diff options
Diffstat (limited to 'drivers/serial/max3107.h')
| -rw-r--r-- | drivers/serial/max3107.h | 441 |
1 files changed, 441 insertions, 0 deletions
diff --git a/drivers/serial/max3107.h b/drivers/serial/max3107.h new file mode 100644 index 00000000000..7ab63239250 --- /dev/null +++ b/drivers/serial/max3107.h @@ -0,0 +1,441 @@ +/* + * max3107.h - spi uart protocol driver header for Maxim 3107 + * + * Copyright (C) Aavamobile 2009 + * Based on serial_max3100.h by Christian Pellegrin + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef _MAX3107_H +#define _MAX3107_H + +/* Serial error status definitions */ +#define MAX3107_PARITY_ERROR 1 +#define MAX3107_FRAME_ERROR 2 +#define MAX3107_OVERRUN_ERROR 4 +#define MAX3107_ALL_ERRORS (MAX3107_PARITY_ERROR | \ + MAX3107_FRAME_ERROR | \ + MAX3107_OVERRUN_ERROR) + +/* GPIO definitions */ +#define MAX3107_GPIO_BASE 88 +#define MAX3107_GPIO_COUNT 4 + + +/* GPIO connected to chip's reset pin */ +#define MAX3107_RESET_GPIO 87 + + +/* Chip reset delay */ +#define MAX3107_RESET_DELAY 10 + +/* Chip wakeup delay */ +#define MAX3107_WAKEUP_DELAY 50 + + +/* Sleep mode definitions */ +#define MAX3107_DISABLE_FORCED_SLEEP 0 +#define MAX3107_ENABLE_FORCED_SLEEP 1 +#define MAX3107_DISABLE_AUTOSLEEP 2 +#define MAX3107_ENABLE_AUTOSLEEP 3 + + +/* Definitions for register access with SPI transfers + * + * SPI transfer format: + * + * Master to slave bits xzzzzzzzyyyyyyyy + * Slave to master bits aaaaaaaabbbbbbbb + * + * where: + * x = 0 for reads, 1 for writes + * z = register address + * y = new register value if write, 0 if read + * a = unspecified + * b = register value if read, unspecified if write + */ + +/* SPI speed */ +#define MAX3107_SPI_SPEED (3125000 * 2) + +/* Write bit */ +#define MAX3107_WRITE_BIT (1 << 15) + +/* SPI TX data mask */ +#define MAX3107_SPI_RX_DATA_MASK (0x00ff) + +/* SPI RX data mask */ +#define MAX3107_SPI_TX_DATA_MASK (0x00ff) + +/* Register access masks */ +#define MAX3107_RHR_REG (0x0000) /* RX FIFO */ +#define MAX3107_THR_REG (0x0000) /* TX FIFO */ +#define MAX3107_IRQEN_REG (0x0100) /* IRQ enable */ +#define MAX3107_IRQSTS_REG (0x0200) /* IRQ status */ +#define MAX3107_LSR_IRQEN_REG (0x0300) /* LSR IRQ enable */ +#define MAX3107_LSR_IRQSTS_REG (0x0400) /* LSR IRQ status */ +#define MAX3107_SPCHR_IRQEN_REG (0x0500) /* Special char IRQ enable */ +#define MAX3107_SPCHR_IRQSTS_REG (0x0600) /* Special char IRQ status */ +#define MAX3107_STS_IRQEN_REG (0x0700) /* Status IRQ enable */ +#define MAX3107_STS_IRQSTS_REG (0x0800) /* Status IRQ status */ +#define MAX3107_MODE1_REG (0x0900) /* MODE1 */ +#define MAX3107_MODE2_REG (0x0a00) /* MODE2 */ +#define MAX3107_LCR_REG (0x0b00) /* LCR */ +#define MAX3107_RXTO_REG (0x0c00) /* RX timeout */ +#define MAX3107_HDPIXDELAY_REG (0x0d00) /* Auto transceiver delays */ +#define MAX3107_IRDA_REG (0x0e00) /* IRDA settings */ +#define MAX3107_FLOWLVL_REG (0x0f00) /* Flow control levels */ +#define MAX3107_FIFOTRIGLVL_REG (0x1000) /* FIFO IRQ trigger levels */ +#define MAX3107_TXFIFOLVL_REG (0x1100) /* TX FIFO level */ +#define MAX3107_RXFIFOLVL_REG (0x1200) /* RX FIFO level */ +#define MAX3107_FLOWCTRL_REG (0x1300) /* Flow control */ +#define MAX3107_XON1_REG (0x1400) /* XON1 character */ +#define MAX3107_XON2_REG (0x1500) /* XON2 character */ +#define MAX3107_XOFF1_REG (0x1600) /* XOFF1 character */ +#define MAX3107_XOFF2_REG (0x1700) /* XOFF2 character */ +#define MAX3107_GPIOCFG_REG (0x1800) /* GPIO config */ +#define MAX3107_GPIODATA_REG (0x1900) /* GPIO data */ +#define MAX3107_PLLCFG_REG (0x1a00) /* PLL config */ +#define MAX3107_BRGCFG_REG (0x1b00) /* Baud rate generator conf */ +#define MAX3107_BRGDIVLSB_REG (0x1c00) /* Baud rate divisor LSB */ +#define MAX3107_BRGDIVMSB_REG (0x1d00) /* Baud rate divisor MSB */ +#define MAX3107_CLKSRC_REG (0x1e00) /* Clock source */ +#define MAX3107_REVID_REG (0x1f00) /* Revision identification */ + +/* IRQ register bits */ +#define MAX3107_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */ +#define MAX3107_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */ +#define MAX3107_IRQ_STS_BIT (1 << 2) /* Status interrupt */ +#define MAX3107_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */ +#define MAX3107_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */ +#define MAX3107_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */ +#define MAX3107_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */ +#define MAX3107_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */ + +/* LSR register bits */ +#define MAX3107_LSR_RXTO_BIT (1 << 0) /* RX timeout */ +#define MAX3107_LSR_RXOVR_BIT (1 << 1) /* RX overrun */ +#define MAX3107_LSR_RXPAR_BIT (1 << 2) /* RX parity error */ +#define MAX3107_LSR_FRERR_BIT (1 << 3) /* Frame error */ +#define MAX3107_LSR_RXBRK_BIT (1 << 4) /* RX break */ +#define MAX3107_LSR_RXNOISE_BIT (1 << 5) /* RX noise */ +#define MAX3107_LSR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_LSR_CTS_BIT (1 << 7) /* CTS pin state */ + +/* Special character register bits */ +#define MAX3107_SPCHR_XON1_BIT (1 << 0) /* XON1 character */ +#define MAX3107_SPCHR_XON2_BIT (1 << 1) /* XON2 character */ +#define MAX3107_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */ +#define MAX3107_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */ +#define MAX3107_SPCHR_BREAK_BIT (1 << 4) /* RX break */ +#define MAX3107_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */ +#define MAX3107_SPCHR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_SPCHR_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* Status register bits */ +#define MAX3107_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */ +#define MAX3107_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */ +#define MAX3107_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */ +#define MAX3107_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */ +#define MAX3107_STS_UNDEF4_BIT (1 << 4) /* Undefined/not used */ +#define MAX3107_STS_CLKREADY_BIT (1 << 5) /* Clock ready */ +#define MAX3107_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */ +#define MAX3107_STS_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* MODE1 register bits */ +#define MAX3107_MODE1_RXDIS_BIT (1 << 0) /* RX disable */ +#define MAX3107_MODE1_TXDIS_BIT (1 << 1) /* TX disable */ +#define MAX3107_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */ +#define MAX3107_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */ +#define MAX3107_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */ +#define MAX3107_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */ +#define MAX3107_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */ +#define MAX3107_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */ + +/* MODE2 register bits */ +#define MAX3107_MODE2_RST_BIT (1 << 0) /* Chip reset */ +#define MAX3107_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */ +#define MAX3107_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */ +#define MAX3107_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */ +#define MAX3107_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */ +#define MAX3107_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */ +#define MAX3107_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */ +#define MAX3107_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */ + +/* LCR register bits */ +#define MAX3107_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ +#define MAX3107_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 + * + * Word length bits table: + * 00 -> 5 bit words + * 01 -> 6 bit words + * 10 -> 7 bit words + * 11 -> 8 bit words + */ +#define MAX3107_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit + * + * STOP length bit table: + * 0 -> 1 stop bit + * 1 -> 1-1.5 stop bits if + * word length is 5, + * 2 stop bits otherwise + */ +#define MAX3107_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ +#define MAX3107_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ +#define MAX3107_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ +#define MAX3107_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ +#define MAX3107_LCR_RTS_BIT (1 << 7) /* RTS pin control */ +#define MAX3107_LCR_WORD_LEN_5 (0x0000) +#define MAX3107_LCR_WORD_LEN_6 (0x0001) +#define MAX3107_LCR_WORD_LEN_7 (0x0002) +#define MAX3107_LCR_WORD_LEN_8 (0x0003) + + +/* IRDA register bits */ +#define MAX3107_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */ +#define MAX3107_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */ +#define MAX3107_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */ +#define MAX3107_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */ +#define MAX3107_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */ +#define MAX3107_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */ +#define MAX3107_IRDA_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_IRDA_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* Flow control trigger level register masks */ +#define