summaryrefslogtreecommitdiffstats
path: root/drivers/serial
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial')
-rw-r--r--drivers/serial/8250.c22
-rw-r--r--drivers/serial/8250_gsc.c4
-rw-r--r--drivers/serial/8250_pci.c5
-rw-r--r--drivers/serial/Kconfig8
-rw-r--r--drivers/serial/Makefile1
-rw-r--r--drivers/serial/amba-pl010.c2
-rw-r--r--drivers/serial/amba-pl011.c2
-rw-r--r--drivers/serial/bfin_5xx.c83
-rw-r--r--drivers/serial/bfin_sport_uart.c58
-rw-r--r--drivers/serial/crisv10.c173
-rw-r--r--drivers/serial/icom.c22
-rw-r--r--drivers/serial/imx.c296
-rw-r--r--drivers/serial/jsm/jsm.h3
-rw-r--r--drivers/serial/jsm/jsm_driver.c1
-rw-r--r--drivers/serial/jsm/jsm_tty.c14
-rw-r--r--drivers/serial/mpc52xx_uart.c2
-rw-r--r--drivers/serial/nwpserial.c4
-rw-r--r--drivers/serial/s3c6400.c1
-rw-r--r--drivers/serial/samsung.c61
-rw-r--r--drivers/serial/samsung.h4
-rw-r--r--drivers/serial/sh-sci.c388
-rw-r--r--drivers/serial/sh-sci.h42
-rw-r--r--drivers/serial/timbuart.c526
-rw-r--r--drivers/serial/timbuart.h58
24 files changed, 1370 insertions, 410 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index b4b39811b44..fb867a9f55e 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -137,6 +137,7 @@ struct uart_8250_port {
unsigned char mcr;
unsigned char mcr_mask; /* mask of user bits */
unsigned char mcr_force; /* mask of forced bits */
+ unsigned char cur_iotype; /* Running I/O type */
/*
* Some bits in registers are cleared on a read, so they must
@@ -286,6 +287,13 @@ static const struct serial8250_config uart_config[] = {
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO,
},
+ [PORT_AR7] = {
+ .name = "AR7",
+ .fifo_size = 16,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00,
+ .flags = UART_CAP_FIFO | UART_CAP_AFE,
+ },
};
#if defined (CONFIG_SERIAL_8250_AU1X00)
@@ -471,6 +479,7 @@ static void io_serial_out(struct uart_port *p, int offset, int value)
static void set_io_from_upio(struct uart_port *p)
{
+ struct uart_8250_port *up = (struct uart_8250_port *)p;
switch (p->iotype) {
case UPIO_HUB6:
p->serial_in = hub6_serial_in;
@@ -509,6 +518,8 @@ static void set_io_from_upio(struct uart_port *p)
p->serial_out = io_serial_out;
break;
}
+ /* Remember loaded iotype */
+ up->cur_iotype = p->iotype;
}
static void
@@ -1937,6 +1948,9 @@ static int serial8250_startup(struct uart_port *port)
up->capabilities = uart_config[up->port.type].flags;
up->mcr = 0;
+ if (up->port.iotype != up->cur_iotype)
+ set_io_from_upio(port);
+
if (up->port.type == PORT_16C950) {
/* Wake up and initialize UART */
up->acr = 0;
@@ -2563,6 +2577,9 @@ static void serial8250_config_port(struct uart_port *port, int flags)
if (ret < 0)
probeflags &= ~PROBE_RSA;
+ if (up->port.iotype != up->cur_iotype)
+ set_io_from_upio(port);
+
if (flags & UART_CONFIG_TYPE)
autoconfig(up, probeflags);
if (up->port.type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ)
@@ -2671,6 +2688,11 @@ serial8250_register_ports(struct uart_driver *drv, struct device *dev)
{
int i;
+ for (i = 0; i < nr_uarts; i++) {
+ struct uart_8250_port *up = &serial8250_ports[i];
+ up->cur_iotype = 0xFF;
+ }
+
serial8250_isa_init_ports();
for (i = 0; i < nr_uarts; i++) {
diff --git a/drivers/serial/8250_gsc.c b/drivers/serial/8250_gsc.c
index 418b4fe9a0a..33149d982e8 100644
--- a/drivers/serial/8250_gsc.c
+++ b/drivers/serial/8250_gsc.c
@@ -39,9 +39,9 @@ static int __init serial_init_chip(struct parisc_device *dev)
*/
if (parisc_parent(dev)->id.hw_type != HPHW_IOA)
printk(KERN_INFO
- "Serial: device 0x%lx not configured.\n"
+ "Serial: device 0x%llx not configured.\n"
"Enable support for Wax, Lasi, Asp or Dino.\n",
- dev->hpa.start);
+ (unsigned long long)dev->hpa.start);
return -ENODEV;
}
diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c
index 7ddff3f5508..e371a9c1534 100644
--- a/drivers/serial/8250_pci.c
+++ b/drivers/serial/8250_pci.c
@@ -771,8 +771,6 @@ static int pci_netmos_init(struct pci_dev *dev)
}
/*
- * ITE support by Niels de Vos <niels.devos@wincor-nixdorf.com>
- *
* These chips are available with optionally one parallel port and up to
* two serial ports. Unfortunately they all have the same product id.
*
@@ -2778,6 +2776,9 @@ static struct pci_device_id serial_pci_tbl[] = {
{ PCI_VENDOR_ID_OXSEMI, 0x950a,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_2_1130000 },
+ { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_C950,
+ PCI_VENDOR_ID_OXSEMI, PCI_SUBDEVICE_ID_OXSEMI_C950, 0, 0,
+ pbn_b0_1_921600 },
{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954,
PCI_ANY_ID, PCI_ANY_ID, 0, 0,
pbn_b0_4_115200 },
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index 343e3a35b6a..641e800ed69 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -833,6 +833,7 @@ config SERIAL_IMX
bool "IMX serial port support"
depends on ARM && (ARCH_IMX || ARCH_MXC)
select SERIAL_CORE
+ select RATIONAL
help
If you have a machine based on a Motorola IMX CPU you
can enable its onboard serial port by enabling this option.
@@ -1433,4 +1434,11 @@ config SPORT_BAUD_RATE
default 19200 if (SERIAL_SPORT_BAUD_RATE_19200)
default 9600 if (SERIAL_SPORT_BAUD_RATE_9600)
+config SERIAL_TIMBERDALE
+ tristate "Support for timberdale UART"
+ depends on MFD_TIMBERDALE
+ select SERIAL_CORE
+ ---help---
+ Add support for UART controller on timberdale.
+
endmenu
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index d438eb2a73d..45a8658f54d 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -77,3 +77,4 @@ obj-$(CONFIG_SERIAL_OF_PLATFORM_NWPSERIAL) += nwpserial.o
obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
+obj-$(CONFIG_SERIAL_TIMBERDALE) += timbuart.o
diff --git a/drivers/serial/amba-pl010.c b/drivers/serial/amba-pl010.c
index e3a5ad5ef1d..cdc049d4350 100644
--- a/drivers/serial/amba-pl010.c
+++ b/drivers/serial/amba-pl010.c
@@ -665,7 +665,7 @@ static struct uart_driver amba_reg = {
.cons = AMBA_CONSOLE,
};
-static int pl010_probe(struct amba_device *dev, void *id)
+static int pl010_probe(struct amba_device *dev, struct amba_id *id)
{
struct uart_amba_port *uap;
void __iomem *base;
diff --git a/drivers/serial/amba-pl011.c b/drivers/serial/amba-pl011.c
index 8b2b9700f3e..88fdac51b6c 100644
--- a/drivers/serial/amba-pl011.c
+++ b/drivers/serial/amba-pl011.c
@@ -729,7 +729,7 @@ static struct uart_driver amba_reg = {
.cons = AMBA_CONSOLE,
};
-static int pl011_probe(struct amba_device *dev, void *id)
+static int pl011_probe(struct amba_device *dev, struct amba_id *id)
{
struct uart_amba_port *uap;
void __iomem *base;
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
index 18ba812a4f8..e2f6b1bfac9 100644
--- a/drivers/serial/bfin_5xx.c
+++ b/drivers/serial/bfin_5xx.c
@@ -166,7 +166,7 @@ static void bfin_serial_start_tx(struct uart_port *port)
struct tty_struct *tty = uart->port.info->port.tty;
#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
- if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
uart->scts = 0;
uart_handle_cts_change(&uart->port, uart->scts);
}
@@ -330,6 +330,11 @@ static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
/* Clear TFI bit */
UART_PUT_LSR(uart, TFI);
#endif
+ /* Anomaly notes:
+ * 05000215 - we always clear ETBEI within last UART TX
+ * interrupt to end a string. It is always set
+ * when start a new tx.
+ */
UART_CLEAR_IER(uart, ETBEI);
return;
}
@@ -368,7 +373,7 @@ static irqreturn_t bfin_serial_tx_int(int irq, void *dev_id)
struct bfin_serial_port *uart = dev_id;
#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
- if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ if (uart->scts && !(bfin_serial_get_mctrl(&uart->port) & TIOCM_CTS)) {
uart->scts = 0;
uart_handle_cts_change(&uart->port, uart->scts);
}
@@ -415,6 +420,7 @@ static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
set_dma_x_modify(uart->tx_dma_channel, 1);
+ SSYNC();
enable_dma(uart->tx_dma_channel);
UART_SET_IER(uart, ETBEI);
@@ -473,27 +479,41 @@ static void bfin_serial_dma_rx_chars(struct bfin_serial_port *uart)
void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
{
int x_pos, pos;
- unsigned long flags;
-
- spin_lock_irqsave(&uart->port.lock, flags);
+ dma_disable_irq(uart->rx_dma_channel);
+ spin_lock_bh(&uart->port.lock);
+
+ /* 2D DMA RX buffer ring is used. Because curr_y_count and
+ * curr_x_count can't be read as an atomic operation,
+ * curr_y_count should be read before curr_x_count. When
+ * curr_x_count is read, curr_y_count may already indicate
+ * next buffer line. But, the position calculated here is
+ * still indicate the old line. The wrong position data may
+ * be smaller than current buffer tail, which cause garbages
+ * are received if it is not prohibit.
+ */
uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
- if (uart->rx_dma_nrows == DMA_RX_YCOUNT)
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
uart->rx_dma_nrows = 0;
x_pos = DMA_RX_XCOUNT - x_pos;
if (x_pos == DMA_RX_XCOUNT)
x_pos = 0;
pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
- if (pos != uart->rx_dma_buf.tail) {
+ /* Ignore receiving data if new position is in the same line of
+ * current buffer tail and small.
+ */
+ if (pos > uart->rx_dma_buf.tail ||
+ uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
uart->rx_dma_buf.head = pos;
bfin_serial_dma_rx_chars(uart);
uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
}
- spin_unlock_irqrestore(&uart->port.lock, flags);
+ spin_unlock_bh(&uart->port.lock);
+ dma_enable_irq(uart->rx_dma_channel);
mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES);
}
@@ -504,7 +524,7 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
struct circ_buf *xmit = &uart->port.info->xmit;
#ifdef CONFIG_SERIAL_BFIN_HARD_CTSRTS
- if (uart->scts && (!bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
+ if (uart->scts && !(bfin_serial_get_mctrl(&uart->port)&TIOCM_CTS)) {
uart->scts = 0;
uart_handle_cts_change(&uart->port, uart->scts);
}
@@ -514,6 +534,11 @@ static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
disable_dma(uart->tx_dma_channel);
clear_dma_irqstat(uart->tx_dma_channel);
+ /* Anomaly notes:
+ * 05000215 - we always clear ETBEI within last UART TX
+ * interrupt to end a string. It is always set
+ * when start a new tx.
+ */
UART_CLEAR_IER(uart, ETBEI);
xmit->tail = (xmit->tail + uart->tx_count) & (UART_XMIT_SIZE - 1);
uart->port.icount.tx += uart->tx_count;
@@ -532,11 +557,26 @@ static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
{
struct bfin_serial_port *uart = dev_id;
unsigned short irqstat;
+ int x_pos, pos;
spin_lock(&uart->port.lock);
irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
clear_dma_irqstat(uart->rx_dma_channel);
- bfin_serial_dma_rx_chars(uart);
+
+ uart->rx_dma_nrows = get_dma_curr_ycount(uart->rx_dma_channel);
+ x_pos = get_dma_curr_xcount(uart->rx_dma_channel);
+ uart->rx_dma_nrows = DMA_RX_YCOUNT - uart->rx_dma_nrows;
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT || x_pos == 0)
+ uart->rx_dma_nrows = 0;
+
+ pos = uart->rx_dma_nrows * DMA_RX_XCOUNT;
+ if (pos > uart->rx_dma_buf.tail ||
+ uart->rx_dma_nrows < (uart->rx_dma_buf.tail/DMA_RX_XCOUNT)) {
+ uart->rx_dma_buf.head = pos;
+ bfin_serial_dma_rx_chars(uart);
+ uart->rx_dma_buf.tail = uart->rx_dma_buf.head;
+ }
+
spin_unlock(&uart->port.lock);
return IRQ_HANDLED;
@@ -789,8 +829,16 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
__func__);
}
- if (termios->c_cflag & CSTOPB)
- lcr |= STB;
+ /* Anomaly notes:
+ * 05000231 - STOP bit is always set to 1 whatever the user is set.
