diff options
Diffstat (limited to 'drivers/serial')
| -rw-r--r-- | drivers/serial/8250_hp300.c | 1 | ||||
| -rw-r--r-- | drivers/serial/Kconfig | 58 | ||||
| -rw-r--r-- | drivers/serial/Makefile | 2 | ||||
| -rw-r--r-- | drivers/serial/amba-pl011.c | 3 | ||||
| -rw-r--r-- | drivers/serial/cpm_uart/cpm_uart_core.c | 2 | ||||
| -rw-r--r-- | drivers/serial/of_serial.c | 33 | ||||
| -rw-r--r-- | drivers/serial/sb1250-duart.c | 972 | ||||
| -rw-r--r-- | drivers/serial/sunhv.c | 12 | ||||
| -rw-r--r-- | drivers/serial/zs.c | 1287 | ||||
| -rw-r--r-- | drivers/serial/zs.h | 284 |
10 files changed, 2633 insertions, 21 deletions
diff --git a/drivers/serial/8250_hp300.c b/drivers/serial/8250_hp300.c index 53e81a44c1a..2cf0953fe0e 100644 --- a/drivers/serial/8250_hp300.c +++ b/drivers/serial/8250_hp300.c @@ -11,6 +11,7 @@ #include <linux/kernel.h> #include <linux/serial.h> #include <linux/serial_core.h> +#include <linux/serial_8250.h> #include <linux/delay.h> #include <linux/dio.h> #include <linux/console.h> diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index cab42cbd920..18f62970644 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -338,6 +338,34 @@ config SERIAL_AMBA_PL011_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) +config SERIAL_SB1250_DUART + tristate "BCM1xxx on-chip DUART serial support" + depends on SIBYTE_SB1xxx_SOC=y + select SERIAL_CORE + default y + ---help--- + Support for the asynchronous serial interface (DUART) included in + the BCM1250 and derived System-On-a-Chip (SOC) devices. Note that + the letter D in DUART stands for "dual", which is how the device + is implemented. Depending on the SOC configuration there may be + one or more DUARTs available of which all are handled. + + If unsure, say Y. To compile this driver as a module, choose M here: + the module will be called sb1250-duart. + +config SERIAL_SB1250_DUART_CONSOLE + bool "Support for console on a BCM1xxx DUART serial port" + depends on SERIAL_SB1250_DUART=y + select SERIAL_CORE_CONSOLE + default y + ---help--- + If you say Y here, it will be possible to use a serial port as the + system console (the system console is the device which receives all + kernel messages and warnings and which allows logins in single user + mode). + + If unsure, say Y. + config SERIAL_ATMEL bool "AT91 / AT32 on-chip serial port support" depends on (ARM && ARCH_AT91) || AVR32 @@ -458,6 +486,36 @@ config SERIAL_DZ_CONSOLE If unsure, say Y. +config SERIAL_ZS + tristate "DECstation Z85C30 serial support" + depends on MACH_DECSTATION + select SERIAL_CORE + default y + ---help--- + Support for the Zilog 85C350 serial communications controller used + for serial ports in newer DECstation systems. These include the + DECsystem 5900 and all models of the DECstation and DECsystem 5000 + systems except from model 200. + + If unsure, say Y. To compile this driver as a module, choose M here: + the module will be called zs. + +config SERIAL_ZS_CONSOLE + bool "Support for console on a DECstation Z85C30 serial port" + depends on SERIAL_ZS=y + select SERIAL_CORE_CONSOLE + default y + ---help--- + If you say Y here, it will be possible to use a serial port as the + system console (the system console is the device which receives all + kernel messages and warnings and which allows logins in single user + mode). + + Note that the firmware uses ttyS1 as the serial console on the + Maxine and ttyS3 on the others using this driver. + + If unsure, say Y. + config SERIAL_21285 tristate "DC21285 serial port support" depends on ARM && FOOTBRIDGE diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile index 08ad0d97818..af6377d480d 100644 --- a/drivers/serial/Makefile +++ b/drivers/serial/Makefile @@ -43,6 +43,7 @@ obj-$(CONFIG_V850E_UART) += v850e_uart.o obj-$(CONFIG_SERIAL_PMACZILOG) += pmac_zilog.o obj-$(CONFIG_SERIAL_LH7A40X) += serial_lh7a40x.o obj-$(CONFIG_SERIAL_DZ) += dz.o +obj-$(CONFIG_SERIAL_ZS) += zs.o obj-$(CONFIG_SERIAL_SH_SCI) += sh-sci.o obj-$(CONFIG_SERIAL_SGI_L1_CONSOLE) += sn_console.o obj-$(CONFIG_SERIAL_CPM) += cpm_uart/ @@ -51,6 +52,7 @@ obj-$(CONFIG_SERIAL_MPC52xx) += mpc52xx_uart.o obj-$(CONFIG_SERIAL_ICOM) += icom.o obj-$(CONFIG_SERIAL_M32R_SIO) += m32r_sio.o obj-$(CONFIG_SERIAL_MPSC) += mpsc.o +obj-$(CONFIG_SERIAL_SB1250_DUART) += sb1250-duart.o obj-$(CONFIG_ETRAX_SERIAL) += crisv10.o obj-$(CONFIG_SERIAL_JSM) += jsm/ obj-$(CONFIG_SERIAL_TXX9) += serial_txx9.o diff --git a/drivers/serial/amba-pl011.c b/drivers/serial/amba-pl011.c index 954073c6ce3..72229df9dc1 100644 --- a/drivers/serial/amba-pl011.c +++ b/drivers/serial/amba-pl011.c @@ -716,7 +716,7 @@ static int pl011_probe(struct amba_device *dev, void *id) goto out; } - uap = kmalloc(sizeof(struct uart_amba_port), GFP_KERNEL); + uap = kzalloc(sizeof(struct uart_amba_port), GFP_KERNEL); if (uap == NULL) { ret = -ENOMEM; goto out; @@ -728,7 +728,6 @@ static int pl011_probe(struct amba_device *dev, void *id) goto free; } - memset(uap, 0, sizeof(struct uart_amba_port)); uap->clk = clk_get(&dev->dev, "UARTCLK"); if (IS_ERR(uap->clk)) { ret = PTR_ERR(uap->clk); diff --git a/drivers/serial/cpm_uart/cpm_uart_core.c b/drivers/serial/cpm_uart/cpm_uart_core.c index b63ff8dd730..cefde58dbad 100644 --- a/drivers/serial/cpm_uart/cpm_uart_core.c +++ b/drivers/serial/cpm_uart/cpm_uart_core.c @@ -678,7 +678,7 @@ static int cpm_uart_tx_pump(struct uart_port *port) } bdp->cbd_datlen = count; bdp->cbd_sc |= BD_SC_READY; - __asm__("eieio"); + eieio(); /* Get next BD. */ if (bdp->cbd_sc & BD_SC_WRAP) bdp = pinfo->tx_bd_base; diff --git a/drivers/serial/of_serial.c b/drivers/serial/of_serial.c index 7ffdaeaf054..a64d8582199 100644 --- a/drivers/serial/of_serial.c +++ b/drivers/serial/of_serial.c @@ -17,6 +17,11 @@ #include <asm/of_platform.h> #include <asm/prom.h> +struct of_serial_info { + int type; + int line; +}; + /* * Fill a struct uart_port for a given device node */ @@ -62,6 +67,7 @@ static int __devinit of_platform_serial_setup(struct of_device *ofdev, static int __devinit of_platform_serial_probe(struct of_device *ofdev, const struct of_device_id *id) { + struct of_serial_info *info; struct uart_port port; int port_type; int ret; @@ -69,30 +75,35 @@ static int __devinit of_platform_serial_probe(struct of_device *ofdev, if (of_find_property(ofdev->node, "used-by-rtas", NULL)) return -EBUSY; + info = kmalloc(sizeof(*info), GFP_KERNEL); + if (info == NULL) + return -ENOMEM; + port_type = (unsigned long)id->data; ret = of_platform_serial_setup(ofdev, port_type, &port); if (ret) goto out; switch (port_type) { - case PORT_UNKNOWN: - dev_info(&ofdev->dev, "Unknown serial port found, " - "attempting to use 8250 driver\n"); - /* fallthrough */ case PORT_8250 ... PORT_MAX_8250: ret = serial8250_register_port(&port); break; default: /* need to add code for these */ + case PORT_UNKNOWN: + dev_info(&ofdev->dev, "Unknown serial port found, ignored\n"); ret = -ENODEV; break; } if (ret < 0) goto out; - ofdev->dev.driver_data = (void *)(unsigned long)ret; + info->type = port_type; + info->line = ret; + ofdev->dev.driver_data = info; return 0; out: + kfree(info); irq_dispose_mapping(port.irq); return ret; } @@ -102,8 +113,16 @@ out: */ static int of_platform_serial_remove(struct of_device *ofdev) { - int line = (unsigned long)ofdev->dev.driver_data; - serial8250_unregister_port(line); + struct of_serial_info *info = ofdev->dev.driver_data; + switch (info->type) { + case PORT_8250 ... PORT_MAX_8250: + serial8250_unregister_port(info->line); + break; + default: + /* need to add code for these */ + break; + } + kfree(info); return 0; } diff --git a/drivers/serial/sb1250-duart.c b/drivers/serial/sb1250-duart.c new file mode 100644 index 00000000000..1d9d7285172 --- /dev/null +++ b/drivers/serial/sb1250-duart.c @@ -0,0 +1,972 @@ +/* + * drivers/serial/sb1250-duart.c + * + * Support for the asynchronous serial interface (DUART) included + * in the BCM1250 and derived System-On-a-Chip (SOC) devices. + * + * Copyright (c) 2007 Maciej W. Rozycki + * + * Derived from drivers/char/sb1250_duart.c for which the following + * copyright applies: + * + * Copyright (c) 2000, 2001, 2002, 2003, 2004 Broadcom Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * References: + * + * "BCM1250/BCM1125/BCM1125H User Manual", Broadcom Corporation + */ + +#if defined(CONFIG_SERIAL_SB1250_DUART_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/ioport.h> +#include <linux/kernel.h> +#include <linux/major.h> +#include <linux/serial.h> +#include <linux/serial_core.h> +#include <linux/spinlock.h> +#include <linux/sysrq.h> +#include <linux/tty.h> +#include <linux/types.h> + +#include <asm/atomic.h> +#include <asm/io.h> +#include <asm/war.h> + +#include <asm/sibyte/sb1250.h> +#include <asm/sibyte/sb1250_uart.h> +#include <asm/sibyte/swarm.h> + + +#if defined(CONFIG_SIBYTE_BCM1x55) || defined(CONFIG_SIBYTE_BCM1x80) +#include <asm/sibyte/bcm1480_regs.h> +#include <asm/sibyte/bcm1480_int.h> + +#define SBD_CHANREGS(line) A_BCM1480_DUART_CHANREG((line), 0) +#define SBD_CTRLREGS(line) A_BCM1480_DUART_CTRLREG((line), 0) +#define SBD_INT(line) (K_BCM1480_INT_UART_0 + (line)) + +#elif defined(CONFIG_SIBYTE_SB1250) || defined(CONFIG_SIBYTE_BCM112X) +#include <asm/sibyte/sb1250_regs.h> +#include <asm/sibyte/sb1250_int.h> + +#define SBD_CHANREGS(line) A_DUART_CHANREG((line), 0) +#define SBD_CTRLREGS(line) A_DUART_CTRLREG(0) +#define SBD_INT(line) (K_INT_UART_0 + (line)) + +#else +#error invalid SB1250 UART configuration + +#endif + + +MODULE_AUTHOR("Maciej W. Rozycki <macro@linux-mips.org>"); +MODULE_DESCRIPTION("BCM1xxx on-chip DUART serial driver"); +MODULE_LICENSE("GPL"); + + +#define DUART_MAX_CHIP 2 +#define DUART_MAX_SIDE 2 + +/* + * Per-port state. + */ +struct sbd_port { + struct sbd_duart *duart; + struct uart_port port; + unsigned char __iomem *memctrl; + int tx_stopped; + int initialised; +}; + +/* + * Per-DUART state for the shared register space. + */ +struct sbd_duart { + struct sbd_port sport[2]; + unsigned long mapctrl; + atomic_t map_guard; +}; + +#define to_sport(uport) container_of(uport, struct sbd_port, port) + +static struct sbd_duart sbd_duarts[DUART_MAX_CHIP]; + +#define __unused __attribute__((__unused__)) + + +/* + * Reading and writing SB1250 DUART registers. + * + * There are three register spaces: two per-channel ones and + * a shared one. We have to define accessors appropriately. + * All registers are 64-bit and all but the Baud Rate Clock + * registers only define 8 least significant bits. There is + * also a workaround to take into account. Raw accessors use + * the full register width, but cooked ones truncate it + * intentionally so that the rest of the driver does not care. + */ +static u64 __read_sbdchn(struct sbd_port *sport, int reg) +{ + void __iomem *csr = sport->port.membase + reg; + + return __raw_readq(csr); +} + +static u64 __read_sbdshr(struct sbd_port *sport, int reg) +{ + void __iomem *csr = sport->memctrl + reg; + + return __raw_readq(csr); +} + +static void __write_sbdchn(struct sbd_port *sport, int reg, u64 value) +{ + void __iomem *csr = sport->port.membase + reg; + + __raw_writeq(value, csr); +} + +static void __write_sbdshr(struct sbd_port *sport, int reg, u64 value) +{ + void __iomem *csr = sport->memctrl + reg; + + __raw_writeq(value, csr); +} + +/* + * In bug 1956, we get glitches that can mess up uart registers. This + * "read-mode-reg after any register access" is an accepted workaround. + */ +static void __war_sbd1956(struct sbd_port *sport) +{ + __read_sbdchn(sport, R_DUART_MODE_REG_1); + __read_sbdchn(sport, R_DUART_MODE_REG_2); +} + +static unsigned char read_sbdchn(struct sbd_port *sport, int reg) +{ + unsigned char retval; + + retval = __read_sbdchn(sport, reg); + if (SIBYTE_1956_WAR) + __war_sbd1956(sport); + return retval; +} + +static unsigned char read_sbdshr(struct sbd_port *sport, int reg) +{ + unsigned char retval; + + retval = __read_sbdshr(sport, reg); + if (SIBYTE_1956_WAR) + __war_sbd1956(sport); + return retval; +} + +static void write_sbdchn(struct sbd_port *sport, int reg, unsigned int value) +{ + __write_sbdchn(sport, reg, value); + if (SIBYTE_1956_WAR) + __war_sbd1956(sport); +} + +static void write_sbdshr(struct sbd_port *sport, int reg, unsigned int value) +{ + __write_sbdshr(sport, reg, value); + if (SIBYTE_1956_WAR) + __war_sbd1956(sport); +} + + +static int sbd_receive_ready(struct sbd_port *sport) +{ + return read_sbdchn(sport, R_DUART_STATUS) & M_DUART_RX_RDY; +} + +static int sbd_receive_drain(struct sbd_port *sport) +{ + int loops = 10000; + + while (sbd_receive_ready(sport) && loops--) + read_sbdchn(sport, R_DUART_RX_HOLD); + return loops; +} + +static int __unused sbd_transmit_ready(struct sbd_port *sport) +{ + return read_sbdchn(sport, R_DUART_STATUS) & M_DUART_TX_RDY; +} + +static int __unused sbd_transmit_drain(struct sbd_port *sport) +{ + int loops = 10000; + + while (!sbd_transmit_ready(sport) && loops--) + udelay(2); + return loops; +} + +static int sbd_transmit_empty(struct sbd_port *sport) +{ + return read_sbdchn(sport, R_DUART_STATUS) & M_DUART_TX_EMT; +} + +static int sbd_line_drain(struct sbd_port *sport) +{ + int loops = 10000; + + while (!sbd_transmit_empty(sport) && loops--) + udelay(2); + return loops; +} + + +static unsigned int sbd_tx_empty(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + + return sbd_transmit_empty(sport) ? TIOCSER_TEMT : 0; +} + +static unsigned int sbd_get_mctrl(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + unsigned int mctrl, status; + + status = read_sbdshr(sport, R_DUART_IN_PORT); + status >>= (uport->line) % 2; + mctrl = (!(status & M_DUART_IN_PIN0_VAL) ? TIOCM_CTS : 0) | + (!(status & M_DUART_IN_PIN4_VAL) ? TIOCM_CAR : 0) | + (!(status & M_DUART_RIN0_PIN) ? TIOCM_RNG : 0) | + (!(status & M_DUART_IN_PIN2_VAL) ? TIOCM_DSR : 0); + return mctrl; +} + +static void sbd_set_mctrl(struct uart_port *uport, unsigned int mctrl) +{ + struct sbd_port *sport = to_sport(uport); + unsigned int clr = 0, set = 0, mode2; + + if (mctrl & TIOCM_DTR) + set |= M_DUART_SET_OPR2; + else + clr |= M_DUART_CLR_OPR2; + if (mctrl & TIOCM_RTS) + set |= M_DUART_SET_OPR0; + else + clr |= M_DUART_CLR_OPR0; + clr <<= (uport->line) % 2; + set <<= (uport->line) % 2; + + mode2 = read_sbdchn(sport, R_DUART_MODE_REG_2); + mode2 &= ~M_DUART_CHAN_MODE; + if (mctrl & TIOCM_LOOP) + mode2 |= V_DUART_CHAN_MODE_LCL_LOOP; + else + mode2 |= V_DUART_CHAN_MODE_NORMAL; + + write_sbdshr(sport, R_DUART_CLEAR_OPR, clr); + write_sbdshr(sport, R_DUART_SET_OPR, set); + write_sbdchn(sport, R_DUART_MODE_REG_2, mode2); +} + +static void sbd_stop_tx(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + + write_sbdchn(sport, R_DUART_CMD, M_DUART_TX_DIS); + sport->tx_stopped = 1; +}; + +static void sbd_start_tx(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + unsigned int mask; + + /* Enable tx interrupts. */ + mask = read_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2)); + mask |= M_DUART_IMR_TX; + write_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2), mask); + + /* Go!, go!, go!... */ + write_sbdchn(sport, R_DUART_CMD, M_DUART_TX_EN); + sport->tx_stopped = 0; +}; + +static void sbd_stop_rx(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + + write_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2), 0); +}; + +static void sbd_enable_ms(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + + write_sbdchn(sport, R_DUART_AUXCTL_X, + M_DUART_CIN_CHNG_ENA | M_DUART_CTS_CHNG_ENA); +} + +static void sbd_break_ctl(struct uart_port *uport, int break_state) +{ + struct sbd_port *sport = to_sport(uport); + + if (break_state == -1) + write_sbdchn(sport, R_DUART_CMD, V_DUART_MISC_CMD_START_BREAK); + else + write_sbdchn(sport, R_DUART_CMD, V_DUART_MISC_CMD_STOP_BREAK); +} + + +static void sbd_receive_chars(struct sbd_port *sport) +{ + struct uart_port *uport = &sport->port; + struct uart_icount *icount; + unsigned int status, ch, flag; + int count; + + for (count = 16; count; count--) { + status = read_sbdchn(sport, R_DUART_STATUS); + if (!(status & M_DUART_RX_RDY)) + break; + + ch = read_sbdchn(sport, R_DUART_RX_HOLD); + + flag = TTY_NORMAL; + + icount = &uport->icount; + icount->rx++; + + if (unlikely(status & + (M_DUART_RCVD_BRK | M_DUART_FRM_ERR | + M_DUART_PARITY_ERR | M_DUART_OVRUN_ERR))) { + if (status & M_DUART_RCVD_BRK) { + icount->brk++; + if (uart_handle_break(uport)) + continue; + } else if (status & M_DUART_FRM_ERR) + icount->frame++; + else if (status & M_DUART_PARITY_ERR) + icount->parity++; + if (status & M_DUART_OVRUN_ERR) + icount->overrun++; + + status &= uport->read_status_mask; + if (status & M_DUART_RCVD_BRK) + flag = TTY_BREAK; + else if (status & M_DUART_FRM_ERR) + flag = TTY_FRAME; + else if (status & M_DUART_PARITY_ERR) + flag = TTY_PARITY; + } + + if (uart_handle_sysrq_char(uport, ch)) + continue; + + uart_insert_char(uport, status, M_DUART_OVRUN_ERR, ch, flag); + } + + tty_flip_buffer_push(uport->info->tty); +} + +static void sbd_transmit_chars(struct sbd_port *sport) +{ + struct uart_port *uport = &sport->port; + struct circ_buf *xmit = &sport->port.info->xmit; + unsigned int mask; + int stop_tx; + + /* XON/XOFF chars. */ + if (sport->port.x_char) { + write_sbdchn(sport, R_DUART_TX_HOLD, sport->port.x_char); + sport->port.icount.tx++; + sport->port.x_char = 0; + return; + } + + /* If nothing to do or stopped or hardware stopped. */ + stop_tx = (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)); + + /* Send char. */ + if (!stop_tx) { + write_sbdchn(sport, R_DUART_TX_HOLD, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + sport->port.icount.tx++; + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&sport->port); + } + + /* Are we are done? */ + if (stop_tx || uart_circ_empty(xmit)) { + /* Disable tx interrupts. */ + mask = read_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2)); + mask &= ~M_DUART_IMR_TX; + write_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2), mask); + } +} + +static void sbd_status_handle(struct sbd_port *sport) +{ + struct uart_port *uport = &sport->port; + unsigned int delta; + + delta = read_sbdshr(sport, R_DUART_INCHREG((uport->line) % 2)); + delta >>= (uport->line) % 2; + + if (delta & (M_DUART_IN_PIN0_VAL << S_DUART_IN_PIN_CHNG)) + uart_handle_cts_change(uport, !