diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/sh-sci.c | 100 | ||||
| -rw-r--r-- | drivers/serial/sh-sci.h | 153 |
2 files changed, 76 insertions, 177 deletions
diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index c291b3add1d..251c08c55ae 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -3,7 +3,7 @@ * * SuperH on-chip serial module support. (SCI with no FIFO / with FIFO) * - * Copyright (C) 2002 - 2008 Paul Mundt + * Copyright (C) 2002 - 2011 Paul Mundt * Modified to support SH7720 SCIF. Markus Brunner, Mark Jonas (Jul 2007). * * based off of the old drivers/char/sh-sci.c by: @@ -81,14 +81,22 @@ struct sci_port { struct timer_list break_timer; int break_flag; + /* SCSCR initialization */ + unsigned int scscr; + + /* SCBRR calculation algo */ + unsigned int scbrr_algo_id; + /* Interface clock */ struct clk *iclk; /* Function clock */ struct clk *fclk; struct list_head node; + struct dma_chan *chan_tx; struct dma_chan *chan_rx; + #ifdef CONFIG_SERIAL_SH_SCI_DMA struct device *dma_dev; unsigned int slave_tx; @@ -415,9 +423,9 @@ static void sci_transmit_chars(struct uart_port *port) if (!(status & SCxSR_TDxE(port))) { ctrl = sci_in(port, SCSCR); if (uart_circ_empty(xmit)) - ctrl &= ~SCI_CTRL_FLAGS_TIE; + ctrl &= ~SCSCR_TIE; else - ctrl |= SCI_CTRL_FLAGS_TIE; + ctrl |= SCSCR_TIE; sci_out(port, SCSCR, ctrl); return; } @@ -459,7 +467,7 @@ static void sci_transmit_chars(struct uart_port *port) sci_out(port, SCxSR, SCxSR_TDxE_CLEAR(port)); } - ctrl |= SCI_CTRL_FLAGS_TIE; + ctrl |= SCSCR_TIE; sci_out(port, SCSCR, ctrl); } } @@ -708,7 +716,7 @@ static irqreturn_t sci_rx_interrupt(int irq, void *ptr) disable_irq_nosync(irq); scr |= 0x4000; } else { - scr &= ~SCI_CTRL_FLAGS_RIE; + scr &= ~SCSCR_RIE; } sci_out(port, SCSCR, scr); /* Clear current interrupt */ @@ -777,6 +785,18 @@ static irqreturn_t sci_br_interrupt(int irq, void *ptr) return IRQ_HANDLED; } +static inline unsigned long port_rx_irq_mask(struct uart_port *port) +{ + /* + * Not all ports (such as SCIFA) will support REIE. Rather than + * special-casing the port type, we check the port initialization + * IRQ enable mask to see whether the IRQ is desired at all. If + * it's unset, it's logically inferred that there's no point in + * testing for it. + */ + return SCSCR_RIE | (to_sci_port(port)->scscr & SCSR_REIE); +} + static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr) { unsigned short ssr_status, scr_status, err_enabled; @@ -786,22 +806,25 @@ static irqreturn_t sci_mpxed_interrupt(int irq, void *ptr) ssr_status = sci_in(port, SCxSR); scr_status = sci_in(port, SCSCR); - err_enabled = scr_status & (SCI_CTRL_FLAGS_REIE | SCI_CTRL_FLAGS_RIE); + err_enabled = scr_status & port_rx_irq_mask(port); /* Tx Interrupt */ - if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCI_CTRL_FLAGS_TIE) && + if ((ssr_status & SCxSR_TDxE(port)) && (scr_status & SCSCR_TIE) && !s->chan_tx) ret = sci_tx_interrupt(irq, ptr); + /* * Rx Interrupt: if we're using DMA, the DMA controller clears RDF / * DR flags */ if (((ssr_status & SCxSR_RDxF(port)) || s->chan_rx) && - (scr_status & SCI_CTRL_FLAGS_RIE)) + (scr_status & SCSCR_RIE)) ret = sci_rx_interrupt(irq, ptr); + /* Error