summaryrefslogtreecommitdiffstats
path: root/drivers/serial/bfin_5xx.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial/bfin_5xx.c')
-rw-r--r--drivers/serial/bfin_5xx.c297
1 files changed, 199 insertions, 98 deletions
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 318d69dce8e..18ba812a4f8 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -63,7 +63,6 @@ static int kgdboc_break_enabled;
#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
#define DMA_RX_FLUSH_JIFFIES (HZ / 50)
-#define CTS_CHECK_JIFFIES (HZ / 50)
#ifdef CONFIG_SERIAL_BFIN_DMA
static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
@@ -71,10 +70,65 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
#endif
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
-
static void bfin_serial_reset_irda(struct uart_port *port);
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->cts_pin < 0)
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ /* CTS PIN is negative assertive. */
+ if (UART_GET_CTS(uart))
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+ else
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->rts_pin < 0)
+ return;
+
+ /* RTS PIN is negative assertive. */
+ if (mctrl & TIOCM_RTS)
+ UART_ENABLE_RTS(uart);
+ else
+ UART_DISABLE_RTS(uart);
+}
+
+/*
+ * Handle any change of modem status signal.
+ */
+static irqreturn_t bfin_serial_mctrl_cts_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ unsigned int status;
+
+ status = bfin_serial_get_mctrl(&uart->port);
+ uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ uart->scts = 1;
+ UART_CLEAR_SCTS(uart);
+ UART_CLEAR_IER(uart, EDSSI);
+#endif
+
+ return IRQ_HANDLED;
+}
+#else
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+}
+#endif
+
/*
* interrupts are disabled on entry
*/
@@ -111,6 +165,13 @@ static void bfin_serial_start_tx(struct uart_port *port)
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
struct tty_struct *tty = uart->port.info->port.tty;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
/*
* To avoid losting RX interrupt, we reset IR function
* before sending data.
@@ -174,10 +235,10 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
return;
}
- if (!uart->port.info || !uart->port.info->tty)
+ if (!uart->port.info || !uart->port.info->port.tty)
return;
#endif
- tty = uart->port.info->tty;
+ tty = uart->port.info->port.tty;
if (ANOMALY_05000363) {
/* The BF533 (and BF561) family of processors have a nice anomaly
@@ -264,12 +325,6 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
{
struct circ_buf *xmit = &uart->port.info->xmit;
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
#ifdef CONFIG_BF54x
/* Clear TFI bit */
@@ -312,6 +367,12 @@ static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
spin_lock(&uart->port.lock);
if (UART_GET_LSR(uart) & THRE)
bfin_serial_tx_chars(uart);
@@ -328,12 +389,6 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
uart->tx_done = 0;
- /*
- * Check the modem control lines before
- * transmitting anything.
- */
- bfin_serial_mctrl_check(uart);
-
if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
uart->tx_count = 0;
uart->tx_done = 1;
@@ -401,9 +456,11 @@ static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
else
flg = TTY_NORMAL;
- for (i = uart->rx_dma_buf.tail; i != uart->rx_dma_buf.head; i++) {
+ for (i = uart->rx_dma_buf.tail; ; i++) {
if (i >= UART_XMIT_SIZE)
i = 0;
+ if (i == uart->rx_dma_buf.head)
+ break;
if (!uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
uart_insert_char(&uart->port, status, OE,
uart->rx_dma_buf.buf[i], flg);
@@ -415,7 +472,8 @@ static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
{
- int x_pos, pos, flags;
+ int x_pos, pos;
+ unsigned long flags;
spin_lock_irqsave(&uart->port.lock, flags);
@@ -445,6 +503,13 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
struct bfin_serial_port *uart = dev_id;
struct circ_buf *xmit = &uart->port.info->xmit;
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ uart->scts = 0;
+ uart_handle_cts_change(&uart->port, uart->scts);
+ }
+#endif
+
spin_lock(&uart->port.lock);
if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
disable_dma(uart->tx_dma_channel);
@@ -493,61 +558,6 @@ static unsigned int bfin_serial_tx_empty(struct uart_port *port)
return 0;
}
-static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->cts_pin < 0)
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-
- if (UART_GET_CTS(uart))
- return TIOCM_DSR | TIOCM_CAR;
- else
-#endif
- return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
-}
-
-static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
- if (uart->rts_pin < 0)
- return;
-
- if (mctrl & TIOCM_RTS)
- UART_CLEAR_RTS(uart);
- else
- UART_SET_RTS(uart);
-#endif
-}
-
-/*
- * Handle any change of modem status signal since we were last called.
