24 files changed, 370 insertions, 342 deletions

diff --git a/drivers/tty/serial/8250.c b/drivers/tty/serial/8250.c
index b4129f53fb1..f2dfec82faf 100644
--- a/drivers/tty/serial/8250.c
+++ b/drivers/tty/serial/8250.c
@@ -81,7 +81,7 @@ static unsigned int skip_txen_test; /* force skip of txen test at init time */
 #define DEBUG_INTR(fmt...)	do { } while (0)
 #endif
 
-#define PASS_LIMIT	256
+#define PASS_LIMIT	512
 
 #define BOTH_EMPTY 	(UART_LSR_TEMT | UART_LSR_THRE)
 
@@ -1107,7 +1107,7 @@ static void autoconfig_16550a(struct uart_8250_port *up)
 			 */
 			DEBUG_AUTOCONF("Xscale ");
 			up->port.type = PORT_XSCALE;
-			up->capabilities |= UART_CAP_UUE;
+			up->capabilities |= UART_CAP_UUE | UART_CAP_RTOIE;
 			return;
 		}
 	} else {
diff --git a/drivers/tty/serial/8250_pci.c b/drivers/tty/serial/8250_pci.c
index f41b4259ecd..6b887d90a20 100644
--- a/drivers/tty/serial/8250_pci.c
+++ b/drivers/tty/serial/8250_pci.c
@@ -39,6 +39,7 @@ struct pci_serial_quirk {
 	u32	device;
 	u32	subvendor;
 	u32	subdevice;
+	int	(*probe)(struct pci_dev *dev);
 	int	(*init)(struct pci_dev *dev);
 	int	(*setup)(struct serial_private *,
 			 const struct pciserial_board *,
@@ -56,6 +57,9 @@ struct serial_private {
 	int			line[0];
 };
 
+static int pci_default_setup(struct serial_private*,
+	  const struct pciserial_board*, struct uart_port*, int);
+
 static void moan_device(const char *str, struct pci_dev *dev)
 {
 	printk(KERN_WARNING
@@ -571,6 +575,28 @@ static const struct timedia_struct {
 	{ 8, timedia_eight_port }
 };
 
+/*
+ * There are nearly 70 different Timedia/SUNIX PCI serial devices.  Instead of
+ * listing them individually, this driver merely grabs them all with
+ * PCI_ANY_ID.  Some of these devices, however, also feature a parallel port,
+ * and should be left free to be claimed by parport_serial instead.
+ */
+static int pci_timedia_probe(struct pci_dev *dev)
+{
+	/*
+	 * Check the third digit of the subdevice ID
+	 * (0,2,3,5,6: serial only -- 7,8,9: serial + parallel)
+	 */
+	if ((dev->subsystem_device & 0x00f0) >= 0x70) {
+		dev_info(&dev->dev,
+			"ignoring Timedia subdevice %04x for parport_serial\n",
+			dev->subsystem_device);
+		return -ENODEV;
+	}
+
+	return 0;
+}
+
 static int pci_timedia_init(struct pci_dev *dev)
 {
 	const unsigned short *ids;
@@ -743,7 +769,7 @@ pci_ni8430_setup(struct serial_private *priv,
 	len =  pci_resource_len(priv->dev, bar);
 	p = ioremap_nocache(base, len);
 
-	/* enable the transciever */
+	/* enable the transceiver */
 	writeb(readb(p + offset + NI8430_PORTCON) | NI8430_PORTCON_TXVR_ENABLE,
 	       p + offset + NI8430_PORTCON);
 
@@ -752,6 +778,62 @@ pci_ni8430_setup(struct serial_private *priv,
 	return setup_port(priv, port, bar, offset, board->reg_shift);
 }
 
+static int pci_netmos_9900_setup(struct serial_private *priv,
+				const struct pciserial_board *board,
+				struct uart_port *port, int idx)
+{
+	unsigned int bar;
+
+	if ((priv->dev->subsystem_device & 0xff00) == 0x3000) {
+		/* netmos apparently orders BARs by datasheet layout, so serial
+		 * ports get BARs 0 and 3 (or 1 and 4 for memmapped)
+		 */
+		bar = 3 * idx;
+
+		return setup_port(priv, port, bar, 0, board->reg_shift);
+	} else {
+		return pci_default_setup(priv, board, port, idx);
+	}
+}
+
+/* the 99xx series comes with a range of device IDs and a variety
+ * of capabilities:
+ *
+ * 9900 has varying capabilities and can cascade to sub-controllers
+ *   (cascading should be purely internal)
+ * 9904 is hardwired with 4 serial ports
+ * 9912 and 9922 are hardwired with 2 serial ports
+ */
+static int pci_netmos_9900_numports(struct pci_dev *dev)
+{
+	unsigned int c = dev->class;
+	unsigned int pi;
+	unsigned short sub_serports;
+
+	pi = (c & 0xff);
+
+	if (pi == 2) {
+		return 1;
+	} else if ((pi == 0) &&
+			   (dev->device == PCI_DEVICE_ID_NETMOS_9900)) {
+		/* two possibilities: 0x30ps encodes number of parallel and
+		 * serial ports, or 0x1000 indicates *something*. This is not
+		 * immediately obvious, since the 2s1p+4s configuration seems
+		 * to offer all functionality on functions 0..2, while still
+		 * advertising the same function 3 as the 4s+2s1p config.
+		 */
+		sub_serports = dev->subsystem_device & 0xf;
+		if (sub_serports > 0) {
+			return sub_serports;
+		} else {
+			printk(KERN_NOTICE "NetMos/Mostech serial driver ignoring port on ambiguous config.\n");
+			return 0;
+		}
+	}
+
+	moan_device("unknown NetMos/Mostech program interface", dev);
+	return 0;
+}
 
 static int pci_netmos_init(struct pci_dev *dev)
 {
@@ -761,12 +843,28 @@ static int pci_netmos_init(struct pci_dev *dev)
 	if ((dev->device == PCI_DEVICE_ID_NETMOS_9901) ||
 		(dev->device == PCI_DEVICE_ID_NETMOS_9865))
 		return 0;
+
 	if (dev->subsystem_vendor == PCI_VENDOR_ID_IBM &&
 			dev->subsystem_device == 0x0299)
 		return 0;
 
+	switch (dev->device) { /* FALLTHROUGH on all */
+		case PCI_DEVICE_ID_NETMOS_9904:
+		case PCI_DEVICE_ID_NETMOS_9912:
+		case PCI_DEVICE_ID_NETMOS_9922:
+		case PCI_DEVICE_ID_NETMOS_9900:
+			num_serial = pci_netmos_9900_numports(dev);
+			break;
+
+		default:
+			if (num_serial == 0 ) {
+				moan_device("unknown NetMos/Mostech device", dev);
+			}
+	}
+
 	if (num_serial == 0)
 		return -ENODEV;
+
 	return num_serial;
 }
 