(delta & M_DUART_IN_PIN0_VAL)); + + if (delta & (M_DUART_IN_PIN2_VAL << S_DUART_IN_PIN_CHNG)) + uport->icount.dsr++; + + if (delta & ((M_DUART_IN_PIN2_VAL | M_DUART_IN_PIN0_VAL) << + S_DUART_IN_PIN_CHNG)) + wake_up_interruptible(&uport->info->delta_msr_wait); +} + +static irqreturn_t sbd_interrupt(int irq, void *dev_id) +{ + struct sbd_port *sport = dev_id; + struct uart_port *uport = &sport->port; + irqreturn_t status = IRQ_NONE; + unsigned int intstat; + int count; + + for (count = 16; count; count--) { + intstat = read_sbdshr(sport, + R_DUART_ISRREG((uport->line) % 2)); + intstat &= read_sbdshr(sport, + R_DUART_IMRREG((uport->line) % 2)); + intstat &= M_DUART_ISR_ALL; + if (!intstat) + break; + + if (intstat & M_DUART_ISR_RX) + sbd_receive_chars(sport); + if (intstat & M_DUART_ISR_IN) + sbd_status_handle(sport); + if (intstat & M_DUART_ISR_TX) + sbd_transmit_chars(sport); + + status = IRQ_HANDLED; + } + + return status; +} + + +static int sbd_startup(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + unsigned int mode1; + int ret; + + ret = request_irq(sport->port.irq, sbd_interrupt, + IRQF_SHARED, "sb1250-duart", sport); + if (ret) + return ret; + + /* Clear the receive FIFO. */ + sbd_receive_drain(sport); + + /* Clear the interrupt registers. */ + write_sbdchn(sport, R_DUART_CMD, V_DUART_MISC_CMD_RESET_BREAK_INT); + read_sbdshr(sport, R_DUART_INCHREG((uport->line) % 2)); + + /* Set rx/tx interrupt to FIFO available. */ + mode1 = read_sbdchn(sport, R_DUART_MODE_REG_1); + mode1 &= ~(M_DUART_RX_IRQ_SEL_RXFULL | M_DUART_TX_IRQ_SEL_TXEMPT); + write_sbdchn(sport, R_DUART_MODE_REG_1, mode1); + + /* Disable tx, enable rx. */ + write_sbdchn(sport, R_DUART_CMD, M_DUART_TX_DIS | M_DUART_RX_EN); + sport->tx_stopped = 1; + + /* Enable interrupts. */ + write_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2), + M_DUART_IMR_IN | M_DUART_IMR_RX); + + return 0; +} + +static void sbd_shutdown(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + + write_sbdchn(sport, R_DUART_CMD, M_DUART_TX_DIS | M_DUART_RX_DIS); + sport->tx_stopped = 1; + free_irq(sport->port.irq, sport); +} + + +static void sbd_init_port(struct sbd_port *sport) +{ + struct uart_port *uport = &sport->port; + + if (sport->initialised) + return; + + /* There is no DUART reset feature, so just set some sane defaults. */ + write_sbdchn(sport, R_DUART_CMD, V_DUART_MISC_CMD_RESET_TX); + write_sbdchn(sport, R_DUART_CMD, V_DUART_MISC_CMD_RESET_RX); + write_sbdchn(sport, R_DUART_MODE_REG_1, V_DUART_BITS_PER_CHAR_8); + write_sbdchn(sport, R_DUART_MODE_REG_2, 0); + write_sbdchn(sport, R_DUART_FULL_CTL, + V_DUART_INT_TIME(0) | V_DUART_SIG_FULL(15)); + write_sbdchn(sport, R_DUART_OPCR_X, 0); + write_sbdchn(sport, R_DUART_AUXCTL_X, 0); + write_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2), 0); + + sport->initialised = 1; +} + +static void sbd_set_termios(struct uart_port *uport, struct ktermios *termios, + struct ktermios *old_termios) +{ + struct sbd_port *sport = to_sport(uport); + unsigned int mode1 = 0, mode2 = 0, aux = 0; + unsigned int mode1mask = 0, mode2mask = 0, auxmask = 0; + unsigned int oldmode1, oldmode2, oldaux; + unsigned int baud, brg; + unsigned int command; + + mode1mask |= ~(M_DUART_PARITY_MODE | M_DUART_PARITY_TYPE_ODD | + M_DUART_BITS_PER_CHAR); + mode2mask |= ~M_DUART_STOP_BIT_LEN_2; + auxmask |= ~M_DUART_CTS_CHNG_ENA; + + /* Byte size. */ + switch (termios->c_cflag & CSIZE) { + case CS5: + case CS6: + /* Unsupported, leave unchanged. */ + mode1mask |= M_DUART_PARITY_MODE; + break; + case CS7: + mode1 |= V_DUART_BITS_PER_CHAR_7; + break; + case CS8: + default: + mode1 |= V_DUART_BITS_PER_CHAR_8; + break; + } + + /* Parity and stop bits. */ + if (termios->c_cflag & CSTOPB) + mode2 |= M_DUART_STOP_BIT_LEN_2; + else + mode2 |= M_DUART_STOP_BIT_LEN_1; + if (termios->c_cflag & PARENB) + mode1 |= V_DUART_PARITY_MODE_ADD; + else + mode1 |= V_DUART_PARITY_MODE_NONE; + if (termios->c_cflag & PARODD) + mode1 |= M_DUART_PARITY_TYPE_ODD; + else + mode1 |= M_DUART_PARITY_TYPE_EVEN; + + baud = uart_get_baud_rate(uport, termios, old_termios, 1200, 5000000); + brg = V_DUART_BAUD_RATE(baud); + /* The actual lower bound is 1221bps, so compensate. */ + if (brg > M_DUART_CLK_COUNTER) + brg = M_DUART_CLK_COUNTER; + + uart_update_timeout(uport, termios->c_cflag, baud); + + uport->read_status_mask = M_DUART_OVRUN_ERR; + if (termios->c_iflag & INPCK) + uport->read_status_mask |= M_DUART_FRM_ERR | + M_DUART_PARITY_ERR; + if (termios->c_iflag & (BRKINT | PARMRK)) + uport->read_status_mask |= M_DUART_RCVD_BRK; + + uport->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + uport->ignore_status_mask |= M_DUART_FRM_ERR | + M_DUART_PARITY_ERR; + if (termios->c_iflag & IGNBRK) { + uport->ignore_status_mask |= M_DUART_RCVD_BRK; + if (termios->c_iflag & IGNPAR) + uport->ignore_status_mask |= M_DUART_OVRUN_ERR; + } + + if (termios->c_cflag & CREAD) + command = M_DUART_RX_EN; + else + command = M_DUART_RX_DIS; + + if (termios->c_cflag & CRTSCTS) + aux |= M_DUART_CTS_CHNG_ENA; + else + aux &= ~M_DUART_CTS_CHNG_ENA; + + spin_lock(&uport->lock); + + if (sport->tx_stopped) + command |= M_DUART_TX_DIS; + else + command |= M_DUART_TX_EN; + + oldmode1 = read_sbdchn(sport, R_DUART_MODE_REG_1) & mode1mask; + oldmode2 = read_sbdchn(sport, R_DUART_MODE_REG_2) & mode2mask; + oldaux = read_sbdchn(sport, R_DUART_AUXCTL_X) & auxmask; + + if (!sport->tx_stopped) + sbd_line_drain(sport); + write_sbdchn(sport, R_DUART_CMD, M_DUART_TX_DIS | M_DUART_RX_DIS); + + write_sbdchn(sport, R_DUART_MODE_REG_1, mode1 | oldmode1); + write_sbdchn(sport, R_DUART_MODE_REG_2, mode2 | oldmode2); + write_sbdchn(sport, R_DUART_CLK_SEL, brg); + write_sbdchn(sport, R_DUART_AUXCTL_X, aux | oldaux); + + write_sbdchn(sport, R_DUART_CMD, command); + + spin_unlock(&uport->lock); +} + + +static const char *sbd_type(struct uart_port *uport) +{ + return "SB1250 DUART"; +} + +static void sbd_release_port(struct uart_port *uport) +{ + struct sbd_port *sport = to_sport(uport); + struct sbd_duart *duart = sport->duart; + int map_guard; + + iounmap(sport->memctrl); + sport->memctrl = NULL; + iounmap(uport->membase); + uport->membase = NULL; + + map_guard = atomic_add_return(-1, &duart->map_guard); + if (!map_guard) + release_mem_region(duart->mapctrl, DUART_CHANREG_SPACING); + release_mem_region(uport->mapbase, DUART_CHANREG_SPACING); +} + +static int sbd_map_port(struct uart_port *uport) +{ + static const char *err = KERN_ERR "sbd: Cannot map MMIO\n"; + struct sbd_port *sport = to_sport(uport); + struct sbd_duart *duart = sport->duart; + + if (!uport->membase) + uport->membase = ioremap_nocache(uport->mapbase, + DUART_CHANREG_SPACING); + if (!uport->membase) { + printk(err); + return -ENOMEM; + } + + if (!sport->memctrl) + sport->memctrl = ioremap_nocache(duart->mapctrl, + DUART_CHANREG_SPACING); + if (!sport->memctrl) { + printk(err); + iounmap(uport->membase); + uport->membase = NULL; + return -ENOMEM; + } + + return 0; +} + +static int sbd_request_port(struct uart_port *uport) +{ + static const char *err = KERN_ERR + "sbd: Unable to reserve MMIO resource\n"; + struct sbd_duart *duart = to_sport(uport)->duart; + int map_guard; + int ret = 0; + + if (!request_mem_region(uport->mapbase, DUART_CHANREG_SPACING, + "sb1250-duart")) { + printk(err); + return -EBUSY; + } + map_guard = atomic_add_return(1, &duart->map_guard); + if (map_guard == 1) { + if (!request_mem_region(duart->mapctrl, DUART_CHANREG_SPACING, + "sb1250-duart")) { + atomic_add(-1, &duart->map_guard); + printk(err); + ret = -EBUSY; + } + } + if (!ret) { + ret = sbd_map_port(uport); + if (ret) { + map_guard = atomic_add_return(-1, &duart->map_guard); + if (!map_guard) + release_mem_region(duart->mapctrl, + DUART_CHANREG_SPACING); + } + } + if (ret) { + release_mem_region(uport->mapbase, DUART_CHANREG_SPACING); + return ret; + } + return 0; +} + +static void sbd_config_port(struct uart_port *uport, int flags) +{ + struct sbd_port *sport = to_sport(uport); + + if (flags & UART_CONFIG_TYPE) { + if (sbd_request_port(uport)) + return; + + uport->type = PORT_SB1250_DUART; + + sbd_init_port(sport); + } +} + +static int sbd_verify_port(struct uart_port *uport, struct serial_struct *ser) +{ + int ret = 0; + + if (ser->type != PORT_UNKNOWN && ser->type != PORT_SB1250_DUART) + ret = -EINVAL; + if (ser->irq != uport->irq) + ret = -EINVAL; + if (ser->baud_base != uport->uartclk / 16) + ret = -EINVAL; + return ret; +} + + +static struct uart_ops sbd_ops = { + .tx_empty = sbd_tx_empty, + .set_mctrl = sbd_set_mctrl, + .get_mctrl = sbd_get_mctrl, + .stop_tx = sbd_stop_tx, + .start_tx = sbd_start_tx, + .stop_rx = sbd_stop_rx, + .enable_ms = sbd_enable_ms, + .break_ctl = sbd_break_ctl, + .startup = sbd_startup, + .shutdown = sbd_shutdown, + .set_termios = sbd_set_termios, + .type = sbd_type, + .release_port = sbd_release_port, + .request_port = sbd_request_port, + .config_port = sbd_config_port, + .verify_port = sbd_verify_port, +}; + +/* Initialize SB1250 DUART port structures. */ +static void __init sbd_probe_duarts(void) +{ + static int probed; + int chip, side; + int max_lines, line; + + if (probed) + return; + + /* Set the number of available units based on the SOC type. */ + switch (soc_type) { + case K_SYS_SOC_TYPE_BCM1x55: + case K_SYS_SOC_TYPE_BCM1x80: + max_lines = 4; + break; + default: + /* Assume at least two serial ports at the normal address. */ + max_lines = 2; + break; + } + + probed = 1; + + for (chip = 0, line = 0; chip < DUART_MAX_CHIP && line < max_lines; + chip++) { + sbd_duarts[chip].mapctrl = SBD_CTRLREGS(line); + + for (side = 0; side < DUART_MAX_SIDE && line < max_lines; + side++, line++) { + struct sbd_port *sport = &sbd_duarts[chip].sport[side]; + struct uart_port *uport = &sport->port; + + sport->duart = &sbd_duarts[chip]; + + uport->irq = SBD_INT(line); + uport->uartclk = 100000000 / 20 * 16; + uport->fifosize = 16; + uport->iotype = UPIO_MEM; + uport->flags = UPF_BOOT_AUTOCONF; + uport->ops = &sbd_ops; + uport->line = line; + uport->mapbase = SBD_CHANREGS(line); + } + } +} + + +#ifdef CONFIG_SERIAL_SB1250_DUART_CONSOLE +/* + * Serial console stuff. Very basic, polling driver for doing serial + * console output. The console_sem is held by the caller, so we + * shouldn't be interrupted for more console activity. + */ +static void sbd_console_putchar(struct uart_port *uport, int ch) +{ + struct sbd_port *sport = to_sport(uport); + + sbd_transmit_drain(sport); + write_sbdchn(sport, R_DUART_TX_HOLD, ch); +} + +static void sbd_console_write(struct console *co, const char *s, + unsigned int count) +{ + int chip = co->index / DUART_MAX_SIDE; + int side = co->index % DUART_MAX_SIDE; + struct sbd_port *sport = &sbd_duarts[chip].sport[side]; + struct uart_port *uport = &sport->port; + unsigned long flags; + unsigned int mask; + + /* Disable transmit interrupts and enable the transmitter. */ + spin_lock_irqsave(&uport->lock, flags); + mask = read_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2)); + write_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2), + mask & ~M_DUART_IMR_TX); + write_sbdchn(sport, R_DUART_CMD, M_DUART_TX_EN); + spin_unlock_irqrestore(&uport->lock, flags); + + uart_console_write(&sport->port, s, count, sbd_console_putchar); + + /* Restore transmit interrupts and the transmitter enable. */ + spin_lock_irqsave(&uport->lock, flags); + sbd_line_drain(sport); + if (sport->tx_stopped) + write_sbdchn(sport, R_DUART_CMD, M_DUART_TX_DIS); + write_sbdshr(sport, R_DUART_IMRREG((uport->line) % 2), mask); + spin_unlock_irqrestore(&uport->lock, flags); +} + +static int __init sbd_console_setup(struct console *co, char *options) +{ + int chip = co->index / DUART_MAX_SIDE; + int side = co->index % DUART_MAX_SIDE; + struct sbd_port *sport = &sbd_duarts[chip].sport[side]; + struct uart_port *uport = &sport->port; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + int ret; + + if (!sport->duart) + return -ENXIO; + + ret = sbd_map_port(uport); + if (ret) + return ret; + + sbd_init_port(sport); + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + return uart_set_options(uport, co, baud, parity, bits, flow); +} + +static struct uart_driver sbd_reg; +static struct console sbd_console = { + .name = "duart", + .write = sbd_console_write, + .device = uart_console_device, + .setup = sbd_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &sbd_reg +}; + +static int __init sbd_serial_console_init(void) +{ + sbd_probe_duarts(); + register_console(&sbd_console); + + return 0; +} + +console_initcall(sbd_serial_console_init); + +#define SERIAL_SB1250_DUART_CONSOLE &sbd_console +#else +#define SERIAL_SB1250_DUART_CONSOLE NULL +#endif /* CONFIG_SERIAL_SB1250_DUART_CONSOLE */ + + +static struct uart_driver sbd_reg = { + .owner = THIS_MODULE, + .driver_name = "serial", + .dev_name = "duart", + .major = TTY_MAJOR, + .minor = SB1250_DUART_MINOR_BASE, + .nr = DUART_MAX_CHIP * DUART_MAX_SIDE, + .cons = SERIAL_SB1250_DUART_CONSOLE, +}; + +/* Set up the driver and register it. */ +static int __init sbd_init(void) +{ + int i, ret; + + sbd_probe_duarts(); + + ret = uart_register_driver(&sbd_reg); + if (ret) + return ret; + + for (i = 0; i < DUART_MAX_CHIP * DUART_MAX_SIDE; i++) { + struct sbd_duart *duart = &sbd_duarts[i / DUART_MAX_SIDE]; + struct sbd_port *sport = &duart->sport[i % DUART_MAX_SIDE]; + struct uart_port *uport = &sport->port; + + if (sport->duart) + uart_add_one_port(&sbd_reg, uport); + } + + return 0; +} + +/* Unload the driver. Unregister stuff, get ready to go away. */ +static void __exit sbd_exit(void) +{ + int i; + + for (i = DUART_MAX_CHIP * DUART_MAX_SIDE - 1; i >= 0; i--) { + struct sbd_duart *duart = &sbd_duarts[i / DUART_MAX_SIDE]; + struct sbd_port *sport = &duart->sport[i % DUART_MAX_SIDE]; + struct uart_port *uport = &sport->port; + + if (sport->duart) + uart_remove_one_port(&sbd_reg, uport); + } + + uart_unregister_driver(&sbd_reg); +} + +module_init(sbd_init); +module_exit(sbd_exit); diff --git a/drivers/serial/sunhv.c b/drivers/serial/sunhv.c index 17bcca53d6a..d82be42ff29 100644 --- a/drivers/serial/sunhv.c +++ b/drivers/serial/sunhv.c @@ -258,17 +258,7 @@ static void sunhv_stop_tx(struct uart_port *port) /* port->lock held by caller. */ static void sunhv_start_tx(struct uart_port *port) { - struct circ_buf *xmit = &port->info->xmit; - - while (!uart_circ_empty(xmit)) { - long status = sun4v_con_putchar(xmit->buf[xmit->tail]); - - if (status != HV_EOK) - break; - - xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); - port->icount.tx++; - } + transmit_chars(port); } /* port->lock is not held. */ diff --git a/drivers/serial/zs.c b/drivers/serial/zs.c new file mode 100644 index 00000000000..65f1294fd27 --- /dev/null +++ b/drivers/serial/zs.c @@ -0,0 +1,1287 @@ +/* + * zs.c: Serial port driver for IOASIC DECstations. + * + * Derived from drivers/sbus/char/sunserial.c by Paul Mackerras. + * Derived from drivers/macintosh/macserial.c by Harald Koerfgen. + * + * DECstation changes + * Copyright (C) 1998-2000 Harald Koerfgen + * Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2007 Maciej W. Rozycki + * + * For the rest of the code the original Copyright applies: + * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au) + * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu) + * + * + * Note: for IOASIC systems the wiring is as follows: + * + * mouse/keyboard: + * DIN-7 MJ-4 signal SCC + * 2 1 TxD <- A.TxD + * 3 4 RxD -> A.RxD + * + * EIA-232/EIA-423: + * DB-25 MMJ-6 signal SCC + * 2 2 TxD <- B.TxD + * 3 5 RxD -> B.RxD + * 4 RTS <- ~A.RTS + * 5 CTS -> ~B.CTS + * 6 6 DSR -> ~A.SYNC + * 8 CD -> ~B.DCD + * 12 DSRS(DCE) -> ~A.CTS (*) + * 15 TxC -> B.TxC + * 17 RxC -> B.RxC + * 20 1 DTR <- ~A.DTR + * 22 RI -> ~A.DCD + * 23 DSRS(DTE) <- ~B.RTS + * + * (*) EIA-232 defines the signal at this pin to be SCD, while DSRS(DCE) + * is shared with DSRS(DTE) at pin 23. + * + * As you can immediately notice the wiring of the RTS, DTR and DSR signals + * is a bit odd. This makes the handling of port B unnecessarily + * complicated and prevents the use of some automatic modes of operation. + */ + +#if defined(CONFIG_SERIAL_ZS_CONSOLE) && defined(CONFIG_MAGIC_SYSRQ) +#define SUPPORT_SYSRQ +#endif + +#include <linux/bug.h> +#include <linux/console.h> +#include <linux/delay.h> +#include <linux/errno.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/ioport.h> +#include <linux/irqflags.h> +#include <linux/kernel.h> +#include <linux/major.h> +#include <linux/serial.h> +#include <linux/serial_core.h> +#include <linux/spinlock.h> +#include <linux/sysrq.h> +#include <linux/tty.h> +#include <linux/types.h> + +#include <asm/atomic.h> +#include <asm/system.h> + +#include <asm/dec/interrupts.h> +#include <asm/dec/ioasic_addrs.h> +#include <asm/dec/system.h> + +#include "zs.h" + + +MODULE_AUTHOR("Maciej W. Rozycki <macro@linux-mips.org>"); +MODULE_DESCRIPTION("DECstation Z85C30 serial driver"); +MODULE_LICENSE("GPL"); + + +static char zs_name[] __initdata = "DECstation Z85C30 serial driver version "; +static char zs_version[] __initdata = "0.10"; + +/* + * It would be nice to dynamically allocate everything that + * depends on ZS_NUM_SCCS, so we could support any number of + * Z85C30s, but for now... + */ +#define ZS_NUM_SCCS 2 /* Max # of ZS chips supported. */ +#define ZS_NUM_CHAN 2 /* 2 channels per chip. */ +#define ZS_CHAN_A 0 /* Index of the channel A. */ +#define ZS_CHAN_B 1 /* Index of the channel B. */ +#define ZS_CHAN_IO_SIZE 8 /* IOMEM space size. */ +#define ZS_CHAN_IO_STRIDE 4 /* Register alignment. */ +#define ZS_CHAN_IO_OFFSET 1 /* The SCC resides on the high byte + of the 16-bit IOBUS. */ +#define ZS_CLOCK 7372800 /* Z85C30 PCLK input clock rate. */ + +#define to_zport(uport) container_of(uport, struct zs_port, port) + +struct zs_parms { + resource_size_t scc[ZS_NUM_SCCS]; + int irq[ZS_NUM_SCCS]; +}; + +static struct zs_scc zs_sccs[ZS_NUM_SCCS]; + +static u8 zs_init_regs[ZS_NUM_REGS] __initdata = { + 0, /* write 0 */ + PAR_SPEC, /* write 1 */ + 0, /* write 2 */ + 0, /* write 3 */ + X16CLK | SB1, /* write 4 */ + 0, /* write 5 */ + 0, 0, 0, /* write 6, 7, 8 */ + MIE | DLC | NV, /* write 9 */ + NRZ, /* write 10 */ + TCBR | RCBR, /* write 11 */ + 0, 0, /* BRG time constant, write 12 + 13 */ + BRSRC | BRENABL, /* write 14 */ + 0, /* write 15 */ +}; + +/* + * Debugging. + */ +#undef ZS_DEBUG_REGS + + +/* + * Reading and writing Z85C30 registers. + */ +static void recovery_delay(void) +{ + udelay(2); +} + +static u8 read_zsreg(struct zs_port *zport, int reg) +{ + void __iomem *control = zport->port.membase + ZS_CHAN_IO_OFFSET; + u8 retval; + + if (reg != 0) { + writeb(reg & 0xf, control); + fast_iob(); + recovery_delay(); + } + retval = readb(control); + recovery_delay(); + return retval; +} + +static void write_zsreg(struct zs_port *zport, int reg, u8 value) +{ + void __iomem *control = zport->port.membase + ZS_CHAN_IO_OFFSET; + + if (reg != 0) { + writeb(reg & 0xf, control); + fast_iob(); recovery_delay(); + } + writeb(value, control); + fast_iob(); + recovery_delay(); + return; +} + +static u8 read_zsdata(struct zs_port *zport) +{ + void __iomem *data = zport->port.membase + + ZS_CHAN_IO_STRIDE + ZS_CHAN_IO_OFFSET; + u8 retval; + + retval = readb(data); + recovery_delay(); + return retval; +} + +static void write_zsdata(struct zs_port *zport, u8 value) +{ + void __iomem *data = zport->port.membase + + ZS_CHAN_IO_STRIDE + ZS_CHAN_IO_OFFSET; + + writeb(value, data); + fast_iob(); + recovery_delay(); + return; +} + +#ifdef ZS_DEBUG_REGS +void zs_dump(void) +{ + struct zs_port *zport; + int i, j; + + for (i = 0; i < ZS_NUM_SCCS * ZS_NUM_CHAN; i++) { + zport = &zs_sccs[i / ZS_NUM_CHAN].zport[i % ZS_NUM_CHAN]; + + if (!zport->scc) + continue; + + for (j = 0; j < 16; j++) + printk("W%-2d = 0x%02x\t", j, zport->regs[j]); + printk("\n"); + for (j = 0; j < 16; j++) + printk("R%-2d = 0x%02x\t", j, read_zsreg(zport, j)); + printk("\n\n"); + } +} +#endif + + +static void zs_spin_lock_cond_irq(spinlock_t *lock, int irq) +{ + if (irq) + spin_lock_irq(lock); + else + spin_lock(lock); +} + +static void zs_spin_unlock_cond_irq(spinlock_t *lock, int irq) +{ + if (irq) + spin_unlock_irq(lock); + else + spin_unlock(lock); +} + +static int zs_receive_drain(struct zs_port *zport) +{ + int loops = 10000; + + while ((read_zsreg(zport, R0) & Rx_CH_AV) && loops--) + read_zsdata(zport); + return loops; +} + +static int zs_transmit_drain(struct zs_port *zport, int irq) +{ + struct zs_scc *scc = zport->scc; + int loops = 10000; + + while (!(read_zsreg(zport, R0) & Tx_BUF_EMP) && loops--) { + zs_spin_unlock_cond_irq(&scc->zlock, irq); + udelay(2); + zs_spin_lock_cond_irq(&scc->zlock, irq); + } + return loops; +} + +static int zs_line_drain(struct zs_port *zport, int irq) +{ + struct zs_scc *scc = zport->scc; + int loops = 10000; + + while (!(read_zsreg(zport, R1) & ALL_SNT) && loops--) { + zs_spin_unlock_cond_irq(&scc->zlock, irq); + udelay(2); + zs_spin_lock_cond_irq(&scc->zlock, irq); + } + return loops; +} + + +static void load_zsregs(struct zs_port *zport, u8 *regs, int irq) +{ + /* Let the current transmission finish. */ + zs_line_drain(zport, irq); + /* Load 'em up. */ + write_zsreg(zport, R3, regs[3] & ~RxENABLE); + write_zsreg(zport, R5, regs[5] & ~TxENAB); + write_zsreg(zport, R4, regs[4]); + write_zsreg(zport, R9, regs[9]); + write_zsreg(zport, R1, regs[1]); + write_zsreg(zport, R2, regs[2]); + write_zsreg(zport, R10, regs[10]); + write_zsreg(zport, R14, regs[14] & ~BRENABL); + write_zsreg(zport, R11, regs[11]); + write_zsreg(zport, R12, regs[12]); + write_zsreg(zport, R13, regs[13]); + write_zsreg(zport, R14, regs[14]); + write_zsreg(zport, R15, regs[15]); + if (regs[3] & RxENABLE) + write_zsreg(zport, R3, regs[3]); + if (regs[5] & TxENAB) + write_zsreg(zport, R5, regs[5]); + return; +} + + +/* + * Status handling routines. + */ + +/* + * zs_tx_empty() -- get the transmitter empty status + * + * Purpose: Let user call ioctl() to get info when the UART physically + * is emptied. On bus types like RS485, the transmitter must + * release the bus after transmitting. This must be done when + * the transmit shift register is empty, not be done when the + * transmit holding register is empty. This functionality + * allows an RS485 driver to be written in user space. + */ +static unsigned int zs_tx_empty(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + unsigned long flags; + u8 status; + + spin_lock_irqsave(&scc->zlock, flags); + status = read_zsreg(zport, R1); + spin_unlock_irqrestore(&scc->zlock, flags); + + return status & ALL_SNT ? TIOCSER_TEMT : 0; +} + +static unsigned int zs_raw_get_ab_mctrl(struct zs_port *zport_a, + struct zs_port *zport_b) +{ + u8 status_a, status_b; + unsigned int mctrl; + + status_a = read_zsreg(zport_a, R0); + status_b = read_zsreg(zport_b, R0); + + mctrl = ((status_b & CTS) ? TIOCM_CTS : 0) | + ((status_b & DCD) ? TIOCM_CAR : 0) | + ((status_a & DCD) ? TIOCM_RNG : 0) | + ((status_a & SYNC_HUNT) ? TIOCM_DSR : 0); + + return mctrl; +} + +static unsigned int zs_raw_get_mctrl(struct zs_port *zport) +{ + struct zs_port *zport_a = &zport->scc->zport[ZS_CHAN_A]; + + return zport != zport_a ? zs_raw_get_ab_mctrl(zport_a, zport) : 0; +} + +static unsigned int zs_raw_xor_mctrl(struct zs_port *zport) +{ + struct zs_port *zport_a = &zport->scc->zport[ZS_CHAN_A]; + unsigned int mmask, mctrl, delta; + u8 mask_a, mask_b; + + if (zport == zport_a) + return 0; + + mask_a = zport_a->regs[15]; + mask_b = zport->regs[15]; + + mmask = ((mask_b & CTSIE) ? TIOCM_CTS : 0) | + ((mask_b & DCDIE) ? TIOCM_CAR : 0) | + ((mask_a & DCDIE) ? TIOCM_RNG : 0) | + ((mask_a & SYNCIE) ? TIOCM_DSR : 0); + + mctrl = zport->mctrl; + if (mmask) { + mctrl &= ~mmask; + mctrl |= zs_raw_get_ab_mctrl(zport_a, zport) & mmask; + } + + delta = mctrl ^ zport->mctrl; + if (delta) + zport->mctrl = mctrl; + + return delta; +} + +static unsigned int zs_get_mctrl(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + unsigned int mctrl; + + spin_lock(&scc->zlock); + mctrl = zs_raw_get_mctrl(zport); + spin_unlock(&scc->zlock); + + return mctrl; +} + +static void zs_set_mctrl(struct uart_port *uport, unsigned int mctrl) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + struct zs_port *zport_a = &scc->zport[ZS_CHAN_A]; + u8 oldloop, newloop; + + spin_lock(&scc->zlock); + if (zport != zport_a) { + if (mctrl & TIOCM_DTR) + zport_a->regs[5] |= DTR; + else + zport_a->regs[5] &= ~DTR; + if (mctrl & TIOCM_RTS) + zport_a->regs[5] |= RTS; + else + zport_a->regs[5] &= ~RTS; + write_zsreg(zport_a, R5, zport_a->regs[5]); + } + + /* Rarely modified, so don't poke at hardware unless necessary. */ + oldloop = zport->regs[14]; + newloop = oldloop; + if (mctrl & TIOCM_LOOP) + newloop |= LOOPBAK; + else + newloop &= ~LOOPBAK; + if (newloop != oldloop) { + zport->regs[14] = newloop; + write_zsreg(zport, R14, zport->regs[14]); + } + spin_unlock(&scc->zlock); +} + +static void zs_raw_stop_tx(struct zs_port *zport) +{ + write_zsreg(zport, R0, RES_Tx_P); + zport->tx_stopped = 1; +} + +static void zs_stop_tx(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + + spin_lock(&scc->zlock); + zs_raw_stop_tx(zport); + spin_unlock(&scc->zlock); +} + +static void zs_raw_transmit_chars(struct zs_port *); + +static void zs_start_tx(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + + spin_lock(&scc->zlock); + if (zport->tx_stopped) { + zs_transmit_drain(zport, 0); + zport->tx_stopped = 0; + zs_raw_transmit_chars(zport); + } + spin_unlock(&scc->zlock); +} + +static void zs_stop_rx(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + struct zs_port *zport_a = &scc->zport[ZS_CHAN_A]; + + spin_lock(&scc->zlock); + zport->regs[15] &= ~BRKIE; + zport->regs[1] &= ~(RxINT_MASK | TxINT_ENAB); + zport->regs[1] |= RxINT_DISAB; + + if (zport != zport_a) { + /* A-side DCD tracks RI and SYNC tracks DSR. */ + zport_a->regs[15] &= ~(DCDIE | SYNCIE); + write_zsreg(zport_a, R15, zport_a->regs[15]); + if (!(zport_a->regs[15] & BRKIE)) { + zport_a->regs[1] &= ~EXT_INT_ENAB; + write_zsreg(zport_a, R1, zport_a->regs[1]); + } + + /* This-side DCD tracks DCD and CTS tracks CTS. */ + zport->regs[15] &= ~(DCDIE | CTSIE); + zport->regs[1] &= ~EXT_INT_ENAB; + } else { + /* DCD tracks RI and SYNC tracks DSR for the B side. */ + if (!(zport->regs[15] & (DCDIE | SYNCIE))) + zport->regs[1] &= ~EXT_INT_ENAB; + } + + write_zsreg(zport, R15, zport->regs[15]); + write_zsreg(zport, R1, zport->regs[1]); + spin_unlock(&scc->zlock); +} + +static void zs_enable_ms(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + struct zs_port *zport_a = &scc->zport[ZS_CHAN_A]; + + if (zport == zport_a) + return; + + spin_lock(&scc->zlock); + + /* Clear Ext interrupts if not being handled already. */ + if (!