- */
-static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
-{
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- unsigned int status;
- struct uart_info *info = uart->port.info;
- struct tty_struct *tty = info->port.tty;
-
- status = bfin_serial_get_mctrl(&uart->port);
- uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
- if (!(status & TIOCM_CTS)) {
- tty->hw_stopped = 1;
- uart->cts_timer.data = (unsigned long)(uart);
- uart->cts_timer.function = (void *)bfin_serial_mctrl_check;
- uart->cts_timer.expires = jiffies + CTS_CHECK_JIFFIES;
- add_timer(&(uart->cts_timer));
- } else {
- tty->hw_stopped = 0;
- }
-#endif
-}
-
-/*
- * Interrupts are always disabled.
- */
static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
@@ -603,7 +613,7 @@ static int bfin_serial_startup(struct uart_port *port)
uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
add_timer(&(uart->rx_dma_timer));
#else
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
if (kgdboc_port_line == uart->port.line && kgdboc_break_enabled)
kgdboc_break_enabled = 0;
@@ -658,11 +668,50 @@ static int bfin_serial_startup(struct uart_port *port)
}
}
# endif
-#if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
+# if defined(CONFIG_KGDB_SERIAL_CONSOLE) || \
defined(CONFIG_KGDB_SERIAL_CONSOLE_MODULE)
}
# endif
#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0) {
+ if (request_irq(gpio_to_irq(uart->cts_pin),
+ bfin_serial_mctrl_cts_int,
+ IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING |
+ IRQF_DISABLED, "BFIN_UART_CTS", uart)) {
+ uart->cts_pin = -1;
+ pr_info("Unable to attach BlackFin UART CTS interrupt.\
+ So, disable it.\n");
+ }
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (request_irq(uart->status_irq,
+ bfin_serial_mctrl_cts_int,
+ IRQF_DISABLED, "BFIN_UART_MODEM_STATUS", uart)) {
+ pr_info("Unable to attach BlackFin UART Modem \
+ Status interrupt.\n");
+ }
+
+ if (uart->cts_pin >= 0) {
+ gpio_request(uart->cts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->cts_pin, 1);
+ }
+ if (uart->rts_pin >= 0) {
+ gpio_request(uart->rts_pin, DRIVER_NAME);
+ gpio_direction_output(uart->rts_pin, 0);
+ }
+
+ /* CTS RTS PINs are negative assertive. */
+ UART_PUT_MCR(uart, ACTS);
+ UART_SET_IER(uart, EDSSI);
+#endif
+
UART_SET_IER(uart, ERBFI);
return 0;
}
@@ -696,6 +745,21 @@ static void bfin_serial_shutdown(struct uart_port *port)
free_irq(uart->port.irq, uart);
free_irq(uart->port.irq+1, uart);
#endif
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ if (uart->cts_pin >= 0)
+ free_irq(gpio_to_irq(uart->cts_pin), uart);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+#endif
+#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
+ if (uart->cts_pin >= 0)
+ gpio_free(uart->cts_pin);
+ if (uart->rts_pin >= 0)
+ gpio_free(uart->rts_pin);
+ if (UART_GET_IER(uart) && EDSSI)
+ free_irq(uart->status_irq, uart);
+#endif
}
static void
@@ -757,7 +821,7 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
}
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
- quot = uart_get_divisor(port, baud);
+ quot = uart_get_divisor(port, baud) - ANOMALY_05000230;
spin_lock_irqsave(&uart->port.lock, flags);
UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15);
@@ -861,6 +925,20 @@ static void bfin_serial_set_ldisc(struct uart_port *port)
}
}
+static void bfin_serial_reset_irda(struct uart_port *port)
+{
+ int line = port->line;
+ unsigned short val;
+
+ val = UART_GET_GCTL(&bfin_serial_ports[line]);
+ val &= ~(IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+ val |= (IREN | RPOLC);
+ UART_PUT_GCTL(&bfin_serial_ports[line], val);
+ SSYNC();
+}
+
#ifdef CONFIG_CONSOLE_POLL
static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
{
@@ -906,20 +984,6 @@ static int bfin_kgdboc_port_startup(struct uart_port *port)
