diff options
Diffstat (limited to 'drivers/usb/dwc3')
| -rw-r--r-- | drivers/usb/dwc3/Kconfig | 8 | ||||
| -rw-r--r-- | drivers/usb/dwc3/core.c | 51 | ||||
| -rw-r--r-- | drivers/usb/dwc3/core.h | 13 | ||||
| -rw-r--r-- | drivers/usb/dwc3/dwc3-omap.c | 189 | ||||
| -rw-r--r-- | drivers/usb/dwc3/gadget.c | 15 | ||||
| -rw-r--r-- | drivers/usb/dwc3/host.c | 14 |
6 files changed, 174 insertions, 116 deletions
diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig index 8eb996e4f05..785510a0a0c 100644 --- a/drivers/usb/dwc3/Kconfig +++ b/drivers/usb/dwc3/Kconfig @@ -45,6 +45,7 @@ comment "Platform Glue Driver Support" config USB_DWC3_OMAP tristate "Texas Instruments OMAP5 and similar Platforms" depends on EXTCON && (ARCH_OMAP2PLUS || COMPILE_TEST) + depends on OF default USB_DWC3 help Some platforms from Texas Instruments like OMAP5, DRA7xxx and @@ -92,4 +93,11 @@ config USB_DWC3_VERBOSE help Say Y here to enable verbose debugging messages on DWC3 Driver. +config DWC3_HOST_USB3_LPM_ENABLE + bool "Enable USB3 LPM Capability" + depends on USB_DWC3_HOST=y || USB_DWC3_DUAL_ROLE=y + default n + help + Select this when you want to enable USB3 LPM with dwc3 xhci host. + endif diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c index eb69eb9f06c..b769c1faaf0 100644 --- a/drivers/usb/dwc3/core.c +++ b/drivers/usb/dwc3/core.c @@ -386,6 +386,13 @@ static int dwc3_core_init(struct dwc3 *dwc) } dwc->revision = reg; + /* Handle USB2.0-only core configuration */ + if (DWC3_GHWPARAMS3_SSPHY_IFC(dwc->hwparams.hwparams3) == + DWC3_GHWPARAMS3_SSPHY_IFC_DIS) { + if (dwc->maximum_speed == USB_SPEED_SUPER) + dwc->maximum_speed = USB_SPEED_HIGH; + } + /* issue device SoftReset too */ timeout = jiffies + msecs_to_jiffies(500); dwc3_writel(dwc->regs, DWC3_DCTL, DWC3_DCTL_CSFTRST); @@ -656,6 +663,31 @@ static int dwc3_probe(struct platform_device *pdev) return -ENODEV; } + dwc->xhci_resources[0].start = res->start; + dwc->xhci_resources[0].end = dwc->xhci_resources[0].start + + DWC3_XHCI_REGS_END; + dwc->xhci_resources[0].flags = res->flags; + dwc->xhci_resources[0].name = res->name; + + res->start += DWC3_GLOBALS_REGS_START; + + /* + * Request memory region but exclude xHCI regs, + * since it will be requested by the xhci-plat driver. + */ + regs = devm_ioremap_resource(dev, res); + if (IS_ERR(regs)) + return PTR_ERR(regs); + + dwc->regs = regs; + dwc->regs_size = resource_size(res); + /* + * restore res->start back to its original value so that, + * in case the probe is deferred, we don't end up getting error in + * request the memory region the next time probe is called. + */ + res->start -= DWC3_GLOBALS_REGS_START; + if (node) { dwc->maximum_speed = of_usb_get_maximum_speed(node); @@ -676,28 +708,9 @@ static int dwc3_probe(struct platform_device *pdev) if (ret) return ret; - dwc->xhci_resources[0].start = res->start; - dwc->xhci_resources[0].end = dwc->xhci_resources[0].start + - DWC3_XHCI_REGS_END; - dwc->xhci_resources[0].flags = res->flags; - dwc->xhci_resources[0].name = res->name; - - res->start += DWC3_GLOBALS_REGS_START; - - /* - * Request memory region but exclude xHCI regs, - * since it will be requested by the xhci-plat driver. - */ - regs = devm_ioremap_resource(dev, res); - if (IS_ERR(regs)) - return PTR_ERR(regs); - spin_lock_init(&dwc->lock); platform_set_drvdata(pdev, dwc); - dwc->regs = regs; - dwc->regs_size = resource_size(res); - dev->dma_mask = dev->parent->dma_mask; dev->dma_parms = dev->parent->dma_parms; dma_set_coherent_mask(dev, dev->parent->coherent_dma_mask); diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h index 57332e3768e..48fb264065d 100644 --- a/drivers/usb/dwc3/core.h +++ b/drivers/usb/dwc3/core.h @@ -191,6 +191,19 @@ #define DWC3_GHWPARAMS1_PWROPT(n) ((n) << 24) #define DWC3_GHWPARAMS1_PWROPT_MASK DWC3_GHWPARAMS1_PWROPT(3) +/* Global HWPARAMS3 Register */ +#define DWC3_GHWPARAMS3_SSPHY_IFC(n) ((n) & 3) +#define DWC3_GHWPARAMS3_SSPHY_IFC_DIS 0 +#define DWC3_GHWPARAMS3_SSPHY_IFC_ENA 1 +#define DWC3_GHWPARAMS3_HSPHY_IFC(n) (((n) & (3 << 2)) >> 2) +#define DWC3_GHWPARAMS3_HSPHY_IFC_DIS 0 +#define DWC3_GHWPARAMS3_HSPHY_IFC_UTMI 1 +#define DWC3_GHWPARAMS3_HSPHY_IFC_ULPI 2 +#define DWC3_GHWPARAMS3_HSPHY_IFC_UTMI_ULPI 3 +#define DWC3_GHWPARAMS3_FSPHY_IFC(n) (((n) & (3 << 4)) >> 4) +#define DWC3_GHWPARAMS3_FSPHY_IFC_DIS 0 +#define DWC3_GHWPARAMS3_FSPHY_IFC_ENA 1 + /* Global HWPARAMS4 Register */ #define DWC3_GHWPARAMS4_HIBER_SCRATCHBUFS(n) (((n) & (0x0f << 13)) >> 13) #define DWC3_MAX_HIBER_SCRATCHBUFS 15 diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c index 4af4c356765..ef4936ff626 100644 --- a/drivers/usb/dwc3/dwc3-omap.c +++ b/drivers/usb/dwc3/dwc3-omap.c @@ -77,10 +77,6 @@ #define USBOTGSS_DEV_EBC_EN 0x0110 #define USBOTGSS_DEBUG_OFFSET 0x0600 -/* REVISION REGISTER */ -#define USBOTGSS_REVISION_XMAJOR(reg) ((reg >> 8) & 0x7) -#define USBOTGSS_REVISION_XMAJOR1 1 -#define USBOTGSS_REVISION_XMAJOR2 2 /* SYSCONFIG REGISTER */ #define USBOTGSS_SYSCONFIG_DMADISABLE (1 << 16) @@ -129,7 +125,6 @@ struct dwc3_omap { u32 irq_eoi_offset; u32 debug_offset; u32 irq0_offset; - u32 revision; u32 dma_status:1; @@ -322,7 +317,7 @@ static int dwc3_omap_remove_core(struct device *dev, void *c) { struct platform_device *pdev = to_platform_device(dev); - platform_device_unregister(pdev); + of_device_unregister(pdev); return 0; } @@ -383,6 +378,87 @@ static int dwc3_omap_vbus_notifier(struct notifier_block *nb, return NOTIFY_DONE; } +static void dwc3_omap_map_offset(struct dwc3_omap *omap) +{ + struct device_node *node = omap->dev->of_node; + + /* + * Differentiate between OMAP5 and AM437x. + * + * For OMAP5(ES2.0) and AM437x wrapper revision is same, even + * though there are changes in wrapper register offsets. + * + * Using dt compatible to differentiate AM437x. + */ + if (of_device_is_compatible(node, "ti,am437x-dwc3")) { + omap->irq_eoi_offset = USBOTGSS_EOI_OFFSET; + omap->irq0_offset = USBOTGSS_IRQ0_OFFSET; + omap->irqmisc_offset = USBOTGSS_IRQMISC_OFFSET; + omap->utmi_otg_offset = USBOTGSS_UTMI_OTG_OFFSET; + omap->debug_offset = USBOTGSS_DEBUG_OFFSET; + } +} + +static void dwc3_omap_set_utmi_mode(struct dwc3_omap *omap) +{ + u32 reg; + struct device_node *node = omap->dev->of_node; + int utmi_mode = 0; + + reg = dwc3_omap_read_utmi_status(omap); + + of_property_read_u32(node, "utmi-mode", &utmi_mode); + + switch (utmi_mode) { + case DWC3_OMAP_UTMI_MODE_SW: + reg |= USBOTGSS_UTMI_OTG_STATUS_SW_MODE; + break; + case DWC3_OMAP_UTMI_MODE_HW: + reg &= ~USBOTGSS_UTMI_OTG_STATUS_SW_MODE; + break; + default: + dev_dbg(omap->dev, "UNKNOWN utmi mode %d\n", utmi_mode); + } + + dwc3_omap_write_utmi_status(omap, reg); +} + +static int dwc3_omap_extcon_register(struct dwc3_omap *omap) +{ + u32 ret; + struct device_node *node = omap->dev->of_node; + struct extcon_dev *edev; + + if (of_property_read_bool(node, "extcon")) { + edev = extcon_get_edev_by_phandle(omap->dev, 0); + if (IS_ERR(edev)) { + dev_vdbg(omap->dev, "couldn't get extcon device\n"); + return -EPROBE_DEFER; + } + + omap->vbus_nb.notifier_call = dwc3_omap_vbus_notifier; + ret = extcon_register_interest(&omap->extcon_vbus_dev, + edev->name, "USB", + &omap->vbus_nb); + if (ret < 0) + dev_vdbg(omap->dev, "failed to register notifier for USB\n"); + + omap->id_nb.notifier_call = dwc3_omap_id_notifier; + ret = extcon_register_interest(&omap->extcon_id_dev, + edev->name, "USB-HOST", + &omap->id_nb); + if (ret < 0) + dev_vdbg(omap->dev, "failed to register notifier for USB-HOST\n"); + + if (extcon_get_cable_state(edev, "USB") == true) + dwc3_omap_set_mailbox(omap, OMAP_DWC3_VBUS_VALID); + if (extcon_get_cable_state(edev, "USB-HOST") == true) + dwc3_omap_set_mailbox(omap, OMAP_DWC3_ID_GROUND); + } + + return 0; +} + static int dwc3_omap_probe(struct platform_device *pdev) { struct device_node *node = pdev->dev.of_node; @@ -390,15 +466,11 @@ static int dwc3_omap_probe(struct platform_device *pdev) struct dwc3_omap *omap; struct resource *res; struct device *dev = &pdev->dev; - struct extcon_dev *edev; struct regulator *vbus_reg = NULL; int ret; int irq; - int utmi_mode = 0; - int x_major; - u32 reg; void __iomem *base; @@ -448,58 +520,8 @@ static int dwc3_omap_probe(struct platform_device *pdev) goto err0; } - reg = dwc3_omap_readl(omap->base, USBOTGSS_REVISION); - omap->revision = reg; - x_major = USBOTGSS_REVISION_XMAJOR(reg); - - /* Differentiate between OMAP5 and AM437x */ - switch (x_major) { - case USBOTGSS_REVISION_XMAJOR1: - case USBOTGSS_REVISION_XMAJOR2: - omap->irq_eoi_offset = 0; - omap->irq0_offset = 0; - omap->irqmisc_offset = 0; - omap->utmi_otg_offset = 0; - omap->debug_offset = 0; - break; - default: - /* Default to the latest revision */ - omap->irq_eoi_offset = USBOTGSS_EOI_OFFSET; - omap->irq0_offset = USBOTGSS_IRQ0_OFFSET; - omap->irqmisc_offset = USBOTGSS_IRQMISC_OFFSET; - omap->utmi_otg_offset = USBOTGSS_UTMI_OTG_OFFSET; - omap->debug_offset = USBOTGSS_DEBUG_OFFSET; - break; - } - - /* For OMAP5(ES2.0) and AM437x x_major is 2 even though there are - * changes in wrapper registers, Using dt compatible for aegis - */ - - if (of_device_is_compatible(node, "ti,am437x-dwc3")) { - omap->irq_eoi_offset = USBOTGSS_EOI_OFFSET; - omap->irq0_offset = USBOTGSS_IRQ0_OFFSET; - omap->irqmisc_offset = USBOTGSS_IRQMISC_OFFSET; - omap->utmi_otg_offset = USBOTGSS_UTMI_OTG_OFFSET; - omap->debug_offset = USBOTGSS_DEBUG_OFFSET; - } - - reg = dwc3_omap_read_utmi_status(omap); - - of_property_read_u32(node, "utmi-mode", &utmi_mode); - - switch (utmi_mode) { - case DWC3_OMAP_UTMI_MODE_SW: - reg |= USBOTGSS_UTMI_OTG_STATUS_SW_MODE; - break; - case DWC3_OMAP_UTMI_MODE_HW: - reg &= ~USBOTGSS_UTMI_OTG_STATUS_SW_MODE; - break; - default: - dev_dbg(dev, "UNKNOWN utmi mode %d\n", utmi_mode); - } - - dwc3_omap_write_utmi_status(omap, reg); + dwc3_omap_map_offset(omap); + dwc3_omap_set_utmi_mode(omap); /* check the DMA Status */ reg = dwc3_omap_readl(omap->base, USBOTGSS_SYSCONFIG); @@ -515,31 +537,9 @@ static int dwc3_omap_probe(struct platform_device *pdev) dwc3_omap_enable_irqs(omap); - if (of_property_read_bool(node, "extcon")) { - edev = extcon_get_edev_by_phandle(dev, 0); - if (IS_ERR(edev)) { - dev_vdbg(dev, "couldn't get extcon device\n"); - ret = -EPROBE_DEFER; - goto err2; - } - - omap->vbus_nb.notifier_call = dwc3_omap_vbus_notifier; - ret = extcon_register_interest(&omap->extcon_vbus_dev, - edev->name, "USB", &omap->vbus_nb); - if (ret < 0) - dev_vdbg(dev, "failed to register notifier for USB\n"); - omap->id_nb.notifier_call = dwc3_omap_id_notifier; - ret = extcon_register_interest(&omap->extcon_id_dev, edev->name, - "USB-HOST", &omap->id_nb); - if (ret < 0) - dev_vdbg(dev, - "failed to register notifier for USB-HOST\n"); - - if (extcon_get_cable_state(edev, "USB") == true) - dwc3_omap_set_mailbox(omap, OMAP_DWC3_VBUS_VALID); - if (extcon_get_cable_state(edev, "USB-HOST") == true) - dwc3_omap_set_mailbox(omap, OMAP_DWC3_ID_GROUND); - } + ret = dwc3_omap_extcon_register(omap); + if (ret < 0) + goto err2; ret = of_platform_populate(node, NULL, NULL, dev); if (ret) { @@ -599,7 +599,7 @@ static int dwc3_omap_prepare(struct device *dev) { struct dwc3_omap *omap = dev_get_drvdata(dev); - dwc3_omap_disable_irqs(omap); + dwc3_omap_write_irqmisc_set(omap, 0x00); return 0; } @@ -607,8 +607,19 @@ static int dwc3_omap_prepare(struct device *dev) static void dwc3_omap_complete(struct device *dev) { struct dwc3_omap *omap = dev_get_drvdata(dev); + u32 reg; - dwc3_omap_enable_irqs(omap); + reg = (USBOTGSS_IRQMISC_OEVT | + USBOTGSS_IRQMISC_DRVVBUS_RISE | + USBOTGSS_IRQMISC_CHRGVBUS_RISE | + USBOTGSS_IRQMISC_DISCHRGVBUS_RISE | + USBOTGSS_IRQMISC_IDPULLUP_RISE | + USBOTGSS_IRQMISC_DRVVBUS_FALL | + USBOTGSS_IRQMISC_CHRGVBUS_FALL | + USBOTGSS_IRQMISC_DISCHRGVBUS_FALL | + USBOTGSS_IRQMISC_IDPULLUP_FALL); + + dwc3_omap_write_irqmisc_set(omap, reg); } static int dwc3_omap_suspend(struct device *dev) diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c index 9d64dd02c57..349cacc577d 100644 --- a/drivers/usb/dwc3/gadget.c +++ b/drivers/usb/dwc3/gadget.c @@ -828,10 +828,6 @@ static void dwc3_prepare_one_trb(struct dwc3_ep *dep, length, last ? " last" : "", chain ? " chain" : ""); - /* Skip the LINK-TRB on ISOC */ - if (((dep->free_slot & DWC3_TRB_MASK) == DWC3_TRB_NUM - 1) && - usb_endpoint_xfer_isoc(dep->endpoint.desc)) - dep->free_slot++; trb = &dep->trb_pool[dep->free_slot & DWC3_TRB_MASK]; @@ -843,6 +839,10 @@ static void dwc3_prepare_one_trb(struct dwc3_ep *dep, } dep->free_slot++; + /* Skip the LINK-TRB on ISOC */ + if (((dep->free_slot & DWC3_TRB_MASK) == DWC3_TRB_NUM - 1) && + usb_endpoint_xfer_isoc(dep->endpoint.desc)) + dep->free_slot++; trb->size = DWC3_TRB_SIZE_LENGTH(length); trb->bpl = lower_32_bits(dma); @@ -1971,8 +1971,7 @@ static int dwc3_cleanup_done_reqs(struct dwc3 *dwc, struct dwc3_ep *dep, } static void dwc3_endpoint_transfer_complete(struct dwc3 *dwc, - struct dwc3_ep *dep, const struct dwc3_event_depevt *event, - int start_new) + struct dwc3_ep *dep, const struct dwc3_event_depevt *event) { unsigned status = 0; int clean_busy; @@ -2039,7 +2038,7 @@ static void dwc3_endpoint_interrupt(struct dwc3 *dwc, return; } - dwc3_endpoint_transfer_complete(dwc, dep, event, 1); + dwc3_endpoint_transfer_complete(dwc, dep, event); break; case DWC3_DEPEVT_XFERINPROGRESS: if (!usb_endpoint_xfer_isoc(dep->endpoint.desc)) { @@ -2048,7 +2047,7 @@ static void dwc3_endpoint_interrupt(struct dwc3 *dwc, return; } - dwc3_endpoint_transfer_complete(dwc, dep, event, 0); + dwc3_endpoint_transfer_complete(dwc, dep, event); break; case DWC3_DEPEVT_XFERNOTREADY: if (usb_endpoint_xfer_isoc(dep->endpoint.desc)) { diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c index 32db328cc76..dcb8ca08459 100644 --- a/drivers/usb/dwc3/host.c +++ b/drivers/usb/dwc3/host.c @@ -16,12 +16,14 @@ */ #include <linux/platform_device.h> +#include <linux/usb/xhci_pdriver.h> #include "core.h" int dwc3_host_init(struct dwc3 *dwc) { struct platform_device *xhci; + struct usb_xhci_pdata pdata; int ret; xhci = platform_device_alloc("xhci-hcd", PLATFORM_DEVID_AUTO); @@ -46,6 +48,18 @@ int dwc3_host_init(struct dwc3 *dwc) goto err1; } + memset(&pdata, 0, sizeof(pdata)); + +#ifdef CONFIG_DWC3_HOST_USB3_LPM_ENABLE + pdata.usb3_lpm_capable = 1; +#endif + + ret = platform_device_add_data(xhci, &pdata, sizeof(pdata)); + if (ret) { + dev_err(dwc->dev, "couldn't add platform data to xHCI device\n"); + goto err1; + } + ret = platform_device_add(xhci); if (ret) { dev_err(dwc->dev, "failed to register xHCI device\n"); |