summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/ehci-omap.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb/host/ehci-omap.c')
-rw-r--r--drivers/usb/host/ehci-omap.c882
1 files changed, 84 insertions, 798 deletions
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index f784ceb862a..7e41a95c5ce 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -4,9 +4,10 @@
* Bus Glue for the EHCI controllers in OMAP3/4
* Tested on several OMAP3 boards, and OMAP4 Pandaboard
*
- * Copyright (C) 2007-2010 Texas Instruments, Inc.
+ * Copyright (C) 2007-2011 Texas Instruments, Inc.
* Author: Vikram Pandita <vikram.pandita@ti.com>
* Author: Anand Gadiyar <gadiyar@ti.com>
+ * Author: Keshava Munegowda <keshava_mgowda@ti.com>
*
* Copyright (C) 2009 Nokia Corporation
* Contact: Felipe Balbi <felipe.balbi@nokia.com>
@@ -27,116 +28,19 @@
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
- * TODO (last updated Nov 21, 2010):
+ * TODO (last updated Feb 27, 2010):
* - add kernel-doc
* - enable AUTOIDLE
* - add suspend/resume
- * - move workarounds to board-files
- * - factor out code common to OHCI
* - add HSIC and TLL support
* - convert to use hwmod and runtime PM
*/
#include <linux/platform_device.h>
-#include <linux/clk.h>
-#include <linux/gpio.h>
-#include <linux/regulator/consumer.h>
#include <linux/slab.h>
#include <linux/usb/ulpi.h>
#include <plat/usb.h>
-/*
- * OMAP USBHOST Register addresses: VIRTUAL ADDRESSES
- * Use ehci_omap_readl()/ehci_omap_writel() functions
- */
-
-/* TLL Register Set */
-#define OMAP_USBTLL_REVISION (0x00)
-#define OMAP_USBTLL_SYSCONFIG (0x10)
-#define OMAP_USBTLL_SYSCONFIG_CACTIVITY (1 << 8)
-#define OMAP_USBTLL_SYSCONFIG_SIDLEMODE (1 << 3)
-#define OMAP_USBTLL_SYSCONFIG_ENAWAKEUP (1 << 2)
-#define OMAP_USBTLL_SYSCONFIG_SOFTRESET (1 << 1)
-#define OMAP_USBTLL_SYSCONFIG_AUTOIDLE (1 << 0)
-
-#define OMAP_USBTLL_SYSSTATUS (0x14)
-#define OMAP_USBTLL_SYSSTATUS_RESETDONE (1 << 0)
-
-#define OMAP_USBTLL_IRQSTATUS (0x18)
-#define OMAP_USBTLL_IRQENABLE (0x1C)
-
-#define OMAP_TLL_SHARED_CONF (0x30)
-#define OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN (1 << 6)
-#define OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN (1 << 5)
-#define OMAP_TLL_SHARED_CONF_USB_DIVRATION (1 << 2)
-#define OMAP_TLL_SHARED_CONF_FCLK_REQ (1 << 1)
-#define OMAP_TLL_SHARED_CONF_FCLK_IS_ON (1 << 0)
-
-#define OMAP_TLL_CHANNEL_CONF(num) (0x040 + 0x004 * num)
-#define OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF (1 << 11)
-#define OMAP_TLL_CHANNEL_CONF_ULPI_ULPIAUTOIDLE (1 << 10)
-#define OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE (1 << 9)
-#define OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE (1 << 8)
-#define OMAP_TLL_CHANNEL_CONF_CHANEN (1 << 0)
-
-#define OMAP_TLL_ULPI_FUNCTION_CTRL(num) (0x804 + 0x100 * num)
-#define OMAP_TLL_ULPI_INTERFACE_CTRL(num) (0x807 + 0x100 * num)
-#define OMAP_TLL_ULPI_OTG_CTRL(num) (0x80A + 0x100 * num)
-#define OMAP_TLL_ULPI_INT_EN_RISE(num) (0x80D + 0x100 * num)
-#define OMAP_TLL_ULPI_INT_EN_FALL(num) (0x810 + 0x100 * num)
-#define OMAP_TLL_ULPI_INT_STATUS(num) (0x813 + 0x100 * num)
-#define OMAP_TLL_ULPI_INT_LATCH(num) (0x814 + 0x100 * num)
-#define OMAP_TLL_ULPI_DEBUG(num) (0x815 + 0x100 * num)
-#define OMAP_TLL_ULPI_SCRATCH_REGISTER(num) (0x816 + 0x100 * num)
-
-#define OMAP_TLL_CHANNEL_COUNT 3
-#define OMAP_TLL_CHANNEL_1_EN_MASK (1 << 0)
-#define OMAP_TLL_CHANNEL_2_EN_MASK (1 << 1)
-#define OMAP_TLL_CHANNEL_3_EN_MASK (1 << 2)
-
-/* UHH Register Set */
-#define OMAP_UHH_REVISION (0x00)
-#define OMAP_UHH_SYSCONFIG (0x10)
-#define OMAP_UHH_SYSCONFIG_MIDLEMODE (1 << 12)
-#define OMAP_UHH_SYSCONFIG_CACTIVITY (1 << 8)
-#define OMAP_UHH_SYSCONFIG_SIDLEMODE (1 << 3)
-#define OMAP_UHH_SYSCONFIG_ENAWAKEUP (1 << 2)
-#define OMAP_UHH_SYSCONFIG_SOFTRESET (1 << 1)
-#define OMAP_UHH_SYSCONFIG_AUTOIDLE (1 << 0)
-
-#define OMAP_UHH_SYSSTATUS (0x14)
-#define OMAP_UHH_HOSTCONFIG (0x40)