(zport_a->regs[1] & EXT_INT_ENAB)) + write_zsreg(zport_a, R0, RES_EXT_INT); + + /* A-side DCD tracks RI and SYNC tracks DSR. */ + zport_a->regs[1] |= EXT_INT_ENAB; + zport_a->regs[15] |= DCDIE | SYNCIE; + + /* This-side DCD tracks DCD and CTS tracks CTS. */ + zport->regs[15] |= DCDIE | CTSIE; + + zs_raw_xor_mctrl(zport); + + write_zsreg(zport_a, R1, zport_a->regs[1]); + write_zsreg(zport_a, R15, zport_a->regs[15]); + write_zsreg(zport, R15, zport->regs[15]); + spin_unlock(&scc->zlock); +} + +static void zs_break_ctl(struct uart_port *uport, int break_state) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + unsigned long flags; + + spin_lock_irqsave(&scc->zlock, flags); + if (break_state == -1) + zport->regs[5] |= SND_BRK; + else + zport->regs[5] &= ~SND_BRK; + write_zsreg(zport, R5, zport->regs[5]); + spin_unlock_irqrestore(&scc->zlock, flags); +} + + +/* + * Interrupt handling routines. + */ +#define Rx_BRK 0x0100 /* BREAK event software flag. */ +#define Rx_SYS 0x0200 /* SysRq event software flag. */ + +static void zs_receive_chars(struct zs_port *zport) +{ + struct uart_port *uport = &zport->port; + struct zs_scc *scc = zport->scc; + struct uart_icount *icount; + unsigned int avail, status, ch, flag; + int count; + + for (count = 16; count; count--) { + spin_lock(&scc->zlock); + avail = read_zsreg(zport, R0) & Rx_CH_AV; + spin_unlock(&scc->zlock); + if (!avail) + break; + + spin_lock(&scc->zlock); + status = read_zsreg(zport, R1) & (Rx_OVR | FRM_ERR | PAR_ERR); + ch = read_zsdata(zport); + spin_unlock(&scc->zlock); + + flag = TTY_NORMAL; + + icount = &uport->icount; + icount->rx++; + + /* Handle the null char got when BREAK is removed. */ + if (!ch) + status |= zport->tty_break; + if (unlikely(status & + (Rx_OVR | FRM_ERR | PAR_ERR | Rx_SYS | Rx_BRK))) { + zport->tty_break = 0; + + /* Reset the error indication. */ + if (status & (Rx_OVR | FRM_ERR | PAR_ERR)) { + spin_lock(&scc->zlock); + write_zsreg(zport, R0, ERR_RES); + spin_unlock(&scc->zlock); + } + + if (status & (Rx_SYS | Rx_BRK)) { + icount->brk++; + /* SysRq discards the null char. */ + if (status & Rx_SYS) + continue; + } else if (status & FRM_ERR) + icount->frame++; + else if (status & PAR_ERR) + icount->parity++; + if (status & Rx_OVR) + icount->overrun++; + + status &= uport->read_status_mask; + if (status & Rx_BRK) + flag = TTY_BREAK; + else if (status & FRM_ERR) + flag = TTY_FRAME; + else if (status & PAR_ERR) + flag = TTY_PARITY; + } + + if (uart_handle_sysrq_char(uport, ch)) + continue; + + uart_insert_char(uport, status, Rx_OVR, ch, flag); + } + + tty_flip_buffer_push(uport->info->tty); +} + +static void zs_raw_transmit_chars(struct zs_port *zport) +{ + struct circ_buf *xmit = &zport->port.info->xmit; + + /* XON/XOFF chars. */ + if (zport->port.x_char) { + write_zsdata(zport, zport->port.x_char); + zport->port.icount.tx++; + zport->port.x_char = 0; + return; + } + + /* If nothing to do or stopped or hardware stopped. */ + if (uart_circ_empty(xmit) || uart_tx_stopped(&zport->port)) { + zs_raw_stop_tx(zport); + return; + } + + /* Send char. */ + write_zsdata(zport, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + zport->port.icount.tx++; + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&zport->port); + + /* Are we are done? */ + if (uart_circ_empty(xmit)) + zs_raw_stop_tx(zport); +} + +static void zs_transmit_chars(struct zs_port *zport) +{ + struct zs_scc *scc = zport->scc; + + spin_lock(&scc->zlock); + zs_raw_transmit_chars(zport); + spin_unlock(&scc->zlock); +} + +static void zs_status_handle(struct zs_port *zport, struct zs_port *zport_a) +{ + struct uart_port *uport = &zport->port; + struct zs_scc *scc = zport->scc; + unsigned int delta; + u8 status, brk; + + spin_lock(&scc->zlock); + + /* Get status from Read Register 0. */ + status = read_zsreg(zport, R0); + + if (zport->regs[15] & BRKIE) { + brk = status & BRK_ABRT; + if (brk && !zport->brk) { + spin_unlock(&scc->zlock); + if (uart_handle_break(uport)) + zport->tty_break = Rx_SYS; + else + zport->tty_break = Rx_BRK; + spin_lock(&scc->zlock); + } + zport->brk = brk; + } + + if (zport != zport_a) { + delta = zs_raw_xor_mctrl(zport); + spin_unlock(&scc->zlock); + + if (delta & TIOCM_CTS) + uart_handle_cts_change(uport, + zport->mctrl & TIOCM_CTS); + if (delta & TIOCM_CAR) + uart_handle_dcd_change(uport, + zport->mctrl & TIOCM_CAR); + if (delta & TIOCM_RNG) + uport->icount.dsr++; + if (delta & TIOCM_DSR) + uport->icount.rng++; + + if (delta) + wake_up_interruptible(&uport->info->delta_msr_wait); + + spin_lock(&scc->zlock); + } + + /* Clear the status condition... */ + write_zsreg(zport, R0, RES_EXT_INT); + + spin_unlock(&scc->zlock); +} + +/* + * This is the Z85C30 driver's generic interrupt routine. + */ +static irqreturn_t zs_interrupt(int irq, void *dev_id) +{ + struct zs_scc *scc = dev_id; + struct zs_port *zport_a = &scc->zport[ZS_CHAN_A]; + struct zs_port *zport_b = &scc->zport[ZS_CHAN_B]; + irqreturn_t status = IRQ_NONE; + u8 zs_intreg; + int count; + + /* + * NOTE: The read register 3, which holds the irq status, + * does so for both channels on each chip. Although + * the status value itself must be read from the A + * channel and is only valid when read from channel A. + * Yes... broken hardware... + */ + for (count = 16; count; count--) { + spin_lock(&scc->zlock); + zs_intreg = read_zsreg(zport_a, R3); + spin_unlock(&scc->zlock); + if (!zs_intreg) + break; + + /* + * We do not like losing characters, so we prioritise + * interrupt sources a little bit differently than + * the SCC would, was it allowed to. + */ + if (zs_intreg & CHBRxIP) + zs_receive_chars(zport_b); + if (zs_intreg & CHARxIP) + zs_receive_chars(zport_a); + if (zs_intreg & CHBEXT) + zs_status_handle(zport_b, zport_a); + if (zs_intreg & CHAEXT) + zs_status_handle(zport_a, zport_a); + if (zs_intreg & CHBTxIP) + zs_transmit_chars(zport_b); + if (zs_intreg & CHATxIP) + zs_transmit_chars(zport_a); + + status = IRQ_HANDLED; + } + + return status; +} + + +/* + * Finally, routines used to initialize the serial port. + */ +static int zs_startup(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + unsigned long flags; + int irq_guard; + int ret; + + irq_guard = atomic_add_return(1, &scc->irq_guard); + if (irq_guard == 1) { + ret = request_irq(zport->port.irq, zs_interrupt, + IRQF_SHARED, "scc", scc); + if (ret) { + atomic_add(-1, &scc->irq_guard); + printk(KERN_ERR "zs: can't get irq %d\n", + zport->port.irq); + return ret; + } + } + + spin_lock_irqsave(&scc->zlock, flags); + + /* Clear the receive FIFO. */ + zs_receive_drain(zport); + + /* Clear the interrupt registers. */ + write_zsreg(zport, R0, ERR_RES); + write_zsreg(zport, R0, RES_Tx_P); + /* But Ext only if not being handled already. */ + if (!(zport->regs[1] & EXT_INT_ENAB)) + write_zsreg(zport, R0, RES_EXT_INT); + + /* Finally, enable sequencing and interrupts. */ + zport->regs[1] &= ~RxINT_MASK; + zport->regs[1] |= RxINT_ALL | TxINT_ENAB | EXT_INT_ENAB; + zport->regs[3] |= RxENABLE; + zport->regs[5] |= TxENAB; + zport->regs[15] |= BRKIE; + write_zsreg(zport, R1, zport->regs[1]); + write_zsreg(zport, R3, zport->regs[3]); + write_zsreg(zport, R5, zport->regs[5]); + write_zsreg(zport, R15, zport->regs[15]); + + /* Record the current state of RR0. */ + zport->mctrl = zs_raw_get_mctrl(zport); + zport->brk = read_zsreg(zport, R0) & BRK_ABRT; + + zport->tx_stopped = 1; + + spin_unlock_irqrestore(&scc->zlock, flags); + + return 0; +} + +static void zs_shutdown(struct uart_port *uport) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + unsigned long flags; + int irq_guard; + + spin_lock_irqsave(&scc->zlock, flags); + + zport->regs[5] &= ~TxENAB; + zport->regs[3] &= ~RxENABLE; + write_zsreg(zport, R5, zport->regs[5]); + write_zsreg(zport, R3, zport->regs[3]); + + spin_unlock_irqrestore(&scc->zlock, flags); + + irq_guard = atomic_add_return(-1, &scc->irq_guard); + if (!irq_guard) + free_irq(zport->port.irq, scc); +} + + +static void zs_reset(struct zs_port *zport) +{ + struct zs_scc *scc = zport->scc; + int irq; + unsigned long flags; + + spin_lock_irqsave(&scc->zlock, flags); + irq = !irqs_disabled_flags(flags); + if (!scc->initialised) { + /* Reset the pointer first, just in case... */ + read_zsreg(zport, R0); + /* And let the current transmission finish. */ + zs_line_drain(zport, irq); + write_zsreg(zport, R9, FHWRES); + udelay(10); + write_zsreg(zport, R9, 0); + scc->initialised = 1; + } + load_zsregs(zport, zport->regs, irq); + spin_unlock_irqrestore(&scc->zlock, flags); +} + +static void zs_set_termios(struct uart_port *uport, struct ktermios *termios, + struct ktermios *old_termios) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + struct zs_port *zport_a = &scc->zport[ZS_CHAN_A]; + int irq; + unsigned int baud, brg; + unsigned long flags; + + spin_lock_irqsave(&scc->zlock, flags); + irq = !irqs_disabled_flags(flags); + + /* Byte size. */ + zport->regs[3] &= ~RxNBITS_MASK; + zport->regs[5] &= ~TxNBITS_MASK; + switch (termios->c_cflag & CSIZE) { + case CS5: + zport->regs[3] |= Rx5; + zport->regs[5] |= Tx5; + break; + case CS6: + zport->regs[3] |= Rx6; + zport->regs[5] |= Tx6; + break; + case CS7: + zport->regs[3] |= Rx7; + zport->regs[5] |= Tx7; + break; + case CS8: + default: + zport->regs[3] |= Rx8; + zport->regs[5] |= Tx8; + break; + } + + /* Parity and stop bits. */ + zport->regs[4] &= ~(XCLK_MASK | SB_MASK | PAR_ENA | PAR_EVEN); + if (termios->c_cflag & CSTOPB) + zport->regs[4] |= SB2; + else + zport->regs[4] |= SB1; + if (termios->c_cflag & PARENB) + zport->regs[4] |= PAR_ENA; + if (!(termios->c_cflag & PARODD)) + zport->regs[4] |= PAR_EVEN; + switch (zport->clk_mode) { + case 64: + zport->regs[4] |= X64CLK; + break; + case 32: + zport->regs[4] |= X32CLK; + break; + case 16: + zport->regs[4] |= X16CLK; + break; + case 1: + zport->regs[4] |= X1CLK; + break; + default: + BUG(); + } + + baud = uart_get_baud_rate(uport, termios, old_termios, 0, + uport->uartclk / zport->clk_mode / 4); + + brg = ZS_BPS_TO_BRG(baud, uport->uartclk / zport->clk_mode); + zport->regs[12] = brg & 0xff; + zport->regs[13] = (brg >> 8) & 0xff; + + uart_update_timeout(uport, termios->c_cflag, baud); + + uport->read_status_mask = Rx_OVR; + if (termios->c_iflag & INPCK) + uport->read_status_mask |= FRM_ERR | PAR_ERR; + if (termios->c_iflag & (BRKINT | PARMRK)) + uport->read_status_mask |= Rx_BRK; + + uport->ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + uport->ignore_status_mask |= FRM_ERR | PAR_ERR; + if (termios->c_iflag & IGNBRK) { + uport->ignore_status_mask |= Rx_BRK; + if (termios->c_iflag & IGNPAR) + uport->ignore_status_mask |= Rx_OVR; + } + + if (termios->c_cflag & CREAD) + zport->regs[3] |= RxENABLE; + else + zport->regs[3] &= ~RxENABLE; + + if (zport != zport_a) { + if (!