diff options
Diffstat (limited to 'drivers/usb/host')
32 files changed, 596 insertions, 446 deletions
diff --git a/drivers/usb/host/ehci-au1xxx.c b/drivers/usb/host/ehci-au1xxx.c index 08a4335401a..bf69f473910 100644 --- a/drivers/usb/host/ehci-au1xxx.c +++ b/drivers/usb/host/ehci-au1xxx.c @@ -19,263 +19,304 @@ #define USB_MCFG_RDCOMB (1<<30) #define USB_MCFG_SSDEN (1<<23) #define USB_MCFG_PHYPLLEN (1<<19) +#define USB_MCFG_UCECLKEN (1<<18) #define USB_MCFG_EHCCLKEN (1<<17) +#ifdef CONFIG_DMA_COHERENT #define USB_MCFG_UCAM (1<<7) +#else +#define USB_MCFG_UCAM (0) +#endif #define USB_MCFG_EBMEN (1<<3) #define USB_MCFG_EMEMEN (1<<2) -#define USBH_ENABLE_CE (USB_MCFG_PHYPLLEN | USB_MCFG_EHCCLKEN) +#define USBH_ENABLE_CE (USB_MCFG_PHYPLLEN | USB_MCFG_EHCCLKEN) +#define USBH_ENABLE_INIT (USB_MCFG_PFEN | USB_MCFG_RDCOMB | \ + USBH_ENABLE_CE | USB_MCFG_SSDEN | \ + USB_MCFG_UCAM | USB_MCFG_EBMEN | \ + USB_MCFG_EMEMEN) -#ifdef CONFIG_DMA_COHERENT -#define USBH_ENABLE_INIT (USBH_ENABLE_CE \ - | USB_MCFG_PFEN | USB_MCFG_RDCOMB \ - | USB_MCFG_SSDEN | USB_MCFG_UCAM \ - | USB_MCFG_EBMEN | USB_MCFG_EMEMEN) -#else -#define USBH_ENABLE_INIT (USBH_ENABLE_CE \ - | USB_MCFG_PFEN | USB_MCFG_RDCOMB \ - | USB_MCFG_SSDEN \ - | USB_MCFG_EBMEN | USB_MCFG_EMEMEN) -#endif #define USBH_DISABLE (USB_MCFG_EBMEN | USB_MCFG_EMEMEN) extern int usb_disabled(void); -/*-------------------------------------------------------------------------*/ - -static void au1xxx_start_ehc(struct platform_device *dev) +static void au1xxx_start_ehc(void) { - pr_debug(__FILE__ ": starting Au1xxx EHCI USB Controller\n"); - - /* write HW defaults again in case Yamon cleared them */ - if (au_readl(USB_HOST_CONFIG) == 0) { - au_writel(0x00d02000, USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); - udelay(1000); - } - /* enable host controller */ - au_writel(USBH_ENABLE_CE | au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); - udelay(1000); - au_writel(USBH_ENABLE_INIT | au_readl(USB_HOST_CONFIG), - USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); + /* enable clock to EHCI block and HS PHY PLL*/ + au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_CE, USB_HOST_CONFIG); + au_sync(); udelay(1000); - pr_debug(__FILE__ ": Clock to USB host has been enabled\n"); + /* enable EHCI mmio */ + au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG); + au_sync(); + udelay(1000); } -static void au1xxx_stop_ehc(struct platform_device *dev) +static void au1xxx_stop_ehc(void) { - pr_debug(__FILE__ ": stopping Au1xxx EHCI USB Controller\n"); + unsigned long c; /* Disable mem */ - au_writel(~USBH_DISABLE & au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG); + au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_DISABLE, USB_HOST_CONFIG); + au_sync(); udelay(1000); - /* Disable clock */ - au_writel(~USB_MCFG_EHCCLKEN & au_readl(USB_HOST_CONFIG), - USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); + + /* Disable EHC clock. If the HS PHY is unused disable it too. */ + c = au_readl(USB_HOST_CONFIG) & ~USB_MCFG_EHCCLKEN; + if (!(c & USB_MCFG_UCECLKEN)) /* UDC disabled? */ + c &= ~USB_MCFG_PHYPLLEN; /* yes: disable HS PHY PLL */ + au_writel(c, USB_HOST_CONFIG); + au_sync(); } -/*-------------------------------------------------------------------------*/ +static const struct hc_driver ehci_au1xxx_hc_driver = { + .description = hcd_name, + .product_desc = "Au1xxx EHCI", + .hcd_priv_size = sizeof(struct ehci_hcd), + + /* + * generic hardware linkage + */ + .irq = ehci_irq, + .flags = HCD_MEMORY | HCD_USB2, + + /* + * basic lifecycle operations + * + * FIXME -- ehci_init() doesn't do enough here. + * See ehci-ppc-soc for a complete implementation. + */ + .reset = ehci_init, + .start = ehci_run, + .stop = ehci_stop, + .shutdown = ehci_shutdown, -/* configure so an HC device and id are always provided */ -/* always called with process context; sleeping is OK */ + /* + * managing i/o requests and associated device resources + */ + .urb_enqueue = ehci_urb_enqueue, + .urb_dequeue = ehci_urb_dequeue, + .endpoint_disable = ehci_endpoint_disable, -/** - * usb_ehci_au1xxx_probe - initialize Au1xxx-based HCDs - * Context: !in_interrupt() - * - * Allocates basic resources for this USB host controller, and - * then invokes the start() method for the HCD associated with it - * through the hotplug entry's driver_data. - * - */ -int usb_ehci_au1xxx_probe(const struct hc_driver *driver, - struct usb_hcd **hcd_out, struct platform_device *dev) + /* + * scheduling support + */ + .get_frame_number = ehci_get_frame, + + /* + * root hub support + */ + .hub_status_data = ehci_hub_status_data, + .hub_control = ehci_hub_control, + .bus_suspend = ehci_bus_suspend, + .bus_resume = ehci_bus_resume, + .relinquish_port = ehci_relinquish_port, + .port_handed_over = ehci_port_handed_over, +}; + +static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev) { - int retval; struct usb_hcd *hcd; struct ehci_hcd *ehci; + int ret; -#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT) + if (usb_disabled()) + return -ENODEV; +#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT) /* Au1200 AB USB does not support coherent memory */ if (!(read_c0_prid() & 0xff)) { - pr_info("%s: this is chip revision AB!\n", dev->name); - pr_info("%s: update your board or re-configure the kernel\n", - dev->name); + printk(KERN_INFO "%s: this is chip revision AB!\n", pdev->name); + printk(KERN_INFO "%s: update your board or re-configure" + " the kernel\n", pdev->name); return -ENODEV; } #endif - au1xxx_start_ehc(dev); - - if (dev->resource[1].flags != IORESOURCE_IRQ) { + if (pdev->resource[1].flags != IORESOURCE_IRQ) { pr_debug("resource[1] is not IORESOURCE_IRQ"); - retval = -ENOMEM; + return -ENOMEM; } - hcd = usb_create_hcd(driver, &dev->dev, "Au1xxx"); + hcd = usb_create_hcd(&ehci_au1xxx_hc_driver, &pdev->dev, "Au1xxx"); if (!hcd) return -ENOMEM; - hcd->rsrc_start = dev->resource[0].start; - hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1; + + hcd->rsrc_start = pdev->resource[0].start; + hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1; if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { pr_debug("request_mem_region failed"); - retval = -EBUSY; + ret = -EBUSY; goto err1; } hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); if (!hcd->regs) { pr_debug("ioremap failed"); - retval = -ENOMEM; + ret = -ENOMEM; goto err2; } + au1xxx_start_ehc(); + ehci = hcd_to_ehci(hcd); ehci->caps = hcd->regs; ehci->regs = hcd->regs + HC_LENGTH(readl(&ehci->caps->hc_capbase)); /* cache this readonly data; minimize chip reads */ ehci->hcs_params = readl(&ehci->caps->hcs_params); - /* ehci_hcd_init(hcd_to_ehci(hcd)); */ - - retval = - usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED | IRQF_SHARED); - if (retval == 0) - return retval; + ret = usb_add_hcd(hcd, pdev->resource[1].start, + IRQF_DISABLED | IRQF_SHARED); + if (ret == 0) { + platform_set_drvdata(pdev, hcd); + return ret; + } - au1xxx_stop_ehc(dev); + au1xxx_stop_ehc(); iounmap(hcd->regs); err2: release_mem_region(hcd->rsrc_start, hcd->rsrc_len); err1: usb_put_hcd(hcd); - return retval; + return ret; } -/* may be called without controller electrically present */ -/* may be called with controller, bus, and devices active */ - -/** - * usb_ehci_hcd_au1xxx_remove - shutdown processing for Au1xxx-based HCDs - * @dev: USB Host Controller being removed - * Context: !in_interrupt() - * - * Reverses the effect of usb_ehci_hcd_au1xxx_probe(), first invoking - * the HCD's stop() method. It