summaryrefslogtreecommitdiffstats
path: root/drivers/serial
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/serial')
-rw-r--r--drivers/serial/8250.c125
-rw-r--r--drivers/serial/Kconfig117
-rw-r--r--drivers/serial/Makefile1
-rw-r--r--drivers/serial/amba-pl010.c295
-rw-r--r--drivers/serial/atmel_serial.c9
-rw-r--r--drivers/serial/atmel_serial.h3
-rw-r--r--drivers/serial/bfin_5xx.c1012
-rw-r--r--drivers/serial/cpm_uart/cpm_uart_core.c12
-rw-r--r--drivers/serial/crisv10.h136
-rw-r--r--drivers/serial/icom.c1
-rw-r--r--drivers/serial/imx.c268
-rw-r--r--drivers/serial/jsm/jsm_neo.c7
-rw-r--r--drivers/serial/jsm/jsm_tty.c1
-rw-r--r--drivers/serial/mpc52xx_uart.c7
-rw-r--r--drivers/serial/mpsc.c25
-rw-r--r--drivers/serial/of_serial.c7
-rw-r--r--drivers/serial/pmac_zilog.c12
-rw-r--r--drivers/serial/pxa.c8
-rw-r--r--drivers/serial/s3c2410.c6
-rw-r--r--drivers/serial/serial_core.c41
-rw-r--r--drivers/serial/serial_txx9.c32
-rw-r--r--drivers/serial/sh-sci.c113
-rw-r--r--drivers/serial/sh-sci.h83
-rw-r--r--drivers/serial/sunsu.c12
24 files changed, 1859 insertions, 474 deletions
diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c
index 90621c3312b..48e259a0167 100644
--- a/drivers/serial/8250.c
+++ b/drivers/serial/8250.c
@@ -251,9 +251,16 @@ static const struct serial8250_config uart_config[] = {
.fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
.flags = UART_CAP_FIFO | UART_CAP_UUE,
},
+ [PORT_RM9000] = {
+ .name = "RM9000",
+ .fifo_size = 16,
+ .tx_loadsz = 16,
+ .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10,
+ .flags = UART_CAP_FIFO,
+ },
};
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined (CONFIG_SERIAL_8250_AU1X00)
/* Au1x00 UART hardware has a weird register layout */
static const u8 au_io_in_map[] = {
@@ -289,6 +296,44 @@ static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
return au_io_out_map[offset];
}
+#elif defined (CONFIG_SERIAL_8250_RM9K)
+
+static const u8
+ regmap_in[8] = {
+ [UART_RX] = 0x00,
+ [UART_IER] = 0x0c,
+ [UART_IIR] = 0x14,
+ [UART_LCR] = 0x1c,
+ [UART_MCR] = 0x20,
+ [UART_LSR] = 0x24,
+ [UART_MSR] = 0x28,
+ [UART_SCR] = 0x2c
+ },
+ regmap_out[8] = {
+ [UART_TX] = 0x04,
+ [UART_IER] = 0x0c,
+ [UART_FCR] = 0x18,
+ [UART_LCR] = 0x1c,
+ [UART_MCR] = 0x20,
+ [UART_LSR] = 0x24,
+ [UART_MSR] = 0x28,
+ [UART_SCR] = 0x2c
+ };
+
+static inline int map_8250_in_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_RM9000)
+ return offset;
+ return regmap_in[offset];
+}
+
+static inline int map_8250_out_reg(struct uart_8250_port *up, int offset)
+{
+ if (up->port.iotype != UPIO_RM9000)
+ return offset;
+ return regmap_out[offset];
+}
+
#else
/* sane hardware needs no mapping */
@@ -308,8 +353,10 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset)
return inb(up->port.iobase + 1);
case UPIO_MEM:
+ case UPIO_DWAPB:
return readb(up->port.membase + offset);
+ case UPIO_RM9000:
case UPIO_MEM32:
return readl(up->port.membase + offset);
@@ -333,6 +380,8 @@ static unsigned int serial_in(struct uart_8250_port *up, int offset)
static void
serial_out(struct uart_8250_port *up, int offset, int value)
{
+ /* Save the offset before it's remapped */
+ int save_offset = offset;
offset = map_8250_out_reg(up, offset) << up->port.regshift;
switch (up->port.iotype) {
@@ -345,6 +394,7 @@ serial_out(struct uart_8250_port *up, int offset, int value)
writeb(value, up->port.membase + offset);
break;
+ case UPIO_RM9000:
case UPIO_MEM32:
writel(value, up->port.membase + offset);
break;
@@ -359,6 +409,18 @@ serial_out(struct uart_8250_port *up, int offset, int value)
writeb(value, up->port.membase + offset);
break;
+ case UPIO_DWAPB:
+ /* Save the LCR value so it can be re-written when a
+ * Busy Detect interrupt occurs. */
+ if (save_offset == UART_LCR)
+ up->lcr = value;
+ writeb(value, up->port.membase + offset);
+ /* Read the IER to ensure any interrupt is cleared before
+ * returning from ISR. */
+ if (save_offset == UART_TX || save_offset == UART_IER)
+ value = serial_in(up, UART_IER);
+ break;
+
default:
outb(value, up->port.iobase + offset);
}
@@ -373,6 +435,7 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value)
#ifdef CONFIG_SERIAL_8250_AU1X00
case UPIO_AU:
#endif
+ case UPIO_DWAPB:
serial_out(up, offset, value);
serial_in(up, UART_LCR); /* safe, no side-effects */
break;
@@ -403,7 +466,7 @@ static inline void _serial_dl_write(struct uart_8250_port *up, int value)
serial_outp(up, UART_DLM, value >> 8 & 0xff);
}
-#ifdef CONFIG_SERIAL_8250_AU1X00
+#if defined (CONFIG_SERIAL_8250_AU1X00)
/* Au1x00 haven't got a standard divisor latch */
static int serial_dl_read(struct uart_8250_port *up)
{
@@ -420,6 +483,24 @@ static void serial_dl_write(struct uart_8250_port *up, int value)
else
_serial_dl_write(up, value);
}
+#elif defined (CONFIG_SERIAL_8250_RM9K)
+static int serial_dl_read(struct uart_8250_port *up)
+{
+ return (up->port.iotype == UPIO_RM9000) ?
+ (((__raw_readl(up->port.membase + 0x10) << 8) |
+ (__raw_readl(up->port.membase + 0x08) & 0xff)) & 0xffff) :
+ _serial_dl_read(up);
+}
+
+static void serial_dl_write(struct uart_8250_port *up, int value)
+{
+ if (up->port.iotype == UPIO_RM9000) {
+ __raw_writel(value, up->port.membase + 0x08);
+ __raw_writel(value >> 8, up->port.membase + 0x10);
+ } else {
+ _serial_dl_write(up, value);
+ }
+}
#else
#define serial_dl_read(up) _serial_dl_read(up)
#define serial_dl_write(up, value) _serial_dl_write(up, value)
@@ -621,7 +702,7 @@ static unsigned int autoconfig_read_divisor_id(struct uart_8250_port *p)
* its clones. (We treat the broken original StarTech 16650 V1 as a
* 16550, and why not? Startech doesn't seem to even acknowledge its
* existence.)
- *
+ *
* What evil have men's minds wrought...
*/
static void autoconfig_has_efr(struct uart_8250_port *up)
@@ -674,7 +755,7 @@ static void autoconfig_has_efr(struct uart_8250_port *up)
up->bugs |= UART_BUG_QUOT;
return;
}
-
+
/*
* We check for a XR16C850 by setting DLL and DLM to 0, and then
* reading back DLL and DLM. The chip type depends on the DLM
@@ -817,7 +898,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
status1 &= ~0xB0; /* Disable LOCK, mask out PRESL[01] */
status1 |= 0x10; /* 1.625 divisor for baud_base --> 921600 */
serial_outp(up, 0x04, status1);
-
+
serial_dl_write(up, quot);
serial_outp(up, UART_LCR, 0);
@@ -913,7 +994,6 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
* be frobbing the chips IRQ enable register to see if it exists.
*/
spin_lock_irqsave(&up->port.lock, flags);
-// save_flags(flags); cli();
up->capabilities = 0;
up->bugs = 0;
@@ -922,7 +1002,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
/*
* Do a simple existence test first; if we fail this,
* there's no point trying anything else.
- *
+ *
* 0x80 is used as a nonsense port to prevent against
* false positives due to ISA bus float. The
* assumption is that 0x80 is a non-existent port;
@@ -961,7 +1041,7 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
save_mcr = serial_in(up, UART_MCR);
save_lcr = serial_in(up, UART_LCR);
- /*
+ /*
* Check to see if a UART is really there. Certain broken
* internal modems based on the Rockwell chipset fail this
* test, because they apparently don't implement the loopback
@@ -1068,9 +1148,8 @@ static void autoconfig(struct uart_8250_port *up, unsigned int probeflags)
else
serial_outp(up, UART_IER, 0);
- out:
+ out:
spin_unlock_irqrestore(&up->port.lock, flags);
-// restore_flags(flags);
DEBUG_AUTOCONF("type=%s\n", uart_config[up->port.type].name);
}
@@ -1094,7 +1173,7 @@ static void autoconfig_irq(struct uart_8250_port *up)
save_mcr = serial_inp(up, UART_MCR);
save_ier = serial_inp(up, UART_IER);
serial_outp(up, UART_MCR, UART_MCR_OUT1 | UART_MCR_OUT2);
-
+
irqs = probe_irq_on();
serial_outp(up, UART_MCR, 0);
udelay (10);
@@ -1159,8 +1238,11 @@ static void serial8250_start_tx(struct uart_port *port)
if (up->bugs & UART_BUG_TXEN) {
unsigned char lsr, iir;
lsr = serial_in(up, UART_LSR);
- iir = serial_in(up, UART_IIR);
- if (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT)
+ iir = serial_in(up, UART_IIR) & 0x0f;
+ if ((up->port.type == PORT_RM9000) ?
+ (lsr & UART_LSR_THRE &&
+ (iir == UART_IIR_NO_INT || iir == UART_IIR_THRI)) :
+ (lsr & UART_LSR_TEMT && iir & UART_IIR_NO_INT))
transmit_chars(up);
}
}
@@ -1389,6 +1471,19 @@ static irqreturn_t serial8250_interrupt(int irq, void *dev_id)
handled = 1;
end = NULL;
+ } else if (up->port.iotype == UPIO_DWAPB &&
+ (iir & UART_IIR_BUSY) == UART_IIR_BUSY) {
+ /* The DesignWare APB UART has an Busy Detect (0x07)
+ * interrupt meaning an LCR write attempt occured while the
+ * UART was busy. The interrupt must be cleared by reading
+ * the UART status register (USR) and the LCR re-written. */
+ unsigned int status;
+ status = *(volatile u32 *)up->port.private_data;
+ serial_out(up, UART_LCR, up->lcr);
+
+ handled = 1;
+
+ end = NULL;
} else if (end == NULL)
end = l;
@@ -1928,7 +2023,7 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios,
/*
* Ask the core to calculate the divisor for us.
*/
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = serial8250_get_divisor(port, baud);
/*
@@ -2090,6 +2185,7 @@ static int serial8250_request_std_resource(struct uart_8250_port *up)
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
+ case UPIO_DWAPB:
if (!up->port.mapbase)
break;
@@ -2127,6 +2223,7 @@ static void serial8250_release_std_resource(struct uart_8250_port *up)
case UPIO_TSI:
case UPIO_MEM32:
case UPIO_MEM:
+ case UPIO_DWAPB:
if (!up->port.mapbase)
break;
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig
index ad9f321968e..e8efe938c4e 100644
--- a/drivers/serial/Kconfig
+++ b/drivers/serial/Kconfig
@@ -73,17 +73,21 @@ config SERIAL_8250_PCI
depends on SERIAL_8250 && PCI
default SERIAL_8250
help
- This builds standard PCI serial support. You may be able to
- disable this feature if you only need legacy serial support.
- Saves about 9K.
+ Say Y here if you have PCI serial ports.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8250_pci.
config SERIAL_8250_PNP
tristate "8250/16550 PNP device support" if EMBEDDED
depends on SERIAL_8250 && PNP
default SERIAL_8250
help
- This builds standard PNP serial support. You may be able to
- disable this feature if you only need legacy serial support.
+ Say Y here if you have serial ports described by PNPBIOS or ACPI.
+ These are typically ports built into the system board.
+
+ To compile this driver as a module, choose M here: the module
+ will be called 8250_pnp.
config SERIAL_8250_HP300
tristate
@@ -254,6 +258,15 @@ config SERIAL_8250_AU1X00
to this option. The driver can handle 1 or 2 serial ports.
If unsure, say N.
+config SERIAL_8250_RM9K
+ bool "Support for MIPS RM9xxx integrated serial port"
+ depends on SERIAL_8250 != n && SERIAL_RM9000
+ select SERIAL_8250_SHARE_IRQ
+ help
+ Selecting this option will add support for the integrated serial
+ port hardware found on MIPS RM9122 and similar processors.
+ If unsure, say N.
+
comment "Non-8250 serial port support"
config SERIAL_AMBA_PL010
@@ -499,6 +512,100 @@ config SERIAL_SA1100_CONSOLE
your boot loader (lilo or loadlin) about how to pass options to the
kernel at boot time.)
+config SERIAL_BFIN
+ tristate "Blackfin serial port support"
+ depends on BFIN
+ select SERIAL_CORE
+ select SERIAL_BFIN_UART0 if (BF531 || BF532 || BF533 || BF561)
+ help
+ Add support for the built-in UARTs on the Blackfin.
+
+ To compile this driver as a module, choose M here: the
+ module will be called bfin_5xx.
+
+config SERIAL_BFIN_CONSOLE
+ bool "Console on Blackfin serial port"
+ depends on SERIAL_BFIN
+ select SERIAL_CORE_CONSOLE
+
+choice
+ prompt "UART Mode"
+ depends on SERIAL_BFIN
+ default SERIAL_BFIN_DMA
+ help
+ This driver supports the built-in serial ports of the Blackfin family
+ of CPUs
+
+config SERIAL_BFIN_DMA
+ bool "DMA mode"
+ depends on DMA_UNCACHED_1M
+ help
+ This driver works under DMA mode. If this option is selected, the
+ blackfin simple dma driver is also enabled.
+
+config SERIAL_BFIN_PIO
+ bool "PIO mode"
+ help
+ This driver works under PIO mode.
+
+endchoice
+
+config SERIAL_BFIN_UART0
+ bool "Enable UART0"
+ depends on SERIAL_BFIN
+ help
+ Enable UART0
+
+config BFIN_UART0_CTSRTS
+ bool "Enable UART0 hardware flow control"
+ depends on SERIAL_BFIN_UART0
+ help
+ Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+ signal.
+
+config UART0_CTS_PIN
+ int "UART0 CTS pin"
+ depends on BFIN_UART0_CTSRTS
+ default 23
+ help
+ The default pin is GPIO_GP7.
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART0_RTS_PIN
+ int "UART0 RTS pin"
+ depends on BFIN_UART0_CTSRTS
+ default 22
+ help
+ The default pin is GPIO_GP6.
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config SERIAL_BFIN_UART1
+ bool "Enable UART1"
+ depends on SERIAL_BFIN && (BF534 || BF536 || BF537)
+ help
+ Enable UART1
+
+config BFIN_UART1_CTSRTS
+ bool "Enable UART1 hardware flow control"
+ depends on SERIAL_BFIN_UART1
+ help
+ Enable hardware flow control in the driver. Using GPIO emulate the CTS/RTS
+ signal.
+
+config UART1_CTS_PIN
+ int "UART1 CTS pin"
+ depends on BFIN_UART1_CTSRTS
+ default -1
+ help
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
+config UART1_RTS_PIN
+ int "UART1 RTS pin"
+ depends on BFIN_UART1_CTSRTS
+ default -1
+ help
+ Refer to ./include/asm-blackfin/gpio.h to see the GPIO map.
