diff options
Diffstat (limited to 'drivers/serial/crisv10.c')
| -rw-r--r-- | drivers/serial/crisv10.c | 22 |
1 files changed, 11 insertions, 11 deletions
diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c index 901be348345..cabd048c863 100644 --- a/drivers/serial/crisv10.c +++ b/drivers/serial/crisv10.c @@ -415,7 +415,7 @@ * Fixed DEF_TX value that caused the serial transmitter pin (txd) to go to 0 when * closing the last filehandle, NASTY!. * Added break generation, not tested though! - * Use SA_SHIRQ when request_irq() for ser2 and ser3 (shared with) par0 and par1. + * Use IRQF_SHARED when request_irq() for ser2 and ser3 (shared with) par0 and par1. * You can't use them at the same time (yet..), but you can hopefully switch * between ser2/par0, ser3/par1 with the same kernel config. * Replaced some magic constants with defines @@ -4942,55 +4942,55 @@ rs_init(void) /* Not needed in simulator. May only complicate stuff. */ /* hook the irq's for DMA channel 6 and 7, serial output and input, and some more... */ - if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial ", NULL)) + if (request_irq(SERIAL_IRQ_NBR, ser_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial ", NULL)) panic("irq8"); #ifdef CONFIG_ETRAX_SERIAL_PORT0 #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA6_OUT - if (request_irq(SER0_DMA_TX_IRQ_NBR, tr_interrupt, SA_INTERRUPT, "serial 0 dma tr", NULL)) + if (request_irq(SER0_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 0 dma tr", NULL)) panic("irq22"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT0_DMA7_IN - if (request_irq(SER0_DMA_RX_IRQ_NBR, rec_interrupt, SA_INTERRUPT, "serial 0 dma rec", NULL)) + if (request_irq(SER0_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 0 dma rec", NULL)) panic("irq23"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_PORT1 #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA8_OUT - if (request_irq(SER1_DMA_TX_IRQ_NBR, tr_interrupt, SA_INTERRUPT, "serial 1 dma tr", NULL)) + if (request_irq(SER1_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_DISABLED, "serial 1 dma tr", NULL)) panic("irq24"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT1_DMA9_IN - if (request_irq(SER1_DMA_RX_IRQ_NBR, rec_interrupt, SA_INTERRUPT, "serial 1 dma rec", NULL)) + if (request_irq(SER1_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_DISABLED, "serial 1 dma rec", NULL)) panic("irq25"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_PORT2 /* DMA Shared with par0 (and SCSI0 and ATA) */ #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA2_OUT - if (request_irq(SER2_DMA_TX_IRQ_NBR, tr_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 2 dma tr", NULL)) + if (request_irq(SER2_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma tr", NULL)) panic("irq18"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT2_DMA3_IN - if (request_irq(SER2_DMA_RX_IRQ_NBR, rec_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 2 dma rec", NULL)) + if (request_irq(SER2_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 2 dma rec", NULL)) panic("irq19"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_PORT3 /* DMA Shared with par1 (and SCSI1 and Extern DMA 0) */ #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA4_OUT - if (request_irq(SER3_DMA_TX_IRQ_NBR, tr_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 3 dma tr", NULL)) + if (request_irq(SER3_DMA_TX_IRQ_NBR, tr_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma tr", NULL)) panic("irq20"); #endif #ifdef CONFIG_ETRAX_SERIAL_PORT3_DMA5_IN - if (request_irq(SER3_DMA_RX_IRQ_NBR, rec_interrupt, SA_SHIRQ | SA_INTERRUPT, "serial 3 dma rec", NULL)) + if (request_irq(SER3_DMA_RX_IRQ_NBR, rec_interrupt, IRQF_SHARED | IRQF_DISABLED, "serial 3 dma rec", NULL)) panic("irq21"); #endif #endif #ifdef CONFIG_ETRAX_SERIAL_FLUSH_DMA_FAST - if (request_irq(TIMER1_IRQ_NBR, timeout_interrupt, SA_SHIRQ | SA_INTERRUPT, + if (request_irq(TIMER1_IRQ_NBR, timeout_interrupt, IRQF_SHARED | IRQF_DISABLED, "fast serial dma timeout", NULL)) { printk(KERN_CRIT "err: timer1 irq\n"); } |