-#define OMAP_UHH_HOSTCONFIG_ULPI_BYPASS (1 << 0)
-#define OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS (1 << 0)
-#define OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS (1 << 11)
-#define OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS (1 << 12)
-#define OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN (1 << 2)
-#define OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN (1 << 3)
-#define OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN (1 << 4)
-#define OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN (1 << 5)
-#define OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS (1 << 8)
-#define OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS (1 << 9)
-#define OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS (1 << 10)
-
-/* OMAP4-specific defines */
-#define OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR (3 << 2)
-#define OMAP4_UHH_SYSCONFIG_NOIDLE (1 << 2)
-
-#define OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR (3 << 4)
-#define OMAP4_UHH_SYSCONFIG_NOSTDBY (1 << 4)
-#define OMAP4_UHH_SYSCONFIG_SOFTRESET (1 << 0)
-
-#define OMAP4_P1_MODE_CLEAR (3 << 16)
-#define OMAP4_P1_MODE_TLL (1 << 16)
-#define OMAP4_P1_MODE_HSIC (3 << 16)
-#define OMAP4_P2_MODE_CLEAR (3 << 18)
-#define OMAP4_P2_MODE_TLL (1 << 18)
-#define OMAP4_P2_MODE_HSIC (3 << 18)
-
-#define OMAP_REV2_TLL_CHANNEL_COUNT 2
-
-#define OMAP_UHH_DEBUG_CSR (0x44)
-
/* EHCI Register Set */
#define EHCI_INSNREG04 (0xA0)
#define EHCI_INSNREG04_DISABLE_UNSUSPEND (1 << 5)
@@ -148,137 +52,24 @@
#define EHCI_INSNREG05_ULPI_EXTREGADD_SHIFT 8
#define EHCI_INSNREG05_ULPI_WRDATA_SHIFT 0
-/* Values of UHH_REVISION - Note: these are not given in the TRM */
-#define OMAP_EHCI_REV1 0x00000010 /* OMAP3 */
-#define OMAP_EHCI_REV2 0x50700100 /* OMAP4 */
-
-#define is_omap_ehci_rev1(x) (x->omap_ehci_rev == OMAP_EHCI_REV1)
-#define is_omap_ehci_rev2(x) (x->omap_ehci_rev == OMAP_EHCI_REV2)
+/*-------------------------------------------------------------------------*/
-#define is_ehci_phy_mode(x) (x == EHCI_HCD_OMAP_MODE_PHY)
-#define is_ehci_tll_mode(x) (x == EHCI_HCD_OMAP_MODE_TLL)
-#define is_ehci_hsic_mode(x) (x == EHCI_HCD_OMAP_MODE_HSIC)
+static const struct hc_driver ehci_omap_hc_driver;
-/*-------------------------------------------------------------------------*/
-static inline void ehci_omap_writel(void __iomem *base, u32 reg, u32 val)
+static inline void ehci_write(void __iomem *base, u32 reg, u32 val)
{
__raw_writel(val, base + reg);
}
-static inline u32 ehci_omap_readl(void __iomem *base, u32 reg)
+static inline u32 ehci_read(void __iomem *base, u32 reg)
{
return __raw_readl(base + reg);
}
-static inline void ehci_omap_writeb(void __iomem *base, u8 reg, u8 val)
-{
- __raw_writeb(val, base + reg);
-}
-
-static inline u8 ehci_omap_readb(void __iomem *base, u8 reg)
-{
- return __raw_readb(base + reg);
-}
-
-/*-------------------------------------------------------------------------*/
-
-struct ehci_hcd_omap {
- struct ehci_hcd *ehci;
- struct device *dev;
-
- struct clk *usbhost_ick;
- struct clk *usbhost_hs_fck;
- struct clk *usbhost_fs_fck;
- struct clk *usbtll_fck;
- struct clk *usbtll_ick;
- struct clk *xclk60mhsp1_ck;
- struct clk *xclk60mhsp2_ck;
- struct clk *utmi_p1_fck;
- struct clk *utmi_p2_fck;
-
- /* FIXME the following two workarounds are
- * board specific not silicon-specific so these
- * should be moved to board-file instead.
- *
- * Maybe someone from TI will know better which
- * board is affected and needs the workarounds
- * to be applied
- */
-
- /* gpio for resetting phy */
- int reset_gpio_port[OMAP3_HS_USB_PORTS];
-
- /* phy reset workaround */
- int phy_reset;
-
- /* IP revision */
- u32 omap_ehci_rev;
-
- /* desired phy_mode: TLL, PHY */
- enum ehci_hcd_omap_mode port_mode[OMAP3_HS_USB_PORTS];
-
- void __iomem *uhh_base;
- void __iomem *tll_base;
- void __iomem *ehci_base;
-
- /* Regulators for USB PHYs.
