1 files changed, 270 insertions, 140 deletions

diff --git a/drivers/usb/musb/am35x.c b/drivers/usb/musb/am35x.c
index b0aabf3a606..d5a3da37c90 100644
--- a/drivers/usb/musb/am35x.c
+++ b/drivers/usb/musb/am35x.c
@@ -29,8 +29,9 @@
 #include <linux/init.h>
 #include <linux/clk.h>
 #include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/dma-mapping.h>
 
-#include <plat/control.h>
 #include <plat/usb.h>
 
 #include "musb_core.h"
@@ -80,51 +81,18 @@
 
 #define USB_MENTOR_CORE_OFFSET	0x400
 
-static inline void phy_on(void)
-{
-	unsigned long timeout = jiffies + msecs_to_jiffies(100);
-	u32 devconf2;
-
-	/*
-	 * Start the on-chip PHY and its PLL.
-	 */
-	devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
-
-	devconf2 &= ~(CONF2_RESET | CONF2_PHYPWRDN | CONF2_OTGPWRDN);
-	devconf2 |= CONF2_PHY_PLLON;
-
-	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
-
-	DBG(1, "Waiting for PHY clock good...\n");
-	while (!(omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2)
-			& CONF2_PHYCLKGD)) {
-		cpu_relax();
-
-		if (time_after(jiffies, timeout)) {
-			DBG(1, "musb PHY clock good timed out\n");
-			break;
-		}
-	}
-}
-
-static inline void phy_off(void)
-{
-	u32 devconf2;
-
-	/*
-	 * Power down the on-chip PHY.
-	 */
-	devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
-
-	devconf2 &= ~CONF2_PHY_PLLON;
-	devconf2 |=  CONF2_PHYPWRDN | CONF2_OTGPWRDN;
-	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
-}
+struct am35x_glue {
+	struct device		*dev;
+	struct platform_device	*musb;
+	struct clk		*phy_clk;
+	struct clk		*clk;
+};
+#define glue_to_musb(g)		platform_get_drvdata(g->musb)
 
 /*
- * musb_platform_enable - enable interrupts
+ * am35x_musb_enable - enable interrupts
  */
-void musb_platform_enable(struct musb *musb)
+static void am35x_musb_enable(struct musb *musb)
 {
 	void __iomem *reg_base = musb->ctrl_base;
 	u32 epmask;
@@ -143,9 +111,9 @@ void musb_platform_enable(struct musb *musb)
 }
 
 /*
- * musb_platform_disable - disable HDRC and flush interrupts
+ * am35x_musb_disable - disable HDRC and flush interrupts
  */
-void musb_platform_disable(struct musb *musb)
+static void am35x_musb_disable(struct musb *musb)
 {
 	void __iomem *reg_base = musb->ctrl_base;
 
@@ -162,7 +130,7 @@ void musb_platform_disable(struct musb *musb)
 #define portstate(stmt)
 #endif
 
-static void am35x_set_vbus(struct musb *musb, int is_on)
+static void am35x_musb_set_vbus(struct musb *musb, int is_on)
 {
 	WARN_ON(is_on && is_peripheral_active(musb));
 }
@@ -221,7 +189,7 @@ static void otg_timer(unsigned long _musb)
 	spin_unlock_irqrestore(&musb->lock, flags);
 }
 
-void musb_platform_try_idle(struct musb *musb, unsigned long timeout)
+static void am35x_musb_try_idle(struct musb *musb, unsigned long timeout)
 {
 	static unsigned long last_timer;
 
@@ -251,13 +219,16 @@ void musb_platform_try_idle(struct musb *musb, unsigned long timeout)
 	mod_timer(&otg_workaround, timeout);
 }
 
-static irqreturn_t am35x_interrupt(int irq, void *hci)
+static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
 {
 	struct musb  *musb = hci;
 	void __iomem *reg_base = musb->ctrl_base;
+	struct device *dev = musb->controller;
+	struct musb_hdrc_platform_data *plat = dev->platform_data;
+	struct omap_musb_board_data *data = plat->board_data;
 	unsigned long flags;
 	irqreturn_t ret = IRQ_NONE;
-	u32 epintr, usbintr, lvl_intr;
+	u32 epintr, usbintr;
 
 	spin_lock_irqsave(&musb->lock, flags);
 