(termios->c_cflag & CLOCAL)) { + zport->regs[15] |= DCDIE; + } else + zport->regs[15] &= ~DCDIE; + if (termios->c_cflag & CRTSCTS) { + zport->regs[15] |= CTSIE; + } else + zport->regs[15] &= ~CTSIE; + zs_raw_xor_mctrl(zport); + } + + /* Load up the new values. */ + load_zsregs(zport, zport->regs, irq); + + spin_unlock_irqrestore(&scc->zlock, flags); +} + + +static const char *zs_type(struct uart_port *uport) +{ + return "Z85C30 SCC"; +} + +static void zs_release_port(struct uart_port *uport) +{ + iounmap(uport->membase); + uport->membase = 0; + release_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE); +} + +static int zs_map_port(struct uart_port *uport) +{ + if (!uport->membase) + uport->membase = ioremap_nocache(uport->mapbase, + ZS_CHAN_IO_SIZE); + if (!uport->membase) { + printk(KERN_ERR "zs: Cannot map MMIO\n"); + return -ENOMEM; + } + return 0; +} + +static int zs_request_port(struct uart_port *uport) +{ + int ret; + + if (!request_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE, "scc")) { + printk(KERN_ERR "zs: Unable to reserve MMIO resource\n"); + return -EBUSY; + } + ret = zs_map_port(uport); + if (ret) { + release_mem_region(uport->mapbase, ZS_CHAN_IO_SIZE); + return ret; + } + return 0; +} + +static void zs_config_port(struct uart_port *uport, int flags) +{ + struct zs_port *zport = to_zport(uport); + + if (flags & UART_CONFIG_TYPE) { + if (zs_request_port(uport)) + return; + + uport->type = PORT_ZS; + + zs_reset(zport); + } +} + +static int zs_verify_port(struct uart_port *uport, struct serial_struct *ser) +{ + struct zs_port *zport = to_zport(uport); + int ret = 0; + + if (ser->type != PORT_UNKNOWN && ser->type != PORT_ZS) + ret = -EINVAL; + if (ser->irq != uport->irq) + ret = -EINVAL; + if (ser->baud_base != uport->uartclk / zport->clk_mode / 4) + ret = -EINVAL; + return ret; +} + + +static struct uart_ops zs_ops = { + .tx_empty = zs_tx_empty, + .set_mctrl = zs_set_mctrl, + .get_mctrl = zs_get_mctrl, + .stop_tx = zs_stop_tx, + .start_tx = zs_start_tx, + .stop_rx = zs_stop_rx, + .enable_ms = zs_enable_ms, + .break_ctl = zs_break_ctl, + .startup = zs_startup, + .shutdown = zs_shutdown, + .set_termios = zs_set_termios, + .type = zs_type, + .release_port = zs_release_port, + .request_port = zs_request_port, + .config_port = zs_config_port, + .verify_port = zs_verify_port, +}; + +/* + * Initialize Z85C30 port structures. + */ +static int __init zs_probe_sccs(void) +{ + static int probed; + struct zs_parms zs_parms; + int chip, side, irq; + int n_chips = 0; + int i; + + if (probed) + return 0; + + irq = dec_interrupt[DEC_IRQ_SCC0]; + if (irq >= 0) { + zs_parms.scc[n_chips] = IOASIC_SCC0; + zs_parms.irq[n_chips] = dec_interrupt[DEC_IRQ_SCC0]; + n_chips++; + } + irq = dec_interrupt[DEC_IRQ_SCC1]; + if (irq >= 0) { + zs_parms.scc[n_chips] = IOASIC_SCC1; + zs_parms.irq[n_chips] = dec_interrupt[DEC_IRQ_SCC1]; + n_chips++; + } + if (!n_chips) + return -ENXIO; + + probed = 1; + + for (chip = 0; chip < n_chips; chip++) { + spin_lock_init(&zs_sccs[chip].zlock); + for (side = 0; side < ZS_NUM_CHAN; side++) { + struct zs_port *zport = &zs_sccs[chip].zport[side]; + struct uart_port *uport = &zport->port; + + zport->scc = &zs_sccs[chip]; + zport->clk_mode = 16; + + uport->irq = zs_parms.irq[chip]; + uport->uartclk = ZS_CLOCK; + uport->fifosize = 1; + uport->iotype = UPIO_MEM; + uport->flags = UPF_BOOT_AUTOCONF; + uport->ops = &zs_ops; + uport->line = chip * ZS_NUM_CHAN + side; + uport->mapbase = dec_kn_slot_base + + zs_parms.scc[chip] + + (side ^ ZS_CHAN_B) * ZS_CHAN_IO_SIZE; + + for (i = 0; i < ZS_NUM_REGS; i++) + zport->regs[i] = zs_init_regs[i]; + } + } + + return 0; +} + + +#ifdef CONFIG_SERIAL_ZS_CONSOLE +static void zs_console_putchar(struct uart_port *uport, int ch) +{ + struct zs_port *zport = to_zport(uport); + struct zs_scc *scc = zport->scc; + int irq; + unsigned long flags; + + spin_lock_irqsave(&scc->zlock, flags); + irq = !irqs_disabled_flags(flags); + if (zs_transmit_drain(zport, irq)) + write_zsdata(zport, ch); + spin_unlock_irqrestore(&scc->zlock, flags); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + */ +static void zs_console_write(struct console *co, const char *s, + unsigned int count) +{ + int chip = co->index / ZS_NUM_CHAN, side = co->index % ZS_NUM_CHAN; + struct zs_port *zport = &zs_sccs[chip].zport[side]; + struct zs_scc *scc = zport->scc; + unsigned long flags; + u8 txint, txenb; + int irq; + + /* Disable transmit interrupts and enable the transmitter. */ + spin_lock_irqsave(&scc->zlock, flags); + txint = zport->regs[1]; + txenb = zport->regs[5]; + if (txint & TxINT_ENAB) { + zport->regs[1] = txint & ~TxINT_ENAB; + write_zsreg(zport, R1, zport->regs[1]); + } + if (!(txenb & TxENAB)) { + zport->regs[5] = txenb | TxENAB; + write_zsreg(zport, R5, zport->regs[5]); + } + spin_unlock_irqrestore(&scc->zlock, flags); + + uart_console_write(&zport->port, s, count, zs_console_putchar); + + /* Restore transmit interrupts and the transmitter enable. */ + spin_lock_irqsave(&scc->zlock, flags); + irq = !irqs_disabled_flags(flags); + zs_line_drain(zport, irq); + if (!(txenb & TxENAB)) { + zport->regs[5] &= ~TxENAB; + write_zsreg(zport, R5, zport->regs[5]); + } + if (txint & TxINT_ENAB) { + zport->regs[1] |= TxINT_ENAB; + write_zsreg(zport, R1, zport->regs[1]); + } + spin_unlock_irqrestore(&scc->zlock, flags); +} + +/* + * Setup serial console baud/bits/parity. We do two things here: + * - construct a cflag setting for the first uart_open() + * - initialise the serial port + * Return non-zero if we didn't find a serial port. + */ +static int __init zs_console_setup(struct console *co, char *options) +{ + int chip = co->index / ZS_NUM_CHAN, side = co->index % ZS_NUM_CHAN; + struct zs_port *zport = &zs_sccs[chip].zport[side]; + struct uart_port *uport = &zport->port; + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + int ret; + + ret = zs_map_port(uport); + if (ret) + return ret; + + zs_reset(zport); + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + return uart_set_options(uport, co, baud, parity, bits, flow); +} + +static struct uart_driver zs_reg; +static struct console zs_console = { + .name = "ttyS", + .write = zs_console_write, + .device = uart_console_device, + .setup = zs_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &zs_reg, +}; + +/* + * Register console. + */ +static int __init zs_serial_console_init(void) +{ + int ret; + + ret = zs_probe_sccs(); + if (ret) + return ret; + register_console(&zs_console); + + return 0; +} + +console_initcall(zs_serial_console_init); + +#define SERIAL_ZS_CONSOLE &zs_console +#else +#define SERIAL_ZS_CONSOLE NULL +#endif /* CONFIG_SERIAL_ZS_CONSOLE */ + +static struct uart_driver zs_reg = { + .owner = THIS_MODULE, + .driver_name = "serial", + .dev_name = "ttyS", + .major = TTY_MAJOR, + .minor = 64, + .nr = ZS_NUM_SCCS * ZS_NUM_CHAN, + .cons = SERIAL_ZS_CONSOLE, +}; + +/* zs_init inits the driver. */ +static int __init zs_init(void) +{ + int i, ret; + + pr_info("%s%s\n", zs_name, zs_version); + + /* Find out how many Z85C30 SCCs we have. */ + ret = zs_probe_sccs(); + if (ret) + return ret; + + ret = uart_register_driver(&zs_reg); + if (ret) + return ret; + + for (i = 0; i < ZS_NUM_SCCS * ZS_NUM_CHAN; i++) { + struct zs_scc *scc = &zs_sccs[i / ZS_NUM_CHAN]; + struct zs_port *zport = &scc->zport[i % ZS_NUM_CHAN]; + struct uart_port *uport = &zport->port; + + if (zport->scc) + uart_add_one_port(&zs_reg, uport); + } + + return 0; +} + +static void __exit zs_exit(void) +{ + int i; + + for (i = ZS_NUM_SCCS * ZS_NUM_CHAN - 1; i >= 0; i--) { + struct zs_scc *scc = &zs_sccs[i / ZS_NUM_CHAN]; + struct zs_port *zport = &scc->zport[i % ZS_NUM_CHAN]; + struct uart_port *uport = &zport->port; + + if (zport->scc) + uart_remove_one_port(&zs_reg, uport); + } + + uart_unregister_driver(&zs_reg); +} + +module_init(zs_init); +module_exit(zs_exit); diff --git a/drivers/serial/zs.h b/drivers/serial/zs.h new file mode 100644 index 00000000000..aa921b57d82 --- /dev/null +++ b/drivers/serial/zs.h @@ -0,0 +1,284 @@ +/* + * zs.h: Definitions for the DECstation Z85C30 serial driver. + * + * Adapted from drivers/sbus/char/sunserial.h by Paul Mackerras. + * Adapted from drivers/macintosh/macserial.h by Harald Koerfgen. + * + * Copyright (C) 1996 Paul Mackerras (Paul.Mackerras@cs.anu.edu.au) + * Copyright (C) 1995 David S. Miller (davem@caip.rutgers.edu) + * Copyright (C) 2004, 2005, 2007 Maciej W. Rozycki + */ +#ifndef _SERIAL_ZS_H +#define _SERIAL_ZS_H + +#ifdef __KERNEL__ + +#define ZS_NUM_REGS 16 + +/* + * This is our internal structure for each serial port's state. + */ +struct zs_port { + struct zs_scc *scc; /* Containing