@@ -1396,6 +1494,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.device		= PCI_DEVICE_ID_TIMEDIA_1889,
 		.subvendor	= PCI_VENDOR_ID_TIMEDIA,
 		.subdevice	= PCI_ANY_ID,
+		.probe		= pci_timedia_probe,
 		.init		= pci_timedia_init,
 		.setup		= pci_timedia_setup,
 	},
@@ -1426,7 +1525,7 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = {
 		.subvendor	= PCI_ANY_ID,
 		.subdevice	= PCI_ANY_ID,
 		.init		= pci_netmos_init,
-		.setup		= pci_default_setup,
+		.setup		= pci_netmos_9900_setup,
 	},
 	/*
 	 * For Oxford Semiconductor Tornado based devices
@@ -1703,6 +1802,7 @@ enum pci_board_num_t {
 	pbn_ADDIDATA_PCIe_8_3906250,
 	pbn_ce4100_1_115200,
 	pbn_omegapci,
+	pbn_NETMOS9900_2s_115200,
 };
 
 /*
@@ -2404,6 +2504,11 @@ static struct pciserial_board pci_boards[] __devinitdata = {
 		.base_baud	= 115200,
 		.uart_offset	= 0x200,
 	},
+	[pbn_NETMOS9900_2s_115200] = {
+		.flags		= FL_BASE0,
+		.num_ports	= 2,
+		.base_baud	= 115200,
+	},
 };
 
 static const struct pci_device_id softmodem_blacklist[] = {
@@ -2640,11 +2745,19 @@ EXPORT_SYMBOL_GPL(pciserial_resume_ports);
 static int __devinit
 pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
 {
+	struct pci_serial_quirk *quirk;
 	struct serial_private *priv;
 	const struct pciserial_board *board;
 	struct pciserial_board tmp;
 	int rc;
 
+	quirk = find_quirk(dev);
+	if (quirk->probe) {
+		rc = quirk->probe(dev);
+		if (rc)
+			return rc;
+	}
+
 	if (ent->driver_data >= ARRAY_SIZE(pci_boards)) {
 		printk(KERN_ERR "pci_init_one: invalid driver_data: %ld\n",
 			ent->driver_data);
@@ -2654,6 +2767,7 @@ pciserial_init_one(struct pci_dev *dev, const struct pci_device_id *ent)
 	board = &pci_boards[ent->driver_data];
 
 	rc = pci_enable_device(dev);
+	pci_save_state(dev);
 	if (rc)
 		return rc;
 
@@ -3885,6 +3999,27 @@ static struct pci_device_id serial_pci_tbl[] = {
 		0xA000, 0x1000,
 		0, 0, pbn_b0_1_115200 },
 
+	/* the 9901 is a rebranded 9912 */
+	{	PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9912,
+		0xA000, 0x1000,
+		0, 0, pbn_b0_1_115200 },
+
+	{	PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9922,
+		0xA000, 0x1000,
+		0, 0, pbn_b0_1_115200 },
+
+	{	PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9904,
+		0xA000, 0x1000,
+		0, 0, pbn_b0_1_115200 },
+
+	{	PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9900,
+		0xA000, 0x1000,
+		0, 0, pbn_b0_1_115200 },
+
+	{	PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9900,
+		0xA000, 0x3002,
+		0, 0, pbn_NETMOS9900_2s_115200 },
+
 	/*
 	 * Best Connectivity PCI Multi I/O cards
 	 */
@@ -3927,6 +4062,51 @@ static struct pci_device_id serial_pci_tbl[] = {
 	{ 0, }
 };
 
+static pci_ers_result_t serial8250_io_error_detected(struct pci_dev *dev,
+						pci_channel_state_t state)
+{
+	struct serial_private *priv = pci_get_drvdata(dev);
+
+	if (state == pci_channel_io_perm_failure)
+		return PCI_ERS_RESULT_DISCONNECT;
+
+	if (priv)
+		pciserial_suspend_ports(priv);
+
+	pci_disable_device(dev);
+
+	return PCI_ERS_RESULT_NEED_RESET;
+}
+
+static pci_ers_result_t serial8250_io_slot_reset(struct pci_dev *dev)
+{
+	int rc;
+
+	rc = pci_enable_device(dev);
+
+	if (rc)
+		return PCI_ERS_RESULT_DISCONNECT;
+
+	pci_restore_state(dev);
+	pci_save_state(dev);
+
+	return PCI_ERS_RESULT_RECOVERED;
+}
+
+static void serial8250_io_resume(struct pci_dev *dev)
+{
+	struct serial_private *priv = pci_get_drvdata(dev);
+
+	if (priv)
+		pciserial_resume_ports(priv);
+}
+
+static struct pci_error_handlers serial8250_err_handler = {
+	.error_detected = serial8250_io_error_detected,
+	.slot_reset = serial8250_io_slot_reset,
+	.resume = serial8250_io_resume,
+};
+
 static struct pci_driver serial_pci_driver = {
 	.name		= "serial",
 	.probe		= pciserial_init_one,
@@ -3936,6 +4116,7 @@ static struct pci_driver serial_pci_driver = {
 	.resume		= pciserial_resume_one,
 #endif
 	.id_table	= serial_pci_tbl,
+	.err_handler	= &serial8250_err_handler,
 };
 
 static int __init serial8250_pci_init(void)
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 636144cea93..cb40b82daf3 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -457,7 +457,6 @@ config SERIAL_SAMSUNG_UARTS_4
 config SERIAL_SAMSUNG_UARTS
 	int
 	depends on ARM && PLAT_SAMSUNG
-	default 2 if ARCH_S3C2400
 	default 6 if ARCH_S5P6450
 	default 4 if SERIAL_SAMSUNG_UARTS_4
 	default 3
@@ -489,13 +488,6 @@ config SERIAL_SAMSUNG_CONSOLE
 	  your boot loader about how to pass options to the kernel at
 	  boot time.)
 