@@ -346,9 +317,8 @@ eoi:
 	/* EOI needs to be written for the IRQ to be re-asserted. */
 	if (ret == IRQ_HANDLED || epintr || usbintr) {
 		/* clear level interrupt */
-		lvl_intr = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
-		lvl_intr |= AM35XX_USBOTGSS_INT_CLR;
-		omap_ctrl_writel(lvl_intr, AM35XX_CONTROL_LVL_INTR_CLEAR);
+		if (data->clear_irq)
+			data->clear_irq();
 		/* write EOI */
 		musb_writel(reg_base, USB_END_OF_INTR_REG, 0);
 	}
@@ -362,137 +332,85 @@ eoi:
 	return ret;
 }
 
-int musb_platform_set_mode(struct musb *musb, u8 musb_mode)
+static int am35x_musb_set_mode(struct musb *musb, u8 musb_mode)
 {
-	u32 devconf2 = omap_ctrl_readl(AM35XX_CONTROL_DEVCONF2);
+	struct device *dev = musb->controller;
+	struct musb_hdrc_platform_data *plat = dev->platform_data;
+	struct omap_musb_board_data *data = plat->board_data;
+	int     retval = 0;
 
-	devconf2 &= ~CONF2_OTGMODE;
-	switch (musb_mode) {
-#ifdef	CONFIG_USB_MUSB_HDRC_HCD
-	case MUSB_HOST:		/* Force VBUS valid, ID = 0 */
-		devconf2 |= CONF2_FORCE_HOST;
-		break;
-#endif
-#ifdef	CONFIG_USB_GADGET_MUSB_HDRC
-	case MUSB_PERIPHERAL:	/* Force VBUS valid, ID = 1 */
-		devconf2 |= CONF2_FORCE_DEVICE;
-		break;
-#endif
-#ifdef	CONFIG_USB_MUSB_OTG
-	case MUSB_OTG:		/* Don't override the VBUS/ID comparators */
-		devconf2 |= CONF2_NO_OVERRIDE;
-		break;
-#endif
-	default:
-		DBG(2, "Trying to set unsupported mode %u\n", musb_mode);
-	}
+	if (data->set_mode)
+		data->set_mode(musb_mode);
+	else
+		retval = -EIO;
 
-	omap_ctrl_writel(devconf2, AM35XX_CONTROL_DEVCONF2);
-	return 0;
+	return retval;
 }
 
-int __init musb_platform_init(struct musb *musb, void *board_data)
+static int am35x_musb_init(struct musb *musb)
 {
+	struct device *dev = musb->controller;
+	struct musb_hdrc_platform_data *plat = dev->platform_data;
+	struct omap_musb_board_data *data = plat->board_data;
 	void __iomem *reg_base = musb->ctrl_base;
-	u32 rev, lvl_intr, sw_reset;
-	int status;
+	u32 rev;
 
 	musb->mregs += USB_MENTOR_CORE_OFFSET;
 
-	clk_enable(musb->clock);
-	DBG(2, "musb->clock=%lud\n", clk_get_rate(musb->clock));
-
-	musb->phy_clock = clk_get(musb->controller, "fck");
-	if (IS_ERR(musb->phy_clock)) {
-		status = PTR_ERR(musb->phy_clock);
-		goto exit0;
-	}
-	clk_enable(musb->phy_clock);
-	DBG(2, "musb->phy_clock=%lud\n", clk_get_rate(musb->phy_clock));
-
 	/* Returns zero if e.g. not clocked */
 	rev = musb_readl(reg_base, USB_REVISION_REG);
-	if (!rev) {
-		status = -ENODEV;
-		goto exit1;
-	}
+	if (!rev)
+		return -ENODEV;
 
 	usb_nop_xceiv_register();
 	musb->xceiv = otg_get_transceiver();
-	if (!musb->xceiv) {
-		status = -ENODEV;
-		goto exit1;
-	}
+	if (!musb->xceiv)
+		return -ENODEV;
 
 	if (is_host_enabled(musb))
 		setup_timer(&otg_workaround, otg_timer, (unsigned long) musb);
 
-	musb->board_set_vbus = am35x_set_vbus;
-
-	/* Global reset */
-	sw_reset = omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET);
-
-	sw_reset |= AM35XX_USBOTGSS_SW_RST;
-	omap_ctrl_writel(sw_reset, AM35XX_CONTROL_IP_SW_RESET);
-
-	sw_reset &= ~AM35XX_USBOTGSS_SW_RST;
-	omap_ctrl_writel(sw_reset, AM35XX_CONTROL_IP_SW_RESET);
+	/* Reset the musb */
+	if (data->reset)
+		data->reset();
 