is always called from a thread - * context, normally "rmmod", "apmd", or something similar. - * - */ -void usb_ehci_au1xxx_remove(struct usb_hcd *hcd, struct platform_device *dev) +static int ehci_hcd_au1xxx_drv_remove(struct platform_device *pdev) { + struct usb_hcd *hcd = platform_get_drvdata(pdev); + usb_remove_hcd(hcd); iounmap(hcd->regs); release_mem_region(hcd->rsrc_start, hcd->rsrc_len); usb_put_hcd(hcd); - au1xxx_stop_ehc(dev); + au1xxx_stop_ehc(); + platform_set_drvdata(pdev, NULL); + + return 0; } -/*-------------------------------------------------------------------------*/ +#ifdef CONFIG_PM +static int ehci_hcd_au1xxx_drv_suspend(struct platform_device *pdev, + pm_message_t message) +{ + struct usb_hcd *hcd = platform_get_drvdata(pdev); + struct ehci_hcd *ehci = hcd_to_ehci(hcd); + unsigned long flags; + int rc; -static const struct hc_driver ehci_au1xxx_hc_driver = { - .description = hcd_name, - .product_desc = "Au1xxx EHCI", - .hcd_priv_size = sizeof(struct ehci_hcd), + return 0; + rc = 0; - /* - * generic hardware linkage - */ - .irq = ehci_irq, - .flags = HCD_MEMORY | HCD_USB2, + if (time_before(jiffies, ehci->next_statechange)) + msleep(10); - /* - * basic lifecycle operations + /* Root hub was already suspended. Disable irq emission and + * mark HW unaccessible, bail out if RH has been resumed. Use + * the spinlock to properly synchronize with possible pending + * RH suspend or resume activity. * - * FIXME -- ehci_init() doesn't do enough here. - * See ehci-ppc-soc for a complete implementation. - */ - .reset = ehci_init, - .start = ehci_run, - .stop = ehci_stop, - .shutdown = ehci_shutdown, - - /* - * managing i/o requests and associated device resources + * This is still racy as hcd->state is manipulated outside of + * any locks =P But that will be a different fix. */ - .urb_enqueue = ehci_urb_enqueue, - .urb_dequeue = ehci_urb_dequeue, - .endpoint_disable = ehci_endpoint_disable, + spin_lock_irqsave(&ehci->lock, flags); + if (hcd->state != HC_STATE_SUSPENDED) { + rc = -EINVAL; + goto bail; + } + ehci_writel(ehci, 0, &ehci->regs->intr_enable); + (void)ehci_readl(ehci, &ehci->regs->intr_enable); - /* - * scheduling support - */ - .get_frame_number = ehci_get_frame, + /* make sure snapshot being resumed re-enumerates everything */ + if (message.event == PM_EVENT_PRETHAW) { + ehci_halt(ehci); + ehci_reset(ehci); + } - /* - * root hub support - */ - .hub_status_data = ehci_hub_status_data, - .hub_control = ehci_hub_control, - .bus_suspend = ehci_bus_suspend, - .bus_resume = ehci_bus_resume, - .relinquish_port = ehci_relinquish_port, - .port_handed_over = ehci_port_handed_over, -}; + clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); -/*-------------------------------------------------------------------------*/ + au1xxx_stop_ehc(); -static int ehci_hcd_au1xxx_drv_probe(struct platform_device *pdev) -{ - struct usb_hcd *hcd = NULL; - int ret; +bail: + spin_unlock_irqrestore(&ehci->lock, flags); - pr_debug("In ehci_hcd_au1xxx_drv_probe\n"); + // could save FLADJ in case of Vaux power loss + // ... we'd only use it to handle clock skew - if (usb_disabled()) - return -ENODEV; - - /* FIXME we only want one one probe() not two */ - ret = usb_ehci_au1xxx_probe(&ehci_au1xxx_hc_driver, &hcd, pdev); - return ret; + return rc; } -static int ehci_hcd_au1xxx_drv_remove(struct platform_device *pdev) + +static int ehci_hcd_au1xxx_drv_resume(struct platform_device *pdev) { struct usb_hcd *hcd = platform_get_drvdata(pdev); + struct ehci_hcd *ehci = hcd_to_ehci(hcd); - /* FIXME we only want one one remove() not two */ - usb_ehci_au1xxx_remove(hcd, pdev); - return 0; -} + au1xxx_start_ehc(); - /*TBD*/ -/*static int ehci_hcd_au1xxx_drv_suspend(struct device *dev) -{ - struct platform_device *pdev = to_platform_device(dev); - struct usb_hcd *hcd = dev_get_drvdata(dev); + // maybe restore FLADJ - return 0; -} -static int ehci_hcd_au1xxx_drv_resume(struct device *dev) -{ - struct platform_device *pdev = to_platform_device(dev); - struct usb_hcd *hcd = dev_get_drvdata(dev); + if (time_before(jiffies, ehci->next_statechange)) + msleep(100); + + /* Mark hardware accessible again as we are out of D3 state by now */ + set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + + /* If CF is still set, we maintained PCI Vaux power. + * Just undo the effect of ehci_pci_suspend(). + */ + if (ehci_readl(ehci, &ehci->regs->configured_flag) == FLAG_CF) { + int mask = INTR_MASK; + + if (!hcd->self.root_hub->do_remote_wakeup) + mask &= ~STS_PCD; + ehci_writel(ehci, mask, &ehci->regs->intr_enable); + ehci_readl(ehci, &ehci->regs->intr_enable); + return 0; + } + + ehci_dbg(ehci, "lost power, restarting\n"); + usb_root_hub_lost_power(hcd->self.root_hub); + + /* Else reset, to cope with power loss or flush-to-storage + * style "resume" having let BIOS kick in during reboot. + */ + (void) ehci_halt(ehci); + (void) ehci_reset(ehci); + + /* emptying the schedule aborts any urbs */ + spin_lock_irq(&ehci->lock); + if (ehci->reclaim) + end_unlink_async(ehci); + ehci_work(ehci); + spin_unlock_irq(&ehci->lock); + + ehci_writel(ehci, ehci->command, &ehci->regs->command); + ehci_writel(ehci, FLAG_CF, &ehci->regs->configured_flag); + ehci_readl(ehci, &ehci->regs->command); /* unblock posted writes */ + + /* here we "know" root ports should always stay powered */ + ehci_port_power(ehci, 1); + + hcd->state = HC_STATE_SUSPENDED; return 0; } -*/ -MODULE_ALIAS("platform:au1xxx-ehci"); + +#else +#define ehci_hcd_au1xxx_drv_suspend NULL +#define ehci_hcd_au1xxx_drv_resume NULL +#endif + static struct platform_driver ehci_hcd_au1xxx_driver = { - .probe = ehci_hcd_au1xxx_drv_probe, - .remove = ehci_hcd_au1xxx_drv_remove, - .shutdown = usb_hcd_platform_shutdown, - /*.suspend = ehci_hcd_au1xxx_drv_suspend, */ - /*.resume = ehci_hcd_au1xxx_drv_resume, */ + .probe = ehci_hcd_au1xxx_drv_probe, + .remove = ehci_hcd_au1xxx_drv_remove, + .shutdown = usb_hcd_platform_shutdown, + .suspend = ehci_hcd_au1xxx_drv_suspend, + .resume = ehci_hcd_au1xxx_drv_resume, .driver = { - .name = "au1xxx-ehci", + .name = "au1xxx-ehci", + .owner = THIS_MODULE, } }; + +MODULE_ALIAS("platform:au1xxx-ehci"); diff --git a/drivers/usb/host/ehci-dbg.c b/drivers/usb/host/ehci-dbg.c index 0f82fdcaef0..b0f8ed5a7fb 100644 --- a/drivers/usb/host/ehci-dbg.c +++ b/drivers/usb/host/ehci-dbg.c @@ -676,7 +676,7 @@ static ssize_t fill_registers_buffer(struct debug_buffer *buf) "%s\n" "SUSPENDED (no register access)\n", hcd->self.controller->bus->name, - hcd->self.controller->bus_id, + dev_name(hcd->self.controller), hcd->product_desc); goto done; } @@ -688,7 +688,7 @@ static ssize_t fill_registers_buffer(struct debug_buffer *buf) "%s\n" "EHCI %x.%02x, hcd state %d\n", hcd->self.controller->bus->name, - hcd->self.controller->bus_id, + dev_name(hcd->self.controller), hcd->product_desc, i >> 8, i & 0x0ff, hcd->state); size -= temp; diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c index 7370d6187c6..01c3da34f67 100644 --- a/drivers/usb/host/ehci-fsl.c +++ b/drivers/usb/host/ehci-fsl.c @@ -56,7 +56,7 @@ int usb_hcd_fsl_probe(const struct hc_driver *driver, pdata = (struct fsl_usb2_platform_data *)pdev->dev.platform_data; if (!pdata) { dev_err(&pdev->dev, - "No platform data for %s.\n", pdev->dev.bus_id); + "No platform data for %s.\n", dev_name(&pdev->dev)); return -ENODEV; } @@ -69,7 +69,7 @@ int usb_hcd_fsl_probe(const struct hc_driver *driver, (pdata->operating_mode == FSL_USB2_DR_OTG))) { dev_err(&pdev->dev, "Non Host Mode configured for %s. Wrong driver linked.