+ */
+ if (termios->c_cflag & CSTOPB) {
+ if (ANOMALY_05000231)
+ printk(KERN_WARNING "STOP bits other than 1 is not "
+ "supported in case of anomaly 05000231.\n");
+ else
+ lcr |= STB;
+ }
if (termios->c_cflag & PARENB)
lcr |= PEN;
if (!(termios->c_cflag & PARODD))
@@ -940,6 +988,10 @@ static void bfin_serial_reset_irda(struct uart_port *port)
}
#ifdef CONFIG_CONSOLE_POLL
+/* Anomaly notes:
+ * 05000099 - Because we only use THRE in poll_put and DR in poll_get,
+ * losing other bits of UART_LSR is not a problem here.
+ */
static void bfin_serial_poll_put_char(struct uart_port *port, unsigned char chr)
{
struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
@@ -1245,12 +1297,17 @@ static __init void early_serial_write(struct console *con, const char *s,
}
}
+/*
+ * This should have a .setup or .early_setup in it, but then things get called
+ * without the command line options, and the baud rate gets messed up - so
+ * don't let the common infrastructure play with things. (see calls to setup
+ * & earlysetup in ./kernel/printk.c:register_console()
+ */
static struct __initdata console bfin_early_serial_console = {
.name = "early_BFuart",
.write = early_serial_write,
.device = uart_console_device,
.flags = CON_PRINTBUFFER,
- .setup = bfin_serial_console_setup,
.index = -1,
.data = &bfin_serial_reg,
};
diff --git a/drivers/serial/bfin_sport_uart.c b/drivers/serial/bfin_sport_uart.c
index 529c0ff7952..34b4ae0fe76 100644
--- a/drivers/serial/bfin_sport_uart.c
+++ b/drivers/serial/bfin_sport_uart.c
@@ -101,15 +101,16 @@ static inline void tx_one_byte(struct sport_uart_port *up, unsigned int value)
{
pr_debug("%s value:%x\n", __func__, value);
/* Place a Start and Stop bit */
- __asm__ volatile (
- "R2 = b#01111111100;\n\t"
- "R3 = b#10000000001;\n\t"
- "%0 <<= 2;\n\t"
- "%0 = %0 & R2;\n\t"
- "%0 = %0 | R3;\n\t"
- :"=r"(value)
- :"0"(value)
- :"R2", "R3");
+ __asm__ __volatile__ (
+ "R2 = b#01111111100;"
+ "R3 = b#10000000001;"
+ "%0 <<= 2;"
+ "%0 = %0 & R2;"
+ "%0 = %0 | R3;"
+ : "=d"(value)
+ : "d"(value)
+ : "ASTAT", "R2", "R3"
+ );
pr_debug("%s value:%x\n", __func__, value);
SPORT_PUT_TX(up, value);
@@ -118,27 +119,30 @@ static inline void tx_one_byte(struct sport_uart_port *up, unsigned int value)
static inline unsigned int rx_one_byte(struct sport_uart_port *up)
{
unsigned int value, extract;
+ u32 tmp_mask1, tmp_mask2, tmp_shift, tmp;
value = SPORT_GET_RX32(up);
pr_debug("%s value:%x\n", __func__, value);
/* Extract 8 bits data */
- __asm__ volatile (
- "R5 = 0;\n\t"
- "P0 = 8;\n\t"
- "R1 = 0x1801(Z);\n\t"
- "R3 = 0x0300(Z);\n\t"
- "R4 = 0;\n\t"
- "LSETUP(loop_s, loop_e) LC0 = P0;\nloop_s:\t"
- "R2 = extract(%1, R1.L)(Z);\n\t"
- "R2 <<= R4;\n\t"
- "R5 = R5 | R2;\n\t"
- "R1 = R1 - R3;\nloop_e:\t"
- "R4 += 1;\n\t"
- "%0 = R5;\n\t"
- :"=r"(extract)
- :"r"(value)
- :"P0", "R1", "R2","R3","R4", "R5");
+ __asm__ __volatile__ (
+ "%[extr] = 0;"
+ "%[mask1] = 0x1801(Z);"
+ "%[mask2] = 0x0300(Z);"
+ "%[shift] = 0;"
+ "LSETUP(.Lloop_s, .Lloop_e) LC0 = %[lc];"
+ ".Lloop_s:"
+ "%[tmp] = extract(%[val], %[mask1].L)(Z);"
+ "%[tmp] <<= %[shift];"
+ "%[extr] = %[extr] | %[tmp];"
+ "%[mask1] = %[mask1] - %[mask2];"
+ ".Lloop_e:"
+ "%[shift] += 1;"
+ : [val]"=d"(value), [extr]"=d"(extract), [shift]"=d"(tmp_shift), [tmp]"=d"(tmp),
+ [mask1]"=d"(tmp_mask1), [mask2]"=d"(tmp_mask2)
+ : "d"(value), [lc]"a"(8)
+ : "ASTAT", "LB0", "LC0", "LT0"
+ );
pr_debug(" extract:%x\n", extract);
return extract;
@@ -149,7 +153,7 @@ static int sport_uart_setup(struct sport_uart_port *up, int sclk, int baud_rate)
int tclkdiv, tfsdiv, rclkdiv;
/* Set TCR1 and TCR2 */
- SPORT_PUT_TCR1(up, (LTFS | ITFS | TFSR | TLSBIT | ITCLK));
+ SPORT_PUT_TCR1(up, (LATFS | ITFS | TFSR | TLSBIT | ITCLK));
SPORT_PUT_TCR2(up, 10);
pr_debug("%s TCR1:%x, TCR2:%x\n", __func__, SPORT_GET_TCR1(up), SPORT_GET_TCR2(up));
@@ -419,7 +423,7 @@ static void sport_shutdown(struct uart_port *port)
}
static void sport_set_termios(struct uart_port *port,
- struct termios *termios, struct termios *old)
+ struct ktermios *termios, struct ktermios *old)
{
pr_debug("%s enter, c_cflag:%08x\n", __func__, termios->c_cflag);
uart_update_timeout(port, CS8 ,port->uartclk);
diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c
index 7ba7d70f04d..7be52fe288e 100644
--- a/drivers/serial/crisv10.c
+++ b/drivers/serial/crisv10.c
@@ -23,16 +23,18 @@ static char *serial_version = "$Revision: 1.25 $";
#include <linux/mm.h>
#include <linux/slab.h>
#include <linux/init.h>
-#include <asm/uaccess.h>
#include <linux/kernel.h>
#include <linux/mutex.h>
#include <linux/bitops.h>
+#include <linux/seq_file.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/uaccess.h>
+#include <linux/io.h>
-#include <asm/io.h>
#include <asm/irq.h>
#include <asm/dma.h>
#include <asm/system.h>
-#include <linux/delay.h>
#include <arch/svinto.h>
@@ -456,7 +458,6 @@ static struct e100_serial rs_table[] = {
#define NR_PORTS (sizeof(rs_table)/sizeof(struct e100_serial))
-static struct ktermios *serial_termios[NR_PORTS];
#ifdef CONFIG_ETRAX_SERIAL_FAST_TIMER
static struct fast_timer fast_timers[NR_PORTS];
#endif
@@ -4257,151 +4258,132 @@ rs_open(struct tty_struct *tty, struct file * filp)
return 0;
}
+#ifdef CONFIG_PROC_FS
/*
* /proc fs routines....
*/
-static int line_info(char *buf, struct e100_serial *info)
+static void seq_line_info(struct seq_file *m, struct e100_serial *info)
{
- char stat_buf[30];
- int ret;
unsigned long tmp;
- ret = sprintf(buf, "%d: uart:E100 port:%lX irq:%d",
- info->line, (unsigned long)info->ioport, info->irq);
+ seq_printf(m, "%d: uart:E100 port:%lX irq:%d",
+ info->line, (unsigned long)info->ioport, info->irq);
if (!info->ioport || (info->type == PORT_UNKNOWN)) {
- ret += sprintf(buf+ret, "\n");
- return ret;
+ seq_printf(m, "\n");
+ return;
}
- stat_buf[0] = 0;
- stat_buf[1] = 0;
- if (!E100_RTS_GET(info))
- strcat(stat_buf, "|RTS");
- if (!E100_CTS_GET(info))
- strcat(stat_buf, "|CTS");
- if (!E100_DTR_GET(info))
- strcat(stat_buf, "|DTR");
- if (!E100_DSR_GET(info))
- strcat(stat_buf, "|DSR");
- if (!E100_CD_GET(info))
- strcat(stat_buf, "|CD");
- if (!E100_RI_GET(info))
- strcat(stat_buf, "|RI");
-
- ret += sprintf(buf+ret, " baud:%d", info->baud);
-
- ret += sprintf(buf+ret, " tx:%lu rx:%lu",
+ seq_printf(m, " baud:%d", info->baud);
+ seq_printf(m, " tx:%lu rx:%lu",
(unsigned long)info->icount.tx,
(unsigned long)info->icount.rx);
tmp = CIRC_CNT(info->xmit.head, info->xmit.tail, SERIAL_XMIT_SIZE);
- if (tmp) {
- ret += sprintf(buf+ret, " tx_pend:%lu/%lu",
- (unsigned long)tmp,
- (unsigned long)SERIAL_XMIT_SIZE);
- }
+ if (tmp)
+ seq_printf(m, " tx_pend:%lu/%lu",
+ (unsigned long)tmp,
+ (unsigned long)SERIAL_XMIT_SIZE);
- ret += sprintf(buf+ret, " rx_pend:%lu/%lu",
- (unsigned long)info->recv_cnt,
- (unsigned long)info->max_recv_cnt);
+ seq_printf(m, " rx_pend:%lu/%lu",
+ (unsigned long)info->recv_cnt,
+ (unsigned long)info->max_recv_cnt);
#if 1
if (info->port.tty) {
-
if (info->port.tty->stopped)
- ret += sprintf(buf+ret, " stopped:%i",
- (int)info->port.tty->stopped);
+ seq_printf(m, " stopped:%i",
+ (int)info->port.tty->stopped);
if (info->port.tty->hw_stopped)
- ret += sprintf(buf+ret, " hw_stopped:%i",
- (int)info->port.tty->hw_stopped);
+ seq_printf(m, " hw_stopped:%i",
+ (int)info->port.tty->hw_stopped);
}
{
unsigned char rstat = info->ioport[REG_STATUS];
- if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect) )
- ret += sprintf(buf+ret, " xoff_detect:1");
+ if (rstat & IO_MASK(R_SERIAL0_STATUS, xoff_detect))
+ seq_printf(m, " xoff_detect:1");
}
#endif
-
-
-
if (info->icount.frame)
- ret += sprintf(buf+ret, " fe:%lu",
- (unsigned long)info->icount.frame);
+ seq_printf(m, " fe:%lu", (unsigned long)info->icount.frame);
if (info->icount.parity)
- ret += sprintf(buf+ret, " pe:%lu",
- (unsigned long)info->icount.parity);
+ seq_printf(m, " pe:%lu", (unsigned long)info->icount.parity);
if (info->icount.brk)
- ret += sprintf(buf+ret, " brk:%lu",
- (unsigned long)info->icount.brk);
+ seq_printf(m, " brk:%lu", (unsigned long)info->icount.brk);
if (info->icount.overrun)
- ret += sprintf(buf+ret, " oe:%lu",
- (unsigned long)info->icount.overrun);
+ seq_printf(m, " oe:%lu", (unsigned long)info->icount.overrun);
/*
* Last thing is the RS-232 status lines
*/
- ret += sprintf(buf+ret, " %s\n", stat_buf+1);
- return ret;
+ if (!E100_RTS_GET(info))
+ seq_puts(m, "|RTS");
+ if (!E100_CTS_GET(info))
+ seq_puts(m, "|CTS");
+ if (!E100_DTR_GET(info))
+ seq_puts(m, "|DTR");
+ if (!E100_DSR_GET(info))
+ seq_puts(m, "|DSR");
+ if (!E100_CD_GET(info))
+ seq_puts(m, "|CD");
+ if (!E100_RI_GET(info))
+ seq_puts(m, "|RI");
+ seq_puts(m, "\n");
}
-int rs_read_proc(char *page, char **start, off_t off, int count,
- int *eof, void *data)
+
+static int crisv10_proc_show(struct seq_file *m, void *v)
{
- int i, len = 0, l;
- off_t begin = 0;
+ int i;
- len += sprintf(page, "serinfo:1.0 driver:%s\n",
- serial_version);
- for (i = 0; i < NR_PORTS && len < 4000; i++) {
+ seq_printf(m, "serinfo:1.0 driver:%s\n", serial_version);
+
+ for (i = 0; i < NR_PORTS; i++) {
if (!rs_table[i].enabled)
continue;
- l = line_info(page + len, &rs_table[i]);
- len += l;
- if (len+begin > off+count)
- goto done;
- if (len+begin < off) {
- begin += len;
- len = 0;
- }
+ seq_line_info(m, &rs_table[i]);
}
#ifdef DEBUG_LOG_INCLUDED
for (i = 0; i < debug_log_pos; i++) {
- len += sprintf(page + len, "%-4i %lu.%lu ", i, debug_log[i].time, timer_data_to_ns(debug_log[i].timer_data));
- len += sprintf(page + len, debug_log[i].string, debug_log[i].value);
- if (len+begin > off+count)
- goto done;
- if (len+begin < off) {
- begin += len;
- len = 0;
- }
+ seq_printf(m, "%-4i %lu.%lu ",
+ i, debug_log[i].time,
+ timer_data_to_ns(debug_log[i].timer_data));
+ seq_printf(m, debug_log[i].string, debug_log[i].value);
}
- len += sprintf(page + len, "debug_log %i/%i %li bytes\n",
- i, DEBUG_LOG_SIZE, begin+len);
