1 files changed, 23 insertions, 159 deletions

diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 6e0d886bcce..4265b48856f 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -3459,7 +3459,7 @@ int xhci_discover_or_reset_device(struct usb_hcd *hcd, struct usb_device *udev)
 	/* Wait for the Reset Device command to finish */
 	timeleft = wait_for_completion_interruptible_timeout(
 			reset_device_cmd->completion,
-			USB_CTRL_SET_TIMEOUT);
+			XHCI_CMD_DEFAULT_TIMEOUT);
 	if (timeleft <= 0) {
 		xhci_warn(xhci, "%s while waiting for reset device command\n",
 				timeleft == 0 ? "Timeout" : "Signal");
@@ -3583,11 +3583,6 @@ void xhci_free_dev(struct usb_hcd *hcd, struct usb_device *udev)
 		del_timer_sync(&virt_dev->eps[i].stop_cmd_timer);
 	}
 
-	if (udev->usb2_hw_lpm_enabled) {
-		xhci_set_usb2_hardware_lpm(hcd, udev, 0);
-		udev->usb2_hw_lpm_enabled = 0;
-	}
-
 	spin_lock_irqsave(&xhci->lock, flags);
 	/* Don't disable the slot if the host controller is dead. */
 	state = xhci_readl(xhci, &xhci->op_regs->status);
@@ -3721,9 +3716,6 @@ disable_slot:
  * the device).
  * We should be protected by the usb_address0_mutex in khubd's hub_port_init, so
  * we should only issue and wait on one address command at the same time.
- *
- * We add one to the device address issued by the hardware because the USB core
- * uses address 1 for the root hubs (even though they're not really devices).
  */
 int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 {
@@ -3868,16 +3860,13 @@ int xhci_address_device(struct usb_hcd *hcd, struct usb_device *udev)
 	slot_ctx = xhci_get_slot_ctx(xhci, virt_dev->out_ctx);
 	trace_xhci_address_ctx(xhci, virt_dev->out_ctx,
 				slot_ctx->dev_info >> 27);
-	/* Use kernel assigned address for devices; store xHC assigned
-	 * address locally. */
-	virt_dev->address = (le32_to_cpu(slot_ctx->dev_state) & DEV_ADDR_MASK)
-		+ 1;
 	/* Zero the input context control for later use */
 	ctrl_ctx->add_flags = 0;
 	ctrl_ctx->drop_flags = 0;
 
 	xhci_dbg_trace(xhci, trace_xhci_dbg_address,
-			"Internal device address = %d", virt_dev->address);
+		       "Internal device address = %d",
+		       le32_to_cpu(slot_ctx->dev_state) & DEV_ADDR_MASK);
 
 	return 0;
 }
@@ -4025,133 +4014,6 @@ static int xhci_calculate_usb2_hw_lpm_params(struct usb_device *udev)
 	return PORT_BESLD(besld) | PORT_L1_TIMEOUT(l1) | PORT_HIRDM(hirdm);
 }
 
