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) SE High byte termination Enabled\n", - p->host_no); - } - } - } - - aic_outb(p, sxfrctl1, SXFRCTL1); - write_brdctl(p, brddat); - release_seeprom(p); - } -} - -/*+F************************************************************************* - * Function: - * detect_maxscb - * - * Description: - * Detects the maximum number of SCBs for the controller and returns - * the count and a mask in p (p->maxscbs, p->qcntmask). - *-F*************************************************************************/ -static void -detect_maxscb(struct aic7xxx_host *p) -{ - int i; - - /* - * It's possible that we've already done this for multichannel - * adapters. - */ - if (p->scb_data->maxhscbs == 0) - { - /* - * We haven't initialized the SCB settings yet. Walk the SCBs to - * determince how many there are. - */ - aic_outb(p, 0, FREE_SCBH); - - for (i = 0; i < AIC7XXX_MAXSCB; i++) - { - aic_outb(p, i, SCBPTR); - aic_outb(p, i, SCB_CONTROL); - if (aic_inb(p, SCB_CONTROL) != i) - break; - aic_outb(p, 0, SCBPTR); - if (aic_inb(p, SCB_CONTROL) != 0) - break; - - aic_outb(p, i, SCBPTR); - aic_outb(p, 0, SCB_CONTROL); /* Clear the control byte. */ - aic_outb(p, i + 1, SCB_NEXT); /* Set the next pointer. */ - aic_outb(p, SCB_LIST_NULL, SCB_TAG); /* Make the tag invalid. */ - aic_outb(p, SCB_LIST_NULL, SCB_BUSYTARGETS); /* no busy untagged */ - aic_outb(p, SCB_LIST_NULL, SCB_BUSYTARGETS+1);/* targets active yet */ - aic_outb(p, SCB_LIST_NULL, SCB_BUSYTARGETS+2); - aic_outb(p, SCB_LIST_NULL, SCB_BUSYTARGETS+3); - } - - /* Make sure the last SCB terminates the free list. */ - aic_outb(p, i - 1, SCBPTR); - aic_outb(p, SCB_LIST_NULL, SCB_NEXT); - - /* Ensure we clear the first (0) SCBs control byte. */ - aic_outb(p, 0, SCBPTR); - aic_outb(p, 0, SCB_CONTROL); - - p->scb_data->maxhscbs = i; - /* - * Use direct indexing instead for speed - */ - if ( i == AIC7XXX_MAXSCB ) - p->flags &= ~AHC_PAGESCBS; - } - -} - -/*+F************************************************************************* - * Function: - * aic7xxx_register - * - * Description: - * Register a Adaptec aic7xxx chip SCSI controller with the kernel. - *-F*************************************************************************/ -static int -aic7xxx_register(struct scsi_host_template *template, struct aic7xxx_host *p, - int reset_delay) -{ - int i, result; - int max_targets; - int found = 1; - unsigned char term, scsi_conf; - struct Scsi_Host *host; - - host = p->host; - - p->scb_data->maxscbs = AIC7XXX_MAXSCB; - host->can_queue = AIC7XXX_MAXSCB; - host->cmd_per_lun = 3; - host->sg_tablesize = AIC7XXX_MAX_SG; - host->this_id = p->scsi_id; - host->io_port = p->base; - host->n_io_port = 0xFF; - host->base = p->mbase; - host->irq = p->irq; - if (p->features & AHC_WIDE) - { - host->max_id = 16; - } - if (p->features & AHC_TWIN) - { - host->max_channel = 1; - } - - p->host = host; - p->host_no = host->host_no; - host->unique_id = p->instance; - p->isr_count = 0; - p->next = NULL; - p->completeq.head = NULL; - p->completeq.tail = NULL; - scbq_init(&p->scb_data->free_scbs); - scbq_init(&p->waiting_scbs); - INIT_LIST_HEAD(&p->aic_devs); - - /* - * We currently have no commands of any type - */ - p->qinfifonext = 0; - p->qoutfifonext = 0; - - printk(KERN_INFO "(scsi%d) <%s> found at ", p->host_no, - board_names[p->board_name_index]); - switch(p->chip) - { - case (AHC_AIC7770|AHC_EISA): - printk("EISA slot %d\n", p->pci_device_fn); - break; - case (AHC_AIC7770|AHC_VL): - printk("VLB slot %d\n", p->pci_device_fn); - break; - default: - printk("PCI %d/%d/%d\n", p->pci_bus, PCI_SLOT(p->pci_device_fn), - PCI_FUNC(p->pci_device_fn)); - break; - } - if (p->features & AHC_TWIN) - { - printk(KERN_INFO "(scsi%d) Twin Channel, A SCSI ID %d, B SCSI ID %d, ", - p->host_no, p->scsi_id, p->scsi_id_b); - } - else - { - char *channel; - - channel = ""; - - if ((p->flags & AHC_MULTI_CHANNEL) != 0) - { - channel = " A"; - - if ( (p->flags & (AHC_CHNLB|AHC_CHNLC)) != 0 ) - { - channel = (p->flags & AHC_CHNLB) ? " B" : " C"; - } - } - if (p->features & AHC_WIDE) - { - printk(KERN_INFO "(scsi%d) Wide ", p->host_no); - } - else - { - printk(KERN_INFO "(scsi%d) Narrow ", p->host_no); - } - printk("Channel%s, SCSI ID=%d, ", channel, p->scsi_id); - } - aic_outb(p, 0, SEQ_FLAGS); - - detect_maxscb(p); - - printk("%d/%d SCBs\n", p->scb_data->maxhscbs, p->scb_data->maxscbs); - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk(KERN_INFO "(scsi%d) BIOS %sabled, IO Port 0x%lx, IRQ %d\n", - p->host_no, (p->flags & AHC_BIOS_ENABLED) ? "en" : "dis", - p->base, p->irq); - printk(KERN_INFO "(scsi%d) IO Memory at 0x%lx, MMAP Memory at %p\n", - p->host_no, p->mbase, p->maddr); - } - -#ifdef CONFIG_PCI - /* - * Now that we know our instance number, we can set the flags we need to - * force termination if need be. - */ - if (aic7xxx_stpwlev != -1) - { - /* - * This option only applies to PCI controllers. - */ - if ( (p->chip & ~AHC_CHIPID_MASK) == AHC_PCI) - { - unsigned char devconfig; - - pci_read_config_byte(p->pdev, DEVCONFIG, &devconfig); - if ( (aic7xxx_stpwlev >> p->instance) & 0x01 ) - { - devconfig |= STPWLEVEL; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk("(scsi%d) Force setting STPWLEVEL bit\n", p->host_no); - } - else - { - devconfig &= ~STPWLEVEL; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk("(scsi%d) Force clearing STPWLEVEL bit\n", p->host_no); - } - pci_write_config_byte(p->pdev, DEVCONFIG, devconfig); - } - } -#endif - - /* - * That took care of devconfig and stpwlev, now for the actual termination - * settings. - */ - if (aic7xxx_override_term != -1) - { - /* - * Again, this only applies to PCI controllers. We don't have problems - * with the termination on 274x controllers to the best of my knowledge. - */ - if ( (p->chip & ~AHC_CHIPID_MASK) == AHC_PCI) - { - unsigned char term_override; - - term_override = ( (aic7xxx_override_term >> (p->instance * 4)) & 0x0f); - p->adapter_control &= - ~(CFSTERM|CFWSTERM|CFLVDSTERM|CFAUTOTERM|CFSEAUTOTERM); - if ( (p->features & AHC_ULTRA2) && (term_override & 0x0c) ) - { - p->adapter_control |= CFLVDSTERM; - } - if (term_override & 0x02) - { - p->adapter_control |= CFWSTERM; - } - if (term_override & 0x01) - { - p->adapter_control |= CFSTERM; - } - } - } - - if ( (p->flags & AHC_SEEPROM_FOUND) || (aic7xxx_override_term != -1) ) - { - if (p->features & AHC_SPIOCAP) - { - if ( aic_inb(p, SPIOCAP) & SSPIOCPS ) - /* - * Update the settings in sxfrctl1 to match the termination - * settings. - */ - configure_termination(p); - } - else if ((p->chip & AHC_CHIPID_MASK) >= AHC_AIC7870) - { - configure_termination(p); - } - } - - /* - * Set the SCSI Id, SXFRCTL0, SXFRCTL1, and SIMODE1, for both channels - */ - if (p->features & AHC_TWIN) - { - /* Select channel B */ - aic_outb(p, aic_inb(p, SBLKCTL) | SELBUSB, SBLKCTL); - - if ((p->flags & AHC_SEEPROM_FOUND) || (aic7xxx_override_term != -1)) - term = (aic_inb(p, SXFRCTL1) & STPWEN); - else - term = ((p->flags & AHC_TERM_ENB_B) ? STPWEN : 0); - - aic_outb(p, p->scsi_id_b, SCSIID); - scsi_conf = aic_inb(p, SCSICONF + 1); - aic_outb(p, DFON | SPIOEN, SXFRCTL0); - aic_outb(p, (scsi_conf & ENSPCHK) | aic7xxx_seltime | term | - ENSTIMER | ACTNEGEN, SXFRCTL1); - aic_outb(p, 0, SIMODE0); - aic_outb(p, ENSELTIMO | ENSCSIRST | ENSCSIPERR, SIMODE1); - aic_outb(p, 0, SCSIRATE); - - /* Select channel A */ - aic_outb(p, aic_inb(p, SBLKCTL) & ~SELBUSB, SBLKCTL); - } - - if (p->features & AHC_ULTRA2) - { - aic_outb(p, p->scsi_id, SCSIID_ULTRA2); - } - else - { - aic_outb(p, p->scsi_id, SCSIID); - } - if ((p->flags & AHC_SEEPROM_FOUND) || (aic7xxx_override_term != -1)) - term = (aic_inb(p, SXFRCTL1) & STPWEN); - else - term = ((p->flags & (AHC_TERM_ENB_A|AHC_TERM_ENB_LVD)) ? STPWEN : 0); - scsi_conf = aic_inb(p, SCSICONF); - aic_outb(p, DFON | SPIOEN, SXFRCTL0); - aic_outb(p, (scsi_conf & ENSPCHK) | aic7xxx_seltime | term | - ENSTIMER | ACTNEGEN, SXFRCTL1); - aic_outb(p, 0, SIMODE0); - /* - * If we are a cardbus adapter then don't enable SCSI reset detection. - * We shouldn't likely be sharing SCSI busses with someone else, and - * if we don't have a cable currently plugged into the controller then - * we won't have a power source for the SCSI termination, which means - * we'll see infinite incoming bus resets. - */ - if(p->flags & AHC_NO_STPWEN) - aic_outb(p, ENSELTIMO | ENSCSIPERR, SIMODE1); - else - aic_outb(p, ENSELTIMO | ENSCSIRST | ENSCSIPERR, SIMODE1); - aic_outb(p, 0, SCSIRATE); - if ( p->features & AHC_ULTRA2) - aic_outb(p, 0, SCSIOFFSET); - - /* - * Look at the information that board initialization or the board - * BIOS has left us. In the lower four bits of each target's - * scratch space any value other than 0 indicates that we should - * initiate synchronous transfers. If it's zero, the user or the - * BIOS has decided to disable synchronous negotiation to that - * target so we don't activate the needsdtr flag. - */ - if ((p->features & (AHC_TWIN|AHC_WIDE)) == 0) - { - max_targets = 8; - } - else - { - max_targets = 16; - } - - if (!(aic7xxx_no_reset)) - { - /* - * If we reset the bus, then clear the transfer settings, else leave - * them be. - */ - aic_outb(p, 0, ULTRA_ENB); - aic_outb(p, 0, ULTRA_ENB + 1); - p->ultraenb = 0; - } - - /* - * Allocate enough hardware scbs to handle the maximum number of - * concurrent transactions we can have. We have to make sure that - * the allocated memory is contiguous memory. The Linux kmalloc - * routine should only allocate contiguous memory, but note that - * this could be a problem if kmalloc() is changed. - */ - { - size_t array_size; - unsigned int hscb_physaddr; - - array_size = p->scb_data->maxscbs * sizeof(struct aic7xxx_hwscb); - if (p->scb_data->hscbs == NULL) - { - /* pci_alloc_consistent enforces the alignment already and - * clears the area as well. - */ - p->scb_data->hscbs = pci_alloc_consistent(p->pdev, array_size, - &p->scb_data->hscbs_dma); - /* We have to use pci_free_consistent, not kfree */ - p->scb_data->hscb_kmalloc_ptr = NULL; - p->scb_data->hscbs_dma_len = array_size; - } - if (p->scb_data->hscbs == NULL) - { - printk("(scsi%d) Unable to allocate hardware SCB array; " - "failing detection.\n", p->host_no); - aic_outb(p, 0, SIMODE1); - p->irq = 0; - return(0); - } - - hscb_physaddr = p->scb_data->hscbs_dma; - aic_outb(p, hscb_physaddr & 0xFF, HSCB_ADDR); - aic_outb(p, (hscb_physaddr >> 8) & 0xFF, HSCB_ADDR + 1); - aic_outb(p, (hscb_physaddr >> 16) & 0xFF, HSCB_ADDR + 2); - aic_outb(p, (hscb_physaddr >> 24) & 0xFF, HSCB_ADDR + 3); - - /* Set up the fifo areas at the same time */ - p->untagged_scbs = pci_alloc_consistent(p->pdev, 3*256, &p->fifo_dma); - if (p->untagged_scbs == NULL) - { - printk("(scsi%d) Unable to allocate hardware FIFO arrays; " - "failing detection.\n", p->host_no); - p->irq = 0; - return(0); - } - - p->qoutfifo = p->untagged_scbs + 256; - p->qinfifo = p->qoutfifo + 256; - for (i = 0; i < 256; i++) - { - p->untagged_scbs[i] = SCB_LIST_NULL; - p->qinfifo[i] = SCB_LIST_NULL; - p->qoutfifo[i] = SCB_LIST_NULL; - } - - hscb_physaddr = p->fifo_dma; - aic_outb(p, hscb_physaddr & 0xFF, SCBID_ADDR); - aic_outb(p, (hscb_physaddr >> 8) & 0xFF, SCBID_ADDR + 1); - aic_outb(p, (hscb_physaddr >> 16) & 0xFF, SCBID_ADDR + 2); - aic_outb(p, (hscb_physaddr >> 24) & 0xFF, SCBID_ADDR + 3); - } - - /* The Q-FIFOs we just set up are all empty */ - aic_outb(p, 0, QINPOS); - aic_outb(p, 0, KERNEL_QINPOS); - aic_outb(p, 0, QOUTPOS); - - if(p->features & AHC_QUEUE_REGS) - { - aic_outb(p, SCB_QSIZE_256, QOFF_CTLSTA); - aic_outb(p, 0, SDSCB_QOFF); - aic_outb(p, 0, SNSCB_QOFF); - aic_outb(p, 0, HNSCB_QOFF); - } - - /* - * We don't have any waiting selections or disconnected SCBs. - */ - aic_outb(p, SCB_LIST_NULL, WAITING_SCBH); - aic_outb(p, SCB_LIST_NULL, DISCONNECTED_SCBH); - - /* - * Message out buffer starts empty - */ - aic_outb(p, MSG_NOOP, MSG_OUT); - aic_outb(p, MSG_NOOP, LAST_MSG); - - /* - * Set all the other asundry items that haven't been set yet. - * This includes just dumping init values to a lot of registers simply - * to make sure they've been touched and are ready for use parity wise - * speaking. - */ - aic_outb(p, 0, TMODE_CMDADDR); - aic_outb(p, 0, TMODE_CMDADDR + 1); - aic_outb(p, 0, TMODE_CMDADDR + 2); - aic_outb(p, 0, TMODE_CMDADDR + 3); - aic_outb(p, 0, TMODE_CMDADDR_NEXT); - - /* - * Link us into the list of valid hosts - */ - p->next = first_aic7xxx; - first_aic7xxx = p; - - /* - * Allocate the first set of scbs for this controller. This is to stream- - * line code elsewhere in the driver. If we have to check for the existence - * of scbs in certain code sections, it slows things down. However, as - * soon as we register the IRQ for this card, we could get an interrupt that - * includes possibly the SCSI_RSTI interrupt. If we catch that interrupt - * then we are likely to segfault if we don't have at least one chunk of - * SCBs allocated or add checks all through the reset code to make sure - * that the SCBs have been allocated which is an invalid running condition - * and therefore I think it's preferable to simply pre-allocate the first - * chunk of SCBs. - */ - aic7xxx_allocate_scb(p); - - /* - * Load the sequencer program, then re-enable the board - - * resetting the AIC-7770 disables it, leaving the lights - * on with nobody home. - */ - aic7xxx_loadseq(p); - - /* - * Make sure the AUTOFLUSHDIS bit is *not* set in the SBLKCTL register - */ - aic_outb(p, aic_inb(p, SBLKCTL) & ~AUTOFLUSHDIS, SBLKCTL); - - if ( (p->chip & AHC_CHIPID_MASK) == AHC_AIC7770 ) - { - aic_outb(p, ENABLE, BCTL); /* Enable the boards BUS drivers. */ - } - - if ( !(aic7xxx_no_reset) ) - { - if (p->features & AHC_TWIN) - { - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk(KERN_INFO "(scsi%d) Resetting channel B\n", p->host_no); - aic_outb(p, aic_inb(p, SBLKCTL) | SELBUSB, SBLKCTL); - aic7xxx_reset_current_bus(p); - aic_outb(p, aic_inb(p, SBLKCTL) & ~SELBUSB, SBLKCTL); - } - /* Reset SCSI bus A. */ - if (aic7xxx_verbose & VERBOSE_PROBE2) - { /* In case we are a 3940, 3985, or 7895, print the right channel */ - char *channel = ""; - if (p->flags & AHC_MULTI_CHANNEL) - { - channel = " A"; - if (p->flags & (AHC_CHNLB|AHC_CHNLC)) - channel = (p->flags & AHC_CHNLB) ? " B" : " C"; - } - printk(KERN_INFO "(scsi%d) Resetting channel%s\n", p->host_no, channel); - } - - aic7xxx_reset_current_bus(p); - - } - else - { - if (!reset_delay) - { - printk(KERN_INFO "(scsi%d) Not resetting SCSI bus. Note: Don't use " - "the no_reset\n", p->host_no); - printk(KERN_INFO "(scsi%d) option unless you have a verifiable need " - "for it.\n", p->host_no); - } - } - - /* - * Register IRQ with the kernel. Only allow sharing IRQs with - * PCI devices. - */ - if (!(p->chip & AHC_PCI)) - { - result = (request_irq(p->irq, do_aic7xxx_isr, 0, "aic7xxx", p)); - } - else - { - result = (request_irq(p->irq, do_aic7xxx_isr, IRQF_SHARED, - "aic7xxx", p)); - if (result < 0) - { - result = (request_irq(p->irq, do_aic7xxx_isr, IRQF_DISABLED | IRQF_SHARED, - "aic7xxx", p)); - } - } - if (result < 0) - { - printk(KERN_WARNING "(scsi%d) Couldn't register IRQ %d, ignoring " - "controller.\n", p->host_no, p->irq); - aic_outb(p, 0, SIMODE1); - p->irq = 0; - return (0); - } - - if(aic_inb(p, INTSTAT) & INT_PEND) - printk(INFO_LEAD "spurious interrupt during configuration, cleared.\n", - p->host_no, -1, -1 , -1); - aic7xxx_clear_intstat(p); - - unpause_sequencer(p, /* unpause_always */ TRUE); - - return (found); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_chip_reset - * - * Description: - * Perform a chip reset on the aic7xxx SCSI controller. The controller - * is paused upon return. - *-F*************************************************************************/ -static int -aic7xxx_chip_reset(struct aic7xxx_host *p) -{ - unsigned char sblkctl; - int wait; - - /* - * For some 274x boards, we must clear the CHIPRST bit and pause - * the sequencer. For some reason, this makes the driver work. - */ - aic_outb(p, PAUSE | CHIPRST, HCNTRL); - - /* - * In the future, we may call this function as a last resort for - * error handling. Let's be nice and not do any unnecessary delays. - */ - wait = 1000; /* 1 msec (1000 * 1 msec) */ - while (--wait && !(aic_inb(p, HCNTRL) & CHIPRSTACK)) - { - udelay(1); /* 1 usec */ - } - - pause_sequencer(p); - - sblkctl = aic_inb(p, SBLKCTL) & (SELBUSB|SELWIDE); - if (p->chip & AHC_PCI) - sblkctl &= ~SELBUSB; - switch( sblkctl ) - { - case 0: /* normal narrow card */ - break; - case 2: /* Wide card */ - p->features |= AHC_WIDE; - break; - case 8: /* Twin card */ - p->features |= AHC_TWIN; - p->flags |= AHC_MULTI_CHANNEL; - break; - default: /* hmmm...we don't know what this is */ - printk(KERN_WARNING "aic7xxx: Unsupported adapter type %d, ignoring.\n", - aic_inb(p, SBLKCTL) & 0x0a); - return(-1); - } - return(0); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_alloc - * - * Description: - * Allocate and initialize a host structure. Returns NULL upon error - * and a pointer to a aic7xxx_host struct upon success. - *-F*************************************************************************/ -static struct aic7xxx_host * -aic7xxx_alloc(struct scsi_host_template *sht, struct aic7xxx_host *temp) -{ - struct aic7xxx_host *p = NULL; - struct Scsi_Host *host; - - /* - * Allocate a storage area by registering us with the mid-level - * SCSI layer. - */ - host = scsi_register(sht, sizeof(struct aic7xxx_host)); - - if (host != NULL) - { - p = (struct aic7xxx_host *) host->hostdata; - memset(p, 0, sizeof(struct aic7xxx_host)); - *p = *temp; - p->host = host; - - p->scb_data = kzalloc(sizeof(scb_data_type), GFP_ATOMIC); - if (p->scb_data) - { - scbq_init (&p->scb_data->free_scbs); - } - else - { - /* - * For some reason we don't have enough memory. Free the - * allocated memory for the aic7xxx_host struct, and return NULL. - */ - release_region(p->base, MAXREG - MINREG); - scsi_unregister(host); - return(NULL); - } - p->host_no = host->host_no; - } - return (p); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_free - * - * Description: - * Frees and releases all resources associated with an instance of - * the driver (struct aic7xxx_host *). - *-F*************************************************************************/ -static void -aic7xxx_free(struct aic7xxx_host *p) -{ - int i; - - /* - * Free the allocated hardware SCB space. - */ - if (p->scb_data != NULL) - { - struct aic7xxx_scb_dma *scb_dma = NULL; - if (p->scb_data->hscbs != NULL) - { - pci_free_consistent(p->pdev, p->scb_data->hscbs_dma_len, - p->scb_data->hscbs, p->scb_data->hscbs_dma); - p->scb_data->hscbs = p->scb_data->hscb_kmalloc_ptr = NULL; - } - /* - * Free the driver SCBs. These were allocated on an as-need - * basis. We allocated these in groups depending on how many - * we could fit into a given amount of RAM. The tail SCB for - * these allocations has a pointer to the alloced area. - */ - for (i = 0; i < p->scb_data->numscbs; i++) - { - if (p->scb_data->scb_array[i]->scb_dma != scb_dma) - { - scb_dma = p->scb_data->scb_array[i]->scb_dma; - pci_free_consistent(p->pdev, scb_dma->dma_len, - (void *)((unsigned long)scb_dma->dma_address - - scb_dma->dma_offset), - scb_dma->dma_address); - } - kfree(p->scb_data->scb_array[i]->kmalloc_ptr); - p->scb_data->scb_array[i] = NULL; - } - - /* - * Free the SCB data area. - */ - kfree(p->scb_data); - } - - pci_free_consistent(p->pdev, 3*256, (void *)p->untagged_scbs, p->fifo_dma); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_load_seeprom - * - * Description: - * Load the seeprom and configure adapter and target settings. - * Returns 1 if the load was successful and 0 otherwise. - *-F*************************************************************************/ -static void -aic7xxx_load_seeprom(struct aic7xxx_host *p, unsigned char *sxfrctl1) -{ - int have_seeprom = 0; - int i, max_targets, mask; - unsigned char scsirate, scsi_conf; - unsigned short scarray[128]; - struct seeprom_config *sc = (struct seeprom_config *) scarray; - - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk(KERN_INFO "aic7xxx: Loading serial EEPROM..."); - } - switch (p->chip) - { - case (AHC_AIC7770|AHC_EISA): /* None of these adapters have seeproms. */ - if (aic_inb(p, SCSICONF) & TERM_ENB) - p->flags |= AHC_TERM_ENB_A; - if ( (p->features & AHC_TWIN) && (aic_inb(p, SCSICONF + 1) & TERM_ENB) ) - p->flags |= AHC_TERM_ENB_B; - break; - - case (AHC_AIC7770|AHC_VL): - have_seeprom = read_284x_seeprom(p, (struct seeprom_config *) scarray); - break; - - default: - have_seeprom = read_seeprom(p, (p->flags & (AHC_CHNLB|AHC_CHNLC)), - scarray, p->sc_size, p->sc_type); - if (!have_seeprom) - { - if(p->sc_type == C46) - have_seeprom = read_seeprom(p, (p->flags & (AHC_CHNLB|AHC_CHNLC)), - scarray, p->sc_size, C56_66); - else - have_seeprom = read_seeprom(p, (p->flags & (AHC_CHNLB|AHC_CHNLC)), - scarray, p->sc_size, C46); - } - if (!have_seeprom) - { - p->sc_size = 128; - have_seeprom = read_seeprom(p, 4*(p->flags & (AHC_CHNLB|AHC_CHNLC)), - scarray, p->sc_size, p->sc_type); - if (!have_seeprom) - { - if(p->sc_type == C46) - have_seeprom = read_seeprom(p, 4*(p->flags & (AHC_CHNLB|AHC_CHNLC)), - scarray, p->sc_size, C56_66); - else - have_seeprom = read_seeprom(p, 4*(p->flags & (AHC_CHNLB|AHC_CHNLC)), - scarray, p->sc_size, C46); - } - } - break; - } - - if (!have_seeprom) - { - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk("\naic7xxx: No SEEPROM available.\n"); - } - p->flags |= AHC_NEWEEPROM_FMT; - if (aic_inb(p, SCSISEQ) == 0) - { - p->flags |= AHC_USEDEFAULTS; - p->flags &= ~AHC_BIOS_ENABLED; - p->scsi_id = p->scsi_id_b = 7; - *sxfrctl1 |= STPWEN; - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk("aic7xxx: Using default values.\n"); - } - } - else if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk("aic7xxx: Using leftover BIOS values.\n"); - } - if ( ((p->chip & ~AHC_CHIPID_MASK) == AHC_PCI) && (*sxfrctl1 & STPWEN) ) - { - p->flags |= AHC_TERM_ENB_SE_LOW | AHC_TERM_ENB_SE_HIGH; - sc->adapter_control &= ~CFAUTOTERM; - sc->adapter_control |= CFSTERM | CFWSTERM | CFLVDSTERM; - } - if (aic7xxx_extended) - p->flags |= (AHC_EXTEND_TRANS_A | AHC_EXTEND_TRANS_B); - else - p->flags &= ~(AHC_EXTEND_TRANS_A | AHC_EXTEND_TRANS_B); - } - else - { - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk("done\n"); - } - - /* - * Note things in our flags - */ - p->flags |= AHC_SEEPROM_FOUND; - - /* - * Update the settings in sxfrctl1 to match the termination settings. - */ - *sxfrctl1 = 0; - - /* - * Get our SCSI ID from the SEEPROM setting... - */ - p->scsi_id = (sc->brtime_id & CFSCSIID); - - /* - * First process the settings that are different between the VLB - * and PCI adapter seeproms. - */ - if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7770) - { - /* VLB adapter seeproms */ - if (sc->bios_control & CF284XEXTEND) - p->flags |= AHC_EXTEND_TRANS_A; - - if (sc->adapter_control & CF284XSTERM) - { - *sxfrctl1 |= STPWEN; - p->flags |= AHC_TERM_ENB_SE_LOW | AHC_TERM_ENB_SE_HIGH; - } - } - else - { - /* PCI adapter seeproms */ - if (sc->bios_control & CFEXTEND) - p->flags |= AHC_EXTEND_TRANS_A; - if (sc->bios_control & CFBIOSEN) - p->flags |= AHC_BIOS_ENABLED; - else - p->flags &= ~AHC_BIOS_ENABLED; - - if (sc->adapter_control & CFSTERM) - { - *sxfrctl1 |= STPWEN; - p->flags |= AHC_TERM_ENB_SE_LOW | AHC_TERM_ENB_SE_HIGH; - } - } - memcpy(&p->sc, sc, sizeof(struct seeprom_config)); - } - - p->discenable = 0; - - /* - * Limit to 16 targets just in case. The 2842 for one is known to - * blow the max_targets setting, future cards might also. - */ - max_targets = ((p->features & (AHC_TWIN | AHC_WIDE)) ? 16 : 8); - - if (have_seeprom) - { - for (i = 0; i < max_targets; i++) - { - if( ((p->features & AHC_ULTRA) && - !(sc->adapter_control & CFULTRAEN) && - (sc->device_flags[i] & CFSYNCHISULTRA)) || - (sc->device_flags[i] & CFNEWULTRAFORMAT) ) - { - p->flags |= AHC_NEWEEPROM_FMT; - break; - } - } - } - - for (i = 0; i < max_targets; i++) - { - mask = (0x01 << i); - if (!have_seeprom) - { - if (aic_inb(p, SCSISEQ) != 0) - { - /* - * OK...the BIOS set things up and left behind the settings we need. - * Just make our sc->device_flags[i] entry match what the card has - * set for this device. - */ - p->discenable = - ~(aic_inb(p, DISC_DSB) | (aic_inb(p, DISC_DSB + 1) << 8) ); - p->ultraenb = - (aic_inb(p, ULTRA_ENB) | (aic_inb(p, ULTRA_ENB + 1) << 8) ); - sc->device_flags[i] = (p->discenable & mask) ? CFDISC : 0; - if (aic_inb(p, TARG_SCSIRATE + i) & WIDEXFER) - sc->device_flags[i] |= CFWIDEB; - if (p->features & AHC_ULTRA2) - { - if (aic_inb(p, TARG_OFFSET + i)) - { - sc->device_flags[i] |= CFSYNCH; - sc->device_flags[i] |= (aic_inb(p, TARG_SCSIRATE + i) & 0x07); - if ( (aic_inb(p, TARG_SCSIRATE + i) & 0x18) == 0x18 ) - sc->device_flags[i] |= CFSYNCHISULTRA; - } - } - else - { - if (aic_inb(p, TARG_SCSIRATE + i) & ~WIDEXFER) - { - sc->device_flags[i] |= CFSYNCH; - if (p->features & AHC_ULTRA) - sc->device_flags[i] |= ((p->ultraenb & mask) ? - CFSYNCHISULTRA : 0); - } - } - } - else - { - /* - * Assume the BIOS has NOT been run on this card and nothing between - * the card and the devices is configured yet. - */ - sc->device_flags[i] = CFDISC; - if (p->features & AHC_WIDE) - sc->device_flags[i] |= CFWIDEB; - if (p->features & AHC_ULTRA3) - sc->device_flags[i] |= 2; - else if (p->features & AHC_ULTRA2) - sc->device_flags[i] |= 3; - else if (p->features & AHC_ULTRA) - sc->device_flags[i] |= CFSYNCHISULTRA; - sc->device_flags[i] |= CFSYNCH; - aic_outb(p, 0, TARG_SCSIRATE + i); - if (p->features & AHC_ULTRA2) - aic_outb(p, 0, TARG_OFFSET + i); - } - } - if (sc->device_flags[i] & CFDISC) - { - p->discenable |= mask; - } - if (p->flags & AHC_NEWEEPROM_FMT) - { - if ( !(p->features & AHC_ULTRA2) ) - { - /* - * I know of two different Ultra BIOSes that do this differently. - * One on the Gigabyte 6BXU mb that wants flags[i] & CFXFER to - * be == to 0x03 and SYNCHISULTRA to be true to mean 40MByte/s - * while on the IBM Netfinity 5000 they want the same thing - * to be something else, while flags[i] & CFXFER == 0x03 and - * SYNCHISULTRA false should be 40MByte/s. So, we set both to - * 40MByte/s and the lower speeds be damned. People will have - * to select around the conversely mapped lower speeds in order - * to select lower speeds on these boards. - */ - if ( (sc->device_flags[i] & CFNEWULTRAFORMAT) && - ((sc->device_flags[i] & CFXFER) == 0x03) ) - { - sc->device_flags[i] &= ~CFXFER; - sc->device_flags[i] |= CFSYNCHISULTRA; - } - if (sc->device_flags[i] & CFSYNCHISULTRA) - { - p->ultraenb |= mask; - } - } - else if ( !(sc->device_flags[i] & CFNEWULTRAFORMAT) && - (p->features & AHC_ULTRA2) && - (sc->device_flags[i] & CFSYNCHISULTRA) ) - { - p->ultraenb |= mask; - } - } - else if (sc->adapter_control & CFULTRAEN) - { - p->ultraenb |= mask; - } - if ( (sc->device_flags[i] & CFSYNCH) == 0) - { - sc->device_flags[i] &= ~CFXFER; - p->ultraenb &= ~mask; - p->user[i].offset = 0; - p->user[i].period = 0; - p->user[i].options = 0; - } - else - { - if (p->features & AHC_ULTRA3) - { - p->user[i].offset = MAX_OFFSET_ULTRA2; - if( (sc->device_flags[i] & CFXFER) < 0x03 ) - { - scsirate = (sc->device_flags[i] & CFXFER); - p->user[i].options = MSG_EXT_PPR_OPTION_DT_CRC; - } - else - { - scsirate = (sc->device_flags[i] & CFXFER) | - ((p->ultraenb & mask) ? 0x18 : 0x10); - p->user[i].options = 0; - } - p->user[i].period = aic7xxx_find_period(p, scsirate, - AHC_SYNCRATE_ULTRA3); - } - else if (p->features & AHC_ULTRA2) - { - p->user[i].offset = MAX_OFFSET_ULTRA2; - scsirate = (sc->device_flags[i] & CFXFER) | - ((p->ultraenb & mask) ? 0x18 : 0x10); - p->user[i].options = 0; - p->user[i].period = aic7xxx_find_period(p, scsirate, - AHC_SYNCRATE_ULTRA2); - } - else - { - scsirate = (sc->device_flags[i] & CFXFER) << 4; - p->user[i].options = 0; - p->user[i].offset = MAX_OFFSET_8BIT; - if (p->features & AHC_ULTRA) - { - short ultraenb; - ultraenb = aic_inb(p, ULTRA_ENB) | - (aic_inb(p, ULTRA_ENB + 1) << 8); - p->user[i].period = aic7xxx_find_period(p, scsirate, - (p->ultraenb & mask) ? - AHC_SYNCRATE_ULTRA : - AHC_SYNCRATE_FAST); - } - else - p->user[i].period = aic7xxx_find_period(p, scsirate, - AHC_SYNCRATE_FAST); - } - } - if ( (sc->device_flags[i] & CFWIDEB) && (p->features & AHC_WIDE) ) - { - p->user[i].width = MSG_EXT_WDTR_BUS_16_BIT; - } - else - { - p->user[i].width = MSG_EXT_WDTR_BUS_8_BIT; - } - } - aic_outb(p, ~(p->discenable & 0xFF), DISC_DSB); - aic_outb(p, ~((p->discenable >> 8) & 0xFF), DISC_DSB + 1); - - /* - * We set the p->ultraenb from the SEEPROM to begin with, but now we make - * it match what is already down in the card. If we are doing a reset - * on the card then this will get put back to a default state anyway. - * This allows us to not have to pre-emptively negotiate when using the - * no_reset option. - */ - if (p->features & AHC_ULTRA) - p->ultraenb = aic_inb(p, ULTRA_ENB) | (aic_inb(p, ULTRA_ENB + 1) << 8); - - - scsi_conf = (p->scsi_id & HSCSIID); - - if(have_seeprom) - { - p->adapter_control = sc->adapter_control; - p->bios_control = sc->bios_control; - - switch (p->chip & AHC_CHIPID_MASK) - { - case AHC_AIC7895: - case AHC_AIC7896: - case AHC_AIC7899: - if (p->adapter_control & CFBPRIMARY) - p->flags |= AHC_CHANNEL_B_PRIMARY; - default: - break; - } - - if (sc->adapter_control & CFSPARITY) - scsi_conf |= ENSPCHK; - } - else - { - scsi_conf |= ENSPCHK | RESET_SCSI; - } - - /* - * Only set the SCSICONF and SCSICONF + 1 registers if we are a PCI card. - * The 2842 and 2742 cards already have these registers set and we don't - * want to muck with them since we don't set all the bits they do. - */ - if ( (p->chip & ~AHC_CHIPID_MASK) == AHC_PCI ) - { - /* Set the host ID */ - aic_outb(p, scsi_conf, SCSICONF); - /* In case we are a wide card */ - aic_outb(p, p->scsi_id, SCSICONF + 1); - } -} - -/*+F************************************************************************* - * Function: - * aic7xxx_configure_bugs - * - * Description: - * Take the card passed in and set the appropriate bug flags based upon - * the card model. Also make any changes needed to device registers or - * PCI registers while we are here. - *-F*************************************************************************/ -static void -aic7xxx_configure_bugs(struct aic7xxx_host *p) -{ - unsigned short tmp_word; - - switch(p->chip & AHC_CHIPID_MASK) - { - case AHC_AIC7860: - p->bugs |= AHC_BUG_PCI_2_1_RETRY; - /* fall through */ - case AHC_AIC7850: - case AHC_AIC7870: - p->bugs |= AHC_BUG_TMODE_WIDEODD | AHC_BUG_CACHETHEN | AHC_BUG_PCI_MWI; - break; - case AHC_AIC7880: - p->bugs |= AHC_BUG_TMODE_WIDEODD | AHC_BUG_PCI_2_1_RETRY | - AHC_BUG_CACHETHEN | AHC_BUG_PCI_MWI; - break; - case AHC_AIC7890: - p->bugs |= AHC_BUG_AUTOFLUSH | AHC_BUG_CACHETHEN; - break; - case AHC_AIC7892: - p->bugs |= AHC_BUG_SCBCHAN_UPLOAD; - break; - case AHC_AIC7895: - p->bugs |= AHC_BUG_TMODE_WIDEODD | AHC_BUG_PCI_2_1_RETRY | - AHC_BUG_CACHETHEN | AHC_BUG_PCI_MWI; - break; - case AHC_AIC7896: - p->bugs |= AHC_BUG_CACHETHEN_DIS; - break; - case AHC_AIC7899: - p->bugs |= AHC_BUG_SCBCHAN_UPLOAD; - break; - default: - /* Nothing to do */ - break; - } - - /* - * Now handle the bugs that require PCI register or card register tweaks - */ - pci_read_config_word(p->pdev, PCI_COMMAND, &tmp_word); - if(p->bugs & AHC_BUG_PCI_MWI) - { - tmp_word &= ~PCI_COMMAND_INVALIDATE; - } - else - { - tmp_word |= PCI_COMMAND_INVALIDATE; - } - pci_write_config_word(p->pdev, PCI_COMMAND, tmp_word); - - if(p->bugs & AHC_BUG_CACHETHEN) - { - aic_outb(p, aic_inb(p, DSCOMMAND0) & ~CACHETHEN, DSCOMMAND0); - } - else if (p->bugs & AHC_BUG_CACHETHEN_DIS) - { - aic_outb(p, aic_inb(p, DSCOMMAND0) | CACHETHEN, DSCOMMAND0); - } - - return; -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_detect - * - * Description: - * Try to detect and register an Adaptec 7770 or 7870 SCSI controller. - * - * XXX - This should really be called aic7xxx_probe(). A sequence of - * probe(), attach()/detach(), and init() makes more sense than - * one do-it-all function. This may be useful when (and if) the - * mid-level SCSI code is overhauled. - *-F*************************************************************************/ -static int -aic7xxx_detect(struct scsi_host_template *template) -{ - struct aic7xxx_host *temp_p = NULL; - struct aic7xxx_host *current_p = NULL; - struct aic7xxx_host *list_p = NULL; - int found = 0; -#if defined(__i386__) || defined(__alpha__) - ahc_flag_type flags = 0; - int type; -#endif - unsigned char sxfrctl1; -#if defined(__i386__) || defined(__alpha__) - unsigned char hcntrl, hostconf; - unsigned int slot, base; -#endif - -#ifdef MODULE - /* - * If we are called as a module, the aic7xxx pointer may not be null - * and it would point to our bootup string, just like on the lilo - * command line. IF not NULL, then process this config string with - * aic7xxx_setup - */ - if(aic7xxx) - aic7xxx_setup(aic7xxx); -#endif - - template->proc_name = "aic7xxx"; - template->sg_tablesize = AIC7XXX_MAX_SG; - - -#ifdef CONFIG_PCI - /* - * PCI-bus probe. - */ - { - static struct - { - unsigned short vendor_id; - unsigned short device_id; - ahc_chip chip; - ahc_flag_type flags; - ahc_feature features; - int board_name_index; - unsigned short seeprom_size; - unsigned short seeprom_type; - } const aic_pdevs[] = { - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7810, AHC_NONE, - AHC_FNONE, AHC_FENONE, 1, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7850, AHC_AIC7850, - AHC_PAGESCBS, AHC_AIC7850_FE, 5, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7855, AHC_AIC7850, - AHC_PAGESCBS, AHC_AIC7850_FE, 6, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7821, AHC_AIC7860, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7860_FE, 7, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_3860, AHC_AIC7860, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7860_FE, 7, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_38602, AHC_AIC7860, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7860_FE, 7, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_38602, AHC_AIC7860, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7860_FE, 7, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7860, AHC_AIC7860, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MOTHERBOARD, - AHC_AIC7860_FE, 7, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7861, AHC_AIC7860, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7860_FE, 8, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7870, AHC_AIC7870, - AHC_PAGESCBS | AHC_BIOS_ENABLED | AHC_MOTHERBOARD, - AHC_AIC7870_FE, 9, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7871, AHC_AIC7870, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7870_FE, 10, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7872, AHC_AIC7870, - AHC_PAGESCBS | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7870_FE, 11, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7873, AHC_AIC7870, - AHC_PAGESCBS | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7870_FE, 12, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7874, AHC_AIC7870, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7870_FE, 13, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7880, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED | AHC_MOTHERBOARD, - AHC_AIC7880_FE, 14, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7881, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7880_FE, 15, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7882, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7880_FE, 16, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7883, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7880_FE, 17, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7884, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7880_FE, 18, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7885, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7880_FE, 18, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7886, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7880_FE, 18, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7887, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7880_FE | AHC_NEW_AUTOTERM, 19, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7888, AHC_AIC7880, - AHC_PAGESCBS | AHC_BIOS_ENABLED, AHC_AIC7880_FE, 18, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_7895, AHC_AIC7895, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7895_FE, 20, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7890, AHC_AIC7890, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7890_FE, 21, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7890B, AHC_AIC7890, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7890_FE, 21, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_2930U2, AHC_AIC7890, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7890_FE, 22, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_2940U2, AHC_AIC7890, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7890_FE, 23, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7896, AHC_AIC7896, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7896_FE, 24, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_3940U2, AHC_AIC7896, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7896_FE, 25, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_3950U2D, AHC_AIC7896, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7896_FE, 26, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC, PCI_DEVICE_ID_ADAPTEC_1480A, AHC_AIC7860, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_NO_STPWEN, - AHC_AIC7860_FE, 27, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7892A, AHC_AIC7892, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7892_FE, 28, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7892B, AHC_AIC7892, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7892_FE, 28, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7892D, AHC_AIC7892, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7892_FE, 28, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7892P, AHC_AIC7892, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED, - AHC_AIC7892_FE, 28, - 32, C46 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7899A, AHC_AIC7899, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7899_FE, 29, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7899B, AHC_AIC7899, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7899_FE, 29, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7899D, AHC_AIC7899, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7899_FE, 29, - 32, C56_66 }, - {PCI_VENDOR_ID_ADAPTEC2, PCI_DEVICE_ID_ADAPTEC2_7899P, AHC_AIC7899, - AHC_PAGESCBS | AHC_NEWEEPROM_FMT | AHC_BIOS_ENABLED | AHC_MULTI_CHANNEL, - AHC_AIC7899_FE, 29, - 32, C56_66 }, - }; - - unsigned short command; - unsigned int devconfig, i, oldverbose; - struct pci_dev *pdev = NULL; - - for (i = 0; i < ARRAY_SIZE(aic_pdevs); i++) - { - pdev = NULL; - while ((pdev = pci_get_device(aic_pdevs[i].vendor_id, - aic_pdevs[i].device_id, - pdev))) { - if (pci_enable_device(pdev)) - continue; - if ( i == 0 ) /* We found one, but it's the 7810 RAID cont. */ - { - if (aic7xxx_verbose & (VERBOSE_PROBE|VERBOSE_PROBE2)) - { - printk(KERN_INFO "aic7xxx: The 7810 RAID controller is not " - "supported by\n"); - printk(KERN_INFO " this driver, we are ignoring it.\n"); - } - } - else if ( (temp_p = kzalloc(sizeof(struct aic7xxx_host), - GFP_ATOMIC)) != NULL ) - { - temp_p->chip = aic_pdevs[i].chip | AHC_PCI; - temp_p->flags = aic_pdevs[i].flags; - temp_p->features = aic_pdevs[i].features; - temp_p->board_name_index = aic_pdevs[i].board_name_index; - temp_p->sc_size = aic_pdevs[i].seeprom_size; - temp_p->sc_type = aic_pdevs[i].seeprom_type; - - /* - * Read sundry information from PCI BIOS. - */ - temp_p->irq = pdev->irq; - temp_p->pdev = pdev; - temp_p->pci_bus = pdev->bus->number; - temp_p->pci_device_fn = pdev->devfn; - temp_p->base = pci_resource_start(pdev, 0); - temp_p->mbase = pci_resource_start(pdev, 1); - current_p = list_p; - while(current_p && temp_p) - { - if ( ((current_p->pci_bus == temp_p->pci_bus) && - (current_p->pci_device_fn == temp_p->pci_device_fn)) || - (temp_p->base && (current_p->base == temp_p->base)) || - (temp_p->mbase && (current_p->mbase == temp_p->mbase)) ) - { - /* duplicate PCI entry, skip it */ - kfree(temp_p); - temp_p = NULL; - continue; - } - current_p = current_p->next; - } - if(pci_request_regions(temp_p->pdev, "aic7xxx")) - { - printk("aic7xxx: <%s> at PCI %d/%d/%d\n", - board_names[aic_pdevs[i].board_name_index], - temp_p->pci_bus, - PCI_SLOT(temp_p->pci_device_fn), - PCI_FUNC(temp_p->pci_device_fn)); - printk("aic7xxx: I/O ports already in use, ignoring.\n"); - kfree(temp_p); - continue; - } - - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk("aic7xxx: <%s> at PCI %d/%d\n", - board_names[aic_pdevs[i].board_name_index], - PCI_SLOT(pdev->devfn), - PCI_FUNC(pdev->devfn)); - pci_read_config_word(pdev, PCI_COMMAND, &command); - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk("aic7xxx: Initial PCI_COMMAND value was 0x%x\n", - (int)command); - } -#ifdef AIC7XXX_STRICT_PCI_SETUP - command |= PCI_COMMAND_SERR | PCI_COMMAND_PARITY | - PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO; -#else - command |= PCI_COMMAND_MASTER | PCI_COMMAND_MEMORY | PCI_COMMAND_IO; -#endif - command &= ~PCI_COMMAND_INVALIDATE; - if (aic7xxx_pci_parity == 0) - command &= ~(PCI_COMMAND_SERR | PCI_COMMAND_PARITY); - pci_write_config_word(pdev, PCI_COMMAND, command); -#ifdef AIC7XXX_STRICT_PCI_SETUP - pci_read_config_dword(pdev, DEVCONFIG, &devconfig); - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk("aic7xxx: Initial DEVCONFIG value was 0x%x\n", devconfig); - } - devconfig |= 0x80000040; - pci_write_config_dword(pdev, DEVCONFIG, devconfig); -#endif /* AIC7XXX_STRICT_PCI_SETUP */ - - temp_p->unpause = INTEN; - temp_p->pause = temp_p->unpause | PAUSE; - if ( ((temp_p->base == 0) && - (temp_p->mbase == 0)) || - (temp_p->irq == 0) ) - { - printk("aic7xxx: <%s> at PCI %d/%d/%d\n", - board_names[aic_pdevs[i].board_name_index], - temp_p->pci_bus, - PCI_SLOT(temp_p->pci_device_fn), - PCI_FUNC(temp_p->pci_device_fn)); - printk("aic7xxx: Controller disabled by BIOS, ignoring.\n"); - goto skip_pci_controller; - } - -#ifdef MMAPIO - if ( !(temp_p->base) || !(temp_p->flags & AHC_MULTI_CHANNEL) || - ((temp_p->chip != (AHC_AIC7870 | AHC_PCI)) && - (temp_p->chip != (AHC_AIC7880 | AHC_PCI))) ) - { - temp_p->maddr = ioremap_nocache(temp_p->mbase, 256); - if(temp_p->maddr) - { - /* - * We need to check the I/O with the MMAPed address. Some machines - * simply fail to work with MMAPed I/O and certain controllers. - */ - if(aic_inb(temp_p, HCNTRL) == 0xff) - { - /* - * OK.....we failed our test....go back to programmed I/O - */ - printk(KERN_INFO "aic7xxx: <%s> at PCI %d/%d/%d\n", - board_names[aic_pdevs[i].board_name_index], - temp_p->pci_bus, - PCI_SLOT(temp_p->pci_device_fn), - PCI_FUNC(temp_p->pci_device_fn)); - printk(KERN_INFO "aic7xxx: MMAPed I/O failed, reverting to " - "Programmed I/O.\n"); - iounmap(temp_p->maddr); - temp_p->maddr = NULL; - if(temp_p->base == 0) - { - printk("aic7xxx: <%s> at PCI %d/%d/%d\n", - board_names[aic_pdevs[i].board_name_index], - temp_p->pci_bus, - PCI_SLOT(temp_p->pci_device_fn), - PCI_FUNC(temp_p->pci_device_fn)); - printk("aic7xxx: Controller disabled by BIOS, ignoring.\n"); - goto skip_pci_controller; - } - } - } - } -#endif - - /* - * We HAVE to make sure the first pause_sequencer() and all other - * subsequent I/O that isn't PCI config space I/O takes place - * after the MMAPed I/O region is configured and tested. The - * problem is the PowerPC architecture that doesn't support - * programmed I/O at all, so we have to have the MMAP I/O set up - * for this pause to even work on those machines. - */ - pause_sequencer(temp_p); - - /* - * Clear out any pending PCI error status messages. Also set - * verbose to 0 so that we don't emit strange PCI error messages - * while cleaning out the current status bits. - */ - oldverbose = aic7xxx_verbose; - aic7xxx_verbose = 0; - aic7xxx_pci_intr(temp_p); - aic7xxx_verbose = oldverbose; - - temp_p->bios_address = 0; - - /* - * Remember how the card was setup in case there is no seeprom. - */ - if (temp_p->features & AHC_ULTRA2) - temp_p->scsi_id = aic_inb(temp_p, SCSIID_ULTRA2) & OID; - else - temp_p->scsi_id = aic_inb(temp_p, SCSIID) & OID; - /* - * Get current termination setting - */ - sxfrctl1 = aic_inb(temp_p, SXFRCTL1); - - if (aic7xxx_chip_reset(temp_p) == -1) - { - goto skip_pci_controller; - } - /* - * Very quickly put the term setting back into the register since - * the chip reset may cause odd things to happen. This is to keep - * LVD busses with lots of drives from draining the power out of - * the diffsense line before we get around to running the - * configure_termination() function. Also restore the STPWLEVEL - * bit of DEVCONFIG - */ - aic_outb(temp_p, sxfrctl1, SXFRCTL1); - pci_write_config_dword(temp_p->pdev, DEVCONFIG, devconfig); - sxfrctl1 &= STPWEN; - - /* - * We need to set the CHNL? assignments before loading the SEEPROM - * The 3940 and 3985 cards (original stuff, not any of the later - * stuff) are 7870 and 7880 class chips. The Ultra2 stuff falls - * under 7896 and 7897. The 7895 is in a class by itself :) - */ - switch (temp_p->chip & AHC_CHIPID_MASK) - { - case AHC_AIC7870: /* 3840 / 3985 */ - case AHC_AIC7880: /* 3840 UW / 3985 UW */ - if(temp_p->flags & AHC_MULTI_CHANNEL) - { - switch(PCI_SLOT(temp_p->pci_device_fn)) - { - case 5: - temp_p->flags |= AHC_CHNLB; - break; - case 8: - temp_p->flags |= AHC_CHNLB; - break; - case 12: - temp_p->flags |= AHC_CHNLC; - break; - default: - break; - } - } - break; - - case AHC_AIC7895: /* 7895 */ - case AHC_AIC7896: /* 7896/7 */ - case AHC_AIC7899: /* 7899 */ - if (PCI_FUNC(pdev->devfn) != 0) - { - temp_p->flags |= AHC_CHNLB; - } - /* - * The 7895 is the only chipset that sets the SCBSIZE32 param - * in the DEVCONFIG register. The Ultra2 chipsets use - * the DSCOMMAND0 register instead. - */ - if ((temp_p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) - { - pci_read_config_dword(pdev, DEVCONFIG, &devconfig); - devconfig |= SCBSIZE32; - pci_write_config_dword(pdev, DEVCONFIG, devconfig); - } - break; - default: - break; - } - - /* - * Loading of the SEEPROM needs to come after we've set the flags - * to indicate possible CHNLB and CHNLC assigments. Otherwise, - * on 394x and 398x cards we'll end up reading the wrong settings - * for channels B and C - */ - switch (temp_p->chip & AHC_CHIPID_MASK) - { - case AHC_AIC7892: - case AHC_AIC7899: - aic_outb(temp_p, 0, SCAMCTL); - /* - * Switch to the alt mode of the chip... - */ - aic_outb(temp_p, aic_inb(temp_p, SFUNCT) | ALT_MODE, SFUNCT); - /* - * Set our options...the last two items set our CRC after x byte - * count in target mode... - */ - aic_outb(temp_p, AUTO_MSGOUT_DE | DIS_MSGIN_DUALEDGE, OPTIONMODE); - aic_outb(temp_p, 0x00, 0x0b); - aic_outb(temp_p, 0x10, 0x0a); - /* - * switch back to normal mode... - */ - aic_outb(temp_p, aic_inb(temp_p, SFUNCT) & ~ALT_MODE, SFUNCT); - aic_outb(temp_p, CRCVALCHKEN | CRCENDCHKEN | CRCREQCHKEN | - TARGCRCENDEN | TARGCRCCNTEN, - CRCCONTROL1); - aic_outb(temp_p, ((aic_inb(temp_p, DSCOMMAND0) | USCBSIZE32 | - MPARCKEN | CIOPARCKEN | CACHETHEN) & - ~DPARCKEN), DSCOMMAND0); - aic7xxx_load_seeprom(temp_p, &sxfrctl1); - break; - case AHC_AIC7890: - case AHC_AIC7896: - aic_outb(temp_p, 0, SCAMCTL); - aic_outb(temp_p, (aic_inb(temp_p, DSCOMMAND0) | - CACHETHEN | MPARCKEN | USCBSIZE32 | - CIOPARCKEN) & ~DPARCKEN, DSCOMMAND0); - aic7xxx_load_seeprom(temp_p, &sxfrctl1); - break; - case AHC_AIC7850: - case AHC_AIC7860: - /* - * Set the DSCOMMAND0 register on these cards different from - * on the 789x cards. Also, read the SEEPROM as well. - */ - aic_outb(temp_p, (aic_inb(temp_p, DSCOMMAND0) | - CACHETHEN | MPARCKEN) & ~DPARCKEN, - DSCOMMAND0); - /* FALLTHROUGH */ - default: - aic7xxx_load_seeprom(temp_p, &sxfrctl1); - break; - case AHC_AIC7880: - /* - * Check the rev of the chipset before we change DSCOMMAND0 - */ - pci_read_config_dword(pdev, DEVCONFIG, &devconfig); - if ((devconfig & 0xff) >= 1) - { - aic_outb(temp_p, (aic_inb(temp_p, DSCOMMAND0) | - CACHETHEN | MPARCKEN) & ~DPARCKEN, - DSCOMMAND0); - } - aic7xxx_load_seeprom(temp_p, &sxfrctl1); - break; - } - - - /* - * and then we need another switch based on the type in order to - * make sure the channel B primary flag is set properly on 7895 - * controllers....Arrrgggghhh!!! We also have to catch the fact - * that when you disable the BIOS on the 7895 on the Intel DK440LX - * motherboard, and possibly others, it only sets the BIOS disabled - * bit on the A channel...I think I'm starting to lean towards - * going postal.... - */ - switch(temp_p->chip & AHC_CHIPID_MASK) - { - case AHC_AIC7895: - case AHC_AIC7896: - case AHC_AIC7899: - current_p = list_p; - while(current_p != NULL) - { - if ( (current_p->pci_bus == temp_p->pci_bus) && - (PCI_SLOT(current_p->pci_device_fn) == - PCI_SLOT(temp_p->pci_device_fn)) ) - { - if ( PCI_FUNC(current_p->pci_device_fn) == 0 ) - { - temp_p->flags |= - (current_p->flags & AHC_CHANNEL_B_PRIMARY); - temp_p->flags &= ~(AHC_BIOS_ENABLED|AHC_USEDEFAULTS); - temp_p->flags |= - (current_p->flags & (AHC_BIOS_ENABLED|AHC_USEDEFAULTS)); - } - else - { - current_p->flags |= - (temp_p->flags & AHC_CHANNEL_B_PRIMARY); - current_p->flags &= ~(AHC_BIOS_ENABLED|AHC_USEDEFAULTS); - current_p->flags |= - (temp_p->flags & (AHC_BIOS_ENABLED|AHC_USEDEFAULTS)); - } - } - current_p = current_p->next; - } - break; - default: - break; - } - - /* - * We only support external SCB RAM on the 7895/6/7 chipsets. - * We could support it on the 7890/1 easy enough, but I don't - * know of any 7890/1 based cards that have it. I do know - * of 7895/6/7 cards that have it and they work properly. - */ - switch(temp_p->chip & AHC_CHIPID_MASK) - { - default: - break; - case AHC_AIC7895: - case AHC_AIC7896: - case AHC_AIC7899: - pci_read_config_dword(pdev, DEVCONFIG, &devconfig); - if (temp_p->features & AHC_ULTRA2) - { - if ( (aic_inb(temp_p, DSCOMMAND0) & RAMPSM_ULTRA2) && - (aic7xxx_scbram) ) - { - aic_outb(temp_p, - aic_inb(temp_p, DSCOMMAND0) & ~SCBRAMSEL_ULTRA2, - DSCOMMAND0); - temp_p->flags |= AHC_EXTERNAL_SRAM; - devconfig |= EXTSCBPEN; - } - else if (aic_inb(temp_p, DSCOMMAND0) & RAMPSM_ULTRA2) - { - printk(KERN_INFO "aic7xxx: <%s> at PCI %d/%d/%d\n", - board_names[aic_pdevs[i].board_name_index], - temp_p->pci_bus, - PCI_SLOT(temp_p->pci_device_fn), - PCI_FUNC(temp_p->pci_device_fn)); - printk("aic7xxx: external SCB RAM detected, " - "but not enabled\n"); - } - } - else - { - if ((devconfig & RAMPSM) && (aic7xxx_scbram)) - { - devconfig &= ~SCBRAMSEL; - devconfig |= EXTSCBPEN; - temp_p->flags |= AHC_EXTERNAL_SRAM; - } - else if (devconfig & RAMPSM) - { - printk(KERN_INFO "aic7xxx: <%s> at PCI %d/%d/%d\n", - board_names[aic_pdevs[i].board_name_index], - temp_p->pci_bus, - PCI_SLOT(temp_p->pci_device_fn), - PCI_FUNC(temp_p->pci_device_fn)); - printk("aic7xxx: external SCB RAM detected, " - "but not enabled\n"); - } - } - pci_write_config_dword(pdev, DEVCONFIG, devconfig); - if ( (temp_p->flags & AHC_EXTERNAL_SRAM) && - (temp_p->flags & AHC_CHNLB) ) - aic_outb(temp_p, 1, CCSCBBADDR); - break; - } - - /* - * Take the LED out of diagnostic mode - */ - aic_outb(temp_p, - (aic_inb(temp_p, SBLKCTL) & ~(DIAGLEDEN | DIAGLEDON)), - SBLKCTL); - - /* - * We don't know where this is set in the SEEPROM or by the - * BIOS, so we default to 100%. On Ultra2 controllers, use 75% - * instead. - */ - if (temp_p->features & AHC_ULTRA2) - { - aic_outb(temp_p, RD_DFTHRSH_MAX | WR_DFTHRSH_MAX, DFF_THRSH); - } - else - { - aic_outb(temp_p, DFTHRSH_100, DSPCISTATUS); - } - - /* - * Call our function to fixup any bugs that exist on this chipset. - * This may muck with PCI settings and other device settings, so - * make sure it's after all the other PCI and device register - * tweaks so it can back out bad settings on specific broken cards. - */ - aic7xxx_configure_bugs(temp_p); - - /* Hold a pci device reference */ - pci_dev_get(temp_p->pdev); - - if ( list_p == NULL ) - { - list_p = current_p = temp_p; - } - else - { - current_p = list_p; - while(current_p->next != NULL) - current_p = current_p->next; - current_p->next = temp_p; - } - temp_p->next = NULL; - found++; - continue; -skip_pci_controller: -#ifdef CONFIG_PCI - pci_release_regions(temp_p->pdev); -#endif - kfree(temp_p); - } /* Found an Adaptec PCI device. */ - else /* Well, we found one, but we couldn't get any memory */ - { - printk("aic7xxx: Found <%s>\n", - board_names[aic_pdevs[i].board_name_index]); - printk(KERN_INFO "aic7xxx: Unable to allocate device memory, " - "skipping.\n"); - } - } /* while(pdev=....) */ - } /* for PCI_DEVICES */ - } -#endif /* CONFIG_PCI */ - -#if defined(__i386__) || defined(__alpha__) - /* - * EISA/VL-bus card signature probe. - */ - slot = MINSLOT; - while ( (slot <= MAXSLOT) && - !(aic7xxx_no_probe) ) - { - base = SLOTBASE(slot) + MINREG; - - if (!request_region(base, MAXREG - MINREG, "aic7xxx")) - { - /* - * Some other driver has staked a - * claim to this i/o region already. - */ - slot++; - continue; /* back to the beginning of the for loop */ - } - flags = 0; - type = aic7xxx_probe(slot, base + AHC_HID0, &flags); - if (type == -1) - { - release_region(base, MAXREG - MINREG); - slot++; - continue; - } - temp_p = kmalloc(sizeof(struct aic7xxx_host), GFP_ATOMIC); - if (temp_p == NULL) - { - printk(KERN_WARNING "aic7xxx: Unable to allocate device space.\n"); - release_region(base, MAXREG - MINREG); - slot++; - continue; /* back to the beginning of the while loop */ - } - - /* - * Pause the card preserving the IRQ type. Allow the operator - * to override the IRQ trigger. - */ - if (aic7xxx_irq_trigger == 1) - hcntrl = IRQMS; /* Level */ - else if (aic7xxx_irq_trigger == 0) - hcntrl = 0; /* Edge */ - else - hcntrl = inb(base + HCNTRL) & IRQMS; /* Default */ - memset(temp_p, 0, sizeof(struct aic7xxx_host)); - temp_p->unpause = hcntrl | INTEN; - temp_p->pause = hcntrl | PAUSE | INTEN; - temp_p->base = base; - temp_p->mbase = 0; - temp_p->maddr = NULL; - temp_p->pci_bus = 0; - temp_p->pci_device_fn = slot; - aic_outb(temp_p, hcntrl | PAUSE, HCNTRL); - while( (aic_inb(temp_p, HCNTRL) & PAUSE) == 0 ) ; - if (aic7xxx_chip_reset(temp_p) == -1) - temp_p->irq = 0; - else - temp_p->irq = aic_inb(temp_p, INTDEF) & 0x0F; - temp_p->flags |= AHC_PAGESCBS; - - switch (temp_p->irq) - { - case 9: - case 10: - case 11: - case 12: - case 14: - case 15: - break; - - default: - printk(KERN_WARNING "aic7xxx: Host adapter uses unsupported IRQ " - "level %d, ignoring.\n", temp_p->irq); - kfree(temp_p); - release_region(base, MAXREG - MINREG); - slot++; - continue; /* back to the beginning of the while loop */ - } - - /* - * We are committed now, everything has been checked and this card - * has been found, now we just set it up - */ - - /* - * Insert our new struct into the list at the end - */ - if (list_p == NULL) - { - list_p = current_p = temp_p; - } - else - { - current_p = list_p; - while (current_p->next != NULL) - current_p = current_p->next; - current_p->next = temp_p; - } - - switch (type) - { - case 0: - temp_p->board_name_index = 2; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk("aic7xxx: <%s> at EISA %d\n", - board_names[2], slot); - /* FALLTHROUGH */ - case 1: - { - temp_p->chip = AHC_AIC7770 | AHC_EISA; - temp_p->features |= AHC_AIC7770_FE; - temp_p->bios_control = aic_inb(temp_p, HA_274_BIOSCTRL); - - /* - * Get the primary channel information. Right now we don't - * do anything with this, but someday we will be able to inform - * the mid-level SCSI code which channel is primary. - */ - if (temp_p->board_name_index == 0) - { - temp_p->board_name_index = 3; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk("aic7xxx: <%s> at EISA %d\n", - board_names[3], slot); - } - if (temp_p->bios_control & CHANNEL_B_PRIMARY) - { - temp_p->flags |= AHC_CHANNEL_B_PRIMARY; - } - - if ((temp_p->bios_control & BIOSMODE) == BIOSDISABLED) - { - temp_p->flags &= ~AHC_BIOS_ENABLED; - } - else - { - temp_p->flags &= ~AHC_USEDEFAULTS; - temp_p->flags |= AHC_BIOS_ENABLED; - if ( (temp_p->bios_control & 0x20) == 0 ) - { - temp_p->bios_address = 0xcc000; - temp_p->bios_address += (0x4000 * (temp_p->bios_control & 0x07)); - } - else - { - temp_p->bios_address = 0xd0000; - temp_p->bios_address += (0x8000 * (temp_p->bios_control & 0x06)); - } - } - temp_p->adapter_control = aic_inb(temp_p, SCSICONF) << 8; - temp_p->adapter_control |= aic_inb(temp_p, SCSICONF + 1); - if (temp_p->features & AHC_WIDE) - { - temp_p->scsi_id = temp_p->adapter_control & HWSCSIID; - temp_p->scsi_id_b = temp_p->scsi_id; - } - else - { - temp_p->scsi_id = (temp_p->adapter_control >> 8) & HSCSIID; - temp_p->scsi_id_b = temp_p->adapter_control & HSCSIID; - } - aic7xxx_load_seeprom(temp_p, &sxfrctl1); - break; - } - - case 2: - case 3: - temp_p->chip = AHC_AIC7770 | AHC_VL; - temp_p->features |= AHC_AIC7770_FE; - if (type == 2) - temp_p->flags |= AHC_BIOS_ENABLED; - else - temp_p->flags &= ~AHC_BIOS_ENABLED; - if (aic_inb(temp_p, SCSICONF) & TERM_ENB) - sxfrctl1 = STPWEN; - aic7xxx_load_seeprom(temp_p, &sxfrctl1); - temp_p->board_name_index = 4; - if (aic7xxx_verbose & VERBOSE_PROBE2) - printk("aic7xxx: <%s> at VLB %d\n", - board_names[2], slot); - switch( aic_inb(temp_p, STATUS_2840) & BIOS_SEL ) - { - case 0x00: - temp_p->bios_address = 0xe0000; - break; - case 0x20: - temp_p->bios_address = 0xc8000; - break; - case 0x40: - temp_p->bios_address = 0xd0000; - break; - case 0x60: - temp_p->bios_address = 0xd8000; - break; - default: - break; /* can't get here */ - } - break; - - default: /* Won't get here. */ - break; - } - if (aic7xxx_verbose & VERBOSE_PROBE2) - { - printk(KERN_INFO "aic7xxx: BIOS %sabled, IO Port 0x%lx, IRQ %d (%s)\n", - (temp_p->flags & AHC_USEDEFAULTS) ? "dis" : "en", temp_p->base, - temp_p->irq, - (temp_p->pause & IRQMS) ? "level sensitive" : "edge triggered"); - printk(KERN_INFO "aic7xxx: Extended translation %sabled.\n", - (temp_p->flags & AHC_EXTEND_TRANS_A) ? "en" : "dis"); - } - - /* - * All the 7770 based chipsets have this bug - */ - temp_p->bugs |= AHC_BUG_TMODE_WIDEODD; - - /* - * Set the FIFO threshold and the bus off time. - */ - hostconf = aic_inb(temp_p, HOSTCONF); - aic_outb(temp_p, hostconf & DFTHRSH, BUSSPD); - aic_outb(temp_p, (hostconf << 2) & BOFF, BUSTIME); - slot++; - found++; - } - -#endif /* defined(__i386__) || defined(__alpha__) */ - - /* - * Now, we re-order the probed devices by BIOS address and BUS class. - * In general, we follow this algorithm to make the adapters show up - * in the same order under linux that the computer finds them. - * 1: All VLB/EISA cards with BIOS_ENABLED first, according to BIOS - * address, going from lowest to highest. - * 2: All PCI controllers with BIOS_ENABLED next, according to BIOS - * address, going from lowest to highest. - * 3: Remaining VLB/EISA controllers going in slot order. - * 4: Remaining PCI controllers, going in PCI device order (reversible) - */ - - { - struct aic7xxx_host *sort_list[4] = { NULL, NULL, NULL, NULL }; - struct aic7xxx_host *vlb, *pci; - struct aic7xxx_host *prev_p; - struct aic7xxx_host *p; - unsigned char left; - - prev_p = vlb = pci = NULL; - - temp_p = list_p; - while (temp_p != NULL) - { - switch(temp_p->chip & ~AHC_CHIPID_MASK) - { - case AHC_EISA: - case AHC_VL: - { - p = temp_p; - if (p->flags & AHC_BIOS_ENABLED) - vlb = sort_list[0]; - else - vlb = sort_list[2]; - - if (vlb == NULL) - { - vlb = temp_p; - temp_p = temp_p->next; - vlb->next = NULL; - } - else - { - current_p = vlb; - prev_p = NULL; - while ( (current_p != NULL) && - (current_p->bios_address < temp_p->bios_address)) - { - prev_p = current_p; - current_p = current_p->next; - } - if (prev_p != NULL) - { - prev_p->next = temp_p; - temp_p = temp_p->next; - prev_p->next->next = current_p; - } - else - { - vlb = temp_p; - temp_p = temp_p->next; - vlb->next = current_p; - } - } - - if (p->flags & AHC_BIOS_ENABLED) - sort_list[0] = vlb; - else - sort_list[2] = vlb; - - break; - } - default: /* All PCI controllers fall through to default */ - { - - p = temp_p; - if (p->flags & AHC_BIOS_ENABLED) - pci = sort_list[1]; - else - pci = sort_list[3]; - - if (pci == NULL) - { - pci = temp_p; - temp_p = temp_p->next; - pci->next = NULL; - } - else - { - current_p = pci; - prev_p = NULL; - if (!aic7xxx_reverse_scan) - { - while ( (current_p != NULL) && - ( (PCI_SLOT(current_p->pci_device_fn) | - (current_p->pci_bus << 8)) < - (PCI_SLOT(temp_p->pci_device_fn) | - (temp_p->pci_bus << 8)) ) ) - { - prev_p = current_p; - current_p = current_p->next; - } - } - else - { - while ( (current_p != NULL) && - ( (PCI_SLOT(current_p->pci_device_fn) | - (current_p->pci_bus << 8)) > - (PCI_SLOT(temp_p->pci_device_fn) | - (temp_p->pci_bus << 8)) ) ) - { - prev_p = current_p; - current_p = current_p->next; - } - } - /* - * Are we dealing with a 7895/6/7/9 where we need to sort the - * channels as well, if so, the bios_address values should - * be the same - */ - if ( (current_p) && (temp_p->flags & AHC_MULTI_CHANNEL) && - (temp_p->pci_bus == current_p->pci_bus) && - (PCI_SLOT(temp_p->pci_device_fn) == - PCI_SLOT(current_p->pci_device_fn)) ) - { - if (temp_p->flags & AHC_CHNLB) - { - if ( !(temp_p->flags & AHC_CHANNEL_B_PRIMARY) ) - { - prev_p = current_p; - current_p = current_p->next; - } - } - else - { - if (temp_p->flags & AHC_CHANNEL_B_PRIMARY) - { - prev_p = current_p; - current_p = current_p->next; - } - } - } - if (prev_p != NULL) - { - prev_p->next = temp_p; - temp_p = temp_p->next; - prev_p->next->next = current_p; - } - else - { - pci = temp_p; - temp_p = temp_p->next; - pci->next = current_p; - } - } - - if (p->flags & AHC_BIOS_ENABLED) - sort_list[1] = pci; - else - sort_list[3] = pci; - - break; - } - } /* End of switch(temp_p->type) */ - } /* End of while (temp_p != NULL) */ - /* - * At this point, the cards have been broken into 4 sorted lists, now - * we run through the lists in order and register each controller - */ - { - int i; - - left = found; - for (i=0; i<ARRAY_SIZE(sort_list); i++) - { - temp_p = sort_list[i]; - while(temp_p != NULL) - { - template->name = board_names[temp_p->board_name_index]; - p = aic7xxx_alloc(template, temp_p); - if (p != NULL) - { - p->instance = found - left; - if (aic7xxx_register(template, p, (--left)) == 0) - { - found--; - aic7xxx_release(p->host); - scsi_unregister(p->host); - } - else if (aic7xxx_dump_card) - { - pause_sequencer(p); - aic7xxx_print_card(p); - aic7xxx_print_scratch_ram(p); - unpause_sequencer(p, TRUE); - } - } - current_p = temp_p; - temp_p = (struct aic7xxx_host *)temp_p->next; - kfree(current_p); - } - } - } - } - return (found); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_buildscb - * - * Description: - * Build a SCB. - *-F*************************************************************************/ -static void aic7xxx_buildscb(struct aic7xxx_host *p, struct scsi_cmnd *cmd, - struct aic7xxx_scb *scb) -{ - unsigned short mask; - struct aic7xxx_hwscb *hscb; - struct aic_dev_data *aic_dev = cmd->device->hostdata; - struct scsi_device *sdptr = cmd->device; - unsigned char tindex = TARGET_INDEX(cmd); - int use_sg; - - mask = (0x01 << tindex); - hscb = scb->hscb; - - /* - * Setup the control byte if we need negotiation and have not - * already requested it. - */ - hscb->control = 0; - scb->tag_action = 0; - - if (p->discenable & mask) - { - hscb->control |= DISCENB; - /* We always force TEST_UNIT_READY to untagged */ - if (cmd->cmnd[0] != TEST_UNIT_READY && sdptr->simple_tags) - { - hscb->control |= MSG_SIMPLE_Q_TAG; - scb->tag_action = MSG_SIMPLE_Q_TAG; - } - } - if ( !(aic_dev->dtr_pending) && - (aic_dev->needppr || aic_dev->needwdtr || aic_dev->needsdtr) && - (aic_dev->flags & DEVICE_DTR_SCANNED) ) - { - aic_dev->dtr_pending = 1; - scb->tag_action = 0; - hscb->control &= DISCENB; - hscb->control |= MK_MESSAGE; - if(aic_dev->needppr) - { - scb->flags |= SCB_MSGOUT_PPR; - } - else if(aic_dev->needwdtr) - { - scb->flags |= SCB_MSGOUT_WDTR; - } - else if(aic_dev->needsdtr) - { - scb->flags |= SCB_MSGOUT_SDTR; - } - scb->flags |= SCB_DTR_SCB; - } - hscb->target_channel_lun = ((cmd->device->id << 4) & 0xF0) | - ((cmd->device->channel & 0x01) << 3) | (cmd->device->lun & 0x07); - - /* - * The interpretation of request_buffer and request_bufflen - * changes depending on whether or not use_sg is zero; a - * non-zero use_sg indicates the number of elements in the - * scatter-gather array. - */ - - /* - * XXX - this relies on the host data being stored in a - * little-endian format. - */ - hscb->SCSI_cmd_length = cmd->cmd_len; - memcpy(scb->cmnd, cmd->cmnd, cmd->cmd_len); - hscb->SCSI_cmd_pointer = cpu_to_le32(SCB_DMA_ADDR(scb, scb->cmnd)); - - use_sg = scsi_dma_map(cmd); - BUG_ON(use_sg < 0); - - if (use_sg) { - struct scatterlist *sg; /* Must be mid-level SCSI code scatterlist */ - - /* - * We must build an SG list in adapter format, as the kernel's SG list - * cannot be used directly because of data field size (__alpha__) - * differences and the kernel SG list uses virtual addresses where - * we need physical addresses. - */ - int i; - - scb->sg_length = 0; - - - /* - * Copy the segments into the SG array. NOTE!!! - We used to - * have the first entry both in the data_pointer area and the first - * SG element. That has changed somewhat. We still have the first - * entry in both places, but now we download the address of - * scb->sg_list[1] instead of 0 to the sg pointer in the hscb. - */ - scsi_for_each_sg(cmd, sg, use_sg, i) { - unsigned int len = sg_dma_len(sg); - scb->sg_list[i].address = cpu_to_le32(sg_dma_address(sg)); - scb->sg_list[i].length = cpu_to_le32(len); - scb->sg_length += len; - } - /* Copy the first SG into the data pointer area. */ - hscb->data_pointer = scb->sg_list[0].address; - hscb->data_count = scb->sg_list[0].length; - scb->sg_count = i; - hscb->SG_segment_count = i; - hscb->SG_list_pointer = cpu_to_le32(SCB_DMA_ADDR(scb, &scb->sg_list[1])); - } else { - scb->sg_count = 0; - scb->sg_length = 0; - hscb->SG_segment_count = 0; - hscb->SG_list_pointer = 0; - hscb->data_count = 0; - hscb->data_pointer = 0; - } -} - -/*+F************************************************************************* - * Function: - * aic7xxx_queue - * - * Description: - * Queue a SCB to the controller. - *-F*************************************************************************/ -static int aic7xxx_queue_lck(struct scsi_cmnd *cmd, void (*fn)(struct scsi_cmnd *)) -{ - struct aic7xxx_host *p; - struct aic7xxx_scb *scb; - struct aic_dev_data *aic_dev; - - p = (struct aic7xxx_host *) cmd->device->host->hostdata; - - aic_dev = cmd->device->hostdata; -#ifdef AIC7XXX_VERBOSE_DEBUGGING - if (aic_dev->active_cmds > aic_dev->max_q_depth) - { - printk(WARN_LEAD "Commands queued exceeds queue " - "depth, active=%d\n", - p->host_no, CTL_OF_CMD(cmd), - aic_dev->active_cmds); - } -#endif - - scb = scbq_remove_head(&p->scb_data->free_scbs); - if (scb == NULL) - { - aic7xxx_allocate_scb(p); - scb = scbq_remove_head(&p->scb_data->free_scbs); - if(scb == NULL) - { - printk(WARN_LEAD "Couldn't get a free SCB.