+ seq_printf(m, "debug_log %i/%i\n", i, DEBUG_LOG_SIZE);
debug_log_pos = 0;
#endif
+ return 0;
+}
- *eof = 1;
-done:
- if (off >= len+begin)
- return 0;
- *start = page + (off-begin);
- return ((count < begin+len-off) ? count : begin+len-off);
+static int crisv10_proc_open(struct inode *inode, struct file *file)
+{
+ return single_open(file, crisv10_proc_show, NULL);
}
+static const struct file_operations crisv10_proc_fops = {
+ .owner = THIS_MODULE,
+ .open = crisv10_proc_open,
+ .read = seq_read,
+ .llseek = seq_lseek,
+ .release = single_release,
+};
+#endif
+
+
/* Finally, routines used to initialize the serial driver. */
-static void
-show_serial_version(void)
+static void show_serial_version(void)
{
printk(KERN_INFO
- "ETRAX 100LX serial-driver %s, (c) 2000-2004 Axis Communications AB\r\n",
+ "ETRAX 100LX serial-driver %s, "
+ "(c) 2000-2004 Axis Communications AB\r\n",
&serial_version[11]); /* "$Revision: x.yy" */
}
@@ -4425,13 +4407,14 @@ static const struct tty_operations rs_ops = {
.break_ctl = rs_break,
.send_xchar = rs_send_xchar,
.wait_until_sent = rs_wait_until_sent,
- .read_proc = rs_read_proc,
.tiocmget = rs_tiocmget,
- .tiocmset = rs_tiocmset
+ .tiocmset = rs_tiocmset,
+#ifdef CONFIG_PROC_FS
+ .proc_fops = &crisv10_proc_fops,
+#endif
};
-static int __init
-rs_init(void)
+static int __init rs_init(void)
{
int i;
struct e100_serial *info;
diff --git a/drivers/serial/icom.c b/drivers/serial/icom.c
index 6579e2be1dd..9f2891c2c4a 100644
--- a/drivers/serial/icom.c
+++ b/drivers/serial/icom.c
@@ -137,7 +137,12 @@ static LIST_HEAD(icom_adapter_head);
static spinlock_t icom_lock;
#ifdef ICOM_TRACE
-static inline void trace(struct icom_port *, char *, unsigned long) {};
+static inline void trace(struct icom_port *icom_port, char *trace_pt,
+ unsigned long trace_data)
+{
+ dev_info(&icom_port->adapter->pci_dev->dev, ":%d:%s - %lx\n",
+ icom_port->port, trace_pt, trace_data);
+}
#else
static inline void trace(struct icom_port *icom_port, char *trace_pt, unsigned long trace_data) {};
#endif
@@ -408,7 +413,7 @@ static void load_code(struct icom_port *icom_port)
release_firmware(fw);
/* Set Hardware level */
- if ((icom_port->adapter->version | ADAPTER_V2) == ADAPTER_V2)
+ if (icom_port->adapter->version == ADAPTER_V2)
writeb(V2_HARDWARE, &(icom_port->dram->misc_flags));
/* Start the processor in Adapter */
@@ -861,7 +866,7 @@ static irqreturn_t icom_interrupt(int irq, void *dev_id)
/* find icom_port for this interrupt */
icom_adapter = (struct icom_adapter *) dev_id;
- if ((icom_adapter->version | ADAPTER_V2) == ADAPTER_V2) {
+ if (icom_adapter->version == ADAPTER_V2) {
int_reg = icom_adapter->base_addr + 0x8024;
adapter_interrupts = readl(int_reg);
@@ -1472,8 +1477,8 @@ static void icom_remove_adapter(struct icom_adapter *icom_adapter)
free_irq(icom_adapter->pci_dev->irq, (void *) icom_adapter);
iounmap(icom_adapter->base_addr);
- icom_free_adapter(icom_adapter);
pci_release_regions(icom_adapter->pci_dev);
+ icom_free_adapter(icom_adapter);
}
static void icom_kref_release(struct kref *kref)
@@ -1647,15 +1652,6 @@ static void __exit icom_exit(void)
module_init(icom_init);
module_exit(icom_exit);
-#ifdef ICOM_TRACE
-static inline void trace(struct icom_port *icom_port, char *trace_pt,
- unsigned long trace_data)
-{
- dev_info(&icom_port->adapter->pci_dev->dev, ":%d:%s - %lx\n",
- icom_port->port, trace_pt, trace_data);
-}
-#endif
-
MODULE_AUTHOR("Michael Anderson <mjanders@us.ibm.com>");
MODULE_DESCRIPTION("IBM iSeries Serial IOA driver");
MODULE_SUPPORTED_DEVICE
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 9f460b175c5..7b5d1de9cfe 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -8,6 +8,9 @@
* Author: Sascha Hauer <sascha@saschahauer.de>
* Copyright (C) 2004 Pengutronix
*
+ * Copyright (C) 2009 emlix GmbH
+ * Author: Fabian Godehardt (added IrDA support for iMX)
+ *
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
@@ -41,6 +44,8 @@
#include <linux/serial_core.h>
#include <linux/serial.h>
#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/rational.h>
#include <asm/io.h>
#include <asm/irq.h>
@@ -148,6 +153,7 @@
#define UCR4_DREN (1<<0) /* Recv data ready interrupt enable */
#define UFCR_RXTL_SHF 0 /* Receiver trigger level shift */
#define UFCR_RFDIV (7<<7) /* Reference freq divider mask */
+#define UFCR_RFDIV_REG(x) (((x) < 7 ? 6 - (x) : 6) << 7)
#define UFCR_TXTL_SHF 10 /* Transmitter trigger level shift */
#define USR1_PARITYERR (1<<15) /* Parity error interrupt flag */
#define USR1_RTSS (1<<14) /* RTS pin status */
@@ -211,10 +217,20 @@ struct imx_port {
struct timer_list timer;
unsigned int old_status;
int txirq,rxirq,rtsirq;
- int have_rtscts:1;
+ unsigned int have_rtscts:1;
+ unsigned int use_irda:1;
+ unsigned int irda_inv_rx:1;
+ unsigned int irda_inv_tx:1;
+ unsigned short trcv_delay; /* transceiver delay */
struct clk *clk;
};
+#ifdef CONFIG_IRDA
+#define USE_IRDA(sport) ((sport)->use_irda)
+#else
+#define USE_IRDA(sport) (0)
+#endif
+
/*
* Handle any change of modem status signal since we were last called.
*/
@@ -268,6 +284,48 @@ static void imx_stop_tx(struct uart_port *port)
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
+ if (USE_IRDA(sport)) {
+ /* half duplex - wait for end of transmission */
+ int n = 256;
+ while ((--n > 0) &&
+ !(readl(sport->port.membase + USR2) & USR2_TXDC)) {
+ udelay(5);
+ barrier();
+ }
+ /*
+ * irda transceiver - wait a bit more to avoid
+ * cutoff, hardware dependent
+ */
+ udelay(sport->trcv_delay);
+
+ /*
+ * half duplex - reactivate receive mode,
+ * flush receive pipe echo crap
+ */
+ if (readl(sport->port.membase + USR2) & USR2_TXDC) {
+ temp = readl(sport->port.membase + UCR1);
+ temp &= ~(UCR1_TXMPTYEN | UCR1_TRDYEN);
+ writel(temp, sport->port.membase + UCR1);
+
+ temp = readl(sport->port.membase + UCR4);
+ temp &= ~(UCR4_TCEN);
+ writel(temp, sport->port.membase + UCR4);
+
+ while (readl(sport->port.membase + URXD0) &
+ URXD_CHARRDY)
+ barrier();
+
+ temp = readl(sport->port.membase + UCR1);
+ temp |= UCR1_RRDYEN;
+ writel(temp, sport->port.membase + UCR1);
+
+ temp = readl(sport->port.membase + UCR4);
+ temp |= UCR4_DREN;
+ writel(temp, sport->port.membase + UCR4);
+ }
+ return;
+ }
+
temp = readl(sport->port.membase + UCR1);
writel(temp & ~UCR1_TXMPTYEN, sport->port.membase + UCR1);
}
@@ -302,13 +360,15 @@ static inline void imx_transmit_buffer(struct imx_port *sport)
/* send xmit->buf[xmit->tail]
* out the port here */
writel(xmit->buf[xmit->tail], sport->port.membase + URTX0);
- xmit->tail = (xmit->tail + 1) &
- (UART_XMIT_SIZE - 1);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
sport->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
}
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&sport->port);
+
if (uart_circ_empty(xmit))
imx_stop_tx(&sport->port);
}
@@ -321,9 +381,30 @@ static void imx_start_tx(struct uart_port *port)
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
+ if (USE_IRDA(sport)) {
+ /* half duplex in IrDA mode; have to disable receive mode */
+ temp = readl(sport->port.membase + UCR4);
+ temp &= ~(UCR4_DREN);
+ writel(temp, sport->port.membase + UCR4);
+
+ temp = readl(sport->port.membase + UCR1);
+ temp &= ~(UCR1_RRDYEN);
+ writel(temp, sport->port.membase + UCR1);
+ }
+
temp = readl(sport->port.membase + UCR1);
writel(temp | UCR1_TXMPTYEN, sport->port.membase + UCR1);
+ if (USE_IRDA(sport)) {
+ temp = readl(sport->port.membase + UCR1);
+ temp |= UCR1_TRDYEN;
+ writel(temp, sport->port.membase + UCR1);
+
+ temp = readl(sport->port.membase + UCR4);
+ temp |= UCR4_TCEN;
+ writel(temp, sport->port.membase + UCR4);
+ }
+
if (readl(sport->port.membase + UTS) & UTS_TXEMPTY)
imx_transmit_buffer(sport);
}
@@ -395,8 +476,7 @@ static irqreturn_t imx_rxint(int irq, void *dev_id)
continue;
}
- if (uart_handle_sysrq_char
- (&sport->port, (unsigned char)rx))
+ if (uart_handle_sysrq_char(&sport->port, (unsigned char)rx))
continue;
if (rx & (URXD_PRERR | URXD_OVRRUN | URXD_FRMERR) ) {
@@ -471,26 +551,26 @@ static unsigned int imx_tx_empty(struct uart_port *port)
*/
static unsigned int imx_get_mctrl(struct uart_port *port)
{
- struct imx_port *sport = (struct imx_port *)port;
- unsigned int tmp = TIOCM_DSR | TIOCM_CAR;
+ struct imx_port *sport = (struct imx_port *)port;
+ unsigned int tmp = TIOCM_DSR | TIOCM_CAR;
- if (readl(sport->port.membase + USR1) & USR1_RTSS)
- tmp |= TIOCM_CTS;
+ if (readl(sport->port.membase + USR1) & USR1_RTSS)
+ tmp |= TIOCM_CTS;
- if (readl(sport->port.membase + UCR2) & UCR2_CTS)
- tmp |= TIOCM_RTS;
+ if (readl(sport->port.membase + UCR2) & UCR2_CTS)
+ tmp |= TIOCM_RTS;
- return tmp;
+ return tmp;
}
static void imx_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- struct imx_port *sport = (struct imx_port *)port;
+ struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
temp = readl(sport->port.membase + UCR2) & ~UCR2_CTS;
- if (mctrl & TIOCM_RTS)
+ if (mctrl & TIOCM_RTS)
temp |= UCR2_CTS;
writel(temp, sport->port.membase + UCR2);
@@ -534,12 +614,7 @@ static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
if(!ufcr_rfdiv)
ufcr_rfdiv = 1;
- if(ufcr_rfdiv >= 7)
- ufcr_rfdiv = 6;
- else
- ufcr_rfdiv = 6 - ufcr_rfdiv;
-
- val |= UFCR_RFDIV & (ufcr_rfdiv << 7);
+ val |= UFCR_RFDIV_REG(ufcr_rfdiv);
writel(val, sport->port.membase + UFCR);
@@ -558,8 +633,24 @@ static int imx_startup(struct uart_port *port)
* requesting IRQs
*/
temp = readl(sport->port.membase + UCR4);
+
+ if (USE_IRDA(sport))
+ temp |= UCR4_IRSC;
+
writel(temp & ~UCR4_DREN, sport->port.membase + UCR4);
+ if (USE_IRDA(sport)) {
+ /* reset fifo's and state machines */
+ int i = 100;
+ temp = readl(sport->port.membase + UCR2);
+ temp &= ~UCR2_SRST;
+ writel(temp, sport->port.membase + UCR2);
+ while (!(readl(sport->port.membase + UCR2) & UCR2_SRST) &&
+ (--i > 0)) {
+ udelay(1);
+ }
+ }
+
/*
* Allocate the IRQ(s) i.MX1 has three interrupts whereas later
* chips only have one interrupt.