- * Each PHY can have a separate regulator.
- */
- struct regulator *regulator[OMAP3_HS_USB_PORTS];
-};
-
-/*-------------------------------------------------------------------------*/
-
-static void omap_usb_utmi_init(struct ehci_hcd_omap *omap, u8 tll_channel_mask,
- u8 tll_channel_count)
-{
- unsigned reg;
- int i;
-
- /* Program the 3 TLL channels upfront */
- for (i = 0; i < tll_channel_count; i++) {
- reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
-
- /* Disable AutoIdle, BitStuffing and use SDR Mode */
- reg &= ~(OMAP_TLL_CHANNEL_CONF_UTMIAUTOIDLE
- | OMAP_TLL_CHANNEL_CONF_ULPINOBITSTUFF
- | OMAP_TLL_CHANNEL_CONF_ULPIDDRMODE);
- ehci_omap_writel(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i), reg);
- }
-
- /* Program Common TLL register */
- reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_SHARED_CONF);
- reg |= (OMAP_TLL_SHARED_CONF_FCLK_IS_ON
- | OMAP_TLL_SHARED_CONF_USB_DIVRATION
- | OMAP_TLL_SHARED_CONF_USB_180D_SDR_EN);
- reg &= ~OMAP_TLL_SHARED_CONF_USB_90D_DDR_EN;
-
- ehci_omap_writel(omap->tll_base, OMAP_TLL_SHARED_CONF, reg);
-
- /* Enable channels now */
- for (i = 0; i < tll_channel_count; i++) {
- reg = ehci_omap_readl(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i));
-
- /* Enable only the reg that is needed */
- if (!(tll_channel_mask & 1<<i))
- continue;
-
- reg |= OMAP_TLL_CHANNEL_CONF_CHANEN;
- ehci_omap_writel(omap->tll_base, OMAP_TLL_CHANNEL_CONF(i), reg);
-
- ehci_omap_writeb(omap->tll_base,
- OMAP_TLL_ULPI_SCRATCH_REGISTER(i), 0xbe);
- dev_dbg(omap->dev, "ULPI_SCRATCH_REG[ch=%d]= 0x%02x\n",
- i+1, ehci_omap_readb(omap->tll_base,
- OMAP_TLL_ULPI_SCRATCH_REGISTER(i)));
- }
-}
-
-/*-------------------------------------------------------------------------*/
-
-static void omap_ehci_soft_phy_reset(struct ehci_hcd_omap *omap, u8 port)
+static void omap_ehci_soft_phy_reset(struct platform_device *pdev, u8 port)
{
+ struct usb_hcd *hcd = dev_get_drvdata(&pdev->dev);
unsigned long timeout = jiffies + msecs_to_jiffies(1000);
unsigned reg = 0;
@@ -292,266 +83,87 @@ static void omap_ehci_soft_phy_reset(struct ehci_hcd_omap *omap, u8 port)
/* start ULPI access*/
| (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT);
- ehci_omap_writel(omap->ehci_base, EHCI_INSNREG05_ULPI, reg);
+ ehci_write(hcd->regs, EHCI_INSNREG05_ULPI, reg);
/* Wait for ULPI access completion */
- while ((ehci_omap_readl(omap->ehci_base, EHCI_INSNREG05_ULPI)
+ while ((ehci_read(hcd->regs, EHCI_INSNREG05_ULPI)
& (1 << EHCI_INSNREG05_ULPI_CONTROL_SHIFT))) {
cpu_relax();
if (time_after(jiffies, timeout)) {
- dev_dbg(omap->dev, "phy reset operation timed out\n");
+ dev_dbg(&pdev->dev, "phy reset operation timed out\n");
break;
}
}
}
-/* omap_start_ehc
- * - Start the TI USBHOST controller
- */
-static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
-{
- unsigned long timeout = jiffies + msecs_to_jiffies(1000);
- u8 tll_ch_mask = 0;
- unsigned reg = 0;
- int ret = 0;
-
- dev_dbg(omap->dev, "starting TI EHCI USB Controller\n");
- /* Enable Clocks for USBHOST */
- omap->usbhost_ick = clk_get(omap->dev, "usbhost_ick");
- if (IS_ERR(omap->usbhost_ick)) {
- ret = PTR_ERR(omap->usbhost_ick);
- goto err_host_ick;
- }
- clk_enable(omap->usbhost_ick);
-
- omap->usbhost_hs_fck = clk_get(omap->dev, "hs_fck");
- if (IS_ERR(omap->usbhost_hs_fck)) {
- ret = PTR_ERR(omap->usbhost_hs_fck);
- goto err_host_120m_fck;
- }
- clk_enable(omap->usbhost_hs_fck);
+/* configure so an HC device and id are always provided */
+/* always called with process context; sleeping is OK */
- omap->usbhost_fs_fck = clk_get(omap->dev, "fs_fck");
- if (IS_ERR(omap->usbhost_fs_fck)) {
- ret = PTR_ERR(omap->usbhost_fs_fck);
- goto err_host_48m_fck;
- }
- clk_enable(omap->usbhost_fs_fck);
-
- if (omap->phy_reset) {
- /* Refer: ISSUE1 */
- if (gpio_is_valid(omap->reset_gpio_port[0])) {
- gpio_request(omap->reset_gpio_port[0],
- "USB1 PHY reset");
- gpio_direction_output(omap->reset_gpio_port[0], 0);
- }
+/**
+ * ehci_hcd_omap_probe - initialize TI-based HCDs
+ *
+ * Allocates basic resources for this USB host controller, and
+ * then invokes the start() method for the HCD associated with it
+ * through the hotplug entry's driver_data.