\n", p->host_no, - CTL_OF_CMD(cmd)); - return 1; - } - } - scb->cmd = cmd; - - /* - * Make sure the scsi_cmnd pointer is saved, the struct it points to - * is set up properly, and the parity error flag is reset, then send - * the SCB to the sequencer and watch the fun begin. - */ - aic7xxx_position(cmd) = scb->hscb->tag; - cmd->scsi_done = fn; - cmd->result = DID_OK; - aic7xxx_error(cmd) = DID_OK; - aic7xxx_status(cmd) = 0; - cmd->host_scribble = NULL; - - /* - * Construct the SCB beforehand, so the sequencer is - * paused a minimal amount of time. - */ - aic7xxx_buildscb(p, cmd, scb); - - scb->flags |= SCB_ACTIVE | SCB_WAITINGQ; - - scbq_insert_tail(&p->waiting_scbs, scb); - aic7xxx_run_waiting_queues(p); - return (0); -} - -static DEF_SCSI_QCMD(aic7xxx_queue) - -/*+F************************************************************************* - * Function: - * aic7xxx_bus_device_reset - * - * Description: - * Abort or reset the current SCSI command(s). If the scb has not - * previously been aborted, then we attempt to send a BUS_DEVICE_RESET - * message to the target. If the scb has previously been unsuccessfully - * aborted, then we will reset the channel and have all devices renegotiate. - * Returns an enumerated type that indicates the status of the operation. - *-F*************************************************************************/ -static int __aic7xxx_bus_device_reset(struct scsi_cmnd *cmd) -{ - struct aic7xxx_host *p; - struct aic7xxx_scb *scb; - struct aic7xxx_hwscb *hscb; - int channel; - unsigned char saved_scbptr, lastphase; - unsigned char hscb_index; - int disconnected; - struct aic_dev_data *aic_dev; - - if(cmd == NULL) - { - printk(KERN_ERR "aic7xxx_bus_device_reset: called with NULL cmd!\n"); - return FAILED; - } - p = (struct aic7xxx_host *)cmd->device->host->hostdata; - aic_dev = AIC_DEV(cmd); - if(aic7xxx_position(cmd) < p->scb_data->numscbs) - scb = (p->scb_data->scb_array[aic7xxx_position(cmd)]); - else - return FAILED; - - hscb = scb->hscb; - - aic7xxx_isr(p); - aic7xxx_done_cmds_complete(p); - /* If the command was already complete or just completed, then we didn't - * do a reset, return FAILED */ - if(!(scb->flags & SCB_ACTIVE)) - return FAILED; - - pause_sequencer(p); - lastphase = aic_inb(p, LASTPHASE); - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - { - printk(INFO_LEAD "Bus Device reset, scb flags 0x%x, ", - p->host_no, CTL_OF_SCB(scb), scb->flags); - switch (lastphase) - { - case P_DATAOUT: - printk("Data-Out phase\n"); - break; - case P_DATAIN: - printk("Data-In phase\n"); - break; - case P_COMMAND: - printk("Command phase\n"); - break; - case P_MESGOUT: - printk("Message-Out phase\n"); - break; - case P_STATUS: - printk("Status phase\n"); - break; - case P_MESGIN: - printk("Message-In phase\n"); - break; - default: - /* - * We're not in a valid phase, so assume we're idle. - */ - printk("while idle, LASTPHASE = 0x%x\n", lastphase); - break; - } - printk(INFO_LEAD "SCSISIGI 0x%x, SEQADDR 0x%x, SSTAT0 0x%x, SSTAT1 " - "0x%x\n", p->host_no, CTL_OF_SCB(scb), - aic_inb(p, SCSISIGI), - aic_inb(p, SEQADDR0) | (aic_inb(p, SEQADDR1) << 8), - aic_inb(p, SSTAT0), aic_inb(p, SSTAT1)); - printk(INFO_LEAD "SG_CACHEPTR 0x%x, SSTAT2 0x%x, STCNT 0x%x\n", p->host_no, - CTL_OF_SCB(scb), - (p->features & AHC_ULTRA2) ? aic_inb(p, SG_CACHEPTR) : 0, - aic_inb(p, SSTAT2), - aic_inb(p, STCNT + 2) << 16 | aic_inb(p, STCNT + 1) << 8 | - aic_inb(p, STCNT)); - } - - channel = cmd->device->channel; - - /* - * Send a Device Reset Message: - * The target that is holding up the bus may not be the same as - * the one that triggered this timeout (different commands have - * different timeout lengths). Our strategy here is to queue an - * abort message to the timed out target if it is disconnected. - * Otherwise, if we have an active target we stuff the message buffer - * with an abort message and assert ATN in the hopes that the target - * will let go of the bus and go to the mesgout phase. If this - * fails, we'll get another timeout a few seconds later which will - * attempt a bus reset. - */ - saved_scbptr = aic_inb(p, SCBPTR); - disconnected = FALSE; - - if (lastphase != P_BUSFREE) - { - if (aic_inb(p, SCB_TAG) >= p->scb_data->numscbs) - { - printk(WARN_LEAD "Invalid SCB ID %d is active, " - "SCB flags = 0x%x.\n", p->host_no, - CTL_OF_CMD(cmd), scb->hscb->tag, scb->flags); - unpause_sequencer(p, FALSE); - return FAILED; - } - if (scb->hscb->tag == aic_inb(p, SCB_TAG)) - { - if ( (lastphase == P_MESGOUT) || (lastphase == P_MESGIN) ) - { - printk(WARN_LEAD "Device reset, Message buffer " - "in use\n", p->host_no, CTL_OF_SCB(scb)); - unpause_sequencer(p, FALSE); - return FAILED; - } - - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - printk(INFO_LEAD "Device reset message in " - "message buffer\n", p->host_no, CTL_OF_SCB(scb)); - scb->flags |= SCB_RESET | SCB_DEVICE_RESET; - aic7xxx_error(cmd) = DID_RESET; - aic_dev->flags |= BUS_DEVICE_RESET_PENDING; - /* Send the abort message to the active SCB. */ - aic_outb(p, HOST_MSG, MSG_OUT); - aic_outb(p, lastphase | ATNO, SCSISIGO); - unpause_sequencer(p, FALSE); - spin_unlock_irq(p->host->host_lock); - ssleep(1); - spin_lock_irq(p->host->host_lock); - if(aic_dev->flags & BUS_DEVICE_RESET_PENDING) - return FAILED; - else - return SUCCESS; - } - } /* if (last_phase != P_BUSFREE).....indicates we are idle and can work */ - /* - * Simply set the MK_MESSAGE flag and the SEQINT handler will do - * the rest on a reconnect/connect. - */ - scb->hscb->control |= MK_MESSAGE; - scb->flags |= SCB_RESET | SCB_DEVICE_RESET; - aic_dev->flags |= BUS_DEVICE_RESET_PENDING; - /* - * Check to see if the command is on the qinfifo. If it is, then we will - * not need to queue the command again since the card should start it soon - */ - if (aic7xxx_search_qinfifo(p, cmd->device->channel, cmd->device->id, cmd->device->lun, hscb->tag, - 0, TRUE, NULL) == 0) - { - disconnected = TRUE; - if ((hscb_index = aic7xxx_find_scb(p, scb)) != SCB_LIST_NULL) - { - unsigned char scb_control; - - aic_outb(p, hscb_index, SCBPTR); - scb_control = aic_inb(p, SCB_CONTROL); - /* - * If the DISCONNECTED bit is not set in SCB_CONTROL, then we are - * actually on the waiting list, not disconnected, and we don't - * need to requeue the command. - */ - disconnected = (scb_control & DISCONNECTED); - aic_outb(p, scb_control | MK_MESSAGE, SCB_CONTROL); - } - if (disconnected) - { - /* - * Actually requeue this SCB in case we can select the - * device before it reconnects. This can result in the command - * being on the qinfifo twice, but we don't care because it will - * all get cleaned up if/when the reset takes place. - */ - if (aic7xxx_verbose & VERBOSE_RESET_PROCESS) - printk(INFO_LEAD "Queueing device reset command.\n", p->host_no, - CTL_OF_SCB(scb)); - p->qinfifo[p->qinfifonext++] = scb->hscb->tag; - if (p->features & AHC_QUEUE_REGS) - aic_outb(p, p->qinfifonext, HNSCB_QOFF); - else - aic_outb(p, p->qinfifonext, KERNEL_QINPOS); - scb->flags |= SCB_QUEUED_ABORT; - } - } - aic_outb(p, saved_scbptr, SCBPTR); - unpause_sequencer(p, FALSE); - spin_unlock_irq(p->host->host_lock); - msleep(1000/4); - spin_lock_irq(p->host->host_lock); - if(aic_dev->flags & BUS_DEVICE_RESET_PENDING) - return FAILED; - else - return SUCCESS; -} - -static int aic7xxx_bus_device_reset(struct scsi_cmnd *cmd) -{ - int rc; - - spin_lock_irq(cmd->device->host->host_lock); - rc = __aic7xxx_bus_device_reset(cmd); - spin_unlock_irq(cmd->device->host->host_lock); - - return rc; -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_panic_abort - * - * Description: - * Abort the current SCSI command(s). - *-F*************************************************************************/ -static void aic7xxx_panic_abort(struct aic7xxx_host *p, struct scsi_cmnd *cmd) -{ - - printk("aic7xxx driver version %s\n", AIC7XXX_C_VERSION); - printk("Controller type:\n %s\n", board_names[p->board_name_index]); - printk("p->flags=0x%lx, p->chip=0x%x, p->features=0x%x, " - "sequencer %s paused\n", - p->flags, p->chip, p->features, - (aic_inb(p, HCNTRL) & PAUSE) ? "is" : "isn't" ); - pause_sequencer(p); - disable_irq(p->irq); - aic7xxx_print_card(p); - aic7xxx_print_scratch_ram(p); - spin_unlock_irq(p->host->host_lock); - for(;;) barrier(); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_abort - * - * Description: - * Abort the current SCSI command(s). - *-F*************************************************************************/ -static int __aic7xxx_abort(struct scsi_cmnd *cmd) -{ - struct aic7xxx_scb *scb = NULL; - struct aic7xxx_host *p; - int found=0, disconnected; - unsigned char saved_hscbptr, hscbptr, scb_control; - struct aic_dev_data *aic_dev; - - if(cmd == NULL) - { - printk(KERN_ERR "aic7xxx_abort: called with NULL cmd!\n"); - return FAILED; - } - p = (struct aic7xxx_host *)cmd->device->host->hostdata; - aic_dev = AIC_DEV(cmd); - if(aic7xxx_position(cmd) < p->scb_data->numscbs) - scb = (p->scb_data->scb_array[aic7xxx_position(cmd)]); - else - return FAILED; - - aic7xxx_isr(p); - aic7xxx_done_cmds_complete(p); - /* If the command was already complete or just completed, then we didn't - * do a reset, return FAILED */ - if(!(scb->flags & SCB_ACTIVE)) - return FAILED; - - pause_sequencer(p); - - /* - * I added a new config option to the driver: "panic_on_abort" that will - * cause the driver to panic and the machine to stop on the first abort - * or reset call into the driver. At that point, it prints out a lot of - * useful information for me which I can then use to try and debug the - * problem. Simply enable the boot time prompt in order to activate this - * code. - */ - if (aic7xxx_panic_on_abort) - aic7xxx_panic_abort(p, cmd); - - if (aic7xxx_verbose & VERBOSE_ABORT) - { - printk(INFO_LEAD "Aborting scb %d, flags 0x%x, SEQADDR 0x%x, LASTPHASE " - "0x%x\n", - p->host_no, CTL_OF_SCB(scb), scb->hscb->tag, scb->flags, - aic_inb(p, SEQADDR0) | (aic_inb(p, SEQADDR1) << 8), - aic_inb(p, LASTPHASE)); - printk(INFO_LEAD "SG_CACHEPTR 0x%x, SG_COUNT %d, SCSISIGI 0x%x\n", - p->host_no, CTL_OF_SCB(scb), (p->features & AHC_ULTRA2) ? - aic_inb(p, SG_CACHEPTR) : 0, aic_inb(p, SG_COUNT), - aic_inb(p, SCSISIGI)); - printk(INFO_LEAD "SSTAT0 0x%x, SSTAT1 0x%x, SSTAT2 0x%x\n", - p->host_no, CTL_OF_SCB(scb), aic_inb(p, SSTAT0), - aic_inb(p, SSTAT1), aic_inb(p, SSTAT2)); - } - - if (scb->flags & SCB_WAITINGQ) - { - if (aic7xxx_verbose & VERBOSE_ABORT_PROCESS) - printk(INFO_LEAD "SCB found on waiting list and " - "aborted.\n", p->host_no, CTL_OF_SCB(scb)); - scbq_remove(&p->waiting_scbs, scb); - scbq_remove(&aic_dev->delayed_scbs, scb); - aic_dev->active_cmds++; - p->activescbs++; - scb->flags &= ~(SCB_WAITINGQ | SCB_ACTIVE); - scb->flags |= SCB_ABORT | SCB_QUEUED_FOR_DONE; - goto success; - } - -/* - * We just checked the waiting_q, now for the QINFIFO - */ - if ( ((found = aic7xxx_search_qinfifo(p, cmd->device->id, cmd->device->channel, - cmd->device->lun, scb->hscb->tag, SCB_ABORT | SCB_QUEUED_FOR_DONE, - FALSE, NULL)) != 0) && - (aic7xxx_verbose & VERBOSE_ABORT_PROCESS)) - { - printk(INFO_LEAD "SCB found in QINFIFO and aborted.\n", p->host_no, - CTL_OF_SCB(scb)); - goto success; - } - -/* - * QINFIFO, waitingq, completeq done. Next, check WAITING_SCB list in card - */ - - saved_hscbptr = aic_inb(p, SCBPTR); - if ((hscbptr = aic7xxx_find_scb(p, scb)) != SCB_LIST_NULL) - { - aic_outb(p, hscbptr, SCBPTR); - scb_control = aic_inb(p, SCB_CONTROL); - disconnected = scb_control & DISCONNECTED; - /* - * If the DISCONNECTED bit is not set in SCB_CONTROL, then we are - * either currently active or on the waiting list. - */ - if(!disconnected && aic_inb(p, LASTPHASE) == P_BUSFREE) { - if (aic7xxx_verbose & VERBOSE_ABORT_PROCESS) - printk(INFO_LEAD "SCB found on hardware waiting" - " list and aborted.\n", p->host_no, CTL_OF_SCB(scb)); - /* If we are the only waiting command, stop the selection engine */ - if (aic_inb(p, WAITING_SCBH) == hscbptr && aic_inb(p, SCB_NEXT) == - SCB_LIST_NULL) - { - aic_outb(p, aic_inb(p, SCSISEQ) & ~ENSELO, SCSISEQ); - aic_outb(p, CLRSELTIMEO, CLRSINT1); - aic_outb(p, SCB_LIST_NULL, WAITING_SCBH); - } - else - { - unsigned char prev, next; - prev = SCB_LIST_NULL; - next = aic_inb(p, WAITING_SCBH); - while(next != SCB_LIST_NULL) - { - aic_outb(p, next, SCBPTR); - if (next == hscbptr) - { - next = aic_inb(p, SCB_NEXT); - if (prev != SCB_LIST_NULL) - { - aic_outb(p, prev, SCBPTR); - aic_outb(p, next, SCB_NEXT); - } - else - aic_outb(p, next, WAITING_SCBH); - aic_outb(p, hscbptr, SCBPTR); - next = SCB_LIST_NULL; - } - else - { - prev = next; - next = aic_inb(p, SCB_NEXT); - } - } - } - aic_outb(p, SCB_LIST_NULL, SCB_TAG); - aic_outb(p, 0, SCB_CONTROL); - aic7xxx_add_curscb_to_free_list(p); - scb->flags = SCB_ABORT | SCB_QUEUED_FOR_DONE; - goto success; - } - else if (!disconnected) - { - /* - * We are the currently active command - */ - if((aic_inb(p, LASTPHASE) == P_MESGIN) || - (aic_inb(p, LASTPHASE) == P_MESGOUT)) - { - /* - * Message buffer busy, unable to abort - */ - printk(INFO_LEAD "message buffer busy, unable to abort.\n", - p->host_no, CTL_OF_SCB(scb)); - unpause_sequencer(p, FALSE); - return FAILED; - } - /* Fallthrough to below, set ATNO after we set SCB_CONTROL */ - } - aic_outb(p, scb_control | MK_MESSAGE, SCB_CONTROL); - if(!disconnected) - { - aic_outb(p, HOST_MSG, MSG_OUT); - aic_outb(p, aic_inb(p, SCSISIGI) | ATNO, SCSISIGO); - } - aic_outb(p, saved_hscbptr, SCBPTR); - } - else - { - /* - * The scb isn't in the card at all and it is active and it isn't in - * any of the queues, so it must be disconnected and paged out. Fall - * through to the code below. - */ - disconnected = 1; - } - - p->flags |= AHC_ABORT_PENDING; - scb->flags |= SCB_QUEUED_ABORT | SCB_ABORT | SCB_RECOVERY_SCB; - scb->hscb->control |= MK_MESSAGE; - if(disconnected) - { - if (aic7xxx_verbose & VERBOSE_ABORT_PROCESS) - printk(INFO_LEAD "SCB disconnected. Queueing Abort" - " SCB.\n", p->host_no, CTL_OF_SCB(scb)); - p->qinfifo[p->qinfifonext++] = scb->hscb->tag; - if (p->features & AHC_QUEUE_REGS) - aic_outb(p, p->qinfifonext, HNSCB_QOFF); - else - aic_outb(p, p->qinfifonext, KERNEL_QINPOS); - } - unpause_sequencer(p, FALSE); - spin_unlock_irq(p->host->host_lock); - msleep(1000/4); - spin_lock_irq(p->host->host_lock); - if (p->flags & AHC_ABORT_PENDING) - { - if (aic7xxx_verbose & VERBOSE_ABORT_RETURN) - printk(INFO_LEAD "Abort never delivered, returning FAILED\n", p->host_no, - CTL_OF_CMD(cmd)); - p->flags &= ~AHC_ABORT_PENDING; - return FAILED; - } - if (aic7xxx_verbose & VERBOSE_ABORT_RETURN) - printk(INFO_LEAD "Abort successful.\n", p->host_no, CTL_OF_CMD(cmd)); - return SUCCESS; - -success: - if (aic7xxx_verbose & VERBOSE_ABORT_RETURN) - printk(INFO_LEAD "Abort successful.\n", p->host_no, CTL_OF_CMD(cmd)); - aic7xxx_run_done_queue(p, TRUE); - unpause_sequencer(p, FALSE); - return SUCCESS; -} - -static int aic7xxx_abort(struct scsi_cmnd *cmd) -{ - int rc; - - spin_lock_irq(cmd->device->host->host_lock); - rc = __aic7xxx_abort(cmd); - spin_unlock_irq(cmd->device->host->host_lock); - - return rc; -} - - -/*+F************************************************************************* - * Function: - * aic7xxx_reset - * - * Description: - * Resetting the bus always succeeds - is has to, otherwise the - * kernel will panic! Try a surgical technique - sending a BUS - * DEVICE RESET message - on the offending target before pulling - * the SCSI bus reset line. - *-F*************************************************************************/ -static int aic7xxx_reset(struct scsi_cmnd *cmd) -{ - struct aic7xxx_scb *scb; - struct aic7xxx_host *p; - struct aic_dev_data *aic_dev; - - p = (struct aic7xxx_host *) cmd->device->host->hostdata; - spin_lock_irq(p->host->host_lock); - - aic_dev = AIC_DEV(cmd); - if(aic7xxx_position(cmd) < p->scb_data->numscbs) - { - scb = (p->scb_data->scb_array[aic7xxx_position(cmd)]); - if (scb->cmd != cmd) - scb = NULL; - } - else - { - scb = NULL; - } - - /* - * I added a new config option to the driver: "panic_on_abort" that will - * cause the driver to panic and the machine to stop on the first abort - * or reset call into the driver. At that point, it prints out a lot of - * useful information for me which I can then use to try and debug the - * problem. Simply enable the boot time prompt in order to activate this - * code. - */ - if (aic7xxx_panic_on_abort) - aic7xxx_panic_abort(p, cmd); - - pause_sequencer(p); - - while((aic_inb(p, INTSTAT) & INT_PEND) && !(p->flags & AHC_IN_ISR)) - { - aic7xxx_isr(p); - pause_sequencer(p); - } - aic7xxx_done_cmds_complete(p); - - if(scb && (scb->cmd == NULL)) - { - /* - * We just completed the command when we ran the isr stuff, so we no - * longer have it. - */ - unpause_sequencer(p, FALSE); - spin_unlock_irq(p->host->host_lock); - return SUCCESS; - } - -/* - * By this point, we want to already know what we are going to do and - * only have the following code implement our course of action. - */ - aic7xxx_reset_channel(p, cmd->device->channel, TRUE); - if (p->features & AHC_TWIN) - { - aic7xxx_reset_channel(p, cmd->device->channel ^ 0x01, TRUE); - restart_sequencer(p); - } - aic_outb(p, aic_inb(p, SIMODE1) & ~(ENREQINIT|ENBUSFREE), SIMODE1); - aic7xxx_clear_intstat(p); - p->flags &= ~AHC_HANDLING_REQINITS; - p->msg_type = MSG_TYPE_NONE; - p->msg_index = 0; - p->msg_len = 0; - aic7xxx_run_done_queue(p, TRUE); - unpause_sequencer(p, FALSE); - spin_unlock_irq(p->host->host_lock); - ssleep(2); - return SUCCESS; -} - -/*+F************************************************************************* - * Function: - * aic7xxx_biosparam - * - * Description: - * Return the disk geometry for the given SCSI device. - * - * Note: - * This function is broken for today's really large drives and needs - * fixed. - *-F*************************************************************************/ -static int -aic7xxx_biosparam(struct scsi_device *sdev, struct block_device *bdev, - sector_t capacity, int geom[]) -{ - sector_t heads, sectors, cylinders; - int ret; - struct aic7xxx_host *p; - unsigned char *buf; - - p = (struct aic7xxx_host *) sdev->host->hostdata; - buf = scsi_bios_ptable(bdev); - - if ( buf ) - { - ret = scsi_partsize(buf, capacity, &geom[2], &geom[0], &geom[1]); - kfree(buf); - if ( ret != -1 ) - return(ret); - } - - heads = 64; - sectors = 32; - cylinders = capacity >> 11; - - if ((p->flags & AHC_EXTEND_TRANS_A) && (cylinders > 1024)) - { - heads = 255; - sectors = 63; - cylinders = capacity >> 14; - if(capacity > (65535 * heads * sectors)) - cylinders = 65535; - else - cylinders = ((unsigned int)capacity) / (unsigned int)(heads * sectors); - } - - geom[0] = (int)heads; - geom[1] = (int)sectors; - geom[2] = (int)cylinders; - - return (0); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_release - * - * Description: - * Free the passed in Scsi_Host memory structures prior to unloading the - * module. - *-F*************************************************************************/ -static int -aic7xxx_release(struct Scsi_Host *host) -{ - struct aic7xxx_host *p = (struct aic7xxx_host *) host->hostdata; - struct aic7xxx_host *next, *prev; - - if(p->irq) - free_irq(p->irq, p); -#ifdef MMAPIO - if(p->maddr) - { - iounmap(p->maddr); - } -#endif /* MMAPIO */ - if(!p->pdev) - release_region(p->base, MAXREG - MINREG); -#ifdef CONFIG_PCI - else { - pci_release_regions(p->pdev); - pci_dev_put(p->pdev); - } -#endif - prev = NULL; - next = first_aic7xxx; - while(next != NULL) - { - if(next == p) - { - if(prev == NULL) - first_aic7xxx = next->next; - else - prev->next = next->next; - } - else - { - prev = next; - } - next = next->next; - } - aic7xxx_free(p); - return(0); -} - -/*+F************************************************************************* - * Function: - * aic7xxx_print_card - * - * Description: - * Print out all of the control registers on the card - * - * NOTE: This function is not yet safe for use on the VLB and EISA - * controllers, so it isn't used on those controllers at all. - *-F*************************************************************************/ -static void -aic7xxx_print_card(struct aic7xxx_host *p) -{ - int i, j, k, chip; - static struct register_ranges { - int num_ranges; - int range_val[32]; - } cards_ds[] = { - { 0, {0,} }, /* none */ - {10, {0x00, 0x05, 0x08, 0x11, 0x18, 0x19, 0x1f, 0x1f, 0x60, 0x60, /*7771*/ - 0x62, 0x66, 0x80, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9b, 0x9f} }, - { 9, {0x00, 0x05, 0x08, 0x11, 0x18, 0x1f, 0x60, 0x60, 0x62, 0x66, /*7850*/ - 0x80, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9f} }, - { 9, {0x00, 0x05, 0x08, 0x11, 0x18, 0x1f, 0x60, 0x60, 0x62, 0x66, /*7860*/ - 0x80, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9f} }, - {10, {0x00, 0x05, 0x08, 0x11, 0x18, 0x19, 0x1c, 0x1f, 0x60, 0x60, /*7870*/ - 0x62, 0x66, 0x80, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9f} }, - {10, {0x00, 0x05, 0x08, 0x11, 0x18, 0x1a, 0x1c, 0x1f, 0x60, 0x60, /*7880*/ - 0x62, 0x66, 0x80, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9f} }, - {16, {0x00, 0x05, 0x08, 0x11, 0x18, 0x1f, 0x60, 0x60, 0x62, 0x66, /*7890*/ - 0x84, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9a, 0x9f, 0x9f, - 0xe0, 0xf1, 0xf4, 0xf4, 0xf6, 0xf6, 0xf8, 0xf8, 0xfa, 0xfc, - 0xfe, 0xff} }, - {12, {0x00, 0x05, 0x08, 0x11, 0x18, 0x19, 0x1b, 0x1f, 0x60, 0x60, /*7895*/ - 0x62, 0x66, 0x80, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9a, - 0x9f, 0x9f, 0xe0, 0xf1} }, - {16, {0x00, 0x05, 0x08, 0x11, 0x18, 0x1f, 0x60, 0x60, 0x62, 0x66, /*7896*/ - 0x84, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9a, 0x9f, 0x9f, - 0xe0, 0xf1, 0xf4, 0xf4, 0xf6, 0xf6, 0xf8, 0xf8, 0xfa, 0xfc, - 0xfe, 0xff} }, - {12, {0x00, 0x05, 0x08, 0x11, 0x18, 0x1f, 0x60, 0x60, 0x62, 0x66, /*7892*/ - 0x84, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9a, 0x9c, 0x9f, - 0xe0, 0xf1, 0xf4, 0xfc} }, - {12, {0x00, 0x05, 0x08, 0x11, 0x18, 0x1f, 0x60, 0x60, 0x62, 0x66, /*7899*/ - 0x84, 0x8e, 0x90, 0x95, 0x97, 0x97, 0x9a, 0x9a, 0x9c, 0x9f, - 0xe0, 0xf1, 0xf4, 0xfc} }, - }; - chip = p->chip & AHC_CHIPID_MASK; - printk("%s at ", - board_names[p->board_name_index]); - switch(p->chip & ~AHC_CHIPID_MASK) - { - case AHC_VL: - printk("VLB Slot %d.\n", p->pci_device_fn); - break; - case AHC_EISA: - printk("EISA Slot %d.\n", p->pci_device_fn); - break; - case AHC_PCI: - default: - printk("PCI %d/%d/%d.\n", p->pci_bus, PCI_SLOT(p->pci_device_fn), - PCI_FUNC(p->pci_device_fn)); - break; - } - - /* - * the registers on the card.... - */ - printk("Card Dump:\n"); - k = 0; - for(i=0; i<cards_ds[chip].num_ranges; i++) - { - for(j = cards_ds[chip].range_val[ i * 2 ]; - j <= cards_ds[chip].range_val[ i * 2 + 1 ] ; - j++) - { - printk("%02x:%02x ", j, aic_inb(p, j)); - if(++k == 13) - { - printk("\n"); - k=0; - } - } - } - if(k != 0) - printk("\n"); - - /* - * If this was an Ultra2 controller, then we just hosed the card in terms - * of the QUEUE REGS. This function is only called at init time or by - * the panic_abort function, so it's safe to assume a generic init time - * setting here - */ - - if(p->features & AHC_QUEUE_REGS) - { - aic_outb(p, 0, SDSCB_QOFF); - aic_outb(p, 0, SNSCB_QOFF); - aic_outb(p, 0, HNSCB_QOFF); - } - -} - -/*+F************************************************************************* - * Function: - * aic7xxx_print_scratch_ram - * - * Description: - * Print out the scratch RAM values on the card. - *-F*************************************************************************/ -static void -aic7xxx_print_scratch_ram(struct aic7xxx_host *p) -{ - int i, k; - - k = 0; - printk("Scratch RAM:\n"); - for(i = SRAM_BASE; i < SEQCTL; i++) - { - printk("%02x:%02x ", i, aic_inb(p, i)); - if(++k == 13) - { - printk("\n"); - k=0; - } - } - if (p->features & AHC_MORE_SRAM) - { - for(i = TARG_OFFSET; i < 0x80; i++) - { - printk("%02x:%02x ", i, aic_inb(p, i)); - if(++k == 13) - { - printk("\n"); - k=0; - } - } - } - printk("\n"); -} - - -#include "aic7xxx_old/aic7xxx_proc.c" - -MODULE_LICENSE("Dual BSD/GPL"); -MODULE_VERSION(AIC7XXX_H_VERSION); - - -static struct scsi_host_template driver_template = { - .show_info = aic7xxx_show_info, - .detect = aic7xxx_detect, - .release = aic7xxx_release, - .info = aic7xxx_info, - .queuecommand = aic7xxx_queue, - .slave_alloc = aic7xxx_slave_alloc, - .slave_configure = aic7xxx_slave_configure, - .slave_destroy = aic7xxx_slave_destroy, - .bios_param = aic7xxx_biosparam, - .eh_abort_handler = aic7xxx_abort, - .eh_device_reset_handler = aic7xxx_bus_device_reset, - .eh_host_reset_handler = aic7xxx_reset, - .can_queue = 255, - .this_id = -1, - .max_sectors = 2048, - .cmd_per_lun = 3, - .use_clustering = ENABLE_CLUSTERING, -}; - -#include "scsi_module.c" - -/* - * Overrides for Emacs so that we almost follow Linus's tabbing style. - * Emacs will notice this stuff at the end of the file and automatically - * adjust the settings for this buffer only. This must remain at the end - * of the file. - * --------------------------------------------------------------------------- - * Local variables: - * c-indent-level: 2 - * c-brace-imaginary-offset: 0 - * c-brace-offset: -2 - * c-argdecl-indent: 2 - * c-label-offset: -2 - * c-continued-statement-offset: 2 - * c-continued-brace-offset: 0 - * indent-tabs-mode: nil - * tab-width: 8 - * End: - */ diff --git a/drivers/scsi/aic7xxx_old/aic7xxx.h b/drivers/scsi/aic7xxx_old/aic7xxx.h deleted file mode 100644 index 0116c8128a6..00000000000 --- a/drivers/scsi/aic7xxx_old/aic7xxx.h +++ /dev/null @@ -1,28 +0,0 @@ -/*+M************************************************************************* - * Adaptec AIC7xxx device driver for Linux. - * - * Copyright (c) 1994 John Aycock - * The University of Calgary Department of Computer Science. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2, or (at your option) - * any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; see the file COPYING. If not, write to - * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. - * - * $Id: aic7xxx.h,v 3.2 1996/07/23 03:37:26 deang Exp $ - *-M*************************************************************************/ -#ifndef _aic7xxx_h -#define _aic7xxx_h - -#define AIC7XXX_H_VERSION "5.2.0" - -#endif /* _aic7xxx_h */ diff --git a/drivers/scsi/aic7xxx_old/aic7xxx.reg b/drivers/scsi/aic7xxx_old/aic7xxx.reg deleted file mode 100644 index f67b4bced01..00000000000 --- a/drivers/scsi/aic7xxx_old/aic7xxx.reg +++ /dev/null @@ -1,1401 +0,0 @@ -/* - * Aic7xxx register and scratch ram definitions. - * - * Copyright (c) 1994-1998 Justin Gibbs. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions, and the following disclaimer, - * without modification, immediately at the beginning of the file. - * 2. The name of the author may not be used to endorse or promote products - * derived from this software without specific prior written permission. - * - * Where this Software is combined with software released under the terms of - * the GNU General Public License ("GPL") and the terms of the GPL would require the - * combined work to also be released under the terms of the GPL, the terms - * and conditions of this License will apply in addition to those of the - * GPL with the exception of any terms or conditions of this License that - * conflict with, or are expressly prohibited by, the GPL. - * - * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND - * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR - * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS - * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) - * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT - * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY - * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF - * SUCH DAMAGE. - * - * $Id: aic7xxx.reg,v 1.4 1997/06/27 19:38:39 gibbs Exp $ - */ - -/* - * This file is processed by the aic7xxx_asm utility for use in assembling - * firmware for the aic7xxx family of SCSI host adapters as well as to generate - * a C header file for use in the kernel portion of the Aic7xxx driver. - * - * All page numbers refer to the Adaptec AIC-7770 Data Book available from - * Adaptec's Technical Documents Department 1-800-934-2766 - */ - -/* - * SCSI Sequence Control (p. 3-11). - * Each bit, when set starts a specific SCSI sequence on the bus - */ -register SCSISEQ { - address 0x000 - access_mode RW - bit TEMODE 0x80 - bit ENSELO 0x40 - bit ENSELI 0x20 - bit ENRSELI 0x10 - bit ENAUTOATNO 0x08 - bit ENAUTOATNI 0x04 - bit ENAUTOATNP 0x02 - bit SCSIRSTO 0x01 -} - -/* - * SCSI Transfer Control 0 Register (pp. 3-13). - * Controls the SCSI module data path. - */ -register SXFRCTL0 { - address 0x001 - access_mode RW - bit DFON 0x80 - bit DFPEXP 0x40 - bit FAST20 0x20 - bit CLRSTCNT 0x10 - bit SPIOEN 0x08 - bit SCAMEN 0x04 - bit CLRCHN 0x02 -} - -/* - * SCSI Transfer Control 1 Register (pp. 3-14,15). - * Controls the SCSI module data path. - */ -register SXFRCTL1 { - address 0x002 - access_mode RW - bit BITBUCKET 0x80 - bit SWRAPEN 0x40 - bit ENSPCHK 0x20 - mask STIMESEL 0x18 - bit ENSTIMER 0x04 - bit ACTNEGEN 0x02 - bit STPWEN 0x01 /* Powered Termination */ -} - -/* - * SCSI Control Signal Read Register (p. 3-15). - * Reads the actual state of the SCSI bus pins - */ -register SCSISIGI { - address 0x003 - access_mode RO - bit CDI 0x80 - bit IOI 0x40 - bit MSGI 0x20 - bit ATNI 0x10 - bit SELI 0x08 - bit BSYI 0x04 - bit REQI 0x02 - bit ACKI 0x01 -/* - * Possible phases in SCSISIGI - */ - mask PHASE_MASK CDI|IOI|MSGI - mask P_DATAOUT 0x00 - mask P_DATAIN IOI - mask P_COMMAND CDI - mask P_MESGOUT CDI|MSGI - mask P_STATUS CDI|IOI - mask P_MESGIN CDI|IOI|MSGI -} - -/* - * SCSI Control Signal Write Register (p. 3-16). - * Writing to this register modifies the control signals on the bus. Only - * those signals that are allowed in the current mode (Initiator/Target) are - * asserted. - */ -register SCSISIGO { - address 0x003 - access_mode WO - bit CDO 0x80 - bit IOO 0x40 - bit MSGO 0x20 - bit ATNO 0x10 - bit SELO 0x08 - bit BSYO 0x04 - bit REQO 0x02 - bit ACKO 0x01 -/* - * Possible phases to write into SCSISIG0 - */ - mask PHASE_MASK CDI|IOI|MSGI - mask P_DATAOUT 0x00 - mask P_DATAIN IOI - mask P_COMMAND CDI - mask P_MESGOUT CDI|MSGI - mask P_STATUS CDI|IOI - mask P_MESGIN CDI|IOI|MSGI -} - -/* - * SCSI Rate Control (p. 3-17). - * Contents of this register determine the Synchronous SCSI data transfer - * rate and the maximum synchronous Req/Ack offset. An offset of 0 in the - * SOFS (3:0) bits disables synchronous data transfers. Any offset value - * greater than 0 enables synchronous transfers. - */ -register SCSIRATE { - address 0x004 - access_mode RW - bit WIDEXFER 0x80 /* Wide transfer control */ - mask SXFR 0x70 /* Sync transfer rate */ - mask SXFR_ULTRA2 0x7f /* Sync transfer rate */ - mask SOFS 0x0f /* Sync offset */ -} - -/* - * SCSI ID (p. 3-18). - * Contains the ID of the board and the current target on the - * selected channel. - */ -register SCSIID { - address 0x005 - access_mode RW - mask TID 0xf0 /* Target ID mask */ - mask OID 0x0f /* Our ID mask */ - /* - * SCSI Maximum Offset (p. 4-61 aic7890/91 Data Book) - * The aic7890/91 allow an offset of up to 127 transfers in both wide - * and narrow mode. - */ - alias SCSIOFFSET - mask SOFS_ULTRA2 0x7f /* Sync offset U2 chips */ -} - -/* - * SCSI Latched Data (p. 3-19). - * Read/Write latches used to transfer data on the SCSI bus during - * Automatic or Manual PIO mode. SCSIDATH can be used for the - * upper byte of a 16bit wide asynchronouse data phase transfer. - */ -register SCSIDATL { - address 0x006 - access_mode RW -} - -register SCSIDATH { - address 0x007 - access_mode RW -} - -/* - * SCSI Transfer Count (pp. 3-19,20) - * These registers count down the number of bytes transferred - * across the SCSI bus. The counter is decremented only once - * the data has been safely transferred. SDONE in SSTAT0 is - * set when STCNT goes to 0 - */ -register STCNT { - address 0x008 - size 3 - access_mode RW -} - -/* - * Option Mode Register (Alternate Mode) (p. 5-198) - * This register is used to set certain options on Ultra3 based chips. - * The chip must be in alternate mode (bit ALT_MODE in SFUNCT must be set) - */ -register OPTIONMODE { - address 0x008 - access_mode RW - bit AUTORATEEN 0x80 - bit AUTOACKEN 0x40 - bit ATNMGMNTEN 0x20 - bit BUSFREEREV 0x10 - bit EXPPHASEDIS 0x08 - bit SCSIDATL_IMGEN 0x04 - bit AUTO_MSGOUT_DE 0x02 - bit DIS_MSGIN_DUALEDGE 0x01 -} - - -/* - * Clear SCSI Interrupt 0 (p. 3-20) - * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT0. - */ -register CLRSINT0 { - address 0x00b - access_mode WO - bit CLRSELDO 0x40 - bit CLRSELDI 0x20 - bit CLRSELINGO 0x10 - bit CLRSWRAP 0x08 - bit CLRSPIORDY 0x02 -} - -/* - * SCSI Status 0 (p. 3-21) - * Contains one set of SCSI Interrupt codes - * These are most likely of interest to the sequencer - */ -register SSTAT0 { - address 0x00b - access_mode RO - bit TARGET 0x80 /* Board acting as target */ - bit SELDO 0x40 /* Selection Done */ - bit SELDI 0x20 /* Board has been selected */ - bit SELINGO 0x10 /* Selection In Progress */ - bit SWRAP 0x08 /* 24bit counter wrap */ - bit IOERR 0x08 /* LVD Tranceiver mode changed */ - bit SDONE 0x04 /* STCNT = 0x000000 */ - bit SPIORDY 0x02 /* SCSI PIO Ready */ - bit DMADONE 0x01 /* DMA transfer completed */ -} - -/* - * Clear SCSI Interrupt 1 (p. 3-23) - * Writing a 1 to a bit clears the associated SCSI Interrupt in SSTAT1. - */ -register CLRSINT1 { - address 0x00c - access_mode WO - bit CLRSELTIMEO 0x80 - bit CLRATNO 0x40 - bit CLRSCSIRSTI 0x20 - bit CLRBUSFREE 0x08 - bit CLRSCSIPERR 0x04 - bit CLRPHASECHG 0x02 - bit CLRREQINIT 0x01 -} - -/* - * SCSI Status 1 (p. 3-24) - */ -register SSTAT1 { - address 0x00c - access_mode RO - bit SELTO 0x80 - bit ATNTARG 0x40 - bit SCSIRSTI 0x20 - bit PHASEMIS 0x10 - bit BUSFREE 0x08 - bit SCSIPERR 0x04 - bit PHASECHG 0x02 - bit REQINIT 0x01 -} - -/* - * SCSI Status 2 (pp. 3-25,26) - */ -register SSTAT2 { - address 0x00d - access_mode RO - bit OVERRUN 0x80 - bit SHVALID 0x40 - bit WIDE_RES 0x20 - bit EXP_ACTIVE 0x10 /* SCSI Expander Active */ - bit CRCVALERR 0x08 /* CRC Value Error */ - bit CRCENDERR 0x04 /* CRC End Error */ - bit CRCREQERR 0x02 /* CRC REQ Error */ - bit DUAL_EDGE_ERROR 0x01 /* Invalid pins for Dual Edge phase */ - mask SFCNT 0x1f -} - -/* - * SCSI Status 3 (p. 3-26) - */ -register SSTAT3 { - address 0x00e - access_mode RO - mask SCSICNT 0xf0 - mask OFFCNT 0x0f -} - -/* - * SCSI ID for the aic7890/91 chips - */ -register SCSIID_ULTRA2 { - address 0x00f - access_mode RW - mask TID 0xf0 /* Target ID mask */ - mask OID 0x0f /* Our ID mask */ -} - -/* - * SCSI Interrupt Mode 1 (p. 3-28) - * Setting any bit will enable the corresponding function - * in SIMODE0 to interrupt via the IRQ pin. - */ -register SIMODE0 { - address 0x010 - access_mode RW - bit ENSELDO 0x40 - bit ENSELDI 0x20 - bit ENSELINGO 0x10 - bit ENSWRAP 0x08 - bit ENIOERR 0x08 /* LVD Tranceiver mode changes */ - bit ENSDONE 0x04 - bit ENSPIORDY 0x02 - bit ENDMADONE 0x01 -} - -/* - * SCSI Interrupt Mode 1 (pp. 3-28,29) - * Setting any bit will enable the corresponding function - * in SIMODE1 to interrupt via the IRQ pin. - */ -register SIMODE1 { - address 0x011 - access_mode RW - bit ENSELTIMO 0x80 - bit ENATNTARG 0x40 - bit ENSCSIRST 0x20 - bit ENPHASEMIS 0x10 - bit ENBUSFREE 0x08 - bit ENSCSIPERR 0x04 - bit ENPHASECHG 0x02 - bit ENREQINIT 0x01 -} - -/* - * SCSI Data Bus (High) (p. 3-29) - * This register reads data on the SCSI Data bus directly. - */ -register SCSIBUSL { - address 0x012 - access_mode RO -} - -register SCSIBUSH { - address 0x013 - access_mode RO -} - -/* - * SCSI/Host Address (p. 3-30) - * These registers hold the host address for the byte about to be - * transferred on the SCSI bus. They are counted up in the same - * manner as STCNT is counted down. SHADDR should always be used - * to determine the address of the last byte transferred since HADDR - * can be skewed by write ahead. - */ -register SHADDR { - address 0x014 - size 4 - access_mode RO -} - -/* - * Selection Timeout Timer (p. 3-30) - */ -register SELTIMER { - address 0x018 - access_mode RW - bit STAGE6 0x20 - bit STAGE5 0x10 - bit STAGE4 0x08 - bit STAGE3 0x04 - bit STAGE2 0x02 - bit STAGE1 0x01 -} - -/* - * Selection/Reselection ID (p. 3-31) - * Upper four bits are the device id. The ONEBIT is set when the re/selecting - * device did not set its own ID. - */ -register SELID { - address 0x019 - access_mode RW - mask SELID_MASK 0xf0 - bit ONEBIT 0x08 -} - -/* - * Serial Port I/O Cabability register (p. 4-95 aic7860 Data Book) - * Indicates if external logic has been attached to the chip to - * perform the tasks of accessing a serial eeprom, testing termination - * strength, and performing cable detection. On the aic7860, most of - * these features are handled on chip, but on the aic7855 an attached - * aic3800 does the grunt work. - */ -register SPIOCAP { - address 0x01b - access_mode RW - bit SOFT1 0x80 - bit SOFT0 0x40 - bit SOFTCMDEN 0x20 - bit HAS_BRDCTL 0x10 /* External Board control */ - bit SEEPROM 0x08 /* External serial eeprom logic */ - bit EEPROM 0x04 /* Writable external BIOS ROM */ - bit ROM 0x02 /* Logic for accessing external ROM */ - bit SSPIOCPS 0x01 /* Termination and cable detection */ -} - -/* - * SCSI Block Control (p. 3-32) - * Controls Bus type and channel selection. In a twin channel configuration - * addresses 0x00-0x1e are gated to the appropriate channel based on this - * register. SELWIDE allows for the coexistence of 8bit and 16bit devices - * on a wide bus. - */ -register SBLKCTL { - address 0x01f - access_mode RW - bit DIAGLEDEN 0x80 /* Aic78X0 only */ - bit DIAGLEDON 0x40 /* Aic78X0 only */ - bit AUTOFLUSHDIS 0x20 - bit SELBUSB 0x08 - bit ENAB40 0x08 /* LVD transceiver active */ - bit ENAB20 0x04 /* SE/HVD transceiver active */ - bit SELWIDE 0x02 - bit XCVR 0x01 /* External transceiver active */ -} - -/* - * Sequencer Control (p. 3-33) - * Error detection mode and speed configuration - */ -register SEQCTL { - address 0x060 - access_mode RW - bit PERRORDIS 0x80 - bit PAUSEDIS 0x40 - bit FAILDIS 0x20 - bit FASTMODE 0x10 - bit BRKADRINTEN 0x08 - bit STEP 0x04 - bit SEQRESET 0x02 - bit LOADRAM 0x01 -} - -/* - * Sequencer RAM Data (p. 3-34) - * Single byte window into the Scratch Ram area starting at the address - * specified by SEQADDR0 and SEQADDR1. To write a full word, simply write - * four bytes in succession. The SEQADDRs will increment after the most - * significant byte is written - */ -register SEQRAM { - address 0x061 - access_mode RW -} - -/* - * Sequencer Address Registers (p. 3-35) - * Only the first bit of SEQADDR1 holds addressing information - */ -register SEQADDR0 { - address 0x062 - access_mode RW -} - -register SEQADDR1 { - address 0x063 - access_mode RW - mask SEQADDR1_MASK 0x01 -} - -/* - * Accumulator - * We cheat by passing arguments in the Accumulator up to the kernel driver - */ -register ACCUM { - address 0x064 - access_mode RW - accumulator -} - -register SINDEX { - address 0x065 - access_mode RW - sindex -} - -register DINDEX { - address 0x066 - access_mode RW -} - -register ALLONES { - address 0x069 - access_mode RO - allones -} - -register ALLZEROS { - address 0x06a - access_mode RO - allzeros -} - -register NONE { - address 0x06a - access_mode WO - none -} - -register FLAGS { - address 0x06b - access_mode RO - bit ZERO 0x02 - bit CARRY 0x01 -} - -register SINDIR { - address 0x06c - access_mode RO -} - -register DINDIR { - address 0x06d - access_mode WO -} - -register FUNCTION1 { - address 0x06e - access_mode RW -} - -register STACK { - address 0x06f - access_mode RO -} - -/* - * Board Control (p. 3-43) - */ -register BCTL { - address 0x084 - access_mode RW - bit ACE 0x08 - bit ENABLE 0x01 -} - -register DSCOMMAND0 { - address 0x084 - access_mode RW - bit CACHETHEN 0x80 - bit DPARCKEN 0x40 - bit MPARCKEN 0x20 - bit EXTREQLCK 0x10 - bit INTSCBRAMSEL 0x08 - bit RAMPS 0x04 - bit USCBSIZE32 0x02 - bit CIOPARCKEN 0x01 -} - -/* - * On the aic78X0 chips, Board Control is replaced by the DSCommand - * register (p. 4-64) - */ -register DSCOMMAND { - address 0x084 - access_mode RW - bit CACHETHEN 0x80 /* Cache Threshold enable */ - bit DPARCKEN 0x40 /* Data Parity Check Enable */ - bit MPARCKEN 0x20 /* Memory Parity Check Enable */ - bit EXTREQLCK 0x10 /* External Request Lock */ -} - -/* - * Bus On/Off Time (p. 3-44) - */ -register BUSTIME { - address 0x085 - access_mode RW - mask BOFF 0xf0 - mask BON 0x0f -} - -/* - * Bus Speed (p. 3-45) - */ -register BUSSPD { - address 0x086 - access_mode RW - mask DFTHRSH 0xc0 - mask STBOFF 0x38 - mask STBON 0x07 - mask DFTHRSH_100 0xc0 -} - -/* - * Host Control (p. 3-47) R/W - * Overall host control of the device. - */ -register HCNTRL { - address 0x087 - access_mode RW - bit POWRDN 0x40 - bit SWINT 0x10 - bit IRQMS 0x08 - bit PAUSE 0x04 - bit INTEN 0x02 - bit CHIPRST 0x01 - bit CHIPRSTACK 0x01 -} - -/* - * Host Address (p. 3-48) - * This register contains the address of the byte about - * to be transferred across the host bus. - */ -register HADDR { - address 0x088 - size 4 - access_mode RW -} - -register HCNT { - address 0x08c - size 3 - access_mode RW -} - -/* - * SCB Pointer (p. 3-49) - * Gate one of the four SCBs into the SCBARRAY window. - */ -register SCBPTR { - address 0x090 - access_mode RW -} - -/* - * Interrupt Status (p. 3-50) - * Status for system interrupts - */ -register INTSTAT { - address 0x091 - access_mode RW - bit BRKADRINT 0x08 - bit SCSIINT 0x04 - bit CMDCMPLT 0x02 - bit SEQINT 0x01 - mask BAD_PHASE SEQINT /* unknown scsi bus phase */ - mask SEND_REJECT 0x10|SEQINT /* sending a message reject */ - mask NO_IDENT 0x20|SEQINT /* no IDENTIFY after reconnect*/ - mask NO_MATCH 0x30|SEQINT /* no cmd match for reconnect */ - mask EXTENDED_MSG 0x40|SEQINT /* Extended message received */ - mask WIDE_RESIDUE 0x50|SEQINT /* need kernel to back up */ - /* the SG array for us */ - mask REJECT_MSG 0x60|SEQINT /* Reject message received */ - mask BAD_STATUS 0x70|SEQINT /* Bad status from target */ - mask RESIDUAL 0x80|SEQINT /* Residual byte count != 0 */ - mask AWAITING_MSG 0xa0|SEQINT /* - * Kernel requested to specify - * a message to this target - * (command was null), so tell - * it that it can fill the - * message buffer. - */ - mask SEQ_SG_FIXUP 0xb0|SEQINT /* need help with fixing up - * the sg array pointer after - * a phasemis with no valid - * sg elements in the shadow - * pipeline. - */ - mask TRACEPOINT2 0xc0|SEQINT - mask MSGIN_PHASEMIS 0xd0|SEQINT /* - * Target changed phase on us - * when we were expecting - * another msgin byte. - */ - mask DATA_OVERRUN 0xe0|SEQINT /* - * Target attempted to write - * beyond the bounds of its - * command. - */ - - mask SEQINT_MASK 0xf0|SEQINT /* SEQINT Status Codes */ - mask INT_PEND (BRKADRINT|SEQINT|SCSIINT|CMDCMPLT) -} - -/* - * Hard Error (p. 3-53) - * Reporting of catastrophic errors. You usually cannot recover from - * these without a full board reset. - */ -register ERROR { - address 0x092 - access_mode RO - bit CIOPARERR 0x80 /* Ultra2 only */ - bit PCIERRSTAT 0x40 /* PCI only */ - bit MPARERR 0x20 /* PCI only */ - bit DPARERR 0x10 /* PCI only */ - bit SQPARERR 0x08 - bit ILLOPCODE 0x04 - bit ILLSADDR 0x02 - bit DSCTMOUT 0x02 /* Ultra3 only */ - bit ILLHADDR 0x01 -} - -/* - * Clear Interrupt Status (p. 3-52) - */ -register CLRINT { - address 0x092 - access_mode WO - bit CLRPARERR 0x10 /* PCI only */ - bit CLRBRKADRINT 0x08 - bit CLRSCSIINT 0x04 - bit CLRCMDINT 0x02 - bit CLRSEQINT 0x01 -} - -register DFCNTRL { - address 0x093 - access_mode RW - bit PRELOADEN 0x80 /* aic7890 only */ - bit WIDEODD 0x40 - bit SCSIEN 0x20 - bit SDMAEN 0x10 - bit SDMAENACK 0x10 - bit HDMAEN 0x08 - bit HDMAENACK 0x08 - bit DIRECTION 0x04 - bit FIFOFLUSH 0x02 - bit FIFORESET 0x01 -} - -register DFSTATUS { - address 0x094 - access_mode RO - bit PRELOAD_AVAIL 0x80 - bit DWORDEMP 0x20 - bit MREQPEND 0x10 - bit HDONE 0x08 - bit DFTHRESH 0x04 - bit FIFOFULL 0x02 - bit FIFOEMP 0x01 -} - -register DFDAT { - address 0x099 - access_mode RW -} - -/* - * SCB Auto Increment (p. 3-59) - * Byte offset into the SCB Array and an optional bit to allow auto - * incrementing of the address during download and upload operations - */ -register SCBCNT { - address 0x09a - access_mode RW - bit SCBAUTO 0x80 - mask SCBCNT_MASK 0x1f -} - -/* - * Queue In FIFO (p. 3-60) - * Input queue for queued SCBs (commands that the seqencer has yet to start) - */ -register QINFIFO { - address 0x09b - access_mode RW -} - -/* - * Queue In Count (p. 3-60) - * Number of queued SCBs - */ -register QINCNT { - address 0x09c - access_mode RO -} - -/* - * SCSIDATL IMAGE Register (p. 5-104) - * Write to this register also go to SCSIDATL but this register will preserve - * the data for later reading as long as the SCSIDATL_IMGEN bit in the - * OPTIONMODE register is set. - */ -register SCSIDATL_IMG { - address 0x09c - access_mode RW -} - -/* - * Queue Out FIFO (p. 3-61) - * Queue of SCBs that have completed and await the host - */ -register QOUTFIFO { - address 0x09d - access_mode WO -} - -/* - * CRC Control 1 Register (p. 5-105) - * Control bits for the Ultra 160/m CRC facilities - */ -register CRCCONTROL1 { - address 0x09d - access_mode RW - bit CRCONSEEN 0x80 /* CRC ON Single Edge ENable */ - bit CRCVALCHKEN 0x40 /* CRC Value Check Enable */ - bit CRCENDCHKEN 0x20 /* CRC End Check Enable */ - bit CRCREQCHKEN 0x10 - bit TARGCRCENDEN 0x08 /* Enable End CRC transfer when target */ - bit TARGCRCCNTEN 0x04 /* Enable CRC transfer when target */ -} - -/* - * Queue Out Count (p. 3-61) - * Number of queued SCBs in the Out FIFO - */ -register QOUTCNT { - address 0x09e - access_mode RO -} - -/* - * SCSI Phase Register (p. 5-106) - * Current bus phase - */ -register SCSIPHASE { - address 0x09e - access_mode RO - bit SP_STATUS 0x20 - bit SP_COMMAND 0x10 - bit SP_MSG_IN 0x08 - bit SP_MSG_OUT 0x04 - bit SP_DATA_IN 0x02 - bit SP_DATA_OUT 0x01 -} - -/* - * Special Function - */ -register SFUNCT { - address 0x09f - access_mode RW - bit ALT_MODE 0x80 -} - -/* - * SCB Definition (p. 5-4) - */ -scb { - address 0x0a0 - SCB_CONTROL { - size 1 - bit MK_MESSAGE 0x80 - bit DISCENB 0x40 - bit TAG_ENB 0x20 - bit DISCONNECTED 0x04 - mask SCB_TAG_TYPE 0x03 - } - SCB_TCL { - size 1 - bit SELBUSB 0x08 - mask TID 0xf0 - mask LID 0x07 - } - SCB_TARGET_STATUS { - size 1 - } - SCB_SGCOUNT { - size 1 - } - SCB_SGPTR { - size 4 - } - SCB_RESID_SGCNT { - size 1 - } - SCB_RESID_DCNT { - size 3 - } - SCB_DATAPTR { - size 4 - } - SCB_DATACNT { - /* - * Really only 3 bytes, but padded to make - * the kernel's job easier. - */ - size 4 - } - SCB_CMDPTR { - size 4 - } - SCB_CMDLEN { - size 1 - } - SCB_TAG { - size 1 - } - SCB_NEXT { - size 1 - } - SCB_PREV { - size 1 - } - SCB_BUSYTARGETS { - size 4 - } -} - -const SG_SIZEOF 0x08 /* sizeof(struct ahc_dma) */ - -/* --------------------- AHA-2840-only definitions -------------------- */ - -register SEECTL_2840 { - address 0x0c0 - access_mode RW - bit CS_2840 0x04 - bit CK_2840 0x02 - bit DO_2840 0x01 -} - -register STATUS_2840 { - address 0x0c1 - access_mode RW - bit EEPROM_TF 0x80 - mask BIOS_SEL 0x60 - mask ADSEL 0x1e - bit DI_2840 0x01 -} - -/* --------------------- AIC-7870-only definitions -------------------- */ - -register DSPCISTATUS { - address 0x086 - mask DFTHRSH_100 0xc0 -} - -register CCHADDR { - address 0x0E0 - size 8 -} - -register CCHCNT { - address 0x0E8 -} - -register CCSGRAM { - address 0x0E9 -} - -register CCSGADDR { - address 0x0EA -} - -register CCSGCTL { - address 0x0EB - bit CCSGDONE 0x80 - bit CCSGEN 0x08 - bit FLAG 0x02 - bit CCSGRESET 0x01 -} - -register CCSCBCNT { - address 0xEF -} - -register CCSCBCTL { - address 0x0EE - bit CCSCBDONE 0x80 - bit ARRDONE 0x40 /* SCB Array prefetch done */ - bit CCARREN 0x10 - bit CCSCBEN 0x08 - bit CCSCBDIR 0x04 - bit CCSCBRESET 0x01 -} - -register CCSCBADDR { - address 0x0ED -} - -register CCSCBRAM { - address 0xEC -} - -register CCSCBPTR { - address 0x0F1 -} - -register HNSCB_QOFF { - address 0x0F4 -} - -register HESCB_QOFF { - address 0x0F5 -} - -register SNSCB_QOFF { - address 0x0F6 -} - -register SESCB_QOFF { - address 0x0F7 -} - -register SDSCB_QOFF { - address 0x0F8 -} - -register QOFF_CTLSTA { - address 0x0FA - bit ESTABLISH_SCB_AVAIL 0x80 - bit SCB_AVAIL 0x40 - bit SNSCB_ROLLOVER 0x20 - bit SDSCB_ROLLOVER 0x10 - bit SESCB_ROLLOVER 0x08 - mask SCB_QSIZE 0x07 - mask SCB_QSIZE_256 0x06 -} - -register DFF_THRSH { - address 0x0FB - mask WR_DFTHRSH 0x70 - mask RD_DFTHRSH 0x07 - mask RD_DFTHRSH_MIN 0x00 - mask RD_DFTHRSH_25 0x01 - mask RD_DFTHRSH_50 0x02 - mask RD_DFTHRSH_63 0x03 - mask RD_DFTHRSH_75 0x04 - mask RD_DFTHRSH_85 0x05 - mask RD_DFTHRSH_90 0x06 - mask RD_DFTHRSH_MAX 0x07 - mask WR_DFTHRSH_MIN 0x00 - mask WR_DFTHRSH_25 0x10 - mask WR_DFTHRSH_50 0x20 - mask WR_DFTHRSH_63 0x30 - mask WR_DFTHRSH_75 0x40 - mask WR_DFTHRSH_85 0x50 - mask WR_DFTHRSH_90 0x60 - mask WR_DFTHRSH_MAX 0x70 -} - -register SG_CACHEPTR { - access_mode RW - address 0x0fc - mask SG_USER_DATA 0xfc - bit LAST_SEG 0x02 - bit LAST_SEG_DONE 0x01 -} - -register BRDCTL { - address 0x01d - bit BRDDAT7 0x80 - bit BRDDAT6 0x40 - bit BRDDAT5 0x20 - bit BRDSTB 0x10 - bit BRDCS 0x08 - bit BRDRW 0x04 - bit BRDCTL1 0x02 - bit BRDCTL0 0x01 - /* 7890 Definitions */ - bit BRDDAT4 0x10 - bit BRDDAT3 0x08 - bit BRDDAT2 0x04 - bit BRDRW_ULTRA2 0x02 - bit BRDSTB_ULTRA2 0x01 -} - -/* - * Serial EEPROM Control (p. 4-92 in 7870 Databook) - * Controls the reading and writing of an external serial 1-bit - * EEPROM Device. In order to access the serial EEPROM, you must - * first set the SEEMS bit that generates a request to the memory - * port for access to the serial EEPROM device. When the memory - * port is not busy servicing another request, it reconfigures - * to allow access to the serial EEPROM. When this happens, SEERDY - * gets set high to verify that the memory port access has been - * granted. - * - * After successful arbitration for the memory port, the SEECS bit of - * the SEECTL register is connected to the chip select. The SEECK, - * SEEDO, and SEEDI are connected to the clock, data out, and data in - * lines respectively. The SEERDY bit of SEECTL is useful in that it - * gives us an 800 nsec timer. After a write to the SEECTL register, - * the SEERDY goes high 800 nsec later. The one exception to this is - * when we first request access to the memory port. The SEERDY goes - * high to signify that access has been granted and, for this case, has - * no implied timing. - * - * See 93cx6.c for detailed information on the protocol necessary to - * read the serial EEPROM. - */ -register SEECTL { - address 0x01e - bit EXTARBACK 0x80 - bit EXTARBREQ 0x40 - bit SEEMS 0x20 - bit SEERDY 0x10 - bit SEECS 0x08 - bit SEECK 0x04 - bit SEEDO 0x02 - bit SEEDI 0x01 -} -/* ---------------------- Scratch RAM Offsets ------------------------- */ -/* These offsets are either to values that are initialized by the board's - * BIOS or are specified by the sequencer code. - * - * The host adapter card (at least the BIOS) uses 20-2f for SCSI - * device information, 32-33 and 5a-5f as well. As it turns out, the - * BIOS trashes 20-2f, writing the synchronous negotiation results - * on top of the BIOS values, so we re-use those for our per-target - * scratchspace (actually a value that can be copied directly into - * SCSIRATE). The kernel driver will enable synchronous negotiation - * for all targets that have a value other than 0 in the lower four - * bits of the target scratch space. This should work regardless of - * whether the bios has been installed. - */ - -scratch_ram { - address 0x020 - - /* - * 1 byte per target starting at this address for configuration values - */ - TARG_SCSIRATE { - size 16 - } - /* - * Bit vector of targets that have ULTRA enabled. - */ - ULTRA_ENB { - size 2 - } - /* - * Bit vector of targets that have disconnection disabled. - */ - DISC_DSB { - size 2 - } - /* - * Single byte buffer used to designate the type or message - * to send to a target. - */ - MSG_OUT { - size 1 - } - /* Parameters for DMA Logic */ - DMAPARAMS { - size 1 - bit PRELOADEN 0x80 - bit WIDEODD 0x40 - bit SCSIEN 0x20 - bit SDMAEN 0x10 - bit SDMAENACK 0x10 - bit HDMAEN 0x08 - bit HDMAENACK 0x08 - bit DIRECTION 0x04 - bit FIFOFLUSH 0x02 - bit FIFORESET 0x01 - } - SEQ_FLAGS { - size 1 - bit IDENTIFY_SEEN 0x80 - bit SCBPTR_VALID 0x20 - bit DPHASE 0x10 - bit AMTARGET 0x08 - bit WIDE_BUS 0x02 - bit TWIN_BUS 0x01 - } - /* - * Temporary storage for the - * target/channel/lun of a - * reconnecting target - */ - SAVED_TCL { - size 1 - } - /* Working value of the number of SG segments left */ - SG_COUNT { - size 1 - } - /* Working value of SG pointer */ - SG_NEXT { - size 4 - } - /* - * The last bus phase as seen by the sequencer. - */ - LASTPHASE { - size 1 - bit CDI 0x80 - bit IOI 0x40 - bit MSGI 0x20 - mask PHASE_MASK CDI|IOI|MSGI - mask P_DATAOUT 0x00 - mask P_DATAIN IOI - mask P_COMMAND CDI - mask P_MESGOUT CDI|MSGI - mask P_STATUS CDI|IOI - mask P_MESGIN CDI|IOI|MSGI - mask P_BUSFREE 0x01 - } - /* - * head of list of SCBs awaiting - * selection - */ - WAITING_SCBH { - size 1 - } - /* - * head of list of SCBs that are - * disconnected. Used for SCB - * paging. - */ - DISCONNECTED_SCBH { - size 1 - } - /* - * head of list of SCBs that are - * not in use. Used for SCB paging. - */ - FREE_SCBH { - size 1 - } - /* - * Address of the hardware scb array in the host. - */ - HSCB_ADDR { - size 4 - } - /* - * Address of the 256 byte array storing the SCBID of outstanding - * untagged SCBs indexed by TCL. - */ - SCBID_ADDR { - size 4 - } - /* - * Address of the array of command descriptors used to store - * information about incoming selections. - */ - TMODE_CMDADDR { - size 4 - } - KERNEL_QINPOS { - size 1 - } - QINPOS { - size 1 - } - QOUTPOS { - size 1 - } - /* - * Offset into the command descriptor array for the next - * available desciptor to use. - */ - TMODE_CMDADDR_NEXT { - size 1 - } - ARG_1 { - size 1 - mask SEND_MSG 0x80 - mask SEND_SENSE 0x40 - mask SEND_REJ 0x20 - mask MSGOUT_PHASEMIS 0x10 - alias RETURN_1 - } - ARG_2 { - size 1 - alias RETURN_2 - } - - /* - * Snapshot of MSG_OUT taken after each message is sent. - */ - LAST_MSG { - size 1 - } - - /* - * Number of times we have filled the CCSGRAM with prefetched - * SG elements. - */ - PREFETCH_CNT { - size 1 - } - - - /* - * These are reserved registers in the card's scratch ram. Some of - * the values are specified in the AHA2742 technical reference manual - * and are initialized by the BIOS at boot time. - */ - SCSICONF { - address 0x05a - size 1 - bit TERM_ENB 0x80 - bit RESET_SCSI 0x40 - mask HSCSIID 0x07 /* our SCSI ID */ - mask HWSCSIID 0x0f /* our SCSI ID if Wide Bus */ - } - HOSTCONF { - address 0x05d - size 1 - } - HA_274_BIOSCTRL { - address 0x05f - size 1 - mask BIOSMODE 0x30 - mask BIOSDISABLED 0x30 - bit CHANNEL_B_PRIMARY 0x08 - } - /* - * Per target SCSI offset values for Ultra2 controllers. - */ - TARG_OFFSET { - address 0x070 - size 16 - } -} - -const SCB_LIST_NULL 0xff - -const CCSGADDR_MAX 0x80 -const CCSGRAM_MAXSEGS 16 - -/* Offsets into the SCBID array where different data is stored */ -const UNTAGGEDSCB_OFFSET 0 -const QOUTFIFO_OFFSET 1 -const QINFIFO_OFFSET 2 - -/* WDTR Message values */ -const BUS_8_BIT 0x00 -const BUS_16_BIT 0x01 -const BUS_32_BIT 0x02 - -/* Offset maximums */ -const MAX_OFFSET_8BIT 0x0f -const MAX_OFFSET_16BIT 0x08 -const MAX_OFFSET_ULTRA2 0x7f -const HOST_MSG 0xff - -/* Target mode command processing constants */ -const CMD_GROUP_CODE_SHIFT 0x05 -const CMD_GROUP0_BYTE_DELTA -4 -const CMD_GROUP2_BYTE_DELTA -6 -const CMD_GROUP4_BYTE_DELTA 4 -const CMD_GROUP5_BYTE_DELTA 11 - -/* - * Downloaded (kernel inserted) constants - */ - -/* - * Number of command descriptors in the command descriptor array. - */ -const TMODE_NUMCMDS download diff --git a/drivers/scsi/aic7xxx_old/aic7xxx.seq b/drivers/scsi/aic7xxx_old/aic7xxx.seq deleted file mode 100644 index dc3bb81cff0..00000000000 --- a/drivers/scsi/aic7xxx_old/aic7xxx.seq +++ /dev/null @@ -1,1539 +0,0 @@ -/* - * Adaptec 274x/284x/294x device driver firmware for Linux and FreeBSD. - * - * Copyright (c) 1994-1999 Justin Gibbs. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions, and the following disclaimer, - * without modification, immediately at the beginning of the file. - * 2. The name of the author may not be used to endorse or promote products - * derived from this software without specific prior written permission. - * - * Where this Software is combined with software released under the terms of - * the GNU General Public License (GPL) and the terms of the GPL would require the - * combined work to also be released under the terms of the GPL, the terms - * and conditions of this License will apply in addition to those of the - * GPL with the exception of any terms or conditions of this License that - * conflict with, or are expressly prohibited by, the GPL. - * - * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND - * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR - * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS - * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) - * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT - * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY - * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF - * SUCH DAMAGE. - * - * $Id: aic7xxx.seq,v 1.77 1998/06/28 02:58:57 gibbs Exp $ - */ - -#include "aic7xxx.reg" -#include "scsi_message.h" - -/* - * A few words on the waiting SCB list: - * After starting the selection hardware, we check for reconnecting targets - * as well as for our selection to complete just in case the reselection wins - * bus arbitration. The problem with this is that we must keep track of the - * SCB that we've already pulled from the QINFIFO and started the selection - * on just in case the reselection wins so that we can retry the selection at - * a later time. This problem cannot be resolved by holding a single entry - * in scratch ram since a reconnecting target can request sense and this will - * create yet another SCB waiting for selection. The solution used here is to - * use byte 27 of the SCB as a pseudo-next pointer and to thread a list - * of SCBs that are awaiting selection. Since 0-0xfe are valid SCB indexes, - * SCB_LIST_NULL is 0xff which is out of range. An entry is also added to - * this list every time a request sense occurs or after completing a non-tagged - * command for which a second SCB has been queued. The sequencer will - * automatically consume the entries. - */ - -reset: - clr SCSISIGO; /* De-assert BSY */ - and SXFRCTL1, ~BITBUCKET; - /* Always allow reselection */ - mvi SCSISEQ, ENRSELI|ENAUTOATNP; - - if ((p->features & AHC_CMD_CHAN) != 0) { - /* Ensure that no DMA operations are in progress */ - clr CCSGCTL; - clr CCSCBCTL; - } - - call clear_target_state; -poll_for_work: - and SXFRCTL0, ~SPIOEN; - if ((p->features & AHC_QUEUE_REGS) == 0) { - mov A, QINPOS; - } -poll_for_work_loop: - if ((p->features & AHC_QUEUE_REGS) == 0) { - and SEQCTL, ~PAUSEDIS; - } - test SSTAT0, SELDO|SELDI jnz selection; - test SCSISEQ, ENSELO jnz poll_for_work; - if ((p->features & AHC_TWIN) != 0) { - /* - * Twin channel devices cannot handle things like SELTO - * interrupts on the "background" channel. So, if we - * are selecting, keep polling the current channel util - * either a selection or reselection occurs. - */ - xor SBLKCTL,SELBUSB; /* Toggle to the other bus */ - test SSTAT0, SELDO|SELDI jnz selection; - test SCSISEQ, ENSELO jnz poll_for_work; - xor SBLKCTL,SELBUSB; /* Toggle back */ - } - cmp WAITING_SCBH,SCB_LIST_NULL jne start_waiting; -test_queue: - /* Has the driver posted any work for us? */ - if ((p->features & AHC_QUEUE_REGS) != 0) { - test QOFF_CTLSTA, SCB_AVAIL jz poll_for_work_loop; - mov NONE, SNSCB_QOFF; - inc QINPOS; - } else { - or SEQCTL, PAUSEDIS; - cmp KERNEL_QINPOS, A je poll_for_work_loop; - inc QINPOS; - and SEQCTL, ~PAUSEDIS; - } - -/* - * We have at least one queued SCB now and we don't have any - * SCBs in the list of SCBs awaiting selection. If we have - * any SCBs available for use, pull the tag from the QINFIFO - * and get to work on it. - */ - if ((p->flags & AHC_PAGESCBS) != 0) { - mov ALLZEROS call get_free_or_disc_scb; - } - -dequeue_scb: - add A, -1, QINPOS; - mvi QINFIFO_OFFSET call fetch_byte; - - if ((p->flags & AHC_PAGESCBS) == 0) { - /* In the non-paging case, the SCBID == hardware SCB index */ - mov SCBPTR, RETURN_2; - } -dma_queued_scb: -/* - * DMA the SCB from host ram into the current SCB location. - */ - mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; - mov RETURN_2 call dma_scb; - -/* - * Preset the residual fields in case we never go through a data phase. - * This isn't done by the host so we can avoid a DMA to clear these - * fields for the normal case of I/O that completes without underrun - * or overrun conditions. - */ - if ((p->features & AHC_CMD_CHAN) != 0) { - bmov SCB_RESID_DCNT, SCB_DATACNT, 3; - } else { - mov SCB_RESID_DCNT[0],SCB_DATACNT[0]; - mov SCB_RESID_DCNT[1],SCB_DATACNT[1]; - mov SCB_RESID_DCNT[2],SCB_DATACNT[2]; - } - mov SCB_RESID_SGCNT, SCB_SGCOUNT; - -start_scb: - /* - * Place us on the waiting list in case our selection - * doesn't win during bus arbitration. - */ - mov SCB_NEXT,WAITING_SCBH; - mov WAITING_SCBH, SCBPTR; -start_waiting: - /* - * Pull the first entry off of the waiting SCB list. - */ - mov SCBPTR, WAITING_SCBH; - call start_selection; - jmp poll_for_work; - -start_selection: - if ((p->features & AHC_TWIN) != 0) { - and SINDEX,~SELBUSB,SBLKCTL;/* Clear channel select bit */ - and A,SELBUSB,SCB_TCL; /* Get new channel bit */ - or SINDEX,A; - mov SBLKCTL,SINDEX; /* select channel */ - } -initialize_scsiid: - if ((p->features & AHC_ULTRA2) != 0) { - and A, TID, SCB_TCL; /* Get target ID */ - and SCSIID_ULTRA2, OID; /* Clear old target */ - or SCSIID_ULTRA2, A; - } else { - and A, TID, SCB_TCL; /* Get target ID */ - and SCSIID, OID; /* Clear old target */ - or SCSIID, A; - } - mov SCSIDATL, ALLZEROS; /* clear out the latched */ - /* data register, this */ - /* fixes a bug on some */ - /* controllers where the */ - /* last byte written to */ - /* this register can leak */ - /* onto the data bus at */ - /* bad times, such as during */ - /* selection timeouts */ - mvi SCSISEQ, ENSELO|ENAUTOATNO|ENRSELI|ENAUTOATNP ret; - -/* - * Initialize Ultra mode setting and clear the SCSI channel. - * SINDEX should contain any additional bit's the client wants - * set in SXFRCTL0. - */ -initialize_channel: - or SXFRCTL0, CLRSTCNT|CLRCHN, SINDEX; - if ((p->features & AHC_ULTRA) != 0) { -ultra: - mvi SINDEX, ULTRA_ENB+1; - test SAVED_TCL, 0x80 jnz ultra_2; /* Target ID > 7 */ - dec SINDEX; -ultra_2: - mov FUNCTION1,SAVED_TCL; - mov A,FUNCTION1; - test SINDIR, A jz ndx_dtr; - or SXFRCTL0, FAST20; - } -/* - * Initialize SCSIRATE with the appropriate value for this target. - * The SCSIRATE settings for each target are stored in an array - * based at TARG_SCSIRATE. - */ -ndx_dtr: - shr A,4,SAVED_TCL; - if ((p->features & AHC_TWIN) != 0) { - test SBLKCTL,SELBUSB jz ndx_dtr_2; - or SAVED_TCL, SELBUSB; - or A,0x08; /* Channel B entries add 8 */ -ndx_dtr_2: - } - - if ((p->features & AHC_ULTRA2) != 0) { - add SINDEX, TARG_OFFSET, A; - mov SCSIOFFSET, SINDIR; - } - - add SINDEX,TARG_SCSIRATE,A; - mov SCSIRATE,SINDIR ret; - - -selection: - test SSTAT0,SELDO jnz select_out; -/* - * Reselection has been initiated by a target. Make a note that we've been - * reselected, but haven't seen an IDENTIFY message from the target yet. - */ -initiator_reselect: - mvi CLRSINT0, CLRSELDI; - /* XXX test for and handle ONE BIT condition */ - and SAVED_TCL, SELID_MASK, SELID; - mvi CLRSINT1,CLRBUSFREE; - or SIMODE1, ENBUSFREE; /* - * We aren't expecting a - * bus free, so interrupt - * the kernel driver if it - * happens. - */ - mvi SPIOEN call initialize_channel; - mvi MSG_OUT, MSG_NOOP; /* No message to send */ - jmp ITloop; - -/* - * After the selection, remove this SCB from the "waiting SCB" - * list. This is achieved by simply moving our "next" pointer into - * WAITING_SCBH. Our next pointer will be set to null the next time this - * SCB is used, so don't bother with it now. - */ -select_out: - /* Turn off the selection hardware */ - mvi SCSISEQ, ENRSELI|ENAUTOATNP; /* - * ATN on parity errors - * for "in" phases - */ - mvi CLRSINT0, CLRSELDO; - mov SCBPTR, WAITING_SCBH; - mov WAITING_SCBH,SCB_NEXT; - mov SAVED_TCL, SCB_TCL; - mvi CLRSINT1,CLRBUSFREE; - or SIMODE1, ENBUSFREE; /* - * We aren't expecting a - * bus free, so interrupt - * the kernel driver if it - * happens. - */ - mvi SPIOEN call initialize_channel; -/* - * As soon as we get a successful selection, the target should go - * into the message out phase since we have ATN asserted. - */ - mvi MSG_OUT, MSG_IDENTIFYFLAG; - or SEQ_FLAGS, IDENTIFY_SEEN; - -/* - * Main loop for information transfer phases. Wait for the target - * to assert REQ before checking MSG, C/D and I/O for the bus phase. - */ -ITloop: - call phase_lock; - - mov A, LASTPHASE; - - test A, ~P_DATAIN jz p_data; - cmp A,P_COMMAND je p_command; - cmp A,P_MESGOUT je p_mesgout; - cmp A,P_STATUS je p_status; - cmp A,P_MESGIN je p_mesgin; - - mvi INTSTAT,BAD_PHASE; /* unknown phase - signal driver */ - jmp ITloop; /* Try reading the bus again. */ - -await_busfree: - and SIMODE1, ~ENBUSFREE; - call clear_target_state; - mov NONE, SCSIDATL; /* Ack the last byte */ - and SXFRCTL0, ~SPIOEN; - test SSTAT1,REQINIT|BUSFREE jz .; - test SSTAT1, BUSFREE jnz poll_for_work; - mvi INTSTAT, BAD_PHASE; - -clear_target_state: - /* - * We assume that the kernel driver may reset us - * at any time, even in the middle of a DMA, so - * clear DFCNTRL too. - */ - clr DFCNTRL; - - /* - * We don't know the target we will connect to, - * so default to narrow transfers to avoid - * parity problems. - */ - if ((p->features & AHC_ULTRA2) != 0) { - bmov SCSIRATE, ALLZEROS, 2; - } else { - clr SCSIRATE; - and SXFRCTL0, ~(FAST20); - } - mvi LASTPHASE, P_BUSFREE; - /* clear target specific flags */ - clr SEQ_FLAGS ret; - - -data_phase_reinit: -/* - * If we re-enter the data phase after going through another phase, the - * STCNT may have been cleared, so restore it from the residual field. - * On Ultra2, we have to put it into the HCNT field because we have to - * drop the data down into the shadow layer via the preload ability. - */ - if ((p->features & AHC_ULTRA2) != 0) { - bmov HADDR, SHADDR, 4; - bmov HCNT, SCB_RESID_DCNT, 3; - } - if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { - bmov STCNT, SCB_RESID_DCNT, 3; - } - if ((p->features & AHC_CMD_CHAN) == 0) { - mvi DINDEX, STCNT; - mvi SCB_RESID_DCNT call bcopy_3; - } - jmp data_phase_loop; -p_data: - if ((p->features & AHC_ULTRA2) != 0) { - mvi DMAPARAMS, PRELOADEN|SCSIEN|HDMAEN; - } else { - mvi DMAPARAMS, WIDEODD|SCSIEN|SDMAEN|HDMAEN|FIFORESET; - } - test LASTPHASE, IOI jnz . + 2; - or DMAPARAMS, DIRECTION; - call assert; /* - * Ensure entering a data - * phase is okay - seen identify, etc. - */ - if ((p->features & AHC_CMD_CHAN) != 0) { - mvi CCSGADDR, CCSGADDR_MAX; - } - - test SEQ_FLAGS, DPHASE jnz data_phase_reinit; - or SEQ_FLAGS, DPHASE; /* we've seen a data phase */ - /* - * Initialize the DMA address and counter from the SCB. - * Also set SG_COUNT and SG_NEXT in memory since we cannot - * modify the values in the SCB itself until we see a - * save data pointers message. - */ - if ((p->features & AHC_CMD_CHAN) != 0) { - bmov HADDR, SCB_DATAPTR, 7; - bmov SG_COUNT, SCB_SGCOUNT, 5; - if ((p->features & AHC_ULTRA2) == 0) { - bmov STCNT, HCNT, 3; - } - } else { - mvi DINDEX, HADDR; - mvi SCB_DATAPTR call bcopy_7; - call set_stcnt_from_hcnt; - mvi DINDEX, SG_COUNT; - mvi SCB_SGCOUNT call bcopy_5; - } -data_phase_loop: - /* Guard against overruns */ - test SG_COUNT, 0xff jnz data_phase_inbounds; -/* - * Turn on 'Bit Bucket' mode, set the transfer count to - * 16meg and let the target run until it changes phase. - * When the transfer completes, notify the host that we - * had an overrun. - */ - or SXFRCTL1,BITBUCKET; - and DMAPARAMS, ~(HDMAEN|SDMAEN); - if ((p->features & AHC_ULTRA2) != 0) { - bmov HCNT, ALLONES, 3; - } - if ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895) { - bmov STCNT, ALLONES, 3; - } - if ((p->features & AHC_CMD_CHAN) == 0) { - mvi STCNT[0], 0xFF; - mvi STCNT[1], 0xFF; - mvi STCNT[2], 0xFF; - } - -data_phase_inbounds: -/* If we are the last SG block, tell the hardware. */ - if ((p->features & AHC_ULTRA2) != 0) { - shl A, 2, SG_COUNT; - cmp SG_COUNT,0x01 jne data_phase_wideodd; - or A, LAST_SEG; - } else { - cmp SG_COUNT,0x01 jne data_phase_wideodd; - and DMAPARAMS, ~WIDEODD; - } -data_phase_wideodd: - if ((p->features & AHC_ULTRA2) != 0) { - mov SG_CACHEPTR, A; - mov DFCNTRL, DMAPARAMS; /* start the operation */ - test SXFRCTL1, BITBUCKET jnz data_phase_overrun; -u2_preload_wait: - test SSTAT1, PHASEMIS jnz u2_phasemis; - test DFSTATUS, PRELOAD_AVAIL jz u2_preload_wait; - } else { - mov DMAPARAMS call dma; -data_phase_dma_done: -/* Go tell the host about any overruns */ - test SXFRCTL1,BITBUCKET jnz data_phase_overrun; - -/* Exit if we had an underrun. dma clears SINDEX in this case. */ - test SINDEX,0xff jz data_phase_finish; - } -/* - * Advance the scatter-gather pointers - */ -sg_advance: - if ((p->features & AHC_ULTRA2) != 0) { - cmp SG_COUNT, 0x01 je u2_data_phase_finish; - } else { - dec SG_COUNT; - test SG_COUNT, 0xff jz data_phase_finish; - } - - if ((p->features & AHC_CMD_CHAN) != 0) { - - /* - * Do we have any prefetch left??? - */ - cmp CCSGADDR, CCSGADDR_MAX jne prefetch_avail; - - /* - * Fetch MIN(CCSGADDR_MAX, (SG_COUNT * 8)) bytes. - */ - add A, -(CCSGRAM_MAXSEGS + 1), SG_COUNT; - mvi A, CCSGADDR_MAX; - jc . + 2; - shl A, 3, SG_COUNT; - mov CCHCNT, A; - bmov CCHADDR, SG_NEXT, 4; - mvi CCSGCTL, CCSGEN|CCSGRESET; - test CCSGCTL, CCSGDONE jz .; - and CCSGCTL, ~CCSGEN; - test CCSGCTL, CCSGEN jnz .; - mvi CCSGCTL, CCSGRESET; -prefetch_avail: - bmov HADDR, CCSGRAM, 8; - if ((p->features & AHC_ULTRA2) == 0) { - bmov STCNT, HCNT, 3; - } else { - dec SG_COUNT; - } - } else { - mvi DINDEX, HADDR; - mvi SG_NEXT call bcopy_4; - - mvi HCNT[0],SG_SIZEOF; - clr HCNT[1]; - clr HCNT[2]; - - or DFCNTRL, HDMAEN|DIRECTION|FIFORESET; - - call dma_finish; - -/* - * Copy data from FIFO into SCB data pointer and data count. - * This assumes that the SG segments are of the form: - * struct ahc_dma_seg { - * u_int32_t addr; four bytes, little-endian order - * u_int32_t len; four bytes, little endian order - * }; - */ - mvi DINDEX, HADDR; - call dfdat_in_7; - call set_stcnt_from_hcnt; - } -/* Advance the SG pointer */ - clr A; /* add sizeof(struct scatter) */ - add SG_NEXT[0],SG_SIZEOF; - adc SG_NEXT[1],A; - - if ((p->features & AHC_ULTRA2) != 0) { - jmp data_phase_loop; - } else { - test SSTAT1, REQINIT jz .; - test SSTAT1,PHASEMIS jz data_phase_loop; - } - - -/* - * We've loaded all of our segments into the preload layer. Now, we simply - * have to wait for it to finish or for us to get a phasemis. And, since - * we'll get a phasemis if we do finish, all we really need to do is wait - * for a phasemis then check if we did actually complete all the segments. - */ - if ((p->features & AHC_ULTRA2) != 0) { -u2_data_phase_finish: - test SSTAT1, PHASEMIS jnz u2_phasemis; - test SG_CACHEPTR, LAST_SEG_DONE jz u2_data_phase_finish; - clr SG_COUNT; - test SSTAT1, REQINIT jz .; - test SSTAT1, PHASEMIS jz data_phase_loop; -u2_phasemis: - call ultra2_dmafinish; - test SG_CACHEPTR, LAST_SEG_DONE jnz data_phase_finish; - test SSTAT2, SHVALID jnz u2_fixup_residual; - mvi INTSTAT, SEQ_SG_FIXUP; - jmp data_phase_finish; -u2_fixup_residual: - shr ARG_1, 2, SG_CACHEPTR; -u2_phasemis_loop: - and A, 0x3f, SG_COUNT; - cmp ARG_1, A je data_phase_finish; -/* - * Subtract SG_SIZEOF from the SG_NEXT pointer and add 1 to the SG_COUNT - */ - clr A; - add SG_NEXT[0], -SG_SIZEOF; - adc SG_NEXT[1], 0xff; - inc SG_COUNT; - jmp u2_phasemis_loop; - } - -data_phase_finish: -/* - * After a DMA finishes, save the SG and STCNT residuals back into the SCB - * We use STCNT instead of HCNT, since it's a reflection of how many bytes - * were transferred on the SCSI (as opposed to the host) bus. - */ - if ((p->features & AHC_CMD_CHAN) != 0) { - bmov SCB_RESID_DCNT, STCNT, 3; - mov SCB_RESID_SGCNT, SG_COUNT; - if ((p->features & AHC_ULTRA2) != 0) { - or SXFRCTL0, CLRSTCNT|CLRCHN; - } - } else { - mov SCB_RESID_DCNT[0],STCNT[0]; - mov SCB_RESID_DCNT[1],STCNT[1]; - mov SCB_RESID_DCNT[2],STCNT[2]; - mov SCB_RESID_SGCNT, SG_COUNT; - } - - jmp ITloop; - -data_phase_overrun: -/* - * Turn off BITBUCKET mode and notify the host - */ - if ((p->features & AHC_ULTRA2) != 0) { -/* - * Wait for the target to quit transferring data on the SCSI bus - */ - test SSTAT1, PHASEMIS jz .; - call ultra2_dmafinish; - } - and SXFRCTL1, ~BITBUCKET; - mvi INTSTAT,DATA_OVERRUN; - jmp ITloop; - - - - -/* - * Actually turn off the DMA hardware, save our current position into the - * proper residual variables, wait for the next REQ signal, then jump to - * the ITloop. Jumping to the ITloop ensures that if we happen to get - * brought into the data phase again (or are still in it after our last - * segment) that we will properly signal an overrun to the kernel. - */ - if ((p->features & AHC_ULTRA2) != 0) { -ultra2_dmafinish: - test DFCNTRL, DIRECTION jnz ultra2_dmahalt; - and DFCNTRL, ~SCSIEN; - test DFCNTRL, SCSIEN jnz .; - if ((p->bugs & AHC_BUG_AUTOFLUSH) != 0) { - or DFCNTRL, FIFOFLUSH; - } -ultra2_dmafifoflush: - if ((p->bugs & AHC_BUG_AUTOFLUSH) != 0) { - /* - * hardware bug alert! This needless set of jumps - * works around a glitch in the silicon. When the - * PCI DMA fifo goes empty, but there is still SCSI - * data to be flushed into the PCI DMA fifo (and from - * there on into main memory), the FIFOEMP bit will - * come on between the time when the PCI DMA buffer - * went empty and the next bit of data is copied from - * the SCSI fifo into the PCI fifo. It should only - * come on when both FIFOs (meaning the entire FIFO - * chain) are empty. Since it can take up to 4 cycles - * for new data to be copied from the SCSI fifo into - * the PCI fifo, testing for FIFOEMP status for 4 - * extra times gives the needed time for any - * remaining SCSI fifo data to be put in the PCI fifo - * before we declare it *truly* empty. - */ - test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; - test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; - test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; - test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; - } - test DFSTATUS, FIFOEMP jz ultra2_dmafifoflush; - test DFSTATUS, MREQPEND jnz .; -ultra2_dmahalt: - and DFCNTRL, ~(HDMAEN|SCSIEN); - test DFCNTRL, (HDMAEN|SCSIEN) jnz .; - ret; - } - -/* - * Command phase. Set up the DMA registers and let 'er rip. - */ -p_command: - call assert; - -/* - * Load HADDR and HCNT. - */ - if ((p->features & AHC_CMD_CHAN) != 0) { - bmov HADDR, SCB_CMDPTR, 5; - bmov HCNT[1], ALLZEROS, 2; - if ((p->features & AHC_ULTRA2) == 0) { - bmov STCNT, HCNT, 3; - } - } else { - mvi DINDEX, HADDR; - mvi SCB_CMDPTR call bcopy_5; - clr HCNT[1]; - clr HCNT[2]; - call set_stcnt_from_hcnt; - } - - if ((p->features & AHC_ULTRA2) == 0) { - mvi (SCSIEN|SDMAEN|HDMAEN|DIRECTION|FIFORESET) call dma; - } else { - mvi DFCNTRL, (PRELOADEN|SCSIEN|HDMAEN|DIRECTION); - test SSTAT0, SDONE jnz .; -p_command_dma_loop: - test SSTAT0, SDONE jnz p_command_ultra2_dma_done; - test SSTAT1,PHASEMIS jz p_command_dma_loop; /* ie. underrun */ -p_command_ultra2_dma_done: - test SCSISIGI, REQI jz p_command_ultra2_shutdown; - test SSTAT1, (PHASEMIS|REQINIT) jz p_command_ultra2_dma_done; -p_command_ultra2_shutdown: - and DFCNTRL, ~(HDMAEN|SCSIEN); - test DFCNTRL, (HDMAEN|SCSIEN) jnz .; - or SXFRCTL0, CLRSTCNT|CLRCHN; - } - jmp ITloop; - -/* - * Status phase. Wait for the data byte to appear, then read it - * and store it into the SCB. - */ -p_status: - call assert; - - mov SCB_TARGET_STATUS, SCSIDATL; - jmp ITloop; - -/* - * Message out phase. If MSG_OUT is 0x80, build I full indentify message - * sequence and send it to the target. In addition, if the MK_MESSAGE bit - * is set in the SCB_CONTROL byte, interrupt the host and allow it to send - * it's own message. - * - * If MSG_OUT is == HOST_MSG, also interrupt the host and take a message. - * This is done to allow the host to send messages outside of an identify - * sequence while protecting the seqencer from testing the MK_MESSAGE bit - * on an SCB that might not be for the current nexus. (For example, a - * BDR message in response to a bad reselection would leave us pointed to - * an SCB that doesn't have anything to do with the current target). - * Otherwise, treat MSG_OUT as a 1 byte message to send (abort, abort tag, - * bus device reset). - * - * When there are no messages to send, MSG_OUT should be set to MSG_NOOP, - * in case the target decides to put us in this phase for some strange - * reason. - */ -p_mesgout_retry: - or SCSISIGO,ATNO,LASTPHASE;/* turn on ATN for the retry */ -p_mesgout: - mov SINDEX, MSG_OUT; - cmp SINDEX, MSG_IDENTIFYFLAG jne p_mesgout_from_host; -p_mesgout_identify: - if ((p->features & AHC_WIDE) != 0) { - and SINDEX,0xf,SCB_TCL; /* lun */ - } else { - and SINDEX,0x7,SCB_TCL; /* lun */ - } - and A,DISCENB,SCB_CONTROL; /* mask off disconnect privilege */ - or SINDEX,A; /* or in disconnect privilege */ - or SINDEX,MSG_IDENTIFYFLAG; -p_mesgout_mk_message: - test SCB_CONTROL,MK_MESSAGE jz p_mesgout_tag; - mov SCSIDATL, SINDEX; /* Send the last byte */ - jmp p_mesgout_from_host + 1;/* Skip HOST_MSG test */ -/* - * Send a tag message if TAG_ENB is set in the SCB control block. - * Use SCB_TAG (the position in the kernel's SCB array) as the tag value. - */ -p_mesgout_tag: - test SCB_CONTROL,TAG_ENB jz p_mesgout_onebyte; - mov SCSIDATL, SINDEX; /* Send the identify message */ - call phase_lock; - cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; - and SCSIDATL,TAG_ENB|SCB_TAG_TYPE,SCB_CONTROL; - call phase_lock; - cmp LASTPHASE, P_MESGOUT jne p_mesgout_done; - mov SCB_TAG jmp p_mesgout_onebyte; -/* - * Interrupt the driver, and allow it to send a message - * if it asks. - */ -p_mesgout_from_host: - cmp SINDEX, HOST_MSG jne p_mesgout_onebyte; - mvi INTSTAT,AWAITING_MSG; - nop; - /* - * Did the host detect a phase change? - */ - cmp RETURN_1, MSGOUT_PHASEMIS je p_mesgout_done; - -p_mesgout_onebyte: - mvi CLRSINT1, CLRATNO; - mov SCSIDATL, SINDEX; - -/* - * If the next bus phase after ATN drops is a message out, it means - * that the target is requesting that the last message(s) be resent. - */ - call phase_lock; - cmp LASTPHASE, P_MESGOUT je p_mesgout_retry; - -p_mesgout_done: - mvi CLRSINT1,CLRATNO; /* Be sure to turn ATNO off */ - mov LAST_MSG, MSG_OUT; - cmp MSG_OUT, MSG_IDENTIFYFLAG jne . + 2; - and SCB_CONTROL, ~MK_MESSAGE; - mvi MSG_OUT, MSG_NOOP; /* No message left */ - jmp ITloop; - -/* - * Message in phase. Bytes are read using Automatic PIO mode. - */ -p_mesgin: - mvi ACCUM call inb_first; /* read the 1st message byte */ - - test A,MSG_IDENTIFYFLAG jnz mesgin_identify; - cmp A,MSG_DISCONNECT je mesgin_disconnect; - cmp A,MSG_SAVEDATAPOINTER je mesgin_sdptrs; - cmp ALLZEROS,A je mesgin_complete; - cmp A,MSG_RESTOREPOINTERS je mesgin_rdptrs; - cmp A,MSG_EXTENDED je mesgin_extended; - cmp A,MSG_MESSAGE_REJECT je mesgin_reject; - cmp A,MSG_NOOP je mesgin_done; - cmp A,MSG_IGN_WIDE_RESIDUE je mesgin_wide_residue; - -rej_mesgin: -/* - * We have no idea what this message in is, so we issue a message reject - * and hope for the best. In any case, rejection should be a rare - * occurrence - signal the driver when it happens. - */ - mvi INTSTAT,SEND_REJECT; /* let driver know */ - - mvi MSG_MESSAGE_REJECT call mk_mesg; - -mesgin_done: - mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ - jmp ITloop; - - -mesgin_complete: -/* - * We got a "command complete" message, so put the SCB_TAG into the QOUTFIFO, - * and trigger a completion interrupt. Before doing so, check to see if there - * is a residual or the status byte is something other than STATUS_GOOD (0). - * In either of these conditions, we upload the SCB back to the host so it can - * process this information. In the case of a non zero status byte, we - * additionally interrupt the kernel driver synchronously, allowing it to - * decide if sense should be retrieved. If the kernel driver wishes to request - * sense, it will fill the kernel SCB with a request sense command and set - * RETURN_1 to SEND_SENSE. If RETURN_1 is set to SEND_SENSE we redownload - * the SCB, and process it as the next command by adding it to the waiting list. - * If the kernel driver does not wish to request sense, it need only clear - * RETURN_1, and the command is allowed to complete normally. We don't bother - * to post to the QOUTFIFO in the error cases since it would require extra - * work in the kernel driver to ensure that the entry was removed before the - * command complete code tried processing it. - */ - -/* - * First check for residuals - */ - test SCB_RESID_SGCNT,0xff jnz upload_scb; - test SCB_TARGET_STATUS,0xff jz complete; /* Good Status? */ -upload_scb: - mvi DMAPARAMS, FIFORESET; - mov SCB_TAG call dma_scb; -check_status: - test SCB_TARGET_STATUS,0xff jz complete; /* Just a residual? */ - mvi INTSTAT,BAD_STATUS; /* let driver know */ - nop; - cmp RETURN_1, SEND_SENSE jne complete; - /* This SCB becomes the next to execute as it will retrieve sense */ - mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; - mov SCB_TAG call dma_scb; -add_to_waiting_list: - mov SCB_NEXT,WAITING_SCBH; - mov WAITING_SCBH, SCBPTR; - /* - * Prepare our selection hardware before the busfree so we have a - * high probability of winning arbitration. - */ - call start_selection; - jmp await_busfree; - -complete: - /* If we are untagged, clear our address up in host ram */ - test SCB_CONTROL, TAG_ENB jnz complete_post; - mov A, SAVED_TCL; - mvi UNTAGGEDSCB_OFFSET call post_byte_setup; - mvi SCB_LIST_NULL call post_byte; - -complete_post: - /* Post the SCB and issue an interrupt */ - if ((p->features & AHC_QUEUE_REGS) != 0) { - mov A, SDSCB_QOFF; - } else { - mov A, QOUTPOS; - } - mvi QOUTFIFO_OFFSET call post_byte_setup; - mov SCB_TAG call post_byte; - if ((p->features & AHC_QUEUE_REGS) == 0) { - inc QOUTPOS; - } - mvi INTSTAT,CMDCMPLT; - -add_to_free_list: - call add_scb_to_free_list; - jmp await_busfree; - -/* - * Is it an extended message? Copy the message to our message buffer and - * notify the host. The host will tell us whether to reject this message, - * respond to it with the message that the host placed in our message buffer, - * or simply to do nothing. - */ -mesgin_extended: - mvi INTSTAT,EXTENDED_MSG; /* let driver know */ - jmp ITloop; - -/* - * Is it a disconnect message? Set a flag in the SCB to remind us - * and await the bus going free. - */ -mesgin_disconnect: - or SCB_CONTROL,DISCONNECTED; - call add_scb_to_disc_list; - jmp await_busfree; - -/* - * Save data pointers message: - * Copying RAM values back to SCB, for Save Data Pointers message, but - * only if we've actually been into a data phase to change them. This - * protects against bogus data in scratch ram and the residual counts - * since they are only initialized when we go into data_in or data_out. - */ -mesgin_sdptrs: - test SEQ_FLAGS, DPHASE jz mesgin_done; - /* - * The SCB SGPTR becomes the next one we'll download, - * and the SCB DATAPTR becomes the current SHADDR. - * Use the residual number since STCNT is corrupted by - * any message transfer. - */ - if ((p->features & AHC_CMD_CHAN) != 0) { - bmov SCB_SGCOUNT, SG_COUNT, 5; - bmov SCB_DATAPTR, SHADDR, 4; - bmov SCB_DATACNT, SCB_RESID_DCNT, 3; - } else { - mvi DINDEX, SCB_SGCOUNT; - mvi SG_COUNT call bcopy_5; - mvi DINDEX, SCB_DATAPTR; - mvi SHADDR call bcopy_4; - mvi SCB_RESID_DCNT call bcopy_3; - } - jmp mesgin_done; - -/* - * Restore pointers message? Data pointers are recopied from the - * SCB anytime we enter a data phase for the first time, so all - * we need to do is clear the DPHASE flag and let the data phase - * code do the rest. - */ -mesgin_rdptrs: - and SEQ_FLAGS, ~DPHASE; /* - * We'll reload them - * the next time through - * the dataphase. - */ - jmp mesgin_done; - -/* - * Identify message? For a reconnecting target, this tells us the lun - * that the reconnection is for - find the correct SCB and switch to it, - * clearing the "disconnected" bit so we don't "find" it by accident later. - */ -mesgin_identify: - - if ((p->features & AHC_WIDE) != 0) { - and A,0x0f; /* lun in lower four bits */ - } else { - and A,0x07; /* lun in lower three bits */ - } - or SAVED_TCL,A; /* SAVED_TCL should be complete now */ - - mvi ARG_2, SCB_LIST_NULL; /* SCBID of prev SCB in disc List */ - call get_untagged_SCBID; - cmp ARG_1, SCB_LIST_NULL je snoop_tag; - if ((p->flags & AHC_PAGESCBS) != 0) { - test SEQ_FLAGS, SCBPTR_VALID jz use_retrieveSCB; - } - /* - * If the SCB was found in the disconnected list (as is - * always the case in non-paging scenarios), SCBPTR is already - * set to the correct SCB. So, simply setup the SCB and get - * on with things. - */ - mov SCBPTR call rem_scb_from_disc_list; - jmp setup_SCB; -/* - * Here we "snoop" the bus looking for a SIMPLE QUEUE TAG message. - * If we get one, we use the tag returned to find the proper - * SCB. With SCB paging, this requires using search for both tagged - * and non-tagged transactions since the SCB may exist in any slot. - * If we're not using SCB paging, we can use the tag as the direct - * index to the SCB. - */ -snoop_tag: - mov NONE,SCSIDATL; /* ACK Identify MSG */ -snoop_tag_loop: - call phase_lock; - cmp LASTPHASE, P_MESGIN jne not_found; - cmp SCSIBUSL,MSG_SIMPLE_Q_TAG jne not_found; -get_tag: - mvi ARG_1 call inb_next; /* tag value */ - -use_retrieveSCB: - call retrieveSCB; -setup_SCB: - mov A, SAVED_TCL; - cmp SCB_TCL, A jne not_found_cleanup_scb; - test SCB_CONTROL,DISCONNECTED jz not_found_cleanup_scb; - and SCB_CONTROL,~DISCONNECTED; - or SEQ_FLAGS,IDENTIFY_SEEN; /* make note of IDENTIFY */ - /* See if the host wants to send a message upon reconnection */ - test SCB_CONTROL, MK_MESSAGE jz mesgin_done; - and SCB_CONTROL, ~MK_MESSAGE; - mvi HOST_MSG call mk_mesg; - jmp mesgin_done; - -not_found_cleanup_scb: - test SCB_CONTROL, DISCONNECTED jz . + 3; - call add_scb_to_disc_list; - jmp not_found; - call add_scb_to_free_list; -not_found: - mvi INTSTAT, NO_MATCH; - mvi MSG_BUS_DEV_RESET call mk_mesg; - jmp mesgin_done; - -/* - * Message reject? Let the kernel driver handle this. If we have an - * outstanding WDTR or SDTR negotiation, assume that it's a response from - * the target selecting 8bit or asynchronous transfer, otherwise just ignore - * it since we have no clue what it pertains to. - */ -mesgin_reject: - mvi INTSTAT, REJECT_MSG; - jmp mesgin_done; - -/* - * Wide Residue. We handle the simple cases, but pass of the one hard case - * to the kernel (when the residue byte happened to cause us to advance our - * sg element array, so we know have to back that advance out). - */ -mesgin_wide_residue: - mvi ARG_1 call inb_next; /* ACK the wide_residue and get */ - /* the size byte */ -/* - * In order for this to be reliable, we have to do all sorts of horrible - * magic in terms of resetting the datafifo and reloading the shadow layer - * with the correct new values (so that a subsequent save data pointers - * message will do the right thing). We let the kernel do that work. - */ - mvi INTSTAT, WIDE_RESIDUE; - jmp mesgin_done; - -/* - * [ ADD MORE MESSAGE HANDLING HERE ] - */ - -/* - * Locking the driver out, build a one-byte message passed in SINDEX - * if there is no active message already. SINDEX is returned intact. - */ -mk_mesg: - or SCSISIGO,ATNO,LASTPHASE;/* turn on ATNO */ - mov MSG_OUT,SINDEX ret; - -/* - * Functions to read data in Automatic PIO mode. - * - * According to Adaptec's documentation, an ACK is not sent on input from - * the target until SCSIDATL is read from. So we wait until SCSIDATL is - * latched (the usual way), then read the data byte directly off the bus - * using SCSIBUSL. When we have pulled the ATN line, or we just want to - * acknowledge the byte, then we do a dummy read from SCISDATL. The SCSI - * spec guarantees that the target will hold the data byte on the bus until - * we send our ACK. - * - * The assumption here is that these are called in a particular sequence, - * and that REQ is already set when inb_first is called. inb_{first,next} - * use the same calling convention as inb. - */ - -inb_next: - mov NONE,SCSIDATL; /*dummy read from latch to ACK*/ -inb_next_wait: - /* - * If there is a parity error, wait for the kernel to - * see the interrupt and prepare our message response - * before continuing. - */ - test SSTAT1, REQINIT jz inb_next_wait; - test SSTAT1, SCSIPERR jnz .; - and LASTPHASE, PHASE_MASK, SCSISIGI; - cmp LASTPHASE, P_MESGIN jne mesgin_phasemis; -inb_first: - mov DINDEX,SINDEX; - mov DINDIR,SCSIBUSL ret; /*read byte directly from bus*/ -inb_last: - mov NONE,SCSIDATL ret; /*dummy read from latch to ACK*/ - - -mesgin_phasemis: -/* - * We expected to receive another byte, but the target changed phase - */ - mvi INTSTAT, MSGIN_PHASEMIS; - jmp ITloop; - -/* - * DMA data transfer. HADDR and HCNT must be loaded first, and - * SINDEX should contain the value to load DFCNTRL with - 0x3d for - * host->scsi, or 0x39 for scsi->host. The SCSI channel is cleared - * during initialization. - */ -if ((p->features & AHC_ULTRA2) == 0) { -dma: - mov DFCNTRL,SINDEX; -dma_loop: - test SSTAT0,DMADONE jnz dma_dmadone; - test SSTAT1,PHASEMIS jz dma_loop; /* ie. underrun */ -dma_phasemis: - test SSTAT0,SDONE jnz dma_checkfifo; - mov SINDEX,ALLZEROS; /* Notify caller of phasemiss */ - -/* - * We will be "done" DMAing when the transfer count goes to zero, or - * the target changes the phase (in light of this, it makes sense that - * the DMA circuitry doesn't ACK when PHASEMIS is active). If we are - * doing a SCSI->Host transfer, the data FIFO should be flushed auto- - * magically on STCNT=0 or a phase change, so just wait for FIFO empty - * status. - */ -dma_checkfifo: - test DFCNTRL,DIRECTION jnz dma_fifoempty; -dma_fifoflush: - test DFSTATUS,FIFOEMP jz dma_fifoflush; - -dma_fifoempty: - /* Don't clobber an inprogress host data transfer */ - test DFSTATUS, MREQPEND jnz dma_fifoempty; -/* - * Now shut the DMA enables off and make sure that the DMA enables are - * actually off first lest we get an ILLSADDR. - */ -dma_dmadone: - cmp LASTPHASE, P_COMMAND je dma_await_nreq; - test SCSIRATE, 0x0f jnz dma_shutdown; -dma_await_nreq: - test SCSISIGI, REQI jz dma_shutdown; - test SSTAT1, (PHASEMIS|REQINIT) jz dma_await_nreq; -dma_shutdown: - and DFCNTRL, ~(SCSIEN|SDMAEN|HDMAEN); -dma_halt: - /* - * Some revisions of the aic7880 have a problem where, if the - * data fifo is full, but the PCI input latch is not empty, - * HDMAEN cannot be cleared. The fix used here is to attempt - * to drain the data fifo until there is space for the input - * latch to drain and HDMAEN de-asserts. - */ - if ((p->bugs & AHC_BUG_PCI_2_1_RETRY) != 0) { - mov NONE, DFDAT; - } - test DFCNTRL, (SCSIEN|SDMAEN|HDMAEN) jnz dma_halt; -} -return: - ret; - -/* - * Assert that if we've been reselected, then we've seen an IDENTIFY - * message. - */ -assert: - test SEQ_FLAGS,IDENTIFY_SEEN jnz return; /* seen IDENTIFY? */ - - mvi INTSTAT,NO_IDENT ret; /* no - tell the kernel */ - -/* - * Locate a disconnected SCB either by SAVED_TCL (ARG_1 is SCB_LIST_NULL) - * or by the SCBID ARG_1. The search begins at the SCB index passed in - * via SINDEX which is an SCB that must be on the disconnected list. If - * the SCB cannot be found, SINDEX will be SCB_LIST_NULL, otherwise, SCBPTR - * is set to the proper SCB. - */ -findSCB: - mov SCBPTR,SINDEX; /* Initialize SCBPTR */ - cmp ARG_1, SCB_LIST_NULL jne findSCB_by_SCBID; - mov A, SAVED_TCL; - mvi SCB_TCL jmp findSCB_loop; /* &SCB_TCL -> SINDEX */ -findSCB_by_SCBID: - mov A, ARG_1; /* Tag passed in ARG_1 */ - mvi SCB_TAG jmp findSCB_loop; /* &SCB_TAG -> SINDEX */ -findSCB_next: - mov ARG_2, SCBPTR; - cmp SCB_NEXT, SCB_LIST_NULL je notFound; - mov SCBPTR,SCB_NEXT; - dec SINDEX; /* Last comparison moved us too far */ -findSCB_loop: - cmp SINDIR, A jne findSCB_next; - mov SINDEX, SCBPTR ret; -notFound: - mvi SINDEX, SCB_LIST_NULL ret; - -/* - * Retrieve an SCB by SCBID first searching the disconnected list falling - * back to DMA'ing the SCB down from the host. This routine assumes that - * ARG_1 is the SCBID of interest and that SINDEX is the position in the - * disconnected list to start the search from. If SINDEX is SCB_LIST_NULL, - * we go directly to the host for the SCB. - */ -retrieveSCB: - test SEQ_FLAGS, SCBPTR_VALID jz retrieve_from_host; - mov SCBPTR call findSCB; /* Continue the search */ - cmp SINDEX, SCB_LIST_NULL je retrieve_from_host; - -/* - * This routine expects SINDEX to contain the index of the SCB to be - * removed, SCBPTR to be pointing to that SCB, and ARG_2 to be the - * SCBID of the SCB just previous to this one in the list or SCB_LIST_NULL - * if it is at the head. - */ -rem_scb_from_disc_list: -/* Remove this SCB from the disconnection list */ - cmp ARG_2, SCB_LIST_NULL je rHead; - mov DINDEX, SCB_NEXT; - mov SCBPTR, ARG_2; - mov SCB_NEXT, DINDEX; - mov SCBPTR, SINDEX ret; -rHead: - mov DISCONNECTED_SCBH,SCB_NEXT ret; - -retrieve_from_host: -/* - * We didn't find it. Pull an SCB and DMA down the one we want. - * We should never get here in the non-paging case. - */ - mov ALLZEROS call get_free_or_disc_scb; - mvi DMAPARAMS, HDMAEN|DIRECTION|FIFORESET; - /* Jump instead of call as we want to return anyway */ - mov ARG_1 jmp dma_scb; - -/* - * Determine whether a target is using tagged or non-tagged transactions - * by first looking for a matching transaction based on the TCL and if - * that fails, looking up this device in the host's untagged SCB array. - * The TCL to search for is assumed to be in SAVED_TCL. The value is - * returned in ARG_1 (SCB_LIST_NULL for tagged, SCBID for non-tagged). - * The SCBPTR_VALID bit is set in SEQ_FLAGS if we found the information - * in an SCB instead of having to go to the host. - */ -get_untagged_SCBID: - cmp DISCONNECTED_SCBH, SCB_LIST_NULL je get_SCBID_from_host; - mvi ARG_1, SCB_LIST_NULL; - mov DISCONNECTED_SCBH call findSCB; - cmp SINDEX, SCB_LIST_NULL je get_SCBID_from_host; - or SEQ_FLAGS, SCBPTR_VALID;/* Was in disconnected list */ - test SCB_CONTROL, TAG_ENB jnz . + 2; - mov ARG_1, SCB_TAG ret; - mvi ARG_1, SCB_LIST_NULL ret; - -/* - * Fetch a byte from host memory given an index of (A + (256 * SINDEX)) - * and a base address of SCBID_ADDR. The byte is returned in RETURN_2. - */ -fetch_byte: - mov ARG_2, SINDEX; - if ((p->features & AHC_CMD_CHAN) != 0) { - mvi DINDEX, CCHADDR; - mvi SCBID_ADDR call set_1byte_addr; - mvi CCHCNT, 1; - mvi CCSGCTL, CCSGEN|CCSGRESET; - test CCSGCTL, CCSGDONE jz .; - mvi CCSGCTL, CCSGRESET; - bmov RETURN_2, CCSGRAM, 1 ret; - } else { - mvi DINDEX, HADDR; - mvi SCBID_ADDR call set_1byte_addr; - mvi HCNT[0], 1; - clr HCNT[1]; - clr HCNT[2]; - mvi DFCNTRL, HDMAEN|DIRECTION|FIFORESET; - call dma_finish; - mov RETURN_2, DFDAT ret; - } - -/* - * Prepare the hardware to post a byte to host memory given an - * index of (A + (256 * SINDEX)) and a base address of SCBID_ADDR. - */ -post_byte_setup: - mov ARG_2, SINDEX; - if ((p->features & AHC_CMD_CHAN) != 0) { - mvi DINDEX, CCHADDR; - mvi SCBID_ADDR call set_1byte_addr; - mvi CCHCNT, 1; - mvi CCSCBCTL, CCSCBRESET ret; - } else { - mvi DINDEX, HADDR; - mvi SCBID_ADDR call set_1byte_addr; - mvi HCNT[0], 1; - clr HCNT[1]; - clr HCNT[2]; - mvi DFCNTRL, FIFORESET ret; - } - -post_byte: - if ((p->features & AHC_CMD_CHAN) != 0) { - bmov CCSCBRAM, SINDEX, 1; - or CCSCBCTL, CCSCBEN|CCSCBRESET; - test CCSCBCTL, CCSCBDONE jz .; - clr CCSCBCTL ret; - } else { - mov DFDAT, SINDEX; - or DFCNTRL, HDMAEN|FIFOFLUSH; - jmp dma_finish; - } - -get_SCBID_from_host: - mov A, SAVED_TCL; - mvi UNTAGGEDSCB_OFFSET call fetch_byte; - mov RETURN_1, RETURN_2 ret; - -phase_lock: - test SSTAT1, REQINIT jz phase_lock; - test SSTAT1, SCSIPERR jnz phase_lock; - and SCSISIGO, PHASE_MASK, SCSISIGI; - and LASTPHASE, PHASE_MASK, SCSISIGI ret; - -if ((p->features & AHC_CMD_CHAN) == 0) { -set_stcnt_from_hcnt: - mov STCNT[0], HCNT[0]; - mov STCNT[1], HCNT[1]; - mov STCNT[2], HCNT[2] ret; - -bcopy_7: - mov DINDIR, SINDIR; - mov DINDIR, SINDIR; -bcopy_5: - mov DINDIR, SINDIR; -bcopy_4: - mov DINDIR, SINDIR; -bcopy_3: - mov DINDIR, SINDIR; - mov DINDIR, SINDIR; - mov DINDIR, SINDIR ret; -} - -/* - * Setup addr assuming that A is an index into - * an array of 32byte objects, SINDEX contains - * the base address of that array, and DINDEX - * contains the base address of the location - * to store the indexed address. - */ -set_32byte_addr: - shr ARG_2, 3, A; - shl A, 5; -/* - * Setup addr assuming that A + (ARG_1 * 256) is an - * index into an array of 1byte objects, SINDEX contains - * the base address of that array, and DINDEX contains - * the base address of the location to store the computed - * address. - */ -set_1byte_addr: - add DINDIR, A, SINDIR; - mov A, ARG_2; - adc DINDIR, A, SINDIR; - clr A; - adc DINDIR, A, SINDIR; - adc DINDIR, A, SINDIR ret; - -/* - * Either post or fetch and SCB from host memory based on the - * DIRECTION bit in DMAPARAMS. The host SCB index is in SINDEX. - */ -dma_scb: - mov A, SINDEX; - if ((p->features & AHC_CMD_CHAN) != 0) { - mvi DINDEX, CCHADDR; - mvi HSCB_ADDR call set_32byte_addr; - mov CCSCBPTR, SCBPTR; - mvi CCHCNT, 32; - test DMAPARAMS, DIRECTION jz dma_scb_tohost; - mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBDIR|CCSCBRESET; - cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN|CCSCBDIR jne .; - jmp dma_scb_finish; -dma_scb_tohost: - if ((p->features & AHC_ULTRA2) == 0) { - mvi CCSCBCTL, CCSCBRESET; - bmov CCSCBRAM, SCB_CONTROL, 32; - or CCSCBCTL, CCSCBEN|CCSCBRESET; - test CCSCBCTL, CCSCBDONE jz .; - } - if ((p->features & AHC_ULTRA2) != 0) { - if ((p->bugs & AHC_BUG_SCBCHAN_UPLOAD) != 0) { - mvi CCSCBCTL, CCARREN|CCSCBRESET; - cmp CCSCBCTL, ARRDONE|CCARREN jne .; - mvi CCHCNT, 32; - mvi CCSCBCTL, CCSCBEN|CCSCBRESET; - cmp CCSCBCTL, CCSCBDONE|CCSCBEN jne .; - } else { - mvi CCSCBCTL, CCARREN|CCSCBEN|CCSCBRESET; - cmp CCSCBCTL, CCSCBDONE|ARRDONE|CCARREN|CCSCBEN jne .; - } - } -dma_scb_finish: - clr CCSCBCTL; - test CCSCBCTL, CCARREN|CCSCBEN jnz .; - ret; - } - if ((p->features & AHC_CMD_CHAN) == 0) { - mvi DINDEX, HADDR; - mvi HSCB_ADDR call set_32byte_addr; - mvi HCNT[0], 32; - clr HCNT[1]; - clr HCNT[2]; - mov DFCNTRL, DMAPARAMS; - test DMAPARAMS, DIRECTION jnz dma_scb_fromhost; - /* Fill it with the SCB data */ -copy_scb_tofifo: - mvi SINDEX, SCB_CONTROL; - add A, 32, SINDEX; -copy_scb_tofifo_loop: - mov DFDAT,SINDIR; - mov DFDAT,SINDIR; - mov DFDAT,SINDIR; - mov DFDAT,SINDIR; - mov DFDAT,SINDIR; - mov DFDAT,SINDIR; - mov DFDAT,SINDIR; - mov DFDAT,SINDIR; - cmp SINDEX, A jne copy_scb_tofifo_loop; - or DFCNTRL, HDMAEN|FIFOFLUSH; - jmp dma_finish; -dma_scb_fromhost: - mvi DINDEX, SCB_CONTROL; - if ((p->bugs & AHC_BUG_PCI_2_1_RETRY) != 0) { - /* - * Set the A to -24. It it hits 0, then we let - * our code fall through to dfdat_in_8 to complete - * the last of the copy. - * - * Also, things happen 8 bytes at a time in this - * case, so we may need to drain the fifo at most - * 3 times to keep things flowing - */ - mvi A, -24; -dma_scb_hang_fifo: - /* Wait for the first bit of data to hit the fifo */ - test DFSTATUS, FIFOEMP jnz .; -dma_scb_hang_wait: - /* OK, now they've started to transfer into the fifo, - * so wait for them to stop trying to transfer any - * more data. - */ - test DFSTATUS, MREQPEND jnz .; - /* - * OK, they started, then they stopped, now see if they - * managed to complete the job before stopping. Try - * it multiple times to give the chip a few cycles to - * set the flag if it did complete. - */ - test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; - test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; - test DFSTATUS, HDONE jnz dma_scb_hang_dma_done; - /* - * Too bad, the chip didn't complete the DMA, but there - * aren't any more memory requests pending, so that - * means it stopped part way through and hung. That's - * our bug, so now we drain what data there is in the - * fifo in order to get things going again. - */ -dma_scb_hang_empty_fifo: - call dfdat_in_8; - add A, 8; - add SINDEX, A, HCNT; - /* - * If there are another 8 bytes of data waiting in the - * fifo, then the carry bit will be set as a result - * of the above add command (unless A is non-negative, - * in which case the carry bit won't be set). - */ - jc dma_scb_hang_empty_fifo; - /* - * We've emptied the fifo now, but we wouldn't have got - * here if the memory transfer hadn't stopped part way - * through, so go back up to the beginning of the - * loop and start over. When it succeeds in getting - * all the data down, HDONE will be set and we'll - * jump to the code just below here. - */ - jmp dma_scb_hang_fifo; -dma_scb_hang_dma_done: - and DFCNTRL, ~HDMAEN; - test DFCNTRL, HDMAEN jnz .; - call dfdat_in_8; - add A, 8; - cmp A, 8 jne . - 2; - ret; - } else { - call dma_finish; - call dfdat_in_8; - call dfdat_in_8; - call dfdat_in_8; - } -dfdat_in_8: - mov DINDIR,DFDAT; -dfdat_in_7: - mov DINDIR,DFDAT; - mov DINDIR,DFDAT; - mov DINDIR,DFDAT; - mov DINDIR,DFDAT; - mov DINDIR,DFDAT; - mov DINDIR,DFDAT; - mov DINDIR,DFDAT ret; - } - - -/* - * Wait for DMA from host memory to data FIFO to complete, then disable - * DMA and wait for it to acknowledge that it's off. - */ -if ((p->features & AHC_CMD_CHAN) == 0) { -dma_finish: - test DFSTATUS,HDONE jz dma_finish; - /* Turn off DMA */ - and DFCNTRL, ~HDMAEN; - test DFCNTRL, HDMAEN jnz .; - ret; -} - -add_scb_to_free_list: - if ((p->flags & AHC_PAGESCBS) != 0) { - mov SCB_NEXT, FREE_SCBH; - mov FREE_SCBH, SCBPTR; - } - mvi SCB_TAG, SCB_LIST_NULL ret; - -if ((p->flags & AHC_PAGESCBS) != 0) { -get_free_or_disc_scb: - cmp FREE_SCBH, SCB_LIST_NULL jne dequeue_free_scb; - cmp DISCONNECTED_SCBH, SCB_LIST_NULL jne dequeue_disc_scb; -return_error: - mvi SINDEX, SCB_LIST_NULL ret; -dequeue_disc_scb: - mov SCBPTR, DISCONNECTED_SCBH; -dma_up_scb: - mvi DMAPARAMS, FIFORESET; - mov SCB_TAG call dma_scb; -unlink_disc_scb: - mov DISCONNECTED_SCBH, SCB_NEXT ret; -dequeue_free_scb: - mov SCBPTR, FREE_SCBH; - mov FREE_SCBH, SCB_NEXT ret; -} - -add_scb_to_disc_list: -/* - * Link this SCB into the DISCONNECTED list. This list holds the - * candidates for paging out an SCB if one is needed for a new command. - * Modifying the disconnected list is a critical(pause dissabled) section. - */ - mov SCB_NEXT, DISCONNECTED_SCBH; - mov DISCONNECTED_SCBH, SCBPTR ret; diff --git a/drivers/scsi/aic7xxx_old/aic7xxx_proc.c b/drivers/scsi/aic7xxx_old/aic7xxx_proc.c deleted file mode 100644 index 976f45ccf2c..00000000000 --- a/drivers/scsi/aic7xxx_old/aic7xxx_proc.c +++ /dev/null @@ -1,270 +0,0 @@ -/*+M************************************************************************* - * Adaptec AIC7xxx device driver proc support for Linux. - * - * Copyright (c) 1995, 1996 Dean W. Gehnert - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2, or (at your option) - * any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; see the file COPYING. If not, write to - * the Free Software Foundation, 675 Mass Ave, Cambridge, MA 02139, USA. - * - * ---------------------------------------------------------------- - * o Modified from the EATA-DMA /proc support. - * o Additional support for device block statistics provided by - * Matthew Jacob. - * o Correction of overflow by Heinz Mauelshagen - * o Adittional corrections by Doug Ledford - * - * Dean W. Gehnert, deang@teleport.com, 05/01/96 - * - * $Id: aic7xxx_proc.c,v 4.1 1997/06/97 08:23:42 deang Exp $ - *-M*************************************************************************/ - - -#define HDRB \ -" 0 - 4K 4 - 16K 16 - 64K 64 - 256K 256K - 1M 1M+" - - -/*+F************************************************************************* - * Function: - * aic7xxx_show_info - * - * Description: - * Return information to handle /proc support for the driver. - *-F*************************************************************************/ -int -aic7xxx_show_info(struct seq_file *m, struct Scsi_Host *HBAptr) -{ - struct aic7xxx_host *p; - struct aic_dev_data *aic_dev; - struct scsi_device *sdptr; - unsigned char i; - unsigned char tindex; - - for(p=first_aic7xxx; p && p->host != HBAptr; p=p->next) - ; - - if (!p) - { - seq_printf(m, "Can't find adapter for host number %d\n", HBAptr->host_no); - return 0; - } - - p = (struct aic7xxx_host *) HBAptr->hostdata; - - seq_printf(m, "Adaptec AIC7xxx driver version: "); - seq_printf(m, "%s/", AIC7XXX_C_VERSION); - seq_printf(m, "%s", AIC7XXX_H_VERSION); - seq_printf(m, "\n"); - seq_printf(m, "Adapter Configuration:\n"); - seq_printf(m, " SCSI Adapter: %s\n", - board_names[p->board_name_index]); - if (p->flags & AHC_TWIN) - seq_printf(m, " Twin Channel Controller "); - else - { - char *channel = ""; - char *ultra = ""; - char *wide = "Narrow "; - if (p->flags & AHC_MULTI_CHANNEL) - { - channel = " Channel A"; - if (p->flags & (AHC_CHNLB|AHC_CHNLC)) - channel = (p->flags & AHC_CHNLB) ? " Channel B" : " Channel C"; - } - if (p->features & AHC_WIDE) - wide = "Wide "; - if (p->features & AHC_ULTRA3) - { - switch(p->chip & AHC_CHIPID_MASK) - { - case AHC_AIC7892: - case AHC_AIC7899: - ultra = "Ultra-160/m LVD/SE "; - break; - default: - ultra = "Ultra-3 LVD/SE "; - break; - } - } - else if (p->features & AHC_ULTRA2) - ultra = "Ultra-2 LVD/SE "; - else if (p->features & AHC_ULTRA) - ultra = "Ultra "; - seq_printf(m, " %s%sController%s ", - ultra, wide, channel); - } - switch(p->chip & ~AHC_CHIPID_MASK) - { - case AHC_VL: - seq_printf(m, "at VLB slot %d\n", p->pci_device_fn); - break; - case AHC_EISA: - seq_printf(m, "at EISA slot %d\n", p->pci_device_fn); - break; - default: - seq_printf(m, "at PCI %d/%d/%d\n", p->pci_bus, - PCI_SLOT(p->pci_device_fn), PCI_FUNC(p->pci_device_fn)); - break; - } - if( !(p->maddr) ) - { - seq_printf(m, " Programmed I/O Base: %lx\n", p->base); - } - else - { - seq_printf(m, " PCI MMAPed I/O Base: 0x%lx\n", p->mbase); - } - if( (p->chip & (AHC_VL | AHC_EISA)) ) - { - seq_printf(m, " BIOS Memory Address: 0x%08x\n", p->bios_address); - } - seq_printf(m, " Adapter SEEPROM Config: %s\n", - (p->flags & AHC_SEEPROM_FOUND) ? "SEEPROM found and used." : - ((p->flags & AHC_USEDEFAULTS) ? "SEEPROM not found, using defaults." : - "SEEPROM not found, using leftover BIOS values.") ); - seq_printf(m, " Adaptec SCSI BIOS: %s\n", - (p->flags & AHC_BIOS_ENABLED) ? "Enabled" : "Disabled"); - seq_printf(m, " IRQ: %d\n", HBAptr->irq); - seq_printf(m, " SCBs: Active %d, Max Active %d,\n", - p->activescbs, p->max_activescbs); - seq_printf(m, " Allocated %d, HW %d, " - "Page %d\n", p->scb_data->numscbs, p->scb_data->maxhscbs, - p->scb_data->maxscbs); - if (p->flags & AHC_EXTERNAL_SRAM) - seq_printf(m, " Using External SCB SRAM\n"); - seq_printf(m, " Interrupts: %ld", p->isr_count); - if (p->chip & AHC_EISA) - { - seq_printf(m, " %s\n", - (p->pause & IRQMS) ? "(Level Sensitive)" : "(Edge Triggered)"); - } - else - { - seq_printf(m, "\n"); - } - seq_printf(m, " BIOS Control Word: 0x%04x\n", - p->bios_control); - seq_printf(m, " Adapter Control Word: 0x%04x\n", - p->adapter_control); - seq_printf(m, " Extended Translation: %sabled\n", - (p->flags & AHC_EXTEND_TRANS_A) ? "En" : "Dis"); - seq_printf(m, "Disconnect Enable Flags: 0x%04x\n", p->discenable); - if (p->features & (AHC_ULTRA | AHC_ULTRA2)) - { - seq_printf(m, " Ultra Enable Flags: 0x%04x\n", p->ultraenb); - } - seq_printf(m, "Default Tag Queue Depth: %d\n", aic7xxx_default_queue_depth); - seq_printf(m, " Tagged Queue By Device array for aic7xxx host " - "instance %d:\n", p->instance); - seq_printf(m, " {"); - for(i=0; i < (MAX_TARGETS - 1); i++) - seq_printf(m, "%d,",aic7xxx_tag_info[p->instance].tag_commands[i]); - seq_printf(m, "%d}\n",aic7xxx_tag_info[p->instance].tag_commands[i]); - - seq_printf(m, "\n"); - seq_printf(m, "Statistics:\n\n"); - list_for_each_entry(aic_dev, &p->aic_devs, list) - { - sdptr = aic_dev->SDptr; - tindex = sdptr->channel << 3 | sdptr->id; - seq_printf(m, "(scsi%d:%d:%d:%d)\n", - p->host_no, sdptr->channel, sdptr->id, sdptr->lun); - seq_printf(m, " Device using %s/%s", - (aic_dev->cur.width == MSG_EXT_WDTR_BUS_16_BIT) ? - "Wide" : "Narrow", - (aic_dev->cur.offset != 0) ? - "Sync transfers at " : "Async transfers.\n" ); - if (aic_dev->cur.offset != 0) - { - struct aic7xxx_syncrate *sync_rate; - unsigned char options = aic_dev->cur.options; - int period = aic_dev->cur.period; - int rate = (aic_dev->cur.width == - MSG_EXT_WDTR_BUS_16_BIT) ? 1 : 0; - - sync_rate = aic7xxx_find_syncrate(p, &period, 0, &options); - if (sync_rate != NULL) - { - seq_printf(m, "%s MByte/sec, offset %d\n", - sync_rate->rate[rate], - aic_dev->cur.offset ); - } - else - { - seq_printf(m, "3.3 MByte/sec, offset %d\n", - aic_dev->cur.offset ); - } - } - seq_printf(m, " Transinfo settings: "); - seq_printf(m, "current(%d/%d/%d/%d), ", - aic_dev->cur.period, - aic_dev->cur.offset, - aic_dev->cur.width, - aic_dev->cur.options); - seq_printf(m, "goal(%d/%d/%d/%d), ", - aic_dev->goal.period, - aic_dev->goal.offset, - aic_dev->goal.width, - aic_dev->goal.options); - seq_printf(m, "user(%d/%d/%d/%d)\n", - p->user[tindex].period, - p->user[tindex].offset, - p->user[tindex].width, - p->user[tindex].options); - if(sdptr->simple_tags) - { - seq_printf(m, " Tagged Command Queueing Enabled, Ordered Tags %s, Depth %d/%d\n", sdptr->ordered_tags ? "Enabled" : "Disabled", sdptr->queue_depth, aic_dev->max_q_depth); - } - if(aic_dev->barrier_total) - seq_printf(m, " Total transfers %ld:\n (%ld/%ld/%ld/%ld reads/writes/REQ_BARRIER/Ordered Tags)\n", - aic_dev->r_total+aic_dev->w_total, aic_dev->r_total, aic_dev->w_total, - aic_dev->barrier_total, aic_dev->ordered_total); - else - seq_printf(m, " Total transfers %ld:\n (%ld/%ld reads/writes)\n", - aic_dev->r_total+aic_dev->w_total, aic_dev->r_total, aic_dev->w_total); - seq_printf(m, "%s\n", HDRB); - seq_printf(m, " Reads:"); - for (i = 0; i < ARRAY_SIZE(aic_dev->r_bins); i++) - { - seq_printf(m, " %10ld", aic_dev->r_bins[i]); - } - seq_printf(m, "\n"); - seq_printf(m, " Writes:"); - for (i = 0; i < ARRAY_SIZE(aic_dev->w_bins); i++) - { - seq_printf(m, " %10ld", aic_dev->w_bins[i]); - } - seq_printf(m, "\n"); - seq_printf(m, "\n\n"); - } - return 0; -} - -/* - * Overrides for Emacs so that we follow Linus's tabbing style. - * Emacs will notice this stuff at the end of the file and automatically - * adjust the settings for this buffer only. This must remain at the end - * of the file. - * --------------------------------------------------------------------------- - * Local variables: - * c-indent-level: 2 - * c-brace-imaginary-offset: 0 - * c-brace-offset: -2 - * c-argdecl-indent: 2 - * c-label-offset: -2 - * c-continued-statement-offset: 2 - * c-continued-brace-offset: 0 - * indent-tabs-mode: nil - * tab-width: 8 - * End: - */ diff --git a/drivers/scsi/aic7xxx_old/aic7xxx_reg.h b/drivers/scsi/aic7xxx_old/aic7xxx_reg.h deleted file mode 100644 index 27f2334abc7..00000000000 --- a/drivers/scsi/aic7xxx_old/aic7xxx_reg.h +++ /dev/null @@ -1,629 +0,0 @@ -/* - * DO NOT EDIT - This file is automatically generated. - */ - -#define SCSISEQ 0x00 -#define TEMODE 0x80 -#define ENSELO 0x40 -#define ENSELI 0x20 -#define ENRSELI 0x10 -#define ENAUTOATNO 0x08 -#define ENAUTOATNI 0x04 -#define ENAUTOATNP 0x02 -#define SCSIRSTO 0x01 - -#define SXFRCTL0 0x01 -#define DFON 0x80 -#define DFPEXP 0x40 -#define FAST20 0x20 -#define CLRSTCNT 0x10 -#define SPIOEN 0x08 -#define SCAMEN 0x04 -#define CLRCHN 0x02 - -#define SXFRCTL1 0x02 -#define BITBUCKET 0x80 -#define SWRAPEN 0x40 -#define ENSPCHK 0x20 -#define STIMESEL 0x18 -#define ENSTIMER 0x04 -#define ACTNEGEN 0x02 -#define STPWEN 0x01 - -#define SCSISIGO 0x03 -#define CDO 0x80 -#define IOO 0x40 -#define MSGO 0x20 -#define ATNO 0x10 -#define SELO 0x08 -#define BSYO 0x04 -#define REQO 0x02 -#define ACKO 0x01 - -#define SCSISIGI 0x03 -#define ATNI 0x10 -#define SELI 0x08 -#define BSYI 0x04 -#define REQI 0x02 -#define ACKI 0x01 - -#define SCSIRATE 0x04 -#define WIDEXFER 0x80 -#define SXFR_ULTRA2 0x7f -#define SXFR 0x70 -#define SOFS 0x0f - -#define SCSIID 0x05 -#define SCSIOFFSET 0x05 -#define SOFS_ULTRA2 0x7f - -#define SCSIDATL 0x06 - -#define SCSIDATH 0x07 - -#define STCNT 0x08 - -#define OPTIONMODE 0x08 -#define AUTORATEEN 0x80 -#define AUTOACKEN 0x40 -#define ATNMGMNTEN 0x20 -#define BUSFREEREV 0x10 -#define EXPPHASEDIS 0x08 -#define SCSIDATL_IMGEN 0x04 -#define AUTO_MSGOUT_DE 0x02 -#define DIS_MSGIN_DUALEDGE 0x01 - -#define CLRSINT0 0x0b -#define CLRSELDO 0x40 -#define CLRSELDI 0x20 -#define CLRSELINGO 0x10 -#define CLRSWRAP 0x08 -#define CLRSPIORDY 0x02 - -#define SSTAT0 0x0b -#define TARGET 0x80 -#define SELDO 0x40 -#define SELDI 0x20 -#define SELINGO 0x10 -#define IOERR 0x08 -#define SWRAP 0x08 -#define SDONE 0x04 -#define SPIORDY 0x02 -#define DMADONE 0x01 - -#define CLRSINT1 0x0c -#define CLRSELTIMEO 0x80 -#define CLRATNO 0x40 -#define CLRSCSIRSTI 0x20 -#define CLRBUSFREE 0x08 -#define CLRSCSIPERR 0x04 -#define CLRPHASECHG 0x02 -#define CLRREQINIT 0x01 - -#define SSTAT1 0x0c -#define SELTO 0x80 -#define ATNTARG 0x40 -#define SCSIRSTI 0x20 -#define PHASEMIS 0x10 -#define BUSFREE 0x08 -#define SCSIPERR 0x04 -#define PHASECHG 0x02 -#define REQINIT 0x01 - -#define SSTAT2 0x0d -#define OVERRUN 0x80 -#define SHVALID 0x40 -#define WIDE_RES 0x20 -#define SFCNT 0x1f -#define EXP_ACTIVE 0x10 -#define CRCVALERR 0x08 -#define CRCENDERR 0x04 -#define CRCREQERR 0x02 -#define DUAL_EDGE_ERROR 0x01 - -#define SSTAT3 0x0e -#define SCSICNT 0xf0 -#define OFFCNT 0x0f - -#define SCSIID_ULTRA2 0x0f -#define OID 0x0f - -#define SIMODE0 0x10 -#define ENSELDO 0x40 -#define ENSELDI 0x20 -#define ENSELINGO 0x10 -#define ENIOERR 0x08 -#define ENSWRAP 0x08 -#define ENSDONE 0x04 -#define ENSPIORDY 0x02 -#define ENDMADONE 0x01 - -#define SIMODE1 0x11 -#define ENSELTIMO 0x80 -#define ENATNTARG 0x40 -#define ENSCSIRST 0x20 -#define ENPHASEMIS 0x10 -#define ENBUSFREE 0x08 -#define ENSCSIPERR 0x04 -#define ENPHASECHG 0x02 -#define ENREQINIT 0x01 - -#define SCSIBUSL 0x12 - -#define SCSIBUSH 0x13 - -#define SHADDR 0x14 - -#define SELTIMER 0x18 -#define STAGE6 0x20 -#define STAGE5 0x10 -#define STAGE4 0x08 -#define STAGE3 0x04 -#define STAGE2 0x02 -#define STAGE1 0x01 - -#define SELID 0x19 -#define SELID_MASK 0xf0 -#define ONEBIT 0x08 - -#define SPIOCAP 0x1b -#define SOFT1 0x80 -#define SOFT0 0x40 -#define SOFTCMDEN 0x20 -#define HAS_BRDCTL 0x10 -#define SEEPROM 0x08 -#define EEPROM 0x04 -#define ROM 0x02 -#define SSPIOCPS 0x01 - -#define BRDCTL 0x1d -#define BRDDAT7 0x80 -#define BRDDAT6 0x40 -#define BRDDAT5 0x20 -#define BRDDAT4 0x10 -#define BRDSTB 0x10 -#define BRDCS 0x08 -#define BRDDAT3 0x08 -#define BRDDAT2 0x04 -#define BRDRW 0x04 -#define BRDRW_ULTRA2 0x02 -#define BRDCTL1 0x02 -#define BRDSTB_ULTRA2 0x01 -#define BRDCTL0 0x01 - -#define SEECTL 0x1e -#define EXTARBACK 0x80 -#define EXTARBREQ 0x40 -#define SEEMS 0x20 -#define SEERDY 0x10 -#define SEECS 0x08 -#define SEECK 0x04 -#define SEEDO 0x02 -#define SEEDI 0x01 - -#define SBLKCTL 0x1f -#define DIAGLEDEN 0x80 -#define DIAGLEDON 0x40 -#define AUTOFLUSHDIS 0x20 -#define ENAB40 0x08 -#define ENAB20 0x04 -#define SELWIDE 0x02 -#define XCVR 0x01 - -#define SRAM_BASE 0x20 - -#define TARG_SCSIRATE 0x20 - -#define ULTRA_ENB 0x30 - -#define DISC_DSB 0x32 - -#define MSG_OUT 0x34 - -#define DMAPARAMS 0x35 -#define PRELOADEN 0x80 -#define WIDEODD 0x40 -#define SCSIEN 0x20 -#define SDMAENACK 0x10 -#define SDMAEN 0x10 -#define HDMAEN 0x08 -#define HDMAENACK 0x08 -#define DIRECTION 0x04 -#define FIFOFLUSH 0x02 -#define FIFORESET 0x01 - -#define SEQ_FLAGS 0x36 -#define IDENTIFY_SEEN 0x80 -#define SCBPTR_VALID 0x20 -#define DPHASE 0x10 -#define AMTARGET 0x08 -#define WIDE_BUS 0x02 -#define TWIN_BUS 0x01 - -#define SAVED_TCL 0x37 - -#define SG_COUNT 0x38 - -#define SG_NEXT 0x39 - -#define LASTPHASE 0x3d -#define P_MESGIN 0xe0 -#define PHASE_MASK 0xe0 -#define P_STATUS 0xc0 -#define P_MESGOUT 0xa0 -#define P_COMMAND 0x80 -#define CDI 0x80 -#define IOI 0x40 -#define P_DATAIN 0x40 -#define MSGI 0x20 -#define P_BUSFREE 0x01 -#define P_DATAOUT 0x00 - -#define WAITING_SCBH 0x3e - -#define DISCONNECTED_SCBH 0x3f - -#define FREE_SCBH 0x40 - -#define HSCB_ADDR 0x41 - -#define SCBID_ADDR 0x45 - -#define TMODE_CMDADDR 0x49 - -#define KERNEL_QINPOS 0x4d - -#define QINPOS 0x4e - -#define QOUTPOS 0x4f - -#define TMODE_CMDADDR_NEXT 0x50 - -#define ARG_1 0x51 -#define RETURN_1 0x51 -#define SEND_MSG 0x80 -#define SEND_SENSE 0x40 -#define SEND_REJ 0x20 -#define MSGOUT_PHASEMIS 0x10 - -#define ARG_2 0x52 -#define RETURN_2 0x52 - -#define LAST_MSG 0x53 - -#define PREFETCH_CNT 0x54 - -#define SCSICONF 0x5a -#define TERM_ENB 0x80 -#define RESET_SCSI 0x40 -#define HWSCSIID 0x0f -#define HSCSIID 0x07 - -#define HOSTCONF 0x5d - -#define HA_274_BIOSCTRL 0x5f -#define BIOSMODE 0x30 -#define BIOSDISABLED 0x30 -#define CHANNEL_B_PRIMARY 0x08 - -#define SEQCTL 0x60 -#define PERRORDIS 0x80 -#define PAUSEDIS 0x40 -#define FAILDIS 0x20 -#define FASTMODE 0x10 -#define BRKADRINTEN 0x08 -#define STEP 0x04 -#define SEQRESET 0x02 -#define LOADRAM 0x01 - -#define SEQRAM 0x61 - -#define SEQADDR0 0x62 - -#define SEQADDR1 0x63 -#define SEQADDR1_MASK 0x01 - -#define ACCUM 0x64 - -#define SINDEX 0x65 - -#define DINDEX 0x66 - -#define ALLONES 0x69 - -#define ALLZEROS 0x6a - -#define NONE 0x6a - -#define FLAGS 0x6b -#define ZERO 0x02 -#define CARRY 0x01 - -#define SINDIR 0x6c - -#define DINDIR 0x6d - -#define FUNCTION1 0x6e - -#define STACK 0x6f - -#define TARG_OFFSET 0x70 - -#define BCTL 0x84 -#define ACE 0x08 -#define ENABLE 0x01 - -#define DSCOMMAND0 0x84 -#define INTSCBRAMSEL 0x08 -#define RAMPS 0x04 -#define USCBSIZE32 0x02 -#define CIOPARCKEN 0x01 - -#define DSCOMMAND 0x84 -#define CACHETHEN 0x80 -#define DPARCKEN 0x40 -#define MPARCKEN 0x20 -#define EXTREQLCK 0x10 - -#define BUSTIME 0x85 -#define BOFF 0xf0 -#define BON 0x0f - -#define BUSSPD 0x86 -#define DFTHRSH 0xc0 -#define STBOFF 0x38 -#define STBON 0x07 - -#define DSPCISTATUS 0x86 -#define DFTHRSH_100 0xc0 - -#define HCNTRL 0x87 -#define POWRDN 0x40 -#define SWINT 0x10 -#define IRQMS 0x08 -#define PAUSE 0x04 -#define INTEN 0x02 -#define CHIPRST 0x01 -#define CHIPRSTACK 0x01 - -#define HADDR 0x88 - -#define HCNT 0x8c - -#define SCBPTR 0x90 - -#define INTSTAT 0x91 -#define SEQINT_MASK 0xf1 -#define DATA_OVERRUN 0xe1 -#define MSGIN_PHASEMIS 0xd1 -#define TRACEPOINT2 0xc1 -#define SEQ_SG_FIXUP 0xb1 -#define AWAITING_MSG 0xa1 -#define RESIDUAL 0x81 -#define BAD_STATUS 0x71 -#define REJECT_MSG 0x61 -#define WIDE_RESIDUE 0x51 -#define EXTENDED_MSG 0x41 -#define NO_MATCH 0x31 -#define NO_IDENT 0x21 -#define SEND_REJECT 0x11 -#define INT_PEND 0x0f -#define BRKADRINT 0x08 -#define SCSIINT 0x04 -#define CMDCMPLT 0x02 -#define BAD_PHASE 0x01 -#define SEQINT 0x01 - -#define CLRINT 0x92 -#define CLRPARERR 0x10 -#define CLRBRKADRINT 0x08 -#define CLRSCSIINT 0x04 -#define CLRCMDINT 0x02 -#define CLRSEQINT 0x01 - -#define ERROR 0x92 -#define CIOPARERR 0x80 -#define PCIERRSTAT 0x40 -#define MPARERR 0x20 -#define DPARERR 0x10 -#define SQPARERR 0x08 -#define ILLOPCODE 0x04 -#define DSCTMOUT 0x02 -#define ILLSADDR 0x02 -#define ILLHADDR 0x01 - -#define DFCNTRL 0x93 - -#define DFSTATUS 0x94 -#define PRELOAD_AVAIL 0x80 -#define DWORDEMP 0x20 -#define MREQPEND 0x10 -#define HDONE 0x08 -#define DFTHRESH 0x04 -#define FIFOFULL 0x02 -#define FIFOEMP 0x01 - -#define DFDAT 0x99 - -#define SCBCNT 0x9a -#define SCBAUTO 0x80 -#define SCBCNT_MASK 0x1f - -#define QINFIFO 0x9b - -#define QINCNT 0x9c - -#define SCSIDATL_IMG 0x9c - -#define QOUTFIFO 0x9d - -#define CRCCONTROL1 0x9d -#define CRCONSEEN 0x80 -#define CRCVALCHKEN 0x40 -#define CRCENDCHKEN 0x20 -#define CRCREQCHKEN 0x10 -#define TARGCRCENDEN 0x08 -#define TARGCRCCNTEN 0x04 - -#define SCSIPHASE 0x9e -#define SP_STATUS 0x20 -#define SP_COMMAND 0x10 -#define SP_MSG_IN 0x08 -#define SP_MSG_OUT 0x04 -#define SP_DATA_IN 0x02 -#define SP_DATA_OUT 0x01 - -#define QOUTCNT 0x9e - -#define SFUNCT 0x9f -#define ALT_MODE 0x80 - -#define SCB_CONTROL 0xa0 -#define MK_MESSAGE 0x80 -#define DISCENB 0x40 -#define TAG_ENB 0x20 -#define DISCONNECTED 0x04 -#define SCB_TAG_TYPE 0x03 - -#define SCB_BASE 0xa0 - -#define SCB_TCL 0xa1 -#define TID 0xf0 -#define SELBUSB 0x08 -#define LID 0x07 - -#define SCB_TARGET_STATUS 0xa2 - -#define SCB_SGCOUNT 0xa3 - -#define SCB_SGPTR 0xa4 - -#define SCB_RESID_SGCNT 0xa8 - -#define SCB_RESID_DCNT 0xa9 - -#define SCB_DATAPTR 0xac - -#define SCB_DATACNT 0xb0 - -#define SCB_CMDPTR 0xb4 - -#define SCB_CMDLEN 0xb8 - -#define SCB_TAG 0xb9 - -#define SCB_NEXT 0xba - -#define SCB_PREV 0xbb - -#define SCB_BUSYTARGETS 0xbc - -#define SEECTL_2840 0xc0 -#define CS_2840 0x04 -#define CK_2840 0x02 -#define DO_2840 0x01 - -#define STATUS_2840 0xc1 -#define EEPROM_TF 0x80 -#define BIOS_SEL 0x60 -#define ADSEL 0x1e -#define DI_2840 0x01 - -#define CCHADDR 0xe0 - -#define CCHCNT 0xe8 - -#define CCSGRAM 0xe9 - -#define CCSGADDR 0xea - -#define CCSGCTL 0xeb -#define CCSGDONE 0x80 -#define CCSGEN 0x08 -#define FLAG 0x02 -#define CCSGRESET 0x01 - -#define CCSCBRAM 0xec - -#define CCSCBADDR 0xed - -#define CCSCBCTL 0xee -#define CCSCBDONE 0x80 -#define ARRDONE 0x40 -#define CCARREN 0x10 -#define CCSCBEN 0x08 -#define CCSCBDIR 0x04 -#define CCSCBRESET 0x01 - -#define CCSCBCNT 0xef - -#define CCSCBPTR 0xf1 - -#define HNSCB_QOFF 0xf4 - -#define HESCB_QOFF 0xf5 - -#define SNSCB_QOFF 0xf6 - -#define SESCB_QOFF 0xf7 - -#define SDSCB_QOFF 0xf8 - -#define QOFF_CTLSTA 0xfa -#define ESTABLISH_SCB_AVAIL 0x80 -#define SCB_AVAIL 0x40 -#define SNSCB_ROLLOVER 0x20 -#define SDSCB_ROLLOVER 0x10 -#define SESCB_ROLLOVER 0x08 -#define SCB_QSIZE 0x07 -#define SCB_QSIZE_256 0x06 - -#define DFF_THRSH 0xfb -#define WR_DFTHRSH 0x70 -#define WR_DFTHRSH_MAX 0x70 -#define WR_DFTHRSH_90 0x60 -#define WR_DFTHRSH_85 0x50 -#define WR_DFTHRSH_75 0x40 -#define WR_DFTHRSH_63 0x30 -#define WR_DFTHRSH_50 0x20 -#define WR_DFTHRSH_25 0x10 -#define RD_DFTHRSH_MAX 0x07 -#define RD_DFTHRSH 0x07 -#define RD_DFTHRSH_90 0x06 -#define RD_DFTHRSH_85 0x05 -#define RD_DFTHRSH_75 0x04 -#define RD_DFTHRSH_63 0x03 -#define RD_DFTHRSH_50 0x02 -#define RD_DFTHRSH_25 0x01 -#define WR_DFTHRSH_MIN 0x00 -#define RD_DFTHRSH_MIN 0x00 - -#define SG_CACHEPTR 0xfc -#define SG_USER_DATA 0xfc -#define LAST_SEG 0x02 -#define LAST_SEG_DONE 0x01 - - -#define CMD_GROUP2_BYTE_DELTA 0xfa -#define MAX_OFFSET_8BIT 0x0f -#define BUS_16_BIT 0x01 -#define QINFIFO_OFFSET 0x02 -#define CMD_GROUP5_BYTE_DELTA 0x0b -#define CMD_GROUP_CODE_SHIFT 0x05 -#define MAX_OFFSET_ULTRA2 0x7f -#define MAX_OFFSET_16BIT 0x08 -#define BUS_8_BIT 0x00 -#define QOUTFIFO_OFFSET 0x01 -#define UNTAGGEDSCB_OFFSET 0x00 -#define CCSGRAM_MAXSEGS 0x10 -#define SCB_LIST_NULL 0xff -#define SG_SIZEOF 0x08 -#define CMD_GROUP4_BYTE_DELTA 0x04 -#define CMD_GROUP0_BYTE_DELTA 0xfc -#define HOST_MSG 0xff -#define BUS_32_BIT 0x02 -#define CCSGADDR_MAX 0x80 - - -/* Downloaded Constant Definitions */ -#define TMODE_NUMCMDS 0x00 diff --git a/drivers/scsi/aic7xxx_old/aic7xxx_seq.c b/drivers/scsi/aic7xxx_old/aic7xxx_seq.c deleted file mode 100644 index e1bc140e973..00000000000 --- a/drivers/scsi/aic7xxx_old/aic7xxx_seq.c +++ /dev/null @@ -1,817 +0,0 @@ -/* - * DO NOT EDIT - This file is automatically generated. - */ -static unsigned char seqprog[] = { - 0xff, 0x6a, 0x06, 0x08, - 0x7f, 0x02, 0x04, 0x08, - 0x12, 0x6a, 0x00, 0x00, - 0xff, 0x6a, 0xd6, 0x09, - 0xff, 0x6a, 0xdc, 0x09, - 0x00, 0x65, 0xca, 0x58, - 0xf7, 0x01, 0x02, 0x08, - 0xff, 0x4e, 0xc8, 0x08, - 0xbf, 0x60, 0xc0, 0x08, - 0x60, 0x0b, 0x86, 0x68, - 0x40, 0x00, 0x0c, 0x68, - 0x08, 0x1f, 0x3e, 0x10, - 0x60, 0x0b, 0x86, 0x68, - 0x40, 0x00, 0x0c, 0x68, - 0x08, 0x1f, 0x3e, 0x10, - 0xff, 0x3e, 0x48, 0x60, - 0x40, 0xfa, 0x10, 0x78, - 0xff, 0xf6, 0xd4, 0x08, - 0x01, 0x4e, 0x9c, 0x18, - 0x40, 0x60, 0xc0, 0x00, - 0x00, 0x4d, 0x10, 0x70, - 0x01, 0x4e, 0x9c, 0x18, - 0xbf, 0x60, 0xc0, 0x08, - 0x00, 0x6a, 0x86, 0x5c, - 0xff, 0x4e, 0xc8, 0x18, - 0x02, 0x6a, 0x70, 0x5b, - 0xff, 0x52, 0x20, 0x09, - 0x0d, 0x6a, 0x6a, 0x00, - 0x00, 0x52, 0xe6, 0x5b, - 0x03, 0xb0, 0x52, 0x31, - 0xff, 0xb0, 0x52, 0x09, - 0xff, 0xb1, 0x54, 0x09, - 0xff, 0xb2, 0x56, 0x09, - 0xff, 0xa3, 0x50, 0x09, - 0xff, 0x3e, 0x74, 0x09, - 0xff, 0x90, 0x7c, 0x08, - 0xff, 0x3e, 0x20, 0x09, - 0x00, 0x65, 0x4e, 0x58, - 0x00, 0x65, 0x0c, 0x40, - 0xf7, 0x1f, 0xca, 0x08, - 0x08, 0xa1, 0xc8, 0x08, - 0x00, 0x65, 0xca, 0x00, - 0xff, 0x65, 0x3e, 0x08, - 0xf0, 0xa1, 0xc8, 0x08, - 0x0f, 0x0f, 0x1e, 0x08, - 0x00, 0x0f, 0x1e, 0x00, - 0xf0, 0xa1, 0xc8, 0x08, - 0x0f, 0x05, 0x0a, 0x08, - 0x00, 0x05, 0x0a, 0x00, - 0xff, 0x6a, 0x0c, 0x08, - 0x5a, 0x6a, 0x00, 0x04, - 0x12, 0x65, 0x02, 0x00, - 0x31, 0x6a, 0xca, 0x00, - 0x80, 0x37, 0x6e, 0x68, - 0xff, 0x65, 0xca, 0x18, - 0xff, 0x37, 0xdc, 0x08, - 0xff, 0x6e, 0xc8, 0x08, - 0x00, 0x6c, 0x76, 0x78, - 0x20, 0x01, 0x02, 0x00, - 0x4c, 0x37, 0xc8, 0x28, - 0x08, 0x1f, 0x7e, 0x78, - 0x08, 0x37, 0x6e, 0x00, - 0x08, 0x64, 0xc8, 0x00, - 0x70, 0x64, 0xca, 0x18, - 0xff, 0x6c, 0x0a, 0x08, - 0x20, 0x64, 0xca, 0x18, - 0xff, 0x6c, 0x08, 0x0c, - 0x40, 0x0b, 0x96, 0x68, - 0x20, 0x6a, 0x16, 0x00, - 0xf0, 0x19, 0x6e, 0x08, - 0x08, 0x6a, 0x18, 0x00, - 0x08, 0x11, 0x22, 0x00, - 0x08, 0x6a, 0x66, 0x58, - 0x08, 0x6a, 0x68, 0x00, - 0x00, 0x65, 0xaa, 0x40, - 0x12, 0x6a, 0x00, 0x00, - 0x40, 0x6a, 0x16, 0x00, - 0xff, 0x3e, 0x20, 0x09, - 0xff, 0xba, 0x7c, 0x08, - 0xff, 0xa1, 0x6e, 0x08, - 0x08, 0x6a, 0x18, 0x00, - 0x08, 0x11, 0x22, 0x00, - 0x08, 0x6a, 0x66, 0x58, - 0x80, 0x6a, 0x68, 0x00, - 0x80, 0x36, 0x6c, 0x00, - 0x00, 0x65, 0xba, 0x5b, - 0xff, 0x3d, 0xc8, 0x08, - 0xbf, 0x64, 0xe2, 0x78, - 0x80, 0x64, 0xc8, 0x71, - 0xa0, 0x64, 0xf8, 0x71, - 0xc0, 0x64, 0xf0, 0x71, - 0xe0, 0x64, 0x38, 0x72, - 0x01, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0xaa, 0x40, - 0xf7, 0x11, 0x22, 0x08, - 0x00, 0x65, 0xca, 0x58, - 0xff, 0x06, 0xd4, 0x08, - 0xf7, 0x01, 0x02, 0x08, - 0x09, 0x0c, 0xc4, 0x78, - 0x08, 0x0c, 0x0c, 0x68, - 0x01, 0x6a, 0x22, 0x01, - 0xff, 0x6a, 0x26, 0x09, - 0x02, 0x6a, 0x08, 0x30, - 0xff, 0x6a, 0x08, 0x08, - 0xdf, 0x01, 0x02, 0x08, - 0x01, 0x6a, 0x7a, 0x00, - 0xff, 0x6a, 0x6c, 0x0c, - 0x04, 0x14, 0x10, 0x31, - 0x03, 0xa9, 0x18, 0x31, - 0x03, 0xa9, 0x10, 0x30, - 0x08, 0x6a, 0xcc, 0x00, - 0xa9, 0x6a, 0xd0, 0x5b, - 0x00, 0x65, 0x02, 0x41, - 0xa8, 0x6a, 0x6a, 0x00, - 0x79, 0x6a, 0x6a, 0x00, - 0x40, 0x3d, 0xea, 0x68, - 0x04, 0x35, 0x6a, 0x00, - 0x00, 0x65, 0x2a, 0x5b, - 0x80, 0x6a, 0xd4, 0x01, - 0x10, 0x36, 0xd6, 0x68, - 0x10, 0x36, 0x6c, 0x00, - 0x07, 0xac, 0x10, 0x31, - 0x05, 0xa3, 0x70, 0x30, - 0x03, 0x8c, 0x10, 0x30, - 0x88, 0x6a, 0xcc, 0x00, - 0xac, 0x6a, 0xc8, 0x5b, - 0x00, 0x65, 0xc2, 0x5b, - 0x38, 0x6a, 0xcc, 0x00, - 0xa3, 0x6a, 0xcc, 0x5b, - 0xff, 0x38, 0x12, 0x69, - 0x80, 0x02, 0x04, 0x00, - 0xe7, 0x35, 0x6a, 0x08, - 0x03, 0x69, 0x18, 0x31, - 0x03, 0x69, 0x10, 0x30, - 0xff, 0x6a, 0x10, 0x00, - 0xff, 0x6a, 0x12, 0x00, - 0xff, 0x6a, 0x14, 0x00, - 0x22, 0x38, 0xc8, 0x28, - 0x01, 0x38, 0x1c, 0x61, - 0x02, 0x64, 0xc8, 0x00, - 0x01, 0x38, 0x1c, 0x61, - 0xbf, 0x35, 0x6a, 0x08, - 0xff, 0x64, 0xf8, 0x09, - 0xff, 0x35, 0x26, 0x09, - 0x80, 0x02, 0xa4, 0x69, - 0x10, 0x0c, 0x7a, 0x69, - 0x80, 0x94, 0x22, 0x79, - 0x00, 0x35, 0x0a, 0x5b, - 0x80, 0x02, 0xa4, 0x69, - 0xff, 0x65, 0x94, 0x79, - 0x01, 0x38, 0x70, 0x71, - 0xff, 0x38, 0x70, 0x18, - 0xff, 0x38, 0x94, 0x79, - 0x80, 0xea, 0x4a, 0x61, - 0xef, 0x38, 0xc8, 0x18, - 0x80, 0x6a, 0xc8, 0x00, - 0x00, 0x65, 0x3c, 0x49, - 0x33, 0x38, 0xc8, 0x28, - 0xff, 0x64, 0xd0, 0x09, - 0x04, 0x39, 0xc0, 0x31, - 0x09, 0x6a, 0xd6, 0x01, - 0x80, 0xeb, 0x42, 0x79, - 0xf7, 0xeb, 0xd6, 0x09, - 0x08, 0xeb, 0x46, 0x69, - 0x01, 0x6a, 0xd6, 0x01, - 0x08, 0xe9, 0x10, 0x31, - 0x03, 0x8c, 0x10, 0x30, - 0xff, 0x38, 0x70, 0x18, - 0x88, 0x6a, 0xcc, 0x00, - 0x39, 0x6a, 0xce, 0x5b, - 0x08, 0x6a, 0x18, 0x01, - 0xff, 0x6a, 0x1a, 0x09, - 0xff, 0x6a, 0x1c, 0x09, - 0x0d, 0x93, 0x26, 0x01, - 0x00, 0x65, 0x78, 0x5c, - 0x88, 0x6a, 0xcc, 0x00, - 0x00, 0x65, 0x6a, 0x5c, - 0x00, 0x65, 0xc2, 0x5b, - 0xff, 0x6a, 0xc8, 0x08, - 0x08, 0x39, 0x72, 0x18, - 0x00, 0x3a, 0x74, 0x20, - 0x00, 0x65, 0x02, 0x41, - 0x01, 0x0c, 0x6c, 0x79, - 0x10, 0x0c, 0x02, 0x79, - 0x10, 0x0c, 0x7a, 0x69, - 0x01, 0xfc, 0x70, 0x79, - 0xff, 0x6a, 0x70, 0x08, - 0x01, 0x0c, 0x76, 0x79, - 0x10, 0x0c, 0x02, 0x79, - 0x00, 0x65, 0xae, 0x59, - 0x01, 0xfc, 0x94, 0x69, - 0x40, 0x0d, 0x84, 0x69, - 0xb1, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0x94, 0x41, - 0x2e, 0xfc, 0xa2, 0x28, - 0x3f, 0x38, 0xc8, 0x08, - 0x00, 0x51, 0x94, 0x71, - 0xff, 0x6a, 0xc8, 0x08, - 0xf8, 0x39, 0x72, 0x18, - 0xff, 0x3a, 0x74, 0x20, - 0x01, 0x38, 0x70, 0x18, - 0x00, 0x65, 0x86, 0x41, - 0x03, 0x08, 0x52, 0x31, - 0xff, 0x38, 0x50, 0x09, - 0x12, 0x01, 0x02, 0x00, - 0xff, 0x08, 0x52, 0x09, - 0xff, 0x09, 0x54, 0x09, - 0xff, 0x0a, 0x56, 0x09, - 0xff, 0x38, 0x50, 0x09, - 0x00, 0x65, 0xaa, 0x40, - 0x10, 0x0c, 0xa4, 0x79, - 0x00, 0x65, 0xae, 0x59, - 0x7f, 0x02, 0x04, 0x08, - 0xe1, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0xaa, 0x40, - 0x04, 0x93, 0xc2, 0x69, - 0xdf, 0x93, 0x26, 0x09, - 0x20, 0x93, 0xb2, 0x69, - 0x02, 0x93, 0x26, 0x01, - 0x01, 0x94, 0xb6, 0x79, - 0x01, 0x94, 0xb6, 0x79, - 0x01, 0x94, 0xb6, 0x79, - 0x01, 0x94, 0xb6, 0x79, - 0x01, 0x94, 0xb6, 0x79, - 0x10, 0x94, 0xc0, 0x69, - 0xd7, 0x93, 0x26, 0x09, - 0x28, 0x93, 0xc4, 0x69, - 0xff, 0x6a, 0xd4, 0x0c, - 0x00, 0x65, 0x2a, 0x5b, - 0x05, 0xb4, 0x10, 0x31, - 0x02, 0x6a, 0x1a, 0x31, - 0x03, 0x8c, 0x10, 0x30, - 0x88, 0x6a, 0xcc, 0x00, - 0xb4, 0x6a, 0xcc, 0x5b, - 0xff, 0x6a, 0x1a, 0x09, - 0xff, 0x6a, 0x1c, 0x09, - 0x00, 0x65, 0xc2, 0x5b, - 0x3d, 0x6a, 0x0a, 0x5b, - 0xac, 0x6a, 0x26, 0x01, - 0x04, 0x0b, 0xde, 0x69, - 0x04, 0x0b, 0xe4, 0x69, - 0x10, 0x0c, 0xe0, 0x79, - 0x02, 0x03, 0xe8, 0x79, - 0x11, 0x0c, 0xe4, 0x79, - 0xd7, 0x93, 0x26, 0x09, - 0x28, 0x93, 0xea, 0x69, - 0x12, 0x01, 0x02, 0x00, - 0x00, 0x65, 0xaa, 0x40, - 0x00, 0x65, 0x2a, 0x5b, - 0xff, 0x06, 0x44, 0x09, - 0x00, 0x65, 0xaa, 0x40, - 0x10, 0x3d, 0x06, 0x00, - 0xff, 0x34, 0xca, 0x08, - 0x80, 0x65, 0x1c, 0x62, - 0x0f, 0xa1, 0xca, 0x08, - 0x07, 0xa1, 0xca, 0x08, - 0x40, 0xa0, 0xc8, 0x08, - 0x00, 0x65, 0xca, 0x00, - 0x80, 0x65, 0xca, 0x00, - 0x80, 0xa0, 0x0c, 0x7a, - 0xff, 0x65, 0x0c, 0x08, - 0x00, 0x65, 0x1e, 0x42, - 0x20, 0xa0, 0x24, 0x7a, - 0xff, 0x65, 0x0c, 0x08, - 0x00, 0x65, 0xba, 0x5b, - 0xa0, 0x3d, 0x2c, 0x62, - 0x23, 0xa0, 0x0c, 0x08, - 0x00, 0x65, 0xba, 0x5b, - 0xa0, 0x3d, 0x2c, 0x62, - 0x00, 0xb9, 0x24, 0x42, - 0xff, 0x65, 0x24, 0x62, - 0xa1, 0x6a, 0x22, 0x01, - 0xff, 0x6a, 0xd4, 0x08, - 0x10, 0x51, 0x2c, 0x72, - 0x40, 0x6a, 0x18, 0x00, - 0xff, 0x65, 0x0c, 0x08, - 0x00, 0x65, 0xba, 0x5b, - 0xa0, 0x3d, 0xf6, 0x71, - 0x40, 0x6a, 0x18, 0x00, - 0xff, 0x34, 0xa6, 0x08, - 0x80, 0x34, 0x34, 0x62, - 0x7f, 0xa0, 0x40, 0x09, - 0x08, 0x6a, 0x68, 0x00, - 0x00, 0x65, 0xaa, 0x40, - 0x64, 0x6a, 0x00, 0x5b, - 0x80, 0x64, 0xaa, 0x6a, - 0x04, 0x64, 0x8c, 0x72, - 0x02, 0x64, 0x92, 0x72, - 0x00, 0x6a, 0x54, 0x72, - 0x03, 0x64, 0xa6, 0x72, - 0x01, 0x64, 0x88, 0x72, - 0x07, 0x64, 0xe8, 0x72, - 0x08, 0x64, 0x50, 0x72, - 0x23, 0x64, 0xec, 0x72, - 0x11, 0x6a, 0x22, 0x01, - 0x07, 0x6a, 0xf2, 0x5a, - 0xff, 0x06, 0xd4, 0x08, - 0x00, 0x65, 0xaa, 0x40, - 0xff, 0xa8, 0x58, 0x6a, - 0xff, 0xa2, 0x70, 0x7a, - 0x01, 0x6a, 0x6a, 0x00, - 0x00, 0xb9, 0xe6, 0x5b, - 0xff, 0xa2, 0x70, 0x7a, - 0x71, 0x6a, 0x22, 0x01, - 0xff, 0x6a, 0xd4, 0x08, - 0x40, 0x51, 0x70, 0x62, - 0x0d, 0x6a, 0x6a, 0x00, - 0x00, 0xb9, 0xe6, 0x5b, - 0xff, 0x3e, 0x74, 0x09, - 0xff, 0x90, 0x7c, 0x08, - 0x00, 0x65, 0x4e, 0x58, - 0x00, 0x65, 0xbc, 0x40, - 0x20, 0xa0, 0x78, 0x6a, - 0xff, 0x37, 0xc8, 0x08, - 0x00, 0x6a, 0x90, 0x5b, - 0xff, 0x6a, 0xa6, 0x5b, - 0xff, 0xf8, 0xc8, 0x08, - 0xff, 0x4f, 0xc8, 0x08, - 0x01, 0x6a, 0x90, 0x5b, - 0x00, 0xb9, 0xa6, 0x5b, - 0x01, 0x4f, 0x9e, 0x18, - 0x02, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0x80, 0x5c, - 0x00, 0x65, 0xbc, 0x40, - 0x41, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0xaa, 0x40, - 0x04, 0xa0, 0x40, 0x01, - 0x00, 0x65, 0x98, 0x5c, - 0x00, 0x65, 0xbc, 0x40, - 0x10, 0x36, 0x50, 0x7a, - 0x05, 0x38, 0x46, 0x31, - 0x04, 0x14, 0x58, 0x31, - 0x03, 0xa9, 0x60, 0x31, - 0xa3, 0x6a, 0xcc, 0x00, - 0x38, 0x6a, 0xcc, 0x5b, - 0xac, 0x6a, 0xcc, 0x00, - 0x14, 0x6a, 0xce, 0x5b, - 0xa9, 0x6a, 0xd0, 0x5b, - 0x00, 0x65, 0x50, 0x42, - 0xef, 0x36, 0x6c, 0x08, - 0x00, 0x65, 0x50, 0x42, - 0x0f, 0x64, 0xc8, 0x08, - 0x07, 0x64, 0xc8, 0x08, - 0x00, 0x37, 0x6e, 0x00, - 0xff, 0x6a, 0xa4, 0x00, - 0x00, 0x65, 0x60, 0x5b, - 0xff, 0x51, 0xbc, 0x72, - 0x20, 0x36, 0xc6, 0x7a, - 0x00, 0x90, 0x4e, 0x5b, - 0x00, 0x65, 0xc8, 0x42, - 0xff, 0x06, 0xd4, 0x08, - 0x00, 0x65, 0xba, 0x5b, - 0xe0, 0x3d, 0xe2, 0x62, - 0x20, 0x12, 0xe2, 0x62, - 0x51, 0x6a, 0xf6, 0x5a, - 0x00, 0x65, 0x48, 0x5b, - 0xff, 0x37, 0xc8, 0x08, - 0x00, 0xa1, 0xda, 0x62, - 0x04, 0xa0, 0xda, 0x7a, - 0xfb, 0xa0, 0x40, 0x09, - 0x80, 0x36, 0x6c, 0x00, - 0x80, 0xa0, 0x50, 0x7a, - 0x7f, 0xa0, 0x40, 0x09, - 0xff, 0x6a, 0xf2, 0x5a, - 0x00, 0x65, 0x50, 0x42, - 0x04, 0xa0, 0xe0, 0x7a, - 0x00, 0x65, 0x98, 0x5c, - 0x00, 0x65, 0xe2, 0x42, - 0x00, 0x65, 0x80, 0x5c, - 0x31, 0x6a, 0x22, 0x01, - 0x0c, 0x6a, 0xf2, 0x5a, - 0x00, 0x65, 0x50, 0x42, - 0x61, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0x50, 0x42, - 0x51, 0x6a, 0xf6, 0x5a, - 0x51, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0x50, 0x42, - 0x10, 0x3d, 0x06, 0x00, - 0xff, 0x65, 0x68, 0x0c, - 0xff, 0x06, 0xd4, 0x08, - 0x01, 0x0c, 0xf8, 0x7a, - 0x04, 0x0c, 0xfa, 0x6a, - 0xe0, 0x03, 0x7a, 0x08, - 0xe0, 0x3d, 0x06, 0x63, - 0xff, 0x65, 0xcc, 0x08, - 0xff, 0x12, 0xda, 0x0c, - 0xff, 0x06, 0xd4, 0x0c, - 0xd1, 0x6a, 0x22, 0x01, - 0x00, 0x65, 0xaa, 0x40, - 0xff, 0x65, 0x26, 0x09, - 0x01, 0x0b, 0x1a, 0x6b, - 0x10, 0x0c, 0x0c, 0x7b, - 0x04, 0x0b, 0x14, 0x6b, - 0xff, 0x6a, 0xca, 0x08, - 0x04, 0x93, 0x18, 0x6b, - 0x01, 0x94, 0x16, 0x7b, - 0x10, 0x94, 0x18, 0x6b, - 0x80, 0x3d, 0x1e, 0x73, - 0x0f, 0x04, 0x22, 0x6b, - 0x02, 0x03, 0x22, 0x7b, - 0x11, 0x0c, 0x1e, 0x7b, - 0xc7, 0x93, 0x26, 0x09, - 0xff, 0x99, 0xd4, 0x08, - 0x38, 0x93, 0x24, 0x6b, - 0xff, 0x6a, 0xd4, 0x0c, - 0x80, 0x36, 0x28, 0x6b, - 0x21, 0x6a, 0x22, 0x05, - 0xff, 0x65, 0x20, 0x09, - 0xff, 0x51, 0x36, 0x63, - 0xff, 0x37, 0xc8, 0x08, - 0xa1, 0x6a, 0x42, 0x43, - 0xff, 0x51, 0xc8, 0x08, - 0xb9, 0x6a, 0x42, 0x43, - 0xff, 0x90, 0xa4, 0x08, - 0xff, 0xba, 0x46, 0x73, - 0xff, 0xba, 0x20, 0x09, - 0xff, 0x65, 0xca, 0x18, - 0x00, 0x6c, 0x3a, 0x63, - 0xff, 0x90, 0xca, 0x0c, - 0xff, 0x6a, 0xca, 0x04, - 0x20, 0x36, 0x5a, 0x7b, - 0x00, 0x90, 0x2e, 0x5b, - 0xff, 0x65, 0x5a, 0x73, - 0xff, 0x52, 0x58, 0x73, - 0xff, 0xba, 0xcc, 0x08, - 0xff, 0x52, 0x20, 0x09, - 0xff, 0x66, 0x74, 0x09, - 0xff, 0x65, 0x20, 0x0d, - 0xff, 0xba, 0x7e, 0x0c, - 0x00, 0x6a, 0x86, 0x5c, - 0x0d, 0x6a, 0x6a, 0x00, - 0x00, 0x51, 0xe6, 0x43, - 0xff, 0x3f, 0xb4, 0x73, - 0xff, 0x6a, 0xa2, 0x00, - 0x00, 0x3f, 0x2e, 0x5b, - 0xff, 0x65, 0xb4, 0x73, - 0x20, 0x36, 0x6c, 0x00, - 0x20, 0xa0, 0x6e, 0x6b, - 0xff, 0xb9, 0xa2, 0x0c, - 0xff, 0x6a, 0xa2, 0x04, - 0xff, 0x65, 0xa4, 0x08, - 0xe0, 0x6a, 0xcc, 0x00, - 0x45, 0x6a, 0xda, 0x5b, - 0x01, 0x6a, 0xd0, 0x01, - 0x09, 0x6a, 0xd6, 0x01, - 0x80, 0xeb, 0x7a, 0x7b, - 0x01, 0x6a, 0xd6, 0x01, - 0x01, 0xe9, 0xa4, 0x34, - 0x88, 0x6a, 0xcc, 0x00, - 0x45, 0x6a, 0xda, 0x5b, - 0x01, 0x6a, 0x18, 0x01, - 0xff, 0x6a, 0x1a, 0x09, - 0xff, 0x6a, 0x1c, 0x09, - 0x0d, 0x6a, 0x26, 0x01, - 0x00, 0x65, 0x78, 0x5c, - 0xff, 0x99, 0xa4, 0x0c, - 0xff, 0x65, 0xa4, 0x08, - 0xe0, 0x6a, 0xcc, 0x00, - 0x45, 0x6a, 0xda, 0x5b, - 0x01, 0x6a, 0xd0, 0x01, - 0x01, 0x6a, 0xdc, 0x05, - 0x88, 0x6a, 0xcc, 0x00, - 0x45, 0x6a, 0xda, 0x5b, - 0x01, 0x6a, 0x18, 0x01, - 0xff, 0x6a, 0x1a, 0x09, - 0xff, 0x6a, 0x1c, 0x09, - 0x01, 0x6a, 0x26, 0x05, - 0x01, 0x65, 0xd8, 0x31, - 0x09, 0xee, 0xdc, 0x01, - 0x80, 0xee, 0xaa, 0x7b, - 0xff, 0x6a, 0xdc, 0x0d, - 0xff, 0x65, 0x32, 0x09, - 0x0a, 0x93, 0x26, 0x01, - 0x00, 0x65, 0x78, 0x44, - 0xff, 0x37, 0xc8, 0x08, - 0x00, 0x6a, 0x70, 0x5b, - 0xff, 0x52, 0xa2, 0x0c, - 0x01, 0x0c, 0xba, 0x7b, - 0x04, 0x0c, 0xba, 0x6b, - 0xe0, 0x03, 0x06, 0x08, - 0xe0, 0x03, 0x7a, 0x0c, - 0xff, 0x8c, 0x10, 0x08, - 0xff, 0x8d, 0x12, 0x08, - 0xff, 0x8e, 0x14, 0x0c, - 0xff, 0x6c, 0xda, 0x08, - 0xff, 0x6c, 0xda, 0x08, - 0xff, 0x6c, 0xda, 0x08, - 0xff, 0x6c, 0xda, 0x08, - 0xff, 0x6c, 0xda, 0x08, - 0xff, 0x6c, 0xda, 0x08, - 0xff, 0x6c, 0xda, 0x0c, - 0x3d, 0x64, 0xa4, 0x28, - 0x55, 0x64, 0xc8, 0x28, - 0x00, 0x6c, 0xda, 0x18, - 0xff, 0x52, 0xc8, 0x08, - 0x00, 0x6c, 0xda, 0x20, - 0xff, 0x6a, 0xc8, 0x08, - 0x00, 0x6c, 0xda, 0x20, - 0x00, 0x6c, 0xda, 0x24, - 0xff, 0x65, 0xc8, 0x08, - 0xe0, 0x6a, 0xcc, 0x00, - 0x41, 0x6a, 0xd6, 0x5b, - 0xff, 0x90, 0xe2, 0x09, - 0x20, 0x6a, 0xd0, 0x01, - 0x04, 0x35, 0xf8, 0x7b, - 0x1d, 0x6a, 0xdc, 0x01, - 0xdc, 0xee, 0xf4, 0x63, - 0x00, 0x65, 0x0e, 0x44, - 0x01, 0x6a, 0xdc, 0x01, - 0x20, 0xa0, 0xd8, 0x31, - 0x09, 0xee, 0xdc, 0x01, - 0x80, 0xee, 0xfe, 0x7b, - 0x11, 0x6a, 0xdc, 0x01, - 0x50, 0xee, 0x02, 0x64, - 0x20, 0x6a, 0xd0, 0x01, - 0x09, 0x6a, 0xdc, 0x01, - 0x88, 0xee, 0x08, 0x64, - 0x19, 0x6a, 0xdc, 0x01, - 0xd8, 0xee, 0x0c, 0x64, - 0xff, 0x6a, 0xdc, 0x09, - 0x18, 0xee, 0x10, 0x6c, - 0xff, 0x6a, 0xd4, 0x0c, - 0x88, 0x6a, 0xcc, 0x00, - 0x41, 0x6a, 0xd6, 0x5b, - 0x20, 0x6a, 0x18, 0x01, - 0xff, 0x6a, 0x1a, 0x09, - 0xff, 0x6a, 0x1c, 0x09, - 0xff, 0x35, 0x26, 0x09, - 0x04, 0x35, 0x3c, 0x6c, - 0xa0, 0x6a, 0xca, 0x00, - 0x20, 0x65, 0xc8, 0x18, - 0xff, 0x6c, 0x32, 0x09, - 0xff, 0x6c, 0x32, 0x09, - 0xff, 0x6c, 0x32, 0x09, - 0xff, 0x6c, 0x32, 0x09, - 0xff, 0x6c, 0x32, 0x09, - 0xff, 0x6c, 0x32, 0x09, - 0xff, 0x6c, 0x32, 0x09, - 0xff, 0x6c, 0x32, 0x09, - 0x00, 0x65, 0x26, 0x64, - 0x0a, 0x93, 0x26, 0x01, - 0x00, 0x65, 0x78, 0x44, - 0xa0, 0x6a, 0xcc, 0x00, - 0xe8, 0x6a, 0xc8, 0x00, - 0x01, 0x94, 0x40, 0x6c, - 0x10, 0x94, 0x42, 0x6c, - 0x08, 0x94, 0x54, 0x6c, - 0x08, 0x94, 0x54, 0x6c, - 0x08, 0x94, 0x54, 0x6c, - 0x00, 0x65, 0x68, 0x5c, - 0x08, 0x64, 0xc8, 0x18, - 0x00, 0x8c, 0xca, 0x18, - 0x00, 0x65, 0x4a, 0x4c, - 0x00, 0x65, 0x40, 0x44, - 0xf7, 0x93, 0x26, 0x09, - 0x08, 0x93, 0x56, 0x6c, - 0x00, 0x65, 0x68, 0x5c, - 0x08, 0x64, 0xc8, 0x18, - 0x08, 0x64, 0x58, 0x64, - 0xff, 0x6a, 0xd4, 0x0c, - 0x00, 0x65, 0x78, 0x5c, - 0x00, 0x65, 0x68, 0x5c, - 0x00, 0x65, 0x68, 0x5c, - 0x00, 0x65, 0x68, 0x5c, - 0xff, 0x99, 0xda, 0x08, - 0xff, 0x99, 0xda, 0x08, - 0xff, 0x99, 0xda, 0x08, - 0xff, 0x99, 0xda, 0x08, - 0xff, 0x99, 0xda, 0x08, - 0xff, 0x99, 0xda, 0x08, - 0xff, 0x99, 0xda, 0x08, - 0xff, 0x99, 0xda, 0x0c, - 0x08, 0x94, 0x78, 0x7c, - 0xf7, 0x93, 0x26, 0x09, - 0x08, 0x93, 0x7c, 0x6c, - 0xff, 0x6a, 0xd4, 0x0c, - 0xff, 0x40, 0x74, 0x09, - 0xff, 0x90, 0x80, 0x08, - 0xff, 0x6a, 0x72, 0x05, - 0xff, 0x40, 0x94, 0x64, - 0xff, 0x3f, 0x8c, 0x64, - 0xff, 0x6a, 0xca, 0x04, - 0xff, 0x3f, 0x20, 0x09, - 0x01, 0x6a, 0x6a, 0x00, - 0x00, 0xb9, 0xe6, 0x5b, - 0xff, 0xba, 0x7e, 0x0c, - 0xff, 0x40, 0x20, 0x09, - 0xff, 0xba, 0x80, 0x0c, - 0xff, 0x3f, 0x74, 0x09, - 0xff, 0x90, 0x7e, 0x0c, -}; - -static int aic7xxx_patch15_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch15_func(struct aic7xxx_host *p) -{ - return ((p->bugs & AHC_BUG_SCBCHAN_UPLOAD) != 0); -} - -static int aic7xxx_patch14_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch14_func(struct aic7xxx_host *p) -{ - return ((p->bugs & AHC_BUG_PCI_2_1_RETRY) != 0); -} - -static int aic7xxx_patch13_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch13_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_WIDE) != 0); -} - -static int aic7xxx_patch12_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch12_func(struct aic7xxx_host *p) -{ - return ((p->bugs & AHC_BUG_AUTOFLUSH) != 0); -} - -static int aic7xxx_patch11_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch11_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_ULTRA2) == 0); -} - -static int aic7xxx_patch10_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch10_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_CMD_CHAN) == 0); -} - -static int aic7xxx_patch9_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch9_func(struct aic7xxx_host *p) -{ - return ((p->chip & AHC_CHIPID_MASK) == AHC_AIC7895); -} - -static int aic7xxx_patch8_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch8_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_ULTRA) != 0); -} - -static int aic7xxx_patch7_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch7_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_ULTRA2) != 0); -} - -static int aic7xxx_patch6_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch6_func(struct aic7xxx_host *p) -{ - return ((p->flags & AHC_PAGESCBS) == 0); -} - -static int aic7xxx_patch5_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch5_func(struct aic7xxx_host *p) -{ - return ((p->flags & AHC_PAGESCBS) != 0); -} - -static int aic7xxx_patch4_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch4_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_QUEUE_REGS) != 0); -} - -static int aic7xxx_patch3_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch3_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_TWIN) != 0); -} - -static int aic7xxx_patch2_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch2_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_QUEUE_REGS) == 0); -} - -static int aic7xxx_patch1_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch1_func(struct aic7xxx_host *p) -{ - return ((p->features & AHC_CMD_CHAN) != 0); -} - -static int aic7xxx_patch0_func(struct aic7xxx_host *p); - -static int -aic7xxx_patch0_func(struct aic7xxx_host *p) -{ - return (0); -} - -struct sequencer_patch { - int (*patch_func)(struct aic7xxx_host *); - unsigned int begin :10, - skip_instr :10, - skip_patch :12; -} sequencer_patches[] = { - { aic7xxx_patch1_func, 3, 2, 1 }, - { aic7xxx_patch2_func, 7, 1, 1 }, - { aic7xxx_patch2_func, 8, 1, 1 }, - { aic7xxx_patch3_func, 11, 4, 1 }, - { aic7xxx_patch4_func, 16, 3, 2 }, - { aic7xxx_patch0_func, 19, 4, 1 }, - { aic7xxx_patch5_func, 23, 1, 1 }, - { aic7xxx_patch6_func, 26, 1, 1 }, - { aic7xxx_patch1_func, 29, 1, 2 }, - { aic7xxx_patch0_func, 30, 3, 1 }, - { aic7xxx_patch3_func, 39, 4, 1 }, - { aic7xxx_patch7_func, 43, 3, 2 }, - { aic7xxx_patch0_func, 46, 3, 1 }, - { aic7xxx_patch8_func, 52, 7, 1 }, - { aic7xxx_patch3_func, 60, 3, 1 }, - { aic7xxx_patch7_func, 63, 2, 1 }, - { aic7xxx_patch7_func, 102, 1, 2 }, - { aic7xxx_patch0_func, 103, 2, 1 }, - { aic7xxx_patch7_func, 107, 2, 1 }, - { aic7xxx_patch9_func, 109, 1, 1 }, - { aic7xxx_patch10_func, 110, 2, 1 }, - { aic7xxx_patch7_func, 113, 1, 2 }, - { aic7xxx_patch0_func, 114, 1, 1 }, - { aic7xxx_patch1_func, 118, 1, 1 }, - { aic7xxx_patch1_func, 121, 3, 3 }, - { aic7xxx_patch11_func, 123, 1, 1 }, - { aic7xxx_patch0_func, 124, 5, 1 }, - { aic7xxx_patch7_func, 132, 1, 1 }, - { aic7xxx_patch9_func, 133, 1, 1 }, - { aic7xxx_patch10_func, 134, 3, 1 }, - { aic7xxx_patch7_func, 137, 3, 2 }, - { aic7xxx_patch0_func, 140, 2, 1 }, - { aic7xxx_patch7_func, 142, 5, 2 }, - { aic7xxx_patch0_func, 147, 3, 1 }, - { aic7xxx_patch7_func, 150, 1, 2 }, - { aic7xxx_patch0_func, 151, 2, 1 }, - { aic7xxx_patch1_func, 153, 15, 4 }, - { aic7xxx_patch11_func, 166, 1, 2 }, - { aic7xxx_patch0_func, 167, 1, 1 }, - { aic7xxx_patch0_func, 168, 10, 1 }, - { aic7xxx_patch7_func, 181, 1, 2 }, - { aic7xxx_patch0_func, 182, 2, 1 }, - { aic7xxx_patch7_func, 184, 18, 1 }, - { aic7xxx_patch1_func, 202, 3, 3 }, - { aic7xxx_patch7_func, 204, 1, 1 }, - { aic7xxx_patch0_func, 205, 4, 1 }, - { aic7xxx_patch7_func, 210, 2, 1 }, - { aic7xxx_patch7_func, 215, 13, 3 }, - { aic7xxx_patch12_func, 218, 1, 1 }, - { aic7xxx_patch12_func, 219, 4, 1 }, - { aic7xxx_patch1_func, 229, 3, 3 }, - { aic7xxx_patch11_func, 231, 1, 1 }, - { aic7xxx_patch0_func, 232, 5, 1 }, - { aic7xxx_patch11_func, 237, 1, 2 }, - { aic7xxx_patch0_func, 238, 9, 1 }, - { aic7xxx_patch13_func, 254, 1, 2 }, - { aic7xxx_patch0_func, 255, 1, 1 }, - { aic7xxx_patch4_func, 316, 1, 2 }, - { aic7xxx_patch0_func, 317, 1, 1 }, - { aic7xxx_patch2_func, 320, 1, 1 }, - { aic7xxx_patch1_func, 330, 3, 2 }, - { aic7xxx_patch0_func, 333, 5, 1 }, - { aic7xxx_patch13_func, 341, 1, 2 }, - { aic7xxx_patch0_func, 342, 1, 1 }, - { aic7xxx_patch5_func, 347, 1, 1 }, - { aic7xxx_patch11_func, 389, 15, 2 }, - { aic7xxx_patch14_func, 402, 1, 1 }, - { aic7xxx_patch1_func, 441, 7, 2 }, - { aic7xxx_patch0_func, 448, 8, 1 }, - { aic7xxx_patch1_func, 457, 4, 2 }, - { aic7xxx_patch0_func, 461, 6, 1 }, - { aic7xxx_patch1_func, 467, 4, 2 }, - { aic7xxx_patch0_func, 471, 3, 1 }, - { aic7xxx_patch10_func, 481, 10, 1 }, - { aic7xxx_patch1_func, 500, 22, 5 }, - { aic7xxx_patch11_func, 508, 4, 1 }, - { aic7xxx_patch7_func, 512, 7, 3 }, - { aic7xxx_patch15_func, 512, 5, 2 }, - { aic7xxx_patch0_func, 517, 2, 1 }, - { aic7xxx_patch10_func, 522, 50, 3 }, - { aic7xxx_patch14_func, 543, 17, 2 }, - { aic7xxx_patch0_func, 560, 4, 1 }, - { aic7xxx_patch10_func, 572, 4, 1 }, - { aic7xxx_patch5_func, 576, 2, 1 }, - { aic7xxx_patch5_func, 579, 9, 1 }, - -}; diff --git a/drivers/scsi/aic7xxx_old/scsi_message.h b/drivers/scsi/aic7xxx_old/scsi_message.h deleted file mode 100644 index a79f89c6517..00000000000 --- a/drivers/scsi/aic7xxx_old/scsi_message.h +++ /dev/null @@ -1,49 +0,0 @@ -/* Messages (1 byte) */ /* I/T (M)andatory or (O)ptional */ -#define MSG_CMDCOMPLETE 0x00 /* M/M */ -#define MSG_EXTENDED 0x01 /* O/O */ -#define MSG_SAVEDATAPOINTER 0x02 /* O/O */ -#define MSG_RESTOREPOINTERS 0x03 /* O/O */ -#define MSG_DISCONNECT 0x04 /* O/O */ -#define MSG_INITIATOR_DET_ERR 0x05 /* M/M */ -#define MSG_ABORT 0x06 /* O/M */ -#define MSG_MESSAGE_REJECT 0x07 /* M/M */ -#define MSG_NOOP 0x08 /* M/M */ -#define MSG_PARITY_ERROR 0x09 /* M/M */ -#define MSG_LINK_CMD_COMPLETE 0x0a /* O/O */ -#define MSG_LINK_CMD_COMPLETEF 0x0b /* O/O */ -#define MSG_BUS_DEV_RESET 0x0c /* O/M */ -#define MSG_ABORT_TAG 0x0d /* O/O */ -#define MSG_CLEAR_QUEUE 0x0e /* O/O */ -#define MSG_INIT_RECOVERY 0x0f /* O/O */ -#define MSG_REL_RECOVERY 0x10 /* O/O */ -#define MSG_TERM_IO_PROC 0x11 /* O/O */ - -/* Messages (2 byte) */ -#define MSG_SIMPLE_Q_TAG 0x20 /* O/O */ -#define MSG_HEAD_OF_Q_TAG 0x21 /* O/O */ -#define MSG_ORDERED_Q_TAG 0x22 /* O/O */ -#define MSG_IGN_WIDE_RESIDUE 0x23 /* O/O */ - -/* Identify message */ /* M/M */ -#define MSG_IDENTIFYFLAG 0x80 -#define MSG_IDENTIFY_DISCFLAG 0x40 -#define MSG_IDENTIFY(lun, disc) (((disc) ? 