diff options
Diffstat (limited to 'drivers/serial')
43 files changed, 5030 insertions, 413 deletions
diff --git a/drivers/serial/21285.c b/drivers/serial/21285.c index 8681f134505..d89aa38c5cf 100644 --- a/drivers/serial/21285.c +++ b/drivers/serial/21285.c @@ -216,7 +216,7 @@ serial21285_set_termios(struct uart_port *port, struct ktermios *termios, struct ktermios *old) { unsigned long flags; - unsigned int baud, quot, h_lcr; + unsigned int baud, quot, h_lcr, b; /* * We don't support modem control lines. @@ -234,12 +234,8 @@ serial21285_set_termios(struct uart_port *port, struct ktermios *termios, */ baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); quot = uart_get_divisor(port, baud); - - if (port->state && port->state->port.tty) { - struct tty_struct *tty = port->state->port.tty; - unsigned int b = port->uartclk / (16 * quot); - tty_encode_baud_rate(tty, b, b); - } + b = port->uartclk / (16 * quot); + tty_termios_encode_baud_rate(termios, b, b); switch (termios->c_cflag & CSIZE) { case CS5: diff --git a/drivers/serial/68328serial.c b/drivers/serial/68328serial.c index 30463862603..7356a56ac45 100644 --- a/drivers/serial/68328serial.c +++ b/drivers/serial/68328serial.c @@ -78,10 +78,6 @@ struct m68k_serial *m68k_consinfo = 0; #define M68K_CLOCK (16667000) /* FIXME: 16MHz is likely wrong */ -#ifdef CONFIG_CONSOLE -extern wait_queue_head_t keypress_wait; -#endif - struct tty_driver *serial_driver; /* number of characters left in xmit buffer before we ask for more */ @@ -102,19 +98,13 @@ static void change_speed(struct m68k_serial *info); * Setup for console. Argument comes from the boot command line. */ -#if defined(CONFIG_M68EZ328ADS) || defined(CONFIG_ALMA_ANS) || defined(CONFIG_DRAGONIXVZ) -#define CONSOLE_BAUD_RATE 115200 -#define DEFAULT_CBAUD B115200 -#else - /* (es) */ - /* note: this is messy, but it works, again, perhaps defined somewhere else?*/ - #ifdef CONFIG_M68VZ328 - #define CONSOLE_BAUD_RATE 19200 - #define DEFAULT_CBAUD B19200 - #endif - /* (/es) */ +/* note: this is messy, but it works, again, perhaps defined somewhere else?*/ +#ifdef CONFIG_M68VZ328 +#define CONSOLE_BAUD_RATE 19200 +#define DEFAULT_CBAUD B19200 #endif + #ifndef CONSOLE_BAUD_RATE #define CONSOLE_BAUD_RATE 9600 #define DEFAULT_CBAUD B9600 @@ -300,10 +290,6 @@ static void receive_chars(struct m68k_serial *info, unsigned short rx) return; #endif /* CONFIG_MAGIC_SYSRQ */ } - /* It is a 'keyboard interrupt' ;-) */ -#ifdef CONFIG_CONSOLE - wake_up(&keypress_wait); -#endif } if(!tty) @@ -1243,7 +1229,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, retval = -ERESTARTSYS; break; } + tty_unlock(); schedule(); + tty_lock(); } current->state = TASK_RUNNING; remove_wait_queue(&info->open_wait, &wait); diff --git a/drivers/serial/68360serial.c b/drivers/serial/68360serial.c index 768612f8e41..0dff3bbddc8 100644 --- a/drivers/serial/68360serial.c +++ b/drivers/serial/68360serial.c @@ -1705,7 +1705,6 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout) printk("jiff=%lu...", jiffies); #endif - lock_kernel(); /* We go through the loop at least once because we can't tell * exactly when the last character exits the shifter. There can * be at least two characters waiting to be sent after the buffers @@ -1734,7 +1733,6 @@ static void rs_360_wait_until_sent(struct tty_struct *tty, int timeout) bdp--; } while (bdp->status & BD_SC_READY); current->state = TASK_RUNNING; - unlock_kernel(); #ifdef SERIAL_DEBUG_RS_WAIT_UNTIL_SENT printk("lsr = %d (jiff=%lu)...done\n", lsr, jiffies); #endif @@ -1862,7 +1860,9 @@ static int block_til_ready(struct tty_struct *tty, struct file * filp, printk("block_til_ready blocking: ttys%d, count = %d\n", info->line, state->count); #endif + tty_unlock(); schedule(); + tty_lock(); } current->state = TASK_RUNNING; remove_wait_queue(&info->open_wait, &wait); diff --git a/drivers/serial/8250.c b/drivers/serial/8250.c index 891e1dd65f2..24110f6f61e 100644 --- a/drivers/serial/8250.c +++ b/drivers/serial/8250.c @@ -241,7 +241,7 @@ static const struct serial8250_config uart_config[] = { .fifo_size = 128, .tx_loadsz = 128, .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, - .flags = UART_CAP_FIFO, + .flags = UART_CAP_FIFO | UART_CAP_EFR | UART_CAP_SLEEP, }, [PORT_16654] = { .name = "ST16654", @@ -300,9 +300,16 @@ static const struct serial8250_config uart_config[] = { .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_00, .flags = UART_CAP_FIFO | UART_CAP_AFE, }, + [PORT_U6_16550A] = { + .name = "U6_16550A", + .fifo_size = 64, + .tx_loadsz = 64, + .fcr = UART_FCR_ENABLE_FIFO | UART_FCR_R_TRIG_10, + .flags = UART_CAP_FIFO | UART_CAP_AFE, + }, }; -#if defined (CONFIG_SERIAL_8250_AU1X00) +#if defined(CONFIG_MIPS_ALCHEMY) /* Au1x00 UART hardware has a weird register layout */ static const u8 au_io_in_map[] = { @@ -422,7 +429,6 @@ static unsigned int mem32_serial_in(struct uart_port *p, int offset) return readl(p->membase + offset); } -#ifdef CONFIG_SERIAL_8250_AU1X00 static unsigned int au_serial_in(struct uart_port *p, int offset) { offset = map_8250_in_reg(p, offset) << p->regshift; @@ -434,7 +440,6 @@ static void au_serial_out(struct uart_port *p, int offset, int value) offset = map_8250_out_reg(p, offset) << p->regshift; __raw_writel(value, p->membase + offset); } -#endif static unsigned int tsi_serial_in(struct uart_port *p, int offset) { @@ -503,12 +508,11 @@ static void set_io_from_upio(struct uart_port *p) p->serial_out = mem32_serial_out; break; -#ifdef CONFIG_SERIAL_8250_AU1X00 case UPIO_AU: p->serial_in = au_serial_in; p->serial_out = au_serial_out; break; -#endif + case UPIO_TSI: p->serial_in = tsi_serial_in; p->serial_out = tsi_serial_out; @@ -535,9 +539,7 @@ serial_out_sync(struct uart_8250_port *up, int offset, int value) switch (p->iotype) { case UPIO_MEM: case UPIO_MEM32: -#ifdef CONFIG_SERIAL_8250_AU1X00 case UPIO_AU: -#endif case UPIO_DWAPB: p->serial_out(p, offset, value); p->serial_in(p, UART_LCR); /* safe, no side-effects */ @@ -573,7 +575,7 @@ static inline void _serial_dl_write(struct uart_8250_port *up, int value) serial_outp(up, UART_DLM, value >> 8 & 0xff); } -#if defined(CONFIG_SERIAL_8250_AU1X00) +#if defined(CONFIG_MIPS_ALCHEMY) /* Au1x00 haven't got a standard divisor latch */ static int serial_dl_read(struct uart_8250_port *up) { @@ -1075,6 +1077,15 @@ static void autoconfig_16550a(struct uart_8250_port *up) DEBUG_AUTOCONF("Couldn't force IER_UUE to 0 "); } serial_outp(up, UART_IER, iersave); + + /* + * We distinguish between 16550A and U6 16550A by counting + * how many bytes are in the FIFO. + */ + if (up->port.type == PORT_16550A && size_fifo(up) == 64) { + up->port.type = PORT_U6_16550A; + up->capabilities |= UART_CAP_AFE; + } } /* @@ -2229,9 +2240,9 @@ static unsigned int serial8250_get_divisor(struct uart_port *port, unsigned int return quot; } -static void -serial8250_set_termios(struct uart_port *port, struct ktermios *termios, - struct ktermios *old) +void +serial8250_do_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) { struct uart_8250_port *up = (struct uart_8250_port *)port; unsigned char cval, fcr = 0; @@ -2407,16 +2418,22 @@ serial8250_set_termios(struct uart_port *port, struct ktermios *termios, if (tty_termios_baud_rate(termios)) tty_termios_encode_baud_rate(termios, baud, baud); } +EXPORT_SYMBOL(serial8250_do_set_termios); static void -serial8250_set_ldisc(struct uart_port *port) +serial8250_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) { - int line = port->line; - - if (line >= port->state->port.tty->driver->num) - return; + if (port->set_termios) + port->set_termios(port, termios, old); + else + serial8250_do_set_termios(port, termios, old); +} - if (port->state->port.tty->ldisc->ops->num == N_PPS) { +static void +serial8250_set_ldisc(struct uart_port *port, int new) +{ + if (new == N_PPS) { port->flags |= UPF_HARDPPS_CD; serial8250_enable_ms(port); } else @@ -2596,11 +2613,9 @@ static void serial8250_config_port(struct uart_port *port, int flags) if (flags & UART_CONFIG_TYPE) autoconfig(up, probeflags); -#ifdef CONFIG_SERIAL_8250_AU1X00 /* if access method is AU, it is a 16550 with a quirk */ if (up->port.type == PORT_16550A && up->port.iotype == UPIO_AU) up->bugs |= UART_BUG_NOMSR; -#endif if (up->port.type != PORT_UNKNOWN && flags & UART_CONFIG_IRQ) autoconfig_irq(up); @@ -2994,6 +3009,7 @@ static int __devinit serial8250_probe(struct platform_device *dev) port.type = p->type; port.serial_in = p->serial_in; port.serial_out = p->serial_out; + port.set_termios = p->set_termios; port.dev = &dev->dev; port.irqflags |= irqflag; ret = serial8250_register_port(&port); @@ -3157,6 +3173,9 @@ int serial8250_register_port(struct uart_port *port) uart->port.serial_in = port->serial_in; if (port->serial_out) uart->port.serial_out = port->serial_out; + /* Possibly override set_termios call */ + if (port->set_termios) + uart->port.set_termios = port->set_termios; ret = uart_add_one_port(&serial8250_reg, &uart->port); if (ret == 0) diff --git a/drivers/serial/8250_early.c b/drivers/serial/8250_early.c index f279745e9fe..b745792ec25 100644 --- a/drivers/serial/8250_early.c +++ b/drivers/serial/8250_early.c @@ -19,9 +19,11 @@ * The user can specify the device directly, e.g., * earlycon=uart8250,io,0x3f8,9600n8 * earlycon=uart8250,mmio,0xff5e0000,115200n8 + * earlycon=uart8250,mmio32,0xff5e0000,115200n8 * or * console=uart8250,io,0x3f8,9600n8 * console=uart8250,mmio,0xff5e0000,115200n8 + * console=uart8250,mmio32,0xff5e0000,115200n8 */ #include <linux/tty.h> @@ -48,18 +50,31 @@ static struct early_serial8250_device early_device; static unsigned int __init serial_in(struct uart_port *port, int offset) { - if (port->iotype == UPIO_MEM) + switch (port->iotype) { + case UPIO_MEM: return readb(port->membase + offset); - else + case UPIO_MEM32: + return readl(port->membase + (offset << 2)); + case UPIO_PORT: return inb(port->iobase + offset); + default: + return 0; + } } static void __init serial_out(struct uart_port *port, int offset, int value) { - if (port->iotype == UPIO_MEM) + switch (port->iotype) { + case UPIO_MEM: writeb(value, port->membase + offset); - else + break; + case UPIO_MEM32: + writel(value, port->membase + (offset << 2)); + break; + case UPIO_PORT: outb(value, port->iobase + offset); + break; + } } #define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) @@ -137,15 +152,21 @@ static int __init parse_options(struct early_serial8250_device *device, char *options) { struct uart_port *port = &device->port; - int mmio, length; + int mmio, mmio32, length; if (!options) return -ENODEV; port->uartclk = BASE_BAUD * 16; - if (!strncmp(options, "mmio,", 5)) { - port->iotype = UPIO_MEM; - port->mapbase = simple_strtoul(options + 5, &options, 0); + + mmio = !strncmp(options, "mmio,", 5); + mmio32 = !strncmp(options, "mmio32,", 7); + if (mmio || mmio32) { + port->iotype = (mmio ? UPIO_MEM : UPIO_MEM32); + port->mapbase = simple_strtoul(options + (mmio ? 5 : 7), + &options, 0); + if (mmio32) + port->regshift = 2; #ifdef CONFIG_FIX_EARLYCON_MEM set_fixmap_nocache(FIX_EARLYCON_MEM_BASE, port->mapbase & PAGE_MASK); @@ -157,11 +178,10 @@ static int __init parse_options(struct early_serial8250_device *device, if (!port->membase) { printk(KERN_ERR "%s: Couldn't ioremap 0x%llx\n", __func__, - (unsigned long long)port->mapbase); + (unsigned long long) port->mapbase); return -ENOMEM; } #endif - mmio = 1; } else if (!strncmp(options, "io,", 3)) { port->iotype = UPIO_PORT; port->iobase = simple_strtoul(options + 3, &options, 0); @@ -181,11 +201,18 @@ static int __init parse_options(struct early_serial8250_device *device, device->baud); } - printk(KERN_INFO "Early serial console at %s 0x%llx (options '%s')\n", - mmio ? "MMIO" : "I/O port", - mmio ? (unsigned long long) port->mapbase - : (unsigned long long) port->iobase, - device->options); + if (mmio || mmio32) + printk(KERN_INFO + "Early serial console at MMIO%s 0x%llu (options '%s')\n", + mmio32 ? "32" : "", + (unsigned long long)port->mapbase, + device->options); + else + printk(KERN_INFO + "Early serial console at I/O port 0x%lu (options '%s')\n", + port->iobase, + device->options); + return 0; } diff --git a/drivers/serial/8250_pci.c b/drivers/serial/8250_pci.c index 746a44621d9..53be4d35a0a 100644 --- a/drivers/serial/8250_pci.c +++ b/drivers/serial/8250_pci.c @@ -994,6 +994,7 @@ static int skip_tx_en_setup(struct serial_private *priv, #define PCI_DEVICE_ID_TITAN_800E 0xA014 #define PCI_DEVICE_ID_TITAN_200EI 0xA016 #define PCI_DEVICE_ID_TITAN_200EISI 0xA017 +#define PCI_DEVICE_ID_OXSEMI_16PCI958 0x9538 /* Unknown vendors/cards - this should not be in linux/pci_ids.h */ #define PCI_SUBDEVICE_ID_UNKNOWN_0x1584 0x1584 @@ -1542,6 +1543,8 @@ enum pci_board_num_t { pbn_b2_4_921600, pbn_b2_8_921600, + pbn_b2_8_1152000, + pbn_b2_bt_1_115200, pbn_b2_bt_2_115200, pbn_b2_bt_4_115200, @@ -1960,6 +1963,13 @@ static struct pciserial_board pci_boards[] __devinitdata = { .uart_offset = 8, }, + [pbn_b2_8_1152000] = { + .flags = FL_BASE2, + .num_ports = 8, + .base_baud = 1152000, + .uart_offset = 8, + }, + [pbn_b2_bt_1_115200] = { .flags = FL_BASE2|FL_BASE_BARS, .num_ports = 1, @@ -2875,6 +2885,9 @@ static struct pci_device_id serial_pci_tbl[] = { { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b0_bt_2_921600 }, + { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI958, + PCI_ANY_ID , PCI_ANY_ID, 0, 0, + pbn_b2_8_1152000 }, /* * Oxford Semiconductor Inc. Tornado PCI express device range. diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 8b23165bc5d..12900f7083b 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -258,14 +258,6 @@ config SERIAL_8250_ACORN system, say Y to this option. The driver can handle 1, 2, or 3 port cards. If unsure, say N. -config SERIAL_8250_AU1X00 - bool "Au1x00 serial port support" - depends on SERIAL_8250 != n && SOC_AU1X00 - help - If you have an Au1x00 SOC based board and want to use the serial port, - say Y to this option. The driver can handle up to 4 serial ports, - depending on the SOC. If unsure, say N. - config SERIAL_8250_RM9K bool "Support for MIPS RM9xxx integrated serial port" depends on SERIAL_8250 != n && SERIAL_RM9000 @@ -544,12 +536,13 @@ config SERIAL_S3C6400 config SERIAL_S5PV210 tristate "Samsung S5PV210 Serial port support" - depends on SERIAL_SAMSUNG && (CPU_S5PV210 || CPU_S5P6442) - select SERIAL_SAMSUNG_UARTS_4 if CPU_S5PV210 + depends on SERIAL_SAMSUNG && (CPU_S5PV210 || CPU_S5P6442 || CPU_S5PV310) + select SERIAL_SAMSUNG_UARTS_4 if (CPU_S5PV210 || CPU_S5PV310) default y help Serial port support for Samsung's S5P Family of SoC's + config SERIAL_MAX3100 tristate "MAX3100 support" depends on SPI @@ -557,6 +550,22 @@ config SERIAL_MAX3100 help MAX3100 chip support +config SERIAL_MAX3107 + tristate "MAX3107 support" + depends on SPI + select SERIAL_CORE + help + MAX3107 chip support + +config SERIAL_MAX3107_AAVA + tristate "MAX3107 AAVA platform support" + depends on X86_MRST && SERIAL_MAX3107 && GPIOLIB + select SERIAL_CORE + help + Support for the MAX3107 chip configuration found on the AAVA + platform. Includes the extra initialisation and GPIO support + neded for this device. + config SERIAL_DZ bool "DECstation DZ serial driver" depends on MACH_DECSTATION && 32BIT @@ -698,6 +707,33 @@ config SERIAL_SA1100_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) +config SERIAL_MRST_MAX3110 + tristate "SPI UART driver for Max3110" + depends on SPI_DW_PCI + select SERIAL_CORE + select SERIAL_CORE_CONSOLE + help + This is the UART protocol driver for the MAX3110 device on + the Intel Moorestown platform. On other systems use the max3100 + driver. + +config MRST_MAX3110_IRQ + boolean "Enable GPIO IRQ for Max3110 over Moorestown" + default n + depends on SERIAL_MRST_MAX3110 && GPIO_LANGWELL + help + This has to be enabled after Moorestown GPIO driver is loaded + +config SERIAL_MFD_HSU + tristate "Medfield High Speed UART support" + depends on PCI + select SERIAL_CORE + +config SERIAL_MFD_HSU_CONSOLE + boolean "Medfile HSU serial console support" + depends on SERIAL_MFD_HSU=y + select SERIAL_CORE_CONSOLE + config SERIAL_BFIN tristate "Blackfin serial port support" depends on BLACKFIN diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 208a85572c3..1ca4fd599ff 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -46,6 +46,8 @@ obj-$(CONFIG_SERIAL_S3C24A0) += s3c24a0.o obj-$(CONFIG_SERIAL_S3C6400) += s3c6400.o obj-$(CONFIG_SERIAL_S5PV210) += s5pv210.o obj-$(CONFIG_SERIAL_MAX3100) += max3100.o +obj-$(CONFIG_SERIAL_MAX3107) += max3107.o +obj-$(CONFIG_SERIAL_MAX3107_AAVA) += max3107-aava.o obj-$(CONFIG_SERIAL_IP22_ZILOG) += ip22zilog.o obj-$(CONFIG_SERIAL_MUX) += mux.o obj-$(CONFIG_SERIAL_68328) += 68328serial.o @@ -84,3 +86,5 @@ obj-$(CONFIG_SERIAL_TIMBERDALE) += timbuart.o obj-$(CONFIG_SERIAL_GRLIB_GAISLER_APBUART) += apbuart.o obj-$(CONFIG_SERIAL_ALTERA_JTAGUART) += altera_jtaguart.o obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o +obj-$(CONFIG_SERIAL_MRST_MAX3110) += mrst_max3110.o +obj-$(CONFIG_SERIAL_MFD_HSU) += mfd.o diff --git a/drivers/serial/altera_uart.c b/drivers/serial/altera_uart.c index 0f1189605d2..f8d8a00554d 100644 --- a/drivers/serial/altera_uart.c +++ b/drivers/serial/altera_uart.c @@ -394,7 +394,7 @@ int __init early_altera_uart_setup(struct altera_uart_platform_uart *platp) static void altera_uart_console_putc(struct uart_port *port, const char c) { while (!(readl(port->membase + ALTERA_UART_STATUS_REG) & - ALTERA_UART_STATUS_TRDY_MSK)) + ALTERA_UART_STATUS_TRDY_MSK)) cpu_relax(); writel(c, port->membase + ALTERA_UART_TXDATA_REG); diff --git a/drivers/serial/apbuart.c b/drivers/serial/apbuart.c index 0099b8692b6..cc01c650a14 100644 --- a/drivers/serial/apbuart.c +++ b/drivers/serial/apbuart.c @@ -551,7 +551,7 @@ static struct uart_driver grlib_apbuart_driver = { /* OF Platform Driver */ /* ======================================================================== */ -static int __devinit apbuart_probe(struct of_device *op, +static int __devinit apbuart_probe(struct platform_device *op, const struct of_device_id *match) { int i = -1; diff --git a/drivers/serial/atmel_serial.c b/drivers/serial/atmel_serial.c index a182def7007..3892666b5fb 100644 --- a/drivers/serial/atmel_serial.c +++ b/drivers/serial/atmel_serial.c @@ -217,7 +217,8 @@ void atmel_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf) if (rs485conf->flags & SER_RS485_ENABLED) { dev_dbg(port->dev, "Setting UART to RS485\n"); atmel_port->tx_done_mask = ATMEL_US_TXEMPTY; - UART_PUT_TTGR(port, rs485conf->delay_rts_before_send); + if (rs485conf->flags & SER_RS485_RTS_AFTER_SEND) + UART_PUT_TTGR(port, rs485conf->delay_rts_after_send); mode |= ATMEL_US_USMODE_RS485; } else { dev_dbg(port->dev, "Setting UART to RS232\n"); @@ -292,7 +293,9 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) if (atmel_port->rs485.flags & SER_RS485_ENABLED) { dev_dbg(port->dev, "Setting UART to RS485\n"); - UART_PUT_TTGR(port, atmel_port->rs485.delay_rts_before_send); + if (atmel_port->rs485.flags & SER_RS485_RTS_AFTER_SEND) + UART_PUT_TTGR(port, + atmel_port->rs485.delay_rts_after_send); mode |= ATMEL_US_USMODE_RS485; } else { dev_dbg(port->dev, "Setting UART to RS232\n"); @@ -1211,7 +1214,9 @@ static void atmel_set_termios(struct uart_port *port, struct ktermios *termios, if (atmel_port->rs485.flags & SER_RS485_ENABLED) { dev_dbg(port->dev, "Setting UART to RS485\n"); - UART_PUT_TTGR(port, atmel_port->rs485.delay_rts_before_send); + if (atmel_port->rs485.flags & SER_RS485_RTS_AFTER_SEND) + UART_PUT_TTGR(port, + atmel_port->rs485.delay_rts_after_send); mode |= ATMEL_US_USMODE_RS485; } else { dev_dbg(port->dev, "Setting UART to RS232\n"); diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c index 511cbf68787..a9eff2b18ea 100644 --- a/drivers/serial/bfin_5xx.c +++ b/drivers/serial/bfin_5xx.c @@ -957,15 +957,12 @@ bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser) * Enable the IrDA function if tty->ldisc.num is N_IRDA. * In other cases, disable IrDA function. */ -static void bfin_serial_set_ldisc(struct uart_port *port) +static void bfin_serial_set_ldisc(struct uart_port *port, int ld) { int line = port->line; unsigned short val; - if (line >= port->state->port.tty->driver->num) - return; - - switch (port->state->port.tty->termios->c_line) { + switch (ld) { case N_IRDA: val = UART_GET_GCTL(&bfin_serial_ports[line]); val |= (IREN | RPOLC); diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index 6016179db53..f2b8adcc6c9 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -1340,7 +1340,7 @@ static struct uart_driver cpm_reg = { static int probe_index; -static int __devinit cpm_uart_probe(struct of_device *ofdev, +static int __devinit cpm_uart_probe(struct platform_device *ofdev, const struct of_device_id *match) { int index = probe_index++; @@ -1364,7 +1364,7 @@ static int __devinit cpm_uart_probe(struct of_device *ofdev, return uart_add_one_port(&cpm_reg, &pinfo->port); } -static int __devexit cpm_uart_remove(struct of_device *ofdev) +static int __devexit cpm_uart_remove(struct platform_device *ofdev) { struct uart_cpm_port *pinfo = dev_get_drvdata(&ofdev->dev); return uart_remove_one_port(&cpm_reg, &pinfo->port); diff --git a/drivers/serial/crisv10.c b/drivers/serial/crisv10.c index 31f172397af..c856905bb3b 100644 --- a/drivers/serial/crisv10.c +++ b/drivers/serial/crisv10.c @@ -3724,6 +3724,17 @@ rs_ioctl(struct tty_struct *tty, struct file * file, return e100_enable_rs485(tty, &rs485data); } + case TIOCGRS485: + { + struct serial_rs485 *rs485data = + &(((struct e100_serial *)tty->driver_data)->rs485); + /* This is the ioctl to get RS485 data from user-space */ + if (copy_to_user((struct serial_rs485 *) arg, + rs485data, + sizeof(serial_rs485))) + return -EFAULT; + break; + } case TIOCSERWRRS485: { @@ -3924,7 +3935,6 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout) * Check R_DMA_CHx_STATUS bit 0-6=number of available bytes in FIFO * R_DMA_CHx_HWSW bit 31-16=nbr of bytes left in DMA buffer (0=64k) */ - lock_kernel(); orig_jiffies = jiffies; while (info->xmit.head != info->xmit.tail || /* More in send queue */ (*info->ostatusadr & 0x007f) || /* more in FIFO */ @@ -3941,7 +3951,6 @@ static void rs_wait_until_sent(struct tty_struct *tty, int timeout) curr_time_usec - info->last_tx_active_usec; } set_current_state(TASK_RUNNING); - unlock_kernel(); } /* @@ -3981,7 +3990,7 @@ block_til_ready(struct tty_struct *tty, struct file * filp, */ if (tty_hung_up_p(filp) || (info->flags & ASYNC_CLOSING)) { - wait_event_interruptible(info->close_wait, + wait_event_interruptible_tty(info->close_wait, !(info->flags & ASYNC_CLOSING)); #ifdef SERIAL_DO_RESTART if (info->flags & ASYNC_HUP_NOTIFY) @@ -4057,7 +4066,9 @@ block_til_ready(struct tty_struct *tty, struct file * filp, printk("block_til_ready blocking: ttyS%d, count = %d\n", info->line, info->count); #endif + tty_unlock(); schedule(); + tty_lock(); } set_current_state(TASK_RUNNING); remove_wait_queue(&info->open_wait, &wait); @@ -4139,7 +4150,7 @@ rs_open(struct tty_struct *tty, struct file * filp) */ if (tty_hung_up_p(filp) || (info->flags & ASYNC_CLOSING)) { - wait_event_interruptible(info->close_wait, + wait_event_interruptible_tty(info->close_wait, !(info->flags & ASYNC_CLOSING)); #ifdef SERIAL_DO_RESTART return ((info->flags & ASYNC_HUP_NOTIFY) ? @@ -4522,8 +4533,8 @@ static int __init rs_init(void) INIT_WORK(&info->work, do_softint); if (info->enabled) { - printk(KERN_INFO "%s%d at 0x%x is a builtin UART with DMA\n", - serial_driver->name, info->line, (unsigned int)info->ioport); + printk(KERN_INFO "%s%d at %p is a builtin UART with DMA\n", + serial_driver->name, info->line, info->ioport); } } #ifdef CONFIG_ETRAX_FAST_TIMER diff --git a/drivers/serial/imx.c b/drivers/serial/imx.c index eacb588a934..66ecc7ab6da 100644 --- a/drivers/serial/imx.c +++ b/drivers/serial/imx.c @@ -909,13 +909,11 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios, rational_best_approximation(16 * div * baud, sport->port.uartclk, 1 << 16, 1 << 16, &num, &denom); - if (port->state && port->state->port.tty) { - tdiv64 = sport->port.uartclk; - tdiv64 *= num; - do_div(tdiv64, denom * 16 * div); - tty_encode_baud_rate(sport->port.state->port.tty, + tdiv64 = sport->port.uartclk; + tdiv64 *= num; + do_div(tdiv64, denom * 16 * div); + tty_termios_encode_baud_rate(termios, (speed_t)tdiv64, (speed_t)tdiv64); - } num -= 1; denom -= 1; diff --git a/drivers/serial/ioc3_serial.c b/drivers/serial/ioc3_serial.c index f164ba4eba0..93de907b120 100644 --- a/drivers/serial/ioc3_serial.c +++ b/drivers/serial/ioc3_serial.c @@ -954,12 +954,13 @@ ioc3_change_speed(struct uart_port *the_port, struct ktermios *new_termios, struct ktermios *old_termios) { struct ioc3_port *port = get_ioc3_port(the_port); - unsigned int cflag; + unsigned int cflag, iflag; int baud; int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8; struct uart_state *state = the_port->state; cflag = new_termios->c_cflag; + iflag = new_termios->c_iflag; switch (cflag & CSIZE) { case CS5: @@ -1000,12 +1001,12 @@ ioc3_change_speed(struct uart_port *the_port, state->port.tty->low_latency = 1; - if (I_IGNPAR(state->port.tty)) + if (iflag & IGNPAR) the_port->ignore_status_mask &= ~(N_PARITY_ERROR | N_FRAMING_ERROR); - if (I_IGNBRK(state->port.tty)) { + if (iflag & IGNBRK) { the_port->ignore_status_mask &= ~N_BREAK; - if (I_IGNPAR(state->port.tty)) + if (iflag & IGNPAR) the_port->ignore_status_mask &= ~N_OVERRUN_ERROR; } if (!