-config SERIAL_S3C2400
-	tristate "Samsung S3C2410 Serial port support"
-	depends on ARM && SERIAL_SAMSUNG && CPU_S3C2400
-	default y if CPU_S3C2400
-	help
-	  Serial port support for the Samsung S3C2400 SoC
-
 config SERIAL_S3C2410
 	tristate "Samsung S3C2410 Serial port support"
 	depends on SERIAL_SAMSUNG && CPU_S3C2410
@@ -519,13 +511,6 @@ config SERIAL_S3C2440
 	help
 	  Serial port support for the Samsung S3C2440, S3C2416 and S3C2442 SoC
 
-config SERIAL_S3C24A0
-	tristate "Samsung S3C24A0 Serial port support"
-	depends on SERIAL_SAMSUNG && CPU_S3C24A0
-	default y if CPU_S3C24A0
-	help
-	  Serial port support for the Samsung S3C24A0 SoC
-
 config SERIAL_S3C6400
 	tristate "Samsung S3C6400/S3C6410/S5P6440/S5P6450/S5PC100 Serial port support"
 	depends on SERIAL_SAMSUNG && (CPU_S3C6400 || CPU_S3C6410 || CPU_S5P6440 || CPU_S5P6450 || CPU_S5PC100)
@@ -1419,7 +1404,7 @@ config SERIAL_SC26XX
 
 config SERIAL_SC26XX_CONSOLE
 	bool "Console on SC2681/SC2692 serial port"
-	depends on SERIAL_SC26XX
+	depends on SERIAL_SC26XX=y
 	select SERIAL_CORE_CONSOLE
 	help
 	  Support for Console on SC2681/SC2692 serial ports.
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index cb2628fee4c..83b4da6a106 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -38,11 +38,9 @@ obj-$(CONFIG_SERIAL_BCM63XX) += bcm63xx_uart.o
 obj-$(CONFIG_SERIAL_BFIN) += bfin_5xx.o
 obj-$(CONFIG_SERIAL_BFIN_SPORT) += bfin_sport_uart.o
 obj-$(CONFIG_SERIAL_SAMSUNG) += samsung.o
-obj-$(CONFIG_SERIAL_S3C2400) += s3c2400.o
 obj-$(CONFIG_SERIAL_S3C2410) += s3c2410.o
 obj-$(CONFIG_SERIAL_S3C2412) += s3c2412.o
 obj-$(CONFIG_SERIAL_S3C2440) += s3c2440.o
-obj-$(CONFIG_SERIAL_S3C24A0) += s3c24a0.o
 obj-$(CONFIG_SERIAL_S3C6400) += s3c6400.o
 obj-$(CONFIG_SERIAL_S5PV210) += s5pv210.o
 obj-$(CONFIG_SERIAL_MAX3100) += max3100.o
diff --git a/drivers/tty/serial/bfin_5xx.c b/drivers/tty/serial/bfin_5xx.c
index 9b1ff2b6bb3..ff6979181ac 100644
--- a/drivers/tty/serial/bfin_5xx.c
+++ b/drivers/tty/serial/bfin_5xx.c
@@ -1304,8 +1304,7 @@ static int bfin_serial_probe(struct platform_device *pdev)
 			goto out_error_free_peripherals;
 		}
 
-		uart->port.membase = ioremap(res->start,
-			res->end - res->start);
+		uart->port.membase = ioremap(res->start, resource_size(res));
 		if (!uart->port.membase) {
 			dev_err(&pdev->dev, "Cannot map uart IO\n");
 			ret = -ENXIO;
@@ -1483,7 +1482,7 @@ static int bfin_earlyprintk_probe(struct platform_device *pdev)
 	}
 
 	bfin_earlyprintk_port.port.membase = ioremap(res->start,
-			res->end - res->start);
+						     resource_size(res));
 	if (!bfin_earlyprintk_port.port.membase) {
 		dev_err(&pdev->dev, "Cannot map uart IO\n");
 		ret = -ENXIO;
diff --git a/drivers/tty/serial/dz.c b/drivers/tty/serial/dz.c
index 57421d77632..ddc487a2d42 100644
--- a/drivers/tty/serial/dz.c
+++ b/drivers/tty/serial/dz.c
@@ -48,7 +48,7 @@
 #include <linux/sysrq.h>
 #include <linux/tty.h>
 
-#include <asm/atomic.h>
+#include <linux/atomic.h>
 #include <asm/bootinfo.h>
 #include <asm/io.h>
 #include <asm/system.h>
diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c
index a54473123e0..827db765459 100644
--- a/drivers/tty/serial/imx.c
+++ b/drivers/tty/serial/imx.c
@@ -45,10 +45,11 @@
 #include <linux/delay.h>
 #include <linux/rational.h>
 #include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
 
 #include <asm/io.h>
 #include <asm/irq.h>
-#include <mach/hardware.h>
 #include <mach/imx-uart.h>
 
 /* Register definitions */
@@ -66,8 +67,9 @@
 #define UBIR  0xa4 /* BRM Incremental Register */
 #define UBMR  0xa8 /* BRM Modulator Register */
 #define UBRC  0xac /* Baud Rate Count Register */
-#define MX2_ONEMS 0xb0 /* One Millisecond register */
-#define UTS (cpu_is_mx1() ? 0xd0 : 0xb4) /* UART Test Register */
+#define IMX21_ONEMS 0xb0 /* One Millisecond register */
+#define IMX1_UTS 0xd0 /* UART Test Register on i.mx1 */
+#define IMX21_UTS 0xb4 /* UART Test Register on all other i.mx*/
 
 /* UART Control Register Bit Fields.*/
 #define  URXD_CHARRDY    (1<<15)
@@ -87,7 +89,7 @@
 #define  UCR1_RTSDEN     (1<<5)	 /* RTS delta interrupt enable */
 #define  UCR1_SNDBRK     (1<<4)	 /* Send break */
 #define  UCR1_TDMAEN     (1<<3)	 /* Transmitter ready DMA enable */
-#define  MX1_UCR1_UARTCLKEN  (1<<2)	 /* UART clock enabled, mx1 only */
+#define  IMX1_UCR1_UARTCLKEN  (1<<2)  /* UART clock enabled, i.mx1 only */
 #define  UCR1_DOZE       (1<<1)	 /* Doze */
 #define  UCR1_UARTEN     (1<<0)	 /* UART enabled */
 #define  UCR2_ESCI     	 (1<<15) /* Escape seq interrupt enable */
@@ -113,9 +115,7 @@
 #define  UCR3_RXDSEN	 (1<<6)  /* Receive status interrupt enable */
 #define  UCR3_AIRINTEN   (1<<5)  /* Async IR wake interrupt enable */
 #define  UCR3_AWAKEN	 (1<<4)  /* Async wake interrupt enable */
-#define  MX1_UCR3_REF25 	 (1<<3)  /* Ref freq 25 MHz, only on mx1 */
-#define  MX1_UCR3_REF30 	 (1<<2)  /* Ref Freq 30 MHz, only on mx1 */
-#define  MX2_UCR3_RXDMUXSEL	 (1<<2)  /* RXD Muxed Input Select, on mx2/mx3 */
+#define  IMX21_UCR3_RXDMUXSEL	 (1<<2)  /* RXD Muxed Input Select */
 #define  UCR3_INVT  	 (1<<1)  /* Inverted Infrared transmission */
 #define  UCR3_BPEN  	 (1<<0)  /* Preset registers enable */
 #define  UCR4_CTSTL_SHF  10      /* CTS trigger level shift */
@@ -181,6 +181,18 @@
 
