diff options
Diffstat (limited to 'drivers/usb/host')
-rw-r--r-- | drivers/usb/host/Makefile | 4 | ||||
-rw-r--r-- | drivers/usb/host/ehci-hcd.c | 9 | ||||
-rw-r--r-- | drivers/usb/host/ehci-hub.c | 4 | ||||
-rw-r--r-- | drivers/usb/host/ehci-pci.c | 20 | ||||
-rw-r--r-- | drivers/usb/host/ehci-q.c | 14 | ||||
-rw-r--r-- | drivers/usb/host/hc_crisv10.c | 2 | ||||
-rw-r--r-- | drivers/usb/host/isp116x-hcd.c | 422 | ||||
-rw-r--r-- | drivers/usb/host/isp116x.h | 83 | ||||
-rw-r--r-- | drivers/usb/host/ohci-hcd.c | 14 | ||||
-rw-r--r-- | drivers/usb/host/ohci-hub.c | 2 | ||||
-rw-r--r-- | drivers/usb/host/ohci-pxa27x.c | 121 | ||||
-rw-r--r-- | drivers/usb/host/pci-quirks.c | 6 | ||||
-rw-r--r-- | drivers/usb/host/sl811-hcd.c | 14 | ||||
-rw-r--r-- | drivers/usb/host/sl811_cs.c | 115 | ||||
-rw-r--r-- | drivers/usb/host/uhci-debug.c | 14 | ||||
-rw-r--r-- | drivers/usb/host/uhci-hcd.c | 34 | ||||
-rw-r--r-- | drivers/usb/host/uhci-hcd.h | 32 | ||||
-rw-r--r-- | drivers/usb/host/uhci-q.c | 30 |
18 files changed, 420 insertions, 520 deletions
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile index 58321d3f314..e3020f4b17b 100644 --- a/drivers/usb/host/Makefile +++ b/drivers/usb/host/Makefile @@ -2,6 +2,10 @@ # Makefile for USB Host Controller Drivers # +ifeq ($(CONFIG_USB_DEBUG),y) + EXTRA_CFLAGS += -DDEBUG +endif + obj-$(CONFIG_PCI) += pci-quirks.o obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 29f52a44b92..9dd3d14c64f 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -17,13 +17,6 @@ */ #include <linux/config.h> - -#ifdef CONFIG_USB_DEBUG - #define DEBUG -#else - #undef DEBUG -#endif - #include <linux/module.h> #include <linux/pci.h> #include <linux/dmapool.h> @@ -624,7 +617,7 @@ static irqreturn_t ehci_irq (struct usb_hcd *hcd, struct pt_regs *regs) } /* remote wakeup [4.3.1] */ - if ((status & STS_PCD) && hcd->remote_wakeup) { + if (status & STS_PCD) { unsigned i = HCS_N_PORTS (ehci->hcs_params); /* resume root hub? */ diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index 82caf336e9b..69b0b9be7a6 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -59,7 +59,7 @@ static int ehci_bus_suspend (struct usb_hcd *hcd) if ((t1 & PORT_PE) && !(t1 & PORT_OWNER)) t2 |= PORT_SUSPEND; - if (hcd->remote_wakeup) + if (device_may_wakeup(&hcd->self.root_hub->dev)) t2 |= PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E; else t2 &= ~(PORT_WKOC_E|PORT_WKDISC_E|PORT_WKCONN_E); @@ -517,7 +517,7 @@ static int ehci_hub_control ( if ((temp & PORT_PE) == 0 || (temp & PORT_RESET) != 0) goto error; - if (hcd->remote_wakeup) + if (device_may_wakeup(&hcd->self.root_hub->dev)) temp |= PORT_WAKE_BITS; writel (temp | PORT_SUSPEND, &ehci->regs->port_status [wIndex]); diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 13f73a836e4..08ca0f849da 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -210,7 +210,16 @@ static int ehci_pci_setup(struct usb_hcd *hcd) /* Serial Bus Release Number is at PCI 0x60 offset */ pci_read_config_byte(pdev, 0x60, &ehci->sbrn); - /* REVISIT: per-port wake capability (PCI 0x62) currently unused */ + /* Workaround current PCI init glitch: wakeup bits aren't + * being set from PCI PM capability. + */ + if (!device_can_wakeup(&pdev->dev)) { + u16 port_wake; + + pci_read_config_word(pdev, 0x62, &port_wake); + if (port_wake & 0x0001) + device_init_wakeup(&pdev->dev, 1); + } retval = ehci_pci_reinit(ehci, pdev); done: @@ -269,7 +278,6 @@ static int ehci_pci_resume(struct usb_hcd *hcd) { struct ehci_hcd *ehci = hcd_to_ehci(hcd); unsigned port; - struct usb_device *root = hcd->self.root_hub; struct pci_dev *pdev = to_pci_dev(hcd->self.controller); int retval = -EINVAL; @@ -303,13 +311,7 @@ static int ehci_pci_resume(struct usb_hcd *hcd) restart: ehci_dbg(ehci, "lost power, restarting\n"); - for (port = HCS_N_PORTS(ehci->hcs_params); port > 0; ) { - port--; - if (!root->children [port]) - continue; - usb_set_device_state(root->children[port], - USB_STATE_NOTATTACHED); - } + usb_root_hub_lost_power(hcd->self.root_hub); /* Else reset, to cope with power loss or flush-to-storage * style "resume" having let BIOS kick in during reboot. diff --git a/drivers/usb/host/ehci-q.c b/drivers/usb/host/ehci-q.c index bf03ec0d8ee..9b13bf2fa98 100644 --- a/drivers/usb/host/ehci-q.c +++ b/drivers/usb/host/ehci-q.c @@ -514,18 +514,18 @@ qh_urb_transaction ( qtd->urb = urb; qtd_prev->hw_next = QTD_NEXT (qtd->qtd_dma); list_add_tail (&qtd->qtd_list, head); + + /* for zero length DATA stages, STATUS is always IN */ + if (len == 0) + token |= (1 /* "in" */ << 8); } /* * data transfer stage: buffer setup */ - if (likely (len > 0)) - buf = urb->transfer_dma; - else - buf = 0; + buf = urb->transfer_dma; - /* for zero length DATA stages, STATUS is always IN */ - if (!buf || is_input) + if (is_input) token |= (1 /* "in" */ << 8); /* else it's already initted to "out" pid (0 << 8) */ @@ -572,7 +572,7 @@ qh_urb_transaction ( * control requests may need a terminating data "status" ack; * bulk ones may need a terminating short packet (zero length). */ - if (likely (buf != 0)) { + if (likely (urb->transfer_buffer_length != 0)) { int one_more = 0; if (usb_pipecontrol (urb->pipe)) { diff --git a/drivers/usb/host/hc_crisv10.c b/drivers/usb/host/hc_crisv10.c index 0eaabeb37ac..641268d7e6f 100644 --- a/drivers/usb/host/hc_crisv10.c +++ b/drivers/usb/host/hc_crisv10.c @@ -4397,7 +4397,7 @@ static int __init etrax_usb_hc_init(void) device_initialize(&fake_device); kobject_set_name(&fake_device.kobj, "etrax_usb"); kobject_add(&fake_device.kobj); - kobject_hotplug(&fake_device.kobj, KOBJ_ADD); + kobject_uevent(&fake_device.kobj, KOBJ_ADD); hc->bus->controller = &fake_device; usb_register_bus(hc->bus); diff --git a/drivers/usb/host/isp116x-hcd.c b/drivers/usb/host/isp116x-hcd.c index 82f64986bc2..584b8dc6511 100644 --- a/drivers/usb/host/isp116x-hcd.c +++ b/drivers/usb/host/isp116x-hcd.c @@ -55,19 +55,13 @@ /* enqueuing/finishing log of urbs */ //#define URB_TRACE -#include <linux/config.h> #include <linux/module.h> -#include <linux/moduleparam.h> -#include <linux/kernel.h> #include <linux/delay.h> -#include <linux/ioport.h> -#include <linux/sched.h> -#include <linux/slab.h> -#include <linux/smp_lock.h> +#include <linux/debugfs.h> +#include <linux/seq_file.h> #include <linux/errno.h> #include <linux/init.h> #include <linux/list.h> -#include <linux/interrupt.h> #include <linux/usb.h> #include <linux/usb_isp116x.h> #include <linux/platform_device.h> @@ -77,14 +71,10 @@ #include <asm/system.h> #include <asm/byteorder.h> -#ifndef DEBUG -# define STUB_DEBUG_FILE -#endif - #include "../core/hcd.h" #include "isp116x.h" -#define DRIVER_VERSION "05 Aug 2005" +#define DRIVER_VERSION "03 Nov 2005" #define DRIVER_DESC "ISP116x USB Host Controller Driver" MODULE_DESCRIPTION(DRIVER_DESC); @@ -164,13 +154,11 @@ static void pack_fifo(struct isp116x *isp116x) struct ptd *ptd; int buflen = isp116x->atl_last_dir == PTD_DIR_IN ? isp116x->atl_bufshrt : isp116x->atl_buflen; - int ptd_count = 0; isp116x_write_reg16(isp116x, HCuPINT, HCuPINT_AIIEOT); isp116x_write_reg16(isp116x, HCXFERCTR, buflen); isp116x_write_addr(isp116x, HCATLPORT | ISP116x_WRITE_OFFSET); for (ep = isp116x->atl_active; ep; ep = ep->active) { - ++ptd_count; ptd = &ep->ptd; dump_ptd(ptd); dump_ptd_out_data(ptd, ep->data); @@ -305,9 +293,8 @@ static void postproc_atl_queue(struct isp116x *isp116x) udev = urb->dev; ptd = &ep->ptd; cc = PTD_GET_CC(ptd); - - spin_lock(&urb->lock); short_not_ok = 1; + spin_lock(&urb->lock); /* Data underrun is special. For allowed underrun we clear the error and continue as normal. For @@ -420,7 +407,7 @@ static void postproc_atl_queue(struct isp116x *isp116x) ep->nextpid = 0; break; default: - BUG_ON(1); + BUG(); } spin_unlock(&urb->lock); } @@ -628,8 +615,12 @@ static irqreturn_t isp116x_irq(struct usb_hcd *hcd, struct pt_regs *regs) u32 intstat = isp116x_read_reg32(isp116x, HCINTSTAT); isp116x_write_reg32(isp116x, HCINTSTAT, intstat); if (intstat & HCINT_UE) { - ERR("Unrecoverable error\n"); - /* What should we do here? Reset? */ + ERR("Unrecoverable error, HC is dead!