\n", - pdev->dev.bus_id); + dev_name(&pdev->dev)); return -ENODEV; } @@ -77,12 +77,12 @@ int usb_hcd_fsl_probe(const struct hc_driver *driver, if (!res) { dev_err(&pdev->dev, "Found HC with no IRQ. Check %s setup!\n", - pdev->dev.bus_id); + dev_name(&pdev->dev)); return -ENODEV; } irq = res->start; - hcd = usb_create_hcd(driver, &pdev->dev, pdev->dev.bus_id); + hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { retval = -ENOMEM; goto err1; @@ -92,7 +92,7 @@ int usb_hcd_fsl_probe(const struct hc_driver *driver, if (!res) { dev_err(&pdev->dev, "Found HC with no register addr. Check %s setup!\n", - pdev->dev.bus_id); + dev_name(&pdev->dev)); retval = -ENODEV; goto err2; } @@ -132,7 +132,7 @@ int usb_hcd_fsl_probe(const struct hc_driver *driver, err2: usb_put_hcd(hcd); err1: - dev_err(&pdev->dev, "init %s fail, %d\n", pdev->dev.bus_id, retval); + dev_err(&pdev->dev, "init %s fail, %d\n", dev_name(&pdev->dev), retval); return retval; } @@ -230,8 +230,13 @@ static void mpc83xx_usb_setup(struct usb_hcd *hcd) /* put controller in host mode. */ ehci_writel(ehci, 0x00000003, non_ehci + FSL_SOC_USB_USBMODE); +#ifdef CONFIG_PPC_85xx + out_be32(non_ehci + FSL_SOC_USB_PRICTRL, 0x00000008); + out_be32(non_ehci + FSL_SOC_USB_AGECNTTHRSH, 0x00000080); +#else out_be32(non_ehci + FSL_SOC_USB_PRICTRL, 0x0000000c); out_be32(non_ehci + FSL_SOC_USB_AGECNTTHRSH, 0x00000040); +#endif out_be32(non_ehci + FSL_SOC_USB_SICTRL, 0x00000001); } diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 369a8a5ea7b..d9d53f289ca 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -84,7 +84,7 @@ static const char hcd_name [] = "ehci_hcd"; #define EHCI_IAA_MSECS 10 /* arbitrary */ #define EHCI_IO_JIFFIES (HZ/10) /* io watchdog > irq_thresh */ #define EHCI_ASYNC_JIFFIES (HZ/20) /* async idle timeout */ -#define EHCI_SHRINK_JIFFIES (HZ/200) /* async qh unlink delay */ +#define EHCI_SHRINK_FRAMES 5 /* async qh unlink delay */ /* Initial IRQ latency: faster than hw default */ static int log2_irq_thresh = 0; // 0 to 6 diff --git a/drivers/usb/host/ehci-ixp4xx.c b/drivers/usb/host/ehci-ixp4xx.c index 9d042f22009..f9575c40912 100644 --- a/drivers/usb/host/ehci-ixp4xx.c +++ b/drivers/usb/host/ehci-ixp4xx.c @@ -77,12 +77,12 @@ static int ixp4xx_ehci_probe(struct platform_device *pdev) if (!res) { dev_err(&pdev->dev, "Found HC with no IRQ. Check %s setup!\n", - pdev->dev.bus_id); + dev_name(&pdev->dev)); return -ENODEV; } irq = res->start; - hcd = usb_create_hcd(driver, &pdev->dev, pdev->dev.bus_id); + hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { retval = -ENOMEM; goto fail_create_hcd; @@ -92,7 +92,7 @@ static int ixp4xx_ehci_probe(struct platform_device *pdev) if (!res) { dev_err(&pdev->dev, "Found HC with no register addr. Check %s setup!\n", - pdev->dev.bus_id); + dev_name(&pdev->dev)); retval = -ENODEV; goto fail_request_resource; } @@ -126,7 +126,7 @@ fail_ioremap: fail_request_resource: usb_put_hcd(hcd); fail_create_hcd: - dev_err(&pdev->dev, "init %s fail, %d\n", pdev->dev.bus_id, retval); + dev_err(&pdev->dev, "init %s fail, %d\n", dev_name(&pdev->dev), retval); return retval; } diff --git a/drivers/usb/host/ehci-orion.c b/drivers/usb/host/ehci-orion.c index ab625f0ba1d..5fbdc14e63b 100644 --- a/drivers/usb/host/ehci-orion.c +++ b/drivers/usb/host/ehci-orion.c @@ -204,7 +204,7 @@ static int __init ehci_orion_drv_probe(struct platform_device *pdev) if (irq <= 0) { dev_err(&pdev->dev, "Found HC with no IRQ. Check %s setup!\n", - pdev->dev.bus_id); + dev_name(&pdev->dev)); err = -ENODEV; goto err1; } @@ -213,7 +213,7 @@ static int __init ehci_orion_drv_probe(struct platform_device *pdev) if (!res) { dev_err(&pdev->dev, "Found HC with no register addr. Check %s setup!\n", - pdev->dev.bus_id); + dev_name(&pdev->dev)); err = -ENODEV; goto err1; } @@ -233,7 +233,7 @@ static int __init ehci_orion_drv_probe(struct platform_device *pdev) } hcd = usb_create_hcd(&ehci_orion_hc_driver, - &pdev->dev, pdev->dev.bus_id); + &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { err = -ENOMEM; goto err3; @@ -276,7 +276,7 @@ err2: release_mem_region(res->start, res->end - res->start + 1); err1: dev_err(&pdev->dev, "init %s fail, %d\n", - pdev->dev.bus_id, err); + dev_name(&pdev->dev), err); return err; } diff --git a/drivers/usb/host/ehci-ps3.c b/drivers/usb/host/ehci-ps3.c index 37e6abeb794..0eba894bcb0 100644 --- a/drivers/usb/host/ehci-ps3.c +++ b/drivers/usb/host/ehci-ps3.c @@ -128,7 +128,7 @@ static int ps3_ehci_probe(struct ps3_system_bus_device *dev) dev->core.dma_mask = &dummy_mask; /* FIXME: for improper usb code */ - hcd = usb_create_hcd(&ps3_ehci_hc_driver, &dev->core, dev->core.bus_id); + hcd = usb_create_hcd(&ps3_ehci_hc_driver, &dev->core, dev_name(&dev->core)); if (!hcd) { dev_dbg(&dev->core, "%s:%d: usb_create_hcd failed\n", __func__, diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c index b85b54160cd..2622b6596d7 100644 --- a/drivers/usb/host/ehci-q.c +++ b/drivers/usb/host/ehci-q.c @@ -1116,8 +1116,7 @@ static void scan_async (struct ehci_hcd *ehci) struct ehci_qh *qh; enum ehci_timer_action action = TIMER_IO_WATCHDOG; - if (!++(ehci->stamp)) - ehci->stamp++; + ehci->stamp = ehci_readl(ehci, &ehci->regs->frame_index); timer_action_done (ehci, TIMER_ASYNC_SHRINK); rescan: qh = ehci->async->qh_next.qh; @@ -1142,18 +1141,20 @@ rescan: } } - /* unlink idle entries, reducing HC PCI usage as well + /* unlink idle entries, reducing DMA usage as well * as HCD schedule-scanning costs. delay for any qh * we just scanned, there's a not-unusual case that it * doesn't stay idle for long. * (plus, avoids some kind of re-activation race.) */ - if (list_empty (&qh->qtd_list)) { - if (qh->stamp == ehci->stamp) + if (list_empty(&qh->qtd_list) + && qh->qh_state == QH_STATE_LINKED) { + if (!ehci->reclaim + && ((ehci->stamp - qh->stamp) & 0x1fff) + >= (EHCI_SHRINK_FRAMES * 8)) + start_unlink_async(ehci, qh); + else action = TIMER_ASYNC_SHRINK; - else if (!ehci->reclaim - && qh->qh_state == QH_STATE_LINKED) - start_unlink_async (ehci, qh); } qh = qh->qh_next.qh; diff --git a/drivers/usb/host/ehci.h b/drivers/usb/host/ehci.h index 90245fd8bac..5799298364f 100644 --- a/drivers/usb/host/ehci.h +++ b/drivers/usb/host/ehci.h @@ -198,7 +198,10 @@ timer_action (struct ehci_hcd *ehci, enum ehci_timer_action action) break; // case TIMER_ASYNC_SHRINK: default: - t = EHCI_SHRINK_JIFFIES; + /* add a jiffie since we synch against the + * 8 KHz uframe counter. + */ + t = DIV_ROUND_UP(EHCI_SHRINK_FRAMES * HZ, 1000) + 1; break; } mod_timer(&ehci->watchdog, t + jiffies); diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c index 20b9a0d0742..31178e10cbb 100644 --- a/drivers/usb/host/isp116x-hcd.c +++ b/drivers/usb/host/isp116x-hcd.c @@ -94,6 +94,10 @@ static void write_ptddata_to_fifo(struct isp116x *isp116x, void *buf, int len) u16 w; int quot = len % 4; + /* buffer is already in 'usb data order', which is LE. */ + /* When reading buffer as u16, we have to take care byte order */ + /* doesn't get mixed up */ + if ((unsigned long)dp2 & 1) { /* not aligned */ for (; len > 1; len -= 2) { @@ -105,8 +109,11 @@ static void write_ptddata_to_fifo(struct isp116x *isp116x, void *buf, int len) isp116x_write_data16(isp116x, (u16) * dp); } else { /* aligned */ - for (; len > 1; len -= 2) - isp116x_raw_write_data16(isp116x, *dp2++); + for (; len > 1; len -= 2) { + /* Keep byte order ! */ + isp116x_raw_write_data16(isp116x, cpu_to_le16(*dp2++)); + } + if (len) isp116x_write_data16(isp116x, 0xff & *((u8 *) dp2)); } @@ -124,6 +131,10 @@ static void read_ptddata_from_fifo(struct isp116x *isp116x, void *buf, int len) u16 w; int quot = len % 4; + /* buffer is already in 'usb data order', which is LE. */ + /* When reading buffer as u16, we have to take care byte order */ + /* doesn't get mixed up */ + if ((unsigned long)dp2 & 1) { /* not aligned */ for (; len > 1; len -= 2) { @@ -131,12 +142,16 @@ static void read_ptddata_from_fifo(struct isp116x *isp116x, void *buf, int len) *dp++ = w & 0xff; *dp++ = (w >> 8) & 0xff; } + if (len) *dp = 0xff & isp116x_read_data16(isp116x); } else { /* aligned */ - for (; len > 1; len -= 2) - *dp2++ = isp116x_raw_read_data16(isp116x); + for (; len > 1; len -= 2) { + /* Keep byte order! */ + *dp2++ = le16_to_cpu(isp116x_raw_read_data16(isp116x)); + } + if (len) *(u8 *) dp2 = 0xff & isp116x_read_data16(isp116x); } @@ -1592,7 +1607,7 @@ static int __devinit isp116x_probe(struct platform_device *pdev) } /* allocate and initialize hcd */ - hcd = usb_create_hcd(&isp116x_hc_driver, &pdev->dev, pdev->dev.bus_id); + hcd = usb_create_hcd(&isp116x_hc_driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { ret = -ENOMEM; goto err5; diff --git a/drivers/usb/host/isp1760-hcd.c b/drivers/usb/host/isp1760-hcd.c index 65aa5ecf569..c858f2adb92 100644 --- a/drivers/usb/host/isp1760-hcd.c +++ b/drivers/usb/host/isp1760-hcd.c @@ -38,6 +38,7 @@ struct isp1760_hcd { unsigned i_thresh; unsigned long reset_done; unsigned long next_statechange; + unsigned int devflags; }; static inline struct isp1760_hcd *hcd_to_priv(struct usb_hcd *hcd) @@ -378,9 +379,31 @@ static int isp1760_hc_setup(struct usb_hcd *hcd) { struct isp1760_hcd *priv = hcd_to_priv(hcd); int result; - u32 scratch; + u32 scratch, hwmode; + + /* Setup HW Mode Control: This assumes a level active-low interrupt */ + hwmode = HW_DATA_BUS_32BIT; + + if (priv->devflags & ISP1760_FLAG_BUS_WIDTH_16) + hwmode &= ~HW_DATA_BUS_32BIT; + if (priv->devflags & ISP1760_FLAG_ANALOG_OC) + hwmode |= HW_ANA_DIGI_OC; + if (priv->devflags & ISP1760_FLAG_DACK_POL_HIGH) + hwmode |= HW_DACK_POL_HIGH; + if (priv->devflags & ISP1760_FLAG_DREQ_POL_HIGH) + hwmode |= HW_DREQ_POL_HIGH; + + /* + * We have to set this first in case we're in 16-bit mode. + * Write it twice to ensure correct upper bits if switching + * to 16-bit mode. + */ + isp1760_writel(hwmode, hcd->regs + HC_HW_MODE_CTRL); + isp1760_writel(hwmode, hcd->regs + HC_HW_MODE_CTRL); isp1760_writel(0xdeadbabe, hcd->regs + HC_SCRATCH_REG); + /* Change bus pattern */ + scratch = isp1760_readl(hcd->regs + HC_CHIP_ID_REG); scratch = isp1760_readl(hcd->regs + HC_SCRATCH_REG); if (scratch != 0xdeadbabe) { printk(KERN_ERR "ISP1760: Scratch test failed.\n"); @@ -403,17 +426,29 @@ static int isp1760_hc_setup(struct usb_hcd *hcd) /* Step 11 passed */ - isp1760_writel(INTERRUPT_ENABLE_MASK, hcd->regs + HC_INTERRUPT_REG); - isp1760_writel(INTERRUPT_ENABLE_MASK, hcd->regs + HC_INTERRUPT_ENABLE); + isp1760_info(priv, "bus width: %d, oc: %s\n", + (priv->devflags & ISP1760_FLAG_BUS_WIDTH_16) ? + 16 : 32, (priv->devflags & ISP1760_FLAG_ANALOG_OC) ? + "analog" : "digital"); /* ATL reset */ - scratch = isp1760_readl(hcd->regs + HC_HW_MODE_CTRL); - isp1760_writel(scratch | ALL_ATX_RESET, hcd->regs + HC_HW_MODE_CTRL); + isp1760_writel(hwmode | ALL_ATX_RESET, hcd->regs + HC_HW_MODE_CTRL); mdelay(10); - isp1760_writel(scratch, hcd->regs + HC_HW_MODE_CTRL); + isp1760_writel(hwmode, hcd->regs + HC_HW_MODE_CTRL); - isp1760_writel(PORT1_POWER | PORT1_INIT2, hcd->regs + HC_PORT1_CTRL); - mdelay(10); + isp1760_writel(INTERRUPT_ENABLE_MASK, hcd->regs + HC_INTERRUPT_REG); + isp1760_writel(INTERRUPT_ENABLE_MASK, hcd->regs + HC_INTERRUPT_ENABLE); + + /* + * PORT 1 Control register of the ISP1760 is the OTG control + * register on ISP1761. + */ + if (!(priv->devflags & ISP1760_FLAG_ISP1761) && + !(priv->devflags & ISP1760_FLAG_PORT1_DIS)) { + isp1760_writel(PORT1_POWER | PORT1_INIT2, + hcd->regs + HC_PORT1_CTRL); + mdelay(10); + } priv->hcs_params = isp1760_readl(hcd->regs + HC_HCSPARAMS); @@ -453,8 +488,7 @@ static int isp1760_run(struct usb_hcd *hcd) hcd->state = HC_STATE_RUNNING; isp1760_enable_interrupts(hcd); temp = isp1760_readl(hcd->regs + HC_HW_MODE_CTRL); - temp |= FINAL_HW_CONFIG; - isp1760_writel(temp, hcd->regs + HC_HW_MODE_CTRL); + isp1760_writel(temp | HW_GLOBAL_INTR_EN, hcd->regs + HC_HW_MODE_CTRL); command = isp1760_readl(hcd->regs + HC_USBCMD); command &= ~(CMD_LRESET|CMD_RESET); @@ -782,8 +816,8 @@ static void enqueue_one_int_qtd(u32 int_regs, u32 payload, qtd->status |= slot << 16; } -void enqueue_an_ATL_packet(struct usb_hcd *hcd, struct isp1760_qh *qh, - struct isp1760_qtd *qtd) +static void enqueue_an_ATL_packet(struct usb_hcd *hcd, struct isp1760_qh *qh, + struct isp1760_qtd *qtd) { struct isp1760_hcd *priv = hcd_to_priv(hcd); u32 skip_map, or_map; @@ -816,8 +850,8 @@ void enqueue_an_ATL_packet(struct usb_hcd *hcd, struct isp1760_qh *qh, isp1760_writel(buffstatus, hcd->regs + HC_BUFFER_STATUS_REG); } -void enqueue_an_INT_packet(struct usb_hcd *hcd, struct isp1760_qh *qh, - struct isp1760_qtd *qtd) +static void enqueue_an_INT_packet(struct usb_hcd *hcd, struct isp1760_qh *qh, + struct isp1760_qtd *qtd) { struct isp1760_hcd *priv = hcd_to_priv(hcd); u32 skip_map, or_map; @@ -1592,7 +1626,7 @@ static int isp1760_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, struct inter_packet_info *ints; u32 i; u32 reg_base, or_reg, skip_reg; - int flags; + unsigned long flags; struct ptd ptd; switch (usb_pipetype(urb->pipe)) { @@ -2061,7 +2095,7 @@ static void isp1760_endpoint_disable(struct usb_hcd *usb_hcd, struct isp1760_hcd *priv = hcd_to_priv(usb_hcd); struct isp1760_qh *qh; struct isp1760_qtd *qtd; - u32 flags; + unsigned long flags; spin_lock_irqsave(&priv->lock, flags); qh = ep->hcpriv; @@ -2112,6 +2146,7 @@ static int isp1760_get_frame(struct usb_hcd *hcd) static void isp1760_stop(struct usb_hcd *hcd) { struct isp1760_hcd *priv = hcd_to_priv(hcd); + u32 temp; isp1760_hub_control(hcd, ClearPortFeature, USB_PORT_FEAT_POWER, 1, NULL, 0); @@ -2120,7 +2155,8 @@ static void isp1760_stop(struct usb_hcd *hcd) spin_lock_irq(&priv->lock); ehci_reset(priv); /* Disable IRQ */ - isp1760_writel(HW_DATA_BUS_32BIT, hcd->regs + HC_HW_MODE_CTRL); + temp = isp1760_readl(hcd->regs + HC_HW_MODE_CTRL); + isp1760_writel(temp &= ~HW_GLOBAL_INTR_EN, hcd->regs + HC_HW_MODE_CTRL); spin_unlock_irq(&priv->lock); isp1760_writel(0, hcd->regs + HC_CONFIGFLAG); @@ -2128,10 +2164,11 @@ static void isp1760_stop(struct usb_hcd *hcd) static void isp1760_shutdown(struct usb_hcd *hcd) { - u32 command; + u32 command, temp; isp1760_stop(hcd); - isp1760_writel(HW_DATA_BUS_32BIT, hcd->regs + HC_HW_MODE_CTRL); + temp = isp1760_readl(hcd->regs + HC_HW_MODE_CTRL); + isp1760_writel(temp &= ~HW_GLOBAL_INTR_EN, hcd->regs + HC_HW_MODE_CTRL); command = isp1760_readl(hcd->regs + HC_USBCMD); command &= ~CMD_RUN; @@ -2183,7 +2220,8 @@ void deinit_kmem_cache(void) } struct usb_hcd *isp1760_register(u64 res_start, u64 res_len, int irq, - u64 irqflags, struct device *dev, const char *busname) + u64 irqflags, struct device *dev, const char *busname, + unsigned int devflags) { struct usb_hcd *hcd; struct isp1760_hcd *priv; @@ -2195,11 +2233,12 @@ struct usb_hcd *isp1760_register(u64 res_start, u64 res_len, int irq, /* prevent usb-core allocating DMA pages */ dev->dma_mask = NULL; - hcd = usb_create_hcd(&isp1760_hc_driver, dev, dev->bus_id); + hcd = usb_create_hcd(&isp1760_hc_driver, dev, dev_name(dev)); if (!hcd) return ERR_PTR(-ENOMEM); priv = hcd_to_priv(hcd); + priv->devflags = devflags; init_memory(priv); hcd->regs = ioremap(res_start, res_len); if (!hcd->regs) { diff --git a/drivers/usb/host/isp1760-hcd.h b/drivers/usb/host/isp1760-hcd.h index 3d86d0f6b14..6473dd86993 100644 --- a/drivers/usb/host/isp1760-hcd.h +++ b/drivers/usb/host/isp1760-hcd.h @@ -3,7 +3,8 @@ /* exports for if */ struct usb_hcd *isp1760_register(u64 res_start, u64 res_len, int irq, - u64 irqflags, struct device *dev, const char *busname); + u64 irqflags, struct device *dev, const char *busname, + unsigned int devflags); int init_kmem_once(void); void deinit_kmem_cache(void); @@ -31,6 +32,7 @@ void deinit_kmem_cache(void); /* Configuration Register */ #define HC_HW_MODE_CTRL 0x300 #define ALL_ATX_RESET (1 << 31) +#define HW_ANA_DIGI_OC (1 << 15) #define HW_DATA_BUS_32BIT (1 << 8) #define HW_DACK_POL_HIGH (1 << 6) #define HW_DREQ_POL_HIGH (1 << 5) @@ -56,13 +58,14 @@ void deinit_kmem_cache(void); #define PORT1_POWER (3 << 3) #define PORT1_INIT1 (1 << 7) #define PORT1_INIT2 (1 << 23) +#define HW_OTG_CTRL_SET 0x374 +#define HW_OTG_CTRL_CLR 0x376 /* Interrupt Register */ #define HC_INTERRUPT_REG 0x310 #define HC_INTERRUPT_ENABLE 0x314 #define INTERRUPT_ENABLE_MASK (HC_INTL_INT | HC_ATL_INT | HC_EOT_INT) -#define FINAL_HW_CONFIG (HW_GLOBAL_INTR_EN | HW_DATA_BUS_32BIT) #define HC_ISO_INT (1 << 9) #define HC_ATL_INT (1 << 8) @@ -122,6 +125,19 @@ typedef void (packet_enqueue)(struct usb_hcd *hcd, struct isp1760_qh *qh, #define isp1760_err(priv, fmt, args...) \ dev_err(priv_to_hcd(priv)->self.controller, fmt, ##args) +/* + * Device flags that can vary from board to board. All of these + * indicate the most "atypical" case, so that a devflags of 0 is + * a sane default configuration. + */ +#define ISP1760_FLAG_PORT1_DIS 0x00000001 /* Port 1 disabled */ +#define ISP1760_FLAG_BUS_WIDTH_16 0x00000002 /* 16-bit data bus width */ +#define ISP1760_FLAG_OTG_EN 0x00000004 /* Port 1 supports OTG */ +#define ISP1760_FLAG_ANALOG_OC 0x00000008 /* Analog overcurrent */ +#define ISP1760_FLAG_DACK_POL_HIGH 0x00000010 /* DACK active high */ +#define ISP1760_FLAG_DREQ_POL_HIGH 0x00000020 /* DREQ active high */ +#define ISP1760_FLAG_ISP1761 0x00000040 /* Chip is ISP1761 */ + /* chip memory management */ struct memory_chunk { unsigned int start; diff --git a/drivers/usb/host/isp1760-if.c b/drivers/usb/host/isp1760-if.c index c9db3fe9872..051ef7b6bdc 100644 --- a/drivers/usb/host/isp1760-if.c +++ b/drivers/usb/host/isp1760-if.c @@ -35,13 +35,15 @@ static int of_isp1760_probe(struct of_device *dev, int virq; u64 res_len; int ret; + const unsigned int *prop; + unsigned int devflags = 0; ret = of_address_to_resource(dp, 0, &memory); if (ret) return -ENXIO; res = request_mem_region(memory.start, memory.end - memory.start + 1, - dev->dev.bus_id); + dev_name(&dev->dev)); if (!res) return -EBUSY; @@ -55,8 +57,32 @@ static int of_isp1760_probe(struct of_device *dev, virq = irq_create_of_mapping(oirq.controller, oirq.specifier, oirq.size); + if (of_device_is_compatible(dp, "nxp,usb-isp1761")) + devflags |= ISP1760_FLAG_ISP1761; + + if (of_get_property(dp, "port1-disable", NULL) != NULL) + devflags |= ISP1760_FLAG_PORT1_DIS; + + /* Some systems wire up only 16 of the 32 data lines */ + prop = of_get_property(dp, "bus-width", NULL); + if (prop && *prop == 16) + devflags |= ISP1760_FLAG_BUS_WIDTH_16; + + if (of_get_property(dp, "port1-otg", NULL) != NULL) + devflags |= ISP1760_FLAG_OTG_EN; + + if (of_get_property(dp, "analog-oc", NULL) != NULL) + devflags |= ISP1760_FLAG_ANALOG_OC; + + if (of_get_property(dp, "dack-polarity", NULL) != NULL) + devflags |= ISP1760_FLAG_DACK_POL_HIGH; + + if (of_get_property(dp, "dreq-polarity", NULL) != NULL) + devflags |= ISP1760_FLAG_DREQ_POL_HIGH; + hcd = isp1760_register(memory.start, res_len, virq, - IRQF_SHARED | IRQF_DISABLED, &dev->dev, dev->dev.bus_id); + IRQF_SHARED | IRQF_DISABLED, &dev->dev, dev_name(&dev->dev), + devflags); if (IS_ERR(hcd)) { ret = PTR_ERR(hcd); goto release_reg; @@ -87,6 +113,9 @@ static struct of_device_id of_isp1760_match[] = { { .compatible = "nxp,usb-isp1760", }, + { + .compatible = "nxp,usb-isp1761", + }, { }, }; MODULE_DEVICE_TABLE(of, of_isp1760_match); @@ -116,6 +145,7 @@ static int __devinit isp1761_pci_probe(struct pci_dev *dev, int length; int status = 1; struct usb_hcd *hcd; + unsigned int devflags = 0; if (usb_disabled()) return -ENODEV; @@ -200,7 +230,8 @@ static int __devinit isp1761_pci_probe(struct pci_dev *dev, dev->dev.dma_mask = NULL; hcd = isp1760_register(pci_mem_phy0, length, dev->irq, - IRQF_SHARED | IRQF_DISABLED, &dev->dev, dev->dev.bus_id); + IRQF_SHARED | IRQF_DISABLED, &dev->dev, dev_name(&dev->dev), + devflags); pci_set_drvdata(dev, hcd); if (!hcd) return 0; diff --git a/drivers/usb/host/ohci-at91.c b/drivers/usb/host/ohci-at91.c index e534f9de0f0..a5d8e550d89 100644 --- a/drivers/usb/host/ohci-at91.c +++ b/drivers/usb/host/ohci-at91.c @@ -91,7 +91,7 @@ static void at91_stop_hc(struct platform_device *pdev) /*-------------------------------------------------------------------------*/ -static int usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *); +static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *); /* configure so an HC device and id are always provided */ /* always called with process context; sleeping is OK */ @@ -184,13 +184,14 @@ static int usb_hcd_at91_probe(const struct hc_driver *driver, * context, "rmmod" or something similar. * */ -static int usb_hcd_at91_remove(struct usb_hcd *hcd, +static void usb_hcd_at91_remove(struct usb_hcd *hcd, struct platform_device *pdev) { usb_remove_hcd(hcd); at91_stop_hc(pdev); iounmap(hcd->regs); release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + usb_put_hcd(hcd); if (cpu_is_at91sam9261()) clk_put(hclk); @@ -199,7 +200,6 @@ static int usb_hcd_at91_remove(struct usb_hcd *hcd, fclk = iclk = hclk = NULL; dev_set_drvdata(&pdev->dev, NULL); - return 0; } /*-------------------------------------------------------------------------*/ @@ -309,7 +309,8 @@ static int ohci_hcd_at91_drv_remove(struct platform_device *pdev) } device_init_wakeup(&pdev->dev, 0); - return usb_hcd_at91_remove(platform_get_drvdata(pdev), pdev); + usb_hcd_at91_remove(platform_get_drvdata(pdev), pdev); + return 0; } #ifdef CONFIG_PM diff --git a/drivers/usb/host/ohci-au1xxx.c b/drivers/usb/host/ohci-au1xxx.c index f90fe0c7373..c0948008fe3 100644 --- a/drivers/usb/host/ohci-au1xxx.c +++ b/drivers/usb/host/ohci-au1xxx.c @@ -8,7 +8,7 @@ * Bus Glue for AMD Alchemy Au1xxx * * Written by Christopher Hoover <ch@hpl.hp.com> - * Based on fragments of previous driver by Rusell King et al. + * Based on fragments of previous driver by Russell King et al. * * Modified for LH7A404 from ohci-sa1111.c * by Durgesh Pattamatta <pattamattad@sharpsec.com> @@ -34,7 +34,8 @@ #ifdef __LITTLE_ENDIAN #define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C) #elif __BIG_ENDIAN -#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | USBH_ENABLE_BE) +#define USBH_ENABLE_INIT (USBH_ENABLE_CE | USBH_ENABLE_E | USBH_ENABLE_C | \ + USBH_ENABLE_BE) #else #error not byte order defined #endif @@ -46,213 +47,87 @@ #define USB_MCFG_RDCOMB (1<<30) #define USB_MCFG_SSDEN (1<<23) #define USB_MCFG_OHCCLKEN (1<<16) +#ifdef CONFIG_DMA_COHERENT #define USB_MCFG_UCAM (1<<7) +#else +#define USB_MCFG_UCAM (0) +#endif #define USB_MCFG_OBMEN (1<<1) #define USB_MCFG_OMEMEN (1<<0) #define USBH_ENABLE_CE USB_MCFG_OHCCLKEN -#ifdef CONFIG_DMA_COHERENT -#define USBH_ENABLE_INIT (USB_MCFG_OHCCLKEN \ - | USB_MCFG_PFEN | USB_MCFG_RDCOMB \ - | USB_MCFG_SSDEN | USB_MCFG_UCAM \ - | USB_MCFG_OBMEN | USB_MCFG_OMEMEN) -#else -#define USBH_ENABLE_INIT (USB_MCFG_OHCCLKEN \ - | USB_MCFG_PFEN | USB_MCFG_RDCOMB \ - | USB_MCFG_SSDEN \ - | USB_MCFG_OBMEN | USB_MCFG_OMEMEN) -#endif + +#define USBH_ENABLE_INIT (USB_MCFG_PFEN | USB_MCFG_RDCOMB | \ + USBH_ENABLE_CE | USB_MCFG_SSDEN | \ + USB_MCFG_UCAM | \ + USB_MCFG_OBMEN | USB_MCFG_OMEMEN) + #define USBH_DISABLE (USB_MCFG_OBMEN | USB_MCFG_OMEMEN) #endif /* Au1200 */ extern int usb_disabled(void); -/*-------------------------------------------------------------------------*/ - -static void au1xxx_start_ohc(struct platform_device *dev) +static void au1xxx_start_ohc(void) { - printk(KERN_DEBUG __FILE__ - ": starting Au1xxx OHCI USB Controller\n"); - /* enable host controller */ - #ifndef CONFIG_SOC_AU1200 - au_writel(USBH_ENABLE_CE, USB_HOST_CONFIG); + au_sync(); udelay(1000); - au_writel(USBH_ENABLE_INIT, USB_HOST_CONFIG); - udelay(1000); - -#else /* Au1200 */ - /* write HW defaults again in case Yamon cleared them */ - if (au_readl(USB_HOST_CONFIG) == 0) { - au_writel(0x00d02000, USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); - udelay(1000); - } - au_writel(USBH_ENABLE_CE | au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); + au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG); + au_sync(); udelay(1000); - au_writel(USBH_ENABLE_INIT | au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); - udelay(1000); - -#endif /* Au1200 */ -#ifndef CONFIG_SOC_AU1200 /* wait for reset complete (read register twice; see au1500 errata) */ while (au_readl(USB_HOST_CONFIG), !(au_readl(USB_HOST_CONFIG) & USBH_ENABLE_RD)) -#endif udelay(1000); - printk(KERN_DEBUG __FILE__ - ": Clock to USB host has been enabled \n"); -} - -static void au1xxx_stop_ohc(struct platform_device *dev) -{ - printk(KERN_DEBUG __FILE__ - ": stopping Au1xxx OHCI USB Controller\n"); - -#ifndef CONFIG_SOC_AU1200 - - /* Disable clock */ - au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG); - #else /* Au1200 */ - - /* Disable mem */ - au_writel(~USBH_DISABLE & au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG); + au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_CE, USB_HOST_CONFIG); + au_sync(); udelay(1000); - /* Disable clock */ - au_writel(~USBH_ENABLE_CE & au_readl(USB_HOST_CONFIG), USB_HOST_CONFIG); - au_readl(USB_HOST_CONFIG); + + au_writel(au_readl(USB_HOST_CONFIG) | USBH_ENABLE_INIT, USB_HOST_CONFIG); + au_sync(); + udelay(2000); #endif /* Au1200 */ } - -/*-------------------------------------------------------------------------*/ - -/* configure so an HC device and id are always provided */ -/* always called with process context; sleeping is OK */ - - -/** - * usb_ohci_au1xxx_probe - initialize Au1xxx-based HCDs - * Context: !in_interrupt() - * - * Allocates basic resources for this USB host controller, and - * then invokes the start() method for the HCD associated with it - * through the hotplug entry's driver_data. - * - */ -static int usb_ohci_au1xxx_probe(const struct hc_driver *driver, - struct platform_device *dev) +static void au1xxx_stop_ohc(void) { - int retval; - struct usb_hcd *hcd; - -#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT) - /* Au1200 AB USB does not support coherent memory */ - if (!(read_c0_prid() & 0xff)) { - pr_info("%s: this is chip revision AB !!\n", - dev->name); - pr_info("%s: update your board or re-configure the kernel\n", - dev->name); - return -ENODEV; - } +#ifdef CONFIG_SOC_AU1200 + /* Disable mem */ + au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_DISABLE, USB_HOST_CONFIG); + au_sync(); + udelay(1000); #endif - - if (dev->resource[1].flags != IORESOURCE_IRQ) { - pr_debug("resource[1] is not IORESOURCE_IRQ\n"); - return -ENOMEM; - } - - hcd = usb_create_hcd(driver, &dev->dev, "au1xxx"); - if (!hcd) - return -ENOMEM; - hcd->rsrc_start = dev->resource[0].start; - hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1; - - if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { - pr_debug("request_mem_region failed\n"); - retval = -EBUSY; - goto err1; - } - - hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); - if (!hcd->regs) { - pr_debug("ioremap failed\n"); - retval = -ENOMEM; - goto err2; - } - - au1xxx_start_ohc(dev); - ohci_hcd_init(hcd_to_ohci(hcd)); - - retval = usb_add_hcd(hcd, dev->resource[1].start, IRQF_DISABLED | IRQF_SHARED); - if (retval == 0) - return retval; - - au1xxx_stop_ohc(dev); - iounmap(hcd->regs); - err2: - release_mem_region(hcd->rsrc_start, hcd->rsrc_len); - err1: - usb_put_hcd(hcd); - return retval; -} - - -/* may be called without controller electrically present */ -/* may be called with controller, bus, and devices active */ - -/** - * usb_hcd_au1xxx_remove - shutdown processing for Au1xxx-based HCDs - * @dev: USB Host Controller being removed - * Context: !in_interrupt() - * - * Reverses the effect of usb_hcd_au1xxx_probe(), first invoking - * the HCD's stop() method. It is always called from a thread - * context, normally "rmmod", "apmd", or something similar. - * - */ -static void usb_ohci_au1xxx_remove(struct usb_hcd *hcd, struct platform_device *dev) -{ - usb_remove_hcd(hcd); - au1xxx_stop_ohc(dev); - iounmap(hcd->regs); - release_mem_region(hcd->rsrc_start, hcd->rsrc_len); - usb_put_hcd(hcd); + /* Disable clock */ + au_writel(au_readl(USB_HOST_CONFIG) & ~USBH_ENABLE_CE, USB_HOST_CONFIG); + au_sync(); } -/*-------------------------------------------------------------------------*/ - -static int __devinit -ohci_au1xxx_start (struct usb_hcd *hcd) +static int __devinit ohci_au1xxx_start(struct usb_hcd *hcd) { - struct ohci_hcd *ohci = hcd_to_ohci (hcd); - int ret; + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + int ret; - ohci_dbg (ohci, "ohci_au1xxx_start, ohci:%p", ohci); + ohci_dbg(ohci, "ohci_au1xxx_start, ohci:%p", ohci); - if ((ret = ohci_init (ohci)) < 0) + if ((ret = ohci_init(ohci)) < 0) return ret; - if ((ret = ohci_run (ohci)) < 0) { + if ((ret = ohci_run(ohci)) < 0) { err ("can't start %s", hcd->self.bus_name); - ohci_stop (hcd); + ohci_stop(hcd); return ret; } return 0; } -/*-------------------------------------------------------------------------*/ - static const struct hc_driver ohci_au1xxx_hc_driver = { .description = hcd_name, .product_desc = "Au1xxx OHCI", @@ -296,18 +171,66 @@ static const struct hc_driver ohci_au1xxx_hc_driver = { .start_port_reset = ohci_start_port_reset, }; -/*-------------------------------------------------------------------------*/ - static int ohci_hcd_au1xxx_drv_probe(struct platform_device *pdev) { int ret; - - pr_debug ("In ohci_hcd_au1xxx_drv_probe"); + struct usb_hcd *hcd; if (usb_disabled()) return -ENODEV; - ret = usb_ohci_au1xxx_probe(&ohci_au1xxx_hc_driver, pdev); +#if defined(CONFIG_SOC_AU1200) && defined(CONFIG_DMA_COHERENT) + /* Au1200 AB USB does not support coherent memory */ + if (!(read_c0_prid() & 0xff)) { + printk(KERN_INFO "%s: this is chip revision AB !!