 #define UART_NR 8
 
+/* i.mx21 type uart runs on all i.mx except i.mx1 */
+enum imx_uart_type {
+	IMX1_UART,
+	IMX21_UART,
+};
+
+/* device type dependent stuff */
+struct imx_uart_data {
+	unsigned uts_reg;
+	enum imx_uart_type devtype;
+};
+
 struct imx_port {
 	struct uart_port	port;
 	struct timer_list	timer;
@@ -192,6 +204,7 @@ struct imx_port {
 	unsigned int		irda_inv_tx:1;
 	unsigned short		trcv_delay; /* transceiver delay */
 	struct clk		*clk;
+	struct imx_uart_data	*devdata;
 };
 
 #ifdef CONFIG_IRDA
@@ -200,6 +213,52 @@ struct imx_port {
 #define USE_IRDA(sport)	(0)
 #endif
 
+static struct imx_uart_data imx_uart_devdata[] = {
+	[IMX1_UART] = {
+		.uts_reg = IMX1_UTS,
+		.devtype = IMX1_UART,
+	},
+	[IMX21_UART] = {
+		.uts_reg = IMX21_UTS,
+		.devtype = IMX21_UART,
+	},
+};
+
+static struct platform_device_id imx_uart_devtype[] = {
+	{
+		.name = "imx1-uart",
+		.driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX1_UART],
+	}, {
+		.name = "imx21-uart",
+		.driver_data = (kernel_ulong_t) &imx_uart_devdata[IMX21_UART],
+	}, {
+		/* sentinel */
+	}
+};
+MODULE_DEVICE_TABLE(platform, imx_uart_devtype);
+
+static struct of_device_id imx_uart_dt_ids[] = {
+	{ .compatible = "fsl,imx1-uart", .data = &imx_uart_devdata[IMX1_UART], },
+	{ .compatible = "fsl,imx21-uart", .data = &imx_uart_devdata[IMX21_UART], },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, imx_uart_dt_ids);
+
+static inline unsigned uts_reg(struct imx_port *sport)
+{
+	return sport->devdata->uts_reg;
+}
+
+static inline int is_imx1_uart(struct imx_port *sport)
+{
+	return sport->devdata->devtype == IMX1_UART;
+}
+
+static inline int is_imx21_uart(struct imx_port *sport)
+{
+	return sport->devdata->devtype == IMX21_UART;
+}
+
 /*
  * Handle any change of modem status signal since we were last called.
  */
@@ -326,7 +385,8 @@ static inline void imx_transmit_buffer(struct imx_port *sport)
 	struct circ_buf *xmit = &sport->port.state->xmit;
 
 	while (!uart_circ_empty(xmit) &&
-			!(readl(sport->port.membase + UTS) & UTS_TXFULL)) {
+			!(readl(sport->port.membase + uts_reg(sport))
+				& UTS_TXFULL)) {
 		/* send xmit->buf[xmit->tail]
 		 * out the port here */
 		writel(xmit->buf[xmit->tail], sport->port.membase + URTX0);
@@ -373,7 +433,7 @@ static void imx_start_tx(struct uart_port *port)
 		writel(temp, sport->port.membase + UCR4);
 	}
 
-	if (readl(sport->port.membase + UTS) & UTS_TXEMPTY)
+	if (readl(sport->port.membase + uts_reg(sport)) & UTS_TXEMPTY)
 		imx_transmit_buffer(sport);
 }
 
@@ -689,9 +749,9 @@ static int imx_startup(struct uart_port *port)
 		}
 	}
 
-	if (!cpu_is_mx1()) {
+	if (is_imx21_uart(sport)) {
 		temp = readl(sport->port.membase + UCR3);
-		temp |= MX2_UCR3_RXDMUXSEL;
+		temp |= IMX21_UCR3_RXDMUXSEL;
 		writel(temp, sport->port.membase + UCR3);
 	}
 
@@ -923,9 +983,9 @@ imx_set_termios(struct uart_port *port, struct ktermios *termios,
 	writel(num, sport->port.membase + UBIR);
 	writel(denom, sport->port.membase + UBMR);
 
-	if (!cpu_is_mx1())
+	if (is_imx21_uart(sport))
 		writel(sport->port.uartclk / div / 1000,
-				sport->port.membase + MX2_ONEMS);
+				sport->port.membase + IMX21_ONEMS);
 
 	writel(old_ucr1, sport->port.membase + UCR1);
 
@@ -954,7 +1014,7 @@ static void imx_release_port(struct uart_port *port)
 	struct resource *mmres;
 
 	mmres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	release_mem_region(mmres->start, mmres->end - mmres->start + 1);
+	release_mem_region(mmres->start, resource_size(mmres));
 }
 
 /*
@@ -970,8 +1030,7 @@ static int imx_request_port(struct uart_port *port)
 	if (!mmres)
 		return -ENODEV;
 
-	ret = request_mem_region(mmres->start, mmres->end - mmres->start + 1,
-			"imx-uart");
+	ret = request_mem_region(mmres->start, resource_size(mmres), "imx-uart");
 
 	return  ret ? 0 : -EBUSY;
 }
@@ -1042,7 +1101,7 @@ static void imx_console_putchar(struct uart_port *port, int ch)
 {
 	struct imx_port *sport = (struct imx_port *)port;
 
-	while (readl(sport->port.membase + UTS) & UTS_TXFULL)
+	while (readl(sport->port.membase + uts_reg(sport)) & UTS_TXFULL)
 		barrier();
 
 	writel(ch, sport->port.membase + URTX0);
@@ -1063,8 +1122,8 @@ imx_console_write(struct console *co, const char *s, unsigned int count)
 	ucr1 = old_ucr1 = readl(sport->port.membase + UCR1);
 	old_ucr2 = readl(sport->port.membase + UCR2);
 
-	if (cpu_is_mx1())
-		ucr1 |= MX1_UCR1_UARTCLKEN;
+	if (is_imx1_uart(sport))
+		ucr1 |= IMX1_UCR1_UARTCLKEN;
 	ucr1 |= UCR1_UARTEN;
 	ucr1 &= ~(UCR1_TXMPTYEN | UCR1_RRDYEN | UCR1_RTSDEN);
 
@@ -1223,6 +1282,63 @@ static int serial_imx_resume(struct platform_device *dev)
 	return 0;
 }
 