(cflag & CREAD)) { diff --git a/drivers/serial/ioc4_serial.c b/drivers/serial/ioc4_serial.c index 8ad28fc6492..fcfe82653ac 100644 --- a/drivers/serial/ioc4_serial.c +++ b/drivers/serial/ioc4_serial.c @@ -1685,11 +1685,12 @@ ioc4_change_speed(struct uart_port *the_port, { struct ioc4_port *port = get_ioc4_port(the_port, 0); int baud, bits; - unsigned cflag; + unsigned cflag, iflag; int new_parity = 0, new_parity_enable = 0, new_stop = 0, new_data = 8; struct uart_state *state = the_port->state; cflag = new_termios->c_cflag; + iflag = new_termios->c_iflag; switch (cflag & CSIZE) { case CS5: @@ -1741,12 +1742,12 @@ ioc4_change_speed(struct uart_port *the_port, state->port.tty->low_latency = 1; - if (I_IGNPAR(state->port.tty)) + if (iflag & IGNPAR) the_port->ignore_status_mask &= ~(N_PARITY_ERROR | N_FRAMING_ERROR); - if (I_IGNBRK(state->port.tty)) { + if (iflag & IGNBRK) { the_port->ignore_status_mask &= ~N_BREAK; - if (I_IGNPAR(state->port.tty)) + if (iflag & IGNPAR) the_port->ignore_status_mask &= ~N_OVERRUN_ERROR; } if (!(cflag & CREAD)) { diff --git a/drivers/serial/kgdboc.c b/drivers/serial/kgdboc.c index a9a94ae7234..39f9a1adaa7 100644 --- a/drivers/serial/kgdboc.c +++ b/drivers/serial/kgdboc.c @@ -17,6 +17,7 @@ #include <linux/kdb.h> #include <linux/tty.h> #include <linux/console.h> +#include <linux/vt_kern.h> #define MAX_CONFIG_LEN 40 @@ -31,6 +32,7 @@ static struct kparam_string kps = { .maxlen = MAX_CONFIG_LEN, }; +static int kgdboc_use_kms; /* 1 if we use kernel mode switching */ static struct tty_driver *kgdb_tty_driver; static int kgdb_tty_line; @@ -104,6 +106,12 @@ static int configure_kgdboc(void) kgdboc_io_ops.is_console = 0; kgdb_tty_driver = NULL; + kgdboc_use_kms = 0; + if (strncmp(cptr, "kms,", 4) == 0) { + cptr += 4; + kgdboc_use_kms = 1; + } + if (kgdboc_register_kbd(&cptr)) goto do_register; @@ -201,8 +209,14 @@ static int param_set_kgdboc_var(const char *kmessage, struct kernel_param *kp) return configure_kgdboc(); } +static int dbg_restore_graphics; + static void kgdboc_pre_exp_handler(void) { + if (!dbg_restore_graphics && kgdboc_use_kms) { + dbg_restore_graphics = 1; + con_debug_enter(vc_cons[fg_console].d); + } /* Increment the module count when the debugger is active */ if (!kgdb_connected) try_module_get(THIS_MODULE); @@ -213,6 +227,10 @@ static void kgdboc_post_exp_handler(void) /* decrement the module count when the debugger detaches */ if (!kgdb_connected) module_put(THIS_MODULE); + if (kgdboc_use_kms && dbg_restore_graphics) { + dbg_restore_graphics = 0; + con_debug_leave(); + } } static struct kgdb_io kgdboc_io_ops = { diff --git a/drivers/serial/max3100.c b/drivers/serial/max3100.c index 3351c3bd59e..beb1afa27d8 100644 --- a/drivers/serial/max3100.c +++ b/drivers/serial/max3100.c @@ -430,17 +430,14 @@ max3100_set_termios(struct uart_port *port, struct ktermios *termios, int baud = 0; unsigned cflag; u32 param_new, param_mask, parity = 0; - struct tty_struct *tty = s->port.state->port.tty; dev_dbg(&s->spi->dev, "%s\n", __func__); - if (!tty) - return; cflag = termios->c_cflag; param_new = 0; param_mask = 0; - baud = tty_get_baud_rate(tty); + baud = tty_termios_baud_rate(termios); param_new = s->conf & MAX3100_BAUD; switch (baud) { case 300: @@ -485,7 +482,7 @@ max3100_set_termios(struct uart_port *port, struct ktermios *termios, default: baud = s->baud; } - tty_encode_baud_rate(tty, baud, baud); + tty_termios_encode_baud_rate(termios, baud, baud); s->baud = baud; param_mask |= MAX3100_BAUD; diff --git a/drivers/serial/max3107-aava.c b/drivers/serial/max3107-aava.c new file mode 100644 index 00000000000..a1fe304f2f5 --- /dev/null +++ b/drivers/serial/max3107-aava.c @@ -0,0 +1,344 @@ +/* + * max3107.c - spi uart protocol driver for Maxim 3107 + * Based on max3100.c + * by Christian Pellegrin <chripell@evolware.org> + * and max3110.c + * by Feng Tang <feng.tang@intel.com> + * + * Copyright (C) Aavamobile 2009 + * + * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + * + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/spi/spi.h> +#include <linux/freezer.h> +#include <linux/platform_device.h> +#include <linux/gpio.h> +#include <linux/sfi.h> +#include <asm/mrst.h> +#include "max3107.h" + +/* GPIO direction to input function */ +static int max3107_gpio_direction_in(struct gpio_chip *chip, unsigned offset) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[1]; /* Buffer for SPI transfer */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return -EINVAL; + } + + /* Read current GPIO configuration register */ + buf[0] = MAX3107_GPIOCFG_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { + dev_err(&s->spi->dev, "SPI transfer GPIO read failed\n"); + return -EIO; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + + /* Set GPIO to input */ + buf[0] &= ~(0x0001 << offset); + + /* Write new GPIO configuration register value */ + buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIOCFG_REG); + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 2)) { + dev_err(&s->spi->dev, "SPI transfer GPIO write failed\n"); + return -EIO; + } + return 0; +} + +/* GPIO direction to output function */ +static int max3107_gpio_direction_out(struct gpio_chip *chip, unsigned offset, + int value) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[2]; /* Buffer for SPI transfers */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return -EINVAL; + } + + /* Read current GPIO configuration and data registers */ + buf[0] = MAX3107_GPIOCFG_REG; + buf[1] = MAX3107_GPIODATA_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 4)) { + dev_err(&s->spi->dev, "SPI transfer gpio failed\n"); + return -EIO; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + buf[1] &= MAX3107_SPI_RX_DATA_MASK; + + /* Set GPIO to output */ + buf[0] |= (0x0001 << offset); + /* Set value */ + if (value) + buf[1] |= (0x0001 << offset); + else + buf[1] &= ~(0x0001 << offset); + + /* Write new GPIO configuration and data register values */ + buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIOCFG_REG); + buf[1] |= (MAX3107_WRITE_BIT | MAX3107_GPIODATA_REG); + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 4)) { + dev_err(&s->spi->dev, + "SPI transfer for GPIO conf data w failed\n"); + return -EIO; + } + return 0; +} + +/* GPIO value query function */ +static int max3107_gpio_get(struct gpio_chip *chip, unsigned offset) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[1]; /* Buffer for SPI transfer */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return -EINVAL; + } + + /* Read current GPIO data register */ + buf[0] = MAX3107_GPIODATA_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { + dev_err(&s->spi->dev, "SPI transfer GPIO data r failed\n"); + return -EIO; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + + /* Return value */ + return buf[0] & (0x0001 << offset); +} + +/* GPIO value set function */ +static void max3107_gpio_set(struct gpio_chip *chip, unsigned offset, int value) +{ + struct max3107_port *s = container_of(chip, struct max3107_port, chip); + u16 buf[2]; /* Buffer for SPI transfers */ + + if (offset >= MAX3107_GPIO_COUNT) { + dev_err(&s->spi->dev, "Invalid GPIO\n"); + return; + } + + /* Read current GPIO configuration registers*/ + buf[0] = MAX3107_GPIODATA_REG; + buf[1] = MAX3107_GPIOCFG_REG; + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 4)) { + dev_err(&s->spi->dev, + "SPI transfer for GPIO data and config read failed\n"); + return; + } + buf[0] &= MAX3107_SPI_RX_DATA_MASK; + buf[1] &= MAX3107_SPI_RX_DATA_MASK; + + if (!(buf[1] & (0x0001 << offset))) { + /* Configured as input, can't set value */ + dev_warn(&s->spi->dev, + "Trying to set value for input GPIO\n"); + return; + } + + /* Set value */ + if (value) + buf[0] |= (0x0001 << offset); + else + buf[0] &= ~(0x0001 << offset); + + /* Write new GPIO data register value */ + buf[0] |= (MAX3107_WRITE_BIT | MAX3107_GPIODATA_REG); + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 2)) + dev_err(&s->spi->dev, "SPI transfer GPIO data w failed\n"); +} + +/* GPIO chip data */ +static struct gpio_chip max3107_gpio_chip = { + .owner = THIS_MODULE, + .direction_input = max3107_gpio_direction_in, + .direction_output = max3107_gpio_direction_out, + .get = max3107_gpio_get, + .set = max3107_gpio_set, + .can_sleep = 1, + .base = MAX3107_GPIO_BASE, + .ngpio = MAX3107_GPIO_COUNT, +}; + +/** + * max3107_aava_reset - reset on AAVA systems + * @spi: The SPI device we are probing + * + * Reset the device ready for probing. + */ + +static int max3107_aava_reset(struct spi_device *spi) +{ + /* Reset the chip */ + if (gpio_request(MAX3107_RESET_GPIO, "max3107")) { + pr_err("Requesting RESET GPIO failed\n"); + return -EIO; + } + if (gpio_direction_output(MAX3107_RESET_GPIO, 0)) { + pr_err("Setting RESET GPIO to 0 failed\n"); + gpio_free(MAX3107_RESET_GPIO); + return -EIO; + } + msleep(MAX3107_RESET_DELAY); + if (gpio_direction_output(MAX3107_RESET_GPIO, 1)) { + pr_err("Setting RESET GPIO to 1 failed\n"); + gpio_free(MAX3107_RESET_GPIO); + return -EIO; + } + gpio_free(MAX3107_RESET_GPIO); + msleep(MAX3107_WAKEUP_DELAY); + return 0; +} + +static int max3107_aava_configure(struct max3107_port *s) +{ + int retval; + + /* Initialize GPIO chip data */ + s->chip = max3107_gpio_chip; + s->chip.label = s->spi->modalias; + s->chip.dev = &s->spi->dev; + + /* Add GPIO chip */ + retval = gpiochip_add(&s->chip); + if (retval) { + dev_err(&s->spi->dev, "Adding GPIO chip failed\n"); + return retval; + } + + /* Temporary fix for EV2 boot problems, set modem reset to 0 */ + max3107_gpio_direction_out(&s->chip, 3, 0); + return 0; +} + +#if 0 +/* This will get enabled once we have the board stuff merged for this + specific case */ + +static const struct baud_table brg13_ext[] = { + { 300, MAX3107_BRG13_B300 }, + { 600, MAX3107_BRG13_B600 }, + { 1200, MAX3107_BRG13_B1200 }, + { 2400, MAX3107_BRG13_B2400 }, + { 4800, MAX3107_BRG13_B4800 }, + { 9600, MAX3107_BRG13_B9600 }, + { 19200, MAX3107_BRG13_B19200 }, + { 57600, MAX3107_BRG13_B57600 }, + { 115200, MAX3107_BRG13_B115200 }, + { 230400, MAX3107_BRG13_B230400 }, + { 460800, MAX3107_BRG13_B460800 }, + { 921600, MAX3107_BRG13_B921600 }, + { 0, 0 } +}; + +static void max3107_aava_init(struct max3107_port *s) +{ + /*override for AAVA SC specific*/ + if (mrst_platform_id() == MRST_PLATFORM_AAVA_SC) { + if (get_koski_build_id() <= KOSKI_EV2) + if (s->ext_clk) { + s->brg_cfg = MAX3107_BRG13_B9600; + s->baud_tbl = (struct baud_table *)brg13_ext; + } + } +} +#endif + +static int __devexit max3107_aava_remove(struct spi_device *spi) +{ + struct max3107_port *s = dev_get_drvdata(&spi->dev); + + /* Remove GPIO chip */ + if (gpiochip_remove(&s->chip)) + dev_warn(&spi->dev, "Removing GPIO chip failed\n"); + + /* Then do the default remove */ + return max3107_remove(spi); +} + +/* Platform data */ +static struct max3107_plat aava_plat_data = { + .loopback = 0, + .ext_clk = 1, +/* .init = max3107_aava_init, */ + .configure = max3107_aava_configure, + .hw_suspend = max3107_hw_susp, + .polled_mode = 0, + .poll_time = 0, +}; + + +static int __devinit max3107_probe_aava(struct spi_device *spi) +{ + int err = max3107_aava_reset(spi); + if (err < 0) + return err; + return max3107_probe(spi, &aava_plat_data); +} + +/* Spi driver data */ +static struct spi_driver max3107_driver = { + .driver = { + .name = "aava-max3107", + .bus = &spi_bus_type, + .owner = THIS_MODULE, + }, + .probe = max3107_probe_aava, + .remove = __devexit_p(max3107_aava_remove), + .suspend = max3107_suspend, + .resume = max3107_resume, +}; + +/* Driver init function */ +static int __init max3107_init(void) +{ + return spi_register_driver(&max3107_driver); +} + +/* Driver exit function */ +static void __exit max3107_exit(void) +{ + spi_unregister_driver(&max3107_driver); +} + +module_init(max3107_init); +module_exit(max3107_exit); + +MODULE_DESCRIPTION("MAX3107 driver"); +MODULE_AUTHOR("Aavamobile"); +MODULE_ALIAS("aava-max3107-spi"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/serial/max3107.c b/drivers/serial/max3107.c new file mode 100644 index 00000000000..67283c1a57f --- /dev/null +++ b/drivers/serial/max3107.c @@ -0,0 +1,1197 @@ +/* + * max3107.c - spi uart protocol driver for Maxim 3107 + * Based on max3100.c + * by Christian Pellegrin <chripell@evolware.org> + * and max3110.c + * by Feng Tang <feng.tang@intel.com> + * + * Copyright (C) Aavamobile 2009 + * + * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA + * + * ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + * + */ + +#include <linux/delay.h> +#include <linux/device.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/gpio.h> +#include <linux/spi/spi.h> +#include <linux/freezer.h> +#include "max3107.h" + +static const struct baud_table brg26_ext[] = { + { 300, MAX3107_BRG26_B300 }, + { 600, MAX3107_BRG26_B600 }, + { 1200, MAX3107_BRG26_B1200 }, + { 2400, MAX3107_BRG26_B2400 }, + { 4800, MAX3107_BRG26_B4800 }, + { 9600, MAX3107_BRG26_B9600 }, + { 19200, MAX3107_BRG26_B19200 }, + { 57600, MAX3107_BRG26_B57600 }, + { 115200, MAX3107_BRG26_B115200 }, + { 230400, MAX3107_BRG26_B230400 }, + { 460800, MAX3107_BRG26_B460800 }, + { 921600, MAX3107_BRG26_B921600 }, + { 0, 0 } +}; + +static const struct baud_table brg13_int[] = { + { 300, MAX3107_BRG13_IB300 }, + { 600, MAX3107_BRG13_IB600 }, + { 1200, MAX3107_BRG13_IB1200 }, + { 2400, MAX3107_BRG13_IB2400 }, + { 4800, MAX3107_BRG13_IB4800 }, + { 9600, MAX3107_BRG13_IB9600 }, + { 19200, MAX3107_BRG13_IB19200 }, + { 57600, MAX3107_BRG13_IB57600 }, + { 115200, MAX3107_BRG13_IB115200 }, + { 230400, MAX3107_BRG13_IB230400 }, + { 460800, MAX3107_BRG13_IB460800 }, + { 921600, MAX3107_BRG13_IB921600 }, + { 0, 0 } +}; + +static u32 get_new_brg(int baud, struct max3107_port *s) +{ + int i; + const struct baud_table *baud_tbl = s->baud_tbl; + + for (i = 0; i < 13; i++) { + if (baud == baud_tbl[i].baud) + return baud_tbl[i].new_brg; + } + + return 0; +} + +/* Perform SPI transfer for write/read of device register(s) */ +int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len) +{ + struct spi_message spi_msg; + struct spi_transfer spi_xfer; + + /* Initialize SPI ,message */ + spi_message_init(&spi_msg); + + /* Initialize SPI transfer */ + memset(&spi_xfer, 0, sizeof spi_xfer); + spi_xfer.len = len; + spi_xfer.tx_buf = tx; + spi_xfer.rx_buf = rx; + spi_xfer.speed_hz = MAX3107_SPI_SPEED; + + /* Add SPI transfer to SPI message */ + spi_message_add_tail(&spi_xfer, &spi_msg); + +#ifdef DBG_TRACE_SPI_DATA + { + int i; + pr_info("tx len %d:\n", spi_xfer.len); + for (i = 0 ; i < spi_xfer.len && i < 32 ; i++) + pr_info(" %x", ((u8 *)spi_xfer.tx_buf)[i]); + pr_info("\n"); + } +#endif + + /* Perform synchronous SPI transfer */ + if (spi_sync(s->spi, &spi_msg)) { + dev_err(&s->spi->dev, "spi_sync failure\n"); + return -EIO; + } + +#ifdef DBG_TRACE_SPI_DATA + if (spi_xfer.rx_buf) { + int i; + pr_info("rx len %d:\n", spi_xfer.len); + for (i = 0 ; i < spi_xfer.len && i < 32 ; i++) + pr_info(" %x", ((u8 *)spi_xfer.rx_buf)[i]); + pr_info("\n"); + } +#endif + return 0; +} +EXPORT_SYMBOL_GPL(max3107_rw); + +/* Puts received data to circular buffer */ +static void put_data_to_circ_buf(struct max3107_port *s, unsigned char *data, + int len) +{ + struct uart_port *port = &s->port; + struct tty_struct *tty; + + if (!port->state) + return; + + tty = port->state->port.tty; + if (!tty) + return; + + /* Insert received data */ + tty_insert_flip_string(tty, data, len); + /* Update RX counter */ + port->icount.rx += len; +} + +/* Handle data receiving */ +static void max3107_handlerx(struct max3107_port *s, u16 rxlvl) +{ + int i; + int j; + int len; /* SPI transfer buffer length */ + u16 *buf; + u8 *valid_str; + + if (!s->rx_enabled) + /* RX is disabled */ + return; + + if (rxlvl == 0) { + /* RX fifo is empty */ + return; + } else if (rxlvl >= MAX3107_RX_FIFO_SIZE) { + dev_warn(&s->spi->dev, "Possible RX FIFO overrun %d\n", rxlvl); + /* Ensure sanity of RX level */ + rxlvl = MAX3107_RX_FIFO_SIZE; + } + if ((s->rxbuf == 0) || (s->rxstr == 0)) { + dev_warn(&s->spi->dev, "Rx buffer/str isn't ready\n"); + return; + } + buf = s->rxbuf; + valid_str = s->rxstr; + while (rxlvl) { + pr_debug("rxlvl %d\n", rxlvl); + /* Clear buffer */ + memset(buf, 0, sizeof(u16) * (MAX3107_RX_FIFO_SIZE + 2)); + len = 0; + if (s->irqen_reg & MAX3107_IRQ_RXFIFO_BIT) { + /* First disable RX FIFO interrupt */ + pr_debug("Disabling RX INT\n"); + buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); + s->irqen_reg &= ~MAX3107_IRQ_RXFIFO_BIT; + buf[0] |= s->irqen_reg; + len++; + } + /* Just increase the length by amount of words in FIFO since + * buffer was zeroed and SPI transfer of 0x0000 means reading + * from RX FIFO + */ + len += rxlvl; + /* Append RX level query */ + buf[len] = MAX3107_RXFIFOLVL_REG; + len++; + + /* Perform the SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, len * 2)) { + dev_err(&s->spi->dev, "SPI transfer for RX h failed\n"); + return; + } + + /* Skip RX FIFO interrupt disabling word if it was added */ + j = ((len - 1) - rxlvl); + /* Read received words */ + for (i = 0; i < rxlvl; i++, j++) + valid_str[i] = (u8)buf[j]; + put_data_to_circ_buf(s, valid_str, rxlvl); + /* Get new RX level */ + rxlvl = (buf[len - 1] & MAX3107_SPI_RX_DATA_MASK); + } + + if (s->rx_enabled) { + /* RX still enabled, re-enable RX FIFO interrupt */ + pr_debug("Enabling RX INT\n"); + buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); + s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT; + buf[0] |= s->irqen_reg; + if (max3107_rw(s, (u8 *)buf, NULL, 2)) + dev_err(&s->spi->dev, "RX FIFO INT enabling failed\n"); + } + + /* Push the received data to receivers */ + if (s->port.state->port.tty) + tty_flip_buffer_push(s->port.state->port.tty); +} + + +/* Handle data sending */ +static void max3107_handletx(struct max3107_port *s) +{ + struct circ_buf *xmit = &s->port.state->xmit; + int i; + unsigned long flags; + int len; /* SPI transfer buffer length */ + u16 *buf; + + if (!s->tx_fifo_empty) + /* Don't send more data before previous data is sent */ + return; + + if (uart_circ_empty(xmit) || uart_tx_stopped(&s->port)) + /* No data to send or TX is stopped */ + return; + + if (!s->txbuf) { + dev_warn(&s->spi->dev, "Txbuf isn't ready\n"); + return; + } + buf = s->txbuf; + /* Get length of data pending in circular buffer */ + len = uart_circ_chars_pending(xmit); + if (len) { + /* Limit to size of TX FIFO */ + if (len > MAX3107_TX_FIFO_SIZE) + len = MAX3107_TX_FIFO_SIZE; + + pr_debug("txlen %d\n", len); + + /* Update TX counter */ + s->port.icount.tx += len; + + /* TX FIFO will no longer be empty */ + s->tx_fifo_empty = 0; + + i = 0; + if (s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT) { + /* First disable TX empty interrupt */ + pr_debug("Disabling TE INT\n"); + buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); + s->irqen_reg &= ~MAX3107_IRQ_TXEMPTY_BIT; + buf[i] |= s->irqen_reg; + i++; + len++; + } + /* Add data to send */ + spin_lock_irqsave(&s->port.lock, flags); + for ( ; i < len ; i++) { + buf[i] = (MAX3107_WRITE_BIT | MAX3107_THR_REG); + buf[i] |= ((u16)xmit->buf[xmit->tail] & + MAX3107_SPI_TX_DATA_MASK); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + } + spin_unlock_irqrestore(&s->port.lock, flags); + if (!(s->irqen_reg & MAX3107_IRQ_TXEMPTY_BIT)) { + /* Enable TX empty interrupt */ + pr_debug("Enabling TE INT\n"); + buf[i] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG); + s->irqen_reg |= MAX3107_IRQ_TXEMPTY_BIT; + buf[i] |= s->irqen_reg; + i++; + len++; + } + if (!s->tx_enabled) { + /* Enable TX */ + pr_debug("Enable TX\n"); + buf[i] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); + spin_lock_irqsave(&s->data_lock, flags); + s->mode1_reg &= ~MAX3107_MODE1_TXDIS_BIT; + buf[i] |= s->mode1_reg; + spin_unlock_irqrestore(&s->data_lock, flags); + s->tx_enabled = 1; + i++; + len++; + } + + /* Perform the SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, len*2)) { + dev_err(&s->spi->dev, + "SPI transfer TX handling failed\n"); + return; + } + } + + /* Indicate wake up if circular buffer is getting low on data */ + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&s->port); + +} + +/* Handle interrupts + * Also reads and returns current RX FIFO level + */ +static u16 handle_interrupt(struct max3107_port *s) +{ + u16 buf[4]; /* Buffer for SPI transfers */ + u8 irq_status; + u16 rx_level; + unsigned long flags; + + /* Read IRQ status register */ + buf[0] = MAX3107_IRQSTS_REG; + /* Read status IRQ status register */ + buf[1] = MAX3107_STS_IRQSTS_REG; + /* Read LSR IRQ status register */ + buf[2] = MAX3107_LSR_IRQSTS_REG; + /* Query RX level */ + buf[3] = MAX3107_RXFIFOLVL_REG; + + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 8)) { + dev_err(&s->spi->dev, + "SPI transfer for INTR handling failed\n"); + return 0; + } + + irq_status = (u8)buf[0]; + pr_debug("IRQSTS %x\n", irq_status); + rx_level = (buf[3] & MAX3107_SPI_RX_DATA_MASK); + + if (irq_status & MAX3107_IRQ_LSR_BIT) { + /* LSR interrupt */ + if (buf[2] & MAX3107_LSR_RXTO_BIT) + /* RX timeout interrupt, + * handled by normal RX handling + */ + pr_debug("RX TO INT\n"); + } + + if (irq_status & MAX3107_IRQ_TXEMPTY_BIT) { + /* Tx empty interrupt, + * disable TX and set tx_fifo_empty flag + */ + pr_debug("TE INT, disabling TX\n"); + buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); + spin_lock_irqsave(&s->data_lock, flags); + s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT; + buf[0] |= s->mode1_reg; + spin_unlock_irqrestore(&s->data_lock, flags); + if (max3107_rw(s, (u8 *)buf, NULL, 2)) + dev_err(&s->spi->dev, "SPI transfer TX dis failed\n"); + s->tx_enabled = 0; + s->tx_fifo_empty = 1; + } + + if (irq_status & MAX3107_IRQ_RXFIFO_BIT) + /* RX FIFO interrupt, + * handled by normal RX handling + */ + pr_debug("RFIFO INT\n"); + + /* Return RX level */ + return rx_level; +} + +/* Trigger work thread*/ +static void max3107_dowork(struct max3107_port *s) +{ + if (!work_pending(&s->work) && !freezing(current) && !s->suspended) + queue_work(s->workqueue, &s->work); + else + dev_warn(&s->spi->dev, "interrup isn't serviced normally!