@@ -575,12 +666,16 @@ static int imx_startup(struct uart_port *port)
if (retval)
goto error_out2;
- retval = request_irq(sport->rtsirq, imx_rtsint,
- (sport->rtsirq < MAX_INTERNAL_IRQ) ? 0 :
- IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
- DRIVER_NAME, sport);
- if (retval)
- goto error_out3;
+ /* do not use RTS IRQ on IrDA */
+ if (!USE_IRDA(sport)) {
+ retval = request_irq(sport->rtsirq, imx_rtsint,
+ (sport->rtsirq < MAX_INTERNAL_IRQ) ? 0 :
+ IRQF_TRIGGER_FALLING |
+ IRQF_TRIGGER_RISING,
+ DRIVER_NAME, sport);
+ if (retval)
+ goto error_out3;
+ }
} else {
retval = request_irq(sport->port.irq, imx_int, 0,
DRIVER_NAME, sport);
@@ -597,18 +692,49 @@ static int imx_startup(struct uart_port *port)
temp = readl(sport->port.membase + UCR1);
temp |= UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN;
+
+ if (USE_IRDA(sport)) {
+ temp |= UCR1_IREN;
+ temp &= ~(UCR1_RTSDEN);
+ }
+
writel(temp, sport->port.membase + UCR1);
temp = readl(sport->port.membase + UCR2);
temp |= (UCR2_RXEN | UCR2_TXEN);
writel(temp, sport->port.membase + UCR2);
+ if (USE_IRDA(sport)) {
+ /* clear RX-FIFO */
+ int i = 64;
+ while ((--i > 0) &&
+ (readl(sport->port.membase + URXD0) & URXD_CHARRDY)) {
+ barrier();
+ }
+ }
+
#if defined CONFIG_ARCH_MX2 || defined CONFIG_ARCH_MX3
temp = readl(sport->port.membase + UCR3);
temp |= UCR3_RXDMUXSEL;
writel(temp, sport->port.membase + UCR3);
#endif
+ if (USE_IRDA(sport)) {
+ temp = readl(sport->port.membase + UCR4);
+ if (sport->irda_inv_rx)
+ temp |= UCR4_INVR;
+ else
+ temp &= ~(UCR4_INVR);
+ writel(temp | UCR4_DREN, sport->port.membase + UCR4);
+
+ temp = readl(sport->port.membase + UCR3);
+ if (sport->irda_inv_tx)
+ temp |= UCR3_INVT;
+ else
+ temp &= ~(UCR3_INVT);
+ writel(temp, sport->port.membase + UCR3);
+ }
+
/*
* Enable modem status interrupts
*/
@@ -616,6 +742,16 @@ static int imx_startup(struct uart_port *port)
imx_enable_ms(&sport->port);
spin_unlock_irqrestore(&sport->port.lock,flags);
+ if (USE_IRDA(sport)) {
+ struct imxuart_platform_data *pdata;
+ pdata = sport->port.dev->platform_data;
+ sport->irda_inv_rx = pdata->irda_inv_rx;
+ sport->irda_inv_tx = pdata->irda_inv_tx;
+ sport->trcv_delay = pdata->transceiver_delay;
+ if (pdata->irda_enable)
+ pdata->irda_enable(1);
+ }
+
return 0;
error_out3:
@@ -633,6 +769,17 @@ static void imx_shutdown(struct uart_port *port)
struct imx_port *sport = (struct imx_port *)port;
unsigned long temp;
+ temp = readl(sport->port.membase + UCR2);
+ temp &= ~(UCR2_TXEN);
+ writel(temp, sport->port.membase + UCR2);
+
+ if (USE_IRDA(sport)) {
+ struct imxuart_platform_data *pdata;
+ pdata = sport->port.dev->platform_data;
+ if (pdata->irda_enable)
+ pdata->irda_enable(0);
+ }
+
/*
* Stop our timer.
*/
@@ -642,7 +789,8 @@ static void imx_shutdown(struct uart_port *port)
* Free the interrupts
*/
if (sport->txirq > 0) {
- free_irq(sport->rtsirq, sport);
+ if (!USE_IRDA(sport))
+ free_irq(sport->rtsirq, sport);
free_irq(sport->txirq, sport);
free_irq(sport->rxirq, sport);
} else
@@ -654,6 +802,9 @@ static void imx_shutdown(struct uart_port *port)
temp = readl(sport->port.membase + UCR1);
temp &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+ if (USE_IRDA(sport))
+ temp &= ~(UCR1_IREN);
+
writel(temp, sport->port.membase + UCR1);
}
@@ -665,7 +816,9 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
unsigned long flags;
unsigned int ucr2, old_ucr1, old_txrxen, baud, quot;
unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
- unsigned int div, num, denom, ufcr;
+ unsigned int div, ufcr;
+ unsigned long num, denom;
+ uint64_t tdiv64;
/*
* If we don't support modem control lines, don't allow
@@ -761,38 +914,39 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
sport->port.membase + UCR2);
old_txrxen &= (UCR2_TXEN | UCR2_RXEN);
- div = sport->port.uartclk / (baud * 16);
- if (div > 7)
- div = 7;
- if (!div)
+ if (USE_IRDA(sport)) {
+ /*
+ * use maximum available submodule frequency to
+ * avoid missing short pulses due to low sampling rate
+ */
div = 1;
-
- num = baud;
- denom = port->uartclk / div / 16;
-
- /* shift num and denom right until they fit into 16 bits */
- while (num > 0x10000 || denom > 0x10000) {
- num >>= 1;
- denom >>= 1;
+ } else {
+ div = sport->port.uartclk / (baud * 16);
+ if (div > 7)
+ div = 7;
+ if (!div)
+ div = 1;
}
- if (num > 0)
- num -= 1;
- if (denom > 0)
- denom -= 1;
- writel(num, sport->port.membase + UBIR);
- writel(denom, sport->port.membase + UBMR);
+ rational_best_approximation(16 * div * baud, sport->port.uartclk,
+ 1 << 16, 1 << 16, &num, &denom);
- if (div == 7)
- div = 6; /* 6 in RFDIV means divide by 7 */
- else
- div = 6 - div;
+ tdiv64 = sport->port.uartclk;
+ tdiv64 *= num;
+ do_div(tdiv64, denom * 16 * div);
+ tty_encode_baud_rate(sport->port.info->port.tty,
+ (speed_t)tdiv64, (speed_t)tdiv64);
+
+ num -= 1;
+ denom -= 1;
ufcr = readl(sport->port.membase + UFCR);
- ufcr = (ufcr & (~UFCR_RFDIV)) |
- (div << 7);
+ ufcr = (ufcr & (~UFCR_RFDIV)) | UFCR_RFDIV_REG(div);
writel(ufcr, sport->port.membase + UFCR);
+ writel(num, sport->port.membase + UBIR);
+ writel(denom, sport->port.membase + UBMR);
+
#ifdef ONEMS
writel(sport->port.uartclk / div / 1000, sport->port.membase + ONEMS);
#endif
@@ -1031,6 +1185,8 @@ imx_console_setup(struct console *co, char *options)
if (co->index == -1 || co->index >= ARRAY_SIZE(imx_ports))
co->index = 0;
sport = imx_ports[co->index];
+ if(sport == NULL)
+ return -ENODEV;
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
@@ -1070,22 +1226,22 @@ static struct uart_driver imx_reg = {
static int serial_imx_suspend(struct platform_device *dev, pm_message_t state)
{
- struct imx_port *sport = platform_get_drvdata(dev);
+ struct imx_port *sport = platform_get_drvdata(dev);
- if (sport)
- uart_suspend_port(&imx_reg, &sport->port);
+ if (sport)
+ uart_suspend_port(&imx_reg, &sport->port);
- return 0;
+ return 0;
}
static int serial_imx_resume(struct platform_device *dev)
{
- struct imx_port *sport = platform_get_drvdata(dev);
+ struct imx_port *sport = platform_get_drvdata(dev);
- if (sport)
- uart_resume_port(&imx_reg, &sport->port);
+ if (sport)
+ uart_resume_port(&imx_reg, &sport->port);
- return 0;
+ return 0;
}
static int serial_imx_probe(struct platform_device *pdev)
@@ -1141,19 +1297,29 @@ static int serial_imx_probe(struct platform_device *pdev)
imx_ports[pdev->id] = sport;
pdata = pdev->dev.platform_data;
- if(pdata && (pdata->flags & IMXUART_HAVE_RTSCTS))
+ if (pdata && (pdata->flags & IMXUART_HAVE_RTSCTS))
sport->have_rtscts = 1;
+#ifdef CONFIG_IRDA
+ if (pdata && (pdata->flags & IMXUART_IRDA))
+ sport->use_irda = 1;
+#endif
+
if (pdata->init) {
ret = pdata->init(pdev);
if (ret)
goto clkput;
}
- uart_add_one_port(&imx_reg, &sport->port);
+ ret = uart_add_one_port(&imx_reg, &sport->port);
+ if (ret)
+ goto deinit;
platform_set_drvdata(pdev, &sport->port);
return 0;
+deinit:
+ if (pdata->exit)
+ pdata->exit(pdev);
clkput:
clk_put(sport->clk);
clk_disable(sport->clk);
@@ -1191,13 +1357,13 @@ static int serial_imx_remove(struct platform_device *pdev)
}
static struct platform_driver serial_imx_driver = {
- .probe = serial_imx_probe,
- .remove = serial_imx_remove,
+ .probe = serial_imx_probe,
+ .remove = serial_imx_remove,
.suspend = serial_imx_suspend,
.resume = serial_imx_resume,
.driver = {
- .name = "imx-uart",
+ .name = "imx-uart",
.owner = THIS_MODULE,
},
};
diff --git a/drivers/serial/jsm/jsm.h b/drivers/serial/jsm/jsm.h
index 8871aaa3dba..4e5f3bde046 100644
--- a/drivers/serial/jsm/jsm.h
+++ b/drivers/serial/jsm/jsm.h
@@ -61,6 +61,7 @@ enum {
if ((DBG_##nlevel & jsm_debug)) \
dev_printk(KERN_##klevel, pdev->dev, fmt, ## args)
+#define MAXLINES 256
#define MAXPORTS 8
#define MAX_STOPS_SENT 5
@@ -130,8 +131,6 @@ struct jsm_board
struct pci_dev *pci_dev;
u32 maxports; /* MAX ports this board can handle */
- spinlock_t bd_lock; /* Used to protect board */
-
spinlock_t bd_intr_lock; /* Used to protect the poller tasklet and
* the interrupt routine from each other.