+
config SERIAL_IMX
bool "IMX serial port support"
depends on ARM && ARCH_IMX
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 6b3560c5749..4959bcb8d1e 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -27,6 +27,7 @@ obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o
obj-$(CONFIG_SERIAL_PXA) += pxa.o
obj-$(CONFIG_SERIAL_PNX8XXX) += pnx8xxx_uart.o
obj-$(CONFIG_SERIAL_SA1100) += sa1100.o
+obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
obj-$(CONFIG_SERIAL_SUNCORE) += suncore.o
obj-$(CONFIG_SERIAL_SUNHV) += sunhv.o
diff --git a/drivers/serial/amba-pl010.c b/drivers/serial/amba-pl010.c
index f69bd097166..1a9a24b8263 100644
--- a/drivers/serial/amba-pl010.c
+++ b/drivers/serial/amba-pl010.c
@@ -48,6 +48,7 @@
#include <linux/serial.h>
#include <linux/amba/bus.h>
#include <linux/amba/serial.h>
+#include <linux/clk.h>
#include <asm/io.h>
@@ -70,6 +71,7 @@
*/
struct uart_amba_port {
struct uart_port port;
+ struct clk *clk;
struct amba_device *dev;
struct amba_pl010_data *data;
unsigned int old_status;
@@ -77,73 +79,77 @@ struct uart_amba_port {
static void pl010_stop_tx(struct uart_port *port)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(port->membase + UART010_CR);
+ cr = readb(uap->port.membase + UART010_CR);
cr &= ~UART010_CR_TIE;
- writel(cr, port->membase + UART010_CR);
+ writel(cr, uap->port.membase + UART010_CR);
}
static void pl010_start_tx(struct uart_port *port)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(port->membase + UART010_CR);
+ cr = readb(uap->port.membase + UART010_CR);
cr |= UART010_CR_TIE;
- writel(cr, port->membase + UART010_CR);
+ writel(cr, uap->port.membase + UART010_CR);
}
static void pl010_stop_rx(struct uart_port *port)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(port->membase + UART010_CR);
+ cr = readb(uap->port.membase + UART010_CR);
cr &= ~(UART010_CR_RIE | UART010_CR_RTIE);
- writel(cr, port->membase + UART010_CR);
+ writel(cr, uap->port.membase + UART010_CR);
}
static void pl010_enable_ms(struct uart_port *port)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int cr;
- cr = readb(port->membase + UART010_CR);
+ cr = readb(uap->port.membase + UART010_CR);
cr |= UART010_CR_MSIE;
- writel(cr, port->membase + UART010_CR);
+ writel(cr, uap->port.membase + UART010_CR);
}
-static void pl010_rx_chars(struct uart_port *port)
+static void pl010_rx_chars(struct uart_amba_port *uap)
{
- struct tty_struct *tty = port->info->tty;
+ struct tty_struct *tty = uap->port.info->tty;
unsigned int status, ch, flag, rsr, max_count = 256;
- status = readb(port->membase + UART01x_FR);
+ status = readb(uap->port.membase + UART01x_FR);
while (UART_RX_DATA(status) && max_count--) {
- ch = readb(port->membase + UART01x_DR);
+ ch = readb(uap->port.membase + UART01x_DR);
flag = TTY_NORMAL;
- port->icount.rx++;
+ uap->port.icount.rx++;
/*
* Note that the error handling code is
* out of the main execution path
*/
- rsr = readb(port->membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
+ rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX;
if (unlikely(rsr & UART01x_RSR_ANY)) {
- writel(0, port->membase + UART01x_ECR);
+ writel(0, uap->port.membase + UART01x_ECR);
if (rsr & UART01x_RSR_BE) {
rsr &= ~(UART01x_RSR_FE | UART01x_RSR_PE);
- port->icount.brk++;
- if (uart_handle_break(port))
+ uap->port.icount.brk++;
+ if (uart_handle_break(&uap->port))
goto ignore_char;
} else if (rsr & UART01x_RSR_PE)
- port->icount.parity++;
+ uap->port.icount.parity++;
else if (rsr & UART01x_RSR_FE)
- port->icount.frame++;
+ uap->port.icount.frame++;
if (rsr & UART01x_RSR_OE)
- port->icount.overrun++;
+ uap->port.icount.overrun++;
- rsr &= port->read_status_mask;
+ rsr &= uap->port.read_status_mask;
if (rsr & UART01x_RSR_BE)
flag = TTY_BREAK;
@@ -153,53 +159,52 @@ static void pl010_rx_chars(struct uart_port *port)
flag = TTY_FRAME;
}
- if (uart_handle_sysrq_char(port, ch))
+ if (uart_handle_sysrq_char(&uap->port, ch))
goto ignore_char;
- uart_insert_char(port, rsr, UART01x_RSR_OE, ch, flag);
+ uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag);
ignore_char:
- status = readb(port->membase + UART01x_FR);
+ status = readb(uap->port.membase + UART01x_FR);
}
tty_flip_buffer_push(tty);
return;
}
-static void pl010_tx_chars(struct uart_port *port)
+static void pl010_tx_chars(struct uart_amba_port *uap)
{
- struct circ_buf *xmit = &port->info->xmit;
+ struct circ_buf *xmit = &uap->port.info->xmit;
int count;
- if (port->x_char) {
- writel(port->x_char, port->membase + UART01x_DR);
- port->icount.tx++;
- port->x_char = 0;
+ if (uap->port.x_char) {
+ writel(uap->port.x_char, uap->port.membase + UART01x_DR);
+ uap->port.icount.tx++;
+ uap->port.x_char = 0;
return;
}
- if (uart_circ_empty(xmit) || uart_tx_stopped(port)) {
- pl010_stop_tx(port);
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&uap->port)) {
+ pl010_stop_tx(&uap->port);
return;
}
- count = port->fifosize >> 1;
+ count = uap->port.fifosize >> 1;
do {
- writel(xmit->buf[xmit->tail], port->membase + UART01x_DR);
+ writel(xmit->buf[xmit->tail], uap->port.membase + UART01x_DR);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
- port->icount.tx++;
+ uap->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
- uart_write_wakeup(port);
+ uart_write_wakeup(&uap->port);
if (uart_circ_empty(xmit))
- pl010_stop_tx(port);
+ pl010_stop_tx(&uap->port);
}
-static void pl010_modem_status(struct uart_port *port)
+static void pl010_modem_status(struct uart_amba_port *uap)
{
- struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int status, delta;
writel(0, uap->port.membase + UART010_ICR);
@@ -226,47 +231,50 @@ static void pl010_modem_status(struct uart_port *port)
static irqreturn_t pl010_int(int irq, void *dev_id)
{
- struct uart_port *port = dev_id;
+ struct uart_amba_port *uap = dev_id;
unsigned int status, pass_counter = AMBA_ISR_PASS_LIMIT;
int handled = 0;
- spin_lock(&port->lock);
+ spin_lock(&uap->port.lock);
- status = readb(port->membase + UART010_IIR);
+ status = readb(uap->port.membase + UART010_IIR);
if (status) {
do {
if (status & (UART010_IIR_RTIS | UART010_IIR_RIS))
- pl010_rx_chars(port);
+ pl010_rx_chars(uap);
if (status & UART010_IIR_MIS)
- pl010_modem_status(port);
+ pl010_modem_status(uap);
if (status & UART010_IIR_TIS)
- pl010_tx_chars(port);
+ pl010_tx_chars(uap);
if (pass_counter-- == 0)
break;
- status = readb(port->membase + UART010_IIR);
+ status = readb(uap->port.membase + UART010_IIR);
} while (status & (UART010_IIR_RTIS | UART010_IIR_RIS |
UART010_IIR_TIS));
handled = 1;
}
- spin_unlock(&port->lock);
+ spin_unlock(&uap->port.lock);
return IRQ_RETVAL(handled);
}
static unsigned int pl010_tx_empty(struct uart_port *port)
{
- return readb(port->membase + UART01x_FR) & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+ unsigned int status = readb(uap->port.membase + UART01x_FR);
+ return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT;
}
static unsigned int pl010_get_mctrl(struct uart_port *port)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int result = 0;
unsigned int status;
- status = readb(port->membase + UART01x_FR);
+ status = readb(uap->port.membase + UART01x_FR);
if (status & UART01x_FR_DCD)
result |= TIOCM_CAR;
if (status & UART01x_FR_DSR)
@@ -287,17 +295,18 @@ static void pl010_set_mctrl(struct uart_port *port, unsigned int mctrl)
static void pl010_break_ctl(struct uart_port *port, int break_state)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned long flags;
unsigned int lcr_h;
- spin_lock_irqsave(&port->lock, flags);
- lcr_h = readb(port->membase + UART010_LCRH);
+ spin_lock_irqsave(&uap->port.lock, flags);
+ lcr_h = readb(uap->port.membase + UART010_LCRH);
if (break_state == -1)
lcr_h |= UART01x_LCRH_BRK;
else
lcr_h &= ~UART01x_LCRH_BRK;
- writel(lcr_h, port->membase + UART010_LCRH);
- spin_unlock_irqrestore(&port->lock, flags);
+ writel(lcr_h, uap->port.membase + UART010_LCRH);
+ spin_unlock_irqrestore(&uap->port.lock, flags);
}
static int pl010_startup(struct uart_port *port)
@@ -306,48 +315,70 @@ static int pl010_startup(struct uart_port *port)
int retval;
/*
+ * Try to enable the clock producer.
+ */
+ retval = clk_enable(uap->clk);
+ if (retval)
+ goto out;
+
+ uap->port.uartclk = clk_get_rate(uap->clk);
+
+ /*
* Allocate the IRQ
*/
- retval = request_irq(port->irq, pl010_int, 0, "uart-pl010", port);
+ retval = request_irq(uap->port.irq, pl010_int, 0, "uart-pl010", uap);
if (retval)
- return retval;
+ goto clk_dis;
/*
* initialise the old status of the modem signals
*/
- uap->old_status = readb(port->membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
+ uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY;
/*
* Finally, enable interrupts
*/
writel(UART01x_CR_UARTEN | UART010_CR_RIE | UART010_CR_RTIE,
- port->membase + UART010_CR);
+ uap->port.membase + UART010_CR);
return 0;
+
+ clk_dis:
+ clk_disable(uap->clk);
+ out:
+ return retval;
}
static void pl010_shutdown(struct uart_port *port)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
+
/*
* Free the interrupt
*/
- free_irq(port->irq, port);
+ free_irq(uap->port.irq, uap);
/*
* disable all interrupts, disable the port
*/
- writel(0, port->membase + UART010_CR);
+ writel(0, uap->port.membase + UART010_CR);
/* disable break condition and fifos */
- writel(readb(port->membase + UART010_LCRH) &
+ writel(readb(uap->port.membase + UART010_LCRH) &
~(UART01x_LCRH_BRK | UART01x_LCRH_FEN),
- port->membase + UART010_LCRH);
+ uap->port.membase + UART010_LCRH);
+
+ /*
+ * Shut down the clock producer
+ */
+ clk_disable(uap->clk);
}
static void
pl010_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int lcr_h, old_cr;
unsigned long flags;
unsigned int baud, quot;
@@ -355,7 +386,7 @@ pl010_set_termios(struct uart_port *port, struct ktermios *termios,
/*
* Ask the core to calculate the divisor for us.
*/
- baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16);
quot = uart_get_divisor(port, baud);
switch (termios->c_cflag & CSIZE) {
@@ -379,66 +410,66 @@ pl010_set_termios(struct uart_port *port, struct ktermios *termios,
if (!(termios->c_cflag & PARODD))
lcr_h |= UART01x_LCRH_EPS;
}
- if (port->fifosize > 1)
+ if (uap->port.fifosize > 1)
lcr_h |= UART01x_LCRH_FEN;
- spin_lock_irqsave(&port->lock, flags);
+ spin_lock_irqsave(&uap->port.lock, flags);
/*
* Update the per-port timeout.
*/
uart_update_timeout(port, termios->c_cflag, baud);
- port->read_status_mask = UART01x_RSR_OE;
+ uap->port.read_status_mask = UART01x_RSR_OE;
if (termios->c_iflag & INPCK)
- port->read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
+ uap->port.read_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
- port->read_status_mask |= UART01x_RSR_BE;
+ uap->port.read_status_mask |= UART01x_RSR_BE;
/*
* Characters to ignore
*/
- port->ignore_status_mask = 0;
+ uap->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
- port->ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
+ uap->port.ignore_status_mask |= UART01x_RSR_FE | UART01x_RSR_PE;
if (termios->c_iflag & IGNBRK) {
- port->ignore_status_mask |= UART01x_RSR_BE;
+ uap->port.ignore_status_mask |= UART01x_RSR_BE;
/*
* If we're ignoring parity and break indicators,
* ignore overruns too (for real raw support).
*/
if (termios->c_iflag & IGNPAR)
- port->ignore_status_mask |= UART01x_RSR_OE;
+ uap->port.ignore_status_mask |= UART01x_RSR_OE;
}
/*
* Ignore all characters if CREAD is not set.
*/
if ((termios->c_cflag & CREAD) == 0)
- port->ignore_status_mask |= UART_DUMMY_RSR_RX;
+ uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX;
/* first, disable everything */
- old_cr = readb(port->membase + UART010_CR) & ~UART010_CR_MSIE;
+ old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE;
if (UART_ENABLE_MS(port, termios->c_cflag))
old_cr |= UART010_CR_MSIE;
- writel(0, port->membase + UART010_CR);
+ writel(0, uap->port.membase + UART010_CR);
/* Set baud rate */
quot -= 1;
- writel((quot & 0xf00) >> 8, port->membase + UART010_LCRM);
- writel(quot & 0xff, port->membase + UART010_LCRL);
+ writel((quot & 0xf00) >> 8, uap->port.membase + UART010_LCRM);
+ writel(quot & 0xff, uap->port.membase + UART010_LCRL);
/*
* ----------v----------v----------v----------v-----
* NOTE: MUST BE WRITTEN AFTER UARTLCR_M & UARTLCR_L
* ----------^----------^----------^----------^-----
*/
- writel(lcr_h, port->membase + UART010_LCRH);
- writel(old_cr, port->membase + UART010_CR);
+ writel(lcr_h, uap->port.membase + UART010_LCRH);
+ writel(old_cr, uap->port.membase + UART010_CR);
- spin_unlock_irqrestore(&port->lock, flags);
+ spin_unlock_irqrestore(&uap->port.lock, flags);
}
static const char *pl010_type(struct uart_port *port)
@@ -514,47 +545,52 @@ static struct uart_amba_port *amba_ports[UART_NR];
static void pl010_console_putchar(struct uart_port *port, int ch)
{
+ struct uart_amba_port *uap = (struct uart_amba_port *)port;
unsigned int status;
do {
- status = readb(port->membase + UART01x_FR);
+ status = readb(uap->port.membase + UART01x_FR);
barrier();
} while (!UART_TX_READY(status));
- writel(ch, port->membase + UART01x_DR);
+ writel(ch, uap->port.membase + UART01x_DR);
}
static void
pl010_console_write(struct console *co, const char *s, unsigned int count)
{
- struct uart_port *port = &amba_ports[co->index]->port;
+ struct uart_amba_port *uap = amba_ports[co->index];
unsigned int status, old_cr;
+ clk_enable(uap->clk);
+
/*
* First save the CR then disable the interrupts
*/
- old_cr = readb(port->membase + UART010_CR);
- writel(UART01x_CR_UARTEN, port->membase + UART010_CR);
+ old_cr = readb(uap->port.membase + UART010_CR);
+ writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR);
- uart_console_write(port, s, count, pl010_console_putchar);
+ uart_console_write(&uap->port, s, count, pl010_console_putchar);
/*
* Finally, wait for transmitter to become empty
* and restore the TCR
*/
do {
- status = readb(port->membase + UART01x_FR);
+ status = readb(uap->port.membase + UART01x_FR);
barrier();
} while (status & UART01x_FR_BUSY);
- writel(old_cr, port->membase + UART010_CR);
+ writel(old_cr, uap->port.membase + UART010_CR);
+
+ clk_disable(uap->clk);
}
static void __init
-pl010_console_get_options(struct uart_port *port, int *baud,
+pl010_console_get_options(struct uart_amba_port *uap, int *baud,
int *parity, int *bits)
{
- if (readb(port->membase + UART010_CR) & UART01x_CR_UARTEN) {
+ if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) {
unsigned int lcr_h, quot;
- lcr_h = readb(port->membase + UART010_LCRH);
+ lcr_h = readb(uap->port.membase + UART010_LCRH);
*parity = 'n';
if (lcr_h & UART01x_LCRH_PEN) {
@@ -569,14 +605,15 @@ pl010_console_get_options(struct uart_port *port, int *baud,
else
*bits = 8;
- quot = readb(port->membase + UART010_LCRL) | readb(port->membase + UART010_LCRM) << 8;
- *baud = port->uartclk / (16 * (quot + 1));
+ quot = readb(uap->port.membase + UART010_LCRL) |
+ readb(uap->port.membase + UART010_LCRM) << 8;
+ *baud = uap->port.uartclk / (16 * (quot + 1));
}
}
static int __init pl010_console_setup(struct console *co, char *options)
{
- struct uart_port *port;
+ struct uart_amba_port *uap;
int baud = 38400;
int bits = 8;
int parity = 'n';
@@ -589,16 +626,18 @@ static int __init pl010_console_setup(struct console *co, char *options)
*/
if (co->index >= UART_NR)
co->index = 0;
- if (!amba_ports[co->index])
+ uap = amba_ports[co->index];
+ if (!uap)
return -ENODEV;
- port = &amba_ports[co->index]->port;
+
+ uap->port.uartclk = clk_get_rate(uap->clk);
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
- pl010_console_get_options(port, &baud, &parity, &bits);
+ pl010_console_get_options(uap, &baud, &parity, &bits);
- return uart_set_options(port, co, baud, parity, bits, flow);
+ return uart_set_options(&uap->port, co, baud, parity, bits, flow);
}
static struct uart_driver amba_reg;
@@ -629,7 +668,7 @@ static struct uart_driver amba_reg = {
static int pl010_probe(struct amba_device *dev, void *id)
{
- struct uart_amba_port *port;
+ struct uart_amba_port *uap;
void __iomem *base;
int i, ret;
@@ -642,8 +681,8 @@ static int pl010_probe(struct amba_device *dev, void *id)
goto out;
}
- port = kzalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
- if (!port) {
+ uap = kzalloc(sizeof(struct uart_amba_port), GFP_KERNEL);
+ if (!uap) {
ret = -ENOMEM;
goto out;
}
@@ -654,51 +693,57 @@ static int pl010_probe(struct amba_device *dev, void *id)
goto free;
}
- port->port.dev = &dev->dev;
- port->port.mapbase = dev->res.start;
- port->port.membase = base;
- port->port.iotype = UPIO_MEM;
- port->port.irq = dev->irq[0];
- port->port.uartclk = 14745600;
- port->port.fifosize = 16;
- port->port.ops = &amba_pl010_pops;
- port->port.flags = UPF_BOOT_AUTOCONF;
- port->port.line = i;
- port->dev = dev;
- port->data = dev->dev.platform_data;
-
- amba_ports[i] = port;
-
- amba_set_drvdata(dev, port);
- ret = uart_add_one_port(&amba_reg, &port->port);
+ uap->clk = clk_get(&dev->dev, "UARTCLK");
+ if (IS_ERR(uap->clk)) {
+ ret = PTR_ERR(uap->clk);
+ goto unmap;
+ }
+
+ uap->port.dev = &dev->dev;
+ uap->port.mapbase = dev->res.start;
+ uap->port.membase = base;
+ uap->port.iotype = UPIO_MEM;
+ uap->port.irq = dev->irq[0];
+ uap->port.fifosize = 16;
+ uap->port.ops = &amba_pl010_pops;
+ uap->port.flags = UPF_BOOT_AUTOCONF;
+ uap->port.line = i;
+ uap->dev = dev;
+ uap->data = dev->dev.platform_data;
+
+ amba_ports[i] = uap;
+
+ amba_set_drvdata(dev, uap);
+ ret = uart_add_one_port(&amba_reg, &uap->port);
if (ret) {
amba_set_drvdata(dev, NULL);
amba_ports[i] = NULL;
+ clk_put(uap->clk);
+ unmap:
iounmap(base);
free:
- kfree(port);
+ kfree(uap);
}
-
out:
return ret;
}
static int pl010_remove(struct amba_device *dev)
{
- struct uart_amba_port *port = amba_get_drvdata(dev);
+ struct uart_amba_port *uap = amba_get_drvdata(dev);
int i;
amba_set_drvdata(dev, NULL);
- uart_remove_one_port(&amba_reg, &port->port);
+ uart_remove_one_port(&amba_reg, &uap->port);
for (i = 0; i < ARRAY_SIZE(amba_ports); i++)
- if (amba_ports[i] == port)
+ if (amba_ports[i] == uap)
amba_ports[i] = NULL;
- iounmap(port->port.membase);
- kfree(port);
-
+ iounmap(uap->port.membase);
+ clk_put(uap->clk);
+ kfree(uap);
return 0;
}
diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c
index 935f48fa501..3320bcd92c0 100644
--- a/drivers/serial/atmel_serial.c
+++ b/drivers/serial/atmel_serial.c
@@ -484,11 +484,16 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios * termios,
unsigned long flags;
unsigned int mode, imr, quot, baud;
+ /* Get current mode register */
+ mode = UART_GET_MR(port) & ~(ATMEL_US_USCLKS | ATMEL_US_CHRL | ATMEL_US_NBSTOP | ATMEL_US_PAR);
+
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
quot = uart_get_divisor(port, baud);
- /* Get current mode register */
- mode = UART_GET_MR(port) & ~(ATMEL_US_CHRL | ATMEL_US_NBSTOP | ATMEL_US_PAR);
+ if (quot > 65535) { /* BRGR is 16-bit, so switch to slower clock */
+ quot /= 8;
+ mode |= ATMEL_US_USCLKS_MCK_DIV8;
+ }
/* byte size */
switch (termios->c_cflag & CSIZE) {
diff --git a/drivers/serial/atmel_serial.h b/drivers/serial/atmel_serial.h
index 11b44360e10..e0141776517 100644
--- a/drivers/serial/atmel_serial.h
+++ b/drivers/serial/atmel_serial.h
@@ -46,6 +46,9 @@
#define ATMEL_US_USMODE_ISO7816_T1 6
#define ATMEL_US_USMODE_IRDA 8
#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */
+#define ATMEL_US_USCLKS_MCK (0 << 4)
+#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
+#define ATMEL_US_USCLKS_SCK (3 << 4)
#define ATMEL_US_CHRL (3 << 6) /* Character Length */
#define ATMEL_US_CHRL_5 (0 << 6)
#define ATMEL_US_CHRL_6 (1 << 6)
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c
new file mode 100644
index 00000000000..408390f93db
--- /dev/null
+++ b/drivers/serial/bfin_5xx.c
@@ -0,0 +1,1012 @@
+/*
+ * File: drivers/serial/bfin_5xx.c
+ * Based on: Based on drivers/serial/sa1100.c
+ * Author: Aubrey Li <aubrey.li@analog.com>
+ *
+ * Created:
+ * Description: Driver for blackfin 5xx serial ports
+ *
+ * Rev: $Id: bfin_5xx.c,v 1.19 2006/09/24 02:33:53 aubrey Exp $
+ *
+ * Modified:
+ * Copyright 2006 Analog Devices Inc.