 	/* Reset the controller */
 	musb_writel(reg_base, USB_CTRL_REG, AM35X_SOFT_RESET_MASK);
 
 	/* Start the on-chip PHY and its PLL. */
-	phy_on();
+	if (data->set_phy_power)
+		data->set_phy_power(1);
 
 	msleep(5);
 
-	musb->isr = am35x_interrupt;
+	musb->isr = am35x_musb_interrupt;
 
 	/* clear level interrupt */
-	lvl_intr = omap_ctrl_readl(AM35XX_CONTROL_LVL_INTR_CLEAR);
-	lvl_intr |= AM35XX_USBOTGSS_INT_CLR;
-	omap_ctrl_writel(lvl_intr, AM35XX_CONTROL_LVL_INTR_CLEAR);
+	if (data->clear_irq)
+		data->clear_irq();
+
 	return 0;
-exit1:
-	clk_disable(musb->phy_clock);
-	clk_put(musb->phy_clock);
-exit0:
-	clk_disable(musb->clock);
-	return status;
 }
 
-int musb_platform_exit(struct musb *musb)
+static int am35x_musb_exit(struct musb *musb)
 {
+	struct device *dev = musb->controller;
+	struct musb_hdrc_platform_data *plat = dev->platform_data;
+	struct omap_musb_board_data *data = plat->board_data;
+
 	if (is_host_enabled(musb))
 		del_timer_sync(&otg_workaround);
 
-	phy_off();
+	/* Shutdown the on-chip PHY and its PLL. */
+	if (data->set_phy_power)
+		data->set_phy_power(0);
 
 	otg_put_transceiver(musb->xceiv);
 	usb_nop_xceiv_unregister();
 
-	clk_disable(musb->clock);
-
-	clk_disable(musb->phy_clock);
-	clk_put(musb->phy_clock);
-
 	return 0;
 }
 