+#ifdef CONFIG_OF
+static int serial_imx_probe_dt(struct imx_port *sport,
+		struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	const struct of_device_id *of_id =
+			of_match_device(imx_uart_dt_ids, &pdev->dev);
+	int ret;
+
+	if (!np)
+		return -ENODEV;
+
+	ret = of_alias_get_id(np, "serial");
+	if (ret < 0) {
+		pr_err("%s: failed to get alias id, errno %d\n",
+			__func__, ret);
+		return -ENODEV;
+	} else {
+		sport->port.line = ret;
+	}
+
+	if (of_get_property(np, "fsl,uart-has-rtscts", NULL))
+		sport->have_rtscts = 1;
+
+	if (of_get_property(np, "fsl,irda-mode", NULL))
+		sport->use_irda = 1;
+
+	sport->devdata = of_id->data;
+
+	return 0;
+}
+#else
+static inline int serial_imx_probe_dt(struct imx_port *sport,
+		struct platform_device *pdev)
+{
+	return -ENODEV;
+}
+#endif
+
+static void serial_imx_probe_pdata(struct imx_port *sport,
+		struct platform_device *pdev)
+{
+	struct imxuart_platform_data *pdata = pdev->dev.platform_data;
+
+	sport->port.line = pdev->id;
+	sport->devdata = (struct imx_uart_data	*) pdev->id_entry->driver_data;
+
+	if (!pdata)
+		return;
+
+	if (pdata->flags & IMXUART_HAVE_RTSCTS)
+		sport->have_rtscts = 1;
+
+	if (pdata->flags & IMXUART_IRDA)
+		sport->use_irda = 1;
+}
+
 static int serial_imx_probe(struct platform_device *pdev)
 {
 	struct imx_port *sport;
@@ -1235,6 +1351,10 @@ static int serial_imx_probe(struct platform_device *pdev)
 	if (!sport)
 		return -ENOMEM;
 
+	ret = serial_imx_probe_dt(sport, pdev);
+	if (ret == -ENODEV)
+		serial_imx_probe_pdata(sport, pdev);
+
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 	if (!res) {
 		ret = -ENODEV;
@@ -1259,7 +1379,6 @@ static int serial_imx_probe(struct platform_device *pdev)
 	sport->port.fifosize = 32;
 	sport->port.ops = &imx_pops;
 	sport->port.flags = UPF_BOOT_AUTOCONF;
-	sport->port.line = pdev->id;
 	init_timer(&sport->timer);
 	sport->timer.function = imx_timeout;
 	sport->timer.data     = (unsigned long)sport;
@@ -1273,17 +1392,9 @@ static int serial_imx_probe(struct platform_device *pdev)
 
 	sport->port.uartclk = clk_get_rate(sport->clk);
 
-	imx_ports[pdev->id] = sport;
+	imx_ports[sport->port.line] = sport;
 
 	pdata = pdev->dev.platform_data;
-	if (pdata && (pdata->flags & IMXUART_HAVE_RTSCTS))
-		sport->have_rtscts = 1;
-
-#ifdef CONFIG_IRDA
-	if (pdata && (pdata->flags & IMXUART_IRDA))
-		sport->use_irda = 1;
-#endif
-
 	if (pdata && pdata->init) {
 		ret = pdata->init(pdev);
 		if (ret)
@@ -1341,9 +1452,11 @@ static struct platform_driver serial_imx_driver = {
 
 	.suspend	= serial_imx_suspend,
 	.resume		= serial_imx_resume,
+	.id_table	= imx_uart_devtype,
 	.driver		= {
 		.name	= "imx-uart",
 		.owner	= THIS_MODULE,
+		.of_match_table = imx_uart_dt_ids,
 	},
 };
 
diff --git a/drivers/tty/serial/m32r_sio.c b/drivers/tty/serial/m32r_sio.c
index 84db7321cce..8e07517f8ac 100644
--- a/drivers/tty/serial/m32r_sio.c
+++ b/drivers/tty/serial/m32r_sio.c
@@ -892,7 +892,7 @@ static int m32r_sio_request_port(struct uart_port *port)
 	 * If we have a mapbase, then request that as well.
 	 */
 	if (ret == 0 && up->port.flags & UPF_IOREMAP) {
-		int size = res->end - res->start + 1;
+		int size = resource_size(res);
 
 		up->port.membase = ioremap(up->port.mapbase, size);
 		if (!up->port.membase)
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
index 47cadf47414..c37df8d0fa2 100644
--- a/drivers/tty/serial/omap-serial.c
+++ b/drivers/tty/serial/omap-serial.c
@@ -1241,8 +1241,8 @@ static int serial_omap_probe(struct platform_device *pdev)
 		return -ENODEV;
 	}
 
-	if (!request_mem_region(mem->start, (mem->end - mem->start) + 1,
-				     pdev->dev.driver->name)) {
+	if (!request_mem_region(mem->start, resource_size(mem),
+				pdev->dev.driver->name)) {
 		dev_err(&pdev->dev, "memory region already claimed\n");
 		return -EBUSY;
 	}
@@ -1308,7 +1308,7 @@ err:
 	dev_err(&pdev->dev, "[UART%d]: failure [%s]: %d\n",
 				pdev->id, __func__, ret);
 do_release_region:
-	release_mem_region(mem->start, (mem->end - mem->start) + 1);
+	release_mem_region(mem->start, resource_size(mem));
 	return ret;
 }
 
diff --git a/drivers/tty/serial/pch_uart.c b/drivers/tty/serial/pch_uart.c
index 46521093089..846dfcd3ce0 100644
--- a/drivers/tty/serial/pch_uart.c
+++ b/drivers/tty/serial/pch_uart.c
@@ -14,6 +14,7 @@
  *along with this program; if not, write to the Free Software
  *Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307, USA.
  */
+#include <linux/kernel.h>
 #include <linux/serial_reg.h>
 #include <linux/slab.h>
 #include <linux/module.h>
@@ -44,6 +45,7 @@ enum {
 /* Set the max number of UART port
  * Intel EG20T PCH: 4 port
  * OKI SEMICONDUCTOR ML7213 IOH: 3 port
+ * OKI SEMICONDUCTOR ML7223 IOH: 2 port
 */
 #define PCH_UART_NR	4
 
@@ -137,8 +139,6 @@ enum {
 #define PCH_UART_DLL		0x00
 #define PCH_UART_DLM		0x01
 
-#define DIV_ROUND(a, b)	(((a) + ((b)/2)) / (b))
-
 #define PCH_UART_IID_RLS	(PCH_UART_IIR_REI)
 #define PCH_UART_IID_RDR	(PCH_UART_IIR_RRI)
 #define PCH_UART_IID_RDR_TO	(PCH_UART_IIR_RRI | PCH_UART_IIR_TOI)
@@ -316,7 +316,7 @@ static int pch_uart_hal_set_line(struct eg20t_port *priv, int baud,
 	unsigned int dll, dlm, lcr;
 	int div;
 
-	div = DIV_ROUND(priv->base_baud / 16, baud);
+	div = DIV_ROUND_CLOSEST(priv->base_baud / 16, baud);
 	if (div < 0 || USHRT_MAX <= div) {
 		dev_err(priv->port.dev, "Invalid Baud(div=0x%x)\n", div);
 		return -EINVAL;
@@ -1429,6 +1429,8 @@ static struct eg20t_port *pch_uart_init_port(struct pci_dev *pdev,
 		goto init_port_hal_free;
 	}
 