0xc0 : MSG_IDENTIFYFLAG) | (lun)) -#define MSG_ISIDENTIFY(m) ((m) & MSG_IDENTIFYFLAG) - -/* Extended messages (opcode and length) */ -#define MSG_EXT_SDTR 0x01 -#define MSG_EXT_SDTR_LEN 0x03 - -#define MSG_EXT_WDTR 0x03 -#define MSG_EXT_WDTR_LEN 0x02 -#define MSG_EXT_WDTR_BUS_8_BIT 0x00 -#define MSG_EXT_WDTR_BUS_16_BIT 0x01 -#define MSG_EXT_WDTR_BUS_32_BIT 0x02 - -#define MSG_EXT_PPR 0x04 -#define MSG_EXT_PPR_LEN 0x06 -#define MSG_EXT_PPR_OPTION_ST 0x00 -#define MSG_EXT_PPR_OPTION_DT_CRC 0x02 -#define MSG_EXT_PPR_OPTION_DT_UNITS 0x03 -#define MSG_EXT_PPR_OPTION_DT_CRC_QUICK 0x04 -#define MSG_EXT_PPR_OPTION_DT_UNITS_QUICK 0x05 diff --git a/drivers/scsi/aic7xxx_old/sequencer.h b/drivers/scsi/aic7xxx_old/sequencer.h deleted file mode 100644 index ee66855222b..00000000000 --- a/drivers/scsi/aic7xxx_old/sequencer.h +++ /dev/null @@ -1,135 +0,0 @@ -/* - * Instruction formats for the sequencer program downloaded to - * Aic7xxx SCSI host adapters - * - * Copyright (c) 1997, 1998 Justin T. Gibbs. - * All rights reserved. - * - * Redistribution and use in source and binary forms, with or without - * modification, are permitted provided that the following conditions - * are met: - * 1. Redistributions of source code must retain the above copyright - * notice, this list of conditions, and the following disclaimer, - * without modification, immediately at the beginning of the file. - * 2. The name of the author may not be used to endorse or promote products - * derived from this software without specific prior written permission. - * - * Where this Software is combined with software released under the terms of - * the GNU General Public License ("GPL") and the terms of the GPL would require the - * combined work to also be released under the terms of the GPL, the terms - * and conditions of this License will apply in addition to those of the - * GPL with the exception of any terms or conditions of this License that - * conflict with, or are expressly prohibited by, the GPL. - * - * THIS SOFTWARE IS PROVIDED BY THE AUTHOR AND CONTRIBUTORS ``AS IS'' AND - * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE - * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE - * ARE DISCLAIMED. IN NO EVENT SHALL THE AUTHOR OR CONTRIBUTORS BE LIABLE FOR - * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL - * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS - * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) - * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT - * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY - * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF - * SUCH DAMAGE. - * - * $Id: sequencer.h,v 1.3 1997/09/27 19:37:31 gibbs Exp $ - */ - -#ifdef __LITTLE_ENDIAN_BITFIELD -struct ins_format1 { - unsigned int - immediate : 8, - source : 9, - destination : 9, - ret : 1, - opcode : 4, - parity : 1; -}; - -struct ins_format2 { - unsigned int - shift_control : 8, - source : 9, - destination : 9, - ret : 1, - opcode : 4, - parity : 1; -}; - -struct ins_format3 { - unsigned int - immediate : 8, - source : 9, - address : 10, - opcode : 4, - parity : 1; -}; -#elif defined(__BIG_ENDIAN_BITFIELD) -struct ins_format1 { - unsigned int - parity : 1, - opcode : 4, - ret : 1, - destination : 9, - source : 9, - immediate : 8; -}; - -struct ins_format2 { - unsigned int - parity : 1, - opcode : 4, - ret : 1, - destination : 9, - source : 9, - shift_control : 8; -}; - -struct ins_format3 { - unsigned int - parity : 1, - opcode : 4, - address : 10, - source : 9, - immediate : 8; -}; -#endif - -union ins_formats { - struct ins_format1 format1; - struct ins_format2 format2; - struct ins_format3 format3; - unsigned char bytes[4]; - unsigned int integer; -}; -struct instruction { - union ins_formats format; - unsigned int srcline; - struct symbol *patch_label; - struct { - struct instruction *stqe_next; - } links; -}; - -#define AIC_OP_OR 0x0 -#define AIC_OP_AND 0x1 -#define AIC_OP_XOR 0x2 -#define AIC_OP_ADD 0x3 -#define AIC_OP_ADC 0x4 -#define AIC_OP_ROL 0x5 -#define AIC_OP_BMOV 0x6 - -#define AIC_OP_JMP 0x8 -#define AIC_OP_JC 0x9 -#define AIC_OP_JNC 0xa -#define AIC_OP_CALL 0xb -#define AIC_OP_JNE 0xc -#define AIC_OP_JNZ 0xd -#define AIC_OP_JE 0xe -#define AIC_OP_JZ 0xf - -/* Pseudo Ops */ -#define AIC_OP_SHL 0x10 -#define AIC_OP_SHR 0x20 -#define AIC_OP_ROR 0x30 diff --git a/drivers/scsi/be2iscsi/be_iscsi.c b/drivers/scsi/be2iscsi/be_iscsi.c index ffadbee0b4d..889066d9d6f 100644 --- a/drivers/scsi/be2iscsi/be_iscsi.c +++ b/drivers/scsi/be2iscsi/be_iscsi.c @@ -541,10 +541,8 @@ static int be2iscsi_get_if_param(struct beiscsi_hba *phba, ip_type = BE2_IPV6; len = mgmt_get_if_info(phba, ip_type, &if_info); - if (len) { - kfree(if_info); + if (len) return len; - } switch (param) { case ISCSI_NET_PARAM_IPV4_ADDR: @@ -569,7 +567,7 @@ static int be2iscsi_get_if_param(struct beiscsi_hba *phba, break; case ISCSI_NET_PARAM_VLAN_ID: if (if_info->vlan_priority == BEISCSI_VLAN_DISABLE) - return -EINVAL; + len = -EINVAL; else len = sprintf(buf, "%d\n", (if_info->vlan_priority & @@ -577,7 +575,7 @@ static int be2iscsi_get_if_param(struct beiscsi_hba *phba, break; case ISCSI_NET_PARAM_VLAN_PRIORITY: if (if_info->vlan_priority == BEISCSI_VLAN_DISABLE) - return -EINVAL; + len = -EINVAL; else len = sprintf(buf, "%d\n", ((if_info->vlan_priority >> 13) & diff --git a/drivers/scsi/bfa/bfa_core.c b/drivers/scsi/bfa/bfa_core.c index 520540a5fef..e3f67b097a5 100644 --- a/drivers/scsi/bfa/bfa_core.c +++ b/drivers/scsi/bfa/bfa_core.c @@ -1367,10 +1367,6 @@ bfa_faa_query(struct bfa_s *bfa, struct bfa_faa_attr_s *attr, struct bfa_iocfc_s *iocfc = &bfa->iocfc; bfa_status_t status; - iocfc->faa_args.faa_attr = attr; - iocfc->faa_args.faa_cb.faa_cbfn = cbfn; - iocfc->faa_args.faa_cb.faa_cbarg = cbarg; - status = bfa_faa_validate_request(bfa); if (status != BFA_STATUS_OK) return status; @@ -1378,6 +1374,10 @@ bfa_faa_query(struct bfa_s *bfa, struct bfa_faa_attr_s *attr, if (iocfc->faa_args.busy == BFA_TRUE) return BFA_STATUS_DEVBUSY; + iocfc->faa_args.faa_attr = attr; + iocfc->faa_args.faa_cb.faa_cbfn = cbfn; + iocfc->faa_args.faa_cb.faa_cbarg = cbarg; + iocfc->faa_args.busy = BFA_TRUE; memset(&faa_attr_req, 0, sizeof(struct bfi_faa_query_s)); bfi_h2i_set(faa_attr_req.mh, BFI_MC_IOCFC, diff --git a/drivers/scsi/bfa/bfa_defs.h b/drivers/scsi/bfa/bfa_defs.h index d40a79f5265..877b86dd283 100644 --- a/drivers/scsi/bfa/bfa_defs.h +++ b/drivers/scsi/bfa/bfa_defs.h @@ -132,6 +132,7 @@ enum bfa_status { BFA_STATUS_ETIMER = 5, /* Timer expired - Retry, if persists, * contact support */ BFA_STATUS_EPROTOCOL = 6, /* Protocol error */ + BFA_STATUS_BADFLASH = 9, /* Flash is bad */ BFA_STATUS_SFP_UNSUPP = 10, /* Unsupported SFP - Replace SFP */ BFA_STATUS_UNKNOWN_VFID = 11, /* VF_ID not found */ BFA_STATUS_DATACORRUPTED = 12, /* Diag returned data corrupted */ diff --git a/drivers/scsi/bfa/bfa_fc.h b/drivers/scsi/bfa/bfa_fc.h index 562ef739b0b..64069a0a3d0 100644 --- a/drivers/scsi/bfa/bfa_fc.h +++ b/drivers/scsi/bfa/bfa_fc.h @@ -1026,7 +1026,7 @@ struct fc_alpabm_s { #define FC_ED_TOV 2 #define FC_REC_TOV (FC_ED_TOV + 1) #define FC_RA_TOV 10 -#define FC_ELS_TOV ((2 * FC_RA_TOV) + 1) +#define FC_ELS_TOV (2 * FC_RA_TOV) #define FC_FCCT_TOV (3 * FC_RA_TOV) /* diff --git a/drivers/scsi/bfa/bfa_fcs_lport.c b/drivers/scsi/bfa/bfa_fcs_lport.c index f5e4e61a0fd..ff75ef89175 100644 --- a/drivers/scsi/bfa/bfa_fcs_lport.c +++ b/drivers/scsi/bfa/bfa_fcs_lport.c @@ -773,7 +773,20 @@ bfa_fcs_lport_uf_recv(struct bfa_fcs_lport_s *lport, bfa_trc(lport->fcs, fchs->type); if (!bfa_fcs_lport_is_online(lport)) { - bfa_stats(lport, uf_recv_drops); + /* + * In direct attach topology, it is possible to get a PLOGI + * before the lport is online due to port feature + * (QoS/Trunk/FEC/CR), so send a rjt + */ + if ((fchs->type == FC_TYPE_ELS) && + (els_cmd->els_code == FC_ELS_PLOGI)) { + bfa_fcs_lport_send_ls_rjt(lport, fchs, + FC_LS_RJT_RSN_UNABLE_TO_PERF_CMD, + FC_LS_RJT_EXP_NO_ADDL_INFO); + bfa_stats(lport, plogi_rcvd); + } else + bfa_stats(lport, uf_recv_drops); + return; } diff --git a/drivers/scsi/bfa/bfa_ioc.c b/drivers/scsi/bfa/bfa_ioc.c index f78bcb6696b..65180e15de6 100644 --- a/drivers/scsi/bfa/bfa_ioc.c +++ b/drivers/scsi/bfa/bfa_ioc.c @@ -21,6 +21,7 @@ #include "bfi_reg.h" #include "bfa_defs.h" #include "bfa_defs_svc.h" +#include "bfi.h" BFA_TRC_FILE(CNA, IOC); @@ -45,6 +46,14 @@ BFA_TRC_FILE(CNA, IOC); #define BFA_DBG_FWTRC_OFF(_fn) (BFI_IOC_TRC_OFF + BFA_DBG_FWTRC_LEN * (_fn)) +#define bfa_ioc_state_disabled(__sm) \ + (((__sm) == BFI_IOC_UNINIT) || \ + ((__sm) == BFI_IOC_INITING) || \ + ((__sm) == BFI_IOC_HWINIT) || \ + ((__sm) == BFI_IOC_DISABLED) || \ + ((__sm) == BFI_IOC_FAIL) || \ + ((__sm) == BFI_IOC_CFG_DISABLED)) + /* * Asic specific macros : see bfa_hw_cb.c and bfa_hw_ct.c for details. */ @@ -102,6 +111,12 @@ static void bfa_ioc_disable_comp(struct bfa_ioc_s *ioc); static void bfa_ioc_lpu_stop(struct bfa_ioc_s *ioc); static void bfa_ioc_fail_notify(struct bfa_ioc_s *ioc); static void bfa_ioc_pf_fwmismatch(struct bfa_ioc_s *ioc); +static enum bfi_ioc_img_ver_cmp_e bfa_ioc_fw_ver_patch_cmp( + struct bfi_ioc_image_hdr_s *base_fwhdr, + struct bfi_ioc_image_hdr_s *fwhdr_to_cmp); +static enum bfi_ioc_img_ver_cmp_e bfa_ioc_flash_fwver_cmp( + struct bfa_ioc_s *ioc, + struct bfi_ioc_image_hdr_s *base_fwhdr); /* * IOC state machine definitions/declarations @@ -1454,28 +1469,42 @@ bfa_ioc_fwver_get(struct bfa_ioc_s *ioc, struct bfi_ioc_image_hdr_s *fwhdr) } /* - * Returns TRUE if same. + * Returns TRUE if driver is willing to work with current smem f/w version. */ bfa_boolean_t -bfa_ioc_fwver_cmp(struct bfa_ioc_s *ioc, struct bfi_ioc_image_hdr_s *fwhdr) +bfa_ioc_fwver_cmp(struct bfa_ioc_s *ioc, + struct bfi_ioc_image_hdr_s *smem_fwhdr) { struct bfi_ioc_image_hdr_s *drv_fwhdr; - int i; + enum bfi_ioc_img_ver_cmp_e smem_flash_cmp, drv_smem_cmp; drv_fwhdr = (struct bfi_ioc_image_hdr_s *) bfa_cb_image_get_chunk(bfa_ioc_asic_gen(ioc), 0); - for (i = 0; i < BFI_IOC_MD5SUM_SZ; i++) { - if (fwhdr->md5sum[i] != cpu_to_le32(drv_fwhdr->md5sum[i])) { - bfa_trc(ioc, i); - bfa_trc(ioc, fwhdr->md5sum[i]); - bfa_trc(ioc, drv_fwhdr->md5sum[i]); - return BFA_FALSE; - } + /* + * If smem is incompatible or old, driver should not work with it. + */ + drv_smem_cmp = bfa_ioc_fw_ver_patch_cmp(drv_fwhdr, smem_fwhdr); + if (drv_smem_cmp == BFI_IOC_IMG_VER_INCOMP || + drv_smem_cmp == BFI_IOC_IMG_VER_OLD) { + return BFA_FALSE; } - bfa_trc(ioc, fwhdr->md5sum[0]); - return BFA_TRUE; + /* + * IF Flash has a better F/W than smem do not work with smem. + * If smem f/w == flash f/w, as smem f/w not old | incmp, work with it. + * If Flash is old or incomp work with smem iff smem f/w == drv f/w. + */ + smem_flash_cmp = bfa_ioc_flash_fwver_cmp(ioc, smem_fwhdr); + + if (smem_flash_cmp == BFI_IOC_IMG_VER_BETTER) { + return BFA_FALSE; + } else if (smem_flash_cmp == BFI_IOC_IMG_VER_SAME) { + return BFA_TRUE; + } else { + return (drv_smem_cmp == BFI_IOC_IMG_VER_SAME) ? + BFA_TRUE : BFA_FALSE; + } } /* @@ -1485,17 +1514,9 @@ bfa_ioc_fwver_cmp(struct bfa_ioc_s *ioc, struct bfi_ioc_image_hdr_s *fwhdr) static bfa_boolean_t bfa_ioc_fwver_valid(struct bfa_ioc_s *ioc, u32 boot_env) { - struct bfi_ioc_image_hdr_s fwhdr, *drv_fwhdr; + struct bfi_ioc_image_hdr_s fwhdr; bfa_ioc_fwver_get(ioc, &fwhdr); - drv_fwhdr = (struct bfi_ioc_image_hdr_s *) - bfa_cb_image_get_chunk(bfa_ioc_asic_gen(ioc), 0); - - if (fwhdr.signature != cpu_to_le32(drv_fwhdr->signature)) { - bfa_trc(ioc, fwhdr.signature); - bfa_trc(ioc, drv_fwhdr->signature); - return BFA_FALSE; - } if (swab32(fwhdr.bootenv) != boot_env) { bfa_trc(ioc, fwhdr.bootenv); @@ -1506,6 +1527,168 @@ bfa_ioc_fwver_valid(struct bfa_ioc_s *ioc, u32 boot_env) return bfa_ioc_fwver_cmp(ioc, &fwhdr); } +static bfa_boolean_t +bfa_ioc_fwver_md5_check(struct bfi_ioc_image_hdr_s *fwhdr_1, + struct bfi_ioc_image_hdr_s *fwhdr_2) +{ + int i; + + for (i = 0; i < BFI_IOC_MD5SUM_SZ; i++) + if (fwhdr_1->md5sum[i] != fwhdr_2->md5sum[i]) + return BFA_FALSE; + + return BFA_TRUE; +} + +/* + * Returns TRUE if major minor and maintainence are same. + * If patch versions are same, check for MD5 Checksum to be same. + */ +static bfa_boolean_t +bfa_ioc_fw_ver_compatible(struct bfi_ioc_image_hdr_s *drv_fwhdr, + struct bfi_ioc_image_hdr_s *fwhdr_to_cmp) +{ + if (drv_fwhdr->signature != fwhdr_to_cmp->signature) + return BFA_FALSE; + + if (drv_fwhdr->fwver.major != fwhdr_to_cmp->fwver.major) + return BFA_FALSE; + + if (drv_fwhdr->fwver.minor != fwhdr_to_cmp->fwver.minor) + return BFA_FALSE; + + if (drv_fwhdr->fwver.maint != fwhdr_to_cmp->fwver.maint) + return BFA_FALSE; + + if (drv_fwhdr->fwver.patch == fwhdr_to_cmp->fwver.patch && + drv_fwhdr->fwver.phase == fwhdr_to_cmp->fwver.phase && + drv_fwhdr->fwver.build == fwhdr_to_cmp->fwver.build) { + return bfa_ioc_fwver_md5_check(drv_fwhdr, fwhdr_to_cmp); + } + + return BFA_TRUE; +} + +static bfa_boolean_t +bfa_ioc_flash_fwver_valid(struct bfi_ioc_image_hdr_s *flash_fwhdr) +{ + if (flash_fwhdr->fwver.major == 0 || flash_fwhdr->fwver.major == 0xFF) + return BFA_FALSE; + + return BFA_TRUE; +} + +static bfa_boolean_t fwhdr_is_ga(struct bfi_ioc_image_hdr_s *fwhdr) +{ + if (fwhdr->fwver.phase == 0 && + fwhdr->fwver.build == 0) + return BFA_TRUE; + + return BFA_FALSE; +} + +/* + * Returns TRUE if both are compatible and patch of fwhdr_to_cmp is better. + */ +static enum bfi_ioc_img_ver_cmp_e +bfa_ioc_fw_ver_patch_cmp(struct bfi_ioc_image_hdr_s *base_fwhdr, + struct bfi_ioc_image_hdr_s *fwhdr_to_cmp) +{ + if (bfa_ioc_fw_ver_compatible(base_fwhdr, fwhdr_to_cmp) == BFA_FALSE) + return BFI_IOC_IMG_VER_INCOMP; + + if (fwhdr_to_cmp->fwver.patch > base_fwhdr->fwver.patch) + return BFI_IOC_IMG_VER_BETTER; + + else if (fwhdr_to_cmp->fwver.patch < base_fwhdr->fwver.patch) + return BFI_IOC_IMG_VER_OLD; + + /* + * GA takes priority over internal builds of the same patch stream. + * At this point major minor maint and patch numbers are same. + */ + + if (fwhdr_is_ga(base_fwhdr) == BFA_TRUE) { + if (fwhdr_is_ga(fwhdr_to_cmp)) + return BFI_IOC_IMG_VER_SAME; + else + return BFI_IOC_IMG_VER_OLD; + } else { + if (fwhdr_is_ga(fwhdr_to_cmp)) + return BFI_IOC_IMG_VER_BETTER; + } + + if (fwhdr_to_cmp->fwver.phase > base_fwhdr->fwver.phase) + return BFI_IOC_IMG_VER_BETTER; + else if (fwhdr_to_cmp->fwver.phase < base_fwhdr->fwver.phase) + return BFI_IOC_IMG_VER_OLD; + + if (fwhdr_to_cmp->fwver.build > base_fwhdr->fwver.build) + return BFI_IOC_IMG_VER_BETTER; + else if (fwhdr_to_cmp->fwver.build < base_fwhdr->fwver.build) + return BFI_IOC_IMG_VER_OLD; + + /* + * All Version Numbers are equal. + * Md5 check to be done as a part of compatibility check. + */ + return BFI_IOC_IMG_VER_SAME; +} + +#define BFA_FLASH_PART_FWIMG_ADDR 0x100000 /* fw image address */ + +bfa_status_t +bfa_ioc_flash_img_get_chnk(struct bfa_ioc_s *ioc, u32 off, + u32 *fwimg) +{ + return bfa_flash_raw_read(ioc->pcidev.pci_bar_kva, + BFA_FLASH_PART_FWIMG_ADDR + (off * sizeof(u32)), + (char *)fwimg, BFI_FLASH_CHUNK_SZ); +} + +static enum bfi_ioc_img_ver_cmp_e +bfa_ioc_flash_fwver_cmp(struct bfa_ioc_s *ioc, + struct bfi_ioc_image_hdr_s *base_fwhdr) +{ + struct bfi_ioc_image_hdr_s *flash_fwhdr; + bfa_status_t status; + u32 fwimg[BFI_FLASH_CHUNK_SZ_WORDS]; + + status = bfa_ioc_flash_img_get_chnk(ioc, 0, fwimg); + if (status != BFA_STATUS_OK) + return BFI_IOC_IMG_VER_INCOMP; + + flash_fwhdr = (struct bfi_ioc_image_hdr_s *) fwimg; + if (bfa_ioc_flash_fwver_valid(flash_fwhdr) == BFA_TRUE) + return bfa_ioc_fw_ver_patch_cmp(base_fwhdr, flash_fwhdr); + else + return BFI_IOC_IMG_VER_INCOMP; +} + + +/* + * Invalidate fwver signature + */ +bfa_status_t +bfa_ioc_fwsig_invalidate(struct bfa_ioc_s *ioc) +{ + + u32 pgnum, pgoff; + u32 loff = 0; + enum bfi_ioc_state ioc_fwstate; + + ioc_fwstate = bfa_ioc_get_cur_ioc_fwstate(ioc); + if (!bfa_ioc_state_disabled(ioc_fwstate)) + return BFA_STATUS_ADAPTER_ENABLED; + + pgnum = PSS_SMEM_PGNUM(ioc->ioc_regs.smem_pg0, loff); + pgoff = PSS_SMEM_PGOFF(loff); + writel(pgnum, ioc->ioc_regs.host_page_num_fn); + bfa_mem_write(ioc->ioc_regs.smem_page_start, loff, BFA_IOC_FW_INV_SIGN); + + return BFA_STATUS_OK; +} + /* * Conditionally flush any pending message from firmware at start. */ @@ -1544,8 +1727,8 @@ bfa_ioc_hwinit(struct bfa_ioc_s *ioc, bfa_boolean_t force) BFA_FALSE : bfa_ioc_fwver_valid(ioc, boot_env); if (!fwvalid) { - bfa_ioc_boot(ioc, boot_type, boot_env); - bfa_ioc_poll_fwinit(ioc); + if (bfa_ioc_boot(ioc, boot_type, boot_env) == BFA_STATUS_OK) + bfa_ioc_poll_fwinit(ioc); return; } @@ -1580,8 +1763,8 @@ bfa_ioc_hwinit(struct bfa_ioc_s *ioc, bfa_boolean_t force) /* * Initialize the h/w for any other states. */ - bfa_ioc_boot(ioc, boot_type, boot_env); - bfa_ioc_poll_fwinit(ioc); + if (bfa_ioc_boot(ioc, boot_type, boot_env) == BFA_STATUS_OK) + bfa_ioc_poll_fwinit(ioc); } static void @@ -1684,7 +1867,7 @@ bfa_ioc_hb_monitor(struct bfa_ioc_s *ioc) /* * Initiate a full firmware download. */ -static void +static bfa_status_t bfa_ioc_download_fw(struct bfa_ioc_s *ioc, u32 boot_type, u32 boot_env) { @@ -1694,28 +1877,60 @@ bfa_ioc_download_fw(struct bfa_ioc_s *ioc, u32 boot_type, u32 chunkno = 0; u32 i; u32 asicmode; + u32 fwimg_size; + u32 fwimg_buf[BFI_FLASH_CHUNK_SZ_WORDS]; + bfa_status_t status; + + if (boot_env == BFI_FWBOOT_ENV_OS && + boot_type == BFI_FWBOOT_TYPE_FLASH) { + fwimg_size = BFI_FLASH_IMAGE_SZ/sizeof(u32); + + status = bfa_ioc_flash_img_get_chnk(ioc, + BFA_IOC_FLASH_CHUNK_ADDR(chunkno), fwimg_buf); + if (status != BFA_STATUS_OK) + return status; + + fwimg = fwimg_buf; + } else { + fwimg_size = bfa_cb_image_get_size(bfa_ioc_asic_gen(ioc)); + fwimg = bfa_cb_image_get_chunk(bfa_ioc_asic_gen(ioc), + BFA_IOC_FLASH_CHUNK_ADDR(chunkno)); + } + + bfa_trc(ioc, fwimg_size); - bfa_trc(ioc, bfa_cb_image_get_size(bfa_ioc_asic_gen(ioc))); - fwimg = bfa_cb_image_get_chunk(bfa_ioc_asic_gen(ioc), chunkno); pgnum = PSS_SMEM_PGNUM(ioc->ioc_regs.smem_pg0, loff); pgoff = PSS_SMEM_PGOFF(loff); writel(pgnum, ioc->ioc_regs.host_page_num_fn); - for (i = 0; i < bfa_cb_image_get_size(bfa_ioc_asic_gen(ioc)); i++) { + for (i = 0; i < fwimg_size; i++) { if (BFA_IOC_FLASH_CHUNK_NO(i) != chunkno) { chunkno = BFA_IOC_FLASH_CHUNK_NO(i); - fwimg = bfa_cb_image_get_chunk(bfa_ioc_asic_gen(ioc), + + if (boot_env == BFI_FWBOOT_ENV_OS && + boot_type == BFI_FWBOOT_TYPE_FLASH) { + status = bfa_ioc_flash_img_get_chnk(ioc, + BFA_IOC_FLASH_CHUNK_ADDR(chunkno), + fwimg_buf); + if (status != BFA_STATUS_OK) + return status; + + fwimg = fwimg_buf; + } else { + fwimg = bfa_cb_image_get_chunk( + bfa_ioc_asic_gen(ioc), BFA_IOC_FLASH_CHUNK_ADDR(chunkno)); + } } /* * write smem */ bfa_mem_write(ioc->ioc_regs.smem_page_start, loff, - cpu_to_le32(fwimg[BFA_IOC_FLASH_OFFSET_IN_CHUNK(i)])); + fwimg[BFA_IOC_FLASH_OFFSET_IN_CHUNK(i)]); loff += sizeof(u32); @@ -1733,8 +1948,12 @@ bfa_ioc_download_fw(struct bfa_ioc_s *ioc, u32 boot_type, ioc->ioc_regs.host_page_num_fn); /* - * Set boot type and device mode at the end. + * Set boot type, env and device mode at the end. */ + if (boot_env == BFI_FWBOOT_ENV_OS && + boot_type == BFI_FWBOOT_TYPE_FLASH) { + boot_type = BFI_FWBOOT_TYPE_NORMAL; + } asicmode = BFI_FWBOOT_DEVMODE(ioc->asic_gen, ioc->asic_mode, ioc->port0_mode, ioc->port1_mode); bfa_mem_write(ioc->ioc_regs.smem_page_start, BFI_FWBOOT_DEVMODE_OFF, @@ -1743,6 +1962,7 @@ bfa_ioc_download_fw(struct bfa_ioc_s *ioc, u32 boot_type, swab32(boot_type)); bfa_mem_write(ioc->ioc_regs.smem_page_start, BFI_FWBOOT_ENV_OFF, swab32(boot_env)); + return BFA_STATUS_OK; } @@ -2002,13 +2222,30 @@ bfa_ioc_pll_init(struct bfa_ioc_s *ioc) * Interface used by diag module to do firmware boot with memory test * as the entry vector. */ -void +bfa_status_t bfa_ioc_boot(struct bfa_ioc_s *ioc, u32 boot_type, u32 boot_env) { + struct bfi_ioc_image_hdr_s *drv_fwhdr; + bfa_status_t status; bfa_ioc_stats(ioc, ioc_boots); if (bfa_ioc_pll_init(ioc) != BFA_STATUS_OK) - return; + return BFA_STATUS_FAILED; + + if (boot_env == BFI_FWBOOT_ENV_OS && + boot_type == BFI_FWBOOT_TYPE_NORMAL) { + + drv_fwhdr = (struct bfi_ioc_image_hdr_s *) + bfa_cb_image_get_chunk(bfa_ioc_asic_gen(ioc), 0); + + /* + * Work with Flash iff flash f/w is better than driver f/w. + * Otherwise push drivers firmware. + */ + if (bfa_ioc_flash_fwver_cmp(ioc, drv_fwhdr) == + BFI_IOC_IMG_VER_BETTER) + boot_type = BFI_FWBOOT_TYPE_FLASH; + } /* * Initialize IOC state of all functions on a chip reset. @@ -2022,8 +2259,14 @@ bfa_ioc_boot(struct bfa_ioc_s *ioc, u32 boot_type, u32 boot_env) } bfa_ioc_msgflush(ioc); - bfa_ioc_download_fw(ioc, boot_type, boot_env); - bfa_ioc_lpu_start(ioc); + status = bfa_ioc_download_fw(ioc, boot_type, boot_env); + if (status == BFA_STATUS_OK) + bfa_ioc_lpu_start(ioc); + else { + WARN_ON(boot_type == BFI_FWBOOT_TYPE_MEMTEST); + bfa_iocpf_timeout(ioc); + } + return status; } /* @@ -2419,14 +2662,6 @@ bfa_ioc_fw_mismatch(struct bfa_ioc_s *ioc) bfa_fsm_cmp_state(&ioc->iocpf, bfa_iocpf_sm_mismatch); } -#define bfa_ioc_state_disabled(__sm) \ - (((__sm) == BFI_IOC_UNINIT) || \ - ((__sm) == BFI_IOC_INITING) || \ - ((__sm) == BFI_IOC_HWINIT) || \ - ((__sm) == BFI_IOC_DISABLED) || \ - ((__sm) == BFI_IOC_FAIL) || \ - ((__sm) == BFI_IOC_CFG_DISABLED)) - /* * Check if adapter is disabled -- both IOCs should be in a disabled * state. @@ -6423,3 +6658,407 @@ bfa_fru_intr(void *fruarg, struct bfi_mbmsg_s *msg) WARN_ON(1); } } + +/* + * register definitions + */ +#define FLI_CMD_REG 0x0001d000 +#define FLI_RDDATA_REG 0x0001d010 +#define FLI_ADDR_REG 0x0001d004 +#define FLI_DEV_STATUS_REG 0x0001d014 + +#define BFA_FLASH_FIFO_SIZE 128 /* fifo size */ +#define BFA_FLASH_CHECK_MAX 10000 /* max # of status check */ +#define BFA_FLASH_BLOCKING_OP_MAX 1000000 /* max # of blocking op check */ +#define BFA_FLASH_WIP_MASK 0x01 /* write in progress bit mask */ + +enum bfa_flash_cmd { + BFA_FLASH_FAST_READ = 0x0b, /* fast read */ + BFA_FLASH_READ_STATUS = 0x05, /* read status */ +}; + +/** + * @brief hardware error definition + */ +enum bfa_flash_err { + BFA_FLASH_NOT_PRESENT = -1, /*!< flash not present */ + BFA_FLASH_UNINIT = -2, /*!< flash not initialized */ + BFA_FLASH_BAD = -3, /*!< flash bad */ + BFA_FLASH_BUSY = -4, /*!< flash busy */ + BFA_FLASH_ERR_CMD_ACT = -5, /*!< command active never cleared */ + BFA_FLASH_ERR_FIFO_CNT = -6, /*!< fifo count never cleared */ + BFA_FLASH_ERR_WIP = -7, /*!< write-in-progress never cleared */ + BFA_FLASH_ERR_TIMEOUT = -8, /*!< fli timeout */ + BFA_FLASH_ERR_LEN = -9, /*!< invalid length */ +}; + +/** + * @brief flash command register data structure + */ +union bfa_flash_cmd_reg_u { + struct { +#ifdef __BIG_ENDIAN + u32 act:1; + u32 rsv:1; + u32 write_cnt:9; + u32 read_cnt:9; + u32 addr_cnt:4; + u32 cmd:8; +#else + u32 cmd:8; + u32 addr_cnt:4; + u32 read_cnt:9; + u32 write_cnt:9; + u32 rsv:1; + u32 act:1; +#endif + } r; + u32 i; +}; + +/** + * @brief flash device status register data structure + */ +union bfa_flash_dev_status_reg_u { + struct { +#ifdef __BIG_ENDIAN + u32 rsv:21; + u32 fifo_cnt:6; + u32 busy:1; + u32 init_status:1; + u32 present:1; + u32 bad:1; + u32 good:1; +#else + u32 good:1; + u32 bad:1; + u32 present:1; + u32 init_status:1; + u32 busy:1; + u32 fifo_cnt:6; + u32 rsv:21; +#endif + } r; + u32 i; +}; + +/** + * @brief flash address register data structure + */ +union bfa_flash_addr_reg_u { + struct { +#ifdef __BIG_ENDIAN + u32 addr:24; + u32 dummy:8; +#else + u32 dummy:8; + u32 addr:24; +#endif + } r; + u32 i; +}; + +/** + * dg flash_raw_private Flash raw private functions + */ +static void +bfa_flash_set_cmd(void __iomem *pci_bar, u8 wr_cnt, + u8 rd_cnt, u8 ad_cnt, u8 op) +{ + union bfa_flash_cmd_reg_u cmd; + + cmd.i = 0; + cmd.r.act = 1; + cmd.r.write_cnt = wr_cnt; + cmd.r.read_cnt = rd_cnt; + cmd.r.addr_cnt = ad_cnt; + cmd.r.cmd = op; + writel(cmd.i, (pci_bar + FLI_CMD_REG)); +} + +static void +bfa_flash_set_addr(void __iomem *pci_bar, u32 address) +{ + union bfa_flash_addr_reg_u addr; + + addr.r.addr = address & 0x00ffffff; + addr.r.dummy = 0; + writel(addr.i, (pci_bar + FLI_ADDR_REG)); +} + +static int +bfa_flash_cmd_act_check(void __iomem *pci_bar) +{ + union bfa_flash_cmd_reg_u cmd; + + cmd.i = readl(pci_bar + FLI_CMD_REG); + + if (cmd.r.act) + return BFA_FLASH_ERR_CMD_ACT; + + return 0; +} + +/** + * @brief + * Flush FLI data fifo. + * + * @param[in] pci_bar - pci bar address + * @param[in] dev_status - device status + * + * Return 0 on success, negative error number on error. + */ +static u32 +bfa_flash_fifo_flush(void __iomem *pci_bar) +{ + u32 i; + u32 t; + union bfa_flash_dev_status_reg_u dev_status; + + dev_status.i = readl(pci_bar + FLI_DEV_STATUS_REG); + + if (!dev_status.r.fifo_cnt) + return 0; + + /* fifo counter in terms of words */ + for (i = 0; i < dev_status.r.fifo_cnt; i++) + t = readl(pci_bar + FLI_RDDATA_REG); + + /* + * Check the device status. It may take some time. + */ + for (i = 0; i < BFA_FLASH_CHECK_MAX; i++) { + dev_status.i = readl(pci_bar + FLI_DEV_STATUS_REG); + if (!dev_status.r.fifo_cnt) + break; + } + + if (dev_status.r.fifo_cnt) + return BFA_FLASH_ERR_FIFO_CNT; + + return 0; +} + +/** + * @brief + * Read flash status. + * + * @param[in] pci_bar - pci bar address + * + * Return 0 on success, negative error number on error. +*/ +static u32 +bfa_flash_status_read(void __iomem *pci_bar) +{ + union bfa_flash_dev_status_reg_u dev_status; + u32 status; + u32 ret_status; + int i; + + status = bfa_flash_fifo_flush(pci_bar); + if (status < 0) + return status; + + bfa_flash_set_cmd(pci_bar, 0, 4, 0, BFA_FLASH_READ_STATUS); + + for (i = 0; i < BFA_FLASH_CHECK_MAX; i++) { + status = bfa_flash_cmd_act_check(pci_bar); + if (!status) + break; + } + + if (status) + return status; + + dev_status.i = readl(pci_bar + FLI_DEV_STATUS_REG); + if (!dev_status.r.fifo_cnt) + return BFA_FLASH_BUSY; + + ret_status = readl(pci_bar + FLI_RDDATA_REG); + ret_status >>= 24; + + status = bfa_flash_fifo_flush(pci_bar); + if (status < 0) + return status; + + return ret_status; +} + +/** + * @brief + * Start flash read operation. + * + * @param[in] pci_bar - pci bar address + * @param[in] offset - flash address offset + * @param[in] len - read data length + * @param[in] buf - read data buffer + * + * Return 0 on success, negative error number on error. + */ +static u32 +bfa_flash_read_start(void __iomem *pci_bar, u32 offset, u32 len, + char *buf) +{ + u32 status; + + /* + * len must be mutiple of 4 and not exceeding fifo size + */ + if (len == 0 || len > BFA_FLASH_FIFO_SIZE || (len & 0x03) != 0) + return BFA_FLASH_ERR_LEN; + + /* + * check status + */ + status = bfa_flash_status_read(pci_bar); + if (status == BFA_FLASH_BUSY) + status = bfa_flash_status_read(pci_bar); + + if (status < 0) + return status; + + /* + * check if write-in-progress bit is cleared + */ + if (status & BFA_FLASH_WIP_MASK) + return BFA_FLASH_ERR_WIP; + + bfa_flash_set_addr(pci_bar, offset); + + bfa_flash_set_cmd(pci_bar, 0, (u8)len, 4, BFA_FLASH_FAST_READ); + + return 0; +} + +/** + * @brief + * Check flash read operation. + * + * @param[in] pci_bar - pci bar address + * + * Return flash device status, 1 if busy, 0 if not. + */ +static u32 +bfa_flash_read_check(void __iomem *pci_bar) +{ + if (bfa_flash_cmd_act_check(pci_bar)) + return 1; + + return 0; +} +/** + * @brief + * End flash read operation. + * + * @param[in] pci_bar - pci bar address + * @param[in] len - read data length + * @param[in] buf - read data buffer + * + */ +static void +bfa_flash_read_end(void __iomem *pci_bar, u32 len, char *buf) +{ + + u32 i; + + /* + * read data fifo up to 32 words + */ + for (i = 0; i < len; i += 4) { + u32 w = readl(pci_bar + FLI_RDDATA_REG); + *((u32 *) (buf + i)) = swab32(w); + } + + bfa_flash_fifo_flush(pci_bar); +} + +/** + * @brief + * Perform flash raw read. + * + * @param[in] pci_bar - pci bar address + * @param[in] offset - flash partition address offset + * @param[in] buf - read data buffer + * @param[in] len - read data length + * + * Return status. + */ + + +#define FLASH_BLOCKING_OP_MAX 500 +#define FLASH_SEM_LOCK_REG 0x18820 + +static int +bfa_raw_sem_get(void __iomem *bar) +{ + int locked; + + locked = readl((bar + FLASH_SEM_LOCK_REG)); + return !locked; + +} + +bfa_status_t +bfa_flash_sem_get(void __iomem *bar) +{ + u32 n = FLASH_BLOCKING_OP_MAX; + + while (!bfa_raw_sem_get(bar)) { + if (--n <= 0) + return BFA_STATUS_BADFLASH; + udelay(10000); + } + return BFA_STATUS_OK; +} + +void +bfa_flash_sem_put(void __iomem *bar) +{ + writel(0, (bar + FLASH_SEM_LOCK_REG)); +} + +bfa_status_t +bfa_flash_raw_read(void __iomem *pci_bar, u32 offset, char *buf, + u32 len) +{ + u32 n, status; + u32 off, l, s, residue, fifo_sz; + + residue = len; + off = 0; + fifo_sz = BFA_FLASH_FIFO_SIZE; + status = bfa_flash_sem_get(pci_bar); + if (status != BFA_STATUS_OK) + return status; + + while (residue) { + s = offset + off; + n = s / fifo_sz; + l = (n + 1) * fifo_sz - s; + if (l > residue) + l = residue; + + status = bfa_flash_read_start(pci_bar, offset + off, l, + &buf[off]); + if (status < 0) { + bfa_flash_sem_put(pci_bar); + return BFA_STATUS_FAILED; + } + + n = BFA_FLASH_BLOCKING_OP_MAX; + while (bfa_flash_read_check(pci_bar)) { + if (--n <= 0) { + bfa_flash_sem_put(pci_bar); + return BFA_STATUS_FAILED; + } + } + + bfa_flash_read_end(pci_bar, l, &buf[off]); + + residue -= l; + off += l; + } + bfa_flash_sem_put(pci_bar); + + return BFA_STATUS_OK; +} diff --git a/drivers/scsi/bfa/bfa_ioc.h b/drivers/scsi/bfa/bfa_ioc.h index 90814fe85ac..2e28392c2fb 100644 --- a/drivers/scsi/bfa/bfa_ioc.h +++ b/drivers/scsi/bfa/bfa_ioc.h @@ -515,6 +515,8 @@ void bfa_flash_attach(struct bfa_flash_s *flash, struct bfa_ioc_s *ioc, void *dev, struct bfa_trc_mod_s *trcmod, bfa_boolean_t mincfg); void bfa_flash_memclaim(struct bfa_flash_s *flash, u8 *dm_kva, u64 dm_pa, bfa_boolean_t mincfg); +bfa_status_t bfa_flash_raw_read(void __iomem *pci_bar_kva, + u32 offset, char *buf, u32 len); /* * DIAG module specific @@ -888,7 +890,7 @@ void bfa_ioc_enable(struct bfa_ioc_s *ioc); void bfa_ioc_disable(struct bfa_ioc_s *ioc); bfa_boolean_t bfa_ioc_intx_claim(struct bfa_ioc_s *ioc); -void bfa_ioc_boot(struct bfa_ioc_s *ioc, u32 boot_type, +bfa_status_t bfa_ioc_boot(struct bfa_ioc_s *ioc, u32 boot_type, u32 boot_env); void bfa_ioc_isr(struct bfa_ioc_s *ioc, struct bfi_mbmsg_s *msg); void bfa_ioc_error_isr(struct bfa_ioc_s *ioc); @@ -919,6 +921,7 @@ bfa_status_t bfa_ioc_debug_fwtrc(struct bfa_ioc_s *ioc, void *trcdata, int *trclen); bfa_status_t bfa_ioc_debug_fwcore(struct bfa_ioc_s *ioc, void *buf, u32 *offset, int *buflen); +bfa_status_t bfa_ioc_fwsig_invalidate(struct bfa_ioc_s *ioc); bfa_boolean_t bfa_ioc_sem_get(void __iomem *sem_reg); void bfa_ioc_fwver_get(struct bfa_ioc_s *ioc, struct bfi_ioc_image_hdr_s *fwhdr); @@ -956,6 +959,8 @@ bfa_status_t bfa_ablk_optrom_en(struct bfa_ablk_s *ablk, bfa_status_t bfa_ablk_optrom_dis(struct bfa_ablk_s *ablk, bfa_ablk_cbfn_t cbfn, void *cbarg); +bfa_status_t bfa_ioc_flash_img_get_chnk(struct bfa_ioc_s *ioc, u32 off, + u32 *fwimg); /* * bfa mfg wwn API functions */ diff --git a/drivers/scsi/bfa/bfa_ioc_cb.c b/drivers/scsi/bfa/bfa_ioc_cb.c index e3b92874667..453c2f5b556 100644 --- a/drivers/scsi/bfa/bfa_ioc_cb.c +++ b/drivers/scsi/bfa/bfa_ioc_cb.c @@ -81,6 +81,29 @@ bfa_ioc_set_cb_hwif(struct bfa_ioc_s *ioc) static bfa_boolean_t bfa_ioc_cb_firmware_lock(struct bfa_ioc_s *ioc) { + enum bfi_ioc_state alt_fwstate, cur_fwstate; + struct bfi_ioc_image_hdr_s fwhdr; + + cur_fwstate = bfa_ioc_cb_get_cur_ioc_fwstate(ioc); + bfa_trc(ioc, cur_fwstate); + alt_fwstate = bfa_ioc_cb_get_alt_ioc_fwstate(ioc); + bfa_trc(ioc, alt_fwstate); + + /* + * Uninit implies this is the only driver as of now. + */ + if (cur_fwstate == BFI_IOC_UNINIT) + return BFA_TRUE; + /* + * Check if another driver with a different firmware is active + */ + bfa_ioc_fwver_get(ioc, &fwhdr); + if (!bfa_ioc_fwver_cmp(ioc, &fwhdr) && + alt_fwstate != BFI_IOC_DISABLED) { + bfa_trc(ioc, alt_fwstate); + return BFA_FALSE; + } + return BFA_TRUE; } diff --git a/drivers/scsi/bfa/bfa_svc.c b/drivers/scsi/bfa/bfa_svc.c index 6c41e57fd75..625225f3108 100644 --- a/drivers/scsi/bfa/bfa_svc.c +++ b/drivers/scsi/bfa/bfa_svc.c @@ -6758,7 +6758,7 @@ bfa_dport_scn(struct bfa_dport_s *dport, struct bfi_diag_dport_scn_s *msg) dport->rp_pwwn = msg->info.teststart.pwwn; dport->rp_nwwn = msg->info.teststart.nwwn; dport->lpcnt = cpu_to_be32(msg->info.teststart.numfrm); - bfa_dport_result_start(dport, BFA_DPORT_OPMODE_AUTO); + bfa_dport_result_start(dport, msg->info.teststart.mode); break; case BFI_DPORT_SCN_SUBTESTSTART: diff --git a/drivers/scsi/bfa/bfad.c b/drivers/scsi/bfa/bfad.c index fc80a325a1e..cc0fbcdc519 100644 --- a/drivers/scsi/bfa/bfad.c +++ b/drivers/scsi/bfa/bfad.c @@ -63,9 +63,9 @@ int max_rport_logins = BFA_FCS_MAX_RPORT_LOGINS; u32 bfi_image_cb_size, bfi_image_ct_size, bfi_image_ct2_size; u32 *bfi_image_cb, *bfi_image_ct, *bfi_image_ct2; -#define BFAD_FW_FILE_CB "cbfw-3.2.1.1.bin" -#define BFAD_FW_FILE_CT "ctfw-3.2.1.1.bin" -#define BFAD_FW_FILE_CT2 "ct2fw-3.2.1.1.bin" +#define BFAD_FW_FILE_CB "cbfw-3.2.3.0.bin" +#define BFAD_FW_FILE_CT "ctfw-3.2.3.0.bin" +#define BFAD_FW_FILE_CT2 "ct2fw-3.2.3.0.bin" static u32 *bfad_load_fwimg(struct pci_dev *pdev); static void bfad_free_fwimg(void); @@ -204,6 +204,7 @@ static void bfad_sm_created(struct bfad_s *bfad, enum bfad_sm_event event) { unsigned long flags; + bfa_status_t ret; bfa_trc(bfad, event); @@ -217,7 +218,7 @@ bfad_sm_created(struct bfad_s *bfad, enum bfad_sm_event event) if (bfad_setup_intr(bfad)) { printk(KERN_WARNING "bfad%d: bfad_setup_intr failed\n", bfad->inst_no); - bfa_sm_send_event(bfad, BFAD_E_INTR_INIT_FAILED); + bfa_sm_send_event(bfad, BFAD_E_INIT_FAILED); break; } @@ -242,8 +243,26 @@ bfad_sm_created(struct bfad_s *bfad, enum bfad_sm_event event) printk(KERN_WARNING "bfa %s: bfa init failed\n", bfad->pci_name); + spin_lock_irqsave(&bfad->bfad_lock, flags); + bfa_fcs_init(&bfad->bfa_fcs); + spin_unlock_irqrestore(&bfad->bfad_lock, flags); + + ret = bfad_cfg_pport(bfad, BFA_LPORT_ROLE_FCP_IM); + if (ret != BFA_STATUS_OK) { + init_completion(&bfad->comp); + + spin_lock_irqsave(&bfad->bfad_lock, flags); + bfad->pport.flags |= BFAD_PORT_DELETE; + bfa_fcs_exit(&bfad->bfa_fcs); + spin_unlock_irqrestore(&bfad->bfad_lock, flags); + + wait_for_completion(&bfad->comp); + + bfa_sm_send_event(bfad, BFAD_E_INIT_FAILED); + break; + } bfad->bfad_flags |= BFAD_HAL_INIT_FAIL; - bfa_sm_send_event(bfad, BFAD_E_INIT_FAILED); + bfa_sm_send_event(bfad, BFAD_E_HAL_INIT_FAILED); } break; @@ -273,12 +292,14 @@ bfad_sm_initializing(struct bfad_s *bfad, enum bfad_sm_event event) spin_unlock_irqrestore(&bfad->bfad_lock, flags); retval = bfad_start_ops(bfad); - if (retval != BFA_STATUS_OK) + if (retval != BFA_STATUS_OK) { + bfa_sm_set_state(bfad, bfad_sm_failed); break; + } bfa_sm_set_state(bfad, bfad_sm_operational); break; - case BFAD_E_INTR_INIT_FAILED: + case BFAD_E_INIT_FAILED: bfa_sm_set_state(bfad, bfad_sm_uninit); kthread_stop(bfad->bfad_tsk); spin_lock_irqsave(&bfad->bfad_lock, flags); @@ -286,7 +307,7 @@ bfad_sm_initializing(struct bfad_s *bfad, enum bfad_sm_event event) spin_unlock_irqrestore(&bfad->bfad_lock, flags); break; - case BFAD_E_INIT_FAILED: + case BFAD_E_HAL_INIT_FAILED: bfa_sm_set_state(bfad, bfad_sm_failed); break; default: @@ -310,13 +331,8 @@ bfad_sm_failed(struct bfad_s *bfad, enum bfad_sm_event event) break; case BFAD_E_STOP: - if (bfad->bfad_flags & BFAD_CFG_PPORT_DONE) - bfad_uncfg_pport(bfad); - if (bfad->bfad_flags & BFAD_FC4_PROBE_DONE) { - bfad_im_probe_undo(bfad); - bfad->bfad_flags &= ~BFAD_FC4_PROBE_DONE; - } - bfad_stop(bfad); + bfa_sm_set_state(bfad, bfad_sm_fcs_exit); + bfa_sm_send_event(bfad, BFAD_E_FCS_EXIT_COMP); break; case BFAD_E_EXIT_COMP: @@ -824,7 +840,7 @@ bfad_drv_init(struct bfad_s *bfad) printk(KERN_WARNING "Not enough memory to attach all Brocade HBA ports, %s", "System may need more memory.\n"); - goto out_hal_mem_alloc_failure; + return BFA_STATUS_FAILED; } bfad->bfa.trcmod = bfad->trcmod; @@ -841,31 +857,11 @@ bfad_drv_init(struct bfad_s *bfad) bfad->bfa_fcs.trcmod = bfad->trcmod; bfa_fcs_attach(&bfad->bfa_fcs, &bfad->bfa, bfad, BFA_FALSE); bfad->bfa_fcs.fdmi_enabled = fdmi_enable; - bfa_fcs_init(&bfad->bfa_fcs); spin_unlock_irqrestore(&bfad->bfad_lock, flags); bfad->bfad_flags |= BFAD_DRV_INIT_DONE; - /* configure base port */ - rc = bfad_cfg_pport(bfad, BFA_LPORT_ROLE_FCP_IM); - if (rc != BFA_STATUS_OK) - goto out_cfg_pport_fail; - return BFA_STATUS_OK; - -out_cfg_pport_fail: - /* fcs exit - on cfg pport failure */ - spin_lock_irqsave(&bfad->bfad_lock, flags); - init_completion(&bfad->comp); - bfad->pport.flags |= BFAD_PORT_DELETE; - bfa_fcs_exit(&bfad->bfa_fcs); - spin_unlock_irqrestore(&bfad->bfad_lock, flags); - wait_for_completion(&bfad->comp); - /* bfa detach - free hal memory */ - bfa_detach(&bfad->bfa); - bfad_hal_mem_release(bfad); -out_hal_mem_alloc_failure: - return BFA_STATUS_FAILED; } void @@ -1009,13 +1005,19 @@ bfad_start_ops(struct bfad_s *bfad) { /* FCS driver info init */ spin_lock_irqsave(&bfad->bfad_lock, flags); bfa_fcs_driver_info_init(&bfad->bfa_fcs, &driver_info); + + if (bfad->bfad_flags & BFAD_CFG_PPORT_DONE) + bfa_fcs_update_cfg(&bfad->bfa_fcs); + else + bfa_fcs_init(&bfad->bfa_fcs); + spin_unlock_irqrestore(&bfad->bfad_lock, flags); - /* - * FCS update cfg - reset the pwwn/nwwn of fabric base logical port - * with values learned during bfa_init firmware GETATTR REQ. - */ - bfa_fcs_update_cfg(&bfad->bfa_fcs); + if (!(bfad->bfad_flags & BFAD_CFG_PPORT_DONE)) { + retval = bfad_cfg_pport(bfad, BFA_LPORT_ROLE_FCP_IM); + if (retval != BFA_STATUS_OK) + return BFA_STATUS_FAILED; + } /* Setup fc host fixed attribute if the lk supports */ bfad_fc_host_init(bfad->pport.im_port); @@ -1026,10 +1028,6 @@ bfad_start_ops(struct bfad_s *bfad) { printk(KERN_WARNING "bfad_im_probe failed\n"); if (bfa_sm_cmp_state(bfad, bfad_sm_initializing)) bfa_sm_set_state(bfad, bfad_sm_failed); - bfad_im_probe_undo(bfad); - bfad->bfad_flags &= ~BFAD_FC4_PROBE_DONE; - bfad_uncfg_pport(bfad); - bfad_stop(bfad); return BFA_STATUS_FAILED; } else bfad->bfad_flags |= BFAD_FC4_PROBE_DONE; @@ -1399,7 +1397,6 @@ bfad_pci_probe(struct pci_dev *pdev, const struct pci_device_id *pid) return 0; out_bfad_sm_failure: - bfa_detach(&bfad->bfa); bfad_hal_mem_release(bfad); out_drv_init_failure: /* Remove the debugfs node for this bfad */ @@ -1534,7 +1531,7 @@ restart_bfa(struct bfad_s *bfad) if (bfad_setup_intr(bfad)) { dev_printk(KERN_WARNING, &pdev->dev, "%s: bfad_setup_intr failed\n", bfad->pci_name); - bfa_sm_send_event(bfad, BFAD_E_INTR_INIT_FAILED); + bfa_sm_send_event(bfad, BFAD_E_INIT_FAILED); return -1; } @@ -1802,7 +1799,7 @@ out: static u32 * bfad_load_fwimg(struct pci_dev *pdev) { - if (pdev->device == BFA_PCI_DEVICE_ID_CT2) { + if (bfa_asic_id_ct2(pdev->device)) { if (bfi_image_ct2_size == 0) bfad_read_firmware(pdev, &bfi_image_ct2, &bfi_image_ct2_size, BFAD_FW_FILE_CT2); @@ -1812,12 +1809,14 @@ bfad_load_fwimg(struct pci_dev *pdev) bfad_read_firmware(pdev, &bfi_image_ct, &bfi_image_ct_size, BFAD_FW_FILE_CT); return bfi_image_ct; - } else { + } else if (bfa_asic_id_cb(pdev->device)) { if (bfi_image_cb_size == 0) bfad_read_firmware(pdev, &bfi_image_cb, &bfi_image_cb_size, BFAD_FW_FILE_CB); return bfi_image_cb; } + + return NULL; } static void diff --git a/drivers/scsi/bfa/bfad_bsg.c b/drivers/scsi/bfa/bfad_bsg.c index 0467c349251..157f6044a9b 100644 --- a/drivers/scsi/bfa/bfad_bsg.c +++ b/drivers/scsi/bfa/bfad_bsg.c @@ -229,6 +229,18 @@ bfad_iocmd_iocfc_get_attr(struct bfad_s *bfad, void *cmd) } int +bfad_iocmd_ioc_fw_sig_inv(struct bfad_s *bfad, void *cmd) +{ + struct bfa_bsg_gen_s *iocmd = (struct bfa_bsg_gen_s *)cmd; + unsigned long flags; + + spin_lock_irqsave(&bfad->bfad_lock, flags); + iocmd->status = bfa_ioc_fwsig_invalidate(&bfad->bfa.ioc); + spin_unlock_irqrestore(&bfad->bfad_lock, flags); + return 0; +} + +int bfad_iocmd_iocfc_set_intr(struct bfad_s *bfad, void *cmd) { struct bfa_bsg_iocfc_intr_s *iocmd = (struct bfa_bsg_iocfc_intr_s *)cmd; @@ -2893,6 +2905,9 @@ bfad_iocmd_handler(struct bfad_s *bfad, unsigned int cmd, void *iocmd, case IOCMD_IOC_PCIFN_CFG: rc = bfad_iocmd_ioc_get_pcifn_cfg(bfad, iocmd); break; + case IOCMD_IOC_FW_SIG_INV: + rc = bfad_iocmd_ioc_fw_sig_inv(bfad, iocmd); + break; case IOCMD_PCIFN_CREATE: rc = bfad_iocmd_pcifn_create(bfad, iocmd); break; diff --git a/drivers/scsi/bfa/bfad_bsg.h b/drivers/scsi/bfa/bfad_bsg.h index 05f0fc9cf06..90abef69158 100644 --- a/drivers/scsi/bfa/bfad_bsg.h +++ b/drivers/scsi/bfa/bfad_bsg.h @@ -34,6 +34,7 @@ enum { IOCMD_IOC_RESET_FWSTATS, IOCMD_IOC_SET_ADAPTER_NAME, IOCMD_IOC_SET_PORT_NAME, + IOCMD_IOC_FW_SIG_INV, IOCMD_IOCFC_GET_ATTR, IOCMD_IOCFC_SET_INTR, IOCMD_PORT_ENABLE, diff --git a/drivers/scsi/bfa/bfad_drv.h b/drivers/scsi/bfa/bfad_drv.h index 78d3401bc16..8b97877d42c 100644 --- a/drivers/scsi/bfa/bfad_drv.h +++ b/drivers/scsi/bfa/bfad_drv.h @@ -57,7 +57,7 @@ #ifdef BFA_DRIVER_VERSION #define BFAD_DRIVER_VERSION BFA_DRIVER_VERSION #else -#define BFAD_DRIVER_VERSION "3.2.21.1" +#define BFAD_DRIVER_VERSION "3.2.23.0" #endif #define BFAD_PROTO_NAME FCPI_NAME @@ -240,8 +240,8 @@ enum bfad_sm_event { BFAD_E_KTHREAD_CREATE_FAILED = 2, BFAD_E_INIT = 3, BFAD_E_INIT_SUCCESS = 4, - BFAD_E_INIT_FAILED = 5, - BFAD_E_INTR_INIT_FAILED = 6, + BFAD_E_HAL_INIT_FAILED = 5, + BFAD_E_INIT_FAILED = 6, BFAD_E_FCS_EXIT_COMP = 7, BFAD_E_EXIT_COMP = 8, BFAD_E_STOP = 9 diff --git a/drivers/scsi/bfa/bfi.h b/drivers/scsi/bfa/bfi.h index 37bd2564e83..9ef91f907de 100644 --- a/drivers/scsi/bfa/bfi.h +++ b/drivers/scsi/bfa/bfi.h @@ -46,6 +46,7 @@ */ #define BFI_FLASH_CHUNK_SZ 256 /* Flash chunk size */ #define BFI_FLASH_CHUNK_SZ_WORDS (BFI_FLASH_CHUNK_SZ/sizeof(u32)) +#define BFI_FLASH_IMAGE_SZ 0x100000 /* * Msg header common to all msgs @@ -324,7 +325,29 @@ struct bfi_ioc_getattr_reply_s { #define BFI_IOC_TRC_ENTS 256 #define BFI_IOC_FW_SIGNATURE (0xbfadbfad) +#define BFA_IOC_FW_INV_SIGN (0xdeaddead) #define BFI_IOC_MD5SUM_SZ 4 + +struct bfi_ioc_fwver_s { +#ifdef __BIG_ENDIAN + uint8_t patch; + uint8_t maint; + uint8_t minor; + uint8_t major; + uint8_t rsvd[2]; + uint8_t build; + uint8_t phase; +#else + uint8_t major; + uint8_t minor; + uint8_t maint; + uint8_t patch; + uint8_t phase; + uint8_t build; + uint8_t rsvd[2]; +#endif +}; + struct bfi_ioc_image_hdr_s { u32 signature; /* constant signature */ u8 asic_gen; /* asic generation */ @@ -333,10 +356,18 @@ struct bfi_ioc_image_hdr_s { u8 port1_mode; /* device mode for port 1 */ u32 exec; /* exec vector */ u32 bootenv; /* fimware boot env */ - u32 rsvd_b[4]; + u32 rsvd_b[2]; + struct bfi_ioc_fwver_s fwver; u32 md5sum[BFI_IOC_MD5SUM_SZ]; }; +enum bfi_ioc_img_ver_cmp_e { + BFI_IOC_IMG_VER_INCOMP, + BFI_IOC_IMG_VER_OLD, + BFI_IOC_IMG_VER_SAME, + BFI_IOC_IMG_VER_BETTER +}; + #define BFI_FWBOOT_DEVMODE_OFF 4 #define BFI_FWBOOT_TYPE_OFF 8 #define BFI_FWBOOT_ENV_OFF 12 @@ -346,6 +377,12 @@ struct bfi_ioc_image_hdr_s { ((u32)(__p0_mode)) << 8 | \ ((u32)(__p1_mode))) +enum bfi_fwboot_type { + BFI_FWBOOT_TYPE_NORMAL = 0, + BFI_FWBOOT_TYPE_FLASH = 1, + BFI_FWBOOT_TYPE_MEMTEST = 2, +}; + #define BFI_FWBOOT_TYPE_NORMAL 0 #define BFI_FWBOOT_TYPE_MEMTEST 2 #define BFI_FWBOOT_ENV_OS 0 @@ -1107,7 +1144,8 @@ struct bfi_diag_dport_scn_teststart_s { wwn_t pwwn; /* switch port wwn. 8 bytes */ wwn_t nwwn; /* switch node wwn. 8 bytes */ u8 type; /* bfa_diag_dport_test_type_e */ - u8 rsvd[3]; + u8 mode; /* bfa_diag_dport_test_opmode */ + u8 rsvd[2]; u32 numfrm; /* from switch uint in 1M */ }; diff --git a/drivers/scsi/gvp11.c b/drivers/scsi/gvp11.c index 2203ac28110..3b6f83ffddc 100644 --- a/drivers/scsi/gvp11.c +++ b/drivers/scsi/gvp11.c @@ -310,7 +310,7 @@ static int gvp11_probe(struct zorro_dev *z, const struct zorro_device_id *ent) if (!request_mem_region(address, 256, "wd33c93")) return -EBUSY; - regs = (struct gvp11_scsiregs *)(ZTWO_VADDR(address)); + regs = ZTWO_VADDR(address); error = check_wd33c93(regs); if (error) diff --git a/drivers/scsi/hosts.c b/drivers/scsi/hosts.c index f2c5005f312..f28ea070d3d 100644 --- a/drivers/scsi/hosts.c +++ b/drivers/scsi/hosts.c @@ -169,6 +169,7 @@ void scsi_remove_host(struct Scsi_Host *shost) spin_unlock_irqrestore(shost->host_lock, flags); scsi_autopm_get_host(shost); + flush_workqueue(shost->tmf_work_q); scsi_forget_host(shost); mutex_unlock(&shost->scan_mutex); scsi_proc_host_rm(shost); @@ -294,6 +295,8 @@ static void scsi_host_dev_release(struct device *dev) scsi_proc_hostdir_rm(shost->hostt); + if (shost->tmf_work_q) + destroy_workqueue(shost->tmf_work_q); if (shost->ehandler) kthread_stop(shost->ehandler); if (shost->work_q) @@ -316,11 +319,11 @@ static void scsi_host_dev_release(struct device *dev) kfree(shost); } -static unsigned int shost_eh_deadline; +static int shost_eh_deadline = -1; -module_param_named(eh_deadline, shost_eh_deadline, uint, S_IRUGO|S_IWUSR); +module_param_named(eh_deadline, shost_eh_deadline, int, S_IRUGO|S_IWUSR); MODULE_PARM_DESC(eh_deadline, - "SCSI EH timeout in seconds (should be between 1 and 2^32-1)"); + "SCSI EH timeout in seconds (should be between 0 and 2^31-1)"); static struct device_type scsi_host_type = { .name = "scsi_host", @@ -360,7 +363,6 @@ struct Scsi_Host *scsi_host_alloc(struct scsi_host_template *sht, int privsize) INIT_LIST_HEAD(&shost->eh_cmd_q); INIT_LIST_HEAD(&shost->starved_list); init_waitqueue_head(&shost->host_wait); - mutex_init(&shost->scan_mutex); /* @@ -394,9 +396,18 @@ struct Scsi_Host *scsi_host_alloc(struct scsi_host_template *sht, int privsize) shost->unchecked_isa_dma = sht->unchecked_isa_dma; shost->use_clustering = sht->use_clustering; shost->ordered_tag = sht->ordered_tag; - shost->eh_deadline = shost_eh_deadline * HZ; shost->no_write_same = sht->no_write_same; + if (shost_eh_deadline == -1) + shost->eh_deadline = -1; + else if ((ulong) shost_eh_deadline * HZ > INT_MAX) { + shost_printk(KERN_WARNING, shost, + "eh_deadline %u too large, setting to %u\n", + shost_eh_deadline, INT_MAX / HZ); + shost->eh_deadline = INT_MAX; + } else + shost->eh_deadline = shost_eh_deadline * HZ; + if (sht->supported_mode == MODE_UNKNOWN) /* means we didn't set it ... default to INITIATOR */ shost->active_mode = MODE_INITIATOR; @@ -444,9 +455,19 @@ struct Scsi_Host *scsi_host_alloc(struct scsi_host_template *sht, int privsize) goto fail_kfree; } + shost->tmf_work_q = alloc_workqueue("scsi_tmf_%d", + WQ_UNBOUND | WQ_MEM_RECLAIM, + 1, shost->host_no); + if (!shost->tmf_work_q) { + printk(KERN_WARNING "scsi%d: failed to create tmf workq\n", + shost->host_no); + goto fail_kthread; + } scsi_proc_hostdir_add(shost->hostt); return shost; + fail_kthread: + kthread_stop(shost->ehandler); fail_kfree: kfree(shost); return NULL; diff --git a/drivers/scsi/hpsa.c b/drivers/scsi/hpsa.c index 20a5e6ecf94..868318a7067 100644 --- a/drivers/scsi/hpsa.c +++ b/drivers/scsi/hpsa.c @@ -29,7 +29,6 @@ #include <linux/delay.h> #include <linux/fs.h> #include <linux/timer.h> -#include <linux/seq_file.h> #include <linux/init.h> #include <linux/spinlock.h> #include <linux/compat.h> @@ -96,7 +95,6 @@ static const struct pci_device_id hpsa_pci_device_id[] = { {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3351}, {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3352}, {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3353}, - {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x334D}, {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3354}, {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3355}, {PCI_VENDOR_ID_HP, PCI_DEVICE_ID_HP_CISSF, 0x103C, 0x3356}, @@ -143,7 +141,6 @@ static struct board_type products[] = { {0x3351103C, "Smart Array P420", &SA5_access}, {0x3352103C, "Smart Array P421", &SA5_access}, {0x3353103C, "Smart Array P822", &SA5_access}, - {0x334D103C, "Smart Array P822se", &SA5_access}, {0x3354103C, "Smart Array P420i", &SA5_access}, {0x3355103C, "Smart Array P220i", &SA5_access}, {0x3356103C, "Smart Array P721m", &SA5_access}, @@ -171,10 +168,6 @@ static struct board_type products[] = { static int number_of_controllers; -static struct list_head hpsa_ctlr_list = LIST_HEAD_INIT(hpsa_ctlr_list); -static spinlock_t lockup_detector_lock; -static struct task_struct *hpsa_lockup_detector; - static irqreturn_t do_hpsa_intr_intx(int irq, void *dev_id); static irqreturn_t do_hpsa_intr_msi(int irq, void *dev_id); static int hpsa_ioctl(struct scsi_device *dev, int cmd, void *arg); @@ -1248,10 +1241,8 @@ static void complete_scsi_command(struct CommandList *cp) } if (ei->ScsiStatus == SAM_STAT_CHECK_CONDITION) { - if (check_for_unit_attention(h, cp)) { - cmd->result = DID_SOFT_ERROR << 16; + if (check_for_unit_attention(h, cp)) break; - } if (sense_key == ILLEGAL_REQUEST) { /* * SCSI REPORT_LUNS is commonly unsupported on @@ -1783,6 +1774,7 @@ static unsigned char *ext_target_model[] = { "MSA2312", "MSA2324", "P2000 G3 SAS", + "MSA 2040 SAS", NULL, }; @@ -3171,7 +3163,7 @@ static int hpsa_big_passthru_ioctl(struct ctlr_info *h, void __user *argp) hpsa_pci_unmap(h->pdev, c, i, PCI_DMA_BIDIRECTIONAL); status = -ENOMEM; - goto cleanup1; + goto cleanup0; } c->SG[i].Addr.lower = temp64.val32.lower; c->SG[i].Addr.upper = temp64.val32.upper; @@ -3187,24 +3179,23 @@ static int hpsa_big_passthru_ioctl(struct ctlr_info *h, void __user *argp) /* Copy the error information out */ memcpy(&ioc->error_info, c->err_info, sizeof(ioc->error_info)); if (copy_to_user(argp, ioc, sizeof(*ioc))) { - cmd_special_free(h, c); status = -EFAULT; - goto cleanup1; + goto cleanup0; } if (ioc->Request.Type.Direction == XFER_READ && ioc->buf_size > 0) { /* Copy the data out of the buffer we created */ BYTE __user *ptr = ioc->buf; for (i = 0; i < sg_used; i++) { if (copy_to_user(ptr, buff[i], buff_size[i])) { - cmd_special_free(h, c); status = -EFAULT; - goto cleanup1; + goto cleanup0; } ptr += buff_size[i]; } } - cmd_special_free(h, c); status = 0; +cleanup0: + cmd_special_free(h, c); cleanup1: if (buff) { for (i = 0; i < sg_used; i++) @@ -3223,6 +3214,36 @@ static void check_ioctl_unit_attention(struct ctlr_info *h, c->err_info->ScsiStatus != SAM_STAT_CHECK_CONDITION) (void) check_for_unit_attention(h, c); } + +static int increment_passthru_count(struct ctlr_info *h) +{ + unsigned long flags; + + spin_lock_irqsave(&h->passthru_count_lock, flags); + if (h->passthru_count >= HPSA_MAX_CONCURRENT_PASSTHRUS) { + spin_unlock_irqrestore(&h->passthru_count_lock, flags); + return -1; + } + h->passthru_count++; + spin_unlock_irqrestore(&h->passthru_count_lock, flags); + return 0; +} + +static void decrement_passthru_count(struct ctlr_info *h) +{ + unsigned long flags; + + spin_lock_irqsave(&h->passthru_count_lock, flags); + if (h->passthru_count <= 0) { + spin_unlock_irqrestore(&h->passthru_count_lock, flags); + /* not expecting to get here. */ + dev_warn(&h->pdev->dev, "Bug detected, passthru_count seems to be incorrect.\n"); + return; + } + h->passthru_count--; + spin_unlock_irqrestore(&h->passthru_count_lock, flags); +} + /* * ioctl */ @@ -3230,6 +3251,7 @@ static int hpsa_ioctl(struct scsi_device *dev, int cmd, void *arg) { struct ctlr_info *h; void __user *argp = (void __user *)arg; + int rc; h = sdev_to_hba(dev); @@ -3244,9 +3266,17 @@ static int hpsa_ioctl(struct scsi_device *dev, int cmd, void *arg) case CCISS_GETDRIVVER: return hpsa_getdrivver_ioctl(h, argp); case CCISS_PASSTHRU: - return hpsa_passthru_ioctl(h, argp); + if (increment_passthru_count(h)) + return -EAGAIN; + rc = hpsa_passthru_ioctl(h, argp); + decrement_passthru_count(h); + return rc; case CCISS_BIG_PASSTHRU: - return hpsa_big_passthru_ioctl(h, argp); + if (increment_passthru_count(h)) + return -EAGAIN; + rc = hpsa_big_passthru_ioctl(h, argp); + decrement_passthru_count(h); + return rc; default: return -ENOTTY; } @@ -3445,9 +3475,11 @@ static void start_io(struct ctlr_info *h) c = list_entry(h->reqQ.next, struct CommandList, list); /* can't do anything if fifo is full */ if ((h->access.fifo_full(h))) { + h->fifo_recently_full = 1; dev_warn(&h->pdev->dev, "fifo full\n"); break; } + h->fifo_recently_full = 0; /* Get the first entry from the Request Q */ removeQ(c); @@ -3501,15 +3533,41 @@ static inline int bad_tag(struct ctlr_info *h, u32 tag_index, static inline void finish_cmd(struct CommandList *c) { unsigned long flags; + int io_may_be_stalled = 0; + struct ctlr_info *h = c->h; - spin_lock_irqsave(&c->h->lock, flags); + spin_lock_irqsave(&h->lock, flags); removeQ(c); - spin_unlock_irqrestore(&c->h->lock, flags); + + /* + * Check for possibly stalled i/o. + * + * If a fifo_full condition is encountered, requests will back up + * in h->reqQ. This queue is only emptied out by start_io which is + * only called when a new i/o request comes in. If no i/o's are + * forthcoming, the i/o's in h->reqQ can get stuck. So we call + * start_io from here if we detect such a danger. + * + * Normally, we shouldn't hit this case, but pounding on the + * CCISS_PASSTHRU ioctl can provoke it. Only call start_io if + * commands_outstanding is low. We want to avoid calling + * start_io from in here as much as possible, and esp. don't + * want to get in a cycle where we call start_io every time + * through here. + */ + if (unlikely(h->fifo_recently_full) && + h->commands_outstanding < 5) + io_may_be_stalled = 1; + + spin_unlock_irqrestore(&h->lock, flags); + dial_up_lockup_detection_on_fw_flash_complete(c->h, c); if (likely(c->cmd_type == CMD_SCSI)) complete_scsi_command(c); else if (c->cmd_type == CMD_IOCTL_PEND) complete(c->waiting); + if (unlikely(io_may_be_stalled)) + start_io(h); } static inline u32 hpsa_tag_contains_index(u32 tag) @@ -3785,6 +3843,13 @@ static int hpsa_controller_hard_reset(struct pci_dev *pdev, */ dev_info(&pdev->dev, "using doorbell to reset controller\n"); writel(use_doorbell, vaddr + SA5_DOORBELL); + + /* PMC hardware guys tell us we need a 5 second delay after + * doorbell reset and before any attempt to talk to the board + * at all to ensure that this actually works and doesn't fall + * over in some weird corner cases. + */ + msleep(5000); } else { /* Try to do it the PCI power state way */ /* Quoting from the Open CISS Specification: "The Power @@ -3981,16 +4046,6 @@ static int hpsa_kdump_hard_reset_controller(struct pci_dev *pdev) need a little pause here */ msleep(HPSA_POST_RESET_PAUSE_MSECS); - /* Wait for board to become not ready, then ready. */ - dev_info(&pdev->dev, "Waiting for board to reset.\n"); - rc = hpsa_wait_for_board_state(pdev, vaddr, BOARD_NOT_READY); - if (rc) { - dev_warn(&pdev->dev, - "failed waiting for board to reset." - " Will try soft reset.