\n", + pdev->name); + printk(KERN_INFO "%s: update your board or re-configure " + "the kernel\n", pdev->name); + return -ENODEV; + } +#endif + + if (pdev->resource[1].flags != IORESOURCE_IRQ) { + pr_debug("resource[1] is not IORESOURCE_IRQ\n"); + return -ENOMEM; + } + + hcd = usb_create_hcd(&ohci_au1xxx_hc_driver, &pdev->dev, "au1xxx"); + if (!hcd) + return -ENOMEM; + + hcd->rsrc_start = pdev->resource[0].start; + hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1; + + if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { + pr_debug("request_mem_region failed\n"); + ret = -EBUSY; + goto err1; + } + + hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len); + if (!hcd->regs) { + pr_debug("ioremap failed\n"); + ret = -ENOMEM; + goto err2; + } + + au1xxx_start_ohc(); + ohci_hcd_init(hcd_to_ohci(hcd)); + + ret = usb_add_hcd(hcd, pdev->resource[1].start, + IRQF_DISABLED | IRQF_SHARED); + if (ret == 0) { + platform_set_drvdata(pdev, hcd); + return ret; + } + + au1xxx_stop_ohc(); + iounmap(hcd->regs); +err2: + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); +err1: + usb_put_hcd(hcd); return ret; } @@ -315,30 +238,78 @@ static int ohci_hcd_au1xxx_drv_remove(struct platform_device *pdev) { struct usb_hcd *hcd = platform_get_drvdata(pdev); - usb_ohci_au1xxx_remove(hcd, pdev); + usb_remove_hcd(hcd); + au1xxx_stop_ohc(); + iounmap(hcd->regs); + release_mem_region(hcd->rsrc_start, hcd->rsrc_len); + usb_put_hcd(hcd); + platform_set_drvdata(pdev, NULL); + return 0; } - /*TBD*/ -/*static int ohci_hcd_au1xxx_drv_suspend(struct platform_device *dev) + +#ifdef CONFIG_PM +static int ohci_hcd_au1xxx_drv_suspend(struct platform_device *pdev, + pm_message_t message) { - struct usb_hcd *hcd = platform_get_drvdata(dev); + struct usb_hcd *hcd = platform_get_drvdata(pdev); + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + unsigned long flags; + int rc; + + rc = 0; + + /* Root hub was already suspended. Disable irq emission and + * mark HW unaccessible, bail out if RH has been resumed. Use + * the spinlock to properly synchronize with possible pending + * RH suspend or resume activity. + * + * This is still racy as hcd->state is manipulated outside of + * any locks =P But that will be a different fix. + */ + spin_lock_irqsave(&ohci->lock, flags); + if (hcd->state != HC_STATE_SUSPENDED) { + rc = -EINVAL; + goto bail; + } + ohci_writel(ohci, OHCI_INTR_MIE, &ohci->regs->intrdisable); + (void)ohci_readl(ohci, &ohci->regs->intrdisable); - return 0; + /* make sure snapshot being resumed re-enumerates everything */ + if (message.event == PM_EVENT_PRETHAW) + ohci_usb_reset(ohci); + + clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + + au1xxx_stop_ohc(); +bail: + spin_unlock_irqrestore(&ohci->lock, flags); + + return rc; } -static int ohci_hcd_au1xxx_drv_resume(struct platform_device *dev) + +static int ohci_hcd_au1xxx_drv_resume(struct platform_device *pdev) { - struct usb_hcd *hcd = platform_get_drvdata(dev); + struct usb_hcd *hcd = platform_get_drvdata(pdev); + + au1xxx_start_ohc(); + + set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + ohci_finish_controller_resume(hcd); return 0; } -*/ +#else +#define ohci_hcd_au1xxx_drv_suspend NULL +#define ohci_hcd_au1xxx_drv_resume NULL +#endif static struct platform_driver ohci_hcd_au1xxx_driver = { .probe = ohci_hcd_au1xxx_drv_probe, .remove = ohci_hcd_au1xxx_drv_remove, .shutdown = usb_hcd_platform_shutdown, - /*.suspend = ohci_hcd_au1xxx_drv_suspend, */ - /*.resume = ohci_hcd_au1xxx_drv_resume, */ + .suspend = ohci_hcd_au1xxx_drv_suspend, + .resume = ohci_hcd_au1xxx_drv_resume, .driver = { .name = "au1xxx-ohci", .owner = THIS_MODULE, diff --git a/drivers/usb/host/ohci-dbg.c b/drivers/usb/host/ohci-dbg.c index e06bfaebec5..7cef1d2f7cc 100644 --- a/drivers/usb/host/ohci-dbg.c +++ b/drivers/usb/host/ohci-dbg.c @@ -651,7 +651,7 @@ static ssize_t fill_registers_buffer(struct debug_buffer *buf) "%s\n" "%s version " DRIVER_VERSION "\n", hcd->self.controller->bus->name, - hcd->self.controller->bus_id, + dev_name(hcd->self.controller), hcd->product_desc, hcd_name); diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index a8160d65f32..26bc47941d0 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -974,7 +974,7 @@ MODULE_LICENSE ("GPL"); #define PCI_DRIVER ohci_pci_driver #endif -#ifdef CONFIG_SA1111 +#if defined(CONFIG_ARCH_SA1100) && defined(CONFIG_SA1111) #include "ohci-sa1111.c" #define SA1111_DRIVER ohci_hcd_sa1111_driver #endif diff --git a/drivers/usb/host/ohci-lh7a404.c b/drivers/usb/host/ohci-lh7a404.c index 13c12ed2225..1ef5d482c14 100644 --- a/drivers/usb/host/ohci-lh7a404.c +++ b/drivers/usb/host/ohci-lh7a404.c @@ -8,7 +8,7 @@ * Bus Glue for Sharp LH7A404 * * Written by Christopher Hoover <ch@hpl.hp.com> - * Based on fragments of previous driver by Rusell King et al. + * Based on fragments of previous driver by Russell King et al. * * Modified for LH7A404 from ohci-sa1111.c * by Durgesh Pattamatta <pattamattad@sharpsec.com> diff --git a/drivers/usb/host/ohci-omap.c b/drivers/usb/host/ohci-omap.c index 3a7c24c0367..6e5e5f81ac9 100644 --- a/drivers/usb/host/ohci-omap.c +++ b/drivers/usb/host/ohci-omap.c @@ -169,13 +169,16 @@ static void start_hnp(struct ohci_hcd *ohci) { const unsigned port = ohci_to_hcd(ohci)->self.otg_port - 1; unsigned long flags; + u32 l; otg_start_hnp(ohci->transceiver); local_irq_save(flags); ohci->transceiver->state = OTG_STATE_A_SUSPEND; writel (RH_PS_PSS, &ohci->regs->roothub.portstatus [port]); - OTG_CTRL_REG &= ~OTG_A_BUSREQ; + l = omap_readl(OTG_CTRL); + l &= ~OTG_A_BUSREQ; + omap_writel(l, OTG_CTRL); local_irq_restore(flags); } @@ -326,7 +329,7 @@ static int usb_hcd_omap_probe (const struct hc_driver *driver, } - hcd = usb_create_hcd (driver, &pdev->dev, pdev->dev.bus_id); + hcd = usb_create_hcd (driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { retval = -ENOMEM; goto err0; diff --git a/drivers/usb/host/ohci-pnx4008.c b/drivers/usb/host/ohci-pnx4008.c index 28b458f20cc..6ad8f2fc57b 100644 --- a/drivers/usb/host/ohci-pnx4008.c +++ b/drivers/usb/host/ohci-pnx4008.c @@ -109,8 +109,6 @@ static struct clk *usb_clk; static int isp1301_probe(struct i2c_adapter *adap); static int isp1301_detach(struct i2c_client *client); -static int isp1301_command(struct i2c_client *client, unsigned int cmd, - void *arg); static const unsigned short normal_i2c[] = { ISP1301_I2C_ADDR, ISP1301_I2C_ADDR + 1, I2C_CLIENT_END }; @@ -123,30 +121,37 @@ static struct i2c_client_address_data addr_data = { }; struct i2c_driver isp1301_driver = { - .class = I2C_CLASS_HWMON, + .driver = { + .name = "isp1301_pnx", + }, .attach_adapter = isp1301_probe, .detach_client = isp1301_detach, - .command = isp1301_command }; static int isp1301_attach(struct i2c_adapter *adap, int addr, int kind) { struct i2c_client *c; + int err; c = kzalloc(sizeof(*c), GFP_KERNEL); - if (!c) return -ENOMEM; - strcpy(c->name, "isp1301"); + strlcpy(c->name, "isp1301_pnx", I2C_NAME_SIZE); c->flags = 0; c->addr = addr; c->adapter = adap; c->driver = &isp1301_driver; + err = i2c_attach_client(c); + if (err) { + kfree(c); + return err; + } + isp1301_i2c_client = c; - return i2c_attach_client(c); + return 0; } static int isp1301_probe(struct i2c_adapter *adap) @@ -161,13 +166,6 @@ static int isp1301_detach(struct i2c_client *client) return 0; } -/* No commands defined */ -static int isp1301_command(struct i2c_client *client, unsigned int cmd, - void *arg) -{ - return 0; -} - static void i2c_write(u8 buf, u8 subaddr) { char tmpbuf[2]; @@ -389,7 +387,7 @@ static int __devinit usb_hcd_pnx4008_probe(struct platform_device *pdev) while ((__raw_readl(USB_OTG_CLK_STAT) & USB_CLOCK_MASK) != USB_CLOCK_MASK) ; - hcd = usb_create_hcd (driver, &pdev->dev, pdev->dev.bus_id); + hcd = usb_create_hcd (driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { err("Failed to allocate HC buffer"); ret = -ENOMEM; diff --git a/drivers/usb/host/ohci-ppc-of.c b/drivers/usb/host/ohci-ppc-of.c index a6725279122..91e6e101a4c 100644 --- a/drivers/usb/host/ohci-ppc-of.c +++ b/drivers/usb/host/ohci-ppc-of.c @@ -14,8 +14,8 @@ */ #include <linux/signal.h> +#include <linux/of_platform.h> -#include <asm/of_platform.h> #include <asm/prom.h> diff --git a/drivers/usb/host/ohci-ps3.c b/drivers/usb/host/ohci-ps3.c index c1935ae537f..55c95647f00 100644 --- a/drivers/usb/host/ohci-ps3.c +++ b/drivers/usb/host/ohci-ps3.c @@ -129,7 +129,7 @@ static int ps3_ohci_probe(struct ps3_system_bus_device *dev) dev->core.dma_mask = &dummy_mask; /* FIXME: for improper usb code */ - hcd = usb_create_hcd(&ps3_ohci_hc_driver, &dev->core, dev->core.bus_id); + hcd = usb_create_hcd(&ps3_ohci_hc_driver, &dev->core, dev_name(&dev->core)); if (!hcd) { dev_dbg(&dev->core, "%s:%d: usb_create_hcd failed\n", __func__, diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c index d4ee27d92be..127b1579902 100644 --- a/drivers/usb/host/ohci-pxa27x.c +++ b/drivers/usb/host/ohci-pxa27x.c @@ -27,6 +27,7 @@ #include <asm/mach-types.h> #include <asm/hardware.h> #include <asm/arch/pxa-regs.h> +#include <asm/arch/pxa2xx-regs.h> /* FIXME: for PSSR */ #include <asm/arch/ohci.h> #define PXA_UHC_MAX_PORTNUM 3 @@ -104,7 +105,7 @@ static int pxa27x_start_hc(struct device *dev) UHCHIE = (UHCHIE_UPRIE | UHCHIE_RWIE); /* Clear any OTG Pin Hold */ - if (PSSR & PSSR_OTGPH) + if (cpu_is_pxa27x() && (PSSR & PSSR_OTGPH)) PSSR |= PSSR_OTGPH; return 0; diff --git a/drivers/usb/host/ohci-q.c b/drivers/usb/host/ohci-q.c index 9b547407c93..6a9b4c55795 100644 --- a/drivers/usb/host/ohci-q.c +++ b/drivers/usb/host/ohci-q.c @@ -159,9 +159,6 @@ static int ed_schedule (struct ohci_hcd *ohci, struct ed *ed) { int branch; - if (ohci_to_hcd(ohci)->state == HC_STATE_QUIESCING) - return -EAGAIN; - ed->state = ED_OPER; ed->ed_prev = NULL; ed->ed_next = NULL; diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c index ead4772f0f2..3c7a740cfe0 100644 --- a/drivers/usb/host/ohci-s3c2410.c +++ b/drivers/usb/host/ohci-s3c2410.c @@ -8,7 +8,7 @@ * USB Bus Glue for Samsung S3C2410 * * Written by Christopher Hoover <ch@hpl.hp.com> - * Based on fragments of previous driver by Rusell King et al. + * Based on fragments of previous driver by Russell King et al. * * Modified for S3C2410 from ohci-sa1111.c, ohci-omap.c and ohci-lh7a40.c * by Ben Dooks, <ben@simtec.co.uk> diff --git a/drivers/usb/host/ohci-sa1111.c b/drivers/usb/host/ohci-sa1111.c index 0f48f2d9922..2e9dceb9bb9 100644 --- a/drivers/usb/host/ohci-sa1111.c +++ b/drivers/usb/host/ohci-sa1111.c @@ -8,7 +8,7 @@ * SA1111 Bus Glue * * Written by Christopher Hoover <ch@hpl.hp.com> - * Based on fragments of previous driver by Rusell King et al. + * Based on fragments of previous driver by Russell King et al. * * This file is licenced under the GPL. */ diff --git a/drivers/usb/host/ohci-sm501.c b/drivers/usb/host/ohci-sm501.c index e610698c6b6..21b164e4abe 100644 --- a/drivers/usb/host/ohci-sm501.c +++ b/drivers/usb/host/ohci-sm501.c @@ -143,7 +143,7 @@ static int ohci_hcd_sm501_drv_probe(struct platform_device *pdev) goto err2; } - hcd = usb_create_hcd(driver, &pdev->dev, pdev->dev.bus_id); + hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { retval = -ENOMEM; goto err2; diff --git a/drivers/usb/host/ohci-ssb.c b/drivers/usb/host/ohci-ssb.c index 7275186db31..3660c83d80a 100644 --- a/drivers/usb/host/ohci-ssb.c +++ b/drivers/usb/host/ohci-ssb.c @@ -113,7 +113,7 @@ static int ssb_ohci_attach(struct ssb_device *dev) ssb_device_enable(dev, flags); hcd = usb_create_hcd(&ssb_ohci_hc_driver, dev->dev, - dev->dev->bus_id); + dev_name(dev->dev)); if (!hcd) goto err_dev_disable; ohcidev = hcd_to_ssb_ohci(hcd); diff --git a/drivers/usb/host/r8a66597-hcd.c b/drivers/usb/host/r8a66597-hcd.c index 16667342b3c..d5f02dddb12 100644 --- a/drivers/usb/host/r8a66597-hcd.c +++ b/drivers/usb/host/r8a66597-hcd.c @@ -312,9 +312,9 @@ static void put_child_connect_map(struct r8a66597 *r8a66597, int address) static void set_pipe_reg_addr(struct r8a66597_pipe *pipe, u8 dma_ch) { u16 pipenum = pipe->info.pipenum; - unsigned long fifoaddr[] = {D0FIFO, D1FIFO, CFIFO}; - unsigned long fifosel[] = {D0FIFOSEL, D1FIFOSEL, CFIFOSEL}; - unsigned long fifoctr[] = {D0FIFOCTR, D1FIFOCTR, CFIFOCTR}; + const unsigned long fifoaddr[] = {D0FIFO, D1FIFO, CFIFO}; + const unsigned long fifosel[] = {D0FIFOSEL, D1FIFOSEL, CFIFOSEL}; + const unsigned long fifoctr[] = {D0FIFOCTR, D1FIFOCTR, CFIFOCTR}; if (dma_ch > R8A66597_PIPE_NO_DMA) /* dma fifo not use? */ dma_ch = R8A66597_PIPE_NO_DMA; @@ -863,6 +863,32 @@ static void disable_r8a66597_pipe_all(struct r8a66597 *r8a66597, dev->dma_map = 0; } +static u16 get_interval(struct urb *urb, __u8 interval) +{ + u16 time = 1; + int i; + + if (urb->dev->speed == USB_SPEED_HIGH) { + if (interval > IITV) + time = IITV; + else + time = interval ? interval - 1 : 0; + } else { + if (interval > 128) { + time = IITV; + } else { + /* calculate the nearest value for PIPEPERI */ + for (i = 0; i < 7; i++) { + if ((1 << i) < interval && + (1 << (i + 1) > interval)) + time = 1 << i; + } + } + } + + return time; +} + static unsigned long get_timer_interval(struct urb *urb, __u8 interval) { __u8 i; @@ -901,10 +927,7 @@ static void init_pipe_info(struct r8a66597 *r8a66597, struct urb *urb, info.interval = 0; info.timer_interval = 0; } else { - if (ep->bInterval > IITV) - info.interval = IITV; - else - info.interval = ep->bInterval ? ep->bInterval - 1 : 0; + info.interval = get_interval(urb, ep->bInterval); info.timer_interval = get_timer_interval(urb, ep->bInterval); } if (ep->bEndpointAddress & USB_ENDPOINT_DIR_MASK) @@ -2244,6 +2267,7 @@ static int __init r8a66597_probe(struct platform_device *pdev) struct r8a66597 *r8a66597; int ret = 0; int i; + unsigned long irq_trigger; if (pdev->dev.dma_mask) { ret = -EINVAL; @@ -2302,7 +2326,11 @@ static int __init r8a66597_probe(struct platform_device *pdev) INIT_LIST_HEAD(&r8a66597->child_device); hcd->rsrc_start = res->start; - ret = usb_add_hcd(hcd, irq, IRQF_DISABLED); + if (irq_sense == INTL) + irq_trigger = IRQF_TRIGGER_LOW; + else + irq_trigger = IRQF_TRIGGER_FALLING; + ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | irq_trigger); if (ret != 0) { err("Failed to add hcd"); goto clean_up; diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c index 426575247b2..340d72da554 100644 --- a/drivers/usb/host/sl811-hcd.c +++ b/drivers/usb/host/sl811-hcd.c @@ -1674,7 +1674,7 @@ sl811h_probe(struct platform_device *dev) } /* allocate and initialize hcd */ - hcd = usb_create_hcd(&sl811h_hc_driver, &dev->dev, dev->dev.bus_id); + hcd = usb_create_hcd(&sl811h_hc_driver, &dev->dev, dev_name(&dev->dev)); if (!hcd) { retval = -ENOMEM; goto err5; diff --git a/drivers/usb/host/u132-hcd.c b/drivers/usb/host/u132-hcd.c index 9b6323f768b..20ad3c48fcb 100644 --- a/drivers/usb/host/u132-hcd.c +++ b/drivers/usb/host/u132-hcd.c @@ -3124,7 +3124,7 @@ static int __devinit u132_probe(struct platform_device *pdev) if (pdev->dev.dma_mask) return -EINVAL; - hcd = usb_create_hcd(&u132_hc_driver, &pdev->dev, pdev->dev.bus_id); + hcd = usb_create_hcd(&u132_hc_driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { printk(KERN_ERR "failed to create the usb hcd struct for U132\n" ); diff --git a/drivers/usb/host/uhci-hub.c b/drivers/usb/host/uhci-hub.c index 8e4427aebb1..885b585360b 100644 --- a/drivers/usb/host/uhci-hub.c +++ b/drivers/usb/host/uhci-hub.c @@ -12,7 +12,7 @@ * (C) Copyright 2004 Alan Stern, stern@rowland.harvard.edu */ -static __u8 root_hub_hub_des[] = +static const __u8 root_hub_hub_des[] = { 0x09, /* __u8 bLength; */ 0x29, /* __u8 bDescriptorType; Hub-descriptor */ |