*/
diff --git a/drivers/serial/jsm/jsm_driver.c b/drivers/serial/jsm/jsm_driver.c
index d2d32a19862..b3604aa322a 100644
--- a/drivers/serial/jsm/jsm_driver.c
+++ b/drivers/serial/jsm/jsm_driver.c
@@ -88,7 +88,6 @@ static int __devinit jsm_probe_one(struct pci_dev *pdev, const struct pci_device
else
brd->maxports = 2;
- spin_lock_init(&brd->bd_lock);
spin_lock_init(&brd->bd_intr_lock);
/* store which revision we have */
diff --git a/drivers/serial/jsm/jsm_tty.c b/drivers/serial/jsm/jsm_tty.c
index 31496dc0a0d..107ce2e187b 100644
--- a/drivers/serial/jsm/jsm_tty.c
+++ b/drivers/serial/jsm/jsm_tty.c
@@ -33,6 +33,8 @@
#include "jsm.h"
+static DECLARE_BITMAP(linemap, MAXLINES);
+
static void jsm_carrier(struct jsm_channel *ch);
static inline int jsm_get_mstat(struct jsm_channel *ch)
@@ -433,6 +435,7 @@ int __devinit jsm_tty_init(struct jsm_board *brd)
int __devinit jsm_uart_port_init(struct jsm_board *brd)
{
int i;
+ unsigned int line;
struct jsm_channel *ch;
if (!brd)
@@ -459,9 +462,15 @@ int __devinit jsm_uart_port_init(struct jsm_board *brd)
brd->channels[i]->uart_port.membase = brd->re_map_membase;
brd->channels[i]->uart_port.fifosize = 16;
brd->channels[i]->uart_port.ops = &jsm_ops;
- brd->channels[i]->uart_port.line = brd->channels[i]->ch_portnum + brd->boardnum * 2;
+ line = find_first_zero_bit(linemap, MAXLINES);
+ if (line >= MAXLINES) {
+ printk(KERN_INFO "jsm: linemap is full, added device failed\n");
+ continue;
+ } else
+ set_bit((int)line, linemap);
+ brd->channels[i]->uart_port.line = line;
if (uart_add_one_port (&jsm_uart_driver, &brd->channels[i]->uart_port))
- printk(KERN_INFO "Added device failed\n");
+ printk(KERN_INFO "jsm: add device failed\n");
else
printk(KERN_INFO "Added device \n");
}
@@ -494,6 +503,7 @@ int jsm_remove_uart_port(struct jsm_board *brd)
ch = brd->channels[i];
+ clear_bit((int)(ch->uart_port.line), linemap);
uart_remove_one_port(&jsm_uart_driver, &brd->channels[i]->uart_port);
}
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 7f72f8ceaa6..b3feb6198d5 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -988,7 +988,7 @@ mpc52xx_console_setup(struct console *co, char *options)
pr_debug("mpc52xx_console_setup co=%p, co->index=%i, options=%s\n",
co, co->index, options);
- if ((co->index < 0) || (co->index > MPC52xx_PSC_MAXNUM)) {
+ if ((co->index < 0) || (co->index >= MPC52xx_PSC_MAXNUM)) {
pr_debug("PSC%x out of range\n", co->index);
return -EINVAL;
}
diff --git a/drivers/serial/nwpserial.c b/drivers/serial/nwpserial.c
index 32f3eaf0d26..9e150b19d72 100644
--- a/drivers/serial/nwpserial.c
+++ b/drivers/serial/nwpserial.c
@@ -145,11 +145,13 @@ static irqreturn_t nwpserial_interrupt(int irq, void *dev_id)
ch = dcr_read(up->dcr_host, UART_RX);
if (up->port.ignore_status_mask != NWPSERIAL_STATUS_RXVALID)
tty_insert_flip_char(tty, ch, TTY_NORMAL);
- } while (dcr_read(up->dcr_host, UART_RX) & UART_LSR_DR);
+ } while (dcr_read(up->dcr_host, UART_LSR) & UART_LSR_DR);
tty_flip_buffer_push(tty);
ret = IRQ_HANDLED;
+ /* clear interrupt */
+ dcr_write(up->dcr_host, UART_IIR, 1);
out:
spin_unlock(&up->port.lock);
return ret;
diff --git a/drivers/serial/s3c6400.c b/drivers/serial/s3c6400.c
index 06936d13393..3e378523368 100644
--- a/drivers/serial/s3c6400.c
+++ b/drivers/serial/s3c6400.c
@@ -102,6 +102,7 @@ static struct s3c24xx_uart_info s3c6400_uart_inf = {
.name = "Samsung S3C6400 UART",
.type = PORT_S3C6400,
.fifosize = 64,
+ .has_divslot = 1,
.rx_fifomask = S3C2440_UFSTAT_RXMASK,
.rx_fifoshift = S3C2440_UFSTAT_RXSHIFT,
.rx_fifofull = S3C2440_UFSTAT_RXFULL,
diff --git a/drivers/serial/samsung.c b/drivers/serial/samsung.c
index e06686ae858..93b5d75db12 100644
--- a/drivers/serial/samsung.c
+++ b/drivers/serial/samsung.c
@@ -508,6 +508,7 @@ s3c24xx_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *c)
struct baud_calc {
struct s3c24xx_uart_clksrc *clksrc;
unsigned int calc;
+ unsigned int divslot;
unsigned int quot;
struct clk *src;
};
@@ -517,6 +518,7 @@ static int s3c24xx_serial_calcbaud(struct baud_calc *calc,
struct s3c24xx_uart_clksrc *clksrc,
unsigned int baud)
{
+ struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned long rate;
calc->src = clk_get(port->dev, clksrc->name);
@@ -527,8 +529,24 @@ static int s3c24xx_serial_calcbaud(struct baud_calc *calc,
rate /= clksrc->divisor;
calc->clksrc = clksrc;
- calc->quot = (rate + (8 * baud)) / (16 * baud);
- calc->calc = (rate / (calc->quot * 16));
+
+ if (ourport->info->has_divslot) {
+ unsigned long div = rate / baud;
+
+ /* The UDIVSLOT register on the newer UARTs allows us to
+ * get a divisor adjustment of 1/16th on the baud clock.
+ *
+ * We don't keep the UDIVSLOT value (the 16ths we calculated
+ * by not multiplying the baud by 16) as it is easy enough
+ * to recalculate.
+ */
+
+ calc->quot = div / 16;
+ calc->calc = rate / div;
+ } else {
+ calc->quot = (rate + (8 * baud)) / (16 * baud);
+ calc->calc = (rate / (calc->quot * 16));
+ }
calc->quot--;
return 1;
@@ -611,6 +629,30 @@ static unsigned int s3c24xx_serial_getclk(struct uart_port *port,
return best->quot;
}
+/* udivslot_table[]
+ *
+ * This table takes the fractional value of the baud divisor and gives
+ * the recommended setting for the UDIVSLOT register.
+ */
+static u16 udivslot_table[16] = {
+ [0] = 0x0000,
+ [1] = 0x0080,
+ [2] = 0x0808,
+ [3] = 0x0888,
+ [4] = 0x2222,
+ [5] = 0x4924,
+ [6] = 0x4A52,
+ [7] = 0x54AA,
+ [8] = 0x5555,
+ [9] = 0xD555,
+ [10] = 0xD5D5,
+ [11] = 0xDDD5,
+ [12] = 0xDDDD,
+ [13] = 0xDFDD,
+ [14] = 0xDFDF,
+ [15] = 0xFFDF,
+};
+
static void s3c24xx_serial_set_termios(struct uart_port *port,
struct ktermios *termios,
struct ktermios *old)
@@ -623,6 +665,7 @@ static void s3c24xx_serial_set_termios(struct uart_port *port,
unsigned int baud, quot;
unsigned int ulcon;
unsigned int umcon;
+ unsigned int udivslot = 0;
/*
* We don't support modem control lines.
@@ -644,6 +687,7 @@ static void s3c24xx_serial_set_termios(struct uart_port *port,
/* check to see if we need to change clock source */
if (ourport->clksrc != clksrc || ourport->baudclk != clk) {
+ dbg("selecting clock %p\n", clk);
s3c24xx_serial_setsource(port, clksrc);
if (ourport->baudclk != NULL && !IS_ERR(ourport->baudclk)) {
@@ -658,6 +702,13 @@ static void s3c24xx_serial_set_termios(struct uart_port *port,
ourport->baudclk_rate = clk ? clk_get_rate(clk) : 0;
}
+ if (ourport->info->has_divslot) {
+ unsigned int div = ourport->baudclk_rate / baud;
+
+ udivslot = udivslot_table[div & 15];
+ dbg("udivslot = %04x (div %d)\n", udivslot, div & 15);
+ }
+
switch (termios->c_cflag & CSIZE) {
case CS5:
dbg("config: 5bits/char\n");
@@ -697,12 +748,16 @@ static void s3c24xx_serial_set_termios(struct uart_port *port,
spin_lock_irqsave(&port->lock, flags);
- dbg("setting ulcon to %08x, brddiv to %d\n", ulcon, quot);
+ dbg("setting ulcon to %08x, brddiv to %d, udivslot %08x\n",
+ ulcon, quot, udivslot);
wr_regl(port, S3C2410_ULCON, ulcon);
wr_regl(port, S3C2410_UBRDIV, quot);
wr_regl(port, S3C2410_UMCON, umcon);
+ if (ourport->info->has_divslot)
+ wr_regl(port, S3C2443_DIVSLOT, udivslot);
+
dbg("uart: ulcon = 0x%08x, ucon = 0x%08x, ufcon = 0x%08x\n",
rd_regl(port, S3C2410_ULCON),
rd_regl(port, S3C2410_UCON),
diff --git a/drivers/serial/samsung.h b/drivers/serial/samsung.h
index 571d6b90d20..7afb94843a0 100644
--- a/drivers/serial/samsung.h
+++ b/drivers/serial/samsung.h
@@ -21,6 +21,10 @@ struct s3c24xx_uart_info {
unsigned long tx_fifoshift;
unsigned long tx_fifofull;
+ /* uart port features */
+
+ unsigned int has_divslot:1;
+
/* clock source control */
int (*get_clksrc)(struct uart_port *, struct s3c24xx_uart_clksrc *clk);
diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index dbf5357a77b..a4cf1079b31 100644
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -47,12 +47,17 @@
#include <linux/clk.h>
#include <linux/ctype.h>
#include <linux/err.h>
+#include <linux/list.h>
#ifdef CONFIG_SUPERH
#include <asm/clock.h>
#include <asm/sh_bios.h>
#endif
+#ifdef CONFIG_H8300
+#include <asm/gpio.h>
+#endif
+
#include "sh-sci.h"
struct sci_port {
@@ -75,14 +80,22 @@ struct sci_port {
int break_flag;
#ifdef CONFIG_HAVE_CLK
- /* Port clock */
- struct clk *clk;
+ /* Interface clock */
+ struct clk *iclk;
+ /* Data clock */
+ struct clk *dclk;
#endif
+ struct list_head node;
};
-#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
-static struct sci_port *serial_console_port;
+struct sh_sci_priv {
+ spinlock_t lock;
+ struct list_head ports;
+
+#ifdef CONFIG_HAVE_CLK
+ struct notifier_block clk_nb;
#endif
+};
/* Function prototypes */
static void sci_stop_tx(struct uart_port *port);
@@ -138,9 +151,8 @@ static void sci_poll_put_char(struct uart_port *port, unsigned char c)
status = sci_in(port, SCxSR);
} while (!(status & SCxSR_TDxE(port)));
- sci_in(port, SCxSR); /* Dummy read */
- sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port));
sci_out(port, SCxTDR, c);
+ sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port) & ~SCxSR_TEND(port));
}
#endif /* CONFIG_CONSOLE_POLL || CONFIG_SERIAL_SH_SCI_CONSOLE */
@@ -159,12 +171,12 @@ static void h8300_sci_config(struct uart_port *port, unsigned int ctrl)
*mstpcrl &= ~mask;
}
-static inline void h8300_sci_enable(struct uart_port *port)
+static void h8300_sci_enable(struct uart_port *port)
{
h8300_sci_config(port, sci_enable);
}
-static inline void h8300_sci_disable(struct uart_port *port)
+static void h8300_sci_disable(struct uart_port *port)
{
h8300_sci_config(port, sci_disable);
}
@@ -611,7 +623,7 @@ static inline int sci_handle_breaks(struct uart_port *port)
int copied = 0;
unsigned short status = sci_in(port, SCxSR);
struct tty_struct *tty = port->info->port.tty;
- struct sci_port *s = &sci_ports[port->line];
+ struct sci_port *s = to_sci_port(port);
if (uart_handle_break(port))
return 0;
@@ -726,19 +738,43 @@ static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr)
static int sci_notifier(struct notifier_block *self,
unsigned long phase, void *p)
{
- int i;
+ struct sh_sci_priv *priv = container_of(self,
+ struct sh_sci_priv, clk_nb);
+ struct sci_port *sci_port;
+ unsigned long flags;
if ((phase == CPUFREQ_POSTCHANGE) ||
- (phase == CPUFREQ_RESUMECHANGE))
- for (i = 0; i < SCI_NPORTS; i++) {
- struct sci_port *s = &sci_ports[i];
- s->port.uartclk = clk_get_rate(s->clk);
- }
+ (phase == CPUFREQ_RESUMECHANGE)) {
+ spin_lock_irqsave(&priv->lock, flags);
+ list_for_each_entry(sci_port, &priv->ports, node)
+ sci_port->port.uartclk = clk_get_rate(sci_port->dclk);
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+ }
return NOTIFY_OK;
}
-static struct notifier_block sci_nb = { &sci_notifier, NULL, 0 };
+static void sci_clk_enable(struct uart_port *port)
+{
+ struct sci_port *sci_port = to_sci_port(port);
+
+ clk_enable(sci_port->dclk);
+ sci_port->port.uartclk = clk_get_rate(sci_port->dclk);
+
+ if (sci_port->iclk)
+ clk_enable(sci_port->iclk);
+}
+
+static void sci_clk_disable(struct uart_port *port)
+{
+ struct sci_port *sci_port = to_sci_port(port);
+
+ if (sci_port->iclk)
+ clk_disable(sci_port->iclk);
+
+ clk_disable(sci_port->dclk);
+}
#endif
static int sci_request_irq(struct sci_port *port)
@@ -865,15 +901,11 @@ static void sci_break_ctl(struct uart_port *port, int break_state)
static int sci_startup(struct uart_port *port)
{
- struct sci_port *s = &sci_ports[port->line];
+ struct sci_port *s = to_sci_port(port);
if (s->enable)
s->enable(port);
-#ifdef CONFIG_HAVE_CLK
- s->clk = clk_get(NULL, "module_clk");
-#endif
-
sci_request_irq(s);
sci_start_tx(port);
sci_start_rx(port, 1);
@@ -883,7 +915,7 @@ static int sci_startup(struct uart_port *port)
static void sci_shutdown(struct uart_port *port)
{
- struct sci_port *s = &sci_ports[port->line];
+ struct sci_port *s = to_sci_port(port);
sci_stop_rx(port);
sci_stop_tx(port);
@@ -891,11 +923,6 @@ static void sci_shutdown(struct uart_port *port)
if (s->disable)
s->disable(port);
-
-#ifdef CONFIG_HAVE_CLK
- clk_put(s->clk);
- s->clk = NULL;
-#endif
}
static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
@@ -980,25 +1007,31 @@ static int sci_request_port(struct uart_port *port)
static void sci_config_port(struct uart_port *port, int flags)
{
- struct sci_port *s = &sci_ports[port->line];
+ struct sci_port *s = to_sci_port(port);
port->type = s->type;
- if (port->flags & UPF_IOREMAP && !port->membase) {
-#if defined(CONFIG_SUPERH64)
- port->mapbase = onchip_remap(SCIF_ADDR_SH5, 1024, "SCIF");
- port->membase = (void __iomem *)port->mapbase;
-#else
+ if (port->membase)
+ return;
+
+ if (port->flags & UPF_IOREMAP) {
port->membase = ioremap_nocache(port->mapbase, 0x40);
-#endif
- dev_err(port->dev, "can't remap port#%d\n", port->line);
+ if (IS_ERR(port->membase))
+ dev_err(port->dev, "can't remap port#%d\n", port->line);
+ } else {
+ /*
+ * For the simple (and majority of) cases where we don't
+ * need to do any remapping, just cast the cookie
+ * directly.
