diff options
Diffstat (limited to 'drivers/tty')
-rw-r--r-- | drivers/tty/serial/omap-serial.c | 51 |
1 files changed, 1 insertions, 50 deletions
diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c index e00ac05cfdb..ca54f038ab4 100644 --- a/drivers/tty/serial/omap-serial.c +++ b/drivers/tty/serial/omap-serial.c @@ -88,49 +88,6 @@ static inline void serial_omap_clear_fifos(struct uart_omap_port *up) serial_out(up, UART_FCR, 0); } -/** - * serial_omap_block_cpu_low_power_state - prevent MPU pwrdm from leaving ON - * @up: struct uart_omap_port * - * - * Prevent the MPU powerdomain from entering a power state lower than - * ON. (It should be sufficient to prevent it from entering INACTIVE, - * but there is presently no easy way to do this.) This works around - * a suspected silicon bug in the OMAP UART IP blocks. The UARTs should - * wake the PRCM when the transmit FIFO threshold interrupt is raised, but - * they do not. See also serial_omap_allow_cpu_low_power_state(). No - * return value. - */ -static void serial_omap_block_cpu_low_power_state(struct uart_omap_port *up) -{ -#ifdef CONFIG_CPU_IDLE - up->latency = 1; - schedule_work(&up->qos_work); -#else - up->max_tx_count = 1; -#endif -} - -/** - * serial_omap_allow_cpu_low_power_state - remove power state restriction on MPU - * @up: struct uart_omap_port * - * - * Cancel the effects of serial_omap_block_cpu_low_power_state(). - * This should allow the MPU powerdomain to enter a power state lower - * than ON, assuming the rest of the kernel is not restricting it. - * This works around a suspected silicon bug in the OMAP UART IP - * blocks. The UARTs should wake the PRCM when the transmit FIFO - * threshold interrupt is raised, but they do not. No return value. - */ -static void serial_omap_allow_cpu_low_power_state(struct uart_omap_port *up) -{ -#ifdef CONFIG_CPU_IDLE - up->latency = up->calc_latency; - schedule_work(&up->qos_work); -#else - up->max_tx_count = up->port.fifosize / 4; -#endif -} - /* * serial_omap_get_divisor - calculate divisor value * @port: uart port info @@ -206,9 +163,6 @@ static void serial_omap_stop_tx(struct uart_port *port) serial_out(up, UART_IER, up->ier); } - if (!up->use_dma) - serial_omap_allow_cpu_low_power_state(up); - pm_runtime_mark_last_busy(&up->pdev->dev); pm_runtime_put_autosuspend(&up->pdev->dev); } @@ -310,7 +264,7 @@ static void transmit_chars(struct uart_omap_port *up) serial_omap_stop_tx(&up->port); return; } - count = up->max_tx_count; + count = up->port.fifosize / 4; do { serial_out(up, UART_TX, xmit->buf[xmit->tail]); xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); @@ -343,7 +297,6 @@ static void serial_omap_start_tx(struct uart_port *port) if (!up->use_dma) { pm_runtime_get_sync(&up->pdev->dev); - serial_omap_block_cpu_low_power_state(up); serial_omap_enable_ier_thri(up); pm_runtime_mark_last_busy(&up->pdev->dev); pm_runtime_put_autosuspend(&up->pdev->dev); @@ -1468,8 +1421,6 @@ static int serial_omap_probe(struct platform_device *pdev) up->port.fifosize = 64; up->port.ops = &serial_omap_pops; - up->max_tx_count = up->port.fifosize / 4; - if (pdev->dev.of_node) up->port.line = of_alias_get_id(pdev->dev.of_node, "serial"); else |