+ */
+static int ehci_hcd_omap_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct ehci_hcd_omap_platform_data *pdata = dev->platform_data;
+ struct resource *res;
+ struct usb_hcd *hcd;
+ void __iomem *regs;
+ struct ehci_hcd *omap_ehci;
+ int ret = -ENODEV;
+ int irq;
- if (gpio_is_valid(omap->reset_gpio_port[1])) {
- gpio_request(omap->reset_gpio_port[1],
- "USB2 PHY reset");
- gpio_direction_output(omap->reset_gpio_port[1], 0);
- }
+ if (usb_disabled())
+ return -ENODEV;
- /* Hold the PHY in RESET for enough time till DIR is high */
- udelay(10);
+ if (!dev->parent) {
+ dev_err(dev, "Missing parent device\n");
+ return -ENODEV;
}
- /* Configure TLL for 60Mhz clk for ULPI */
- omap->usbtll_fck = clk_get(omap->dev, "usbtll_fck");
- if (IS_ERR(omap->usbtll_fck)) {
- ret = PTR_ERR(omap->usbtll_fck);
- goto err_tll_fck;
+ irq = platform_get_irq_byname(pdev, "ehci-irq");
+ if (irq < 0) {
+ dev_err(dev, "EHCI irq failed\n");
+ return -ENODEV;
}
- clk_enable(omap->usbtll_fck);
- omap->usbtll_ick = clk_get(omap->dev, "usbtll_ick");
- if (IS_ERR(omap->usbtll_ick)) {
- ret = PTR_ERR(omap->usbtll_ick);
- goto err_tll_ick;
+ res = platform_get_resource_byname(pdev,
+ IORESOURCE_MEM, "ehci");
+ if (!res) {
+ dev_err(dev, "UHH EHCI get resource failed\n");
+ return -ENODEV;
}
- clk_enable(omap->usbtll_ick);
-
- omap->omap_ehci_rev = ehci_omap_readl(omap->uhh_base,
- OMAP_UHH_REVISION);
- dev_dbg(omap->dev, "OMAP UHH_REVISION 0x%x\n",
- omap->omap_ehci_rev);
- /*
- * Enable per-port clocks as needed (newer controllers only).
- * - External ULPI clock for PHY mode
- * - Internal clocks for TLL and HSIC modes (TODO)
- */
- if (is_omap_ehci_rev2(omap)) {
- switch (omap->port_mode[0]) {
- case EHCI_HCD_OMAP_MODE_PHY:
- omap->xclk60mhsp1_ck = clk_get(omap->dev,
- "xclk60mhsp1_ck");
- if (IS_ERR(omap->xclk60mhsp1_ck)) {
- ret = PTR_ERR(omap->xclk60mhsp1_ck);
- dev_err(omap->dev,
- "Unable to get Port1 ULPI clock\n");
- }
-
- omap->utmi_p1_fck = clk_get(omap->dev,
- "utmi_p1_gfclk");
- if (IS_ERR(omap->utmi_p1_fck)) {
- ret = PTR_ERR(omap->utmi_p1_fck);
- dev_err(omap->dev,
- "Unable to get utmi_p1_fck\n");
- }
-
- ret = clk_set_parent(omap->utmi_p1_fck,
- omap->xclk60mhsp1_ck);
- if (ret != 0) {
- dev_err(omap->dev,
- "Unable to set P1 f-clock\n");
- }
- break;
- case EHCI_HCD_OMAP_MODE_TLL:
- /* TODO */
- default:
- break;
- }
- switch (omap->port_mode[1]) {
- case EHCI_HCD_OMAP_MODE_PHY:
- omap->xclk60mhsp2_ck = clk_get(omap->dev,
- "xclk60mhsp2_ck");
- if (IS_ERR(omap->xclk60mhsp2_ck)) {
- ret = PTR_ERR(omap->xclk60mhsp2_ck);
- dev_err(omap->dev,
- "Unable to get Port2 ULPI clock\n");
- }
-
- omap->utmi_p2_fck = clk_get(omap->dev,
- "utmi_p2_gfclk");
- if (IS_ERR(omap->utmi_p2_fck)) {
- ret = PTR_ERR(omap->utmi_p2_fck);
- dev_err(omap->dev,
- "Unable to get utmi_p2_fck\n");
- }
-
- ret = clk_set_parent(omap->utmi_p2_fck,
- omap->xclk60mhsp2_ck);
- if (ret != 0) {
- dev_err(omap->dev,
- "Unable to set P2 f-clock\n");
- }
- break;
- case EHCI_HCD_OMAP_MODE_TLL:
- /* TODO */
- default:
- break;
- }
+ regs = ioremap(res->start, resource_size(res));
+ if (!regs) {
+ dev_err(dev, "UHH EHCI ioremap failed\n");
+ return -ENOMEM;
}
-
- /* perform TLL soft reset, and wait until reset is complete */
- ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
- OMAP_USBTLL_SYSCONFIG_SOFTRESET);
-
- /* Wait for TLL reset to complete */
- while (!(ehci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
- & OMAP_USBTLL_SYSSTATUS_RESETDONE)) {
- cpu_relax();
-
- if (time_after(jiffies, timeout)) {
- dev_dbg(omap->dev, "operation timed out\n");
- ret = -EINVAL;
- goto err_sys_status;
- }
+ hcd = usb_create_hcd(&ehci_omap_hc_driver, dev,
+ dev_name(dev));
+ if (!hcd) {
+ dev_err(dev, "failed to create hcd with err %d\n", ret);
+ ret = -ENOMEM;
+ goto err_io;
}
- dev_dbg(omap->dev, "TLL RESET DONE\n");
