diff options
Diffstat (limited to 'drivers/serial/Kconfig')
| -rw-r--r-- | drivers/serial/Kconfig | 72 |
1 files changed, 5 insertions, 67 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index ec3c214598d..c1df7676a73 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -776,24 +776,7 @@ config BFIN_UART0_CTSRTS bool "Enable UART0 hardware flow control" depends on SERIAL_BFIN_UART0 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART0_CTS_PIN - int "UART0 CTS pin" - depends on BFIN_UART0_CTSRTS && !BF548 - default 23 - help - The default pin is GPIO_GP7. - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART0_RTS_PIN - int "UART0 RTS pin" - depends on BFIN_UART0_CTSRTS && !BF548 - default 22 - help - The default pin is GPIO_GP6. - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_BFIN_UART1 bool "Enable UART1" @@ -805,22 +788,7 @@ config BFIN_UART1_CTSRTS bool "Enable UART1 hardware flow control" depends on SERIAL_BFIN_UART1 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART1_CTS_PIN - int "UART1 CTS pin" - depends on BFIN_UART1_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART1_RTS_PIN - int "UART1 RTS pin" - depends on BFIN_UART1_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_BFIN_UART2 bool "Enable UART2" @@ -832,22 +800,7 @@ config BFIN_UART2_CTSRTS bool "Enable UART2 hardware flow control" depends on SERIAL_BFIN_UART2 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART2_CTS_PIN - int "UART2 CTS pin" - depends on BFIN_UART2_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART2_RTS_PIN - int "UART2 RTS pin" - depends on BFIN_UART2_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_BFIN_UART3 bool "Enable UART3" @@ -859,22 +812,7 @@ config BFIN_UART3_CTSRTS bool "Enable UART3 hardware flow control" depends on SERIAL_BFIN_UART3 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART3_CTS_PIN - int "UART3 CTS pin" - depends on BFIN_UART3_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART3_RTS_PIN - int "UART3 RTS pin" - depends on BFIN_UART3_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_IMX bool "IMX serial port support" @@ -1412,7 +1350,7 @@ config SERIAL_NETX_CONSOLE config SERIAL_OF_PLATFORM tristate "Serial port on Open Firmware platform bus" - depends on PPC_OF || MICROBLAZE + depends on OF depends on SERIAL_8250 || SERIAL_OF_PLATFORM_NWPSERIAL help If you have a PowerPC based system that has serial ports |