diff options
Diffstat (limited to 'drivers/usb/host/xhci-mem.c')
| -rw-r--r-- | drivers/usb/host/xhci-mem.c | 169 |
1 files changed, 169 insertions, 0 deletions
diff --git a/drivers/usb/host/xhci-mem.c b/drivers/usb/host/xhci-mem.c index d178761c398..1d0f45f0e7a 100644 --- a/drivers/usb/host/xhci-mem.c +++ b/drivers/usb/host/xhci-mem.c @@ -1443,6 +1443,13 @@ void xhci_mem_cleanup(struct xhci_hcd *xhci) xhci->dcbaa = NULL; scratchpad_free(xhci); + + xhci->num_usb2_ports = 0; + xhci->num_usb3_ports = 0; + kfree(xhci->usb2_ports); + kfree(xhci->usb3_ports); + kfree(xhci->port_array); + xhci->page_size = 0; xhci->page_shift = 0; xhci->bus_suspended = 0; @@ -1627,6 +1634,166 @@ static void xhci_set_hc_event_deq(struct xhci_hcd *xhci) &xhci->ir_set->erst_dequeue); } +static void xhci_add_in_port(struct xhci_hcd *xhci, unsigned int num_ports, + u32 __iomem *addr, u8 major_revision) +{ + u32 temp, port_offset, port_count; + int i; + + if (major_revision > 0x03) { + xhci_warn(xhci, "Ignoring unknown port speed, " + "Ext Cap %p, revision = 0x%x\n", + addr, major_revision); + /* Ignoring port protocol we can't understand. FIXME */ + return; + } + + /* Port offset and count in the third dword, see section 7.2 */ + temp = xhci_readl(xhci, addr + 2); + port_offset = XHCI_EXT_PORT_OFF(temp); + port_count = XHCI_EXT_PORT_COUNT(temp); + xhci_dbg(xhci, "Ext Cap %p, port offset = %u, " + "count = %u, revision = 0x%x\n", + addr, port_offset, port_count, major_revision); + /* Port count includes the current port offset */ + if (port_offset == 0 || (port_offset + port_count - 1) > num_ports) + /* WTF? "Valid values are ‘1’ to MaxPorts" */ + return; + port_offset--; + for (i = port_offset; i < (port_offset + port_count); i++) { + /* Duplicate entry. Ignore the port if the revisions differ. */ + if (xhci->port_array[i] != 0) { + xhci_warn(xhci, "Duplicate port entry, Ext Cap %p," + " port %u\n", addr, i); + xhci_warn(xhci, "Port was marked as USB %u, " + "duplicated as USB %u\n", + xhci->port_array[i], major_revision); + /* Only adjust the roothub port counts if we haven't + * found a similar duplicate. + */ + if (xhci->port_array[i] != major_revision && + xhci->port_array[i] != (u8) -1) { + if (xhci->port_array[i] == 0x03) + xhci->num_usb3_ports--; + else + xhci->num_usb2_ports--; + xhci->port_array[i] = (u8) -1; + } + /* FIXME: Should we disable the port? */ + continue; + } + xhci->port_array[i] = major_revision; + if (major_revision == 0x03) + xhci->num_usb3_ports++; + else + xhci->num_usb2_ports++; + } + /* FIXME: Should we disable ports not in the Extended Capabilities? */ +} + +/* + * Scan the Extended Capabilities for the "Supported Protocol Capabilities" that + * specify what speeds each port is supposed to be. We can't count on the port + * speed bits in the PORTSC register being correct until a device is connected, + * but we need to set up the two fake roothubs with the correct number of USB + * 3.0 and USB 2.0 ports at host controller initialization time. + */ +static int xhci_setup_port_arrays(struct xhci_hcd *xhci, gfp_t flags) +{ + u32 __iomem *addr; + u32 offset; + unsigned int num_ports; + int i, port_index; + + addr = &xhci->cap_regs->hcc_params; + offset = XHCI_HCC_EXT_CAPS(xhci_readl(xhci, addr)); + if (offset == 0) { + xhci_err(xhci, "No Extended Capability registers, " + "unable to set up roothub.\n"); + return -ENODEV; + } + + num_ports = HCS_MAX_PORTS(xhci->hcs_params1); + xhci->port_array = kzalloc(sizeof(*xhci->port_array)*num_ports, flags); + if (!xhci->port_array) + return -ENOMEM; + + /* + * For whatever reason, the first capability offset is from the + * capability register base, not from the HCCPARAMS register. + * See section 5.3.6 for offset calculation. + */ + addr = &xhci->cap_regs->hc_capbase + offset; + while (1) { + u32 cap_id; + + cap_id = xhci_readl(xhci, addr); + if (XHCI_EXT_CAPS_ID(cap_id) == XHCI_EXT_CAPS_PROTOCOL) + xhci_add_in_port(xhci, num_ports, addr, + (u8) XHCI_EXT_PORT_MAJOR(cap_id)); + offset = XHCI_EXT_CAPS_NEXT(cap_id); + if (!offset || (xhci->num_usb2_ports + xhci->num_usb3_ports) + == num_ports) + break; + /* + * Once you're into the Extended Capabilities, the offset is + * always relative to the register holding the offset. + */ + addr += offset; + } + + if (xhci->num_usb2_ports == 0 && xhci->num_usb3_ports == 0) { + xhci_warn(xhci, "No ports on the roothubs?\n"); + return -ENODEV; + } + xhci_dbg(xhci, "Found %u USB 2.0 ports and %u USB 3.0 ports.\n", + xhci->num_usb2_ports, xhci->num_usb3_ports); + /* + * Note we could have all USB 3.0 ports, or all USB 2.0 ports. + * Not sure how the USB core will handle a hub with no ports... + */ + if (xhci->num_usb2_ports) { + xhci->usb2_ports = kmalloc(sizeof(*xhci->usb2_ports)* + xhci->num_usb2_ports, flags); + if (!xhci->usb2_ports) + return -ENOMEM; + + port_index = 0; + for (i = 0; i < num_ports; i++) { + if (xhci->port_array[i] == 0x03 || + xhci->port_array[i] == 0 || + xhci->port_array[i] == -1) + continue; + + xhci->usb2_ports[port_index] = + &xhci->op_regs->port_status_base + + NUM_PORT_REGS*i; + xhci_dbg(xhci, "USB 2.0 port at index %u, " + "addr = %p\n", i, + xhci->usb2_ports[port_index]); + port_index++; + } + } + if (xhci->num_usb3_ports) { + xhci->usb3_ports = kmalloc(sizeof(*xhci->usb3_ports)* + xhci->num_usb3_ports, flags); + if (!xhci->usb3_ports) + return -ENOMEM; + + port_index = 0; + for (i = 0; i < num_ports; i++) + if (xhci->port_array[i] == 0x03) { + xhci->usb3_ports[port_index] = + &xhci->op_regs->port_status_base + + NUM_PORT_REGS*i; + xhci_dbg(xhci, "USB 3.0 port at index %u, " + "addr = %p\n", i, + xhci->usb3_ports[port_index]); + port_index++; + } + } + return 0; +} int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) { @@ -1809,6 +1976,8 @@ int xhci_mem_init(struct xhci_hcd *xhci, gfp_t flags) if (scratchpad_alloc(xhci, flags)) goto fail; + if (xhci_setup_port_arrays(xhci, flags)) + goto fail; return 0; |