+	pci_enable_msi(pdev);
+
 	iobase = pci_resource_start(pdev, 0);
 	mapbase = pci_resource_start(pdev, 1);
 	priv->mapbase = mapbase;
@@ -1485,6 +1487,8 @@ static void pch_uart_pci_remove(struct pci_dev *pdev)
 	struct eg20t_port *priv;
 
 	priv = (struct eg20t_port *)pci_get_drvdata(pdev);
+
+	pci_disable_msi(pdev);
 	pch_uart_exit_port(priv);
 	pci_disable_device(pdev);
 	kfree(priv);
@@ -1568,6 +1572,7 @@ static int __devinit pch_uart_pci_probe(struct pci_dev *pdev,
 	return ret;
 
 probe_disable_device:
+	pci_disable_msi(pdev);
 	pci_disable_device(pdev);
 probe_error:
 	return ret;
diff --git a/drivers/tty/serial/pxa.c b/drivers/tty/serial/pxa.c
index 4302e6e3768..531931c1b25 100644
--- a/drivers/tty/serial/pxa.c
+++ b/drivers/tty/serial/pxa.c
@@ -803,7 +803,7 @@ static int serial_pxa_probe(struct platform_device *dev)
 		break;
 	}
 
-	sport->port.membase = ioremap(mmres->start, mmres->end - mmres->start + 1);
+	sport->port.membase = ioremap(mmres->start, resource_size(mmres));
 	if (!sport->port.membase) {
 		ret = -ENOMEM;
 		goto err_clk;
diff --git a/drivers/tty/serial/s3c2400.c b/drivers/tty/serial/s3c2400.c
deleted file mode 100644
index d13051b3df8..00000000000
--- a/drivers/tty/serial/s3c2400.c
+++ /dev/null
@@ -1,105 +0,0 @@
-/*
- * Driver for Samsung SoC onboard UARTs.
- *
- * Ben Dooks, Copyright (c) 2003-2005 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/io.h>
-#include <linux/platform_device.h>
-
-#include <asm/irq.h>
-
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-#include <mach/regs-gpio.h>
-
-#include "samsung.h"
-
-static int s3c2400_serial_getsource(struct uart_port *port,
-				    struct s3c24xx_uart_clksrc *clk)
-{
-	clk->divisor = 1;
-	clk->name = "pclk";
-
-	return 0;
-}
-
-static int s3c2400_serial_setsource(struct uart_port *port,
-				    struct s3c24xx_uart_clksrc *clk)
-{
-	return 0;
-}
-
-static int s3c2400_serial_resetport(struct uart_port *port,
-				    struct s3c2410_uartcfg *cfg)
-{
-	dbg("s3c2400_serial_resetport: port=%p (%08lx), cfg=%p\n",
-	    port, port->mapbase, cfg);
-
-	wr_regl(port, S3C2410_UCON,  cfg->ucon);
-	wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
-	/* reset both fifos */
-
-	wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
-	wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
-	return 0;
-}
-
-static struct s3c24xx_uart_info s3c2400_uart_inf = {
-	.name		= "Samsung S3C2400 UART",
-	.type		= PORT_S3C2400,
-	.fifosize	= 16,
-	.rx_fifomask	= S3C2410_UFSTAT_RXMASK,
-	.rx_fifoshift	= S3C2410_UFSTAT_RXSHIFT,
-	.rx_fifofull	= S3C2410_UFSTAT_RXFULL,
-	.tx_fifofull	= S3C2410_UFSTAT_TXFULL,
-	.tx_fifomask	= S3C2410_UFSTAT_TXMASK,
-	.tx_fifoshift	= S3C2410_UFSTAT_TXSHIFT,
-	.get_clksrc	= s3c2400_serial_getsource,
-	.set_clksrc	= s3c2400_serial_setsource,
-	.reset_port	= s3c2400_serial_resetport,
-};
-
-static int s3c2400_serial_probe(struct platform_device *dev)
-{
-	return s3c24xx_serial_probe(dev, &s3c2400_uart_inf);
-}
-
-static struct platform_driver s3c2400_serial_driver = {
-	.probe		= s3c2400_serial_probe,
-	.remove		= __devexit_p(s3c24xx_serial_remove),
-	.driver		= {
-		.name	= "s3c2400-uart",
-		.owner	= THIS_MODULE,
-	},
-};
-
-s3c24xx_console_init(&s3c2400_serial_driver, &s3c2400_uart_inf);
-
-static inline int s3c2400_serial_init(void)
-{
-	return s3c24xx_serial_init(&s3c2400_serial_driver, &s3c2400_uart_inf);
-}
-
-static inline void s3c2400_serial_exit(void)
-{
-	platform_driver_unregister(&s3c2400_serial_driver);
-}
-
-module_init(s3c2400_serial_init);
-module_exit(s3c2400_serial_exit);
-
-MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Ben Dooks <ben@simtec.co.uk>");
-MODULE_DESCRIPTION("Samsung S3C2400 SoC Serial port driver");
-MODULE_ALIAS("platform:s3c2400-uart");
diff --git a/drivers/tty/serial/s3c2410.c b/drivers/tty/serial/s3c2410.c
index bffe6ff9b15..b1d7e7c1849 100644
--- a/drivers/tty/serial/s3c2410.c
+++ b/drivers/tty/serial/s3c2410.c
@@ -96,8 +96,6 @@ static struct platform_driver s3c2410_serial_driver = {
 	},
 };
 
-s3c24xx_console_init(&s3c2410_serial_driver, &s3c2410_uart_inf);
-
 static int __init s3c2410_serial_init(void)
 {
 	return s3c24xx_serial_init(&s3c2410_serial_driver, &s3c2410_uart_inf);
diff --git a/drivers/tty/serial/s3c2412.c b/drivers/tty/serial/s3c2412.c
index 7e2b9504a68..2234bf9ced4 100644
--- a/drivers/tty/serial/s3c2412.c
+++ b/drivers/tty/serial/s3c2412.c
@@ -130,8 +130,6 @@ static struct platform_driver s3c2412_serial_driver = {
 	},
 };
 
-s3c24xx_console_init(&s3c2412_serial_driver, &s3c2412_uart_inf);
-
 static inline int s3c2412_serial_init(void)
 {
 	return s3c24xx_serial_init(&s3c2412_serial_driver, &s3c2412_uart_inf);
diff --git a/drivers/tty/serial/s3c2440.c b/drivers/tty/serial/s3c2440.c
index 9e10d415d5f..1d0c324b813 100644
--- a/drivers/tty/serial/s3c2440.c
+++ b/drivers/tty/serial/s3c2440.c
@@ -159,8 +159,6 @@ static struct platform_driver s3c2440_serial_driver = {
 	},
 };
 