SCC. */ + struct uart_port port; /* Underlying UART. */ + + int clk_mode; /* May be 1, 16, 32, or 64. */ + + unsigned int tty_break; /* Set on BREAK condition. */ + int tx_stopped; /* Output is suspended. */ + + unsigned int mctrl; /* State of modem lines. */ + u8 brk; /* BREAK state from RR0. */ + + u8 regs[ZS_NUM_REGS]; /* Channel write registers. */ +}; + +/* + * Per-SCC state for locking and the interrupt handler. + */ +struct zs_scc { + struct zs_port zport[2]; + spinlock_t zlock; + atomic_t irq_guard; + int initialised; +}; + +#endif /* __KERNEL__ */ + +/* + * Conversion routines to/from brg time constants from/to bits per second. + */ +#define ZS_BRG_TO_BPS(brg, freq) ((freq) / 2 / ((brg) + 2)) +#define ZS_BPS_TO_BRG(bps, freq) ((((freq) + (bps)) / (2 * (bps))) - 2) + +/* + * The Zilog register set. + */ + +/* Write Register 0 (Command) */ +#define R0 0 /* Register selects */ +#define R1 1 +#define R2 2 +#define R3 3 +#define R4 4 +#define R5 5 +#define R6 6 +#define R7 7 +#define R8 8 +#define R9 9 +#define R10 10 +#define R11 11 +#define R12 12 +#define R13 13 +#define R14 14 +#define R15 15 + +#define NULLCODE 0 /* Null Code */ +#define POINT_HIGH 0x8 /* Select upper half of registers */ +#define RES_EXT_INT 0x10 /* Reset Ext. Status Interrupts */ +#define SEND_ABORT 0x18 /* HDLC Abort */ +#define RES_RxINT_FC 0x20 /* Reset RxINT on First Character */ +#define RES_Tx_P 0x28 /* Reset TxINT Pending */ +#define ERR_RES 0x30 /* Error Reset */ +#define RES_H_IUS 0x38 /* Reset highest IUS */ + +#define RES_Rx_CRC 0x40 /* Reset Rx CRC Checker */ +#define RES_Tx_CRC 0x80 /* Reset Tx CRC Checker */ +#define RES_EOM_L 0xC0 /* Reset EOM latch */ + +/* Write Register 1 (Tx/Rx/Ext Int Enable and WAIT/DMA Commands) */ +#define EXT_INT_ENAB 0x1 /* Ext Int Enable */ +#define TxINT_ENAB 0x2 /* Tx Int Enable */ +#define PAR_SPEC 0x4 /* Parity is special condition */ + +#define RxINT_DISAB 0 /* Rx Int Disable */ +#define RxINT_FCERR 0x8 /* Rx Int on First Character Only or Error */ +#define RxINT_ALL 0x10 /* Int on all Rx Characters or error */ +#define RxINT_ERR 0x18 /* Int on error only */ +#define RxINT_MASK 0x18 + +#define WT_RDY_RT 0x20 /* Wait/Ready on R/T */ +#define WT_FN_RDYFN 0x40 /* Wait/FN/Ready FN */ +#define WT_RDY_ENAB 0x80 /* Wait/Ready Enable */ + +/* Write Register 2 (Interrupt Vector) */ + +/* Write Register 3 (Receive Parameters and Control) */ +#define RxENABLE 0x1 /* Rx Enable */ +#define SYNC_L_INH 0x2 /* Sync Character Load Inhibit */ +#define ADD_SM 0x4 /* Address Search Mode (SDLC) */ +#define RxCRC_ENAB 0x8 /* Rx CRC Enable */ +#define ENT_HM 0x10 /* Enter Hunt Mode */ +#define AUTO_ENAB 0x20 /* Auto Enables */ +#define Rx5 0x0 /* Rx 5 Bits/Character */ +#define Rx7 0x40 /* Rx 7 Bits/Character */ +#define Rx6 0x80 /* Rx 6 Bits/Character */ +#define Rx8 0xc0 /* Rx 8 Bits/Character */ +#define RxNBITS_MASK 0xc0 + +/* Write Register 4 (Transmit/Receive Miscellaneous Parameters and Modes) */ +#define PAR_ENA 0x1 /* Parity Enable */ +#define PAR_EVEN 0x2 /* Parity Even/Odd* */ + +#define SYNC_ENAB 0 /* Sync Modes Enable */ +#define SB1 0x4 /* 1 stop bit/char */ +#define SB15 0x8 /* 1.5 stop bits/char */ +#define SB2 0xc /* 2 stop bits/char */ +#define SB_MASK 0xc + +#define MONSYNC 0 /* 8 Bit Sync character */ +#define BISYNC 0x10 /* 16 bit sync character */ +#define SDLC 0x20 /* SDLC Mode (01111110 Sync Flag) */ +#define EXTSYNC 0x30 /* External Sync Mode */ + +#define X1CLK 0x0 /* x1 clock mode */ +#define X16CLK 0x40 /* x16 clock mode */ +#define X32CLK 0x80 /* x32 clock mode */ +#define X64CLK 0xc0 /* x64 clock mode */ +#define XCLK_MASK 0xc0 + +/* Write Register 5 (Transmit Parameters and Controls) */ +#define TxCRC_ENAB 0x1 /* Tx CRC Enable */ +#define RTS 0x2 /* RTS */ +#define SDLC_CRC 0x4 /* SDLC/CRC-16 */ +#define TxENAB 0x8 /* Tx Enable */ +#define SND_BRK 0x10 /* Send Break */ +#define Tx5 0x0 /* Tx 5 bits (or less)/character */ +#define Tx7 0x20 /* Tx 7 bits/character */ +#define Tx6 0x40 /* Tx 6 bits/character */ +#define Tx8 0x60 /* Tx 8 bits/character */ +#define TxNBITS_MASK 0x60 +#define DTR 0x80 /* DTR */ + +/* Write Register 6 (Sync bits 0-7/SDLC Address Field) */ + +/* Write Register 7 (Sync bits 8-15/SDLC 01111110) */ + +/* Write Register 8 (Transmit Buffer) */ + +/* Write Register 9 (Master Interrupt Control) */ +#define VIS 1 /* Vector Includes Status */ +#define NV 2 /* No Vector */ +#define DLC 4 /* Disable Lower Chain */ +#define MIE 8 /* Master Interrupt Enable */ +#define STATHI 0x10 /* Status high */ +#define SOFTACK 0x20 /* Software Interrupt Acknowledge */ +#define NORESET 0 /* No reset on write to R9 */ +#define CHRB 0x40 /* Reset channel B */ +#define CHRA 0x80 /* Reset channel A */ +#define FHWRES 0xc0 /* Force hardware reset */ + +/* Write Register 10 (Miscellaneous Transmitter/Receiver Control Bits) */ +#define BIT6 1 /* 6 bit/8bit sync */ +#define LOOPMODE 2 /* SDLC Loop mode */ +#define ABUNDER 4 /* Abort/flag on SDLC xmit underrun */ +#define MARKIDLE 8 /* Mark/flag on idle */ +#define GAOP 0x10 /* Go active on poll */ +#define NRZ 0 /* NRZ mode */ +#define NRZI 0x20 /* NRZI mode */ +#define FM1 0x40 /* FM1 (transition = 1) */ +#define FM0 0x60 /* FM0 (transition = 0) */ +#define CRCPS 0x80 /* CRC Preset I/O */ + +/* Write Register 11 (Clock Mode Control) */ +#define TRxCXT 0 /* TRxC = Xtal output */ +#define TRxCTC 1 /* TRxC = Transmit clock */ +#define TRxCBR 2 /* TRxC = BR Generator Output */ +#define TRxCDP 3 /* TRxC = DPLL output */ +#define TRxCOI 4 /* TRxC O/I */ +#define TCRTxCP 0 /* Transmit clock = RTxC pin */ +#define TCTRxCP 8 /* Transmit clock = TRxC pin */ +#define TCBR 0x10 /* Transmit clock = BR Generator output */ +#define TCDPLL 0x18 /* Transmit clock = DPLL output */ +#define RCRTxCP 0 /* Receive clock = RTxC pin */ +#define RCTRxCP 0x20 /* Receive clock = TRxC pin */ +#define RCBR 0x40 /* Receive clock = BR Generator output */ +#define RCDPLL 0x60 /* Receive clock = DPLL output */ +#define RTxCX 0x80 /* RTxC Xtal/No Xtal */ + +/* Write Register 12 (Lower Byte of Baud Rate Generator Time Constant) */ + +/* Write Register 13 (Upper Byte of Baud Rate Generator Time Constant) */ + +/* Write Register 14 (Miscellaneous Control Bits) */ +#define BRENABL 1 /* Baud rate generator enable */ +#define BRSRC 2 /* Baud rate generator source */ +#define DTRREQ 4 /* DTR/Request function */ +#define AUTOECHO 8 /* Auto Echo */ +#define LOOPBAK 0x10 /* Local loopback */ +#define SEARCH 0x20 /* Enter search mode */ +#define RMC 0x40 /* Reset missing clock */ +#define DISDPLL 0x60 /* Disable DPLL */ +#define SSBR 0x80 /* Set DPLL source = BR generator */ +#define SSRTxC 0xa0 /* Set DPLL source = RTxC */ +#define SFMM 0xc0 /* Set FM mode */ +#define SNRZI 0xe0 /* Set NRZI mode */ + +/* Write Register 15 (External/Status Interrupt Control) */ +#define WR7P_EN 1 /* WR7 Prime SDLC Feature Enable */ +#define ZCIE 2 /* Zero count IE */ +#define DCDIE 8 /* DCD IE */ +#define SYNCIE 0x10 /* Sync/hunt IE */ +#define CTSIE 0x20 /* CTS IE */ +#define TxUIE 0x40 /* Tx Underrun/EOM IE */ +#define BRKIE 0x80 /* Break/Abort IE */ + + +/* Read Register 0 (Transmit/Receive Buffer Status and External Status) */ +#define Rx_CH_AV 0x1 /* Rx Character Available */ +#define ZCOUNT 0x2 /* Zero count */ +#define Tx_BUF_EMP 0x4 /* Tx Buffer empty */ +#define DCD 0x8 /* DCD */ +#define SYNC_HUNT 0x10 /* Sync/hunt */ +#define CTS 0x20 /* CTS */ +#define TxEOM 0x40 /* Tx underrun */ +#define BRK_ABRT 0x80 /* Break/Abort */ + +/* Read Register 1 (Special Receive Condition Status) */ +#define ALL_SNT 0x1 /* All sent */ +/* Residue Data for 8 Rx bits/char programmed */ +#define RES3 0x8 /* 0/3 */ +#define RES4 0x4 /* 0/4 */ +#define RES5 0xc /* 0/5 */ +#define RES6 0x2 /* 0/6 */ +#define RES7 0xa /* 0/7 */ +#define RES8 0x6 /* 0/8 */ +#define RES18 0xe /* 1/8 */ +#define RES28 0x0 /* 2/8 */ +/* Special Rx Condition Interrupts */ +#define PAR_ERR 0x10 /* Parity Error */ +#define Rx_OVR 0x20 /* Rx Overrun Error */ +#define FRM_ERR 0x40 /* CRC/Framing Error */ +#define END_FR 0x80 /* End of Frame (SDLC) */ + +/* Read Register 2 (Interrupt Vector (WR2) -- channel A). */ + +/* Read Register 2 (Modified Interrupt Vector -- channel B). */ + +/* Read Register 3 (Interrupt Pending Bits -- channel A only). */ +#define CHBEXT 0x1 /* Channel B Ext/Stat IP */ +#define CHBTxIP 0x2 /* Channel B Tx IP */ +#define CHBRxIP 0x4 /* Channel B Rx IP */ +#define CHAEXT 0x8 /* Channel A Ext/Stat IP */ +#define CHATxIP 0x10 /* Channel A Tx IP */ +#define CHARxIP 0x20 /* Channel A Rx IP */ + +/* Read Register 6 (SDLC FIFO Status and Byte Count LSB) */ + +/* Read Register 7 (SDLC FIFO Status and Byte Count MSB) */ + +/* Read Register 8 (Receive Data) */ + +/* Read Register 10 (Miscellaneous Status Bits) */ +#define ONLOOP 2 /* On loop */ +#define LOOPSEND 0x10 /* Loop sending */ +#define CLK2MIS 0x40 /* Two clocks missing */ +#define CLK1MIS 0x80 /* One clock missing */ + +/* Read Register 12 (Lower Byte of Baud Rate Generator Constant (WR12)) */ + +/* Read Register 13 (Upper Byte of Baud Rate Generator Constant (WR13) */ + +/* Read Register 15 (External/Status Interrupt Control (WR15)) */ + +#endif /* _SERIAL_ZS_H */ |