-static int xhci_usb2_software_lpm_test(struct usb_hcd *hcd,
-					struct usb_device *udev)
-{
-	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
-	struct dev_info	*dev_info;
-	__le32 __iomem	**port_array;
-	__le32 __iomem	*addr, *pm_addr;
-	u32		temp, dev_id;
-	unsigned int	port_num;
-	unsigned long	flags;
-	int		hird;
-	int		ret;
-
-	if (hcd->speed == HCD_USB3 || !xhci->sw_lpm_support ||
-			!udev->lpm_capable)
-		return -EINVAL;
-
-	/* we only support lpm for non-hub device connected to root hub yet */
-	if (!udev->parent || udev->parent->parent ||
-			udev->descriptor.bDeviceClass == USB_CLASS_HUB)
-		return -EINVAL;
-
-	spin_lock_irqsave(&xhci->lock, flags);
-
-	/* Look for devices in lpm_failed_devs list */
-	dev_id = le16_to_cpu(udev->descriptor.idVendor) << 16 |
-			le16_to_cpu(udev->descriptor.idProduct);
-	list_for_each_entry(dev_info, &xhci->lpm_failed_devs, list) {
-		if (dev_info->dev_id == dev_id) {
-			ret = -EINVAL;
-			goto finish;
-		}
-	}
-
-	port_array = xhci->usb2_ports;
-	port_num = udev->portnum - 1;
-
-	if (port_num > HCS_MAX_PORTS(xhci->hcs_params1)) {
-		xhci_dbg(xhci, "invalid port number %d\n", udev->portnum);
-		ret = -EINVAL;
-		goto finish;
-	}
-
-	/*
-	 * Test USB 2.0 software LPM.
-	 * FIXME: some xHCI 1.0 hosts may implement a new register to set up
-	 * hardware-controlled USB 2.0 LPM. See section 5.4.11 and 4.23.5.1.1.1
-	 * in the June 2011 errata release.
-	 */
-	xhci_dbg(xhci, "test port %d software LPM\n", port_num);
-	/*
-	 * Set L1 Device Slot and HIRD/BESL.
-	 * Check device's USB 2.0 extension descriptor to determine whether
-	 * HIRD or BESL shoule be used. See USB2.0 LPM errata.
-	 */
-	pm_addr = port_array[port_num] + PORTPMSC;
-	hird = xhci_calculate_hird_besl(xhci, udev);
-	temp = PORT_L1DS(udev->slot_id) | PORT_HIRD(hird);
-	xhci_writel(xhci, temp, pm_addr);
-
-	/* Set port link state to U2(L1) */
-	addr = port_array[port_num];
-	xhci_set_link_state(xhci, port_array, port_num, XDEV_U2);
-
-	/* wait for ACK */
-	spin_unlock_irqrestore(&xhci->lock, flags);
-	msleep(10);
-	spin_lock_irqsave(&xhci->lock, flags);
-
-	/* Check L1 Status */
-	ret = xhci_handshake(xhci, pm_addr,
-			PORT_L1S_MASK, PORT_L1S_SUCCESS, 125);
-	if (ret != -ETIMEDOUT) {
-		/* enter L1 successfully */
-		temp = xhci_readl(xhci, addr);
-		xhci_dbg(xhci, "port %d entered L1 state, port status 0x%x\n",
-				port_num, temp);
-		ret = 0;
-	} else {
-		temp = xhci_readl(xhci, pm_addr);
-		xhci_dbg(xhci, "port %d software lpm failed, L1 status %d\n",
-				port_num, temp & PORT_L1S_MASK);
-		ret = -EINVAL;
-	}
-
-	/* Resume the port */
-	xhci_set_link_state(xhci, port_array, port_num, XDEV_U0);
-
-	spin_unlock_irqrestore(&xhci->lock, flags);
-	msleep(10);
-	spin_lock_irqsave(&xhci->lock, flags);
-
-	/* Clear PLC */
-	xhci_test_and_clear_bit(xhci, port_array, port_num, PORT_PLC);
-
-	/* Check PORTSC to make sure the device is in the right state */
-	if (!ret) {
-		temp = xhci_readl(xhci, addr);
-		xhci_dbg(xhci, "resumed port %d status 0x%x\n",	port_num, temp);
-		if (!(temp & PORT_CONNECT) || !(temp & PORT_PE) ||
-				(temp & PORT_PLS_MASK) != XDEV_U0) {
-			xhci_dbg(xhci, "port L1 resume fail\n");
-			ret = -EINVAL;
-		}
-	}
-
-	if (ret) {
-		/* Insert dev to lpm_failed_devs list */
-		xhci_warn(xhci, "device LPM test failed, may disconnect and "
-				"re-enumerate\n");
-		dev_info = kzalloc(sizeof(struct dev_info), GFP_ATOMIC);
-		if (!dev_info) {
-			ret = -ENOMEM;
-			goto finish;
-		}
-		dev_info->dev_id = dev_id;
-		INIT_LIST_HEAD(&dev_info->list);
-		list_add(&dev_info->list, &xhci->lpm_failed_devs);
-	} else {
-		xhci_ring_device(xhci, udev->slot_id);
-	}
-
-finish:
-	spin_unlock_irqrestore(&xhci->lock, flags);
-	return ret;
-}
-
 int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
 			struct usb_device *udev, int enable)
 {
@@ -4228,7 +4090,7 @@ int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
 		}
 