\n"); +} + +/* Work thread */ +static void max3107_work(struct work_struct *w) +{ + struct max3107_port *s = container_of(w, struct max3107_port, work); + u16 rxlvl = 0; + int len; /* SPI transfer buffer length */ + u16 buf[5]; /* Buffer for SPI transfers */ + unsigned long flags; + + /* Start by reading current RX FIFO level */ + buf[0] = MAX3107_RXFIFOLVL_REG; + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { + dev_err(&s->spi->dev, "SPI transfer RX lev failed\n"); + rxlvl = 0; + } else { + rxlvl = (buf[0] & MAX3107_SPI_RX_DATA_MASK); + } + + do { + pr_debug("rxlvl %d\n", rxlvl); + + /* Handle RX */ + max3107_handlerx(s, rxlvl); + rxlvl = 0; + + if (s->handle_irq) { + /* Handle pending interrupts + * We also get new RX FIFO level since new data may + * have been received while pushing received data to + * receivers + */ + s->handle_irq = 0; + rxlvl = handle_interrupt(s); + } + + /* Handle TX */ + max3107_handletx(s); + + /* Handle configuration changes */ + len = 0; + spin_lock_irqsave(&s->data_lock, flags); + if (s->mode1_commit) { + pr_debug("mode1_commit\n"); + buf[len] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); + buf[len++] |= s->mode1_reg; + s->mode1_commit = 0; + } + if (s->lcr_commit) { + pr_debug("lcr_commit\n"); + buf[len] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG); + buf[len++] |= s->lcr_reg; + s->lcr_commit = 0; + } + if (s->brg_commit) { + pr_debug("brg_commit\n"); + buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG); + buf[len++] |= ((s->brg_cfg >> 16) & + MAX3107_SPI_TX_DATA_MASK); + buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG); + buf[len++] |= ((s->brg_cfg >> 8) & + MAX3107_SPI_TX_DATA_MASK); + buf[len] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG); + buf[len++] |= ((s->brg_cfg) & 0xff); + s->brg_commit = 0; + } + spin_unlock_irqrestore(&s->data_lock, flags); + + if (len > 0) { + if (max3107_rw(s, (u8 *)buf, NULL, len * 2)) + dev_err(&s->spi->dev, + "SPI transfer config failed\n"); + } + + /* Reloop if interrupt handling indicated data in RX FIFO */ + } while (rxlvl); + +} + +/* Set sleep mode */ +static void max3107_set_sleep(struct max3107_port *s, int mode) +{ + u16 buf[1]; /* Buffer for SPI transfer */ + unsigned long flags; + pr_debug("enter, mode %d\n", mode); + + buf[0] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG); + spin_lock_irqsave(&s->data_lock, flags); + switch (mode) { + case MAX3107_DISABLE_FORCED_SLEEP: + s->mode1_reg &= ~MAX3107_MODE1_FORCESLEEP_BIT; + break; + case MAX3107_ENABLE_FORCED_SLEEP: + s->mode1_reg |= MAX3107_MODE1_FORCESLEEP_BIT; + break; + case MAX3107_DISABLE_AUTOSLEEP: + s->mode1_reg &= ~MAX3107_MODE1_AUTOSLEEP_BIT; + break; + case MAX3107_ENABLE_AUTOSLEEP: + s->mode1_reg |= MAX3107_MODE1_AUTOSLEEP_BIT; + break; + default: + spin_unlock_irqrestore(&s->data_lock, flags); + dev_warn(&s->spi->dev, "invalid sleep mode\n"); + return; + } + buf[0] |= s->mode1_reg; + spin_unlock_irqrestore(&s->data_lock, flags); + + if (max3107_rw(s, (u8 *)buf, NULL, 2)) + dev_err(&s->spi->dev, "SPI transfer sleep mode failed\n"); + + if (mode == MAX3107_DISABLE_AUTOSLEEP || + mode == MAX3107_DISABLE_FORCED_SLEEP) + msleep(MAX3107_WAKEUP_DELAY); +} + +/* Perform full register initialization */ +static void max3107_register_init(struct max3107_port *s) +{ + u16 buf[11]; /* Buffer for SPI transfers */ + + /* 1. Configure baud rate, 9600 as default */ + s->baud = 9600; + /* the below is default*/ + if (s->ext_clk) { + s->brg_cfg = MAX3107_BRG26_B9600; + s->baud_tbl = (struct baud_table *)brg26_ext; + } else { + s->brg_cfg = MAX3107_BRG13_IB9600; + s->baud_tbl = (struct baud_table *)brg13_int; + } + + if (s->pdata->init) + s->pdata->init(s); + + buf[0] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVMSB_REG) + | ((s->brg_cfg >> 16) & MAX3107_SPI_TX_DATA_MASK); + buf[1] = (MAX3107_WRITE_BIT | MAX3107_BRGDIVLSB_REG) + | ((s->brg_cfg >> 8) & MAX3107_SPI_TX_DATA_MASK); + buf[2] = (MAX3107_WRITE_BIT | MAX3107_BRGCFG_REG) + | ((s->brg_cfg) & 0xff); + + /* 2. Configure LCR register, 8N1 mode by default */ + s->lcr_reg = MAX3107_LCR_WORD_LEN_8; + buf[3] = (MAX3107_WRITE_BIT | MAX3107_LCR_REG) + | s->lcr_reg; + + /* 3. Configure MODE 1 register */ + s->mode1_reg = 0; + /* Enable IRQ pin */ + s->mode1_reg |= MAX3107_MODE1_IRQSEL_BIT; + /* Disable TX */ + s->mode1_reg |= MAX3107_MODE1_TXDIS_BIT; + s->tx_enabled = 0; + /* RX is enabled */ + s->rx_enabled = 1; + buf[4] = (MAX3107_WRITE_BIT | MAX3107_MODE1_REG) + | s->mode1_reg; + + /* 4. Configure MODE 2 register */ + buf[5] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG); + if (s->loopback) { + /* Enable loopback */ + buf[5] |= MAX3107_MODE2_LOOPBACK_BIT; + } + /* Reset FIFOs */ + buf[5] |= MAX3107_MODE2_FIFORST_BIT; + s->tx_fifo_empty = 1; + + /* 5. Configure FIFO trigger level register */ + buf[6] = (MAX3107_WRITE_BIT | MAX3107_FIFOTRIGLVL_REG); + /* RX FIFO trigger for 16 words, TX FIFO trigger not used */ + buf[6] |= (MAX3107_FIFOTRIGLVL_RX(16) | MAX3107_FIFOTRIGLVL_TX(0)); + + /* 6. Configure flow control levels */ + buf[7] = (MAX3107_WRITE_BIT | MAX3107_FLOWLVL_REG); + /* Flow control halt level 96, resume level 48 */ + buf[7] |= (MAX3107_FLOWLVL_RES(48) | MAX3107_FLOWLVL_HALT(96)); + + /* 7. Configure flow control */ + buf[8] = (MAX3107_WRITE_BIT | MAX3107_FLOWCTRL_REG); + /* Enable auto CTS and auto RTS flow control */ + buf[8] |= (MAX3107_FLOWCTRL_AUTOCTS_BIT | MAX3107_FLOWCTRL_AUTORTS_BIT); + + /* 8. Configure RX timeout register */ + buf[9] = (MAX3107_WRITE_BIT | MAX3107_RXTO_REG); + /* Timeout after 48 character intervals */ + buf[9] |= 0x0030; + + /* 9. Configure LSR interrupt enable register */ + buf[10] = (MAX3107_WRITE_BIT | MAX3107_LSR_IRQEN_REG); + /* Enable RX timeout interrupt */ + buf[10] |= MAX3107_LSR_RXTO_BIT; + + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 22)) + dev_err(&s->spi->dev, "SPI transfer for init failed\n"); + + /* 10. Clear IRQ status register by reading it */ + buf[0] = MAX3107_IRQSTS_REG; + + /* 11. Configure interrupt enable register */ + /* Enable LSR interrupt */ + s->irqen_reg = MAX3107_IRQ_LSR_BIT; + /* Enable RX FIFO interrupt */ + s->irqen_reg |= MAX3107_IRQ_RXFIFO_BIT; + buf[1] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG) + | s->irqen_reg; + + /* 12. Clear FIFO reset that was set in step 6 */ + buf[2] = (MAX3107_WRITE_BIT | MAX3107_MODE2_REG); + if (s->loopback) { + /* Keep loopback enabled */ + buf[2] |= MAX3107_MODE2_LOOPBACK_BIT; + } + + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 6)) + dev_err(&s->spi->dev, "SPI transfer for init failed\n"); + +} + +/* IRQ handler */ +static irqreturn_t max3107_irq(int irqno, void *dev_id) +{ + struct max3107_port *s = dev_id; + + if (irqno != s->spi->irq) { + /* Unexpected IRQ */ + return IRQ_NONE; + } + + /* Indicate irq */ + s->handle_irq = 1; + + /* Trigger work thread */ + max3107_dowork(s); + + return IRQ_HANDLED; +} + +/* HW suspension function + * + * Currently autosleep is used to decrease current consumption, alternative + * approach would be to set the chip to reset mode if UART is not being + * used but that would mess the GPIOs + * + */ +void max3107_hw_susp(struct max3107_port *s, int suspend) +{ + pr_debug("enter, suspend %d\n", suspend); + + if (suspend) { + /* Suspend requested, + * enable autosleep to decrease current consumption + */ + s->suspended = 1; + max3107_set_sleep(s, MAX3107_ENABLE_AUTOSLEEP); + } else { + /* Resume requested, + * disable autosleep + */ + s->suspended = 0; + max3107_set_sleep(s, MAX3107_DISABLE_AUTOSLEEP); + } +} +EXPORT_SYMBOL_GPL(max3107_hw_susp); + +/* Modem status IRQ enabling */ +static void max3107_enable_ms(struct uart_port *port) +{ + /* Modem status not supported */ +} + +/* Data send function */ +static void max3107_start_tx(struct uart_port *port) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + + /* Trigger work thread for sending data */ + max3107_dowork(s); +} + +/* Function for checking that there is no pending transfers */ +static unsigned int max3107_tx_empty(struct uart_port *port) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + + pr_debug("returning %d\n", + (s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit))); + return s->tx_fifo_empty && uart_circ_empty(&s->port.state->xmit); +} + +/* Function for stopping RX */ +static void max3107_stop_rx(struct uart_port *port) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + unsigned long flags; + + /* Set RX disabled in MODE 1 register */ + spin_lock_irqsave(&s->data_lock, flags); + s->mode1_reg |= MAX3107_MODE1_RXDIS_BIT; + s->mode1_commit = 1; + spin_unlock_irqrestore(&s->data_lock, flags); + /* Set RX disabled */ + s->rx_enabled = 0; + /* Trigger work thread for doing the actual configuration change */ + max3107_dowork(s); +} + +/* Function for returning control pin states */ +static unsigned int max3107_get_mctrl(struct uart_port *port) +{ + /* DCD and DSR are not wired and CTS/RTS is handled automatically + * so just indicate DSR and CAR asserted + */ + return TIOCM_DSR | TIOCM_CAR; +} + +/* Function for setting control pin states */ +static void max3107_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + /* DCD and DSR are not wired and CTS/RTS is hadnled automatically + * so do nothing + */ +} + +/* Function for configuring UART parameters */ +static void max3107_set_termios(struct uart_port *port, + struct ktermios *termios, + struct ktermios *old) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + struct tty_struct *tty; + int baud; + u16 new_lcr = 0; + u32 new_brg = 0; + unsigned long flags; + + if (!port->state) + return; + + tty = port->state->port.tty; + if (!tty) + return; + + /* Get new LCR register values */ + /* Word size */ + if ((termios->c_cflag & CSIZE) == CS7) + new_lcr |= MAX3107_LCR_WORD_LEN_7; + else + new_lcr |= MAX3107_LCR_WORD_LEN_8; + + /* Parity */ + if (termios->c_cflag & PARENB) { + new_lcr |= MAX3107_LCR_PARITY_BIT; + if (!(termios->c_cflag & PARODD)) + new_lcr |= MAX3107_LCR_EVENPARITY_BIT; + } + + /* Stop bits */ + if (termios->c_cflag & CSTOPB) { + /* 2 stop bits */ + new_lcr |= MAX3107_LCR_STOPLEN_BIT; + } + + /* Mask termios capabilities we don't support */ + termios->c_cflag &= ~CMSPAR; + + /* Set status ignore mask */ + s->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + s->port.ignore_status_mask |= MAX3107_ALL_ERRORS; + + /* Set low latency to immediately handle pushed data */ + s->port.state->port.tty->low_latency = 1; + + /* Get new baud rate generator configuration */ + baud = tty_get_baud_rate(tty); + + spin_lock_irqsave(&s->data_lock, flags); + new_brg = get_new_brg(baud, s); + /* if can't find the corrent config, use previous */ + if (!new_brg) { + baud = s->baud; + new_brg = s->brg_cfg; + } + spin_unlock_irqrestore(&s->data_lock, flags); + tty_termios_encode_baud_rate(termios, baud, baud); + s->baud = baud; + + /* Update timeout according to new baud rate */ + uart_update_timeout(port, termios->c_cflag, baud); + + spin_lock_irqsave(&s->data_lock, flags); + if (s->lcr_reg != new_lcr) { + s->lcr_reg = new_lcr; + s->lcr_commit = 1; + } + if (s->brg_cfg != new_brg) { + s->brg_cfg = new_brg; + s->brg_commit = 1; + } + spin_unlock_irqrestore(&s->data_lock, flags); + + /* Trigger work thread for doing the actual configuration change */ + max3107_dowork(s); +} + +/* Port shutdown function */ +static void max3107_shutdown(struct uart_port *port) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + + if (s->suspended && s->pdata->hw_suspend) + s->pdata->hw_suspend(s, 0); + + /* Free the interrupt */ + free_irq(s->spi->irq, s); + + if (s->workqueue) { + /* Flush and destroy work queue */ + flush_workqueue(s->workqueue); + destroy_workqueue(s->workqueue); + s->workqueue = NULL; + } + + /* Suspend HW */ + if (s->pdata->hw_suspend) + s->pdata->hw_suspend(s, 1); +} + +/* Port startup function */ +static int max3107_startup(struct uart_port *port) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + + /* Initialize work queue */ + s->workqueue = create_freezeable_workqueue("max3107"); + if (!s->workqueue) { + dev_err(&s->spi->dev, "Workqueue creation failed\n"); + return -EBUSY; + } + INIT_WORK(&s->work, max3107_work); + + /* Setup IRQ */ + if (request_irq(s->spi->irq, max3107_irq, IRQF_TRIGGER_FALLING, + "max3107", s)) { + dev_err(&s->spi->dev, "IRQ reguest failed\n"); + destroy_workqueue(s->workqueue); + s->workqueue = NULL; + return -EBUSY; + } + + /* Resume HW */ + if (s->pdata->hw_suspend) + s->pdata->hw_suspend(s, 0); + + /* Init registers */ + max3107_register_init(s); + + return 0; +} + +/* Port type function */ +static const char *max3107_type(struct uart_port *port) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + return s->spi->modalias; +} + +/* Port release function */ +static void max3107_release_port(struct uart_port *port) +{ + /* Do nothing */ +} + +/* Port request function */ +static int max3107_request_port(struct uart_port *port) +{ + /* Do nothing */ + return 0; +} + +/* Port config function */ +static void max3107_config_port(struct uart_port *port, int flags) +{ + struct max3107_port *s = container_of(port, struct max3107_port, port); + s->port.type = PORT_MAX3107; +} + +/* Port verify function */ +static int max3107_verify_port(struct uart_port *port, + struct serial_struct *ser) +{ + if (ser->type == PORT_UNKNOWN || ser->type == PORT_MAX3107) + return 0; + + return -EINVAL; +} + +/* Port stop TX function */ +static void max3107_stop_tx(struct uart_port *port) +{ + /* Do nothing */ +} + +/* Port break control function */ +static void max3107_break_ctl(struct uart_port *port, int break_state) +{ + /* We don't support break control, do nothing */ +} + + +/* Port functions */ +static struct uart_ops max3107_ops = { + .tx_empty = max3107_tx_empty, + .set_mctrl = max3107_set_mctrl, + .get_mctrl = max3107_get_mctrl, + .stop_tx = max3107_stop_tx, + .start_tx = max3107_start_tx, + .stop_rx = max3107_stop_rx, + .enable_ms = max3107_enable_ms, + .break_ctl = max3107_break_ctl, + .startup = max3107_startup, + .shutdown = max3107_shutdown, + .set_termios = max3107_set_termios, + .type = max3107_type, + .release_port = max3107_release_port, + .request_port = max3107_request_port, + .config_port = max3107_config_port, + .verify_port = max3107_verify_port, +}; + +/* UART driver data */ +static struct uart_driver max3107_uart_driver = { + .owner = THIS_MODULE, + .driver_name = "ttyMAX", + .dev_name = "ttyMAX", + .nr = 1, +}; + +static int driver_registered = 0; + + + +/* 'Generic' platform data */ +static struct max3107_plat generic_plat_data = { + .loopback = 0, + .ext_clk = 1, + .hw_suspend = max3107_hw_susp, + .polled_mode = 0, + .poll_time = 0, +}; + + +/*******************************************************************/ + +/** + * max3107_probe - SPI bus probe entry point + * @spi: the spi device + * + * SPI wants us to probe this device and if appropriate claim it. + * Perform any platform specific requirements and then initialise + * the device. + */ + +int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata) +{ + struct max3107_port *s; + u16 buf[2]; /* Buffer for SPI transfers */ + int retval; + + pr_info("enter max3107 probe\n"); + + /* Allocate port structure */ + s = kzalloc(sizeof(*s), GFP_KERNEL); + if (!s) { + pr_err("Allocating port structure failed\n"); + return -ENOMEM; + } + + s->pdata = pdata; + + /* SPI Rx buffer + * +2 for RX FIFO interrupt + * disabling and RX level query + */ + s->rxbuf = kzalloc(sizeof(u16) * (MAX3107_RX_FIFO_SIZE+2), GFP_KERNEL); + if (!s->rxbuf) { + pr_err("Allocating RX buffer failed\n"); + return -ENOMEM; + } + s->rxstr = kzalloc(sizeof(u8) * MAX3107_RX_FIFO_SIZE, GFP_KERNEL); + if (!s->rxstr) { + pr_err("Allocating RX buffer failed\n"); + return -ENOMEM; + } + /* SPI Tx buffer + * SPI transfer buffer + * +3 for TX FIFO empty + * interrupt disabling and + * enabling and TX enabling + */ + s->txbuf = kzalloc(sizeof(u16) * MAX3107_TX_FIFO_SIZE + 3, GFP_KERNEL); + if (!s->txbuf) { + pr_err("Allocating TX buffer failed\n"); + return -ENOMEM; + } + /* Initialize shared data lock */ + spin_lock_init(&s->data_lock); + + /* SPI intializations */ + dev_set_drvdata(&spi->dev, s); + spi->mode = SPI_MODE_0; + spi->dev.platform_data = pdata; + spi->bits_per_word = 16; + s->ext_clk = pdata->ext_clk; + s->loopback = pdata->loopback; + spi_setup(spi); + s->spi = spi; + + /* Check REV ID to ensure we are talking to what we expect */ + buf[0] = MAX3107_REVID_REG; + if (max3107_rw(s, (u8 *)buf, (u8 *)buf, 2)) { + dev_err(&s->spi->dev, "SPI transfer for REVID read failed\n"); + return -EIO; + } + if ((buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID1 && + (buf[0] & MAX3107_SPI_RX_DATA_MASK) != MAX3107_REVID2) { + dev_err(&s->spi->dev, "REVID %x does not match\n", + (buf[0] & MAX3107_SPI_RX_DATA_MASK)); + return -ENODEV; + } + + /* Disable all interrupts */ + buf[0] = (MAX3107_WRITE_BIT | MAX3107_IRQEN_REG | 0x0000); + buf[0] |= 0x0000; + + /* Configure clock source */ + buf[1] = (MAX3107_WRITE_BIT | MAX3107_CLKSRC_REG); + if (s->ext_clk) { + /* External clock */ + buf[1] |= MAX3107_CLKSRC_EXTCLK_BIT; + } + + /* PLL bypass ON */ + buf[1] |= MAX3107_CLKSRC_PLLBYP_BIT; + + /* Perform SPI transfer */ + if (max3107_rw(s, (u8 *)buf, NULL, 4)) { + dev_err(&s->spi->dev, "SPI transfer for init failed\n"); + return -EIO; + } + + /* Register UART driver */ + if (!driver_registered) { + retval = uart_register_driver(&max3107_uart_driver); + if (retval) { + dev_err(&s->spi->dev, "Registering UART driver failed\n"); + return retval; + } + driver_registered = 1; + } + + /* Initialize UART port data */ + s->port.fifosize = 128; + s->port.ops = &max3107_ops; + s->port.line = 0; + s->port.dev = &spi->dev; + s->port.uartclk = 9600; + s->port.flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF; + s->port.irq = s->spi->irq; + s->port.type = PORT_MAX3107; + + /* Add UART port */ + retval = uart_add_one_port(&max3107_uart_driver, &s->port); + if (retval < 0) { + dev_err(&s->spi->dev, "Adding UART port failed\n"); + return retval; + } + + if (pdata->configure) { + retval = pdata->configure(s); + if (retval < 0) + return retval; + } + + /* Go to suspend mode */ + if (pdata->hw_suspend) + pdata->hw_suspend(s, 1); + + return 0; +} +EXPORT_SYMBOL_GPL(max3107_probe); + +/* Driver remove function */ +int max3107_remove(struct spi_device *spi) +{ + struct max3107_port *s = dev_get_drvdata(&spi->dev); + + pr_info("enter max3107 remove\n"); + + /* Remove port */ + if (uart_remove_one_port(&max3107_uart_driver, &s->port)) + dev_warn(&s->spi->dev, "Removing UART port failed\n"); + + + /* Free TxRx buffer */ + kfree(s->rxbuf); + kfree(s->rxstr); + kfree(s->txbuf); + + /* Free port structure */ + kfree(s); + + return 0; +} +EXPORT_SYMBOL_GPL(max3107_remove); + +/* Driver suspend function */ +int max3107_suspend(struct spi_device *spi, pm_message_t state) +{ +#ifdef CONFIG_PM + struct max3107_port *s = dev_get_drvdata(&spi->dev); + + pr_debug("enter suspend\n"); + + /* Suspend UART port */ + uart_suspend_port(&max3107_uart_driver, &s->port); + + /* Go to suspend mode */ + if (s->pdata->hw_suspend) + s->pdata->hw_suspend(s, 1); +#endif /* CONFIG_PM */ + return 0; +} +EXPORT_SYMBOL_GPL(max3107_suspend); + +/* Driver resume function */ +int max3107_resume(struct spi_device *spi) +{ +#ifdef CONFIG_PM + struct max3107_port *s = dev_get_drvdata(&spi->dev); + + pr_debug("enter resume\n"); + + /* Resume from suspend */ + if (s->pdata->hw_suspend) + s->pdata->hw_suspend(s, 0); + + /* Resume UART port */ + uart_resume_port(&max3107_uart_driver, &s->port); +#endif /* CONFIG_PM */ + return 0; +} +EXPORT_SYMBOL_GPL(max3107_resume); + +static int max3107_probe_generic(struct spi_device *spi) +{ + return max3107_probe(spi, &generic_plat_data); +} + +/* Spi driver data */ +static struct spi_driver max3107_driver = { + .driver = { + .name = "max3107", + .bus = &spi_bus_type, + .owner = THIS_MODULE, + }, + .probe = max3107_probe_generic, + .remove = __devexit_p(max3107_remove), + .suspend = max3107_suspend, + .resume = max3107_resume, +}; + +/* Driver init function */ +static int __init max3107_init(void) +{ + pr_info("enter max3107 init\n"); + return spi_register_driver(&max3107_driver); +} + +/* Driver exit function */ +static void __exit max3107_exit(void) +{ + pr_info("enter max3107 exit\n"); + /* Unregister UART driver */ + if (driver_registered) + uart_unregister_driver(&max3107_uart_driver); + spi_unregister_driver(&max3107_driver); +} + +module_init(max3107_init); +module_exit(max3107_exit); + +MODULE_DESCRIPTION("MAX3107 driver"); +MODULE_AUTHOR("Aavamobile"); +MODULE_ALIAS("max3107-spi"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/serial/max3107.h b/drivers/serial/max3107.h new file mode 100644 index 00000000000..7ab63239250 --- /dev/null +++ b/drivers/serial/max3107.h @@ -0,0 +1,441 @@ +/* + * max3107.h - spi uart protocol driver header for Maxim 3107 + * + * Copyright (C) Aavamobile 2009 + * Based on serial_max3100.h by Christian Pellegrin + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#ifndef _MAX3107_H +#define _MAX3107_H + +/* Serial error status definitions */ +#define MAX3107_PARITY_ERROR 1 +#define MAX3107_FRAME_ERROR 2 +#define MAX3107_OVERRUN_ERROR 4 +#define MAX3107_ALL_ERRORS (MAX3107_PARITY_ERROR | \ + MAX3107_FRAME_ERROR | \ + MAX3107_OVERRUN_ERROR) + +/* GPIO definitions */ +#define MAX3107_GPIO_BASE 88 +#define MAX3107_GPIO_COUNT 4 + + +/* GPIO connected to chip's reset pin */ +#define MAX3107_RESET_GPIO 87 + + +/* Chip reset delay */ +#define MAX3107_RESET_DELAY 10 + +/* Chip wakeup delay */ +#define MAX3107_WAKEUP_DELAY 50 + + +/* Sleep mode definitions */ +#define MAX3107_DISABLE_FORCED_SLEEP 0 +#define MAX3107_ENABLE_FORCED_SLEEP 1 +#define MAX3107_DISABLE_AUTOSLEEP 2 +#define MAX3107_ENABLE_AUTOSLEEP 3 + + +/* Definitions for register access with SPI transfers + * + * SPI transfer format: + * + * Master to slave bits xzzzzzzzyyyyyyyy + * Slave to master bits aaaaaaaabbbbbbbb + * + * where: + * x = 0 for reads, 1 for writes + * z = register address + * y = new register value if write, 0 if read + * a = unspecified + * b = register value if read, unspecified if write + */ + +/* SPI speed */ +#define MAX3107_SPI_SPEED (3125000 * 2) + +/* Write bit */ +#define MAX3107_WRITE_BIT (1 << 15) + +/* SPI TX data mask */ +#define MAX3107_SPI_RX_DATA_MASK (0x00ff) + +/* SPI RX data mask */ +#define MAX3107_SPI_TX_DATA_MASK (0x00ff) + +/* Register access masks */ +#define MAX3107_RHR_REG (0x0000) /* RX FIFO */ +#define MAX3107_THR_REG (0x0000) /* TX FIFO */ +#define MAX3107_IRQEN_REG (0x0100) /* IRQ enable */ +#define MAX3107_IRQSTS_REG (0x0200) /* IRQ status */ +#define MAX3107_LSR_IRQEN_REG (0x0300) /* LSR IRQ enable */ +#define MAX3107_LSR_IRQSTS_REG (0x0400) /* LSR IRQ status */ +#define MAX3107_SPCHR_IRQEN_REG (0x0500) /* Special char IRQ enable */ +#define MAX3107_SPCHR_IRQSTS_REG (0x0600) /* Special char IRQ status */ +#define MAX3107_STS_IRQEN_REG (0x0700) /* Status IRQ enable */ +#define MAX3107_STS_IRQSTS_REG (0x0800) /* Status IRQ status */ +#define MAX3107_MODE1_REG (0x0900) /* MODE1 */ +#define MAX3107_MODE2_REG (0x0a00) /* MODE2 */ +#define MAX3107_LCR_REG (0x0b00) /* LCR */ +#define MAX3107_RXTO_REG (0x0c00) /* RX timeout */ +#define MAX3107_HDPIXDELAY_REG (0x0d00) /* Auto transceiver delays */ +#define MAX3107_IRDA_REG (0x0e00) /* IRDA settings */ +#define MAX3107_FLOWLVL_REG (0x0f00) /* Flow control levels */ +#define MAX3107_FIFOTRIGLVL_REG (0x1000) /* FIFO IRQ trigger levels */ +#define MAX3107_TXFIFOLVL_REG (0x1100) /* TX FIFO level */ +#define MAX3107_RXFIFOLVL_REG (0x1200) /* RX FIFO level */ +#define MAX3107_FLOWCTRL_REG (0x1300) /* Flow control */ +#define MAX3107_XON1_REG (0x1400) /* XON1 character */ +#define MAX3107_XON2_REG (0x1500) /* XON2 character */ +#define MAX3107_XOFF1_REG (0x1600) /* XOFF1 character */ +#define MAX3107_XOFF2_REG (0x1700) /* XOFF2 character */ +#define MAX3107_GPIOCFG_REG (0x1800) /* GPIO config */ +#define MAX3107_GPIODATA_REG (0x1900) /* GPIO data */ +#define MAX3107_PLLCFG_REG (0x1a00) /* PLL config */ +#define MAX3107_BRGCFG_REG (0x1b00) /* Baud rate generator conf */ +#define MAX3107_BRGDIVLSB_REG (0x1c00) /* Baud rate divisor LSB */ +#define MAX3107_BRGDIVMSB_REG (0x1d00) /* Baud rate divisor MSB */ +#define MAX3107_CLKSRC_REG (0x1e00) /* Clock source */ +#define MAX3107_REVID_REG (0x1f00) /* Revision identification */ + +/* IRQ register bits */ +#define MAX3107_IRQ_LSR_BIT (1 << 0) /* LSR interrupt */ +#define MAX3107_IRQ_SPCHR_BIT (1 << 1) /* Special char interrupt */ +#define MAX3107_IRQ_STS_BIT (1 << 2) /* Status interrupt */ +#define MAX3107_IRQ_RXFIFO_BIT (1 << 3) /* RX FIFO interrupt */ +#define MAX3107_IRQ_TXFIFO_BIT (1 << 4) /* TX FIFO interrupt */ +#define MAX3107_IRQ_TXEMPTY_BIT (1 << 5) /* TX FIFO empty interrupt */ +#define MAX3107_IRQ_RXEMPTY_BIT (1 << 6) /* RX FIFO empty interrupt */ +#define MAX3107_IRQ_CTS_BIT (1 << 7) /* CTS interrupt */ + +/* LSR register bits */ +#define MAX3107_LSR_RXTO_BIT (1 << 0) /* RX timeout */ +#define MAX3107_LSR_RXOVR_BIT (1 << 1) /* RX overrun */ +#define MAX3107_LSR_RXPAR_BIT (1 << 2) /* RX parity error */ +#define MAX3107_LSR_FRERR_BIT (1 << 3) /* Frame error */ +#define MAX3107_LSR_RXBRK_BIT (1 << 4) /* RX break */ +#define MAX3107_LSR_RXNOISE_BIT (1 << 5) /* RX noise */ +#define MAX3107_LSR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_LSR_CTS_BIT (1 << 7) /* CTS pin state */ + +/* Special character register bits */ +#define MAX3107_SPCHR_XON1_BIT (1 << 0) /* XON1 character */ +#define MAX3107_SPCHR_XON2_BIT (1 << 1) /* XON2 character */ +#define MAX3107_SPCHR_XOFF1_BIT (1 << 2) /* XOFF1 character */ +#define MAX3107_SPCHR_XOFF2_BIT (1 << 3) /* XOFF2 character */ +#define MAX3107_SPCHR_BREAK_BIT (1 << 4) /* RX break */ +#define MAX3107_SPCHR_MULTIDROP_BIT (1 << 5) /* 9-bit multidrop addr char */ +#define MAX3107_SPCHR_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_SPCHR_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* Status register bits */ +#define MAX3107_STS_GPIO0_BIT (1 << 0) /* GPIO 0 interrupt */ +#define MAX3107_STS_GPIO1_BIT (1 << 1) /* GPIO 1 interrupt */ +#define MAX3107_STS_GPIO2_BIT (1 << 2) /* GPIO 2 interrupt */ +#define MAX3107_STS_GPIO3_BIT (1 << 3) /* GPIO 3 interrupt */ +#define MAX3107_STS_UNDEF4_BIT (1 << 4) /* Undefined/not used */ +#define MAX3107_STS_CLKREADY_BIT (1 << 5) /* Clock ready */ +#define MAX3107_STS_SLEEP_BIT (1 << 6) /* Sleep interrupt */ +#define MAX3107_STS_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* MODE1 register bits */ +#define MAX3107_MODE1_RXDIS_BIT (1 << 0) /* RX disable */ +#define MAX3107_MODE1_TXDIS_BIT (1 << 1) /* TX disable */ +#define MAX3107_MODE1_TXHIZ_BIT (1 << 2) /* TX pin three-state */ +#define MAX3107_MODE1_RTSHIZ_BIT (1 << 3) /* RTS pin three-state */ +#define MAX3107_MODE1_TRNSCVCTRL_BIT (1 << 4) /* Transceiver ctrl enable */ +#define MAX3107_MODE1_FORCESLEEP_BIT (1 << 5) /* Force sleep mode */ +#define MAX3107_MODE1_AUTOSLEEP_BIT (1 << 6) /* Auto sleep enable */ +#define MAX3107_MODE1_IRQSEL_BIT (1 << 7) /* IRQ pin enable */ + +/* MODE2 register bits */ +#define MAX3107_MODE2_RST_BIT (1 << 0) /* Chip reset */ +#define MAX3107_MODE2_FIFORST_BIT (1 << 1) /* FIFO reset */ +#define MAX3107_MODE2_RXTRIGINV_BIT (1 << 2) /* RX FIFO INT invert */ +#define MAX3107_MODE2_RXEMPTINV_BIT (1 << 3) /* RX FIFO empty INT invert */ +#define MAX3107_MODE2_SPCHR_BIT (1 << 4) /* Special chr detect enable */ +#define MAX3107_MODE2_LOOPBACK_BIT (1 << 5) /* Internal loopback enable */ +#define MAX3107_MODE2_MULTIDROP_BIT (1 << 6) /* 9-bit multidrop enable */ +#define MAX3107_MODE2_ECHOSUPR_BIT (1 << 7) /* ECHO suppression enable */ + +/* LCR register bits */ +#define MAX3107_LCR_LENGTH0_BIT (1 << 0) /* Word length bit 0 */ +#define MAX3107_LCR_LENGTH1_BIT (1 << 1) /* Word length bit 1 + * + * Word length bits table: + * 00 -> 5 bit words + * 01 -> 6 bit words + * 10 -> 7 bit words + * 11 -> 8 bit words + */ +#define MAX3107_LCR_STOPLEN_BIT (1 << 2) /* STOP length bit + * + * STOP length bit table: + * 0 -> 1 stop bit + * 1 -> 1-1.5 stop bits if + * word length is 5, + * 2 stop bits otherwise + */ +#define MAX3107_LCR_PARITY_BIT (1 << 3) /* Parity bit enable */ +#define MAX3107_LCR_EVENPARITY_BIT (1 << 4) /* Even parity bit enable */ +#define MAX3107_LCR_FORCEPARITY_BIT (1 << 5) /* 9-bit multidrop parity */ +#define MAX3107_LCR_TXBREAK_BIT (1 << 6) /* TX break enable */ +#define MAX3107_LCR_RTS_BIT (1 << 7) /* RTS pin control */ +#define MAX3107_LCR_WORD_LEN_5 (0x0000) +#define MAX3107_LCR_WORD_LEN_6 (0x0001) +#define MAX3107_LCR_WORD_LEN_7 (0x0002) +#define MAX3107_LCR_WORD_LEN_8 (0x0003) + + +/* IRDA register bits */ +#define MAX3107_IRDA_IRDAEN_BIT (1 << 0) /* IRDA mode enable */ +#define MAX3107_IRDA_SIR_BIT (1 << 1) /* SIR mode enable */ +#define MAX3107_IRDA_SHORTIR_BIT (1 << 2) /* Short SIR mode enable */ +#define MAX3107_IRDA_MIR_BIT (1 << 3) /* MIR mode enable */ +#define MAX3107_IRDA_RXINV_BIT (1 << 4) /* RX logic inversion enable */ +#define MAX3107_IRDA_TXINV_BIT (1 << 5) /* TX logic inversion enable */ +#define MAX3107_IRDA_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_IRDA_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* Flow control trigger level register masks */ +#define MAX3107_FLOWLVL_HALT_MASK (0x000f) /* Flow control halt level */ +#define MAX3107_FLOWLVL_RES_MASK (0x00f0) /* Flow control resume level */ +#define MAX3107_FLOWLVL_HALT(words) ((words/8) & 0x000f) +#define MAX3107_FLOWLVL_RES(words) (((words/8) & 0x000f) << 4) + +/* FIFO interrupt trigger level register masks */ +#define MAX3107_FIFOTRIGLVL_TX_MASK (0x000f) /* TX FIFO trigger level */ +#define MAX3107_FIFOTRIGLVL_RX_MASK (0x00f0) /* RX FIFO trigger level */ +#define MAX3107_FIFOTRIGLVL_TX(words) ((words/8) & 0x000f) +#define MAX3107_FIFOTRIGLVL_RX(words) (((words/8) & 0x000f) << 4) + +/* Flow control register bits */ +#define MAX3107_FLOWCTRL_AUTORTS_BIT (1 << 0) /* Auto RTS flow ctrl enable */ +#define MAX3107_FLOWCTRL_AUTOCTS_BIT (1 << 1) /* Auto CTS flow ctrl enable */ +#define MAX3107_FLOWCTRL_GPIADDR_BIT (1 << 2) /* Enables that GPIO inputs + * are used in conjunction with + * XOFF2 for definition of + * special character */ +#define MAX3107_FLOWCTRL_SWFLOWEN_BIT (1 << 3) /* Auto SW flow ctrl enable */ +#define MAX3107_FLOWCTRL_SWFLOW0_BIT (1 << 4) /* SWFLOW bit 0 */ +#define MAX3107_FLOWCTRL_SWFLOW1_BIT (1 << 5) /* SWFLOW bit 1 + * + * SWFLOW bits 1 & 0 table: + * 00 -> no transmitter flow + * control + * 01 -> receiver compares + * XON2 and XOFF2 + * and controls + * transmitter + * 10 -> receiver compares + * XON1 and XOFF1 + * and controls + * transmitter + * 11 -> receiver compares + * XON1, XON2, XOFF1 and + * XOFF2 and controls + * transmitter + */ +#define MAX3107_FLOWCTRL_SWFLOW2_BIT (1 << 6) /* SWFLOW bit 2 */ +#define MAX3107_FLOWCTRL_SWFLOW3_BIT (1 << 7) /* SWFLOW bit 3 + * + * SWFLOW bits 3 & 2 table: + * 00 -> no received flow + * control + * 01 -> transmitter generates + * XON2 and XOFF2 + * 10 -> transmitter generates + * XON1 and XOFF1 + * 11 -> transmitter generates + * XON1, XON2, XOFF1 and + * XOFF2 + */ + +/* GPIO configuration register bits */ +#define MAX3107_GPIOCFG_GP0OUT_BIT (1 << 0) /* GPIO 0 output enable */ +#define MAX3107_GPIOCFG_GP1OUT_BIT (1 << 1) /* GPIO 1 output enable */ +#define MAX3107_GPIOCFG_GP2OUT_BIT (1 << 2) /* GPIO 2 output enable */ +#define MAX3107_GPIOCFG_GP3OUT_BIT (1 << 3) /* GPIO 3 output enable */ +#define MAX3107_GPIOCFG_GP0OD_BIT (1 << 4) /* GPIO 0 open-drain enable */ +#define MAX3107_GPIOCFG_GP1OD_BIT (1 << 5) /* GPIO 1 open-drain enable */ +#define MAX3107_GPIOCFG_GP2OD_BIT (1 << 6) /* GPIO 2 open-drain enable */ +#define MAX3107_GPIOCFG_GP3OD_BIT (1 << 7) /* GPIO 3 open-drain enable */ + +/* GPIO DATA register bits */ +#define MAX3107_GPIODATA_GP0OUT_BIT (1 << 0) /* GPIO 0 output value */ +#define MAX3107_GPIODATA_GP1OUT_BIT (1 << 1) /* GPIO 1 output value */ +#define MAX3107_GPIODATA_GP2OUT_BIT (1 << 2) /* GPIO 2 output value */ +#define MAX3107_GPIODATA_GP3OUT_BIT (1 << 3) /* GPIO 3 output value */ +#define MAX3107_GPIODATA_GP0IN_BIT (1 << 4) /* GPIO 0 input value */ +#define MAX3107_GPIODATA_GP1IN_BIT (1 << 5) /* GPIO 1 input value */ +#define MAX3107_GPIODATA_GP2IN_BIT (1 << 6) /* GPIO 2 input value */ +#define MAX3107_GPIODATA_GP3IN_BIT (1 << 7) /* GPIO 3 input value */ + +/* PLL configuration register masks */ +#define MAX3107_PLLCFG_PREDIV_MASK (0x003f) /* PLL predivision value */ +#define MAX3107_PLLCFG_PLLFACTOR_MASK (0x00c0) /* PLL multiplication factor */ + +/* Baud rate generator configuration register masks and bits */ +#define MAX3107_BRGCFG_FRACT_MASK (0x000f) /* Fractional portion of + * Baud rate generator divisor + */ +#define MAX3107_BRGCFG_2XMODE_BIT (1 << 4) /* Double baud rate */ +#define MAX3107_BRGCFG_4XMODE_BIT (1 << 5) /* Quadruple baud rate */ +#define MAX3107_BRGCFG_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_BRGCFG_UNDEF7_BIT (1 << 7) /* Undefined/not used */ + +/* Clock source register bits */ +#define MAX3107_CLKSRC_INTOSC_BIT (1 << 0) /* Internal osc enable */ +#define MAX3107_CLKSRC_CRYST_BIT (1 << 1) /* Crystal osc enable */ +#define MAX3107_CLKSRC_PLL_BIT (1 << 2) /* PLL enable */ +#define MAX3107_CLKSRC_PLLBYP_BIT (1 << 3) /* PLL bypass */ +#define MAX3107_CLKSRC_EXTCLK_BIT (1 << 4) /* External clock enable */ +#define MAX3107_CLKSRC_UNDEF5_BIT (1 << 5) /* Undefined/not used */ +#define MAX3107_CLKSRC_UNDEF6_BIT (1 << 6) /* Undefined/not used */ +#define MAX3107_CLKSRC_CLK2RTS_BIT (1 << 7) /* Baud clk to RTS pin */ + + +/* HW definitions */ +#define MAX3107_RX_FIFO_SIZE 128 +#define MAX3107_TX_FIFO_SIZE 128 +#define MAX3107_REVID1 0x00a0 +#define MAX3107_REVID2 0x00a1 + + +/* Baud rate generator configuration values for external clock 13MHz */ +#define MAX3107_BRG13_B300 (0x0A9400 | 0x05) +#define MAX3107_BRG13_B600 (0x054A00 | 0x03) +#define MAX3107_BRG13_B1200 (0x02A500 | 0x01) +#define MAX3107_BRG13_B2400 (0x015200 | 0x09) +#define MAX3107_BRG13_B4800 (0x00A900 | 0x04) +#define MAX3107_BRG13_B9600 (0x005400 | 0x0A) +#define MAX3107_BRG13_B19200 (0x002A00 | 0x05) +#define MAX3107_BRG13_B38400 (0x001500 | 0x03) +#define MAX3107_BRG13_B57600 (0x000E00 | 0x02) +#define MAX3107_BRG13_B115200 (0x000700 | 0x01) +#define MAX3107_BRG13_B230400 (0x000300 | 0x08) +#define MAX3107_BRG13_B460800 (0x000100 | 0x0c) +#define MAX3107_BRG13_B921600 (0x000100 | 0x1c) + +/* Baud rate generator configuration values for external clock 26MHz */ +#define MAX3107_BRG26_B300 (0x152800 | 0x0A) +#define MAX3107_BRG26_B600 (0x0A9400 | 0x05) +#define MAX3107_BRG26_B1200 (0x054A00 | 0x03) +#define MAX3107_BRG26_B2400 (0x02A500 | 0x01) +#define MAX3107_BRG26_B4800 (0x015200 | 0x09) +#define MAX3107_BRG26_B9600 (0x00A900 | 0x04) +#define MAX3107_BRG26_B19200 (0x005400 | 0x0A) +#define MAX3107_BRG26_B38400 (0x002A00 | 0x05) +#define MAX3107_BRG26_B57600 (0x001C00 | 0x03) +#define MAX3107_BRG26_B115200 (0x000E00 | 0x02) +#define MAX3107_BRG26_B230400 (0x000700 | 0x01) +#define MAX3107_BRG26_B460800 (0x000300 | 0x08) +#define MAX3107_BRG26_B921600 (0x000100 | 0x0C) + +/* Baud rate generator configuration values for internal clock */ +#define MAX3107_BRG13_IB300 (0x008000 | 0x00) +#define MAX3107_BRG13_IB600 (0x004000 | 0x00) +#define MAX3107_BRG13_IB1200 (0x002000 | 0x00) +#define MAX3107_BRG13_IB2400 (0x001000 | 0x00) +#define MAX3107_BRG13_IB4800 (0x000800 | 0x00) +#define MAX3107_BRG13_IB9600 (0x000400 | 0x00) +#define MAX3107_BRG13_IB19200 (0x000200 | 0x00) +#define MAX3107_BRG13_IB38400 (0x000100 | 0x00) +#define MAX3107_BRG13_IB57600 (0x000000 | 0x0B) +#define MAX3107_BRG13_IB115200 (0x000000 | 0x05) +#define MAX3107_BRG13_IB230400 (0x000000 | 0x03) +#define MAX3107_BRG13_IB460800 (0x000000 | 0x00) +#define MAX3107_BRG13_IB921600 (0x000000 | 0x00) + + +struct baud_table { + int baud; + u32 new_brg; +}; + +struct max3107_port { + /* UART port structure */ + struct uart_port port; + + /* SPI device structure */ + struct spi_device *spi; + +#if defined(CONFIG_GPIOLIB) + /* GPIO chip stucture */ + struct gpio_chip chip; +#endif + + /* Workqueue that does all the magic */ + struct workqueue_struct *workqueue; + struct work_struct work; + + /* Lock for shared data */ + spinlock_t data_lock; + + /* Device configuration */ + int ext_clk; /* 1 if external clock used */ + int loopback; /* Current loopback mode state */ + int baud; /* Current baud rate */ + + /* State flags */ + int suspended; /* Indicates suspend mode */ + int tx_fifo_empty; /* Flag for TX FIFO state */ + int rx_enabled; /* Flag for receiver state */ + int tx_enabled; /* Flag for transmitter state */ + + u16 irqen_reg; /* Current IRQ enable register value */ + /* Shared data */ + u16 mode1_reg; /* Current mode1 register value*/ + int mode1_commit; /* Flag for setting new mode1 register value */ + u16 lcr_reg; /* Current LCR register value */ + int lcr_commit; /* Flag for setting new LCR register value */ + u32 brg_cfg; /* Current Baud rate generator config */ + int brg_commit; /* Flag for setting new baud rate generator + * config + */ + struct baud_table *baud_tbl; + int handle_irq; /* Indicates that IRQ should be handled */ + + /* Rx buffer and str*/ + u16 *rxbuf; + u8 *rxstr; + /* Tx buffer*/ + u16 *txbuf; + + struct max3107_plat *pdata; /* Platform data */ +}; + +/* Platform data structure */ +struct max3107_plat { + /* Loopback mode enable */ + int loopback; + /* External clock enable */ + int ext_clk; + /* Called during the register initialisation */ + void (*init)(struct max3107_port *s); + /* Called when the port is found and configured */ + int (*configure)(struct max3107_port *s); + /* HW suspend function */ + void (*hw_suspend) (struct max3107_port *s, int suspend); + /* Polling mode enable */ + int polled_mode; + /* Polling period if polling mode enabled */ + int poll_time; +}; + +extern int max3107_rw(struct max3107_port *s, u8 *tx, u8 *rx, int len); +extern void max3107_hw_susp(struct max3107_port *s, int suspend); +extern int max3107_probe(struct spi_device *spi, struct max3107_plat *pdata); +extern int max3107_remove(struct spi_device *spi); +extern int max3107_suspend(struct spi_device *spi, pm_message_t state); +extern int max3107_resume(struct spi_device *spi); + +#endif /* _LINUX_SERIAL_MAX3107_H */ diff --git a/drivers/serial/mcf.c b/drivers/serial/mcf.c index b5aaef965f2..3394b7cc172 100644 --- a/drivers/serial/mcf.c +++ b/drivers/serial/mcf.c @@ -70,16 +70,14 @@ static unsigned int mcf_tx_empty(struct uart_port *port) static unsigned int mcf_get_mctrl(struct uart_port *port) { struct mcf_uart *pp = container_of(port, struct mcf_uart, port); - unsigned long flags; unsigned int sigs; - spin_lock_irqsave(&port->lock, flags); sigs = (readb(port->membase + MCFUART_UIPR) & MCFUART_UIPR_CTS) ? 0 : TIOCM_CTS; sigs |= (pp->sigs & TIOCM_RTS); sigs |= (mcf_getppdcd(port->line) ? TIOCM_CD : 0); sigs |= (mcf_getppdtr(port->line) ? TIOCM_DTR : 0); - spin_unlock_irqrestore(&port->lock, flags); + return sigs; } @@ -88,16 +86,13 @@ static unsigned int mcf_get_mctrl(struct uart_port *port) static void mcf_set_mctrl(struct uart_port *port, unsigned int sigs) { struct mcf_uart *pp = container_of(port, struct mcf_uart, port); - unsigned long flags; - spin_lock_irqsave(&port->lock, flags); pp->sigs = sigs; mcf_setppdtr(port->line, (sigs & TIOCM_DTR)); if (sigs & TIOCM_RTS) writeb(MCFUART_UOP_RTS, port->membase + MCFUART_UOP1); else writeb(MCFUART_UOP_RTS, port->membase + MCFUART_UOP0); - spin_unlock_irqrestore(&port->lock, flags); } /****************************************************************************/ @@ -105,12 +100,9 @@ static void mcf_set_mctrl(struct uart_port *port, unsigned int sigs) static void mcf_start_tx(struct uart_port *port) { struct mcf_uart *pp = container_of(port, struct mcf_uart, port); - unsigned long flags; - spin_lock_irqsave(&port->lock, flags); pp->imr |= MCFUART_UIR_TXREADY; writeb(pp->imr, port->membase + MCFUART_UIMR); - spin_unlock_irqrestore(&port->lock, flags); } /****************************************************************************/ @@ -118,12 +110,9 @@ static void mcf_start_tx(struct uart_port *port) static void mcf_stop_tx(struct uart_port *port) { struct mcf_uart *pp = container_of(port, struct mcf_uart, port); - unsigned long flags; - spin_lock_irqsave(&port->lock, flags); pp->imr &= ~MCFUART_UIR_TXREADY; writeb(pp->imr, port->membase + MCFUART_UIMR); - spin_unlock_irqrestore(&port->lock, flags); } /****************************************************************************/ @@ -131,12 +120,9 @@ static void mcf_stop_tx(struct uart_port *port) static void mcf_stop_rx(struct uart_port *port) { struct mcf_uart *pp = container_of(port, struct mcf_uart, port); - unsigned long flags; - spin_lock_irqsave(&port->lock, flags); pp->imr &= ~MCFUART_UIR_RXREADY; writeb(pp->imr, port->membase + MCFUART_UIMR); - spin_unlock_irqrestore(&port->lock, flags); } /****************************************************************************/ @@ -366,13 +352,22 @@ static irqreturn_t mcf_interrupt(int irq, void *data) struct uart_port *port = data; struct mcf_uart *pp = container_of(port, struct mcf_uart, port); unsigned int isr; + irqreturn_t ret = IRQ_NONE; isr = readb(port->membase + MCFUART_UISR) & pp->imr; - if (isr & MCFUART_UIR_RXREADY) + + spin_lock(&port->lock); + if (isr & MCFUART_UIR_RXREADY) { mcf_rx_chars(pp); - if (isr & MCFUART_UIR_TXREADY) + ret = IRQ_HANDLED; + } + if (isr & MCFUART_UIR_TXREADY) { mcf_tx_chars(pp); - return IRQ_HANDLED; + ret = IRQ_HANDLED; + } + spin_unlock(&port->lock); + + return ret; } /****************************************************************************/ diff --git a/drivers/serial/mfd.c b/drivers/serial/mfd.c new file mode 100644 index 00000000000..bc9af503907 --- /dev/null +++ b/drivers/serial/mfd.c @@ -0,0 +1,1498 @@ +/* + * mfd.c: driver for High Speed UART device of Intel Medfield platform + * + * Refer pxa.c, 8250.c and some other drivers in drivers/serial/ + * + * (C) Copyright 2010 Intel Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; version 2 + * of the License. + */ + +/* Notes: + * 1. DMA channel allocation: 0/1 channel are assigned to port 0, + * 2/3 chan to port 1, 4/5 chan to port 3. Even number chans + * are used for RX, odd chans for TX + * + * 2. In A0 stepping, UART will not support TX half empty flag + * + * 3. The RI/DSR/DCD/DTR are not pinned out, DCD & DSR are always + * asserted, only when the HW is reset the DDCD and DDSR will + * be triggered + */ + +#include <linux/module.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/serial_reg.h> +#include <linux/circ_buf.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial_mfd.h> +#include <linux/dma-mapping.h> +#include <linux/pci.h> +#include <linux/io.h> +#include <linux/debugfs.h> + +#define MFD_HSU_A0_STEPPING 1 + +#define HSU_DMA_BUF_SIZE 2048 + +#define chan_readl(chan, offset) readl(chan->reg + offset) +#define chan_writel(chan, offset, val) writel(val, chan->reg + offset) + +#define mfd_readl(obj, offset) readl(obj->reg + offset) +#define mfd_writel(obj, offset, val) writel(val, obj->reg + offset) + +#define HSU_DMA_TIMEOUT_CHECK_FREQ (HZ/10) + +struct hsu_dma_buffer { + u8 *buf; + dma_addr_t dma_addr; + u32 dma_size; + u32 ofs; +}; + +struct hsu_dma_chan { + u32 id; + enum dma_data_direction dirt; + struct uart_hsu_port *uport; + void __iomem *reg; + struct timer_list rx_timer; /* only needed by RX channel */ +}; + +struct uart_hsu_port { + struct uart_port port; + unsigned char ier; + unsigned char lcr; + unsigned char mcr; + unsigned int lsr_break_flag; + char name[12]; + int index; + struct device *dev; + + struct hsu_dma_chan *txc; + struct hsu_dma_chan *rxc; + struct hsu_dma_buffer txbuf; + struct hsu_dma_buffer rxbuf; + int use_dma; /* flag for DMA/PIO */ + int running; + int dma_tx_on; +}; + +/* Top level data structure of HSU */ +struct hsu_port { + void __iomem *reg; + unsigned long paddr; + unsigned long iolen; + u32 irq; + + struct uart_hsu_port port[3]; + struct hsu_dma_chan chans[10]; + + struct dentry *debugfs; +}; + +static inline unsigned int serial_in(struct uart_hsu_port *up, int offset) +{ + unsigned int val; + + if (offset > UART_MSR) { + offset <<= 2; + val = readl(up->port.membase + offset); + } else + val = (unsigned int)readb(up->port.membase + offset); + + return val; +} + +static inline void serial_out(struct uart_hsu_port *up, int offset, int value) +{ + if (offset > UART_MSR) { + offset <<= 2; + writel(value, up->port.membase + offset); + } else { + unsigned char val = value & 0xff; + writeb(val, up->port.membase + offset); + } +} + +#ifdef CONFIG_DEBUG_FS + +#define HSU_REGS_BUFSIZE 1024 + +static int hsu_show_regs_open(struct inode *inode, struct file *file) +{ + file->private_data = inode->i_private; + return 0; +} + +static ssize_t port_show_regs(struct file *file, char __user *user_buf, + size_t count, loff_t *ppos) +{ + struct uart_hsu_port *up = file->private_data; + char *buf; + u32 len = 0; + ssize_t ret; + + buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL); + if (!buf) + return 0; + + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "MFD HSU port[%d] regs:\n", up->index); + + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "=================================\n"); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "IER: \t\t0x%08x\n", serial_in(up, UART_IER)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "IIR: \t\t0x%08x\n", serial_in(up, UART_IIR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "LCR: \t\t0x%08x\n", serial_in(up, UART_LCR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "MCR: \t\t0x%08x\n", serial_in(up, UART_MCR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "LSR: \t\t0x%08x\n", serial_in(up, UART_LSR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "MSR: \t\t0x%08x\n", serial_in(up, UART_MSR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "FOR: \t\t0x%08x\n", serial_in(up, UART_FOR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "PS: \t\t0x%08x\n", serial_in(up, UART_PS)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "MUL: \t\t0x%08x\n", serial_in(up, UART_MUL)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "DIV: \t\t0x%08x\n", serial_in(up, UART_DIV)); + + ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); + kfree(buf); + return ret; +} + +static ssize_t dma_show_regs(struct file *file, char __user *user_buf, + size_t count, loff_t *ppos) +{ + struct hsu_dma_chan *chan = file->private_data; + char *buf; + u32 len = 0; + ssize_t ret; + + buf = kzalloc(HSU_REGS_BUFSIZE, GFP_KERNEL); + if (!buf) + return 0; + + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "MFD HSU DMA channel [%d] regs:\n", chan->id); + + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "=================================\n"); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "CR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_CR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "DCR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_DCR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "BSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_BSR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "MOTSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_MOTSR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0SAR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D0TSR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1SAR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D1TSR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2SAR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D2TSR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0SAR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3SAR)); + len += snprintf(buf + len, HSU_REGS_BUFSIZE - len, + "D0TSR: \t\t0x%08x\n", chan_readl(chan, HSU_CH_D3TSR)); + + ret = simple_read_from_buffer(user_buf, count, ppos, buf, len); + kfree(buf); + return ret; +} + +static const struct file_operations port_regs_ops = { + .owner = THIS_MODULE, + .open = hsu_show_regs_open, + .read = port_show_regs, +}; + +static const struct file_operations dma_regs_ops = { + .owner = THIS_MODULE, + .open = hsu_show_regs_open, + .read = dma_show_regs, +}; + +static int hsu_debugfs_init(struct hsu_port *hsu) +{ + int i; + char name[32]; + + hsu->debugfs = debugfs_create_dir("hsu", NULL); + if (!hsu->debugfs) + return -ENOMEM; + + for (i = 0; i < 3; i++) { + snprintf(name, sizeof(name), "port_%d_regs", i); + debugfs_create_file(name, S_IFREG | S_IRUGO, + hsu->debugfs, (void *)(&hsu->port[i]), &port_regs_ops); + } + + for (i = 0; i < 6; i++) { + snprintf(name, sizeof(name), "dma_chan_%d_regs", i); + debugfs_create_file(name, S_IFREG | S_IRUGO, + hsu->debugfs, (void *)&hsu->chans[i], &dma_regs_ops); + } + + return 0; +} + +static void hsu_debugfs_remove(struct hsu_port *hsu) +{ + if (hsu->debugfs) + debugfs_remove_recursive(hsu->debugfs); +} + +#else +static inline int hsu_debugfs_init(struct hsu_port *hsu) +{ + return 0; +} + +static inline void hsu_debugfs_remove(struct hsu_port *hsu) +{ +} +#endif /* CONFIG_DEBUG_FS */ + +static void serial_hsu_enable_ms(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + + up->ier |= UART_IER_MSI; + serial_out(up, UART_IER, up->ier); +} + +void hsu_dma_tx(struct uart_hsu_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + struct hsu_dma_buffer *dbuf = &up->txbuf; + int count; + + /* test_and_set_bit may be better, but anyway it's in lock protected mode */ + if (up->dma_tx_on) + return; + + /* Update the circ buf info */ + xmit->tail += dbuf->ofs; + xmit->tail &= UART_XMIT_SIZE - 1; + + up->port.icount.tx += dbuf->ofs; + dbuf->ofs = 0; + + /* Disable the channel */ + chan_writel(up->txc, HSU_CH_CR, 0x0); + + if (!uart_circ_empty(xmit) && !uart_tx_stopped(&up->port)) { + dma_sync_single_for_device(up->port.dev, + dbuf->dma_addr, + dbuf->dma_size, + DMA_TO_DEVICE); + + count = CIRC_CNT_TO_END(xmit->head, xmit->tail, UART_XMIT_SIZE); + dbuf->ofs = count; + + /* Reprogram the channel */ + chan_writel(up->txc, HSU_CH_D0SAR, dbuf->dma_addr + xmit->tail); + chan_writel(up->txc, HSU_CH_D0TSR, count); + + /* Reenable the channel */ + chan_writel(up->txc, HSU_CH_DCR, 0x1 + | (0x1 << 8) + | (0x1 << 16) + | (0x1 << 24)); + up->dma_tx_on = 1; + chan_writel(up->txc, HSU_CH_CR, 0x1); + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); +} + +/* The buffer is already cache coherent */ +void hsu_dma_start_rx_chan(struct hsu_dma_chan *rxc, struct hsu_dma_buffer *dbuf) +{ + dbuf->ofs = 0; + + chan_writel(rxc, HSU_CH_BSR, 32); + chan_writel(rxc, HSU_CH_MOTSR, 4); + + chan_writel(rxc, HSU_CH_D0SAR, dbuf->dma_addr); + chan_writel(rxc, HSU_CH_D0TSR, dbuf->dma_size); + chan_writel(rxc, HSU_CH_DCR, 0x1 | (0x1 << 8) + | (0x1 << 16) + | (0x1 << 24) /* timeout bit, see HSU Errata 1 */ + ); + chan_writel(rxc, HSU_CH_CR, 0x3); + + mod_timer(&rxc->rx_timer, jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ); +} + +/* Protected by spin_lock_irqsave(port->lock) */ +static void serial_hsu_start_tx(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + + if (up->use_dma) { + hsu_dma_tx(up); + } else if (!