+ *
+ * Bugs: Enter bugs at http://blackfin.uclinux.org/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, see the file COPYING, or write
+ * to the Free Software Foundation, Inc.,
+ * 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+ */
+
+#if defined(CONFIG_SERIAL_BFIN_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
+#define SUPPORT_SYSRQ
+#endif
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+
+#include <asm/gpio.h>
+#include <asm/mach/bfin_serial_5xx.h>
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+#include <linux/dma-mapping.h>
+#include <asm/io.h>
+#include <asm/irq.h>
+#include <asm/cacheflush.h>
+#endif
+
+/* UART name and device definitions */
+#define BFIN_SERIAL_NAME "ttyBF"
+#define BFIN_SERIAL_MAJOR 204
+#define BFIN_SERIAL_MINOR 64
+
+/*
+ * Setup for console. Argument comes from the menuconfig
+ */
+#define DMA_RX_XCOUNT 512
+#define DMA_RX_YCOUNT (PAGE_SIZE / DMA_RX_XCOUNT)
+
+#define DMA_RX_FLUSH_JIFFIES 5
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart);
+#else
+static void bfin_serial_do_work(struct work_struct *work);
+static void bfin_serial_tx_chars(struct bfin_serial_port *uart);
+static void local_put_char(struct bfin_serial_port *uart, char ch);
+#endif
+
+static void bfin_serial_mctrl_check(struct bfin_serial_port *uart);
+
+/*
+ * interrupts are disabled on entry
+ */
+static void bfin_serial_stop_tx(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ disable_dma(uart->tx_dma_channel);
+#else
+ unsigned short ier;
+
+ ier = UART_GET_IER(uart);
+ ier &= ~ETBEI;
+ UART_PUT_IER(uart, ier);
+#endif
+}
+
+/*
+ * port is locked and interrupts are disabled
+ */
+static void bfin_serial_start_tx(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ bfin_serial_dma_tx_chars(uart);
+#else
+ unsigned short ier;
+ ier = UART_GET_IER(uart);
+ ier |= ETBEI;
+ UART_PUT_IER(uart, ier);
+ bfin_serial_tx_chars(uart);
+#endif
+}
+
+/*
+ * Interrupts are enabled
+ */
+static void bfin_serial_stop_rx(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ unsigned short ier;
+
+ ier = UART_GET_IER(uart);
+ ier &= ~ERBFI;
+ UART_PUT_IER(uart, ier);
+}
+
+/*
+ * Set the modem control timer to fire immediately.
+ */
+static void bfin_serial_enable_ms(struct uart_port *port)
+{
+}
+
+#ifdef CONFIG_SERIAL_BFIN_PIO
+static void local_put_char(struct bfin_serial_port *uart, char ch)
+{
+ unsigned short status;
+ int flags = 0;
+
+ spin_lock_irqsave(&uart->port.lock, flags);
+
+ do {
+ status = UART_GET_LSR(uart);
+ } while (!(status & THRE));
+
+ UART_PUT_CHAR(uart, ch);
+ SSYNC();
+
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+}
+
+static void bfin_serial_rx_chars(struct bfin_serial_port *uart)
+{
+ struct tty_struct *tty = uart->port.info?uart->port.info->tty:0;
+ unsigned int status, ch, flg;
+#ifdef BF533_FAMILY
+ static int in_break = 0;
+#endif
+
+ status = UART_GET_LSR(uart);
+ ch = UART_GET_CHAR(uart);
+ uart->port.icount.rx++;
+
+#ifdef BF533_FAMILY
+ /* The BF533 family of processors have a nice misbehavior where
+ * they continuously generate characters for a "single" break.
+ * We have to basically ignore this flood until the "next" valid
+ * character comes across. All other Blackfin families operate
+ * properly though.
+ */
+ if (in_break) {
+ if (ch != 0) {
+ in_break = 0;
+ ch = UART_GET_CHAR(uart);
+ }
+ return;
+ }
+#endif
+
+ if (status & BI) {
+#ifdef BF533_FAMILY
+ in_break = 1;
+#endif
+ uart->port.icount.brk++;
+ if (uart_handle_break(&uart->port))
+ goto ignore_char;
+ flg = TTY_BREAK;
+ } else if (status & PE) {
+ flg = TTY_PARITY;
+ uart->port.icount.parity++;
+ } else if (status & OE) {
+ flg = TTY_OVERRUN;
+ uart->port.icount.overrun++;
+ } else if (status & FE) {
+ flg = TTY_FRAME;
+ uart->port.icount.frame++;
+ } else
+ flg = TTY_NORMAL;
+
+ if (uart_handle_sysrq_char(&uart->port, ch))
+ goto ignore_char;
+ if (tty)
+ uart_insert_char(&uart->port, status, 2, ch, flg);
+
+ignore_char:
+ if (tty)
+ tty_flip_buffer_push(tty);
+}
+
+static void bfin_serial_tx_chars(struct bfin_serial_port *uart)
+{
+ struct circ_buf *xmit = &uart->port.info->xmit;
+
+ if (uart->port.x_char) {
+ UART_PUT_CHAR(uart, uart->port.x_char);
+ uart->port.icount.tx++;
+ uart->port.x_char = 0;
+ return;
+ }
+ /*
+ * Check the modem control lines before
+ * transmitting anything.
+ */
+ bfin_serial_mctrl_check(uart);
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+ bfin_serial_stop_tx(&uart->port);
+ return;
+ }
+
+ local_put_char(uart, xmit->buf[xmit->tail]);
+ xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+ uart->port.icount.tx++;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&uart->port);
+
+ if (uart_circ_empty(xmit))
+ bfin_serial_stop_tx(&uart->port);
+}
+
+static irqreturn_t bfin_serial_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ unsigned short status;
+
+ spin_lock(&uart->port.lock);
+ status = UART_GET_IIR(uart);
+ do {
+ if ((status & IIR_STATUS) == IIR_TX_READY)
+ bfin_serial_tx_chars(uart);
+ if ((status & IIR_STATUS) == IIR_RX_READY)
+ bfin_serial_rx_chars(uart);
+ status = UART_GET_IIR(uart);
+ } while (status & (IIR_TX_READY | IIR_RX_READY));
+ spin_unlock(&uart->port.lock);
+ return IRQ_HANDLED;
+}
+
+static void bfin_serial_do_work(struct work_struct *work)
+{
+ struct bfin_serial_port *uart = container_of(work, struct bfin_serial_port, cts_workqueue);
+
+ bfin_serial_mctrl_check(uart);
+}
+
+#endif
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+static void bfin_serial_dma_tx_chars(struct bfin_serial_port *uart)
+{
+ struct circ_buf *xmit = &uart->port.info->xmit;
+ unsigned short ier;
+ int flags = 0;
+
+ if (!uart->tx_done)
+ return;
+
+ uart->tx_done = 0;
+
+ if (uart->port.x_char) {
+ UART_PUT_CHAR(uart, uart->port.x_char);
+ uart->port.icount.tx++;
+ uart->port.x_char = 0;
+ uart->tx_done = 1;
+ return;
+ }
+ /*
+ * Check the modem control lines before
+ * transmitting anything.
+ */
+ bfin_serial_mctrl_check(uart);
+
+ if (uart_circ_empty(xmit) || uart_tx_stopped(&uart->port)) {
+ bfin_serial_stop_tx(&uart->port);
+ uart->tx_done = 1;
+ return;
+ }
+
+ spin_lock_irqsave(&uart->port.lock, flags);
+ uart->tx_count = CIRC_CNT(xmit->head, xmit->tail, UART_XMIT_SIZE);
+ if (uart->tx_count > (UART_XMIT_SIZE - xmit->tail))
+ uart->tx_count = UART_XMIT_SIZE - xmit->tail;
+ blackfin_dcache_flush_range((unsigned long)(xmit->buf+xmit->tail),
+ (unsigned long)(xmit->buf+xmit->tail+uart->tx_count));
+ set_dma_config(uart->tx_dma_channel,
+ set_bfin_dma_config(DIR_READ, DMA_FLOW_STOP,
+ INTR_ON_BUF,
+ DIMENSION_LINEAR,
+ DATA_SIZE_8));
+ set_dma_start_addr(uart->tx_dma_channel, (unsigned long)(xmit->buf+xmit->tail));
+ set_dma_x_count(uart->tx_dma_channel, uart->tx_count);
+ set_dma_x_modify(uart->tx_dma_channel, 1);
+ enable_dma(uart->tx_dma_channel);
+ ier = UART_GET_IER(uart);
+ ier |= ETBEI;
+ UART_PUT_IER(uart, ier);
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+}
+
+static void bfin_serial_dma_rx_chars(struct bfin_serial_port * uart)
+{
+ struct tty_struct *tty = uart->port.info->tty;
+ int i, flg, status;
+
+ status = UART_GET_LSR(uart);
+ uart->port.icount.rx += CIRC_CNT(uart->rx_dma_buf.head, uart->rx_dma_buf.tail, UART_XMIT_SIZE);;
+
+ if (status & BI) {
+ uart->port.icount.brk++;
+ if (uart_handle_break(&uart->port))
+ goto dma_ignore_char;
+ flg = TTY_BREAK;
+ } else if (status & PE) {
+ flg = TTY_PARITY;
+ uart->port.icount.parity++;
+ } else if (status & OE) {
+ flg = TTY_OVERRUN;
+ uart->port.icount.overrun++;
+ } else if (status & FE) {
+ flg = TTY_FRAME;
+ uart->port.icount.frame++;
+ } else
+ flg = TTY_NORMAL;
+
+ for (i = uart->rx_dma_buf.head; i < uart->rx_dma_buf.tail; i++) {
+ if (uart_handle_sysrq_char(&uart->port, uart->rx_dma_buf.buf[i]))
+ goto dma_ignore_char;
+ uart_insert_char(&uart->port, status, 2, uart->rx_dma_buf.buf[i], flg);
+ }
+dma_ignore_char:
+ tty_flip_buffer_push(tty);
+}
+
+void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart)
+{
+ int x_pos, pos;
+ int flags = 0;
+
+ bfin_serial_dma_tx_chars(uart);
+
+ spin_lock_irqsave(&uart->port.lock, flags);
+ x_pos = DMA_RX_XCOUNT - get_dma_curr_xcount(uart->rx_dma_channel);
+ if (x_pos == DMA_RX_XCOUNT)
+ x_pos = 0;
+
+ pos = uart->rx_dma_nrows * DMA_RX_XCOUNT + x_pos;
+
+ if (pos>uart->rx_dma_buf.tail) {
+ uart->rx_dma_buf.tail = pos;
+ bfin_serial_dma_rx_chars(uart);
+ uart->rx_dma_buf.head = uart->rx_dma_buf.tail;
+ }
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+ uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
+ add_timer(&(uart->rx_dma_timer));
+}
+
+static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ struct circ_buf *xmit = &uart->port.info->xmit;
+ unsigned short ier;
+
+ spin_lock(&uart->port.lock);
+ if (!(get_dma_curr_irqstat(uart->tx_dma_channel)&DMA_RUN)) {
+ clear_dma_irqstat(uart->tx_dma_channel);
+ disable_dma(uart->tx_dma_channel);
+ ier = UART_GET_IER(uart);
+ ier &= ~ETBEI;
+ UART_PUT_IER(uart, ier);
+ xmit->tail = (xmit->tail+uart->tx_count) &(UART_XMIT_SIZE -1);
+ uart->port.icount.tx+=uart->tx_count;
+
+ if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+ uart_write_wakeup(&uart->port);
+
+ if (uart_circ_empty(xmit))
+ bfin_serial_stop_tx(&uart->port);
+ uart->tx_done = 1;
+ }
+
+ spin_unlock(&uart->port.lock);
+ return IRQ_HANDLED;
+}
+
+static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id)
+{
+ struct bfin_serial_port *uart = dev_id;
+ unsigned short irqstat;
+
+ uart->rx_dma_nrows++;
+ if (uart->rx_dma_nrows == DMA_RX_YCOUNT) {
+ uart->rx_dma_nrows = 0;
+ uart->rx_dma_buf.tail = DMA_RX_XCOUNT*DMA_RX_YCOUNT;
+ bfin_serial_dma_rx_chars(uart);
+ uart->rx_dma_buf.head = uart->rx_dma_buf.tail = 0;
+ }
+ spin_lock(&uart->port.lock);
+ irqstat = get_dma_curr_irqstat(uart->rx_dma_channel);
+ clear_dma_irqstat(uart->rx_dma_channel);
+
+ spin_unlock(&uart->port.lock);
+ return IRQ_HANDLED;
+}
+#endif
+
+/*
+ * Return TIOCSER_TEMT when transmitter is not busy.
