diff options
Diffstat (limited to 'drivers/tty/serial/amba-pl011.c')
| -rw-r--r-- | drivers/tty/serial/amba-pl011.c | 84 |
1 files changed, 46 insertions, 38 deletions
diff --git a/drivers/tty/serial/amba-pl011.c b/drivers/tty/serial/amba-pl011.c index 7203864992a..d58783d364e 100644 --- a/drivers/tty/serial/amba-pl011.c +++ b/drivers/tty/serial/amba-pl011.c @@ -112,8 +112,6 @@ static struct vendor_data vendor_st = { .get_fifosize = get_fifosize_st, }; -static struct uart_amba_port *amba_ports[UART_NR]; - /* Deals with DMA transactions */ struct pl011_sgbuf { @@ -969,6 +967,8 @@ static void pl011_dma_rx_poll(unsigned long args) spin_lock_irqsave(&uap->port.lock, flags); pl011_dma_rx_stop(uap); + uap->im |= UART011_RXIM; + writew(uap->im, uap->port.membase + UART011_IMSC); spin_unlock_irqrestore(&uap->port.lock, flags); uap->dmarx.running = false; @@ -1216,8 +1216,8 @@ __acquires(&uap->port.lock) dev_dbg(uap->port.dev, "could not trigger RX DMA job " "fall back to interrupt mode again\n"); uap->im |= UART011_RXIM; + writew(uap->im, uap->port.membase + UART011_IMSC); } else { - uap->im &= ~UART011_RXIM; #ifdef CONFIG_DMA_ENGINE /* Start Rx DMA poll */ if (uap->dmarx.poll_rate) { @@ -1229,8 +1229,6 @@ __acquires(&uap->port.lock) } #endif } - - writew(uap->im, uap->port.membase + UART011_IMSC); } spin_lock(&uap->port.lock); } @@ -1513,10 +1511,25 @@ static int pl011_hwinit(struct uart_port *port) return retval; } +static void pl011_write_lcr_h(struct uart_amba_port *uap, unsigned int lcr_h) +{ + writew(lcr_h, uap->port.membase + uap->lcrh_rx); + if (uap->lcrh_rx != uap->lcrh_tx) { + int i; + /* + * Wait 10 PCLKs before writing LCRH_TX register, + * to get this delay write read only register 10 times + */ + for (i = 0; i < 10; ++i) + writew(0xff, uap->port.membase + UART011_MIS); + writew(lcr_h, uap->port.membase + uap->lcrh_tx); + } +} + static int pl011_startup(struct uart_port *port) { struct uart_amba_port *uap = (struct uart_amba_port *)port; - unsigned int cr; + unsigned int cr, lcr_h, fbrd, ibrd; int retval; retval = pl011_hwinit(port); @@ -1535,32 +1548,36 @@ static int pl011_startup(struct uart_port *port) writew(uap->vendor->ifls, uap->port.membase + UART011_IFLS); /* - * Provoke TX FIFO interrupt into asserting. + * Provoke TX FIFO interrupt into asserting. Taking care to preserve + * baud rate and data format specified by FBRD, IBRD and LCRH as the + * UART may already be in use as a console. */ + spin_lock_irq(&uap->port.lock); + + fbrd = readw(uap->port.membase + UART011_FBRD); + ibrd = readw(uap->port.membase + UART011_IBRD); + lcr_h = readw(uap->port.membase + uap->lcrh_rx); + cr = UART01x_CR_UARTEN | UART011_CR_TXE | UART011_CR_LBE; writew(cr, uap->port.membase + UART011_CR); writew(0, uap->port.membase + UART011_FBRD); writew(1, uap->port.membase + UART011_IBRD); - writew(0, uap->port.membase + uap->lcrh_rx); - if (uap->lcrh_tx != uap->lcrh_rx) { - int i; - /* - * Wait 10 PCLKs before writing LCRH_TX register, - * to get this delay write read only register 10 times - */ - for (i = 