-s3c24xx_console_init(&s3c2440_serial_driver, &s3c2440_uart_inf);
-
 static int __init s3c2440_serial_init(void)
 {
 	return s3c24xx_serial_init(&s3c2440_serial_driver, &s3c2440_uart_inf);
diff --git a/drivers/tty/serial/s3c24a0.c b/drivers/tty/serial/s3c24a0.c
deleted file mode 100644
index 914eff22e49..00000000000
--- a/drivers/tty/serial/s3c24a0.c
+++ /dev/null
@@ -1,117 +0,0 @@
-/*
- * Driver for Samsung S3C24A0 SoC onboard UARTs.
- *
- * Based on drivers/serial/s3c2410.c
- *
- * Author: Sandeep Patil <sandeep.patil@azingo.com>
- *
- * Ben Dooks, Copyright (c) 2003-2008 Simtec Electronics
- *	http://armlinux.simtec.co.uk/
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
-*/
-
-#include <linux/module.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/init.h>
-#include <linux/serial_core.h>
-#include <linux/serial.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-
-#include <mach/hardware.h>
-
-#include <plat/regs-serial.h>
-#include <mach/regs-gpio.h>
-
-#include "samsung.h"
-
-static int s3c24a0_serial_setsource(struct uart_port *port,
-				    struct s3c24xx_uart_clksrc *clk)
-{
-	unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
-	if (strcmp(clk->name, "uclk") == 0)
-		ucon |= S3C2410_UCON_UCLK;
-	else
-		ucon &= ~S3C2410_UCON_UCLK;
-
-	wr_regl(port, S3C2410_UCON, ucon);
-	return 0;
-}
-
-static int s3c24a0_serial_getsource(struct uart_port *port,
-				    struct s3c24xx_uart_clksrc *clk)
-{
-	unsigned long ucon = rd_regl(port, S3C2410_UCON);
-
-	clk->divisor = 1;
-	clk->name = (ucon & S3C2410_UCON_UCLK) ? "uclk" : "pclk";
-
-	return 0;
-}
-
-static int s3c24a0_serial_resetport(struct uart_port *port,
-				    struct s3c2410_uartcfg *cfg)
-{
-	dbg("s3c24a0_serial_resetport: port=%p (%08lx), cfg=%p\n",
-	    port, port->mapbase, cfg);
-
-	wr_regl(port, S3C2410_UCON,  cfg->ucon);
-	wr_regl(port, S3C2410_ULCON, cfg->ulcon);
-
-	/* reset both fifos */
-
-	wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
-	wr_regl(port, S3C2410_UFCON, cfg->ufcon);
-
-	return 0;
-}
-
-static struct s3c24xx_uart_info s3c24a0_uart_inf = {
-	.name		= "Samsung S3C24A0 UART",
-	.type		= PORT_S3C2410,
-	.fifosize	= 16,
-	.rx_fifomask	= S3C24A0_UFSTAT_RXMASK,
-	.rx_fifoshift	= S3C24A0_UFSTAT_RXSHIFT,
-	.rx_fifofull	= S3C24A0_UFSTAT_RXFULL,
-	.tx_fifofull	= S3C24A0_UFSTAT_TXFULL,
-	.tx_fifomask	= S3C24A0_UFSTAT_TXMASK,
-	.tx_fifoshift	= S3C24A0_UFSTAT_TXSHIFT,
-	.get_clksrc	= s3c24a0_serial_getsource,
-	.set_clksrc	= s3c24a0_serial_setsource,
-	.reset_port	= s3c24a0_serial_resetport,
-};
-
-static int s3c24a0_serial_probe(struct platform_device *dev)
-{
-	return s3c24xx_serial_probe(dev, &s3c24a0_uart_inf);
-}
-
-static struct platform_driver s3c24a0_serial_driver = {
-	.probe		= s3c24a0_serial_probe,
-	.remove		= __devexit_p(s3c24xx_serial_remove),
-	.driver		= {
-		.name	= "s3c24a0-uart",
-		.owner	= THIS_MODULE,
-	},
-};
-
-s3c24xx_console_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf);
-
-static int __init s3c24a0_serial_init(void)
-{
-	return s3c24xx_serial_init(&s3c24a0_serial_driver, &s3c24a0_uart_inf);
-}
-
-static void __exit s3c24a0_serial_exit(void)
-{
-	platform_driver_unregister(&s3c24a0_serial_driver);
-}
-
-module_init(s3c24a0_serial_init);
-module_exit(s3c24a0_serial_exit);
-
diff --git a/drivers/tty/serial/s3c6400.c b/drivers/tty/serial/s3c6400.c
index ded26c42ff3..e2f6913d84d 100644
--- a/drivers/tty/serial/s3c6400.c
+++ b/drivers/tty/serial/s3c6400.c
@@ -130,8 +130,6 @@ static struct platform_driver s3c6400_serial_driver = {
 	},
 };
 
-s3c24xx_console_init(&s3c6400_serial_driver, &s3c6400_uart_inf);
-
 static int __init s3c6400_serial_init(void)
 {
 	return s3c24xx_serial_init(&s3c6400_serial_driver, &s3c6400_uart_inf);
diff --git a/drivers/tty/serial/s5pv210.c b/drivers/tty/serial/s5pv210.c
index dd194dc80ee..8b0b888a1b7 100644
--- a/drivers/tty/serial/s5pv210.c
+++ b/drivers/tty/serial/s5pv210.c
@@ -18,6 +18,7 @@
 #include <linux/init.h>
 #include <linux/serial_core.h>
 #include <linux/serial.h>
+#include <linux/delay.h>
 
 #include <asm/irq.h>
 #include <mach/hardware.h>
@@ -83,6 +84,9 @@ static int s5pv210_serial_resetport(struct uart_port *port,
 	wr_regl(port, S3C2410_UFCON, cfg->ufcon | S3C2410_UFCON_RESETBOTH);
 	wr_regl(port, S3C2410_UFCON, cfg->ufcon);
 
+	/* It is need to delay When reset FIFO register */
+	udelay(1);
+
 	return 0;
 }
 
@@ -135,13 +139,6 @@ static struct platform_driver s5p_serial_driver = {
 	},
 };
 
-static int __init s5pv210_serial_console_init(void)
-{
-	return s3c24xx_serial_initconsole(&s5p_serial_driver, s5p_uart_inf);
-}
-
-console_initcall(s5pv210_serial_console_init);
-
 static int __init s5p_serial_init(void)
 {
 	return s3c24xx_serial_init(&s5p_serial_driver, *s5p_uart_inf);
diff --git a/drivers/tty/serial/samsung.c b/drivers/tty/serial/samsung.c
index f66f6482930..afc62942315 100644
--- a/drivers/tty/serial/samsung.c
+++ b/drivers/tty/serial/samsung.c
@@ -1194,12 +1194,10 @@ int __devexit s3c24xx_serial_remove(struct platform_device *dev)
 EXPORT_SYMBOL_GPL(s3c24xx_serial_remove);
 