MAX3107_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */ +#define MAX3107_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */ +#define MAX3107_FLOWLVL_HALT(words) ((words/8) & 0x000f) +#define MAX3107_FLOWLVL_RES(words) (((words/8) & 0x000f) << 4) + +/* FIFO interrupt trigger level register masks */ +#define MAX3107_FIFOTRIGLVL_TX_MASK (0x000f) /* TX FIFO trigger level */ +#define MAX3107_FIFOTRIGLVL_RX_MASK (0x00f0) /* RX FIFO trigger level */ +#define MAX3107_FIFOTRIGLVL_TX(words) ((words/8) & 0x000f) +#define MAX3107_FIFOTRIGLVL_RX(words) (((words/8) & 0x000f) << 4) + +/* Flow control register bits */ +#define MAX3107_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */ +#define MAX3107_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */ +#define MAX3107_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs + * are used in conjunction with + * XOFF2 for definition of + * special character */ +#define MAX3107_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */ +#define MAX3107_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */ +#define MAX3107_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1 + * + * SWFLOW bits 1 & 0 table: + * 00 -> no transmitter flow + * control + * 01 -> receiver compares + * XON2 and XOFF2 + * and controls + * transmitter + * 10 -> receiver compares + * XON1 and XOFF1 + * and controls + * transmitter + * 11 -> receiver compares + * XON1, XON2, XOFF1 and + * XOFF2 and controls + * transmitter + */ +#define MAX3107_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */ +#define MAX3107_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3 + * + * SWFLOW bits 3 & 2 table: + * 00 -> no received flow + * control + * 01 -> transmitter generates + * XON2 and XOFF2 + * 10 -> transmitter generates + * XON1 and XOFF1 + * 11 -> transmitter generates + * XON1, XON2, XOFF1 and + * XOFF2 + */ + +/* GPIO configuration register bits */ +#define MAX3107_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */ +#define MAX3107_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */ +#define MAX3107_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */ +#define MAX3107_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */ +#define MAX3107_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */ +#define MAX3107_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */ +#define MAX3107_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */ +#define MAX3107_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */ + +/* GPIO DATA register bits */ +#define MAX3107_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */ +#define MAX3107_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */ +#define MAX3107_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */ +#define MAX3107_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */ +#define MAX3107_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */ +#define MAX3107_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */ +#define MAX3107_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */ +#define MAX3107_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */ + +/* PLL configuration register masks */ +#define MAX3107_PLLCFG_PREDIV_MASK (0x003f) /* PLL predivision value */ +#define MAX3107_PLLCFG_PLLFACTOR_MASK (0x00c0) /* PLL multiplication factor */ + +/* Baud rate generator configuration register masks and bits */ +#define MAX3107_BRGCFG_FRACT_MASK (0x000f) /* Fractional portion of + * Baud rate generator divisor + */ +#define MAX3107_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */ +#define MAX3107_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */ +#define MAX3107_BRGCFG_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_BRGCFG_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* Clock source register bits */ +#define MAX3107_CLKSRC_INTOSC_BIT (1 << 0) /* Internal osc enable */ +#define MAX3107_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */ +#define MAX3107_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */ +#define MAX3107_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */ +#define MAX3107_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */ +#define MAX3107_CLKSRC_UNDEF5_BIT (1 << 5) /* Undefined/not used */ +#define MAX3107_CLKSRC_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */ + + +/* HW definitions */ +#define MAX3107_RX_FIFO_SIZE 128 +#define MAX3107_TX_FIFO_SIZE 128 +#define MAX3107_REVID1 0x00a0 +#define MAX3107_REVID2 0x00a1 + + +/* Baud rate generator configuration