+ */
+static unsigned int bfin_serial_tx_empty(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ unsigned short lsr;
+
+ lsr = UART_GET_LSR(uart);
+ if (lsr & TEMT)
+ return TIOCSER_TEMT;
+ else
+ return 0;
+}
+
+static unsigned int bfin_serial_get_mctrl(struct uart_port *port)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->cts_pin < 0)
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+ if (gpio_get_value(uart->cts_pin))
+ return TIOCM_DSR | TIOCM_CAR;
+ else
+#endif
+ return TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+}
+
+static void bfin_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ if (uart->rts_pin < 0)
+ return;
+
+ if (mctrl & TIOCM_RTS)
+ gpio_set_value(uart->rts_pin, 0);
+ else
+ gpio_set_value(uart->rts_pin, 1);
+#endif
+}
+
+/*
+ * Handle any change of modem status signal since we were last called.
+ */
+static void bfin_serial_mctrl_check(struct bfin_serial_port *uart)
+{
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ unsigned int status;
+# ifdef CONFIG_SERIAL_BFIN_DMA
+ struct uart_info *info = uart->port.info;
+ struct tty_struct *tty = info->tty;
+
+ status = bfin_serial_get_mctrl(&uart->port);
+ if (!(status & TIOCM_CTS)) {
+ tty->hw_stopped = 1;
+ } else {
+ tty->hw_stopped = 0;
+ }
+# else
+ status = bfin_serial_get_mctrl(&uart->port);
+ uart_handle_cts_change(&uart->port, status & TIOCM_CTS);
+ if (!(status & TIOCM_CTS))
+ schedule_work(&uart->cts_workqueue);
+# endif
+#endif
+}
+
+/*
+ * Interrupts are always disabled.
+ */
+static void bfin_serial_break_ctl(struct uart_port *port, int break_state)
+{
+}
+
+static int bfin_serial_startup(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ dma_addr_t dma_handle;
+
+ if (request_dma(uart->rx_dma_channel, "BFIN_UART_RX") < 0) {
+ printk(KERN_NOTICE "Unable to attach Blackfin UART RX DMA channel\n");
+ return -EBUSY;
+ }
+
+ if (request_dma(uart->tx_dma_channel, "BFIN_UART_TX") < 0) {
+ printk(KERN_NOTICE "Unable to attach Blackfin UART TX DMA channel\n");
+ free_dma(uart->rx_dma_channel);
+ return -EBUSY;
+ }
+
+ set_dma_callback(uart->rx_dma_channel, bfin_serial_dma_rx_int, uart);
+ set_dma_callback(uart->tx_dma_channel, bfin_serial_dma_tx_int, uart);
+
+ uart->rx_dma_buf.buf = (unsigned char *)dma_alloc_coherent(NULL, PAGE_SIZE, &dma_handle, GFP_DMA);
+ uart->rx_dma_buf.head = 0;
+ uart->rx_dma_buf.tail = 0;
+ uart->rx_dma_nrows = 0;
+
+ set_dma_config(uart->rx_dma_channel,
+ set_bfin_dma_config(DIR_WRITE, DMA_FLOW_AUTO,
+ INTR_ON_ROW, DIMENSION_2D,
+ DATA_SIZE_8));
+ set_dma_x_count(uart->rx_dma_channel, DMA_RX_XCOUNT);
+ set_dma_x_modify(uart->rx_dma_channel, 1);
+ set_dma_y_count(uart->rx_dma_channel, DMA_RX_YCOUNT);
+ set_dma_y_modify(uart->rx_dma_channel, 1);
+ set_dma_start_addr(uart->rx_dma_channel, (unsigned long)uart->rx_dma_buf.buf);
+ enable_dma(uart->rx_dma_channel);
+
+ uart->rx_dma_timer.data = (unsigned long)(uart);
+ uart->rx_dma_timer.function = (void *)bfin_serial_rx_dma_timeout;
+ uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES;
+ add_timer(&(uart->rx_dma_timer));
+#else
+ if (request_irq
+ (uart->port.irq, bfin_serial_int, IRQF_DISABLED,
+ "BFIN_UART_RX", uart)) {
+ printk(KERN_NOTICE "Unable to attach BlackFin UART RX interrupt\n");
+ return -EBUSY;
+ }
+
+ if (request_irq
+ (uart->port.irq+1, bfin_serial_int, IRQF_DISABLED,
+ "BFIN_UART_TX", uart)) {
+ printk(KERN_NOTICE "Unable to attach BlackFin UART TX interrupt\n");
+ free_irq(uart->port.irq, uart);
+ return -EBUSY;
+ }
+#endif
+ UART_PUT_IER(uart, UART_GET_IER(uart) | ERBFI);
+ return 0;
+}
+
+static void bfin_serial_shutdown(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ disable_dma(uart->tx_dma_channel);
+ free_dma(uart->tx_dma_channel);
+ disable_dma(uart->rx_dma_channel);
+ free_dma(uart->rx_dma_channel);
+ del_timer(&(uart->rx_dma_timer));
+#else
+ free_irq(uart->port.irq, uart);
+ free_irq(uart->port.irq+1, uart);
+#endif
+}
+
+static void
+bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios,
+ struct ktermios *old)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ unsigned long flags;
+ unsigned int baud, quot;
+ unsigned short val, ier, lsr, lcr = 0;
+
+ switch (termios->c_cflag & CSIZE) {
+ case CS8:
+ lcr = WLS(8);
+ break;
+ case CS7:
+ lcr = WLS(7);
+ break;
+ case CS6:
+ lcr = WLS(6);
+ break;
+ case CS5:
+ lcr = WLS(5);
+ break;
+ default:
+ printk(KERN_ERR "%s: word lengh not supported\n",
+ __FUNCTION__);
+ }
+
+ if (termios->c_cflag & CSTOPB)
+ lcr |= STB;
+ if (termios->c_cflag & PARENB) {
+ lcr |= PEN;
+ if (!(termios->c_cflag & PARODD))
+ lcr |= EPS;
+ }
+
+ /* These controls are not implemented for this port */
+ termios->c_iflag |= INPCK | BRKINT | PARMRK;
+ termios->c_iflag &= ~(IGNPAR | IGNBRK);
+
+ /* These controls are not implemented for this port */
+ termios->c_iflag |= INPCK | BRKINT | PARMRK;
+ termios->c_iflag &= ~(IGNPAR | IGNBRK);
+
+ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
+ quot = uart_get_divisor(port, baud);
+ spin_lock_irqsave(&uart->port.lock, flags);
+
+ do {
+ lsr = UART_GET_LSR(uart);
+ } while (!(lsr & TEMT));
+
+ /* Disable UART */
+ ier = UART_GET_IER(uart);
+ UART_PUT_IER(uart, 0);
+
+ /* Set DLAB in LCR to Access DLL and DLH */
+ val = UART_GET_LCR(uart);
+ val |= DLAB;
+ UART_PUT_LCR(uart, val);
+ SSYNC();
+
+ UART_PUT_DLL(uart, quot & 0xFF);
+ SSYNC();
+ UART_PUT_DLH(uart, (quot >> 8) & 0xFF);
+ SSYNC();
+
+ /* Clear DLAB in LCR to Access THR RBR IER */
+ val = UART_GET_LCR(uart);
+ val &= ~DLAB;
+ UART_PUT_LCR(uart, val);
+ SSYNC();
+
+ UART_PUT_LCR(uart, lcr);
+
+ /* Enable UART */
+ UART_PUT_IER(uart, ier);
+
+ val = UART_GET_GCTL(uart);
+ val |= UCEN;
+ UART_PUT_GCTL(uart, val);
+
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+}
+
+static const char *bfin_serial_type(struct uart_port *port)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+ return uart->port.type == PORT_BFIN ? "BFIN-UART" : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'.
+ */
+static void bfin_serial_release_port(struct uart_port *port)
+{
+}
+
+/*
+ * Request the memory region(s) being used by 'port'.
+ */
+static int bfin_serial_request_port(struct uart_port *port)
+{
+ return 0;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void bfin_serial_config_port(struct uart_port *port, int flags)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+
+ if (flags & UART_CONFIG_TYPE &&
+ bfin_serial_request_port(&uart->port) == 0)
+ uart->port.type = PORT_BFIN;
+}
+
+/*
+ * Verify the new serial_struct (for TIOCSSERIAL).
+ * The only change we allow are to the flags and type, and
+ * even then only between PORT_BFIN and PORT_UNKNOWN
+ */
+static int
+bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+ return 0;
+}
+
+static struct uart_ops bfin_serial_pops = {
+ .tx_empty = bfin_serial_tx_empty,
+ .set_mctrl = bfin_serial_set_mctrl,
+ .get_mctrl = bfin_serial_get_mctrl,
+ .stop_tx = bfin_serial_stop_tx,
+ .start_tx = bfin_serial_start_tx,
+ .stop_rx = bfin_serial_stop_rx,
+ .enable_ms = bfin_serial_enable_ms,
+ .break_ctl = bfin_serial_break_ctl,
+ .startup = bfin_serial_startup,
+ .shutdown = bfin_serial_shutdown,
+ .set_termios = bfin_serial_set_termios,
+ .type = bfin_serial_type,
+ .release_port = bfin_serial_release_port,
+ .request_port = bfin_serial_request_port,
+ .config_port = bfin_serial_config_port,
+ .verify_port = bfin_serial_verify_port,
+};
+
+static void __init bfin_serial_init_ports(void)
+{
+ static int first = 1;
+ int i;
+
+ if (!first)
+ return;
+ first = 0;
+
+ for (i = 0; i < nr_ports; i++) {
+ bfin_serial_ports[i].port.uartclk = get_sclk();
+ bfin_serial_ports[i].port.ops = &bfin_serial_pops;
+ bfin_serial_ports[i].port.line = i;
+ bfin_serial_ports[i].port.iotype = UPIO_MEM;
+ bfin_serial_ports[i].port.membase =
+ (void __iomem *)bfin_serial_resource[i].uart_base_addr;
+ bfin_serial_ports[i].port.mapbase =
+ bfin_serial_resource[i].uart_base_addr;
+ bfin_serial_ports[i].port.irq =
+ bfin_serial_resource[i].uart_irq;
+ bfin_serial_ports[i].port.flags = UPF_BOOT_AUTOCONF;
+#ifdef CONFIG_SERIAL_BFIN_DMA
+ bfin_serial_ports[i].tx_done = 1;
+ bfin_serial_ports[i].tx_count = 0;
+ bfin_serial_ports[i].tx_dma_channel =
+ bfin_serial_resource[i].uart_tx_dma_channel;
+ bfin_serial_ports[i].rx_dma_channel =
+ bfin_serial_resource[i].uart_rx_dma_channel;
+ init_timer(&(bfin_serial_ports[i].rx_dma_timer));
+#else
+ INIT_WORK(&bfin_serial_ports[i].cts_workqueue, bfin_serial_do_work);
+#endif
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ bfin_serial_ports[i].cts_pin =
+ bfin_serial_resource[i].uart_cts_pin;
+ bfin_serial_ports[i].rts_pin =
+ bfin_serial_resource[i].uart_rts_pin;
+#endif
+ bfin_serial_hw_init(&bfin_serial_ports[i]);
+
+ }
+}
+
+#ifdef CONFIG_SERIAL_BFIN_CONSOLE
+static void bfin_serial_console_putchar(struct uart_port *port, int ch)
+{
+ struct bfin_serial_port *uart = (struct bfin_serial_port *)port;
+ while (!(UART_GET_LSR(uart)))
+ barrier();
+ UART_PUT_CHAR(uart, ch);
+ SSYNC();
+}
+
+/*
+ * Interrupts are disabled on entering
+ */
+static void
+bfin_serial_console_write(struct console *co, const char *s, unsigned int count)
+{
+ struct bfin_serial_port *uart = &bfin_serial_ports[co->index];
+ int flags = 0;
+
+ spin_lock_irqsave(&uart->port.lock, flags);
+ uart_console_write(&uart->port, s, count, bfin_serial_console_putchar);
+ spin_unlock_irqrestore(&uart->port.lock, flags);
+
+}
+
+/*
+ * If the port was already initialised (eg, by a boot loader),
+ * try to determine the current setup.
+ */
+static void __init
+bfin_serial_console_get_options(struct bfin_serial_port *uart, int *baud,
+ int *parity, int *bits)
+{
+ unsigned short status;
+
+ status = UART_GET_IER(uart) & (ERBFI | ETBEI);
+ if (status == (ERBFI | ETBEI)) {
+ /* ok, the port was enabled */
+ unsigned short lcr, val;
+ unsigned short dlh, dll;
+
+ lcr = UART_GET_LCR(uart);
+
+ *parity = 'n';
+ if (lcr & PEN) {
+ if (lcr & EPS)
+ *parity = 'e';
+ else
+ *parity = 'o';
+ }
+ switch (lcr & 0x03) {
+ case 0: *bits = 5; break;
+ case 1: *bits = 6; break;
+ case 2: *bits = 7; break;
+ case 3: *bits = 8; break;
+ }
+ /* Set DLAB in LCR to Access DLL and DLH */
+ val = UART_GET_LCR(uart);
+ val |= DLAB;
+ UART_PUT_LCR(uart, val);
+
+ dll = UART_GET_DLL(uart);
+ dlh = UART_GET_DLH(uart);
+
+ /* Clear DLAB in LCR to Access THR RBR IER */
+ val = UART_GET_LCR(uart);
+ val &= ~DLAB;
+ UART_PUT_LCR(uart, val);
+
+ *baud = get_sclk() / (16*(dll | dlh << 8));
+ }
+ pr_debug("%s:baud = %d, parity = %c, bits= %d\n", __FUNCTION__, *baud, *parity, *bits);
+}
+
+static int __init
+bfin_serial_console_setup(struct console *co, char *options)
+{
+ struct bfin_serial_port *uart;
+ int baud = 57600;
+ int bits = 8;
+ int parity = 'n';
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ int flow = 'r';
+#else
+ int flow = 'n';
+#endif
+
+ /*
+ * Check whether an invalid uart number has been specified, and
+ * if so, search for the first available port that does have
+ * console support.
+ */
+ if (co->index == -1 || co->index >= nr_ports)
+ co->index = 0;
+ uart = &bfin_serial_ports[co->index];
+
+ if (options)
+ uart_parse_options(options, &baud, &parity, &bits, &flow);
+ else
+ bfin_serial_console_get_options(uart, &baud, &parity, &bits);
+
+ return uart_set_options(&uart->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver bfin_serial_reg;
+static struct console bfin_serial_console = {
+ .name = BFIN_SERIAL_NAME,
+ .write = bfin_serial_console_write,
+ .device = uart_console_device,
+ .setup = bfin_serial_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
+ .data = &bfin_serial_reg,
+};
+
+static int __init bfin_serial_rs_console_init(void)
+{
+ bfin_serial_init_ports();
+ register_console(&bfin_serial_console);
+ return 0;
+}
+console_initcall(bfin_serial_rs_console_init);
+
+#define BFIN_SERIAL_CONSOLE &bfin_serial_console
+#else
+#define BFIN_SERIAL_CONSOLE NULL
+#endif
+
+static struct uart_driver bfin_serial_reg = {
+ .owner = THIS_MODULE,
+ .driver_name = "bfin-uart",
+ .dev_name = BFIN_SERIAL_NAME,
+ .major = BFIN_SERIAL_MAJOR,
+ .minor = BFIN_SERIAL_MINOR,
+ .nr = NR_PORTS,
+ .cons = BFIN_SERIAL_CONSOLE,
+};
+
+static int bfin_serial_suspend(struct platform_device *dev, pm_message_t state)
+{
+ struct bfin_serial_port *uart = platform_get_drvdata(dev);
+
+ if (uart)
+ uart_suspend_port(&bfin_serial_reg, &uart->port);
+
+ return 0;
+}
+
+static int bfin_serial_resume(struct platform_device *dev)
+{
+ struct bfin_serial_port *uart = platform_get_drvdata(dev);
+
+ if (uart)
+ uart_resume_port(&bfin_serial_reg, &uart->port);
+
+ return 0;
+}
+
+static int bfin_serial_probe(struct platform_device *dev)
+{
+ struct resource *res = dev->resource;
+ int i;
+
+ for (i = 0; i < dev->num_resources; i++, res++)
+ if (res->flags & IORESOURCE_MEM)
+ break;
+
+ if (i < dev->num_resources) {
+ for (i = 0; i < nr_ports; i++, res++) {
+ if (bfin_serial_ports[i].port.mapbase != res->start)
+ continue;
+ bfin_serial_ports[i].port.dev = &dev->dev;
+ uart_add_one_port(&bfin_serial_reg, &bfin_serial_ports[i].port);
+ platform_set_drvdata(dev, &bfin_serial_ports[i]);
+ }
+ }
+
+ return 0;
+}
+
+static int bfin_serial_remove(struct platform_device *pdev)
+{
+ struct bfin_serial_port *uart = platform_get_drvdata(pdev);
+
+
+#ifdef CONFIG_SERIAL_BFIN_CTSRTS
+ gpio_free(uart->cts_pin);
+ gpio_free(uart->rts_pin);
+#endif
+
+ platform_set_drvdata(pdev, NULL);
+
+ if (uart)
+ uart_remove_one_port(&bfin_serial_reg, &uart->port);
+
+ return 0;
+}
+
+static struct platform_driver bfin_serial_driver = {
+ .probe = bfin_serial_probe,
+ .remove = bfin_serial_remove,
+ .suspend = bfin_serial_suspend,
+ .resume = bfin_serial_resume,
+ .driver = {
+ .name = "bfin-uart",
+ },
+};
+
+static int __init bfin_serial_init(void)
+{
+ int ret;
+
+ pr_info("Serial: Blackfin serial driver\n");
+
+ bfin_serial_init_ports();
+
+ ret = uart_register_driver(&bfin_serial_reg);
+ if (ret == 0) {
+ ret = platform_driver_register(&bfin_serial_driver);
+ if (ret) {
+ pr_debug("uart register failed\n");
+ uart_unregister_driver(&bfin_serial_reg);
+ }
+ }
+ return ret;
+}
+
+static void __exit bfin_serial_exit(void)
+{
+ platform_driver_unregister(&bfin_serial_driver);
+ uart_unregister_driver(&bfin_serial_reg);
+}
+
+module_init(bfin_serial_init);
+module_exit(bfin_serial_exit);
+
+MODULE_AUTHOR("Aubrey.Li <aubrey.li@analog.com>");
+MODULE_DESCRIPTION("Blackfin generic serial port driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_CHARDEV_MAJOR(BFIN_SERIAL_MAJOR);
diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c
index 7a3b97fdf8d..f23972bc00c 100644
--- a/drivers/serial/cpm_uart/cpm_uart_core.c
+++ b/drivers/serial/cpm_uart/cpm_uart_core.c
@@ -934,7 +934,7 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = {
.irq = SMC1_IRQ,
.ops = &cpm_uart_pops,
.iotype = UPIO_MEM,
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SMC1].port.lock),
},
.flags = FLAG_SMC,
.tx_nrfifos = TX_NUM_FIFO,
@@ -948,7 +948,7 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = {
.irq = SMC2_IRQ,
.ops = &cpm_uart_pops,
.iotype = UPIO_MEM,
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SMC2].port.lock),
},
.flags = FLAG_SMC,
.tx_nrfifos = TX_NUM_FIFO,
@@ -965,7 +965,7 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = {
.irq = SCC1_IRQ,
.ops = &cpm_uart_pops,
.iotype = UPIO_MEM,
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC1].port.lock),
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
@@ -979,7 +979,7 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = {
.irq = SCC2_IRQ,
.ops = &cpm_uart_pops,
.iotype = UPIO_MEM,
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC2].port.lock),
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
@@ -993,7 +993,7 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = {
.irq = SCC3_IRQ,
.ops = &cpm_uart_pops,
.iotype = UPIO_MEM,
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC3].port.lock),
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
@@ -1007,7 +1007,7 @@ struct uart_cpm_port cpm_uart_ports[UART_NR] = {
.irq = SCC4_IRQ,
.ops = &cpm_uart_pops,
.iotype = UPIO_MEM,
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(cpm_uart_ports[UART_SCC4].port.lock),
},
.tx_nrfifos = TX_NUM_FIFO,
.tx_fifosize = TX_BUF_SIZE,
diff --git a/drivers/serial/crisv10.h b/drivers/serial/crisv10.h
deleted file mode 100644
index 4a23340663a..00000000000
--- a/drivers/serial/crisv10.h
+++ /dev/null
@@ -1,136 +0,0 @@
-/*
- * serial.h: Arch-dep definitions for the Etrax100 serial driver.
