diff options
Diffstat (limited to 'drivers/serial/sunzilog.h')
| -rw-r--r-- | drivers/serial/sunzilog.h | 289 |
1 files changed, 0 insertions, 289 deletions
diff --git a/drivers/serial/sunzilog.h b/drivers/serial/sunzilog.h deleted file mode 100644 index 5dec7b47cc3..00000000000 --- a/drivers/serial/sunzilog.h +++ /dev/null @@ -1,289 +0,0 @@ -#ifndef _SUNZILOG_H -#define _SUNZILOG_H - -struct zilog_channel { - volatile unsigned char control; - volatile unsigned char __pad1; - volatile unsigned char data; - volatile unsigned char __pad2; -}; - -struct zilog_layout { - struct zilog_channel channelB; - struct zilog_channel channelA; -}; - -#define NUM_ZSREGS 17 -#define R7p 16 /* Written as R7 with P15 bit 0 set */ - -/* Conversion routines to/from brg time constants from/to bits - * per second. - */ -#define BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2)) -#define BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2) - -/* The Zilog register set */ - -#define FLAG 0x7e - -/* Write Register 0 */ -#define R0 0 /* Register selects */ -#define R1 1 -#define R2 2 -#define R3 3 -#define R4 4 -#define R5 5 -#define R6 6 -#define R7 7 -#define R8 8 -#define R9 9 -#define R10 10 -#define R11 11 -#define R12 12 -#define R13 13 -#define R14 14 -#define R15 15 - -#define NULLCODE 0 /* Null Code */ -#define POINT_HIGH 0x8 /* Select upper half of registers */ -#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */ -#define SEND_ABORT 0x18 /* HDLC Abort */ -#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */ -#define RES_Tx_P 0x28 /* Reset TxINT Pending */ -#define ERR_RES 0x30 /* Error Reset */ -#define RES_H_IUS 0x38 /* Reset highest IUS */ - -#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */ -#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */ -#define RES_EOM_L 0xC0 /* Reset EOM latch */ - -/* Write Register 1 */ - -#define EXT_INT_ENAB 0x1 /* Ext Int Enable */ -#define TxINT_ENAB 0x2 /* Tx Int Enable */ -#define PAR_SPEC 0x4 /* Parity is special condition */ - -#define RxINT_DISAB 0 /* Rx Int Disable */ -#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */ -#define INT_ALL_Rx 0x10 /* Int on all Rx Characters or error */ -#define INT_ERR_Rx 0x18 /* Int on error only */ -#define RxINT_MASK 0x18 - -#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */ -#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */ -#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */ - -/* Write Register #2 (Interrupt Vector) */ - -/* Write Register 3 */ - -#define RxENAB 0x1 /* Rx Enable */ -#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */ -#define ADD_SM 0x4 /* Address Search Mode (SDLC) */ -#define RxCRC_ENAB 0x8 /* Rx CRC Enable */ -#define ENT_HM 0x10 /* Enter Hunt Mode */ -#define AUTO_ENAB 0x20 /* Auto Enables */ -#define Rx5 0x0 /* Rx 5 Bits/Character */ -#define Rx7 0x40 /* Rx 7 Bits/Character */ -#define Rx6 0x80 /* Rx 6 Bits/Character */ -#define Rx8 0xc0 /* Rx 8 Bits/Character */ -#define RxN_MASK 0xc0 - -/* Write Register 4 */ - -#define PAR_ENAB 0x1 /* Parity Enable */ -#define PAR_EVEN 0x2 /* Parity Even/Odd* */ - -#define SYNC_ENAB 0 /* Sync Modes Enable */ -#define SB1 0x4 /* 1 stop bit/char */ -#define SB15 0x8 /* 1.5 stop bits/char */ -#define SB2 0xc /* 2 stop bits/char */ - -#define MONSYNC 0 /* 8 Bit Sync character */ -#define BISYNC 0x10 /* 16 bit sync character */ -#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */ -#define EXTSYNC 0x30 /* External Sync Mode */ - -#define X1CLK 0x0 /* x1 clock mode */ -#define X16CLK 0x40 /* x16 clock mode */ -#define X32CLK 0x80 /* x32 clock mode */ -#define X64CLK 0xC0 /* x64 clock mode */ -#define XCLK_MASK 0xC0 - -/* Write Register 5 */ - -#define TxCRC_ENAB 0x1 /* Tx CRC Enable */ -#define RTS 0x2 /* RTS */ -#define SDLC_CRC 0x4 /* SDLC/CRC-16 */ -#define TxENAB 0x8 /* Tx Enable */ -#define SND_BRK 0x10 /* Send Break */ -#define Tx5 0x0 /* Tx 5 bits (or less)/character */ -#define Tx7 0x20 /* Tx 7 bits/character */ -#define Tx6 0x40 /* Tx 6 bits/character */ -#define Tx8 0x60 /* Tx 8 bits/character */ -#define TxN_MASK 0x60 -#define DTR 0x80 /* DTR */ - -/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ - -/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ - -/* Write Register 7' (ESCC Only) */ -#define AUTO_TxFLAG 1 /* Automatic Tx SDLC Flag */ -#define AUTO_EOM_RST 2 /* Automatic EOM Reset */ -#define AUTOnRTS 4 /* Automatic /RTS pin deactivation */ -#define RxFIFO_LVL 8 /* Receive FIFO interrupt level */ -#define nDTRnREQ 0x10 /* /DTR/REQ timing */ -#define TxFIFO_LVL 0x20 /* Transmit FIFO interrupt level */ -#define EXT_RD_EN 0x40 /* Extended read register enable */ - -/* Write Register 8 (transmit buffer) */ - -/* Write Register 9 (Master interrupt control) */ -#define VIS 1 /* Vector Includes Status */ -#define NV 2 /* No Vector */ -#define DLC 4 /* Disable Lower Chain */ -#define MIE 8 /* Master Interrupt Enable */ -#define STATHI 0x10 /* Status high */ -#define SWIACK 0x20 /* Software Interrupt Ack (not on NMOS) */ -#define NORESET 0 /* No reset on write to R9 */ -#define CHRB 0x40 /* Reset channel B */ -#define CHRA 0x80 /* Reset channel A */ -#define FHWRES 0xc0 /* Force hardware reset */ - -/* Write Register 10 (misc control bits) */ -#define BIT6 1 /* 6 bit/8bit sync */ -#define LOOPMODE 2 /* SDLC Loop mode */ -#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */ -#define MARKIDLE 8 /* Mark/flag on idle */ -#define GAOP 0x10 /* Go active on poll */ -#define NRZ 0 /* NRZ mode */ -#define NRZI 0x20 /* NRZI mode */ -#define FM1 0x40 /* FM1 (transition = 1) */ -#define FM0 0x60 /* FM0 (transition = 0) */ -#define CRCPS 0x80 /* CRC Preset I/O */ - -/* Write Register 11 (Clock Mode control) */ -#define TRxCXT 0 /* TRxC = Xtal output */ -#define TRxCTC 1 /* TRxC = Transmit clock */ -#define TRxCBR 2 /* TRxC = BR Generator Output */ -#define TRxCDP 3 /* TRxC = DPLL output */ -#define TRxCOI 4 /* TRxC O/I */ -#define TCRTxCP 0 /* Transmit clock = RTxC pin */ -#define TCTRxCP 8 /* Transmit clock = TRxC pin */ -#define TCBR 0x10 /* Transmit clock = BR Generator output */ -#define TCDPLL 0x18 /* Transmit clock = DPLL output */ -#define RCRTxCP 0 /* Receive clock = RTxC pin */ -#define RCTRxCP 0x20 /* Receive clock = TRxC pin */ -#define RCBR 0x40 /* Receive clock = BR Generator output */ -#define RCDPLL 0x60 /* Receive clock = DPLL output */ -#define RTxCX 0x80 /* RTxC Xtal/No Xtal */ - -/* Write Register 12 (lower byte of baud rate generator time constant) */ - -/* Write Register 13 (upper byte of baud rate generator time constant) */ - -/* Write Register 14 (Misc control bits) */ -#define BRENAB 1 /* Baud rate generator enable */ -#define BRSRC 2 /* Baud rate generator source */ -#define DTRREQ 4 /* DTR/Request function */ -#define AUTOECHO 8 /* Auto Echo */ -#define LOOPBAK 0x10 /* Local loopback */ -#define SEARCH 0x20 /* Enter search mode */ -#define RMC 0x40 /* Reset missing clock */ -#define DISDPLL 0x60 /* Disable DPLL */ -#define SSBR 0x80 /* Set DPLL source = BR generator */ -#define SSRTxC 0xa0 /* Set DPLL source = RTxC */ -#define SFMM 0xc0 /* Set FM mode */ -#define SNRZI 0xe0 /* Set NRZI mode */ - -/* Write Register 15 (external/status interrupt control) */ -#define WR7pEN 1 /* WR7' Enable (ESCC only) */ -#define ZCIE 2 /* Zero count IE */ -#define FIFOEN 4 /* FIFO Enable (ESCC only) */ -#define DCDIE 8 /* DCD IE */ -#define SYNCIE 0x10 /* Sync/hunt IE */ -#define CTSIE 0x20 /* CTS IE */ -#define TxUIE 0x40 /* Tx Underrun/EOM IE */ -#define BRKIE 0x80 /* Break/Abort IE */ - - -/* Read Register 0 */ -#define Rx_CH_AV 0x1 /* Rx Character Available */ -#define ZCOUNT 0x2 /* Zero count */ -#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */ -#define DCD 0x8 /* DCD */ -#define SYNC 0x10 /* Sync/hunt */ -#define CTS 0x20 /* CTS */ -#define TxEOM 0x40 /* Tx underrun */ -#define BRK_ABRT 0x80 /* Break/Abort */ - -/* Read Register 1 */ -#define ALL_SNT 0x1 /* All sent */ -/* Residue Data for 8 Rx bits/char programmed */ -#define RES3 0x8 /* 0/3 */ -#define RES4 0x4 /* 0/4 */ -#define RES5 0xc /* 0/5 */ -#define RES6 0x2 /* 0/6 */ -#define RES7 0xa /* 0/7 */ -#define RES8 0x6 /* 0/8 */ -#define RES18 0xe /* 1/8 */ -#define RES28 0x0 /* 2/8 */ -/* Special Rx Condition Interrupts */ -#define PAR_ERR 0x10 /* Parity error */ -#define Rx_OVR 0x20 /* Rx Overrun Error */ -#define CRC_ERR 0x40 /* CRC/Framing Error */ -#define END_FR 0x80 /* End of Frame (SDLC) */ - -/* Read Register 2 (channel b only) - Interrupt vector */ -#define CHB_Tx_EMPTY 0x00 -#define CHB_EXT_STAT 0x02 -#define CHB_Rx_AVAIL 0x04 -#define CHB_SPECIAL 0x06 -#define CHA_Tx_EMPTY 0x08 -#define CHA_EXT_STAT 0x0a -#define CHA_Rx_AVAIL 0x0c -#define CHA_SPECIAL 0x0e -#define STATUS_MASK 0x0e - -/* Read Register 3 (interrupt pending register) ch a only */ -#define CHBEXT 0x1 /* Channel B Ext/Stat IP */ -#define CHBTxIP 0x2 /* Channel B Tx IP */ -#define CHBRxIP 0x4 /* Channel B Rx IP */ -#define CHAEXT 0x8 /* Channel A Ext/Stat IP */ -#define CHATxIP 0x10 /* Channel A Tx IP */ -#define CHARxIP 0x20 /* Channel A Rx IP */ - -/* Read Register 6 (LSB frame byte count [Not on NMOS]) */ - -/* Read Register 7 (MSB frame byte count and FIFO status [Not on NMOS]) */ - -/* Read Register 8 (receive data register) */ - -/* Read Register 10 (misc status bits) */ -#define ONLOOP 2 /* On loop */ -#define LOOPSEND 0x10 /* Loop sending */ -#define CLK2MIS 0x40 /* Two clocks missing */ -#define CLK1MIS 0x80 /* One clock missing */ - -/* Read Register 12 (lower byte of baud rate generator constant) */ - -/* Read Register 13 (upper byte of baud rate generator constant) */ - -/* Read Register 15 (value of WR 15) */ - -/* Misc macros */ -#define ZS_CLEARERR(channel) do { sbus_writeb(ERR_RES, &channel->control); \ - udelay(5); } while(0) - -#define ZS_CLEARSTAT(channel) do { sbus_writeb(RES_EXT_INT, &channel->control); \ - udelay(5); } while(0) - -#define ZS_CLEARFIFO(channel) do { sbus_readb(&channel->data); \ - udelay(2); \ - sbus_readb(&channel->data); \ - udelay(2); \ - sbus_readb(&channel->data); \ - udelay(2); } while(0) - -#endif /* _SUNZILOG_H */ |