(up->ier & UART_IER_THRI)) { + up->ier |= UART_IER_THRI; + serial_out(up, UART_IER, up->ier); + } +} + +static void serial_hsu_stop_tx(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + struct hsu_dma_chan *txc = up->txc; + + if (up->use_dma) + chan_writel(txc, HSU_CH_CR, 0x0); + else if (up->ier & UART_IER_THRI) { + up->ier &= ~UART_IER_THRI; + serial_out(up, UART_IER, up->ier); + } +} + +/* This is always called in spinlock protected mode, so + * modify timeout timer is safe here */ +void hsu_dma_rx(struct uart_hsu_port *up, u32 int_sts) +{ + struct hsu_dma_buffer *dbuf = &up->rxbuf; + struct hsu_dma_chan *chan = up->rxc; + struct uart_port *port = &up->port; + struct tty_struct *tty = port->state->port.tty; + int count; + + if (!tty) + return; + + /* + * First need to know how many is already transferred, + * then check if its a timeout DMA irq, and return + * the trail bytes out, push them up and reenable the + * channel + */ + + /* Timeout IRQ, need wait some time, see Errata 2 */ + if (int_sts & 0xf00) + udelay(2); + + /* Stop the channel */ + chan_writel(chan, HSU_CH_CR, 0x0); + + count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr; + if (!count) { + /* Restart the channel before we leave */ + chan_writel(chan, HSU_CH_CR, 0x3); + return; + } + del_timer(&chan->rx_timer); + + dma_sync_single_for_cpu(port->dev, dbuf->dma_addr, + dbuf->dma_size, DMA_FROM_DEVICE); + + /* + * Head will only wrap around when we recycle + * the DMA buffer, and when that happens, we + * explicitly set tail to 0. So head will + * always be greater than tail. + */ + tty_insert_flip_string(tty, dbuf->buf, count); + port->icount.rx += count; + + dma_sync_single_for_device(up->port.dev, dbuf->dma_addr, + dbuf->dma_size, DMA_FROM_DEVICE); + + /* Reprogram the channel */ + chan_writel(chan, HSU_CH_D0SAR, dbuf->dma_addr); + chan_writel(chan, HSU_CH_D0TSR, dbuf->dma_size); + chan_writel(chan, HSU_CH_DCR, 0x1 + | (0x1 << 8) + | (0x1 << 16) + | (0x1 << 24) /* timeout bit, see HSU Errata 1 */ + ); + tty_flip_buffer_push(tty); + + chan_writel(chan, HSU_CH_CR, 0x3); + chan->rx_timer.expires = jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ; + add_timer(&chan->rx_timer); + +} + +static void serial_hsu_stop_rx(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + struct hsu_dma_chan *chan = up->rxc; + + if (up->use_dma) + chan_writel(chan, HSU_CH_CR, 0x2); + else { + up->ier &= ~UART_IER_RLSI; + up->port.read_status_mask &= ~UART_LSR_DR; + serial_out(up, UART_IER, up->ier); + } +} + +static inline void receive_chars(struct uart_hsu_port *up, int *status) +{ + struct tty_struct *tty = up->port.state->port.tty; + unsigned int ch, flag; + unsigned int max_count = 256; + + if (!tty) + return; + + do { + ch = serial_in(up, UART_RX); + flag = TTY_NORMAL; + up->port.icount.rx++; + + if (unlikely(*status & (UART_LSR_BI | UART_LSR_PE | + UART_LSR_FE | UART_LSR_OE))) { + + dev_warn(up->dev, "We really rush into ERR/BI case" + "status = 0x%02x", *status); + /* For statistics only */ + if (*status & UART_LSR_BI) { + *status &= ~(UART_LSR_FE | UART_LSR_PE); + up->port.icount.brk++; + /* + * We do the SysRQ and SAK checking + * here because otherwise the break + * may get masked by ignore_status_mask + * or read_status_mask. + */ + if (uart_handle_break(&up->port)) + goto ignore_char; + } else if (*status & UART_LSR_PE) + up->port.icount.parity++; + else if (*status & UART_LSR_FE) + up->port.icount.frame++; + if (*status & UART_LSR_OE) + up->port.icount.overrun++; + + /* Mask off conditions which should be ignored. */ + *status &= up->port.read_status_mask; + +#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE + if (up->port.cons && + up->port.cons->index == up->port.line) { + /* Recover the break flag from console xmit */ + *status |= up->lsr_break_flag; + up->lsr_break_flag = 0; + } +#endif + if (*status & UART_LSR_BI) { + flag = TTY_BREAK; + } else if (*status & UART_LSR_PE) + flag = TTY_PARITY; + else if (*status & UART_LSR_FE) + flag = TTY_FRAME; + } + + if (uart_handle_sysrq_char(&up->port, ch)) + goto ignore_char; + + uart_insert_char(&up->port, *status, UART_LSR_OE, ch, flag); + ignore_char: + *status = serial_in(up, UART_LSR); + } while ((*status & UART_LSR_DR) && max_count--); + tty_flip_buffer_push(tty); +} + +static void transmit_chars(struct uart_hsu_port *up) +{ + struct circ_buf *xmit = &up->port.state->xmit; + int count; + + if (up->port.x_char) { + serial_out(up, UART_TX, up->port.x_char); + up->port.icount.tx++; + up->port.x_char = 0; + return; + } + if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) { + serial_hsu_stop_tx(&up->port); + return; + } + +#ifndef MFD_HSU_A0_STEPPING + count = up->port.fifosize / 2; +#else + /* + * A0 only supports fully empty IRQ, and the first char written + * into it won't clear the EMPT bit, so we may need be cautious + * by useing a shorter buffer + */ + count = up->port.fifosize - 4; +#endif + do { + serial_out(up, UART_TX, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + + up->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } while (--count > 0); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&up->port); + + if (uart_circ_empty(xmit)) + serial_hsu_stop_tx(&up->port); +} + +static inline void check_modem_status(struct uart_hsu_port *up) +{ + int status; + + status = serial_in(up, UART_MSR); + + if ((status & UART_MSR_ANY_DELTA) == 0) + return; + + if (status & UART_MSR_TERI) + up->port.icount.rng++; + if (status & UART_MSR_DDSR) + up->port.icount.dsr++; + /* We may only get DDCD when HW init and reset */ + if (status & UART_MSR_DDCD) + uart_handle_dcd_change(&up->port, status & UART_MSR_DCD); + /* Will start/stop_tx accordingly */ + if (status & UART_MSR_DCTS) + uart_handle_cts_change(&up->port, status & UART_MSR_CTS); + + wake_up_interruptible(&up->port.state->port.delta_msr_wait); +} + +/* + * This handles the interrupt from one port. + */ +static irqreturn_t port_irq(int irq, void *dev_id) +{ + struct uart_hsu_port *up = dev_id; + unsigned int iir, lsr; + unsigned long flags; + + if (unlikely(!up->running)) + return IRQ_NONE; + + spin_lock_irqsave(&up->port.lock, flags); + if (up->use_dma) { + lsr = serial_in(up, UART_LSR); + if (unlikely(lsr & (UART_LSR_BI | UART_LSR_PE | + UART_LSR_FE | UART_LSR_OE))) + dev_warn(up->dev, + "Got lsr irq while using DMA, lsr = 0x%2x\n", + lsr); + check_modem_status(up); + spin_unlock_irqrestore(&up->port.lock, flags); + return IRQ_HANDLED; + } + + iir = serial_in(up, UART_IIR); + if (iir & UART_IIR_NO_INT) { + spin_unlock_irqrestore(&up->port.lock, flags); + return IRQ_NONE; + } + + lsr = serial_in(up, UART_LSR); + if (lsr & UART_LSR_DR) + receive_chars(up, &lsr); + check_modem_status(up); + + /* lsr will be renewed during the receive_chars */ + if (lsr & UART_LSR_THRE) + transmit_chars(up); + + spin_unlock_irqrestore(&up->port.lock, flags); + return IRQ_HANDLED; +} + +static inline void dma_chan_irq(struct hsu_dma_chan *chan) +{ + struct uart_hsu_port *up = chan->uport; + unsigned long flags; + u32 int_sts; + + spin_lock_irqsave(&up->port.lock, flags); + + if (!up->use_dma || !up->running) + goto exit; + + /* + * No matter what situation, need read clear the IRQ status + * There is a bug, see Errata 5, HSD 2900918 + */ + int_sts = chan_readl(chan, HSU_CH_SR); + + /* Rx channel */ + if (chan->dirt == DMA_FROM_DEVICE) + hsu_dma_rx(up, int_sts); + + /* Tx channel */ + if (chan->dirt == DMA_TO_DEVICE) { + chan_writel(chan, HSU_CH_CR, 0x0); + up->dma_tx_on = 0; + hsu_dma_tx(up); + } + +exit: + spin_unlock_irqrestore(&up->port.lock, flags); + return; +} + +static irqreturn_t dma_irq(int irq, void *dev_id) +{ + struct hsu_port *hsu = dev_id; + u32 int_sts, i; + + int_sts = mfd_readl(hsu, HSU_GBL_DMAISR); + + /* Currently we only have 6 channels may be used */ + for (i = 0; i < 6; i++) { + if (int_sts & 0x1) + dma_chan_irq(&hsu->chans[i]); + int_sts >>= 1; + } + + return IRQ_HANDLED; +} + +static unsigned int serial_hsu_tx_empty(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + unsigned long flags; + unsigned int ret; + + spin_lock_irqsave(&up->port.lock, flags); + ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0; + spin_unlock_irqrestore(&up->port.lock, flags); + + return ret; +} + +static unsigned int serial_hsu_get_mctrl(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + unsigned char status; + unsigned int ret; + + status = serial_in(up, UART_MSR); + + ret = 0; + if (status & UART_MSR_DCD) + ret |= TIOCM_CAR; + if (status & UART_MSR_RI) + ret |= TIOCM_RNG; + if (status & UART_MSR_DSR) + ret |= TIOCM_DSR; + if (status & UART_MSR_CTS) + ret |= TIOCM_CTS; + return ret; +} + +static void serial_hsu_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + unsigned char mcr = 0; + + if (mctrl & TIOCM_RTS) + mcr |= UART_MCR_RTS; + if (mctrl & TIOCM_DTR) + mcr |= UART_MCR_DTR; + if (mctrl & TIOCM_OUT1) + mcr |= UART_MCR_OUT1; + if (mctrl & TIOCM_OUT2) + mcr |= UART_MCR_OUT2; + if (mctrl & TIOCM_LOOP) + mcr |= UART_MCR_LOOP; + + mcr |= up->mcr; + + serial_out(up, UART_MCR, mcr); +} + +static void serial_hsu_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + if (break_state == -1) + up->lcr |= UART_LCR_SBC; + else + up->lcr &= ~UART_LCR_SBC; + serial_out(up, UART_LCR, up->lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +/* + * What special to do: + * 1. chose the 64B fifo mode + * 2. make sure not to select half empty mode for A0 stepping + * 3. start dma or pio depends on configuration + * 4. we only allocate dma memory when needed + */ +static int serial_hsu_startup(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + unsigned long flags; + + /* + * Clear the FIFO buffers and disable them. + * (they will be reenabled in set_termios()) + */ + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT); + serial_out(up, UART_FCR, 0); + + /* Clear the interrupt registers. */ + (void) serial_in(up, UART_LSR); + (void) serial_in(up, UART_RX); + (void) serial_in(up, UART_IIR); + (void) serial_in(up, UART_MSR); + + /* Now, initialize the UART, default is 8n1 */ + serial_out(up, UART_LCR, UART_LCR_WLEN8); + + spin_lock_irqsave(&up->port.lock, flags); + + up->port.mctrl |= TIOCM_OUT2; + serial_hsu_set_mctrl(&up->port, up->port.mctrl); + + /* + * Finally, enable interrupts. Note: Modem status interrupts + * are set via set_termios(), which will be occurring imminently + * anyway, so we don't enable them here. + */ + if (!up->use_dma) + up->ier = UART_IER_RLSI | UART_IER_RDI | UART_IER_RTOIE; + else + up->ier = 0; + serial_out(up, UART_IER, up->ier); + + spin_unlock_irqrestore(&up->port.lock, flags); + + /* DMA init */ + if (up->use_dma) { + struct hsu_dma_buffer *dbuf; + struct circ_buf *xmit = &port->state->xmit; + + up->dma_tx_on = 0; + + /* First allocate the RX buffer */ + dbuf = &up->rxbuf; + dbuf->buf = kzalloc(HSU_DMA_BUF_SIZE, GFP_KERNEL); + if (!dbuf->buf) { + up->use_dma = 0; + goto exit; + } + dbuf->dma_addr = dma_map_single(port->dev, + dbuf->buf, + HSU_DMA_BUF_SIZE, + DMA_FROM_DEVICE); + dbuf->dma_size = HSU_DMA_BUF_SIZE; + + /* Start the RX channel right now */ + hsu_dma_start_rx_chan(up->rxc, dbuf); + + /* Next init the TX DMA */ + dbuf = &up->txbuf; + dbuf->buf = xmit->buf; + dbuf->dma_addr = dma_map_single(port->dev, + dbuf->buf, + UART_XMIT_SIZE, + DMA_TO_DEVICE); + dbuf->dma_size = UART_XMIT_SIZE; + + /* This should not be changed all around */ + chan_writel(up->txc, HSU_CH_BSR, 32); + chan_writel(up->txc, HSU_CH_MOTSR, 4); + dbuf->ofs = 0; + } + +exit: + /* And clear the interrupt registers again for luck. */ + (void) serial_in(up, UART_LSR); + (void) serial_in(up, UART_RX); + (void) serial_in(up, UART_IIR); + (void) serial_in(up, UART_MSR); + + up->running = 1; + return 0; +} + +static void serial_hsu_shutdown(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + unsigned long flags; + + del_timer_sync(&up->rxc->rx_timer); + + /* Disable interrupts from this port */ + up->ier = 0; + serial_out(up, UART_IER, 0); + up->running = 0; + + spin_lock_irqsave(&up->port.lock, flags); + up->port.mctrl &= ~TIOCM_OUT2; + serial_hsu_set_mctrl(&up->port, up->port.mctrl); + spin_unlock_irqrestore(&up->port.lock, flags); + + /* Disable break condition and FIFOs */ + serial_out(up, UART_LCR, serial_in(up, UART_LCR) & ~UART_LCR_SBC); + serial_out(up, UART_FCR, UART_FCR_ENABLE_FIFO | + UART_FCR_CLEAR_RCVR | + UART_FCR_CLEAR_XMIT); + serial_out(up, UART_FCR, 0); +} + +static void +serial_hsu_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + struct tty_struct *tty = port->state->port.tty; + unsigned char cval, fcr = 0; + unsigned long flags; + unsigned int baud, quot; + u32 mul = 0x3600; + u32 ps = 0x10; + + switch (termios->c_cflag & CSIZE) { + case CS5: + cval = UART_LCR_WLEN5; + break; + case CS6: + cval = UART_LCR_WLEN6; + break; + case CS7: + cval = UART_LCR_WLEN7; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + break; + } + + /* CMSPAR isn't supported by this driver */ + if (tty) + tty->termios->c_cflag &= ~CMSPAR; + + if (termios->c_cflag & CSTOPB) + cval |= UART_LCR_STOP; + if (termios->c_cflag & PARENB) + cval |= UART_LCR_PARITY; + if (!(termios->c_cflag & PARODD)) + cval |= UART_LCR_EPAR; + + /* + * For those basic low baud rate we can get the direct + * scalar from 2746800, like 115200 = 2746800/24, for those + * higher baud rate, we have to handle them case by case, + * but DIV reg is never touched as its default value 0x3d09 + */ + baud = uart_get_baud_rate(port, termios, old, 0, 4000000); + quot = uart_get_divisor(port, baud); + + switch (baud) { + case 3500000: + mul = 0x3345; + ps = 0xC; + quot = 1; + break; + case 2500000: + mul = 0x2710; + ps = 0x10; + quot = 1; + break; + case 18432000: + mul = 0x2400; + ps = 0x10; + quot = 1; + break; + case 1500000: + mul = 0x1D4C; + ps = 0xc; + quot = 1; + break; + default: + ; + } + + if ((up->port.uartclk / quot) < (2400 * 16)) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_1B; + else if ((up->port.uartclk / quot) < (230400 * 16)) + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_16B; + else + fcr = UART_FCR_ENABLE_FIFO | UART_FCR_HSU_64_32B; + + fcr |= UART_FCR_HSU_64B_FIFO; +#ifdef MFD_HSU_A0_STEPPING + /* A0 doesn't support half empty IRQ */ + fcr |= UART_FCR_FULL_EMPT_TXI; +#endif + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + /* Update the per-port timeout */ + uart_update_timeout(port, termios->c_cflag, baud); + + up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= UART_LSR_BI; + + /* Characters to ignore */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= UART_LSR_BI; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= UART_LSR_OE; + } + + /* Ignore all characters if CREAD is not set */ + if ((termios->c_cflag & CREAD) == 0) + up->port.ignore_status_mask |= UART_LSR_DR; + + /* + * CTS flow control flag and modem status interrupts, disable + * MSI by default + */ + up->ier &= ~UART_IER_MSI; + if (UART_ENABLE_MS(&up->port, termios->c_cflag)) + up->ier |= UART_IER_MSI; + + serial_out(up, UART_IER, up->ier); + + if (termios->c_cflag & CRTSCTS) + up->mcr |= UART_MCR_AFE | UART_MCR_RTS; + else + up->mcr &= ~UART_MCR_AFE; + + serial_out(up, UART_LCR, cval | UART_LCR_DLAB); /* set DLAB */ + serial_out(up, UART_DLL, quot & 0xff); /* LS of divisor */ + serial_out(up, UART_DLM, quot >> 8); /* MS of divisor */ + serial_out(up, UART_LCR, cval); /* reset DLAB */ + serial_out(up, UART_MUL, mul); /* set MUL */ + serial_out(up, UART_PS, ps); /* set PS */ + up->lcr = cval; /* Save LCR */ + serial_hsu_set_mctrl(&up->port, up->port.mctrl); + serial_out(up, UART_FCR, fcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void +serial_hsu_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ +} + +static void serial_hsu_release_port(struct uart_port *port) +{ +} + +static int serial_hsu_request_port(struct uart_port *port) +{ + return 0; +} + +static void serial_hsu_config_port(struct uart_port *port, int flags) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + up->port.type = PORT_MFD; +} + +static int +serial_hsu_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + /* We don't want the core code to modify any port params */ + return -EINVAL; +} + +static const char * +serial_hsu_type(struct uart_port *port) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + return up->name; +} + +/* Mainly for uart console use */ +static struct uart_hsu_port *serial_hsu_ports[3]; +static struct uart_driver serial_hsu_reg; + +#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE + +#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE) + +/* Wait for transmitter & holding register to empty */ +static inline void wait_for_xmitr(struct uart_hsu_port *up) +{ + unsigned int status, tmout = 1000; + + /* Wait up to 1ms for the character to be sent. */ + do { + status = serial_in(up, UART_LSR); + + if (status & UART_LSR_BI) + up->lsr_break_flag = UART_LSR_BI; + + if (--tmout == 0) + break; + udelay(1); + } while (!(status & BOTH_EMPTY)); + + /* Wait up to 1s for flow control if necessary */ + if (up->port.flags & UPF_CONS_FLOW) { + tmout = 1000000; + while (--tmout && + ((serial_in(up, UART_MSR) & UART_MSR_CTS) == 0)) + udelay(1); + } +} + +static void serial_hsu_console_putchar(struct uart_port *port, int ch) +{ + struct uart_hsu_port *up = + container_of(port, struct uart_hsu_port, port); + + wait_for_xmitr(up); + serial_out(up, UART_TX, ch); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + * + * The console_lock must be held when we get here. + */ +static void +serial_hsu_console_write(struct console *co, const char *s, unsigned int count) +{ + struct uart_hsu_port *up = serial_hsu_ports[co->index]; + unsigned long flags; + unsigned int ier; + int locked = 1; + + local_irq_save(flags); + if (up->port.sysrq) + locked = 0; + else if (oops_in_progress) { + locked = spin_trylock(&up->port.lock); + } else + spin_lock(&up->port.lock); + + /* First save the IER then disable the interrupts */ + ier = serial_in(up, UART_IER); + serial_out(up, UART_IER, 0); + + uart_console_write(&up->port, s, count, serial_hsu_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore the IER + */ + wait_for_xmitr(up); + serial_out(up, UART_IER, ier); + + if (locked) + spin_unlock(&up->port.lock); + local_irq_restore(flags); +} + +static struct console serial_hsu_console; + +static int __init +serial_hsu_console_setup(struct console *co, char *options) +{ + struct uart_hsu_port *up; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + int ret; + + if (co->index == -1 || co->index >= serial_hsu_reg.nr) + co->index = 0; + up = serial_hsu_ports[co->index]; + if (!up) + return -ENODEV; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + ret = uart_set_options(&up->port, co, baud, parity, bits, flow); + + return ret; +} + +static struct console serial_hsu_console = { + .name = "ttyMFD", + .write = serial_hsu_console_write, + .device = uart_console_device, + .setup = serial_hsu_console_setup, + .flags = CON_PRINTBUFFER, + .index = 2, + .data = &serial_hsu_reg, +}; +#endif + +struct uart_ops serial_hsu_pops = { + .tx_empty = serial_hsu_tx_empty, + .set_mctrl = serial_hsu_set_mctrl, + .get_mctrl = serial_hsu_get_mctrl, + .stop_tx = serial_hsu_stop_tx, + .start_tx = serial_hsu_start_tx, + .stop_rx = serial_hsu_stop_rx, + .enable_ms = serial_hsu_enable_ms, + .break_ctl = serial_hsu_break_ctl, + .startup = serial_hsu_startup, + .shutdown = serial_hsu_shutdown, + .set_termios = serial_hsu_set_termios, + .pm = serial_hsu_pm, + .type = serial_hsu_type, + .release_port = serial_hsu_release_port, + .request_port = serial_hsu_request_port, + .config_port = serial_hsu_config_port, + .verify_port = serial_hsu_verify_port, +}; + +static struct uart_driver serial_hsu_reg = { + .owner = THIS_MODULE, + .driver_name = "MFD serial", + .dev_name = "ttyMFD", + .major = TTY_MAJOR, + .minor = 128, + .nr = 3, +}; + +#ifdef CONFIG_PM +static int serial_hsu_suspend(struct pci_dev *pdev, pm_message_t state) +{ + void *priv = pci_get_drvdata(pdev); + struct uart_hsu_port *up; + + /* Make sure this is not the internal dma controller */ + if (priv && (pdev->device != 0x081E)) { + up = priv; + uart_suspend_port(&serial_hsu_reg, &up->port); + } + + pci_save_state(pdev); + pci_set_power_state(pdev, pci_choose_state(pdev, state)); + return 0; +} + +static int serial_hsu_resume(struct pci_dev *pdev) +{ + void *priv = pci_get_drvdata(pdev); + struct uart_hsu_port *up; + int ret; + + pci_set_power_state(pdev, PCI_D0); + pci_restore_state(pdev); + + ret = pci_enable_device(pdev); + if (ret) + dev_warn(&pdev->dev, + "HSU: can't re-enable device, try to continue\n"); + + if (priv && (pdev->device != 0x081E)) { + up = priv; + uart_resume_port(&serial_hsu_reg, &up->port); + } + return 0; +} +#else +#define serial_hsu_suspend NULL +#define serial_hsu_resume NULL +#endif + +/* temp global pointer before we settle down on using one or four PCI dev */ +static struct hsu_port *phsu; + +static int serial_hsu_probe(struct pci_dev *pdev, + const struct pci_device_id *ent) +{ + struct uart_hsu_port *uport; + int index, ret; + + printk(KERN_INFO "HSU: found PCI Serial controller(ID: %04x:%04x)\n", + pdev->vendor, pdev->device); + + switch (pdev->device) { + case 0x081B: + index = 0; + break; + case 0x081C: + index = 1; + break; + case 0x081D: + index = 2; + break; + case 0x081E: + /* internal DMA controller */ + index = 3; + break; + default: + dev_err(&pdev->dev, "HSU: out of index!"); + return -ENODEV; + } + + ret = pci_enable_device(pdev); + if (ret) + return ret; + + if (index == 3) { + /* DMA controller */ + ret = request_irq(pdev->irq, dma_irq, 0, "hsu_dma", phsu); + if (ret) { + dev_err(&pdev->dev, "can not get IRQ\n"); + goto err_disable; + } + pci_set_drvdata(pdev, phsu); + } else { + /* UART port 0~2 */ + uport = &phsu->port[index]; + uport->port.irq = pdev->irq; + uport->port.dev = &pdev->dev; + uport->dev = &pdev->dev; + + ret = request_irq(pdev->irq, port_irq, 0, uport->name, uport); + if (ret) { + dev_err(&pdev->dev, "can not get IRQ\n"); + goto err_disable; + } + uart_add_one_port(&serial_hsu_reg, &uport->port); + +#ifdef CONFIG_SERIAL_MFD_HSU_CONSOLE + if (index == 2) { + register_console(&serial_hsu_console); + uport->port.cons = &serial_hsu_console; + } +#endif + pci_set_drvdata(pdev, uport); + } + + return 0; + +err_disable: + pci_disable_device(pdev); + return ret; +} + +static void hsu_dma_rx_timeout(unsigned long data) +{ + struct hsu_dma_chan *chan = (void *)data; + struct uart_hsu_port *up = chan->uport; + struct hsu_dma_buffer *dbuf = &up->rxbuf; + int count = 0; + unsigned long flags; + + spin_lock_irqsave(&up->port.lock, flags); + + count = chan_readl(chan, HSU_CH_D0SAR) - dbuf->dma_addr; + + if (!count) { + mod_timer(&chan->rx_timer, jiffies + HSU_DMA_TIMEOUT_CHECK_FREQ); + goto exit; + } + + hsu_dma_rx(up, 0); +exit: + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static void hsu_global_init(void) +{ + struct hsu_port *hsu; + struct uart_hsu_port *uport; + struct hsu_dma_chan *dchan; + int i, ret; + + hsu = kzalloc(sizeof(struct hsu_port), GFP_KERNEL); + if (!hsu) + return; + + /* Get basic io resource and map it */ + hsu->paddr = 0xffa28000; + hsu->iolen = 0x1000; + + if (!(request_mem_region(hsu->paddr, hsu->iolen, "HSU global"))) + pr_warning("HSU: error in request mem region\n"); + + hsu->reg = ioremap_nocache((unsigned long)hsu->paddr, hsu->iolen); + if (!hsu->reg) { + pr_err("HSU: error in ioremap\n"); + ret = -ENOMEM; + goto err_free_region; + } + + /* Initialise the 3 UART ports */ + uport = hsu->port; + for (i = 0; i < 3; i++) { + uport->port.type = PORT_MFD; + uport->port.iotype = UPIO_MEM; + uport->port.mapbase = (resource_size_t)hsu->paddr + + HSU_PORT_REG_OFFSET + + i * HSU_PORT_REG_LENGTH; + uport->port.membase = hsu->reg + HSU_PORT_REG_OFFSET + + i * HSU_PORT_REG_LENGTH; + + sprintf(uport->name, "hsu_port%d", i); + uport->port.fifosize = 64; + uport->port.ops = &serial_hsu_pops; + uport->port.line = i; + uport->port.flags = UPF_IOREMAP; + /* set the scalable maxim support rate to 2746800 bps */ + uport->port.uartclk = 115200 * 24 * 16; + + uport->running = 0; + uport->txc = &hsu->chans[i * 2]; + uport->rxc = &hsu->chans[i * 2 + 1]; + + serial_hsu_ports[i] = uport; + uport->index = i; + uport++; + } + + /* Initialise 6 dma channels */ + dchan = hsu->chans; + for (i = 0; i < 6; i++) { + dchan->id = i; + dchan->dirt = (i & 0x1) ? DMA_FROM_DEVICE : DMA_TO_DEVICE; + dchan->uport = &hsu->port[i/2]; + dchan->reg = hsu->reg + HSU_DMA_CHANS_REG_OFFSET + + i * HSU_DMA_CHANS_REG_LENGTH; + + /* Work around for RX */ + if (dchan->dirt == DMA_FROM_DEVICE) { + init_timer(&dchan->rx_timer); + dchan->rx_timer.function = hsu_dma_rx_timeout; + dchan->rx_timer.data = (unsigned long)dchan; + } + dchan++; + } + + phsu = hsu; + + hsu_debugfs_init(hsu); + return; + +err_free_region: + release_mem_region(hsu->paddr, hsu->iolen); + kfree(hsu); + return; +} + +static void serial_hsu_remove(struct pci_dev *pdev) +{ + struct hsu_port *hsu; + int i; + + hsu = pci_get_drvdata(pdev); + if (!hsu) + return; + + for (i = 0; i < 3; i++) + uart_remove_one_port(&serial_hsu_reg, &hsu->port[i].port); + + pci_set_drvdata(pdev, NULL); + free_irq(hsu->irq, hsu); + pci_disable_device(pdev); +} + +/* First 3 are UART ports, and the 4th is the DMA */ +static const struct pci_device_id pci_ids[] __devinitdata = { + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081B) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081C) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081D) }, + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, 0x081E) }, + {}, +}; + +static struct pci_driver hsu_pci_driver = { + .name = "HSU serial", + .id_table = pci_ids, + .probe = serial_hsu_probe, + .remove = __devexit_p(serial_hsu_remove), + .suspend = serial_hsu_suspend, + .resume = serial_hsu_resume, +}; + +static int __init hsu_pci_init(void) +{ + int ret; + + hsu_global_init(); + + ret = uart_register_driver(&serial_hsu_reg); + if (ret) + return ret; + + return pci_register_driver(&hsu_pci_driver); +} + +static void __exit hsu_pci_exit(void) +{ + pci_unregister_driver(&hsu_pci_driver); + uart_unregister_driver(&serial_hsu_reg); + + hsu_debugfs_remove(phsu); + + kfree(phsu); +} + +module_init(hsu_pci_init); +module_exit(hsu_pci_exit); + +MODULE_LICENSE("GPL v2"); +MODULE_ALIAS("platform:medfield-hsu"); diff --git a/drivers/serial/mpc52xx_uart.c b/drivers/serial/mpc52xx_uart.c index 84a35f69901..8dedb266f14 100644 --- a/drivers/serial/mpc52xx_uart.c +++ b/drivers/serial/mpc52xx_uart.c @@ -113,7 +113,9 @@ struct psc_ops { unsigned char (*read_char)(struct uart_port *port); void (*cw_disable_ints)(struct uart_port *port); void (*cw_restore_ints)(struct uart_port *port); - unsigned long (*getuartclk)(void *p); + unsigned int (*set_baudrate)(struct uart_port *port, + struct ktermios *new, + struct ktermios *old); int (*clock)(struct uart_port *port, int enable); int (*fifoc_init)(void); void (*fifoc_uninit)(void); @@ -121,6 +123,16 @@ struct psc_ops { irqreturn_t (*handle_irq)(struct uart_port *port); }; +/* setting the prescaler and divisor reg is common for all chips */ +static inline void mpc52xx_set_divisor(struct mpc52xx_psc __iomem *psc, + u16 prescaler, unsigned int divisor) +{ + /* select prescaler */ + out_be16(&psc->mpc52xx_psc_clock_select, prescaler); + out_8(&psc->ctur, divisor >> 8); + out_8(&psc->ctlr, divisor & 0xff); +} + #ifdef CONFIG_PPC_MPC52xx #define FIFO_52xx(port) ((struct mpc52xx_psc_fifo __iomem *)(PSC(port)+1)) static void mpc52xx_psc_fifo_init(struct uart_port *port) @@ -128,9 +140,6 @@ static void mpc52xx_psc_fifo_init(struct uart_port *port) struct mpc52xx_psc __iomem *psc = PSC(port); struct mpc52xx_psc_fifo __iomem *fifo = FIFO_52xx(port); - /* /32 prescaler */ - out_be16(&psc->mpc52xx_psc_clock_select, 0xdd00); - out_8(&fifo->rfcntl, 0x00); out_be16(&fifo->rfalarm, 0x1ff); out_8(&fifo->tfcntl, 0x07); @@ -219,15 +228,47 @@ static void mpc52xx_psc_cw_restore_ints(struct uart_port *port) out_be16(&PSC(port)->mpc52xx_psc_imr, port->read_status_mask); } -/* Search for bus-frequency property in this node or a parent */ -static unsigned long mpc52xx_getuartclk(void *p) +static unsigned int mpc5200_psc_set_baudrate(struct uart_port *port, + struct ktermios *new, + struct ktermios *old) { - /* - * 5200 UARTs have a / 32 prescaler - * but the generic serial code assumes 16 - * so return ipb freq / 2 - */ - return mpc5xxx_get_bus_frequency(p) / 2; + unsigned int baud; + unsigned int divisor; + + /* The 5200 has a fixed /32 prescaler, uartclk contains the ipb freq */ + baud = uart_get_baud_rate(port, new, old, + port->uartclk / (32 * 0xffff) + 1, + port->uartclk / 32); + divisor = (port->uartclk + 16 * baud) / (32 * baud); + + /* enable the /32 prescaler and set the divisor */ + mpc52xx_set_divisor(PSC(port), 0xdd00, divisor); + return baud; +} + +static unsigned int mpc5200b_psc_set_baudrate(struct uart_port *port, + struct ktermios *new, + struct ktermios *old) +{ + unsigned int baud; + unsigned int divisor; + u16 prescaler; + + /* The 5200B has a selectable /4 or /32 prescaler, uartclk contains the + * ipb freq */ + baud = uart_get_baud_rate(port, new, old, + port->uartclk / (32 * 0xffff) + 1, + port->uartclk / 4); + divisor = (port->uartclk + 2 * baud) / (4 * baud); + + /* select the proper prescaler and set the divisor */ + if (divisor > 0xffff) { + divisor = (divisor + 4) / 8; + prescaler = 0xdd00; /* /32 */ + } else + prescaler = 0xff00; /* /4 */ + mpc52xx_set_divisor(PSC(port), prescaler, divisor); + return baud; } static void mpc52xx_psc_get_irq(struct uart_port *port, struct device_node *np) @@ -258,7 +299,28 @@ static struct psc_ops mpc52xx_psc_ops = { .read_char = mpc52xx_psc_read_char, .cw_disable_ints = mpc52xx_psc_cw_disable_ints, .cw_restore_ints = mpc52xx_psc_cw_restore_ints, - .getuartclk = mpc52xx_getuartclk, + .set_baudrate = mpc5200_psc_set_baudrate, + .get_irq = mpc52xx_psc_get_irq, + .handle_irq = mpc52xx_psc_handle_irq, +}; + +static struct psc_ops mpc5200b_psc_ops = { + .fifo_init = mpc52xx_psc_fifo_init, + .raw_rx_rdy = mpc52xx_psc_raw_rx_rdy, + .raw_tx_rdy = mpc52xx_psc_raw_tx_rdy, + .rx_rdy = mpc52xx_psc_rx_rdy, + .tx_rdy = mpc52xx_psc_tx_rdy, + .tx_empty = mpc52xx_psc_tx_empty, + .stop_rx = mpc52xx_psc_stop_rx, + .start_tx = mpc52xx_psc_start_tx, + .stop_tx = mpc52xx_psc_stop_tx, + .rx_clr_irq = mpc52xx_psc_rx_clr_irq, + .tx_clr_irq = mpc52xx_psc_tx_clr_irq, + .write_char = mpc52xx_psc_write_char, + .read_char = mpc52xx_psc_read_char, + .cw_disable_ints = mpc52xx_psc_cw_disable_ints, + .cw_restore_ints = mpc52xx_psc_cw_restore_ints, + .set_baudrate = mpc5200b_psc_set_baudrate, .get_irq = mpc52xx_psc_get_irq, .handle_irq = mpc52xx_psc_handle_irq, }; @@ -392,9 +454,35 @@ static void mpc512x_psc_cw_restore_ints(struct uart_port *port) out_be32(&FIFO_512x(port)->rximr, port->read_status_mask & 0x7f); } -static unsigned long mpc512x_getuartclk(void *p) +static unsigned int mpc512x_psc_set_baudrate(struct uart_port *port, + struct ktermios *new, + struct ktermios *old) { - return mpc5xxx_get_bus_frequency(p); + unsigned int baud; + unsigned int divisor; + + /* + * The "MPC5121e Microcontroller Reference Manual, Rev. 3" says on + * pg. 30-10 that the chip supports a /32 and a /10 prescaler. + * Furthermore, it states that "After reset, the prescaler by 10 + * for the UART mode is selected", but the reset register value is + * 0x0000 which means a /32 prescaler. This is wrong. + * + * In reality using /32 prescaler doesn't work, as it is not supported! + * Use /16 or /10 prescaler, see "MPC5121e Hardware Design Guide", + * Chapter 4.1 PSC in UART Mode. + * Calculate with a /16 prescaler here. + */ + + /* uartclk contains the ips freq */ + baud = uart_get_baud_rate(port, new, old, + port->uartclk / (16 * 0xffff) + 1, + port->uartclk / 16); + divisor = (port->uartclk + 8 * baud) / (16 * baud); + + /* enable the /16 prescaler and set the divisor */ + mpc52xx_set_divisor(PSC(port), 0xdd00, divisor); + return baud; } /* Init PSC FIFO Controller */ @@ -498,7 +586,7 @@ static struct psc_ops mpc512x_psc_ops = { .read_char = mpc512x_psc_read_char, .cw_disable_ints = mpc512x_psc_cw_disable_ints, .cw_restore_ints = mpc512x_psc_cw_restore_ints, - .getuartclk = mpc512x_getuartclk, + .set_baudrate = mpc512x_psc_set_baudrate, .clock = mpc512x_psc_clock, .fifoc_init = mpc512x_psc_fifoc_init, .fifoc_uninit = mpc512x_psc_fifoc_uninit, @@ -666,8 +754,8 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new, struct mpc52xx_psc __iomem *psc = PSC(port); unsigned long flags; unsigned char mr1, mr2; - unsigned short ctr; - unsigned int j, baud, quot; + unsigned int j; + unsigned int baud; /* Prepare what we're gonna write */ mr1 = 0; @@ -704,16 +792,9 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new, mr2 |= MPC52xx_PSC_MODE_TXCTS; } - baud = uart_get_baud_rate(port, new, old, 0, port->uartclk/16); - quot = uart_get_divisor(port, baud); - ctr = quot & 0xffff; - /* Get the lock */ spin_lock_irqsave(&port->lock, flags); - /* Update the per-port timeout */ - uart_update_timeout(port, new->c_cflag, baud); - /* Do our best to flush TX & RX, so we don't lose anything */ /* But we don't wait indefinitely ! */ j = 5000000; /* Maximum wait */ @@ -737,8 +818,10 @@ mpc52xx_uart_set_termios(struct uart_port *port, struct ktermios *new, out_8(&psc->command, MPC52xx_PSC_SEL_MODE_REG_1); out_8(&psc->mode, mr1); out_8(&psc->mode, mr2); - out_8(&psc->ctur, ctr >> 8); - out_8(&psc->ctlr, ctr & 0xff); + baud = psc_ops->set_baudrate(port, new, old); + + /* Update the per-port timeout */ + uart_update_timeout(port, new->c_cflag, baud); if (UART_ENABLE_MS(port, new->c_cflag)) mpc52xx_uart_enable_ms(port); @@ -1118,7 +1201,7 @@ mpc52xx_console_setup(struct console *co, char *options) return ret; } - uartclk = psc_ops->getuartclk(np); + uartclk = mpc5xxx_get_bus_frequency(np); if (uartclk == 0) { pr_debug("Could not find uart clock frequency!\n"); return -EINVAL; @@ -1201,6 +1284,7 @@ static struct uart_driver mpc52xx_uart_driver = { static struct of_device_id mpc52xx_uart_of_match[] = { #ifdef CONFIG_PPC_MPC52xx + { .compatible = "fsl,mpc5200b-psc-uart", .data = &mpc5200b_psc_ops, }, { .compatible = "fsl,mpc5200-psc-uart", .data = &mpc52xx_psc_ops, }, /* binding used by old lite5200 device trees: */ { .compatible = "mpc5200-psc-uart", .data = &mpc52xx_psc_ops, }, @@ -1214,7 +1298,7 @@ static struct of_device_id mpc52xx_uart_of_match[] = { }; static int __devinit -mpc52xx_uart_of_probe(struct of_device *op, const struct of_device_id *match) +mpc52xx_uart_of_probe(struct platform_device *op, const struct of_device_id *match) { int idx = -1; unsigned int uartclk; @@ -1233,7 +1317,10 @@ mpc52xx_uart_of_probe(struct of_device *op, const struct of_device_id *match) pr_debug("Found %s assigned to ttyPSC%x\n", mpc52xx_uart_nodes[idx]->full_name, idx); - uartclk = psc_ops->getuartclk(op->dev.of_node); + /* set the uart clock to the input clock of the psc, the different + * prescalers are taken into account in the set_baudrate() methods + * of the respective chip */ + uartclk = mpc5xxx_get_bus_frequency(op->dev.of_node); if (uartclk == 0) { dev_dbg(&op->dev, "Could not find uart clock frequency!\n"); return -EINVAL; @@ -1282,7 +1369,7 @@ mpc52xx_uart_of_probe(struct of_device *op, const struct of_device_id *match) } static int -mpc52xx_uart_of_remove(struct of_device *op) +mpc52xx_uart_of_remove(struct platform_device *op) { struct uart_port *port = dev_get_drvdata(&op->dev); dev_set_drvdata(&op->dev, NULL); @@ -1295,7 +1382,7 @@ mpc52xx_uart_of_remove(struct of_device *op) #ifdef CONFIG_PM static int -mpc52xx_uart_of_suspend(struct of_device *op, pm_message_t state) +mpc52xx_uart_of_suspend(struct platform_device *op, pm_message_t state) { struct uart_port *port = (struct uart_port *) dev_get_drvdata(&op->dev); @@ -1306,7 +1393,7 @@ mpc52xx_uart_of_suspend(struct of_device *op, pm_message_t state) } static int -mpc52xx_uart_of_resume(struct of_device *op) +mpc52xx_uart_of_resume(struct platform_device *op) { struct uart_port *port = (struct uart_port *) dev_get_drvdata(&op->dev); diff --git a/drivers/serial/mrst_max3110.c b/drivers/serial/mrst_max3110.c new file mode 100644 index 00000000000..f6ad1ecbff7 --- /dev/null +++ b/drivers/serial/mrst_max3110.c @@ -0,0 +1,844 @@ +/* + * max3110.c - spi uart protocol driver for Maxim 3110 on Moorestown + * + * Copyright (C) Intel 2008 Feng Tang <feng.tang@intel.com> + * + * This program is free software; you can redistribute it and/or modify it + * under the terms and conditions of the GNU General Public License, + * version 2, as published by the Free Software Foundation. + * + * This program is distributed in the hope it will be useful, but WITHOUT + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for + * more details. + * + * You should have received a copy of the GNU General Public License along with + * this program; if not, write to the Free Software Foundation, Inc., + * 51 Franklin St - Fifth Floor, Boston, MA 02110-1301 USA. + */ + +/* + * Note: + * 1. From Max3110 spec, the Rx FIFO has 8 words, while the Tx FIFO only has + * 1 word. If SPI master controller doesn't support sclk frequency change, + * then the char need be sent out one by one with some delay + * + * 2. Currently only RX availabe interrrupt is used, no need for waiting TXE + * interrupt for a low speed UART device + */ + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/platform_device.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial_reg.h> + +#include <linux/kthread.h> +#include <linux/delay.h> +#include <asm/atomic.h> +#include <linux/spi/spi.h> +#include <linux/spi/dw_spi.h> + +#include "mrst_max3110.h" + +#define PR_FMT "mrst_max3110: " + +#define UART_TX_NEEDED 1 +#define CON_TX_NEEDED 2 +#define BIT_IRQ_PENDING 3 + +struct uart_max3110 { + struct uart_port port; + struct spi_device *spi; + char *name; + + wait_queue_head_t wq; + struct task_struct *main_thread; + struct task_struct *read_thread; + struct mutex thread_mutex;; + + u32 baud; + u16 cur_conf; + u8 clock; + u8 parity, word_7bits; + + unsigned long uart_flags; + + /* console related */ + struct circ_buf con_xmit; + + /* irq related */ + u16 irq; +}; + +/* global data structure, may need be removed */ +struct uart_max3110 *pmax; +static inline void receive_char(struct uart_max3110 *max, u8 ch); +static void receive_chars(struct uart_max3110 *max, + unsigned char *str, int len); +static int max3110_read_multi(struct uart_max3110 *max, int len, u8 *buf); +static void max3110_console_receive(struct uart_max3110 *max); + +int max3110_write_then_read(struct uart_max3110 *max, + const u8 *txbuf, u8 *rxbuf, unsigned len, int always_fast) +{ + struct spi_device *spi = max->spi; + struct spi_message message; + struct spi_transfer x; + int ret; + + if (!txbuf || !rxbuf) + return -EINVAL; + + spi_message_init(&message); + memset(&x, 0, sizeof x); + x.len = len; + x.tx_buf = txbuf; + x.rx_buf = rxbuf; + spi_message_add_tail(&x, &message); + + if (always_fast) + x.speed_hz = 3125000; + else if (max->baud) + x.speed_hz = max->baud; + + /* Do the i/o */ + ret = spi_sync(spi, &message); + return ret; +} + +/* Write a u16 to the device, and return one u16 read back */ +int max3110_out(struct uart_max3110 *max, const u16 out) +{ + u16 tmp; + int ret; + + ret = max3110_write_then_read(max, (u8 *)&out, (u8 *)&tmp, 2, 1); + if (ret) + return ret; + + /* If some valid data is read back */ + if (tmp & MAX3110_READ_DATA_AVAILABLE) + receive_char(max, (tmp & 0xff)); + + return ret; +} + +#define MAX_READ_LEN 20 +/* + * This is usually used to read data from SPIC RX FIFO, which doesn't + * need any delay like flushing character out. It returns how many + * valide bytes are read back + */ +static int max3110_read_multi(struct uart_max3110 *max, int len, u8 *buf) +{ + u16 out[MAX_READ_LEN], in[MAX_READ_LEN]; + u8 *pbuf, valid_str[MAX_READ_LEN]; + int i, j, bytelen; + + if (len > MAX_READ_LEN) { + pr_err(PR_FMT "read len %d is too large\n", len); + return 0; + } + + bytelen = len * 2; + memset(out, 0, bytelen); + memset(in, 0, bytelen); + + if (max3110_write_then_read(max, (u8 *)out, (u8 *)in, bytelen, 1)) + return 0; + + /* If caller don't provide a buffer, then handle received char */ + pbuf = buf ? buf : valid_str; + + for (i = 0, j = 0; i < len; i++) { + if (in[i] & MAX3110_READ_DATA_AVAILABLE) + pbuf[j++] = (u8)(in[i] & 0xff); + } + + if (j && (pbuf == valid_str)) + receive_chars(max, valid_str, j); + + return j; +} + +static void serial_m3110_con_putchar(struct uart_port *port, int ch) +{ + struct uart_max3110 *max = + container_of(port, struct uart_max3110, port); + struct circ_buf *xmit = &max->con_xmit; + + if (uart_circ_chars_free(xmit)) { + xmit->buf[xmit->head] = (char)ch; + xmit->head = (xmit->head + 1) & (PAGE_SIZE - 1); + } + + + if (!test_and_set_bit(CON_TX_NEEDED, &max->uart_flags)) + wake_up_process(max->main_thread); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + * + * The console_lock must be held when we get here. + */ +static void serial_m3110_con_write(struct console *co, + const char *s, unsigned int count) +{ + if (!pmax) + return; + + uart_console_write(&pmax->port, s, count, serial_m3110_con_putchar); +} + +static int __init +serial_m3110_con_setup(struct console *co, char *options) +{ + struct uart_max3110 *max = pmax; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + pr_info(PR_FMT "setting up console\n"); + + if (!max) { + pr_err(PR_FMT "pmax is NULL, return"); + return -ENODEV; + } + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(&max->port, co, baud, parity, bits, flow); +} + +static struct tty_driver *serial_m3110_con_device(struct console *co, + int *index) +{ + struct uart_driver *p = co->data; + *index = co->index; + return p->tty_driver; +} + +static struct uart_driver serial_m3110_reg; +static struct console serial_m3110_console = { + .name = "ttyS", + .write = serial_m3110_con_write, + .device = serial_m3110_con_device, + .setup = serial_m3110_con_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &serial_m3110_reg, +}; + +#define MRST_CONSOLE (&serial_m3110_console) + +static unsigned int serial_m3110_tx_empty(struct uart_port *port) +{ + return 1; +} + +static void serial_m3110_stop_tx(struct uart_port *port) +{ + return; +} + +/* stop_rx will be called in spin_lock env */ +static void serial_m3110_stop_rx(struct uart_port *port) +{ + return; +} + +#define WORDS_PER_XFER 128 +static inline void send_circ_buf(struct uart_max3110 *max, + struct circ_buf *xmit) +{ + int len, left = 0; + u16 obuf[WORDS_PER_XFER], ibuf[WORDS_PER_XFER]; + u8 valid_str[WORDS_PER_XFER]; + int i, j; + + while (!uart_circ_empty(xmit)) { + left = uart_circ_chars_pending(xmit); + while (left) { + len = (left >= WORDS_PER_XFER) ? WORDS_PER_XFER : left; + + memset(obuf, 0, len * 2); + memset(ibuf, 0, len * 2); + for (i = 0; i < len; i++) { + obuf[i] = (u8)xmit->buf[xmit->tail] | WD_TAG; + xmit->tail = (xmit->tail + 1) & + (UART_XMIT_SIZE - 1); + } + max3110_write_then_read(max, (u8 *)obuf, + (u8 *)ibuf, len * 2, 0); + + for (i = 0, j = 0; i < len; i++) { + if (ibuf[i] & MAX3110_READ_DATA_AVAILABLE) + valid_str[j++] = (u8)(ibuf[i] & 0xff); + } + + if (j) + receive_chars(max, valid_str, j); + + max->port.icount.tx += len; + left -= len; + } + } +} + +static void transmit_char(struct uart_max3110 *max) +{ + struct uart_port *port = &max->port; + struct circ_buf *xmit = &port->state->xmit; + + if (uart_circ_empty(xmit) || uart_tx_stopped(port)) + return; + + send_circ_buf(max, xmit); + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(port); + + if (uart_circ_empty(xmit)) + serial_m3110_stop_tx(port); +} + +/* This will be called by uart_write() and tty_write, can't + * go to sleep */ +static void serial_m3110_start_tx(struct uart_port *port) +{ + struct uart_max3110 *max = + container_of(port, struct uart_max3110, port); + + if (!test_and_set_bit(UART_TX_NEEDED, &max->uart_flags)) + wake_up_process(max->main_thread); +} + +static void receive_chars(struct uart_max3110 *max, unsigned char *str, int len) +{ + struct uart_port *port = &max->port; + struct tty_struct *tty; + int usable; + + /* If uart is not opened, just return */ + if (!port->state) + return; + + tty = port->state->port.tty; + if (!tty) + return; /* receive some char before the tty is opened */ + + while (len) { + usable = tty_buffer_request_room(tty, len); + if (usable) { + tty_insert_flip_string(tty, str, usable); + str += usable; + port->icount.rx += usable; + tty_flip_buffer_push(tty); + } + len -= usable; + } +} + +static inline void receive_char(struct uart_max3110 *max, u8 ch) +{ + receive_chars(max, &ch, 1); +} + +static void max3110_console_receive(struct uart_max3110 *max) +{ + int loop = 1, num, total = 0; + u8 recv_buf[512], *pbuf; + + pbuf = recv_buf; + do { + num = max3110_read_multi(max, 8, pbuf); + + if (num) { + loop = 10; + pbuf += num; + total += num; + + if (total >= 500) { + receive_chars(max, recv_buf, total); + pbuf = recv_buf; + total = 0; + } + } + } while (--loop); + + if (total) + receive_chars(max, recv_buf, total); +} + +static int max3110_main_thread(void *_max) +{ + struct uart_max3110 *max = _max; + wait_queue_head_t *wq = &max->wq; + int ret = 0; + struct circ_buf *xmit = &max->con_xmit; + + init_waitqueue_head(wq); + pr_info(PR_FMT "start main thread\n"); + + do { + wait_event_interruptible(*wq, max->uart_flags || kthread_should_stop()); + + mutex_lock(&max->thread_mutex); + + if (test_and_clear_bit(BIT_IRQ_PENDING, &max->uart_flags)) + max3110_console_receive(max); + + /* first handle console output */ + if (test_and_clear_bit(CON_TX_NEEDED, &max->uart_flags)) + send_circ_buf(max, xmit); + + /* handle uart output */ + if (test_and_clear_bit(UART_TX_NEEDED, &max->uart_flags)) + transmit_char(max); + + mutex_unlock(&max->thread_mutex); + + } while (!kthread_should_stop()); + + return ret; +} + +#ifdef CONFIG_MRST_MAX3110_IRQ +static irqreturn_t serial_m3110_irq(int irq, void *dev_id) +{ + struct uart_max3110 *max = dev_id; + + /* max3110's irq is a falling edge, not level triggered, + * so no need to disable the irq */ + if (!test_and_set_bit(BIT_IRQ_PENDING, &max->uart_flags)) + wake_up_process(max->main_thread); + + return IRQ_HANDLED; +} +#else +/* if don't use RX IRQ, then need a thread to polling read */ +static int max3110_read_thread(void *_max) +{ + struct uart_max3110 *max = _max; + + pr_info(PR_FMT "start read thread\n"); + do { + mutex_lock(&max->thread_mutex); + max3110_console_receive(max); + mutex_unlock(&max->thread_mutex); + + set_current_state(TASK_INTERRUPTIBLE); + schedule_timeout(HZ / 20); + } while (!kthread_should_stop()); + + return 0; +} +#endif + +static int serial_m3110_startup(struct uart_port *port) +{ + struct uart_max3110 *max = + container_of(port, struct uart_max3110, port); + u16 config = 0; + int ret = 0; + + if (port->line != 0) + pr_err(PR_FMT "uart port startup failed\n"); + + /* firstly disable all IRQ and config it to 115200, 8n1 */ + config = WC_TAG | WC_FIFO_ENABLE + | WC_1_STOPBITS + | WC_8BIT_WORD + | WC_BAUD_DR2; + ret = max3110_out(max, config); + + /* as we use thread to handle tx/rx, need set low latency */ + port->state->port.tty->low_latency = 1; + +#ifdef CONFIG_MRST_MAX3110_IRQ + ret = request_irq(max->irq, serial_m3110_irq, + IRQ_TYPE_EDGE_FALLING, "max3110", max); + if (ret) + return ret; + + /* enable RX IRQ only */ + config |= WC_RXA_IRQ_ENABLE; + max3110_out(max, config); +#else + /* if IRQ is disabled, start a read thread for input data */ + max->read_thread = + kthread_run(max3110_read_thread, max, "max3110_read"); +#endif + + max->cur_conf = config; + return 0; +} + +static void serial_m3110_shutdown(struct uart_port *port) +{ + struct uart_max3110 *max = + container_of(port, struct uart_max3110, port); + u16 config; + + if (max->read_thread) { + kthread_stop(max->read_thread); + max->read_thread = NULL; + } + +#ifdef CONFIG_MRST_MAX3110_IRQ + free_irq(max->irq, max); +#endif + + /* Disable interrupts from this port */ + config = WC_TAG | WC_SW_SHDI; + max3110_out(max, config); +} + +static void serial_m3110_release_port(struct uart_port *port) +{ +} + +static int serial_m3110_request_port(struct uart_port *port) +{ + return 0; +} + +static void serial_m3110_config_port(struct uart_port *port, int flags) +{ + /* give it fake type */ + port->type = PORT_PXA; +} + +static int +serial_m3110_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + /* we don't want the core code to modify any port params */ + return -EINVAL; +} + + +static const char *serial_m3110_type(struct uart_port *port) +{ + struct uart_max3110 *max = + container_of(port, struct uart_max3110, port); + return max->name; +} + +static void +serial_m3110_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct uart_max3110 *max = + container_of(port, struct uart_max3110, port); + unsigned char cval; + unsigned int baud, parity = 0; + int clk_div = -1; + u16 new_conf = max->cur_conf; + + switch (termios->c_cflag & CSIZE) { + case CS7: + cval = UART_LCR_WLEN7; + new_conf |= WC_7BIT_WORD; + break; + default: + case CS8: + cval = UART_LCR_WLEN8; + new_conf |= WC_8BIT_WORD; + break; + } + + baud = uart_get_baud_rate(port, termios, old, 0, 230400); + + /* first calc the div for 1.8MHZ clock case */ + switch (baud) { + case 300: + clk_div = WC_BAUD_DR384; + break; + case 600: + clk_div = WC_BAUD_DR192; + break; + case 1200: + clk_div = WC_BAUD_DR96; + break; + case 2400: + clk_div = WC_BAUD_DR48; + break; + case 4800: + clk_div = WC_BAUD_DR24; + break; + case 9600: + clk_div = WC_BAUD_DR12; + break; + case 19200: + clk_div = WC_BAUD_DR6; + break; + case 38400: + clk_div = WC_BAUD_DR3; + break; + case 57600: + clk_div = WC_BAUD_DR2; + break; + case 115200: + clk_div = WC_BAUD_DR1; + break; + case 230400: + if (max->clock & MAX3110_HIGH_CLK) + break; + default: + /* pick the previous baud rate */ + baud = max->baud; + clk_div = max->cur_conf & WC_BAUD_DIV_MASK; + tty_termios_encode_baud_rate(termios, baud, baud); + } + + if (max->clock & MAX3110_HIGH_CLK) { + clk_div += 1; + /* high clk version max3110 doesn't support B300 */ + if (baud == 300) + baud = 600; + if (baud == 230400) + clk_div = WC_BAUD_DR1; + tty_termios_encode_baud_rate(termios, baud, baud); + } + + new_conf = (new_conf & ~WC_BAUD_DIV_MASK) | clk_div; + if (termios->c_cflag & CSTOPB) + new_conf |= WC_2_STOPBITS; + else + new_conf &= ~WC_2_STOPBITS; + + if (termios->c_cflag & PARENB) { + new_conf |= WC_PARITY_ENABLE; + parity |= UART_LCR_PARITY; + } else + new_conf &= ~WC_PARITY_ENABLE; + + if (!