 		pm_val &= ~PORT_HIRD_MASK;
-		pm_val |= PORT_HIRD(hird) | PORT_RWE;
+		pm_val |= PORT_HIRD(hird) | PORT_RWE | PORT_L1DS(udev->slot_id);
 		xhci_writel(xhci, pm_val, pm_addr);
 		pm_val = xhci_readl(xhci, pm_addr);
 		pm_val |= PORT_HLE;
@@ -4236,7 +4098,7 @@ int xhci_set_usb2_hardware_lpm(struct usb_hcd *hcd,
 		/* flush write */
 		xhci_readl(xhci, pm_addr);
 	} else {
-		pm_val &= ~(PORT_HLE | PORT_RWE | PORT_HIRD_MASK);
+		pm_val &= ~(PORT_HLE | PORT_RWE | PORT_HIRD_MASK | PORT_L1DS_MASK);
 		xhci_writel(xhci, pm_val, pm_addr);
 		/* flush write */
 		xhci_readl(xhci, pm_addr);
@@ -4279,24 +4141,26 @@ static int xhci_check_usb2_port_capability(struct xhci_hcd *xhci, int port,
 int xhci_update_device(struct usb_hcd *hcd, struct usb_device *udev)
 {
 	struct xhci_hcd	*xhci = hcd_to_xhci(hcd);
-	int		ret;
 	int		portnum = udev->portnum - 1;
 
-	ret = xhci_usb2_software_lpm_test(hcd, udev);
-	if (!ret) {
-		xhci_dbg(xhci, "software LPM test succeed\n");
-		if (xhci->hw_lpm_support == 1 &&
-		    xhci_check_usb2_port_capability(xhci, portnum, XHCI_HLC)) {
-			udev->usb2_hw_lpm_capable = 1;
-			udev->l1_params.timeout = XHCI_L1_TIMEOUT;
-			udev->l1_params.besl = XHCI_DEFAULT_BESL;
-			if (xhci_check_usb2_port_capability(xhci, portnum,
-							    XHCI_BLC))
-				udev->usb2_hw_lpm_besl_capable = 1;
-			ret = xhci_set_usb2_hardware_lpm(hcd, udev, 1);
-			if (!ret)
-				udev->usb2_hw_lpm_enabled = 1;
-		}
+	if (hcd->speed == HCD_USB3 || !xhci->sw_lpm_support ||
+			!udev->lpm_capable)
+		return 0;
+
+	/* we only support lpm for non-hub device connected to root hub yet */
+	if (!udev->parent || udev->parent->parent ||
+			udev->descriptor.bDeviceClass == USB_CLASS_HUB)
+		return 0;
+
+	if (xhci->hw_lpm_support == 1 &&
+			xhci_check_usb2_port_capability(
+				xhci, portnum, XHCI_HLC)) {
+		udev->usb2_hw_lpm_capable = 1;
+		udev->l1_params.timeout = XHCI_L1_TIMEOUT;
+		udev->l1_params.besl = XHCI_DEFAULT_BESL;
+		if (xhci_check_usb2_port_capability(xhci, portnum,
+					XHCI_BLC))
+			udev->usb2_hw_lpm_besl_capable = 1;
 	}
 
 	return 0;