-#ifdef CONFIG_PM
-void musb_platform_save_context(struct musb *musb,
-	struct musb_context_registers *musb_context)
-{
-	phy_off();
-}
-
-void musb_platform_restore_context(struct musb *musb,
-	struct musb_context_registers *musb_context)
-{
-	phy_on();
-}
-#endif
-
 /* AM35x supports only 32bit read operation */
 void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
 {
@@ -522,3 +440,215 @@ void musb_read_fifo(struct musb_hw_ep *hw_ep, u16 len, u8 *dst)
 		memcpy(dst, &val, len);
 	}
 }
+
+static const struct musb_platform_ops am35x_ops = {
+	.init		= am35x_musb_init,
+	.exit		= am35x_musb_exit,
+
+	.enable		= am35x_musb_enable,
+	.disable	= am35x_musb_disable,
+
+	.set_mode	= am35x_musb_set_mode,
+	.try_idle	= am35x_musb_try_idle,
+
+	.set_vbus	= am35x_musb_set_vbus,
+};
+
+static u64 am35x_dmamask = DMA_BIT_MASK(32);
+
+static int __init am35x_probe(struct platform_device *pdev)
+{
+	struct musb_hdrc_platform_data	*pdata = pdev->dev.platform_data;
+	struct platform_device		*musb;
+	struct am35x_glue		*glue;
+
+	struct clk			*phy_clk;
+	struct clk			*clk;
+
+	int				ret = -ENOMEM;
+
+	glue = kzalloc(sizeof(*glue), GFP_KERNEL);
+	if (!glue) {
+		dev_err(&pdev->dev, "failed to allocate glue context\n");
+		goto err0;
+	}
+
+	musb = platform_device_alloc("musb-hdrc", -1);
+	if (!musb) {
+		dev_err(&pdev->dev, "failed to allocate musb device\n");
+		goto err1;
+	}
+
+	phy_clk = clk_get(&pdev->dev, "fck");
+	if (IS_ERR(phy_clk)) {
+		dev_err(&pdev->dev, "failed to get PHY clock\n");
+		ret = PTR_ERR(phy_clk);
+		goto err2;
+	}
+
+	clk = clk_get(&pdev->dev, "ick");
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "failed to get clock\n");
+		ret = PTR_ERR(clk);
+		goto err3;
+	}
+
+	ret = clk_enable(phy_clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable PHY clock\n");
+		goto err4;
+	}
+
+	ret = clk_enable(clk);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to enable clock\n");
+		goto err5;
+	}
+
+	musb->dev.parent		= &pdev->dev;
+	musb->dev.dma_mask		= &am35x_dmamask;
+	musb->dev.coherent_dma_mask	= am35x_dmamask;
+
+	glue->dev			= &pdev->dev;
+	glue->musb			= musb;
+	glue->phy_clk			= phy_clk;
+	glue->clk			= clk;
+
+	pdata->platform_ops		= &am35x_ops;
+
+	platform_set_drvdata(pdev, glue);
+
+	ret = platform_device_add_resources(musb, pdev->resource,
+			pdev->num_resources);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to add resources\n");
+		goto err6;
+	}
+
+	ret = platform_device_add_data(musb, pdata, sizeof(*pdata));
+	if (ret) {
+		dev_err(&pdev->dev, "failed to add platform_data\n");
+		goto err6;
+	}
+
+	ret = platform_device_add(musb);
+	if (ret) {
+		dev_err(&pdev->dev, "failed to register musb device\n");
+		goto err6;
+	}
+
+	return 0;
+
+err6:
+	clk_disable(clk);
+
+err5:
+	clk_disable(phy_clk);
+
+err4:
+	clk_put(clk);
+
+err3:
+	clk_put(phy_clk);
+
+err2:
+	platform_device_put(musb);
+
+err1:
+	kfree(glue);
+
+err0:
+	return ret;
+}
+
+static int __exit am35x_remove(struct platform_device *pdev)
+{
+	struct am35x_glue	*glue = platform_get_drvdata(pdev);
+
+	platform_device_del(glue->musb);
+	platform_device_put(glue->musb);
+	clk_disable(glue->clk);
+	clk_disable(glue->phy_clk);
+	clk_put(glue->clk);
+	clk_put(glue->phy_clk);
+	kfree(glue);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int am35x_suspend(struct device *dev)
+{
+	struct am35x_glue	*glue = dev_get_drvdata(dev);
+	struct musb_hdrc_platform_data *plat = dev->platform_data;
+	struct omap_musb_board_data *data = plat->board_data;
+
+	/* Shutdown the on-chip PHY and its PLL. */
+	if (data->set_phy_power)
+		data->set_phy_power(0);
+
+	clk_disable(glue->phy_clk);
+	clk_disable(glue->clk);
+
+	return 0;
+}
+
+static int am35x_resume(struct device *dev)
+{
+	struct am35x_glue	*glue = dev_get_drvdata(dev);
+	struct musb_hdrc_platform_data *plat = dev->platform_data;
+	struct omap_musb_board_data *data = plat->board_data;
+	int			ret;
+
+	/* Start the on-chip PHY and its PLL. */
+	if (data->set_phy_power)
+		data->set_phy_power(1);
+
+	ret = clk_enable(glue->phy_clk);
+	if (ret) {
+		dev_err(dev, "failed to enable PHY clock\n");
+		return ret;
+	}
+
+	ret = clk_enable(glue->clk);
+	if (ret) {
+		dev_err(dev, "failed to enable clock\n");
+		return ret;
+	}
+
+	return 0;
+}
+
+static struct dev_pm_ops am35x_pm_ops = {
+	.suspend	= am35x_suspend,
+	.resume		= am35x_resume,
+};
+
+#define DEV_PM_OPS	&am35x_pm_ops
+#else
+#define DEV_PM_OPS	NULL
+#endif
+
+static struct platform_driver am35x_driver = {
+	.remove		= __exit_p(am35x_remove),
+	.driver		= {
+		.name	= "musb-am35x",
+		.pm	= DEV_PM_OPS,
+	},
+};
+
+MODULE_DESCRIPTION("AM35x MUSB Glue Layer");
+MODULE_AUTHOR("Ajay Kumar Gupta <ajay.gupta@ti.com>");
+MODULE_LICENSE("GPL v2");
+
+static int __init am35x_init(void)
+{
+	return platform_driver_probe(&am35x_driver, am35x_probe);
+}
+subsys_initcall(am35x_init);
+
+static void __exit am35x_exit(void)
+{
+	platform_driver_unregister(&am35x_driver);
+}
+module_exit(am35x_exit);