\n"); + /* IRQ's are off, we do no DMA, + perfectly ready to die ... */ + hcd->state = HC_STATE_HALT; + ret = IRQ_HANDLED; + goto done; } if (intstat & HCINT_RHSC) /* When root hub or any of its ports is going @@ -640,7 +631,6 @@ static irqreturn_t isp116x_irq(struct usb_hcd *hcd, struct pt_regs *regs) if (intstat & HCINT_RD) { DBG("---- remote wakeup\n"); usb_hcd_resume_root_hub(hcd); - ret = IRQ_HANDLED; } irqstat &= ~HCuPINT_OPR; ret = IRQ_HANDLED; @@ -651,6 +641,7 @@ static irqreturn_t isp116x_irq(struct usb_hcd *hcd, struct pt_regs *regs) } isp116x_write_reg16(isp116x, HCuPINTENB, isp116x->irqenb); + done: spin_unlock(&isp116x->lock); return ret; } @@ -724,6 +715,7 @@ static int isp116x_urb_enqueue(struct usb_hcd *hcd, spin_lock_irqsave(&isp116x->lock, flags); if (!HC_IS_RUNNING(hcd->state)) { + kfree(ep); ret = -ENODEV; goto fail; } @@ -888,7 +880,7 @@ static void isp116x_endpoint_disable(struct usb_hcd *hcd, struct usb_host_endpoint *hep) { int i; - struct isp116x_ep *ep = hep->hcpriv;; + struct isp116x_ep *ep = hep->hcpriv; if (!ep) return; @@ -916,8 +908,6 @@ static int isp116x_get_frame(struct usb_hcd *hcd) return (int)fmnum; } -/*----------------------------------------------------------------*/ - /* Adapted from ohci-hub.c. Currently we don't support autosuspend. */ @@ -968,11 +958,10 @@ static void isp116x_hub_descriptor(struct isp116x *isp116x, desc->bHubContrCurrent = 0; desc->bNbrPorts = (u8) (reg & 0x3); /* Power switching, device type, overcurrent. */ - desc->wHubCharacteristics = - (__force __u16) cpu_to_le16((u16) ((reg >> 8) & 0x1f)); + desc->wHubCharacteristics = cpu_to_le16((u16) ((reg >> 8) & 0x1f)); desc->bPwrOn2PwrGood = (u8) ((reg >> 24) & 0xff); /* two bitmaps: ports removable, and legacy PortPwrCtrlMask */ - desc->bitmap[0] = desc->bNbrPorts == 1 ? 1 << 1 : 3 << 1; + desc->bitmap[0] = 0; desc->bitmap[1] = ~0; } @@ -1159,135 +1148,9 @@ static int isp116x_hub_control(struct usb_hcd *hcd, return ret; } -#ifdef CONFIG_PM - -static int isp116x_bus_suspend(struct usb_hcd *hcd) -{ - struct isp116x *isp116x = hcd_to_isp116x(hcd); - unsigned long flags; - u32 val; - int ret = 0; - - spin_lock_irqsave(&isp116x->lock, flags); - - val = isp116x_read_reg32(isp116x, HCCONTROL); - switch (val & HCCONTROL_HCFS) { - case HCCONTROL_USB_OPER: - hcd->state = HC_STATE_QUIESCING; - val &= (~HCCONTROL_HCFS & ~HCCONTROL_RWE); - val |= HCCONTROL_USB_SUSPEND; - if (hcd->remote_wakeup) - val |= HCCONTROL_RWE; - /* Wait for usb transfers to finish */ - mdelay(2); - isp116x_write_reg32(isp116x, HCCONTROL, val); - hcd->state = HC_STATE_SUSPENDED; - /* Wait for devices to suspend */ - mdelay(5); - case HCCONTROL_USB_SUSPEND: - break; - case HCCONTROL_USB_RESUME: - isp116x_write_reg32(isp116x, HCCONTROL, - (val & ~HCCONTROL_HCFS) | - HCCONTROL_USB_RESET); - case HCCONTROL_USB_RESET: - ret = -EBUSY; - break; - default: - ret = -EINVAL; - } - - spin_unlock_irqrestore(&isp116x->lock, flags); - return ret; -} - -static int isp116x_bus_resume(struct usb_hcd *hcd) -{ - struct isp116x *isp116x = hcd_to_isp116x(hcd); - u32 val; - int ret = -EINPROGRESS; - - msleep(5); - spin_lock_irq(&isp116x->lock); - - val = isp116x_read_reg32(isp116x, HCCONTROL); - switch (val & HCCONTROL_HCFS) { - case HCCONTROL_USB_SUSPEND: - val &= ~HCCONTROL_HCFS; - val |= HCCONTROL_USB_RESUME; - isp116x_write_reg32(isp116x, HCCONTROL, val); - case HCCONTROL_USB_RESUME: - break; - case HCCONTROL_USB_OPER: - /* Without setting power_state here the - SUSPENDED state won't be removed from - sysfs/usbN/power.state as a response to remote - wakeup. Maybe in the future. */ - hcd->self.root_hub->dev.power.power_state = PMSG_ON; - ret = 0; - break; - default: - ret = -EBUSY; - } - - if (ret != -EINPROGRESS) { - spin_unlock_irq(&isp116x->lock); - return ret; - } - - val = isp116x->rhdesca & RH_A_NDP; - while (val--) { - u32 stat = - isp116x_read_reg32(isp116x, val ? HCRHPORT2 : HCRHPORT1); - /* force global, not selective, resume */ - if (!(stat & RH_PS_PSS)) - continue; - DBG("%s: Resuming port %d\n", __func__, val); - isp116x_write_reg32(isp116x, RH_PS_POCI, val - ? HCRHPORT2 : HCRHPORT1); - } - spin_unlock_irq(&isp116x->lock); - - hcd->state = HC_STATE_RESUMING; - mdelay(20); - - /* Go operational */ - spin_lock_irq(&isp116x->lock); - val = isp116x_read_reg32(isp116x, HCCONTROL); - isp116x_write_reg32(isp116x, HCCONTROL, - (val & ~HCCONTROL_HCFS) | HCCONTROL_USB_OPER); - spin_unlock_irq(&isp116x->lock); - /* see analogous comment above */ - hcd->self.root_hub->dev.power.power_state = PMSG_ON; - hcd->state = HC_STATE_RUNNING; - - return 0; -} - - -#else - -#define isp116x_bus_suspend NULL -#define isp116x_bus_resume NULL - -#endif - /*-----------------------------------------------------------------*/ -#ifdef STUB_DEBUG_FILE - -static inline void create_debug_file(struct isp116x *isp116x) -{ -} - -static inline void remove_debug_file(struct isp116x *isp116x) -{ -} - -#else - -#include <linux/proc_fs.h> -#include <linux/seq_file.h> +#ifdef CONFIG_DEBUG_FS static void dump_irq(struct seq_file *s, char *label, u16 mask) { @@ -1311,13 +1174,9 @@ static void dump_int(struct seq_file *s, char *label, u32 mask) mask & HCINT_SF ? " sof" : "", mask & HCINT_SO ? " so" : ""); } -static int proc_isp116x_show(struct seq_file *s, void *unused) +static int isp116x_show_dbg(struct seq_file *s, void *unused) { struct isp116x *isp116x = s->private; - struct isp116x_ep *ep; - struct urb *urb; - unsigned i; - char *str; seq_printf(s, "%s\n%s version %s\n", isp116x_to_hcd(isp116x)->product_desc, hcd_name, @@ -1333,105 +1192,50 @@ static int proc_isp116x_show(struct seq_file *s, void *unused) } spin_lock_irq(&isp116x->lock); - dump_irq(s, "hc_irq_enable", isp116x_read_reg16(isp116x, HCuPINTENB)); dump_irq(s, "hc_irq_status", isp116x_read_reg16(isp116x, HCuPINT)); dump_int(s, "hc_int_enable", isp116x_read_reg32(isp116x, HCINTENB)); dump_int(s, "hc_int_status", isp116x_read_reg32(isp116x, HCINTSTAT)); - - list_for_each_entry(ep, &isp116x->async, schedule) { - - switch (ep->nextpid) { - case USB_PID_IN: - str = "in"; - break; - case USB_PID_OUT: - str = "out"; - break; - case USB_PID_SETUP: - str = "setup"; - break; - case USB_PID_ACK: - str = "status"; - break; - default: - str = "?"; - break; - }; - seq_printf(s, "%p, ep%d%s, maxpacket %d:\n", ep, - ep->epnum, str, ep->maxpacket); - list_for_each_entry(urb, &ep->hep->urb_list, urb_list) { - seq_printf(s, " urb%p, %d/%d\n", urb, - urb->actual_length, - urb->transfer_buffer_length); - } - } - if (!list_empty(&isp116x->async)) - seq_printf(s, "\n"); - - seq_printf(s, "periodic size= %d\n", PERIODIC_SIZE); - - for (i = 0; i < PERIODIC_SIZE; i++) { - ep = isp116x->periodic[i]; - if (!ep) - continue; - seq_printf(s, "%2d [%3d]:\n", i, isp116x->load[i]); - - /* DUMB: prints shared entries multiple times */ - do { - seq_printf(s, " %d/%p (%sdev%d ep%d%s max %d)\n", - ep->period, ep, - (ep->udev->speed == - USB_SPEED_FULL) ? "" : "ls ", - ep->udev->devnum, ep->epnum, - (ep->epnum == - 0) ? "" : ((ep->nextpid == - USB_PID_IN) ? "in" : "out"), - ep->maxpacket); - ep = ep->next; - } while (ep); - } + isp116x_show_regs_seq(isp116x, s); spin_unlock_irq(&isp116x->lock); seq_printf(s, "\n"); return 0; } -static int proc_isp116x_open(struct inode *inode, struct file *file) +static int isp116x_open_seq(struct inode *inode, struct file *file) { - return single_open(file, proc_isp116x_show, PDE(inode)->data); + return single_open(file, isp116x_show_dbg, inode->u.generic_ip); } -static struct file_operations proc_ops = { - .open = proc_isp116x_open, +static struct file_operations isp116x_debug_fops = { + .open = isp116x_open_seq, .read = seq_read, .llseek = seq_lseek, .release = single_release, }; -/* expect just one isp116x per system */ -static const char proc_filename[] = "driver/isp116x"; - -static void create_debug_file(struct isp116x *isp116x) +static int create_debug_file(struct isp116x *isp116x) { - struct proc_dir_entry *pde; - - pde = create_proc_entry(proc_filename, 0, NULL); - if (pde == NULL) - return; - - pde->proc_fops = &proc_ops; - pde->data = isp116x; - isp116x->pde = pde; + isp116x->dentry = debugfs_create_file(hcd_name, + S_IRUGO, NULL, isp116x, + &isp116x_debug_fops); + if (!isp116x->dentry) + return -ENOMEM; + return 0; } static void remove_debug_file(struct isp116x *isp116x) { - if (isp116x->pde) - remove_proc_entry(proc_filename, NULL); + debugfs_remove(isp116x->dentry); } -#endif +#else + +#define create_debug_file(d) 0 +#define remove_debug_file(d) do{}while(0) + +#endif /* CONFIG_DEBUG_FS */ /*-----------------------------------------------------------------*/ @@ -1466,7 +1270,7 @@ static int isp116x_reset(struct usb_hcd *hcd) struct isp116x *isp116x = hcd_to_isp116x(hcd); unsigned long t; u16 clkrdy = 0; - int ret = 0, timeout = 15 /* ms */ ; + int ret, timeout = 15 /* ms */ ; ret = isp116x_sw_reset(isp116x); if (ret) @@ -1482,7 +1286,7 @@ static int isp116x_reset(struct usb_hcd *hcd) break; } if (!clkrdy) { - ERR("Clock not ready after 20ms\n"); + ERR("Clock not ready after %dms\n", timeout); /* After sw_reset the clock won't report to be ready, if H_WAKEUP pin is high. */ ERR("Please make sure that the H_WAKEUP pin is pulled low!\n"); @@ -1572,7 +1376,8 @@ static int isp116x_start(struct usb_hcd *hcd) val = 0; if (board->remote_wakeup_enable) { - hcd->can_wakeup = 1; + if (!device_can_wakeup(hcd->self.controller)) + device_init_wakeup(hcd->self.controller, 1); val |= RH_HS_DRWE; } isp116x_write_reg32(isp116x, HCRHSTATUS, val); @@ -1600,12 +1405,126 @@ static int isp116x_start(struct usb_hcd *hcd) isp116x_write_reg32(isp116x, HCRHPORT1, RH_PS_CCS); isp116x_write_reg32(isp116x, HCRHPORT2, RH_PS_CCS); - isp116x_show_regs(isp116x); + isp116x_show_regs_log(isp116x); spin_unlock_irqrestore(&isp116x->lock, flags); return 0; } -/*-----------------------------------------------------------------*/ +#ifdef CONFIG_PM + +static int isp116x_bus_suspend(struct usb_hcd *hcd) +{ + struct isp116x *isp116x = hcd_to_isp116x(hcd); + unsigned long flags; + u32 val; + int ret = 0; + + spin_lock_irqsave(&isp116x->lock, flags); + + val = isp116x_read_reg32(isp116x, HCCONTROL); + switch (val & HCCONTROL_HCFS) { + case HCCONTROL_USB_OPER: + val &= (~HCCONTROL_HCFS & ~HCCONTROL_RWE); + val |= HCCONTROL_USB_SUSPEND; + if (device_may_wakeup(&hcd->self.root_hub->dev)) + val |= HCCONTROL_RWE; + /* Wait for usb transfers to finish */ + mdelay(2); + isp116x_write_reg32(isp116x, HCCONTROL, val); + /* Wait for devices to suspend */ + mdelay(5); + case HCCONTROL_USB_SUSPEND: + break; + case HCCONTROL_USB_RESUME: + isp116x_write_reg32(isp116x, HCCONTROL, + (val & ~HCCONTROL_HCFS) | + HCCONTROL_USB_RESET); + case HCCONTROL_USB_RESET: + ret = -EBUSY; + break; + default: + ret = -EINVAL; + } + + spin_unlock_irqrestore(&isp116x->lock, flags); + return ret; +} + +static int isp116x_bus_resume(struct usb_hcd *hcd) +{ + struct isp116x *isp116x = hcd_to_isp116x(hcd); + u32 val; + + msleep(5); + spin_lock_irq(&isp116x->lock); + + val = isp116x_read_reg32(isp116x, HCCONTROL); + switch (val & HCCONTROL_HCFS) { + case HCCONTROL_USB_SUSPEND: + val &= ~HCCONTROL_HCFS; + val |= HCCONTROL_USB_RESUME; + isp116x_write_reg32(isp116x, HCCONTROL, val); + case HCCONTROL_USB_RESUME: + break; + case HCCONTROL_USB_OPER: + spin_unlock_irq(&isp116x->lock); + /* Without setting power_state here the + SUSPENDED state won't be removed from + sysfs/usbN/power.state as a response to remote + wakeup. Maybe in the future. */ + hcd->self.root_hub->dev.power.power_state = PMSG_ON; + return 0; + default: + /* HCCONTROL_USB_RESET: this may happen, when during + suspension the HC lost power. Reinitialize completely */ + spin_unlock_irq(&isp116x->lock); + DBG("Chip has been reset while suspended. Reinit from scratch.\n"); + isp116x_reset(hcd); + isp116x_start(hcd); + isp116x_hub_control(hcd, SetPortFeature, + USB_PORT_FEAT_POWER, 1, NULL, 0); + if ((isp116x->rhdesca & RH_A_NDP) == 2) + isp116x_hub_control(hcd, SetPortFeature, + USB_PORT_FEAT_POWER, 2, NULL, 0); + hcd->self.root_hub->dev.power.power_state = PMSG_ON; + return 0; + } + + val = isp116x->rhdesca & RH_A_NDP; + while (val--) { + u32 stat = + isp116x_read_reg32(isp116x, val ? HCRHPORT2 : HCRHPORT1); + /* force global, not selective, resume */ + if (!