diff options
Diffstat (limited to 'drivers/tty')
| -rw-r--r-- | drivers/tty/serial/Kconfig | 1 | ||||
| -rw-r--r-- | drivers/tty/serial/atmel_serial.c | 105 |
2 files changed, 71 insertions, 35 deletions
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 4bf6d220357..fb57159bad3 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -117,6 +117,7 @@ config SERIAL_ATMEL bool "AT91 / AT32 on-chip serial port support" depends on ARCH_AT91 || AVR32 select SERIAL_CORE + select SERIAL_MCTRL_GPIO help This enables the driver for the on-chip UARTs of the Atmel AT91 and AT32 processors. diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 53eeea13ff1..43ca659c1d4 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -43,6 +43,8 @@ #include <linux/platform_data/atmel.h> #include <linux/timer.h> #include <linux/gpio.h> +#include <linux/gpio/consumer.h> +#include <linux/err.h> #include <asm/io.h> #include <asm/ioctls.h> @@ -57,6 +59,8 @@ #include <linux/serial_core.h> +#include "serial_mctrl_gpio.h" + static void atmel_start_rx(struct uart_port *port); static void atmel_stop_rx(struct uart_port *port); @@ -162,7 +166,7 @@ struct atmel_uart_port { struct circ_buf rx_ring; struct serial_rs485 rs485; /* rs485 settings */ - int rts_gpio; /* optional RTS GPIO */ + struct mctrl_gpios *gpios; unsigned int tx_done_mask; bool is_usart; /* usart or uart */ struct timer_list uart_timer; /* uart timer */ @@ -237,6 +241,50 @@ static bool atmel_use_dma_rx(struct uart_port *port) return atmel_port->use_dma_rx; } +static unsigned int atmel_get_lines_status(struct uart_port *port) +{ + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int status, ret = 0; + + status = UART_GET_CSR(port); + + mctrl_gpio_get(atmel_port->gpios, &ret); + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_CTS))) { + if (ret & TIOCM_CTS) + status &= ~ATMEL_US_CTS; + else + status |= ATMEL_US_CTS; + } + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_DSR))) { + if (ret & TIOCM_DSR) + status &= ~ATMEL_US_DSR; + else + status |= ATMEL_US_DSR; + } + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_RI))) { + if (ret & TIOCM_RI) + status &= ~ATMEL_US_RI; + else + status |= ATMEL_US_RI; + } + + if (!IS_ERR_OR_NULL(mctrl_gpio_to_gpiod(atmel_port->gpios, + UART_GPIO_DCD))) { + if (ret & TIOCM_CD) + status &= ~ATMEL_US_DCD; + else + status |= ATMEL_US_DCD; + } + + return status; +} + /* Enable or disable the rs485 support */ void atmel_config_rs485(struct uart_port *port, struct serial_rs485 *rs485conf) { @@ -296,17 +344,6 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) unsigned int mode; struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); - /* - * AT91RM9200 Errata #39: RTS0 is not internally connected - * to PA21. We need to drive the pin as a GPIO. - */ - if (gpio_is_valid(atmel_port->rts_gpio)) { - if (mctrl & TIOCM_RTS) - gpio_set_value(atmel_port->rts_gpio, 0); - else - gpio_set_value(atmel_port->rts_gpio, 1); - } - if (mctrl & TIOCM_RTS) control |= ATMEL_US_RTSEN; else @@ -319,6 +356,8 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) UART_PUT_CR(port, control); + mctrl_gpio_set(atmel_port->gpios, mctrl); + /* Local loopback mode? */ mode = UART_GET_MR(port) & ~ATMEL_US_CHMODE; if (mctrl & TIOCM_LOOP) @@ -346,7 +385,8 @@ static void atmel_set_mctrl(struct uart_port *port, u_int mctrl) */ static u_int atmel_get_mctrl(struct uart_port *port) { - unsigned int status, ret = 0; + struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned int ret = 0, status; status = UART_GET_CSR(port); @@ -362,7 +402,7 @@ static u_int atmel_get_mctrl(struct uart_port *port) if (!(status & ATMEL_US_RI)) ret |= TIOCM_RI; - return ret; + return mctrl_gpio_get(atmel_port->gpios, &ret); } /* @@ -1042,7 +1082,7 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) unsigned int status, pending, pass_counter = 0; do { - status = UART_GET_CSR(port); + status = atmel_get_lines_status(port); pending = status & UART_GET_IMR(port); if (!pending) break; @@ -1568,7 +1608,7 @@ static int atmel_startup(struct uart_port *port) } /* Save current CSR for comparison in atmel_tasklet_func() */ - atmel_port->irq_status_prev = UART_GET_CSR(port); + atmel_port->irq_status_prev = atmel_get_lines_status(port); atmel_port->irq_status = atmel_port->irq_status_prev; /* @@ -2324,6 +2364,15 @@ static int atmel_serial_resume(struct platform_device *pdev) #define atmel_serial_resume NULL #endif +static int atmel_init_gpios(struct atmel_uart_port *p, struct device *dev) +{ + p->gpios = mctrl_gpio_init(dev, 0); + if (IS_ERR_OR_NULL(p->gpios)) + return -1; + + return 0; +} + static int atmel_serial_probe(struct platform_device *pdev) { struct atmel_uart_port *port; @@ -2359,25 +2408,11 @@ static int atmel_serial_probe(struct platform_device *pdev) port = &atmel_ports[ret]; port->backup_imr = 0; port->uart.line = ret; - port->rts_gpio = -EINVAL; /* Invalid, zero could be valid */ - if (pdata) - port->rts_gpio = pdata->rts_gpio; - else if (np) - port->rts_gpio = of_get_named_gpio(np, "rts-gpios", 0); - - if (gpio_is_valid(port->rts_gpio)) { - ret = devm_gpio_request(&pdev->dev, port->rts_gpio, "RTS"); - if (ret) { - dev_err(&pdev->dev, "error requesting RTS GPIO\n"); - goto err; - } - /* Default to 1 as RTS is active low */ - ret = gpio_direction_output(port->rts_gpio, 1); - if (ret) { - dev_err(&pdev->dev, "error setting up RTS GPIO\n"); - goto err; - } - } + + ret = atmel_init_gpios(port, &pdev->dev); + if (ret < 0) + dev_err(&pdev->dev, "%s", + "Failed to initialize GPIOs. The serial port may not work as expected"); ret = atmel_init_port(port, pdev); if (ret) |