Interrupt */ if ((ssr_status & SCxSR_ERRORS(port)) && err_enabled) ret = sci_er_interrupt(irq, ptr); + /* Break Interrupt */ if ((ssr_status & SCxSR_BRK(port)) && err_enabled) ret = sci_br_interrupt(irq, ptr); @@ -951,7 +974,7 @@ static void sci_dma_tx_complete(void *arg) schedule_work(&s->work_tx); } else if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { u16 ctrl = sci_in(port, SCSCR); - sci_out(port, SCSCR, ctrl & ~SCI_CTRL_FLAGS_TIE); + sci_out(port, SCSCR, ctrl & ~SCSCR_TIE); } spin_unlock_irqrestore(&port->lock, flags); @@ -1214,14 +1237,16 @@ static void sci_start_tx(struct uart_port *port) if (new != scr) sci_out(port, SCSCR, new); } + if (s->chan_tx && !uart_circ_empty(&s->port.state->xmit) && s->cookie_tx < 0) schedule_work(&s->work_tx); #endif + if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) { /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */ ctrl = sci_in(port, SCSCR); - sci_out(port, SCSCR, ctrl | SCI_CTRL_FLAGS_TIE); + sci_out(port, SCSCR, ctrl | SCSCR_TIE); } } @@ -1231,20 +1256,24 @@ static void sci_stop_tx(struct uart_port *port) /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */ ctrl = sci_in(port, SCSCR); + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) ctrl &= ~0x8000; - ctrl &= ~SCI_CTRL_FLAGS_TIE; + + ctrl &= ~SCSCR_TIE; + sci_out(port, SCSCR, ctrl); } static void sci_start_rx(struct uart_port *port) { - unsigned short ctrl = SCI_CTRL_FLAGS_RIE | SCI_CTRL_FLAGS_REIE; + unsigned short ctrl; + + ctrl = sci_in(port, SCSCR) | port_rx_irq_mask(port); - /* Set RIE (Receive Interrupt Enable) bit in SCSCR */ - ctrl |= sci_in(port, SCSCR); if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) ctrl &= ~0x4000; + sci_out(port, SCSCR, ctrl); } @@ -1252,11 +1281,13 @@ static void sci_stop_rx(struct uart_port *port) { unsigned short ctrl; - /* Clear RIE (Receive Interrupt Enable) bit in SCSCR */ ctrl = sci_in(port, SCSCR); + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) ctrl &= ~0x4000; - ctrl &= ~(SCI_CTRL_FLAGS_RIE | SCI_CTRL_FLAGS_REIE); + + ctrl &= ~port_rx_irq_mask(port); + sci_out(port, SCSCR, ctrl); } @@ -1296,7 +1327,7 @@ static void rx_timer_fn(unsigned long arg) scr &= ~0x4000; enable_irq(s->irqs[1]); } - sci_out(port, SCSCR, scr | SCI_CTRL_FLAGS_RIE); + sci_out(port, SCSCR, scr | SCSCR_RIE); dev_dbg(port->dev, "DMA Rx timed out\n"); schedule_work(&s->work_rx); } @@ -1442,12 +1473,31 @@ static void sci_shutdown(struct uart_port *port) s->disable(port); } +static unsigned int sci_scbrr_calc(unsigned int algo_id, unsigned int bps, + unsigned long freq) +{ + switch (algo_id) { + case SCBRR_ALGO_1: + return ((freq + 16 * bps) / (16 * bps) - 1); + case SCBRR_ALGO_2: + return ((freq + 16 * bps) / (32 * bps) - 1); + case SCBRR_ALGO_3: + return (((freq * 2) + 16 * bps) / (16 * bps) - 1); + case SCBRR_ALGO_4: + return (((freq * 2) + 16 * bps) / (32 * bps) - 1); + case SCBRR_ALGO_5: + return (((freq * 1000 / 32) / bps) - 1); + } + + /* Warn, but use a safe default */ + WARN_ON(1); + return ((freq + 16 * bps) / (32 * bps) - 1); +} + static void sci_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { -#ifdef CONFIG_SERIAL_SH_SCI_DMA struct sci_port *s = to_sci_port(port); -#endif unsigned int status, baud, smr_val, max_baud; int t = -1; u16 scfcr = 0; @@ -1464,7 +1514,7 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios, baud = uart_get_baud_rate(port, termios, old, 0, max_baud); if (likely(baud && port->uartclk)) - t = SCBRR_VALUE(baud, port->uartclk); + t = sci_scbrr_calc(s->scbrr_algo_id, baud, port->uartclk); do { status = sci_in(port, SCxSR); @@ -1506,7 +1556,7 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios, sci_init_pins(port, termios->c_cflag); sci_out(port, SCFCR, scfcr | ((termios->c_cflag & CRTSCTS) ? SCFCR_MCE : 0)); - sci_out(port, SCSCR, SCSCR_INIT(port)); + sci_out(port, SCSCR, s->scscr); #ifdef CONFIG_SERIAL_SH_SCI_DMA /* @@ -1679,9 +1729,11 @@ static int __devinit sci_init_single(struct platform_device *dev, port->mapbase = p->mapbase; port->membase = p->membase; - port->irq = p->irqs[SCIx_TXI_IRQ]; - port->flags = p->flags; - sci_port->type = port->type = p->type; + port->irq = p->irqs[SCIx_TXI_IRQ]; + port->flags = p->flags; + sci_port->type = port->type = p->type; + sci_port->scscr = p->scscr; + sci_port->scbrr_algo_id = p->scbrr_algo_id; #ifdef CONFIG_SERIAL_SH_SCI_DMA sci_port->dma_dev = p->dma_dev; diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h index 4bc614e4221..b223d6cbf33 100644 --- a/drivers/serial/sh-sci.h +++ b/drivers/serial/sh-sci.h @@ -15,27 +15,17 @@ defined(CONFIG_CPU_SUBTYPE_SH7709) # define SCPCR 0xA4000116 /* 16 bit SCI and SCIF */ # define SCPDR 0xA4000136 /* 8 bit SCI and SCIF */ -# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7705) # define SCIF0 0xA4400000 # define SCIF2 0xA4410000 -# define SCSMR_Ir 0xA44A0000 -# define IRDA_SCIF SCIF0 # define SCPCR 0xA4000116 # define SCPDR 0xA4000136 - -/* Set the clock source, - * SCIF2 (0xA4410000) -> External clock, SCK pin used as clock input - * SCIF0 (0xA4400000) -> Internal clock, SCK pin as serial clock output - */ -# define SCSCR_INIT(port) (port->mapbase == SCIF2) ? 0xF3 : 0xF0 #elif defined(CONFIG_CPU_SUBTYPE_SH7720) || \ defined(CONFIG_CPU_SUBTYPE_SH7721) || \ defined(CONFIG_ARCH_SH73A0) || \ defined(CONFIG_ARCH_SH7367) || \ defined(CONFIG_ARCH_SH7377) || \ defined(CONFIG_ARCH_SH7372) -# define SCSCR_INIT(port) 0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */ # define PORT_PTCR 0xA405011EUL # define PORT_PVCR 0xA4050122UL # define SCIF_ORER 0x0200 /* overrun error bit */ @@ -43,7 +33,6 @@ # define SCSPTR1 0xFFE0001C /* 8 bit SCIF */ # define SCSPTR2 0xFFE80020 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7750) || \ defined(CONFIG_CPU_SUBTYPE_SH7750R) || \ defined(CONFIG_CPU_SUBTYPE_SH7750S) || \ @@ -53,39 +42,31 @@ # define SCSPTR1 0xffe0001c /* 8 bit SCI */ # define SCSPTR2 0xFFE80020 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) (((port)->type == PORT_SCI) ? \ - 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */ : \ - 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ ) #elif defined(CONFIG_CPU_SUBTYPE_SH7760) # define SCSPTR0 0xfe600024 /* 16 bit SCIF */ # define SCSPTR1 0xfe610024 /* 16 bit SCIF */ # define SCSPTR2 0xfe620024 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712) # define SCSPTR0 0xA4400000 