diff options
Diffstat (limited to 'drivers/tty')
| -rw-r--r-- | drivers/tty/serial/Kconfig | 10 | ||||
| -rw-r--r-- | drivers/tty/serial/ifx6x60.c | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/mxs-auart.c | 14 | ||||
| -rw-r--r-- | drivers/tty/serial/pmac_zilog.c | 12 |
4 files changed, 24 insertions, 14 deletions
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 070b442c1f8..4720b4ba096 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -160,10 +160,12 @@ config SERIAL_KS8695_CONSOLE config SERIAL_CLPS711X tristate "CLPS711X serial port support" - depends on ARM && ARCH_CLPS711X + depends on ARCH_CLPS711X select SERIAL_CORE + default y help - ::: To be written ::: + This enables the driver for the on-chip UARTs of the Cirrus + Logic EP711x/EP721x/EP731x processors. config SERIAL_CLPS711X_CONSOLE bool "Support for console on CLPS711X serial port" @@ -173,9 +175,7 @@ config SERIAL_CLPS711X_CONSOLE Even if you say Y here, the currently visible virtual console (/dev/tty0) will still be used as the system console by default, but you can alter that using a kernel command line option such as - "console=ttyCL1". (Try "man bootparam" or see the documentation of - your boot loader (lilo or loadlin) about how to pass options to the - kernel at boot time.) + "console=ttyCL1". config SERIAL_SAMSUNG tristate "Samsung SoC serial support" diff --git a/drivers/tty/serial/ifx6x60.c b/drivers/tty/serial/ifx6x60.c index 144cd3987d4..3ad079ffd04 100644 --- a/drivers/tty/serial/ifx6x60.c +++ b/drivers/tty/serial/ifx6x60.c @@ -1331,7 +1331,7 @@ static const struct spi_device_id ifx_id_table[] = { MODULE_DEVICE_TABLE(spi, ifx_id_table); /* spi operations */ -static const struct spi_driver ifx_spi_driver = { +static struct spi_driver ifx_spi_driver = { .driver = { .name = DRVNAME, .pm = &ifx_spi_pm, diff --git a/drivers/tty/serial/mxs-auart.c b/drivers/tty/serial/mxs-auart.c index 2e341b81ff8..3a667eed63d 100644 --- a/drivers/tty/serial/mxs-auart.c +++ b/drivers/tty/serial/mxs-auart.c @@ -73,6 +73,7 @@ #define AUART_CTRL0_CLKGATE (1 << 30) #define AUART_CTRL2_CTSEN (1 << 15) +#define AUART_CTRL2_RTSEN (1 << 14) #define AUART_CTRL2_RTS (1 << 11) #define AUART_CTRL2_RXE (1 << 9) #define AUART_CTRL2_TXE (1 << 8) @@ -259,9 +260,12 @@ static void mxs_auart_set_mctrl(struct uart_port *u, unsigned mctrl) u32 ctrl = readl(u->membase + AUART_CTRL2); - ctrl &= ~AUART_CTRL2_RTS; - if (mctrl & TIOCM_RTS) - ctrl |= AUART_CTRL2_RTS; + ctrl &= ~AUART_CTRL2_RTSEN; + if (mctrl & TIOCM_RTS) { + if (u->state->port.flags & ASYNC_CTS_FLOW) + ctrl |= AUART_CTRL2_RTSEN; + } + s->ctrl = mctrl; writel(ctrl, u->membase + AUART_CTRL2); } @@ -359,9 +363,9 @@ static void mxs_auart_settermios(struct uart_port *u, /* figure out the hardware flow control settings */ if (cflag & CRTSCTS) - ctrl2 |= AUART_CTRL2_CTSEN; + ctrl2 |= AUART_CTRL2_CTSEN | AUART_CTRL2_RTSEN; else - ctrl2 &= ~AUART_CTRL2_CTSEN; + ctrl2 &= ~(AUART_CTRL2_CTSEN | AUART_CTRL2_RTSEN); /* set baud rate */ baud = uart_get_baud_rate(u, termios, old, 0, u->uartclk); diff --git a/drivers/tty/serial/pmac_zilog.c b/drivers/tty/serial/pmac_zilog.c index 654755a990d..333c8d012b0 100644 --- a/drivers/tty/serial/pmac_zilog.c +++ b/drivers/tty/serial/pmac_zilog.c @@ -1348,10 +1348,16 @@ static int pmz_verify_port(struct uart_port *port, struct serial_struct *ser) static int pmz_poll_get_char(struct uart_port *port) { struct uart_pmac_port *uap = (struct uart_pmac_port *)port; + int tries = 2; - while ((read_zsreg(uap, R0) & Rx_CH_AV) == 0) - udelay(5); - return read_zsdata(uap); + while (tries) { + if ((read_zsreg(uap, R0) & Rx_CH_AV) != 0) + return read_zsdata(uap); + if (tries--) + udelay(5); + } + + return NO_POLL_CHAR; } static void pmz_poll_put_char(struct uart_port *port, unsigned char c) |