-
- /* (1<<3) = no idle mode only for initial debugging */
- ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG,
- OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
- OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
- OMAP_USBTLL_SYSCONFIG_CACTIVITY);
-
-
- /* Put UHH in NoIdle/NoStandby mode */
- reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSCONFIG);
- if (is_omap_ehci_rev1(omap)) {
- reg |= (OMAP_UHH_SYSCONFIG_ENAWAKEUP
- | OMAP_UHH_SYSCONFIG_SIDLEMODE
- | OMAP_UHH_SYSCONFIG_CACTIVITY
- | OMAP_UHH_SYSCONFIG_MIDLEMODE);
- reg &= ~OMAP_UHH_SYSCONFIG_AUTOIDLE;
-
+ hcd->rsrc_start = res->start;
+ hcd->rsrc_len = resource_size(res);
+ hcd->regs = regs;
- } else if (is_omap_ehci_rev2(omap)) {
- reg &= ~OMAP4_UHH_SYSCONFIG_IDLEMODE_CLEAR;
- reg |= OMAP4_UHH_SYSCONFIG_NOIDLE;
- reg &= ~OMAP4_UHH_SYSCONFIG_STDBYMODE_CLEAR;
- reg |= OMAP4_UHH_SYSCONFIG_NOSTDBY;
- }
- ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG, reg);
-
- reg = ehci_omap_readl(omap->uhh_base, OMAP_UHH_HOSTCONFIG);
-
- /* setup ULPI bypass and burst configurations */
- reg |= (OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
- | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN
- | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN);
- reg &= ~OMAP_UHH_HOSTCONFIG_INCRX_ALIGN_EN;
-
- if (is_omap_ehci_rev1(omap)) {
- if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_UNKNOWN)
- reg &= ~OMAP_UHH_HOSTCONFIG_P1_CONNECT_STATUS;
- if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_UNKNOWN)
- reg &= ~OMAP_UHH_HOSTCONFIG_P2_CONNECT_STATUS;
- if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_UNKNOWN)
- reg &= ~OMAP_UHH_HOSTCONFIG_P3_CONNECT_STATUS;
-
- /* Bypass the TLL module for PHY mode operation */
- if (cpu_is_omap3430() && (omap_rev() <= OMAP3430_REV_ES2_1)) {
- dev_dbg(omap->dev, "OMAP3 ES version <= ES2.1\n");
- if (is_ehci_phy_mode(omap->port_mode[0]) ||
- is_ehci_phy_mode(omap->port_mode[1]) ||
- is_ehci_phy_mode(omap->port_mode[2]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
- else
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_BYPASS;
- } else {
- dev_dbg(omap->dev, "OMAP3 ES version > ES2.1\n");
- if (is_ehci_phy_mode(omap->port_mode[0]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
- else if (is_ehci_tll_mode(omap->port_mode[0]))
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P1_BYPASS;
-
- if (is_ehci_phy_mode(omap->port_mode[1]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
- else if (is_ehci_tll_mode(omap->port_mode[1]))
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P2_BYPASS;
-
- if (is_ehci_phy_mode(omap->port_mode[2]))
- reg &= ~OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
- else if (is_ehci_tll_mode(omap->port_mode[2]))
- reg |= OMAP_UHH_HOSTCONFIG_ULPI_P3_BYPASS;
- }
- } else if (is_omap_ehci_rev2(omap)) {
- /* Clear port mode fields for PHY mode*/
- reg &= ~OMAP4_P1_MODE_CLEAR;
- reg &= ~OMAP4_P2_MODE_CLEAR;
-
- if (is_ehci_tll_mode(omap->port_mode[0]))
- reg |= OMAP4_P1_MODE_TLL;
- else if (is_ehci_hsic_mode(omap->port_mode[0]))
- reg |= OMAP4_P1_MODE_HSIC;
-
- if (is_ehci_tll_mode(omap->port_mode[1]))
- reg |= OMAP4_P2_MODE_TLL;
- else if (is_ehci_hsic_mode(omap->port_mode[1]))
- reg |= OMAP4_P2_MODE_HSIC;
+ ret = omap_usbhs_enable(dev);
+ if (ret) {
+ dev_err(dev, "failed to start usbhs with err %d\n", ret);
+ goto err_enable;
}
- ehci_omap_writel(omap->uhh_base, OMAP_UHH_HOSTCONFIG, reg);
- dev_dbg(omap->dev, "UHH setup done, uhh_hostconfig=%x\n", reg);
-
-
/*
* An undocumented "feature" in the OMAP3 EHCI controller,
* causes suspended ports to be taken out of suspend when
@@ -561,363 +173,50 @@ static int omap_start_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
* to suspend. Writing 1 to this undocumented register bit
* disables this feature and restores normal behavior.