+ */
+ port->membase = (void __iomem *)port->mapbase;
}
}
static int sci_verify_port(struct uart_port *port, struct serial_struct *ser)
{
- struct sci_port *s = &sci_ports[port->line];
+ struct sci_port *s = to_sci_port(port);
if (ser->irq != s->irqs[SCIx_TXI_IRQ] || ser->irq > nr_irqs)
return -EINVAL;
@@ -1032,63 +1065,60 @@ static struct uart_ops sci_uart_ops = {
#endif
};
-static void __init sci_init_ports(void)
+static void __devinit sci_init_single(struct platform_device *dev,
+ struct sci_port *sci_port,
+ unsigned int index,
+ struct plat_sci_port *p)
{
- static int first = 1;
- int i;
-
- if (!first)
- return;
-
- first = 0;
-
- for (i = 0; i < SCI_NPORTS; i++) {
- sci_ports[i].port.ops = &sci_uart_ops;
- sci_ports[i].port.iotype = UPIO_MEM;
- sci_ports[i].port.line = i;
- sci_ports[i].port.fifosize = 1;
+ sci_port->port.ops = &sci_uart_ops;
+ sci_port->port.iotype = UPIO_MEM;
+ sci_port->port.line = index;
+ sci_port->port.fifosize = 1;
#if defined(__H8300H__) || defined(__H8300S__)
#ifdef __H8300S__
- sci_ports[i].enable = h8300_sci_enable;
- sci_ports[i].disable = h8300_sci_disable;
+ sci_port->enable = h8300_sci_enable;
+ sci_port->disable = h8300_sci_disable;
#endif
- sci_ports[i].port.uartclk = CONFIG_CPU_CLOCK;
+ sci_port->port.uartclk = CONFIG_CPU_CLOCK;
#elif defined(CONFIG_HAVE_CLK)
- /*
- * XXX: We should use a proper SCI/SCIF clock
- */
- {
- struct clk *clk = clk_get(NULL, "module_clk");
- sci_ports[i].port.uartclk = clk_get_rate(clk);
- clk_put(clk);
- }
+ sci_port->iclk = p->clk ? clk_get(&dev->dev, p->clk) : NULL;
+ sci_port->dclk = clk_get(&dev->dev, "peripheral_clk");
+ sci_port->enable = sci_clk_enable;
+ sci_port->disable = sci_clk_disable;
#else
#error "Need a valid uartclk"
#endif
- sci_ports[i].break_timer.data = (unsigned long)&sci_ports[i];
- sci_ports[i].break_timer.function = sci_break_timer;
+ sci_port->break_timer.data = (unsigned long)sci_port;
+ sci_port->break_timer.function = sci_break_timer;
+ init_timer(&sci_port->break_timer);
- init_timer(&sci_ports[i].break_timer);
- }
-}
-
-int __init early_sci_setup(struct uart_port *port)
-{
- if (unlikely(port->line > SCI_NPORTS))
- return -ENODEV;
+ sci_port->port.mapbase = p->mapbase;
+ sci_port->port.membase = p->membase;
- sci_init_ports();
+ sci_port->port.irq = p->irqs[SCIx_TXI_IRQ];
+ sci_port->port.flags = p->flags;
+ sci_port->port.dev = &dev->dev;
+ sci_port->type = sci_port->port.type = p->type;
- sci_ports[port->line].port.membase = port->membase;
- sci_ports[port->line].port.mapbase = port->mapbase;
- sci_ports[port->line].port.type = port->type;
+ memcpy(&sci_port->irqs, &p->irqs, sizeof(p->irqs));
- return 0;
}
#ifdef CONFIG_SERIAL_SH_SCI_CONSOLE
+static struct tty_driver *serial_console_device(struct console *co, int *index)
+{
+ struct uart_driver *p = &sci_uart_driver;
+ *index = co->index;
+ return p->tty_driver;
+}
+
+static void serial_console_putchar(struct uart_port *port, int ch)
+{
+ sci_poll_put_char(port, ch);
+}
+
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
@@ -1096,25 +1126,27 @@ int __init early_sci_setup(struct uart_port *port)
static void serial_console_write(struct console *co, const char *s,
unsigned count)
{
- struct uart_port *port = &serial_console_port->port;
+ struct uart_port *port = co->data;
+ struct sci_port *sci_port = to_sci_port(port);
unsigned short bits;
- int i;
- for (i = 0; i < count; i++) {
- if (*s == 10)
- sci_poll_put_char(port, '\r');
+ if (sci_port->enable)
+ sci_port->enable(port);
- sci_poll_put_char(port, *s++);
- }
+ uart_console_write(port, s, count, serial_console_putchar);
/* wait until fifo is empty and last bit has been transmitted */
bits = SCxSR_TDxE(port) | SCxSR_TEND(port);
while ((sci_in(port, SCxSR) & bits) != bits)
cpu_relax();
+
+ if (sci_port->disable);
+ sci_port->disable(port);
}
static int __init serial_console_setup(struct console *co, char *options)
{
+ struct sci_port *sci_port;
struct uart_port *port;
int baud = 115200;
int bits = 8;
@@ -1130,8 +1162,9 @@ static int __init serial_console_setup(struct console *co, char *options)
if (co->index >= SCI_NPORTS)
co->index = 0;
- serial_console_port = &sci_ports[co->index];
- port = &serial_console_port->port;
+ sci_port = &sci_ports[co->index];
+ port = &sci_port->port;
+ co->data = port;
/*
* Also need to check port->type, we don't actually have any
@@ -1141,21 +1174,11 @@ static int __init serial_console_setup(struct console *co, char *options)
*/
if (!port->type)
return -ENODEV;
- if (!port->membase || !port->mapbase)
- return -ENODEV;
-
- port->type = serial_console_port->type;
-
-#ifdef CONFIG_HAVE_CLK
- if (!serial_console_port->clk)
- serial_console_port->clk = clk_get(NULL, "module_clk");
-#endif
- if (port->flags & UPF_IOREMAP)
- sci_config_port(port, 0);
+ sci_config_port(port, 0);
- if (serial_console_port->enable)
- serial_console_port->enable(port);
+ if (sci_port->enable)
+ sci_port->enable(port);
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
@@ -1166,22 +1189,21 @@ static int __init serial_console_setup(struct console *co, char *options)
if (ret == 0)
sci_stop_rx(port);
#endif
+ /* TODO: disable clock */
return ret;
}
static struct console serial_console = {
.name = "ttySC",
- .device = uart_console_device,
+ .device = serial_console_device,
.write = serial_console_write,
.setup = serial_console_setup,
.flags = CON_PRINTBUFFER,
.index = -1,
- .data = &sci_uart_driver,
};
static int __init sci_console_init(void)
{
- sci_init_ports();
register_console(&serial_console);
return 0;
}
@@ -1207,6 +1229,61 @@ static struct uart_driver sci_uart_driver = {
.cons = SCI_CONSOLE,
};
+
+static int sci_remove(struct platform_device *dev)
+{
+ struct sh_sci_priv *priv = platform_get_drvdata(dev);
+ struct sci_port *p;
+ unsigned long flags;
+
+#ifdef CONFIG_HAVE_CLK
+ cpufreq_unregister_notifier(&priv->clk_nb, CPUFREQ_TRANSITION_NOTIFIER);
+#endif
+
+ spin_lock_irqsave(&priv->lock, flags);
+ list_for_each_entry(p, &priv->ports, node)
+ uart_remove_one_port(&sci_uart_driver, &p->port);
+
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ kfree(priv);
+ return 0;
+}
+
+static int __devinit sci_probe_single(struct platform_device *dev,
+ unsigned int index,
+ struct plat_sci_port *p,
+ struct sci_port *sciport)
+{
+ struct sh_sci_priv *priv = platform_get_drvdata(dev);
+ unsigned long flags;
+ int ret;
+
+ /* Sanity check */
+ if (unlikely(index >= SCI_NPORTS)) {
+ dev_notice(&dev->dev, "Attempting to register port "
+ "%d when only %d are available.\n",
+ index+1, SCI_NPORTS);
+ dev_notice(&dev->dev, "Consider bumping "
+ "CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
+ return 0;
+ }
+
+ sci_init_single(dev, sciport, index, p);
+
+ ret = uart_add_one_port(&sci_uart_driver, &sciport->port);
+ if (ret)
+ return ret;
+
+ INIT_LIST_HEAD(&sciport->node);
+
+ spin_lock_irqsave(&priv->lock, flags);
+ list_add(&sciport->node, &priv->ports);
+ spin_unlock_irqrestore(&priv->lock, flags);
+
+ return 0;
+}
+
/*
* Register a set of serial devices attached to a platform device. The
* list is terminated with a zero flags entry, which means we expect
@@ -1216,57 +1293,34 @@ static struct uart_driver sci_uart_driver = {
static int __devinit sci_probe(struct platform_device *dev)
{
struct plat_sci_port *p = dev->dev.platform_data;
+ struct sh_sci_priv *priv;
int i, ret = -EINVAL;
- for (i = 0; p && p->flags != 0; p++, i++) {
- struct sci_port *sciport = &sci_ports[i];
+ priv = kzalloc(sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
- /* Sanity check */
- if (unlikely(i == SCI_NPORTS)) {
- dev_notice(&dev->dev, "Attempting to register port "
- "%d when only %d are available.\n",
- i+1, SCI_NPORTS);
- dev_notice(&dev->dev, "Consider bumping "
- "CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
- break;
- }
+ INIT_LIST_HEAD(&priv->ports);
+ spin_lock_init(&priv->lock);
+ platform_set_drvdata(dev, priv);
- sciport->port.mapbase = p->mapbase;
+#ifdef CONFIG_HAVE_CLK
+ priv->clk_nb.notifier_call = sci_notifier;
+ cpufreq_register_notifier(&priv->clk_nb, CPUFREQ_TRANSITION_NOTIFIER);
+#endif
- if (p->mapbase && !p->membase) {
- if (p->flags & UPF_IOREMAP) {
- p->membase = ioremap_nocache(p->mapbase, 0x40);
- if (IS_ERR(p->membase)) {
- ret = PTR_ERR(p->membase);
- goto err_unreg;
- }
- } else {
- /*
- * For the simple (and majority of) cases
- * where we don't need to do any remapping,
- * just cast the cookie directly.