0; i < 10; ++i) - writew(0xff, uap->port.membase + UART011_MIS); - writew(0, uap->port.membase + uap->lcrh_tx); - } + pl011_write_lcr_h(uap, 0); writew(0, uap->port.membase + UART01x_DR); while (readw(uap->port.membase + UART01x_FR) & UART01x_FR_BUSY) barrier(); + writew(fbrd, uap->port.membase + UART011_FBRD); + writew(ibrd, uap->port.membase + UART011_IBRD); + pl011_write_lcr_h(uap, lcr_h); + /* restore RTS and DTR */ cr = uap->old_cr & (UART011_CR_RTS | UART011_CR_DTR); cr |= UART01x_CR_UARTEN | UART011_CR_RXE | UART011_CR_TXE; writew(cr, uap->port.membase + UART011_CR); + spin_unlock_irq(&uap->port.lock); + /* * initialise the old status of the modem signals */ @@ -1629,11 +1646,13 @@ static void pl011_shutdown(struct uart_port *port) * it during startup(). */ uap->autorts = false; + spin_lock_irq(&uap->port.lock); cr = readw(uap->port.membase + UART011_CR); uap->old_cr = cr; cr &= UART011_CR_RTS | UART011_CR_DTR; cr |= UART01x_CR_UARTEN | UART011_CR_TXE; writew(cr, uap->port.membase + UART011_CR); + spin_unlock_irq(&uap->port.lock); /* * disable break condition and fifos @@ -1797,17 +1816,7 @@ pl011_set_termios(struct uart_port *port, struct ktermios *termios, * UART011_FBRD & UART011_IBRD. * ----------^----------^----------^----------^----- */ - writew(lcr_h, port->membase + uap->lcrh_rx); - if (uap->lcrh_rx != uap->lcrh_tx) { - int i; - /* - * Wait 10 PCLKs before writing LCRH_TX register, - * to get this delay write read only register 10 times - */ - for (i = 0; i < 10; ++i) - writew(0xff, uap->port.membase + UART011_MIS); - writew(lcr_h, port->membase + uap->lcrh_tx); - } + pl011_write_lcr_h(uap, lcr_h); writew(old_cr, port->membase + UART011_CR); spin_unlock_irqrestore(&port->lock, flags); @@ -2169,10 +2178,10 @@ static int pl011_remove(struct amba_device *dev) return 0; } -#ifdef CONFIG_PM -static int pl011_suspend(struct amba_device *dev, pm_message_t state) +#ifdef CONFIG_PM_SLEEP +static int pl011_suspend(struct device *dev) { - struct uart_amba_port *uap = amba_get_drvdata(dev); + struct uart_amba_port *uap = dev_get_drvdata(dev); if (!uap) return -EINVAL; @@ -2180,9 +2189,9 @@ static int pl011_suspend(struct amba_device *dev, pm_message_t state) return uart_suspend_port(&amba_reg, &uap->port); } -static int pl011_resume(struct amba_device *dev) +static int pl011_resume(struct device *dev) { - struct uart_amba_port *uap = amba_get_drvdata(dev); + struct uart_amba_port *uap = dev_get_drvdata(dev); if (!uap) return -EINVAL; @@ -2191,6 +2200,8 @@ static int pl011_resume(struct amba_device *dev) } #endif +static SIMPLE_DEV_PM_OPS(pl011_dev_pm_ops, pl011_suspend, pl011_resume); + static struct amba_id pl011_ids[] = { { .id = 0x00041011, @@ -2210,14 +2221,11 @@ MODULE_DEVICE_TABLE(amba, pl011_ids); static struct amba_driver pl011_driver = { .drv = { .name = "uart-pl011", + .pm = &pl011_dev_pm_ops, }, .id_table = pl011_ids, .probe = pl011_probe, .remove = pl011_remove, -#ifdef CONFIG_PM - .suspend = pl011_suspend, - .resume = pl011_resume, -#endif }; static int __init pl011_init(void) |