*/
- ehci_omap_writel(omap->ehci_base, EHCI_INSNREG04,
+ ehci_write(regs, EHCI_INSNREG04,
EHCI_INSNREG04_DISABLE_UNSUSPEND);
- if ((omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL) ||
- (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL) ||
- (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)) {
-
- if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_TLL)
- tll_ch_mask |= OMAP_TLL_CHANNEL_1_EN_MASK;
- if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_TLL)
- tll_ch_mask |= OMAP_TLL_CHANNEL_2_EN_MASK;
- if (omap->port_mode[2] == EHCI_HCD_OMAP_MODE_TLL)
- tll_ch_mask |= OMAP_TLL_CHANNEL_3_EN_MASK;
-
- /* Enable UTMI mode for required TLL channels */
- omap_usb_utmi_init(omap, tll_ch_mask, OMAP_TLL_CHANNEL_COUNT);
- }
-
- if (omap->phy_reset) {
- /* Refer ISSUE1:
- * Hold the PHY in RESET for enough time till
- * PHY is settled and ready
- */
- udelay(10);
-
- if (gpio_is_valid(omap->reset_gpio_port[0]))
- gpio_set_value(omap->reset_gpio_port[0], 1);
-
- if (gpio_is_valid(omap->reset_gpio_port[1]))
- gpio_set_value(omap->reset_gpio_port[1], 1);
- }
-
/* Soft reset the PHY using PHY reset command over ULPI */
- if (omap->port_mode[0] == EHCI_HCD_OMAP_MODE_PHY)
- omap_ehci_soft_phy_reset(omap, 0);
- if (omap->port_mode[1] == EHCI_HCD_OMAP_MODE_PHY)
- omap_ehci_soft_phy_reset(omap, 1);
-
- return 0;
-
-err_sys_status:
- clk_disable(omap->utmi_p2_fck);
- clk_put(omap->utmi_p2_fck);
- clk_disable(omap->xclk60mhsp2_ck);
- clk_put(omap->xclk60mhsp2_ck);
- clk_disable(omap->utmi_p1_fck);
- clk_put(omap->utmi_p1_fck);
- clk_disable(omap->xclk60mhsp1_ck);
- clk_put(omap->xclk60mhsp1_ck);
- clk_disable(omap->usbtll_ick);
- clk_put(omap->usbtll_ick);
-
-err_tll_ick:
- clk_disable(omap->usbtll_fck);
- clk_put(omap->usbtll_fck);
-
-err_tll_fck:
- clk_disable(omap->usbhost_fs_fck);
- clk_put(omap->usbhost_fs_fck);
-
- if (omap->phy_reset) {
- if (gpio_is_valid(omap->reset_gpio_port[0]))
- gpio_free(omap->reset_gpio_port[0]);
-
- if (gpio_is_valid(omap->reset_gpio_port[1]))
- gpio_free(omap->reset_gpio_port[1]);
- }
-
-err_host_48m_fck:
- clk_disable(omap->usbhost_hs_fck);
- clk_put(omap->usbhost_hs_fck);
+ if (pdata->port_mode[0] == OMAP_EHCI_PORT_MODE_PHY)
+ omap_ehci_soft_phy_reset(pdev, 0);
+ if (pdata->port_mode[1] == OMAP_EHCI_PORT_MODE_PHY)
+ omap_ehci_soft_phy_reset(pdev, 1);
-err_host_120m_fck:
- clk_disable(omap->usbhost_ick);
- clk_put(omap->usbhost_ick);
-
-err_host_ick:
- return ret;
-}
-
-static void omap_stop_ehc(struct ehci_hcd_omap *omap, struct usb_hcd *hcd)
-{
- unsigned long timeout = jiffies + msecs_to_jiffies(100);
-
- dev_dbg(omap->dev, "stopping TI EHCI USB Controller\n");
-
- /* Reset OMAP modules for insmod/rmmod to work */
- ehci_omap_writel(omap->uhh_base, OMAP_UHH_SYSCONFIG,
- is_omap_ehci_rev2(omap) ?