(termios->c_cflag & PARODD)) + parity |= UART_LCR_EPAR; + max->parity = parity; + + uart_update_timeout(port, termios->c_cflag, baud); + + new_conf |= WC_TAG; + if (new_conf != max->cur_conf) { + max3110_out(max, new_conf); + max->cur_conf = new_conf; + max->baud = baud; + } +} + +/* don't handle hw handshaking */ +static unsigned int serial_m3110_get_mctrl(struct uart_port *port) +{ + return TIOCM_DSR | TIOCM_CAR | TIOCM_DSR; +} + +static void serial_m3110_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ +} + +static void serial_m3110_break_ctl(struct uart_port *port, int break_state) +{ +} + +static void serial_m3110_pm(struct uart_port *port, unsigned int state, + unsigned int oldstate) +{ +} + +static void serial_m3110_enable_ms(struct uart_port *port) +{ +} + +struct uart_ops serial_m3110_ops = { + .tx_empty = serial_m3110_tx_empty, + .set_mctrl = serial_m3110_set_mctrl, + .get_mctrl = serial_m3110_get_mctrl, + .stop_tx = serial_m3110_stop_tx, + .start_tx = serial_m3110_start_tx, + .stop_rx = serial_m3110_stop_rx, + .enable_ms = serial_m3110_enable_ms, + .break_ctl = serial_m3110_break_ctl, + .startup = serial_m3110_startup, + .shutdown = serial_m3110_shutdown, + .set_termios = serial_m3110_set_termios, /* must have */ + .pm = serial_m3110_pm, + .type = serial_m3110_type, + .release_port = serial_m3110_release_port, + .request_port = serial_m3110_request_port, + .config_port = serial_m3110_config_port, + .verify_port = serial_m3110_verify_port, +}; + +static struct uart_driver serial_m3110_reg = { + .owner = THIS_MODULE, + .driver_name = "MRST serial", + .dev_name = "ttyS", + .major = TTY_MAJOR, + .minor = 64, + .nr = 1, + .cons = MRST_CONSOLE, +}; + +static int serial_m3110_suspend(struct spi_device *spi, pm_message_t state) +{ + return 0; +} + +static int serial_m3110_resume(struct spi_device *spi) +{ + return 0; +} + +static struct dw_spi_chip spi0_uart = { + .poll_mode = 1, + .enable_dma = 0, + .type = SPI_FRF_SPI, +}; + +static int serial_m3110_probe(struct spi_device *spi) +{ + struct uart_max3110 *max; + int ret; + unsigned char *buffer; + u16 res; + max = kzalloc(sizeof(*max), GFP_KERNEL); + if (!max) + return -ENOMEM; + + /* set spi info */ + spi->mode = SPI_MODE_0; + spi->bits_per_word = 16; + max->clock = MAX3110_HIGH_CLK; + spi->controller_data = &spi0_uart; + + spi_setup(spi); + + max->port.type = PORT_PXA; /* need apply for a max3110 type */ + max->port.fifosize = 2; /* only have 16b buffer */ + max->port.ops = &serial_m3110_ops; + max->port.line = 0; + max->port.dev = &spi->dev; + max->port.uartclk = 115200; + + max->spi = spi; + max->name = spi->modalias; /* use spi name as the name */ + max->irq = (u16)spi->irq; + + mutex_init(&max->thread_mutex); + + max->word_7bits = 0; + max->parity = 0; + max->baud = 0; + + max->cur_conf = 0; + max->uart_flags = 0; + + /* Check if reading configuration register returns something sane */ + + res = RC_TAG; + ret = max3110_write_then_read(max, (u8 *)&res, (u8 *)&res, 2, 0); + if (ret < 0 || res == 0 || res == 0xffff) { + printk(KERN_ERR "MAX3111 deemed not present (conf reg %04x)", + res); + ret = -ENODEV; + goto err_get_page; + } + buffer = (unsigned char *)__get_free_page(GFP_KERNEL); + if (!buffer) { + ret = -ENOMEM; + goto err_get_page; + } + max->con_xmit.buf = (unsigned char *)buffer; + max->con_xmit.head = max->con_xmit.tail = 0; + + max->main_thread = kthread_run(max3110_main_thread, + max, "max3110_main"); + if (IS_ERR(max->main_thread)) { + ret = PTR_ERR(max->main_thread); + goto err_kthread; + } + + pmax = max; + /* give membase a psudo value to pass serial_core's check */ + max->port.membase = (void *)0xff110000; + uart_add_one_port(&serial_m3110_reg, &max->port); + + return 0; + +err_kthread: + free_page((unsigned long)buffer); +err_get_page: + pmax = NULL; + kfree(max); + return ret; +} + +static int max3110_remove(struct spi_device *dev) +{ + struct uart_max3110 *max = pmax; + + if (!pmax) + return 0; + + pmax = NULL; + uart_remove_one_port(&serial_m3110_reg, &max->port); + + free_page((unsigned long)max->con_xmit.buf); + + if (max->main_thread) + kthread_stop(max->main_thread); + + kfree(max); + return 0; +} + +static struct spi_driver uart_max3110_driver = { + .driver = { + .name = "spi_max3111", + .bus = &spi_bus_type, + .owner = THIS_MODULE, + }, + .probe = serial_m3110_probe, + .remove = __devexit_p(max3110_remove), + .suspend = serial_m3110_suspend, + .resume = serial_m3110_resume, +}; + + +int __init serial_m3110_init(void) +{ + int ret = 0; + + ret = uart_register_driver(&serial_m3110_reg); + if (ret) + return ret; + + ret = spi_register_driver(&uart_max3110_driver); + if (ret) + uart_unregister_driver(&serial_m3110_reg); + + return ret; +} + +void __exit serial_m3110_exit(void) +{ + spi_unregister_driver(&uart_max3110_driver); + uart_unregister_driver(&serial_m3110_reg); +} + +module_init(serial_m3110_init); +module_exit(serial_m3110_exit); + +MODULE_LICENSE("GPL"); +MODULE_ALIAS("max3110-uart"); diff --git a/drivers/serial/mrst_max3110.h b/drivers/serial/mrst_max3110.h new file mode 100644 index 00000000000..363478acb2c --- /dev/null +++ b/drivers/serial/mrst_max3110.h @@ -0,0 +1,59 @@ +#ifndef _MRST_MAX3110_H +#define _MRST_MAX3110_H + +#define MAX3110_HIGH_CLK 0x1 /* 3.6864 MHZ */ +#define MAX3110_LOW_CLK 0x0 /* 1.8432 MHZ */ + +/* status bits for all 4 MAX3110 operate modes */ +#define MAX3110_READ_DATA_AVAILABLE (1 << 15) +#define MAX3110_WRITE_BUF_EMPTY (1 << 14) + +#define WC_TAG (3 << 14) +#define RC_TAG (1 << 14) +#define WD_TAG (2 << 14) +#define RD_TAG (0 << 14) + +/* bits def for write configuration */ +#define WC_FIFO_ENABLE_MASK (1 << 13) +#define WC_FIFO_ENABLE (0 << 13) + +#define WC_SW_SHDI (1 << 12) + +#define WC_IRQ_MASK (0xF << 8) +#define WC_TXE_IRQ_ENABLE (1 << 11) /* TX empty irq */ +#define WC_RXA_IRQ_ENABLE (1 << 10) /* RX availabe irq */ +#define WC_PAR_HIGH_IRQ_ENABLE (1 << 9) +#define WC_REC_ACT_IRQ_ENABLE (1 << 8) + +#define WC_IRDA_ENABLE (1 << 7) + +#define WC_STOPBITS_MASK (1 << 6) +#define WC_2_STOPBITS (1 << 6) +#define WC_1_STOPBITS (0 << 6) + +#define WC_PARITY_ENABLE_MASK (1 << 5) +#define WC_PARITY_ENABLE (1 << 5) + +#define WC_WORDLEN_MASK (1 << 4) +#define WC_7BIT_WORD (1 << 4) +#define WC_8BIT_WORD (0 << 4) + +#define WC_BAUD_DIV_MASK (0xF) +#define WC_BAUD_DR1 (0x0) +#define WC_BAUD_DR2 (0x1) +#define WC_BAUD_DR4 (0x2) +#define WC_BAUD_DR8 (0x3) +#define WC_BAUD_DR16 (0x4) +#define WC_BAUD_DR32 (0x5) +#define WC_BAUD_DR64 (0x6) +#define WC_BAUD_DR128 (0x7) +#define WC_BAUD_DR3 (0x8) +#define WC_BAUD_DR6 (0x9) +#define WC_BAUD_DR12 (0xA) +#define WC_BAUD_DR24 (0xB) +#define WC_BAUD_DR48 (0xC) +#define WC_BAUD_DR96 (0xD) +#define WC_BAUD_DR192 (0xE) +#define WC_BAUD_DR384 (0xF) + +#endif diff --git a/drivers/serial/nwpserial.c b/drivers/serial/nwpserial.c index e65b0d9202a..de173671e3d 100644 --- a/drivers/serial/nwpserial.c +++ b/drivers/serial/nwpserial.c @@ -344,7 +344,7 @@ int nwpserial_register_port(struct uart_port *port) mutex_lock(&nwpserial_mutex); - dn = to_of_device(port->dev)->dev.of_node; + dn = port->dev->of_node; if (dn == NULL) goto out; diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c index a48d9080f55..2af8fd11312 100644 --- a/drivers/serial/of_serial.c +++ b/drivers/serial/of_serial.c @@ -14,11 +14,10 @@ #include <linux/slab.h> #include <linux/serial_core.h> #include <linux/serial_8250.h> +#include <linux/of_address.h> #include <linux/of_platform.h> #include <linux/nwpserial.h> -#include <asm/prom.h> - struct of_serial_info { int type; int line; @@ -27,7 +26,7 @@ struct of_serial_info { /* * Fill a struct uart_port for a given device node */ -static int __devinit of_platform_serial_setup(struct of_device *ofdev, +static int __devinit of_platform_serial_setup(struct platform_device *ofdev, int type, struct uart_port *port) { struct resource resource; @@ -80,7 +79,7 @@ static int __devinit of_platform_serial_setup(struct of_device *ofdev, /* * Try to register a serial port */ -static int __devinit of_platform_serial_probe(struct of_device *ofdev, +static int __devinit of_platform_serial_probe(struct platform_device *ofdev, const struct of_device_id *id) { struct of_serial_info *info; @@ -134,7 +133,7 @@ out: /* * Release a line */ -static int of_platform_serial_remove(struct of_device *ofdev) +static int of_platform_serial_remove(struct platform_device *ofdev) { struct of_serial_info *info = dev_get_drvdata(&ofdev->dev); switch (info->type) { diff --git a/drivers/serial/s5pv210.c b/drivers/serial/s5pv210.c index 4a789e5361a..6ebccd70a70 100644 --- a/drivers/serial/s5pv210.c +++ b/drivers/serial/s5pv210.c @@ -28,8 +28,12 @@ static int s5pv210_serial_setsource(struct uart_port *port, struct s3c24xx_uart_clksrc *clk) { + struct s3c2410_uartcfg *cfg = port->dev->platform_data; unsigned long ucon = rd_regl(port, S3C2410_UCON); + if ((cfg->clocks_size) == 1) + return 0; + if (strcmp(clk->name, "pclk") == 0) ucon &= ~S5PV210_UCON_CLKMASK; else if (strcmp(clk->name, "uclk1") == 0) @@ -47,10 +51,14 @@ static int s5pv210_serial_setsource(struct uart_port *port, static int s5pv210_serial_getsource(struct uart_port *port, struct s3c24xx_uart_clksrc *clk) { + struct s3c2410_uartcfg *cfg = port->dev->platform_data; u32 ucon = rd_regl(port, S3C2410_UCON); clk->divisor = 1; + if ((cfg->clocks_size) == 1) + return 0; + switch (ucon & S5PV210_UCON_CLKMASK) { case S5PV210_UCON_PCLK: clk->name = "pclk"; diff --git a/drivers/serial/samsung.c b/drivers/serial/samsung.c index a9d6c5626a0..b1156ba8ad1 100644 --- a/drivers/serial/samsung.c +++ b/drivers/serial/samsung.c @@ -705,8 +705,13 @@ static void s3c24xx_serial_set_termios(struct uart_port *port, if (ourport->info->has_divslot) { unsigned int div = ourport->baudclk_rate / baud; - udivslot = udivslot_table[div & 15]; - dbg("udivslot = %04x (div %d)\n", udivslot, div & 15); + if (cfg->has_fracval) { + udivslot = (div & 15); + dbg("fracval = %04x\n", udivslot); + } else { + udivslot = udivslot_table[div & 15]; + dbg("udivslot = %04x (div %d)\n", udivslot, div & 15); + } } switch (termios->c_cflag & CSIZE) { diff --git a/drivers/serial/serial_core.c b/drivers/serial/serial_core.c index 7f283070951..cd8511298bc 100644 --- a/drivers/serial/serial_core.c +++ b/drivers/serial/serial_core.c @@ -58,9 +58,9 @@ static struct lock_class_key port_lock_key; #define uart_console(port) (0) #endif -static void uart_change_speed(struct uart_state *state, +static void uart_change_speed(struct tty_struct *tty, struct uart_state *state, struct ktermios *old_termios); -static void uart_wait_until_sent(struct tty_struct *tty, int timeout); +static void __uart_wait_until_sent(struct uart_port *port, int timeout); static void uart_change_pm(struct uart_state *state, int pm_state); /* @@ -137,7 +137,7 @@ uart_update_mctrl(struct uart_port *port, unsigned int set, unsigned int clear) * Startup the port. This will be called once per open. All calls * will be serialised by the per-port mutex. */ -static int uart_startup(struct uart_state *state, int init_hw) +static int uart_startup(struct tty_struct *tty, struct uart_state *state, int init_hw) { struct uart_port *uport = state->uart_port; struct tty_port *port = &state->port; @@ -152,7 +152,7 @@ static int uart_startup(struct uart_state *state, int init_hw) * once we have successfully opened the port. Also set * up the tty->alt_speed kludge */ - set_bit(TTY_IO_ERROR, &port->tty->flags); + set_bit(TTY_IO_ERROR, &tty->flags); if (uport->type == PORT_UNKNOWN) return 0; @@ -177,26 +177,26 @@ static int uart_startup(struct uart_state *state, int init_hw) /* * Initialise the hardware port settings. */ - uart_change_speed(state, NULL); + uart_change_speed(tty, state, NULL); /* * Setup the RTS and DTR signals once the * port is open and ready to respond. */ - if (port->tty->termios->c_cflag & CBAUD) + if (tty->termios->c_cflag & CBAUD) uart_set_mctrl(uport, TIOCM_RTS | TIOCM_DTR); } if (port->flags & ASYNC_CTS_FLOW) { spin_lock_irq(&uport->lock); if (!(uport->ops->get_mctrl(uport) & TIOCM_CTS)) - port->tty->hw_stopped = 1; + tty->hw_stopped = 1; spin_unlock_irq(&uport->lock); } set_bit(ASYNCB_INITIALIZED, &port->flags); - clear_bit(TTY_IO_ERROR, &port->tty->flags); + clear_bit(TTY_IO_ERROR, &tty->flags); } if (retval && capable(CAP_SYS_ADMIN)) @@ -210,11 +210,10 @@ static int uart_startup(struct uart_state *state, int init_hw) * DTR is dropped if the hangup on close termio flag is on. Calls to * uart_shutdown are serialised by the per-port semaphore. */ -static void uart_shutdown(struct uart_state *state) +static void uart_shutdown(struct tty_struct *tty, struct uart_state *state) { struct uart_port *uport = state->uart_port; struct tty_port *port = &state->port; - struct tty_struct *tty = port->tty; /* * Set the TTY IO error marker @@ -430,11 +429,10 @@ uart_get_divisor(struct uart_port *port, unsigned int baud) EXPORT_SYMBOL(uart_get_divisor); /* FIXME: Consistent locking policy */ -static void -uart_change_speed(struct uart_state *state, struct ktermios *old_termios) +static void uart_change_speed(struct tty_struct *tty, struct uart_state *state, + struct ktermios *old_termios) { struct tty_port *port = &state->port; - struct tty_struct *tty = port->tty; struct uart_port *uport = state->uart_port; struct ktermios *termios; @@ -463,8 +461,8 @@ uart_change_speed(struct uart_state *state, struct ktermios *old_termios) uport->ops->set_termios(uport, termios, old_termios); } -static inline int -__uart_put_char(struct uart_port *port, struct circ_buf *circ, unsigned char c) +static inline int __uart_put_char(struct uart_port *port, + struct circ_buf *circ, unsigned char c) { unsigned long flags; int ret = 0; @@ -494,8 +492,8 @@ static void uart_flush_chars(struct tty_struct *tty) uart_start(tty); } -static int -uart_write(struct tty_struct *tty, const unsigned char *buf, int count) +static int uart_write(struct tty_struct *tty, + const unsigned char *buf, int count) { struct uart_state *state = tty->driver_data; struct uart_port *port; @@ -675,7 +673,7 @@ static int uart_get_info(struct uart_state *state, return 0; } -static int uart_set_info(struct uart_state *state, +static int uart_set_info(struct tty_struct *tty, struct uart_state *state, struct serial_struct __user *newinfo) { struct serial_struct new_serial; @@ -770,7 +768,7 @@ static int uart_set_info(struct uart_state *state, * We need to shutdown the serial port at the old * port/type/irq combination. */ - uart_shutdown(state); + uart_shutdown(tty, state); } if (change_port) { @@ -869,25 +867,27 @@ static int uart_set_info(struct uart_state *state, "is deprecated.\n", current->comm, tty_name(port->tty, buf)); } - uart_change_speed(state, NULL); + uart_change_speed(tty, state, NULL); } } else - retval = uart_startup(state, 1); + retval = uart_startup(tty, state, 1); exit: mutex_unlock(&port->mutex); return retval; } - -/* - * uart_get_lsr_info - get line status register info. - * Note: uart_ioctl protects us against hangups. +/** + * uart_get_lsr_info - get line status register info + * @tty: tty associated with the UART + * @state: UART being queried + * @value: returned modem value + * + * Note: uart_ioctl protects us against hangups. */ -static int uart_get_lsr_info(struct uart_state *state, - unsigned int __user *value) +static int uart_get_lsr_info(struct tty_struct *tty, + struct uart_state *state, unsigned int __user *value) { struct uart_port *uport = state->uart_port; - struct tty_port *port = &state->port; unsigned int result; result = uport->ops->tx_empty(uport); @@ -900,7 +900,7 @@ static int uart_get_lsr_info(struct uart_state *state, */ if (uport->x_char || ((uart_circ_chars_pending(&state->xmit) > 0) && - !port->tty->stopped && !port->tty->hw_stopped)) + !tty->stopped && !tty->hw_stopped)) result &= ~TIOCSER_TEMT; return put_user(result, value); @@ -961,7 +961,7 @@ static int uart_break_ctl(struct tty_struct *tty, int break_state) return 0; } -static int uart_do_autoconfig(struct uart_state *state) +static int uart_do_autoconfig(struct tty_struct *tty,struct uart_state *state) { struct uart_port *uport = state->uart_port; struct tty_port *port = &state->port; @@ -980,7 +980,7 @@ static int uart_do_autoconfig(struct uart_state *state) ret = -EBUSY; if (tty_port_users(port) == 1) { - uart_shutdown(state); + uart_shutdown(tty, state); /* * If we already have a port type configured, @@ -999,7 +999,7 @@ static int uart_do_autoconfig(struct uart_state *state) */ uport->ops->config_port(uport, flags); - ret = uart_startup(state, 1); + ret = uart_startup(tty, state, 1); } mutex_unlock(&port->mutex); return ret; @@ -1122,11 +1122,11 @@ uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd, break; case TIOCSSERIAL: - ret = uart_set_info(state, uarg); + ret = uart_set_info(tty, state, uarg); break; case TIOCSERCONFIG: - ret = uart_do_autoconfig(state); + ret = uart_do_autoconfig(tty, state); break; case TIOCSERGWILD: /* obsolete */ @@ -1172,7 +1172,7 @@ uart_ioctl(struct tty_struct *tty, struct file *filp, unsigned int cmd, */ switch (cmd) { case TIOCSERGETLSR: /* Get line status register */ - ret = uart_get_lsr_info(state, uarg); + ret = uart_get_lsr_info(tty, state, uarg); break; default: { @@ -1194,7 +1194,7 @@ static void uart_set_ldisc(struct tty_struct *tty) struct uart_port *uport = state->uart_port; if (uport->ops->set_ldisc) - uport->ops->set_ldisc(uport); + uport->ops->set_ldisc(uport, tty->termios->c_line); } static void uart_set_termios(struct tty_struct *tty, @@ -1219,7 +1219,7 @@ static void uart_set_termios(struct tty_struct *tty, return; } - uart_change_speed(state, old_termios); + uart_change_speed(tty, state, old_termios); /* Handle transition to B0 status */ if ((old_termios->c_cflag & CBAUD) && !(cflag & CBAUD)) @@ -1272,8 +1272,9 @@ static void uart_close(struct tty_struct *tty, struct file *filp) struct uart_state *state = tty->driver_data; struct tty_port *port; struct uart_port *uport; + unsigned long flags; - BUG_ON(!kernel_locked()); + BUG_ON(!tty_locked()); if (!state) return; @@ -1284,9 +1285,12 @@ static void uart_close(struct tty_struct *tty, struct file *filp) pr_debug("uart_close(%d) called\n", uport->line); mutex_lock(&port->mutex); + spin_lock_irqsave(&port->lock, flags); - if (tty_hung_up_p(filp)) + if (tty_hung_up_p(filp)) { + spin_unlock_irqrestore(&port->lock, flags); goto done; + } if ((tty->count == 1) && (port->count != 1)) { /* @@ -1305,8 +1309,10 @@ static void uart_close(struct tty_struct *tty, struct file *filp) tty->name, port->count); port->count = 0; } - if (port->count) + if (port->count) { + spin_unlock_irqrestore(&port->lock, flags); goto done; + } /* * Now we wait for the transmit buffer to clear; and we notify @@ -1314,9 +1320,18 @@ static void uart_close(struct tty_struct *tty, struct file *filp) * setting tty->closing. */ tty->closing = 1; + spin_unlock_irqrestore(&port->lock, flags); - if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE) - tty_wait_until_sent(tty, msecs_to_jiffies(port->closing_wait)); + if (port->closing_wait != ASYNC_CLOSING_WAIT_NONE) { + /* + * hack: open-coded tty_wait_until_sent to avoid + * recursive tty_lock + */ + long timeout = msecs_to_jiffies(port->closing_wait); + if (wait_event_interruptible_timeout(tty->write_wait, + !tty_chars_in_buffer(tty), timeout) >= 0) + __uart_wait_until_sent(uport, timeout); + } /* * At this point, we stop accepting input. To do this, we @@ -1332,45 +1347,47 @@ static void uart_close(struct tty_struct *tty, struct file *filp) * has completely drained; this is especially * important if there is a transmit FIFO! */ - uart_wait_until_sent(tty, uport->timeout); + __uart_wait_until_sent(uport, uport->timeout); } - uart_shutdown(state); + uart_shutdown(tty, state); uart_flush_buffer(tty); tty_ldisc_flush(tty); - tty->closing = 0; tty_port_tty_set(port, NULL); + spin_lock_irqsave(&port->lock, flags); + tty->closing = 0; if (port->blocked_open) { + spin_unlock_irqrestore(&port->lock, flags); if (port->close_delay) msleep_interruptible(port->close_delay); + spin_lock_irqsave(&port->lock, flags); } else if (!uart_console(uport)) { + spin_unlock_irqrestore(&port->lock, flags); uart_change_pm(state, 3); + spin_lock_irqsave(&port->lock, flags); } /* * Wake up anyone trying to open this port. */ clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags); + spin_unlock_irqrestore(&port->lock, flags); wake_up_interruptible(&port->open_wait); done: mutex_unlock(&port->mutex); } -static void uart_wait_until_sent(struct tty_struct *tty, int timeout) +static void __uart_wait_until_sent(struct uart_port *port, int timeout) { - struct uart_state *state = tty->driver_data; - struct uart_port *port = state->uart_port; unsigned long char_time, expire; if (port->type == PORT_UNKNOWN || port->fifosize == 0) return; - lock_kernel(); - /* * Set the check interval to be 1/5 of the estimated time to * send a single character, and make it at least 1. The check @@ -1416,7 +1433,16 @@ static void uart_wait_until_sent(struct tty_struct *tty, int timeout) break; } set_current_state(TASK_RUNNING); /* might not be needed */ - unlock_kernel(); +} + +static void uart_wait_until_sent(struct tty_struct *tty, int timeout) +{ + struct uart_state *state = tty->driver_data; + struct uart_port *port = state->uart_port; + + tty_lock(); + __uart_wait_until_sent(port, timeout); + tty_unlock(); } /* @@ -1429,16 +1455,19 @@ static void uart_hangup(struct tty_struct *tty) { struct uart_state *state = tty->driver_data; struct tty_port *port = &state->port; + unsigned long flags; - BUG_ON(!kernel_locked()); + BUG_ON(!tty_locked()); pr_debug("uart_hangup(%d)\n", state->uart_port->line); mutex_lock(&port->mutex); if (port->flags & ASYNC_NORMAL_ACTIVE) { uart_flush_buffer(tty); - uart_shutdown(state); + uart_shutdown(tty, state); + spin_lock_irqsave(&port->lock, flags); port->count = 0; clear_bit(ASYNCB_NORMAL_ACTIVE, &port->flags); + spin_unlock_irqrestore(&port->lock, flags); tty_port_tty_set(port, NULL); wake_up_interruptible(&port->open_wait); wake_up_interruptible(&port->delta_msr_wait); @@ -1446,15 +1475,19 @@ static void uart_hangup(struct tty_struct *tty) mutex_unlock(&port->mutex); } -/* - * Copy across the serial console cflag setting into the termios settings - * for the initial open of the port. This allows continuity between the - * kernel settings, and the settings init adopts when it opens the port - * for the first time. +/** + * uart_update_termios - update the terminal hw settings + * @tty: tty associated with UART + * @state: UART to update + * + * Copy across the serial console cflag setting into the termios settings + * for the initial open of the port. This allows continuity between the + * kernel settings, and the settings init adopts when it opens the port + * for the first time. */ -static void uart_update_termios(struct uart_state *state) +static void uart_update_termios(struct tty_struct *tty, + struct uart_state *state) { - struct tty_struct *tty = state->port.tty; struct uart_port *port = state->uart_port; if (uart_console(port) && port->cons->cflag) { @@ -1471,7 +1504,7 @@ static void uart_update_termios(struct uart_state *state) /* * Make termios settings take effect. */ - uart_change_speed(state, NULL); + uart_change_speed(tty, state, NULL); /* * And finally enable the RTS and DTR signals. @@ -1481,90 +1514,37 @@ static void uart_update_termios(struct uart_state *state) } } -/* - * Block the open until the port is ready. We must be called with - * the per-port semaphore held. - */ -static int -uart_block_til_ready(struct file *filp, struct uart_state *state) +static int uart_carrier_raised(struct tty_port *port) { - DECLARE_WAITQUEUE(wait, current); + struct uart_state *state = container_of(port, struct uart_state, port); struct uart_port *uport = state->uart_port; - struct tty_port *port = &state->port; - unsigned int mctrl; - - port->blocked_open++; - port->count--; - - add_wait_queue(&port->open_wait, &wait); - while (1) { - set_current_state(TASK_INTERRUPTIBLE); - - /* - * If we have been hung up, tell userspace/restart open. - */ - if (tty_hung_up_p(filp) || port->tty == NULL) - break; - - /* - * If the port has been closed, tell userspace/restart open. - */ - if (!(port->flags & ASYNC_INITIALIZED)) - break; + int mctrl; + spin_lock_irq(&uport->lock); + uport->ops->enable_ms(uport); + mctrl = uport->ops->get_mctrl(uport); + spin_unlock_irq(&uport->lock); + if (mctrl & TIOCM_CAR) + return 1; + return 0; +} - /* - * If non-blocking mode is set, or CLOCAL mode is set, - * we don't want to wait for the modem status lines to - * indicate that the port is ready. - * - * Also, if the port is not enabled/configured, we want - * to allow the open to succeed here. Note that we will - * have set TTY_IO_ERROR for a non-existant port. - */ - if ((filp->f_flags & O_NONBLOCK) || - (port->tty->termios->c_cflag & CLOCAL) || - (port->tty->flags & (1 << TTY_IO_ERROR))) - break; +static void uart_dtr_rts(struct tty_port *port, int onoff) +{ + struct uart_state *state = container_of(port, struct uart_state, port); + struct uart_port *uport = state->uart_port; - /* - * Set DTR to allow modem to know we're waiting. Do - * not set RTS here - we want to make sure we catch - * the data from the modem. - */ - if (port->tty->termios->c_cflag & CBAUD) - uart_set_mctrl(uport, TIOCM_DTR); + if (onoff) { + uart_set_mctrl(uport, TIOCM_DTR | TIOCM_RTS); /* - * and wait for the carrier to indicate that the - * modem is ready for us. + * If this is the first open to succeed, + * adjust things to suit. */ - spin_lock_irq(&uport->lock); - uport->ops->enable_ms(uport); - mctrl = uport->ops->get_mctrl(uport); - spin_unlock_irq(&uport->lock); - if (mctrl & TIOCM_CAR) - break; - - mutex_unlock(&port->mutex); - schedule(); - mutex_lock(&port->mutex); - - if (signal_pending(current)) - break; + if (!test_and_set_bit(ASYNCB_NORMAL_ACTIVE, &port->flags)) + uart_update_termios(port->tty, state); } - set_current_state(TASK_RUNNING); - remove_wait_queue(&port->open_wait, &wait); - - port->count++; - port->blocked_open--; - - if (signal_pending(current)) - return -ERESTARTSYS; - - if (!port->tty || tty_hung_up_p(filp)) - return -EAGAIN; - - return 0; + else + uart_clear_mctrl(uport, TIOCM_DTR | TIOCM_RTS); } static struct uart_state *uart_get(struct uart_driver *drv, int line) @@ -1611,7 +1591,7 @@ static int uart_open(struct tty_struct *tty, struct file *filp) struct tty_port *port; int retval, line = tty->index; - BUG_ON(!kernel_locked()); + BUG_ON(!tty_locked()); pr_debug("uart_open(%d) called\n", line); /* @@ -1668,23 +1648,14 @@ static int uart_open(struct tty_struct *tty, struct file *filp) /* * Start up the serial port. */ - retval = uart_startup(state, 0); + retval = uart_startup(tty, state, 0); /* * If we succeeded, wait until the port is ready. */ - if (retval == 0) - retval = uart_block_til_ready(filp, state); mutex_unlock(&port->mutex); - - /* - * If this is the first open to succeed, adjust things to suit. - */ - if (retval == 0 && !