diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/Kconfig | 7 | ||||
| -rw-r--r-- | drivers/serial/mrst_max3110.c | 55 |
2 files changed, 28 insertions, 34 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 12900f7083b..ba4b390299d 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -717,13 +717,6 @@ config SERIAL_MRST_MAX3110 the Intel Moorestown platform. On other systems use the max3100 driver. -config MRST_MAX3110_IRQ - boolean "Enable GPIO IRQ for Max3110 over Moorestown" - default n - depends on SERIAL_MRST_MAX3110 && GPIO_LANGWELL - help - This has to be enabled after Moorestown GPIO driver is loaded - config SERIAL_MFD_HSU tristate "Medfield High Speed UART support" depends on PCI diff --git a/drivers/serial/mrst_max3110.c b/drivers/serial/mrst_max3110.c index af8db27f9e8..b62857bf2fd 100644 --- a/drivers/serial/mrst_max3110.c +++ b/drivers/serial/mrst_max3110.c @@ -447,7 +447,6 @@ static int max3110_main_thread(void *_max) return ret; } -#ifdef CONFIG_MRST_MAX3110_IRQ static irqreturn_t serial_m3110_irq(int irq, void *dev_id) { struct uart_max3110 *max = dev_id; @@ -459,7 +458,7 @@ static irqreturn_t serial_m3110_irq(int irq, void *dev_id) return IRQ_HANDLED; } -#else + /* if don't use RX IRQ, then need a thread to polling read */ static int max3110_read_thread(void *_max) { @@ -482,7 +481,6 @@ static int max3110_read_thread(void *_max) return 0; } -#endif static int serial_m3110_startup(struct uart_port *port) { @@ -505,34 +503,38 @@ static int serial_m3110_startup(struct uart_port *port) /* as we use thread to handle tx/rx, need set low latency */ port->state->port.tty->low_latency = 1; -#ifdef CONFIG_MRST_MAX3110_IRQ - ret = request_irq(max->irq, serial_m3110_irq, + if (max->irq) { + max->read_thread = NULL; + ret = request_irq(max->irq, serial_m3110_irq, IRQ_TYPE_EDGE_FALLING, "max3110", max); - if (ret) - return ret; + if (ret) { + max->irq = 0; + pr_err(PR_FMT "unable to allocate IRQ, polling\n"); + } else { + /* Enable RX IRQ only */ + config |= WC_RXA_IRQ_ENABLE; + } + } - /* Enable RX IRQ only */ - config |= WC_RXA_IRQ_ENABLE; -#else - /* If IRQ is disabled, start a read thread for input data */ - max->read_thread = - kthread_run(max3110_read_thread, max, "max3110_read"); - if (IS_ERR(max->read_thread)) { - ret = PTR_ERR(max->read_thread); - max->read_thread = NULL; - pr_err(PR_FMT "Can't create read thread!"); - return ret; + if (max->irq == 0) { + /* If IRQ is disabled, start a read thread for input data */ + max->read_thread = + kthread_run(max3110_read_thread, max, "max3110_read"); + if (IS_ERR(max->read_thread)) { + ret = PTR_ERR(max->read_thread); + max->read_thread = NULL; + pr_err(PR_FMT "Can't create read thread!\n"); + return ret; + } } -#endif ret = max3110_out(max, config); if (ret) { -#ifdef CONFIG_MRST_MAX3110_IRQ - free_irq(max->irq, max); -#else - kthread_stop(max->read_thread); + if (max->irq) + free_irq(max->irq, max); + if (max->read_thread) + kthread_stop(max->read_thread); max->read_thread = NULL; -#endif return ret; } @@ -551,9 +553,8 @@ static void serial_m3110_shutdown(struct uart_port *port) max->read_thread = NULL; } -#ifdef CONFIG_MRST_MAX3110_IRQ - free_irq(max->irq, max); -#endif + if (max->irq) + free_irq(max->irq, max); /* Disable interrupts from this port */ config = WC_TAG | WC_SW_SHDI; |