- OMAP4_UHH_SYSCONFIG_SOFTRESET :
- OMAP_UHH_SYSCONFIG_SOFTRESET);
- while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
- & (1 << 0))) {
- cpu_relax();
-
- if (time_after(jiffies, timeout))
- dev_dbg(omap->dev, "operation timed out\n");
- }
-
- while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
- & (1 << 1))) {
- cpu_relax();
-
- if (time_after(jiffies, timeout))
- dev_dbg(omap->dev, "operation timed out\n");
- }
-
- while (!(ehci_omap_readl(omap->uhh_base, OMAP_UHH_SYSSTATUS)
- & (1 << 2))) {
- cpu_relax();
-
- if (time_after(jiffies, timeout))
- dev_dbg(omap->dev, "operation timed out\n");
- }
-
- ehci_omap_writel(omap->tll_base, OMAP_USBTLL_SYSCONFIG, (1 << 1));
-
- while (!(ehci_omap_readl(omap->tll_base, OMAP_USBTLL_SYSSTATUS)
- & (1 << 0))) {
- cpu_relax();
-
- if (time_after(jiffies, timeout))
- dev_dbg(omap->dev, "operation timed out\n");
- }
-
- if (omap->usbtll_fck != NULL) {
- clk_disable(omap->usbtll_fck);
- clk_put(omap->usbtll_fck);
- omap->usbtll_fck = NULL;
- }
-
- if (omap->usbhost_ick != NULL) {
- clk_disable(omap->usbhost_ick);
- clk_put(omap->usbhost_ick);
- omap->usbhost_ick = NULL;
- }
-
- if (omap->usbhost_fs_fck != NULL) {
- clk_disable(omap->usbhost_fs_fck);
- clk_put(omap->usbhost_fs_fck);
- omap->usbhost_fs_fck = NULL;
- }
-
- if (omap->usbhost_hs_fck != NULL) {
- clk_disable(omap->usbhost_hs_fck);
- clk_put(omap->usbhost_hs_fck);
- omap->usbhost_hs_fck = NULL;
- }
-
- if (omap->usbtll_ick != NULL) {
- clk_disable(omap->usbtll_ick);
- clk_put(omap->usbtll_ick);
- omap->usbtll_ick = NULL;
- }
-
- if (is_omap_ehci_rev2(omap)) {
- if (omap->xclk60mhsp1_ck != NULL) {
- clk_disable(omap->xclk60mhsp1_ck);
- clk_put(omap->xclk60mhsp1_ck);
- omap->xclk60mhsp1_ck = NULL;
- }
-
- if (omap->utmi_p1_fck != NULL) {
- clk_disable(omap->utmi_p1_fck);
- clk_put(omap->utmi_p1_fck);
- omap->utmi_p1_fck = NULL;
- }
-
- if (omap->xclk60mhsp2_ck != NULL) {
- clk_disable(omap->xclk60mhsp2_ck);
- clk_put(omap->xclk60mhsp2_ck);
- omap->xclk60mhsp2_ck = NULL;
- }
-
- if (omap->utmi_p2_fck != NULL) {
- clk_disable(omap->utmi_p2_fck);
- clk_put(omap->utmi_p2_fck);
- omap->utmi_p2_fck = NULL;
- }
- }
-
- if (omap->phy_reset) {
- if (gpio_is_valid(omap->reset_gpio_port[0]))
- gpio_free(omap->reset_gpio_port[0]);
-
- if (gpio_is_valid(omap->reset_gpio_port[1]))
- gpio_free(omap->reset_gpio_port[1]);
- }
-
- dev_dbg(omap->dev, "Clock to USB host has been disabled\n");
-}
-
-/*-------------------------------------------------------------------------*/
-
-static const struct hc_driver ehci_omap_hc_driver;
-
-/* configure so an HC device and id are always provided */
-/* always called with process context; sleeping is OK */
-
-/**
- * ehci_hcd_omap_probe - initialize TI-based HCDs
- *
- * Allocates basic resources for this USB host controller, and
- * then invokes the start() method for the HCD associated with it
- * through the hotplug entry's driver_data.
- */
-static int ehci_hcd_omap_probe(struct platform_device *pdev)
-{
- struct ehci_hcd_omap_platform_data *pdata = pdev->dev.platform_data;
- struct ehci_hcd_omap *omap;
- struct resource *res;
- struct usb_hcd *hcd;
-
- int irq = platform_get_irq(pdev, 0);
- int ret = -ENODEV;
- int i;
- char supply[7];
-
- if (!pdata) {
- dev_dbg(&pdev->dev, "missing platform_data\n");
- goto err_pdata;
- }
-
- if (usb_disabled())
- goto err_disabled;
-
- omap = kzalloc(sizeof(*omap), GFP_KERNEL);
- if (!omap) {
- ret = -ENOMEM;
- goto err_disabled;
- }
-
- hcd = usb_create_hcd(&ehci_omap_hc_driver, &pdev->dev,
- dev_name(&pdev->dev));
- if (!hcd) {
- dev_err(&pdev->dev, "failed to create hcd with err %d\n", ret);
- ret = -ENOMEM;
- goto err_create_hcd;
- }
-
- platform_set_drvdata(pdev, omap);
- omap->dev = &pdev->dev;
- omap->phy_reset = pdata->phy_reset;
- omap->reset_gpio_port[0] = pdata->reset_gpio_port[0];
- omap->reset_gpio_port[1] = pdata->reset_gpio_port[1];
- omap->reset_gpio_port[2] = pdata->reset_gpio_port[2];
- omap->port_mode[0] = pdata->port_mode[0];
- omap->port_mode[1] = pdata->port_mode[1];
- omap->port_mode[2] = pdata->port_mode[2];
- omap->ehci = hcd_to_ehci(hcd);
