diff options
Diffstat (limited to 'drivers/serial/sunsu.c')
| -rw-r--r-- | drivers/serial/sunsu.c | 14 |
1 files changed, 7 insertions, 7 deletions
diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c index 9a3665b34d9..bc67442c6b4 100644 --- a/drivers/serial/sunsu.c +++ b/drivers/serial/sunsu.c @@ -669,7 +669,7 @@ static int sunsu_startup(struct uart_port *port) * if it is, then bail out, because there's likely no UART * here. */ - if (!(up->port.flags & ASYNC_BUGGY_UART) && + if (!(up->port.flags & UPF_BUGGY_UART) && (serial_inp(up, UART_LSR) == 0xff)) { printk("ttyS%d: LSR safety check engaged!\n", up->port.line); return -ENODEV; @@ -707,7 +707,7 @@ static int sunsu_startup(struct uart_port *port) up->ier = UART_IER_RLSI | UART_IER_RDI; serial_outp(up, UART_IER, up->ier); - if (up->port.flags & ASYNC_FOURPORT) { + if (up->port.flags & UPF_FOURPORT) { unsigned int icp; /* * Enable interrupts on the AST Fourport board @@ -740,7 +740,7 @@ static void sunsu_shutdown(struct uart_port *port) serial_outp(up, UART_IER, 0); spin_lock_irqsave(&up->port.lock, flags); - if (up->port.flags & ASYNC_FOURPORT) { + if (up->port.flags & UPF_FOURPORT) { /* reset interrupts on the AST Fourport board */ inb((up->port.iobase & 0xfe0) | 0x1f); up->port.mctrl |= TIOCM_OUT1; @@ -1132,7 +1132,7 @@ ebus_done: spin_lock_irqsave(&up->port.lock, flags); - if (!(up->port.flags & ASYNC_BUGGY_UART)) { + if (!(up->port.flags & UPF_BUGGY_UART)) { /* * Do a simple existence test first; if we fail this, there's * no point trying anything else. @@ -1170,7 +1170,7 @@ ebus_done: * manufacturer would be stupid enough to design a board * that conflicts with COM 1-4 --- we hope! */ - if (!(up->port.flags & ASYNC_SKIP_TEST)) { + if (!(up->port.flags & UPF_SKIP_TEST)) { serial_outp(up, UART_MCR, UART_MCR_LOOP | 0x0A); status1 = serial_inp(up, UART_MSR) & 0xF0; serial_outp(up, UART_MCR, save_mcr); @@ -1371,7 +1371,7 @@ static __inline__ void wait_for_xmitr(struct uart_sunsu_port *up) } while ((status & BOTH_EMPTY) != BOTH_EMPTY); /* Wait up to 1s for flow control if necessary */ - if (up->port.flags & ASYNC_CONS_FLOW) { + if (up->port.flags & UPF_CONS_FLOW) { tmout = 1000000; while (--tmout && ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0)) @@ -1513,7 +1513,7 @@ static int __init sunsu_serial_init(void) up->su_type == SU_PORT_KBD) continue; - up->port.flags |= ASYNC_BOOT_AUTOCONF; + up->port.flags |= UPF_BOOT_AUTOCONF; up->port.type = PORT_UNKNOWN; up->port.uartclk = (SU_BASE_BAUD * 16); |