- *
- * Copyright (C) 1998, 1999, 2000 Axis Communications AB
- */
-
-#ifndef _ETRAX_SERIAL_H
-#define _ETRAX_SERIAL_H
-
-#include <linux/circ_buf.h>
-#include <asm/termios.h>
-
-/* Software state per channel */
-
-#ifdef __KERNEL__
-/*
- * This is our internal structure for each serial port's state.
- *
- * Many fields are paralleled by the structure used by the serial_struct
- * structure.
- *
- * For definitions of the flags field, see tty.h
- */
-
-#define SERIAL_RECV_DESCRIPTORS 8
-
-struct etrax_recv_buffer {
- struct etrax_recv_buffer *next;
- unsigned short length;
- unsigned char error;
- unsigned char pad;
-
- unsigned char buffer[0];
-};
-
-struct e100_serial {
- int baud;
- volatile u8 *port; /* R_SERIALx_CTRL */
- u32 irq; /* bitnr in R_IRQ_MASK2 for dmaX_descr */
-
- /* Output registers */
- volatile u8 *oclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
- volatile u32 *ofirstadr; /* adr to R_DMA_CHx_FIRST */
- volatile u8 *ocmdadr; /* adr to R_DMA_CHx_CMD */
- const volatile u8 *ostatusadr; /* adr to R_DMA_CHx_STATUS */
-
- /* Input registers */
- volatile u8 *iclrintradr; /* adr to R_DMA_CHx_CLR_INTR */
- volatile u32 *ifirstadr; /* adr to R_DMA_CHx_FIRST */
- volatile u8 *icmdadr; /* adr to R_DMA_CHx_CMD */
- volatile u32 *idescradr; /* adr to R_DMA_CHx_DESCR */
-
- int flags; /* defined in tty.h */
-
- u8 rx_ctrl; /* shadow for R_SERIALx_REC_CTRL */
- u8 tx_ctrl; /* shadow for R_SERIALx_TR_CTRL */
- u8 iseteop; /* bit number for R_SET_EOP for the input dma */
- int enabled; /* Set to 1 if the port is enabled in HW config */
-
- u8 dma_out_enabled:1; /* Set to 1 if DMA should be used */
- u8 dma_in_enabled:1; /* Set to 1 if DMA should be used */
-
- /* end of fields defined in rs_table[] in .c-file */
- u8 uses_dma_in; /* Set to 1 if DMA is used */
- u8 uses_dma_out; /* Set to 1 if DMA is used */
- u8 forced_eop; /* a fifo eop has been forced */
- int baud_base; /* For special baudrates */
- int custom_divisor; /* For special baudrates */
- struct etrax_dma_descr tr_descr;
- struct etrax_dma_descr rec_descr[SERIAL_RECV_DESCRIPTORS];
- int cur_rec_descr;
-
- volatile int tr_running; /* 1 if output is running */
-
- struct tty_struct *tty;
- int read_status_mask;
- int ignore_status_mask;
- int x_char; /* xon/xoff character */
- int close_delay;
- unsigned short closing_wait;
- unsigned short closing_wait2;
- unsigned long event;
- unsigned long last_active;
- int line;
- int type; /* PORT_ETRAX */
- int count; /* # of fd on device */
- int blocked_open; /* # of blocked opens */
- struct circ_buf xmit;
- struct etrax_recv_buffer *first_recv_buffer;
- struct etrax_recv_buffer *last_recv_buffer;
- unsigned int recv_cnt;
- unsigned int max_recv_cnt;
-
- struct work_struct work;
- struct async_icount icount; /* error-statistics etc.*/
- struct ktermios normal_termios;
- struct ktermios callout_termios;
-#ifdef DECLARE_WAITQUEUE
- wait_queue_head_t open_wait;
- wait_queue_head_t close_wait;
-#else
- struct wait_queue *open_wait;
- struct wait_queue *close_wait;
-#endif
-
- unsigned long char_time_usec; /* The time for 1 char, in usecs */
- unsigned long flush_time_usec; /* How often we should flush */
- unsigned long last_tx_active_usec; /* Last tx usec in the jiffies */
- unsigned long last_tx_active; /* Last tx time in jiffies */
- unsigned long last_rx_active_usec; /* Last rx usec in the jiffies */
- unsigned long last_rx_active; /* Last rx time in jiffies */
-
- int break_detected_cnt;
- int errorcode;
-
-#ifdef CONFIG_ETRAX_RS485
- struct rs485_control rs485; /* RS-485 support */
-#endif
-};
-
-/* this PORT is not in the standard serial.h. it's not actually used for
- * anything since we only have one type of async serial-port anyway in this
- * system.
- */
-
-#define PORT_ETRAX 1
-
-/*
- * Events are used to schedule things to happen at timer-interrupt
- * time, instead of at rs interrupt time.
- */
-#define RS_EVENT_WRITE_WAKEUP 0
-
-#endif /* __KERNEL__ */
-
-#endif /* !_ETRAX_SERIAL_H */
diff --git a/drivers/serial/icom.c b/drivers/serial/icom.c
index 246c5572667..6202995e821 100644
--- a/drivers/serial/icom.c
+++ b/drivers/serial/icom.c
@@ -47,7 +47,6 @@
#include <linux/pci.h>
#include <linux/vmalloc.h>
#include <linux/smp.h>
-#include <linux/smp_lock.h>
#include <linux/spinlock.h>
#include <linux/kobject.h>
#include <linux/firmware.h>
diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c
index 04cc88cc528..e42faa4e428 100644
--- a/drivers/serial/imx.c
+++ b/drivers/serial/imx.c
@@ -46,6 +46,122 @@
#include <asm/hardware.h>
#include <asm/arch/imx-uart.h>
+/* Register definitions */
+#define URXD0 0x0 /* Receiver Register */
+#define URTX0 0x40 /* Transmitter Register */
+#define UCR1 0x80 /* Control Register 1 */
+#define UCR2 0x84 /* Control Register 2 */
+#define UCR3 0x88 /* Control Register 3 */
+#define UCR4 0x8c /* Control Register 4 */
+#define UFCR 0x90 /* FIFO Control Register */
+#define USR1 0x94 /* Status Register 1 */
+#define USR2 0x98 /* Status Register 2 */
+#define UESC 0x9c /* Escape Character Register */
+#define UTIM 0xa0 /* Escape Timer Register */
+#define UBIR 0xa4 /* BRM Incremental Register */
+#define UBMR 0xa8 /* BRM Modulator Register */
+#define UBRC 0xac /* Baud Rate Count Register */
+#define BIPR1 0xb0 /* Incremental Preset Register 1 */
+#define BIPR2 0xb4 /* Incremental Preset Register 2 */
+#define BIPR3 0xb8 /* Incremental Preset Register 3 */
+#define BIPR4 0xbc /* Incremental Preset Register 4 */
+#define BMPR1 0xc0 /* BRM Modulator Register 1 */
+#define BMPR2 0xc4 /* BRM Modulator Register 2 */
+#define BMPR3 0xc8 /* BRM Modulator Register 3 */
+#define BMPR4 0xcc /* BRM Modulator Register 4 */
+#define UTS 0xd0 /* UART Test Register */
+
+/* UART Control Register Bit Fields.*/
+#define URXD_CHARRDY (1<<15)
+#define URXD_ERR (1<<14)
+#define URXD_OVRRUN (1<<13)
+#define URXD_FRMERR (1<<12)
+#define URXD_BRK (1<<11)
+#define URXD_PRERR (1<<10)
+#define UCR1_ADEN (1<<15) /* Auto dectect interrupt */
+#define UCR1_ADBR (1<<14) /* Auto detect baud rate */
+#define UCR1_TRDYEN (1<<13) /* Transmitter ready interrupt enable */
+#define UCR1_IDEN (1<<12) /* Idle condition interrupt */
+#define UCR1_RRDYEN (1<<9) /* Recv ready interrupt enable */
+#define UCR1_RDMAEN (1<<8) /* Recv ready DMA enable */
+#define UCR1_IREN (1<<7) /* Infrared interface enable */
+#define UCR1_TXMPTYEN (1<<6) /* Transimitter empty interrupt enable */
+#define UCR1_RTSDEN (1<<5) /* RTS delta interrupt enable */
+#define UCR1_SNDBRK (1<<4) /* Send break */
+#define UCR1_TDMAEN (1<<3) /* Transmitter ready DMA enable */
+#define UCR1_UARTCLKEN (1<<2) /* UART clock enabled */
+#define UCR1_DOZE (1<<1) /* Doze */
+#define UCR1_UARTEN (1<<0) /* UART enabled */
+#define UCR2_ESCI (1<<15) /* Escape seq interrupt enable */
+#define UCR2_IRTS (1<<14) /* Ignore RTS pin */
+#define UCR2_CTSC (1<<13) /* CTS pin control */
+#define UCR2_CTS (1<<12) /* Clear to send */
+#define UCR2_ESCEN (1<<11) /* Escape enable */
+#define UCR2_PREN (1<<8) /* Parity enable */
+#define UCR2_PROE (1<<7) /* Parity odd/even */
+#define UCR2_STPB (1<<6) /* Stop */
+#define UCR2_WS (1<<5) /* Word size */
+#define UCR2_RTSEN (1<<4) /* Request to send interrupt enable */
+#define UCR2_TXEN (1<<2) /* Transmitter enabled */
+#define UCR2_RXEN (1<<1) /* Receiver enabled */
+#define UCR2_SRST (1<<0) /* SW reset */
+#define UCR3_DTREN (1<<13) /* DTR interrupt enable */
+#define UCR3_PARERREN (1<<12) /* Parity enable */
+#define UCR3_FRAERREN (1<<11) /* Frame error interrupt enable */
+#define UCR3_DSR (1<<10) /* Data set ready */
+#define UCR3_DCD (1<<9) /* Data carrier detect */
+#define UCR3_RI (1<<8) /* Ring indicator */
+#define UCR3_TIMEOUTEN (1<<7) /* Timeout interrupt enable */
+#define UCR3_RXDSEN (1<<6) /* Receive status interrupt enable */
+#define UCR3_AIRINTEN (1<<5) /* Async IR wake interrupt enable */
+#define UCR3_AWAKEN (1<<4) /* Async wake interrupt enable */
+#define UCR3_REF25 (1<<3) /* Ref freq 25 MHz */
+#define UCR3_REF30 (1<<2) /* Ref Freq 30 MHz */
+#define UCR3_INVT (1<<1) /* Inverted Infrared transmission */
+#define UCR3_BPEN (1<<0) /* Preset registers enable */
+#define UCR4_CTSTL_32 (32<<10) /* CTS trigger level (32 chars) */
+#define UCR4_INVR (1<<9) /* Inverted infrared reception */
+#define UCR4_ENIRI (1<<8) /* Serial infrared interrupt enable */
+#define UCR4_WKEN (1<<7) /* Wake interrupt enable */
+#define UCR4_REF16 (1<<6) /* Ref freq 16 MHz */
+#define UCR4_IRSC (1<<5) /* IR special case */
+#define UCR4_TCEN (1<<3) /* Transmit complete interrupt enable */
+#define UCR4_BKEN (1<<2) /* Break condition interrupt enable */
+#define UCR4_OREN (1<<1) /* Receiver overrun interrupt enable */
+#define UCR4_DREN (1<<0) /* Recv data ready interrupt enable */
+#define UFCR_RXTL_SHF 0 /* Receiver trigger level shift */
+#define UFCR_RFDIV (7<<7) /* Reference freq divider mask */
+#define UFCR_TXTL_SHF 10 /* Transmitter trigger level shift */
+#define USR1_PARITYERR (1<<15) /* Parity error interrupt flag */
+#define USR1_RTSS (1<<14) /* RTS pin status */
+#define USR1_TRDY (1<<13) /* Transmitter ready interrupt/dma flag */
+#define USR1_RTSD (1<<12) /* RTS delta */
+#define USR1_ESCF (1<<11) /* Escape seq interrupt flag */
+#define USR1_FRAMERR (1<<10) /* Frame error interrupt flag */
+#define USR1_RRDY (1<<9) /* Receiver ready interrupt/dma flag */
+#define USR1_TIMEOUT (1<<7) /* Receive timeout interrupt status */
+#define USR1_RXDS (1<<6) /* Receiver idle interrupt flag */
+#define USR1_AIRINT (1<<5) /* Async IR wake interrupt flag */
+#define USR1_AWAKE (1<<4) /* Aysnc wake interrupt flag */
+#define USR2_ADET (1<<15) /* Auto baud rate detect complete */
+#define USR2_TXFE (1<<14) /* Transmit buffer FIFO empty */
+#define USR2_DTRF (1<<13) /* DTR edge interrupt flag */
+#define USR2_IDLE (1<<12) /* Idle condition */
+#define USR2_IRINT (1<<8) /* Serial infrared interrupt flag */
+#define USR2_WAKE (1<<7) /* Wake */
+#define USR2_RTSF (1<<4) /* RTS edge interrupt flag */
+#define USR2_TXDC (1<<3) /* Transmitter complete */
+#define USR2_BRCD (1<<2) /* Break condition */
+#define USR2_ORE (1<<1) /* Overrun error */
+#define USR2_RDR (1<<0) /* Recv data ready */
+#define UTS_FRCPERR (1<<13) /* Force parity error */
+#define UTS_LOOP (1<<12) /* Loop tx and rx */
+#define UTS_TXEMPTY (1<<6) /* TxFIFO empty */
+#define UTS_RXEMPTY (1<<5) /* RxFIFO empty */
+#define UTS_TXFULL (1<<4) /* TxFIFO full */
+#define UTS_RXFULL (1<<3) /* RxFIFO full */
+#define UTS_SOFTRST (1<<0) /* Software reset */
+
/* We've been assigned a range on the "Low-density serial ports" major */
#define SERIAL_IMX_MAJOR 204
#define MINOR_START 41
@@ -128,7 +244,10 @@ static void imx_timeout(unsigned long data)
static void imx_stop_tx(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
- UCR1((u32)sport->port.membase) &= ~UCR1_TXMPTYEN;
+ unsigned long temp;
+
+ temp = readl(sport->port.membase + UCR1);
+ writel(temp & ~UCR1_TXMPTYEN, sport->port.membase + UCR1);
}
/*
@@ -137,7 +256,10 @@ static void imx_stop_tx(struct uart_port *port)
static void imx_stop_rx(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
- UCR2((u32)sport->port.membase) &= ~UCR2_RXEN;
+ unsigned long temp;
+
+ temp = readl(sport->port.membase + UCR2);
+ writel(temp &~ UCR2_RXEN, sport->port.membase + UCR2);
}
/*
@@ -154,10 +276,10 @@ static inline void imx_transmit_buffer(struct imx_port *sport)
{
struct circ_buf *xmit = &sport->port.info->xmit;
- while (!(UTS((u32)sport->port.membase) & UTS_TXFULL)) {
+ while (!(readl(sport->port.membase + UTS) & UTS_TXFULL)) {
/* send xmit->buf[xmit->tail]
* out the port here */
- URTX0((u32)sport->port.membase) = xmit->buf[xmit->tail];
+ writel(xmit->buf[xmit->tail], sport->port.membase + URTX0);
xmit->tail = (xmit->tail + 1) &
(UART_XMIT_SIZE - 1);
sport->port.icount.tx++;
@@ -175,21 +297,24 @@ static inline void imx_transmit_buffer(struct imx_port *sport)
static void imx_start_tx(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
+ unsigned long temp;
- UCR1((u32)sport->port.membase) |= UCR1_TXMPTYEN;
+ temp = readl(sport->port.membase + UCR1);