- omap->ehci->sbrn = 0x20;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-
- hcd->rsrc_start = res->start;
- hcd->rsrc_len = resource_size(res);
-
- hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
- if (!hcd->regs) {
- dev_err(&pdev->dev, "EHCI ioremap failed\n");
- ret = -ENOMEM;
- goto err_ioremap;
- }
+ omap_ehci = hcd_to_ehci(hcd);
+ omap_ehci->sbrn = 0x20;
/* we know this is the memory we want, no need to ioremap again */
- omap->ehci->caps = hcd->regs;
- omap->ehci_base = hcd->regs;
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
- omap->uhh_base = ioremap(res->start, resource_size(res));
- if (!omap->uhh_base) {
- dev_err(&pdev->dev, "UHH ioremap failed\n");
- ret = -ENOMEM;
- goto err_uhh_ioremap;
- }
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
- omap->tll_base = ioremap(res->start, resource_size(res));
- if (!omap->tll_base) {
- dev_err(&pdev->dev, "TLL ioremap failed\n");
- ret = -ENOMEM;
- goto err_tll_ioremap;
- }
-
- /* get ehci regulator and enable */
- for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
- if (omap->port_mode[i] != EHCI_HCD_OMAP_MODE_PHY) {
- omap->regulator[i] = NULL;
- continue;
- }
- snprintf(supply, sizeof(supply), "hsusb%d", i);
- omap->regulator[i] = regulator_get(omap->dev, supply);
- if (IS_ERR(omap->regulator[i])) {
- omap->regulator[i] = NULL;
- dev_dbg(&pdev->dev,
- "failed to get ehci port%d regulator\n", i);
- } else {
- regulator_enable(omap->regulator[i]);
- }
- }
-
- ret = omap_start_ehc(omap, hcd);
- if (ret) {
- dev_err(&pdev->dev, "failed to start ehci with err %d\n", ret);
- goto err_start;
- }
+ omap_ehci->caps = hcd->regs;
+ omap_ehci->regs = hcd->regs
+ + HC_LENGTH(readl(&omap_ehci->caps->hc_capbase));
- omap->ehci->regs = hcd->regs
- + HC_LENGTH(readl(&omap->ehci->caps->hc_capbase));
-
- dbg_hcs_params(omap->ehci, "reset");
- dbg_hcc_params(omap->ehci, "reset");
+ dbg_hcs_params(omap_ehci, "reset");
+ dbg_hcc_params(omap_ehci, "reset");
/* cache this readonly data; minimize chip reads */
- omap->ehci->hcs_params = readl(&omap->ehci->caps->hcs_params);
+ omap_ehci->hcs_params = readl(&omap_ehci->caps->hcs_params);
ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED);
if (ret) {
- dev_err(&pdev->dev, "failed to add hcd with err %d\n", ret);
+ dev_err(dev, "failed to add hcd with err %d\n", ret);
goto err_add_hcd;
}
/* root ports should always stay powered */
- ehci_port_power(omap->ehci, 1);
+ ehci_port_power(omap_ehci, 1);
return 0;
err_add_hcd:
- omap_stop_ehc(omap, hcd);
+ omap_usbhs_disable(dev);
-err_start:
- for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
- if (omap->regulator[i]) {
- regulator_disable(omap->regulator[i]);
- regulator_put(omap->regulator[i]);
- }
- }
- iounmap(omap->tll_base);
-
-err_tll_ioremap:
- iounmap(omap->uhh_base);
-
-err_uhh_ioremap:
- iounmap(hcd->regs);
-
-err_ioremap:
+err_enable:
usb_put_hcd(hcd);
-err_create_hcd:
- kfree(omap);
-err_disabled:
-err_pdata:
+err_io:
return ret;
}
-/* may be called without controller electrically present */
-/* may be called with controller, bus, and devices active */
/**
* ehci_hcd_omap_remove - shutdown processing for EHCI HCDs
@@ -929,31 +228,18 @@ err_pdata:
*/
static int ehci_hcd_omap_remove(struct platform_device *pdev)
{
- struct ehci_hcd_omap *omap = platform_get_drvdata(pdev);
- struct usb_hcd *hcd = ehci_to_hcd(omap->ehci);
- int i;
+ struct device *dev = &pdev->dev;
+ struct usb_hcd *hcd = dev_get_drvdata(dev);
usb_remove_hcd(hcd);
- omap_stop_ehc(omap, hcd);
- iounmap(hcd->regs);
- for (i = 0 ; i < OMAP3_HS_USB_PORTS ; i++) {
- if (omap->regulator[i]) {
- regulator_disable(omap->regulator[i]);
- regulator_put(omap->regulator[i]);
- }
- }
- iounmap(omap->tll_base);
- iounmap(omap->uhh_base);
+ omap_usbhs_disable(dev);
usb_put_hcd(hcd);
- kfree(omap);
-
return 0;
}
static void ehci_hcd_omap_shutdown(struct platform_device *pdev)
{
- struct ehci_hcd_omap *omap = platform_get_drvdata(pdev);
- struct usb_hcd *hcd = ehci_to_hcd(omap->ehci);
+ struct usb_hcd *hcd = dev_get_drvdata(&pdev->dev);
if (hcd->driver->shutdown)
hcd->driver->shutdown(hcd);