diff options
Diffstat (limited to 'drivers/serial/Kconfig')
| -rw-r--r-- | drivers/serial/Kconfig | 97 |
1 files changed, 30 insertions, 67 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index aff9dcd051c..c1df7676a73 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -776,24 +776,7 @@ config BFIN_UART0_CTSRTS bool "Enable UART0 hardware flow control" depends on SERIAL_BFIN_UART0 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART0_CTS_PIN - int "UART0 CTS pin" - depends on BFIN_UART0_CTSRTS && !BF548 - default 23 - help - The default pin is GPIO_GP7. - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART0_RTS_PIN - int "UART0 RTS pin" - depends on BFIN_UART0_CTSRTS && !BF548 - default 22 - help - The default pin is GPIO_GP6. - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_BFIN_UART1 bool "Enable UART1" @@ -805,22 +788,7 @@ config BFIN_UART1_CTSRTS bool "Enable UART1 hardware flow control" depends on SERIAL_BFIN_UART1 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART1_CTS_PIN - int "UART1 CTS pin" - depends on BFIN_UART1_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART1_RTS_PIN - int "UART1 RTS pin" - depends on BFIN_UART1_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_BFIN_UART2 bool "Enable UART2" @@ -832,22 +800,7 @@ config BFIN_UART2_CTSRTS bool "Enable UART2 hardware flow control" depends on SERIAL_BFIN_UART2 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART2_CTS_PIN - int "UART2 CTS pin" - depends on BFIN_UART2_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART2_RTS_PIN - int "UART2 RTS pin" - depends on BFIN_UART2_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_BFIN_UART3 bool "Enable UART3" @@ -859,22 +812,7 @@ config BFIN_UART3_CTSRTS bool "Enable UART3 hardware flow control" depends on SERIAL_BFIN_UART3 help - Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS - signal. - -config UART3_CTS_PIN - int "UART3 CTS pin" - depends on BFIN_UART3_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. - -config UART3_RTS_PIN - int "UART3 RTS pin" - depends on BFIN_UART3_CTSRTS && !BF548 - default -1 - help - Refer to arch/blackfin/mach-*/include/mach/gpio.h to see the GPIO map. + Enable hardware flow control in the driver. config SERIAL_IMX bool "IMX serial port support" @@ -1381,6 +1319,16 @@ config SERIAL_MSM_CONSOLE depends on SERIAL_MSM=y select SERIAL_CORE_CONSOLE +config SERIAL_VT8500 + bool "VIA VT8500 on-chip serial port support" + depends on ARM && ARCH_VT8500 + select SERIAL_CORE + +config SERIAL_VT8500_CONSOLE + bool "VIA VT8500 serial console support" + depends on SERIAL_VT8500=y + select SERIAL_CORE_CONSOLE + config SERIAL_NETX tristate "NetX serial port support" depends on ARM && ARCH_NETX @@ -1402,7 +1350,7 @@ config SERIAL_NETX_CONSOLE config SERIAL_OF_PLATFORM tristate "Serial port on Open Firmware platform bus" - depends on PPC_OF || MICROBLAZE + depends on OF depends on SERIAL_8250 || SERIAL_OF_PLATFORM_NWPSERIAL help If you have a PowerPC based system that has serial ports @@ -1632,4 +1580,19 @@ config SERIAL_ALTERA_UART_CONSOLE help Enable a Altera UART port to be the system console. +config SERIAL_IFX6X60 + tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)" + depends on GPIOLIB && SPI && EXPERIMENTAL + help + Support for the IFX6x60 modem devices on Intel MID platforms. + +config SERIAL_PCH_UART + tristate "Intel EG20T PCH UART" + depends on PCI && DMADEVICES + select SERIAL_CORE + select PCH_DMA + help + This driver is for PCH(Platform controller Hub) UART of Intel EG20T + which is an IOH(Input/Output Hub) for x86 embedded processor. + Enabling PCH_DMA, this PCH UART works as DMA mode. endmenu |