+ writel(temp | UCR1_TXMPTYEN, sport->port.membase + UCR1);
- imx_transmit_buffer(sport);
+ if (readl(sport->port.membase + UTS) & UTS_TXEMPTY)
+ imx_transmit_buffer(sport);
}
static irqreturn_t imx_rtsint(int irq, void *dev_id)
{
struct imx_port *sport = (struct imx_port *)dev_id;
- unsigned int val = USR1((u32)sport->port.membase)&USR1_RTSS;
+ unsigned int val = readl(sport->port.membase + USR1) & USR1_RTSS;
unsigned long flags;
spin_lock_irqsave(&sport->port.lock, flags);
- USR1((u32)sport->port.membase) = USR1_RTSD;
+ writel(USR1_RTSD, sport->port.membase + USR1);
uart_handle_cts_change(&sport->port, !!val);
wake_up_interruptible(&sport->port.info->delta_msr_wait);
@@ -207,7 +332,7 @@ static irqreturn_t imx_txint(int irq, void *dev_id)
if (sport->port.x_char)
{
/* Send next char */
- URTX0((u32)sport->port.membase) = sport->port.x_char;
+ writel(sport->port.x_char, sport->port.membase + URTX0);
goto out;
}
@@ -231,17 +356,18 @@ static irqreturn_t imx_rxint(int irq, void *dev_id)
struct imx_port *sport = dev_id;
unsigned int rx,flg,ignored = 0;
struct tty_struct *tty = sport->port.info->tty;
- unsigned long flags;
+ unsigned long flags, temp;
- rx = URXD0((u32)sport->port.membase);
+ rx = readl(sport->port.membase + URXD0);
spin_lock_irqsave(&sport->port.lock,flags);
do {
flg = TTY_NORMAL;
sport->port.icount.rx++;
- if( USR2((u32)sport->port.membase) & USR2_BRCD ) {
- USR2((u32)sport->port.membase) |= USR2_BRCD;
+ temp = readl(sport->port.membase + USR2);
+ if( temp & USR2_BRCD ) {
+ writel(temp | USR2_BRCD, sport->port.membase + USR2);
if(uart_handle_break(&sport->port))
goto ignore_char;
}
@@ -257,7 +383,7 @@ static irqreturn_t imx_rxint(int irq, void *dev_id)
tty_insert_flip_char(tty, rx, flg);
ignore_char:
- rx = URXD0((u32)sport->port.membase);
+ rx = readl(sport->port.membase + URXD0);
} while(rx & URXD_CHARRDY);
out:
@@ -301,7 +427,7 @@ static unsigned int imx_tx_empty(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
- return USR2((u32)sport->port.membase) & USR2_TXDC ? TIOCSER_TEMT : 0;
+ return (readl(sport->port.membase + USR2) & USR2_TXDC) ? TIOCSER_TEMT : 0;
}
/*
@@ -312,10 +438,10 @@ static unsigned int imx_get_mctrl(struct uart_port *port)
struct imx_port *sport = (struct imx_port *)port;
unsigned int tmp = TIOCM_DSR | TIOCM_CAR;
- if (USR1((u32)sport->port.membase) & USR1_RTSS)
+ if (readl(sport->port.membase + USR1) & USR1_RTSS)
tmp |= TIOCM_CTS;
- if (UCR2((u32)sport->port.membase) & UCR2_CTS)
+ if (readl(sport->port.membase + UCR2) & UCR2_CTS)
tmp |= TIOCM_RTS;
return tmp;
@@ -324,11 +450,14 @@ static unsigned int imx_get_mctrl(struct uart_port *port)
static void imx_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct imx_port *sport = (struct imx_port *)port;
+ unsigned long temp;
+
+ temp = readl(sport->port.membase + UCR2) & ~UCR2_CTS;
if (mctrl & TIOCM_RTS)
- UCR2((u32)sport->port.membase) |= UCR2_CTS;
- else
- UCR2((u32)sport->port.membase) &= ~UCR2_CTS;
+ temp |= UCR2_CTS;
+
+ writel(temp, sport->port.membase + UCR2);
}
/*
@@ -337,14 +466,16 @@ static void imx_set_mctrl(struct uart_port *port, unsigned int mctrl)
static void imx_break_ctl(struct uart_port *port, int break_state)
{
struct imx_port *sport = (struct imx_port *)port;
- unsigned long flags;
+ unsigned long flags, temp;
spin_lock_irqsave(&sport->port.lock, flags);
+ temp = readl(sport->port.membase + UCR1) & ~UCR1_SNDBRK;
+
if ( break_state != 0 )
- UCR1((u32)sport->port.membase) |= UCR1_SNDBRK;
- else
- UCR1((u32)sport->port.membase) &= ~UCR1_SNDBRK;
+ temp |= UCR1_SNDBRK;
+
+ writel(temp, sport->port.membase + UCR1);
spin_unlock_irqrestore(&sport->port.lock, flags);
}
@@ -360,7 +491,7 @@ static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
/* set receiver / transmitter trigger level.
* RFDIV is set such way to satisfy requested uartclk value
*/
- val = TXTL<<10 | RXTL;
+ val = TXTL << 10 | RXTL;
ufcr_rfdiv = (imx_get_perclk1() + sport->port.uartclk / 2) / sport->port.uartclk;
if(!ufcr_rfdiv)
@@ -373,7 +504,7 @@ static int imx_setup_ufcr(struct imx_port *sport, unsigned int mode)
val |= UFCR_RFDIV & (ufcr_rfdiv << 7);
- UFCR((u32)sport->port.membase) = val;
+ writel(val, sport->port.membase + UFCR);
return 0;
}
@@ -382,14 +513,15 @@ static int imx_startup(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
int retval;
- unsigned long flags;
+ unsigned long flags, temp;
imx_setup_ufcr(sport, 0);
/* disable the DREN bit (Data Ready interrupt enable) before
* requesting IRQs
*/
- UCR4((u32)sport->port.membase) &= ~UCR4_DREN;
+ temp = readl(sport->port.membase + UCR4);
+ writel(temp & ~UCR4_DREN, sport->port.membase + UCR4);
/*
* Allocate the IRQ
@@ -411,12 +543,16 @@ static int imx_startup(struct uart_port *port)
/*
* Finally, clear and enable interrupts
*/
+ writel(USR1_RTSD, sport->port.membase + USR1);
+
+ temp = readl(sport->port.membase + UCR1);
+ temp |= (UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+ writel(temp, sport->port.membase + UCR1);
- USR1((u32)sport->port.membase) = USR1_RTSD;
- UCR1((u32)sport->port.membase) |=
- (UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+ temp = readl(sport->port.membase + UCR2);
+ temp |= (UCR2_RXEN | UCR2_TXEN);
+ writel(temp, sport->port.membase + UCR2);
- UCR2((u32)sport->port.membase) |= (UCR2_RXEN | UCR2_TXEN);
/*
* Enable modem status interrupts
*/
@@ -437,6 +573,7 @@ error_out1:
static void imx_shutdown(struct uart_port *port)
{
struct imx_port *sport = (struct imx_port *)port;
+ unsigned long temp;
/*
* Stop our timer.
@@ -454,8 +591,9 @@ static void imx_shutdown(struct uart_port *port)
* Disable all interrupts, port and break condition.
*/
- UCR1((u32)sport->port.membase) &=
- ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+ temp = readl(sport->port.membase + UCR1);
+ temp &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN | UCR1_UARTEN);
+ writel(temp, sport->port.membase + UCR1);
}
static void
@@ -548,18 +686,18 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
/*
* disable interrupts and drain transmitter
*/
- old_ucr1 = UCR1((u32)sport->port.membase);
- UCR1((u32)sport->port.membase) &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
+ old_ucr1 = readl(sport->port.membase + UCR1);
+ writel(old_ucr1 & ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
+ sport->port.membase + UCR1);
- while ( !(USR2((u32)sport->port.membase) & USR2_TXDC))
+ while ( !(readl(sport->port.membase + USR2) & USR2_TXDC))
barrier();
/* then, disable everything */
- old_txrxen = UCR2((u32)sport->port.membase) & ( UCR2_TXEN | UCR2_RXEN );
- UCR2((u32)sport->port.membase) &= ~( UCR2_TXEN | UCR2_RXEN);
-
- /* set the parity, stop bits and data size */
- UCR2((u32)sport->port.membase) = ucr2;
+ old_txrxen = readl(sport->port.membase + UCR2);
+ writel(old_txrxen & ~( UCR2_TXEN | UCR2_RXEN),
+ sport->port.membase + UCR2);
+ old_txrxen &= (UCR2_TXEN | UCR2_RXEN);
/* set the baud rate. We assume uartclk = 16 MHz
*
@@ -567,11 +705,13 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
* --------- = --------
* uartclk UBMR - 1
*/
- UBIR((u32)sport->port.membase) = (baud / 100) - 1;
- UBMR((u32)sport->port.membase) = 10000 - 1;
+ writel((baud / 100) - 1, sport->port.membase + UBIR);
+ writel(10000 - 1, sport->port.membase + UBMR);
+
+ writel(old_ucr1, sport->port.membase + UCR1);
- UCR1((u32)sport->port.membase) = old_ucr1;
- UCR2((u32)sport->port.membase) |= old_txrxen;
+ /* set the parity, stop bits and data size */
+ writel(ucr2 | old_txrxen, sport->port.membase + UCR2);
if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
imx_enable_ms(&sport->port);
@@ -730,9 +870,11 @@ static void __init imx_init_ports(void)
static void imx_console_putchar(struct uart_port *port, int ch)
{
struct imx_port *sport = (struct imx_port *)port;
- while ((UTS((u32)sport->port.membase) & UTS_TXFULL))
+
+ while (readl(sport->port.membase + UTS) & UTS_TXFULL)
barrier();
- URTX0((u32)sport->port.membase) = ch;
+
+ writel(ch, sport->port.membase + URTX0);
}
/*
@@ -747,13 +889,14 @@ imx_console_write(struct console *co, const char *s, unsigned int count)
/*
* First, save UCR1/2 and then disable interrupts
*/
- old_ucr1 = UCR1((u32)sport->port.membase);
- old_ucr2 = UCR2((u32)sport->port.membase);
+ old_ucr1 = readl(sport->port.membase + UCR1);
+ old_ucr2 = readl(sport->port.membase + UCR2);
- UCR1((u32)sport->port.membase) =
- (old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN)
- & ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
- UCR2((u32)sport->port.membase) = old_ucr2 | UCR2_TXEN;
+ writel((old_ucr1 | UCR1_UARTCLKEN | UCR1_UARTEN) &
+ ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN),
+ sport->port.membase + UCR1);
+
+ writel(old_ucr2 | UCR2_TXEN, sport->port.membase + UCR2);
uart_console_write(&sport->port, s, count, imx_console_putchar);
@@ -761,10 +904,10 @@ imx_console_write(struct console *co, const char *s, unsigned int count)
* Finally, wait for transmitter to become empty
* and restore UCR1/2
*/
- while (!(USR2((u32)sport->port.membase) & USR2_TXDC));
+ while (!(readl(sport->port.membase + USR2) & USR2_TXDC));
- UCR1((u32)sport->port.membase) = old_ucr1;
- UCR2((u32)sport->port.membase) = old_ucr2;
+ writel(old_ucr1, sport->port.membase + UCR1);
+ writel(old_ucr2, sport->port.membase + UCR2);
}
/*
@@ -776,13 +919,13 @@ imx_console_get_options(struct imx_port *sport, int *baud,
int *parity, int *bits)
{
- if ( UCR1((u32)sport->port.membase) | UCR1_UARTEN ) {
+ if ( readl(sport->port.membase + UCR1) | UCR1_UARTEN ) {
/* ok, the port was enabled */
unsigned int ucr2, ubir,ubmr, uartclk;
unsigned int baud_raw;
unsigned int ucfr_rfdiv;
- ucr2 = UCR2((u32)sport->port.membase);
+ ucr2 = readl(sport->port.membase + UCR2);
*parity = 'n';
if (ucr2 & UCR2_PREN) {
@@ -797,11 +940,10 @@ imx_console_get_options(struct imx_port *sport, int *baud,
else
*bits = 7;
- ubir = UBIR((u32)sport->port.membase) & 0xffff;
- ubmr = UBMR((u32)sport->port.membase) & 0xffff;
-
+ ubir = readl(sport->port.membase + UBIR) & 0xffff;
+ ubmr = readl(sport->port.membase + UBMR) & 0xffff;
- ucfr_rfdiv = (UFCR((u32)sport->port.membase) & UFCR_RFDIV) >> 7;
+ ucfr_rfdiv = (readl(sport->port.membase + UFCR) & UFCR_RFDIV) >> 7;
if (ucfr_rfdiv == 6)
ucfr_rfdiv = 7;
else
diff --git a/drivers/serial/jsm/jsm_neo.c b/drivers/serial/jsm/jsm_neo.c
index 8be8da37f62..b2d6f5b1a7c 100644
--- a/drivers/serial/jsm/jsm_neo.c
+++ b/drivers/serial/jsm/jsm_neo.c
@@ -581,8 +581,13 @@ static void neo_parse_modem(struct jsm_channel *ch, u8 signals)
return;
/* Scrub off lower bits. They signify delta's, which I don't care about */
- msignals &= 0xf0;
+ /* Keep DDCD and DDSR though */
+ msignals &= 0xf8;
+ if (msignals & UART_MSR_DDCD)
+ uart_handle_dcd_change(&ch->uart_port, msignals & UART_MSR_DCD);
+ if (msignals & UART_MSR_DDSR)
+ uart_handle_cts_change(&ch->uart_port, msignals & UART_MSR_CTS);
if (msignals & UART_MSR_DCD)
ch->ch_mistat |= UART_MSR_DCD;
else
diff --git a/drivers/serial/jsm/jsm_tty.c b/drivers/serial/jsm/jsm_tty.c
index be22bbdbc8e..281f23a371b 100644
--- a/drivers/serial/jsm/jsm_tty.c
+++ b/drivers/serial/jsm/jsm_tty.c
@@ -448,6 +448,7 @@ int jsm_uart_port_init(struct jsm_board *brd)
continue;
brd->channels[i]->uart_port.irq = brd->irq;
+ brd->channels[i]->uart_port.uartclk = 14745600;
brd->channels[i]->uart_port.type = PORT_JSM;
brd->channels[i]->uart_port.iotype = UPIO_MEM;
brd->channels[i]->uart_port.membase = brd->re_map_membase;
diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c
index 8d24cd52105..35f8b86cc78 100644
--- a/drivers/serial/mpc52xx_uart.c
+++ b/drivers/serial/mpc52xx_uart.c
@@ -257,9 +257,10 @@ mpc52xx_uart_shutdown(struct uart_port *port)
{
struct mpc52xx_psc __iomem *psc = PSC(port);
- /* Shut down the port, interrupt and all */
+ /* Shut down the port. Leave TX active if on a console port */
out_8(&psc->command,MPC52xx_PSC_RST_RX);
- out_8(&psc->command,MPC52xx_PSC_RST_TX);
+ if (!uart_console(port))
+ out_8(&psc->command,MPC52xx_PSC_RST_TX);
port->read_status_mask = 0;
out_be16(&psc->mpc52xx_psc_imr,port->read_status_mask);
@@ -1069,7 +1070,7 @@ mpc52xx_uart_of_enumerate(void)