values for external clock 13MHz */ +#define MAX3107_BRG13_B300 (0x0A9400 | 0x05) +#define MAX3107_BRG13_B600 (0x054A00 | 0x03) +#define MAX3107_BRG13_B1200 (0x02A500 | 0x01) +#define MAX3107_BRG13_B2400 (0x015200 | 0x09) +#define MAX3107_BRG13_B4800 (0x00A900 | 0x04) +#define MAX3107_BRG13_B9600 (0x005400 | 0x0A) +#define MAX3107_BRG13_B19200 (0x002A00 | 0x05) +#define MAX3107_BRG13_B38400 (0x001500 | 0x03) +#define MAX3107_BRG13_B57600 (0x000E00 | 0x02) +#define MAX3107_BRG13_B115200 (0x000700 | 0x01) +#define MAX3107_BRG13_B230400 (0x000300 | 0x08) +#define MAX3107_BRG13_B460800 (0x000100 | 0x0c) +#define MAX3107_BRG13_B921600 (0x000100 | 0x1c) + +/* Baud rate generator configuration values for external clock 26MHz */ +#define MAX3107_BRG26_B300 (0x152800 | 0x0A) +#define MAX3107_BRG26_B600 (0x0A9400 | 0x05) +#define MAX3107_BRG26_B1200 (0x054A00 | 0x03) +#define MAX3107_BRG26_B2400 (0x02A500 | 0x01) +#define MAX3107_BRG26_B4800 (0x015200 | 0x09) +#define MAX3107_BRG26_B9600 (0x00A900 | 0x04) +#define MAX3107_BRG26_B19200 (0x005400 | 0x0A) +#define MAX3107_BRG26_B38400 (0x002A00 | 0x05) +#define MAX3107_BRG26_B57600 (0x001C00 | 0x03) +#define MAX3107_BRG26_B115200 (0x000E00 | 0x02) +#define MAX3107_BRG26_B230400 (0x000700 | 0x01) +#define MAX3107_BRG26_B460800 (0x000300 | 0x08) +#define MAX3107_BRG26_B921600 (0x000100 | 0x0C) + +/* Baud rate generator configuration values for internal clock */ +#define MAX3107_BRG13_IB300 (0x008000 | 0x00) +#define MAX3107_BRG13_IB600 (0x004000 | 0x00) +#define MAX3107_BRG13_IB1200 (0x002000 | 0x00) +#define MAX3107_BRG13_IB2400 (0x001000 | 0x00) +#define MAX3107_BRG13_IB4800 (0x000800 | 0x00) +#define MAX3107_BRG13_IB9600 (0x000400 | 0x00) +#define MAX3107_BRG13_IB19200 (0x000200 | 0x00) +#define MAX3107_BRG13_IB38400 (0x000100 | 0x00) +#define MAX3107_BRG13_IB57600 (0x000000 | 0x0B) +#define MAX3107_BRG13_IB115200 (0x000000 | 0x05) +#define MAX3107_BRG13_IB230400 (0x000000 | 0x03) +#define MAX3107_BRG13_IB460800 (0x000000 | 0x00) +#define MAX3107_BRG13_IB921600 (0x000000 | 0x00) + + +struct baud_table { + int baud; + u32 new_brg; +}; + +struct max3107_port { + /* UART port structure */ + struct uart_port port; + + /* SPI device structure */ + struct spi_device *spi; + +#if defined(CONFIG_GPIOLIB) + /* GPIO chip stucture */ + struct gpio_chip chip; +#endif + + /* Workqueue that does all the magic */ + struct workqueue_struct *workqueue; + struct work_struct work; + + /* Lock for shared data */ + spinlock_t data_lock; + + /* Device configuration */ + int ext_clk; /* 1 if external clock used */ + int loopback; /* Current loopback mode state */ + int baud; /* Current baud rate */ + + /* State flags */ + int suspended; /* Indicates suspend mode */ + int tx_fifo_empty; /* Flag for TX FIFO state */ + int rx_enabled; /* Flag for receiver state */ + int tx_enabled; /* Flag for transmitter state */ + + u16 irqen_reg; /* Current IRQ enable register value */ + /* Shared data */ + u16 mode1_reg; /* Current mode1 register value*/ + int mode1_commit; /* Flag for setting new mode1 register value */ + u16 lcr_reg; /* Current LCR register value */ + int lcr_commit; /* Flag for setting new LCR register value */ + u32 brg_cfg; /* Current Baud rate generator config */ + int brg_commit; /* Flag for setting new baud rate generator + * config + */ + struct baud_table *baud_tbl; + int handle_irq; /* Indicates that IRQ should be handled */ + + /* Rx buffer and str*/ + u16 *rxbuf; + u8 *rxstr; + /* Tx buffer*/ + u16 *txbuf; + + struct max3107_plat *pdata; /* Platform data */ +}; + +/* Platform data structure */ +struct max3107_plat { + /* Loopback mode enable */ + int loopback; + /* External clock enable */ + int ext_clk; + /* Called during the register initialisation */ + void (*init)(struct max3107_port *s); + /* Called when the port is found and configured */ + int (*configure)(struct max3107_port *s); + /* HW suspend function */ + void (*hw_suspend) (struct max3107_port *s, int suspend); + /* Polling mode enable */ + int polled_mode; + /* Polling period if polling mode enabled */ + int poll_time; +}; + +extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len); +extern void max3107_hw_susp(struct max3107_port *s, int suspend); +extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata); +extern int max3107_remove(struct spi_device *spi); +extern int max3107_suspend(struct spi_device *spi, pm_message_t state); +extern int max3107_resume(struct spi_device *spi); + +#endif /* _LINUX_SERIAL_MAX3107_H */ |