\n"); - rc = -ENOTSUPP; /* Not expected, but try soft reset later */ - goto unmap_cfgtable; - } rc = hpsa_wait_for_board_state(pdev, vaddr, BOARD_READY); if (rc) { dev_warn(&pdev->dev, @@ -4308,16 +4363,17 @@ static inline bool hpsa_CISS_signature_present(struct ctlr_info *h) return true; } -/* Need to enable prefetch in the SCSI core for 6400 in x86 */ -static inline void hpsa_enable_scsi_prefetch(struct ctlr_info *h) +static inline void hpsa_set_driver_support_bits(struct ctlr_info *h) { -#ifdef CONFIG_X86 - u32 prefetch; + u32 driver_support; - prefetch = readl(&(h->cfgtable->SCSI_Prefetch)); - prefetch |= 0x100; - writel(prefetch, &(h->cfgtable->SCSI_Prefetch)); +#ifdef CONFIG_X86 + /* Need to enable prefetch in the SCSI core for 6400 in x86 */ + driver_support = readl(&(h->cfgtable->driver_support)); + driver_support |= ENABLE_SCSI_PREFETCH; #endif + driver_support |= ENABLE_UNIT_ATTN; + writel(driver_support, &(h->cfgtable->driver_support)); } /* Disable DMA prefetch for the P600. Otherwise an ASIC bug may result @@ -4427,7 +4483,7 @@ static int hpsa_pci_init(struct ctlr_info *h) err = -ENODEV; goto err_out_free_res; } - hpsa_enable_scsi_prefetch(h); + hpsa_set_driver_support_bits(h); hpsa_p600_dma_prefetch_quirk(h); err = hpsa_enter_simple_mode(h); if (err) @@ -4638,16 +4694,6 @@ static void hpsa_undo_allocations_after_kdump_soft_reset(struct ctlr_info *h) kfree(h); } -static void remove_ctlr_from_lockup_detector_list(struct ctlr_info *h) -{ - assert_spin_locked(&lockup_detector_lock); - if (!hpsa_lockup_detector) - return; - if (h->lockup_detected) - return; /* already stopped the lockup detector */ - list_del(&h->lockup_list); -} - /* Called when controller lockup detected. */ static void fail_all_cmds_on_list(struct ctlr_info *h, struct list_head *list) { @@ -4666,8 +4712,6 @@ static void controller_lockup_detected(struct ctlr_info *h) { unsigned long flags; - assert_spin_locked(&lockup_detector_lock); - remove_ctlr_from_lockup_detector_list(h); h->access.set_intr_mask(h, HPSA_INTR_OFF); spin_lock_irqsave(&h->lock, flags); h->lockup_detected = readl(h->vaddr + SA5_SCRATCHPAD_OFFSET); @@ -4687,7 +4731,6 @@ static void detect_controller_lockup(struct ctlr_info *h) u32 heartbeat; unsigned long flags; - assert_spin_locked(&lockup_detector_lock); now = get_jiffies_64(); /* If we've received an interrupt recently, we're ok. */ if (time_after64(h->last_intr_timestamp + @@ -4717,68 +4760,22 @@ static void detect_controller_lockup(struct ctlr_info *h) h->last_heartbeat_timestamp = now; } -static int detect_controller_lockup_thread(void *notused) +static void hpsa_monitor_ctlr_worker(struct work_struct *work) { - struct ctlr_info *h; unsigned long flags; - - while (1) { - struct list_head *this, *tmp; - - schedule_timeout_interruptible(HEARTBEAT_SAMPLE_INTERVAL); - if (kthread_should_stop()) - break; - spin_lock_irqsave(&lockup_detector_lock, flags); - list_for_each_safe(this, tmp, &hpsa_ctlr_list) { - h = list_entry(this, struct ctlr_info, lockup_list); - detect_controller_lockup(h); - } - spin_unlock_irqrestore(&lockup_detector_lock, flags); - } - return 0; -} - -static void add_ctlr_to_lockup_detector_list(struct ctlr_info *h) -{ - unsigned long flags; - - h->heartbeat_sample_interval = HEARTBEAT_SAMPLE_INTERVAL; - spin_lock_irqsave(&lockup_detector_lock, flags); - list_add_tail(&h->lockup_list, &hpsa_ctlr_list); - spin_unlock_irqrestore(&lockup_detector_lock, flags); -} - -static void start_controller_lockup_detector(struct ctlr_info *h) -{ - /* Start the lockup detector thread if not already started */ - if (!hpsa_lockup_detector) { - spin_lock_init(&lockup_detector_lock); - hpsa_lockup_detector = - kthread_run(detect_controller_lockup_thread, - NULL, HPSA); - } - if (!hpsa_lockup_detector) { - dev_warn(&h->pdev->dev, - "Could not start lockup detector thread\n"); + struct ctlr_info *h = container_of(to_delayed_work(work), + struct ctlr_info, monitor_ctlr_work); + detect_controller_lockup(h); + if (h->lockup_detected) + return; + spin_lock_irqsave(&h->lock, flags); + if (h->remove_in_progress) { + spin_unlock_irqrestore(&h->lock, flags); return; } - add_ctlr_to_lockup_detector_list(h); -} - -static void stop_controller_lockup_detector(struct ctlr_info *h) -{ - unsigned long flags; - - spin_lock_irqsave(&lockup_detector_lock, flags); - remove_ctlr_from_lockup_detector_list(h); - /* If the list of ctlr's to monitor is empty, stop the thread */ - if (list_empty(&hpsa_ctlr_list)) { - spin_unlock_irqrestore(&lockup_detector_lock, flags); - kthread_stop(hpsa_lockup_detector); - spin_lock_irqsave(&lockup_detector_lock, flags); - hpsa_lockup_detector = NULL; - } - spin_unlock_irqrestore(&lockup_detector_lock, flags); + schedule_delayed_work(&h->monitor_ctlr_work, + h->heartbeat_sample_interval); + spin_unlock_irqrestore(&h->lock, flags); } static int hpsa_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) @@ -4822,6 +4819,7 @@ reinit_after_soft_reset: INIT_LIST_HEAD(&h->reqQ); spin_lock_init(&h->lock); spin_lock_init(&h->scan_lock); + spin_lock_init(&h->passthru_count_lock); rc = hpsa_pci_init(h); if (rc != 0) goto clean1; @@ -4925,7 +4923,12 @@ reinit_after_soft_reset: hpsa_hba_inquiry(h); hpsa_register_scsi(h); /* hook ourselves into SCSI subsystem */ - start_controller_lockup_detector(h); + + /* Monitor the controller for firmware lockups */ + h->heartbeat_sample_interval = HEARTBEAT_SAMPLE_INTERVAL; + INIT_DELAYED_WORK(&h->monitor_ctlr_work, hpsa_monitor_ctlr_worker); + schedule_delayed_work(&h->monitor_ctlr_work, + h->heartbeat_sample_interval); return 0; clean4: @@ -4942,6 +4945,15 @@ static void hpsa_flush_cache(struct ctlr_info *h) { char *flush_buf; struct CommandList *c; + unsigned long flags; + + /* Don't bother trying to flush the cache if locked up */ + spin_lock_irqsave(&h->lock, flags); + if (unlikely(h->lockup_detected)) { + spin_unlock_irqrestore(&h->lock, flags); + return; + } + spin_unlock_irqrestore(&h->lock, flags); flush_buf = kzalloc(4, GFP_KERNEL); if (!flush_buf) @@ -4991,13 +5003,20 @@ static void hpsa_free_device_info(struct ctlr_info *h) static void hpsa_remove_one(struct pci_dev *pdev) { struct ctlr_info *h; + unsigned long flags; if (pci_get_drvdata(pdev) == NULL) { dev_err(&pdev->dev, "unable to remove device\n"); return; } h = pci_get_drvdata(pdev); - stop_controller_lockup_detector(h); + + /* Get rid of any controller monitoring work items */ + spin_lock_irqsave(&h->lock, flags); + h->remove_in_progress = 1; + cancel_delayed_work(&h->monitor_ctlr_work); + spin_unlock_irqrestore(&h->lock, flags); + hpsa_unregister_scsi(h); /* unhook from SCSI subsystem */ hpsa_shutdown(pdev); iounmap(h->vaddr); diff --git a/drivers/scsi/hpsa.h b/drivers/scsi/hpsa.h index bc85e7244f4..01c328349c8 100644 --- a/drivers/scsi/hpsa.h +++ b/drivers/scsi/hpsa.h @@ -114,6 +114,11 @@ struct ctlr_info { struct TransTable_struct *transtable; unsigned long transMethod; + /* cap concurrent passthrus at some reasonable maximum */ +#define HPSA_MAX_CONCURRENT_PASSTHRUS (20) + spinlock_t passthru_count_lock; /* protects passthru_count */ + int passthru_count; + /* * Performant mode completion buffers */ @@ -130,7 +135,9 @@ struct ctlr_info { u32 heartbeat_sample_interval; atomic_t firmware_flash_in_progress; u32 lockup_detected; - struct list_head lockup_list; + struct delayed_work monitor_ctlr_work; + int remove_in_progress; + u32 fifo_recently_full; /* Address of h->q[x] is passed to intr handler to know which queue */ u8 q[MAX_REPLY_QUEUES]; u32 TMFSupportFlags; /* cache what task mgmt funcs are supported. */ diff --git a/drivers/scsi/hpsa_cmd.h b/drivers/scsi/hpsa_cmd.h index a894f2eca7a..bfc8c4ea66f 100644 --- a/drivers/scsi/hpsa_cmd.h +++ b/drivers/scsi/hpsa_cmd.h @@ -356,7 +356,9 @@ struct CfgTable { u32 TransMethodOffset; u8 ServerName[16]; u32 HeartBeat; - u32 SCSI_Prefetch; + u32 driver_support; +#define ENABLE_SCSI_PREFETCH 0x100 +#define ENABLE_UNIT_ATTN 0x01 u32 MaxScatterGatherElements; u32 MaxLogicalUnits; u32 MaxPhysicalDevices; diff --git a/drivers/scsi/ipr.c b/drivers/scsi/ipr.c index 573f4128b6b..3f5b56a9989 100644 --- a/drivers/scsi/ipr.c +++ b/drivers/scsi/ipr.c @@ -220,7 +220,7 @@ module_param_named(max_devs, ipr_max_devs, int, 0); MODULE_PARM_DESC(max_devs, "Specify the maximum number of physical devices. " "[Default=" __stringify(IPR_DEFAULT_SIS64_DEVS) "]"); module_param_named(number_of_msix, ipr_number_of_msix, int, 0); -MODULE_PARM_DESC(number_of_msix, "Specify the number of MSIX interrupts to use on capable adapters (1 - 5). (default:2)"); +MODULE_PARM_DESC(number_of_msix, "Specify the number of MSIX interrupts to use on capable adapters (1 - 16). (default:2)"); MODULE_LICENSE("GPL"); MODULE_VERSION(IPR_DRIVER_VERSION); diff --git a/drivers/scsi/ipr.h b/drivers/scsi/ipr.h index cad1483f05d..9ce38a22647 100644 --- a/drivers/scsi/ipr.h +++ b/drivers/scsi/ipr.h @@ -301,7 +301,7 @@ IPR_PCII_NO_HOST_RRQ | IPR_PCII_IOARRIN_LOST | IPR_PCII_MMIO_ERROR) * Dump literals */ #define IPR_FMT2_MAX_IOA_DUMP_SIZE (4 * 1024 * 1024) -#define IPR_FMT3_MAX_IOA_DUMP_SIZE (32 * 1024 * 1024) +#define IPR_FMT3_MAX_IOA_DUMP_SIZE (80 * 1024 * 1024) #define IPR_FMT2_NUM_SDT_ENTRIES 511 #define IPR_FMT3_NUM_SDT_ENTRIES 0xFFF #define IPR_FMT2_MAX_NUM_DUMP_PAGES ((IPR_FMT2_MAX_IOA_DUMP_SIZE / PAGE_SIZE) + 1) @@ -311,7 +311,7 @@ IPR_PCII_NO_HOST_RRQ | IPR_PCII_IOARRIN_LOST | IPR_PCII_MMIO_ERROR) * Misc literals */ #define IPR_NUM_IOADL_ENTRIES IPR_MAX_SGLIST -#define IPR_MAX_MSIX_VECTORS 0x5 +#define IPR_MAX_MSIX_VECTORS 0x10 #define IPR_MAX_HRRQ_NUM 0x10 #define IPR_INIT_HRRQ 0x0 diff --git a/drivers/scsi/libiscsi.c b/drivers/scsi/libiscsi.c index e3995612ea7..40462415291 100644 --- a/drivers/scsi/libiscsi.c +++ b/drivers/scsi/libiscsi.c @@ -2945,6 +2945,7 @@ void iscsi_conn_teardown(struct iscsi_cls_conn *cls_conn) free_pages((unsigned long) conn->data, get_order(ISCSI_DEF_MAX_RECV_SEG_LEN)); kfree(conn->persistent_address); + kfree(conn->local_ipaddr); kfifo_in(&session->cmdpool.queue, (void*)&conn->login_task, sizeof(void*)); if (session->leadconn == conn) @@ -3269,6 +3270,8 @@ int iscsi_set_param(struct iscsi_cls_conn *cls_conn, sscanf(buf, "%d", &val); session->discovery_sess = !!val; break; + case ISCSI_PARAM_LOCAL_IPADDR: + return iscsi_switch_str_param(&conn->local_ipaddr, buf); default: return -ENOSYS; } @@ -3542,6 +3545,9 @@ int iscsi_conn_get_param(struct iscsi_cls_conn *cls_conn, case ISCSI_PARAM_TCP_RECV_WSF: len = sprintf(buf, "%u\n", conn->tcp_recv_wsf); break; + case ISCSI_PARAM_LOCAL_IPADDR: + len = sprintf(buf, "%s\n", conn->local_ipaddr); + break; default: return -ENOSYS; } diff --git a/drivers/scsi/libsas/sas_expander.c b/drivers/scsi/libsas/sas_expander.c index 446b85110a1..0cac7d8fd0f 100644 --- a/drivers/scsi/libsas/sas_expander.c +++ b/drivers/scsi/libsas/sas_expander.c @@ -2163,10 +2163,10 @@ int sas_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, } /* do we need to support multiple segments? */ - if (bio_segments(req->bio) > 1 || bio_segments(rsp->bio) > 1) { - printk("%s: multiple segments req %u %u, rsp %u %u\n", - __func__, bio_segments(req->bio), blk_rq_bytes(req), - bio_segments(rsp->bio), blk_rq_bytes(rsp)); + if (bio_multiple_segments(req->bio) || + bio_multiple_segments(rsp->bio)) { + printk("%s: multiple segments req %u, rsp %u\n", + __func__, blk_rq_bytes(req), blk_rq_bytes(rsp)); return -EINVAL; } diff --git a/drivers/scsi/lpfc/lpfc_debugfs.c b/drivers/scsi/lpfc/lpfc_debugfs.c index 60084e6ad2f..b800cc952ca 100644 --- a/drivers/scsi/lpfc/lpfc_debugfs.c +++ b/drivers/scsi/lpfc/lpfc_debugfs.c @@ -4001,7 +4001,7 @@ lpfc_debugfs_initialize(struct lpfc_vport *vport) goto debug_failed; } } else - phba->debug_dumpHBASlim = NULL; + phba->debug_dumpHostSlim = NULL; /* Setup dumpData */ snprintf(name, sizeof(name), "dumpData"); diff --git a/drivers/scsi/mac_scsi.c b/drivers/scsi/mac_scsi.c index 858075723c8..f5cdc68cd5b 100644 --- a/drivers/scsi/mac_scsi.c +++ b/drivers/scsi/mac_scsi.c @@ -260,6 +260,8 @@ int __init macscsi_detect(struct scsi_host_template * tpnt) /* Once we support multiple 5380s (e.g. DuoDock) we'll do something different here */ instance = scsi_register (tpnt, sizeof(struct NCR5380_hostdata)); + if (instance == NULL) + return 0; if (macintosh_config->ident == MAC_MODEL_IIFX) { mac_scsi_regp = via1+0x8000; diff --git a/drivers/scsi/megaraid/megaraid_sas.h b/drivers/scsi/megaraid/megaraid_sas.h index e9e543c5848..34452ea386a 100644 --- a/drivers/scsi/megaraid/megaraid_sas.h +++ b/drivers/scsi/megaraid/megaraid_sas.h @@ -1527,7 +1527,6 @@ struct megasas_instance { u32 *reply_queue; dma_addr_t reply_queue_h; - unsigned long base_addr; struct megasas_register_set __iomem *reg_set; u32 *reply_post_host_index_addr[MR_MAX_MSIX_REG_ARRAY]; struct megasas_pd_list pd_list[MEGASAS_MAX_PD]; diff --git a/drivers/scsi/megaraid/megaraid_sas_base.c b/drivers/scsi/megaraid/megaraid_sas_base.c index c99812bf2a7..3b7ad10497f 100644 --- a/drivers/scsi/megaraid/megaraid_sas_base.c +++ b/drivers/scsi/megaraid/megaraid_sas_base.c @@ -3615,6 +3615,7 @@ static int megasas_init_fw(struct megasas_instance *instance) u32 max_sectors_1; u32 max_sectors_2; u32 tmp_sectors, msix_enable, scratch_pad_2; + resource_size_t base_addr; struct megasas_register_set __iomem *reg_set; struct megasas_ctrl_info *ctrl_info; unsigned long bar_list; @@ -3623,14 +3624,14 @@ static int megasas_init_fw(struct megasas_instance *instance) /* Find first memory bar */ bar_list = pci_select_bars(instance->pdev, IORESOURCE_MEM); instance->bar = find_first_bit(&bar_list, sizeof(unsigned long)); - instance->base_addr = pci_resource_start(instance->pdev, instance->bar); if (pci_request_selected_regions(instance->pdev, instance->bar, "megasas: LSI")) { printk(KERN_DEBUG "megasas: IO memory region busy!\n"); return -EBUSY; } - instance->reg_set = ioremap_nocache(instance->base_addr, 8192); + base_addr = pci_resource_start(instance->pdev, instance->bar); + instance->reg_set = ioremap_nocache(base_addr, 8192); if (!instance->reg_set) { printk(KERN_DEBUG "megasas: Failed to map IO mem\n"); diff --git a/drivers/scsi/mpt2sas/mpt2sas_base.c b/drivers/scsi/mpt2sas/mpt2sas_base.c index 3901edc3581..bde63f7452b 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_base.c +++ b/drivers/scsi/mpt2sas/mpt2sas_base.c @@ -128,7 +128,7 @@ static int mpt2sas_remove_dead_ioc_func(void *arg) pdev = ioc->pdev; if ((pdev == NULL)) return -1; - pci_stop_and_remove_bus_device(pdev); + pci_stop_and_remove_bus_device_locked(pdev); return 0; } diff --git a/drivers/scsi/mpt2sas/mpt2sas_transport.c b/drivers/scsi/mpt2sas/mpt2sas_transport.c index 9d26637308b..410f4a3e888 100644 --- a/drivers/scsi/mpt2sas/mpt2sas_transport.c +++ b/drivers/scsi/mpt2sas/mpt2sas_transport.c @@ -1901,7 +1901,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, struct MPT2SAS_ADAPTER *ioc = shost_priv(shost); Mpi2SmpPassthroughRequest_t *mpi_request; Mpi2SmpPassthroughReply_t *mpi_reply; - int rc, i; + int rc; u16 smid; u32 ioc_state; unsigned long timeleft; @@ -1916,7 +1916,8 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, void *pci_addr_out = NULL; u16 wait_state_count; struct request *rsp = req->next_rq; - struct bio_vec *bvec = NULL; + struct bio_vec bvec; + struct bvec_iter iter; if (!rsp) { printk(MPT2SAS_ERR_FMT "%s: the smp response space is " @@ -1942,7 +1943,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, ioc->transport_cmds.status = MPT2_CMD_PENDING; /* Check if the request is split across multiple segments */ - if (bio_segments(req->bio) > 1) { + if (bio_multiple_segments(req->bio)) { u32 offset = 0; /* Allocate memory and copy the request */ @@ -1955,11 +1956,11 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, goto out; } - bio_for_each_segment(bvec, req->bio, i) { + bio_for_each_segment(bvec, req->bio, iter) { memcpy(pci_addr_out + offset, - page_address(bvec->bv_page) + bvec->bv_offset, - bvec->bv_len); - offset += bvec->bv_len; + page_address(bvec.bv_page) + bvec.bv_offset, + bvec.bv_len); + offset += bvec.bv_len; } } else { dma_addr_out = pci_map_single(ioc->pdev, bio_data(req->bio), @@ -1974,7 +1975,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, /* Check if the response needs to be populated across * multiple segments */ - if (bio_segments(rsp->bio) > 1) { + if (bio_multiple_segments(rsp->bio)) { pci_addr_in = pci_alloc_consistent(ioc->pdev, blk_rq_bytes(rsp), &pci_dma_in); if (!pci_addr_in) { @@ -2041,7 +2042,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, sgl_flags = (MPI2_SGE_FLAGS_SIMPLE_ELEMENT | MPI2_SGE_FLAGS_END_OF_BUFFER | MPI2_SGE_FLAGS_HOST_TO_IOC); sgl_flags = sgl_flags << MPI2_SGE_FLAGS_SHIFT; - if (bio_segments(req->bio) > 1) { + if (bio_multiple_segments(req->bio)) { ioc->base_add_sg_single(psge, sgl_flags | (blk_rq_bytes(req) - 4), pci_dma_out); } else { @@ -2057,7 +2058,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, MPI2_SGE_FLAGS_LAST_ELEMENT | MPI2_SGE_FLAGS_END_OF_BUFFER | MPI2_SGE_FLAGS_END_OF_LIST); sgl_flags = sgl_flags << MPI2_SGE_FLAGS_SHIFT; - if (bio_segments(rsp->bio) > 1) { + if (bio_multiple_segments(rsp->bio)) { ioc->base_add_sg_single(psge, sgl_flags | (blk_rq_bytes(rsp) + 4), pci_dma_in); } else { @@ -2102,23 +2103,23 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, le16_to_cpu(mpi_reply->ResponseDataLength); /* check if the resp needs to be copied from the allocated * pci mem */ - if (bio_segments(rsp->bio) > 1) { + if (bio_multiple_segments(rsp->bio)) { u32 offset = 0; u32 bytes_to_copy = le16_to_cpu(mpi_reply->ResponseDataLength); - bio_for_each_segment(bvec, rsp->bio, i) { - if (bytes_to_copy <= bvec->bv_len) { - memcpy(page_address(bvec->bv_page) + - bvec->bv_offset, pci_addr_in + + bio_for_each_segment(bvec, rsp->bio, iter) { + if (bytes_to_copy <= bvec.bv_len) { + memcpy(page_address(bvec.bv_page) + + bvec.bv_offset, pci_addr_in + offset, bytes_to_copy); break; } else { - memcpy(page_address(bvec->bv_page) + - bvec->bv_offset, pci_addr_in + - offset, bvec->bv_len); - bytes_to_copy -= bvec->bv_len; + memcpy(page_address(bvec.bv_page) + + bvec.bv_offset, pci_addr_in + + offset, bvec.bv_len); + bytes_to_copy -= bvec.bv_len; } - offset += bvec->bv_len; + offset += bvec.bv_len; } } } else { diff --git a/drivers/scsi/mpt3sas/mpt3sas_base.c b/drivers/scsi/mpt3sas/mpt3sas_base.c index fa785062e97..0cf4f7000f9 100644 --- a/drivers/scsi/mpt3sas/mpt3sas_base.c +++ b/drivers/scsi/mpt3sas/mpt3sas_base.c @@ -131,7 +131,7 @@ static int mpt3sas_remove_dead_ioc_func(void *arg) pdev = ioc->pdev; if ((pdev == NULL)) return -1; - pci_stop_and_remove_bus_device(pdev); + pci_stop_and_remove_bus_device_locked(pdev); return 0; } diff --git a/drivers/scsi/mpt3sas/mpt3sas_transport.c b/drivers/scsi/mpt3sas/mpt3sas_transport.c index e771a88c6a7..65170cb1a00 100644 --- a/drivers/scsi/mpt3sas/mpt3sas_transport.c +++ b/drivers/scsi/mpt3sas/mpt3sas_transport.c @@ -1884,7 +1884,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, struct MPT3SAS_ADAPTER *ioc = shost_priv(shost); Mpi2SmpPassthroughRequest_t *mpi_request; Mpi2SmpPassthroughReply_t *mpi_reply; - int rc, i; + int rc; u16 smid; u32 ioc_state; unsigned long timeleft; @@ -1898,7 +1898,8 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, void *pci_addr_out = NULL; u16 wait_state_count; struct request *rsp = req->next_rq; - struct bio_vec *bvec = NULL; + struct bio_vec bvec; + struct bvec_iter iter; if (!rsp) { pr_err(MPT3SAS_FMT "%s: the smp response space is missing\n", @@ -1925,7 +1926,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, ioc->transport_cmds.status = MPT3_CMD_PENDING; /* Check if the request is split across multiple segments */ - if (req->bio->bi_vcnt > 1) { + if (bio_multiple_segments(req->bio)) { u32 offset = 0; /* Allocate memory and copy the request */ @@ -1938,11 +1939,11 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, goto out; } - bio_for_each_segment(bvec, req->bio, i) { + bio_for_each_segment(bvec, req->bio, iter) { memcpy(pci_addr_out + offset, - page_address(bvec->bv_page) + bvec->bv_offset, - bvec->bv_len); - offset += bvec->bv_len; + page_address(bvec.bv_page) + bvec.bv_offset, + bvec.bv_len); + offset += bvec.bv_len; } } else { dma_addr_out = pci_map_single(ioc->pdev, bio_data(req->bio), @@ -1957,7 +1958,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, /* Check if the response needs to be populated across * multiple segments */ - if (rsp->bio->bi_vcnt > 1) { + if (bio_multiple_segments(rsp->bio)) { pci_addr_in = pci_alloc_consistent(ioc->pdev, blk_rq_bytes(rsp), &pci_dma_in); if (!pci_addr_in) { @@ -2018,7 +2019,7 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, mpi_request->RequestDataLength = cpu_to_le16(blk_rq_bytes(req) - 4); psge = &mpi_request->SGL; - if (req->bio->bi_vcnt > 1) + if (bio_multiple_segments(req->bio)) ioc->build_sg(ioc, psge, pci_dma_out, (blk_rq_bytes(req) - 4), pci_dma_in, (blk_rq_bytes(rsp) + 4)); else @@ -2063,23 +2064,23 @@ _transport_smp_handler(struct Scsi_Host *shost, struct sas_rphy *rphy, /* check if the resp needs to be copied from the allocated * pci mem */ - if (rsp->bio->bi_vcnt > 1) { + if (bio_multiple_segments(rsp->bio)) { u32 offset = 0; u32 bytes_to_copy = le16_to_cpu(mpi_reply->ResponseDataLength); - bio_for_each_segment(bvec, rsp->bio, i) { - if (bytes_to_copy <= bvec->bv_len) { - memcpy(page_address(bvec->bv_page) + - bvec->bv_offset, pci_addr_in + + bio_for_each_segment(bvec, rsp->bio, iter) { + if (bytes_to_copy <= bvec.bv_len) { + memcpy(page_address(bvec.bv_page) + + bvec.bv_offset, pci_addr_in + offset, bytes_to_copy); break; } else { - memcpy(page_address(bvec->bv_page) + - bvec->bv_offset, pci_addr_in + - offset, bvec->bv_len); - bytes_to_copy -= bvec->bv_len; + memcpy(page_address(bvec.bv_page) + + bvec.bv_offset, pci_addr_in + + offset, bvec.bv_len); + bytes_to_copy -= bvec.bv_len; } - offset += bvec->bv_len; + offset += bvec.bv_len; } } } else { diff --git a/drivers/scsi/osd/osd_initiator.c b/drivers/scsi/osd/osd_initiator.c index aa66361ed44..bac04c2335a 100644 --- a/drivers/scsi/osd/osd_initiator.c +++ b/drivers/scsi/osd/osd_initiator.c @@ -731,7 +731,7 @@ static int _osd_req_list_objects(struct osd_request *or, bio->bi_rw &= ~REQ_WRITE; or->in.bio = bio; - or->in.total_bytes = bio->bi_size; + or->in.total_bytes = bio->bi_iter.bi_size; return 0; } diff --git a/drivers/scsi/qla1280.c b/drivers/scsi/qla1280.c index 5a522c5bbd4..97dabd39b09 100644 --- a/drivers/scsi/qla1280.c +++ b/drivers/scsi/qla1280.c @@ -2502,7 +2502,7 @@ qla1280_mailbox_command(struct scsi_qla_host *ha, uint8_t mr, uint16_t *mb) /* Issue set host interrupt command. */ /* set up a timer just in case we're really jammed */ - init_timer(&timer); + init_timer_on_stack(&timer); timer.expires = jiffies + 20*HZ; timer.data = (unsigned long)ha; timer.function = qla1280_mailbox_timeout; diff --git a/drivers/scsi/qla2xxx/qla_attr.c b/drivers/scsi/qla2xxx/qla_attr.c index 5f174b83f56..4a0d7c92181 100644 --- a/drivers/scsi/qla2xxx/qla_attr.c +++ b/drivers/scsi/qla2xxx/qla_attr.c @@ -862,7 +862,7 @@ qla2x00_alloc_sysfs_attr(scsi_qla_host_t *vha) } void -qla2x00_free_sysfs_attr(scsi_qla_host_t *vha) +qla2x00_free_sysfs_attr(scsi_qla_host_t *vha, bool stop_beacon) { struct Scsi_Host *host = vha->host; struct sysfs_entry *iter; @@ -880,7 +880,7 @@ qla2x00_free_sysfs_attr(scsi_qla_host_t *vha) iter->attr); } - if (ha->beacon_blink_led == 1) + if (stop_beacon && ha->beacon_blink_led == 1) ha->isp_ops->beacon_off(vha); } @@ -890,7 +890,7 @@ static ssize_t qla2x00_drvr_version_show(struct device *dev, struct device_attribute *attr, char *buf) { - return snprintf(buf, PAGE_SIZE, "%s\n", qla2x00_version_str); + return scnprintf(buf, PAGE_SIZE, "%s\n", qla2x00_version_str); } static ssize_t @@ -901,7 +901,7 @@ qla2x00_fw_version_show(struct device *dev, struct qla_hw_data *ha = vha->hw; char fw_str[128]; - return snprintf(buf, PAGE_SIZE, "%s\n", + return scnprintf(buf, PAGE_SIZE, "%s\n", ha->isp_ops->fw_version_str(vha, fw_str)); } @@ -914,15 +914,15 @@ qla2x00_serial_num_show(struct device *dev, struct device_attribute *attr, uint32_t sn; if (IS_QLAFX00(vha->hw)) { - return snprintf(buf, PAGE_SIZE, "%s\n", + return scnprintf(buf, PAGE_SIZE, "%s\n", vha->hw->mr.serial_num); } else if (IS_FWI2_CAPABLE(ha)) { - qla2xxx_get_vpd_field(vha, "SN", buf, PAGE_SIZE); - return snprintf(buf, PAGE_SIZE, "%s\n", buf); + qla2xxx_get_vpd_field(vha, "SN", buf, PAGE_SIZE - 1); + return strlen(strcat(buf, "\n")); } sn = ((ha->serial0 & 0x1f) << 16) | (ha->serial2 << 8) | ha->serial1; - return snprintf(buf, PAGE_SIZE, "%c%05d\n", 'A' + sn / 100000, + return scnprintf(buf, PAGE_SIZE, "%c%05d\n", 'A' + sn / 100000, sn % 100000); } @@ -931,7 +931,7 @@ qla2x00_isp_name_show(struct device *dev, struct device_attribute *attr, char *buf) { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); - return snprintf(buf, PAGE_SIZE, "ISP%04X\n", vha->hw->pdev->device); + return scnprintf(buf, PAGE_SIZE, "ISP%04X\n", vha->hw->pdev->device); } static ssize_t @@ -942,10 +942,10 @@ qla2x00_isp_id_show(struct device *dev, struct device_attribute *attr, struct qla_hw_data *ha = vha->hw; if (IS_QLAFX00(vha->hw)) - return snprintf(buf, PAGE_SIZE, "%s\n", + return scnprintf(buf, PAGE_SIZE, "%s\n", vha->hw->mr.hw_version); - return snprintf(buf, PAGE_SIZE, "%04x %04x %04x %04x\n", + return scnprintf(buf, PAGE_SIZE, "%04x %04x %04x %04x\n", ha->product_id[0], ha->product_id[1], ha->product_id[2], ha->product_id[3]); } @@ -956,11 +956,7 @@ qla2x00_model_name_show(struct device *dev, struct device_attribute *attr, { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); - if (IS_QLAFX00(vha->hw)) - return snprintf(buf, PAGE_SIZE, "%s\n", - vha->hw->mr.product_name); - - return snprintf(buf, PAGE_SIZE, "%s\n", vha->hw->model_number); + return scnprintf(buf, PAGE_SIZE, "%s\n", vha->hw->model_number); } static ssize_t @@ -968,7 +964,7 @@ qla2x00_model_desc_show(struct device *dev, struct device_attribute *attr, char *buf) { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); - return snprintf(buf, PAGE_SIZE, "%s\n", + return scnprintf(buf, PAGE_SIZE, "%s\n", vha->hw->model_desc ? vha->hw->model_desc : ""); } @@ -979,7 +975,7 @@ qla2x00_pci_info_show(struct device *dev, struct device_attribute *attr, scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); char pci_info[30]; - return snprintf(buf, PAGE_SIZE, "%s\n", + return scnprintf(buf, PAGE_SIZE, "%s\n", vha->hw->isp_ops->pci_info_str(vha, pci_info)); } @@ -994,29 +990,29 @@ qla2x00_link_state_show(struct device *dev, struct device_attribute *attr, if (atomic_read(&vha->loop_state) == LOOP_DOWN || atomic_read(&vha->loop_state) == LOOP_DEAD || vha->device_flags & DFLG_NO_CABLE) - len = snprintf(buf, PAGE_SIZE, "Link Down\n"); + len = scnprintf(buf, PAGE_SIZE, "Link Down\n"); else if (atomic_read(&vha->loop_state) != LOOP_READY || qla2x00_reset_active(vha)) - len = snprintf(buf, PAGE_SIZE, "Unknown Link State\n"); + len = scnprintf(buf, PAGE_SIZE, "Unknown Link State\n"); else { - len = snprintf(buf, PAGE_SIZE, "Link Up - "); + len = scnprintf(buf, PAGE_SIZE, "Link Up - "); switch (ha->current_topology) { case ISP_CFG_NL: - len += snprintf(buf + len, PAGE_SIZE-len, "Loop\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "Loop\n"); break; case ISP_CFG_FL: - len += snprintf(buf + len, PAGE_SIZE-len, "FL_Port\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "FL_Port\n"); break; case ISP_CFG_N: - len += snprintf(buf + len, PAGE_SIZE-len, + len += scnprintf(buf + len, PAGE_SIZE-len, "N_Port to N_Port\n"); break; case ISP_CFG_F: - len += snprintf(buf + len, PAGE_SIZE-len, "F_Port\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "F_Port\n"); break; default: - len += snprintf(buf + len, PAGE_SIZE-len, "Loop\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "Loop\n"); break; } } @@ -1032,10 +1028,10 @@ qla2x00_zio_show(struct device *dev, struct device_attribute *attr, switch (vha->hw->zio_mode) { case QLA_ZIO_MODE_6: - len += snprintf(buf + len, PAGE_SIZE-len, "Mode 6\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "Mode 6\n"); break; case QLA_ZIO_DISABLED: - len += snprintf(buf + len, PAGE_SIZE-len, "Disabled\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "Disabled\n"); break; } return len; @@ -1075,7 +1071,7 @@ qla2x00_zio_timer_show(struct device *dev, struct device_attribute *attr, { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); - return snprintf(buf, PAGE_SIZE, "%d us\n", vha->hw->zio_timer * 100); + return scnprintf(buf, PAGE_SIZE, "%d us\n", vha->hw->zio_timer * 100); } static ssize_t @@ -1105,9 +1101,9 @@ qla2x00_beacon_show(struct device *dev, struct device_attribute *attr, int len = 0; if (vha->hw->beacon_blink_led) - len += snprintf(buf + len, PAGE_SIZE-len, "Enabled\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "Enabled\n"); else - len += snprintf(buf + len, PAGE_SIZE-len, "Disabled\n"); + len += scnprintf(buf + len, PAGE_SIZE-len, "Disabled\n"); return len; } @@ -1149,7 +1145,7 @@ qla2x00_optrom_bios_version_show(struct device *dev, { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); struct qla_hw_data *ha = vha->hw; - return snprintf(buf, PAGE_SIZE, "%d.%02d\n", ha->bios_revision[1], + return scnprintf(buf, PAGE_SIZE, "%d.%02d\n", ha->bios_revision[1], ha->bios_revision[0]); } @@ -1159,7 +1155,7 @@ qla2x00_optrom_efi_version_show(struct device *dev, { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); struct qla_hw_data *ha = vha->hw; - return snprintf(buf, PAGE_SIZE, "%d.%02d\n", ha->efi_revision[1], + return scnprintf(buf, PAGE_SIZE, "%d.%02d\n", ha->efi_revision[1], ha->efi_revision[0]); } @@ -1169,7 +1165,7 @@ qla2x00_optrom_fcode_version_show(struct device *dev, { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); struct qla_hw_data *ha = vha->hw; - return snprintf(buf, PAGE_SIZE, "%d.%02d\n", ha->fcode_revision[1], + return scnprintf(buf, PAGE_SIZE, "%d.%02d\n", ha->fcode_revision[1], ha->fcode_revision[0]); } @@ -1179,7 +1175,7 @@ qla2x00_optrom_fw_version_show(struct device *dev, { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); struct qla_hw_data *ha = vha->hw; - return snprintf(buf, PAGE_SIZE, "%d.%02d.%02d %d\n", + return scnprintf(buf, PAGE_SIZE, "%d.%02d.%02d %d\n", ha->fw_revision[0], ha->fw_revision[1], ha->fw_revision[2], ha->fw_revision[3]); } @@ -1192,9 +1188,9 @@ qla2x00_optrom_gold_fw_version_show(struct device *dev, struct qla_hw_data *ha = vha->hw; if (!IS_QLA81XX(ha) && !IS_QLA83XX(ha)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); - return snprintf(buf, PAGE_SIZE, "%d.%02d.%02d (%d)\n", + return scnprintf(buf, PAGE_SIZE, "%d.%02d.%02d (%d)\n", ha->gold_fw_version[0], ha->gold_fw_version[1], ha->gold_fw_version[2], ha->gold_fw_version[3]); } @@ -1204,7 +1200,7 @@ qla2x00_total_isp_aborts_show(struct device *dev, struct device_attribute *attr, char *buf) { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); - return snprintf(buf, PAGE_SIZE, "%d\n", + return scnprintf(buf, PAGE_SIZE, "%d\n", vha->qla_stats.total_isp_aborts); } @@ -1218,16 +1214,16 @@ qla24xx_84xx_fw_version_show(struct device *dev, struct qla_hw_data *ha = vha->hw; if (!IS_QLA84XX(ha)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); if (ha->cs84xx->op_fw_version == 0) rval = qla84xx_verify_chip(vha, status); if ((rval == QLA_SUCCESS) && (status[0] == 0)) - return snprintf(buf, PAGE_SIZE, "%u\n", + return scnprintf(buf, PAGE_SIZE, "%u\n", (uint32_t)ha->cs84xx->op_fw_version); - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); } static ssize_t @@ -1238,9 +1234,9 @@ qla2x00_mpi_version_show(struct device *dev, struct device_attribute *attr, struct qla_hw_data *ha = vha->hw; if (!IS_QLA81XX(ha) && !IS_QLA8031(ha) && !IS_QLA8044(ha)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); - return snprintf(buf, PAGE_SIZE, "%d.%02d.%02d (%x)\n", + return scnprintf(buf, PAGE_SIZE, "%d.%02d.%02d (%x)\n", ha->mpi_version[0], ha->mpi_version[1], ha->mpi_version[2], ha->mpi_capabilities); } @@ -1253,9 +1249,9 @@ qla2x00_phy_version_show(struct device *dev, struct device_attribute *attr, struct qla_hw_data *ha = vha->hw; if (!IS_QLA81XX(ha) && !IS_QLA8031(ha)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); - return snprintf(buf, PAGE_SIZE, "%d.%02d.%02d\n", + return scnprintf(buf, PAGE_SIZE, "%d.%02d.%02d\n", ha->phy_version[0], ha->phy_version[1], ha->phy_version[2]); } @@ -1266,7 +1262,7 @@ qla2x00_flash_block_size_show(struct device *dev, scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); struct qla_hw_data *ha = vha->hw; - return snprintf(buf, PAGE_SIZE, "0x%x\n", ha->fdt_block_size); + return scnprintf(buf, PAGE_SIZE, "0x%x\n", ha->fdt_block_size); } static ssize_t @@ -1276,9 +1272,9 @@ qla2x00_vlan_id_show(struct device *dev, struct device_attribute *attr, scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); if (!IS_CNA_CAPABLE(vha->hw)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); - return snprintf(buf, PAGE_SIZE, "%d\n", vha->fcoe_vlan_id); + return scnprintf(buf, PAGE_SIZE, "%d\n", vha->fcoe_vlan_id); } static ssize_t @@ -1288,9 +1284,9 @@ qla2x00_vn_port_mac_address_show(struct device *dev, scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); if (!IS_CNA_CAPABLE(vha->hw)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); - return snprintf(buf, PAGE_SIZE, "%pMR\n", vha->fcoe_vn_port_mac); + return scnprintf(buf, PAGE_SIZE, "%pMR\n", vha->fcoe_vn_port_mac); } static ssize_t @@ -1299,7 +1295,7 @@ qla2x00_fabric_param_show(struct device *dev, struct device_attribute *attr, { scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); - return snprintf(buf, PAGE_SIZE, "%d\n", vha->hw->switch_cap); + return scnprintf(buf, PAGE_SIZE, "%d\n", vha->hw->switch_cap); } static ssize_t @@ -1320,10 +1316,10 @@ qla2x00_thermal_temp_show(struct device *dev, } if (qla2x00_get_thermal_temp(vha, &temp) == QLA_SUCCESS) - return snprintf(buf, PAGE_SIZE, "%d\n", temp); + return scnprintf(buf, PAGE_SIZE, "%d\n", temp); done: - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); } static ssize_t @@ -1337,7 +1333,7 @@ qla2x00_fw_state_show(struct device *dev, struct device_attribute *attr, if (IS_QLAFX00(vha->hw)) { pstate = qlafx00_fw_state_show(dev, attr, buf); - return snprintf(buf, PAGE_SIZE, "0x%x\n", pstate); + return scnprintf(buf, PAGE_SIZE, "0x%x\n", pstate); } if (qla2x00_reset_active(vha)) @@ -1348,7 +1344,7 @@ qla2x00_fw_state_show(struct device *dev, struct device_attribute *attr, if (rval != QLA_SUCCESS) memset(state, -1, sizeof(state)); - return snprintf(buf, PAGE_SIZE, "0x%x 0x%x 0x%x 0x%x 0x%x\n", state[0], + return scnprintf(buf, PAGE_SIZE, "0x%x 0x%x 0x%x 0x%x 0x%x\n", state[0], state[1], state[2], state[3], state[4]); } @@ -1359,9 +1355,9 @@ qla2x00_diag_requests_show(struct device *dev, scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); if (!IS_BIDI_CAPABLE(vha->hw)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); - return snprintf(buf, PAGE_SIZE, "%llu\n", vha->bidi_stats.io_count); + return scnprintf(buf, PAGE_SIZE, "%llu\n", vha->bidi_stats.io_count); } static ssize_t @@ -1371,9 +1367,9 @@ qla2x00_diag_megabytes_show(struct device *dev, scsi_qla_host_t *vha = shost_priv(class_to_shost(dev)); if (!IS_BIDI_CAPABLE(vha->hw)) - return snprintf(buf, PAGE_SIZE, "\n"); + return scnprintf(buf, PAGE_SIZE, "\n"); - return snprintf(buf, PAGE_SIZE, "%llu\n", + return scnprintf(buf, PAGE_SIZE, "%llu\n", vha->bidi_stats.transfer_bytes >> 20); } @@ -1392,7 +1388,7 @@ qla2x00_fw_dump_size_show(struct device *dev, struct device_attribute *attr, else size = ha->fw_dump_len; - return snprintf(buf, PAGE_SIZE, "%d\n", size); + return scnprintf(buf, PAGE_SIZE, "%d\n", size); } static DEVICE_ATTR(driver_version, S_IRUGO, qla2x00_drvr_version_show, NULL); @@ -1994,6 +1990,8 @@ qla24xx_vport_delete(struct fc_vport *fc_vport) vha->flags.delete_progress = 1; + qlt_remove_target(ha, vha); + fc_remove_host(vha->host); scsi_remove_host(vha->host); diff --git a/drivers/scsi/qla2xxx/qla_bsg.c b/drivers/scsi/qla2xxx/qla_bsg.c index aa57bf0af57..f15d03e6b7e 100644 --- a/drivers/scsi/qla2xxx/qla_bsg.c +++ b/drivers/scsi/qla2xxx/qla_bsg.c @@ -2022,6 +2022,46 @@ done: } static int +qla26xx_serdes_op(struct fc_bsg_job *bsg_job) +{ + struct Scsi_Host *host = bsg_job->shost; + scsi_qla_host_t *vha = shost_priv(host); + int rval = 0; + struct qla_serdes_reg sr; + + memset(&sr, 0, sizeof(sr)); + + sg_copy_to_buffer(bsg_job->request_payload.sg_list, + bsg_job->request_payload.sg_cnt, &sr, sizeof(sr)); + + switch (sr.cmd) { + case INT_SC_SERDES_WRITE_REG: + rval = qla2x00_write_serdes_word(vha, sr.addr, sr.val); + bsg_job->reply->reply_payload_rcv_len = 0; + break; + case INT_SC_SERDES_READ_REG: + rval = qla2x00_read_serdes_word(vha, sr.addr, &sr.val); + sg_copy_from_buffer(bsg_job->reply_payload.sg_list, + bsg_job->reply_payload.sg_cnt, &sr, sizeof(sr)); + bsg_job->reply->reply_payload_rcv_len = sizeof(sr); + break; + default: + ql_log(ql_log_warn, vha, 0x708c, + "Unknown serdes cmd %x.\n", sr.cmd); + rval = -EDOM; + break; + } + + bsg_job->reply->reply_data.vendor_reply.vendor_rsp[0] = + rval ? EXT_STATUS_MAILBOX : 0; + + bsg_job->reply_len = sizeof(struct fc_bsg_reply); + bsg_job->reply->result = DID_OK << 16; + bsg_job->job_done(bsg_job); + return 0; +} + +static int qla2x00_process_vendor_specific(struct fc_bsg_job *bsg_job) { switch (bsg_job->request->rqst_data.h_vendor.vendor_cmd[0]) { @@ -2069,6 +2109,10 @@ qla2x00_process_vendor_specific(struct fc_bsg_job *bsg_job) case QL_VND_FX00_MGMT_CMD: return qlafx00_mgmt_cmd(bsg_job); + + case QL_VND_SERDES_OP: + return qla26xx_serdes_op(bsg_job); + default: return -ENOSYS; } diff --git a/drivers/scsi/qla2xxx/qla_bsg.h b/drivers/scsi/qla2xxx/qla_bsg.h index 04f770332c2..e5c2126221e 100644 --- a/drivers/scsi/qla2xxx/qla_bsg.h +++ b/drivers/scsi/qla2xxx/qla_bsg.h @@ -23,6 +23,7 @@ #define QL_VND_WRITE_I2C 0x10 #define QL_VND_READ_I2C 0x11 #define QL_VND_FX00_MGMT_CMD 0x12 +#define QL_VND_SERDES_OP 0x13 /* BSG Vendor specific subcode returns */ #define EXT_STATUS_OK 0 @@ -212,4 +213,16 @@ struct qla_i2c_access { uint8_t buffer[0x40]; } __packed; +/* 26xx serdes register interface */ + +/* serdes reg commands */ +#define INT_SC_SERDES_READ_REG 1 +#define INT_SC_SERDES_WRITE_REG 2 + +struct qla_serdes_reg { + uint16_t cmd; + uint16_t addr; + uint16_t val; +} __packed; + #endif diff --git a/drivers/scsi/qla2xxx/qla_dbg.c b/drivers/scsi/qla2xxx/qla_dbg.c index ee5c1833eb7..f6103f553bb 100644 --- a/drivers/scsi/qla2xxx/qla_dbg.c +++ b/drivers/scsi/qla2xxx/qla_dbg.c @@ -11,8 +11,9 @@ * ---------------------------------------------------------------------- * | Level | Last Value Used | Holes | * ---------------------------------------------------------------------- - * | Module Init and Probe | 0x0159 | 0x4b,0xba,0xfa | - * | Mailbox commands | 0x1181 | 0x111a-0x111b | + * | Module Init and Probe | 0x015b | 0x4b,0xba,0xfa | + * | | | 0x0x015a | + * | Mailbox commands | 0x1187 | 0x111a-0x111b | * | | | 0x1155-0x1158 | * | | | 0x1018-0x1019 | * | | | 0x1115-0x1116 | @@ -26,7 +27,7 @@ * | | | 0x302d,0x3033 | * | | | 0x3036,0x3038 | * | | | 0x303a | - * | DPC Thread | 0x4022 | 0x4002,0x4013 | + * | DPC Thread | 0x4023 | 0x4002,0x4013 | * | Async Events | 0x5087 | 0x502b-0x502f | * | | | 0x5047,0x5052 | * | | | 0x5084,0x5075 | diff --git a/drivers/scsi/qla2xxx/qla_def.h b/drivers/scsi/qla2xxx/qla_def.h index 93db74ef346..e1fe95ef23e 100644 --- a/drivers/scsi/qla2xxx/qla_def.h +++ b/drivers/scsi/qla2xxx/qla_def.h @@ -862,7 +862,6 @@ struct mbx_cmd_32 { */ #define MBC_LOAD_RAM 1 /* Load RAM. */ #define MBC_EXECUTE_FIRMWARE 2 /* Execute firmware. */ -#define MBC_WRITE_RAM_WORD 4 /* Write RAM word. */ #define MBC_READ_RAM_WORD 5 /* Read RAM word. */ #define MBC_MAILBOX_REGISTER_TEST 6 /* Wrap incoming mailboxes */ #define MBC_VERIFY_CHECKSUM 7 /* Verify checksum. */ @@ -937,6 +936,8 @@ struct mbx_cmd_32 { /* * ISP24xx mailbox commands */ +#define MBC_WRITE_SERDES 0x3 /* Write serdes word. */ +#define MBC_READ_SERDES 0x4 /* Read serdes word. */ #define MBC_SERDES_PARAMS 0x10 /* Serdes Tx Parameters. */ #define MBC_GET_IOCB_STATUS 0x12 /* Get IOCB status command. */ #define MBC_PORT_PARAMS 0x1A /* Port iDMA Parameters. */ @@ -2734,7 +2735,6 @@ struct req_que { srb_t **outstanding_cmds; uint32_t current_outstanding_cmd; uint16_t num_outstanding_cmds; -#define MAX_Q_DEPTH 32 int max_q_depth; dma_addr_t dma_fx00; @@ -2750,6 +2750,13 @@ struct qlfc_fw { uint32_t len; }; +struct scsi_qlt_host { + void *target_lport_ptr; + struct mutex tgt_mutex; + struct mutex tgt_host_action_mutex; + struct qla_tgt *qla_tgt; +}; + struct qlt_hw_data { /* Protected by hw lock */ uint32_t enable_class_2:1; @@ -2765,15 +2772,11 @@ struct qlt_hw_data { uint32_t __iomem *atio_q_in; uint32_t __iomem *atio_q_out; - void *target_lport_ptr; struct qla_tgt_func_tmpl *tgt_ops; - struct qla_tgt *qla_tgt; struct qla_tgt_cmd *cmds[DEFAULT_OUTSTANDING_COMMANDS]; uint16_t current_handle; struct qla_tgt_vp_map *tgt_vp_map; - struct mutex tgt_mutex; - struct mutex tgt_host_action_mutex; int saved_set; uint16_t saved_exchange_count; @@ -3302,12 +3305,7 @@ struct qla_hw_data { struct work_struct nic_core_reset; struct work_struct idc_state_handler; struct work_struct nic_core_unrecoverable; - -#define HOST_QUEUE_RAMPDOWN_INTERVAL (60 * HZ) -#define HOST_QUEUE_RAMPUP_INTERVAL (30 * HZ) - unsigned long host_last_rampdown_time; - unsigned long host_last_rampup_time; - int cfg_lun_q_depth; + struct work_struct board_disable; struct mr_data_fx00 mr; @@ -3372,12 +3370,11 @@ typedef struct scsi_qla_host { #define MPI_RESET_NEEDED 19 /* Initiate MPI FW reset */ #define ISP_QUIESCE_NEEDED 20 /* Driver need some quiescence */ #define SCR_PENDING 21 /* SCR in target mode */ -#define HOST_RAMP_DOWN_QUEUE_DEPTH 22 -#define HOST_RAMP_UP_QUEUE_DEPTH 23 -#define PORT_UPDATE_NEEDED 24 -#define FX00_RESET_RECOVERY 25 -#define FX00_TARGET_SCAN 26 -#define FX00_CRITEMP_RECOVERY 27 +#define PORT_UPDATE_NEEDED 22 +#define FX00_RESET_RECOVERY 23 +#define FX00_TARGET_SCAN 24 +#define FX00_CRITEMP_RECOVERY 25 +#define FX00_HOST_INFO_RESEND 26 uint32_t device_flags; #define SWITCH_FOUND BIT_0 @@ -3441,6 +3438,7 @@ typedef struct scsi_qla_host { #define VP_ERR_FAB_LOGOUT 4 #define VP_ERR_ADAP_NORESOURCES 5 struct qla_hw_data *hw; + struct scsi_qlt_host vha_tgt; struct req_que *req; int fw_heartbeat_counter; int seconds_since_last_heartbeat; diff --git a/drivers/scsi/qla2xxx/qla_gbl.h b/drivers/scsi/qla2xxx/qla_gbl.h index 4446bf5fe29..1f426628a0a 100644 --- a/drivers/scsi/qla2xxx/qla_gbl.h +++ b/drivers/scsi/qla2xxx/qla_gbl.h @@ -98,7 +98,6 @@ extern int qlport_down_retry; extern int ql2xplogiabsentdevice; extern int ql2xloginretrycount; extern int ql2xfdmienable; -extern int ql2xmaxqdepth; extern int ql2xallocfwdump; extern int ql2xextended_error_logging; extern int ql2xiidmaenable; @@ -160,6 +159,9 @@ extern int qla83xx_clear_drv_presence(scsi_qla_host_t *vha); extern int __qla83xx_clear_drv_presence(scsi_qla_host_t *vha); extern int qla2x00_post_uevent_work(struct scsi_qla_host *, u32); +extern int qla2x00_post_uevent_work(struct scsi_qla_host *, u32); +extern void qla2x00_disable_board_on_pci_error(struct work_struct *); + /* * Global Functions in qla_mid.c source file. */ @@ -339,6 +341,11 @@ extern int qla2x00_system_error(scsi_qla_host_t *); extern int +qla2x00_write_serdes_word(scsi_qla_host_t *, uint16_t, uint16_t); +extern int +qla2x00_read_serdes_word(scsi_qla_host_t *, uint16_t, uint16_t *); + +extern int qla2x00_set_serdes_params(scsi_qla_host_t *, uint16_t, uint16_t, uint16_t); extern int @@ -455,6 +462,7 @@ extern uint8_t *qla25xx_read_nvram_data(scsi_qla_host_t *, uint8_t *, uint32_t, extern int qla25xx_write_nvram_data(scsi_qla_host_t *, uint8_t *, uint32_t, uint32_t); extern int qla2x00_is_a_vp_did(scsi_qla_host_t *, uint32_t); +bool qla2x00_check_reg_for_disconnect(scsi_qla_host_t *, uint32_t); extern int qla2x00_beacon_on(struct scsi_qla_host *); extern int qla2x00_beacon_off(struct scsi_qla_host *); @@ -541,10 +549,9 @@ struct fc_function_template; extern struct fc_function_template qla2xxx_transport_functions; extern struct fc_function_template qla2xxx_transport_vport_functions; extern void qla2x00_alloc_sysfs_attr(scsi_qla_host_t *); -extern void qla2x00_free_sysfs_attr(scsi_qla_host_t *); +extern void qla2x00_free_sysfs_attr(scsi_qla_host_t *, bool); extern void qla2x00_init_host_attr(scsi_qla_host_t *); extern void qla2x00_alloc_sysfs_attr(scsi_qla_host_t *); -extern void qla2x00_free_sysfs_attr(scsi_qla_host_t *); extern int qla2x00_loopback_test(scsi_qla_host_t *, struct msg_echo_lb *, uint16_t *); extern int qla2x00_echo_test(scsi_qla_host_t *, struct msg_echo_lb *, uint16_t *); @@ -725,7 +732,7 @@ extern inline void qla8044_set_qsnt_ready(struct scsi_qla_host *vha); extern inline void qla8044_need_reset_handler(struct scsi_qla_host *vha); extern int qla8044_device_state_handler(struct scsi_qla_host *vha); extern void qla8044_clear_qsnt_ready(struct scsi_qla_host *vha); -extern void qla8044_clear_drv_active(struct scsi_qla_host *vha); +extern void qla8044_clear_drv_active(struct qla_hw_data *); void qla8044_get_minidump(struct scsi_qla_host *vha); int qla8044_collect_md_data(struct scsi_qla_host *vha); extern int qla8044_md_get_template(scsi_qla_host_t *); diff --git a/drivers/scsi/qla2xxx/qla_init.c b/drivers/scsi/qla2xxx/qla_init.c index 03f715e7591..e7e5f4facf7 100644 --- a/drivers/scsi/qla2xxx/qla_init.c +++ b/drivers/scsi/qla2xxx/qla_init.c @@ -1694,6 +1694,8 @@ enable_82xx_npiv: if (!fw_major_version && ql2xallocfwdump && !(IS_P3P_TYPE(ha))) qla2x00_alloc_fw_dump(vha); + } else { + goto failed; } } else { ql_log(ql_log_fatal, vha, 0x00cd, diff --git a/drivers/scsi/qla2xxx/qla_inline.h b/drivers/scsi/qla2xxx/qla_inline.h index 957088b0461..ce8b5fb0f34 100644 --- a/drivers/scsi/qla2xxx/qla_inline.h +++ b/drivers/scsi/qla2xxx/qla_inline.h @@ -261,25 +261,6 @@ qla2x00_gid_list_size(struct qla_hw_data *ha) } static inline void -qla2x00_do_host_ramp_up(scsi_qla_host_t *vha) -{ - if (vha->hw->cfg_lun_q_depth >= ql2xmaxqdepth) - return; - - /* Wait at least HOST_QUEUE_RAMPDOWN_INTERVAL before ramping up */ - if (time_before(jiffies, (vha->hw->host_last_rampdown_time + - HOST_QUEUE_RAMPDOWN_INTERVAL))) - return; - - /* Wait at least HOST_QUEUE_RAMPUP_INTERVAL between each ramp up */ - if (time_before(jiffies, (vha->hw->host_last_rampup_time + - HOST_QUEUE_RAMPUP_INTERVAL))) - return; - - set_bit(HOST_RAMP_UP_QUEUE_DEPTH, &vha->dpc_flags); -} - -static inline void qla2x00_handle_mbx_completion(struct qla_hw_data *ha, int status) { if (test_bit(MBX_INTR_WAIT, &ha->mbx_cmd_flags) && diff --git a/drivers/scsi/qla2xxx/qla_isr.c b/drivers/scsi/qla2xxx/qla_isr.c index ff9c86b1a0d..9bc86b9e86b 100644 --- a/drivers/scsi/qla2xxx/qla_isr.c +++ b/drivers/scsi/qla2xxx/qla_isr.c @@ -56,6 +56,16 @@ qla2100_intr_handler(int irq, void *dev_id) vha = pci_get_drvdata(ha->pdev); for (iter = 50; iter--; ) { hccr = RD_REG_WORD(®->hccr); + /* Check for PCI disconnection */ + if (hccr == 0xffff) { + /* + * Schedule this on the default system workqueue so that + * all the adapter workqueues and the DPC thread can be + * shutdown cleanly. + */ + schedule_work(&ha->board_disable); + break; + } if (hccr & HCCR_RISC_PAUSE) { if (pci_channel_offline(ha->pdev)) break; @@ -110,6 +120,22 @@ qla2100_intr_handler(int irq, void *dev_id) return (IRQ_HANDLED); } +bool +qla2x00_check_reg_for_disconnect(scsi_qla_host_t *vha, uint32_t reg) +{ + /* Check for PCI disconnection */ + if (reg == 0xffffffff) { + /* + * Schedule this on the default system workqueue so that all the + * adapter workqueues and the DPC thread can be shutdown + * cleanly. + */ + schedule_work(&vha->hw->board_disable); + return true; + } else + return false; +} + /** * qla2300_intr_handler() - Process interrupts for the ISP23xx and ISP63xx. * @irq: @@ -148,11 +174,14 @@ qla2300_intr_handler(int irq, void *dev_id) vha = pci_get_drvdata(ha->pdev); for (iter = 50; iter--; ) { stat = RD_REG_DWORD(®->u.isp2300.host_status); + if (qla2x00_check_reg_for_disconnect(vha, stat)) + break; if (stat & HSR_RISC_PAUSED) { if (unlikely(pci_channel_offline(ha->pdev))) break; hccr = RD_REG_WORD(®->hccr); + if (hccr & (BIT_15 | BIT_13 | BIT_11 | BIT_8)) ql_log(ql_log_warn, vha, 0x5026, "Parity error -- HCCR=%x, Dumping " @@ -269,11 +298,18 @@ qla81xx_idc_event(scsi_qla_host_t *vha, uint16_t aen, uint16_t descr) { "Complete", "Request Notification", "Time Extension" }; int rval; struct device_reg_24xx __iomem *reg24 = &vha->hw->iobase->isp24; + struct device_reg_82xx __iomem *reg82 = &vha->hw->iobase->isp82; uint16_t __iomem *wptr; uint16_t cnt, timeout, mb[QLA_IDC_ACK_REGS]; /* Seed data -- mailbox1 -> mailbox7. */ - wptr = (uint16_t __iomem *)®24->mailbox1; + if (IS_QLA81XX(vha->hw) || IS_QLA83XX(vha->hw)) + wptr = (uint16_t __iomem *)®24->mailbox1; + else if (IS_QLA8044(vha->hw)) + wptr = (uint16_t __iomem *)®82->mailbox_out[1]; + else + return; + for (cnt = 0; cnt < QLA_IDC_ACK_REGS; cnt++, wptr++) mb[cnt] = RD_REG_WORD(wptr); @@ -287,7 +323,7 @@ qla81xx_idc_event(scsi_qla_host_t *vha, uint16_t aen, uint16_t descr) case MBA_IDC_COMPLETE: if (mb[1] >> 15) { vha->hw->flags.idc_compl_status = 1; - if (vha->hw->notify_dcbx_comp) + if (vha->hw->notify_dcbx_comp && !vha->vp_idx) complete(&vha->hw->dcbx_comp); } break; @@ -758,7 +794,7 @@ skip_rio: ql_dbg(ql_dbg_async, vha, 0x500d, "DCBX Completed -- %04x %04x %04x.\n", mb[1], mb[2], mb[3]); - if (ha->notify_dcbx_comp) + if (ha->notify_dcbx_comp && !vha->vp_idx) complete(&ha->dcbx_comp); } else @@ -1032,7 +1068,7 @@ skip_rio: } } case MBA_IDC_COMPLETE: - if (ha->notify_lb_portup_comp) + if (ha->notify_lb_portup_comp && !vha->vp_idx) complete(&ha->lb_portup_comp); /* Fallthru */ case MBA_IDC_TIME_EXT: @@ -1991,7 +2027,6 @@ qla2x00_status_entry(scsi_qla_host_t *vha, struct rsp_que *rsp, void *pkt) /* Fast path completion. */ if (comp_status == CS_COMPLETE && scsi_status == 0) { - qla2x00_do_host_ramp_up(vha); qla2x00_process_completed_request(vha, req, handle); return; @@ -2250,9 +2285,6 @@ out: cp->cmnd, scsi_bufflen(cp), rsp_info_len, resid_len, fw_resid_len); - if (!res) - qla2x00_do_host_ramp_up(vha); - if (rsp->status_srb == NULL) sp->done(ha, sp, res); } @@ -2575,6 +2607,8 @@ qla24xx_intr_handler(int irq, void *dev_id) vha = pci_get_drvdata(ha->pdev); for (iter = 50; iter--; ) { stat = RD_REG_DWORD(®->host_status); + if (qla2x00_check_reg_for_disconnect(vha, stat)) + break; if (stat & HSRX_RISC_PAUSED) { if (unlikely(pci_channel_offline(ha->pdev))) break; @@ -2644,6 +2678,7 @@ qla24xx_msix_rsp_q(int irq, void *dev_id) struct device_reg_24xx __iomem *reg; struct scsi_qla_host *vha; unsigned long flags; + uint32_t stat = 0; rsp = (struct rsp_que *) dev_id; if (!rsp) { @@ -2657,11 +2692,19 @@ qla24xx_msix_rsp_q(int irq, void *dev_id) spin_lock_irqsave(&ha->hardware_lock, flags); vha = pci_get_drvdata(ha->pdev); + /* + * Use host_status register to check to PCI disconnection before we + * we process the response queue. + */ + stat = RD_REG_DWORD(®->host_status); + if (qla2x00_check_reg_for_disconnect(vha, stat)) + goto out; qla24xx_process_response_queue(vha, rsp); if (!ha->flags.disable_msix_handshake) { WRT_REG_DWORD(®->hccr, HCCRX_CLR_RISC_INT); RD_REG_DWORD_RELAXED(®->hccr); } +out: spin_unlock_irqrestore(&ha->hardware_lock, flags); return IRQ_HANDLED; @@ -2671,9 +2714,11 @@ static irqreturn_t qla25xx_msix_rsp_q(int irq, void *dev_id) { struct qla_hw_data *ha; + scsi_qla_host_t *vha; struct rsp_que *rsp; struct device_reg_24xx __iomem *reg; unsigned long flags; + uint32_t hccr = 0; rsp = (struct rsp_que *) dev_id; if (!rsp) { @@ -2682,17 +2727,21 @@ qla25xx_msix_rsp_q(int irq, void *dev_id) return IRQ_NONE; } ha = rsp->hw; + vha = pci_get_drvdata(ha->pdev); /* Clear the interrupt, if enabled, for this response queue */ if (!ha->flags.disable_msix_handshake) { reg = &ha->iobase->isp24; spin_lock_irqsave(&ha->hardware_lock, flags); WRT_REG_DWORD(®->hccr, HCCRX_CLR_RISC_INT); - RD_REG_DWORD_RELAXED(®->hccr); + hccr = RD_REG_DWORD_RELAXED(®->hccr); spin_unlock_irqrestore(&ha->hardware_lock, flags); } + if (qla2x00_check_reg_for_disconnect(vha, hccr)) + goto out; queue_work_on((int) (rsp->id - 1), ha->wq, &rsp->q_work); +out: return IRQ_HANDLED; } @@ -2723,6 +2772,8 @@ qla24xx_msix_default(int irq, void *dev_id) vha = pci_get_drvdata(ha->pdev); do { stat = RD_REG_DWORD(®->host_status); + if (qla2x00_check_reg_for_disconnect(vha, stat)) + break; if (stat & HSRX_RISC_PAUSED) { if (unlikely(pci_channel_offline(ha->pdev))) break; @@ -2937,7 +2988,7 @@ msix_out: int qla2x00_request_irqs(struct qla_hw_data *ha, struct rsp_que *rsp) { - int ret; + int ret = QLA_FUNCTION_FAILED; device_reg_t __iomem *reg = ha->iobase; scsi_qla_host_t *vha = pci_get_drvdata(ha->pdev); @@ -2971,10 +3022,12 @@ qla2x00_request_irqs(struct qla_hw_data *ha, struct rsp_que *rsp) ha->chip_revision, ha->fw_attributes); goto clear_risc_ints; } - ql_log(ql_log_info, vha, 0x0037, - "MSI-X Falling back-to MSI mode -%d.\n", ret); + skip_msix: + ql_log(ql_log_info, vha, 0x0037, + "Falling back-to MSI mode -%d.\n", ret); + if (!IS_QLA24XX(ha) && !IS_QLA2532(ha) && !IS_QLA8432(ha) && !IS_QLA8001(ha) && !IS_P3P_TYPE(ha) && !IS_QLAFX00(ha)) goto skip_msi; @@ -2986,14 +3039,13 @@ skip_msix: ha->flags.msi_enabled = 1; } else ql_log(ql_log_warn, vha, 0x0039, - "MSI-X; Falling back-to INTa mode -- %d.\n", ret); + "Falling back-to INTa mode -- %d.\n", ret); +skip_msi: /* Skip INTx on ISP82xx. */ if (!ha->flags.msi_enabled && IS_QLA82XX(ha)) return QLA_FUNCTION_FAILED; -skip_msi: - ret = request_irq(ha->pdev->irq, ha->isp_ops->intr_handler, ha->flags.msi_enabled ? 0 : IRQF_SHARED, QLA2XXX_DRIVER_NAME, rsp); diff --git a/drivers/scsi/qla2xxx/qla_mbx.c b/drivers/scsi/qla2xxx/qla_mbx.c index a9aae500e79..b94511ae005 100644 --- a/drivers/scsi/qla2xxx/qla_mbx.c +++ b/drivers/scsi/qla2xxx/qla_mbx.c @@ -468,7 +468,7 @@ qla2x00_execute_fw(scsi_qla_host_t *vha, uint32_t risc_addr) mcp->mb[1] = MSW(risc_addr); mcp->mb[2] = LSW(risc_addr); mcp->mb[3] = 0; - if (IS_QLA81XX(ha) || IS_QLA83XX(ha)) { + if (IS_QLA25XX(ha) || IS_QLA81XX(ha) || IS_QLA83XX(ha)) { struct nvram_81xx *nv = ha->nvram; mcp->mb[4] = (nv->enhanced_features & EXTENDED_BB_CREDITS); @@ -1214,7 +1214,7 @@ qla2x00_init_firmware(scsi_qla_host_t *vha, uint16_t size) mcp->mb[6] = MSW(MSD(ha->init_cb_dma)); mcp->mb[7] = LSW(MSD(ha->init_cb_dma)); mcp->out_mb = MBX_7|MBX_6|MBX_3|MBX_2|MBX_1|MBX_0; - if ((IS_QLA81XX(ha) || IS_QLA83XX(ha)) && ha->ex_init_cb->ex_version) { + if (ha->ex_init_cb && ha->ex_init_cb->ex_version) { mcp->mb[1] = BIT_0; mcp->mb[10] = MSW(ha->ex_init_cb_dma); mcp->mb[11] = LSW(ha->ex_init_cb_dma); @@ -2800,6 +2800,75 @@ qla2x00_system_error(scsi_qla_host_t *vha) return rval; } +int +qla2x00_write_serdes_word(scsi_qla_host_t *vha, uint16_t addr, uint16_t data) +{ + int rval; + mbx_cmd_t mc; + mbx_cmd_t *mcp = &mc; + + if (!IS_QLA2031(vha->hw)) + return QLA_FUNCTION_FAILED; + + ql_dbg(ql_dbg_mbx + ql_dbg_verbose, vha, 0x1182, + "Entered %s.\n", __func__); + + mcp->mb[0] = MBC_WRITE_SERDES; + mcp->mb[1] = addr; + mcp->mb[2] = data & 0xff; + mcp->mb[3] = 0; + mcp->out_mb = MBX_3|MBX_2|MBX_1|MBX_0; + mcp->in_mb = MBX_0; + mcp->tov = MBX_TOV_SECONDS; + mcp->flags = 0; + rval = qla2x00_mailbox_command(vha, mcp); + + if (rval != QLA_SUCCESS) { + ql_dbg(ql_dbg_mbx, vha, 0x1183, + "Failed=%x mb[0]=%x.\n", rval, mcp->mb[0]); + } else { + ql_dbg(ql_dbg_mbx + ql_dbg_verbose, vha, 0x1184, + "Done %s.\n", __func__); + } + + return rval; +} + +int +qla2x00_read_serdes_word(scsi_qla_host_t *vha, uint16_t addr, uint16_t *data) +{ + int rval; + mbx_cmd_t mc; + mbx_cmd_t *mcp = &mc; + + if (!IS_QLA2031(vha->hw)) + return QLA_FUNCTION_FAILED; + + ql_dbg(ql_dbg_mbx + ql_dbg_verbose, vha, 0x1185, + "Entered %s.\n", __func__); + + mcp->mb[0] = MBC_READ_SERDES; + mcp->mb[1] = addr; + mcp->mb[3] = 0; + mcp->out_mb = MBX_3|MBX_1|MBX_0; + mcp->in_mb = MBX_1|MBX_0; + mcp->tov = MBX_TOV_SECONDS; + mcp->flags = 0; + rval = qla2x00_mailbox_command(vha, mcp); + + *data = mcp->mb[1] & 0xff; + + if (rval != QLA_SUCCESS) { + ql_dbg(ql_dbg_mbx, vha, 0x1186, + "Failed=%x mb[0]=%x.\n", rval, mcp->mb[0]); + } else { + ql_dbg(ql_dbg_mbx + ql_dbg_verbose, vha, 0x1187, + "Done %s.\n", __func__); + } + + return rval; +} + /** * qla2x00_set_serdes_params() - * @ha: HA context diff --git a/drivers/scsi/qla2xxx/qla_mr.c b/drivers/scsi/qla2xxx/qla_mr.c index 30d20e74e48..ba6f8b139c9 100644 --- a/drivers/scsi/qla2xxx/qla_mr.c +++ b/drivers/scsi/qla2xxx/qla_mr.c @@ -1610,6 +1610,22 @@ qlafx00_timer_routine(scsi_qla_host_t *vha) ha->mr.fw_critemp_timer_tick--; } } + if (ha->mr.host_info_resend) { + /* + * Incomplete host info might be sent to firmware + * durinng system boot - info should be resend + */ + if (ha->mr.hinfo_resend_timer_tick == 0) { + ha->mr.host_info_resend = false; + set_bit(FX00_HOST_INFO_RESEND, &vha->dpc_flags); + ha->mr.hinfo_resend_timer_tick = + QLAFX00_HINFO_RESEND_INTERVAL; + qla2xxx_wake_dpc(vha); + } else { + ha->mr.hinfo_resend_timer_tick--; + } + } + } /* @@ -1867,6 +1883,7 @@ qlafx00_fx_disc(scsi_qla_host_t *vha, fc_port_t *fcport, uint16_t fx_type) goto done_free_sp; } break; + case FXDISC_ABORT_IOCTL: default: break; } @@ -1888,6 +1905,8 @@ qlafx00_fx_disc(scsi_qla_host_t *vha, fc_port_t *fcport, uint16_t fx_type) p_sysid->sysname, SYSNAME_LENGTH); strncpy(phost_info->nodename, p_sysid->nodename, NODENAME_LENGTH); + if (!strcmp(phost_info->nodename, "(none)")) + ha->mr.host_info_resend = true; strncpy(phost_info->release, p_sysid->release, RELEASE_LENGTH); strncpy(phost_info->version, @@ -1948,8 +1967,8 @@ qlafx00_fx_disc(scsi_qla_host_t *vha, fc_port_t *fcport, uint16_t fx_type) if (fx_type == FXDISC_GET_CONFIG_INFO) { struct config_info_data *pinfo = (struct config_info_data *) fdisc->u.fxiocb.rsp_addr; - memcpy(&vha->hw->mr.product_name, pinfo->product_name, - sizeof(vha->hw->mr.product_name)); + strcpy(vha->hw->model_number, pinfo->model_num); + strcpy(vha->hw->model_desc, pinfo->model_description); memcpy(&vha->hw->mr.symbolic_name, pinfo->symbolic_name, sizeof(vha->hw->mr.symbolic_name)); memcpy(&vha->hw->mr.serial_num, pinfo->serial_num, @@ -1993,7 +2012,11 @@ qlafx00_fx_disc(scsi_qla_host_t *vha, fc_port_t *fcport, uint16_t fx_type) ql_dump_buffer(ql_dbg_init + ql_dbg_buffer, vha, 0x0146, (uint8_t *)pinfo, 16); memcpy(vha->hw->gid_list, pinfo, QLAFX00_TGT_NODE_LIST_SIZE); - } + } else if (fx_type == FXDISC_ABORT_IOCTL) + fdisc->u.fxiocb.result = + (fdisc->u.fxiocb.result == cpu_to_le32(0x68)) ? + cpu_to_le32(QLA_SUCCESS) : cpu_to_le32(QLA_FUNCTION_FAILED); + rval = le32_to_cpu(fdisc->u.fxiocb.result); done_unmap_dma: @@ -2092,6 +2115,10 @@ qlafx00_abort_command(srb_t *sp) /* Command not found. */ return QLA_FUNCTION_FAILED; } + if (sp->type == SRB_FXIOCB_DCMD) + return qlafx00_fx_disc(vha, &vha->hw->mr.fcport, + FXDISC_ABORT_IOCTL); + return qlafx00_async_abt_cmd(sp); } @@ -2419,7 +2446,6 @@ qlafx00_status_entry(scsi_qla_host_t *vha, struct rsp_que *rsp, void *pkt) /* Fast path completion. */ if (comp_status == CS_COMPLETE && scsi_status == 0) { - qla2x00_do_host_ramp_up(vha); qla2x00_process_completed_request(vha, req, handle); return; } @@ -2630,9 +2656,6 @@ check_scsi_status: rsp_info_len, resid_len, fw_resid_len, sense_len, par_sense_len, rsp_info_len); - if (!res) - qla2x00_do_host_ramp_up(vha); - if (rsp->status_srb == NULL) sp->done(ha, sp, res); } @@ -3021,6 +3044,8 @@ qlafx00_intr_handler(int irq, void *dev_id) vha = pci_get_drvdata(ha->pdev); for (iter = 50; iter--; clr_intr = 0) { stat = QLAFX00_RD_INTR_REG(ha); + if (qla2x00_check_reg_for_disconnect(vha, stat)) + break; if ((stat & QLAFX00_HST_INT_STS_BITS) == 0) break; diff --git a/drivers/scsi/qla2xxx/qla_mr.h b/drivers/scsi/qla2xxx/qla_mr.h index 79a93c52bae..6cd7072cc0f 100644 --- a/drivers/scsi/qla2xxx/qla_mr.h +++ b/drivers/scsi/qla2xxx/qla_mr.h @@ -304,7 +304,9 @@ struct register_host_info { #define QLAFX00_TGT_NODE_LIST_SIZE (sizeof(uint32_t) * 32) struct config_info_data { - uint8_t product_name[256]; + uint8_t model_num[16]; + uint8_t model_description[80]; + uint8_t reserved0[160]; uint8_t symbolic_name[64]; uint8_t serial_num[32]; uint8_t hw_version[16]; @@ -343,6 +345,7 @@ struct config_info_data { #define FXDISC_GET_TGT_NODE_INFO 0x80 #define FXDISC_GET_TGT_NODE_LIST 0x81 #define FXDISC_REG_HOST_INFO 0x99 +#define FXDISC_ABORT_IOCTL 0xff #define QLAFX00_HBA_ICNTRL_REG 0x20B08 #define QLAFX00_ICR_ENB_MASK 0x80000000 @@ -490,7 +493,6 @@ struct qla_mt_iocb_rsp_fx00 { #define FX00_DEF_RATOV 10 struct mr_data_fx00 { - uint8_t product_name[256]; uint8_t symbolic_name[64]; uint8_t serial_num[32]; uint8_t hw_version[16]; @@ -511,6 +513,8 @@ struct mr_data_fx00 { uint32_t old_aenmbx0_state; uint32_t critical_temperature; bool extended_io_enabled; + bool host_info_resend; + uint8_t hinfo_resend_timer_tick; }; #define QLAFX00_EXTENDED_IO_EN_MASK 0x20 @@ -537,7 +541,11 @@ struct mr_data_fx00 { #define QLAFX00_RESET_INTERVAL 120 /* number of seconds */ #define QLAFX00_MAX_RESET_INTERVAL 600 /* number of seconds */ #define QLAFX00_CRITEMP_INTERVAL 60 /* number of seconds */ +#define QLAFX00_HINFO_RESEND_INTERVAL 60 /* number of seconds */ #define QLAFX00_CRITEMP_THRSHLD 80 /* Celsius degrees */ +/* Max conncurrent IOs that can be queued */ +#define QLAFX00_MAX_CANQUEUE 1024 + #endif diff --git a/drivers/scsi/qla2xxx/qla_nx.c b/drivers/scsi/qla2xxx/qla_nx.c index 11ce53dcbe7..1e6ba4a369e 100644 --- a/drivers/scsi/qla2xxx/qla_nx.c +++ b/drivers/scsi/qla2xxx/qla_nx.c @@ -2096,6 +2096,7 @@ qla82xx_msix_default(int irq, void *dev_id) int status = 0; unsigned long flags; uint32_t stat = 0; + uint32_t host_int = 0; uint16_t mb[4]; rsp = (struct rsp_que *) dev_id; @@ -2111,7 +2112,10 @@ qla82xx_msix_default(int irq, void *dev_id) spin_lock_irqsave(&ha->hardware_lock, flags); vha = pci_get_drvdata(ha->pdev); do { - if (RD_REG_DWORD(®->host_int)) { + host_int = RD_REG_DWORD(®->host_int); + if (qla2x00_check_reg_for_disconnect(vha, host_int)) + break; + if (host_int) { stat = RD_REG_DWORD(®->host_status); switch (stat & 0xff) { @@ -2156,6 +2160,7 @@ qla82xx_msix_rsp_q(int irq, void *dev_id) struct rsp_que *rsp; struct device_reg_82xx __iomem *reg; unsigned long flags; + uint32_t host_int = 0; rsp = (struct rsp_que *) dev_id; if (!rsp) { @@ -2168,8 +2173,12 @@ qla82xx_msix_rsp_q(int irq, void *dev_id) reg = &ha->iobase->isp82; spin_lock_irqsave(&ha->hardware_lock, flags); vha = pci_get_drvdata(ha->pdev); + host_int = RD_REG_DWORD(®->host_int); + if (qla2x00_check_reg_for_disconnect(vha, host_int)) + goto out; qla24xx_process_response_queue(vha, rsp); WRT_REG_DWORD(®->host_int, 0); +out: spin_unlock_irqrestore(&ha->hardware_lock, flags); return IRQ_HANDLED; } @@ -2183,6 +2192,7 @@ qla82xx_poll(int irq, void *dev_id) struct device_reg_82xx __iomem *reg; int status = 0; uint32_t stat; + uint32_t host_int = 0; uint16_t mb[4]; unsigned long flags; @@ -2198,7 +2208,10 @@ qla82xx_poll(int irq, void *dev_id) spin_lock_irqsave(&ha->hardware_lock, flags); vha = pci_get_drvdata(ha->pdev); - if (RD_REG_DWORD(®->host_int)) { + host_int = RD_REG_DWORD(®->host_int); + if (qla2x00_check_reg_for_disconnect(vha, host_int)) + goto out; + if (host_int) { stat = RD_REG_DWORD(®->host_status); switch (stat & 0xff) { case 0x1: @@ -2224,8 +2237,9 @@ qla82xx_poll(int irq, void *dev_id) stat * 0xff); break; } + WRT_REG_DWORD(®->host_int, 0); } - WRT_REG_DWORD(®->host_int, 0); +out: spin_unlock_irqrestore(&ha->hardware_lock, flags); } @@ -3003,7 +3017,7 @@ qla8xxx_dev_failed_handler(scsi_qla_host_t *vha) qla82xx_clear_drv_active(ha); qla82xx_idc_unlock(ha); } else if (IS_QLA8044(ha)) { - qla8044_clear_drv_active(vha); + qla8044_clear_drv_active(ha); qla8044_idc_unlock(ha); } diff --git a/drivers/scsi/qla2xxx/qla_nx2.c b/drivers/scsi/qla2xxx/qla_nx2.c index 8164cc9e728..f60989d729a 100644 --- a/drivers/scsi/qla2xxx/qla_nx2.c +++ b/drivers/scsi/qla2xxx/qla_nx2.c @@ -1257,10 +1257,10 @@ exit_start_fw: } void -qla8044_clear_drv_active(struct scsi_qla_host *vha) +qla8044_clear_drv_active(struct qla_hw_data *ha) { uint32_t drv_active; - struct qla_hw_data *ha = vha->hw; + struct scsi_qla_host *vha = pci_get_drvdata(ha->pdev); drv_active = qla8044_rd_direct(vha, QLA8044_CRB_DRV_ACTIVE_INDEX); drv_active &= ~(1 << (ha->portnum)); @@ -1324,7 +1324,7 @@ qla8044_device_bootstrap(struct scsi_qla_host *vha) if (rval != QLA_SUCCESS) { ql_log(ql_log_info, vha, 0xb0b3, "%s: HW State: FAILED\n", __func__); - qla8044_clear_drv_active(vha); + qla8044_clear_drv_active(ha); qla8044_wr_direct(vha, QLA8044_CRB_DEV_STATE_INDEX, QLA8XXX_DEV_FAILED); return rval; @@ -1555,6 +1555,15 @@ qla8044_need_reset_handler(struct scsi_qla_host *vha) qla8044_idc_lock(ha); } + drv_state = qla8044_rd_direct(vha, + QLA8044_CRB_DRV_STATE_INDEX); + drv_active = qla8044_rd_direct(vha, + QLA8044_CRB_DRV_ACTIVE_INDEX); + + ql_log(ql_log_info, vha, 0xb0c5, + "%s(%ld): drv_state = 0x%x, drv_active = 0x%x\n", + __func__, vha->host_no, drv_state, drv_active); + if (!ha->flags.nic_core_reset_owner) { ql_dbg(ql_dbg_p3p, vha, 0xb0c3, "%s(%ld): reset acknowledged\n", @@ -1580,23 +1589,15 @@ qla8044_need_reset_handler(struct scsi_qla_host *vha) dev_state = qla8044_rd_direct(vha, QLA8044_CRB_DEV_STATE_INDEX); - } while (dev_state == QLA8XXX_DEV_NEED_RESET); + } while (((drv_state & drv_active) != drv_active) && + (dev_state == QLA8XXX_DEV_NEED_RESET)); } else { qla8044_set_rst_ready(vha); /* wait for 10 seconds for reset ack from all functions */ reset_timeout = jiffies + (ha->fcoe_reset_timeout * HZ); - drv_state = qla8044_rd_direct(vha, - QLA8044_CRB_DRV_STATE_INDEX); - drv_active = qla8044_rd_direct(vha, - QLA8044_CRB_DRV_ACTIVE_INDEX); - - ql_log(ql_log_info, vha, 0xb0c5, - "%s(%ld): drv_state = 0x%x, drv_active = 0x%x\n", - __func__, vha->host_no, drv_state, drv_active); - - while (drv_state != drv_active) { + while ((drv_state & drv_active) != drv_active) { if (time_after_eq(jiffies, reset_timeout)) { ql_log(ql_log_info, vha, 0xb0c6, "%s: RESET TIMEOUT!" @@ -1736,7 +1737,7 @@ qla8044_update_idc_reg(struct scsi_qla_host *vha) rval = qla8044_set_idc_ver(vha); if (rval == QLA_FUNCTION_FAILED) - qla8044_clear_drv_active(vha); + qla8044_clear_drv_active(ha); qla8044_idc_unlock(ha); exit_update_idc_reg: @@ -1859,7 +1860,7 @@ qla8044_device_state_handler(struct scsi_qla_host *vha) goto exit; case QLA8XXX_DEV_COLD: rval = qla8044_device_bootstrap(vha); - goto exit; + break; case QLA8XXX_DEV_INITIALIZING: qla8044_idc_unlock(ha); msleep(1000); @@ -2253,7 +2254,7 @@ qla8044_minidump_process_rdmem(struct scsi_qla_host *vha, if (r_addr & 0xf) { ql_dbg(ql_dbg_p3p, vha, 0xb0f1, - "[%s]: Read addr 0x%x not 16 bytes alligned\n", + "[%s]: Read addr 0x%x not 16 bytes aligned\n", __func__, r_addr); return QLA_FUNCTION_FAILED; } diff --git a/drivers/scsi/qla2xxx/qla_os.c b/drivers/scsi/qla2xxx/qla_os.c index 52be35e0300..89a53002b58 100644 --- a/drivers/scsi/qla2xxx/qla_os.c +++ b/drivers/scsi/qla2xxx/qla_os.c @@ -110,7 +110,8 @@ MODULE_PARM_DESC(ql2xfdmienable, "Enables FDMI registrations. " "0 - no FDMI. Default is 1 - perform FDMI."); -int ql2xmaxqdepth = MAX_Q_DEPTH; +#define MAX_Q_DEPTH 32 +static int ql2xmaxqdepth = MAX_Q_DEPTH; module_param(ql2xmaxqdepth, int, S_IRUGO|S_IWUSR); MODULE_PARM_DESC(ql2xmaxqdepth, "Maximum queue depth to set for each LUN. " @@ -728,10 +729,8 @@ qla2xxx_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd) } sp = qla2x00_get_sp(vha, fcport, GFP_ATOMIC); - if (!sp) { - set_bit(HOST_RAMP_DOWN_QUEUE_DEPTH, &vha->dpc_flags); + if (!sp) goto qc24_host_busy; - } sp->u.scmd.cmd = cmd; sp->type = SRB_SCSI_CMD; @@ -744,7 +743,6 @@ qla2xxx_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd) if (rval != QLA_SUCCESS) { ql_dbg(ql_dbg_io + ql_dbg_verbose, vha, 0x3013, "Start scsi failed rval=%d for cmd=%p.\n", rval, cmd); - set_bit(HOST_RAMP_DOWN_QUEUE_DEPTH, &vha->dpc_flags); goto qc24_host_busy_free_sp; } @@ -1474,81 +1472,6 @@ qla2x00_change_queue_type(struct scsi_device *sdev, int tag_type) return tag_type; } -static void -qla2x00_host_ramp_down_queuedepth(scsi_qla_host_t *vha) -{ - scsi_qla_host_t *vp; - struct Scsi_Host *shost; - struct scsi_device *sdev; - struct qla_hw_data *ha = vha->hw; - unsigned long flags; - - ha->host_last_rampdown_time = jiffies; - - if (ha->cfg_lun_q_depth <= vha->host->cmd_per_lun) - return; - - if ((ha->cfg_lun_q_depth / 2) < vha->host->cmd_per_lun) - ha->cfg_lun_q_depth = vha->host->cmd_per_lun; - else - ha->cfg_lun_q_depth = ha->cfg_lun_q_depth / 2; - - /* - * Geometrically ramp down the queue depth for all devices on this - * adapter - */ - spin_lock_irqsave(&ha->vport_slock, flags); - list_for_each_entry(vp, &ha->vp_list, list) { - shost = vp->host; - shost_for_each_device(sdev, shost) { - if (sdev->queue_depth > shost->cmd_per_lun) { - if (sdev->queue_depth < ha->cfg_lun_q_depth) - continue; - ql_dbg(ql_dbg_io, vp, 0x3031, - "%ld:%d:%d: Ramping down queue depth to %d", - vp->host_no, sdev->id, sdev->lun, - ha->cfg_lun_q_depth); - qla2x00_change_queue_depth(sdev, - ha->cfg_lun_q_depth, SCSI_QDEPTH_DEFAULT); - } - } - } - spin_unlock_irqrestore(&ha->vport_slock, flags); - - return; -} - -static void -qla2x00_host_ramp_up_queuedepth(scsi_qla_host_t *vha) -{ - scsi_qla_host_t *vp; - struct Scsi_Host *shost; - struct scsi_device *sdev; - struct qla_hw_data *ha = vha->hw; - unsigned long flags; - - ha->host_last_rampup_time = jiffies; - ha->cfg_lun_q_depth++; - - /* - * Linearly ramp up the queue depth for all devices on this - * adapter - */ - spin_lock_irqsave(&ha->vport_slock, flags); - list_for_each_entry(vp, &ha->vp_list, list) { - shost = vp->host; - shost_for_each_device(sdev, shost) { - if (sdev->queue_depth > ha->cfg_lun_q_depth) - continue; - qla2x00_change_queue_depth(sdev, ha->cfg_lun_q_depth, - SCSI_QDEPTH_RAMP_UP); - } - } - spin_unlock_irqrestore(&ha->vport_slock, flags); - - return; -} - /** * qla2x00_config_dma_addressing() - Configure OS DMA addressing method. * @ha: HA context @@ -2424,7 +2347,6 @@ qla2x00_probe_one(struct pci_dev *pdev, const struct pci_device_id *id) ha->init_cb_size = sizeof(init_cb_t); ha->link_data_rate = PORT_SPEED_UNKNOWN; ha->optrom_size = OPTROM_SIZE_2300; - ha->cfg_lun_q_depth = ql2xmaxqdepth; /* Assign ISP specific operations. */ if (IS_QLA2100(ha)) { @@ -2573,6 +2495,8 @@ qla2x00_probe_one(struct pci_dev *pdev, const struct pci_device_id *id) ha->mr.fw_reset_timer_tick = QLAFX00_RESET_INTERVAL; ha->mr.fw_critemp_timer_tick = QLAFX00_CRITEMP_INTERVAL; ha->mr.fw_hbt_en = 1; + ha->mr.host_info_resend = false; + ha->mr.hinfo_resend_timer_tick = QLAFX00_HINFO_RESEND_INTERVAL; } ql_dbg_pci(ql_dbg_init, pdev, 0x001e, @@ -2638,7 +2562,7 @@ qla2x00_probe_one(struct pci_dev *pdev, const struct pci_device_id *id) host = base_vha->host; base_vha->req = req; if (IS_QLAFX00(ha)) - host->can_queue = 1024; + host->can_queue = QLAFX00_MAX_CANQUEUE; else host->can_queue = req->length + 128; if (IS_QLA2XXX_MIDTYPE(ha)) @@ -2816,6 +2740,8 @@ que_init: */ qla2xxx_wake_dpc(base_vha); + INIT_WORK(&ha->board_disable, qla2x00_disable_board_on_pci_error); + if (IS_QLA8031(ha) || IS_MCTP_CAPABLE(ha)) { sprintf(wq_name, "qla2xxx_%lu_dpc_lp_wq", base_vha->host_no); ha->dpc_lp_wq = create_singlethread_workqueue(wq_name); @@ -2955,7 +2881,7 @@ probe_hw_failed: } if (IS_QLA8044(ha)) { qla8044_idc_lock(ha); - qla8044_clear_drv_active(base_vha); + qla8044_clear_drv_active(ha); qla8044_idc_unlock(ha); } iospace_config_failed: @@ -2980,22 +2906,6 @@ probe_out: } static void -qla2x00_stop_dpc_thread(scsi_qla_host_t *vha) -{ - struct qla_hw_data *ha = vha->hw; - struct task_struct *t = ha->dpc_thread; - - if (ha->dpc_thread == NULL) - return; - /* - * qla2xxx_wake_dpc checks for ->dpc_thread - * so we need to zero it out. - */ - ha->dpc_thread = NULL; - kthread_stop(t); -} - -static void qla2x00_shutdown(struct pci_dev *pdev) { scsi_qla_host_t *vha; @@ -3038,29 +2948,14 @@ qla2x00_shutdown(struct pci_dev *pdev) qla2x00_free_fw_dump(ha); } +/* Deletes all the virtual ports for a given ha */ static void -qla2x00_remove_one(struct pci_dev *pdev) +qla2x00_delete_all_vps(struct qla_hw_data *ha, scsi_qla_host_t *base_vha) { - scsi_qla_host_t *base_vha, *vha; - struct qla_hw_data *ha; + struct Scsi_Host *scsi_host; + scsi_qla_host_t *vha; unsigned long flags; - /* - * If the PCI device is disabled that means that probe failed and any - * resources should be have cleaned up on probe exit. - */ - if (!atomic_read(&pdev->enable_cnt)) - return; - - base_vha = pci_get_drvdata(pdev); - ha = base_vha->hw; - - ha->flags.host_shutting_down = 1; - - set_bit(UNLOADING, &base_vha->dpc_flags); - if (IS_QLAFX00(ha)) - qlafx00_driver_shutdown(base_vha, 20); - mutex_lock(&ha->vport_lock); while (ha->cur_vport_count) { spin_lock_irqsave(&ha->vport_slock, flags); @@ -3068,7 +2963,7 @@ qla2x00_remove_one(struct pci_dev *pdev) BUG_ON(base_vha->list.next == &ha->vp_list); /* This assumes first entry in ha->vp_list is always base vha */ vha = list_first_entry(&base_vha->list, scsi_qla_host_t, list); - scsi_host_get(vha->host); + scsi_host = scsi_host_get(vha->host); spin_unlock_irqrestore(&ha->vport_slock, flags); mutex_unlock(&ha->vport_lock); @@ -3079,27 +2974,12 @@ qla2x00_remove_one(struct pci_dev *pdev) mutex_lock(&ha->vport_lock); } mutex_unlock(&ha->vport_lock); +} - if (IS_QLA8031(ha)) { - ql_dbg(ql_dbg_p3p, base_vha, 0xb07e, - "Clearing fcoe driver presence.