continue;
/* Is a particular device number requested? */
- devno = get_property(np, "port-number", NULL);
+ devno = of_get_property(np, "port-number", NULL);
mpc52xx_uart_of_assign(of_node_get(np), devno ? *devno : -1);
}
diff --git a/drivers/serial/mpsc.c b/drivers/serial/mpsc.c
index 3d2fcc57b1c..d09f2097d5b 100644
--- a/drivers/serial/mpsc.c
+++ b/drivers/serial/mpsc.c
@@ -183,6 +183,7 @@ struct mpsc_port_info {
u8 *txb_p; /* Phys addr of txb */
int txr_head; /* Where new data goes */
int txr_tail; /* Where sent data comes off */
+ spinlock_t tx_lock; /* transmit lock */
/* Mirrored values of regs we can't read (if 'mirror_regs' set) */
u32 MPSC_MPCR_m;
@@ -1212,6 +1213,9 @@ mpsc_tx_intr(struct mpsc_port_info *pi)
{
struct mpsc_tx_desc *txre;
int rc = 0;
+ unsigned long iflags;
+
+ spin_lock_irqsave(&pi->tx_lock, iflags);
if (!mpsc_sdma_tx_active(pi)) {
txre = (struct mpsc_tx_desc *)(pi->txr +
@@ -1248,6 +1252,7 @@ mpsc_tx_intr(struct mpsc_port_info *pi)
mpsc_sdma_start_tx(pi); /* start next desc if ready */
}
+ spin_unlock_irqrestore(&pi->tx_lock, iflags);
return rc;
}
@@ -1338,11 +1343,16 @@ static void
mpsc_start_tx(struct uart_port *port)
{
struct mpsc_port_info *pi = (struct mpsc_port_info *)port;
+ unsigned long iflags;
+
+ spin_lock_irqsave(&pi->tx_lock, iflags);
mpsc_unfreeze(pi);
mpsc_copy_tx_data(pi);
mpsc_sdma_start_tx(pi);
+ spin_unlock_irqrestore(&pi->tx_lock, iflags);
+
pr_debug("mpsc_start_tx[%d]\n", port->line);
return;
}
@@ -1625,6 +1635,16 @@ mpsc_console_write(struct console *co, const char *s, uint count)
struct mpsc_port_info *pi = &mpsc_ports[co->index];
u8 *bp, *dp, add_cr = 0;
int i;
+ unsigned long iflags;
+
+ spin_lock_irqsave(&pi->tx_lock, iflags);
+
+ while (pi->txr_head != pi->txr_tail) {
+ while (mpsc_sdma_tx_active(pi))
+ udelay(100);
+ mpsc_sdma_intr_ack(pi);
+ mpsc_tx_intr(pi);
+ }
while (mpsc_sdma_tx_active(pi))
udelay(100);
@@ -1668,6 +1688,7 @@ mpsc_console_write(struct console *co, const char *s, uint count)
pi->txr_tail = (pi->txr_tail + 1) & (MPSC_TXR_ENTRIES - 1);
}
+ spin_unlock_irqrestore(&pi->tx_lock, iflags);
return;
}
@@ -2005,7 +2026,8 @@ mpsc_drv_probe(struct platform_device *dev)
if (!(rc = mpsc_drv_map_regs(pi, dev))) {
mpsc_drv_get_platform_data(pi, dev, dev->id);
- if (!(rc = mpsc_make_ready(pi)))
+ if (!(rc = mpsc_make_ready(pi))) {
+ spin_lock_init(&pi->tx_lock);
if (!(rc = uart_add_one_port(&mpsc_reg,
&pi->port)))
rc = 0;
@@ -2014,6 +2036,7 @@ mpsc_drv_probe(struct platform_device *dev)
(struct uart_port *)pi);
mpsc_drv_unmap_regs(pi);
}
+ }
else
mpsc_drv_unmap_regs(pi);
}
diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c
index 09b0b736a75..7ffdaeaf054 100644
--- a/drivers/serial/of_serial.c
+++ b/drivers/serial/of_serial.c
@@ -29,8 +29,8 @@ static int __devinit of_platform_serial_setup(struct of_device *ofdev,
int ret;
memset(port, 0, sizeof *port);
- spd = get_property(np, "current-speed", NULL);
- clk = get_property(np, "clock-frequency", NULL);
+ spd = of_get_property(np, "current-speed", NULL);
+ clk = of_get_property(np, "clock-frequency", NULL);
if (!clk) {
dev_warn(&ofdev->dev, "no clock-frequency property set\n");
return -ENODEV;
@@ -48,7 +48,8 @@ static int __devinit of_platform_serial_setup(struct of_device *ofdev,
port->iotype = UPIO_MEM;
port->type = type;
port->uartclk = *clk;
- port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP;
+ port->flags = UPF_SHARE_IRQ | UPF_BOOT_AUTOCONF | UPF_IOREMAP
+ | UPF_FIXED_PORT;
port->dev = &ofdev->dev;
port->custom_divisor = *clk / (16 * (*spd));
diff --git a/drivers/serial/pmac_zilog.c b/drivers/serial/pmac_zilog.c
index 752ef07516b..0fa9f676176 100644
--- a/drivers/serial/pmac_zilog.c
+++ b/drivers/serial/pmac_zilog.c
@@ -1450,14 +1450,14 @@ no_dma:
/*
* Detect port type
*/
- if (device_is_compatible(np, "cobalt"))
+ if (of_device_is_compatible(np, "cobalt"))
uap->flags |= PMACZILOG_FLAG_IS_INTMODEM;
- conn = get_property(np, "AAPL,connector", &len);
+ conn = of_get_property(np, "AAPL,connector", &len);
if (conn && (strcmp(conn, "infrared") == 0))
uap->flags |= PMACZILOG_FLAG_IS_IRDA;
uap->port_type = PMAC_SCC_ASYNC;
/* 1999 Powerbook G3 has slot-names property instead */
- slots = get_property(np, "slot-names", &len);
+ slots = of_get_property(np, "slot-names", &len);
if (slots && slots->count > 0) {
if (strcmp(slots->name, "IrDA") == 0)
uap->flags |= PMACZILOG_FLAG_IS_IRDA;
@@ -1467,10 +1467,11 @@ no_dma:
if (ZS_IS_IRDA(uap))
uap->port_type = PMAC_SCC_IRDA;
if (ZS_IS_INTMODEM(uap)) {
- struct device_node* i2c_modem = find_devices("i2c-modem");
+ struct device_node* i2c_modem =
+ of_find_node_by_name(NULL, "i2c-modem");
if (i2c_modem) {
const char* mid =
- get_property(i2c_modem, "modem-id", NULL);
+ of_get_property(i2c_modem, "modem-id", NULL);
if (mid) switch(*mid) {
case 0x04 :
case 0x05 :
@@ -1482,6 +1483,7 @@ no_dma:
}
printk(KERN_INFO "pmac_zilog: i2c-modem detected, id: %d\n",
mid ? (*mid) : 0);
+ of_node_put(i2c_modem);
} else {
printk(KERN_INFO "pmac_zilog: serial modem detected\n");
}
diff --git a/drivers/serial/pxa.c b/drivers/serial/pxa.c
index d403aaa5509..e9c6cb391a2 100644
--- a/drivers/serial/pxa.c
+++ b/drivers/serial/pxa.c
@@ -717,7 +717,7 @@ struct uart_ops serial_pxa_pops = {
static struct uart_pxa_port serial_pxa_ports[] = {
{ /* FFUART */
.name = "FFUART",
- .cken = CKEN6_FFUART,
+ .cken = CKEN_FFUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
@@ -731,7 +731,7 @@ static struct uart_pxa_port serial_pxa_ports[] = {
},
}, { /* BTUART */
.name = "BTUART",
- .cken = CKEN7_BTUART,
+ .cken = CKEN_BTUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
@@ -745,7 +745,7 @@ static struct uart_pxa_port serial_pxa_ports[] = {
},
}, { /* STUART */
.name = "STUART",
- .cken = CKEN5_STUART,
+ .cken = CKEN_STUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
@@ -759,7 +759,7 @@ static struct uart_pxa_port serial_pxa_ports[] = {
},
}, { /* HWUART */
.name = "HWUART",
- .cken = CKEN4_HWUART,
+ .cken = CKEN_HWUART,
.port = {
.type = PORT_PXA,
.iotype = UPIO_MEM,
diff --git a/drivers/serial/s3c2410.c b/drivers/serial/s3c2410.c
index 3ba9208ebd0..10bc0209cd6 100644
--- a/drivers/serial/s3c2410.c
+++ b/drivers/serial/s3c2410.c
@@ -957,7 +957,7 @@ static struct uart_driver s3c24xx_uart_drv = {
static struct s3c24xx_uart_port s3c24xx_serial_ports[NR_PORTS] = {
[0] = {
.port = {
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[0].port.lock),
.iotype = UPIO_MEM,
.irq = IRQ_S3CUART_RX0,
.uartclk = 0,
@@ -969,7 +969,7 @@ static struct s3c24xx_uart_port s3c24xx_serial_ports[NR_PORTS] = {
},
[1] = {
.port = {
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[1].port.lock),
.iotype = UPIO_MEM,
.irq = IRQ_S3CUART_RX1,
.uartclk = 0,
@@ -983,7 +983,7 @@ static struct s3c24xx_uart_port s3c24xx_serial_ports[NR_PORTS] = {
[2] = {
.port = {
- .lock = SPIN_LOCK_UNLOCKED,
+ .lock = __SPIN_LOCK_UNLOCKED(s3c24xx_serial_ports[2].port.lock),
.iotype = UPIO_MEM,
.irq = IRQ_S3CUART_RX2,
.uartclk = 0,
diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c
index 0422c0f1f85..326020f86f7 100644
--- a/drivers/serial/serial_core.c
+++ b/drivers/serial/serial_core.c
@@ -37,13 +37,6 @@
#include <asm/irq.h>
#include <asm/uaccess.h>
-#undef DEBUG
-#ifdef DEBUG
-#define DPRINTK(x...) printk(x)
-#else
-#define DPRINTK(x...) do { } while (0)
-#endif
-
/*
* This is used to lock changes in serial line configuration.
*/
@@ -552,7 +545,7 @@ static void uart_flush_buffer(struct tty_struct *tty)
return;
}
- DPRINTK("uart_flush_buffer(%d) called\n", tty->index);
+ pr_debug("uart_flush_buffer(%d) called\n", tty->index);
spin_lock_irqsave(&port->lock, flags);
uart_circ_clear(&state->info->xmit);
@@ -672,19 +665,21 @@ static int uart_set_info(struct uart_state *state,
*/
mutex_lock(&state->mutex);
- change_irq = new_serial.irq != port->irq;
+ change_irq = !(port->flags & UPF_FIXED_PORT)
+ && new_serial.irq != port->irq;
/*
* Since changing the 'type' of the port changes its resource
* allocations, we should treat type changes the same as
* IO port changes.
*/
- change_port = new_port != port->iobase ||
- (unsigned long)new_serial.iomem_base != port->mapbase ||
- new_serial.hub6 != port->hub6 ||
- new_serial.io_type != port->iotype ||
- new_serial.iomem_reg_shift != port->regshift ||
- new_serial.type != port->type;
+ change_port = !(port->flags & UPF_FIXED_PORT)
+ && (new_port != port->iobase ||
+ (unsigned long)new_serial.iomem_base != port->mapbase ||
+ new_serial.hub6 != port->hub6 ||
+ new_serial.io_type != port->iotype ||
+ new_serial.iomem_reg_shift != port->regshift ||
+ new_serial.type != port->type);
old_flags = port->flags;
new_flags = new_serial.flags;
@@ -796,8 +791,10 @@ static int uart_set_info(struct uart_state *state,
}
}
- port->irq = new_serial.irq;
- port->uartclk = new_serial.baud_base * 16;
+ if (change_irq)
+ port->irq = new_serial.irq;
+ if (!(port->flags & UPF_FIXED_PORT))
+ port->uartclk = new_serial.baud_base * 16;
port->flags = (port->flags & ~UPF_CHANGE_MASK) |
(new_flags & UPF_CHANGE_MASK);
port->custom_divisor = new_serial.custom_divisor;
@@ -1220,7 +1217,7 @@ static void uart_close(struct tty_struct *tty, struct file *filp)
port = state->port;
- DPRINTK("uart_close(%d) called\n", port->line);
+ pr_debug("uart_close(%d) called\n", port->line);
mutex_lock(&state->mutex);
@@ -1339,7 +1336,7 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout)
expire = jiffies + timeout;
- DPRINTK("uart_wait_until_sent(%d), jiffies=%lu, expire=%lu...\n",
+ pr_debug("uart_wait_until_sent(%d), jiffies=%lu, expire=%lu...\n",
port->line, jiffies, expire);
/*
@@ -1368,7 +1365,7 @@ static void uart_hangup(struct tty_struct *tty)
struct uart_state *state = tty->driver_data;
BUG_ON(!kernel_locked());
- DPRINTK("uart_hangup(%d)\n", state->port->line);
+ pr_debug("uart_hangup(%d)\n", state->port->line);
mutex_lock(&state->mutex);
if (state->info && state->info->flags & UIF_NORMAL_ACTIVE) {
@@ -1566,7 +1563,7 @@ static int uart_open(struct tty_struct *tty, struct file *filp)
int retval, line = tty->index;
BUG_ON(!kernel_locked());
- DPRINTK("uart_open(%d) called\n", line);
+ pr_debug("uart_open(%d) called\n", line);
/*
* tty->driver->num won't change, so we won't fail here with
@@ -2064,6 +2061,7 @@ uart_report_port(struct uart_driver *drv, struct uart_port *port)
case UPIO_MEM32:
case UPIO_AU:
case UPIO_TSI:
+ case UPIO_DWAPB:
snprintf(address, sizeof(address),
"MMIO 0x%lx", port->mapbase);
break;
@@ -2409,6 +2407,7 @@ int uart_match_port(struct uart_port *port1, struct uart_port *port2)
case UPIO_MEM32:
case UPIO_AU:
case UPIO_TSI:
+ case UPIO_DWAPB:
return (port1->mapbase == port2->mapbase);
}
return 0;
diff --git a/drivers/serial/serial_txx9.c b/drivers/serial/serial_txx9.c
index 509ace7e688..1deb5764326 100644
--- a/drivers/serial/serial_txx9.c
+++ b/drivers/serial/serial_txx9.c
@@ -15,31 +15,6 @@
* published by the Free Software Foundation.
*
* Serial driver for TX3927/TX4927/TX4925/TX4938 internal SIO controller
- *
- * Revision History:
- * 0.30 Initial revision. (Renamed from serial_txx927.c)
- * 0.31 Use save_flags instead of local_irq_save.
- * 0.32 Support SCLK.
- * 0.33 Switch TXX9_TTY_NAME by CONFIG_SERIAL_TXX9_STDSERIAL.
- * Support TIOCSERGETLSR.
- * 0.34 Support slow baudrate.
- * 0.40 Merge codes from mainstream kernel (2.4.22).
- * 0.41 Fix console checking in rs_shutdown_port().
- * Disable flow-control in serial_console_write().
- * 0.42 Fix minor compiler warning.
- * 1.00 Kernel 2.6. Converted to new serial core (based on 8250.c).
- * 1.01 Set fifosize to make tx_empry called properly.
- * Use standard uart_get_divisor.
- * 1.02 Cleanup. (import 8250.c changes)
- * 1.03 Fix low-latency mode. (import 8250.c changes)
- * 1.04 Remove usage of deprecated functions, cleanup.
- * 1.05 More strict check in verify_port. Cleanup.
- * 1.06 Do not insert a char caused previous overrun.
- * Fix some spin_locks.
- * Do not call uart_add_one_port for absent ports.
- * 1.07 Use CONFIG_SERIAL_TXX9_NR_UARTS. Cleanup.
- * 1.08 Use platform_device.
- * Fix and cleanup suspend/resume/initialization codes.