(stat & RH_PS_PSS)) + continue; + DBG("%s: Resuming port %d\n", __func__, val); + isp116x_write_reg32(isp116x, RH_PS_POCI, val + ? HCRHPORT2 : HCRHPORT1); + } + spin_unlock_irq(&isp116x->lock); + + hcd->state = HC_STATE_RESUMING; + msleep(20); + + /* Go operational */ + spin_lock_irq(&isp116x->lock); + val = isp116x_read_reg32(isp116x, HCCONTROL); + isp116x_write_reg32(isp116x, HCCONTROL, + (val & ~HCCONTROL_HCFS) | HCCONTROL_USB_OPER); + spin_unlock_irq(&isp116x->lock); + /* see analogous comment above */ + hcd->self.root_hub->dev.power.power_state = PMSG_ON; + hcd->state = HC_STATE_RUNNING; + + return 0; +} + +#else + +#define isp116x_bus_suspend NULL +#define isp116x_bus_resume NULL + +#endif static struct hc_driver isp116x_hc_driver = { .description = hcd_name, @@ -1735,12 +1654,19 @@ static int __init isp116x_probe(struct platform_device *pdev) } ret = usb_add_hcd(hcd, irq, SA_INTERRUPT); - if (ret != 0) + if (ret) goto err6; - create_debug_file(isp116x); + ret = create_debug_file(isp116x); + if (ret) { + ERR("Couldn't create debugfs entry\n"); + goto err7; + } + return 0; + err7: + usb_remove_hcd(hcd); err6: usb_put_hcd(hcd); err5: @@ -1762,13 +1688,9 @@ static int __init isp116x_probe(struct platform_device *pdev) */ static int isp116x_suspend(struct platform_device *dev, pm_message_t state) { - int ret = 0; - - VDBG("%s: state %x\n", __func__, state); - + VDBG("%s: state %x\n", __func__, state.event); dev->dev.power.power_state = state; - - return ret; + return 0; } /* @@ -1776,13 +1698,9 @@ static int isp116x_suspend(struct platform_device *dev, pm_message_t state) */ static int isp116x_resume(struct platform_device *dev) { - int ret = 0; - - VDBG("%s: state %x\n", __func__, dev->dev.power.power_state); - + VDBG("%s: state %x\n", __func__, dev->power.power_state.event); dev->dev.power.power_state = PMSG_ON; - - return ret; + return 0; } #else diff --git a/drivers/usb/host/isp116x.h b/drivers/usb/host/isp116x.h index c6fec96785f..a1b7c3813d3 100644 --- a/drivers/usb/host/isp116x.h +++ b/drivers/usb/host/isp116x.h @@ -259,7 +259,7 @@ struct isp116x { struct isp116x_platform_data *board; - struct proc_dir_entry *pde; + struct dentry *dentry; unsigned long stat1, stat2, stat4, stat8, stat16; /* HC registers */ @@ -450,7 +450,7 @@ static void isp116x_write_reg32(struct isp116x *isp116x, unsigned reg, isp116x_write_data32(isp116x, (u32) val); } -#define isp116x_show_reg(d,r) { \ +#define isp116x_show_reg_log(d,r,s) { \ if ((r) < 0x20) { \ DBG("%-12s[%02x]: %08x\n", #r, \ r, isp116x_read_reg32(d, r)); \ @@ -459,35 +459,60 @@ static void isp116x_write_reg32(struct isp116x *isp116x, unsigned reg, r, isp116x_read_reg16(d, r)); \ } \ } +#define isp116x_show_reg_seq(d,r,s) { \ + if ((r) < 0x20) { \ + seq_printf(s, "%-12s[%02x]: %08x\n", #r, \ + r, isp116x_read_reg32(d, r)); \ + } else { \ + seq_printf(s, "%-12s[%02x]: %04x\n", #r, \ + r, isp116x_read_reg16(d, r)); \ + } \ +} -static inline void isp116x_show_regs(struct isp116x *isp116x) +#define isp116x_show_regs(d,type,s) { \ + isp116x_show_reg_##type(d, HCREVISION, s); \ + isp116x_show_reg_##type(d, HCCONTROL, s); \ + isp116x_show_reg_##type(d, HCCMDSTAT, s); \ + isp116x_show_reg_##type(d, HCINTSTAT, s); \ + isp116x_show_reg_##type(d, HCINTENB, s); \ + isp116x_show_reg_##type(d, HCFMINTVL, s); \ + isp116x_show_reg_##type(d, HCFMREM, s); \ + isp116x_show_reg_##type(d, HCFMNUM, s); \ + isp116x_show_reg_##type(d, HCLSTHRESH, s); \ + isp116x_show_reg_##type(d, HCRHDESCA, s); \ + isp116x_show_reg_##type(d, HCRHDESCB, s); \ + isp116x_show_reg_##type(d, HCRHSTATUS, s); \ + isp116x_show_reg_##type(d, HCRHPORT1, s); \ + isp116x_show_reg_##type(d, HCRHPORT2, s); \ + isp116x_show_reg_##type(d, HCHWCFG, s); \ + isp116x_show_reg_##type(d, HCDMACFG, s); \ + isp116x_show_reg_##type(d, HCXFERCTR, s); \ + isp116x_show_reg_##type(d, HCuPINT, s); \ + isp116x_show_reg_##type(d, HCuPINTENB, s); \ + isp116x_show_reg_##type(d, HCCHIPID, s); \ + isp116x_show_reg_##type(d, HCSCRATCH, s); \ + isp116x_show_reg_##type(d, HCITLBUFLEN, s); \ + isp116x_show_reg_##type(d, HCATLBUFLEN, s); \ + isp116x_show_reg_##type(d, HCBUFSTAT, s); \ + isp116x_show_reg_##type(d, HCRDITL0LEN, s); \ + isp116x_show_reg_##type(d, HCRDITL1LEN, s); \ +} + +/* + Dump registers for debugfs. +*/ +static inline void isp116x_show_regs_seq(struct isp116x *isp116x, + struct seq_file *s) +{ + isp116x_show_regs(isp116x, seq, s); +} + +/* + Dump registers to syslog. +*/ +static inline void isp116x_show_regs_log(struct isp116x *isp116x) { - isp116x_show_reg(isp116x, HCREVISION); - isp116x_show_reg(isp116x, HCCONTROL); - isp116x_show_reg(isp116x, HCCMDSTAT); - isp116x_show_reg(isp116x, HCINTSTAT); - isp116x_show_reg(isp116x, HCINTENB); - isp116x_show_reg(isp116x, HCFMINTVL); - isp116x_show_reg(isp116x, HCFMREM); - isp116x_show_reg(isp116x, HCFMNUM); - isp116x_show_reg(isp116x, HCLSTHRESH); - isp116x_show_reg(isp116x, HCRHDESCA); - isp116x_show_reg(isp116x, HCRHDESCB); - isp116x_show_reg(isp116x, HCRHSTATUS); - isp116x_show_reg(isp116x, HCRHPORT1); - isp116x_show_reg(isp116x, HCRHPORT2); - isp116x_show_reg(isp116x, HCHWCFG); - isp116x_show_reg(isp116x, HCDMACFG); - isp116x_show_reg(isp116x, HCXFERCTR); - isp116x_show_reg(isp116x, HCuPINT); - isp116x_show_reg(isp116x, HCuPINTENB); - isp116x_show_reg(isp116x, HCCHIPID); - isp116x_show_reg(isp116x, HCSCRATCH); - isp116x_show_reg(isp116x, HCITLBUFLEN); - isp116x_show_reg(isp116x, HCATLBUFLEN); - isp116x_show_reg(isp116x, HCBUFSTAT); - isp116x_show_reg(isp116x, HCRDITL0LEN); - isp116x_show_reg(isp116x, HCRDITL1LEN); + isp116x_show_regs(isp116x, log, NULL); } #if defined(URB_TRACE) diff --git a/drivers/usb/host/ohci-hcd.c b/drivers/usb/host/ohci-hcd.c index bf1d9abc07a..a4b12404ae0 100644 --- a/drivers/usb/host/ohci-hcd.c +++ b/drivers/usb/host/ohci-hcd.c @@ -75,13 +75,6 @@ */ #include <linux/config.h> - -#ifdef CONFIG_USB_DEBUG -# define DEBUG -#else -# undef DEBUG -#endif - #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/pci.h> @@ -802,7 +795,6 @@ static int ohci_restart (struct ohci_hcd *ohci) int temp; int i; struct urb_priv *priv; - struct usb_device *root = ohci_to_hcd(ohci)->self.root_hub; /* mark any devices gone, so they do nothing till khubd disconnects. * recycle any "live" eds/tds (and urbs) right away. @@ -811,11 +803,7 @@ static int ohci_restart (struct ohci_hcd *ohci) */ spin_lock_irq(&ohci->lock); disable (ohci); - for (i = 0; i < root->maxchild; i++) { - if (root->children [i]) - usb_set_device_state (root->children[i], - USB_STATE_NOTATTACHED); - } + usb_root_hub_lost_power(ohci_to_hcd(ohci)->self.root_hub); if (!list_empty (&ohci->pending)) ohci_dbg(ohci, "abort schedule...\n"); list_for_each_entry (priv, &ohci->pending, pending) { diff --git a/drivers/usb/host/ohci-hub.c b/drivers/usb/host/ohci-hub.c index 72e3b12a192..4b2226d77b3 100644 --- a/drivers/usb/host/ohci-hub.c +++ b/drivers/usb/host/ohci-hub.c @@ -372,7 +372,7 @@ done: & ohci->hc_control) == OHCI_USB_OPER && time_after (jiffies, ohci->next_statechange) - && usb_trylock_device (hcd->self.root_hub) + && usb_trylock_device (hcd->self.root_hub) == 0 ) { ohci_vdbg (ohci, "autosuspend\n"); (void) ohci_bus_suspend (hcd); diff --git a/drivers/usb/host/ohci-pxa27x.c b/drivers/usb/host/ohci-pxa27x.c index 9d65ec30799..acde8868da2 100644 --- a/drivers/usb/host/ohci-pxa27x.c +++ b/drivers/usb/host/ohci-pxa27x.c @@ -26,18 +26,12 @@ #include <asm/mach-types.h> #include <asm/hardware.h> #include <asm/arch/pxa-regs.h> - - -#define PMM_NPS_MODE 1 -#define PMM_GLOBAL_MODE 2 -#define PMM_PERPORT_MODE 3 +#include <asm/arch/ohci.h> #define PXA_UHC_MAX_PORTNUM 3 #define UHCRHPS(x) __REG2( 0x4C000050, (x)<<2 ) -static int pxa27x_ohci_pmm_state; - /* PMM_NPS_MODE -- PMM Non-power switching mode Ports are powered continuously. @@ -50,8 +44,6 @@ static int pxa27x_ohci_pmm_state; */ static int pxa27x_ohci_select_pmm( int mode ) { - pxa27x_ohci_pmm_state = mode; - switch ( mode ) { case PMM_NPS_MODE: UHCRHDA |= RH_A_NPS; @@ -71,7 +63,6 @@ static int pxa27x_ohci_select_pmm( int mode ) "Invalid mode %d, set to non-power switch mode.