}
#endif
-static void bfin_serial_reset_irda(struct uart_port *port)
-{
- int line = port->line;
- unsigned short val;
-
- val = UART_GET_GCTL(&bfin_serial_ports[line]);
- val &= ~(IREN | RPOLC);
- UART_PUT_GCTL(&bfin_serial_ports[line], val);
- SSYNC();
- val |= (IREN | RPOLC);
- UART_PUT_GCTL(&bfin_serial_ports[line], val);
- SSYNC();
-}
-
static struct uart_ops bfin_serial_pops = {
.tx_empty = bfin_serial_tx_empty,
.set_mctrl = bfin_serial_set_mctrl,
@@ -949,6 +1013,39 @@ static struct uart_ops bfin_serial_pops = {
#endif
};
+static void __init bfin_serial_hw_init(void)
+{
+#ifdef CONFIG_SERIAL_BFIN_UART0
+ peripheral_request(P_UART0_TX, DRIVER_NAME);
+ peripheral_request(P_UART0_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART1
+ peripheral_request(P_UART1_TX, DRIVER_NAME);
+ peripheral_request(P_UART1_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART1_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART1_RTS, DRIVER_NAME);
+ peripheral_request(P_UART1_CTS, DRIVER_NAME);
+# endif
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART2
+ peripheral_request(P_UART2_TX, DRIVER_NAME);
+ peripheral_request(P_UART2_RX, DRIVER_NAME);
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_UART3
+ peripheral_request(P_UART3_TX, DRIVER_NAME);
+ peripheral_request(P_UART3_RX, DRIVER_NAME);
+
+# if defined(CONFIG_BFIN_UART3_CTSRTS) && defined(CONFIG_BF54x)
+ peripheral_request(P_UART3_RTS, DRIVER_NAME);
+ peripheral_request(P_UART3_CTS, DRIVER_NAME);
+# endif
+#endif
+}
+
static void __init bfin_serial_init_ports(void)
{
static int first = 1;
@@ -958,6 +1055,8 @@ static void __init bfin_serial_init_ports(void)
return;
first = 0;
+ bfin_serial_hw_init();
+
for (i = 0; i < nr_active_ports; i++) {
bfin_serial_ports[i].port.uartclk = get_sclk();
bfin_serial_ports[i].port.fifosize = BFIN_UART_TX_FIFO_SIZE;
@@ -970,6 +1069,8 @@ static void __init bfin_serial_init_ports(void)
bfin_serial_resource[i].uart_base_addr;
bfin_serial_ports[i].port.irq =
bfin_serial_resource[i].uart_irq;
+ bfin_serial_ports[i].status_irq =
+ bfin_serial_resource[i].uart_status_irq;
bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF;
#ifdef CONFIG_SERIAL_BFIN_DMA
bfin_serial_ports[i].tx_done = 1;
@@ -980,16 +1081,14 @@ static void __init bfin_serial_init_ports(void)
bfin_serial_resource[i].uart_rx_dma_channel;
init_timer(&(bfin_serial_ports[i].rx_dma_timer));
#endif
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
- init_timer(&(bfin_serial_ports[i].cts_timer));
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
bfin_serial_ports[i].cts_pin =
bfin_serial_resource[i].uart_cts_pin;
bfin_serial_ports[i].rts_pin =
bfin_serial_resource[i].uart_rts_pin;
#endif
- bfin_serial_hw_init(&bfin_serial_ports[i]);
}
-
}
#if defined(CONFIG_SERIAL_BFIN_CONSOLE) || defined(CONFIG_EARLY_PRINTK)
@@ -1046,7 +1145,8 @@ bfin_serial_console_setup(struct console *co, char *options)
int baud = 57600;
int bits = 8;
int parity = 'n';
-# ifdef CONFIG_SERIAL_BFIN_CTSRTS
+# if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
int flow = 'r';
# else
int flow = 'n';
@@ -1088,7 +1188,7 @@ static void
bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
{
struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
- int flags = 0;
+ unsigned long flags;
spin_lock_irqsave(&uart->port.lock, flags);
uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
@@ -1243,7 +1343,8 @@ static int bfin_serial_remove(struct platform_device *dev)
continue;
uart_remove_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
bfin_serial_ports[i].port.dev = NULL;
-#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
+ defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
gpio_free(bfin_serial_ports[i].cts_pin);
gpio_free(bfin_serial_ports[i].rts_pin);
#endif