(port->flags & ASYNC_NORMAL_ACTIVE)) { - set_bit(ASYNCB_NORMAL_ACTIVE, &port->flags); - - uart_update_termios(state); - } + if (retval == 0) + retval = tty_port_block_til_ready(port, tty, filp); fail: return retval; @@ -2010,9 +1981,13 @@ int uart_suspend_port(struct uart_driver *drv, struct uart_port *uport) struct tty_port *port = &state->port; struct device *tty_dev; struct uart_match match = {uport, drv}; + struct tty_struct *tty; mutex_lock(&port->mutex); + /* Must be inside the mutex lock until we convert to tty_port */ + tty = port->tty; + tty_dev = device_find_child(uport->dev, &match, serial_match_port); if (device_may_wakeup(tty_dev)) { enable_irq_wake(uport->irq); @@ -2105,9 +2080,12 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport) ops->set_mctrl(uport, 0); spin_unlock_irq(&uport->lock); if (console_suspend_enabled || !uart_console(uport)) { + /* Protected by port mutex for now */ + struct tty_struct *tty = port->tty; ret = ops->startup(uport); if (ret == 0) { - uart_change_speed(state, NULL); + if (tty) + uart_change_speed(tty, state, NULL); spin_lock_irq(&uport->lock); ops->set_mctrl(uport, uport->mctrl); ops->start_tx(uport); @@ -2119,7 +2097,7 @@ int uart_resume_port(struct uart_driver *drv, struct uart_port *uport) * Clear the "initialized" flag so we won't try * to call the low level drivers shutdown method. */ - uart_shutdown(state); + uart_shutdown(tty, state); } } @@ -2312,6 +2290,11 @@ static const struct tty_operations uart_ops = { #endif }; +static const struct tty_port_operations uart_port_ops = { + .carrier_raised = uart_carrier_raised, + .dtr_rts = uart_dtr_rts, +}; + /** * uart_register_driver - register a driver with the uart core layer * @drv: low level driver structure @@ -2368,6 +2351,7 @@ int uart_register_driver(struct uart_driver *drv) struct tty_port *port = &state->port; tty_port_init(port); + port->ops = &uart_port_ops; port->close_delay = 500; /* .5 seconds */ port->closing_wait = 30000; /* 30 seconds */ tasklet_init(&state->tlet, uart_tasklet_action, diff --git a/drivers/serial/serial_cs.c b/drivers/serial/serial_cs.c index ab17c08ddc0..141c69554bd 100644 --- a/drivers/serial/serial_cs.c +++ b/drivers/serial/serial_cs.c @@ -45,7 +45,6 @@ #include <asm/io.h> #include <asm/system.h> -#include <pcmcia/cs_types.h> #include <pcmcia/cs.h> #include <pcmcia/cistpl.h> #include <pcmcia/ciscode.h> @@ -115,16 +114,14 @@ static void quirk_setup_brainboxes_0104(struct pcmcia_device *link, struct uart_ static int quirk_post_ibm(struct pcmcia_device *link) { - conf_reg_t reg = { 0, CS_READ, 0x800, 0 }; + u8 val; int ret; - ret = pcmcia_access_configuration_register(link, ®); + ret = pcmcia_read_config_byte(link, 0x800, &val); if (ret) goto failed; - reg.Action = CS_WRITE; - reg.Value = reg.Value | 1; - ret = pcmcia_access_configuration_register(link, ®); + ret = pcmcia_write_config_byte(link, 0x800, val | 1); if (ret) goto failed; return 0; @@ -338,8 +335,8 @@ static int serial_probe(struct pcmcia_device *link) info->p_dev = link; link->priv = info; - link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; - link->io.NumPorts1 = 8; + link->resource[0]->flags |= IO_DATA_PATH_WIDTH_8; + link->resource[0]->end = 8; link->conf.Attributes = CONF_ENABLE_IRQ; if (do_sound) { link->conf.Attributes |= CONF_ENABLE_SPKR; @@ -427,12 +424,13 @@ static int simple_config_check(struct pcmcia_device *p_dev, p_dev->conf.Vpp = cf->vpp1.param[CISTPL_POWER_VNOM] / 10000; + p_dev->io_lines = ((*try & 0x1) == 0) ? + 16 : cf->io.flags & CISTPL_IO_LINES_MASK; + if ((cf->io.nwin > 0) && (cf->io.win[0].len == size_table[(*try >> 1)]) && (cf->io.win[0].base != 0)) { - p_dev->io.BasePort1 = cf->io.win[0].base; - p_dev->io.IOAddrLines = ((*try & 0x1) == 0) ? - 16 : cf->io.flags & CISTPL_IO_LINES_MASK; - if (!pcmcia_request_io(p_dev, &p_dev->io)) + p_dev->resource[0]->start = cf->io.win[0].base; + if (!pcmcia_request_io(p_dev)) return 0; } return -EINVAL; @@ -449,9 +447,9 @@ static int simple_config_check_notpicky(struct pcmcia_device *p_dev, if ((cf->io.nwin > 0) && ((cf->io.flags & CISTPL_IO_LINES_MASK) <= 3)) { for (j = 0; j < 5; j++) { - p_dev->io.BasePort1 = base[j]; - p_dev->io.IOAddrLines = base[j] ? 16 : 3; - if (!pcmcia_request_io(p_dev, &p_dev->io)) + p_dev->resource[0]->start = base[j]; + p_dev->io_lines = base[j] ? 16 : 3; + if (!pcmcia_request_io(p_dev)) return 0; } } @@ -466,13 +464,13 @@ static int simple_config(struct pcmcia_device *link) /* If the card is already configured, look up the port and irq */ if (link->function_config) { unsigned int port = 0; - if ((link->io.BasePort2 != 0) && - (link->io.NumPorts2 == 8)) { - port = link->io.BasePort2; + if ((link->resource[1]->end != 0) && + (resource_size(link->resource[1]) == 8)) { + port = link->resource[1]->end; info->slave = 1; } else if ((info->manfid == MANFID_OSITECH) && - (link->io.NumPorts1 == 0x40)) { - port = link->io.BasePort1 + 0x28; + (resource_size(link->resource[0]) == 0x40)) { + port = link->resource[0]->start + 0x28; info->slave = 1; } if (info->slave) { @@ -510,7 +508,7 @@ found_port: i = pcmcia_request_configuration(link, &link->conf); if (i != 0) return -1; - return setup_serial(link, info, link->io.BasePort1, link->irq); + return setup_serial(link, info, link->resource[0]->start, link->irq); } static int multi_config_check(struct pcmcia_device *p_dev, @@ -524,10 +522,10 @@ static int multi_config_check(struct pcmcia_device *p_dev, /* The quad port cards have bad CIS's, so just look for a window larger than 8 ports and assume it will be right */ if ((cf->io.nwin == 1) && (cf->io.win[0].len > 8)) { - p_dev->io.BasePort1 = cf->io.win[0].base; - p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK; - if (!pcmcia_request_io(p_dev, &p_dev->io)) { - *base2 = p_dev->io.BasePort1 + 8; + p_dev->resource[0]->start = cf->io.win[0].base; + p_dev->io_lines = cf->io.flags & CISTPL_IO_LINES_MASK; + if (!pcmcia_request_io(p_dev)) { + *base2 = p_dev->resource[0]->start + 8; return 0; } } @@ -543,11 +541,11 @@ static int multi_config_check_notpicky(struct pcmcia_device *p_dev, int *base2 = priv_data; if (cf->io.nwin == 2) { - p_dev->io.BasePort1 = cf->io.win[0].base; - p_dev->io.BasePort2 = cf->io.win[1].base; - p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK; - if (!pcmcia_request_io(p_dev, &p_dev->io)) { - *base2 = p_dev->io.BasePort2; + p_dev->resource[0]->start = cf->io.win[0].base; + p_dev->resource[1]->start = cf->io.win[1].base; + p_dev->io_lines = cf->io.flags & CISTPL_IO_LINES_MASK; + if (!pcmcia_request_io(p_dev)) { + *base2 = p_dev->resource[1]->start; return 0; } } @@ -560,10 +558,10 @@ static int multi_config(struct pcmcia_device *link) int i, base2 = 0; /* First, look for a generic full-sized window */ - link->io.NumPorts1 = info->multi * 8; + link->resource[0]->end = info->multi * 8; if (pcmcia_loop_config(link, multi_config_check, &base2)) { /* If that didn't work, look for two windows */ - link->io.NumPorts1 = link->io.NumPorts2 = 8; + link->resource[0]->end = link->resource[1]->end = 8; info->multi = 2; if (pcmcia_loop_config(link, multi_config_check_notpicky, &base2)) { @@ -599,9 +597,9 @@ static int multi_config(struct pcmcia_device *link) link->conf.ConfigIndex == 3) { err = setup_serial(link, info, base2, link->irq); - base2 = link->io.BasePort1; + base2 = link->resource[0]->start;; } else { - err = setup_serial(link, info, link->io.BasePort1, + err = setup_serial(link, info, link->resource[0]->start, link->irq); } info->c950ctrl = base2; @@ -616,7 +614,7 @@ static int multi_config(struct pcmcia_device *link) return 0; } - setup_serial(link, info, link->io.BasePort1, link->irq); + setup_serial(link, info, link->resource[0]->start, link->irq); for (i = 0; i < info->multi - 1; i++) setup_serial(link, info, base2 + (8 * i), link->irq); diff --git a/drivers/serial/sh-sci.c b/drivers/serial/sh-sci.c index 5f90fcd7d10..c291b3add1d 100644 --- a/drivers/serial/sh-sci.c +++ b/drivers/serial/sh-sci.c @@ -346,6 +346,27 @@ static int scif_rxfill(struct uart_port *port) return sci_in(port, SCFDR) & SCIF2_RFDC_MASK; } } +#elif defined(CONFIG_ARCH_SH7372) +static int scif_txfill(struct uart_port *port) +{ + if (port->type == PORT_SCIFA) + return sci_in(port, SCFDR) >> 8; + else + return sci_in(port, SCTFDR); +} + +static int scif_txroom(struct uart_port *port) +{ + return port->fifosize - scif_txfill(port); +} + +static int scif_rxfill(struct uart_port *port) +{ + if (port->type == PORT_SCIFA) + return sci_in(port, SCFDR) & SCIF_RFDC_MASK; + else + return sci_in(port, SCRFDR); +} #else static int scif_txfill(struct uart_port *port) { @@ -683,7 +704,7 @@ static irqreturn_t sci_rx_interrupt(int irq, void *ptr) u16 ssr = sci_in(port, SCxSR); /* Disable future Rx interrupts */ - if (port->type == PORT_SCIFA) { + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { disable_irq_nosync(irq); scr |= 0x4000; } else { @@ -928,7 +949,7 @@ static void sci_dma_tx_complete(void *arg) if (!uart_circ_empty(xmit)) { schedule_work(&s->work_tx); - } else if (port->type == PORT_SCIFA) { + } else if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { u16 ctrl = sci_in(port, SCSCR); sci_out(port, SCSCR, ctrl & ~SCI_CTRL_FLAGS_TIE); } @@ -1184,7 +1205,7 @@ static void sci_start_tx(struct uart_port *port) unsigned short ctrl; #ifdef CONFIG_SERIAL_SH_SCI_DMA - if (port->type == PORT_SCIFA) { + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { u16 new, scr = sci_in(port, SCSCR); if (s->chan_tx) new = scr | 0x8000; @@ -1197,7 +1218,7 @@ static void sci_start_tx(struct uart_port *port) s->cookie_tx < 0) schedule_work(&s->work_tx); #endif - if (!s->chan_tx || port->type == PORT_SCIFA) { + if (!s->chan_tx || port->type == PORT_SCIFA || port->type == PORT_SCIFB) { /* Set TIE (Transmit Interrupt Enable) bit in SCSCR */ ctrl = sci_in(port, SCSCR); sci_out(port, SCSCR, ctrl | SCI_CTRL_FLAGS_TIE); @@ -1210,7 +1231,7 @@ static void sci_stop_tx(struct uart_port *port) /* Clear TIE (Transmit Interrupt Enable) bit in SCSCR */ ctrl = sci_in(port, SCSCR); - if (port->type == PORT_SCIFA) + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) ctrl &= ~0x8000; ctrl &= ~SCI_CTRL_FLAGS_TIE; sci_out(port, SCSCR, ctrl); @@ -1222,7 +1243,7 @@ static void sci_start_rx(struct uart_port *port) /* Set RIE (Receive Interrupt Enable) bit in SCSCR */ ctrl |= sci_in(port, SCSCR); - if (port->type == PORT_SCIFA) + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) ctrl &= ~0x4000; sci_out(port, SCSCR, ctrl); } @@ -1233,7 +1254,7 @@ static void sci_stop_rx(struct uart_port *port) /* Clear RIE (Receive Interrupt Enable) bit in SCSCR */ ctrl = sci_in(port, SCSCR); - if (port->type == PORT_SCIFA) + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) ctrl &= ~0x4000; ctrl &= ~(SCI_CTRL_FLAGS_RIE | SCI_CTRL_FLAGS_REIE); sci_out(port, SCSCR, ctrl); @@ -1271,7 +1292,7 @@ static void rx_timer_fn(unsigned long arg) struct uart_port *port = &s->port; u16 scr = sci_in(port, SCSCR); - if (port->type == PORT_SCIFA) { + if (port->type == PORT_SCIFA || port->type == PORT_SCIFB) { scr &= ~0x4000; enable_irq(s->irqs[1]); } @@ -1524,6 +1545,8 @@ static const char *sci_type(struct uart_port *port) return "scif"; case PORT_SCIFA: return "scifa"; + case PORT_SCIFB: + return "scifb"; } return NULL; @@ -1612,6 +1635,9 @@ static int __devinit sci_init_single(struct platform_device *dev, port->line = index; switch (p->type) { + case PORT_SCIFB: + port->fifosize = 256; + break; case PORT_SCIFA: port->fifosize = 64; break; diff --git a/drivers/serial/sh-sci.h b/drivers/serial/sh-sci.h index f70c49f915f..9b52f77a930 100644 --- a/drivers/serial/sh-sci.h +++ b/drivers/serial/sh-sci.h @@ -322,7 +322,7 @@ #define CPU_SCIx_FNS(name, sci_offset, sci_size, scif_offset, scif_size)\ static inline unsigned int sci_##name##_in(struct uart_port *port) \ { \ - if (port->type == PORT_SCIF) { \ + if (port->type == PORT_SCIF || port->type == PORT_SCIFB) { \ SCI_IN(scif_size, scif_offset) \ } else { /* PORT_SCI or PORT_SCIFA */ \ SCI_IN(sci_size, sci_offset); \ @@ -330,7 +330,7 @@ } \ static inline void sci_##name##_out(struct uart_port *port, unsigned int value) \ { \ - if (port->type == PORT_SCIF) { \ + if (port->type == PORT_SCIF || port->type == PORT_SCIFB) { \ SCI_OUT(scif_size, scif_offset, value) \ } else { /* PORT_SCI or PORT_SCIFA */ \ SCI_OUT(sci_size, sci_offset, value); \ @@ -384,8 +384,12 @@ defined(CONFIG_CPU_SUBTYPE_SH7720) || \ defined(CONFIG_CPU_SUBTYPE_SH7721) || \ defined(CONFIG_ARCH_SH7367) || \ - defined(CONFIG_ARCH_SH7377) || \ - defined(CONFIG_ARCH_SH7372) + defined(CONFIG_ARCH_SH7377) +#define SCIF_FNS(name, scif_offset, scif_size) \ + CPU_SCIF_FNS(name, scif_offset, scif_size) +#elif defined(CONFIG_ARCH_SH7372) +#define SCIx_FNS(name, sh4_scifa_offset, sh4_scifa_size, sh4_scifb_offset, sh4_scifb_size) \ + CPU_SCIx_FNS(name, sh4_scifa_offset, sh4_scifa_size, sh4_scifb_offset, sh4_scifb_size) #define SCIF_FNS(name, scif_offset, scif_size) \ CPU_SCIF_FNS(name, scif_offset, scif_size) #else @@ -422,8 +426,7 @@ defined(CONFIG_CPU_SUBTYPE_SH7720) || \ defined(CONFIG_CPU_SUBTYPE_SH7721) || \ defined(CONFIG_ARCH_SH7367) || \ - defined(CONFIG_ARCH_SH7377) || \ - defined(CONFIG_ARCH_SH7372) + defined(CONFIG_ARCH_SH7377) SCIF_FNS(SCSMR, 0x00, 16) SCIF_FNS(SCBRR, 0x04, 8) @@ -436,6 +439,20 @@ SCIF_FNS(SCFDR, 0x1c, 16) SCIF_FNS(SCxTDR, 0x20, 8) SCIF_FNS(SCxRDR, 0x24, 8) SCIF_FNS(SCLSR, 0x00, 0) +#elif defined(CONFIG_ARCH_SH7372) +SCIF_FNS(SCSMR, 0x00, 16) +SCIF_FNS(SCBRR, 0x04, 8) +SCIF_FNS(SCSCR, 0x08, 16) +SCIF_FNS(SCTDSR, 0x0c, 16) +SCIF_FNS(SCFER, 0x10, 16) +SCIF_FNS(SCxSR, 0x14, 16) +SCIF_FNS(SCFCR, 0x18, 16) +SCIF_FNS(SCFDR, 0x1c, 16) +SCIF_FNS(SCTFDR, 0x38, 16) +SCIF_FNS(SCRFDR, 0x3c, 16) +SCIx_FNS(SCxTDR, 0x20, 8, 0x40, 8) +SCIx_FNS(SCxRDR, 0x24, 8, 0x60, 8) +SCIF_FNS(SCLSR, 0x00, 0) #elif defined(CONFIG_CPU_SUBTYPE_SH7723) ||\ defined(CONFIG_CPU_SUBTYPE_SH7724) SCIx_FNS(SCSMR, 0x00, 16, 0x00, 16) diff --git a/drivers/serial/suncore.c b/drivers/serial/suncore.c index 544f2e25d0e..6381a0282ee 100644 --- a/drivers/serial/suncore.c +++ b/drivers/serial/suncore.c @@ -55,7 +55,12 @@ EXPORT_SYMBOL(sunserial_unregister_minors); int sunserial_console_match(struct console *con, struct device_node *dp, struct uart_driver *drv, int line, bool ignore_line) { - if (!con || of_console_device != dp) + if (!con) + return 0; + + drv->cons = con; + + if (of_console_device != dp) return 0; if (!ignore_line) { @@ -69,12 +74,10 @@ int sunserial_console_match(struct console *con, struct device_node *dp, return 0; } - con->index = line; - drv->cons = con; - - if (!console_set_on_cmdline) + if (!console_set_on_cmdline) { + con->index = line; add_preferred_console(con->name, line, NULL); - + } return 1; } EXPORT_SYMBOL(sunserial_console_match); diff --git a/drivers/serial/sunhv.c b/drivers/serial/sunhv.c index 890f9174296..c9014868297 100644 --- a/drivers/serial/sunhv.c +++ b/drivers/serial/sunhv.c @@ -519,13 +519,13 @@ static struct console sunhv_console = { .data = &sunhv_reg, }; -static int __devinit hv_probe(struct of_device *op, const struct of_device_id *match) +static int __devinit hv_probe(struct platform_device *op, const struct of_device_id *match) { struct uart_port *port; unsigned long minor; int err; - if (op->irqs[0] == 0xffffffff) + if (op->archdata.irqs[0] == 0xffffffff) return -ENODEV; port = kzalloc(sizeof(struct uart_port), GFP_KERNEL); @@ -557,7 +557,7 @@ static int __devinit hv_probe(struct of_device *op, const struct of_device_id *m port->membase = (unsigned char __iomem *) __pa(port); - port->irq = op->irqs[0]; + port->irq = op->archdata.irqs[0]; port->dev = &op->dev; @@ -598,7 +598,7 @@ out_free_port: return err; } -static int __devexit hv_remove(struct of_device *dev) +static int __devexit hv_remove(struct platform_device *dev) { struct uart_port *port = dev_get_drvdata(&dev->dev); @@ -644,12 +644,12 @@ static int __init sunhv_init(void) if (tlb_type != hypervisor) return -ENODEV; - return of_register_driver(&hv_driver, &of_bus_type); + return of_register_platform_driver(&hv_driver); } static void __exit sunhv_exit(void) { - of_unregister_driver(&hv_driver); + of_unregister_platform_driver(&hv_driver); } module_init(sunhv_init); diff --git a/drivers/serial/sunsab.c b/drivers/serial/sunsab.c index 5e81bc6b48b..5b246b18f42 100644 --- a/drivers/serial/sunsab.c +++ b/drivers/serial/sunsab.c @@ -883,7 +883,7 @@ static int sunsab_console_setup(struct console *con, char *options) printk("Console: ttyS%d (SAB82532)\n", (sunsab_reg.minor - 64) + con->index); - sunserial_console_termios(con, to_of_device(up->port.dev)->dev.of_node); + sunserial_console_termios(con, up->port.dev->of_node); switch (con->cflag & CBAUD) { case B150: baud = 150; break; @@ -954,7 +954,7 @@ static inline struct console *SUNSAB_CONSOLE(void) #endif static int __devinit sunsab_init_one(struct uart_sunsab_port *up, - struct of_device *op, + struct platform_device *op, unsigned long offset, int line) { @@ -969,7 +969,7 @@ static int __devinit sunsab_init_one(struct uart_sunsab_port *up, return -ENOMEM; up->regs = (union sab82532_async_regs __iomem *) up->port.membase; - up->port.irq = op->irqs[0]; + up->port.irq = op->archdata.irqs[0]; up->port.fifosize = SAB82532_XMIT_FIFO_SIZE; up->port.iotype = UPIO_MEM; @@ -1006,7 +1006,7 @@ static int __devinit sunsab_init_one(struct uart_sunsab_port *up, return 0; } -static int __devinit sab_probe(struct of_device *op, const struct of_device_id *match) +static int __devinit sab_probe(struct platform_device *op, const struct of_device_id *match) { static int inst; struct uart_sunsab_port *up; @@ -1062,7 +1062,7 @@ out: return err; } -static int __devexit sab_remove(struct of_device *op) +static int __devexit sab_remove(struct platform_device *op) { struct uart_sunsab_port *up = dev_get_drvdata(&op->dev); @@ -1130,12 +1130,12 @@ static int __init sunsab_init(void) } } - return of_register_driver(&sab_driver, &of_bus_type); + return of_register_platform_driver(&sab_driver); } static void __exit sunsab_exit(void) { - of_unregister_driver(&sab_driver); + of_unregister_platform_driver(&sab_driver); if (sunsab_reg.nr) { sunserial_unregister_minors(&sunsab_reg, sunsab_reg.nr); } diff --git a/drivers/serial/sunsu.c b/drivers/serial/sunsu.c index ffbf4553f66..551ebfe3ccb 100644 --- a/drivers/serial/sunsu.c +++ b/drivers/serial/sunsu.c @@ -1200,7 +1200,7 @@ static int __devinit sunsu_kbd_ms_init(struct uart_sunsu_port *up) return -ENODEV; printk("%s: %s port at %llx, irq %u\n", - to_of_device(up->port.dev)->dev.of_node->full_name, + up->port.dev->of_node->full_name, (up->su_type == SU_PORT_KBD) ? "Keyboard" : "Mouse", (unsigned long long) up->port.mapbase, up->port.irq); @@ -1352,7 +1352,7 @@ static int __init sunsu_console_setup(struct console *co, char *options) spin_lock_init(&port->lock); /* Get firmware console settings. */ - sunserial_console_termios(co, to_of_device(port->dev)->dev.of_node); + sunserial_console_termios(co, port->dev->of_node); memset(&termios, 0, sizeof(struct ktermios)); termios.c_cflag = co->cflag; @@ -1406,7 +1406,7 @@ static enum su_type __devinit su_get_type(struct device_node *dp) return SU_PORT_PORT; } -static int __devinit su_probe(struct of_device *op, const struct of_device_id *match) +static int __devinit su_probe(struct platform_device *op, const struct of_device_id *match) { static int inst; struct device_node *dp = op->dev.of_node; @@ -1443,7 +1443,7 @@ static int __devinit su_probe(struct of_device *op, const struct of_device_id *m return -ENOMEM; } - up->port.irq = op->irqs[0]; + up->port.irq = op->archdata.irqs[0]; up->port.dev = &op->dev; @@ -1497,7 +1497,7 @@ out_unmap: return err; } -static int __devexit su_remove(struct of_device *op) +static int __devexit su_remove(struct platform_device *op) { struct uart_sunsu_port *up = dev_get_drvdata(&op->dev); bool kbdms = false; @@ -1586,7 +1586,7 @@ static int __init sunsu_init(void) return err; } - err = of_register_driver(&su_driver, &of_bus_type); + err = of_register_platform_driver(&su_driver); if (err && num_uart) sunserial_unregister_minors(&sunsu_reg, num_uart); diff --git a/drivers/serial/sunzilog.c b/drivers/serial/sunzilog.c index f9a24f4ebb3..c1967ac1c07 100644 --- a/drivers/serial/sunzilog.c +++ b/drivers/serial/sunzilog.c @@ -1230,7 +1230,7 @@ static int __init sunzilog_console_setup(struct console *con, char *options) (sunzilog_reg.minor - 64) + con->index, con->index); /* Get firmware console settings. */ - sunserial_console_termios(con, to_of_device(up->port.dev)->dev.of_node); + sunserial_console_termios(con, up->port.dev->of_node); /* Firmware console speed is limited to 150-->38400 baud so * this hackish cflag thing is OK. @@ -1399,7 +1399,7 @@ static void __devinit sunzilog_init_hw(struct uart_sunzilog_port *up) static int zilog_irq = -1; -static int __devinit zs_probe(struct of_device *op, const struct of_device_id *match) +static int __devinit zs_probe(struct platform_device *op, const struct of_device_id *match) { static int kbm_inst, uart_inst; int inst; @@ -1426,7 +1426,7 @@ static int __devinit zs_probe(struct of_device *op, const struct of_device_id *m rp = sunzilog_chip_regs[inst]; if (zilog_irq == -1) - zilog_irq = op->irqs[0]; + zilog_irq = op->archdata.irqs[0]; up = &sunzilog_port_table[inst * 2]; @@ -1434,7 +1434,7 @@ static int __devinit zs_probe(struct of_device *op, const struct of_device_id *m up[0].port.mapbase = op->resource[0].start + 0x00; up[0].port.membase = (void __iomem *) &rp->channelA; up[0].port.iotype = UPIO_MEM; - up[0].port.irq = op->irqs[0]; + up[0].port.irq = op->archdata.irqs[0]; up[0].port.uartclk = ZS_CLOCK; up[0].port.fifosize = 1; up[0].port.ops = &sunzilog_pops; @@ -1451,7 +1451,7 @@ static int __devinit zs_probe(struct of_device *op, const struct of_device_id *m up[1].port.mapbase = op->resource[0].start + 0x04; up[1].port.membase = (void __iomem *) &rp->channelB; up[1].port.iotype = UPIO_MEM; - up[1].port.irq = op->irqs[0]; + up[1].port.irq = op->archdata.irqs[0]; up[1].port.uartclk = ZS_CLOCK; up[1].port.fifosize = 1; up[1].port.ops = &sunzilog_pops; @@ -1492,12 +1492,12 @@ static int __devinit zs_probe(struct of_device *op, const struct of_device_id *m "is a %s\n", dev_name(&op->dev), (unsigned long long) up[0].port.mapbase, - op->irqs[0], sunzilog_type(&up[0].port)); + op->archdata.irqs[0], sunzilog_type(&up[0].port)); printk(KERN_INFO "%s: Mouse at MMIO 0x%llx (irq = %d) " "is a %s\n", dev_name(&op->dev), (unsigned long long) up[1].port.mapbase, - op->irqs[0], sunzilog_type(&up[1].port)); + op->archdata.irqs[0], sunzilog_type(&up[1].port)); kbm_inst++; } @@ -1516,7 +1516,7 @@ static void __devexit zs_remove_one(struct uart_sunzilog_port *up) uart_remove_one_port(&sunzilog_reg, &up->port); } -static int __devexit zs_remove(struct of_device *op) +static int __devexit zs_remove(struct platform_device *op) { struct uart_sunzilog_port *up = dev_get_drvdata(&op->dev); struct zilog_layout __iomem *regs; @@ -1576,7 +1576,7 @@ static int __init sunzilog_init(void) goto out_free_tables; } - err = of_register_driver(&zs_driver, &of_bus_type); + err = of_register_platform_driver(&zs_driver); if (err) goto out_unregister_uart; @@ -1604,7 +1604,7 @@ out: return err; out_unregister_driver: - of_unregister_driver(&zs_driver); + of_unregister_platform_driver(&zs_driver); out_unregister_uart: if (num_sunzilog) { @@ -1619,7 +1619,7 @@ out_free_tables: static void __exit sunzilog_exit(void) { - of_unregister_driver(&zs_driver); + of_unregister_platform_driver(&zs_driver); if (zilog_irq != -1) { struct uart_sunzilog_port *up = sunzilog_irq_chain; diff --git a/drivers/serial/timbuart.c b/drivers/serial/timbuart.c index 67ca642713b..1f36b7eb735 100644 --- a/drivers/serial/timbuart.c +++ b/drivers/serial/timbuart.c @@ -423,7 +423,7 @@ static struct uart_driver timbuart_driver = { .nr = 1 }; -static int timbuart_probe(struct platform_device *dev) +static int __devinit timbuart_probe(struct platform_device *dev) { int err, irq; struct timbuart_port *uart; @@ -489,7 +489,7 @@ err_mem: return err; } -static int timbuart_remove(struct platform_device *dev) +static int __devexit timbuart_remove(struct platform_device *dev) { struct timbuart_port *uart = platform_get_drvdata(dev); @@ -507,7 +507,7 @@ static struct platform_driver timbuart_platform_driver = { .owner = THIS_MODULE, }, .probe = timbuart_probe, - .remove = timbuart_remove, + .remove = __devexit_p(timbuart_remove), }; /*--------------------------------------------------------------------------*/ diff --git a/drivers/serial/uartlite.c b/drivers/serial/uartlite.c index 8acccd56437..9b03d7b3e45 100644 --- a/drivers/serial/uartlite.c +++ b/drivers/serial/uartlite.c @@ -21,6 +21,7 @@ #include <asm/io.h> #if defined(CONFIG_OF) && (defined(CONFIG_PPC32) || defined(CONFIG_MICROBLAZE)) #include <linux/of.h> +#include <linux/of_address.h> #include <linux/of_device.h> #include <linux/of_platform.h> @@ -583,7 +584,7 @@ static struct platform_driver ulite_platform_driver = { */ #if defined(CONFIG_OF) && (defined(CONFIG_PPC32) || defined(CONFIG_MICROBLAZE)) static int __devinit -ulite_of_probe(struct of_device *op, const struct of_device_id *match) +ulite_of_probe(struct platform_device *op, const struct of_device_id *match) { struct resource res; const unsigned int *id; @@ -604,7 +605,7 @@ ulite_of_probe(struct of_device *op, const struct of_device_id *match) return ulite_assign(&op->dev, id ? *id : -1, res.start, irq); } -static int __devexit ulite_of_remove(struct of_device *op) +static int __devexit ulite_of_remove(struct platform_device *op) { return ulite_release(&op->dev); } diff --git a/drivers/serial/ucc_uart.c b/drivers/serial/ucc_uart.c index 907b06f5c44..3f4848e2174 100644 --- a/drivers/serial/ucc_uart.c +++ b/drivers/serial/ucc_uart.c @@ -1194,7 +1194,7 @@ static void uart_firmware_cont(const struct firmware *fw, void *context) release_firmware(fw); } -static int ucc_uart_probe(struct of_device *ofdev, +static int ucc_uart_probe(struct platform_device *ofdev, const struct of_device_id *match) { struct device_node *np = ofdev->dev.of_node; @@ -1462,7 +1462,7 @@ static int ucc_uart_probe(struct of_device *ofdev, return 0; } -static int ucc_uart_remove(struct of_device *ofdev) +static int ucc_uart_remove(struct platform_device *ofdev) { struct uart_qe_port *qe_port = dev_get_drvdata(&ofdev->dev); |