\n", mode ); - pxa27x_ohci_pmm_state = PMM_NPS_MODE; UHCRHDA |= RH_A_NPS; } @@ -82,8 +73,13 @@ extern int usb_disabled(void); /*-------------------------------------------------------------------------*/ -static void pxa27x_start_hc(struct platform_device *dev) +static int pxa27x_start_hc(struct device *dev) { + int retval = 0; + struct pxaohci_platform_data *inf; + + inf = dev->platform_data; + pxa_set_cken(CKEN10_USBHOST, 1); UHCHR |= UHCHR_FHR; @@ -94,21 +90,11 @@ static void pxa27x_start_hc(struct platform_device *dev) while (UHCHR & UHCHR_FSBIR) cpu_relax(); - /* This could be properly abstracted away through the - device data the day more machines are supported and - their differences can be figured out correctly. */ - if (machine_is_mainstone()) { - /* setup Port1 GPIO pin. */ - pxa_gpio_mode( 88 | GPIO_ALT_FN_1_IN); /* USBHPWR1 */ - pxa_gpio_mode( 89 | GPIO_ALT_FN_2_OUT); /* USBHPEN1 */ - - /* Set the Power Control Polarity Low and Power Sense - Polarity Low to active low. Supply power to USB ports. */ - UHCHR = (UHCHR | UHCHR_PCPL | UHCHR_PSPL) & - ~(UHCHR_SSEP1 | UHCHR_SSEP2 | UHCHR_SSEP3 | UHCHR_SSE); + if (inf->init) + retval = inf->init(dev); - pxa27x_ohci_pmm_state = PMM_PERPORT_MODE; - } + if (retval < 0) + return retval; UHCHR &= ~UHCHR_SSE; @@ -117,10 +103,19 @@ static void pxa27x_start_hc(struct platform_device *dev) /* Clear any OTG Pin Hold */ if (PSSR & PSSR_OTGPH) PSSR |= PSSR_OTGPH; + + return 0; } -static void pxa27x_stop_hc(struct platform_device *dev) +static void pxa27x_stop_hc(struct device *dev) { + struct pxaohci_platform_data *inf; + + inf = dev->platform_data; + + if (inf->exit) + inf->exit(dev); + UHCHR |= UHCHR_FHR; udelay(11); UHCHR &= ~UHCHR_FHR; @@ -147,22 +142,27 @@ static void pxa27x_stop_hc(struct platform_device *dev) * through the hotplug entry's driver_data. * */ -int usb_hcd_pxa27x_probe (const struct hc_driver *driver, - struct platform_device *dev) +int usb_hcd_pxa27x_probe (const struct hc_driver *driver, struct platform_device *pdev) { int retval; struct usb_hcd *hcd; + struct pxaohci_platform_data *inf; - if (dev->resource[1].flags != IORESOURCE_IRQ) { + inf = pdev->dev.platform_data; + + if (!inf) + return -ENODEV; + + if (pdev->resource[1].flags != IORESOURCE_IRQ) { pr_debug ("resource[1] is not IORESOURCE_IRQ"); return -ENOMEM; } - hcd = usb_create_hcd (driver, &dev->dev, "pxa27x"); + hcd = usb_create_hcd (driver, &pdev->dev, "pxa27x"); if (!hcd) return -ENOMEM; - hcd->rsrc_start = dev->resource[0].start; - hcd->rsrc_len = dev->resource[0].end - dev->resource[0].start + 1; + hcd->rsrc_start = pdev->resource[0].start; + hcd->rsrc_len = pdev->resource[0].end - pdev->resource[0].start + 1; if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len, hcd_name)) { pr_debug("request_mem_region failed"); @@ -177,18 +177,22 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, goto err2; } - pxa27x_start_hc(dev); + if ((retval = pxa27x_start_hc(&pdev->dev)) < 0) { + pr_debug("pxa27x_start_hc failed"); + goto err3; + } /* Select Power Management Mode */ - pxa27x_ohci_select_pmm(pxa27x_ohci_pmm_state); + pxa27x_ohci_select_pmm(inf->port_mode); ohci_hcd_init(hcd_to_ohci(hcd)); - retval = usb_add_hcd(hcd, dev->resource[1].start, SA_INTERRUPT); + retval = usb_add_hcd(hcd, pdev->resource[1].start, SA_INTERRUPT); if (retval == 0) return retval; - pxa27x_stop_hc(dev); + pxa27x_stop_hc(&pdev->dev); + err3: iounmap(hcd->regs); err2: release_mem_region(hcd->rsrc_start, hcd->rsrc_len); @@ -211,10 +215,10 @@ int usb_hcd_pxa27x_probe (const struct hc_driver *driver, * context, normally "rmmod", "apmd", or something similar. * */ -void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *dev) +void usb_hcd_pxa27x_remove (struct usb_hcd *hcd, struct platform_device *pdev) { usb_remove_hcd(hcd); - pxa27x_stop_hc(dev); + pxa27x_stop_hc(&pdev->dev); iounmap(hcd->regs); release_mem_region(hcd->rsrc_start, hcd->rsrc_len); usb_put_hcd(hcd); @@ -292,15 +296,12 @@ static const struct hc_driver ohci_pxa27x_hc_driver = { static int ohci_hcd_pxa27x_drv_probe(struct platform_device *pdev) { - int ret; - pr_debug ("In ohci_hcd_pxa27x_drv_probe"); if (usb_disabled()) return -ENODEV; - ret = usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev); - return ret; + return usb_hcd_pxa27x_probe(&ohci_pxa27x_hc_driver, pdev); } static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev) @@ -308,31 +309,55 @@ static int ohci_hcd_pxa27x_drv_remove(struct platform_device *pdev) struct usb_hcd *hcd = platform_get_drvdata(pdev); usb_hcd_pxa27x_remove(hcd, pdev); + platform_set_drvdata(pdev, NULL); return 0; } -static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *dev, pm_message_t state) +#ifdef CONFIG_PM +static int ohci_hcd_pxa27x_drv_suspend(struct platform_device *pdev, pm_message_t state) { -// struct usb_hcd *hcd = platform_get_drvdata(dev); - printk("%s: not implemented yet\n", __FUNCTION__); + struct usb_hcd *hcd = platform_get_drvdata(pdev); + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + + if (time_before(jiffies, ohci->next_statechange)) + msleep(5); + ohci->next_statechange = jiffies; + + pxa27x_stop_hc(&pdev->dev); + hcd->state = HC_STATE_SUSPENDED; + pdev->dev.power.power_state = PMSG_SUSPEND; return 0; } -static int ohci_hcd_pxa27x_drv_resume(struct platform_device *dev) +static int ohci_hcd_pxa27x_drv_resume(struct platform_device *pdev) { -// struct usb_hcd *hcd = platform_get_drvdata(dev); - printk("%s: not implemented yet\n", __FUNCTION__); + struct usb_hcd *hcd = platform_get_drvdata(pdev); + struct ohci_hcd *ohci = hcd_to_ohci(hcd); + int status; + + if (time_before(jiffies, ohci->next_statechange)) + msleep(5); + ohci->next_statechange = jiffies; + + if ((status = pxa27x_start_hc(&pdev->dev)) < 0) + return status; + + pdev->dev.power.power_state = PMSG_ON; + usb_hcd_resume_root_hub(hcd); return 0; } +#endif static struct platform_driver ohci_hcd_pxa27x_driver = { .probe = ohci_hcd_pxa27x_drv_probe, .remove = ohci_hcd_pxa27x_drv_remove, +#ifdef CONFIG_PM .suspend = ohci_hcd_pxa27x_drv_suspend, .resume = ohci_hcd_pxa27x_drv_resume, +#endif .driver = { .name = "pxa27x-ohci", }, diff --git a/drivers/usb/host/pci-quirks.c b/drivers/usb/host/pci-quirks.c index e46528c825b..3ef2c0cdf1d 100644 --- a/drivers/usb/host/pci-quirks.c +++ b/drivers/usb/host/pci-quirks.c @@ -9,12 +9,6 @@ */ #include <linux/config.h> -#ifdef CONFIG_USB_DEBUG -#define DEBUG -#else -#undef DEBUG -#endif - #include <linux/types.h> #include <linux/kernel.h> #include <linux/pci.h> diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c index a7722a6a5a5..517360b77d8 100644 --- a/drivers/usb/host/sl811-hcd.c +++ b/drivers/usb/host/sl811-hcd.c @@ -32,13 +32,6 @@ #undef PACKET_TRACE #include <linux/config.h> - -#ifdef CONFIG_USB_DEBUG -# define DEBUG -#else -# undef DEBUG -#endif - #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/kernel.h> @@ -1581,7 +1574,9 @@ sl811h_start(struct usb_hcd *hcd) hcd->state = HC_STATE_RUNNING; if (sl811->board) { - hcd->can_wakeup = sl811->board->can_wakeup; + if (!device_can_wakeup(hcd->self.controller)) + device_init_wakeup(hcd->self.controller, + sl811->board->can_wakeup); hcd->power_budget = sl811->board->power * 2; } @@ -1805,9 +1800,10 @@ sl811h_resume(struct platform_device *dev) * let's assume it'd only be powered to enable remote wakeup. */ if (dev->dev.power.power_state.event == PM_EVENT_SUSPEND - || !hcd->can_wakeup) { + || !device_can_wakeup(&hcd->self.root_hub->dev)) { sl811->port1 = 0; port_power(sl811, 1); + usb_root_hub_lost_power(hcd->self.root_hub); return 0; } diff --git a/drivers/usb/host/sl811_cs.c b/drivers/usb/host/sl811_cs.c index e73faf831b2..466384d7c79 100644 --- a/drivers/usb/host/sl811_cs.c +++ b/drivers/usb/host/sl811_cs.c @@ -38,7 +38,7 @@ MODULE_LICENSE("GPL"); /* MACROS */ /*====================================================================*/ -#if defined(DEBUG) || defined(CONFIG_USB_DEBUG) || defined(PCMCIA_DEBUG) +#if defined(DEBUG) || defined(PCMCIA_DEBUG) static int pc_debug = 0; module_param(pc_debug, int, 0644); @@ -66,13 +66,13 @@ module_param(pc_debug, int, 0644); static const char driver_name[DEV_NAME_LEN] = "sl811_cs"; -static dev_link_t *dev_list = NULL; - typedef struct local_info_t { dev_link_t link; dev_node_t node; } local_info_t; +static void sl811_cs_release(dev_link_t * link); + /*====================================================================*/ static void release_platform_dev(struct device * dev) @@ -129,7 +129,8 @@ static int sl811_hc_init(struct device *parent, ioaddr_t base_addr, int irq) resources[2].end = base_addr + 1; /* The driver core will probe for us. We know sl811-hcd has been - * initialized already because of the link order dependency. + * initialized already because of the link order dependency created + * by referencing "sl811h_driver". */ platform_dev.name = sl811h_driver.name; return platform_device_register(&platform_dev); @@ -137,26 +138,16 @@ static int sl811_hc_init(struct device *parent, ioaddr_t base_addr, int irq) /*====================================================================*/ -static void sl811_cs_detach(dev_link_t *link) +static void sl811_cs_detach(struct pcmcia_device *p_dev) { - dev_link_t **linkp; + dev_link_t *link = dev_to_instance(p_dev); DBG(0, "sl811_cs_detach(0x%p)\n", link); - /* Locate device structure */ - for (linkp = &dev_list; *linkp; linkp = &(*linkp)->next) { - if (*linkp == link) - break; - } - if (*linkp == NULL) - return; - - /* Break the link with Card Services */ - if (link->handle) - pcmcia_deregister_client(link->handle); + link->state &= ~DEV_PRESENT; + if (link->state & DEV_CONFIG) + sl811_cs_release(link); - /* Unlink device structure, and free it */ - *linkp = link->next; /* This points to the parent local_info_t struct */ kfree(link->priv); } @@ -166,13 +157,6 @@ static void sl811_cs_release(dev_link_t * link) DBG(0, "sl811_cs_release(0x%p)\n", link); - if (link->open) { - DBG(1, "sl811_cs: release postponed, '%s' still open\n", - link->dev->dev_name); - link->state |= DEV_STALE_CONFIG; - return; - } - /* Unlink the device chain */ link->dev = NULL; @@ -183,9 +167,6 @@ static void sl811_cs_release(dev_link_t * link) if (link->irq.AssignedIRQ) pcmcia_release_irq(link->handle, &link->irq); link->state &= ~DEV_CONFIG; - - if (link->state & DEV_STALE_LINK) - sl811_cs_detach(link); } static void sl811_cs_config(dev_link_t *link) @@ -322,55 +303,36 @@ cs_failed: } } -static int -sl811_cs_event(event_t event, int priority, event_callback_args_t *args) +static int sl811_suspend(struct pcmcia_device *dev) { - dev_link_t *link = args->client_data; + dev_link_t *link = dev_to_instance(dev); - DBG(1, "sl811_cs_event(0x%06x)\n", event); + link->state |= DEV_SUSPEND; + if (link->state & DEV_CONFIG) + pcmcia_release_configuration(link->handle); - switch (event) { - case CS_EVENT_CARD_REMOVAL: - link->state &= ~DEV_PRESENT; - if (link->state & DEV_CONFIG) - sl811_cs_release(link); - break; + return 0; +} - case CS_EVENT_CARD_INSERTION: - link->state |= DEV_PRESENT | DEV_CONFIG_PENDING; - sl811_cs_config(link); - break; +static int sl811_resume(struct pcmcia_device *dev) +{ + dev_link_t *link = dev_to_instance(dev); - case CS_EVENT_PM_SUSPEND: - link->state |= DEV_SUSPEND; - /* Fall through... */ - case CS_EVENT_RESET_PHYSICAL: - if (link->state & DEV_CONFIG) - pcmcia_release_configuration(link->handle); - break; + link->state &= ~DEV_SUSPEND; + if (link->state & DEV_CONFIG) + pcmcia_request_configuration(link->handle, &link->conf); - case CS_EVENT_PM_RESUME: - link->state &= ~DEV_SUSPEND; - /* Fall through... */ - case CS_EVENT_CARD_RESET: - if (link->state & DEV_CONFIG) - pcmcia_request_configuration(link->handle, &link->conf); - DBG(0, "reset sl811-hcd here?\n"); - break; - } return 0; } -static dev_link_t *sl811_cs_attach(void) +static int sl811_cs_attach(struct pcmcia_device *p_dev) { local_info_t *local; dev_link_t *link; - client_reg_t client_reg; - int ret; local = kmalloc(sizeof(local_info_t), GFP_KERNEL); if (!local) - return NULL; + return -ENOMEM; memset(local, 0, sizeof(local_info_t)); link = &local->link; link->priv = local; @@ -384,21 +346,13 @@ static dev_link_t *sl811_cs_attach(void) link->conf.Vcc = 33; link->conf.IntType = INT_MEMORY_AND_IO; - /* Register with Card Services */ - link->next = dev_list; - dev_list = link; - client_reg.dev_info = (dev_info_t *) &driver_name; - client_reg.Attributes = INFO_IO_CLIENT | INFO_CARD_SHARE; - client_reg.Version = 0x0210; - client_reg.event_callback_args.client_data = link; - ret = pcmcia_register_client(&link->handle, &client_reg); - if (ret != CS_SUCCESS) { - cs_error(link->handle, RegisterClient, ret); - sl811_cs_detach(link); - return NULL; - } + link->handle = p_dev; + p_dev->instance = link; - return link; + link->state |= DEV_PRESENT | DEV_CONFIG_PENDING; + sl811_cs_config(link); + + return 0; } static struct pcmcia_device_id sl811_ids[] = { @@ -412,10 +366,11 @@ static struct pcmcia_driver sl811_cs_driver = { .drv = { .name = (char *)driver_name, }, - .attach = sl811_cs_attach, - .event = sl811_cs_event, - .detach = sl811_cs_detach, + .probe = sl811_cs_attach, + .remove = sl811_cs_detach, .id_table = sl811_ids, + .suspend = sl811_suspend, + .resume = sl811_resume, }; /*====================================================================*/ diff --git a/drivers/usb/host/uhci-debug.c b/drivers/usb/host/uhci-debug.c index 151154df37f..5832953086f 100644 --- a/drivers/usb/host/uhci-debug.c +++ b/drivers/usb/host/uhci-debug.c @@ -2,8 +2,8 @@ * UHCI-specific debugging code. Invaluable when something * goes wrong, but don't get in my face. * - * Kernel visible pointers are surrounded in []'s and bus - * visible pointers are surrounded in ()'s + * Kernel visible pointers are surrounded in []s and bus + * visible pointers are surrounded in ()s * * (C) Copyright 1999 Linus Torvalds * (C) Copyright 1999-2001 Johannes Erdfelt @@ -19,7 +19,7 @@ static struct dentry *uhci_debugfs_root = NULL; -/* Handle REALLY large printk's so we don't overflow buffers */ +/* Handle REALLY large printks so we don't overflow buffers */ static inline void lprintk(char *buf) { char *p; @@ -160,7 +160,7 @@ static int uhci_show_qh(struct uhci_qh *qh, char *buf, int len, int space) } if (active && ni > i) { - out += sprintf(out, "%*s[skipped %d active TD's]\n", space, "", ni - i); + out += sprintf(out, "%*s[skipped %d active TDs]\n", space, "", ni - i); tmp = ntmp; td = ntd; i = ni; @@ -173,7 +173,7 @@ static int uhci_show_qh(struct uhci_qh *qh, char *buf, int len, int space) if (list_empty(&urbp->queue_list) || urbp->queued) goto out; - out += sprintf(out, "%*sQueued QH's:\n", -space, "--"); + out += sprintf(out, "%*sQueued QHs:\n", -space, "--"); head = &urbp->queue_list; tmp = head->next; @@ -197,7 +197,7 @@ out: } #ifdef CONFIG_PROC_FS -static const char *qh_names[] = { +static const char * const qh_names[] = { "skel_int128_qh", "skel_int64_qh", "skel_int32_qh", "skel_int16_qh", "skel_int8_qh", "skel_int4_qh", @@ -464,7 +464,7 @@ static int uhci_sprint_schedule(struct uhci_hcd *uhci, char *buf, int len) } while (tmp != head); } - out += sprintf(out, "Skeleton QH's\n"); + out += sprintf(out, "Skeleton QHs\n"); for (i = 0; i < UHCI_NUM_SKELQH; ++i) { int shown = 0; diff --git a/drivers/usb/host/uhci-hcd.c b/drivers/usb/host/uhci-hcd.c index ed550132db0..dfe121d3588 100644 --- a/drivers/usb/host/uhci-hcd.c +++ b/drivers/usb/host/uhci-hcd.c @@ -23,11 +23,6 @@ */ #include <linux/config.h> -#ifdef CONFIG_USB_DEBUG -#define DEBUG -#else -#undef DEBUG -#endif #include <linux/module.h> #include <linux/pci.h> #include <linux/kernel.h> @@ -67,10 +62,10 @@ Alan Stern" /* * debug = 0, no debugging messages - * debug = 1, dump failed URB's except for stalls - * debug = 2, dump all failed URB's (including stalls) + * debug = 1, dump failed URBs except for stalls + * debug = 2, dump all failed URBs (including stalls) * show all queues in /debug/uhci/[pci_addr] - * debug = 3, show all TD's in URB's when dumping + * debug = 3, show all TDs in URBs when dumping */ #ifdef DEBUG static int debug = 1; @@ -93,7 +88,7 @@ static void uhci_get_current_frame_number(struct uhci_hcd *uhci); #define FSBR_DELAY msecs_to_jiffies(50) /* When we timeout an idle transfer for FSBR, we'll switch it over to */ -/* depth first traversal. We'll do it in groups of this number of TD's */ +/* depth first traversal. We'll do it in groups of this number of TDs */ /* to make sure it doesn't hog all of the bandwidth */ #define DEPTH_INTERVAL 5 @@ -478,8 +473,6 @@ static int uhci_start(struct usb_hcd *hcd) struct dentry *dentry; hcd->uses_new_polling = 1; - if (pci_find_capability(to_pci_dev(uhci_dev(uhci)), PCI_CAP_ID_PM)) - hcd->can_wakeup = 1; /* Assume it supports PME# */ dentry = debugfs_create_file(hcd->self.bus_name, S_IFREG|S_IRUGO|S_IWUSR, uhci_debugfs_root, uhci, @@ -573,7 +566,7 @@ static int uhci_start(struct usb_hcd *hcd) uhci->skel_bulk_qh->link = cpu_to_le32(uhci->skel_term_qh->dma_handle) | UHCI_PTR_QH; /* This dummy TD is to work around a bug in Intel PIIX controllers */ - uhci_fill_td(uhci->term_td, 0, (UHCI_NULL_DATA_SIZE << 21) | + uhci_fill_td(uhci->term_td, 0, uhci_explen(0) | (0x7f << TD_TOKEN_DEVADDR_SHIFT) | USB_PID_IN, 0); uhci->term_td->link = cpu_to_le32(uhci->term_td->dma_handle); @@ -717,6 +710,7 @@ static int uhci_suspend(struct usb_hcd *hcd, pm_message_t message) * at the source, so we must turn off PIRQ. */ pci_write_config_word(to_pci_dev(uhci_dev(uhci)), USBLEGSUP, 0); + mb(); clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); uhci->hc_inaccessible = 1; hcd->poll_rh = 0; @@ -734,10 +728,12 @@ static int uhci_resume(struct usb_hcd *hcd) dev_dbg(uhci_dev(uhci), "%s\n", __FUNCTION__); - /* We aren't in D3 state anymore, we do that even if dead as I - * really don't want to keep a stale HCD_FLAG_HW_ACCESSIBLE=0 + /* Since we aren't in D3 any more, it's safe to set this flag + * even if the controller was dead. It might not even be dead + * any more, if the firmware or quirks code has reset it. */ set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); + mb(); if (uhci->rh_state == UHCI_RH_RESET) /* Dead */ return 0; @@ -753,8 +749,12 @@ static int uhci_resume(struct usb_hcd *hcd) check_and_reset_hc(uhci); configure_hc(uhci); - if (uhci->rh_state == UHCI_RH_RESET) + if (uhci->rh_state == UHCI_RH_RESET) { + + /* The controller had to be reset */ + usb_root_hub_lost_power(hcd->self.root_hub); suspend_rh(uhci, UHCI_RH_SUSPENDED); + } spin_unlock_irq(&uhci->lock); @@ -880,7 +880,7 @@ static int __init uhci_hcd_init(void) init_failed: if (kmem_cache_destroy(uhci_up_cachep)) - warn("not all urb_priv's were freed!"); + warn("not all urb_privs were freed!"); up_failed: debugfs_remove(uhci_debugfs_root); @@ -898,7 +898,7 @@ static void __exit uhci_hcd_cleanup(void) pci_unregister_driver(&uhci_pci_driver); if (kmem_cache_destroy(uhci_up_cachep)) - warn("not all urb_priv's were freed!"); + warn("not all urb_privs were freed!"); debugfs_remove(uhci_debugfs_root); kfree(errbuf); diff --git a/drivers/usb/host/uhci-hcd.h b/drivers/usb/host/uhci-hcd.h index e576db57a92..8b4b887a7d4 100644 --- a/drivers/usb/host/uhci-hcd.h +++ b/drivers/usb/host/uhci-hcd.h @@ -71,8 +71,6 @@ #define USBLEGSUP_RWC 0x8f00 /* the R/WC bits */ #define USBLEGSUP_RO 0x5040 /* R/O and reserved bits */ -#define UHCI_NULL_DATA_SIZE 0x7FF /* for UHCI controller TD */ - #define UHCI_PTR_BITS cpu_to_le32(0x000F) #define UHCI_PTR_TERM cpu_to_le32(0x0001) #define UHCI_PTR_QH cpu_to_le32(0x0002) @@ -168,9 +166,11 @@ static __le32 inline qh_element(struct uhci_qh *qh) { #define TD_TOKEN_EXPLEN_MASK 0x7FF /* expected length, encoded as n - 1 */ #define TD_TOKEN_PID_MASK 0xFF -#define uhci_explen(len) ((len) << TD_TOKEN_EXPLEN_SHIFT) +#define uhci_explen(len) ((((len) - 1) & TD_TOKEN_EXPLEN_MASK) << \ + TD_TOKEN_EXPLEN_SHIFT) -#define uhci_expected_length(token) ((((token) >> 21) + 1) & TD_TOKEN_EXPLEN_MASK) +#define uhci_expected_length(token) ((((token) >> TD_TOKEN_EXPLEN_SHIFT) + \ + 1) & TD_TOKEN_EXPLEN_MASK) #define uhci_toggle(token) (((token) >> TD_TOKEN_TOGGLE_SHIFT) & 1) #define uhci_endpoint(token) (((token) >> 15) & 0xf) #define uhci_devaddr(token) (((token) >> TD_TOKEN_DEVADDR_SHIFT) & 0x7f) @@ -223,10 +223,10 @@ static u32 inline td_status(struct uhci_td *td) { */ /* - * The UHCI driver places Interrupt, Control and Bulk into QH's both - * to group together TD's for one transfer, and also to faciliate queuing - * of URB's. To make it easy to insert entries into the schedule, we have - * a skeleton of QH's for each predefined Interrupt latency, low-speed + * The UHCI driver places Interrupt, Control and Bulk into QHs both + * to group together TDs for one transfer, and also to facilitate queuing + * of URBs. To make it easy to insert entries into the schedule, we have + * a skeleton of QHs for each predefined Interrupt latency, low-speed * control, full-speed