*/
#if defined(CONFIG_SERIAL_TXX9_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ)
@@ -62,7 +37,7 @@
#include <asm/io.h>
-static char *serial_version = "1.08";
+static char *serial_version = "1.09";
static char *serial_name = "TX39/49 Serial driver";
#define PASS_LIMIT 256
@@ -70,13 +45,14 @@ static char *serial_name = "TX39/49 Serial driver";
#if !defined(CONFIG_SERIAL_TXX9_STDSERIAL)
/* "ttyS" is used for standard serial driver */
#define TXX9_TTY_NAME "ttyTX"
-#define TXX9_TTY_MINOR_START (64 + 64) /* ttyTX0(128), ttyTX1(129) */
+#define TXX9_TTY_MINOR_START 196
+#define TXX9_TTY_MAJOR 204
#else
/* acts like standard serial driver */
#define TXX9_TTY_NAME "ttyS"
#define TXX9_TTY_MINOR_START 64
-#endif
#define TXX9_TTY_MAJOR TTY_MAJOR
+#endif
/* flag aliases */
#define UPF_TXX9_HAVE_CTS_LINE UPF_BUGGY_UART
diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c
index 46c40bbc4bc..1f89496d530 100644
--- a/drivers/serial/sh-sci.c
+++ b/drivers/serial/sh-sci.c
@@ -46,6 +46,7 @@
#endif
#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+#include <linux/ctype.h>
#include <asm/clock.h>
#include <asm/sh_bios.h>
#include <asm/kgdb.h>
@@ -61,7 +62,7 @@ struct sci_port {
unsigned int type;
/* Port IRQs: ERI, RXI, TXI, BRI (optional) */
- unsigned int irqs[SCIx_NR_IRQS];
+ unsigned int irqs[SCIx_NR_IRQS];
/* Port pin configuration */
void (*init_pins)(struct uart_port *port,
@@ -76,6 +77,11 @@ struct sci_port {
/* Break timer */
struct timer_list break_timer;
int break_flag;
+
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+ /* Port clock */
+ struct clk *clk;
+#endif
};
#ifdef CONFIG_SH_KGDB
@@ -163,7 +169,7 @@ static void put_string(struct sci_port *sci_port, const char *buffer, int count)
usegdb |= sh_bios_in_gdb_mode();
#endif
#ifdef CONFIG_SH_KGDB
- usegdb |= (kgdb_in_gdb_mode && (port == kgdb_sci_port));
+ usegdb |= (kgdb_in_gdb_mode && (sci_port == kgdb_sci_port));
#endif
if (usegdb) {
@@ -204,7 +210,7 @@ static int kgdb_sci_getchar(void)
int c;
/* Keep trying to read a character, this could be neater */
- while ((c = get_char(kgdb_sci_port)) < 0)
+ while ((c = get_char(&kgdb_sci_port->port)) < 0)
cpu_relax();
return c;
@@ -212,7 +218,7 @@ static int kgdb_sci_getchar(void)
static inline void kgdb_sci_putchar(int c)
{
- put_char(kgdb_sci_port, c);
+ put_char(&kgdb_sci_port->port, c);
}
#endif /* CONFIG_SH_KGDB */
@@ -283,12 +289,23 @@ static void sci_init_pins_irda(struct uart_port *port, unsigned int cflag)
#endif
#if defined(SCIF_ONLY) || defined(SCI_AND_SCIF)
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7710)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300)
/* SH7300 doesn't use RTS/CTS */
static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
{
sci_out(port, SCFCR, 0);
}
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
+static void sci_init_pins_scif(struct uart_port* port, unsigned int cflag)
+{
+ unsigned int fcr_val = 0;
+
+ set_sh771x_scif_pfc(port);
+ if (cflag & CRTSCTS) {
+ fcr_val |= SCFCR_MCE;
+ }
+ sci_out(port, SCFCR, fcr_val);
+}
#elif defined(CONFIG_CPU_SH3)
/* For SH7705, SH7706, SH7707, SH7709, SH7709A, SH7729 */
static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
@@ -350,7 +367,7 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
} else {
#ifdef CONFIG_CPU_SUBTYPE_SH7343
/* Nothing */
-#elif defined(CONFIG_CPU_SUBTYPE_SH7780)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7780) || defined(CONFIG_CPU_SUBTYPE_SH7785)
ctrl_outw(0x0080, SCSPTR0); /* Set RTS = 1 */
#else
ctrl_outw(0x0080, SCSPTR2); /* Set RTS = 1 */
@@ -360,7 +377,9 @@ static void sci_init_pins_scif(struct uart_port *port, unsigned int cflag)
}
#endif
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7785)
static inline int scif_txroom(struct uart_port *port)
{
return SCIF_TXROOM_MAX - (sci_in(port, SCTFDR) & 0x7f);
@@ -735,12 +754,6 @@ static irqreturn_t sci_br_interrupt(int irq, void *ptr)
/* Handle BREAKs */
sci_handle_breaks(port);
-
-#ifdef CONFIG_SH_KGDB
- /* Break into the debugger if a break is detected */
- BREAKPOINT();
-#endif
-
sci_out(port, SCxSR, SCxSR_BREAK_CLEAR(port));
return IRQ_HANDLED;
@@ -947,6 +960,10 @@ static int sci_startup(struct uart_port *port)
if (s->enable)
s->enable(port);
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+ s->clk = clk_get(NULL, "module_clk");
+#endif
+
sci_request_irq(s);
sci_start_tx(port);
sci_start_rx(port, 1);
@@ -964,6 +981,11 @@ static void sci_shutdown(struct uart_port *port)
if (s->disable)
s->disable(port);
+
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+ clk_put(s->clk);
+ s->clk = NULL;
+#endif
}
static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
@@ -971,7 +993,6 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
{
struct sci_port *s = &sci_ports[port->line];
unsigned int status, baud, smr_val;
- unsigned long flags;
int t;
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16);
@@ -983,18 +1004,14 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
default:
{
#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
- struct clk *clk = clk_get(NULL, "module_clk");
- t = SCBRR_VALUE(baud, clk_get_rate(clk));
- clk_put(clk);
+ t = SCBRR_VALUE(baud, clk_get_rate(s->clk));
#else
t = SCBRR_VALUE(baud);
#endif
- }
break;
+ }
}
- spin_lock_irqsave(&port->lock, flags);
-
do {
status = sci_in(port, SCxSR);
} while (!(status & SCxSR_TEND(port)));
@@ -1038,8 +1055,6 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
if ((termios->c_cflag & CREAD) != 0)
sci_start_rx(port,0);
-
- spin_unlock_irqrestore(&port->lock, flags);
}
static const char *sci_type(struct uart_port *port)
@@ -1220,10 +1235,13 @@ static int __init serial_console_setup(struct console *co, char *options)
if (!port->membase || !port->mapbase)
return -ENODEV;
- spin_lock_init(&port->lock);
-
port->type = serial_console_port->type;
+#if defined(CONFIG_SUPERH) && !defined(CONFIG_SUPERH64)
+ if (!serial_console_port->clk)
+ serial_console_port->clk = clk_get(NULL, "module_clk");
+#endif
+
if (port->flags & UPF_IOREMAP)
sci_config_port(port, 0);
@@ -1247,7 +1265,7 @@ static struct console serial_console = {
.device = uart_console_device,
.write = serial_console_write,
.setup = serial_console_setup,
- .flags = CON_PRINTBUFFER,
+ .flags = CON_PRINTBUFFER,
.index = -1,
.data = &sci_uart_driver,
};
@@ -1292,11 +1310,23 @@ int __init kgdb_console_setup(struct console *co, char *options)
int parity = 'n';
int flow = 'n';
- spin_lock_init(&port->lock);
-
if (co->index != kgdb_portnum)
co->index = kgdb_portnum;
+ kgdb_sci_port = &sci_ports[co->index];
+ port = &kgdb_sci_port->port;
+
+ /*
+ * Also need to check port->type, we don't actually have any
+ * UPIO_PORT ports, but uart_report_port() handily misreports
+ * it anyways if we don't have a port available by the time this is
+ * called.
+ */
+ if (!port->type)
+ return -ENODEV;
+ if (!port->membase || !port->mapbase)
+ return -ENODEV;
+
if (options)
uart_parse_options(options, &baud, &parity, &bits, &flow);
else
@@ -1311,11 +1341,12 @@ int __init kgdb_console_setup(struct console *co, char *options)
#ifdef CONFIG_SH_KGDB_CONSOLE
static struct console kgdb_console = {
- .name = "ttySC",
- .write = kgdb_console_write,
- .setup = kgdb_console_setup,
- .flags = CON_PRINTBUFFER | CON_ENABLED,
- .index = -1,
+ .name = "ttySC",
+ .device = uart_console_device,
+ .write = kgdb_console_write,
+ .setup = kgdb_console_setup,
+ .flags = CON_PRINTBUFFER,
+ .index = -1,
.data = &sci_uart_driver,
};
@@ -1361,9 +1392,19 @@ static int __devinit sci_probe(struct platform_device *dev)
struct plat_sci_port *p = dev->dev.platform_data;
int i;
- for (i = 0; p && p->flags != 0 && i < SCI_NPORTS; p++, i++) {
+ for (i = 0; p && p->flags != 0; p++, i++) {
struct sci_port *sciport = &sci_ports[i];
+ /* Sanity check */
+ if (unlikely(i == SCI_NPORTS)) {
+ dev_notice(&dev->dev, "Attempting to register port "
+ "%d when only %d are available.\n",
+ i+1, SCI_NPORTS);
+ dev_notice(&dev->dev, "Consider bumping "
+ "CONFIG_SERIAL_SH_SCI_NR_UARTS!\n");
+ break;
+ }
+
sciport->port.mapbase = p->mapbase;
/*
@@ -1386,6 +1427,12 @@ static int __devinit sci_probe(struct platform_device *dev)
uart_add_one_port(&sci_uart_driver, &sciport->port);
}
+#if defined(CONFIG_SH_KGDB) && !defined(CONFIG_SH_KGDB_CONSOLE)
+ kgdb_sci_port = &sci_ports[kgdb_portnum];
+ kgdb_getchar = kgdb_sci_getchar;
+ kgdb_putchar = kgdb_sci_putchar;
+#endif
+
#ifdef CONFIG_CPU_FREQ
cpufreq_register_notifier(&sci_nb, CPUFREQ_TRANSITION_NOTIFIER);
dev_info(&dev->dev, "sci: CPU frequency notifier registered\n");
diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h
index 77f7d6351ab..fb04fb5f984 100644
--- a/drivers/serial/sh-sci.h
+++ b/drivers/serial/sh-sci.h
@@ -73,9 +73,13 @@
# define SCPDR 0xA4050136 /* 16 bit SCIF */
# define SCSCR_INIT(port) 0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
# define SCIF_ONLY
-#elif defined(CONFIG_CPU_SUBTYPE_SH7710)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
# define SCSPTR0 0xA4400000 /* 16 bit SCIF */
-# define SCSCR_INIT(port) 0x0030 /* TIE=0,RIE=0,TE=1,RE=1 */
+# define SCI_NPORTS 2
+# define SCIF_ORER 0x0001 /* overrun error bit */
+# define PACR 0xa4050100
+# define PBCR 0xa4050102
+# define SCSCR_INIT(port) 0x3B
# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH73180)
# define SCPDR 0xA4050138 /* 16 bit SCIF */
@@ -140,6 +144,16 @@
# define SCIF_ORER 0x0001 /* Overrun error bit */
# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
# define SCIF_ONLY
+#elif defined(CONFIG_CPU_SUBTYPE_SH7785)
+# define SCSPTR0 0xffea0024 /* 16 bit SCIF */
+# define SCSPTR1 0xffeb0024 /* 16 bit SCIF */
+# define SCSPTR2 0xffec0024 /* 16 bit SCIF */
+# define SCSPTR3 0xffed0024 /* 16 bit SCIF */
+# define SCSPTR4 0xffee0024 /* 16 bit SCIF */
+# define SCSPTR5 0xffef0024 /* 16 bit SCIF */
+# define SCIF_OPER 0x0001 /* Overrun error bit */
+# define SCSCR_INIT(port) 0x3a /* TIE=0,RIE=0,TE=1,RE=1,REIE=1 */
+# define SCIF_ONLY
#elif defined(CONFIG_CPU_SUBTYPE_SH7206)
# define SCSPTR0 0xfffe8020 /* 16 bit SCIF */
# define SCSPTR1 0xfffe8820 /* 16 bit SCIF */
@@ -163,7 +177,10 @@
#define SCI_CTRL_FLAGS_RIE 0x40 /* all */
#define SCI_CTRL_FLAGS_TE 0x20 /* all */
#define SCI_CTRL_FLAGS_RE 0x10 /* all */
-#if defined(CONFIG_CPU_SUBTYPE_SH7750) || defined(CONFIG_CPU_SUBTYPE_SH7751) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7750) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7751) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7785)
#define SCI_CTRL_FLAGS_REIE 0x08 /* 7750 SCIF */
#else
#define SCI_CTRL_FLAGS_REIE 0
@@ -333,9 +350,15 @@
}
#ifdef CONFIG_CPU_SH3
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
- defined(CONFIG_CPU_SUBTYPE_SH7705) || \
- defined(CONFIG_CPU_SUBTYPE_SH7710)
+#if defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
+#define SCIx_FNS(name, sh3_sci_offset, sh3_sci_size, sh4_sci_offset, sh4_sci_size, \
+ sh3_scif_offset, sh3_scif_size, sh4_scif_offset, sh4_scif_size, \
+ h8_sci_offset, h8_sci_size) \
+ CPU_SCIx_FNS(name, sh4_sci_offset, sh4_sci_size, sh4_scif_offset, sh4_scif_size)
+#define SCIF_FNS(name, sh3_scif_offset, sh3_scif_size, sh4_scif_offset, sh4_scif_size) \
+ CPU_SCIF_FNS(name, sh4_scif_offset, sh4_scif_size)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7300) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7705)
#define SCIF_FNS(name, scif_offset, scif_size) \
CPU_SCIF_FNS(name, scif_offset, scif_size)
#else
@@ -362,8 +385,8 @@
#endif
#if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
- defined(CONFIG_CPU_SUBTYPE_SH7705) || \
- defined(CONFIG_CPU_SUBTYPE_SH7710)
+ defined(CONFIG_CPU_SUBTYPE_SH7705)
+
SCIF_FNS(SCSMR, 0x00, 16)
SCIF_FNS(SCBRR, 0x04, 8)
SCIF_FNS(SCSCR, 0x08, 16)
@@ -385,7 +408,9 @@ SCIx_FNS(SCxTDR, 0x06, 8, 0x0c, 8, 0x06, 8, 0x0C, 8, 0x03, 8)
SCIx_FNS(SCxSR, 0x08, 8, 0x10, 8, 0x08, 16, 0x10, 16, 0x04, 8)
SCIx_FNS(SCxRDR, 0x0a, 8, 0x14, 8, 0x0A, 8, 0x14, 8, 0x05, 8)
SCIF_FNS(SCFCR, 0x0c, 8, 0x18, 16)
-#if defined(CONFIG_CPU_SUBTYPE_SH7760) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7760) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7785)
SCIF_FNS(SCFDR, 0x0e, 16, 0x1C, 16)
SCIF_FNS(SCTFDR, 0x0e, 16, 0x1C, 16)
SCIF_FNS(SCRFDR, 0x0e, 16, 0x20, 16)
@@ -471,13 +496,24 @@ static inline int sci_rxd_in(struct uart_port *port)
return ctrl_inb(SCPDR)&0x10 ? 1 : 0; /* SCIF */
return 1;
}
-#elif defined(CONFIG_CPU_SUBTYPE_SH7710)
+#elif defined(CONFIG_CPU_SUBTYPE_SH7710) || defined(CONFIG_CPU_SUBTYPE_SH7712)
static inline int sci_rxd_in(struct uart_port *port)
{
- if (port->mapbase == SCSPTR0)
- return ctrl_inw(SCSPTR0 + 0x10) & 0x01 ? 1 : 0;
- return 1;
+ return sci_in(port,SCxSR)&0x0010 ? 1 : 0;
+}
+static inline void set_sh771x_scif_pfc(struct uart_port *port)
+{
+ if (port->mapbase == 0xA4400000){
+ ctrl_outw(ctrl_inw(PACR)&0xffc0,PACR);
+ ctrl_outw(ctrl_inw(PBCR)&0x0fff,PBCR);
+ return;
+ }
+ if (port->mapbase == 0xA4410000){
+ ctrl_outw(ctrl_inw(PBCR)&0xf003,PBCR);
+ return;
+ }
}
+
#elif defined(CONFIG_CPU_SUBTYPE_SH7750) || \
defined(CONFIG_CPU_SUBTYPE_SH7751) || \
defined(CONFIG_CPU_SUBTYPE_SH4_202)
@@ -576,6 +612,23 @@ static inline int sci_rxd_in(struct uart_port *port)
return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */
return 1;
}
+#elif defined(CONFIG_CPU_SUBTYPE_SH7785)
+static inline int sci_rxd_in(struct uart_port *port)
+{
+ if (port->mapbase == 0xffea0000)
+ return ctrl_inw(SCSPTR0) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xffeb0000)
+ return ctrl_inw(SCSPTR1) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xffec0000)
+ return ctrl_inw(SCSPTR2) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xffed0000)
+ return ctrl_inw(SCSPTR3) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xffee0000)
+ return ctrl_inw(SCSPTR4) & 0x0001 ? 1 : 0; /* SCIF */
+ if (port->mapbase == 0xffef0000)
+ return ctrl_inw(SCSPTR5) & 0x0001 ? 1 : 0; /* SCIF */
+ return 1;
+}
#elif defined(CONFIG_CPU_SUBTYPE_SH7206)
static inline int sci_rxd_in(struct uart_port *port)
{
@@ -634,7 +687,9 @@ static inline int sci_rxd_in(struct uart_port *port)
* -- Mitch Davis - 15 Jul 2000
*/
-#if defined(CONFIG_CPU_SUBTYPE_SH7300) || defined(CONFIG_CPU_SUBTYPE_SH7780)
+#if defined(CONFIG_CPU_SUBTYPE_SH7300) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7780) || \
+ defined(CONFIG_CPU_SUBTYPE_SH7785)
#define SCBRR_VALUE(bps, clk) ((clk+16*bps)/(16*bps)-1)
#elif defined(CONFIG_CPU_SUBTYPE_SH7705)
#define SCBRR_VALUE(bps, clk) (((clk*2)+16*bps)/(32*bps)-1)
diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c
index 96a852aa190..2a63cdba320 100644
--- a/drivers/serial/sunsu.c
+++ b/drivers/serial/sunsu.c
@@ -1312,7 +1312,7 @@ static void sunsu_console_write(struct console *co, const char *s,
* - initialize the serial port
* Return non-zero if we didn't find a serial port.
*/
-static int sunsu_console_setup(struct console *co, char *options)
+static int __init sunsu_console_setup(struct console *co, char *options)
{
struct uart_port *port;
int baud = 9600;
@@ -1343,7 +1343,7 @@ static int sunsu_console_setup(struct console *co, char *options)
return uart_set_options(port, co, baud, parity, bits, flow);
}
-static struct console sunsu_cons = {
+static struct console sunsu_console = {
.name = "ttyS",
.write = sunsu_console_write,
.device = uart_console_device,
@@ -1373,9 +1373,9 @@ static inline struct console *SUNSU_CONSOLE(int num_uart)
if (i == num_uart)
return NULL;
- sunsu_cons.index = i;
+ sunsu_console.index = i;
- return &sunsu_cons;
+ return &sunsu_console;
}
#else
#define SUNSU_CONSOLE(num_uart) (NULL)
@@ -1387,8 +1387,8 @@ static enum su_type __devinit su_get_type(struct device_node *dp)
struct device_node *ap = of_find_node_by_path("/aliases");
if (ap) {
- char *keyb = of_get_property(ap, "keyboard", NULL);
- char *ms = of_get_property(ap, "mouse", NULL);
+ const char *keyb = of_get_property(ap, "keyboard", NULL);
+ const char *ms = of_get_property(ap, "mouse", NULL);
if (keyb) {
if (dp == of_find_node_by_path(keyb))
generated by cgit v1.2.3-70-g09d2 (git 2.46.0) at 2024-11-16 16:02:12 +0000