- */
- p->membase = (void __iomem *)p->mapbase;
- }
+ if (dev->id != -1) {
+ ret = sci_probe_single(dev, dev->id, p, &sci_ports[dev->id]);
+ if (ret)
+ goto err_unreg;
+ } else {
+ for (i = 0; p && p->flags != 0; p++, i++) {
+ ret = sci_probe_single(dev, i, p, &sci_ports[i]);
+ if (ret)
+ goto err_unreg;
}
-
- sciport->port.membase = p->membase;
-
- sciport->port.irq = p->irqs[SCIx_TXI_IRQ];
- sciport->port.flags = p->flags;
- sciport->port.dev = &dev->dev;
-
- sciport->type = sciport->port.type = p->type;
-
- memcpy(&sciport->irqs, &p->irqs, sizeof(p->irqs));
-
- uart_add_one_port(&sci_uart_driver, &sciport->port);
}
-#ifdef CONFIG_HAVE_CLK
- cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
-#endif
-
#ifdef CONFIG_SH_STANDARD_BIOS
sh_bios_gdb_detach();
#endif
@@ -1274,50 +1328,36 @@ static int __devinit sci_probe(struct platform_device *dev)
return 0;
err_unreg:
- for (i = i - 1; i >= 0; i--)
- uart_remove_one_port(&sci_uart_driver, &sci_ports[i].port);
-
+ sci_remove(dev);
return ret;
}
-static int __devexit sci_remove(struct platform_device *dev)
-{
- int i;
-
-#ifdef CONFIG_HAVE_CLK
- cpufreq_unregister_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
-#endif
-
- for (i = 0; i < SCI_NPORTS; i++)
- uart_remove_one_port(&sci_uart_driver, &sci_ports[i].port);
-
- return 0;
-}
-
static int sci_suspend(struct platform_device *dev, pm_message_t state)
{
- int i;
+ struct sh_sci_priv *priv = platform_get_drvdata(dev);
+ struct sci_port *p;
+ unsigned long flags;
- for (i = 0; i < SCI_NPORTS; i++) {
- struct sci_port *p = &sci_ports[i];
+ spin_lock_irqsave(&priv->lock, flags);
+ list_for_each_entry(p, &priv->ports, node)
+ uart_suspend_port(&sci_uart_driver, &p->port);
- if (p->type != PORT_UNKNOWN && p->port.dev == &dev->dev)
- uart_suspend_port(&sci_uart_driver, &p->port);
- }
+ spin_unlock_irqrestore(&priv->lock, flags);
return 0;
}
static int sci_resume(struct platform_device *dev)
{
- int i;
+ struct sh_sci_priv *priv = platform_get_drvdata(dev);
+ struct sci_port *p;
+ unsigned long flags;
- for (i = 0; i < SCI_NPORTS; i++) {
- struct sci_port *p = &sci_ports[i];
+ spin_lock_irqsave(&priv->lock, flags);
+ list_for_each_entry(p, &priv->ports, node)
+ uart_resume_port(&sci_uart_driver, &p->port);
- if (p->type != PORT_UNKNOWN && p->port.dev == &dev->dev)
- uart_resume_port(&sci_uart_driver, &p->port);
- }
+ spin_unlock_irqrestore(&priv->lock, flags);
return 0;
}
@@ -1339,8 +1379,6 @@ static int __init sci_init(void)
printk(banner);
- sci_init_ports();
-
ret = uart_register_driver(&sci_uart_driver);
if (likely(ret == 0)) {
ret = platform_driver_register(&sci_driver);
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index d0aa82d7fce..38072c15b84 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -91,6 +91,9 @@
# define SCSPTR5 0xa4050128
# define SCIF_ORER 0x0001 /* overrun error bit */
# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
+#elif defined(CONFIG_CPU_SUBTYPE_SH7724)
+# define SCIF_ORER 0x0001 /* overrun error bit */
+# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
#elif defined(CONFIG_CPU_SUBTYPE_SH4_202)
# define SCSPTR2 0xffe80020 /* 16 bit SCIF */
# define SCIF_ORER 0x0001 /* overrun error bit */
@@ -314,7 +317,18 @@
} \
}
-#define CPU_SCIF_FNS(name, scif_offset, scif_size) \
+#ifdef CONFIG_H8300
+/* h8300 don't have SCIF */
+#define CPU_SCIF_FNS(name) \
+ static inline unsigned int sci_##name##_in(struct uart_port *port) \
+ { \
+ return 0; \
+ } \
+ static inline void sci_##name##_out(struct uart_port *port, unsigned int value) \
+ { \
+ }
+#else
+#define CPU_SCIF_FNS(name, scif_offset, scif_size) \
static inline unsigned int sci_##name##_in(struct uart_port *port) \
{ \
SCI_IN(scif_size, scif_offset); \
@@ -323,6 +337,7 @@
{ \
SCI_OUT(scif_size, scif_offset, value); \
}
+#endif
#define CPU_SCI_FNS(name, sci_offset, sci_size) \
static inline unsigned int sci_##name##_in(struct uart_port* port) \
@@ -360,8 +375,10 @@
sh3_scif_offset, sh3_scif_size, sh4_scif_offset, sh4_scif_size, \
h8_sci_offset, h8_sci_size) \
CPU_SCI_FNS(name, h8_sci_offset, h8_sci_size)
-#define SCIF_FNS(name, sh3_scif_offset, sh3_scif_size, sh4_scif_offset, sh4_scif_size)
-#elif defined(CONFIG_CPU_SUBTYPE_SH7723)
+#define SCIF_FNS(name, sh3_scif_offset, sh3_scif_size, sh4_scif_offset, sh4_scif_size) \
+ CPU_SCIF_FNS(name)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7723) ||\
+ defined(CONFIG_CPU_SUBTYPE_SH7724)
#define SCIx_FNS(name, sh4_scifa_offset, sh4_scifa_size, sh4_scif_offset, sh4_scif_size) \
CPU_SCIx_FNS(name, sh4_scifa_offset, sh4_scifa_size, sh4_scif_offset, sh4_scif_size)
#define SCIF_FNS(name, sh4_scif_offset, sh4_scif_size) \
@@ -390,7 +407,8 @@ SCIF_FNS(SCFDR, 0x1c, 16)
SCIF_FNS(SCxTDR, 0x20, 8)
SCIF_FNS(SCxRDR, 0x24, 8)
SCIF_FNS(SCLSR, 0x24, 16)
-#elif defined(CONFIG_CPU_SUBTYPE_SH7723)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7723) ||\
+ defined(CONFIG_CPU_SUBTYPE_SH7724)
SCIx_FNS(SCSMR, 0x00, 16, 0x00, 16)
SCIx_FNS(SCBRR, 0x04, 8, 0x04, 8)
SCIx_FNS(SCSCR, 0x08, 16, 0x08, 16)
@@ -604,10 +622,21 @@ static inline int sci_rxd_in(struct uart_port *port)
return ctrl_inb(SCSPTR5) & 0x0008 ? 1 : 0; /* SCIF5 */
return 1;
}
+#elif defined(CONFIG_CPU_SUBTYPE_SH7724)
+# define SCFSR 0x0010
+# define SCASSR 0x0014
+static inline int sci_rxd_in(struct uart_port *port)
+{
+ if (port->type == PORT_SCIF)
+ return ctrl_inw((port->mapbase + SCFSR)) & SCIF_BRK ? 1 : 0;
+ if (port->type == PORT_SCIFA)
+ return ctrl_inw((port->mapbase + SCASSR)) & SCIF_BRK ? 1 : 0;
+ return 1;
+}
#elif defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103)
static inline int sci_rxd_in(struct uart_port *port)
{
- return sci_in(port, SCSPTR2)&0x0001 ? 1 : 0; /* SCIF */
+ return sci_in(port, SCSPTR)&0x0001 ? 1 : 0; /* SCIF */
}
#elif defined(__H8300H__) || defined(__H8300S__)
static inline int sci_rxd_in(struct uart_port *port)
@@ -757,7 +786,8 @@ static inline int sci_rxd_in(struct uart_port *port)
defined(CONFIG_CPU_SUBTYPE_SH7720) || \
defined(CONFIG_CPU_SUBTYPE_SH7721)
#define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1)
-#elif defined(CONFIG_CPU_SUBTYPE_SH7723)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7723) ||\
+ defined(CONFIG_CPU_SUBTYPE_SH7724)
static inline int scbrr_calc(struct uart_port *port, int bps, int clk)
{
if (port->type == PORT_SCIF)
diff --git a/drivers/serial/timbuart.c b/drivers/serial/timbuart.c
new file mode 100644
index 00000000000..ac9e5d5f742
--- /dev/null
+++ b/drivers/serial/timbuart.c
@@ -0,0 +1,526 @@
+/*
+ * timbuart.c timberdale FPGA UART driver
+ * Copyright (c) 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Supports:
+ * Timberdale FPGA UART
+ */
+
+#include <linux/pci.h>
+#include <linux/interrupt.h>
+#include <linux/serial_core.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+#include <linux/ioport.h>
+
+#include "timbuart.h"
+
+struct timbuart_port {
+ struct uart_port port;
+ struct tasklet_struct tasklet;
+ int usedma;
+ u8 last_ier;
+ struct platform_device *dev;
+};
+
+static int baudrates[] = {9600, 19200, 38400, 57600, 115200, 230400, 460800,
+ 921600, 1843200, 3250000};
+
+static void timbuart_mctrl_check(struct uart_port *port, u8 isr, u8 *ier);
+
+static irqreturn_t timbuart_handleinterrupt(int irq, void *devid);
+
+static void timbuart_stop_rx(struct uart_port *port)
+{
+ /* spin lock held by upper layer, disable all RX interrupts */
+ u8 ier = ioread8(port->membase + TIMBUART_IER) & ~RXFLAGS;
+ iowrite8(ier, port->membase + TIMBUART_IER);
+}
+
+static void timbuart_stop_tx(struct uart_port *port)
+{
+ /* spinlock held by upper layer, disable TX interrupt */
+ u8 ier = ioread8(port->membase + TIMBUART_IER) & ~TXBAE;
+ iowrite8(ier, port->membase + TIMBUART_IER);
+}
+
+static void timbuart_start_tx(struct uart_port *port)
+{
+ struct timbuart_port *uart =
+ container_of(port, struct timbuart_port, port);
+
+ /* do not transfer anything here -> fire off the tasklet */
+ tasklet_schedule(&uart->tasklet);
+}
+
+static void timbuart_flush_buffer(struct uart_port *port)
+{
+ u8 ctl = ioread8(port->membase + TIMBUART_CTRL) | TIMBUART_CTRL_FLSHTX;
+
+ iowrite8(ctl, port->membase + TIMBUART_CTRL);
+ iowrite8(TXBF, port->membase + TIMBUART_ISR);
+}
+
+static void timbuart_rx_chars(struct uart_port *port)
+{
+ struct tty_struct *tty = port->info->port.tty;
+
+ while (ioread8(port->membase + TIMBUART_ISR) & RXDP) {
+ u8 ch = ioread8(port->membase + TIMBUART_RXFIFO);
+ port->icount.rx++;
+ tty_insert_flip_char(tty, ch, TTY_NORMAL);
+ }
+
+ spin_unlock(&port->lock);
+ tty_flip_buffer_push(port->info->port.tty);
+ spin_lock(&port->lock);
+
+ dev_dbg(port->dev, "%s - total read %d bytes\n",
+ __func__, port->icount.rx);
+}
+
+static void timbuart_tx_chars(struct uart_port *port)
+{
+ struct circ_buf *xmit = &port->info->xmit;
+
+ while (!(ioread8(port->membase + TIMBUART_ISR) & TXBF) &&
+ !uart_circ_empty(xmit)) {
+ iowrite8(xmit->buf[xmit->tail],
+ port->membase + TIMBUART_TXFIFO);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ port->icount.tx++;
+ }
+
+ dev_dbg(port->dev,
+ "%s - total written %d bytes, CTL: %x, RTS: %x, baud: %x\n",
+ __func__,
+ port->icount.tx,
+ ioread8(port->membase + TIMBUART_CTRL),
+ port->mctrl & TIOCM_RTS,
+ ioread8(port->membase + TIMBUART_BAUDRATE));
+}
+
+static void timbuart_handle_tx_port(struct uart_port *port, u8 isr, u8 *ier)
+{
+ struct timbuart_port *uart =
+ container_of(port, struct timbuart_port, port);
+ struct circ_buf *xmit = &port->info->xmit;
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(port))
+ return;
+
+ if (port->x_char)
+ return;
+
+ if (isr & TXFLAGS) {
+ timbuart_tx_chars(port);
+ /* clear all TX interrupts */
+ iowrite8(TXFLAGS, port->membase + TIMBUART_ISR);
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(port);
+ } else
+ /* Re-enable any tx interrupt */
+ *ier |= uart->last_ier & TXFLAGS;
+
+ /* enable interrupts if there are chars in the transmit buffer,
+ * Or if we delivered some bytes and want the almost empty interrupt
+ * we wake up the upper layer later when we got the interrupt
+ * to give it some time to go out...