 /* UART power management code */
-
-#ifdef CONFIG_PM
-
-static int s3c24xx_serial_suspend(struct platform_device *dev, pm_message_t state)
+#ifdef CONFIG_PM_SLEEP
+static int s3c24xx_serial_suspend(struct device *dev)
 {
-	struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
+	struct uart_port *port = s3c24xx_dev_to_port(dev);
 
 	if (port)
 		uart_suspend_port(&s3c24xx_uart_drv, port);
@@ -1207,9 +1205,9 @@ static int s3c24xx_serial_suspend(struct platform_device *dev, pm_message_t stat
 	return 0;
 }
 
-static int s3c24xx_serial_resume(struct platform_device *dev)
+static int s3c24xx_serial_resume(struct device *dev)
 {
-	struct uart_port *port = s3c24xx_dev_to_port(&dev->dev);
+	struct uart_port *port = s3c24xx_dev_to_port(dev);
 	struct s3c24xx_uart_port *ourport = to_ourport(port);
 
 	if (port) {
@@ -1222,17 +1220,20 @@ static int s3c24xx_serial_resume(struct platform_device *dev)
 
 	return 0;
 }
-#endif
+
+static const struct dev_pm_ops s3c24xx_serial_pm_ops = {
+	.suspend = s3c24xx_serial_suspend,
+	.resume = s3c24xx_serial_resume,
+};
+#else /* !CONFIG_PM_SLEEP */
+#define s3c24xx_serial_pm_ops	NULL
+#endif /* CONFIG_PM_SLEEP */
 
 int s3c24xx_serial_init(struct platform_driver *drv,
 			struct s3c24xx_uart_info *info)
 {
 	dbg("s3c24xx_serial_init(%p,%p)\n", drv, info);
-
-#ifdef CONFIG_PM
-	drv->suspend = s3c24xx_serial_suspend;
-	drv->resume = s3c24xx_serial_resume;
-#endif
+	drv->driver.pm = &s3c24xx_serial_pm_ops;
 
 	return platform_driver_register(drv);
 }
@@ -1416,10 +1417,8 @@ s3c24xx_serial_console_setup(struct console *co, char *options)
 
 	/* is the port configured? */
 
-	if (port->mapbase == 0x0) {
-		co->index = 0;
-		port = &s3c24xx_serial_ports[co->index].port;
-	}
+	if (port->mapbase == 0x0)
+		return -ENODEV;
 
 	cons_uart = port;
 
@@ -1451,7 +1450,8 @@ static struct console s3c24xx_serial_console = {
 	.flags		= CON_PRINTBUFFER,
 	.index		= -1,
 	.write		= s3c24xx_serial_console_write,
-	.setup		= s3c24xx_serial_console_setup
+	.setup		= s3c24xx_serial_console_setup,
+	.data		= &s3c24xx_uart_drv,
 };
 
 int s3c24xx_serial_initconsole(struct platform_driver *drv,
diff --git a/drivers/tty/serial/samsung.h b/drivers/tty/serial/samsung.h
index 5b098cd7604..a69d9a54be9 100644
--- a/drivers/tty/serial/samsung.h
+++ b/drivers/tty/serial/samsung.h
@@ -79,25 +79,6 @@ extern int s3c24xx_serial_initconsole(struct platform_driver *drv,
 extern int s3c24xx_serial_init(struct platform_driver *drv,
 			       struct s3c24xx_uart_info *info);
 
-#ifdef CONFIG_SERIAL_SAMSUNG_CONSOLE
-
-#define s3c24xx_console_init(__drv, __inf)				\
-static int __init s3c_serial_console_init(void)				\
-{									\
-	struct s3c24xx_uart_info *uinfo[CONFIG_SERIAL_SAMSUNG_UARTS];	\
-	int i;								\
-									\
-	for (i = 0; i < CONFIG_SERIAL_SAMSUNG_UARTS; i++)		\
-		uinfo[i] = __inf;					\
-	return s3c24xx_serial_initconsole(__drv, uinfo);		\
-}									\
-									\
-console_initcall(s3c_serial_console_init)
-
-#else
-#define s3c24xx_console_init(drv, inf) extern void no_console(void)
-#endif
-
 #ifdef CONFIG_SERIAL_SAMSUNG_DEBUG
 
 extern void printascii(const char *);
diff --git a/drivers/tty/serial/sb1250-duart.c b/drivers/tty/serial/sb1250-duart.c
index ea2340b814e..6bc2e3f876f 100644
--- a/drivers/tty/serial/sb1250-duart.c
+++ b/drivers/tty/serial/sb1250-duart.c
@@ -39,7 +39,7 @@
 #include <linux/tty.h>
 #include <linux/types.h>
 
-#include <asm/atomic.h>
+#include <linux/atomic.h>
 #include <asm/io.h>
 #include <asm/war.h>
 
diff --git a/drivers/tty/serial/sunsu.c b/drivers/tty/serial/sunsu.c
index 92aa54550e8..ad0f8f5f6ea 100644
--- a/drivers/tty/serial/sunsu.c
+++ b/drivers/tty/serial/sunsu.c
@@ -1435,7 +1435,7 @@ static int __devinit su_probe(struct platform_device *op)
 
 	rp = &op->resource[0];
 	up->port.mapbase = rp->start;
-	up->reg_size = (rp->end - rp->start) + 1;
+	up->reg_size = resource_size(rp);
 	up->port.membase = of_ioremap(rp, 0, up->reg_size, "su");
 	if (!up->port.membase) {
 		if (type != SU_PORT_PORT)
diff --git a/drivers/tty/serial/vt8500_serial.c b/drivers/tty/serial/vt8500_serial.c
index 37fc4e3d487..026cb9ea5cd 100644
--- a/drivers/tty/serial/vt8500_serial.c
+++ b/drivers/tty/serial/vt8500_serial.c
@@ -573,8 +573,7 @@ static int __init vt8500_serial_probe(struct platform_device *pdev)
 	snprintf(vt8500_port->name, sizeof(vt8500_port->name),
 		 "VT8500 UART%d", pdev->id);
 
-	vt8500_port->uart.membase = ioremap(mmres->start,
-					    mmres->end - mmres->start + 1);
+	vt8500_port->uart.membase = ioremap(mmres->start, resource_size(mmres));
 	if (!vt8500_port->uart.membase) {
 		ret = -ENOMEM;
 		goto err;
diff --git a/drivers/tty/serial/zs.c b/drivers/tty/serial/zs.c
index 1a7fd3e7031..0aebd7121b5 100644
--- a/drivers/tty/serial/zs.c
+++ b/drivers/tty/serial/zs.c
@@ -65,7 +65,7 @@
 #include <linux/tty.h>
 #include <linux/types.h>
 
-#include <asm/atomic.h>
+#include <linux/atomic.h>
 #include <asm/system.h>
 
 #include <asm/dec/interrupts.h>