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* overrun error bit */ # define PACR 0xa4050100 # define PBCR 0xa4050102 -# define SCSCR_INIT(port) 0x3B #elif defined(CONFIG_CPU_SUBTYPE_SH7343) # define SCSPTR0 0xffe00010 /* 16 bit SCIF */ # define SCSPTR1 0xffe10010 /* 16 bit SCIF */ # define SCSPTR2 0xffe20010 /* 16 bit SCIF */ # define SCSPTR3 0xffe30010 /* 16 bit SCIF */ -# define SCSCR_INIT(port) 0x32 /* TIE=0,RIE=0,TE=1,RE=1,REIE=0,CKE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7722) # define PADR 0xA4050120 # define PSDR 0xA405013e # define PWDR 0xA4050166 # define PSCR 0xA405011E # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7366) # define SCPDR0 0xA405013E /* 16 bit SCIF0 PSDR */ # define SCSPTR0 SCPDR0 # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7723) # define SCSPTR0 0xa4050160 # define SCSPTR1 0xa405013e @@ -94,62 +75,38 @@ # define SCSPTR4 0xa4050128 # define SCSPTR5 0xa4050128 # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x0038 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7724) # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) ((port)->type == PORT_SCIFA ? \ - 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */ : \ - 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ ) #elif defined(CONFIG_CPU_SUBTYPE_SH4_202) # define SCSPTR2 0xffe80020 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH5_101) || defined(CONFIG_CPU_SUBTYPE_SH5_103) -# define SCIF_BASE_ADDR 0x01030000 -# define SCIF_ADDR_SH5 PHYS_PERIPHERAL_BLOCK+SCIF_BASE_ADDR # define SCIF_PTR2_OFFS 0x0000020 -# define SCIF_LSR2_OFFS 0x0000024 # define SCSPTR2 ((port->mapbase)+SCIF_PTR2_OFFS) /* 16 bit SCIF */ -# define SCLSR2 ((port->mapbase)+SCIF_LSR2_OFFS) /* 16 bit SCIF */ -# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0, TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_H83007) || defined(CONFIG_H83068) -# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */ # define H8300_SCI_DR(ch) *(volatile char *)(P1DR + h8300_sci_pins[ch].port) #elif defined(CONFIG_H8S2678) -# define SCSCR_INIT(port) 0x30 /* TIE=0,RIE=0,TE=1,RE=1 */ # define H8300_SCI_DR(ch) *(volatile char *)(P1DR + h8300_sci_pins[ch].port) #elif defined(CONFIG_CPU_SUBTYPE_SH7757) # define SCSPTR0 0xfe4b0020 # define SCSPTR1 0xfe4b0020 # define SCSPTR2 0xfe4b0020 # define SCIF_ORER 0x0001 -# define SCSCR_INIT(port) 0x38 # define SCIF_ONLY #elif defined(CONFIG_CPU_SUBTYPE_SH7763) # define SCSPTR0 0xffe00024 /* 16 bit SCIF */ # define SCSPTR1 0xffe08024 /* 16 bit SCIF */ # define SCSPTR2 0xffe10020 /* 16 bit SCIF/IRDA */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7770) # define SCSPTR0 0xff923020 /* 16 bit SCIF */ # define SCSPTR1 0xff924020 /* 16 bit SCIF */ # define SCSPTR2 0xff925020 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x3c /* TIE=0,RIE=0,TE=1,RE=1,REIE=1,cke=2 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7780) # define SCSPTR0 0xffe00024 /* 16 bit SCIF */ # define SCSPTR1 0xffe10024 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* Overrun error bit */ - -#if defined(CONFIG_SH_SH2007) -/* TIE=0,RIE=0,TE=1,RE=1,REIE=1,CKE1=0 */ -# define SCSCR_INIT(port) 0x38 -#else -/* TIE=0,RIE=0,TE=1,RE=1,REIE=1,CKE1=1 */ -# define SCSCR_INIT(port) 0x3a -#endif - #elif defined(CONFIG_CPU_SUBTYPE_SH7785) || \ defined(CONFIG_CPU_SUBTYPE_SH7786) # define SCSPTR0 0xffea0024 /* 16 bit SCIF */ @@ -159,7 +116,6 @@ # define SCSPTR4 0xffee0024 /* 16 bit SCIF */ # define SCSPTR5 0xffef0024 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* Overrun error bit */ -# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7201) || \ defined(CONFIG_CPU_SUBTYPE_SH7203) || \ defined(CONFIG_CPU_SUBTYPE_SH7206) || \ @@ -174,52 +130,21 @@ # define SCSPTR6 0xfffeB020 /* 16 bit SCIF */ # define SCSPTR7 0xfffeB820 /* 16 bit SCIF */ # endif -# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SH7619) # define SCSPTR0 0xf8400020 /* 16 bit SCIF */ # define SCSPTR1 0xf8410020 /* 16 bit SCIF */ # define SCSPTR2 0xf8420020 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* overrun error bit */ -# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #elif defined(CONFIG_CPU_SUBTYPE_SHX3) # define SCSPTR0 0xffc30020 /* 16 bit SCIF */ # define SCSPTR1 0xffc40020 /* 16 bit SCIF */ # define SCSPTR2 0xffc50020 /* 16 bit SCIF */ # define SCSPTR3 0xffc60020 /* 16 bit SCIF */ # define SCIF_ORER 0x0001 /* Overrun error bit */ -# define SCSCR_INIT(port) 0x38 /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */ #else # error CPU subtype not defined #endif -/* SCSCR */ -#define SCI_CTRL_FLAGS_TIE 0x80 /* all */ -#define SCI_CTRL_FLAGS_RIE 0x40 /* all */ -#define SCI_CTRL_FLAGS_TE 0x20 /* all */ -#define SCI_CTRL_FLAGS_RE 0x10 /* all */ -#if defined(CONFIG_CPU_SUBTYPE_SH7750) || \ - defined(CONFIG_CPU_SUBTYPE_SH7091) || \ - defined(CONFIG_CPU_SUBTYPE_SH7750R) || \ - defined(CONFIG_CPU_SUBTYPE_SH7722) || \ - defined(CONFIG_CPU_SUBTYPE_SH7750S) || \ - defined(CONFIG_CPU_SUBTYPE_SH7751) || \ - defined(CONFIG_CPU_SUBTYPE_SH7751R) || \ - defined(CONFIG_CPU_SUBTYPE_SH7763) || \ - defined(CONFIG_CPU_SUBTYPE_SH7780) || \ - defined(CONFIG_CPU_SUBTYPE_SH7785) || \ - defined(CONFIG_CPU_SUBTYPE_SH7786) || \ - defined(CONFIG_CPU_SUBTYPE_SHX3) -#define SCI_CTRL_FLAGS_REIE 0x08 /* 7750 SCIF */ -#elif defined(CONFIG_CPU_SUBTYPE_SH7724) -#define SCI_CTRL_FLAGS_REIE ((port)->type == PORT_SCIFA ? 0 : 8) -#else -#define SCI_CTRL_FLAGS_REIE 0 -#endif -/* SCI_CTRL_FLAGS_MPIE 0x08 * 7707 SCI, 7708 SCI, 7709 SCI, 7750 SCI */ -/* SCI_CTRL_FLAGS_TEIE 0x04 * 7707 SCI, 7708 SCI, 7709 SCI, 7750 SCI */ -/* SCI_CTRL_FLAGS_CKE1 0x02 * all */ -/* SCI_CTRL_FLAGS_CKE0 0x01 * 7707 SCI/SCIF, 7708 SCI, 7709 SCI/SCIF, 7750 SCI */ - /* SCxSR SCI */ #define SCI_TDRE 0x80 /* 7707 SCI, 7708 SCI, 7709 SCI, 7750 SCI */ #define SCI_RDRF 0x40 /* 7707 SCI, 7708 SCI, 7709 SCI, 7750 SCI */ @@ -300,23 +225,11 @@ /* SCFCR */ #define SCFCR_RFRST 0x0002 #define SCFCR_TFRST 0x0004 -#define SCFCR_TCRST 0x4000 #define SCFCR_MCE 0x0008 #define SCI_MAJOR 204 #define SCI_MINOR_START 8 -/* Generic serial flags */ -#define SCI_RX_THROTTLE 0x0000001 - -#define SCI_MAGIC 0xbabeface - -/* - * Events are used to schedule things to happen at timer-interrupt - * time, instead of at rs interrupt time. - */ -#define SCI_EVENT_WRITE_WAKEUP 0 - #define SCI_IN(size, offset) \ if ((size) == 8) { \ return ioread8(port->membase + (offset)); \ @@ -445,8 +358,6 @@ SCIF_FNS(SCSMR, 0x00, 16) SCIF_FNS(SCBRR, 0x04, 8) SCIF_FNS(SCSCR, 0x08, 16) -SCIF_FNS(SCTDSR, 0x0c, 8) -SCIF_FNS(SCFER, 0x10, 16) SCIF_FNS(SCxSR, 0x14, 16) SCIF_FNS(SCFCR, 0x18, 16) SCIF_FNS(SCFDR, 0x1c, 16) @@ -476,8 +387,6 @@ SCIx_FNS(SCxTDR, 0x20, 8, 0x0c, 8) SCIx_FNS(SCxSR, 0x14, 16, 0x10, 16) SCIx_FNS(SCxRDR, 0x24, 8, 0x14, 8) SCIx_FNS(SCSPTR, 0, 0, 0, 0) -SCIF_FNS(SCTDSR, 0x0c, 8) -SCIF_FNS(SCFER, 0x10, 16) SCIF_FNS(SCFCR, 0x18, 16) SCIF_FNS(SCFDR, 0x1c, 16) SCIF_FNS(SCLSR, 0x24, 16) @@ -503,7 +412,6 @@ SCIF_FNS(SCLSR, 0, 0, 0x28, 16) #elif defined(CONFIG_CPU_SUBTYPE_SH7763) SCIF_FNS(SCFDR, 0, 0, 0x1C, 16) SCIF_FNS(SCSPTR2, 0, 0, 0x20, 16) -SCIF_FNS(SCLSR2, 0, 0, 0x24, 16) SCIF_FNS(SCTFDR, 0x0e, 16, 0x1C, 16) SCIF_FNS(SCRFDR, 0x0e, 16, 0x20, 16) SCIF_FNS(SCSPTR, 0, 0, 0x24, 16) @@ -597,64 +505,3 @@ static inline int sci_rxd_in(struct uart_port *port) return 1; } #endif - -/* - * Values for the BitRate Register (SCBRR) - * - * The values are actually divisors for a frequency which can - * be internal to the SH3 (14.7456MHz) or derived from an external - * clock source. This driver assumes the internal clock is used; - * to support using an external clock source, config options or - * possibly command-line options would need to be added. - * - * Also, to support speeds below 2400 (why?) the lower 2 bits of - * the SCSMR register would also need to be set to non-zero values. - * - * -- Greg Banks 27Feb2000 - * - * Answer: The SCBRR register is only eight bits, and the value in - * it gets larger with lower baud rates. At around 2400 (depending on - * the peripherial module clock) you run out of bits. However the - * lower two bits of SCSMR allow the module clock to be divided down, - * scaling the value which is needed in SCBRR. - * - * -- Stuart Menefy - 23 May 2000 - * - * I meant, why would anyone bother with bitrates below 2400. - * - * -- Greg Banks - 7Jul2000 - * - * You "speedist"! How will I use my 110bps ASR-33 teletype with paper - * tape reader as a console! - * - * -- Mitch Davis - 15 Jul 2000 - */ - -#if (defined(CONFIG_CPU_SUBTYPE_SH7780) || \ - defined(CONFIG_CPU_SUBTYPE_SH7785) || \ - defined(CONFIG_CPU_SUBTYPE_SH7786)) && \ - !defined(CONFIG_SH_SH2007) -#define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(16*bps)-1) -#elif defined(CONFIG_CPU_SUBTYPE_SH7705) || \ - defined(CONFIG_CPU_SUBTYPE_SH7720) || \ - defined(CONFIG_CPU_SUBTYPE_SH7721) || \ - defined(CONFIG_ARCH_SH73A0) || \ - defined(CONFIG_ARCH_SH7367) || \ - defined(CONFIG_ARCH_SH7377) || \ - defined(CONFIG_ARCH_SH7372) -#define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1) -#elif defined(CONFIG_CPU_SUBTYPE_SH7723) ||\ - defined(CONFIG_CPU_SUBTYPE_SH7724) -static inline int scbrr_calc(struct uart_port *port, int bps, int clk) -{ - if (port->type == PORT_SCIF) - return (clk+16*bps)/(32*bps)-1; - else - return ((clk*2)+16*bps)/(16*bps)-1; -} -#define SCBRR_VALUE(bps, clk) scbrr_calc(port, bps, clk) -#elif defined(__H8300H__) || defined(__H8300S__) -#define SCBRR_VALUE(bps, clk) (((clk*1000/32)/bps)-1) -#else /* Generic SH */ -#define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(32*bps)-1) -#endif |