\n"); - if (qla83xx_clear_drv_presence(base_vha) != QLA_SUCCESS) - ql_dbg(ql_dbg_p3p, base_vha, 0xb079, - "Error while clearing DRV-Presence.\n"); - } - - qla2x00_abort_all_cmds(base_vha, DID_NO_CONNECT << 16); - - qla2x00_dfs_remove(base_vha); - - qla84xx_put_chip(base_vha); - - /* Disable timer */ - if (base_vha->timer_active) - qla2x00_stop_timer(base_vha); - - base_vha->flags.online = 0; - +/* Stops all deferred work threads */ +static void +qla2x00_destroy_deferred_work(struct qla_hw_data *ha) +{ /* Flush the work queue and remove it */ if (ha->wq) { flush_workqueue(ha->wq); @@ -3133,27 +3013,12 @@ qla2x00_remove_one(struct pci_dev *pdev) ha->dpc_thread = NULL; kthread_stop(t); } - qlt_remove_target(ha, base_vha); - - qla2x00_free_sysfs_attr(base_vha); - - fc_remove_host(base_vha->host); - - scsi_remove_host(base_vha->host); - - qla2x00_free_device(base_vha); - - scsi_host_put(base_vha->host); +} - if (IS_QLA8044(ha)) { - qla8044_idc_lock(ha); - qla8044_clear_drv_active(base_vha); - qla8044_idc_unlock(ha); - } +static void +qla2x00_unmap_iobases(struct qla_hw_data *ha) +{ if (IS_QLA82XX(ha)) { - qla82xx_idc_lock(ha); - qla82xx_clear_drv_active(ha); - qla82xx_idc_unlock(ha); iounmap((device_reg_t __iomem *)ha->nx_pcibase); if (!ql2xdbwr) @@ -3171,6 +3036,84 @@ qla2x00_remove_one(struct pci_dev *pdev) if (IS_QLA83XX(ha) && ha->msixbase) iounmap(ha->msixbase); } +} + +static void +qla2x00_clear_drv_active(scsi_qla_host_t *vha) +{ + struct qla_hw_data *ha = vha->hw; + + if (IS_QLA8044(ha)) { + qla8044_idc_lock(ha); + qla8044_clear_drv_active(ha); + qla8044_idc_unlock(ha); + } else if (IS_QLA82XX(ha)) { + qla82xx_idc_lock(ha); + qla82xx_clear_drv_active(ha); + qla82xx_idc_unlock(ha); + } +} + +static void +qla2x00_remove_one(struct pci_dev *pdev) +{ + scsi_qla_host_t *base_vha; + struct qla_hw_data *ha; + + /* + * If the PCI device is disabled that means that probe failed and any + * resources should be have cleaned up on probe exit. + */ + if (!atomic_read(&pdev->enable_cnt)) + return; + + base_vha = pci_get_drvdata(pdev); + ha = base_vha->hw; + + set_bit(UNLOADING, &base_vha->dpc_flags); + + if (IS_QLAFX00(ha)) + qlafx00_driver_shutdown(base_vha, 20); + + qla2x00_delete_all_vps(ha, base_vha); + + if (IS_QLA8031(ha)) { + ql_dbg(ql_dbg_p3p, base_vha, 0xb07e, + "Clearing fcoe driver presence.\n"); + if (qla83xx_clear_drv_presence(base_vha) != QLA_SUCCESS) + ql_dbg(ql_dbg_p3p, base_vha, 0xb079, + "Error while clearing DRV-Presence.\n"); + } + + qla2x00_abort_all_cmds(base_vha, DID_NO_CONNECT << 16); + + qla2x00_dfs_remove(base_vha); + + qla84xx_put_chip(base_vha); + + /* Disable timer */ + if (base_vha->timer_active) + qla2x00_stop_timer(base_vha); + + base_vha->flags.online = 0; + + qla2x00_destroy_deferred_work(ha); + + qlt_remove_target(ha, base_vha); + + qla2x00_free_sysfs_attr(base_vha, true); + + fc_remove_host(base_vha->host); + + scsi_remove_host(base_vha->host); + + qla2x00_free_device(base_vha); + + scsi_host_put(base_vha->host); + + qla2x00_clear_drv_active(base_vha); + + qla2x00_unmap_iobases(ha); pci_release_selected_regions(ha->pdev, ha->bars); kfree(ha); @@ -3192,9 +3135,8 @@ qla2x00_free_device(scsi_qla_host_t *vha) if (vha->timer_active) qla2x00_stop_timer(vha); - qla2x00_stop_dpc_thread(vha); - qla25xx_delete_queues(vha); + if (ha->flags.fce_enabled) qla2x00_disable_fce_trace(vha, NULL, NULL); @@ -4731,6 +4673,66 @@ exit: return rval; } +void +qla2x00_disable_board_on_pci_error(struct work_struct *work) +{ + struct qla_hw_data *ha = container_of(work, struct qla_hw_data, + board_disable); + struct pci_dev *pdev = ha->pdev; + scsi_qla_host_t *base_vha = pci_get_drvdata(ha->pdev); + + ql_log(ql_log_warn, base_vha, 0x015b, + "Disabling adapter.\n"); + + set_bit(UNLOADING, &base_vha->dpc_flags); + + qla2x00_delete_all_vps(ha, base_vha); + + qla2x00_abort_all_cmds(base_vha, DID_NO_CONNECT << 16); + + qla2x00_dfs_remove(base_vha); + + qla84xx_put_chip(base_vha); + + if (base_vha->timer_active) + qla2x00_stop_timer(base_vha); + + base_vha->flags.online = 0; + + qla2x00_destroy_deferred_work(ha); + + /* + * Do not try to stop beacon blink as it will issue a mailbox + * command. + */ + qla2x00_free_sysfs_attr(base_vha, false); + + fc_remove_host(base_vha->host); + + scsi_remove_host(base_vha->host); + + base_vha->flags.init_done = 0; + qla25xx_delete_queues(base_vha); + qla2x00_free_irqs(base_vha); + qla2x00_free_fcports(base_vha); + qla2x00_mem_free(ha); + qla82xx_md_free(base_vha); + qla2x00_free_queues(ha); + + scsi_host_put(base_vha->host); + + qla2x00_unmap_iobases(ha); + + pci_release_selected_regions(ha->pdev, ha->bars); + kfree(ha); + ha = NULL; + + pci_disable_pcie_error_reporting(pdev); + pci_disable_device(pdev); + pci_set_drvdata(pdev, NULL); + +} + /************************************************************************** * qla2x00_do_dpc * This kernel thread is a task that is schedule by the interrupt handler @@ -4863,6 +4865,14 @@ qla2x00_do_dpc(void *data) ql_dbg(ql_dbg_dpc, base_vha, 0x401f, "ISPFx00 Target Scan End\n"); } + if (test_and_clear_bit(FX00_HOST_INFO_RESEND, + &base_vha->dpc_flags)) { + ql_dbg(ql_dbg_dpc, base_vha, 0x4023, + "ISPFx00 Host Info resend scheduled\n"); + qlafx00_fx_disc(base_vha, + &base_vha->hw->mr.fcport, + FXDISC_REG_HOST_INFO); + } } if (test_and_clear_bit(ISP_ABORT_NEEDED, @@ -4990,17 +5000,6 @@ loop_resync_check: qla2xxx_flash_npiv_conf(base_vha); } - if (test_and_clear_bit(HOST_RAMP_DOWN_QUEUE_DEPTH, - &base_vha->dpc_flags)) { - /* Prevents simultaneous ramp up and down */ - clear_bit(HOST_RAMP_UP_QUEUE_DEPTH, - &base_vha->dpc_flags); - qla2x00_host_ramp_down_queuedepth(base_vha); - } - - if (test_and_clear_bit(HOST_RAMP_UP_QUEUE_DEPTH, - &base_vha->dpc_flags)) - qla2x00_host_ramp_up_queuedepth(base_vha); intr_on_check: if (!ha->interrupts_on) ha->isp_ops->enable_intrs(ha); @@ -5095,9 +5094,20 @@ qla2x00_timer(scsi_qla_host_t *vha) return; } - /* Hardware read to raise pending EEH errors during mailbox waits. */ - if (!pci_channel_offline(ha->pdev)) + /* + * Hardware read to raise pending EEH errors during mailbox waits. If + * the read returns -1 then disable the board. + */ + if (!pci_channel_offline(ha->pdev)) { pci_read_config_word(ha->pdev, PCI_VENDOR_ID, &w); + if (w == 0xffff) + /* + * Schedule this on the default system workqueue so that + * all the adapter workqueues and the DPC thread can be + * shutdown cleanly. + */ + schedule_work(&ha->board_disable); + } /* Make sure qla82xx_watchdog is run only for physical port */ if (!vha->vp_idx && IS_P3P_TYPE(ha)) { @@ -5182,7 +5192,6 @@ qla2x00_timer(scsi_qla_host_t *vha) "Loop down - seconds remaining %d.\n", atomic_read(&vha->loop_down_timer)); } - /* Check if beacon LED needs to be blinked for physical host only */ if (!vha->vp_idx && (ha->beacon_blink_led == 1)) { /* There is no beacon_blink function for ISP82xx */ @@ -5206,9 +5215,7 @@ qla2x00_timer(scsi_qla_host_t *vha) test_bit(ISP_UNRECOVERABLE, &vha->dpc_flags) || test_bit(FCOE_CTX_RESET_NEEDED, &vha->dpc_flags) || test_bit(VP_DPC_NEEDED, &vha->dpc_flags) || - test_bit(RELOGIN_NEEDED, &vha->dpc_flags) || - test_bit(HOST_RAMP_DOWN_QUEUE_DEPTH, &vha->dpc_flags) || - test_bit(HOST_RAMP_UP_QUEUE_DEPTH, &vha->dpc_flags))) { + test_bit(RELOGIN_NEEDED, &vha->dpc_flags))) { ql_dbg(ql_dbg_timer, vha, 0x600b, "isp_abort_needed=%d loop_resync_needed=%d " "fcport_update_needed=%d start_dpc=%d " @@ -5221,15 +5228,12 @@ qla2x00_timer(scsi_qla_host_t *vha) ql_dbg(ql_dbg_timer, vha, 0x600c, "beacon_blink_needed=%d isp_unrecoverable=%d " "fcoe_ctx_reset_needed=%d vp_dpc_needed=%d " - "relogin_needed=%d, host_ramp_down_needed=%d " - "host_ramp_up_needed=%d.\n", + "relogin_needed=%d.\n", test_bit(BEACON_BLINK_NEEDED, &vha->dpc_flags), test_bit(ISP_UNRECOVERABLE, &vha->dpc_flags), test_bit(FCOE_CTX_RESET_NEEDED, &vha->dpc_flags), test_bit(VP_DPC_NEEDED, &vha->dpc_flags), - test_bit(RELOGIN_NEEDED, &vha->dpc_flags), - test_bit(HOST_RAMP_UP_QUEUE_DEPTH, &vha->dpc_flags), - test_bit(HOST_RAMP_DOWN_QUEUE_DEPTH, &vha->dpc_flags)); + test_bit(RELOGIN_NEEDED, &vha->dpc_flags)); qla2xxx_wake_dpc(vha); } diff --git a/drivers/scsi/qla2xxx/qla_target.c b/drivers/scsi/qla2xxx/qla_target.c index 38a1257e76e..2eb97d7e8d1 100644 --- a/drivers/scsi/qla2xxx/qla_target.c +++ b/drivers/scsi/qla2xxx/qla_target.c @@ -590,7 +590,7 @@ static struct qla_tgt_sess *qlt_create_sess( /* Check to avoid double sessions */ spin_lock_irqsave(&ha->hardware_lock, flags); - list_for_each_entry(sess, &ha->tgt.qla_tgt->sess_list, + list_for_each_entry(sess, &vha->vha_tgt.qla_tgt->sess_list, sess_list_entry) { if (!memcmp(sess->port_name, fcport->port_name, WWN_SIZE)) { ql_dbg(ql_dbg_tgt_mgt, vha, 0xf005, @@ -627,7 +627,7 @@ static struct qla_tgt_sess *qlt_create_sess( return NULL; } - sess->tgt = ha->tgt.qla_tgt; + sess->tgt = vha->vha_tgt.qla_tgt; sess->vha = vha; sess->s_id = fcport->d_id; sess->loop_id = fcport->loop_id; @@ -635,7 +635,7 @@ static struct qla_tgt_sess *qlt_create_sess( ql_dbg(ql_dbg_tgt_mgt, vha, 0xf006, "Adding sess %p to tgt %p via ->check_initiator_node_acl()\n", - sess, ha->tgt.qla_tgt); + sess, vha->vha_tgt.qla_tgt); be_sid[0] = sess->s_id.b.domain; be_sid[1] = sess->s_id.b.area; @@ -662,8 +662,8 @@ static struct qla_tgt_sess *qlt_create_sess( memcpy(sess->port_name, fcport->port_name, sizeof(sess->port_name)); spin_lock_irqsave(&ha->hardware_lock, flags); - list_add_tail(&sess->sess_list_entry, &ha->tgt.qla_tgt->sess_list); - ha->tgt.qla_tgt->sess_count++; + list_add_tail(&sess->sess_list_entry, &vha->vha_tgt.qla_tgt->sess_list); + vha->vha_tgt.qla_tgt->sess_count++; spin_unlock_irqrestore(&ha->hardware_lock, flags); ql_dbg(ql_dbg_tgt_mgt, vha, 0xf04b, @@ -682,7 +682,7 @@ static struct qla_tgt_sess *qlt_create_sess( void qlt_fc_port_added(struct scsi_qla_host *vha, fc_port_t *fcport) { struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; struct qla_tgt_sess *sess; unsigned long flags; @@ -692,6 +692,9 @@ void qlt_fc_port_added(struct scsi_qla_host *vha, fc_port_t *fcport) if (!tgt || (fcport->port_type != FCT_INITIATOR)) return; + if (qla_ini_mode_enabled(vha)) + return; + spin_lock_irqsave(&ha->hardware_lock, flags); if (tgt->tgt_stop) { spin_unlock_irqrestore(&ha->hardware_lock, flags); @@ -701,9 +704,9 @@ void qlt_fc_port_added(struct scsi_qla_host *vha, fc_port_t *fcport) if (!sess) { spin_unlock_irqrestore(&ha->hardware_lock, flags); - mutex_lock(&ha->tgt.tgt_mutex); + mutex_lock(&vha->vha_tgt.tgt_mutex); sess = qlt_create_sess(vha, fcport, false); - mutex_unlock(&ha->tgt.tgt_mutex); + mutex_unlock(&vha->vha_tgt.tgt_mutex); spin_lock_irqsave(&ha->hardware_lock, flags); } else { @@ -739,7 +742,7 @@ void qlt_fc_port_added(struct scsi_qla_host *vha, fc_port_t *fcport) void qlt_fc_port_deleted(struct scsi_qla_host *vha, fc_port_t *fcport) { struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; struct qla_tgt_sess *sess; unsigned long flags; @@ -806,12 +809,12 @@ void qlt_stop_phase1(struct qla_tgt *tgt) * Mutex needed to sync with qla_tgt_fc_port_[added,deleted]. * Lock is needed, because we still can get an incoming packet. */ - mutex_lock(&ha->tgt.tgt_mutex); + mutex_lock(&vha->vha_tgt.tgt_mutex); spin_lock_irqsave(&ha->hardware_lock, flags); tgt->tgt_stop = 1; qlt_clear_tgt_db(tgt, true); spin_unlock_irqrestore(&ha->hardware_lock, flags); - mutex_unlock(&ha->tgt.tgt_mutex); + mutex_unlock(&vha->vha_tgt.tgt_mutex); flush_delayed_work(&tgt->sess_del_work); @@ -845,20 +848,21 @@ EXPORT_SYMBOL(qlt_stop_phase1); void qlt_stop_phase2(struct qla_tgt *tgt) { struct qla_hw_data *ha = tgt->ha; + scsi_qla_host_t *vha = pci_get_drvdata(ha->pdev); unsigned long flags; if (tgt->tgt_stopped) { - ql_dbg(ql_dbg_tgt_mgt, tgt->vha, 0xf04f, + ql_dbg(ql_dbg_tgt_mgt, vha, 0xf04f, "Already in tgt->tgt_stopped state\n"); dump_stack(); return; } - ql_dbg(ql_dbg_tgt_mgt, tgt->vha, 0xf00b, + ql_dbg(ql_dbg_tgt_mgt, vha, 0xf00b, "Waiting for %d IRQ commands to complete (tgt %p)", tgt->irq_cmd_count, tgt); - mutex_lock(&ha->tgt.tgt_mutex); + mutex_lock(&vha->vha_tgt.tgt_mutex); spin_lock_irqsave(&ha->hardware_lock, flags); while (tgt->irq_cmd_count != 0) { spin_unlock_irqrestore(&ha->hardware_lock, flags); @@ -868,9 +872,9 @@ void qlt_stop_phase2(struct qla_tgt *tgt) tgt->tgt_stop = 0; tgt->tgt_stopped = 1; spin_unlock_irqrestore(&ha->hardware_lock, flags); - mutex_unlock(&ha->tgt.tgt_mutex); + mutex_unlock(&vha->vha_tgt.tgt_mutex); - ql_dbg(ql_dbg_tgt_mgt, tgt->vha, 0xf00c, "Stop of tgt %p finished", + ql_dbg(ql_dbg_tgt_mgt, vha, 0xf00c, "Stop of tgt %p finished", tgt); } EXPORT_SYMBOL(qlt_stop_phase2); @@ -878,14 +882,14 @@ EXPORT_SYMBOL(qlt_stop_phase2); /* Called from qlt_remove_target() -> qla2x00_remove_one() */ static void qlt_release(struct qla_tgt *tgt) { - struct qla_hw_data *ha = tgt->ha; + scsi_qla_host_t *vha = tgt->vha; - if ((ha->tgt.qla_tgt != NULL) && !tgt->tgt_stopped) + if ((vha->vha_tgt.qla_tgt != NULL) && !tgt->tgt_stopped) qlt_stop_phase2(tgt); - ha->tgt.qla_tgt = NULL; + vha->vha_tgt.qla_tgt = NULL; - ql_dbg(ql_dbg_tgt_mgt, tgt->vha, 0xf00d, + ql_dbg(ql_dbg_tgt_mgt, vha, 0xf00d, "Release of tgt %p finished\n", tgt); kfree(tgt); @@ -949,8 +953,8 @@ static void qlt_send_notify_ack(struct scsi_qla_host *vha, return; } - if (ha->tgt.qla_tgt != NULL) - ha->tgt.qla_tgt->notify_ack_expected++; + if (vha->vha_tgt.qla_tgt != NULL) + vha->vha_tgt.qla_tgt->notify_ack_expected++; pkt->entry_type = NOTIFY_ACK_TYPE; pkt->entry_count = 1; @@ -1054,7 +1058,7 @@ static void qlt_24xx_send_abts_resp(struct scsi_qla_host *vha, /* Other bytes are zero */ } - ha->tgt.qla_tgt->abts_resp_expected++; + vha->vha_tgt.qla_tgt->abts_resp_expected++; qla2x00_start_iocbs(vha, vha->req); } @@ -1206,7 +1210,7 @@ static void qlt_24xx_handle_abts(struct scsi_qla_host *vha, ql_dbg(ql_dbg_tgt_mgt, vha, 0xf012, "qla_target(%d): task abort for non-existant session\n", vha->vp_idx); - rc = qlt_sched_sess_work(ha->tgt.qla_tgt, + rc = qlt_sched_sess_work(vha->vha_tgt.qla_tgt, QLA_TGT_SESS_WORK_ABORT, abts, sizeof(*abts)); if (rc != 0) { qlt_24xx_send_abts_resp(vha, abts, FCP_TMF_REJECTED, @@ -2157,8 +2161,7 @@ static int qlt_prepare_srr_ctio(struct scsi_qla_host *vha, struct qla_tgt_cmd *cmd, void *ctio) { struct qla_tgt_srr_ctio *sc; - struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; struct qla_tgt_srr_imm *imm; tgt->ctio_srr_id++; @@ -2474,7 +2477,7 @@ static void qlt_do_work(struct work_struct *work) struct qla_tgt_cmd *cmd = container_of(work, struct qla_tgt_cmd, work); scsi_qla_host_t *vha = cmd->vha; struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; struct qla_tgt_sess *sess = NULL; struct atio_from_isp *atio = &cmd->atio; unsigned char *cdb; @@ -2507,10 +2510,10 @@ static void qlt_do_work(struct work_struct *work) goto out_term; } - mutex_lock(&ha->tgt.tgt_mutex); + mutex_lock(&vha->vha_tgt.tgt_mutex); sess = qlt_make_local_sess(vha, s_id); /* sess has an extra creation ref. */ - mutex_unlock(&ha->tgt.tgt_mutex); + mutex_unlock(&vha->vha_tgt.tgt_mutex); if (!sess) goto out_term; @@ -2576,8 +2579,7 @@ out_term: static int qlt_handle_cmd_for_atio(struct scsi_qla_host *vha, struct atio_from_isp *atio) { - struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; struct qla_tgt_cmd *cmd; if (unlikely(tgt->tgt_stop)) { @@ -2593,11 +2595,9 @@ static int qlt_handle_cmd_for_atio(struct scsi_qla_host *vha, return -ENOMEM; } - INIT_LIST_HEAD(&cmd->cmd_list); - memcpy(&cmd->atio, atio, sizeof(*atio)); cmd->state = QLA_TGT_STATE_NEW; - cmd->tgt = ha->tgt.qla_tgt; + cmd->tgt = vha->vha_tgt.qla_tgt; cmd->vha = vha; INIT_WORK(&cmd->work, qlt_do_work); @@ -2723,7 +2723,7 @@ static int qlt_handle_task_mgmt(struct scsi_qla_host *vha, void *iocb) uint32_t lun, unpacked_lun; int lun_size, fn; - tgt = ha->tgt.qla_tgt; + tgt = vha->vha_tgt.qla_tgt; lun = a->u.isp24.fcp_cmnd.lun; lun_size = sizeof(a->u.isp24.fcp_cmnd.lun); @@ -2797,7 +2797,7 @@ static int qlt_abort_task(struct scsi_qla_host *vha, ql_dbg(ql_dbg_tgt_mgt, vha, 0xf025, "qla_target(%d): task abort for unexisting " "session\n", vha->vp_idx); - return qlt_sched_sess_work(ha->tgt.qla_tgt, + return qlt_sched_sess_work(vha->vha_tgt.qla_tgt, QLA_TGT_SESS_WORK_ABORT, iocb, sizeof(*iocb)); } @@ -2810,7 +2810,6 @@ static int qlt_abort_task(struct scsi_qla_host *vha, static int qlt_24xx_handle_els(struct scsi_qla_host *vha, struct imm_ntfy_from_isp *iocb) { - struct qla_hw_data *ha = vha->hw; int res = 0; ql_dbg(ql_dbg_tgt_mgt, vha, 0xf026, @@ -2828,7 +2827,7 @@ static int qlt_24xx_handle_els(struct scsi_qla_host *vha, case ELS_PDISC: case ELS_ADISC: { - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; if (tgt->link_reinit_iocb_pending) { qlt_send_notify_ack(vha, &tgt->link_reinit_iocb, 0, 0, 0, 0, 0, 0); @@ -3202,8 +3201,7 @@ static void qlt_prepare_srr_imm(struct scsi_qla_host *vha, struct imm_ntfy_from_isp *iocb) { struct qla_tgt_srr_imm *imm; - struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; struct qla_tgt_srr_ctio *sctio; tgt->imm_srr_id++; @@ -3313,7 +3311,7 @@ static void qlt_handle_imm_notify(struct scsi_qla_host *vha, case IMM_NTFY_LIP_LINK_REINIT: { - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; ql_dbg(ql_dbg_tgt_mgt, vha, 0xf033, "qla_target(%d): LINK REINIT (loop %#x, " "subcode %x)\n", vha->vp_idx, @@ -3489,7 +3487,7 @@ static void qlt_24xx_atio_pkt(struct scsi_qla_host *vha, struct atio_from_isp *atio) { struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; int rc; if (unlikely(tgt == NULL)) { @@ -3591,7 +3589,7 @@ static void qlt_24xx_atio_pkt(struct scsi_qla_host *vha, static void qlt_response_pkt(struct scsi_qla_host *vha, response_t *pkt) { struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; if (unlikely(tgt == NULL)) { ql_dbg(ql_dbg_tgt, vha, 0xe05d, @@ -3794,7 +3792,7 @@ void qlt_async_event(uint16_t code, struct scsi_qla_host *vha, uint16_t *mailbox) { struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; int login_code; ql_dbg(ql_dbg_tgt, vha, 0xe039, @@ -3924,14 +3922,14 @@ static fc_port_t *qlt_get_port_database(struct scsi_qla_host *vha, static struct qla_tgt_sess *qlt_make_local_sess(struct scsi_qla_host *vha, uint8_t *s_id) { - struct qla_hw_data *ha = vha->hw; struct qla_tgt_sess *sess = NULL; fc_port_t *fcport = NULL; int rc, global_resets; uint16_t loop_id = 0; retry: - global_resets = atomic_read(&ha->tgt.qla_tgt->tgt_global_resets_count); + global_resets = + atomic_read(&vha->vha_tgt.qla_tgt->tgt_global_resets_count); rc = qla24xx_get_loop_id(vha, s_id, &loop_id); if (rc != 0) { @@ -3958,12 +3956,13 @@ retry: return NULL; if (global_resets != - atomic_read(&ha->tgt.qla_tgt->tgt_global_resets_count)) { + atomic_read(&vha->vha_tgt.qla_tgt->tgt_global_resets_count)) { ql_dbg(ql_dbg_tgt_mgt, vha, 0xf043, "qla_target(%d): global reset during session discovery " "(counter was %d, new %d), retrying", vha->vp_idx, global_resets, - atomic_read(&ha->tgt.qla_tgt->tgt_global_resets_count)); + atomic_read(&vha->vha_tgt. + qla_tgt->tgt_global_resets_count)); goto retry; } @@ -3998,10 +3997,10 @@ static void qlt_abort_work(struct qla_tgt *tgt, if (!sess) { spin_unlock_irqrestore(&ha->hardware_lock, flags); - mutex_lock(&ha->tgt.tgt_mutex); + mutex_lock(&vha->vha_tgt.tgt_mutex); sess = qlt_make_local_sess(vha, s_id); /* sess has got an extra creation ref */ - mutex_unlock(&ha->tgt.tgt_mutex); + mutex_unlock(&vha->vha_tgt.tgt_mutex); spin_lock_irqsave(&ha->hardware_lock, flags); if (!sess) @@ -4052,10 +4051,10 @@ static void qlt_tmr_work(struct qla_tgt *tgt, if (!sess) { spin_unlock_irqrestore(&ha->hardware_lock, flags); - mutex_lock(&ha->tgt.tgt_mutex); + mutex_lock(&vha->vha_tgt.tgt_mutex); sess = qlt_make_local_sess(vha, s_id); /* sess has got an extra creation ref */ - mutex_unlock(&ha->tgt.tgt_mutex); + mutex_unlock(&vha->vha_tgt.tgt_mutex); spin_lock_irqsave(&ha->hardware_lock, flags); if (!sess) @@ -4141,9 +4140,9 @@ int qlt_add_target(struct qla_hw_data *ha, struct scsi_qla_host *base_vha) } ql_dbg(ql_dbg_tgt, base_vha, 0xe03b, - "Registering target for host %ld(%p)", base_vha->host_no, ha); + "Registering target for host %ld(%p).\n", base_vha->host_no, ha); - BUG_ON((ha->tgt.qla_tgt != NULL) || (ha->tgt.tgt_ops != NULL)); + BUG_ON(base_vha->vha_tgt.qla_tgt != NULL); tgt = kzalloc(sizeof(struct qla_tgt), GFP_KERNEL); if (!tgt) { @@ -4171,7 +4170,7 @@ int qlt_add_target(struct qla_hw_data *ha, struct scsi_qla_host *base_vha) INIT_WORK(&tgt->srr_work, qlt_handle_srr_work); atomic_set(&tgt->tgt_global_resets_count, 0); - ha->tgt.qla_tgt = tgt; + base_vha->vha_tgt.qla_tgt = tgt; ql_dbg(ql_dbg_tgt, base_vha, 0xe067, "qla_target(%d): using 64 Bit PCI addressing", @@ -4192,16 +4191,16 @@ int qlt_add_target(struct qla_hw_data *ha, struct scsi_qla_host *base_vha) /* Must be called under tgt_host_action_mutex */ int qlt_remove_target(struct qla_hw_data *ha, struct scsi_qla_host *vha) { - if (!ha->tgt.qla_tgt) + if (!vha->vha_tgt.qla_tgt) return 0; mutex_lock(&qla_tgt_mutex); - list_del(&ha->tgt.qla_tgt->tgt_list_entry); + list_del(&vha->vha_tgt.qla_tgt->tgt_list_entry); mutex_unlock(&qla_tgt_mutex); ql_dbg(ql_dbg_tgt, vha, 0xe03c, "Unregistering target for host %ld(%p)", vha->host_no, ha); - qlt_release(ha->tgt.qla_tgt); + qlt_release(vha->vha_tgt.qla_tgt); return 0; } @@ -4235,8 +4234,9 @@ static void qlt_lport_dump(struct scsi_qla_host *vha, u64 wwpn, * @callback: lport initialization callback for tcm_qla2xxx code * @target_lport_ptr: pointer for tcm_qla2xxx specific lport data */ -int qlt_lport_register(struct qla_tgt_func_tmpl *qla_tgt_ops, u64 wwpn, - int (*callback)(struct scsi_qla_host *), void *target_lport_ptr) +int qlt_lport_register(void *target_lport_ptr, u64 phys_wwpn, + u64 npiv_wwpn, u64 npiv_wwnn, + int (*callback)(struct scsi_qla_host *, void *, u64, u64)) { struct qla_tgt *tgt; struct scsi_qla_host *vha; @@ -4255,14 +4255,11 @@ int qlt_lport_register(struct qla_tgt_func_tmpl *qla_tgt_ops, u64 wwpn, if (!host) continue; - if (ha->tgt.tgt_ops != NULL) - continue; - if (!(host->hostt->supported_mode & MODE_TARGET)) continue; spin_lock_irqsave(&ha->hardware_lock, flags); - if (host->active_mode & MODE_TARGET) { + if ((!npiv_wwpn || !npiv_wwnn) && host->active_mode & MODE_TARGET) { pr_debug("MODE_TARGET already active on qla2xxx(%d)\n", host->host_no); spin_unlock_irqrestore(&ha->hardware_lock, flags); @@ -4276,24 +4273,18 @@ int qlt_lport_register(struct qla_tgt_func_tmpl *qla_tgt_ops, u64 wwpn, " qla2xxx scsi_host\n"); continue; } - qlt_lport_dump(vha, wwpn, b); + qlt_lport_dump(vha, phys_wwpn, b); if (memcmp(vha->port_name, b, WWN_SIZE)) { scsi_host_put(host); continue; } - /* - * Setup passed parameters ahead of invoking callback - */ - ha->tgt.tgt_ops = qla_tgt_ops; - ha->tgt.target_lport_ptr = target_lport_ptr; - rc = (*callback)(vha); - if (rc != 0) { - ha->tgt.tgt_ops = NULL; - ha->tgt.target_lport_ptr = NULL; - scsi_host_put(host); - } mutex_unlock(&qla_tgt_mutex); + + rc = (*callback)(vha, target_lport_ptr, npiv_wwpn, npiv_wwnn); + if (rc != 0) + scsi_host_put(host); + return rc; } mutex_unlock(&qla_tgt_mutex); @@ -4314,7 +4305,7 @@ void qlt_lport_deregister(struct scsi_qla_host *vha) /* * Clear the target_lport_ptr qla_target_template pointer in qla_hw_data */ - ha->tgt.target_lport_ptr = NULL; + vha->vha_tgt.target_lport_ptr = NULL; ha->tgt.tgt_ops = NULL; /* * Release the Scsi_Host reference for the underlying qla2xxx host @@ -4376,8 +4367,9 @@ void qlt_enable_vha(struct scsi_qla_host *vha) { struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; unsigned long flags; + scsi_qla_host_t *base_vha = pci_get_drvdata(ha->pdev); if (!tgt) { ql_dbg(ql_dbg_tgt, vha, 0xe069, @@ -4392,9 +4384,14 @@ qlt_enable_vha(struct scsi_qla_host *vha) qlt_set_mode(vha); spin_unlock_irqrestore(&ha->hardware_lock, flags); - set_bit(ISP_ABORT_NEEDED, &vha->dpc_flags); - qla2xxx_wake_dpc(vha); - qla2x00_wait_for_hba_online(vha); + if (vha->vp_idx) { + qla24xx_disable_vp(vha); + qla24xx_enable_vp(vha); + } else { + set_bit(ISP_ABORT_NEEDED, &base_vha->dpc_flags); + qla2xxx_wake_dpc(base_vha); + qla2x00_wait_for_hba_online(base_vha); + } } EXPORT_SYMBOL(qlt_enable_vha); @@ -4407,7 +4404,7 @@ void qlt_disable_vha(struct scsi_qla_host *vha) { struct qla_hw_data *ha = vha->hw; - struct qla_tgt *tgt = ha->tgt.qla_tgt; + struct qla_tgt *tgt = vha->vha_tgt.qla_tgt; unsigned long flags; if (!tgt) { @@ -4438,8 +4435,10 @@ qlt_vport_create(struct scsi_qla_host *vha, struct qla_hw_data *ha) if (!qla_tgt_mode_enabled(vha)) return; - mutex_init(&ha->tgt.tgt_mutex); - mutex_init(&ha->tgt.tgt_host_action_mutex); + vha->vha_tgt.qla_tgt = NULL; + + mutex_init(&vha->vha_tgt.tgt_mutex); + mutex_init(&vha->vha_tgt.tgt_host_action_mutex); qlt_clear_mode(vha); @@ -4450,6 +4449,8 @@ qlt_vport_create(struct scsi_qla_host *vha, struct qla_hw_data *ha) * assigning the value appropriately. */ ha->tgt.atio_q_length = ATIO_ENTRY_CNT_24XX; + + qlt_add_target(ha, vha); } void @@ -4768,8 +4769,8 @@ qlt_probe_one_stage1(struct scsi_qla_host *base_vha, struct qla_hw_data *ha) ISP_ATIO_Q_OUT(base_vha) = &ha->iobase->isp24.atio_q_out; } - mutex_init(&ha->tgt.tgt_mutex); - mutex_init(&ha->tgt.tgt_host_action_mutex); + mutex_init(&base_vha->vha_tgt.tgt_mutex); + mutex_init(&base_vha->vha_tgt.tgt_host_action_mutex); qlt_clear_mode(base_vha); } diff --git a/drivers/scsi/qla2xxx/qla_target.h b/drivers/scsi/qla2xxx/qla_target.h index b33e411f28a..66e755cdde5 100644 --- a/drivers/scsi/qla2xxx/qla_target.h +++ b/drivers/scsi/qla2xxx/qla_target.h @@ -855,7 +855,6 @@ struct qla_tgt_cmd { uint16_t loop_id; /* to save extra sess dereferences */ struct qla_tgt *tgt; /* to save extra sess dereferences */ struct scsi_qla_host *vha; - struct list_head cmd_list; struct atio_from_isp atio; }; @@ -932,8 +931,8 @@ void qlt_disable_vha(struct scsi_qla_host *); */ extern int qlt_add_target(struct qla_hw_data *, struct scsi_qla_host *); extern int qlt_remove_target(struct qla_hw_data *, struct scsi_qla_host *); -extern int qlt_lport_register(struct qla_tgt_func_tmpl *, u64, - int (*callback)(struct scsi_qla_host *), void *); +extern int qlt_lport_register(void *, u64, u64, u64, + int (*callback)(struct scsi_qla_host *, void *, u64, u64)); extern void qlt_lport_deregister(struct scsi_qla_host *); extern void qlt_unreg_sess(struct qla_tgt_sess *); extern void qlt_fc_port_added(struct scsi_qla_host *, fc_port_t *); diff --git a/drivers/scsi/qla2xxx/qla_version.h b/drivers/scsi/qla2xxx/qla_version.h index a808e293dae..31d19535b01 100644 --- a/drivers/scsi/qla2xxx/qla_version.h +++ b/drivers/scsi/qla2xxx/qla_version.h @@ -7,7 +7,7 @@ /* * Driver version */ -#define QLA2XXX_VERSION "8.06.00.08-k" +#define QLA2XXX_VERSION "8.06.00.12-k" #define QLA_DRIVER_MAJOR_VER 8 #define QLA_DRIVER_MINOR_VER 6 diff --git a/drivers/scsi/qla2xxx/tcm_qla2xxx.c b/drivers/scsi/qla2xxx/tcm_qla2xxx.c index 7eb19be35d4..75a141bbe74 100644 --- a/drivers/scsi/qla2xxx/tcm_qla2xxx.c +++ b/drivers/scsi/qla2xxx/tcm_qla2xxx.c @@ -53,16 +53,6 @@ struct workqueue_struct *tcm_qla2xxx_free_wq; struct workqueue_struct *tcm_qla2xxx_cmd_wq; -static int tcm_qla2xxx_check_true(struct se_portal_group *se_tpg) -{ - return 1; -} - -static int tcm_qla2xxx_check_false(struct se_portal_group *se_tpg) -{ - return 0; -} - /* * Parse WWN. * If strict, we require lower-case hex and colon separators to be sure @@ -174,7 +164,7 @@ static int tcm_qla2xxx_npiv_parse_wwn( *wwnn = 0; /* count may include a LF at end of string */ - if (name[cnt-1] == '\n') + if (name[cnt-1] == '\n' || name[cnt-1] == 0) cnt--; /* validate we have enough characters for WWPN */ @@ -777,6 +767,9 @@ static void tcm_qla2xxx_put_session(struct se_session *se_sess) static void tcm_qla2xxx_put_sess(struct qla_tgt_sess *sess) { + if (!sess) + return; + assert_spin_locked(&sess->vha->hw->hardware_lock); kref_put(&sess->se_sess->sess_kref, tcm_qla2xxx_release_session); } @@ -957,7 +950,6 @@ static ssize_t tcm_qla2xxx_tpg_store_enable( struct tcm_qla2xxx_lport *lport = container_of(se_wwn, struct tcm_qla2xxx_lport, lport_wwn); struct scsi_qla_host *vha = lport->qla_vha; - struct qla_hw_data *ha = vha->hw; struct tcm_qla2xxx_tpg *tpg = container_of(se_tpg, struct tcm_qla2xxx_tpg, se_tpg); unsigned long op; @@ -977,12 +969,12 @@ static ssize_t tcm_qla2xxx_tpg_store_enable( atomic_set(&tpg->lport_tpg_enabled, 1); qlt_enable_vha(vha); } else { - if (!ha->tgt.qla_tgt) { - pr_err("truct qla_hw_data *ha->tgt.qla_tgt is NULL\n"); + if (!vha->vha_tgt.qla_tgt) { + pr_err("struct qla_hw_data *vha->vha_tgt.qla_tgt is NULL\n"); return -ENODEV; } atomic_set(&tpg->lport_tpg_enabled, 0); - qlt_stop_phase1(ha->tgt.qla_tgt); + qlt_stop_phase1(vha->vha_tgt.qla_tgt); } return count; @@ -1011,7 +1003,7 @@ static struct se_portal_group *tcm_qla2xxx_make_tpg( if (kstrtoul(name + 5, 10, &tpgt) || tpgt > USHRT_MAX) return ERR_PTR(-EINVAL); - if (!lport->qla_npiv_vp && (tpgt != 1)) { + if ((tpgt != 1)) { pr_err("In non NPIV mode, a single TPG=1 is used for HW port mappings\n"); return ERR_PTR(-ENOSYS); } @@ -1038,11 +1030,8 @@ static struct se_portal_group *tcm_qla2xxx_make_tpg( kfree(tpg); return NULL; } - /* - * Setup local TPG=1 pointer for non NPIV mode. - */ - if (lport->qla_npiv_vp == NULL) - lport->tpg_1 = tpg; + + lport->tpg_1 = tpg; return &tpg->se_tpg; } @@ -1053,19 +1042,17 @@ static void tcm_qla2xxx_drop_tpg(struct se_portal_group *se_tpg) struct tcm_qla2xxx_tpg, se_tpg); struct tcm_qla2xxx_lport *lport = tpg->lport; struct scsi_qla_host *vha = lport->qla_vha; - struct qla_hw_data *ha = vha->hw; /* * Call into qla2x_target.c LLD logic to shutdown the active * FC Nexuses and disable target mode operation for this qla_hw_data */ - if (ha->tgt.qla_tgt && !ha->tgt.qla_tgt->tgt_stop) - qlt_stop_phase1(ha->tgt.qla_tgt); + if (vha->vha_tgt.qla_tgt && !vha->vha_tgt.qla_tgt->tgt_stop) + qlt_stop_phase1(vha->vha_tgt.qla_tgt); core_tpg_deregister(se_tpg); /* * Clear local TPG=1 pointer for non NPIV mode. */ - if (lport->qla_npiv_vp == NULL) lport->tpg_1 = NULL; kfree(tpg); @@ -1095,12 +1082,22 @@ static struct se_portal_group *tcm_qla2xxx_npiv_make_tpg( tpg->lport = lport; tpg->lport_tpgt = tpgt; + /* + * By default allow READ-ONLY TPG demo-mode access w/ cached dynamic + * NodeACLs + */ + tpg->tpg_attrib.generate_node_acls = 1; + tpg->tpg_attrib.demo_mode_write_protect = 1; + tpg->tpg_attrib.cache_dynamic_acls = 1; + tpg->tpg_attrib.demo_mode_login_only = 1; + ret = core_tpg_register(&tcm_qla2xxx_npiv_fabric_configfs->tf_ops, wwn, &tpg->se_tpg, tpg, TRANSPORT_TPG_TYPE_NORMAL); if (ret < 0) { kfree(tpg); return NULL; } + lport->tpg_1 = tpg; return &tpg->se_tpg; } @@ -1111,13 +1108,12 @@ static struct qla_tgt_sess *tcm_qla2xxx_find_sess_by_s_id( scsi_qla_host_t *vha, const uint8_t *s_id) { - struct qla_hw_data *ha = vha->hw; struct tcm_qla2xxx_lport *lport; struct se_node_acl *se_nacl; struct tcm_qla2xxx_nacl *nacl; u32 key; - lport = ha->tgt.target_lport_ptr; + lport = vha->vha_tgt.target_lport_ptr; if (!lport) { pr_err("Unable to locate struct tcm_qla2xxx_lport\n"); dump_stack(); @@ -1221,13 +1217,12 @@ static struct qla_tgt_sess *tcm_qla2xxx_find_sess_by_loop_id( scsi_qla_host_t *vha, const uint16_t loop_id) { - struct qla_hw_data *ha = vha->hw; struct tcm_qla2xxx_lport *lport; struct se_node_acl *se_nacl; struct tcm_qla2xxx_nacl *nacl; struct tcm_qla2xxx_fc_loopid *fc_loopid; - lport = ha->tgt.target_lport_ptr; + lport = vha->vha_tgt.target_lport_ptr; if (!lport) { pr_err("Unable to locate struct tcm_qla2xxx_lport\n"); dump_stack(); @@ -1341,6 +1336,7 @@ static void tcm_qla2xxx_free_session(struct qla_tgt_sess *sess) { struct qla_tgt *tgt = sess->tgt; struct qla_hw_data *ha = tgt->ha; + scsi_qla_host_t *vha = pci_get_drvdata(ha->pdev); struct se_session *se_sess; struct se_node_acl *se_nacl; struct tcm_qla2xxx_lport *lport; @@ -1357,7 +1353,7 @@ static void tcm_qla2xxx_free_session(struct qla_tgt_sess *sess) se_nacl = se_sess->se_node_acl; nacl = container_of(se_nacl, struct tcm_qla2xxx_nacl, se_node_acl); - lport = ha->tgt.target_lport_ptr; + lport = vha->vha_tgt.target_lport_ptr; if (!lport) { pr_err("Unable to locate struct tcm_qla2xxx_lport\n"); dump_stack(); @@ -1391,7 +1387,7 @@ static int tcm_qla2xxx_check_initiator_node_acl( unsigned char port_name[36]; unsigned long flags; - lport = ha->tgt.target_lport_ptr; + lport = vha->vha_tgt.target_lport_ptr; if (!lport) { pr_err("Unable to locate struct tcm_qla2xxx_lport\n"); dump_stack(); @@ -1455,7 +1451,8 @@ static void tcm_qla2xxx_update_sess(struct qla_tgt_sess *sess, port_id_t s_id, { struct qla_tgt *tgt = sess->tgt; struct qla_hw_data *ha = tgt->ha; - struct tcm_qla2xxx_lport *lport = ha->tgt.target_lport_ptr; + scsi_qla_host_t *vha = pci_get_drvdata(ha->pdev); + struct tcm_qla2xxx_lport *lport = vha->vha_tgt.target_lport_ptr; struct se_node_acl *se_nacl = sess->se_sess->se_node_acl; struct tcm_qla2xxx_nacl *nacl = container_of(se_nacl, struct tcm_qla2xxx_nacl, se_node_acl); @@ -1562,15 +1559,18 @@ static int tcm_qla2xxx_init_lport(struct tcm_qla2xxx_lport *lport) return 0; } -static int tcm_qla2xxx_lport_register_cb(struct scsi_qla_host *vha) +static int tcm_qla2xxx_lport_register_cb(struct scsi_qla_host *vha, + void *target_lport_ptr, + u64 npiv_wwpn, u64 npiv_wwnn) { struct qla_hw_data *ha = vha->hw; - struct tcm_qla2xxx_lport *lport; + struct tcm_qla2xxx_lport *lport = + (struct tcm_qla2xxx_lport *)target_lport_ptr; /* - * Setup local pointer to vha, NPIV VP pointer (if present) and - * vha->tcm_lport pointer + * Setup tgt_ops, local pointer to vha and target_lport_ptr */ - lport = (struct tcm_qla2xxx_lport *)ha->tgt.target_lport_ptr; + ha->tgt.tgt_ops = &tcm_qla2xxx_template; + vha->vha_tgt.target_lport_ptr = target_lport_ptr; lport->qla_vha = vha; return 0; @@ -1602,8 +1602,8 @@ static struct se_wwn *tcm_qla2xxx_make_lport( if (ret != 0) goto out; - ret = qlt_lport_register(&tcm_qla2xxx_template, wwpn, - tcm_qla2xxx_lport_register_cb, lport); + ret = qlt_lport_register(lport, wwpn, 0, 0, + tcm_qla2xxx_lport_register_cb); if (ret != 0) goto out_lport; @@ -1621,7 +1621,6 @@ static void tcm_qla2xxx_drop_lport(struct se_wwn *wwn) struct tcm_qla2xxx_lport *lport = container_of(wwn, struct tcm_qla2xxx_lport, lport_wwn); struct scsi_qla_host *vha = lport->qla_vha; - struct qla_hw_data *ha = vha->hw; struct se_node_acl *node; u32 key = 0; @@ -1630,8 +1629,8 @@ static void tcm_qla2xxx_drop_lport(struct se_wwn *wwn) * shutdown of struct qla_tgt after the call to * qlt_stop_phase1() from tcm_qla2xxx_drop_tpg() above.. */ - if (ha->tgt.qla_tgt && !ha->tgt.qla_tgt->tgt_stopped) - qlt_stop_phase2(ha->tgt.qla_tgt); + if (vha->vha_tgt.qla_tgt && !vha->vha_tgt.qla_tgt->tgt_stopped) + qlt_stop_phase2(vha->vha_tgt.qla_tgt); qlt_lport_deregister(vha); @@ -1642,17 +1641,70 @@ static void tcm_qla2xxx_drop_lport(struct se_wwn *wwn) kfree(lport); } +static int tcm_qla2xxx_lport_register_npiv_cb(struct scsi_qla_host *base_vha, + void *target_lport_ptr, + u64 npiv_wwpn, u64 npiv_wwnn) +{ + struct fc_vport *vport; + struct Scsi_Host *sh = base_vha->host; + struct scsi_qla_host *npiv_vha; + struct tcm_qla2xxx_lport *lport = + (struct tcm_qla2xxx_lport *)target_lport_ptr; + struct fc_vport_identifiers vport_id; + + if (!qla_tgt_mode_enabled(base_vha)) { + pr_err("qla2xxx base_vha not enabled for target mode\n"); + return -EPERM; + } + + memset(&vport_id, 0, sizeof(vport_id)); + vport_id.port_name = npiv_wwpn; + vport_id.node_name = npiv_wwnn; + vport_id.roles = FC_PORT_ROLE_FCP_INITIATOR; + vport_id.vport_type = FC_PORTTYPE_NPIV; + vport_id.disable = false; + + vport = fc_vport_create(sh, 0, &vport_id); + if (!vport) { + pr_err("fc_vport_create failed for qla2xxx_npiv\n"); + return -ENODEV; + } + /* + * Setup local pointer to NPIV vhba + target_lport_ptr + */ + npiv_vha = (struct scsi_qla_host *)vport->dd_data; + npiv_vha->vha_tgt.target_lport_ptr = target_lport_ptr; + lport->qla_vha = npiv_vha; + + scsi_host_get(npiv_vha->host); + return 0; +} + + static struct se_wwn *tcm_qla2xxx_npiv_make_lport( struct target_fabric_configfs *tf, struct config_group *group, const char *name) { struct tcm_qla2xxx_lport *lport; - u64 npiv_wwpn, npiv_wwnn; + u64 phys_wwpn, npiv_wwpn, npiv_wwnn; + char *p, tmp[128]; int ret; - if (tcm_qla2xxx_npiv_parse_wwn(name, strlen(name)+1, - &npiv_wwpn, &npiv_wwnn) < 0) + snprintf(tmp, 128, "%s", name); + + p = strchr(tmp, '@'); + if (!p) { + pr_err("Unable to locate NPIV '@' seperator\n"); + return ERR_PTR(-EINVAL); + } + *p++ = '\0'; + + if (tcm_qla2xxx_parse_wwn(tmp, &phys_wwpn, 1) < 0) + return ERR_PTR(-EINVAL); + + if (tcm_qla2xxx_npiv_parse_wwn(p, strlen(p)+1, + &npiv_wwpn, &npiv_wwnn) < 0) return ERR_PTR(-EINVAL); lport = kzalloc(sizeof(struct tcm_qla2xxx_lport), GFP_KERNEL); @@ -1666,12 +1718,19 @@ static struct se_wwn *tcm_qla2xxx_npiv_make_lport( TCM_QLA2XXX_NAMELEN, npiv_wwpn, npiv_wwnn); sprintf(lport->lport_naa_name, "naa.%016llx", (unsigned long long) npiv_wwpn); -/* FIXME: tcm_qla2xxx_npiv_make_lport */ - ret = -ENOSYS; + ret = tcm_qla2xxx_init_lport(lport); if (ret != 0) goto out; + ret = qlt_lport_register(lport, phys_wwpn, npiv_wwpn, npiv_wwnn, + tcm_qla2xxx_lport_register_npiv_cb); + if (ret != 0) + goto out_lport; + return &lport->lport_wwn; +out_lport: + vfree(lport->lport_loopid_map); + btree_destroy32(&lport->lport_fcport_map); out: kfree(lport); return ERR_PTR(ret); @@ -1681,14 +1740,16 @@ static void tcm_qla2xxx_npiv_drop_lport(struct se_wwn *wwn) { struct tcm_qla2xxx_lport *lport = container_of(wwn, struct tcm_qla2xxx_lport, lport_wwn); - struct scsi_qla_host *vha = lport->qla_vha; - struct Scsi_Host *sh = vha->host; + struct scsi_qla_host *npiv_vha = lport->qla_vha; + struct qla_hw_data *ha = npiv_vha->hw; + scsi_qla_host_t *base_vha = pci_get_drvdata(ha->pdev); + + scsi_host_put(npiv_vha->host); /* - * Notify libfc that we want to release the lport->npiv_vport + * Notify libfc that we want to release the vha->fc_vport */ - fc_vport_terminate(lport->npiv_vport); - - scsi_host_put(sh); + fc_vport_terminate(npiv_vha->fc_vport); + scsi_host_put(base_vha->host); kfree(lport); } @@ -1769,14 +1830,16 @@ static struct target_core_fabric_ops tcm_qla2xxx_npiv_ops = { .tpg_get_pr_transport_id = tcm_qla2xxx_get_pr_transport_id, .tpg_get_pr_transport_id_len = tcm_qla2xxx_get_pr_transport_id_len, .tpg_parse_pr_out_transport_id = tcm_qla2xxx_parse_pr_out_transport_id, - .tpg_check_demo_mode = tcm_qla2xxx_check_false, - .tpg_check_demo_mode_cache = tcm_qla2xxx_check_true, - .tpg_check_demo_mode_write_protect = tcm_qla2xxx_check_true, - .tpg_check_prod_mode_write_protect = tcm_qla2xxx_check_false, + .tpg_check_demo_mode = tcm_qla2xxx_check_demo_mode, + .tpg_check_demo_mode_cache = tcm_qla2xxx_check_demo_mode_cache, + .tpg_check_demo_mode_write_protect = tcm_qla2xxx_check_demo_mode, + .tpg_check_prod_mode_write_protect = + tcm_qla2xxx_check_prod_write_protect, .tpg_check_demo_mode_login_only = tcm_qla2xxx_check_demo_mode_login_only, .tpg_alloc_fabric_acl = tcm_qla2xxx_alloc_fabric_acl, .tpg_release_fabric_acl = tcm_qla2xxx_release_fabric_acl, .tpg_get_inst_index = tcm_qla2xxx_tpg_get_inst_index, + .check_stop_free = tcm_qla2xxx_check_stop_free, .release_cmd = tcm_qla2xxx_release_cmd, .put_session = tcm_qla2xxx_put_session, .shutdown_session = tcm_qla2xxx_shutdown_session, @@ -1871,7 +1934,8 @@ static int tcm_qla2xxx_register_configfs(void) * Setup default attribute lists for various npiv_fabric->tf_cit_tmpl */ npiv_fabric->tf_cit_tmpl.tfc_wwn_cit.ct_attrs = tcm_qla2xxx_wwn_attrs; - npiv_fabric->tf_cit_tmpl.tfc_tpg_base_cit.ct_attrs = NULL; + npiv_fabric->tf_cit_tmpl.tfc_tpg_base_cit.ct_attrs = + tcm_qla2xxx_tpg_attrs; npiv_fabric->tf_cit_tmpl.tfc_tpg_attrib_cit.ct_attrs = NULL; npiv_fabric->tf_cit_tmpl.tfc_tpg_param_cit.ct_attrs = NULL; npiv_fabric->tf_cit_tmpl.tfc_tpg_np_base_cit.ct_attrs = NULL; diff --git a/drivers/scsi/qla2xxx/tcm_qla2xxx.h b/drivers/scsi/qla2xxx/tcm_qla2xxx.h index 771f7b81644..275d8b9a7a3 100644 --- a/drivers/scsi/qla2xxx/tcm_qla2xxx.h +++ b/drivers/scsi/qla2xxx/tcm_qla2xxx.h @@ -70,12 +70,8 @@ struct tcm_qla2xxx_lport { struct tcm_qla2xxx_fc_loopid *lport_loopid_map; /* Pointer to struct scsi_qla_host from qla2xxx LLD */ struct scsi_qla_host *qla_vha; - /* Pointer to struct scsi_qla_host for NPIV VP from qla2xxx LLD */ - struct scsi_qla_host *qla_npiv_vp; /* Pointer to struct qla_tgt pointer */ struct qla_tgt lport_qla_tgt; - /* Pointer to struct fc_vport for NPIV vport from libfc */ - struct fc_vport *npiv_vport; /* Pointer to TPG=1 for non NPIV mode */ struct tcm_qla2xxx_tpg *tpg_1; /* Returned by tcm_qla2xxx_make_lport() */ diff --git a/drivers/scsi/qla4xxx/ql4_83xx.c b/drivers/scsi/qla4xxx/ql4_83xx.c index 8196c2f7915..919284834ad 100644 --- a/drivers/scsi/qla4xxx/ql4_83xx.c +++ b/drivers/scsi/qla4xxx/ql4_83xx.c @@ -465,7 +465,7 @@ int qla4_83xx_drv_lock(struct scsi_qla_host *ha) } /* Recovery Failed, some other function * has the lock, wait for 2secs and retry */ - ql4_printk(KERN_INFO, ha, "%s: IDC lock Recovery by %d failed, Retrying timout\n", + ql4_printk(KERN_INFO, ha, "%s: IDC lock Recovery by %d failed, Retrying timeout\n", __func__, ha->func_num); timeout = 0; } diff --git a/drivers/scsi/qla4xxx/ql4_bsg.c b/drivers/scsi/qla4xxx/ql4_bsg.c index cf8fdf1d125..04a0027dbca 100644 --- a/drivers/scsi/qla4xxx/ql4_bsg.c +++ b/drivers/scsi/qla4xxx/ql4_bsg.c @@ -446,6 +446,363 @@ leave: return rval; } +static void ql4xxx_execute_diag_cmd(struct bsg_job *bsg_job) +{ + struct Scsi_Host *host = iscsi_job_to_shost(bsg_job); + struct scsi_qla_host *ha = to_qla_host(host); + struct iscsi_bsg_request *bsg_req = bsg_job->request; + struct iscsi_bsg_reply *bsg_reply = bsg_job->reply; + uint8_t *rsp_ptr = NULL; + uint32_t mbox_cmd[MBOX_REG_COUNT]; + uint32_t mbox_sts[MBOX_REG_COUNT]; + int status = QLA_ERROR; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: in\n", __func__)); + + if (test_bit(DPC_RESET_HA, &ha->dpc_flags)) { + ql4_printk(KERN_INFO, ha, "%s: Adapter reset in progress. Invalid Request\n", + __func__); + bsg_reply->result = DID_ERROR << 16; + goto exit_diag_mem_test; + } + + bsg_reply->reply_payload_rcv_len = 0; + memcpy(mbox_cmd, &bsg_req->rqst_data.h_vendor.vendor_cmd[1], + sizeof(uint32_t) * MBOX_REG_COUNT); + + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: mbox_cmd: %08X %08X %08X %08X %08X %08X %08X %08X\n", + __func__, mbox_cmd[0], mbox_cmd[1], mbox_cmd[2], + mbox_cmd[3], mbox_cmd[4], mbox_cmd[5], mbox_cmd[6], + mbox_cmd[7])); + + status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 8, &mbox_cmd[0], + &mbox_sts[0]); + + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: mbox_sts: %08X %08X %08X %08X %08X %08X %08X %08X\n", + __func__, mbox_sts[0], mbox_sts[1], mbox_sts[2], + mbox_sts[3], mbox_sts[4], mbox_sts[5], mbox_sts[6], + mbox_sts[7])); + + if (status == QLA_SUCCESS) + bsg_reply->result = DID_OK << 16; + else + bsg_reply->result = DID_ERROR << 16; + + /* Send mbox_sts to application */ + bsg_job->reply_len = sizeof(struct iscsi_bsg_reply) + sizeof(mbox_sts); + rsp_ptr = ((uint8_t *)bsg_reply) + sizeof(struct iscsi_bsg_reply); + memcpy(rsp_ptr, mbox_sts, sizeof(mbox_sts)); + +exit_diag_mem_test: + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: bsg_reply->result = x%x, status = %s\n", + __func__, bsg_reply->result, STATUS(status))); + + bsg_job_done(bsg_job, bsg_reply->result, + bsg_reply->reply_payload_rcv_len); +} + +static int qla4_83xx_wait_for_loopback_config_comp(struct scsi_qla_host *ha, + int wait_for_link) +{ + int status = QLA_SUCCESS; + + if (!wait_for_completion_timeout(&ha->idc_comp, (IDC_COMP_TOV * HZ))) { + ql4_printk(KERN_INFO, ha, "%s: IDC Complete notification not received, Waiting for another %d timeout", + __func__, ha->idc_extend_tmo); + if (ha->idc_extend_tmo) { + if (!wait_for_completion_timeout(&ha->idc_comp, + (ha->idc_extend_tmo * HZ))) { + ha->notify_idc_comp = 0; + ha->notify_link_up_comp = 0; + ql4_printk(KERN_WARNING, ha, "%s: IDC Complete notification not received", + __func__); + status = QLA_ERROR; + goto exit_wait; + } else { + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: IDC Complete notification received\n", + __func__)); + } + } + } else { + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: IDC Complete notification received\n", + __func__)); + } + ha->notify_idc_comp = 0; + + if (wait_for_link) { + if (!wait_for_completion_timeout(&ha->link_up_comp, + (IDC_COMP_TOV * HZ))) { + ha->notify_link_up_comp = 0; + ql4_printk(KERN_WARNING, ha, "%s: LINK UP notification not received", + __func__); + status = QLA_ERROR; + goto exit_wait; + } else { + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: LINK UP notification received\n", + __func__)); + } + ha->notify_link_up_comp = 0; + } + +exit_wait: + return status; +} + +static int qla4_83xx_pre_loopback_config(struct scsi_qla_host *ha, + uint32_t *mbox_cmd) +{ + uint32_t config = 0; + int status = QLA_SUCCESS; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: in\n", __func__)); + + status = qla4_83xx_get_port_config(ha, &config); + if (status != QLA_SUCCESS) + goto exit_pre_loopback_config; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: Default port config=%08X\n", + __func__, config)); + + if ((config & ENABLE_INTERNAL_LOOPBACK) || + (config & ENABLE_EXTERNAL_LOOPBACK)) { + ql4_printk(KERN_INFO, ha, "%s: Loopback diagnostics already in progress. Invalid requiest\n", + __func__); + goto exit_pre_loopback_config; + } + + if (mbox_cmd[1] == QL_DIAG_CMD_TEST_INT_LOOPBACK) + config |= ENABLE_INTERNAL_LOOPBACK; + + if (mbox_cmd[1] == QL_DIAG_CMD_TEST_EXT_LOOPBACK) + config |= ENABLE_EXTERNAL_LOOPBACK; + + config &= ~ENABLE_DCBX; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: New port config=%08X\n", + __func__, config)); + + ha->notify_idc_comp = 1; + ha->notify_link_up_comp = 1; + + /* get the link state */ + qla4xxx_get_firmware_state(ha); + + status = qla4_83xx_set_port_config(ha, &config); + if (status != QLA_SUCCESS) { + ha->notify_idc_comp = 0; + ha->notify_link_up_comp = 0; + goto exit_pre_loopback_config; + } +exit_pre_loopback_config: + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: status = %s\n", __func__, + STATUS(status))); + return status; +} + +static int qla4_83xx_post_loopback_config(struct scsi_qla_host *ha, + uint32_t *mbox_cmd) +{ + int status = QLA_SUCCESS; + uint32_t config = 0; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: in\n", __func__)); + + status = qla4_83xx_get_port_config(ha, &config); + if (status != QLA_SUCCESS) + goto exit_post_loopback_config; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: port config=%08X\n", __func__, + config)); + + if (mbox_cmd[1] == QL_DIAG_CMD_TEST_INT_LOOPBACK) + config &= ~ENABLE_INTERNAL_LOOPBACK; + else if (mbox_cmd[1] == QL_DIAG_CMD_TEST_EXT_LOOPBACK) + config &= ~ENABLE_EXTERNAL_LOOPBACK; + + config |= ENABLE_DCBX; + + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: Restore default port config=%08X\n", __func__, + config)); + + ha->notify_idc_comp = 1; + if (ha->addl_fw_state & FW_ADDSTATE_LINK_UP) + ha->notify_link_up_comp = 1; + + status = qla4_83xx_set_port_config(ha, &config); + if (status != QLA_SUCCESS) { + ql4_printk(KERN_INFO, ha, "%s: Scheduling adapter reset\n", + __func__); + set_bit(DPC_RESET_HA, &ha->dpc_flags); + clear_bit(AF_LOOPBACK, &ha->flags); + goto exit_post_loopback_config; + } + +exit_post_loopback_config: + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: status = %s\n", __func__, + STATUS(status))); + return status; +} + +static void qla4xxx_execute_diag_loopback_cmd(struct bsg_job *bsg_job) +{ + struct Scsi_Host *host = iscsi_job_to_shost(bsg_job); + struct scsi_qla_host *ha = to_qla_host(host); + struct iscsi_bsg_request *bsg_req = bsg_job->request; + struct iscsi_bsg_reply *bsg_reply = bsg_job->reply; + uint8_t *rsp_ptr = NULL; + uint32_t mbox_cmd[MBOX_REG_COUNT]; + uint32_t mbox_sts[MBOX_REG_COUNT]; + int wait_for_link = 1; + int status = QLA_ERROR; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: in\n", __func__)); + + bsg_reply->reply_payload_rcv_len = 0; + + if (test_bit(AF_LOOPBACK, &ha->flags)) { + ql4_printk(KERN_INFO, ha, "%s: Loopback Diagnostics already in progress. Invalid Request\n", + __func__); + bsg_reply->result = DID_ERROR << 16; + goto exit_loopback_cmd; + } + + if (test_bit(DPC_RESET_HA, &ha->dpc_flags)) { + ql4_printk(KERN_INFO, ha, "%s: Adapter reset in progress. Invalid Request\n", + __func__); + bsg_reply->result = DID_ERROR << 16; + goto exit_loopback_cmd; + } + + memcpy(mbox_cmd, &bsg_req->rqst_data.h_vendor.vendor_cmd[1], + sizeof(uint32_t) * MBOX_REG_COUNT); + + if (is_qla8032(ha) || is_qla8042(ha)) { + status = qla4_83xx_pre_loopback_config(ha, mbox_cmd); + if (status != QLA_SUCCESS) { + bsg_reply->result = DID_ERROR << 16; + goto exit_loopback_cmd; + } + + status = qla4_83xx_wait_for_loopback_config_comp(ha, + wait_for_link); + if (status != QLA_SUCCESS) { + bsg_reply->result = DID_TIME_OUT << 16; + goto restore; + } + } + + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: mbox_cmd: %08X %08X %08X %08X %08X %08X %08X %08X\n", + __func__, mbox_cmd[0], mbox_cmd[1], mbox_cmd[2], + mbox_cmd[3], mbox_cmd[4], mbox_cmd[5], mbox_cmd[6], + mbox_cmd[7])); + + status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, 8, &mbox_cmd[0], + &mbox_sts[0]); + + if (status == QLA_SUCCESS) + bsg_reply->result = DID_OK << 16; + else + bsg_reply->result = DID_ERROR << 16; + + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: mbox_sts: %08X %08X %08X %08X %08X %08X %08X %08X\n", + __func__, mbox_sts[0], mbox_sts[1], mbox_sts[2], + mbox_sts[3], mbox_sts[4], mbox_sts[5], mbox_sts[6], + mbox_sts[7])); + + /* Send mbox_sts to application */ + bsg_job->reply_len = sizeof(struct iscsi_bsg_reply) + sizeof(mbox_sts); + rsp_ptr = ((uint8_t *)bsg_reply) + sizeof(struct iscsi_bsg_reply); + memcpy(rsp_ptr, mbox_sts, sizeof(mbox_sts)); +restore: + if (is_qla8032(ha) || is_qla8042(ha)) { + status = qla4_83xx_post_loopback_config(ha, mbox_cmd); + if (status != QLA_SUCCESS) { + bsg_reply->result = DID_ERROR << 16; + goto exit_loopback_cmd; + } + + /* for pre_loopback_config() wait for LINK UP only + * if PHY LINK is UP */ + if (!(ha->addl_fw_state & FW_ADDSTATE_LINK_UP)) + wait_for_link = 0; + + status = qla4_83xx_wait_for_loopback_config_comp(ha, + wait_for_link); + if (status != QLA_SUCCESS) { + bsg_reply->result = DID_TIME_OUT << 16; + goto exit_loopback_cmd; + } + } +exit_loopback_cmd: + DEBUG2(ql4_printk(KERN_INFO, ha, + "%s: bsg_reply->result = x%x, status = %s\n", + __func__, bsg_reply->result, STATUS(status))); + bsg_job_done(bsg_job, bsg_reply->result, + bsg_reply->reply_payload_rcv_len); +} + +static int qla4xxx_execute_diag_test(struct bsg_job *bsg_job) +{ + struct Scsi_Host *host = iscsi_job_to_shost(bsg_job); + struct scsi_qla_host *ha = to_qla_host(host); + struct iscsi_bsg_request *bsg_req = bsg_job->request; + uint32_t diag_cmd; + int rval = -EINVAL; + + DEBUG2(ql4_printk(KERN_INFO, ha, "%s: in\n", __func__)); + + diag_cmd = bsg_req->rqst_data.h_vendor.vendor_cmd[1]; + if (diag_cmd == MBOX_CMD_DIAG_TEST) { + switch (bsg_req->rqst_data.h_vendor.vendor_cmd[2]) { + case QL_DIAG_CMD_TEST_DDR_SIZE: + case QL_DIAG_CMD_TEST_DDR_RW: + case QL_DIAG_CMD_TEST_ONCHIP_MEM_RW: + case QL_DIAG_CMD_TEST_NVRAM: + case QL_DIAG_CMD_TEST_FLASH_ROM: + case QL_DIAG_CMD_TEST_DMA_XFER: + case QL_DIAG_CMD_SELF_DDR_RW: + case QL_DIAG_CMD_SELF_ONCHIP_MEM_RW: + /* Execute diag test for adapter RAM/FLASH */ + ql4xxx_execute_diag_cmd(bsg_job); + /* Always return success as we want to sent bsg_reply + * to Application */ + rval = QLA_SUCCESS; + break; + + case QL_DIAG_CMD_TEST_INT_LOOPBACK: + case QL_DIAG_CMD_TEST_EXT_LOOPBACK: + /* Execute diag test for Network */ + qla4xxx_execute_diag_loopback_cmd(bsg_job); + /* Always return success as we want to sent bsg_reply + * to Application */ + rval = QLA_SUCCESS; + break; + default: + ql4_printk(KERN_ERR, ha, "%s: Invalid diag test: 0x%x\n", + __func__, + bsg_req->rqst_data.h_vendor.vendor_cmd[2]); + } + } else if ((diag_cmd == MBOX_CMD_SET_LED_CONFIG) || + (diag_cmd == MBOX_CMD_GET_LED_CONFIG)) { + ql4xxx_execute_diag_cmd(bsg_job); + rval = QLA_SUCCESS; + } else { + ql4_printk(KERN_ERR, ha, "%s: Invalid diag cmd: 0x%x\n", + __func__, diag_cmd); + } + + return rval; +} + /** * qla4xxx_process_vendor_specific - handle vendor specific bsg request * @job: iscsi_bsg_job to handle @@ -479,6 +836,9 @@ int qla4xxx_process_vendor_specific(struct bsg_job *bsg_job) case QLISCSI_VND_GET_ACB: return qla4xxx_bsg_get_acb(bsg_job); + case QLISCSI_VND_DIAG_TEST: + return qla4xxx_execute_diag_test(bsg_job); + default: ql4_printk(KERN_ERR, ha, "%s: invalid BSG vendor command: " "0x%x\n", __func__, bsg_req->msgcode); diff --git a/drivers/scsi/qla4xxx/ql4_bsg.h b/drivers/scsi/qla4xxx/ql4_bsg.h index c6a0364509f..88c2401910c 100644 --- a/drivers/scsi/qla4xxx/ql4_bsg.h +++ b/drivers/scsi/qla4xxx/ql4_bsg.h @@ -15,5 +15,18 @@ #define QLISCSI_VND_UPDATE_NVRAM 5 #define QLISCSI_VND_RESTORE_DEFAULTS 6 #define QLISCSI_VND_GET_ACB 7 +#define QLISCSI_VND_DIAG_TEST 8 + +/* QLISCSI_VND_DIAG_CMD sub code */ +#define QL_DIAG_CMD_TEST_DDR_SIZE 0x2 +#define QL_DIAG_CMD_TEST_DDR_RW 0x3 +#define QL_DIAG_CMD_TEST_ONCHIP_MEM_RW 0x4 +#define QL_DIAG_CMD_TEST_NVRAM 0x5 /* Only ISP4XXX */ +#define QL_DIAG_CMD_TEST_FLASH_ROM 0x6 +#define QL_DIAG_CMD_TEST_INT_LOOPBACK 0x7 +#define QL_DIAG_CMD_TEST_EXT_LOOPBACK 0x8 +#define QL_DIAG_CMD_TEST_DMA_XFER 0x9 /* Only ISP4XXX */ +#define QL_DIAG_CMD_SELF_DDR_RW 0xC +#define QL_DIAG_CMD_SELF_ONCHIP_MEM_RW 0xD #endif diff --git a/drivers/scsi/qla4xxx/ql4_def.h b/drivers/scsi/qla4xxx/ql4_def.h index 084d1fd59c9..aa67bb9a442 100644 --- a/drivers/scsi/qla4xxx/ql4_def.h +++ b/drivers/scsi/qla4xxx/ql4_def.h @@ -73,6 +73,7 @@ #define QLA_SUCCESS 0 #define QLA_ERROR 1 +#define STATUS(status) status == QLA_ERROR ? "FAILED" : "SUCCEEDED" /* * Data bit definitions @@ -179,6 +180,10 @@ n &= ~v; \ } +#define OP_STATE(o, f, p) { \ + p = (o & f) ? "enable" : "disable"; \ +} + /* * Retry & Timeout Values */ @@ -206,6 +211,8 @@ #define MAX_RESET_HA_RETRIES 2 #define FW_ALIVE_WAIT_TOV 3 #define IDC_EXTEND_TOV 8 +#define IDC_COMP_TOV 5 +#define LINK_UP_COMP_TOV 30 #define CMD_SP(Cmnd) ((Cmnd)->SCp.ptr) @@ -476,6 +483,34 @@ struct ipaddress_config { uint16_t eth_mtu_size; uint16_t ipv4_port; uint16_t ipv6_port; + uint8_t control; + uint16_t ipv6_tcp_options; + uint8_t tcp_wsf; + uint8_t ipv6_tcp_wsf; + uint8_t ipv4_tos; + uint8_t ipv4_cache_id; + uint8_t ipv6_cache_id; + uint8_t ipv4_alt_cid_len; + uint8_t ipv4_alt_cid[11]; + uint8_t ipv4_vid_len; + uint8_t ipv4_vid[11]; + uint8_t ipv4_ttl; + uint16_t ipv6_flow_lbl; + uint8_t ipv6_traffic_class; + uint8_t ipv6_hop_limit; + uint32_t ipv6_nd_reach_time; + uint32_t ipv6_nd_rexmit_timer; + uint32_t ipv6_nd_stale_timeout; + uint8_t ipv6_dup_addr_detect_count; + uint32_t ipv6_gw_advrt_mtu; + uint16_t def_timeout; + uint8_t abort_timer; + uint16_t iscsi_options; + uint16_t iscsi_max_pdu_size; + uint16_t iscsi_first_burst_len; + uint16_t iscsi_max_outstnd_r2t; + uint16_t iscsi_max_burst_len; + uint8_t iscsi_name[224]; }; #define QL4_CHAP_MAX_NAME_LEN 256 @@ -790,6 +825,11 @@ struct scsi_qla_host { uint32_t pf_bit; struct qla4_83xx_idc_information idc_info; struct addr_ctrl_blk *saved_acb; + int notify_idc_comp; + int notify_link_up_comp; + int idc_extend_tmo; + struct completion idc_comp; + struct completion link_up_comp; }; struct ql4_task_data { diff --git a/drivers/scsi/qla4xxx/ql4_fw.h b/drivers/scsi/qla4xxx/ql4_fw.h index 1243e5942b7..8d4092b33c0 100644 --- a/drivers/scsi/qla4xxx/ql4_fw.h +++ b/drivers/scsi/qla4xxx/ql4_fw.h @@ -410,6 +410,7 @@ struct qla_flt_region { #define DDB_DS_LOGIN_IN_PROCESS 0x07 #define MBOX_CMD_GET_FW_STATE 0x0069 #define MBOX_CMD_GET_INIT_FW_CTRL_BLOCK_DEFAULTS 0x006A +#define MBOX_CMD_DIAG_TEST 0x0075 #define MBOX_CMD_GET_SYS_INFO 0x0078 #define MBOX_CMD_GET_NVRAM 0x0078 /* For 40xx */ #define MBOX_CMD_SET_NVRAM 0x0079 /* For 40xx */ @@ -425,8 +426,17 @@ struct qla_flt_region { #define MBOX_CMD_GET_IP_ADDR_STATE 0x0091 #define MBOX_CMD_SEND_IPV6_ROUTER_SOL 0x0092 #define MBOX_CMD_GET_DB_ENTRY_CURRENT_IP_ADDR 0x0093 +#define MBOX_CMD_SET_PORT_CONFIG 0x0122 +#define MBOX_CMD_GET_PORT_CONFIG 0x0123 +#define MBOX_CMD_SET_LED_CONFIG 0x0125 +#define MBOX_CMD_GET_LED_CONFIG 0x0126 #define MBOX_CMD_MINIDUMP 0x0129 +/* Port Config */ +#define ENABLE_INTERNAL_LOOPBACK 0x04 +#define ENABLE_EXTERNAL_LOOPBACK 0x08 +#define ENABLE_DCBX 0x10 + /* Minidump subcommand */ #define MINIDUMP_GET_SIZE_SUBCOMMAND 0x00 #define MINIDUMP_GET_TMPLT_SUBCOMMAND 0x01 @@ -535,10 +545,6 @@ struct qla_flt_region { #define FLASH_OPT_COMMIT 2 #define FLASH_OPT_RMW_COMMIT 3 -/* Loopback type */ -#define ENABLE_INTERNAL_LOOPBACK 0x04 -#define ENABLE_EXTERNAL_LOOPBACK 0x08 - /* generic defines to enable/disable params */ #define QL4_PARAM_DISABLE 0 #define QL4_PARAM_ENABLE 1 @@ -551,6 +557,7 @@ struct addr_ctrl_blk { #define IFCB_VER_MIN 0x01 #define IFCB_VER_MAX 0x02 uint8_t control; /* 01 */ +#define CTRLOPT_NEW_CONN_DISABLE 0x0002 uint16_t fw_options; /* 02-03 */ #define FWOPT_HEARTBEAT_ENABLE 0x1000 @@ -582,11 +589,40 @@ struct addr_ctrl_blk { uint32_t shdwreg_addr_hi; /* 2C-2F */ uint16_t iscsi_opts; /* 30-31 */ +#define ISCSIOPTS_HEADER_DIGEST_EN 0x2000 +#define ISCSIOPTS_DATA_DIGEST_EN 0x1000 +#define ISCSIOPTS_IMMEDIATE_DATA_EN 0x0800 +#define ISCSIOPTS_INITIAL_R2T_EN 0x0400 +#define ISCSIOPTS_DATA_SEQ_INORDER_EN 0x0200 +#define ISCSIOPTS_DATA_PDU_INORDER_EN 0x0100 +#define ISCSIOPTS_CHAP_AUTH_EN 0x0080 +#define ISCSIOPTS_SNACK_EN 0x0040 +#define ISCSIOPTS_DISCOVERY_LOGOUT_EN 0x0020 +#define ISCSIOPTS_BIDI_CHAP_EN 0x0010 +#define ISCSIOPTS_DISCOVERY_AUTH_EN 0x0008 +#define ISCSIOPTS_STRICT_LOGIN_COMP_EN 0x0004 +#define ISCSIOPTS_ERL 0x0003 uint16_t ipv4_tcp_opts; /* 32-33 */ +#define TCPOPT_DELAYED_ACK_DISABLE 0x8000 #define TCPOPT_DHCP_ENABLE 0x0200 +#define TCPOPT_DNS_SERVER_IP_EN 0x0100 +#define TCPOPT_SLP_DA_INFO_EN 0x0080 +#define TCPOPT_NAGLE_ALGO_DISABLE 0x0020 +#define TCPOPT_WINDOW_SCALE_DISABLE 0x0010 +#define TCPOPT_TIMER_SCALE 0x000E +#define TCPOPT_TIMESTAMP_ENABLE 0x0001 uint16_t ipv4_ip_opts; /* 34-35 */ #define IPOPT_IPV4_PROTOCOL_ENABLE 0x8000 +#define IPOPT_IPV4_TOS_EN 0x4000 #define IPOPT_VLAN_TAGGING_ENABLE 0x2000 +#define IPOPT_GRAT_ARP_EN 0x1000 +#define IPOPT_ALT_CID_EN 0x0800 +#define IPOPT_REQ_VID_EN 0x0400 +#define IPOPT_USE_VID_EN 0x0200 +#define IPOPT_LEARN_IQN_EN 0x0100 +#define IPOPT_FRAGMENTATION_DISABLE 0x0010 +#define IPOPT_IN_FORWARD_EN 0x0008 +#define IPOPT_ARP_REDIRECT_EN 0x0004 uint16_t iscsi_max_pdu_size; /* 36-37 */ uint8_t ipv4_tos; /* 38 */ @@ -637,15 +673,24 @@ struct addr_ctrl_blk { uint32_t cookie; /* 200-203 */ uint16_t ipv6_port; /* 204-205 */ uint16_t ipv6_opts; /* 206-207 */ -#define IPV6_OPT_IPV6_PROTOCOL_ENABLE 0x8000 -#define IPV6_OPT_VLAN_TAGGING_ENABLE 0x2000 +#define IPV6_OPT_IPV6_PROTOCOL_ENABLE 0x8000 +#define IPV6_OPT_VLAN_TAGGING_ENABLE 0x2000 +#define IPV6_OPT_GRAT_NEIGHBOR_ADV_EN 0x1000 +#define IPV6_OPT_REDIRECT_EN 0x0004 uint16_t ipv6_addtl_opts; /* 208-209 */ +#define IPV6_ADDOPT_IGNORE_ICMP_ECHO_REQ 0x0040 +#define IPV6_ADDOPT_MLD_EN 0x0004 #define IPV6_ADDOPT_NEIGHBOR_DISCOVERY_ADDR_ENABLE 0x0002 /* Pri ACB Only */ #define IPV6_ADDOPT_AUTOCONFIG_LINK_LOCAL_ADDR 0x0001 uint16_t ipv6_tcp_opts; /* 20A-20B */ +#define IPV6_TCPOPT_DELAYED_ACK_DISABLE 0x8000 +#define IPV6_TCPOPT_NAGLE_ALGO_DISABLE 0x0020 +#define IPV6_TCPOPT_WINDOW_SCALE_DISABLE 0x0010 +#define IPV6_TCPOPT_TIMER_SCALE 0x000E +#define IPV6_TCPOPT_TIMESTAMP_EN 0x0001 uint8_t ipv6_tcp_wsf; /* 20C */ uint16_t ipv6_flow_lbl; /* 20D-20F */ uint8_t ipv6_dflt_rtr_addr[16]; /* 210-21F */ @@ -1252,7 +1297,88 @@ struct response { }; struct ql_iscsi_stats { - uint8_t reserved1[656]; /* 0000-028F */ + uint64_t mac_tx_frames; /* 0000–0007 */ + uint64_t mac_tx_bytes; /* 0008–000F */ + uint64_t mac_tx_multicast_frames; /* 0010–0017 */ + uint64_t mac_tx_broadcast_frames; /* 0018–001F */ + uint64_t mac_tx_pause_frames; /* 0020–0027 */ + uint64_t mac_tx_control_frames; /* 0028–002F */ + uint64_t mac_tx_deferral; /* 0030–0037 */ + uint64_t mac_tx_excess_deferral; /* 0038–003F */ + uint64_t mac_tx_late_collision; /* 0040–0047 */ + uint64_t mac_tx_abort; /* 0048–004F */ + uint64_t mac_tx_single_collision; /* 0050–0057 */ + uint64_t mac_tx_multiple_collision; /* 0058–005F */ + uint64_t mac_tx_collision; /* 0060–0067 */ + uint64_t mac_tx_frames_dropped; /* 0068–006F */ + uint64_t mac_tx_jumbo_frames; /* 0070–0077 */ + uint64_t mac_rx_frames; /* 0078–007F */ + uint64_t mac_rx_bytes; /* 0080–0087 */ + uint64_t mac_rx_unknown_control_frames; /* 0088–008F */ + uint64_t mac_rx_pause_frames; /* 0090–0097 */ + uint64_t mac_rx_control_frames; /* 0098–009F */ + uint64_t mac_rx_dribble; /* 00A0–00A7 */ + uint64_t mac_rx_frame_length_error; /* 00A8–00AF */ + uint64_t mac_rx_jabber; /* 00B0–00B7 */ + uint64_t mac_rx_carrier_sense_error; /* 00B8–00BF */ + uint64_t mac_rx_frame_discarded; /* 00C0–00C7 */ + uint64_t mac_rx_frames_dropped; /* 00C8–00CF */ + uint64_t mac_crc_error; /* 00D0–00D7 */ + uint64_t mac_encoding_error; /* 00D8–00DF */ + uint64_t mac_rx_length_error_large; /* 00E0–00E7 */ + uint64_t mac_rx_length_error_small; /* 00E8–00EF */ + uint64_t mac_rx_multicast_frames; /* 00F0–00F7 */ + uint64_t mac_rx_broadcast_frames; /* 00F8–00FF */ + uint64_t ip_tx_packets; /* 0100–0107 */ + uint64_t ip_tx_bytes; /* 0108–010F */ + uint64_t ip_tx_fragments; /* 0110–0117 */ + uint64_t ip_rx_packets; /* 0118–011F */ + uint64_t ip_rx_bytes; /* 0120–0127 */ + uint64_t ip_rx_fragments; /* 0128–012F */ + uint64_t ip_datagram_reassembly; /* 0130–0137 */ + uint64_t ip_invalid_address_error; /* 0138–013F */ + uint64_t ip_error_packets; /* 0140–0147 */ + uint64_t ip_fragrx_overlap; /* 0148–014F */ + uint64_t ip_fragrx_outoforder; /* 0150–0157 */ + uint64_t ip_datagram_reassembly_timeout; /* 0158–015F */ + uint64_t ipv6_tx_packets; /* 0160–0167 */ + uint64_t ipv6_tx_bytes; /* 0168–016F */ + uint64_t ipv6_tx_fragments; /* 0170–0177 */ + uint64_t ipv6_rx_packets; /* 0178–017F */ + uint64_t ipv6_rx_bytes; /* 0180–0187 */ + uint64_t ipv6_rx_fragments; /* 0188–018F */ + uint64_t ipv6_datagram_reassembly; /* 0190–0197 */ + uint64_t ipv6_invalid_address_error; /* 0198–019F */ + uint64_t ipv6_error_packets; /* 01A0–01A7 */ + uint64_t ipv6_fragrx_overlap; /* 01A8–01AF */ + uint64_t ipv6_fragrx_outoforder; /* 01B0–01B7 */ + uint64_t ipv6_datagram_reassembly_timeout; /* 01B8–01BF */ + uint64_t tcp_tx_segments; /* 01C0–01C7 */ + uint64_t tcp_tx_bytes; /* 01C8–01CF */ + uint64_t tcp_rx_segments; /* 01D0–01D7 */ + uint64_t tcp_rx_byte; /* 01D8–01DF */ + uint64_t tcp_duplicate_ack_retx; /* 01E0–01E7 */ + uint64_t tcp_retx_timer_expired; /* 01E8–01EF */ + uint64_t tcp_rx_duplicate_ack; /* 01F0–01F7 */ + uint64_t tcp_rx_pure_ackr; /* 01F8–01FF */ + uint64_t tcp_tx_delayed_ack; /* 0200–0207 */ + uint64_t tcp_tx_pure_ack; /* 0208–020F */ + uint64_t tcp_rx_segment_error; /* 0210–0217 */ + uint64_t tcp_rx_segment_outoforder; /* 0218–021F */ + uint64_t tcp_rx_window_probe; /* 0220–0227 */ + uint64_t tcp_rx_window_update; /* 0228–022F */ + uint64_t tcp_tx_window_probe_persist; /* 0230–0237 */ + uint64_t ecc_error_correction; /* 0238–023F */ + uint64_t iscsi_pdu_tx; /* 0240-0247 */ + uint64_t iscsi_data_bytes_tx; /* 0248-024F */ + uint64_t iscsi_pdu_rx; /* 0250-0257 */ + uint64_t iscsi_data_bytes_rx; /* 0258-025F */ + uint64_t iscsi_io_completed; /* 0260-0267 */ + uint64_t iscsi_unexpected_io_rx; /* 0268-026F */ + uint64_t iscsi_format_error; /* 0270-0277 */ + uint64_t iscsi_hdr_digest_error; /* 0278-027F */ + uint64_t iscsi_data_digest_error; /* 0280-0287 */ + uint64_t iscsi_sequence_error; /* 0288-028F */ uint32_t tx_cmd_pdu; /* 0290-0293 */ uint32_t tx_resp_pdu; /* 0294-0297 */ uint32_t rx_cmd_pdu; /* 0298-029B */ diff --git a/drivers/scsi/qla4xxx/ql4_glbl.h b/drivers/scsi/qla4xxx/ql4_glbl.h index 5cef2527180..d67c50e0b89 100644 --- a/drivers/scsi/qla4xxx/ql4_glbl.h +++ b/drivers/scsi/qla4xxx/ql4_glbl.h @@ -276,6 +276,9 @@ int qla4xxx_get_acb(struct scsi_qla_host *ha, dma_addr_t acb_dma, int qla4_84xx_config_acb(struct scsi_qla_host *ha, int acb_config); int qla4_83xx_ms_mem_write_128b(struct scsi_qla_host *ha, uint64_t addr, uint32_t *data, uint32_t count); +uint8_t qla4xxx_set_ipaddr_state(uint8_t fw_ipaddr_state); +int qla4_83xx_get_port_config(struct scsi_qla_host *ha, uint32_t *config); +int qla4_83xx_set_port_config(struct scsi_qla_host *ha, uint32_t *config); extern int ql4xextended_error_logging; extern int ql4xdontresethba; diff --git a/drivers/scsi/qla4xxx/ql4_isr.c b/drivers/scsi/qla4xxx/ql4_isr.c index 7dff09f09b7..a3c8bc7706c 100644 --- a/drivers/scsi/qla4xxx/ql4_isr.c +++ b/drivers/scsi/qla4xxx/ql4_isr.c @@ -606,6 +606,36 @@ static int qla4_83xx_loopback_in_progress(struct scsi_qla_host *ha) return rval; } +static void qla4xxx_update_ipaddr_state(struct scsi_qla_host *ha, + uint32_t ipaddr_idx, + uint32_t ipaddr_fw_state) +{ + uint8_t ipaddr_state; + uint8_t ip_idx; + + ip_idx = ipaddr_idx & 0xF; + ipaddr_state = qla4xxx_set_ipaddr_state((uint8_t)ipaddr_fw_state); + + switch (ip_idx) { + case 0: + ha->ip_config.ipv4_addr_state = ipaddr_state; + break; + case 1: + ha->ip_config.ipv6_link_local_state = ipaddr_state; + break; + case 2: + ha->ip_config.ipv6_addr0_state = ipaddr_state; + break; + case 3: + ha->ip_config.ipv6_addr1_state = ipaddr_state; + break; + default: + ql4_printk(KERN_INFO, ha, "%s: Invalid IPADDR index %d\n", + __func__, ip_idx); + } +} + + /** * qla4xxx_isr_decode_mailbox - decodes mailbox status * @ha: Pointer to host adapter structure. @@ -620,6 +650,7 @@ static void qla4xxx_isr_decode_mailbox(struct scsi_qla_host * ha, int i; uint32_t mbox_sts[MBOX_AEN_REG_COUNT]; __le32 __iomem *mailbox_out; + uint32_t opcode = 0; if (is_qla8032(ha) || is_qla8042(ha)) mailbox_out = &ha->qla4_83xx_reg->mailbox_out[0]; @@ -698,6 +729,11 @@ static void qla4xxx_isr_decode_mailbox(struct scsi_qla_host * ha, qla4xxx_post_aen_work(ha, ISCSI_EVENT_LINKUP, sizeof(mbox_sts), (uint8_t *) mbox_sts); + + if ((is_qla8032(ha) || is_qla8042(ha)) && + ha->notify_link_up_comp) + complete(&ha->link_up_comp); + break; case MBOX_ASTS_LINK_DOWN: @@ -741,6 +777,8 @@ static void qla4xxx_isr_decode_mailbox(struct scsi_qla_host * ha, "mbox_sts[3]=%04x\n", ha->host_no, mbox_sts[0], mbox_sts[2], mbox_sts[3]); + qla4xxx_update_ipaddr_state(ha, mbox_sts[5], + mbox_sts[3]); /* mbox_sts[2] = Old ACB state * mbox_sts[3] = new ACB state */ if ((mbox_sts[3] == ACB_STATE_VALID) && @@ -841,8 +879,6 @@ static void qla4xxx_isr_decode_mailbox(struct scsi_qla_host * ha, break; case MBOX_ASTS_IDC_REQUEST_NOTIFICATION: - { - uint32_t opcode; if (is_qla8032(ha) || is_qla8042(ha)) { DEBUG2(ql4_printk(KERN_INFO, ha, "scsi%ld: AEN %04x, mbox_sts[1]=%08x, mbox_sts[2]=%08x, mbox_sts[3]=%08x, mbox_sts[4]=%08x\n", @@ -862,7 +898,6 @@ static void qla4xxx_isr_decode_mailbox(struct scsi_qla_host * ha, } } break; - } case MBOX_ASTS_IDC_COMPLETE: if (is_qla8032(ha) || is_qla8042(ha)) { @@ -875,6 +910,14 @@ static void qla4xxx_isr_decode_mailbox(struct scsi_qla_host * ha, "scsi:%ld: AEN %04x IDC Complete notification\n", ha->host_no, mbox_sts[0])); + opcode = mbox_sts[1] >> 16; + if (ha->notify_idc_comp) + complete(&ha->idc_comp); + + if ((opcode == MBOX_CMD_SET_PORT_CONFIG) || + (opcode == MBOX_CMD_PORT_RESET)) + ha->idc_info.info2 = mbox_sts[3]; + if (qla4_83xx_loopback_in_progress(ha)) { set_bit(AF_LOOPBACK, &ha->flags); } else { @@ -907,6 +950,8 @@ static void qla4xxx_isr_decode_mailbox(struct scsi_qla_host * ha, DEBUG2(ql4_printk(KERN_INFO, ha, "scsi%ld: AEN %04x Received IDC Extend Timeout notification\n", ha->host_no, mbox_sts[0])); + /* new IDC timeout */ + ha->idc_extend_tmo = mbox_sts[1]; break; case MBOX_ASTS_INITIALIZATION_FAILED: diff --git a/drivers/scsi/qla4xxx/ql4_mbx.c b/drivers/scsi/qla4xxx/ql4_mbx.c index 22cbd005bdf..9ae8ca3b69f 100644 --- a/drivers/scsi/qla4xxx/ql4_mbx.c +++ b/drivers/scsi/qla4xxx/ql4_mbx.c @@ -418,6 +418,38 @@ qla4xxx_get_ifcb(struct scsi_qla_host *ha, uint32_t *mbox_cmd, return QLA_SUCCESS; } +uint8_t qla4xxx_set_ipaddr_state(uint8_t fw_ipaddr_state) +{ + uint8_t ipaddr_state; + + switch (fw_ipaddr_state) { + case IP_ADDRSTATE_UNCONFIGURED: + ipaddr_state = ISCSI_IPDDRESS_STATE_UNCONFIGURED; + break; + case IP_ADDRSTATE_INVALID: + ipaddr_state = ISCSI_IPDDRESS_STATE_INVALID; + break; + case IP_ADDRSTATE_ACQUIRING: + ipaddr_state = ISCSI_IPDDRESS_STATE_ACQUIRING; + break; + case IP_ADDRSTATE_TENTATIVE: + ipaddr_state = ISCSI_IPDDRESS_STATE_TENTATIVE; + break; + case IP_ADDRSTATE_DEPRICATED: + ipaddr_state = ISCSI_IPDDRESS_STATE_DEPRECATED; + break; + case IP_ADDRSTATE_PREFERRED: + ipaddr_state = ISCSI_IPDDRESS_STATE_VALID; + break; + case IP_ADDRSTATE_DISABLING: + ipaddr_state = ISCSI_IPDDRESS_STATE_DISABLING; + break; + default: + ipaddr_state = ISCSI_IPDDRESS_STATE_UNCONFIGURED; + } + return ipaddr_state; +} + static void qla4xxx_update_local_ip(struct scsi_qla_host *ha, struct addr_ctrl_blk *init_fw_cb) @@ -425,7 +457,7 @@ qla4xxx_update_local_ip(struct scsi_qla_host *ha, ha->ip_config.tcp_options = le16_to_cpu(init_fw_cb->ipv4_tcp_opts); ha->ip_config.ipv4_options = le16_to_cpu(init_fw_cb->ipv4_ip_opts); ha->ip_config.ipv4_addr_state = - le16_to_cpu(init_fw_cb->ipv4_addr_state); + qla4xxx_set_ipaddr_state(init_fw_cb->ipv4_addr_state); ha->ip_config.eth_mtu_size = le16_to_cpu(init_fw_cb->eth_mtu_size); ha->ip_config.ipv4_port = le16_to_cpu(init_fw_cb->ipv4_port); @@ -434,6 +466,8 @@ qla4xxx_update_local_ip(struct scsi_qla_host *ha, ha->ip_config.ipv6_options = le16_to_cpu(init_fw_cb->ipv6_opts); ha->ip_config.ipv6_addl_options = le16_to_cpu(init_fw_cb->ipv6_addtl_opts); + ha->ip_config.ipv6_tcp_options = + le16_to_cpu(init_fw_cb->ipv6_tcp_opts); } /* Save IPv4 Address Info */ @@ -448,17 +482,65 @@ qla4xxx_update_local_ip(struct scsi_qla_host *ha, sizeof(init_fw_cb->ipv4_gw_addr))); ha->ip_config.ipv4_vlan_tag = be16_to_cpu(init_fw_cb->ipv4_vlan_tag); + ha->ip_config.control = init_fw_cb->control; + ha->ip_config.tcp_wsf = init_fw_cb->ipv4_tcp_wsf; + ha->ip_config.ipv4_tos = init_fw_cb->ipv4_tos; + ha->ip_config.ipv4_cache_id = init_fw_cb->ipv4_cacheid; + ha->ip_config.ipv4_alt_cid_len = init_fw_cb->ipv4_dhcp_alt_cid_len; + memcpy(ha->ip_config.ipv4_alt_cid, init_fw_cb->ipv4_dhcp_alt_cid, + min(sizeof(ha->ip_config.ipv4_alt_cid), + sizeof(init_fw_cb->ipv4_dhcp_alt_cid))); + ha->ip_config.ipv4_vid_len = init_fw_cb->ipv4_dhcp_vid_len; + memcpy(ha->ip_config.ipv4_vid, init_fw_cb->ipv4_dhcp_vid, + min(sizeof(ha->ip_config.ipv4_vid), + sizeof(init_fw_cb->ipv4_dhcp_vid))); + ha->ip_config.ipv4_ttl = init_fw_cb->ipv4_ttl; + ha->ip_config.def_timeout = le16_to_cpu(init_fw_cb->def_timeout); + ha->ip_config.abort_timer = init_fw_cb->abort_timer; + ha->ip_config.iscsi_options = le16_to_cpu(init_fw_cb->iscsi_opts); + ha->ip_config.iscsi_max_pdu_size = + le16_to_cpu(init_fw_cb->iscsi_max_pdu_size); + ha->ip_config.iscsi_first_burst_len = + le16_to_cpu(init_fw_cb->iscsi_fburst_len); + ha->ip_config.iscsi_max_outstnd_r2t = + le16_to_cpu(init_fw_cb->iscsi_max_outstnd_r2t); + ha->ip_config.iscsi_max_burst_len = + le16_to_cpu(init_fw_cb->iscsi_max_burst_len); + memcpy(ha->ip_config.iscsi_name, init_fw_cb->iscsi_name, + min(sizeof(ha->ip_config.iscsi_name), + sizeof(init_fw_cb->iscsi_name))); if (is_ipv6_enabled(ha)) { /* Save IPv6 Address */ ha->ip_config.ipv6_link_local_state = - le16_to_cpu(init_fw_cb->ipv6_lnk_lcl_addr_state); + qla4xxx_set_ipaddr_state(init_fw_cb->ipv6_lnk_lcl_addr_state); ha->ip_config.ipv6_addr0_state = - le16_to_cpu(init_fw_cb->ipv6_addr0_state); + qla4xxx_set_ipaddr_state(init_fw_cb->ipv6_addr0_state); ha->ip_config.ipv6_addr1_state = - le16_to_cpu(init_fw_cb->ipv6_addr1_state); - ha->ip_config.ipv6_default_router_state = - le16_to_cpu(init_fw_cb->ipv6_dflt_rtr_state); + qla4xxx_set_ipaddr_state(init_fw_cb->ipv6_addr1_state); + + switch (le16_to_cpu(init_fw_cb->ipv6_dflt_rtr_state)) { + case IPV6_RTRSTATE_UNKNOWN: + ha->ip_config.ipv6_default_router_state = + ISCSI_ROUTER_STATE_UNKNOWN; + break; + case IPV6_RTRSTATE_MANUAL: + ha->ip_config.ipv6_default_router_state = + ISCSI_ROUTER_STATE_MANUAL; + break; + case IPV6_RTRSTATE_ADVERTISED: + ha->ip_config.ipv6_default_router_state = + ISCSI_ROUTER_STATE_ADVERTISED; + break; + case IPV6_RTRSTATE_STALE: + ha->ip_config.ipv6_default_router_state = + ISCSI_ROUTER_STATE_STALE; + break; + default: + ha->ip_config.ipv6_default_router_state = + ISCSI_ROUTER_STATE_UNKNOWN; + } + ha->ip_config.ipv6_link_local_addr.in6_u.u6_addr8[0] = 0xFE; ha->ip_config.ipv6_link_local_addr.in6_u.u6_addr8[1] = 0x80; @@ -479,6 +561,23 @@ qla4xxx_update_local_ip(struct scsi_qla_host *ha, ha->ip_config.ipv6_vlan_tag = be16_to_cpu(init_fw_cb->ipv6_vlan_tag); ha->ip_config.ipv6_port = le16_to_cpu(init_fw_cb->ipv6_port); + ha->ip_config.ipv6_cache_id = init_fw_cb->ipv6_cache_id; + ha->ip_config.ipv6_flow_lbl = + le16_to_cpu(init_fw_cb->ipv6_flow_lbl); + ha->ip_config.ipv6_traffic_class = + init_fw_cb->ipv6_traffic_class; + ha->ip_config.ipv6_hop_limit = init_fw_cb->ipv6_hop_limit; + ha->ip_config.ipv6_nd_reach_time = + le32_to_cpu(init_fw_cb->ipv6_nd_reach_time); + ha->ip_config.ipv6_nd_rexmit_timer = + le32_to_cpu(init_fw_cb->ipv6_nd_rexmit_timer); + ha->ip_config.ipv6_nd_stale_timeout = + le32_to_cpu(init_fw_cb->ipv6_nd_stale_timeout); + ha->ip_config.ipv6_dup_addr_detect_count = + init_fw_cb->ipv6_dup_addr_detect_count; + ha->ip_config.ipv6_gw_advrt_mtu = + le32_to_cpu(init_fw_cb->ipv6_gw_advrt_mtu); + ha->ip_config.ipv6_tcp_wsf = init_fw_cb->ipv6_tcp_wsf; } } @@ -2317,3 +2416,46 @@ exit_config_acb: rval == QLA_SUCCESS ? "SUCCEEDED" : "FAILED")); return rval; } + +int qla4_83xx_get_port_config(struct scsi_qla_host *ha, uint32_t *config) +{ + uint32_t mbox_cmd[MBOX_REG_COUNT]; + uint32_t mbox_sts[MBOX_REG_COUNT]; + int status; + + memset(&mbox_cmd, 0, sizeof(mbox_cmd)); + memset(&mbox_sts, 0, sizeof(mbox_sts)); + + mbox_cmd[0] = MBOX_CMD_GET_PORT_CONFIG; + + status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, MBOX_REG_COUNT, + mbox_cmd, mbox_sts); + if (status == QLA_SUCCESS) + *config = mbox_sts[1]; + else + ql4_printk(KERN_ERR, ha, "%s: failed status %04X\n", __func__, + mbox_sts[0]); + + return status; +} + +int qla4_83xx_set_port_config(struct scsi_qla_host *ha, uint32_t *config) +{ + uint32_t mbox_cmd[MBOX_REG_COUNT]; + uint32_t mbox_sts[MBOX_REG_COUNT]; + int status; + + memset(&mbox_cmd, 0, sizeof(mbox_cmd)); + memset(&mbox_sts, 0, sizeof(mbox_sts)); + + mbox_cmd[0] = MBOX_CMD_SET_PORT_CONFIG; + mbox_cmd[1] = *config; + + status = qla4xxx_mailbox_command(ha, MBOX_REG_COUNT, MBOX_REG_COUNT, + mbox_cmd, mbox_sts); + if (status != QLA_SUCCESS) + ql4_printk(KERN_ERR, ha, "%s: failed status %04X\n", __func__, + mbox_sts[0]); + + return status; +} diff --git a/drivers/scsi/qla4xxx/ql4_os.c b/drivers/scsi/qla4xxx/ql4_os.c index a28d5e624aa..c21adc338cf 100644 --- a/drivers/scsi/qla4xxx/ql4_os.c +++ b/drivers/scsi/qla4xxx/ql4_os.c @@ -151,6 +151,7 @@ static int qla4xxx_get_chap_list(struct Scsi_Host *shost, uint16_t chap_tbl_idx, static int qla4xxx_delete_chap(struct Scsi_Host *shost, uint16_t chap_tbl_idx); static int qla4xxx_set_chap_entry(struct Scsi_Host *shost, void *data, int len); +static int qla4xxx_get_host_stats(struct Scsi_Host *shost, char *buf, int len); /* * SCSI host template entry points @@ -262,6 +263,7 @@ static struct iscsi_transport qla4xxx_iscsi_transport = { .login_flashnode = qla4xxx_sysfs_ddb_login, .logout_flashnode = qla4xxx_sysfs_ddb_logout, .logout_flashnode_sid = qla4xxx_sysfs_ddb_logout_sid, + .get_host_stats = qla4xxx_get_host_stats, }; static struct scsi_transport_template *qla4xxx_scsi_transport; @@ -419,6 +421,7 @@ static umode_t qla4_attr_is_visible(int param_type, int param) case ISCSI_PARAM_EXP_STATSN: case ISCSI_PARAM_DISCOVERY_PARENT_IDX: case ISCSI_PARAM_DISCOVERY_PARENT_TYPE: + case ISCSI_PARAM_LOCAL_IPADDR: return S_IRUGO; default: return 0; @@ -440,6 +443,65 @@ static umode_t qla4_attr_is_visible(int param_type, int param) case ISCSI_NET_PARAM_VLAN_ENABLED: case ISCSI_NET_PARAM_MTU: case ISCSI_NET_PARAM_PORT: + case ISCSI_NET_PARAM_IPADDR_STATE: + case ISCSI_NET_PARAM_IPV6_LINKLOCAL_STATE: + case ISCSI_NET_PARAM_IPV6_ROUTER_STATE: + case ISCSI_NET_PARAM_DELAYED_ACK_EN: + case ISCSI_NET_PARAM_TCP_NAGLE_DISABLE: + case ISCSI_NET_PARAM_TCP_WSF_DISABLE: + case ISCSI_NET_PARAM_TCP_WSF: + case ISCSI_NET_PARAM_TCP_TIMER_SCALE: + case ISCSI_NET_PARAM_TCP_TIMESTAMP_EN: + case ISCSI_NET_PARAM_CACHE_ID: + case ISCSI_NET_PARAM_IPV4_DHCP_DNS_ADDR_EN: + case ISCSI_NET_PARAM_IPV4_DHCP_SLP_DA_EN: + case ISCSI_NET_PARAM_IPV4_TOS_EN: + case ISCSI_NET_PARAM_IPV4_TOS: + case ISCSI_NET_PARAM_IPV4_GRAT_ARP_EN: + case ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID_EN: + case ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID: + case ISCSI_NET_PARAM_IPV4_DHCP_REQ_VENDOR_ID_EN: + case ISCSI_NET_PARAM_IPV4_DHCP_USE_VENDOR_ID_EN: + case ISCSI_NET_PARAM_IPV4_DHCP_VENDOR_ID: + case ISCSI_NET_PARAM_IPV4_DHCP_LEARN_IQN_EN: + case ISCSI_NET_PARAM_IPV4_FRAGMENT_DISABLE: + case ISCSI_NET_PARAM_IPV4_IN_FORWARD_EN: + case ISCSI_NET_PARAM_REDIRECT_EN: + case ISCSI_NET_PARAM_IPV4_TTL: + case ISCSI_NET_PARAM_IPV6_GRAT_NEIGHBOR_ADV_EN: + case ISCSI_NET_PARAM_IPV6_MLD_EN: + case ISCSI_NET_PARAM_IPV6_FLOW_LABEL: + case ISCSI_NET_PARAM_IPV6_TRAFFIC_CLASS: + case ISCSI_NET_PARAM_IPV6_HOP_LIMIT: + case ISCSI_NET_PARAM_IPV6_ND_REACHABLE_TMO: + case ISCSI_NET_PARAM_IPV6_ND_REXMIT_TIME: + case ISCSI_NET_PARAM_IPV6_ND_STALE_TMO: + case ISCSI_NET_PARAM_IPV6_DUP_ADDR_DETECT_CNT: + case ISCSI_NET_PARAM_IPV6_RTR_ADV_LINK_MTU: + return S_IRUGO; + default: + return 0; + } + case ISCSI_IFACE_PARAM: + switch (param) { + case ISCSI_IFACE_PARAM_DEF_TASKMGMT_TMO: + case ISCSI_IFACE_PARAM_HDRDGST_EN: + case ISCSI_IFACE_PARAM_DATADGST_EN: + case ISCSI_IFACE_PARAM_IMM_DATA_EN: + case ISCSI_IFACE_PARAM_INITIAL_R2T_EN: + case ISCSI_IFACE_PARAM_DATASEQ_INORDER_EN: + case ISCSI_IFACE_PARAM_PDU_INORDER_EN: + case ISCSI_IFACE_PARAM_ERL: + case ISCSI_IFACE_PARAM_MAX_RECV_DLENGTH: + case ISCSI_IFACE_PARAM_FIRST_BURST: + case ISCSI_IFACE_PARAM_MAX_R2T: + case ISCSI_IFACE_PARAM_MAX_BURST: + case ISCSI_IFACE_PARAM_CHAP_AUTH_EN: + case ISCSI_IFACE_PARAM_BIDI_CHAP_EN: + case ISCSI_IFACE_PARAM_DISCOVERY_AUTH_OPTIONAL: + case ISCSI_IFACE_PARAM_DISCOVERY_LOGOUT_EN: + case ISCSI_IFACE_PARAM_STRICT_LOGIN_COMP_EN: + case ISCSI_IFACE_PARAM_INITIATOR_NAME: return S_IRUGO; default: return 0; @@ -511,6 +573,65 @@ static umode_t qla4_attr_is_visible(int param_type, int param) return 0; } +/** + * qla4xxx_create chap_list - Create CHAP list from FLASH + * @ha: pointer to adapter structure + * + * Read flash and make a list of CHAP entries, during login when a CHAP entry + * is received, it will be checked in this list. If entry exist then the CHAP + * entry index is set in the DDB. If CHAP entry does not exist in this list + * then a new entry is added in FLASH in CHAP table and the index obtained is + * used in the DDB. + **/ +static void qla4xxx_create_chap_list(struct scsi_qla_host *ha) +{ + int rval = 0; + uint8_t *chap_flash_data = NULL; + uint32_t offset; + dma_addr_t chap_dma; + uint32_t chap_size = 0; + + if (is_qla40XX(ha)) + chap_size = MAX_CHAP_ENTRIES_40XX * + sizeof(struct ql4_chap_table); + else /* Single region contains CHAP info for both + * ports which is divided into half for each port. + */ + chap_size = ha->hw.flt_chap_size / 2; + + chap_flash_data = dma_alloc_coherent(&ha->pdev->dev, chap_size, + &chap_dma, GFP_KERNEL); + if (!chap_flash_data) { + ql4_printk(KERN_ERR, ha, "No memory for chap_flash_data\n"); + return; + } + + if (is_qla40XX(ha)) { + offset = FLASH_CHAP_OFFSET; + } else { + offset = FLASH_RAW_ACCESS_ADDR + (ha->hw.flt_region_chap << 2); + if (ha->port_num == 1) + offset += chap_size; + } + + rval = qla4xxx_get_flash(ha, chap_dma, offset, chap_size); + if (rval != QLA_SUCCESS) + goto exit_chap_list; + + if (ha->chap_list == NULL) + ha->chap_list = vmalloc(chap_size); + if (ha->chap_list == NULL) { + ql4_printk(KERN_ERR, ha, "No memory for ha->chap_list\n"); + goto exit_chap_list; + } + + memset(ha->chap_list, 0, chap_size); + memcpy(ha->chap_list, chap_flash_data, chap_size); + +exit_chap_list: + dma_free_coherent(&ha->pdev->dev, chap_size, chap_flash_data, chap_dma); +} + static int qla4xxx_get_chap_by_index(struct scsi_qla_host *ha, int16_t chap_index, struct ql4_chap_table **chap_entry) @@ -624,6 +745,8 @@ static int qla4xxx_get_chap_list(struct Scsi_Host *shost, uint16_t chap_tbl_idx, goto exit_get_chap_list; } + qla4xxx_create_chap_list(ha); + chap_rec = (struct iscsi_chap_rec *) buf; mutex_lock(&ha->chap_sem); for (i = chap_tbl_idx; i < max_chap_entries; i++) { @@ -802,6 +925,7 @@ static int qla4xxx_set_chap_entry(struct Scsi_Host *shost, void *data, int len) int type; int rem = len; int rc = 0; + int size; memset(&chap_rec, 0, sizeof(chap_rec)); @@ -816,12 +940,14 @@ static int qla4xxx_set_chap_entry(struct Scsi_Host *shost, void *data, int len) chap_rec.chap_type = param_info->value[0]; break; case ISCSI_CHAP_PARAM_USERNAME: - memcpy(chap_rec.username, param_info->value, - param_info->len); + size = min_t(size_t, sizeof(chap_rec.username), + param_info->len); + memcpy(chap_rec.username, param_info->value, size); break; case ISCSI_CHAP_PARAM_PASSWORD: - memcpy(chap_rec.password, param_info->value, - param_info->len); + size = min_t(size_t, sizeof(chap_rec.password), + param_info->len); + memcpy(chap_rec.password, param_info->value, size); break; case ISCSI_CHAP_PARAM_PASSWORD_LEN: chap_rec.password_length = param_info->value[0]; @@ -888,113 +1014,646 @@ exit_set_chap: return rc; } + +static int qla4xxx_get_host_stats(struct Scsi_Host *shost, char *buf, int len) +{ + struct scsi_qla_host *ha = to_qla_host(shost); + struct iscsi_offload_host_stats *host_stats = NULL; + int host_stats_size; + int ret = 0; + int ddb_idx = 0; + struct ql_iscsi_stats *ql_iscsi_stats = NULL; + int stats_size; + dma_addr_t iscsi_stats_dma; + + DEBUG2(ql4_printk(KERN_INFO, ha, "Func: %s\n", __func__)); + + host_stats_size = sizeof(struct iscsi_offload_host_stats); + + if (host_stats_size != len) { + ql4_printk(KERN_INFO, ha, "%s: host_stats size mismatch expected = %d, is = %d\n", + __func__, len, host_stats_size); + ret = -EINVAL; + goto exit_host_stats; + } + host_stats = (struct iscsi_offload_host_stats *)buf; + + if (!buf) { + ret = -ENOMEM; + goto exit_host_stats; + } + + stats_size = PAGE_ALIGN(sizeof(struct ql_iscsi_stats)); + + ql_iscsi_stats = dma_alloc_coherent(&ha->pdev->dev, stats_size, + &iscsi_stats_dma, GFP_KERNEL); + if (!ql_iscsi_stats) { + ql4_printk(KERN_ERR, ha, + "Unable to allocate memory for iscsi stats\n"); + goto exit_host_stats; + } + + ret = qla4xxx_get_mgmt_data(ha, ddb_idx, stats_size, + iscsi_stats_dma); + if (ret != QLA_SUCCESS) { + ql4_printk(KERN_ERR, ha, + "Unable to retrieve iscsi stats\n"); + goto exit_host_stats; + } + host_stats->mactx_frames = le64_to_cpu(ql_iscsi_stats->mac_tx_frames); + host_stats->mactx_bytes = le64_to_cpu(ql_iscsi_stats->mac_tx_bytes); + host_stats->mactx_multicast_frames = + le64_to_cpu(ql_iscsi_stats->mac_tx_multicast_frames); + host_stats->mactx_broadcast_frames = + le64_to_cpu(ql_iscsi_stats->mac_tx_broadcast_frames); + host_stats->mactx_pause_frames = + le64_to_cpu(ql_iscsi_stats->mac_tx_pause_frames); + host_stats->mactx_control_frames = + le64_to_cpu(ql_iscsi_stats->mac_tx_control_frames); + host_stats->mactx_deferral = + le64_to_cpu(ql_iscsi_stats->mac_tx_deferral); + host_stats->mactx_excess_deferral = + le64_to_cpu(ql_iscsi_stats->mac_tx_excess_deferral); + host_stats->mactx_late_collision = + le64_to_cpu(ql_iscsi_stats->mac_tx_late_collision); + host_stats->mactx_abort = le64_to_cpu(ql_iscsi_stats->mac_tx_abort); + host_stats->mactx_single_collision = + le64_to_cpu(ql_iscsi_stats->mac_tx_single_collision); + host_stats->mactx_multiple_collision = + le64_to_cpu(ql_iscsi_stats->mac_tx_multiple_collision); + host_stats->mactx_collision = + le64_to_cpu(ql_iscsi_stats->mac_tx_collision); + host_stats->mactx_frames_dropped = + le64_to_cpu(ql_iscsi_stats->mac_tx_frames_dropped); + host_stats->mactx_jumbo_frames = + le64_to_cpu(ql_iscsi_stats->mac_tx_jumbo_frames); + host_stats->macrx_frames = le64_to_cpu(ql_iscsi_stats->mac_rx_frames); + host_stats->macrx_bytes = le64_to_cpu(ql_iscsi_stats->mac_rx_bytes); + host_stats->macrx_unknown_control_frames = + le64_to_cpu(ql_iscsi_stats->mac_rx_unknown_control_frames); + host_stats->macrx_pause_frames = + le64_to_cpu(ql_iscsi_stats->mac_rx_pause_frames); + host_stats->macrx_control_frames = + le64_to_cpu(ql_iscsi_stats->mac_rx_control_frames); + host_stats->macrx_dribble = + le64_to_cpu(ql_iscsi_stats->mac_rx_dribble); + host_stats->macrx_frame_length_error = + le64_to_cpu(ql_iscsi_stats->mac_rx_frame_length_error); + host_stats->macrx_jabber = le64_to_cpu(ql_iscsi_stats->mac_rx_jabber); + host_stats->macrx_carrier_sense_error = + le64_to_cpu(ql_iscsi_stats->mac_rx_carrier_sense_error); + host_stats->macrx_frame_discarded = + le64_to_cpu(ql_iscsi_stats->mac_rx_frame_discarded); + host_stats->macrx_frames_dropped = + le64_to_cpu(ql_iscsi_stats->mac_rx_frames_dropped); + host_stats->mac_crc_error = le64_to_cpu(ql_iscsi_stats->mac_crc_error); + host_stats->mac_encoding_error = + le64_to_cpu(ql_iscsi_stats->mac_encoding_error); + host_stats->macrx_length_error_large = + le64_to_cpu(ql_iscsi_stats->mac_rx_length_error_large); + host_stats->macrx_length_error_small = + le64_to_cpu(ql_iscsi_stats->mac_rx_length_error_small); + host_stats->macrx_multicast_frames = + le64_to_cpu(ql_iscsi_stats->mac_rx_multicast_frames); + host_stats->macrx_broadcast_frames = + le64_to_cpu(ql_iscsi_stats->mac_rx_broadcast_frames); + host_stats->iptx_packets = le64_to_cpu(ql_iscsi_stats->ip_tx_packets); + host_stats->iptx_bytes = le64_to_cpu(ql_iscsi_stats->ip_tx_bytes); + host_stats->iptx_fragments = + le64_to_cpu(ql_iscsi_stats->ip_tx_fragments); + host_stats->iprx_packets = le64_to_cpu(ql_iscsi_stats->ip_rx_packets); + host_stats->iprx_bytes = le64_to_cpu(ql_iscsi_stats->ip_rx_bytes); + host_stats->iprx_fragments = + le64_to_cpu(ql_iscsi_stats->ip_rx_fragments); + host_stats->ip_datagram_reassembly = + le64_to_cpu(ql_iscsi_stats->ip_datagram_reassembly); + host_stats->ip_invalid_address_error = + le64_to_cpu(ql_iscsi_stats->ip_invalid_address_error); + host_stats->ip_error_packets = + le64_to_cpu(ql_iscsi_stats->ip_error_packets); + host_stats->ip_fragrx_overlap = + le64_to_cpu(ql_iscsi_stats->ip_fragrx_overlap); + host_stats->ip_fragrx_outoforder = + le64_to_cpu(ql_iscsi_stats->ip_fragrx_outoforder); + host_stats->ip_datagram_reassembly_timeout = + le64_to_cpu(ql_iscsi_stats->ip_datagram_reassembly_timeout); + host_stats->ipv6tx_packets = + le64_to_cpu(ql_iscsi_stats->ipv6_tx_packets); + host_stats->ipv6tx_bytes = le64_to_cpu(ql_iscsi_stats->ipv6_tx_bytes); + host_stats->ipv6tx_fragments = + le64_to_cpu(ql_iscsi_stats->ipv6_tx_fragments); + host_stats->ipv6rx_packets = + le64_to_cpu(ql_iscsi_stats->ipv6_rx_packets); + host_stats->ipv6rx_bytes = le64_to_cpu(ql_iscsi_stats->ipv6_rx_bytes); + host_stats->ipv6rx_fragments = + le64_to_cpu(ql_iscsi_stats->ipv6_rx_fragments); + host_stats->ipv6_datagram_reassembly = + le64_to_cpu(ql_iscsi_stats->ipv6_datagram_reassembly); + host_stats->ipv6_invalid_address_error = + le64_to_cpu(ql_iscsi_stats->ipv6_invalid_address_error); + host_stats->ipv6_error_packets = + le64_to_cpu(ql_iscsi_stats->ipv6_error_packets); + host_stats->ipv6_fragrx_overlap = + le64_to_cpu(ql_iscsi_stats->ipv6_fragrx_overlap); + host_stats->ipv6_fragrx_outoforder = + le64_to_cpu(ql_iscsi_stats->ipv6_fragrx_outoforder); + host_stats->ipv6_datagram_reassembly_timeout = + le64_to_cpu(ql_iscsi_stats->ipv6_datagram_reassembly_timeout); + host_stats->tcptx_segments = + le64_to_cpu(ql_iscsi_stats->tcp_tx_segments); + host_stats->tcptx_bytes = le64_to_cpu(ql_iscsi_stats->tcp_tx_bytes); + host_stats->tcprx_segments = + le64_to_cpu(ql_iscsi_stats->tcp_rx_segments); + host_stats->tcprx_byte = le64_to_cpu(ql_iscsi_stats->tcp_rx_byte); + host_stats->tcp_duplicate_ack_retx = + le64_to_cpu(ql_iscsi_stats->tcp_duplicate_ack_retx); + host_stats->tcp_retx_timer_expired = + le64_to_cpu(ql_iscsi_stats->tcp_retx_timer_expired); + host_stats->tcprx_duplicate_ack = + le64_to_cpu(ql_iscsi_stats->tcp_rx_duplicate_ack); + host_stats->tcprx_pure_ackr = + le64_to_cpu(ql_iscsi_stats->tcp_rx_pure_ackr); + host_stats->tcptx_delayed_ack = + le64_to_cpu(ql_iscsi_stats->tcp_tx_delayed_ack); + host_stats->tcptx_pure_ack = + le64_to_cpu(ql_iscsi_stats->tcp_tx_pure_ack); + host_stats->tcprx_segment_error = + le64_to_cpu(ql_iscsi_stats->tcp_rx_segment_error); + host_stats->tcprx_segment_outoforder = + le64_to_cpu(ql_iscsi_stats->tcp_rx_segment_outoforder); + host_stats->tcprx_window_probe = + le64_to_cpu(ql_iscsi_stats->tcp_rx_window_probe); + host_stats->tcprx_window_update = + le64_to_cpu(ql_iscsi_stats->tcp_rx_window_update); + host_stats->tcptx_window_probe_persist = + le64_to_cpu(ql_iscsi_stats->tcp_tx_window_probe_persist); + host_stats->ecc_error_correction = + le64_to_cpu(ql_iscsi_stats->ecc_error_correction); + host_stats->iscsi_pdu_tx = le64_to_cpu(ql_iscsi_stats->iscsi_pdu_tx); + host_stats->iscsi_data_bytes_tx = + le64_to_cpu(ql_iscsi_stats->iscsi_data_bytes_tx); + host_stats->iscsi_pdu_rx = le64_to_cpu(ql_iscsi_stats->iscsi_pdu_rx); + host_stats->iscsi_data_bytes_rx = + le64_to_cpu(ql_iscsi_stats->iscsi_data_bytes_rx); + host_stats->iscsi_io_completed = + le64_to_cpu(ql_iscsi_stats->iscsi_io_completed); + host_stats->iscsi_unexpected_io_rx = + le64_to_cpu(ql_iscsi_stats->iscsi_unexpected_io_rx); + host_stats->iscsi_format_error = + le64_to_cpu(ql_iscsi_stats->iscsi_format_error); + host_stats->iscsi_hdr_digest_error = + le64_to_cpu(ql_iscsi_stats->iscsi_hdr_digest_error); + host_stats->iscsi_data_digest_error = + le64_to_cpu(ql_iscsi_stats->iscsi_data_digest_error); + host_stats->iscsi_sequence_error = + le64_to_cpu(ql_iscsi_stats->iscsi_sequence_error); +exit_host_stats: + if (ql_iscsi_stats) + dma_free_coherent(&ha->pdev->dev, host_stats_size, + ql_iscsi_stats, iscsi_stats_dma); + + ql4_printk(KERN_INFO, ha, "%s: Get host stats done\n", + __func__); + return ret; +} + static int qla4xxx_get_iface_param(struct iscsi_iface *iface, enum iscsi_param_type param_type, int param, char *buf) { struct Scsi_Host *shost = iscsi_iface_to_shost(iface); struct scsi_qla_host *ha = to_qla_host(shost); + int ival; + char *pval = NULL; int len = -ENOSYS; - if (param_type != ISCSI_NET_PARAM) - return -ENOSYS; + if (param_type == ISCSI_NET_PARAM) { + switch (param) { + case ISCSI_NET_PARAM_IPV4_ADDR: + len = sprintf(buf, "%pI4\n", &ha->ip_config.ip_address); + break; + case ISCSI_NET_PARAM_IPV4_SUBNET: + len = sprintf(buf, "%pI4\n", + &ha->ip_config.subnet_mask); + break; + case ISCSI_NET_PARAM_IPV4_GW: + len = sprintf(buf, "%pI4\n", &ha->ip_config.gateway); + break; + case ISCSI_NET_PARAM_IFACE_ENABLE: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_IPV4_PROTOCOL_ENABLE, pval); + } else { + OP_STATE(ha->ip_config.ipv6_options, + IPV6_OPT_IPV6_PROTOCOL_ENABLE, pval); + } - switch (param) { - case ISCSI_NET_PARAM_IPV4_ADDR: - len = sprintf(buf, "%pI4\n", &ha->ip_config.ip_address); - break; - case ISCSI_NET_PARAM_IPV4_SUBNET: - len = sprintf(buf, "%pI4\n", &ha->ip_config.subnet_mask); - break; - case ISCSI_NET_PARAM_IPV4_GW: - len = sprintf(buf, "%pI4\n", &ha->ip_config.gateway); - break; - case ISCSI_NET_PARAM_IFACE_ENABLE: - if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) - len = sprintf(buf, "%s\n", - (ha->ip_config.ipv4_options & - IPOPT_IPV4_PROTOCOL_ENABLE) ? - "enabled" : "disabled"); - else if (iface->iface_type == ISCSI_IFACE_TYPE_IPV6) + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_BOOTPROTO: len = sprintf(buf, "%s\n", - (ha->ip_config.ipv6_options & - IPV6_OPT_IPV6_PROTOCOL_ENABLE) ? - "enabled" : "disabled"); - break; - case ISCSI_NET_PARAM_IPV4_BOOTPROTO: - len = sprintf(buf, "%s\n", - (ha->ip_config.tcp_options & TCPOPT_DHCP_ENABLE) ? - "dhcp" : "static"); - break; - case ISCSI_NET_PARAM_IPV6_ADDR: - if (iface->iface_num == 0) - len = sprintf(buf, "%pI6\n", &ha->ip_config.ipv6_addr0); - if (iface->iface_num == 1) - len = sprintf(buf, "%pI6\n", &ha->ip_config.ipv6_addr1); - break; - case ISCSI_NET_PARAM_IPV6_LINKLOCAL: - len = sprintf(buf, "%pI6\n", - &ha->ip_config.ipv6_link_local_addr); - break; - case ISCSI_NET_PARAM_IPV6_ROUTER: - len = sprintf(buf, "%pI6\n", - &ha->ip_config.ipv6_default_router_addr); - break; - case ISCSI_NET_PARAM_IPV6_ADDR_AUTOCFG: - len = sprintf(buf, "%s\n", - (ha->ip_config.ipv6_addl_options & - IPV6_ADDOPT_NEIGHBOR_DISCOVERY_ADDR_ENABLE) ? - "nd" : "static"); - break; - case ISCSI_NET_PARAM_IPV6_LINKLOCAL_AUTOCFG: - len = sprintf(buf, "%s\n", - (ha->ip_config.ipv6_addl_options & - IPV6_ADDOPT_AUTOCONFIG_LINK_LOCAL_ADDR) ? - "auto" : "static"); - break; - case ISCSI_NET_PARAM_VLAN_ID: - if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + (ha->ip_config.tcp_options & + TCPOPT_DHCP_ENABLE) ? + "dhcp" : "static"); + break; + case ISCSI_NET_PARAM_IPV6_ADDR: + if (iface->iface_num == 0) + len = sprintf(buf, "%pI6\n", + &ha->ip_config.ipv6_addr0); + if (iface->iface_num == 1) + len = sprintf(buf, "%pI6\n", + &ha->ip_config.ipv6_addr1); + break; + case ISCSI_NET_PARAM_IPV6_LINKLOCAL: + len = sprintf(buf, "%pI6\n", + &ha->ip_config.ipv6_link_local_addr); + break; + case ISCSI_NET_PARAM_IPV6_ROUTER: + len = sprintf(buf, "%pI6\n", + &ha->ip_config.ipv6_default_router_addr); + break; + case ISCSI_NET_PARAM_IPV6_ADDR_AUTOCFG: + pval = (ha->ip_config.ipv6_addl_options & + IPV6_ADDOPT_NEIGHBOR_DISCOVERY_ADDR_ENABLE) ? + "nd" : "static"; + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV6_LINKLOCAL_AUTOCFG: + pval = (ha->ip_config.ipv6_addl_options & + IPV6_ADDOPT_AUTOCONFIG_LINK_LOCAL_ADDR) ? + "auto" : "static"; + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_VLAN_ID: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + ival = ha->ip_config.ipv4_vlan_tag & + ISCSI_MAX_VLAN_ID; + else + ival = ha->ip_config.ipv6_vlan_tag & + ISCSI_MAX_VLAN_ID; + + len = sprintf(buf, "%d\n", ival); + break; + case ISCSI_NET_PARAM_VLAN_PRIORITY: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + ival = (ha->ip_config.ipv4_vlan_tag >> 13) & + ISCSI_MAX_VLAN_PRIORITY; + else + ival = (ha->ip_config.ipv6_vlan_tag >> 13) & + ISCSI_MAX_VLAN_PRIORITY; + + len = sprintf(buf, "%d\n", ival); + break; + case ISCSI_NET_PARAM_VLAN_ENABLED: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_VLAN_TAGGING_ENABLE, pval); + } else { + OP_STATE(ha->ip_config.ipv6_options, + IPV6_OPT_VLAN_TAGGING_ENABLE, pval); + } + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_MTU: + len = sprintf(buf, "%d\n", ha->ip_config.eth_mtu_size); + break; + case ISCSI_NET_PARAM_PORT: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + len = sprintf(buf, "%d\n", + ha->ip_config.ipv4_port); + else + len = sprintf(buf, "%d\n", + ha->ip_config.ipv6_port); + break; + case ISCSI_NET_PARAM_IPADDR_STATE: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + pval = iscsi_get_ipaddress_state_name( + ha->ip_config.ipv4_addr_state); + } else { + if (iface->iface_num == 0) + pval = iscsi_get_ipaddress_state_name( + ha->ip_config.ipv6_addr0_state); + else if (iface->iface_num == 1) + pval = iscsi_get_ipaddress_state_name( + ha->ip_config.ipv6_addr1_state); + } + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV6_LINKLOCAL_STATE: + pval = iscsi_get_ipaddress_state_name( + ha->ip_config.ipv6_link_local_state); + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV6_ROUTER_STATE: + pval = iscsi_get_router_state_name( + ha->ip_config.ipv6_default_router_state); + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_DELAYED_ACK_EN: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + OP_STATE(~ha->ip_config.tcp_options, + TCPOPT_DELAYED_ACK_DISABLE, pval); + } else { + OP_STATE(~ha->ip_config.ipv6_tcp_options, + IPV6_TCPOPT_DELAYED_ACK_DISABLE, pval); + } + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_TCP_NAGLE_DISABLE: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + OP_STATE(~ha->ip_config.tcp_options, + TCPOPT_NAGLE_ALGO_DISABLE, pval); + } else { + OP_STATE(~ha->ip_config.ipv6_tcp_options, + IPV6_TCPOPT_NAGLE_ALGO_DISABLE, pval); + } + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_TCP_WSF_DISABLE: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + OP_STATE(~ha->ip_config.tcp_options, + TCPOPT_WINDOW_SCALE_DISABLE, pval); + } else { + OP_STATE(~ha->ip_config.ipv6_tcp_options, + IPV6_TCPOPT_WINDOW_SCALE_DISABLE, + pval); + } + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_TCP_WSF: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + len = sprintf(buf, "%d\n", + ha->ip_config.tcp_wsf); + else + len = sprintf(buf, "%d\n", + ha->ip_config.ipv6_tcp_wsf); + break; + case ISCSI_NET_PARAM_TCP_TIMER_SCALE: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + ival = (ha->ip_config.tcp_options & + TCPOPT_TIMER_SCALE) >> 1; + else + ival = (ha->ip_config.ipv6_tcp_options & + IPV6_TCPOPT_TIMER_SCALE) >> 1; + + len = sprintf(buf, "%d\n", ival); + break; + case ISCSI_NET_PARAM_TCP_TIMESTAMP_EN: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + OP_STATE(ha->ip_config.tcp_options, + TCPOPT_TIMESTAMP_ENABLE, pval); + } else { + OP_STATE(ha->ip_config.ipv6_tcp_options, + IPV6_TCPOPT_TIMESTAMP_EN, pval); + } + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_CACHE_ID: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + len = sprintf(buf, "%d\n", + ha->ip_config.ipv4_cache_id); + else + len = sprintf(buf, "%d\n", + ha->ip_config.ipv6_cache_id); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_DNS_ADDR_EN: + OP_STATE(ha->ip_config.tcp_options, + TCPOPT_DNS_SERVER_IP_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_SLP_DA_EN: + OP_STATE(ha->ip_config.tcp_options, + TCPOPT_SLP_DA_INFO_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_TOS_EN: + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_IPV4_TOS_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_TOS: + len = sprintf(buf, "%d\n", ha->ip_config.ipv4_tos); + break; + case ISCSI_NET_PARAM_IPV4_GRAT_ARP_EN: + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_GRAT_ARP_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID_EN: + OP_STATE(ha->ip_config.ipv4_options, IPOPT_ALT_CID_EN, + pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID: + pval = (ha->ip_config.ipv4_alt_cid_len) ? + (char *)ha->ip_config.ipv4_alt_cid : ""; + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_REQ_VENDOR_ID_EN: + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_REQ_VID_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_USE_VENDOR_ID_EN: + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_USE_VID_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_VENDOR_ID: + pval = (ha->ip_config.ipv4_vid_len) ? + (char *)ha->ip_config.ipv4_vid : ""; + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_LEARN_IQN_EN: + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_LEARN_IQN_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_FRAGMENT_DISABLE: + OP_STATE(~ha->ip_config.ipv4_options, + IPOPT_FRAGMENTATION_DISABLE, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_IN_FORWARD_EN: + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_IN_FORWARD_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_REDIRECT_EN: + if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { + OP_STATE(ha->ip_config.ipv4_options, + IPOPT_ARP_REDIRECT_EN, pval); + } else { + OP_STATE(ha->ip_config.ipv6_options, + IPV6_OPT_REDIRECT_EN, pval); + } + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV4_TTL: + len = sprintf(buf, "%d\n", ha->ip_config.ipv4_ttl); + break; + case ISCSI_NET_PARAM_IPV6_GRAT_NEIGHBOR_ADV_EN: + OP_STATE(ha->ip_config.ipv6_options, + IPV6_OPT_GRAT_NEIGHBOR_ADV_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV6_MLD_EN: + OP_STATE(ha->ip_config.ipv6_addl_options, + IPV6_ADDOPT_MLD_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_NET_PARAM_IPV6_FLOW_LABEL: + len = sprintf(buf, "%u\n", ha->ip_config.ipv6_flow_lbl); + break; + case ISCSI_NET_PARAM_IPV6_TRAFFIC_CLASS: len = sprintf(buf, "%d\n", - (ha->ip_config.ipv4_vlan_tag & - ISCSI_MAX_VLAN_ID)); - else if (iface->iface_type == ISCSI_IFACE_TYPE_IPV6) + ha->ip_config.ipv6_traffic_class); + break; + case ISCSI_NET_PARAM_IPV6_HOP_LIMIT: len = sprintf(buf, "%d\n", - (ha->ip_config.ipv6_vlan_tag & - ISCSI_MAX_VLAN_ID)); - break; - case ISCSI_NET_PARAM_VLAN_PRIORITY: - if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) + ha->ip_config.ipv6_hop_limit); + break; + case ISCSI_NET_PARAM_IPV6_ND_REACHABLE_TMO: len = sprintf(buf, "%d\n", - ((ha->ip_config.ipv4_vlan_tag >> 13) & - ISCSI_MAX_VLAN_PRIORITY)); - else if (iface->iface_type == ISCSI_IFACE_TYPE_IPV6) + ha->ip_config.ipv6_nd_reach_time); + break; + case ISCSI_NET_PARAM_IPV6_ND_REXMIT_TIME: len = sprintf(buf, "%d\n", - ((ha->ip_config.ipv6_vlan_tag >> 13) & - ISCSI_MAX_VLAN_PRIORITY)); - break; - case ISCSI_NET_PARAM_VLAN_ENABLED: - if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) - len = sprintf(buf, "%s\n", - (ha->ip_config.ipv4_options & - IPOPT_VLAN_TAGGING_ENABLE) ? - "enabled" : "disabled"); - else if (iface->iface_type == ISCSI_IFACE_TYPE_IPV6) - len = sprintf(buf, "%s\n", - (ha->ip_config.ipv6_options & - IPV6_OPT_VLAN_TAGGING_ENABLE) ? - "enabled" : "disabled"); - break; - case ISCSI_NET_PARAM_MTU: - len = sprintf(buf, "%d\n", ha->ip_config.eth_mtu_size); - break; - case ISCSI_NET_PARAM_PORT: - if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) - len = sprintf(buf, "%d\n", ha->ip_config.ipv4_port); - else if (iface->iface_type == ISCSI_IFACE_TYPE_IPV6) - len = sprintf(buf, "%d\n", ha->ip_config.ipv6_port); - break; - default: - len = -ENOSYS; + ha->ip_config.ipv6_nd_rexmit_timer); + break; + case ISCSI_NET_PARAM_IPV6_ND_STALE_TMO: + len = sprintf(buf, "%d\n", + ha->ip_config.ipv6_nd_stale_timeout); + break; + case ISCSI_NET_PARAM_IPV6_DUP_ADDR_DETECT_CNT: + len = sprintf(buf, "%d\n", + ha->ip_config.ipv6_dup_addr_detect_count); + break; + case ISCSI_NET_PARAM_IPV6_RTR_ADV_LINK_MTU: + len = sprintf(buf, "%d\n", + ha->ip_config.ipv6_gw_advrt_mtu); + break; + default: + len = -ENOSYS; + } + } else if (param_type == ISCSI_IFACE_PARAM) { + switch (param) { + case ISCSI_IFACE_PARAM_DEF_TASKMGMT_TMO: + len = sprintf(buf, "%d\n", ha->ip_config.def_timeout); + break; + case ISCSI_IFACE_PARAM_HDRDGST_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_HEADER_DIGEST_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_DATADGST_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_DATA_DIGEST_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_IMM_DATA_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_IMMEDIATE_DATA_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_INITIAL_R2T_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_INITIAL_R2T_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_DATASEQ_INORDER_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_DATA_SEQ_INORDER_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_PDU_INORDER_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_DATA_PDU_INORDER_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_ERL: + len = sprintf(buf, "%d\n", + (ha->ip_config.iscsi_options & + ISCSIOPTS_ERL)); + break; + case ISCSI_IFACE_PARAM_MAX_RECV_DLENGTH: + len = sprintf(buf, "%u\n", + ha->ip_config.iscsi_max_pdu_size * + BYTE_UNITS); + break; + case ISCSI_IFACE_PARAM_FIRST_BURST: + len = sprintf(buf, "%u\n", + ha->ip_config.iscsi_first_burst_len * + BYTE_UNITS); + break; + case ISCSI_IFACE_PARAM_MAX_R2T: + len = sprintf(buf, "%d\n", + ha->ip_config.iscsi_max_outstnd_r2t); + break; + case ISCSI_IFACE_PARAM_MAX_BURST: + len = sprintf(buf, "%u\n", + ha->ip_config.iscsi_max_burst_len * + BYTE_UNITS); + break; + case ISCSI_IFACE_PARAM_CHAP_AUTH_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_CHAP_AUTH_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_BIDI_CHAP_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_BIDI_CHAP_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_DISCOVERY_AUTH_OPTIONAL: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_DISCOVERY_AUTH_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_DISCOVERY_LOGOUT_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_DISCOVERY_LOGOUT_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_STRICT_LOGIN_COMP_EN: + OP_STATE(ha->ip_config.iscsi_options, + ISCSIOPTS_STRICT_LOGIN_COMP_EN, pval); + + len = sprintf(buf, "%s\n", pval); + break; + case ISCSI_IFACE_PARAM_INITIATOR_NAME: + len = sprintf(buf, "%s\n", ha->ip_config.iscsi_name); + break; + default: + len = -ENOSYS; + } } return len; @@ -1366,8 +2025,8 @@ static void qla4xxx_set_ipv6(struct scsi_qla_host *ha, cpu_to_le16( IPV6_ADDOPT_NEIGHBOR_DISCOVERY_ADDR_ENABLE); else - ql4_printk(KERN_ERR, ha, "Invalid autocfg setting for " - "IPv6 addr\n"); + ql4_printk(KERN_ERR, ha, + "Invalid autocfg setting for IPv6 addr\n"); break; case ISCSI_NET_PARAM_IPV6_LINKLOCAL_AUTOCFG: /* Autocfg applies to even interface */ @@ -1383,8 +2042,8 @@ static void qla4xxx_set_ipv6(struct scsi_qla_host *ha, init_fw_cb->ipv6_addtl_opts &= cpu_to_le16( ~IPV6_ADDOPT_AUTOCONFIG_LINK_LOCAL_ADDR); else - ql4_printk(KERN_ERR, ha, "Invalid autocfg setting for " - "IPv6 linklocal addr\n"); + ql4_printk(KERN_ERR, ha, + "Invalid autocfg setting for IPv6 linklocal addr\n"); break; case ISCSI_NET_PARAM_IPV6_ROUTER_AUTOCFG: /* Autocfg applies to even interface */ @@ -1433,6 +2092,135 @@ static void qla4xxx_set_ipv6(struct scsi_qla_host *ha, init_fw_cb->ipv6_port = cpu_to_le16(*(uint16_t *)iface_param->value); break; + case ISCSI_NET_PARAM_DELAYED_ACK_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_DISABLE) + init_fw_cb->ipv6_tcp_opts |= + cpu_to_le16(IPV6_TCPOPT_DELAYED_ACK_DISABLE); + else + init_fw_cb->ipv6_tcp_opts &= + cpu_to_le16(~IPV6_TCPOPT_DELAYED_ACK_DISABLE); + break; + case ISCSI_NET_PARAM_TCP_NAGLE_DISABLE: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_DISABLE) + init_fw_cb->ipv6_tcp_opts |= + cpu_to_le16(IPV6_TCPOPT_NAGLE_ALGO_DISABLE); + else + init_fw_cb->ipv6_tcp_opts &= + cpu_to_le16(~IPV6_TCPOPT_NAGLE_ALGO_DISABLE); + break; + case ISCSI_NET_PARAM_TCP_WSF_DISABLE: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_DISABLE) + init_fw_cb->ipv6_tcp_opts |= + cpu_to_le16(IPV6_TCPOPT_WINDOW_SCALE_DISABLE); + else + init_fw_cb->ipv6_tcp_opts &= + cpu_to_le16(~IPV6_TCPOPT_WINDOW_SCALE_DISABLE); + break; + case ISCSI_NET_PARAM_TCP_WSF: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_tcp_wsf = iface_param->value[0]; + break; + case ISCSI_NET_PARAM_TCP_TIMER_SCALE: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_tcp_opts &= + cpu_to_le16(~IPV6_TCPOPT_TIMER_SCALE); + init_fw_cb->ipv6_tcp_opts |= + cpu_to_le16((iface_param->value[0] << 1) & + IPV6_TCPOPT_TIMER_SCALE); + break; + case ISCSI_NET_PARAM_TCP_TIMESTAMP_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv6_tcp_opts |= + cpu_to_le16(IPV6_TCPOPT_TIMESTAMP_EN); + else + init_fw_cb->ipv6_tcp_opts &= + cpu_to_le16(~IPV6_TCPOPT_TIMESTAMP_EN); + break; + case ISCSI_NET_PARAM_IPV6_GRAT_NEIGHBOR_ADV_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv6_opts |= + cpu_to_le16(IPV6_OPT_GRAT_NEIGHBOR_ADV_EN); + else + init_fw_cb->ipv6_opts &= + cpu_to_le16(~IPV6_OPT_GRAT_NEIGHBOR_ADV_EN); + break; + case ISCSI_NET_PARAM_REDIRECT_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv6_opts |= + cpu_to_le16(IPV6_OPT_REDIRECT_EN); + else + init_fw_cb->ipv6_opts &= + cpu_to_le16(~IPV6_OPT_REDIRECT_EN); + break; + case ISCSI_NET_PARAM_IPV6_MLD_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv6_addtl_opts |= + cpu_to_le16(IPV6_ADDOPT_MLD_EN); + else + init_fw_cb->ipv6_addtl_opts &= + cpu_to_le16(~IPV6_ADDOPT_MLD_EN); + break; + case ISCSI_NET_PARAM_IPV6_FLOW_LABEL: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_flow_lbl = + cpu_to_le16(*(uint16_t *)iface_param->value); + break; + case ISCSI_NET_PARAM_IPV6_TRAFFIC_CLASS: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_traffic_class = iface_param->value[0]; + break; + case ISCSI_NET_PARAM_IPV6_HOP_LIMIT: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_hop_limit = iface_param->value[0]; + break; + case ISCSI_NET_PARAM_IPV6_ND_REACHABLE_TMO: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_nd_reach_time = + cpu_to_le32(*(uint32_t *)iface_param->value); + break; + case ISCSI_NET_PARAM_IPV6_ND_REXMIT_TIME: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_nd_rexmit_timer = + cpu_to_le32(*(uint32_t *)iface_param->value); + break; + case ISCSI_NET_PARAM_IPV6_ND_STALE_TMO: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_nd_stale_timeout = + cpu_to_le32(*(uint32_t *)iface_param->value); + break; + case ISCSI_NET_PARAM_IPV6_DUP_ADDR_DETECT_CNT: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_dup_addr_detect_count = iface_param->value[0]; + break; + case ISCSI_NET_PARAM_IPV6_RTR_ADV_LINK_MTU: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv6_gw_advrt_mtu = + cpu_to_le32(*(uint32_t *)iface_param->value); + break; default: ql4_printk(KERN_ERR, ha, "Unknown IPv6 param = %d\n", iface_param->param); @@ -1501,6 +2289,195 @@ static void qla4xxx_set_ipv4(struct scsi_qla_host *ha, init_fw_cb->ipv4_port = cpu_to_le16(*(uint16_t *)iface_param->value); break; + case ISCSI_NET_PARAM_DELAYED_ACK_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_DISABLE) + init_fw_cb->ipv4_tcp_opts |= + cpu_to_le16(TCPOPT_DELAYED_ACK_DISABLE); + else + init_fw_cb->ipv4_tcp_opts &= + cpu_to_le16(~TCPOPT_DELAYED_ACK_DISABLE); + break; + case ISCSI_NET_PARAM_TCP_NAGLE_DISABLE: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_DISABLE) + init_fw_cb->ipv4_tcp_opts |= + cpu_to_le16(TCPOPT_NAGLE_ALGO_DISABLE); + else + init_fw_cb->ipv4_tcp_opts &= + cpu_to_le16(~TCPOPT_NAGLE_ALGO_DISABLE); + break; + case ISCSI_NET_PARAM_TCP_WSF_DISABLE: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_DISABLE) + init_fw_cb->ipv4_tcp_opts |= + cpu_to_le16(TCPOPT_WINDOW_SCALE_DISABLE); + else + init_fw_cb->ipv4_tcp_opts &= + cpu_to_le16(~TCPOPT_WINDOW_SCALE_DISABLE); + break; + case ISCSI_NET_PARAM_TCP_WSF: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv4_tcp_wsf = iface_param->value[0]; + break; + case ISCSI_NET_PARAM_TCP_TIMER_SCALE: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv4_tcp_opts &= cpu_to_le16(~TCPOPT_TIMER_SCALE); + init_fw_cb->ipv4_tcp_opts |= + cpu_to_le16((iface_param->value[0] << 1) & + TCPOPT_TIMER_SCALE); + break; + case ISCSI_NET_PARAM_TCP_TIMESTAMP_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_tcp_opts |= + cpu_to_le16(TCPOPT_TIMESTAMP_ENABLE); + else + init_fw_cb->ipv4_tcp_opts &= + cpu_to_le16(~TCPOPT_TIMESTAMP_ENABLE); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_DNS_ADDR_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_tcp_opts |= + cpu_to_le16(TCPOPT_DNS_SERVER_IP_EN); + else + init_fw_cb->ipv4_tcp_opts &= + cpu_to_le16(~TCPOPT_DNS_SERVER_IP_EN); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_SLP_DA_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_tcp_opts |= + cpu_to_le16(TCPOPT_SLP_DA_INFO_EN); + else + init_fw_cb->ipv4_tcp_opts &= + cpu_to_le16(~TCPOPT_SLP_DA_INFO_EN); + break; + case ISCSI_NET_PARAM_IPV4_TOS_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_IPV4_TOS_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_IPV4_TOS_EN); + break; + case ISCSI_NET_PARAM_IPV4_TOS: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv4_tos = iface_param->value[0]; + break; + case ISCSI_NET_PARAM_IPV4_GRAT_ARP_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_GRAT_ARP_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_GRAT_ARP_EN); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_ALT_CID_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_ALT_CID_EN); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID: + if (iface_param->iface_num & 0x1) + break; + memcpy(init_fw_cb->ipv4_dhcp_alt_cid, iface_param->value, + (sizeof(init_fw_cb->ipv4_dhcp_alt_cid) - 1)); + init_fw_cb->ipv4_dhcp_alt_cid_len = + strlen(init_fw_cb->ipv4_dhcp_alt_cid); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_REQ_VENDOR_ID_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_REQ_VID_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_REQ_VID_EN); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_USE_VENDOR_ID_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_USE_VID_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_USE_VID_EN); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_VENDOR_ID: + if (iface_param->iface_num & 0x1) + break; + memcpy(init_fw_cb->ipv4_dhcp_vid, iface_param->value, + (sizeof(init_fw_cb->ipv4_dhcp_vid) - 1)); + init_fw_cb->ipv4_dhcp_vid_len = + strlen(init_fw_cb->ipv4_dhcp_vid); + break; + case ISCSI_NET_PARAM_IPV4_DHCP_LEARN_IQN_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_LEARN_IQN_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_LEARN_IQN_EN); + break; + case ISCSI_NET_PARAM_IPV4_FRAGMENT_DISABLE: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_DISABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_FRAGMENTATION_DISABLE); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_FRAGMENTATION_DISABLE); + break; + case ISCSI_NET_PARAM_IPV4_IN_FORWARD_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_IN_FORWARD_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_IN_FORWARD_EN); + break; + case ISCSI_NET_PARAM_REDIRECT_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->ipv4_ip_opts |= + cpu_to_le16(IPOPT_ARP_REDIRECT_EN); + else + init_fw_cb->ipv4_ip_opts &= + cpu_to_le16(~IPOPT_ARP_REDIRECT_EN); + break; + case ISCSI_NET_PARAM_IPV4_TTL: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->ipv4_ttl = iface_param->value[0]; + break; default: ql4_printk(KERN_ERR, ha, "Unknown IPv4 param = %d\n", iface_param->param); @@ -1508,6 +2485,168 @@ static void qla4xxx_set_ipv4(struct scsi_qla_host *ha, } } +static void qla4xxx_set_iscsi_param(struct scsi_qla_host *ha, + struct iscsi_iface_param_info *iface_param, + struct addr_ctrl_blk *init_fw_cb) +{ + switch (iface_param->param) { + case ISCSI_IFACE_PARAM_DEF_TASKMGMT_TMO: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->def_timeout = + cpu_to_le16(*(uint16_t *)iface_param->value); + break; + case ISCSI_IFACE_PARAM_HDRDGST_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_HEADER_DIGEST_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_HEADER_DIGEST_EN); + break; + case ISCSI_IFACE_PARAM_DATADGST_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_DATA_DIGEST_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_DATA_DIGEST_EN); + break; + case ISCSI_IFACE_PARAM_IMM_DATA_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_IMMEDIATE_DATA_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_IMMEDIATE_DATA_EN); + break; + case ISCSI_IFACE_PARAM_INITIAL_R2T_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_INITIAL_R2T_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_INITIAL_R2T_EN); + break; + case ISCSI_IFACE_PARAM_DATASEQ_INORDER_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_DATA_SEQ_INORDER_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_DATA_SEQ_INORDER_EN); + break; + case ISCSI_IFACE_PARAM_PDU_INORDER_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_DATA_PDU_INORDER_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_DATA_PDU_INORDER_EN); + break; + case ISCSI_IFACE_PARAM_ERL: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->iscsi_opts &= cpu_to_le16(~ISCSIOPTS_ERL); + init_fw_cb->iscsi_opts |= cpu_to_le16(iface_param->value[0] & + ISCSIOPTS_ERL); + break; + case ISCSI_IFACE_PARAM_MAX_RECV_DLENGTH: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->iscsi_max_pdu_size = + cpu_to_le32(*(uint32_t *)iface_param->value) / + BYTE_UNITS; + break; + case ISCSI_IFACE_PARAM_FIRST_BURST: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->iscsi_fburst_len = + cpu_to_le32(*(uint32_t *)iface_param->value) / + BYTE_UNITS; + break; + case ISCSI_IFACE_PARAM_MAX_R2T: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->iscsi_max_outstnd_r2t = + cpu_to_le16(*(uint16_t *)iface_param->value); + break; + case ISCSI_IFACE_PARAM_MAX_BURST: + if (iface_param->iface_num & 0x1) + break; + init_fw_cb->iscsi_max_burst_len = + cpu_to_le32(*(uint32_t *)iface_param->value) / + BYTE_UNITS; + break; + case ISCSI_IFACE_PARAM_CHAP_AUTH_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_CHAP_AUTH_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_CHAP_AUTH_EN); + break; + case ISCSI_IFACE_PARAM_BIDI_CHAP_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_BIDI_CHAP_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_BIDI_CHAP_EN); + break; + case ISCSI_IFACE_PARAM_DISCOVERY_AUTH_OPTIONAL: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_DISCOVERY_AUTH_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_DISCOVERY_AUTH_EN); + break; + case ISCSI_IFACE_PARAM_DISCOVERY_LOGOUT_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_DISCOVERY_LOGOUT_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_DISCOVERY_LOGOUT_EN); + break; + case ISCSI_IFACE_PARAM_STRICT_LOGIN_COMP_EN: + if (iface_param->iface_num & 0x1) + break; + if (iface_param->value[0] == ISCSI_NET_PARAM_ENABLE) + init_fw_cb->iscsi_opts |= + cpu_to_le16(ISCSIOPTS_STRICT_LOGIN_COMP_EN); + else + init_fw_cb->iscsi_opts &= + cpu_to_le16(~ISCSIOPTS_STRICT_LOGIN_COMP_EN); + break; + default: + ql4_printk(KERN_ERR, ha, "Unknown iscsi param = %d\n", + iface_param->param); + break; + } +} + static void qla4xxx_initcb_to_acb(struct addr_ctrl_blk *init_fw_cb) { @@ -1565,40 +2704,47 @@ qla4xxx_iface_set_param(struct Scsi_Host *shost, void *data, uint32_t len) nla_for_each_attr(attr, data, len, rem) { iface_param = nla_data(attr); - if (iface_param->param_type != ISCSI_NET_PARAM) - continue; - - switch (iface_param->iface_type) { - case ISCSI_IFACE_TYPE_IPV4: - switch (iface_param->iface_num) { - case 0: - qla4xxx_set_ipv4(ha, iface_param, init_fw_cb); - break; - default: + if (iface_param->param_type == ISCSI_NET_PARAM) { + switch (iface_param->iface_type) { + case ISCSI_IFACE_TYPE_IPV4: + switch (iface_param->iface_num) { + case 0: + qla4xxx_set_ipv4(ha, iface_param, + init_fw_cb); + break; + default: /* Cannot have more than one IPv4 interface */ - ql4_printk(KERN_ERR, ha, "Invalid IPv4 iface " - "number = %d\n", - iface_param->iface_num); + ql4_printk(KERN_ERR, ha, + "Invalid IPv4 iface number = %d\n", + iface_param->iface_num); + break; + } break; - } - break; - case ISCSI_IFACE_TYPE_IPV6: - switch (iface_param->iface_num) { - case 0: - case 1: - qla4xxx_set_ipv6(ha, iface_param, init_fw_cb); + case ISCSI_IFACE_TYPE_IPV6: + switch (iface_param->iface_num) { + case 0: + case 1: + qla4xxx_set_ipv6(ha, iface_param, + init_fw_cb); + break; + default: + /* Cannot have more than two IPv6 interface */ + ql4_printk(KERN_ERR, ha, + "Invalid IPv6 iface number = %d\n", + iface_param->iface_num); + break; + } break; default: - /* Cannot have more than two IPv6 interface */ - ql4_printk(KERN_ERR, ha, "Invalid IPv6 iface " - "number = %d\n", - iface_param->iface_num); + ql4_printk(KERN_ERR, ha, + "Invalid iface type\n"); break; } - break; - default: - ql4_printk(KERN_ERR, ha, "Invalid iface type\n"); - break; + } else if (iface_param->param_type == ISCSI_IFACE_PARAM) { + qla4xxx_set_iscsi_param(ha, iface_param, + init_fw_cb); + } else { + continue; } } @@ -2538,6 +3684,7 @@ static void qla4xxx_copy_to_sess_conn_params(struct iscsi_conn *conn, unsigned long options = 0; uint16_t ddb_link; uint16_t disc_parent; + char ip_addr[DDB_IPADDR_LEN]; options = le16_to_cpu(fw_ddb_entry->options); conn->is_fw_assigned_ipv6 = test_bit(OPT_IS_FW_ASSIGNED_IPV6, &options); @@ -2619,6 +3766,14 @@ static void qla4xxx_copy_to_sess_conn_params(struct iscsi_conn *conn, iscsi_set_param(conn->cls_conn, ISCSI_PARAM_TARGET_ALIAS, (char *)fw_ddb_entry->iscsi_alias, 0); + + options = le16_to_cpu(fw_ddb_entry->options); + if (options & DDB_OPT_IPV6_DEVICE) { + memset(ip_addr, 0, sizeof(ip_addr)); + sprintf(ip_addr, "%pI6", fw_ddb_entry->link_local_ipv6_addr); + iscsi_set_param(conn->cls_conn, ISCSI_PARAM_LOCAL_IPADDR, + (char *)ip_addr, 0); + } } static void qla4xxx_copy_fwddb_param(struct scsi_qla_host *ha, @@ -5030,64 +6185,6 @@ kset_free: } -/** - * qla4xxx_create chap_list - Create CHAP list from FLASH - * @ha: pointer to adapter structure - * - * Read flash and make a list of CHAP entries, during login when a CHAP entry - * is received, it will be checked in this list. If entry exist then the CHAP - * entry index is set in the DDB. If CHAP entry does not exist in this list - * then a new entry is added in FLASH in CHAP table and the index obtained is - * used in the DDB. - **/ -static void qla4xxx_create_chap_list(struct scsi_qla_host *ha) -{ - int rval = 0; - uint8_t *chap_flash_data = NULL; - uint32_t offset; - dma_addr_t chap_dma; - uint32_t chap_size = 0; - - if (is_qla40XX(ha)) - chap_size = MAX_CHAP_ENTRIES_40XX * - sizeof(struct ql4_chap_table); - else /* Single region contains CHAP info for both - * ports which is divided into half for each port. - */ - chap_size = ha->hw.flt_chap_size / 2; - - chap_flash_data = dma_alloc_coherent(&ha->pdev->dev, chap_size, - &chap_dma, GFP_KERNEL); - if (!chap_flash_data) { - ql4_printk(KERN_ERR, ha, "No memory for chap_flash_data\n"); - return; - } - if (is_qla40XX(ha)) - offset = FLASH_CHAP_OFFSET; - else { - offset = FLASH_RAW_ACCESS_ADDR + (ha->hw.flt_region_chap << 2); - if (ha->port_num == 1) - offset += chap_size; - } - - rval = qla4xxx_get_flash(ha, chap_dma, offset, chap_size); - if (rval != QLA_SUCCESS) - goto exit_chap_list; - - if (ha->chap_list == NULL) - ha->chap_list = vmalloc(chap_size); - if (ha->chap_list == NULL) { - ql4_printk(KERN_ERR, ha, "No memory for ha->chap_list\n"); - goto exit_chap_list; - } - - memcpy(ha->chap_list, chap_flash_data, chap_size); - -exit_chap_list: - dma_free_coherent(&ha->pdev->dev, chap_size, - chap_flash_data, chap_dma); -} - static void qla4xxx_get_param_ddb(struct ddb_entry *ddb_entry, struct ql4_tuple_ddb *tddb) { @@ -7521,6 +8618,9 @@ static int qla4xxx_probe_adapter(struct pci_dev *pdev, mutex_init(&ha->chap_sem); init_completion(&ha->mbx_intr_comp); init_completion(&ha->disable_acb_comp); + init_completion(&ha->idc_comp); + init_completion(&ha->link_up_comp); + init_completion(&ha->disable_acb_comp); spin_lock_init(&ha->hardware_lock); spin_lock_init(&ha->work_lock); diff --git a/drivers/scsi/qla4xxx/ql4_version.h b/drivers/scsi/qla4xxx/ql4_version.h index f4fef72c9bc..9b294665868 100644 --- a/drivers/scsi/qla4xxx/ql4_version.h +++ b/drivers/scsi/qla4xxx/ql4_version.h @@ -5,4 +5,4 @@ * See LICENSE.qla4xxx for copyright and licensing details. */ -#define QLA4XXX_DRIVER_VERSION "5.04.00-k1" +#define QLA4XXX_DRIVER_VERSION "5.04.00-k3" diff --git a/drivers/scsi/scsi.c b/drivers/scsi/scsi.c index fe0bcb18fb2..d8afec8317c 100644 --- a/drivers/scsi/scsi.c +++ b/drivers/scsi/scsi.c @@ -297,6 +297,7 @@ struct scsi_cmnd *scsi_get_command(struct scsi_device *dev, gfp_t gfp_mask) cmd->device = dev; INIT_LIST_HEAD(&cmd->list); + INIT_DELAYED_WORK(&cmd->abort_work, scmd_eh_abort_handler); spin_lock_irqsave(&dev->list_lock, flags); list_add_tail(&cmd->list, &dev->cmd_list); spin_unlock_irqrestore(&dev->list_lock, flags); @@ -353,6 +354,8 @@ void scsi_put_command(struct scsi_cmnd *cmd) list_del_init(&cmd->list); spin_unlock_irqrestore(&cmd->device->list_lock, flags); + cancel_delayed_work(&cmd->abort_work); + __scsi_put_command(cmd->device->host, cmd, &sdev->sdev_gendev); } EXPORT_SYMBOL(scsi_put_command); @@ -742,15 +745,13 @@ int scsi_dispatch_cmd(struct scsi_cmnd *cmd) } /** - * scsi_done - Enqueue the finished SCSI command into the done queue. + * scsi_done - Invoke completion on finished SCSI command. * @cmd: The SCSI Command for which a low-level device driver (LLDD) gives * ownership back to SCSI Core -- i.e. the LLDD has finished with it. * * Description: This function is the mid-level's (SCSI Core) interrupt routine, * which regains ownership of the SCSI command (de facto) from a LLDD, and - * enqueues the command to the done queue for further processing. - * - * This is the producer of the done queue who enqueues at the tail. + * calls blk_complete_request() for further processing. * * This function is interrupt context safe. */ diff --git a/drivers/scsi/scsi_debug.c b/drivers/scsi/scsi_debug.c index 80b8b10edf4..2decc641751 100644 --- a/drivers/scsi/scsi_debug.c +++ b/drivers/scsi/scsi_debug.c @@ -2873,13 +2873,13 @@ static int scsi_debug_show_info(struct seq_file *m, struct Scsi_Host *host) return 0; } -static ssize_t sdebug_delay_show(struct device_driver * ddp, char * buf) +static ssize_t delay_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_delay); } -static ssize_t sdebug_delay_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t delay_store(struct device_driver *ddp, const char *buf, + size_t count) { int delay; char work[20]; @@ -2892,16 +2892,15 @@ static ssize_t sdebug_delay_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(delay, S_IRUGO | S_IWUSR, sdebug_delay_show, - sdebug_delay_store); +static DRIVER_ATTR_RW(delay); -static ssize_t sdebug_opts_show(struct device_driver * ddp, char * buf) +static ssize_t opts_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "0x%x\n", scsi_debug_opts); } -static ssize_t sdebug_opts_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t opts_store(struct device_driver *ddp, const char *buf, + size_t count) { int opts; char work[20]; @@ -2921,15 +2920,14 @@ opts_done: scsi_debug_cmnd_count = 0; return count; } -DRIVER_ATTR(opts, S_IRUGO | S_IWUSR, sdebug_opts_show, - sdebug_opts_store); +static DRIVER_ATTR_RW(opts); -static ssize_t sdebug_ptype_show(struct device_driver * ddp, char * buf) +static ssize_t ptype_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_ptype); } -static ssize_t sdebug_ptype_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t ptype_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -2939,14 +2937,14 @@ static ssize_t sdebug_ptype_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(ptype, S_IRUGO | S_IWUSR, sdebug_ptype_show, sdebug_ptype_store); +static DRIVER_ATTR_RW(ptype); -static ssize_t sdebug_dsense_show(struct device_driver * ddp, char * buf) +static ssize_t dsense_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_dsense); } -static ssize_t sdebug_dsense_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t dsense_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -2956,15 +2954,14 @@ static ssize_t sdebug_dsense_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(dsense, S_IRUGO | S_IWUSR, sdebug_dsense_show, - sdebug_dsense_store); +static DRIVER_ATTR_RW(dsense); -static ssize_t sdebug_fake_rw_show(struct device_driver * ddp, char * buf) +static ssize_t fake_rw_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_fake_rw); } -static ssize_t sdebug_fake_rw_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t fake_rw_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -2974,15 +2971,14 @@ static ssize_t sdebug_fake_rw_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(fake_rw, S_IRUGO | S_IWUSR, sdebug_fake_rw_show, - sdebug_fake_rw_store); +static DRIVER_ATTR_RW(fake_rw); -static ssize_t sdebug_no_lun_0_show(struct device_driver * ddp, char * buf) +static ssize_t no_lun_0_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_no_lun_0); } -static ssize_t sdebug_no_lun_0_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t no_lun_0_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -2992,15 +2988,14 @@ static ssize_t sdebug_no_lun_0_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(no_lun_0, S_IRUGO | S_IWUSR, sdebug_no_lun_0_show, - sdebug_no_lun_0_store); +static DRIVER_ATTR_RW(no_lun_0); -static ssize_t sdebug_num_tgts_show(struct device_driver * ddp, char * buf) +static ssize_t num_tgts_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_num_tgts); } -static ssize_t sdebug_num_tgts_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t num_tgts_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -3011,27 +3006,26 @@ static ssize_t sdebug_num_tgts_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(num_tgts, S_IRUGO | S_IWUSR, sdebug_num_tgts_show, - sdebug_num_tgts_store); +static DRIVER_ATTR_RW(num_tgts); -static ssize_t sdebug_dev_size_mb_show(struct device_driver * ddp, char * buf) +static ssize_t dev_size_mb_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_dev_size_mb); } -DRIVER_ATTR(dev_size_mb, S_IRUGO, sdebug_dev_size_mb_show, NULL); +static DRIVER_ATTR_RO(dev_size_mb); -static ssize_t sdebug_num_parts_show(struct device_driver * ddp, char * buf) +static ssize_t num_parts_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_num_parts); } -DRIVER_ATTR(num_parts, S_IRUGO, sdebug_num_parts_show, NULL); +static DRIVER_ATTR_RO(num_parts); -static ssize_t sdebug_every_nth_show(struct device_driver * ddp, char * buf) +static ssize_t every_nth_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_every_nth); } -static ssize_t sdebug_every_nth_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t every_nth_store(struct device_driver *ddp, const char *buf, + size_t count) { int nth; @@ -3042,15 +3036,14 @@ static ssize_t sdebug_every_nth_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(every_nth, S_IRUGO | S_IWUSR, sdebug_every_nth_show, - sdebug_every_nth_store); +static DRIVER_ATTR_RW(every_nth); -static ssize_t sdebug_max_luns_show(struct device_driver * ddp, char * buf) +static ssize_t max_luns_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_max_luns); } -static ssize_t sdebug_max_luns_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t max_luns_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -3061,15 +3054,14 @@ static ssize_t sdebug_max_luns_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(max_luns, S_IRUGO | S_IWUSR, sdebug_max_luns_show, - sdebug_max_luns_store); +static DRIVER_ATTR_RW(max_luns); -static ssize_t sdebug_max_queue_show(struct device_driver * ddp, char * buf) +static ssize_t max_queue_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_max_queue); } -static ssize_t sdebug_max_queue_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t max_queue_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -3080,27 +3072,26 @@ static ssize_t sdebug_max_queue_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(max_queue, S_IRUGO | S_IWUSR, sdebug_max_queue_show, - sdebug_max_queue_store); +static DRIVER_ATTR_RW(max_queue); -static ssize_t sdebug_no_uld_show(struct device_driver * ddp, char * buf) +static ssize_t no_uld_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_no_uld); } -DRIVER_ATTR(no_uld, S_IRUGO, sdebug_no_uld_show, NULL); +static DRIVER_ATTR_RO(no_uld); -static ssize_t sdebug_scsi_level_show(struct device_driver * ddp, char * buf) +static ssize_t scsi_level_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_scsi_level); } -DRIVER_ATTR(scsi_level, S_IRUGO, sdebug_scsi_level_show, NULL); +static DRIVER_ATTR_RO(scsi_level); -static ssize_t sdebug_virtual_gb_show(struct device_driver * ddp, char * buf) +static ssize_t virtual_gb_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_virtual_gb); } -static ssize_t sdebug_virtual_gb_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t virtual_gb_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -3113,16 +3104,15 @@ static ssize_t sdebug_virtual_gb_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(virtual_gb, S_IRUGO | S_IWUSR, sdebug_virtual_gb_show, - sdebug_virtual_gb_store); +static DRIVER_ATTR_RW(virtual_gb); -static ssize_t sdebug_add_host_show(struct device_driver * ddp, char * buf) +static ssize_t add_host_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_add_host); } -static ssize_t sdebug_add_host_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t add_host_store(struct device_driver *ddp, const char *buf, + size_t count) { int delta_hosts; @@ -3139,16 +3129,14 @@ static ssize_t sdebug_add_host_store(struct device_driver * ddp, } return count; } -DRIVER_ATTR(add_host, S_IRUGO | S_IWUSR, sdebug_add_host_show, - sdebug_add_host_store); +static DRIVER_ATTR_RW(add_host); -static ssize_t sdebug_vpd_use_hostno_show(struct device_driver * ddp, - char * buf) +static ssize_t vpd_use_hostno_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_vpd_use_hostno); } -static ssize_t sdebug_vpd_use_hostno_store(struct device_driver * ddp, - const char * buf, size_t count) +static ssize_t vpd_use_hostno_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -3158,40 +3146,39 @@ static ssize_t sdebug_vpd_use_hostno_store(struct device_driver * ddp, } return -EINVAL; } -DRIVER_ATTR(vpd_use_hostno, S_IRUGO | S_IWUSR, sdebug_vpd_use_hostno_show, - sdebug_vpd_use_hostno_store); +static DRIVER_ATTR_RW(vpd_use_hostno); -static ssize_t sdebug_sector_size_show(struct device_driver * ddp, char * buf) +static ssize_t sector_size_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%u\n", scsi_debug_sector_size); } -DRIVER_ATTR(sector_size, S_IRUGO, sdebug_sector_size_show, NULL); +static DRIVER_ATTR_RO(sector_size); -static ssize_t sdebug_dix_show(struct device_driver *ddp, char *buf) +static ssize_t dix_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_dix); } -DRIVER_ATTR(dix, S_IRUGO, sdebug_dix_show, NULL); +static DRIVER_ATTR_RO(dix); -static ssize_t sdebug_dif_show(struct device_driver *ddp, char *buf) +static ssize_t dif_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_dif); } -DRIVER_ATTR(dif, S_IRUGO, sdebug_dif_show, NULL); +static DRIVER_ATTR_RO(dif); -static ssize_t sdebug_guard_show(struct device_driver *ddp, char *buf) +static ssize_t guard_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%u\n", scsi_debug_guard); } -DRIVER_ATTR(guard, S_IRUGO, sdebug_guard_show, NULL); +static DRIVER_ATTR_RO(guard); -static ssize_t sdebug_ato_show(struct device_driver *ddp, char *buf) +static ssize_t ato_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_ato); } -DRIVER_ATTR(ato, S_IRUGO, sdebug_ato_show, NULL); +static DRIVER_ATTR_RO(ato); -static ssize_t sdebug_map_show(struct device_driver *ddp, char *buf) +static ssize_t map_show(struct device_driver *ddp, char *buf) { ssize_t count; @@ -3206,15 +3193,14 @@ static ssize_t sdebug_map_show(struct device_driver *ddp, char *buf) return count; } -DRIVER_ATTR(map, S_IRUGO, sdebug_map_show, NULL); +static DRIVER_ATTR_RO(map); -static ssize_t sdebug_removable_show(struct device_driver *ddp, - char *buf) +static ssize_t removable_show(struct device_driver *ddp, char *buf) { return scnprintf(buf, PAGE_SIZE, "%d\n", scsi_debug_removable ? 