+ */
+ if (!uart_circ_empty(xmit))
+ *ier |= TXBAE;
+
+ dev_dbg(port->dev, "%s - leaving\n", __func__);
+}
+
+void timbuart_handle_rx_port(struct uart_port *port, u8 isr, u8 *ier)
+{
+ if (isr & RXFLAGS) {
+ /* Some RX status is set */
+ if (isr & RXBF) {
+ u8 ctl = ioread8(port->membase + TIMBUART_CTRL) |
+ TIMBUART_CTRL_FLSHRX;
+ iowrite8(ctl, port->membase + TIMBUART_CTRL);
+ port->icount.overrun++;
+ } else if (isr & (RXDP))
+ timbuart_rx_chars(port);
+
+ /* ack all RX interrupts */
+ iowrite8(RXFLAGS, port->membase + TIMBUART_ISR);
+ }
+
+ /* always have the RX interrupts enabled */
+ *ier |= RXBAF | RXBF | RXTT;
+
+ dev_dbg(port->dev, "%s - leaving\n", __func__);
+}
+
+void timbuart_tasklet(unsigned long arg)
+{
+ struct timbuart_port *uart = (struct timbuart_port *)arg;
+ u8 isr, ier = 0;
+
+ spin_lock(&uart->port.lock);
+
+ isr = ioread8(uart->port.membase + TIMBUART_ISR);
+ dev_dbg(uart->port.dev, "%s ISR: %x\n", __func__, isr);
+
+ if (!uart->usedma)
+ timbuart_handle_tx_port(&uart->port, isr, &ier);
+
+ timbuart_mctrl_check(&uart->port, isr, &ier);
+
+ if (!uart->usedma)
+ timbuart_handle_rx_port(&uart->port, isr, &ier);
+
+ iowrite8(ier, uart->port.membase + TIMBUART_IER);
+
+ spin_unlock(&uart->port.lock);
+ dev_dbg(uart->port.dev, "%s leaving\n", __func__);
+}
+
+static unsigned int timbuart_tx_empty(struct uart_port *port)
+{
+ u8 isr = ioread8(port->membase + TIMBUART_ISR);
+
+ return (isr & TXBAE) ? TIOCSER_TEMT : 0;
+}
+
+static unsigned int timbuart_get_mctrl(struct uart_port *port)
+{
+ u8 cts = ioread8(port->membase + TIMBUART_CTRL);
+ dev_dbg(port->dev, "%s - cts %x\n", __func__, cts);
+
+ if (cts & TIMBUART_CTRL_CTS)
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+ else
+ return TIOCM_DSR | TIOCM_CAR;
+}
+
+static void timbuart_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+ dev_dbg(port->dev, "%s - %x\n", __func__, mctrl);
+
+ if (mctrl & TIOCM_RTS)
+ iowrite8(TIMBUART_CTRL_RTS, port->membase + TIMBUART_CTRL);
+ else
+ iowrite8(TIMBUART_CTRL_RTS, port->membase + TIMBUART_CTRL);
+}
+
+static void timbuart_mctrl_check(struct uart_port *port, u8 isr, u8 *ier)
+{
+ unsigned int cts;
+
+ if (isr & CTS_DELTA) {
+ /* ack */
+ iowrite8(CTS_DELTA, port->membase + TIMBUART_ISR);
+ cts = timbuart_get_mctrl(port);
+ uart_handle_cts_change(port, cts & TIOCM_CTS);
+ wake_up_interruptible(&port->info->delta_msr_wait);
+ }
+
+ *ier |= CTS_DELTA;
+}
+
+static void timbuart_enable_ms(struct uart_port *port)
+{
+ /* N/A */
+}
+
+static void timbuart_break_ctl(struct uart_port *port, int ctl)
+{
+ /* N/A */
+}
+
+static int timbuart_startup(struct uart_port *port)
+{
+ struct timbuart_port *uart =
+ container_of(port, struct timbuart_port, port);
+
+ dev_dbg(port->dev, "%s\n", __func__);
+
+ iowrite8(TIMBUART_CTRL_FLSHRX, port->membase + TIMBUART_CTRL);
+ iowrite8(0xff, port->membase + TIMBUART_ISR);
+ /* Enable all but TX interrupts */
+ iowrite8(RXBAF | RXBF | RXTT | CTS_DELTA,
+ port->membase + TIMBUART_IER);
+
+ return request_irq(port->irq, timbuart_handleinterrupt, IRQF_SHARED,
+ "timb-uart", uart);
+}
+
+static void timbuart_shutdown(struct uart_port *port)
+{
+ struct timbuart_port *uart =
+ container_of(port, struct timbuart_port, port);
+ dev_dbg(port->dev, "%s\n", __func__);
+ free_irq(port->irq, uart);
+ iowrite8(0, port->membase + TIMBUART_IER);
+}
+
+static int get_bindex(int baud)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(baudrates); i++)
+ if (baud <= baudrates[i])
+ return i;
+
+ return -1;
+}
+
+static void timbuart_set_termios(struct uart_port *port,
+ struct ktermios *termios,
+ struct ktermios *old)
+{
+ unsigned int baud;
+ short bindex;
+ unsigned long flags;
+
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk / 16);
+ bindex = get_bindex(baud);
+ dev_dbg(port->dev, "%s - bindex %d\n", __func__, bindex);
+
+ if (bindex < 0)
+ bindex = 0;
+ baud = baudrates[bindex];
+
+ /* The serial layer calls into this once with old = NULL when setting
+ up initially */
+ if (old)
+ tty_termios_copy_hw(termios, old);
+ tty_termios_encode_baud_rate(termios, baud, baud);
+
+ spin_lock_irqsave(&port->lock, flags);
+ iowrite8((u8)bindex, port->membase + TIMBUART_BAUDRATE);
+ uart_update_timeout(port, termios->c_cflag, baud);
+ spin_unlock_irqrestore(&port->lock, flags);
+}
+
+static const char *timbuart_type(struct uart_port *port)
+{
+ return port->type == PORT_UNKNOWN ? "timbuart" : NULL;
+}
+
+/* We do not request/release mappings of the registers here,
+ * currently it's done in the proble function.
+ */
+static void timbuart_release_port(struct uart_port *port)
+{
+ struct platform_device *pdev = to_platform_device(port->dev);
+ int size =
+ resource_size(platform_get_resource(pdev, IORESOURCE_MEM, 0));
+
+ if (port->flags & UPF_IOREMAP) {
+ iounmap(port->membase);
+ port->membase = NULL;
+ }
+
+ release_mem_region(port->mapbase, size);
+}
+
+static int timbuart_request_port(struct uart_port *port)
+{
+ struct platform_device *pdev = to_platform_device(port->dev);
+ int size =
+ resource_size(platform_get_resource(pdev, IORESOURCE_MEM, 0));
+
+ if (!request_mem_region(port->mapbase, size, "timb-uart"))
+ return -EBUSY;
+
+ if (port->flags & UPF_IOREMAP) {
+ port->membase = ioremap(port->mapbase, size);
+ if (port->membase == NULL) {
+ release_mem_region(port->mapbase, size);
+ return -ENOMEM;
+ }
+ }
+
+ return 0;
+}
+
+static irqreturn_t timbuart_handleinterrupt(int irq, void *devid)
+{
+ struct timbuart_port *uart = (struct timbuart_port *)devid;
+
+ if (ioread8(uart->port.membase + TIMBUART_IPR)) {
+ uart->last_ier = ioread8(uart->port.membase + TIMBUART_IER);
+
+ /* disable interrupts, the tasklet enables them again */
+ iowrite8(0, uart->port.membase + TIMBUART_IER);
+
+ /* fire off bottom half */
+ tasklet_schedule(&uart->tasklet);
+
+ return IRQ_HANDLED;
+ } else
+ return IRQ_NONE;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void timbuart_config_port(struct uart_port *port, int flags)
+{
+ if (flags & UART_CONFIG_TYPE) {
+ port->type = PORT_TIMBUART;
+ timbuart_request_port(port);
+ }
+}
+
+static int timbuart_verify_port(struct uart_port *port,
+ struct serial_struct *ser)
+{
+ /* we don't want the core code to modify any port params */
+ return -EINVAL;
+}
+
+static struct uart_ops timbuart_ops = {
+ .tx_empty = timbuart_tx_empty,
+ .set_mctrl = timbuart_set_mctrl,
+ .get_mctrl = timbuart_get_mctrl,
+ .stop_tx = timbuart_stop_tx,
+ .start_tx = timbuart_start_tx,
+ .flush_buffer = timbuart_flush_buffer,
+ .stop_rx = timbuart_stop_rx,
+ .enable_ms = timbuart_enable_ms,
+ .break_ctl = timbuart_break_ctl,
+ .startup = timbuart_startup,
+ .shutdown = timbuart_shutdown,
+ .set_termios = timbuart_set_termios,
+ .type = timbuart_type,
+ .release_port = timbuart_release_port,
+ .request_port = timbuart_request_port,
+ .config_port = timbuart_config_port,
+ .verify_port = timbuart_verify_port
+};
+
+static struct uart_driver timbuart_driver = {
+ .owner = THIS_MODULE,
+ .driver_name = "timberdale_uart",
+ .dev_name = "ttyTU",
+ .major = TIMBUART_MAJOR,
+ .minor = TIMBUART_MINOR,
+ .nr = 1
+};
+
+static int timbuart_probe(struct platform_device *dev)
+{
+ int err;
+ struct timbuart_port *uart;
+ struct resource *iomem;
+
+ dev_dbg(&dev->dev, "%s\n", __func__);
+
+ uart = kzalloc(sizeof(*uart), GFP_KERNEL);
+ if (!uart) {
+ err = -EINVAL;
+ goto err_mem;
+ }
+
+ uart->usedma = 0;
+
+ uart->port.uartclk = 3250000 * 16;
+ uart->port.fifosize = TIMBUART_FIFO_SIZE;
+ uart->port.regshift = 2;
+ uart->port.iotype = UPIO_MEM;
+ uart->port.ops = &timbuart_ops;
+ uart->port.irq = 0;
+ uart->port.flags = UPF_BOOT_AUTOCONF | UPF_IOREMAP;
+ uart->port.line = 0;
+ uart->port.dev = &dev->dev;
+
+ iomem = platform_get_resource(dev, IORESOURCE_MEM, 0);
+ if (!iomem) {
+ err = -ENOMEM;
+ goto err_register;
+ }
+ uart->port.mapbase = iomem->start;
+ uart->port.membase = NULL;
+
+ uart->port.irq = platform_get_irq(dev, 0);
+ if (uart->port.irq < 0) {
+ err = -EINVAL;
+ goto err_register;
+ }
+
+ tasklet_init(&uart->tasklet, timbuart_tasklet, (unsigned long)uart);
+
+ err = uart_register_driver(&timbuart_driver);
+ if (err)
+ goto err_register;
+
+ err = uart_add_one_port(&timbuart_driver, &uart->port);
+ if (err)
+ goto err_add_port;
+
+ platform_set_drvdata(dev, uart);
+
+ return 0;
+
+err_add_port:
+ uart_unregister_driver(&timbuart_driver);
+err_register:
+ kfree(uart);
+err_mem:
+ printk(KERN_ERR "timberdale: Failed to register Timberdale UART: %d\n",
+ err);
+
+ return err;
+}
+
+static int timbuart_remove(struct platform_device *dev)
+{
+ struct timbuart_port *uart = platform_get_drvdata(dev);
+
+ tasklet_kill(&uart->tasklet);
+ uart_remove_one_port(&timbuart_driver, &uart->port);
+ uart_unregister_driver(&timbuart_driver);
+ kfree(uart);
+
+ return 0;
+}
+
+static struct platform_driver timbuart_platform_driver = {
+ .driver = {
+ .name = "timb-uart",
+ .owner = THIS_MODULE,
+ },
+ .probe = timbuart_probe,
+ .remove = timbuart_remove,
+};
+
+/*--------------------------------------------------------------------------*/
+
+static int __init timbuart_init(void)
+{
+ return platform_driver_register(&timbuart_platform_driver);
+}
+
+static void __exit timbuart_exit(void)
+{
+ platform_driver_unregister(&timbuart_platform_driver);
+}
+
+module_init(timbuart_init);
+module_exit(timbuart_exit);
+
+MODULE_DESCRIPTION("Timberdale UART driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:timb-uart");
+
diff --git a/drivers/serial/timbuart.h b/drivers/serial/timbuart.h
new file mode 100644
index 00000000000..7e566766bc4
--- /dev/null
+++ b/drivers/serial/timbuart.h
@@ -0,0 +1,58 @@
+/*
+ * timbuart.c timberdale FPGA GPIO driver
+ * Copyright (c) 2009 Intel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+/* Supports:
+ * Timberdale FPGA UART
+ */
+
+#ifndef _TIMBUART_H
+#define _TIMBUART_H
+
+#define TIMBUART_FIFO_SIZE 2048
+
+#define TIMBUART_RXFIFO 0x08
+#define TIMBUART_TXFIFO 0x0c
+#define TIMBUART_IER 0x10
+#define TIMBUART_IPR 0x14
+#define TIMBUART_ISR 0x18
+#define TIMBUART_CTRL 0x1c
+#define TIMBUART_BAUDRATE 0x20
+
+#define TIMBUART_CTRL_RTS 0x01
+#define TIMBUART_CTRL_CTS 0x02
+#define TIMBUART_CTRL_FLSHTX 0x40
+#define TIMBUART_CTRL_FLSHRX 0x80
+
+#define TXBF 0x01
+#define TXBAE 0x02
+#define CTS_DELTA 0x04
+#define RXDP 0x08
+#define RXBAF 0x10
+#define RXBF 0x20
+#define RXTT 0x40
+#define RXBNAE 0x80
+#define TXBE 0x100
+
+#define RXFLAGS (RXDP | RXBAF | RXBF | RXTT | RXBNAE)
+#define TXFLAGS (TXBF | TXBAE)
+
+#define TIMBUART_MAJOR 204
+#define TIMBUART_MINOR 192
+
+#endif /* _TIMBUART_H */
+
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-12-19 04:50:57 +0000