control and terminating QH (see explanation for * the terminating QH below). * @@ -257,8 +257,8 @@ static u32 inline td_status(struct uhci_td *td) { * reclamation. * * Isochronous transfers are stored before the start of the skeleton - * schedule and don't use QH's. While the UHCI spec doesn't forbid the - * use of QH's for Isochronous, it doesn't use them either. And the spec + * schedule and don't use QHs. While the UHCI spec doesn't forbid the + * use of QHs for Isochronous, it doesn't use them either. And the spec * says that queues never advance on an error completion status, which * makes them totally unsuitable for Isochronous transfers. */ @@ -359,7 +359,7 @@ struct uhci_hcd { struct dma_pool *td_pool; struct uhci_td *term_td; /* Terminating TD, see UHCI bug */ - struct uhci_qh *skelqh[UHCI_NUM_SKELQH]; /* Skeleton QH's */ + struct uhci_qh *skelqh[UHCI_NUM_SKELQH]; /* Skeleton QHs */ spinlock_t lock; @@ -389,22 +389,22 @@ struct uhci_hcd { unsigned long resuming_ports; unsigned long ports_timeout; /* Time to stop signalling */ - /* Main list of URB's currently controlled by this HC */ + /* Main list of URBs currently controlled by this HC */ struct list_head urb_list; - /* List of QH's that are done, but waiting to be unlinked (race) */ + /* List of QHs that are done, but waiting to be unlinked (race) */ struct list_head qh_remove_list; unsigned int qh_remove_age; /* Age in frames */ - /* List of TD's that are done, but waiting to be freed (race) */ + /* List of TDs that are done, but waiting to be freed (race) */ struct list_head td_remove_list; unsigned int td_remove_age; /* Age in frames */ - /* List of asynchronously unlinked URB's */ + /* List of asynchronously unlinked URBs */ struct list_head urb_remove_list; unsigned int urb_remove_age; /* Age in frames */ - /* List of URB's awaiting completion callback */ + /* List of URBs awaiting completion callback */ struct list_head complete_list; int rh_numports; /* Number of root-hub ports */ diff --git a/drivers/usb/host/uhci-q.c b/drivers/usb/host/uhci-q.c index 7e46887d9e1..b6076004a43 100644 --- a/drivers/usb/host/uhci-q.c +++ b/drivers/usb/host/uhci-q.c @@ -80,7 +80,7 @@ static inline void uhci_fill_td(struct uhci_td *td, u32 status, } /* - * We insert Isochronous URB's directly into the frame list at the beginning + * We insert Isochronous URBs directly into the frame list at the beginning */ static void uhci_insert_td_frame_list(struct uhci_hcd *uhci, struct uhci_td *td, unsigned framenum) { @@ -369,7 +369,7 @@ static void uhci_append_queued_urb(struct uhci_hcd *uhci, struct urb *eurb, stru uhci_fixup_toggle(urb, uhci_toggle(td_token(lltd)) ^ 1)); - /* All qh's in the queue need to link to the next queue */ + /* All qhs in the queue need to link to the next queue */ urbp->qh->link = eurbp->qh->link; wmb(); /* Make sure we flush everything */ @@ -502,7 +502,7 @@ static void uhci_destroy_urb_priv(struct uhci_hcd *uhci, struct urb *urb) } /* Check to see if the remove list is empty. Set the IOC bit */ - /* to force an interrupt so we can remove the TD's*/ + /* to force an interrupt so we can remove the TDs*/ if (list_empty(&uhci->td_remove_list)) uhci_set_next_interrupt(uhci); @@ -596,7 +596,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb, struct ur return -ENOMEM; uhci_add_td_to_urb(urb, td); - uhci_fill_td(td, status, destination | uhci_explen(7), + uhci_fill_td(td, status, destination | uhci_explen(8), urb->setup_dma); /* @@ -612,7 +612,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb, struct ur } /* - * Build the DATA TD's + * Build the DATA TDs */ while (len > 0) { int pktsze = len; @@ -628,7 +628,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb, struct ur destination ^= TD_TOKEN_TOGGLE; uhci_add_td_to_urb(urb, td); - uhci_fill_td(td, status, destination | uhci_explen(pktsze - 1), + uhci_fill_td(td, status, destination | uhci_explen(pktsze), data); data += pktsze; @@ -658,7 +658,7 @@ static int uhci_submit_control(struct uhci_hcd *uhci, struct urb *urb, struct ur uhci_add_td_to_urb(urb, td); uhci_fill_td(td, status | TD_CTRL_IOC, - destination | uhci_explen(UHCI_NULL_DATA_SIZE), 0); + destination | uhci_explen(0), 0); qh = uhci_alloc_qh(uhci); if (!qh) @@ -744,7 +744,7 @@ static int uhci_result_control(struct uhci_hcd *uhci, struct urb *urb) urb->actual_length = 0; - /* The rest of the TD's (but the last) are data */ + /* The rest of the TDs (but the last) are data */ tmp = tmp->next; while (tmp != head && tmp->next != head) { unsigned int ctrlstat; @@ -848,7 +848,7 @@ static int uhci_submit_common(struct uhci_hcd *uhci, struct urb *urb, struct urb status |= TD_CTRL_SPD; /* - * Build the DATA TD's + * Build the DATA TDs */ do { /* Allow zero length packets */ int pktsze = maxsze; @@ -864,7 +864,7 @@ static int uhci_submit_common(struct uhci_hcd *uhci, struct urb *urb, struct urb return -ENOMEM; uhci_add_td_to_urb(urb, td); - uhci_fill_td(td, status, destination | uhci_explen(pktsze - 1) | + uhci_fill_td(td, status, destination | uhci_explen(pktsze) | (usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe), usb_pipeout(urb->pipe)) << TD_TOKEN_TOGGLE_SHIFT), data); @@ -890,7 +890,7 @@ static int uhci_submit_common(struct uhci_hcd *uhci, struct urb *urb, struct urb return -ENOMEM; uhci_add_td_to_urb(urb, td); - uhci_fill_td(td, status, destination | uhci_explen(UHCI_NULL_DATA_SIZE) | + uhci_fill_td(td, status, destination | uhci_explen(0) | (usb_gettoggle(urb->dev, usb_pipeendpoint(urb->pipe), usb_pipeout(urb->pipe)) << TD_TOKEN_TOGGLE_SHIFT), data); @@ -1025,7 +1025,7 @@ static int isochronous_find_limits(struct uhci_hcd *uhci, struct urb *urb, unsig list_for_each_entry(up, &uhci->urb_list, urb_list) { struct urb *u = up->urb; - /* look for pending URB's with identical pipe handle */ + /* look for pending URBs with identical pipe handle */ if ((urb->pipe == u->pipe) && (urb->dev == u->dev) && (u->status == -EINPROGRESS) && (u != urb)) { if (!last_urb) @@ -1092,7 +1092,7 @@ static int uhci_submit_isochronous(struct uhci_hcd *uhci, struct urb *urb) return -ENOMEM; uhci_add_td_to_urb(urb, td); - uhci_fill_td(td, status, destination | uhci_explen(urb->iso_frame_desc[i].length - 1), + uhci_fill_td(td, status, destination | uhci_explen(urb->iso_frame_desc[i].length), urb->transfer_dma + urb->iso_frame_desc[i].offset); if (i + 1 >= urb->number_of_packets) @@ -1355,7 +1355,7 @@ static void uhci_unlink_generic(struct uhci_hcd *uhci, struct urb *urb) uhci_delete_queued_urb(uhci, urb); - /* The interrupt loop will reclaim the QH's */ + /* The interrupt loop will reclaim the QHs */ uhci_remove_qh(uhci, urbp->qh); urbp->qh = NULL; } @@ -1413,7 +1413,7 @@ static int uhci_fsbr_timeout(struct uhci_hcd *uhci, struct urb *urb) list_for_each_entry(td, head, list) { /* * Make sure we don't do the last one (since it'll have the - * TERM bit set) as well as we skip every so many TD's to + * TERM bit set) as well as we skip every so many TDs to * make sure it doesn't hog the bandwidth */ if (td->list.next != head && (count % DEPTH_INTERVAL) == |