1 : 0); } -static ssize_t sdebug_removable_store(struct device_driver *ddp, - const char *buf, size_t count) +static ssize_t removable_store(struct device_driver *ddp, const char *buf, + size_t count) { int n; @@ -3224,74 +3210,43 @@ static ssize_t sdebug_removable_store(struct device_driver *ddp, } return -EINVAL; } -DRIVER_ATTR(removable, S_IRUGO | S_IWUSR, sdebug_removable_show, - sdebug_removable_store); +static DRIVER_ATTR_RW(removable); - -/* Note: The following function creates attribute files in the +/* Note: The following array creates attribute files in the /sys/bus/pseudo/drivers/scsi_debug directory. The advantage of these files (over those found in the /sys/module/scsi_debug/parameters directory) is that auxiliary actions can be triggered when an attribute is changed. For example see: sdebug_add_host_store() above. */ -static int do_create_driverfs_files(void) -{ - int ret; - ret = driver_create_file(&sdebug_driverfs_driver, &driver_attr_add_host); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_delay); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_dev_size_mb); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_dsense); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_every_nth); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_fake_rw); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_max_luns); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_max_queue); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_no_lun_0); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_no_uld); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_num_parts); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_num_tgts); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_ptype); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_opts); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_removable); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_scsi_level); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_virtual_gb); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_vpd_use_hostno); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_sector_size); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_dix); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_dif); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_guard); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_ato); - ret |= driver_create_file(&sdebug_driverfs_driver, &driver_attr_map); - return ret; -} - -static void do_remove_driverfs_files(void) -{ - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_map); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_ato); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_guard); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_dif); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_dix); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_sector_size); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_vpd_use_hostno); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_virtual_gb); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_scsi_level); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_opts); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_ptype); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_removable); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_num_tgts); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_num_parts); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_no_uld); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_no_lun_0); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_max_queue); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_max_luns); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_fake_rw); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_every_nth); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_dsense); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_dev_size_mb); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_delay); - driver_remove_file(&sdebug_driverfs_driver, &driver_attr_add_host); -} +static struct attribute *sdebug_drv_attrs[] = { + &driver_attr_delay.attr, + &driver_attr_opts.attr, + &driver_attr_ptype.attr, + &driver_attr_dsense.attr, + &driver_attr_fake_rw.attr, + &driver_attr_no_lun_0.attr, + &driver_attr_num_tgts.attr, + &driver_attr_dev_size_mb.attr, + &driver_attr_num_parts.attr, + &driver_attr_every_nth.attr, + &driver_attr_max_luns.attr, + &driver_attr_max_queue.attr, + &driver_attr_no_uld.attr, + &driver_attr_scsi_level.attr, + &driver_attr_virtual_gb.attr, + &driver_attr_add_host.attr, + &driver_attr_vpd_use_hostno.attr, + &driver_attr_sector_size.attr, + &driver_attr_dix.attr, + &driver_attr_dif.attr, + &driver_attr_guard.attr, + &driver_attr_ato.attr, + &driver_attr_map.attr, + &driver_attr_removable.attr, + NULL, +}; +ATTRIBUTE_GROUPS(sdebug_drv); struct device *pseudo_primary; @@ -3456,12 +3411,6 @@ static int __init scsi_debug_init(void) ret); goto bus_unreg; } - ret = do_create_driverfs_files(); - if (ret < 0) { - printk(KERN_WARNING "scsi_debug: driver_create_file error: %d\n", - ret); - goto del_files; - } init_all_queued(); @@ -3482,9 +3431,6 @@ static int __init scsi_debug_init(void) } return 0; -del_files: - do_remove_driverfs_files(); - driver_unregister(&sdebug_driverfs_driver); bus_unreg: bus_unregister(&pseudo_lld_bus); dev_unreg: @@ -3506,7 +3452,6 @@ static void __exit scsi_debug_exit(void) stop_all_queued(); for (; k; k--) sdebug_remove_adapter(); - do_remove_driverfs_files(); driver_unregister(&sdebug_driverfs_driver); bus_unregister(&pseudo_lld_bus); root_device_unregister(pseudo_primary); @@ -4096,4 +4041,5 @@ static struct bus_type pseudo_lld_bus = { .match = pseudo_lld_bus_match, .probe = sdebug_driver_probe, .remove = sdebug_driver_remove, + .drv_groups = sdebug_drv_groups, }; diff --git a/drivers/scsi/scsi_error.c b/drivers/scsi/scsi_error.c index e8bee9f0ad0..78b004da288 100644 --- a/drivers/scsi/scsi_error.c +++ b/drivers/scsi/scsi_error.c @@ -53,6 +53,8 @@ static void scsi_eh_done(struct scsi_cmnd *scmd); #define HOST_RESET_SETTLE_TIME (10) static int scsi_eh_try_stu(struct scsi_cmnd *scmd); +static int scsi_try_to_abort_cmd(struct scsi_host_template *, + struct scsi_cmnd *); /* called with shost->host_lock held */ void scsi_eh_wakeup(struct Scsi_Host *shost) @@ -89,17 +91,138 @@ EXPORT_SYMBOL_GPL(scsi_schedule_eh); static int scsi_host_eh_past_deadline(struct Scsi_Host *shost) { - if (!shost->last_reset || !shost->eh_deadline) + if (!shost->last_reset || shost->eh_deadline == -1) return 0; - if (time_before(jiffies, - shost->last_reset + shost->eh_deadline)) + /* + * 32bit accesses are guaranteed to be atomic + * (on all supported architectures), so instead + * of using a spinlock we can as well double check + * if eh_deadline has been set to 'off' during the + * time_before call. + */ + if (time_before(jiffies, shost->last_reset + shost->eh_deadline) && + shost->eh_deadline > -1) return 0; return 1; } /** + * scmd_eh_abort_handler - Handle command aborts + * @work: command to be aborted. + */ +void +scmd_eh_abort_handler(struct work_struct *work) +{ + struct scsi_cmnd *scmd = + container_of(work, struct scsi_cmnd, abort_work.work); + struct scsi_device *sdev = scmd->device; + int rtn; + + if (scsi_host_eh_past_deadline(sdev->host)) { + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_INFO, scmd, + "scmd %p eh timeout, not aborting\n", + scmd)); + } else { + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_INFO, scmd, + "aborting command %p\n", scmd)); + rtn = scsi_try_to_abort_cmd(sdev->host->hostt, scmd); + if (rtn == SUCCESS) { + scmd->result |= DID_TIME_OUT << 16; + if (scsi_host_eh_past_deadline(sdev->host)) { + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_INFO, scmd, + "scmd %p eh timeout, " + "not retrying aborted " + "command\n", scmd)); + } else if (!scsi_noretry_cmd(scmd) && + (++scmd->retries <= scmd->allowed)) { + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_WARNING, scmd, + "scmd %p retry " + "aborted command\n", scmd)); + scsi_queue_insert(scmd, SCSI_MLQUEUE_EH_RETRY); + return; + } else { + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_WARNING, scmd, + "scmd %p finish " + "aborted command\n", scmd)); + scsi_finish_command(scmd); + return; + } + } else { + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_INFO, scmd, + "scmd %p abort failed, rtn %d\n", + scmd, rtn)); + } + } + + if (!scsi_eh_scmd_add(scmd, 0)) { + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_WARNING, scmd, + "scmd %p terminate " + "aborted command\n", scmd)); + scmd->result |= DID_TIME_OUT << 16; + scsi_finish_command(scmd); + } +} + +/** + * scsi_abort_command - schedule a command abort + * @scmd: scmd to abort. + * + * We only need to abort commands after a command timeout + */ +static int +scsi_abort_command(struct scsi_cmnd *scmd) +{ + struct scsi_device *sdev = scmd->device; + struct Scsi_Host *shost = sdev->host; + unsigned long flags; + + if (scmd->eh_eflags & SCSI_EH_ABORT_SCHEDULED) { + /* + * Retry after abort failed, escalate to next level. + */ + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_INFO, scmd, + "scmd %p previous abort failed\n", scmd)); + cancel_delayed_work(&scmd->abort_work); + return FAILED; + } + + /* + * Do not try a command abort if + * SCSI EH has already started. + */ + spin_lock_irqsave(shost->host_lock, flags); + if (scsi_host_in_recovery(shost)) { + spin_unlock_irqrestore(shost->host_lock, flags); + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_INFO, scmd, + "scmd %p not aborting, host in recovery\n", + scmd)); + return FAILED; + } + + if (shost->eh_deadline != -1 && !shost->last_reset) + shost->last_reset = jiffies; + spin_unlock_irqrestore(shost->host_lock, flags); + + scmd->eh_eflags |= SCSI_EH_ABORT_SCHEDULED; + SCSI_LOG_ERROR_RECOVERY(3, + scmd_printk(KERN_INFO, scmd, + "scmd %p abort scheduled\n", scmd)); + queue_delayed_work(shost->tmf_work_q, &scmd->abort_work, HZ / 100); + return SUCCESS; +} + +/** * scsi_eh_scmd_add - add scsi cmd to error handling. * @scmd: scmd to run eh on. * @eh_flag: optional SCSI_EH flag. @@ -121,10 +244,12 @@ int scsi_eh_scmd_add(struct scsi_cmnd *scmd, int eh_flag) if (scsi_host_set_state(shost, SHOST_CANCEL_RECOVERY)) goto out_unlock; - if (shost->eh_deadline && !shost->last_reset) + if (shost->eh_deadline != -1 && !shost->last_reset) shost->last_reset = jiffies; ret = 1; + if (scmd->eh_eflags & SCSI_EH_ABORT_SCHEDULED) + eh_flag &= ~SCSI_EH_CANCEL_CMD; scmd->eh_eflags |= eh_flag; list_add_tail(&scmd->eh_entry, &shost->eh_cmd_q); shost->host_failed++; @@ -153,7 +278,7 @@ enum blk_eh_timer_return scsi_times_out(struct request *req) trace_scsi_dispatch_cmd_timeout(scmd); scsi_log_completion(scmd, TIMEOUT_ERROR); - if (host->eh_deadline && !host->last_reset) + if (host->eh_deadline != -1 && !host->last_reset) host->last_reset = jiffies; if (host->transportt->eh_timed_out) @@ -161,6 +286,10 @@ enum blk_eh_timer_return scsi_times_out(struct request *req) else if (host->hostt->eh_timed_out) rtn = host->hostt->eh_timed_out(scmd); + if (rtn == BLK_EH_NOT_HANDLED && !host->hostt->no_async_abort) + if (scsi_abort_command(scmd) == SUCCESS) + return BLK_EH_NOT_HANDLED; + scmd->result |= DID_TIME_OUT << 16; if (unlikely(rtn == BLK_EH_NOT_HANDLED && @@ -941,12 +1070,6 @@ retry: scsi_eh_restore_cmnd(scmd, &ses); - if (scmd->request->cmd_type != REQ_TYPE_BLOCK_PC) { - struct scsi_driver *sdrv = scsi_cmd_to_driver(scmd); - if (sdrv->eh_action) - rtn = sdrv->eh_action(scmd, cmnd, cmnd_size, rtn); - } - return rtn; } @@ -964,6 +1087,16 @@ static int scsi_request_sense(struct scsi_cmnd *scmd) return scsi_send_eh_cmnd(scmd, NULL, 0, scmd->device->eh_timeout, ~0); } +static int scsi_eh_action(struct scsi_cmnd *scmd, int rtn) +{ + if (scmd->request->cmd_type != REQ_TYPE_BLOCK_PC) { + struct scsi_driver *sdrv = scsi_cmd_to_driver(scmd); + if (sdrv->eh_action) + rtn = sdrv->eh_action(scmd, rtn); + } + return rtn; +} + /** * scsi_eh_finish_cmd - Handle a cmd that eh is finished with. * @scmd: Original SCSI cmd that eh has finished. @@ -1010,7 +1143,6 @@ int scsi_eh_get_sense(struct list_head *work_q, struct scsi_cmnd *scmd, *next; struct Scsi_Host *shost; int rtn; - unsigned long flags; list_for_each_entry_safe(scmd, next, work_q, eh_entry) { if ((scmd->eh_eflags & SCSI_EH_CANCEL_CMD) || @@ -1018,16 +1150,13 @@ int scsi_eh_get_sense(struct list_head *work_q, continue; shost = scmd->device->host; - spin_lock_irqsave(shost->host_lock, flags); if (scsi_host_eh_past_deadline(shost)) { - spin_unlock_irqrestore(shost->host_lock, flags); SCSI_LOG_ERROR_RECOVERY(3, shost_printk(KERN_INFO, shost, "skip %s, past eh deadline\n", __func__)); break; } - spin_unlock_irqrestore(shost->host_lock, flags); SCSI_LOG_ERROR_RECOVERY(2, scmd_printk(KERN_INFO, scmd, "%s: requesting sense\n", current->comm)); @@ -1113,26 +1242,21 @@ static int scsi_eh_test_devices(struct list_head *cmd_list, struct scsi_cmnd *scmd, *next; struct scsi_device *sdev; int finish_cmds; - unsigned long flags; while (!list_empty(cmd_list)) { scmd = list_entry(cmd_list->next, struct scsi_cmnd, eh_entry); sdev = scmd->device; if (!try_stu) { - spin_lock_irqsave(sdev->host->host_lock, flags); if (scsi_host_eh_past_deadline(sdev->host)) { /* Push items back onto work_q */ list_splice_init(cmd_list, work_q); - spin_unlock_irqrestore(sdev->host->host_lock, - flags); SCSI_LOG_ERROR_RECOVERY(3, shost_printk(KERN_INFO, sdev->host, "skip %s, past eh deadline", __func__)); break; } - spin_unlock_irqrestore(sdev->host->host_lock, flags); } finish_cmds = !scsi_device_online(scmd->device) || @@ -1142,7 +1266,9 @@ static int scsi_eh_test_devices(struct list_head *cmd_list, list_for_each_entry_safe(scmd, next, cmd_list, eh_entry) if (scmd->device == sdev) { - if (finish_cmds) + if (finish_cmds && + (try_stu || + scsi_eh_action(scmd, SUCCESS) == SUCCESS)) scsi_eh_finish_cmd(scmd, done_q); else list_move_tail(&scmd->eh_entry, work_q); @@ -1171,15 +1297,12 @@ static int scsi_eh_abort_cmds(struct list_head *work_q, LIST_HEAD(check_list); int rtn; struct Scsi_Host *shost; - unsigned long flags; list_for_each_entry_safe(scmd, next, work_q, eh_entry) { if (!(scmd->eh_eflags & SCSI_EH_CANCEL_CMD)) continue; shost = scmd->device->host; - spin_lock_irqsave(shost->host_lock, flags); if (scsi_host_eh_past_deadline(shost)) { - spin_unlock_irqrestore(shost->host_lock, flags); list_splice_init(&check_list, work_q); SCSI_LOG_ERROR_RECOVERY(3, shost_printk(KERN_INFO, shost, @@ -1187,7 +1310,6 @@ static int scsi_eh_abort_cmds(struct list_head *work_q, __func__)); return list_empty(work_q); } - spin_unlock_irqrestore(shost->host_lock, flags); SCSI_LOG_ERROR_RECOVERY(3, printk("%s: aborting cmd:" "0x%p\n", current->comm, scmd)); @@ -1251,19 +1373,15 @@ static int scsi_eh_stu(struct Scsi_Host *shost, { struct scsi_cmnd *scmd, *stu_scmd, *next; struct scsi_device *sdev; - unsigned long flags; shost_for_each_device(sdev, shost) { - spin_lock_irqsave(shost->host_lock, flags); if (scsi_host_eh_past_deadline(shost)) { - spin_unlock_irqrestore(shost->host_lock, flags); SCSI_LOG_ERROR_RECOVERY(3, shost_printk(KERN_INFO, shost, "skip %s, past eh deadline\n", __func__)); break; } - spin_unlock_irqrestore(shost->host_lock, flags); stu_scmd = NULL; list_for_each_entry(scmd, work_q, eh_entry) if (scmd->device == sdev && SCSI_SENSE_VALID(scmd) && @@ -1283,7 +1401,8 @@ static int scsi_eh_stu(struct Scsi_Host *shost, !scsi_eh_tur(stu_scmd)) { list_for_each_entry_safe(scmd, next, work_q, eh_entry) { - if (scmd->device == sdev) + if (scmd->device == sdev && + scsi_eh_action(scmd, SUCCESS) == SUCCESS) scsi_eh_finish_cmd(scmd, done_q); } } @@ -1316,20 +1435,16 @@ static int scsi_eh_bus_device_reset(struct Scsi_Host *shost, { struct scsi_cmnd *scmd, *bdr_scmd, *next; struct scsi_device *sdev; - unsigned long flags; int rtn; shost_for_each_device(sdev, shost) { - spin_lock_irqsave(shost->host_lock, flags); if (scsi_host_eh_past_deadline(shost)) { - spin_unlock_irqrestore(shost->host_lock, flags); SCSI_LOG_ERROR_RECOVERY(3, shost_printk(KERN_INFO, shost, "skip %s, past eh deadline\n", __func__)); break; } - spin_unlock_irqrestore(shost->host_lock, flags); bdr_scmd = NULL; list_for_each_entry(scmd, work_q, eh_entry) if (scmd->device == sdev) { @@ -1350,7 +1465,8 @@ static int scsi_eh_bus_device_reset(struct Scsi_Host *shost, !scsi_eh_tur(bdr_scmd)) { list_for_each_entry_safe(scmd, next, work_q, eh_entry) { - if (scmd->device == sdev) + if (scmd->device == sdev && + scsi_eh_action(scmd, rtn) != FAILED) scsi_eh_finish_cmd(scmd, done_q); } @@ -1389,11 +1505,8 @@ static int scsi_eh_target_reset(struct Scsi_Host *shost, struct scsi_cmnd *next, *scmd; int rtn; unsigned int id; - unsigned long flags; - spin_lock_irqsave(shost->host_lock, flags); if (scsi_host_eh_past_deadline(shost)) { - spin_unlock_irqrestore(shost->host_lock, flags); /* push back on work queue for further processing */ list_splice_init(&check_list, work_q); list_splice_init(&tmp_list, work_q); @@ -1403,7 +1516,6 @@ static int scsi_eh_target_reset(struct Scsi_Host *shost, __func__)); return list_empty(work_q); } - spin_unlock_irqrestore(shost->host_lock, flags); scmd = list_entry(tmp_list.next, struct scsi_cmnd, eh_entry); id = scmd_id(scmd); @@ -1448,7 +1560,6 @@ static int scsi_eh_bus_reset(struct Scsi_Host *shost, LIST_HEAD(check_list); unsigned int channel; int rtn; - unsigned long flags; /* * we really want to loop over the various channels, and do this on @@ -1458,9 +1569,7 @@ static int scsi_eh_bus_reset(struct Scsi_Host *shost, */ for (channel = 0; channel <= shost->max_channel; channel++) { - spin_lock_irqsave(shost->host_lock, flags); if (scsi_host_eh_past_deadline(shost)) { - spin_unlock_irqrestore(shost->host_lock, flags); list_splice_init(&check_list, work_q); SCSI_LOG_ERROR_RECOVERY(3, shost_printk(KERN_INFO, shost, @@ -1468,7 +1577,6 @@ static int scsi_eh_bus_reset(struct Scsi_Host *shost, __func__)); return list_empty(work_q); } - spin_unlock_irqrestore(shost->host_lock, flags); chan_scmd = NULL; list_for_each_entry(scmd, work_q, eh_entry) { @@ -1569,7 +1677,7 @@ static void scsi_eh_offline_sdevs(struct list_head *work_q, } /** - * scsi_noretry_cmd - determinte if command should be failed fast + * scsi_noretry_cmd - determine if command should be failed fast * @scmd: SCSI cmd to examine. */ int scsi_noretry_cmd(struct scsi_cmnd *scmd) @@ -1577,6 +1685,8 @@ int scsi_noretry_cmd(struct scsi_cmnd *scmd) switch (host_byte(scmd->result)) { case DID_OK: break; + case DID_TIME_OUT: + goto check_type; case DID_BUS_BUSY: return (scmd->request->cmd_flags & REQ_FAILFAST_TRANSPORT); case DID_PARITY: @@ -1590,18 +1700,19 @@ int scsi_noretry_cmd(struct scsi_cmnd *scmd) return (scmd->request->cmd_flags & REQ_FAILFAST_DRIVER); } - switch (status_byte(scmd->result)) { - case CHECK_CONDITION: - /* - * assume caller has checked sense and determinted - * the check condition was retryable. - */ - if (scmd->request->cmd_flags & REQ_FAILFAST_DEV || - scmd->request->cmd_type == REQ_TYPE_BLOCK_PC) - return 1; - } + if (status_byte(scmd->result) != CHECK_CONDITION) + return 0; - return 0; +check_type: + /* + * assume caller has checked sense and determined + * the check condition was retryable. + */ + if (scmd->request->cmd_flags & REQ_FAILFAST_DEV || + scmd->request->cmd_type == REQ_TYPE_BLOCK_PC) + return 1; + else + return 0; } /** @@ -1651,9 +1762,13 @@ int scsi_decide_disposition(struct scsi_cmnd *scmd) * looks good. drop through, and check the next byte. */ break; + case DID_ABORT: + if (scmd->eh_eflags & SCSI_EH_ABORT_SCHEDULED) { + scmd->result |= DID_TIME_OUT << 16; + return SUCCESS; + } case DID_NO_CONNECT: case DID_BAD_TARGET: - case DID_ABORT: /* * note - this means that we just report the status back * to the top level driver, not that we actually think @@ -1999,7 +2114,7 @@ static void scsi_unjam_host(struct Scsi_Host *shost) scsi_eh_ready_devs(shost, &eh_work_q, &eh_done_q); spin_lock_irqsave(shost->host_lock, flags); - if (shost->eh_deadline) + if (shost->eh_deadline != -1) shost->last_reset = 0; spin_unlock_irqrestore(shost->host_lock, flags); scsi_eh_flush_done_q(&eh_done_q); diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c index 7bd7f0d5f05..62ec84b42e3 100644 --- a/drivers/scsi/scsi_lib.c +++ b/drivers/scsi/scsi_lib.c @@ -1684,7 +1684,7 @@ u64 scsi_calculate_bounce_limit(struct Scsi_Host *shost) host_dev = scsi_get_device(shost); if (host_dev && host_dev->dma_mask) - bounce_limit = dma_max_pfn(host_dev) << PAGE_SHIFT; + bounce_limit = (u64)dma_max_pfn(host_dev) << PAGE_SHIFT; return bounce_limit; } diff --git a/drivers/scsi/scsi_pm.c b/drivers/scsi/scsi_pm.c index af4c050ce6e..001e9ceda4c 100644 --- a/drivers/scsi/scsi_pm.c +++ b/drivers/scsi/scsi_pm.c @@ -16,6 +16,8 @@ #include "scsi_priv.h" +#ifdef CONFIG_PM_SLEEP + static int scsi_dev_type_suspend(struct device *dev, int (*cb)(struct device *)) { int err; @@ -43,8 +45,6 @@ static int scsi_dev_type_resume(struct device *dev, int (*cb)(struct device *)) return err; } -#ifdef CONFIG_PM_SLEEP - static int scsi_bus_suspend_common(struct device *dev, int (*cb)(struct device *)) { @@ -145,38 +145,22 @@ static int scsi_bus_restore(struct device *dev) #ifdef CONFIG_PM_RUNTIME -static int sdev_blk_runtime_suspend(struct scsi_device *sdev, - int (*cb)(struct device *)) +static int sdev_runtime_suspend(struct device *dev) { + const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL; + struct scsi_device *sdev = to_scsi_device(dev); int err; err = blk_pre_runtime_suspend(sdev->request_queue); if (err) return err; - if (cb) - err = cb(&sdev->sdev_gendev); + if (pm && pm->runtime_suspend) + err = pm->runtime_suspend(dev); blk_post_runtime_suspend(sdev->request_queue, err); return err; } -static int sdev_runtime_suspend(struct device *dev) -{ - const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL; - int (*cb)(struct device *) = pm ? pm->runtime_suspend : NULL; - struct scsi_device *sdev = to_scsi_device(dev); - int err; - - if (sdev->request_queue->dev) - return sdev_blk_runtime_suspend(sdev, cb); - - err = scsi_dev_type_suspend(dev, cb); - if (err == -EAGAIN) - pm_schedule_suspend(dev, jiffies_to_msecs( - round_jiffies_up_relative(HZ/10))); - return err; -} - static int scsi_runtime_suspend(struct device *dev) { int err = 0; @@ -190,31 +174,20 @@ static int scsi_runtime_suspend(struct device *dev) return err; } -static int sdev_blk_runtime_resume(struct scsi_device *sdev, - int (*cb)(struct device *)) +static int sdev_runtime_resume(struct device *dev) { + struct scsi_device *sdev = to_scsi_device(dev); + const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL; int err = 0; blk_pre_runtime_resume(sdev->request_queue); - if (cb) - err = cb(&sdev->sdev_gendev); + if (pm && pm->runtime_resume) + err = pm->runtime_resume(dev); blk_post_runtime_resume(sdev->request_queue, err); return err; } -static int sdev_runtime_resume(struct device *dev) -{ - struct scsi_device *sdev = to_scsi_device(dev); - const struct dev_pm_ops *pm = dev->driver ? dev->driver->pm : NULL; - int (*cb)(struct device *) = pm ? pm->runtime_resume : NULL; - - if (sdev->request_queue->dev) - return sdev_blk_runtime_resume(sdev, cb); - else - return scsi_dev_type_resume(dev, cb); -} - static int scsi_runtime_resume(struct device *dev) { int err = 0; @@ -235,14 +208,11 @@ static int scsi_runtime_idle(struct device *dev) /* Insert hooks here for targets, hosts, and transport classes */ if (scsi_is_sdev_device(dev)) { - struct scsi_device *sdev = to_scsi_device(dev); - - if (sdev->request_queue->dev) { - pm_runtime_mark_last_busy(dev); - pm_runtime_autosuspend(dev); - return -EBUSY; - } + pm_runtime_mark_last_busy(dev); + pm_runtime_autosuspend(dev); + return -EBUSY; } + return 0; } diff --git a/drivers/scsi/scsi_priv.h b/drivers/scsi/scsi_priv.h index 8f9a0cadc29..f079a598bed 100644 --- a/drivers/scsi/scsi_priv.h +++ b/drivers/scsi/scsi_priv.h @@ -19,6 +19,7 @@ struct scsi_nl_hdr; * Scsi Error Handler Flags */ #define SCSI_EH_CANCEL_CMD 0x0001 /* Cancel this cmd */ +#define SCSI_EH_ABORT_SCHEDULED 0x0002 /* Abort has been scheduled */ #define SCSI_SENSE_VALID(scmd) \ (((scmd)->sense_buffer[0] & 0x70) == 0x70) @@ -66,6 +67,7 @@ extern int __init scsi_init_devinfo(void); extern void scsi_exit_devinfo(void); /* scsi_error.c */ +extern void scmd_eh_abort_handler(struct work_struct *work); extern enum blk_eh_timer_return scsi_times_out(struct request *req); extern int scsi_error_handler(void *host); extern int scsi_decide_disposition(struct scsi_cmnd *cmd); diff --git a/drivers/scsi/scsi_sysfs.c b/drivers/scsi/scsi_sysfs.c index 8ff62c26a41..9117d0bf408 100644 --- a/drivers/scsi/scsi_sysfs.c +++ b/drivers/scsi/scsi_sysfs.c @@ -287,7 +287,9 @@ show_shost_eh_deadline(struct device *dev, { struct Scsi_Host *shost = class_to_shost(dev); - return sprintf(buf, "%d\n", shost->eh_deadline / HZ); + if (shost->eh_deadline == -1) + return snprintf(buf, strlen("off") + 2, "off\n"); + return sprintf(buf, "%u\n", shost->eh_deadline / HZ); } static ssize_t @@ -296,22 +298,34 @@ store_shost_eh_deadline(struct device *dev, struct device_attribute *attr, { struct Scsi_Host *shost = class_to_shost(dev); int ret = -EINVAL; - int deadline; - unsigned long flags; + unsigned long deadline, flags; if (shost->transportt && shost->transportt->eh_strategy_handler) return ret; - if (sscanf(buf, "%d\n", &deadline) == 1) { - spin_lock_irqsave(shost->host_lock, flags); - if (scsi_host_in_recovery(shost)) - ret = -EBUSY; - else { + if (!strncmp(buf, "off", strlen("off"))) + deadline = -1; + else { + ret = kstrtoul(buf, 10, &deadline); + if (ret) + return ret; + if (deadline * HZ > UINT_MAX) + return -EINVAL; + } + + spin_lock_irqsave(shost->host_lock, flags); + if (scsi_host_in_recovery(shost)) + ret = -EBUSY; + else { + if (deadline == -1) + shost->eh_deadline = -1; + else shost->eh_deadline = deadline * HZ; - ret = count; - } - spin_unlock_irqrestore(shost->host_lock, flags); + + ret = count; } + spin_unlock_irqrestore(shost->host_lock, flags); + return ret; } diff --git a/drivers/scsi/scsi_transport_iscsi.c b/drivers/scsi/scsi_transport_iscsi.c index 63a6ca49d4e..fd8ffe6bcfd 100644 --- a/drivers/scsi/scsi_transport_iscsi.c +++ b/drivers/scsi/scsi_transport_iscsi.c @@ -305,20 +305,71 @@ show_##type##_##name(struct device *dev, struct device_attribute *attr, \ iscsi_iface_attr_show(type, name, ISCSI_NET_PARAM, param) \ static ISCSI_IFACE_ATTR(type, name, S_IRUGO, show_##type##_##name, NULL); -/* generic read only ipvi4 attribute */ +#define iscsi_iface_attr(type, name, param) \ + iscsi_iface_attr_show(type, name, ISCSI_IFACE_PARAM, param) \ +static ISCSI_IFACE_ATTR(type, name, S_IRUGO, show_##type##_##name, NULL); + +/* generic read only ipv4 attribute */ iscsi_iface_net_attr(ipv4_iface, ipaddress, ISCSI_NET_PARAM_IPV4_ADDR); iscsi_iface_net_attr(ipv4_iface, gateway, ISCSI_NET_PARAM_IPV4_GW); iscsi_iface_net_attr(ipv4_iface, subnet, ISCSI_NET_PARAM_IPV4_SUBNET); iscsi_iface_net_attr(ipv4_iface, bootproto, ISCSI_NET_PARAM_IPV4_BOOTPROTO); +iscsi_iface_net_attr(ipv4_iface, dhcp_dns_address_en, + ISCSI_NET_PARAM_IPV4_DHCP_DNS_ADDR_EN); +iscsi_iface_net_attr(ipv4_iface, dhcp_slp_da_info_en, + ISCSI_NET_PARAM_IPV4_DHCP_SLP_DA_EN); +iscsi_iface_net_attr(ipv4_iface, tos_en, ISCSI_NET_PARAM_IPV4_TOS_EN); +iscsi_iface_net_attr(ipv4_iface, tos, ISCSI_NET_PARAM_IPV4_TOS); +iscsi_iface_net_attr(ipv4_iface, grat_arp_en, + ISCSI_NET_PARAM_IPV4_GRAT_ARP_EN); +iscsi_iface_net_attr(ipv4_iface, dhcp_alt_client_id_en, + ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID_EN); +iscsi_iface_net_attr(ipv4_iface, dhcp_alt_client_id, + ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID); +iscsi_iface_net_attr(ipv4_iface, dhcp_req_vendor_id_en, + ISCSI_NET_PARAM_IPV4_DHCP_REQ_VENDOR_ID_EN); +iscsi_iface_net_attr(ipv4_iface, dhcp_use_vendor_id_en, + ISCSI_NET_PARAM_IPV4_DHCP_USE_VENDOR_ID_EN); +iscsi_iface_net_attr(ipv4_iface, dhcp_vendor_id, + ISCSI_NET_PARAM_IPV4_DHCP_VENDOR_ID); +iscsi_iface_net_attr(ipv4_iface, dhcp_learn_iqn_en, + ISCSI_NET_PARAM_IPV4_DHCP_LEARN_IQN_EN); +iscsi_iface_net_attr(ipv4_iface, fragment_disable, + ISCSI_NET_PARAM_IPV4_FRAGMENT_DISABLE); +iscsi_iface_net_attr(ipv4_iface, incoming_forwarding_en, + ISCSI_NET_PARAM_IPV4_IN_FORWARD_EN); +iscsi_iface_net_attr(ipv4_iface, ttl, ISCSI_NET_PARAM_IPV4_TTL); /* generic read only ipv6 attribute */ iscsi_iface_net_attr(ipv6_iface, ipaddress, ISCSI_NET_PARAM_IPV6_ADDR); -iscsi_iface_net_attr(ipv6_iface, link_local_addr, ISCSI_NET_PARAM_IPV6_LINKLOCAL); +iscsi_iface_net_attr(ipv6_iface, link_local_addr, + ISCSI_NET_PARAM_IPV6_LINKLOCAL); iscsi_iface_net_attr(ipv6_iface, router_addr, ISCSI_NET_PARAM_IPV6_ROUTER); iscsi_iface_net_attr(ipv6_iface, ipaddr_autocfg, ISCSI_NET_PARAM_IPV6_ADDR_AUTOCFG); iscsi_iface_net_attr(ipv6_iface, link_local_autocfg, ISCSI_NET_PARAM_IPV6_LINKLOCAL_AUTOCFG); +iscsi_iface_net_attr(ipv6_iface, link_local_state, + ISCSI_NET_PARAM_IPV6_LINKLOCAL_STATE); +iscsi_iface_net_attr(ipv6_iface, router_state, + ISCSI_NET_PARAM_IPV6_ROUTER_STATE); +iscsi_iface_net_attr(ipv6_iface, grat_neighbor_adv_en, + ISCSI_NET_PARAM_IPV6_GRAT_NEIGHBOR_ADV_EN); +iscsi_iface_net_attr(ipv6_iface, mld_en, ISCSI_NET_PARAM_IPV6_MLD_EN); +iscsi_iface_net_attr(ipv6_iface, flow_label, ISCSI_NET_PARAM_IPV6_FLOW_LABEL); +iscsi_iface_net_attr(ipv6_iface, traffic_class, + ISCSI_NET_PARAM_IPV6_TRAFFIC_CLASS); +iscsi_iface_net_attr(ipv6_iface, hop_limit, ISCSI_NET_PARAM_IPV6_HOP_LIMIT); +iscsi_iface_net_attr(ipv6_iface, nd_reachable_tmo, + ISCSI_NET_PARAM_IPV6_ND_REACHABLE_TMO); +iscsi_iface_net_attr(ipv6_iface, nd_rexmit_time, + ISCSI_NET_PARAM_IPV6_ND_REXMIT_TIME); +iscsi_iface_net_attr(ipv6_iface, nd_stale_tmo, + ISCSI_NET_PARAM_IPV6_ND_STALE_TMO); +iscsi_iface_net_attr(ipv6_iface, dup_addr_detect_cnt, + ISCSI_NET_PARAM_IPV6_DUP_ADDR_DETECT_CNT); +iscsi_iface_net_attr(ipv6_iface, router_adv_link_mtu, + ISCSI_NET_PARAM_IPV6_RTR_ADV_LINK_MTU); /* common read only iface attribute */ iscsi_iface_net_attr(iface, enabled, ISCSI_NET_PARAM_IFACE_ENABLE); @@ -327,6 +378,40 @@ iscsi_iface_net_attr(iface, vlan_priority, ISCSI_NET_PARAM_VLAN_PRIORITY); iscsi_iface_net_attr(iface, vlan_enabled, ISCSI_NET_PARAM_VLAN_ENABLED); iscsi_iface_net_attr(iface, mtu, ISCSI_NET_PARAM_MTU); iscsi_iface_net_attr(iface, port, ISCSI_NET_PARAM_PORT); +iscsi_iface_net_attr(iface, ipaddress_state, ISCSI_NET_PARAM_IPADDR_STATE); +iscsi_iface_net_attr(iface, delayed_ack_en, ISCSI_NET_PARAM_DELAYED_ACK_EN); +iscsi_iface_net_attr(iface, tcp_nagle_disable, + ISCSI_NET_PARAM_TCP_NAGLE_DISABLE); +iscsi_iface_net_attr(iface, tcp_wsf_disable, ISCSI_NET_PARAM_TCP_WSF_DISABLE); +iscsi_iface_net_attr(iface, tcp_wsf, ISCSI_NET_PARAM_TCP_WSF); +iscsi_iface_net_attr(iface, tcp_timer_scale, ISCSI_NET_PARAM_TCP_TIMER_SCALE); +iscsi_iface_net_attr(iface, tcp_timestamp_en, ISCSI_NET_PARAM_TCP_TIMESTAMP_EN); +iscsi_iface_net_attr(iface, cache_id, ISCSI_NET_PARAM_CACHE_ID); +iscsi_iface_net_attr(iface, redirect_en, ISCSI_NET_PARAM_REDIRECT_EN); + +/* common iscsi specific settings attributes */ +iscsi_iface_attr(iface, def_taskmgmt_tmo, ISCSI_IFACE_PARAM_DEF_TASKMGMT_TMO); +iscsi_iface_attr(iface, header_digest, ISCSI_IFACE_PARAM_HDRDGST_EN); +iscsi_iface_attr(iface, data_digest, ISCSI_IFACE_PARAM_DATADGST_EN); +iscsi_iface_attr(iface, immediate_data, ISCSI_IFACE_PARAM_IMM_DATA_EN); +iscsi_iface_attr(iface, initial_r2t, ISCSI_IFACE_PARAM_INITIAL_R2T_EN); +iscsi_iface_attr(iface, data_seq_in_order, + ISCSI_IFACE_PARAM_DATASEQ_INORDER_EN); +iscsi_iface_attr(iface, data_pdu_in_order, ISCSI_IFACE_PARAM_PDU_INORDER_EN); +iscsi_iface_attr(iface, erl, ISCSI_IFACE_PARAM_ERL); +iscsi_iface_attr(iface, max_recv_dlength, ISCSI_IFACE_PARAM_MAX_RECV_DLENGTH); +iscsi_iface_attr(iface, first_burst_len, ISCSI_IFACE_PARAM_FIRST_BURST); +iscsi_iface_attr(iface, max_outstanding_r2t, ISCSI_IFACE_PARAM_MAX_R2T); +iscsi_iface_attr(iface, max_burst_len, ISCSI_IFACE_PARAM_MAX_BURST); +iscsi_iface_attr(iface, chap_auth, ISCSI_IFACE_PARAM_CHAP_AUTH_EN); +iscsi_iface_attr(iface, bidi_chap, ISCSI_IFACE_PARAM_BIDI_CHAP_EN); +iscsi_iface_attr(iface, discovery_auth_optional, + ISCSI_IFACE_PARAM_DISCOVERY_AUTH_OPTIONAL); +iscsi_iface_attr(iface, discovery_logout, + ISCSI_IFACE_PARAM_DISCOVERY_LOGOUT_EN); +iscsi_iface_attr(iface, strict_login_comp_en, + ISCSI_IFACE_PARAM_STRICT_LOGIN_COMP_EN); +iscsi_iface_attr(iface, initiator_name, ISCSI_IFACE_PARAM_INITIATOR_NAME); static umode_t iscsi_iface_attr_is_visible(struct kobject *kobj, struct attribute *attr, int i) @@ -335,6 +420,7 @@ static umode_t iscsi_iface_attr_is_visible(struct kobject *kobj, struct iscsi_iface *iface = iscsi_dev_to_iface(dev); struct iscsi_transport *t = iface->transport; int param; + int param_type; if (attr == &dev_attr_iface_enabled.attr) param = ISCSI_NET_PARAM_IFACE_ENABLE; @@ -348,6 +434,60 @@ static umode_t iscsi_iface_attr_is_visible(struct kobject *kobj, param = ISCSI_NET_PARAM_MTU; else if (attr == &dev_attr_iface_port.attr) param = ISCSI_NET_PARAM_PORT; + else if (attr == &dev_attr_iface_ipaddress_state.attr) + param = ISCSI_NET_PARAM_IPADDR_STATE; + else if (attr == &dev_attr_iface_delayed_ack_en.attr) + param = ISCSI_NET_PARAM_DELAYED_ACK_EN; + else if (attr == &dev_attr_iface_tcp_nagle_disable.attr) + param = ISCSI_NET_PARAM_TCP_NAGLE_DISABLE; + else if (attr == &dev_attr_iface_tcp_wsf_disable.attr) + param = ISCSI_NET_PARAM_TCP_WSF_DISABLE; + else if (attr == &dev_attr_iface_tcp_wsf.attr) + param = ISCSI_NET_PARAM_TCP_WSF; + else if (attr == &dev_attr_iface_tcp_timer_scale.attr) + param = ISCSI_NET_PARAM_TCP_TIMER_SCALE; + else if (attr == &dev_attr_iface_tcp_timestamp_en.attr) + param = ISCSI_NET_PARAM_TCP_TIMESTAMP_EN; + else if (attr == &dev_attr_iface_cache_id.attr) + param = ISCSI_NET_PARAM_CACHE_ID; + else if (attr == &dev_attr_iface_redirect_en.attr) + param = ISCSI_NET_PARAM_REDIRECT_EN; + else if (attr == &dev_attr_iface_def_taskmgmt_tmo.attr) + param = ISCSI_IFACE_PARAM_DEF_TASKMGMT_TMO; + else if (attr == &dev_attr_iface_header_digest.attr) + param = ISCSI_IFACE_PARAM_HDRDGST_EN; + else if (attr == &dev_attr_iface_data_digest.attr) + param = ISCSI_IFACE_PARAM_DATADGST_EN; + else if (attr == &dev_attr_iface_immediate_data.attr) + param = ISCSI_IFACE_PARAM_IMM_DATA_EN; + else if (attr == &dev_attr_iface_initial_r2t.attr) + param = ISCSI_IFACE_PARAM_INITIAL_R2T_EN; + else if (attr == &dev_attr_iface_data_seq_in_order.attr) + param = ISCSI_IFACE_PARAM_DATASEQ_INORDER_EN; + else if (attr == &dev_attr_iface_data_pdu_in_order.attr) + param = ISCSI_IFACE_PARAM_PDU_INORDER_EN; + else if (attr == &dev_attr_iface_erl.attr) + param = ISCSI_IFACE_PARAM_ERL; + else if (attr == &dev_attr_iface_max_recv_dlength.attr) + param = ISCSI_IFACE_PARAM_MAX_RECV_DLENGTH; + else if (attr == &dev_attr_iface_first_burst_len.attr) + param = ISCSI_IFACE_PARAM_FIRST_BURST; + else if (attr == &dev_attr_iface_max_outstanding_r2t.attr) + param = ISCSI_IFACE_PARAM_MAX_R2T; + else if (attr == &dev_attr_iface_max_burst_len.attr) + param = ISCSI_IFACE_PARAM_MAX_BURST; + else if (attr == &dev_attr_iface_chap_auth.attr) + param = ISCSI_IFACE_PARAM_CHAP_AUTH_EN; + else if (attr == &dev_attr_iface_bidi_chap.attr) + param = ISCSI_IFACE_PARAM_BIDI_CHAP_EN; + else if (attr == &dev_attr_iface_discovery_auth_optional.attr) + param = ISCSI_IFACE_PARAM_DISCOVERY_AUTH_OPTIONAL; + else if (attr == &dev_attr_iface_discovery_logout.attr) + param = ISCSI_IFACE_PARAM_DISCOVERY_LOGOUT_EN; + else if (attr == &dev_attr_iface_strict_login_comp_en.attr) + param = ISCSI_IFACE_PARAM_STRICT_LOGIN_COMP_EN; + else if (attr == &dev_attr_iface_initiator_name.attr) + param = ISCSI_IFACE_PARAM_INITIATOR_NAME; else if (iface->iface_type == ISCSI_IFACE_TYPE_IPV4) { if (attr == &dev_attr_ipv4_iface_ipaddress.attr) param = ISCSI_NET_PARAM_IPV4_ADDR; @@ -357,6 +497,42 @@ static umode_t iscsi_iface_attr_is_visible(struct kobject *kobj, param = ISCSI_NET_PARAM_IPV4_SUBNET; else if (attr == &dev_attr_ipv4_iface_bootproto.attr) param = ISCSI_NET_PARAM_IPV4_BOOTPROTO; + else if (attr == + &dev_attr_ipv4_iface_dhcp_dns_address_en.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_DNS_ADDR_EN; + else if (attr == + &dev_attr_ipv4_iface_dhcp_slp_da_info_en.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_SLP_DA_EN; + else if (attr == &dev_attr_ipv4_iface_tos_en.attr) + param = ISCSI_NET_PARAM_IPV4_TOS_EN; + else if (attr == &dev_attr_ipv4_iface_tos.attr) + param = ISCSI_NET_PARAM_IPV4_TOS; + else if (attr == &dev_attr_ipv4_iface_grat_arp_en.attr) + param = ISCSI_NET_PARAM_IPV4_GRAT_ARP_EN; + else if (attr == + &dev_attr_ipv4_iface_dhcp_alt_client_id_en.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID_EN; + else if (attr == &dev_attr_ipv4_iface_dhcp_alt_client_id.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_ALT_CLIENT_ID; + else if (attr == + &dev_attr_ipv4_iface_dhcp_req_vendor_id_en.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_REQ_VENDOR_ID_EN; + else if (attr == + &dev_attr_ipv4_iface_dhcp_use_vendor_id_en.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_USE_VENDOR_ID_EN; + else if (attr == &dev_attr_ipv4_iface_dhcp_vendor_id.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_VENDOR_ID; + else if (attr == + &dev_attr_ipv4_iface_dhcp_learn_iqn_en.attr) + param = ISCSI_NET_PARAM_IPV4_DHCP_LEARN_IQN_EN; + else if (attr == + &dev_attr_ipv4_iface_fragment_disable.attr) + param = ISCSI_NET_PARAM_IPV4_FRAGMENT_DISABLE; + else if (attr == + &dev_attr_ipv4_iface_incoming_forwarding_en.attr) + param = ISCSI_NET_PARAM_IPV4_IN_FORWARD_EN; + else if (attr == &dev_attr_ipv4_iface_ttl.attr) + param = ISCSI_NET_PARAM_IPV4_TTL; else return 0; } else if (iface->iface_type == ISCSI_IFACE_TYPE_IPV6) { @@ -370,6 +546,31 @@ static umode_t iscsi_iface_attr_is_visible(struct kobject *kobj, param = ISCSI_NET_PARAM_IPV6_ADDR_AUTOCFG; else if (attr == &dev_attr_ipv6_iface_link_local_autocfg.attr) param = ISCSI_NET_PARAM_IPV6_LINKLOCAL_AUTOCFG; + else if (attr == &dev_attr_ipv6_iface_link_local_state.attr) + param = ISCSI_NET_PARAM_IPV6_LINKLOCAL_STATE; + else if (attr == &dev_attr_ipv6_iface_router_state.attr) + param = ISCSI_NET_PARAM_IPV6_ROUTER_STATE; + else if (attr == + &dev_attr_ipv6_iface_grat_neighbor_adv_en.attr) + param = ISCSI_NET_PARAM_IPV6_GRAT_NEIGHBOR_ADV_EN; + else if (attr == &dev_attr_ipv6_iface_mld_en.attr) + param = ISCSI_NET_PARAM_IPV6_MLD_EN; + else if (attr == &dev_attr_ipv6_iface_flow_label.attr) + param = ISCSI_NET_PARAM_IPV6_FLOW_LABEL; + else if (attr == &dev_attr_ipv6_iface_traffic_class.attr) + param = ISCSI_NET_PARAM_IPV6_TRAFFIC_CLASS; + else if (attr == &dev_attr_ipv6_iface_hop_limit.attr) + param = ISCSI_NET_PARAM_IPV6_HOP_LIMIT; + else if (attr == &dev_attr_ipv6_iface_nd_reachable_tmo.attr) + param = ISCSI_NET_PARAM_IPV6_ND_REACHABLE_TMO; + else if (attr == &dev_attr_ipv6_iface_nd_rexmit_time.attr) + param = ISCSI_NET_PARAM_IPV6_ND_REXMIT_TIME; + else if (attr == &dev_attr_ipv6_iface_nd_stale_tmo.attr) + param = ISCSI_NET_PARAM_IPV6_ND_STALE_TMO; + else if (attr == &dev_attr_ipv6_iface_dup_addr_detect_cnt.attr) + param = ISCSI_NET_PARAM_IPV6_DUP_ADDR_DETECT_CNT; + else if (attr == &dev_attr_ipv6_iface_router_adv_link_mtu.attr) + param = ISCSI_NET_PARAM_IPV6_RTR_ADV_LINK_MTU; else return 0; } else { @@ -377,7 +578,32 @@ static umode_t iscsi_iface_attr_is_visible(struct kobject *kobj, return 0; } - return t->attr_is_visible(ISCSI_NET_PARAM, param); + switch (param) { + case ISCSI_IFACE_PARAM_DEF_TASKMGMT_TMO: + case ISCSI_IFACE_PARAM_HDRDGST_EN: + case ISCSI_IFACE_PARAM_DATADGST_EN: + case ISCSI_IFACE_PARAM_IMM_DATA_EN: + case ISCSI_IFACE_PARAM_INITIAL_R2T_EN: + case ISCSI_IFACE_PARAM_DATASEQ_INORDER_EN: + case ISCSI_IFACE_PARAM_PDU_INORDER_EN: + case ISCSI_IFACE_PARAM_ERL: + case ISCSI_IFACE_PARAM_MAX_RECV_DLENGTH: + case ISCSI_IFACE_PARAM_FIRST_BURST: + case ISCSI_IFACE_PARAM_MAX_R2T: + case ISCSI_IFACE_PARAM_MAX_BURST: + case ISCSI_IFACE_PARAM_CHAP_AUTH_EN: + case ISCSI_IFACE_PARAM_BIDI_CHAP_EN: + case ISCSI_IFACE_PARAM_DISCOVERY_AUTH_OPTIONAL: + case ISCSI_IFACE_PARAM_DISCOVERY_LOGOUT_EN: + case ISCSI_IFACE_PARAM_STRICT_LOGIN_COMP_EN: + case ISCSI_IFACE_PARAM_INITIATOR_NAME: + param_type = ISCSI_IFACE_PARAM; + break; + default: + param_type = ISCSI_NET_PARAM; + } + + return t->attr_is_visible(param_type, param); } static struct attribute *iscsi_iface_attrs[] = { @@ -396,6 +622,59 @@ static struct attribute *iscsi_iface_attrs[] = { &dev_attr_ipv6_iface_link_local_autocfg.attr, &dev_attr_iface_mtu.attr, &dev_attr_iface_port.attr, + &dev_attr_iface_ipaddress_state.attr, + &dev_attr_iface_delayed_ack_en.attr, + &dev_attr_iface_tcp_nagle_disable.attr, + &dev_attr_iface_tcp_wsf_disable.attr, + &dev_attr_iface_tcp_wsf.attr, + &dev_attr_iface_tcp_timer_scale.attr, + &dev_attr_iface_tcp_timestamp_en.attr, + &dev_attr_iface_cache_id.attr, + &dev_attr_iface_redirect_en.attr, + &dev_attr_iface_def_taskmgmt_tmo.attr, + &dev_attr_iface_header_digest.attr, + &dev_attr_iface_data_digest.attr, + &dev_attr_iface_immediate_data.attr, + &dev_attr_iface_initial_r2t.attr, + &dev_attr_iface_data_seq_in_order.attr, + &dev_attr_iface_data_pdu_in_order.attr, + &dev_attr_iface_erl.attr, + &dev_attr_iface_max_recv_dlength.attr, + &dev_attr_iface_first_burst_len.attr, + &dev_attr_iface_max_outstanding_r2t.attr, + &dev_attr_iface_max_burst_len.attr, + &dev_attr_iface_chap_auth.attr, + &dev_attr_iface_bidi_chap.attr, + &dev_attr_iface_discovery_auth_optional.attr, + &dev_attr_iface_discovery_logout.attr, + &dev_attr_iface_strict_login_comp_en.attr, + &dev_attr_iface_initiator_name.attr, + &dev_attr_ipv4_iface_dhcp_dns_address_en.attr, + &dev_attr_ipv4_iface_dhcp_slp_da_info_en.attr, + &dev_attr_ipv4_iface_tos_en.attr, + &dev_attr_ipv4_iface_tos.attr, + &dev_attr_ipv4_iface_grat_arp_en.attr, + &dev_attr_ipv4_iface_dhcp_alt_client_id_en.attr, + &dev_attr_ipv4_iface_dhcp_alt_client_id.attr, + &dev_attr_ipv4_iface_dhcp_req_vendor_id_en.attr, + &dev_attr_ipv4_iface_dhcp_use_vendor_id_en.attr, + &dev_attr_ipv4_iface_dhcp_vendor_id.attr, + &dev_attr_ipv4_iface_dhcp_learn_iqn_en.attr, + &dev_attr_ipv4_iface_fragment_disable.attr, + &dev_attr_ipv4_iface_incoming_forwarding_en.attr, + &dev_attr_ipv4_iface_ttl.attr, + &dev_attr_ipv6_iface_link_local_state.attr, + &dev_attr_ipv6_iface_router_state.attr, + &dev_attr_ipv6_iface_grat_neighbor_adv_en.attr, + &dev_attr_ipv6_iface_mld_en.attr, + &dev_attr_ipv6_iface_flow_label.attr, + &dev_attr_ipv6_iface_traffic_class.attr, + &dev_attr_ipv6_iface_hop_limit.attr, + &dev_attr_ipv6_iface_nd_reachable_tmo.attr, + &dev_attr_ipv6_iface_nd_rexmit_time.attr, + &dev_attr_ipv6_iface_nd_stale_tmo.attr, + &dev_attr_ipv6_iface_dup_addr_detect_cnt.attr, + &dev_attr_ipv6_iface_router_adv_link_mtu.attr, NULL, }; @@ -404,6 +683,61 @@ static struct attribute_group iscsi_iface_group = { .is_visible = iscsi_iface_attr_is_visible, }; +/* convert iscsi_ipaddress_state values to ascii string name */ +static const struct { + enum iscsi_ipaddress_state value; + char *name; +} iscsi_ipaddress_state_names[] = { + {ISCSI_IPDDRESS_STATE_UNCONFIGURED, "Unconfigured" }, + {ISCSI_IPDDRESS_STATE_ACQUIRING, "Acquiring" }, + {ISCSI_IPDDRESS_STATE_TENTATIVE, "Tentative" }, + {ISCSI_IPDDRESS_STATE_VALID, "Valid" }, + {ISCSI_IPDDRESS_STATE_DISABLING, "Disabling" }, + {ISCSI_IPDDRESS_STATE_INVALID, "Invalid" }, + {ISCSI_IPDDRESS_STATE_DEPRECATED, "Deprecated" }, +}; + +char *iscsi_get_ipaddress_state_name(enum iscsi_ipaddress_state port_state) +{ + int i; + char *state = NULL; + + for (i = 0; i < ARRAY_SIZE(iscsi_ipaddress_state_names); i++) { + if (iscsi_ipaddress_state_names[i].value == port_state) { + state = iscsi_ipaddress_state_names[i].name; + break; + } + } + return state; +} +EXPORT_SYMBOL_GPL(iscsi_get_ipaddress_state_name); + +/* convert iscsi_router_state values to ascii string name */ +static const struct { + enum iscsi_router_state value; + char *name; +} iscsi_router_state_names[] = { + {ISCSI_ROUTER_STATE_UNKNOWN, "Unknown" }, + {ISCSI_ROUTER_STATE_ADVERTISED, "Advertised" }, + {ISCSI_ROUTER_STATE_MANUAL, "Manual" }, + {ISCSI_ROUTER_STATE_STALE, "Stale" }, +}; + +char *iscsi_get_router_state_name(enum iscsi_router_state router_state) +{ + int i; + char *state = NULL; + + for (i = 0; i < ARRAY_SIZE(iscsi_router_state_names); i++) { + if (iscsi_router_state_names[i].value == router_state) { + state = iscsi_router_state_names[i].name; + break; + } + } + return state; +} +EXPORT_SYMBOL_GPL(iscsi_get_router_state_name); + struct iscsi_iface * iscsi_create_iface(struct Scsi_Host *shost, struct iscsi_transport *transport, uint32_t iface_type, uint32_t iface_num, int dd_size) @@ -3082,6 +3416,73 @@ exit_logout_sid: } static int +iscsi_get_host_stats(struct iscsi_transport *transport, struct nlmsghdr *nlh) +{ + struct iscsi_uevent *ev = nlmsg_data(nlh); + struct Scsi_Host *shost = NULL; + struct iscsi_internal *priv; + struct sk_buff *skbhost_stats; + struct nlmsghdr *nlhhost_stats; + struct iscsi_uevent *evhost_stats; + int host_stats_size = 0; + int len, err = 0; + char *buf; + + if (!transport->get_host_stats) + return -EINVAL; + + priv = iscsi_if_transport_lookup(transport); + if (!priv) + return -EINVAL; + + host_stats_size = sizeof(struct iscsi_offload_host_stats); + len = nlmsg_total_size(sizeof(*ev) + host_stats_size); + + shost = scsi_host_lookup(ev->u.get_host_stats.host_no); + if (!shost) { + pr_err("%s: failed. Cound not find host no %u\n", + __func__, ev->u.get_host_stats.host_no); + return -ENODEV; + } + + do { + int actual_size; + + skbhost_stats = alloc_skb(len, GFP_KERNEL); + if (!skbhost_stats) { + pr_err("cannot deliver host stats: OOM\n"); + err = -ENOMEM; + goto exit_host_stats; + } + + nlhhost_stats = __nlmsg_put(skbhost_stats, 0, 0, 0, + (len - sizeof(*nlhhost_stats)), 0); + evhost_stats = nlmsg_data(nlhhost_stats); + memset(evhost_stats, 0, sizeof(*evhost_stats)); + evhost_stats->transport_handle = iscsi_handle(transport); + evhost_stats->type = nlh->nlmsg_type; + evhost_stats->u.get_host_stats.host_no = + ev->u.get_host_stats.host_no; + buf = (char *)((char *)evhost_stats + sizeof(*evhost_stats)); + memset(buf, 0, host_stats_size); + + err = transport->get_host_stats(shost, buf, host_stats_size); + + actual_size = nlmsg_total_size(sizeof(*ev) + host_stats_size); + skb_trim(skbhost_stats, NLMSG_ALIGN(actual_size)); + nlhhost_stats->nlmsg_len = actual_size; + + err = iscsi_multicast_skb(skbhost_stats, ISCSI_NL_GRP_ISCSID, + GFP_KERNEL); + } while (err < 0 && err != -ECONNREFUSED); + +exit_host_stats: + scsi_host_put(shost); + return err; +} + + +static int iscsi_if_recv_msg(struct sk_buff *skb, struct nlmsghdr *nlh, uint32_t *group) { int err = 0; @@ -3260,6 +3661,9 @@ iscsi_if_recv_msg(struct sk_buff *skb, struct nlmsghdr *nlh, uint32_t *group) err = iscsi_set_chap(transport, ev, nlmsg_attrlen(nlh, sizeof(*ev))); break; + case ISCSI_UEVENT_GET_HOST_STATS: + err = iscsi_get_host_stats(transport, nlh); + break; default: err = -ENOSYS; break; @@ -3368,6 +3772,7 @@ iscsi_conn_attr(ipv6_flow_label, ISCSI_PARAM_IPV6_FLOW_LABEL); iscsi_conn_attr(is_fw_assigned_ipv6, ISCSI_PARAM_IS_FW_ASSIGNED_IPV6); iscsi_conn_attr(tcp_xmit_wsf, ISCSI_PARAM_TCP_XMIT_WSF); iscsi_conn_attr(tcp_recv_wsf, ISCSI_PARAM_TCP_RECV_WSF); +iscsi_conn_attr(local_ipaddr, ISCSI_PARAM_LOCAL_IPADDR); #define iscsi_conn_ep_attr_show(param) \ @@ -3437,6 +3842,7 @@ static struct attribute *iscsi_conn_attrs[] = { &dev_attr_conn_is_fw_assigned_ipv6.attr, &dev_attr_conn_tcp_xmit_wsf.attr, &dev_attr_conn_tcp_recv_wsf.attr, + &dev_attr_conn_local_ipaddr.attr, NULL, }; @@ -3506,6 +3912,8 @@ static umode_t iscsi_conn_attr_is_visible(struct kobject *kobj, param = ISCSI_PARAM_TCP_XMIT_WSF; else if (attr == &dev_attr_conn_tcp_recv_wsf.attr) param = ISCSI_PARAM_TCP_RECV_WSF; + else if (attr == &dev_attr_conn_local_ipaddr.attr) + param = ISCSI_PARAM_LOCAL_IPADDR; else { WARN_ONCE(1, "Invalid conn attr"); return 0; diff --git a/drivers/scsi/scsi_transport_srp.c b/drivers/scsi/scsi_transport_srp.c index 2700a5a09bd..d47ffc8d3e4 100644 --- a/drivers/scsi/scsi_transport_srp.c +++ b/drivers/scsi/scsi_transport_srp.c @@ -64,10 +64,14 @@ static inline struct Scsi_Host *rport_to_shost(struct srp_rport *r) /** * srp_tmo_valid() - check timeout combination validity + * @reconnect_delay: Reconnect delay in seconds. + * @fast_io_fail_tmo: Fast I/O fail timeout in seconds. + * @dev_loss_tmo: Device loss timeout in seconds. * * The combination of the timeout parameters must be such that SCSI commands * are finished in a reasonable time. Hence do not allow the fast I/O fail - * timeout to exceed SCSI_DEVICE_BLOCK_MAX_TIMEOUT. Furthermore, these + * timeout to exceed SCSI_DEVICE_BLOCK_MAX_TIMEOUT nor allow dev_loss_tmo to + * exceed that limit if failing I/O fast has been disabled. Furthermore, these * parameters must be such that multipath can detect failed paths timely. * Hence do not allow all three parameters to be disabled simultaneously. */ @@ -79,6 +83,9 @@ int srp_tmo_valid(int reconnect_delay, int fast_io_fail_tmo, int dev_loss_tmo) return -EINVAL; if (fast_io_fail_tmo > SCSI_DEVICE_BLOCK_MAX_TIMEOUT) return -EINVAL; + if (fast_io_fail_tmo < 0 && + dev_loss_tmo > SCSI_DEVICE_BLOCK_MAX_TIMEOUT) + return -EINVAL; if (dev_loss_tmo >= LONG_MAX / HZ) return -EINVAL; if (fast_io_fail_tmo >= 0 && dev_loss_tmo >= 0 && @@ -368,6 +375,7 @@ invalid: /** * srp_reconnect_work() - reconnect and schedule a new attempt if necessary + * @work: Work structure used for scheduling this operation. */ static void srp_reconnect_work(struct work_struct *work) { @@ -408,6 +416,7 @@ static void __rport_fail_io_fast(struct srp_rport *rport) /** * rport_fast_io_fail_timedout() - fast I/O failure timeout handler + * @work: Work structure used for scheduling this operation. */ static void rport_fast_io_fail_timedout(struct work_struct *work) { @@ -426,6 +435,7 @@ static void rport_fast_io_fail_timedout(struct work_struct *work) /** * rport_dev_loss_timedout() - device loss timeout handler + * @work: Work structure used for scheduling this operation. */ static void rport_dev_loss_timedout(struct work_struct *work) { @@ -452,42 +462,35 @@ static void __srp_start_tl_fail_timers(struct srp_rport *rport) lockdep_assert_held(&rport->mutex); - if (!rport->deleted) { - delay = rport->reconnect_delay; - fast_io_fail_tmo = rport->fast_io_fail_tmo; - dev_loss_tmo = rport->dev_loss_tmo; - pr_debug("%s current state: %d\n", - dev_name(&shost->shost_gendev), rport->state); + delay = rport->reconnect_delay; + fast_io_fail_tmo = rport->fast_io_fail_tmo; + dev_loss_tmo = rport->dev_loss_tmo; + pr_debug("%s current state: %d\n", dev_name(&shost->shost_gendev), + rport->state); - if (delay > 0) - queue_delayed_work(system_long_wq, - &rport->reconnect_work, - 1UL * delay * HZ); - if (fast_io_fail_tmo >= 0 && - srp_rport_set_state(rport, SRP_RPORT_BLOCKED) == 0) { - pr_debug("%s new state: %d\n", - dev_name(&shost->shost_gendev), - rport->state); - scsi_target_block(&shost->shost_gendev); + if (rport->state == SRP_RPORT_LOST) + return; + if (delay > 0) + queue_delayed_work(system_long_wq, &rport->reconnect_work, + 1UL * delay * HZ); + if (srp_rport_set_state(rport, SRP_RPORT_BLOCKED) == 0) { + pr_debug("%s new state: %d\n", dev_name(&shost->shost_gendev), + rport->state); + scsi_target_block(&shost->shost_gendev); + if (fast_io_fail_tmo >= 0) queue_delayed_work(system_long_wq, &rport->fast_io_fail_work, 1UL * fast_io_fail_tmo * HZ); - } if (dev_loss_tmo >= 0) queue_delayed_work(system_long_wq, &rport->dev_loss_work, 1UL * dev_loss_tmo * HZ); - } else { - pr_debug("%s has already been deleted\n", - dev_name(&shost->shost_gendev)); - srp_rport_set_state(rport, SRP_RPORT_FAIL_FAST); - scsi_target_unblock(&shost->shost_gendev, - SDEV_TRANSPORT_OFFLINE); } } /** * srp_start_tl_fail_timers() - start the transport layer failure timers + * @rport: SRP target port. * * Start the transport layer fast I/O failure and device loss timers. Do not * modify a timer that was already started. @@ -502,6 +505,7 @@ EXPORT_SYMBOL(srp_start_tl_fail_timers); /** * scsi_request_fn_active() - number of kernel threads inside scsi_request_fn() + * @shost: SCSI host for which to count the number of scsi_request_fn() callers. */ static int scsi_request_fn_active(struct Scsi_Host *shost) { @@ -522,6 +526,7 @@ static int scsi_request_fn_active(struct Scsi_Host *shost) /** * srp_reconnect_rport() - reconnect to an SRP target port + * @rport: SRP target port. * * Blocks SCSI command queueing before invoking reconnect() such that * queuecommand() won't be invoked concurrently with reconnect() from outside @@ -556,7 +561,7 @@ int srp_reconnect_rport(struct srp_rport *rport) scsi_target_block(&shost->shost_gendev); while (scsi_request_fn_active(shost)) msleep(20); - res = i->f->reconnect(rport); + res = rport->state != SRP_RPORT_LOST ? i->f->reconnect(rport) : -ENODEV; pr_debug("%s (state %d): transport.reconnect() returned %d\n", dev_name(&shost->shost_gendev), rport->state, res); if (res == 0) { @@ -578,9 +583,9 @@ int srp_reconnect_rport(struct srp_rport *rport) spin_unlock_irq(shost->host_lock); } else if (rport->state == SRP_RPORT_RUNNING) { /* - * srp_reconnect_rport() was invoked with fast_io_fail - * off. Mark the port as failed and start the TL failure - * timers if these had not yet been started. + * srp_reconnect_rport() has been invoked with fast_io_fail + * and dev_loss off. Mark the port as failed and start the TL + * failure timers if these had not yet been started. */ __rport_fail_io_fast(rport); scsi_target_unblock(&shost->shost_gendev, @@ -599,6 +604,7 @@ EXPORT_SYMBOL(srp_reconnect_rport); /** * srp_timed_out() - SRP transport intercept of the SCSI timeout EH + * @scmd: SCSI command. * * If a timeout occurs while an rport is in the blocked state, ask the SCSI * EH to continue waiting (BLK_EH_RESET_TIMER). Otherwise let the SCSI core @@ -622,10 +628,6 @@ static void srp_rport_release(struct device *dev) { struct srp_rport *rport = dev_to_rport(dev); - cancel_delayed_work_sync(&rport->reconnect_work); - cancel_delayed_work_sync(&rport->fast_io_fail_work); - cancel_delayed_work_sync(&rport->dev_loss_work); - put_device(dev->parent); kfree(rport); } @@ -674,6 +676,7 @@ static int srp_host_match(struct attribute_container *cont, struct device *dev) /** * srp_rport_get() - increment rport reference count + * @rport: SRP target port. */ void srp_rport_get(struct srp_rport *rport) { @@ -683,6 +686,7 @@ EXPORT_SYMBOL(srp_rport_get); /** * srp_rport_put() - decrement rport reference count + * @rport: SRP target port. */ void srp_rport_put(struct srp_rport *rport) { @@ -780,12 +784,6 @@ void srp_rport_del(struct srp_rport *rport) device_del(dev); transport_destroy_device(dev); - mutex_lock(&rport->mutex); - if (rport->state == SRP_RPORT_BLOCKED) - __rport_fail_io_fast(rport); - rport->deleted = true; - mutex_unlock(&rport->mutex); - put_device(dev); } EXPORT_SYMBOL_GPL(srp_rport_del); @@ -810,6 +808,27 @@ void srp_remove_host(struct Scsi_Host *shost) } EXPORT_SYMBOL_GPL(srp_remove_host); +/** + * srp_stop_rport_timers - stop the transport layer recovery timers + * + * Must be called after srp_remove_host() and scsi_remove_host(). The caller + * must hold a reference on the rport (rport->dev) and on the SCSI host + * (rport->dev.parent). + */ +void srp_stop_rport_timers(struct srp_rport *rport) +{ + mutex_lock(&rport->mutex); + if (rport->state == SRP_RPORT_BLOCKED) + __rport_fail_io_fast(rport); + srp_rport_set_state(rport, SRP_RPORT_LOST); + mutex_unlock(&rport->mutex); + + cancel_delayed_work_sync(&rport->reconnect_work); + cancel_delayed_work_sync(&rport->fast_io_fail_work); + cancel_delayed_work_sync(&rport->dev_loss_work); +} +EXPORT_SYMBOL_GPL(srp_stop_rport_timers); + static int srp_tsk_mgmt_response(struct Scsi_Host *shost, u64 nexus, u64 tm_id, int result) { diff --git a/drivers/scsi/sd.c b/drivers/scsi/sd.c index 69725f7c32c..470954aba72 100644 --- a/drivers/scsi/sd.c +++ b/drivers/scsi/sd.c @@ -110,7 +110,7 @@ static int sd_suspend_runtime(struct device *); static int sd_resume(struct device *); static void sd_rescan(struct device *); static int sd_done(struct scsi_cmnd *); -static int sd_eh_action(struct scsi_cmnd *, unsigned char *, int, int); +static int sd_eh_action(struct scsi_cmnd *, int); static void sd_read_capacity(struct scsi_disk *sdkp, unsigned char *buffer); static void scsi_disk_release(struct device *cdev); static void sd_print_sense_hdr(struct scsi_disk *, struct scsi_sense_hdr *); @@ -801,7 +801,7 @@ static int sd_setup_write_same_cmnd(struct scsi_device *sdp, struct request *rq) if (sdkp->device->no_write_same) return BLKPREP_KILL; - BUG_ON(bio_offset(bio) || bio_iovec(bio)->bv_len != sdp->sector_size); + BUG_ON(bio_offset(bio) || bio_iovec(bio).bv_len != sdp->sector_size); sector >>= ilog2(sdp->sector_size) - 9; nr_sectors >>= ilog2(sdp->sector_size) - 9; @@ -1551,23 +1551,23 @@ static const struct block_device_operations sd_fops = { /** * sd_eh_action - error handling callback * @scmd: sd-issued command that has failed - * @eh_cmnd: The command that was sent during error handling - * @eh_cmnd_len: Length of eh_cmnd in bytes * @eh_disp: The recovery disposition suggested by the midlayer * - * This function is called by the SCSI midlayer upon completion of - * an error handling command (TEST UNIT READY, START STOP UNIT, - * etc.) The command sent to the device by the error handler is - * stored in eh_cmnd. The result of sending the eh command is - * passed in eh_disp. + * This function is called by the SCSI midlayer upon completion of an + * error test command (currently TEST UNIT READY). The result of sending + * the eh command is passed in eh_disp. We're looking for devices that + * fail medium access commands but are OK with non access commands like + * test unit ready (so wrongly see the device as having a successful + * recovery) **/ -static int sd_eh_action(struct scsi_cmnd *scmd, unsigned char *eh_cmnd, - int eh_cmnd_len, int eh_disp) +static int sd_eh_action(struct scsi_cmnd *scmd, int eh_disp) { struct scsi_disk *sdkp = scsi_disk(scmd->request->rq_disk); if (!scsi_device_online(scmd->device) || - !scsi_medium_access_command(scmd)) + !scsi_medium_access_command(scmd) || + host_byte(scmd->result) != DID_TIME_OUT || + eh_disp != SUCCESS) return eh_disp; /* @@ -1577,9 +1577,7 @@ static int sd_eh_action(struct scsi_cmnd *scmd, unsigned char *eh_cmnd, * process of recovering or has it suffered an internal failure * that prevents access to the storage medium. */ - if (host_byte(scmd->result) == DID_TIME_OUT && eh_disp == SUCCESS && - eh_cmnd_len && eh_cmnd[0] == TEST_UNIT_READY) - sdkp->medium_access_timed_out++; + sdkp->medium_access_timed_out++; /* * If the device keeps failing read/write commands but TEST UNIT @@ -1628,7 +1626,7 @@ static unsigned int sd_completed_bytes(struct scsi_cmnd *scmd) end_lba <<= 1; } else { /* be careful ... don't want any overflows */ - u64 factor = scmd->device->sector_size / 512; + unsigned int factor = scmd->device->sector_size / 512; do_div(start_lba, factor); do_div(end_lba, factor); } diff --git a/drivers/scsi/sd_dif.c b/drivers/scsi/sd_dif.c index 6174ca4ea27..a7a691d0af7 100644 --- a/drivers/scsi/sd_dif.c +++ b/drivers/scsi/sd_dif.c @@ -365,7 +365,6 @@ void sd_dif_prepare(struct request *rq, sector_t hw_sector, struct bio *bio; struct scsi_disk *sdkp; struct sd_dif_tuple *sdt; - unsigned int i, j; u32 phys, virt; sdkp = rq->bio->bi_bdev->bd_disk->private_data; @@ -376,19 +375,21 @@ void sd_dif_prepare(struct request *rq, sector_t hw_sector, phys = hw_sector & 0xffffffff; __rq_for_each_bio(bio, rq) { - struct bio_vec *iv; + struct bio_vec iv; + struct bvec_iter iter; + unsigned int j; /* Already remapped? */ if (bio_flagged(bio, BIO_MAPPED_INTEGRITY)) break; - virt = bio->bi_integrity->bip_sector & 0xffffffff; + virt = bio->bi_integrity->bip_iter.bi_sector & 0xffffffff; - bip_for_each_vec(iv, bio->bi_integrity, i) { - sdt = kmap_atomic(iv->bv_page) - + iv->bv_offset; + bip_for_each_vec(iv, bio->bi_integrity, iter) { + sdt = kmap_atomic(iv.bv_page) + + iv.bv_offset; - for (j = 0 ; j < iv->bv_len ; j += tuple_sz, sdt++) { + for (j = 0; j < iv.bv_len; j += tuple_sz, sdt++) { if (be32_to_cpu(sdt->ref_tag) == virt) sdt->ref_tag = cpu_to_be32(phys); @@ -414,7 +415,7 @@ void sd_dif_complete(struct scsi_cmnd *scmd, unsigned int good_bytes) struct scsi_disk *sdkp; struct bio *bio; struct sd_dif_tuple *sdt; - unsigned int i, j, sectors, sector_sz; + unsigned int j, sectors, sector_sz; u32 phys, virt; sdkp = scsi_disk(scmd->request->rq_disk); @@ -430,15 +431,16 @@ void sd_dif_complete(struct scsi_cmnd *scmd, unsigned int good_bytes) phys >>= 3; __rq_for_each_bio(bio, scmd->request) { - struct bio_vec *iv; + struct bio_vec iv; + struct bvec_iter iter; - virt = bio->bi_integrity->bip_sector & 0xffffffff; + virt = bio->bi_integrity->bip_iter.bi_sector & 0xffffffff; - bip_for_each_vec(iv, bio->bi_integrity, i) { - sdt = kmap_atomic(iv->bv_page) - + iv->bv_offset; + bip_for_each_vec(iv, bio->bi_integrity, iter) { + sdt = kmap_atomic(iv.bv_page) + + iv.bv_offset; - for (j = 0 ; j < iv->bv_len ; j += tuple_sz, sdt++) { + for (j = 0; j < iv.bv_len; j += tuple_sz, sdt++) { if (sectors == 0) { kunmap_atomic(sdt); diff --git a/drivers/scsi/sr.c b/drivers/scsi/sr.c index 119d67f9c47..40d85929aef 100644 --- a/drivers/scsi/sr.c +++ b/drivers/scsi/sr.c @@ -161,14 +161,10 @@ static inline struct scsi_cd *scsi_cd_get(struct gendisk *disk) goto out; cd = scsi_cd(disk); kref_get(&cd->kref); - if (scsi_device_get(cd->device)) - goto out_put; - if (!scsi_autopm_get_device(cd->device)) - goto out; - - out_put: - kref_put(&cd->kref, sr_kref_release); - cd = NULL; + if (scsi_device_get(cd->device)) { + kref_put(&cd->kref, sr_kref_release); + cd = NULL; + } out: mutex_unlock(&sr_ref_mutex); return cd; @@ -180,7 +176,6 @@ static void scsi_cd_put(struct scsi_cd *cd) mutex_lock(&sr_ref_mutex); kref_put(&cd->kref, sr_kref_release); - scsi_autopm_put_device(sdev); scsi_device_put(sdev); mutex_unlock(&sr_ref_mutex); } @@ -558,8 +553,6 @@ static int sr_block_ioctl(struct block_device *bdev, fmode_t mode, unsigned cmd, void __user *argp = (void __user *)arg; int ret; - scsi_autopm_get_device(cd->device); - mutex_lock(&sr_mutex); /* @@ -591,7 +584,6 @@ static int sr_block_ioctl(struct block_device *bdev, fmode_t mode, unsigned cmd, out: mutex_unlock(&sr_mutex); - scsi_autopm_put_device(cd->device); return ret; } @@ -599,17 +591,11 @@ static unsigned int sr_block_check_events(struct gendisk *disk, unsigned int clearing) { struct scsi_cd *cd = scsi_cd(disk); - unsigned int ret; - if (atomic_read(&cd->device->disk_events_disable_depth) == 0) { - scsi_autopm_get_device(cd->device); - ret = cdrom_check_events(&cd->cdi, clearing); - scsi_autopm_put_device(cd->device); - } else { - ret = 0; - } + if (atomic_read(&cd->device->disk_events_disable_depth)) + return 0; - return ret; + return cdrom_check_events(&cd->cdi, clearing); } static int sr_block_revalidate_disk(struct gendisk *disk) @@ -617,8 +603,6 @@ static int sr_block_revalidate_disk(struct gendisk *disk) struct scsi_cd *cd = scsi_cd(disk); struct scsi_sense_hdr sshdr; - scsi_autopm_get_device(cd->device); - /* if the unit is not ready, nothing more to do */ if (scsi_test_unit_ready(cd->device, SR_TIMEOUT, MAX_RETRIES, &sshdr)) goto out; @@ -626,7 +610,6 @@ static int sr_block_revalidate_disk(struct gendisk *disk) sr_cd_check(&cd->cdi); get_sectorsize(cd); out: - scsi_autopm_put_device(cd->device); return 0; } @@ -747,6 +730,12 @@ static int sr_probe(struct device *dev) if (register_cdrom(&cd->cdi)) goto fail_put; + /* + * Initialize block layer runtime PM stuffs before the + * periodic event checking request gets started in add_disk. + */ + blk_pm_runtime_init(sdev->request_queue, dev); + dev_set_drvdata(dev, cd); disk->flags |= GENHD_FL_REMOVABLE; add_disk(disk); diff --git a/drivers/scsi/st.c b/drivers/scsi/st.c index ff44b3c2cff..a1d6986261a 100644 --- a/drivers/scsi/st.c +++ b/drivers/scsi/st.c @@ -3719,7 +3719,7 @@ static struct st_buffer *new_tape_buffer(int need_dma, int max_sg) static int enlarge_buffer(struct st_buffer * STbuffer, int new_size, int need_dma) { - int segs, nbr, max_segs, b_size, order, got; + int segs, max_segs, b_size, order, got; gfp_t priority; if (new_size <= STbuffer->buffer_size) @@ -3729,9 +3729,6 @@ static int enlarge_buffer(struct st_buffer * STbuffer, int new_size, int need_dm normalize_buffer(STbuffer); /* Avoid extra segment */ max_segs = STbuffer->use_sg; - nbr = max_segs - STbuffer->frp_segs; - if (nbr <= 0) - return 0; priority = GFP_KERNEL | __GFP_NOWARN; if (need_dma) diff --git a/drivers/scsi/sym53c8xx_2/sym_glue.c b/drivers/scsi/sym53c8xx_2/sym_glue.c index bac55f7f69f..6d3ee1ab636 100644 --- a/drivers/scsi/sym53c8xx_2/sym_glue.c +++ b/drivers/scsi/sym53c8xx_2/sym_glue.c @@ -1531,7 +1531,7 @@ static int sym_iomap_device(struct sym_device *device) struct pci_bus_region bus_addr; int i = 2; - pcibios_resource_to_bus(pdev, &bus_addr, &pdev->resource[1]); + pcibios_resource_to_bus(pdev->bus, &bus_addr, &pdev->resource[1]); device->mmio_base = bus_addr.start; if (device->chip.features & FE_RAM) { @@ -1541,7 +1541,8 @@ static int sym_iomap_device(struct sym_device *device) */ if (!pdev->resource[i].flags) i++; - pcibios_resource_to_bus(pdev, &bus_addr, &pdev->resource[i]); + pcibios_resource_to_bus(pdev->bus, &bus_addr, + &pdev->resource[i]); device->ram_base = bus_addr.start; } diff --git a/drivers/scsi/virtio_scsi.c b/drivers/scsi/virtio_scsi.c index c3173dced87..16bfd50cd3f 100644 --- a/drivers/scsi/virtio_scsi.c +++ b/drivers/scsi/virtio_scsi.c @@ -956,6 +956,10 @@ static void virtscsi_remove(struct virtio_device *vdev) #ifdef CONFIG_PM_SLEEP static int virtscsi_freeze(struct virtio_device *vdev) { + struct Scsi_Host *sh = virtio_scsi_host(vdev); + struct virtio_scsi *vscsi = shost_priv(sh); + + unregister_hotcpu_notifier(&vscsi->nb); virtscsi_remove_vqs(vdev); return 0; } @@ -964,8 +968,17 @@ static int virtscsi_restore(struct virtio_device *vdev) { struct Scsi_Host *sh = virtio_scsi_host(vdev); struct virtio_scsi *vscsi = shost_priv(sh); + int err; + + err = virtscsi_init(vdev, vscsi); + if (err) + return err; + + err = register_hotcpu_notifier(&vscsi->nb); + if (err) + vdev->config->del_vqs(vdev); - return virtscsi_init(vdev, vscsi); + return err; } #endif diff --git a/drivers/scsi/zorro7xx.c b/drivers/scsi/zorro7xx.c index cbf3476c68c..aff31991aea 100644 --- a/drivers/scsi/zorro7xx.c +++ b/drivers/scsi/zorro7xx.c @@ -104,7 +104,7 @@ static int zorro7xx_init_one(struct zorro_dev *z, if (ioaddr > 0x01000000) hostdata->base = ioremap(ioaddr, zorro_resource_len(z)); else - hostdata->base = (void __iomem *)ZTWO_VADDR(ioaddr); + hostdata->base = ZTWO_VADDR(ioaddr); hostdata->clock = 50; hostdata->chip710 = 1; |